Professional Documents
Culture Documents
50stenfile Part2-VolumeIIEPCSchedulesforAURICHallBldg New
50stenfile Part2-VolumeIIEPCSchedulesforAURICHallBldg New
for
July 2016
Managing Director
TABLE OF CONTENTS
SCHEDULE-A: Site of the Project
1.0 SITE 5
SCHEDULE-B: Scope of works
1.0 Development of the project 13
2.0 Specifications and Standards 14
Appendix- B I Population Details 15
Appendix- B II Built-up Area Details 16
Appendix- B III Architectural Works 17
Appendix- B IV Civil and Structural Works 19
Appendix- B V Electrical Works 20
Appendix- B VI HVAC Works 27
Appendix- B VII Fire Fighting 32
Appendix- B VIII Plumbing 34
Appendix- B IX Fire Detection Alarm System, Smart Card Based 38
Access and CCTV Surveillance
Appendix- B X IGBC NC 41
Appendix- B XI Storm Water Drainage Network 42
Appendix- B XII Sewage Treatment Plant (Package STP) 43
Appendix- B XIII Solid Waste Management 44
Appendix- B XIV Integrated Bidding Management System (IBMS) / 46
Building Automation System (BAS)
Appendix- B XV Tender Drawings 58
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 2
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 3
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 4
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
SCHEDULE-A
Schedule A The Project Site
1.1 Site of the AURIC Hall Building located as a part of the CBD of AURIC - Shendra
Industrial Area is as described in Annexure-I of this Schedule-A.
1.2 The dates of handing over the Site to the Contractor are specified in Annexure-II of this
Schedule-A.
1.3 An inventory of the Site including trees and any other immovable property on, or attached to,
the Site shall be prepared jointly by the Employer Representative and the Contractor, and
such inventory shall form part of the Agreement.
1.4 The Draft Land Use Plan showing the AURIC Hall Building Site is specified in Annexure-
III. The applicable Development Control Regulations for the site are the Integrated Industrial
Area DCRs issued vide notification (No. TPB 4314/20/CR-32/2014/UD-11) dated August 1,
2015
1.5 Information on the topographic condition and levels within the site is given in Annexure-IV
1.7 The overall site plan for the AURIC Hall Building is given in Annexure-VI.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 5
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annexure I Site
1. Site
The AURIC Hall building site admeasures 11,335 sq.mts and is located in the North-western
part of the CBD campus of AURIC-Shendra. The AURIC Hall site has a 45m Road ROW on
the western side and the main access to the building is from the 45m Road ROW on the
northern side of the plot. The eastern side of the plot is proposed as an open space and a
potential public parking area where as the southern side is bounded by another developable
plot.
Figure 1: Location map of the AURIC Hall Building site within the CBD of AURIC-Shendra Industrial Area
Future infrastructure connections for water supply, power supply, ICT, sewerage network and
storm water disposal will be available long the northern and western road ROWs. Additional
common parking and open space is planned on the eastern side of plot.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 6
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The site for AURIC Hall Building lies within the following coordinates:
(refer Figure 1) (All coordinates are related to WGS 1984 UTM Zone 43N)
Plot Reference
Northing Easting
Point
1.1 Seismicity
The AURIC Shendra Industrial Area falls under the Zone III of the Seismic zoning map of India
IS: 1893-2002.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 7
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 8
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annexure III Proposed Land Use Plan for AURIC Shendra Industrial Area
(Schedule-A)
The site for the AURIC Hall Building superimposed on the land use plan for AURIC Shendra
Industrial Area is shown below.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 9
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. The site slopes from the north-west to the south-east and there is a general grade difference of
about 5 to 6 meters in the site. As such the site would have needed to be filled up by about 40
to 5 meters to bring it up to the road level however the proposed architectural design of the
AURIC Hall Building takes advantage of the terrain to create a Lower Ground Floor that helps
in constructing the building according to the sites topographical features.
There are no significant large trees, ponds, water bodies or HT lines within the plot boundary.
Tests to determine water level, details on soil condition and correct mapping of the rocky
outcrops will need to be conducted by the contractor. However, it is anticipated that hard or
fractured rock and soft rocky strata is just below the surface. A boundary map with
coordinates for reference of spot levels is provided below. FRLs are provided where a
finished road is anticipated as per the master plan. Elsewhere the existing ground levels are
provided as per the table below.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 10
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 11
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Environment clearance for AURIC - Shendra industrial Area has been obtain vide MOEFCCs
order dated June 18 2015
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 12
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Development of the AURIC Hall Building at Shendra, Aurangabad, shall include design and
construction of the following as described in this Schedule-B and in Schedule-C.
General
Contractor shall be responsible for making the facility fit for the intended purpose while performing
all of its obligations covered under the Contract Document in its entirety. The work shall be done in
accordance to the drawings approved by the statutory authorities.
Currently tender drawings and Design Criteria; Brief Technical Specifications for certain items of
work are available. Scope includes further detailing, as deemed necessary (without changing the
foot print of the proposed buildings, space planning and, design intent), developing required
specifications, preparing Good for Construction (GFC), coordinated drawings and construct in
accordance with the same. The scope shall also include preparation of as-built drawings before
handing over the work to the Employer, maintaining the Quality assurance & Quality control
(QA&QC) including control, corrective actions, reporting and arranging for regular inspections by
all concerned.
It will be the responsibility of the Contractor to obtain IGBC Gold rating for New Construction or
GRIHA 4 star rating for this building. The buildings are to be designed as per NBC, locally
applicable development control regulation and the latest applicable IIA norms and other statutory
requirements. The contractor shall also be responsible for obtaining necessary permits and
clearances including any applicable building permissions from the competent authority.
The Bidders are advised to visit the site before submitting the Proposal for the works.
The Scope includes all temporary works required for the completion of works, testing and
commissioning and handover till Defect Liability Period.
The Scope includes all consumables required for the completion of works, testing and
commissioning and handover till Defect Liability Period.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 13
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The AURIC Hall Building at Shendra, Aurangabad shall be designed and constructed in conformity
with the Specifications and Standards given in Schedule-D.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 14
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
sq.mt. Persons
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 15
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
Built-up area details are as given below in Table: 2
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 16
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The scope includes design, detailing, procurement, supply, construction, furnishing, testing
and execution for AURIC Hall Building at Shendra, Aurangabad.
Items of work include:
RCC Framed Structure
AAC Blockwork
Gypsum Plaster
Painting
Flooring & Finishing
Doors including Fire & Glass doors & Automatic Sliding Glass Doors.
Windows
Glazing and Faade works
Drywall Partition / Glass Partition
Ceiling Finishes
Wall Finishes
Waterproofing & insulation works
Polycarbonate roofing for Atrium
Fabrication including railing works
Movable Acoustic Partition
Toilet Cubicles
Compound Wall & Entrance Gate
Mechanical Stack Parking System
Any other works shown in the Appendix B XVI but not specifically mentioned above.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 17
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Contractor shall provide multiple options of the design of necessary element of
the Work for the Employers Engineer to review along with Employer / PMNC.
1.4 Mock-Up
Table No 3: Mockup
4.2 M x 4.2 M
2. Aluminium Screen
including all module sizes
Full height
3. MS decorative works Width Minimum 2 modules
4. Window glazing
One window module, Minimum with 2.4M, height 2.55M
5. Roofing 6M x 6M
Documents at Site
The Contractor shall maintain in a conspicuous place on the site a copy of development permission and a copy
of approved drawings and specifications
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 18
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The Contractor shall carry out, and be responsible for the design of the Works, of AURIC HALL,
ancillary structures, compound wall, fencing, security cabins, pavements, hardscape, water bodies,
drains, etc. The Scope of Work includes but is not limited to the following in relation to the design,
construction, and maintanance of the Works:
Prepare Design Basis Report based on the design intent and submit for approval.
Carryout out Structural Design based on approved Civil Structural Design Criteria.
Submit Structural stability certificate for all structures and components from government
authority at his own cost.
Proof checking by accredited agencies at bidders cost before submitting for the approval of
the Employer.
Setting out the works: Site Topographic Survey and Geotechnical Investigations as deemed
necessary by the Contractor. Site Clearing, Site Grading, and Excavation including
excavation for sump pits / lift pits.
Piling, foundation & substructure works.
Implement Anti termite treatment / Waterproofing / Insulation works.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 19
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
a.1 Scope
The scope of work shall cover the design, engineering, manufacture, assembly, testing at manufacturers
works / test labs, supply, delivery, properly packed for transport to site, unloading, storing at site of all
equipment, erection and commissioning, test at site, performance guarantee test run, training of
Employers personnel and handing over of the complete electrical system along with mandatory spares as
per the terms & conditions. The scope of work shall comprise of, but not limited to the following:
Power Supply system from nearest Compact Sub Station to Ring Main Unit.
High Side and Low Side equipment requirements such as Transformers and Switchgear.
Main Power Control Centers (PCC), Sub-Power Control Centers (Sub-PCC) and Motor
Control Centers (MCC).
Metering system.
Cable carrier system with necessary cabling accessories such as cable glands, lugs,
termination and jointing kits etc.
Fire proof sealing system comprising of fire stops and fire breaks.
Common area lighting and outdoor Lighting system comprising of lighting distribution boards,
lighting transformers, light fittings, lighting poles, Power socket, associate lighting
switches/sockets, associated cable, conduit and wiring.
DG synchronizing panel.
110V DC systems complete with one battery set, 2 x 100% BC (Float cum boost chargers),
DCDB.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 20
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All related civil works required for completion, commissioning but not limited to trenches,
foundations etc.
Reliability of service.
The design and equipment shall ensure satisfactory operation under variations of voltage 10%,
frequency (+) 5% to (-) 5%, combined voltage and frequency 10% for A.C., -15% to +10% for
DC as may be met under operating conditions, including those due to starting loads and short
circuit and other fault conditions.
The contractor shall calculate the total power requirements for the development by summing up
the power requirement for each floor in according to the design requirements.
The power allocation of 138 VA/sqm (13VA/sft for) load shall be provided for the office areas
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 21
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
including the common utilities such as plumbing, HVAC, firefighting, elevators, etc. This shall
cater for the lighting, power and other systems installed.
The contractor shall submit load calculation with the tender for the development taking into
account the acceptable diversity factors and providing a margin of (10%) contingencies for the
total power for the peak hour loads. The internal electrical power shall be tapped from the riser /
electrical room located on each floor.
System grounding.
RMU panel shall be metal clad, self-standing dust proof construction, outdoor cubicle type fitted
with incoming load break isolators and outgoing feeders as vacuum circuit breakers with
aluminium bus bar, fully draw out type. Degree of protection of RMU panel shall be IP65 or
better.
Required margin of (20%) shall be considered while sizing the bus bars and breakers for
switchgear
The relays in the 11kV RMU and 11kV HT panel shall be numerical type with IEC 61850
compatibility.
Two nos of 11/0.433kV, adequately sized dry type, two winding, 50 Hz, natural air cooled with
ON LOAD tap changer. The tap changer will be provided with
The transformer shall be 2 x 100% configuration i.e. it shall be sized such a way that if one
transformer fails other transformer capable to cater full load.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 22
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Transformer shall be designed such that the maximum efficiency shall be at 50% of its loading.
11/0.433 kV, Transformer LT side shall be suitable for terminating the 415V non- segregated
phase Busduct and HT side shall be suitable for cable terminations.
Non-segregated phase Busduct shall be TPN, Bus bar material shall be of high conductivity
electrolytic Aluminium conductor. Bus duct shall have degree of protection better than or equal to
IP-54.
415V rising main bus bar shall be of sandwich construction and made up of high conductivity
electrolytic aluminium conductor, non-ventilated design and the degree of enclosure protection
shall be IP 52.
Each Rising Main shall be equipped with an end feed unit / MCCB panel, at both ends.
Main LT panels shall be metal clad, self-standing dust proof construction, fully draw out type and
IP 54.
For feeders rated more than 400A, ACB with Numerical protection/built in microprocessor
release, discrete multi-function meters or metering as part of ACB shall be provided. For all other
rating feeders Microprocessor based MCCB shall be used. All ACB feeders shall be compatible
for remote control, metering and monitoring.
Incomer and busbar shall be rated for full load current of the total load connected plus a margin of
20%, rounded off to the next standard rating. All outgoing feeder modules from each PCC shall
be rated for the full load current plus 10% margin, rounded off to the next standard rating. All
PCC shall be provided with 20% spare feeders.
Incoming feeders shall be provided with ACB breaker with Numerical protection relay
compatible with IEC 61850.
For remote metering in SCADA for current, line voltage, bus voltage, kW, KWH either separate
transducers or soft data shall be taken through communication of Numerical relays/MFMs looped
and interfaced to SCADA. Architecture shall be submitted for approval.
f. Control Philosophy
Each switchgear whose incomer, buscoupler and outgoing breakAer feeder are controlled from
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 23
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
SCADA shall be provided with two IEC-61850 compliant managed ethernet switches. The IEC-
61850 compliant numerical relays shall in turn be connected to both these switches either to form
a ring or radially connected, so that loss of one connection does not result in loss of
communication with any device. These switches shall be provided with fibre optic (FO) ports for
interconnection with other switchgear switches, which form part of the IEC-61850 LAN network.
Further interconnection to the SCADA shall be through redundant server.
g. APFC Panel
Automatic Power Factor Correction (APFC) capacitor panels with capacitor bank of adequate
kVAR rating to maintain the power factor of 0.98 lag at main LT panels.
All Poly Propylene (APP) type Capacitor banks shall be housed in APFC Panel cabinet.
h. Motors
Motors shall be energy efficient (IE2) squirrel cage induction type, TEFC, IP-55 enclosure
(including terminal boxes and bearing housing) with Class-F insulation (and temperature rise
limited to Class B).
Lockable Stop Push Button (press to stop and key to release) shall be provided near to the each
equipment. The enclosure shall be engineering plastic (scratch resistant), weather proof, corrosion
resistant, dust and vermin-proof, suitable for mounting on wall or structures. The enclosure shall
have degree of protection not less than IP55.
i. DC System
The DC system shall be designed to cater the loads for control, protection and indication of 11kV
switchgear, 415V breaker controlled feeder, control panel, DG AMF panel, RTCC panel shall be
designed for 110V DC battery with 2 hours back-up time.
110V, 2 x 100%, float cum boost charger with a common 100% tubular lead acid battery shall be
provided which shall be located in utility building ground floor level.
j. DG Set
Emergency DG set shall be designed for only emergency services i.e. common area lighting, Fire
Fighting services, partial set of lifts, utility pumps, etc. Considering the same, DG Set rating shall
be approx. 2 nos. 500KVA at 85% loading. The Prime rated DG set shall be an Indoor type open
construction mounted on base frame through anti vibration mounts. The cooling system for DG
set is radiator type. The DG room shall be acoustically insulated along with panels to limit the
noise in line with the norms as set by pollution control board.
k. Solar PV System
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 24
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Grid interactive solar PV system is proposed to cater this requirement. The system shall be with
inverter mounted with PV panels.
Solar module shall be multi crystalline type, employing lamination technology using established
polymer (EVA) and Tedlar / Polyester laminate.
Power cables and control cables shall run in different shafts. Separate riser and trays shall be
provided for the LV system.
All cabling/wiring works shall be concealed wiring except for risers and in other areas where
public or tenants do not have access or approved areas by the Employer.
m. Lighting system
Electronic ballasts should be used. Light fittings should be installed with effective reflectors.
Mercury light fittings should not be used; instead Metal halide/sodium light fittings shall be
used.
The luminaries shall be selected to suit architectural, functional and aesthetic requirements.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 25
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
n. UPS system
UPS are provided for critical system loads, servers and work stations, BMS, FACP (Fire Alarm
Control Panel) & FARP (Fire Alarm Repeater panel), CCTV and Emergency lighting etc. with
3hrs battery back-up.
The UPS will be 3ph to 3 ph, 50 Hz, Modular type, On-line, Redundant UPS power supply and
with static bypass. The UPS output will be connected to the UPS DB for further distributions.
During normal operation, the AC Supply will be fed to UPS Distribution boards through UPS
and a small trickle charging current will be feeding to tubular lead acid battery for charging.
Once the AC supply fails, for a momentary time till the DG picks up the battery will feed the
UPS distribution loads through UPS.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 26
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1 Scope
The scope of works shall cover the design, engineering, Supply, Installation, Testing and commissioning
of the complete Air-Conditioning (air cooled chillers) and Ventilation (ACV) System of AURIC
Building. The scope includes all the related things like procurement, manufacture, testing at
manufacturers works, packaging, transportation, shipping, unloading at port, transportation to site,
unloading, storage, insurance, transportation from stores to erection site etc.
AURIC Building will be an IGBC (NC) Gold Building (minimum) and IGBC Green New Buildings v 3.0
- Fourth Addendum August 2015 to be followed.
Inside design temperature for all areas except server room should be: 24 +/- 1 C.
Inside design temperature for Server Room and Control Room should be: 22 +/- 1 C with
relative humidity of 50% +/- 5%.
Ambient Conditions of Aurangabad to be followed are :
Summer Ambient @ 1%
Grains / Lb : 76
For occupancy details, heat load summary sheet to be followed.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 27
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The air conditioning system shall preferably comprise central chilled water plant consisting of
chillers, ideally suited for the nature of this project, pumps providing chilled water to air
handling units, fan coil units complete with control panels, pipe works, valves, fittings,
ductworks, grilles, dampers, etc. with necessary insulation / acoustic works.
Cooling load requirement shall be based on heat load calculation to be sybmitted with tender, the
no of chillers and pumps shall be configured for the duty and minimum one no of stand by
operation. The building data to be considered.as follows:
Exterior Wall/ Spandrel a.U value (for Without screen) = 0.34 BTU/hr.
ft. F
b.U value (for With screen) = 0.24 BTU/hr. ft.
F
Mechanical ventilation shall be provided to escape stairs, toilets, kitchens, services and
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 28
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
equipment areas and any other areas to comply with the authorities requirements. All M&E
rooms shall be adequately ventilated to ensure maximum room temperature to be maintained not
more than 30 C.
Life Safety System parameters for lift well /stairwell pressurization, car park and smoke exhaust
shall be followed as.
Sufficient space shall be provided for maintenance and repair works in the plant room.
Mechanical Ventilation System should be provided in plant room to ensure proper operating
condition is achieved. All pumps and chillers should be provided with proper drain pipe system
to the nearest floor traps. Floor should be waterproofed. Balancing valves & isolating valves
(butterfly / gate / ball) flow valves should be installed in the chilled water and condenser water
system. Appropriate vibration and acoustics measures should be implemented.
Vibration isolators for all Air-conditioning and Ventilation equipment.
Complete framework required for mounting grills/louvers in masonry works is deemed to be
included in Air-conditioning and Ventilation Contractor scope.
Painting of equipment, piping and supports of the Air-conditioning and Ventilation system as per
National Building Code (NBC) or standards of the employer.
Automatic controls and instruments including control cabling.
Wiring and earthling from MCC panels to various refrigeration, air conditioning and mechanical
ventilation equipment, control wiring and interlocking.
All the Air-conditioning and Ventilation system shall be provided with the connectivity to
Building Management System (BMS) with a potential free contact. The Contractor shall provide
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 29
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
the minimum interface & connectivity of the Air-conditioning and Ventilation system to the
BMS
VFD & VAV for AHUs, VFD for secondary pumps, life safety etc. to be considered.
Provide larger size sleeve for crossing of pipe, conduits & cables through fire rated
wall/partition. The sleeve shall be sealed with fiberglass and fire sealant.
Fire/smoke dampers shall be installed to maintain integrity of fire compartmentalization. The
vendor shall submit installation details and obtain approval prior to execution at site.
Balancing, testing and commissioning of the entire Air-Conditioning and mechanical ventilation
system.
The complete electrical work related to air conditioning services, shall be carried out by
Contractor.
The scope includes the associated civil works like providing RCC/PCC foundations, pedestals
for equipment like water chilling machines, AHUs, pumps
& fans etc., and necessary plumbing works like providing floor and condensate drains in the
equipment rooms.
All associated Electrical Works are also in the scope of Contractor. These shall be installed in
accordance with approved shop drawings of, and under direct supervision.
All associated Plumbing Works are also in the scope of Contractor. Detailed specifications are
mentioned in the electrical section. These shall be installed in accordance with approved shop
drawings of, and under direct supervision.
a) Providing soft makeup water (Commercial hardness 0 ppm and pH 6.5 to 8.0) at chilled water
expansion tank.
b) Providing sump pumps and necessary piping for drainage of air conditioning plant room and
other machine rooms located below ground level.
c) Providing floor drains in cooling tower area and in air handling unit rooms.
d) Disposal of condensate drain from fan coil units / ceiling suspended units beyond the
condensate drain riser.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 30
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The battery limits on the low side works to be considered are as under:
For the Ground, Fifth Floor and Public Area low side works, complete air-conditioning system to be
considered including the BTU meter, AHU / CSU / PEC Units, Valve Station, AHU / CSU Panel,
Cabling, Fire and Volume Control Dampers, VFD, VAV Boxes, Ducting, Duct insulation, Grilles /
Diffusers, etc.
For the First to Fourth Floors, low side works, air-conditioning system to be considered includes the BTU
meter, AHU / CSU / PEC Units, Valve Station, AHU / CSU Panel, Cabling, Fire and Volume Control
Dampers, VFD, VAV Boxes, etc. However, Ducting, Duct insulation, Grilles / Diffusers, etc. not to be
considered since internals will be executed by the end user / tenant.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 31
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The Scope of works shall cover the design, engineering, Supply, Installation, Testing and commissioning
of the complete Fire Fighting system including Fire alarm system of AURIC Building. The scope
includes all the related things like procurement, manufacture, testing at manufacturers works, packaging,
transportation, shipping, unloading at port, transportation to site, unloading, storage, insurance,
transportation from stores to erection site etc.
Main design components include Wet risers and the hydrant System including all pumps and
pipe networks.
Pumps shall be of three types, namely 2400 lpm & 85 m head electric, 2400 lpm
85 m head diesel driven, and 200 lpm & 85 m head jockey pumps. Pump capacity should be as
per NBC/NFPA standards or as per local fire CFO requirement.
All Accessories, but not limited to field instruments like pressure gauge & pressure switch and
control cabling including junction box, erection hardware, etc., to MCC & diesel engine control
panel should be included.
Electrical panels, Cabling & earthling from MCC panels to various firefighting system, control
wiring & interlocking.
Instrumentation and Control equipment shall be complete with primary elements, initiating
contacts for alarms, instrument impulse lines, fittings, power and control cables with suitable
glands and terminations and instrument installation hardware.
4mm thick wrapping & coating for underground piping with proper testing.
Sprinkler System for the complete development (within the scope of this contract).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 32
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The complete electrical work related to Firefighting including, but not limited to installation of
pumps, shall be carried out by Contractor.
The Scope includes the associated works like Structural works for pipe supports for above
ground pipes, wall supports, hose cabinet supports, etc., Civil works like wall opening, chipping
of foundation, grouting of foundations, sand filling and compacting for underground pipes, etc.
Painting of equipment, piping, supports etc. with 2 coats of primer & 2 coats of synthetic enamel
as per IS: 5 shade 536 (Fire Red).
Supply of One set of special erection and maintenance tools and tackles.
Anchor fasteners required for pipe supports of all the systems which are engineered by vendor
and all anchor bolts, nuts, washers and inserts to be embedded in concrete for the equipment and
piping.
Shop inspection (in Vendors works & at project site after installation along with all required
calibrated measuring instruments).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 33
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The Scope of works shall cover the design, engineering, Supply, Installation, Testing and Commissioning
of the complete Plumbing system including Internal and External Water Supply, Internal and External
drainage including Sewerage, Storm water drainage, Rain water harvesting system of AURIC Building.
The scope includes all the related things like procurement, manufacture, testing at manufacturers
works, packaging, transportation, shipping, unloading at port, transportation to site, unloading, storage,
insurance, transportation from stores to erection site etc. The scope shall also include compliance to
IGBC NC for Gold rating.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 34
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Works to include for air vents, PRV, water meters, valves, pressure gauges, water hammer
arrestors, Nahni traps, Floor gratings, Gully trap, grease trap, man holes, inspection chambers,
required piping connections etc.
Required capacity hydro pneumatic system with required controls and instruments at Pump
Room level for each domestic water system and flushing water system with comprising 2 nos. of
working pumps of 50% cap. of total flow rate required & 1 no. of same cap. standby pump for
the building. Flow rate for domestic pump is as per design requirement.
Required capacity booster pumps with pressure sensor system with required controls and
instruments at terrace level for each drinking water system and flushing water system with
standby for each building.
Cabling & earthling from MCC panels to various plumbing/ sanitary system, control wiring &
interlocking.
Field instruments like pressure gauge & pressure switch and control cabling including junction
box, erection hardware, etc., to MCC
Instrumentation and Control equipment included in the package unit shall be complete with
primary elements, initiating contacts for alarms, instrument impulse lines, fittings, power and
control cables with suitable glands and terminations and instrument installation hardware.
Supply & Installation of following complete Sanitary Fixtures and Fittings as per the model and
make mentioned in the tender specifications.
a) EWCs (Model: Hindware Make cat.no.20024, Viega concealed flush tank cat. Nos. 8864.4 2 /
4 ltrs).
b) Lavatory basin (Model: Below counter wash basin Hindware (493 X 413) cat.no. 10051
c) Urinal with sensor system (Model: 60002 Hindware & Jaguar Concealed urinal flush
sensor 51077).
d) Pantry sink.
e) Shower assembly.
f) Cocks & taps.
g) ABS Rinsing spray.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 35
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
h) Janitor sink.
i) Hand drier, tower ring, soap dispenser, toilet paper holder, twin coat hook etc.
j) Following Jaguar make sanitary fixtures shall be considered:
Continental Bib cock straight CON. 047.
Continental Pillar cock straight SNR-CHR-51021.
k) Fixture flow rate are as per below table however contractor needs to ensure same is in compliance
with IGBC requirement.
2) Urinal 1 LPF
The complete electrical work related to Plumbing works including, but not limited to cabling and
earthing of various fixtures and control wiring shall be carried out by Contractor.
The Scope includes the associated works like Structural works for pipe supports for above
ground pipes, wall supports, hose cabinet supports, etc., Civil works like wall opening, chipping
of foundation, grouting of foundations, sand filling and compacting for underground pipes, etc.,
Painting of equipment, piping, supports etc. with 2 coats of primer & 2 coats of synthetic enamel
as per relevant IS codes.
Start up and Essential spares.
Recommended spares for 5 years operation
Anchor fasteners required for pipe supports of all the systems which are engineered by vendor
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 36
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
and all anchor bolts, nuts, washers and inserts to be embedded in concrete for the equipment and
piping.
Supply of One set of special erection and maintenance tools and tackles.
Cutting holes, chases & like through all types of walls /floors and finishing for all services
crossings, including sealing, frame works, fire proofing, providing sleeve, cover plates, making
good structure and finishes to an approved standard.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 37
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Appendix B IX Fire Detection Alarm System, Smart Card Based Access and CCTV
Surveillance
(Schedule-B)
1.1 Scope
The scope includes design, detailing, procurement, supply, installation, equipping, testing,
commissioning and execution of ICT Solution consisting of Fire Detection & Alarm System and Public
Address system, Smart Card based Access Control System, CCTV Video Surveillance System, Boom
Barriers, Network Management System, Visitor Management System, BMS for common areas of
AURIC Building block, BEC block, Utility block and ancillary structures, in accordance with the
tender requirements.
The system shall comprise of heat and smoke detectors, manual call points, hooters and Public
Address System.
The system shall comprise of microprocessor based addressable fire detection system.
(i) Integrated smoke and heat detectors.
(ii) Manual call points.
(iii) Hooter sounders with flashers.
(iv) Ceiling mounted speakers for PA system.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 38
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
printing with colour in front & B&W on back. Plastic Card Holder with Lanyard).
The main objective is to monitor and record the activities, movement of people and vehicles
through entry points inside the building, to monitor perimeter.
Cameras to be positioned at all areas to enable a total secured building.
Video Cameras should be - IP Mini Dome Color IR, 2 MP, Varifocal lens
4-meter boom barrier with safety photocell, support stand, magnetic loop detector, copper loop
and other accessories, transponder technology system, key operated selector switch, flashing
light etc.
(i) 12 Port Managed Network Edge / Access Switch, 10/100 Mbps with POE.
(ii) 8 Port Managed Network Edge / Access Switch, 10/100 Mbps.
(iii) 24 Port Managed Network Aggregation Switch, 10/100 Mbps.
(iv) Network Management Server / Workstation with software.
(v) Network Rack (42U).
(vi) PVC Conduit pipe + installation.
(vii) AT6 Cable + installation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 39
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All associated electrical / civil work related to above works including, but not limited to cabling,
earthing and structural works for support / fixing of various fixtures, wall openings, grouting,
foundations, sand filling and control wiring shall be carried out by Contractor.
The Contractor will carry-out any interfacing / Integration of the systems as required between
the systems and also with the BMS (Lift, AHU, Lighting, DG Set Panels)
Required UPS Power only will be made available by the Employer. The power cabling &
Ethernet / Optical Fiber cabling, Ethernet Switches and other network hardware shall be
provided by the Contractor.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 40
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Appendix B X IGBC NC
(Schedule-B)
1.1 Scope
The objective of the Contractor is to help the Employer meet all sustainability goals (including IGBC
NC) set for the project. The Contractor shall also help the Employer secure IGBC NC-Gold rating for
this project through IGBC NC Ver 3
The Contractor shall facilitate complete green-building certification process for the project.
The Contractor shall assess all available building data to understand and maintain current design
goals and strategies for detail design and construction. All available building information shall
be made available to the Contractor for the same. In case the information is not available, the
Contractor shall make suitable assumptions and cross check with the Employer (including IGBC
NC facilitator).
The project is registered with IGBC for IGBC NC certification and is aspiring for Gold rating
under IGBC NC V 3.0 for India . To achieve Gold rated IGBC NC certification the project has to
follow certain best engineering practices and select materials that are compliant with the IGBC
NC rating system. Hence the following roles and responsibilities have been identified for the
Contractors to ensure that the project achieves this target.
In addition, the Contractor will appoint a suitable Contractor/consultant for the documentation
and submission of documents to IGBC for approval.
The appointed consultant shall be responsible for the certification of the building as IGBC NC
Gold certified building.
All associated works like collection of Information, assessment and documentation of
information, final submission and weekly reporting to the Employer on the progress is included.
This should also include all the analysis but not limited to energy analysis, daylight simulation
etc.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 41
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The Scope of Work for proposed storm water drainage system under this contract includes but is not
limited to the following in relation to the design, supply, construction, testing and commissioning of
storm water drainage system of the Works.
Storm water collection and disposal system.
Excavation, dewatering, ramming, refilling, and disposal of surplus excavated soil for pipe / box
trench.
Length and conduit details of storm Drains in side AURIC Building plot is provided in Table 11
below:
Table 11 : Length and conduit details of storm Drains in side AURIC Building plot
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 42
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The scope shall include design and construction of the following as described in this Schedule-B and in
Schedule-C.
This bid is for the design, engineering, manufacture, supply, installation, testing and commissioning and
operation of package STP system excluding the Civil Work execution in line with the details given in
this document.
The capacity of the STP is approx. 105KLD. However, Bidder to design the actual capacity as required
for the project.
The scope of work includes all mechanical and bought-out equipment, piping, electrical and
instrumentation work. The turnkey supplier shall provide all the drawings and details as required for the
Consultant to carry out civil design and for a separate civil Contractor engaged by the Client at site to
carry out the civil work for the STP. Turnkey supplier has to consider visits to site at key stages for
guiding the civil Contractor, if required, to ascertain that work is carried out as per the drawing
requirements.
The Sewage Treatment Plant (STP) will be based on MBR Process (Membrane Bioreaction) and to be
designed based on the various details mentioned in i.e. Basis of design. The sewage treatment plant will be
suitable for semi-automatic operation, wherein starting/tripping/ of all the pumps will be controlled by
level sensors provided in the tank. Pumps will start once water level reaches desired high level and will
stop once water level in the tank lowers down to desired low level. Filter backwash operations will be
semi-automatic. All other operations including chemical dosing and sludge draw off will be suitable for
semiautomatic operation. Various details of sewage treatment plant will be as mentioned below.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 43
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
1.1 Scope
The scope of works is to ensure that the entire solid waste generated in the AURIC Building is treated and
managed. It includes collection and segregation of waste at source using colour coded bins under hygienic
conditions and then treating it using organic waste composter including disposal of recyclable and inert.
Collection at pre-informed time (two times a day) from all waste generation source.
Provision of three colour coded bins (wet, dry and recyclables) for waste collection from
common areas.
The capacity of the OWC is approx. 225 kg capacity. However Bidder to design the actual
capacity as required for the project.
Demolishing the existing structures, if any, on the site.
Supply, erection testing & commissioning of the mechanical and Electrical & Instrumentation
equipment
Providing walkways and platforms of minimum 1.2 m width as access.
The recyclables like paper, plastic and metal to be stored in the utility area for a maximum
duration of 15 days and then be sold to authorised vendors for handling recyclables.
The inert to be stored in utility waste handling area and will be sent to the nearest authorised
municipal solid waste landfill site.
Any hazardous waste generated from the complex like used DG oil; old batteries etc. to be
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 44
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, construction, supply, erection, testing and commissioning of approx. 225 Kg capacity.
Composter with walkway and platform 1.2 m wide.
Integration with other civil, mechanical, and electrical, integration with proposed architectural,
construction of the main structure.
Associated civil, electrical and other services works.
Supply of all spares required during performance run and during 36 months of O & M period.
The recyclables like paper, plastic and metal to be stored in the utility area for a maximum
duration of 15 days and then be sold to authorised vendors for handling recyclables.
The inert to be stored in utility waste handling area and will be sent to the nearest authorised
municipal solid waste landfill site.
Any hazardous waste generated from the complex like used DG oil; old batteries etc. to be
handed over to SPCB authorized hazardous waste handling vendors.
The compost from the treatment of organic waste should be used for landscaping in the AURIC
Hall building Complex.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 45
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.2 Scope
The System provider shall furnish and install a fully integrated Building Management System (BMS),
incorporating distributed control techniques and standard open communication networks. The system shall
be implemented as an integrated, open solution, which enables Service Center connectivity through
standard Building Operating System (BOS) interface.
The integrated systems shall include controls and monitoring of the whole building (BMS and Security)
and common areas wherever applicable.
Integrated Building Management System shall include the control and monitoring of the following
subsystems:
Elevator Control.
Pump Control.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 46
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The IBMS shall consist of software and hardware; the software program configured in a hierarchical
manner that integrates the various subsystems.
System integration shall enable significantly lower energy consumption, real-time control and
monitoring, and dynamic graphics according to needs. System integration shall create better
environmental air quality, radically improved energy performance and increased water efficiency,
according to requirements of IGBC NC and other Green Building standard and initiatives.
System integration shall also allow for efficient system maintenance and full-scale service
provisioning with radically lower cost and better quality services. Easy access to building systems shall
ensure that everything is in perfect condition and functions in the optimal way at all times. Should
anything disturbing happen, immediate response shall be available. Integration shall facilitate
undisturbed conditions in the building and sustainable development through minimized energy
consumption, first- class security and significantly lower life cycle costs.
The system shall be implemented as an integrated, open solution, which enables Service Center
connectivity through standard Building Operating System (BOS) interface.
Service Level.
Management Level.
Control Level.
Field Level.
The system shall be completely modular in structure and freely expandable at any stage. Each level of the
system shall operate independently of the next level up as specified in the system architecture. For
example, Control Level shall operate independently without support from Management Level. The system
shall be fully consistent with the latest industry standards.
To enable efficient functional system integration and to provide maximum flexibility and to respond to
changes in the building use, the system offered shall support the use open protocol and Internet
communication technologies.
1.4.1 Service Level shall allow the systems to be connected without additional software to one or
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 47
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
several Service Center(s), for providing centralized remote monitoring, alarm and fault
detection of connected building management and security systems.
1.4.2 Management Level shall provide a uniform view to all systems through the open Building
Operating System (BOS) platform. All the systems - controls of cooling, ventilation and
lighting, consumption measurements, access controls, fire alarms and CCTV systems - shall be
integrated with the BOS using device drivers.
1.4.3 Control Level shall consist of a distributed network of smart controllers, which communicate
to each other subsystems using compatible interfaces. Connectivity towards Management
Level shall utilize standard TCP/IP protocol.
1.4.4 Field Level shall consist of sensors and devices with industry standard interfaces.
1.4.5 Systems shall be accessed through the Building Operating System (BOS). System must have
two main user interface types professional user interface and occupant user interface.
The system shall enable a client-based User Interface for professional usage and for central monitoring
of systems (Service Center usage). The professional User Interface shall allow for at least the
following:
Intruder alarms.
Fire alarms.
Video monitoring.
Set-point adjustment.
Control optimization.
Trending.
Preventive maintenance.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 48
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The professional User Interface shall be implemented as a client application, which includes an
automatically adapting tree structure of the building, buildings parts, individual spaces, different systems
and parts of systems. The tree structure can be used for navigation through the system.
All subsystems connected to Building Operating System can be accessed through the same graphical User
Interface. The client software can be installed to unlimited number of remote computers or laptops. The
client software shall allow for remote Internet usage of several sites using the same client.
The professional User Interface shall show system views, floor plan views, trend view, alarm view and
event log view per building and system layer. Any alarm shall be shown in red color in both graphical
views and tree structure. Each alarm message shall include shortcut to relevant graphical system and floor
plan view.
The browser-based occupant User Interface shall allow for at least the following actions:
Manual controls.
Door controls.
Camera views.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 49
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The I/O Summary (Hard Points and Soft Points) and IBMS Objective is as under:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 50
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 51
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 52
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 53
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 54
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 55
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 56
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 57
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Schedule-B)
ARCHITECTURAL
15 AH/T/A2.11 DW Schedule
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 58
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ARCHITECTURAL
22 AH/T/A3.1 Elevations 1
23 AH/T/A3.2 Elevations 2
24 AH/T/A3.3 Elevations 3
25 AH/T/A3.4 Elevations 4
26 AH/T/A3.5 Sections 1
27 AH/T/A3.6 Sections 2
28 AH/T/A3.7 Sections 3
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 59
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ARCHITECTURAL
STRUCTURAL
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 60
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
STRUCTURAL
HVAC
Sr. No Drawing No. Content
1 DCE/7692/HVAC/01/R- Lower Ground Hvac Layout
2 DCE/7692/HVAC/02/R- Ground Floor Hvac Layout
3 DCE/7692/HVAC/03/R- First Floor Hvac Layout
4 DCE/7692/HVAC/04/R- Second Floor Hvac Layout
5 DCE/7692/HVAC/05/R- Third Floor Hvac Layout
6 DCE/7692/HVAC/06/R- Fourth Floor Hvac Layout
7 DCE/7692/HVAC/07/R- Fifth Floor Hvac Layout
8 DCE/7692/HVAC/08/R- Fifth Floor Hvac Layout
LV
Sr.No Drawing No. Content
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 61
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
PLUMBING
Sr. No Drawing No. Content
DCE/7692/PLUMBING-STORM
2 Lower Ground Storm Water Layout
WATER/02/R-
DCE/7692/PLUMBING-STORM
4 Ground Floor Storm Water Layout
WATER/04/R-
DCE/7692/PLUMBING-U.G.TANK
11 U.G. Tank Piping Layout
PIPING/11/R-
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 62
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
DCE/7692/PLUMBING
12 Plumbing Schematic Layout
SCHEMATIC/12/R-
DCE/7692/PLUMBING-TYPICAL
13 Typical Floor Water Supply Layout
FLOOR WATER SUPPLY/13/R-
FIRE FIGHTING
Sr.No Drawing No. Content
DCE/7692/FIRE FIGHTING-OVER
9 Over Head Tank Layout
HEAD TANK/09/R-
DCE/7692/SCHEMATIC FIRE
10 Schematic Fire Fighting Piping Layout
FIGHTING PIPING/10/R-
ELECTRICAL
Sr. No Drawing No. Content
DCE/7692/ELECTRICAL-
1 Lower Ground Lighting Layout
LIGHTING/01/R-
DCE/7692/ELECTRICAL-
2 Ground Floor Lighting Layout
LIGHTING/02/R-
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 63
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
DCE/7692/ELECTRICAL-
3 First Floor Lighting Layout
LIGHTING/03/R-
DCE/7692/ELECTRICAL-
4 Second Floor Lighting Layout
LIGHTING/04/R-
DCE/7692/ELECTRICAL-
5 Third Floor Lighting Layout
LIGHTING/05/R-
DCE/7692/ELECTRICAL-
6 Fourth Floor Lighting Layout
LIGHTING/06/R-
DCE/7692/ELECTRICAL-
7 Fifth Floor Lighting Layout
LIGHTING/07/R-
DCE/7692/ELECTRICAL-
8 Terrace Floor Lighting Layout
LIGHTING/08/R-
DCE/7692/ELECTRICAL-
9 Lower Ground Socket Layout
SOCKET/01/R-
DCE/7692/ELECTRICAL-
10 Ground Floor Socket Layout
SOCKET/02/R-
DCE/7692/ELECTRICAL-
11 First Floor Socket Layout
SOCKET/03/R-
DCE/7692/ELECTRICAL-
12 Second Floor Socket Layout
SOCKET/04/R-
DCE/7692/ELECTRICAL-
13 Third Floor Socket Layout
SOCKET/05/R-
DCE/7692/ELECTRICAL-
14 Fourth Floor Socket Layout
SOCKET/06/R-
DCE/7692/ELECTRICAL-
15 Fifth Floor Socket Layout
SOCKET/07/R-
DCE/7692/ELECTRICAL-
16 Terrace Floor Socket Layout
SOCKET/08/R-
DCE/7692/ELECTRICAL-
17 Lower Ground Service Layout
SERVICE/01/R-
DCE/7692/ELECTRICAL-
18 Ground Floor Service Layout
SERVICE/02/R-
DCE/7692/ELECTRICAL-
19 First Floor Service Layout
SERVICE/03/R-
DCE/7692/ELECTRICAL-
20 Second Floor Service Layout
SERVICE/04/R-
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 64
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
SERVICE/05/R-
DCE/7692/ELECTRICAL-
22 Fourth Floor Service Layout
SERVICE/06/R-
DCE/7692/ELECTRICAL-
23 Fifth Floor Service Layout
SERVICE/07/R-
DCE/7692/ELECTRICAL-
24 Terrace Floor Service Layout
SERVICE/08/R-
DCE/7692/ELECTRICAL-MAIN SLD
25 Main SLD 01
01/01/R-
DCE/7692/ELECTRICAL-MAIN SLD
26 Main SLD 02
02/02/R-
DCE/7692/ELECTRICAL-EARTHING
27 Earthing Schematic
SCHEMATIC/01/R-
DCE/7692/ELECTRICAL-LIGHTING
28 Lightning Arrestor Layout
ARRESTOR/01/R-
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 65
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Contractor shall construct the Project Facilities in accordance with the provisions of this Schedule C.
Such Project Facilities shall include:
1.0 Architectural
1) Compound wall in block work with intermittent MS jali panels and piers also in block work.
2) 03 Entry / Exit gates with CC TV surveillance.
3) 03 Security Cabins
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 66
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The building will be provided with permanent electrical supply, DG & UPS backup power facilities in
accordance with the provisions as per Schedule B & D.
1) 1 x 2000vkVA, prime rated, 415V, 50Hz, Transformer and 2 x 500kVA DG sets with associated
accessories.
2) Normal and emergency light fixtures.
3) Building facade lighting, gate illumination, bollards etc.
6.1 HVAC
The building will be provided with air conditioning, mechanical ventilation and exhaust facilities in
accordance with the provisions as per Schedule B & D.
The building will be provided with Firefighting facilities including wet risers, sprinklers, fire hydrants and
portable fire extinguishers in accordance with the provisions as per Schedule D & I and requirements of
the statutory authorities.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 67
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2) Fire pumps, external and internal hydrant pumps, sprinkler pumps, jockey pumps
- electric & diesel engine driven
3) Piping connection between UG tanks to the suction header, pump connections, further
distribution with required valves, accessories etc.
4) Required electrical MCC cum instrument control panels with controls like pressure switch etc. to
make the system to work automatically.
5) Fire extinguishers, internal hydrants and yard hydrants.
6) Piping connection between OHT to the wet riser with required valves, accessories etc.
7) Internal hydrants with hose reel box, fire hoses, nozzle etc. at each level.
8) Piping, valves, accessories required for the complete system.
The building will be provided with sanitation facilities including fully functional and equipped
washrooms and potable water supply in accordance with the provisions as per Schedule B & D.
1) Underground (UG) water tanks for each potable, non-potable and firefighting system in basement
of utility building.
2) Individual transfer pumps (working & standby) for each system (potable and non- potable) in
utility building.
3) Booster pumping systems with sensor are proposed for top 3 levels of each building.
4) Complete sewage, waste and rain water piping.
5) Complete water supply (both potable & non-potable) distribution from OHT to each level.
6) Piping connection between UG tanks to the suction header, pump connections etc.
7) Sanitary fixtures and fittings.
8) Piping, valves, accessories required for the complete system.
9) Rain water collection from roof top
Dedicated covered storage for HVAC material and equipment. Storage area should be clean and
dry.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 68
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1) Excavation, dewatering, ramming, refilling, and disposal of surplus excavated soil for pipe / box
trench.
2) Construction of all type inspection chambers.
3) Supply, laying, jointing, testing and commissioning of RCC NP-3 pipe/ precast RCC rectangular
drains with all section sizes as indicated in the layout plan of storm water drainage system.
4) Site would level in such a way that it is drained out properly.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 69
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All designs, materials, works and construction operations shall conform to the Standards and
Specifications given below and attached as an annexure.
Where the Contractor intends to use an alternative to these Standards/Guidelines for delivering an
equal or better product, he shall be permitted to use such alternative subject to the following
conditions:
He shall demonstrate that the proposed alternatives conform to any of the following international
Standards, Codes of Practice, Specifications, Guidelines, etc.
In case the Consultant intends to use any alternative material/technology/method, whether patented
or otherwise, that is not specifically covered in the Indian or International Standards as listed above,
but the use of which has been permitted on similar projects (similar in category of buildings) as
the Building Projects, he would be permitted, its use on certification by the owners of such similar
projects regarding the continued successful performance of such materials, technologies, methods,
procedures or processes for at-least 5 years of the service life of the project. Such a certification shall
be supported with details of critical performance parameters.
Such other reference standards published by the following that may be considered:
DIN Deutsche Industries Norman (German Standards)
AFNOR Association Francaise de Normalisation (French Standard Institute)
BSI British Standard Institute
ASTM American Society for Testing and Materials ANSI
American National Standards Institute
The above is the list of codes included for guidance and compliance with applicable portions only and
the omission of any from the list does not relieve the contractor from compliance therewith.
Latest version of the Codes, Standards, Specifications, etc., notified/published at least 60 days before the
last date of bid submission shall be considered applicable.
Where the Standards and Specifications for a work are not given, Good Industry Practice shall be
adopted to the satisfaction of the Employers Engineer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 70
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. Structural Works
1.1. Introduction
Aurangabad Integrated City (AURIC) has proposed to construct a AURIC Hall Building within a site area
of 2.77 acres at phase I of Shendra Bidkin Industrial area, Aurangabad. The building is classified as
Business and Office Buildings based upon the type of occupancy as per IS 875 (Part 2). This design basis
report will be used for the design of the AURIC Building and allied structures for AURIC.
This Design Basis Report is not applicable to the design of the exterior glass curtain wall.
The materials, detailed design and drawings shall conform to all relevant provisions of BIS (Bureau of
Indian Standards) codes and standards, and the NBC (National Building Code). If there is any variation
between the requirements of the BIS standards and NBC with the requirements stated in this DBR, then the
more conservative of the requirements shall be adopted. A list of some important codes and references to
be referred to in design are listed in Section 10 of this DBR. The list is not exhaustive list further
reference shall be added based on the design requirement during the detailed engineering stage.
The structure shall be analysed for different load cases such as dead loads, imposed loads, wind loads,
seismic loads, etc. as well as different load combinations amongst either of the above and shall be designed
for the maximum intensity to which the structure is expected to be exposed.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 71
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The footings for columns and shear walls will be sized based on this soil bearing capacity. The type of
foundation shall be open (isolated or combined) footings. The depth of foundation shall be up to hard strata
or 1.5m from natural ground level, whichever is more. All footings shall be located below the grade slab at
the lower ground level. For adjacent footings at different levels, clear horizontal distance between the
footings shall be at least twice the difference between the bottoms of footings. If required, plumb concrete
shall be used to raise the level of lower footing.
The location of the tie beams between the footings and the lower basement slab shall be determined as per
the following:
Tie beam shall be provided if the distance between top of footing and bottom of raft (unsupported length of
column) is more than 5.0m.
The soil type proposed to be used in analysis as per Table 1 of IS 1893 (Part 1): 2002 is Type II Medium
Soils.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 72
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Two ramps on either side of the building are proposed for access to the lower ground level parking. Ramp
slab on grade of required thickness shall be provided, surrounded by retaining walls. Cantilever retaining
walls will be provided around the lower ground level parking to retain the difference in level of the soil. In
addition to this, a surcharge loading of 10kN/m2 will be considered. The earth pressure coefficients for
estimating the lateral loads shall be the maximum of (a) 0.33 or (b) coefficient obtained from Coulombs
theory.
Member sizing and sectional properties assigned shall be dependent on the critical load case or the
combination subjected to the building with applicable factor of safety.
For the design of prestressing of the specific beams, the forces and proportioning of the prestressing
tendons will be corresponding to the vertical loads only. Additional reinforcement will be provided to these
beams in case they are a part of the lateral load resisting OMRF.
Design of water tanks shall be based on consideration of adequate resistance to cracking as well as
adequate strength, and shall be as per the requirements of IS 3370:2009.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 73
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All structural steel structures will be designed using the Limit State Method as per IS 800:2007 or Working
Stress Method as per IS 800:1984. Mild steel with minimum yield strength of 250 MPa will be considered
in design of structural steel components. Structural analysis shall be made within the permissible limits
conforming to IS 800:2007 or shall be in accordance to relevant IS codes.
1.6. Materials
1.6.1. Concrete
All RCC structures will be designed and detailed using the limit state method as per IS 456:2000. Mix
proportion of the grade of concrete as per the design requirement shall be considered as per Clause 6.1 IS
456:2000.
Sr. No. Parameters Minimum Grade of Concrete
1 Foundation M50
2 Sub Structure up to Plinth Level M50
3 Super Structure up to Terrace Level M50
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 74
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All external brick masonry shall be of 200 mm thick and internal brick masonry will be 115/150 mm thick
as per the detailed drawings.
The general external faade of the building will be made of perforated metal screen, which is located at a
distance of 0.9m from the face of the structural beam of the building. The screen will be attached to the
RCC members (beams or slabs) of the building the sizing and location of the screen attachments will be
as per the screen detailed design.
For design of the beams, load corresponding to 200 thick brick walls will be considered for walls and
faade.
All reinforced cement concrete members and walls shall be proportioned to achieve a minimum of 1.5hr
fire rating as per IS 1642 1989. Henceforth minimum thickness provided to the members shall abide the
requirement as per Clause 21 and Clause 26.4 of IS 456:2000
All structural steel members will be protected with paint (two coats of Synthetic Enamel of approved
colour and paint over one coat of Zinc Chromate primer). Any further fire protection for the structural steel
members will be adopted, if required, in consultation with the fire and safety consultant.
1.8. Corrosion
1.8.1. Corrosion in Reinforcement
The environmental exposure conditions, to which all RCC members will be exposed during its working life
is Very Severe for elements below plinth and Moderate for elements above plinth, as per clause 8.2.2.1
Table 3 of IS 456:2000. The design consideration includes use of durable concrete with Ordinary Portland
Cement (OPC) of appropriate Grade or Portland pozzolana cement as per Clause 5.1 of IS 456:2000.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 75
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Potable water shall be considered for mixing and curing of concrete with permissible limit of Suspended
Solids, Chloride and Sulphate content as per Table 1 of IS 456:2000.
The minimum cement content and maximum free water cement ratio shall conform to Table 5 of IS
456:2000.
In order to meet durability requirements, minimum nominal cover shall be determined depending upon the
type of exposure conditions as per Table 16 of IS 456:2000.
1.9 Deflection
Deflection in concrete structures shall be in general limited by adherence to the limits on span by depth
ratios for beams and slabs and length to lateral dimension ratios for columns as described in IS 456:2000 or
any other applicable relevant codes, provided the condition given in the code for applicability of the ratios
are satisfied. Otherwise, deflection calculations will be made to ensure that the deflections are within
permissible limits specified in IS 456:2000.
Deflection in structural steel members shall generally be limited to Table 6 of IS 800:2007, unless under
circumstances where a different value is more appropriate depending upon the nature of material and
intended use of member as per client requirement.
The deflection during earthquake shall conform to requirements of IS 1893 (Part 1): 2002.
1.10 Loads
1.10.1. Dead Loads (DL)
The dead loads of a structure include self-weight and weights of supported permanent loads like brick
walls, floor finishes, waterproofing, etc. These will be calculated based on the material and size of the
component.
The basic unit weights of these components, as per IS 875 (Part 1) are given below:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 76
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 77
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The following minimum loading will be considered based on the occupancy class:
No. Description of Room / Area Loading (kN/m2)
16. Office area with Light partitions (uniformly distributed load) 2.6
The loading diagrams of all floor levels for different types of load are available in section 11 of this
document.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 78
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The wind loads imposed on the structure will be based on a basic wind speed of 39 m/s as per IS 875 (Part
3).
The Wind Force F acting on to a particular face of the building is given by:
F = Cf A pz
Where,
pz = 0.6 Vz2
Vz = Vb k1 k2 k3
The coefficients are calculated corresponding to the Design Life of 50 years.
Here,
The site falls in seismic zone II, as per IS 1893 (Part 1) : 2002. Therefore, the seismic loads will be as
prescribed for that zone. Importance factor of 1.5 will be used.
The structure will be designed and detailed as per the requirements of IS 456; response reduction factor
(R) for earthquake resistant design will be 3.0, corresponding to Ordinary Moment Resisting Frames.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 79
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Earthquake loads will be calculated as per IS 1893:2002 (Zone II / 0.1; for Aurangabad).
The total design lateral force or design seismic base shear (VB) along any principal direction is given by:
V B A hW
Where Ah is design horizontal acceleration spectrum value as per Clause 6.4.2 of IS 1893 (Part 1): 2002,
using the fundamental natural period (Ta) in the considered direction of vibration
ZI S a Z
Ah max ,
2R g 2
Fundamental natural period of vibration (Ta) in the considered direction is given by:
0.09h
Ta (as per Clause 7.6.2 of IS 1893 (Part 1): 2002)
d
where, d is base dimension of building at plinth level in m along the considered direction, and h is the
height of the building
Separation between two adjacent units of the building shall conform to Clause 7.11.3 of IS 1893 (Part 1):
2002.
The city of Aurangabad is close to 45 oC line of the highest maximum temperature isopleths as per Fig.1
of IS 875 (Part 5) -1987 and 2.5 oC line of lowest minimum temperature isopleths as per Fig.2 of IS 875
(Part 5) -1987.
The maximum temperature ever recorded in the city was 46 oC on 25th May 1905 and minimum
temperature ever recorded in the city was 2 oC on 2nd Feb 1911. Thus, the maximum change in
temperature is about 42.5 oC. Adequate gaps at the expansion joints will be provided to accommodate the
movement of the adjacent structures due to temperature variation.
It is not required to consider any snow load, as there is no evidence of snow at the site.
Following minimum load combinations will be considered as per IS 875 (Part 5). Additional load
combinations may be considered as per the requirement of other relevant standards.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 80
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1 COMB 00 : 1.5 DL
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 81
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Here,
DL : Dead Load
The following are the referral codes implemented for Design Consideration:
IS:269 1989 Specification for Ordinary, rapid hardening and low heat Portland cement.
IS:383 1970 Specification for coarse and fine aggregates from natural sources for concrete.
IS:432 - 1982 Specification for Mild Steel and Medium Tensile Steel Bars and Hard Drawn Steel
Wire for Concrete Reinforcement.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 82
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS:816 1969 Code of Practice for Metal Arch Welding for General Construction in Mild Steel
IS:875 (Part 1) Code of Practice for Design Loads (other than Earthquake) for Buildings and
1994 Structures Part 1 Dead Loads Unit Weights of Building Materials and Stored
Materials
IS:875 (Part 2) Code of Practice for Design Loads (other than Earthquake) for Buildings and
1995 Structures Part 2 Imposed Loads
IS:875 (Part 3) Code of Practice for Design Loads (other than Earthquake) for Buildings and
1996 Structures Part 3 Wind Loads
IS:875 (Part 5) Code of Practice for Design Loads (other than Earthquake) for Buildings and
1997 Structures Part 5 Special Loads and Load Combinations.
IS:1566 1982 Specification for Hard drawn steel wire fabric for Concrete Reinforcement
IS:1641 1988 Code of Practice for Fire Safety of Buildings (General): General Principles of Fire
Grading and Classification.
IS:1642 1989 Code of Practice for Fire Safety of Buildings (General): Details of Construction.
IS:1786 2008 High Strength Deformed Steel Bars And Wires For Concrete Reinforcement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 83
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS:1893 2002 Criteria for Earthquake Resistant Design of Structures Part 1 General
IS:2062 2006 Hot Rolled Low, Medium and High Tensile Structural Steel
IS:3370 2009 Code of Practice For Concrete Structures For The Storage Of Liquids
IS:6006 1983 Specification for Uncoated stress relieved strand for Prestressed Concrete
IS:14268 Uncoated Stress Relieved low relaxation seven-ply strand for Pre stressed Concrete
1995 Specification
Conc. Soc.TR- Post Tension concrete design handbook (to be used in conjunction with the BS
043 8110)
ACI 318 Building code requirement for structural concrete & commentary
BS 4447 Specification for the performance of prestressing anchorages for post tensioned
construction
BS 4486 Specification for hot rolled and processed high tensile alloy steel bars for the
prestressing of concrete
BS 5896 Specification for high tensile steel wire and strand for the prestressing of concrete
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 84
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
BS EN 447 Grout for prestressing tendons Specification for common grout quality control.
Standards and Specifications for the Design and Construction of Electrical works are given in this section;
3.2 BACKGROUND
The contractor shall comply with all the minimum requirements of the Design and Construction of
Electrical works as per the Latest Standards, Statutory requirements, National Building codes and all other
relevant regulations
The system, design, materials, equipment, installation, testing and commissioning shall, in addition to all
other applicable codes and standards, comply with the latest requirements of the following standards,
codes, principles and specifications issued by Indian standards or IEC codes :-
1.1 SCOPE
This specification covers the requirements of supplying of HT OUTDOOR metal clad cubicle switch gear
having Vacuum Circuit Breakers. These are general requirements of switchgear panel.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 85
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The switch gear panel and components mounted shall confirm to the following latest revisions of relevant
Indian or equivalent British or International standards. In case of any conflict between the following
standards and this specification, the requirements of this specification shall prevail.
IS: 2516(Part1 sec.2) Specifications for circuit breakers. General & Definitions (for voltages
above 1000V A.C.).
IS: 2516(Part1 sec.3) Specifications for Alternating (circuit breakers requirements (voltage
above 33KV).
IS: 2516(Part 2 sec.2) Circuit breaker tests voltage (range 1 KV to 33 KV).
IS: 4710 Switches and switch isolators (above 1 KV but not exceeding 33 KV.)
IS: 375 Marking and arrangement of switch gear bus bars
IS: 2707 (Part 1 to 4) Current Transformers.
IS: 3156 Voltage Transformers.
IS: 1248 Electrical Indicating Instruments
IS: 3231 Electrical relays for power system protection.
IS: 6875h Control switches and push buttons
IS: 4483 Preferred panel cutout for relays
IS: 9046 HT Vacuum contactors
IS: 3427 Degree of protection provided for metal enclosed switchgear and control
gear.
IS: 5578 Guide for marking of insulated conductors.
IS: 5082 Material for data for Aluminum conductors
IS: 3618 Phosphate treatment of iron and steel for protection against corrosion
IS: 6005 Code of practice of phosphating of iron and steel
IS: 5 Painting.
IS: 722 Integrating meters
IS: 2544 Specifications for HV post insulators
1.2 CONSTRUCTION:
1.2.1 The switch gear panel shall be metal enclosed, rigid, free standing, floor mounted draw out,
dead front type and fabricated from standard prefabricated, cold rolled sheet steel units. The
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 86
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
vertical units shall be assembled in such a way that uniform height can be achieved while
line up of each vertical units on floor.
1.2.2 The minimum thickness of the sheet steel shall not be less than 2.5 mm. Necessary
stiffeners shall be provided.
1.2.3 The switchboard shall be totally enclosed, vermin -proof, except bus bar compartment.
Degree of protection of enclosure shall be minimum IP56 as per IS: 3427. If necessary,
openings for natural ventilation louvered with wire mesh shall be provided. For bus bar
compartment wire mesh shall be such as to protect against object of 1.0 mm size and above.
1.2.4 All doors, removable covers, gland plates and other openings shall be gasket all round the
perimeter with neoprene gaskets.
1.2.5 Switch gear shall be provided with an ISMC channel as a base frame. Minimum height of
the base frame shall be of 100 mm.
1.2.6 All doors shall be supported by strong hinges of concealed type and braced in such a
manner as to ensure freedom from sagging, bending and general distortion of panel or
hinged parts.
1.2.7 Switchboards shall be suitable for site conditions as specified in the Technical Data Sheet.
1.2.8 Each unit of the switch gear shall be provided with necessary internal sheet metal barrier to
form separate components for buses/Indicating instruments/protective relays/control and
power cable connection etc. Compartment for cable connection shall allow adequate space
for cable pulling, termination and connection work with energised switch gear. Suitable arc
propagation barrier shall also be provided. Preferably independent pressure release valves
shall be provided for different compartments. Terminal strips for outgoing control cable
connection should be accessible to facilitate working and testing with breaker in test/service
condition with the energised switchboard.
1.2.9 After isolation of the power and control connection of a circuit, it shall be possible to safely
carry out maintenance or a repair work in a compartment with the bus bars and adjacent
circuits alive.
1.2.10 At a future date, it shall be possible to extend the switch gear in either direction. Ends of the
bus bars shall be suitably drilled for this purpose. Panels at the extreme ends shall have
openings which shall be covered with plate screw to the panel with necessary gaskets.
1.2.11 Switch gear shall be vertical isolation and horizontal draw out type.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 87
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.2.12 All draw out circuit breaker trucks/trolley of the same rating for all outgoing breakers shall
be identically wired/equipped for complete inter-changeability at site. `Service', `Test',
`Draw Out' positions of the draw out carriage of the switchboard shall be provided.
Automatic safety shutters shall be provided to ensure the inaccessibility of all live parts
after the breaker is drawn out.
1.2.13 Dummy panels required for rear extensions for cable terminations or to mount the
components shall be included in the offer and details of each type of such panels shall be
furnished along with offer.
Necessary mechanical and electrical interlocks between H.T. and L.T. switch gears shall be
provided in closing and tripping circuits of breakers which shall be a part of the specification. The
total bill of material and scheme designed by the manufacturer will be subject to client/consultant's
approval and any addition or deletion shall be binding to the manufacturer on the basis of unit rates
available in the offer.
1.4 ACCESSIBILITY:
1.4.1 Checking and removal of components shall be possible without disturbing adjacent
components. All components shall be easily accessible. It shall be possible to set all
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 88
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
`measuring' and `protective' relays without de- energizing the switchboard. All mounted
equipment shall have painted identification labels at the front & rear also. In addition to that
identification numbers shall be painted on the panel wall to give permanent identification
mark. Mounting of the relays for a particular breaker panel shall be limited to that particular
panel.
1.4.2 Unused CT secondary terminals must be short circuited and wired to the terminal block. All
terminals shall be shrouded with plastic covers to prevent accidental contact.
1.5.1 The switchboard shall comprise 3 phase bus bars as indicated in the Technical Data Sheet
or SLD which shall extend through all units of the switch gear. All phase bus bars shall be
of uniform cross section throughout the switch gear and shall be sized to carry continuously
the current specified in the Technical Data Sheet or SLD. Bus bars shall be housed in a
separate air insulated chamber and shall be accessible for inspection only with special tools.
Wire guards/mesh shall be provided inside the sheet steel enclosure to allow visual
inspection of bus bars, CT's, PT's and cable terminations and to avoid accidental touch
when rear cover is removed.
1.5.2 Bus bars shall be made of electrolytic copper and shall be sleeved and joints shall be
shrouded. Fiber glass/metal sheet with cast resin bushing partitions shall be provided at
every junction between two adjacent cubicles. All bus bar joints shall be shrouded with
shrouds having sufficient insulation level suitable for nominal system voltage.
1.5.3 Bus bars shall be supported at regular intervals and both, bus bars and the supports shall be
adequately sized and braced to withstand the specified short circuit level without permanent
deformation. Dynamic stresses shall be calculated on the basis of the specified peak short
circuit currents. All bus supports shall be of non carbonizing material resistant to acids and
alkalis and shall have non hygroscopic characteristics such as SMC, DMC epoxy bonded
fiber glass.
1.5.4 Thermal design of the bus bars shall be based on installation of the switch gear in ventilated
conditions. The cooling air volume shall take into account only the bus enclosure.
1.5.5 The maximum operating temperature of the bus bars at the maximum design temperature
inside the panel shall be as per IS: 1272 and IEC 298
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 89
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.5.6 Bus bars shall be sleeved with colour coded type sleeve having insulation level suitable for
nominal system voltage. If the insulating sleeve is not coloured bus bar shall be colour
coded with coloured bands at suitable intervals.
1.5.7 All bus bars joint and bus tap joints shall be of the bolted type and shall be shrouded.
Spring washers shall be provided to ensure good contact at the joint locations and suitable
contact grease shall be applied just before making a joint.
1.5.8 Positive/live terminal or bus bar shall be located at the top or on the left for vertical and
horizontal layout respectively.
1.5.9 Sequence of Red, Yellow, Blue phases shall be left to right and top to bottom for horizontal
and vertical layout respectively.
1.6.1 The incoming and outgoing power cable connection shall be through PILC/XLPE/PVC
cables of various sizes as indicated in the Technical Data Sheet or SLD. Ample space for
connection for these cables shall be provided at the rear of the switchboard. In order to
avoid accidental contact in the cable compartment while carrying out inspection by opening
the back cover, a removable expanded metal barrier shall be provided in the cable
compartment.
1.6.2 The cable entry of the switchboard shall be from the bottom.
1.6.3 Cable lugs and the requisite bushes for sealing power cable entries shall be supplied along
with the switchboard.
1.6.4 `Cupal' washers shall be provided for copper busbar to aluminum cable terminations.
1.6.5 The switchboard shall be supplied complete with supports for clamping outgoing and
incoming cables. Terminal blocks shall not be used to support cables. The distance
available between cable gland plate and terminal lug shall not be less than 1000 mm for
switchgear upto 11 KV. cables.
1.6.6 In case, cable termination cannot be accommodated inside the panel, a suitable box for
mounting at the rear side and at the bottom of panel shall be supplied. Earth strip shall also
be brought to this box. In lieu of this a dummy panel may be provided.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 90
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.6.7 The individual switchgear panel shall have adequate space and terminal busbar clearance
for accommodating no. of cables as specified in Technical Data Sheet and SLD. The type of
cable termination units to be considered shall be heat shrinkable type.
1.7.1 Inside the cubicle the wiring for control, indication, signaling, protection and instrument
circuits shall be done with PVC insulated stranded conductors. The insulation grade shall
be 1.1 KV. The wiring shall preferably be enclosed in plastic channels or neatly bunched
together.
1.7.2 10% spare terminals shall be provided on each terminal block. Conductors shall be
terminated with adequately sized compression type copper lugs for connection to
equipment terminal block. All auxiliary equipments terminals shall be made with pressure
type terminals. Sufficient terminals shall be provided on each terminal block to ensure that
not more than one outgoing wire is connected per terminal. Terminal strips shall preferably
be separated from power circuits by metal barriers or enclosures. All spares contacts of aux.
relays, timers etc. shall be wired upto the terminals.
1.7.3 Each wire shall be identified at both the ends by, correctly sized PVC ferrules. Shorting
links shall be provided for all CT terminals.
1.7.4 For CT circuits 2.5 sq. mm copper conductor shall be used. Other control wiring can be
with 1.5 sq. mm copper conductors.
1.7.5 Control cables shall enter the switchgear from the bottom/ top. It shall be possible to have
the control cable entry from both the left and right side corners at the front portion of the
switchgear without cutting any standard part of for these cables are also included in the
scope of supply of the switchboard. The cable glands shall be compression type, supporting
facilities shall be provided for clamping the control cables. All control cables shall be with
2.5 sq. mm Cu stranded conductors.
1.7.6 All inter panel control wiring shall be done by the switchgear supplier. The inter panel
wiring shall be taken through PVC sleeves or suitable grommets. Multi pin plug shall be
provided and should have scraping earth terminal.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 91
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.7.7 Control cable cutout and gland plate shall be provided preferably at the place where the
power cable cutout will be provided. Gland plate for the control cables shall be separate
from those provided for the power cables.
Breaker tripping and closing devices shall be operated on D.C. supply. The rated D.C. voltage shall
be as specified in the Technical Data Sheet. The supply for breaker opening, closing and indication
devices shall be provided as under:
a) One D.C. feeder shall be provided for each bus section. The Bus coupler panel may be fed
from any of the two supplies.
b) One separate 240 V AC supply shall be provided for space heater etc.
Mechanical indication for breaker positions such as ON, OFF, spring charged, test position/Service
position shall be provided. Various Electrical indications with colours are indicated below shall be
provided.
1.9.1 Continuous earth bus-bar running throughout the length of the switchboard shall be
provided. All doors and movable parts shall be connected to the earth bus with flexible
copper connections. Provision shall be made to connect the earthing busbar to the plant
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 92
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
earthing grid at two ends. All non-current carrying metallic parts of the equipment shall be
earthed. Earth bus shall be brought back to cable compartment and earthing bolts shall be
provided to ground cable Armour. Mating surfaces of all bolted parts shall be specifically
zinc passivated to ensure continuity between them.
1.9.2 The material of the earth bus shall be copper. The earth bus size shall be minimum 180
mm2 copper upto short circuits withstand capacity of 31.5 KA and 300 mm2 above 31.5
KA.
1.9.3 All instruments, relays and other components shall be connected to earth busbar by means
of 650 V grade, PVC insulated, stranded tinned copper conductor of 2.5 sq.mm.
1.10.1 A nameplate with the switchgear designation at the top of the central panel and separate
nameplate giving feeder details shall be provided at front and rear side of each panel.
1.10.2 Name plates shall be provided for each equipment (Lamps, PBs, Switches, Relays,
Auxiliary contactors etc.) mounted on the switchboard. Special warning plates shall be
provided on all removable covers or doors giving access to high voltage cables, bus bars.
Special warning label shall be provided inside the switchboard also, wherever considered
necessary. Identification tags shall be provided inside the panels matching with those
shown on the circuit diagram.
1.10.3 Engraved nameplates shall preferably be of 3-ply (Red-white- red or Black-white-Black
lamicoid sheets or anodized aluminum or back engraved Perspex sheet nameplates shall be
provided. Engraving shall be done with square groove cutters. Hard paper nameplates will
not be acceptable. Name plates shall be fastened by Screws and not by adhesives.
1.11.1 All metal surfaces shall be thoroughly cleaned and digressed to remove mill scale, rust,
grease and dirt. Fabricated structure shall be pickled and then rinsed to remove any trace of
acid. The under surface shall be prepared by applying a coat of phosphate paint, and a coat
of yellow zinc chromates primer. The under surface shall be made free from all
imperfections before undertaking the finishing coat.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 93
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.11.2 After preparation of the under surface, the switchboard shall be spray painted with two
coats of final paint. Colour shade of final paint shall be smoke gray shade no. 631 as per IS:
5 unless otherwise specified. The finished panels shall be dried in stovings ovens in
dust-free atmosphere. Panel finish shall be free from imperfections like pinholes, orange
peels, runoff, paint etc. The supplier shall furnish painting procedure details along with the
offer.
1.11.3 All unpainted steel parts shall be cadmium plated or suitable treated to prevent rust
corrosion. If these parts are moving elements, then these shall be greased.
1.12.1 Each vertical cubical shall be provided with space heater to prevent moisture condensation
and maintain required temperature. The space heaters shall be located at the bottom of the
switchboard and shall be controlled through a thermostat with an adjustable setting with
single pole MCB with overload and short circuit release in the phase, link in the neutral.
The thermostat shall preferably be located in the metering/ relay chamber.
1.12.2 Space heater shall be of strip type rated for operation on a 240 V, single phase, 50 Hz., A.C.
supply system.
1.13.1 The switchboard shall be suitable to be installed on a base frame supplied in one piece
along with foundation bolts. These base channels shall be dispatched two months in ad-
vance from the date of dispatch of switchboard so that they can be buried and grouted in the
concrete floor. Ample dimensioned oblong holes shall be provided at the bottom of all the
switchboards for their installation of base frame. In addition, the switchboard shall have an
additional base channel at the bottom with smooth surface.
1.14 BREAKERS:
1.14.1 Vacuum circuit breaker shall be used in the switchboard. Exact type and rating shall be as
indicated in the Technical Data Sheet.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 94
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.14.2 10% spare VCB bottles of each rating shall be supplied along with the switchboard.
1.14.3 Vacuum circuit breaker shall be designed with low switching over voltage level and long
switching life. The interrupter shall be leak free with a target value of vacuum life as 25
years.
1.14.4 The breakers shall have at least 8 NO + 8 NC spare auxiliary contacts. If these are not
available an auxiliary contactor shall be used to multiply the auxiliary contacts of the
breakers. All auxiliary contacts shall be wired to the terminal block. Auxiliary contacts and
limit switches shall be in dust tight enclosures.
1.14.5 The breaker shall have motor operated spring charged mechanism. In addition to this, it
shall be possible to charge the springs manually, if required. In case the limit spring fails to
cut out the spring charging motor when the springs are fully charged the motor shall be
automatically decoupled and annunciation for this shall be provided. The control circuit
shall be suitable for local as well as remote control. Breaker shall trip free and shall have an
anti-pumping device. Breaker operating duty shall be 0-3'-CO-3'-CO except for switchgear
line up having motor feeders stage wise, receleration feature in which case the duty shall be
0-0.3"- CO-3'-CO. Whenever a PT is mounted on the breaker carriage all auxiliary wiring
shall be done in PVC flexible conduits.
1.14.6 Adequate provision shall be made in Vacuum circuit breaker for motor switching to limit
the over voltage.
1.14.7 Mechanical trip push buttons shall be provided for all the breakers. Mechanical closing
device will not be acceptable for motor feeders. Complete motor assembly should have
interchangeability with identical rating of the breaker. Each motor breaker feeder shall be
provided with an operation counter.
1.14.8 All integral earthing system or separate earthing carriage be provided. After withdrawing
the circuit breaker, this can be inserted to facilitate earthing of the cables. Unit rate in the
panel shall be furnished.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 95
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Technical Data Sheet or SLD. For general guidance, the protective current transformers
shall have an accuracy class `5P' and an accuracy limit factor greater than `10'. Low
reactance C.T.s shall be used for protection. Current transformers for instruments shall have
an accuracy class 0.5 and an accuracy limit factor less than 5.0. If a metering load is fed
from a protection C.T., suitable 1/1 or 5/5 ratio interposing C.T.s shall be used.
a. The voltage transformers shall be cast resin and draw out type and provided with primary
and secondary fuses.
b. The draw-out mechanism shall disconnect the bus bars and V.T. primary and secondary
terminals shall be earthed. The primary connection shall be disconnected before the V.T. or
its primary fuses become accessible.
c. The voltage transformers shall have an accuracy class 1.0 from 10% to 120% of normal
voltage.
d. Secondary and tertiary windings of voltage transformer shall be rated for a three phase line
to line voltage of 110 V except as noted.
All measuring and recording instruments shall be of square pattern 144 mm x 144 mm flush
mounted type. Instruments shall be provided wherever specified in the Technical Data Sheet or
SLD. All auxiliary equipment such as shunts, transducers C.T.s, V.T.s that are required shall be
included in the supply of switchboard.
The KW meter shall be suitable to measure unbalanced loads on a 3 phase 3 wire system. The KW
and the voltmeter shall operate of a V.T. secondary of 110 volts.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 96
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
These shall be direct reading or digital type square pattern 144 mm x 144 mm size, suitable for
flush mounting and shall operate off a V.T. secondary voltage of 110 volts. The standard range
shall be 45-50-55 Hz.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 97
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All tripping relays shall be lockout type with hand reset contacts and shall be suitable to operate off
the specified d.c. voltage. These relays shall have self coil cut - off contacts and shall be provided
with hand reset operation indicators. Tripping relays will be acceptable in non draw-out cases. The
number of contacts shall be as shown on the approved schematic drawings.
All measuring relays shall have `built in' flags to indicate relay operation. It shall be possible to
reset the flag without opening the relay case. Anti fungus treatment shall be provided for all relays.
Red push buttons shall be on the left side and green push buttons on the right side. Push button
ratings shall be 5A at 240 V AC or 2A at 110 V DC (inductive load). Emergency stop push buttons
shall be lockable in the operated position.
The key shall be released from the push button in both `Released' and `Operated' positions and
operation of the push button shall be possible in the key release position. Push button knobs for
emergency stop push buttons shall be released to prevent accidental operation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 98
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.18 DRAWINGS:
The manufacturer shall develop his own general arrangement and schematic drawing adding
necessary auxiliary devices, accessories, components particular to supplied equipment, etc. which
are required for safe, convenient, efficient and proper operation of the HT switchgear.
Manufacturer shall submit for owner/consultant's approval the single line diagrams, general
arrangement drawings, flooring and mounting detail drawings and schematic diagrams.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 99
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Once manufacturer's schematic diagrams have been finally approved by owner/consultant, the
manufacturer shall prepare wiring connection diagrams for each cubicle. These diagrams shall
show any wiring inside the cubicle starting from the cubicle terminal strips. These diagrams shall
be used by the owner for troubleshooting and shall show any device, terminal and wire number.
The manufacturer shall submit all the drawings in four copies for owner/consultant's approval.
Manufacturer shall submit four prints and reproducible of schematic, GA and wiring diagrams in
final.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 100
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 101
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 102
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 103
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 104
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 105
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 106
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 107
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.3 RATING
The rating, voltage ratio, vector group and type of cooling of transformer, tap changing gear shall
be as specified in the enclosed data sheet.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 108
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
B Core:
a) The design of the magnetic circuit shall be such as to avoid static discharge, development of
short circuit paths within itself or to the earthed clamping structure and the production of
flux component at right angles to the plane of the lamination, which may cause local
heating.
b) The magnetic circuit shall be of core type construction. It shall be built out of high grade,
non-ageing, low losses, high permeability, cold rolled grain oriented silicon steel
lamination.
c) The finally assembled core shall be free from distortion. It shall be rigidly clamped to
ensure adequate mechanical strength and to prevent vibrations during operation.
d) The core shall be provided with lugs suitable for lifting the complete core and coil
assembly.
e) All parts of the cores shall be of robust design capable of withstanding any shocks to which
they may be subjected during lifting, transport, installation and service.
C Internal Earthing:
All metal parts of transformer with the exception of the individual core lamination, core
bolts, and associated individual clamping plates shall be earthed.
D WINDING
a) Winding shall be subjected to shrinking and seasoning process, so that no further
shrinkage occur during service. Adjustable devices shall be provided for taking up
possible shrinkage in service.
b) Materials used in the insulation and assembly of the winding shall be insoluble, non
catalytic and chemically inactive in hot transformer oil, and shell not often or be
otherwise affected under the operating conditions.
c) Neutral of all star connected winding shall be brought out in open.
d) The winding shall be designed to reduce a minimum out of balance forces in the
transformer at all voltage ratios.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 109
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
E TANK
a) Tank shall be made from good commercial grade low carbon steel and shall be of
welded construction.
b) Tank shall be designed to permit lifting, by crane of jacks, of the complete transformer
assembly filled with oil. Radiators shall be detachable type connected to the tank
through butterfly valves.
c) The material used for gasket shall be cork neoprene or approved equivalent.
d) Tank shall be provided with lifting lugs a minimum of four jacking lugs and suitable
haulage holes.
e) The tank cover shall be fitted with pockets for a thermometer and for the bulbs of oil
and winding temperature indicators. Protection shall be provided, where necessary, for
each capillary tube.
f) All wheels should be detachable and shall be made of cast iron or steel as required.
g) Inspection cover on the top shall be provided (for small transformer of 500 KVA and
above). Tank cover shall be suitably sloped to prevent accumulation of rainwater.
F Conservator:
a) A conservator complete with sump and drain valve to meet the requirement of expansion of
the total cold oil volume in the transformer and cooling equipment from the minimum
ambient temp. to 90C.
b) Normally one coil gauge magnetic\ prismatic\ plain type as specified shall be provided.
c) Conservator shall be fitted with a silica gel breather.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 110
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
c) If a diaphragm is used it shall be of suitable design and material and situated above
maximum oil level.
d) An equalizer pipes shall be connected between the pressure relief devices to the conservator
or silica gel breather shall be fitted to pressure relief device for relieving or equalizing the
pressure.
1.6 OIL
a) Transformer shall be supplied with first filling oil conforming to IS: 335.
b) Additional oil shall be supplied in non-returnable drums for each transformer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 111
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
c) Non-magnetic cable gland plate shall be provided in the cable box, whenever single core
cables are specified.
a) Oil temp. Indicator with/without electrical contacts shall be provided as specified in data
sheet.
b) Winding temp. Indicator shall be provided, if specified with no of contact required.
c) The tripping contact of winding temperature indicators shall be adjustable to close between
60C and 120C and alarm contacts to close between 50C and 100C and both shall
reopen when the temperature falls by about 10C.
d) Connections shall be brought from the device to marshaling box.
a) A double float type Buchholz relay as per IS:3637 shall be provided. Two electrically
independent alarm and trip contact shall be provided. Two isolating valves shall be
provided an either side of the relay. Buchholz relay shall be provided with a test cover.
1.11 PAINTING
a) The interior of transformer tank, other oil filled chambers and internal structural steel work
shall be painted with heat resistant, oil insoluble insulating varnish after thorough cleaning
of all scales and dust by shot blasting or other approved method.
b) Steel surfaces exposed to the weather shall be thoroughly cleaned and applied first coat of
zinc chromate, second coat of oil and weather resistant paint and final coat of glossy oil and
weather resistant non fading paint of shade no 632 of IS :5 (epoxy paint)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 112
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3.3 Efficiency at
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 113
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 114
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Any other information, if not specified above, but necessary for the evaluation of offer shall be
furnished by the supplier.
Whether called for specifically or not, all accessories required for normal operation of equipment
are deemed to be considered as a part of the contractors scope of supply. Hardware / fabricated
supports required for mounting and installation of the panels is within the scope of work.
It is not the intent to specify completely herein, all details of design and construction of the
equipment. However, the equipment shall conform in all respects to high standard of Engineering,
design and workmanship and be capable of performing in continuous commercial operation up to
the Manufacturers guarantees in a manner acceptable to the Engineer, who will interpret the
meaning of the drawings and specifications and shall be entitled to reject any work or material
which is not full accordance therewith.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 115
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All the Panels shall be metal clad, totally enclosed, rigid, floor mounted, air - insulated, cubical type
suitable for operation on three phase / single phase, 415 / 230 volts, 50 Hz.
The panels shall be designed for minimum expected ambient temperature of 45 degrees Celsius, 80 percent
humidity and dusty weather.
Should conform to Indian Electricity Act and rules (till last amendment) & approved as per FIA norms.
Applicable IS Standards
Meters (measuring) for analog meters IS:1248-1958
Installation and maintenance of switch gears IS:3072-1975
H.d. Air breaker, switch gears and fuses for voltage not exceeding 1000
IS:4047-1977
volts
Selection, installation and maintenance of fuses up to 650 volts IS:8106-1966
General requirements for switch gear and gear for voltage not exceeding
IS:4237-1967
1000 volts
IS:2147-1962
IS:8130
Flexible cords
Shunt capacitors for power systems IS:2834-1954
Hrc cartridge fuses and links up to 660 volts IS:2208
Hrc fuses having rupturing capacity of 50 ka IS:9224
Ac electricity meters: part 1 general requirements
IS:772 PART 1
And tests
Direct acting electrical indicating instruments IS:1248
Current transformers IS:2705
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 116
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.1 Construction :
Switchboard connection
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 117
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All connection and tap offs shall be through adequately sized connectors appropriate for fault level at
location. This shall include tap off to feeders and instrument/control transformers.
For unit ratings upto & including 63 amps, PVC insulated copper conductor wires of adequate size to carry
full load current shall be used. The terminations of such interconnections shall be crimped. Solid
connections (busbars) shall be used for all rating above 63A.
All connections, tapings, clamping, shall be made in an approved manner to ensure minimum contact
resistance. All connections shall be firmly bolted and clamp with even tension. Before assembly joint
surfaces shall be filed or finished to remove burrs, dents and oxides and silvered to maintain good continuity
at all joints. All screws, bolts, washers shall be zinc plated. Only 8.8 grade nuts and bolts shall be used for
busbar connections.
All nut bolts for busbar shall be high tensile cadmium plated with 2 plain washers and 1 spring washer.
Hardware should be provided at cable termination end.
The low-voltage electrical switchboards shall be made up of identified functional volumes including the
busbar compartment, switchgear and control gear component compartment, connection compartment and
auxiliaries compartment.
The different busbars shall be the main busbars, distribution busbars and auxiliary busbars.
The busbars shall be made of electrolytic Al. with current density of 0.8A/Sqmm.
The compartments shall be located inside a metal enclosure with walls providing protection against direct
contact with live parts and guaranteeing a degree of protection IP 2X. The frame, the external panels (doors,
side and rear panels, tops) and internal elements (ducts) shall be made of 2 mm thick steel sheet metal and
protected by an epoxy-paint coating.
The max height of panel shall be 2375mm including the base channel of 75 x 40 mm ISMC coloured black.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 118
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Sheet metal elements in the immediate proximity of high current flow generating potential eddy current shall
be made of aluminium.
Drawers or air circuit breakers shall have four different positions: connected, test, disconnected and
removed. With drawability of upstream and downstream power circuits and of auxiliary circuits shall be
total, i.e. in compliance with standard IS 8326.
The construction system shall provide a complete set of elements for installing fixed or with drawable
switching and protective devices, measurement devices and control / monitoring devices in the switchboard.
The drawers shall be designed such that the rated degree of protection (IP, as per IS 2147: 1962) is
maintained whatever their position (connected, test, disconnected, removed).
Switchboard Compartmentalization
For compartmentalized switchboards, separate totally enclosed compartments shall be provided for
horizontal busbars, vertical busbars, ACBs, MCCBs, and cable alleys.
Sheet steel hinged lockable doors for each separate compartment shall be provided and duly interlocked with
the breaker in "ON" and "OFF" position.
For all Circuit Breakers separate and adequate compartments shall be provided for accommodating
instruments, indicating lamps, control contactors and control MCB etc. These shall be accessible for testing
and maintenance without any danger of accidental contact with live parts of the circuit breaker, busbars and
connections. Panel should be single front operated and cable Entry should be at TOP. Busbar and cable allay
access should be from front only.
LDB/PDB should be with double door arrangement. Acrylic cover to be considered on front hinged door.
Inside cover should be fixed plate type with MCB cutout features.
Each switchgear cubicles shall be fitted with label in front and back identifying the circuit, switchgear type,
rating and duty. All operating device shall be located in front of switchgear only.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 119
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
A horizontal wire way with screwed cover shall be provided at the top to take interconnecting control wiring
between vertical sections.
Separate cable compartments running the height of the switchboard in the case of front access boards shall
be provided for incoming and outgoing cables. Outgoing all control and power terminals should be KUT
type.
Cable compartments shall be of adequate size for easy termination of all incoming and outgoing cables
entering from bottom or top. The construction shall include necessary and adequate and proper support shall
be provided in cable compartments to support and clamping the cable in the cable alley / cable chamber.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 120
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Vendor shall provide dimensions of MCC. Final GA layout will be approved by TPL.
The bus bars shall be supported on non-breakable, non-hygroscopic epoxy resin or glass fibre reinforced
polymer insulated supports able to withstand operating temperature of 110C at regular intervals, to
withstand the forces arising from a fault level as stipulated in schedule of quantities. The material and the
spacing of the bus bar supports should be same as per the type tested assembly.
The minimum clearances to be maintained for enclosed indoor air insulated bus bars for medium voltage
applications shall be as per IS guidelines. The bus bar shall be as per current density of 0.8 A/Sq.mm Cross
Section area.
The bus bar shall be housed in separate compartment and shall be isolated with 3 mm thick FRC sheet to
avoid any accidental contact. The bus bar shall be arranged such that min. clearances between the bus bars
are as mentioned below:
The bus bar and interconnection shall be insulated with heat shrinkable PVC sleeves and shall be colour
coded in Red / Yellow / Blue / Black / Green to identify the three phases / neutral and earth of the system .
The bus bar shall be supported on unbreakable, non-hygroscopic DMC insulated supports (no bakelite
material should be used in panel) at sufficiently close intervals to prevent bus bar sag and shall effectively
withstand electromagnetic stresses in the event of short circuit capacity of 65KA RMS symmetrical fault for
1 sec and peak short circuit withstand of 105KA minimum.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 121
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All bus bar connections shall be done by drilling holes at factory in bus bars and connecting by
chromium plated bolts and nuts. Additional cross section of bus bar shall be provided in all panels to cover
up for the holes in the bus bars. Spring and flat washers shall be used for tightening of bolts.
All Cu/Al joints (if any) shall be connected with bi-metal sheet.
Instruments and indicating lamps shall not be mounted on the Circuit Breaker Compartment (in case
of ACB) door for which a separate and adequate compartment shall be provided and the
instrumentation shall be accessible for testing and maintenance without danger of accidental contact
with live parts of the Switchboard.
For MCCBs, instruments and indicating lamps can be provided on the compartment doors.
The current transformers for metering and for protection shall be mounted on the solid copper bus
bars with proper supports.
On all the incomers of switch boards ON/OFF indicators lamps shall be provided suitable for
operation on AC 230 volts supply. All lamps shall be protected with proper protection device.
Where phase indicator lamps are to be provided, these shall be associated with necessary ON/OFF
toggle switch. All the lamps shall have testing facility.
For instruments control MCB shall be used (Fuse with link not accepted)
2.4 Wiring
All wiring for relays and meters shall be with PVC insulated copper conductor wires. The wiring
shall be coded and labelled with approved ferrules for identification. The minimum size of copper
conductor control wires shall be 1.5 sq. mm. Runs of wires shall be neatly bunched and suitably
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 122
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
supported and clamped. Means shall be provided for easy identification of wires. Identification
ferrules shall used at both end of wires. All control wires meant for external connections are to be
brought out on a terminal board. The cables shall be suitable for withstanding 105 deg C.
2.7 Earthing
Continuous earth bus sized for prospective fault current to be provided with arrangement for connecting to
station earth at two points. Hinged doors / frames to be connected to earth through adequately sized flexible
braids. Calculations shall be provided for the earthing strip size as per the fault level of the panel. Min size
of earth bus shall be 50 x 6 mm Al.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 123
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Identification labels of Aluminium with black base and silver fonts shall be provided on all feeders / lamps /
panel name plate / relays / contactors etc. These shall indicate the feeder number and feeder designation also
along with rating of the switchgear. Sample for the same shall be first approved by engineer.
2.10 Installation
Splices shall be implemented to ensure the electrical continuity of the horizontal bus bars, auxiliary buses
and the protective conductor between adjacent sections.
It shall be possible to secure the sections to a floor that is flat (max variation within 2 mm/m:)
by anchoring directly to a concrete floor using anchor bolts;
by securing to ordinary metal profiles.
Extensions to the low-voltage electrical switchboards shall be possible on either side (right or left).
Optionally, the safety of persons shall be enhanced by a version complying with the requirements of
standard IEC 61641 concerning the propagation of an arc inside electrical switchboards. Test certificates
shall be available.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 124
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Provisions must be made, around the equipment critical zones, for visual/infrared inspection during
equipment operation, with respect to operator safety.
Earthed metal or insulated shutters shall be provided between drawout and fixed portion of the switchgear
such that no lives parts are accessible with equipment drawn out. Degree of protection within compartments
shall be at least IP 2X.
IP rating for all PCCS/MCCB in wet area like pump room shall be IP-65. (to be confirmed with engineer
before quoting)
All part of the panels carrying current including the components, connections, joints and instruments shall
be capable of carrying their specified rated current continuously, without temperature rise exceeding the
acceptable values of the relevant specifications at any part of the panels.
All units of the same rating and specifications shall be fully interchangeable.
2.13 L. T. Switchgears:
2.13.1 General:
The type, size, and rating of the components shall be as indicated on the relevant single line diagrams.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 125
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The circuit breaker dollies shall be of trip free pattern to prevent closing the breaker on a faulty current.
The MCB / MPCBs contact shall be silver nickel and silver graphite alloy and tip coated with silver. Proper
arc chutes shall be provided to quench the arc immediately. MCB's / MPCBs shall be provided with
magnetic fluid plunger relay for over current and short circuit protection. The over load or short circuit
devices shall have a common trip bar in the case of DP and TPN miniature circuit breakers. All the MCB's /
MPCBs shall be tested and certified as per Indian Standard, prior to Installation.
MPCB with extended support should be consider along with front operating mechanism. MPCB should be
with all accessories like; auxiliary contacts, door rotary mechanism etc.
The RCCB should suffices all the requirements of IS as per code IS - 12640 - 1988. The RCA should be
current operated and not on line voltage.
It should conform to all national and international standards like IS: 8828-1993, IS: 12640-1988, BS 4293 -
1983, CEE 27 (International commission Rules for the approved of electrical equipment).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 126
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.13.3 Fuse:
Fuses shall be of high rupturing capacity (HRC) fuse links and shall be in accordance with IS : 2000-1962
and having rupturing capacity of not less than 35 MVA at 415 Volts.
Disconnecting devices of approved type shall be provided to facilitate the removal of the circuit breakers
from the housing for test and maintenance purpose.
The ACB's shall have an arc-quenching device on each pole. The ACB's shall have auxiliary contacts for
signalling, interlocking etc. The ACB's shall have slow close facilities for checking contact operation and
contact gap adjustment.
All contacts subject to arcing shall be tipped with arc resisting material. Main contacts shall be silver plated,
multi-finger and spring-loaded type. Facilities shall be provided to isolate the circuit breaker for inspection
purpose.
Prevent the breaker from being isolated unless it is in the "OFF" position.
Prevent the breaker from being racked in to the service position unless it is in the "OFF" position.
Prevent the breaker from being accidentally pulled completely "OFF" the guide rail. Safety shutters of
insulating material shall be provided to prevent access to all live contacts, when the breaker is in the
inspection position or completely withdrawn.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 127
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Air circuit breaker shall be capable of clearing the maximum fault current, which can occur.
The breaker plates shall have an ON-OFF indicator, spring charge indicators, provision to padlock manual
handle and provision to lock draw-out mechanism. Electrically operated breaker shall have provision for
emergency manual closing by inserting a tool through the fuse plate. A control isolating switch shall be
provided on the fuse plate to isolated the supply to the charging motor.
The breaker shall be having feature such as to indicate voltage status / trip / fault alarm indicators / remote
operation from BMS ON/OFF, shunt trip release and motorised reclosing / contacts for remote indication
of open / close / trip wired to BMS, communication modules providing LAN interface with BMS and draw
out pattern with test facility provision.
All ACB releases shall be with long time + short time + instantaneous + earth fault selective protection.
MCCBs shall be designed according to Eco-design complying with ISO 14062 Especially MCCBs
materials shall be of halogen free type. They shall be supplied in recyclable packing complying with
European Directives.
The manufacturer shall implement nonpolluting production processes that do not make use of
chlorofluorocarbons, chlorinated hydrocarbons, ink for cardboard markings, etc
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 128
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
MCCBs shall be mounted in panel as fixed type versions in 3-pole and 4-pole versions. A safety trip shall
provide advanced opening to prevent connection and disconnection of a closed circuit breaker
MCCBs shall be designed for both vertical and horizontal mounting, without any adverse effect on electrical
performance. It shall be possible to supply power either from the upstream or downstream side
MCCBs shall provide class II insulation between the front and internal power circuits.
All poles shall operate simultaneously for circuit breaker opening, closing and tripping.
MCCBs shall be actuated by a toggle or handle that clearly indicates the three positions: ON, OFF and
TRIPPED.
MCCBs shall be able to receive a device for locking in the isolated position, with up to 3 padlocks, 8
maximum.
MCCBs shall be equipped with a push to trip button in front to test operation and the opening of the poles.
MCCB rating, push to trip button, performances and contact position indication must be clearly visible
and accessible from the front, through the front panel or the door of the switchboard.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 129
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
These characteristics will allow high cascading performance with moulded-case or miniature circuit-
breakers downstream
MCCBs shall be equipped with a tripping unit independent of the thermo-magnet or electronic one. This unit
will trip the circuit-breaker for high value short-circuits currents. The breaking will be carried out in less
than 10ms for short-circuit currents above 25In.
MCCBs shall comprise a device, designed to trip the circuit-breaker in the event of high-value short-circuit
currents. This device shall be independent of the thermal-magnetic or electronic trip unit.
MCCBs, the current ratings of which are identical with the ratings of their trip units, shall ensure
discrimination for any fault current up to at least 35 kA rms, with any downstream circuit-breaker having a
current rating less or equal to 0.4 times that of the upstream circuit-breaker.
MCCBs shall be equipped with a self-test of the connection between the electronic trip unit, the current
transformers and the actuator, that will not cause the circuit-breaker to trip. The self-test will be of positive
logic and visible through the flashing of a green LED in case the self-test occurred correctly and the
extinction of the LED in case the self-test failed.
The MCCB shall trip in case the environmental conditions of the circuit-breaker get out of their specified
range. However, it will be possible to overrule this feature.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 130
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Following tripping due to electrical faults (overload, short-circuit, earth fault if mentioned in SLD), remote
reset shall be inhibited.
The addition of a motor mechanism or a rotary handle shall in no way affect circuit breaker characteristics:
- Only three stable tripping mechanism positions (ON, OFF and TRIPPED) shall be
possible with the motor mechanism,
- Suitability for isolation shall be provided by positive contact indication (ON and OFF) in
front of the motor mechanism module
MCCBs shall be designed to enable safe on-site installation of auxiliaries such as voltage releases (shunt and
under voltage releases) and indication switches as follows:
- They shall be separated from power circuits,
- All electrical auxiliaries shall be of the snap-in type and fitted with terminal blocks,
- All auxiliaries shall be common for the entire range,
- Auxiliary function and terminals shall be permanently engraved on the case of the circuit
breaker and the auxiliary itself,
- The addition of auxiliaries shall not increase the volume of the circuit breaker.
- MCCB should be with all accessories like; spreads links, shrouding terminals, auxiliary
contacts, phase barrier, door rotary mechanism etc. Spreader links should be copper with
Ni-Cr plated
- Outgoing terminal of MCCB should be 3Ph+N+E.
The addition of a motor mechanism module or a rotary handle, etc., shall not mask or block device settings
It shall be possible to assemble earth fault protection moulded-case circuit breakers by adding a residual
current device (RCD) directly to the circuit breaker case. The resulting device shall:
- comply with IS 13947: 1993 standard,
- be immunised against nuisance tripping,
- be capable of working normally down to -25 C ambient temperature,
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 131
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
- operate without an auxiliary power supply, i.e. it shall be capable of operating normally
on any 2-phase or 3-phase power network with a voltage between 200 V and 440 V, and
of tripping the circuit-breaker even in the event of voltage dips down to 80 V
It shall be possible to equip MCCBs with devices indicating faults without tripping the circuit breaker.
Electronic trip units shall comply with IS 13947: 1993 standard (measurement of rms current values,
electromagnetic compatibility, etc.)
The trip units shall not augment overall circuit breaker volume
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 132
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
- Instantaneous protection
The threshold shall be either adjustable or fixed (starting from 1.5 times In and up to a value between 11 and
15 times In, depending on the rating)
Thermal Memory
In the event of repeated overloads, the electronic trip unit shall optimise protection of cables and
downstream devices by memorising temperature variations.
Options:
It shall be possible to install all options for the electronic trip unit:
- High-threshold earth-fault protection,
- Auxiliary contact to indicate the cause of tripping (long time, short time, instantaneous,
earth fault if requested),
- Data transmission via a BUS, in particular all the trip unit settings, current measurements
for each phase, tripping causes, circuit breaker status.
transmission, in particular all the trip unit settings, all electrical parameters (current, energy, THD, voltage,
etc.) measurements for each phase, tripping causes, circuit breaker status, control and alarms.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 133
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Software that allows these data to be analysed on PC shall be provided by the manufacturer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 134
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.13.6.19 Following control signal exchange between OCS / PLC & MCC panel shall be
considered for AHU panel & package systems in process mcc
From MCC panel to DES / PLC
- On, off & trip feedback separate continuous potential free contacts.
- For VFD feeders 42oma speed (rpm) feedback.
- Potential free contact for remote selection.
From DES / PLC to MOE panel
- Start & stop command single latched contact.
- For VFD feeders only 42oma reference current for speed control.
- Start permissive in local & remote mode.
2.13.6.20 Following control signal exchange between push button station & mcc panel shall be
considered.
a. On, off & trip feedback separate continuous potential free contacts.
b. Start & stop command seperate continuous potential free contacts.
2.13.6.21 Control philosophy
a. Under local mode selection start command will be executed from push button
station near motor.
b. Under remote mode selection start command will be executed from PLC panel.
c. Stop command can be executed without selection.
2.13.6.22 Motor feeder shall have motor protection circuit breaker (MPCB) with S/C and O/C
release.
2.13.6.23 Heavy duty bmr to be provided for blowers & fan application.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 135
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Parameters to be monitored shall be Frequency, Line to line and average and line to neutral and average
voltage, phase wise and average current, phase wise and total KVA, KW and P.F. reading and KWH
monitoring.
User programmable facility for delta 2e and star 3e measurement, C.T. and P.T. ratios, sliding window auto
sync. And auto scrolling of parameters shall be available.
Sensing shall be 3 phase, 4 wire measuring True RMS with voltage input range of 110 to 415 V nominal and
current input of 5 amps or 1 amps as per field configuration. Current range shall be from 50 mA to 7.5 A
and burden on PT or CT shall be app 0.2 VA.
Accuracy for kW / kWh shall be as per IS 1377 / CBIP88 and for all other parameters shall be +/- 0.5% of
full scale + 0.5% of reading + 1 digit. Digital readout shall be of 3 rows of 4 digits each (12.5 mm size) with
7 segments bright red LED. Input frequency shall be 50Hz / 60Hz +/- 5%. Power factor range shall be 0.5
lag unit 0.8 lead.
Resolution for power parameters shall be for 4 digits and energy parameters shall be 8 digits. Display update
shall be at every 15 seconds for demand parameters and 1 sec for other parameters. Display sequence shall
be parameter followed by value. Temperature range shall be 0-50oC and humidity <95% non-condensing.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 136
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Separate CT for each protection devices and instrumentation device shall be provided.
The CT shall be able to withstand max short time withstands current indicated for the assembly.
The CT shall be cast resin type.
Test links at secondary to facilities testing of instruments / meters and protection device.
Indicating Lamp shall be LED type and shall supplied complete with translucent covers to diffuse the lamp
light. Indicating lamps shall be part of push buttons where ever both are required and shall have testing
facilities. Protection in form of MCB / HRC fuse shall be provided for the lamps.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 137
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
This specification covers performance, design, material, construction, manufacture, inspection, testing,
packing forwarding, delivery at site, testing and commissioning of microprocessor controlled Auto transfer
switches with double throw power transfer switch mechanism as per single line diagrams, with all
accessories complete in all respects as described in this specification.
Whether called for specifically or not, all accessories required for normal operation of equipment are
deemed to be considered as a part of the contractors scope of supply. Hardware / fabricated supports
required for mounting and installation of the ATS is within the scope of work.
It is not the intent to specify completely herein, all details of design and construction of the equipment.
However, the equipment shall conform in all respects to high standard of Engineering, design and
workmanship and be capable of performing in continuous commercial operation up to the Manufacturers
guarantees in a manner acceptable to the Engineer, who will interpret the meaning of the drawings and
specifications and shall be entitled to reject any work or material which is not full accordance therewith.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 138
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IEEE Standard 446 - IEEE Recommended Practice for Emergency and Standby Power Systems for
Commercial and Industrial Applications
1.2 Products
1.2.1 Mechanically Held Transfer Switch
The transfer switch shall be electrically operated and mechanically held. The electrical operator shall be a
momentarily energized, single-solenoid mechanism. Main operators which include overcurrent disconnect
devices, linear motors or gears shall not be acceptable. The switch shall be mechanically interlocked to
ensure only two possible positions, normal or emergency. The switch shall be rated for AC-33A duty cycle
for mixed load application as mentioned in IEC 60947-6-1.
All transfer switch sizes shall use only one type of main operator for ease of maintenance and commodity of
parts.
The switch shall be positively locked and unaffected by momentary outages, so that contact pressure is
maintained at a constant value and contact temperature rise is minimized for maximum reliability and
operating life.
All main contacts shall be silver composition. Switches rated 600 amperes and above shall have segmented,
blow-on construction for high withstand and close-on capability and be protected by separate arcing
contacts.
Inspection of all contacts shall be possible from the front of the switch without disassembly of operating
linkages and without disconnection of power conductors. Switches rated 600 amps and higher shall have
front removable and replaceable contacts. All stationary and moveable contacts shall be replaceable without
removing power conductors and/or bus bars.
Designs utilizing components of moulded-case circuit breakers, contactors, or parts thereof, which are not
intended for continuous duty, repetitive switching or transfer between two active power sources are not
acceptable.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 139
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Where neutral conductors must be switched as shown on the plans, the AS shall be provided with fully rated
complete overlapping neutral transfer contacts. The neutrals of the normal and emergency power sources
shall be connected together only during the transfer and retransfer operation and remain connected together
until power source contacts close on the source to which the transfer is being made. The overlapping neutral
contacts shall not overlap for a period greater than 100 milliseconds. Neutral switching contacts which do
not overlap are not acceptable.
Where neutral conductors are to be solidly connected as shown on the plans, a neutral conductor plate with
fully rated CU pressure connectors shall be provided.
A single controller shall provide twelve selectable nominal voltages for maximum application flexibility and
minimal spare part requirements. Voltage sensing shall be true RMS type and shall be accurate to 1% of
nominal voltage. Frequency sensing shall be accurate to 0.2%. The panel shall be capable of operating
over a temperature range of -20 to +60 degrees C and storage from -55 to +85 degrees C.
The controller shall be connected to the transfer switch by an interconnecting wiring harness. The harness
shall include a keyed disconnect plug to enable the controller to be disconnected from the transfer switch for
routine maintenance. Sensing and control logic shall be provided on multi-layer printed circuit boards.
Interfacing relays shall be industrial grade plug-in type with dust covers. The panel shall be enclosed with a
protective cover and be mounted separately from the transfer switch unit for safety and ease of maintenance.
The protective cover shall include a built-in pocket for storage of the operators manuals.
All customer connections shall be wired to a common terminal block to simplify field-wiring connections.
The controller shall meet or exceed the requirements for Electromagnetic Compatibility (EMC) as follows:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 140
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.3 Operation
1.3.1 Controller Display and Keypad
A four line, 20-character LCD display and keypad shall be an integral part of the controller for viewing all
available data and setting desired operational parameters. Operational parameters shall also be available for
viewing and limited control through the serial communications input port. The following parameters shall
only be adjustable via DIP switches on the controller:
Repetitive accuracy of all settings shall be within 0.5% over an operating temperature range of -20C to
60C.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 141
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Voltage and frequency settings shall be field adjustable in 1% increments either locally with the display and
keypad or remotely via serial communications port access.
The controller shall be capable (when activated by the keypad or through the serial port) of sensing the
phase rotation of both the normal and emergency sources. The source shall be considered unacceptable if
the phase rotation is not the preferred rotation selected (ABC or CBA).
Source status screens shall be provided for both normal & emergency to pro-vide digital readout of voltage
on all 3 phases, frequency, and phase rotation.
A time delay shall be provided on transfer to emergency, adjustable from 0 to 60 minutes, for controlled
timing of transfer of loads to emergency.
Two time delay modes (which are independently adjustable) shall be provided on re-transfer to normal. One
time delay shall be for actual normal power failures and the other for the test mode function. The time
delays shall be adjustable from 0 to 60 minutes. Time delay shall be automatically bypassed if the
emergency source fails and the normal source is acceptable.
A time delay shall be provided on shut down of engine generator for cool down, adjustable from 0 to 60
minutes.
A time delay activated output signal shall also be provided to drive an external relay(s) for selective load
disconnect control. The controller shall have the ability to activate an adjustable 0 to 5 minute time delay in
any of the following modes:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 142
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
A SPDT contact, rated 5 amps at 30 VDC, shall be provided for a low-voltage engine start signal. The start
signal shall prevent dry cranking of the engine by requiring the generator set to reach proper output, and run
for the duration of the cool down setting, regardless of whether the normal source restores before the load is
transferred.
Auxiliary contacts, rated 10 amps, 250 VAC shall be provided consisting of one contact, closed when the
ATS is connected to the normal source and one contact closed, when the ATS is connected to the emergency
source.
LED indicating lights (16 mm industrial grade, type 12) shall be provided; one to indicate when the ATS is
connected to the normal source (green) and one to indicate when the ATS is connected to the emergency
source (red).
LED indicating lights (16 mm industrial grade, type 12) shall be provided and energized by controller
outputs. The lights shall provide true source availability of the normal and emergency sources, as
determined by the voltage sensing trip and reset settings for each source.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 143
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The following features shall be built-in to the controller, but capable of being activated through keypad
programming or the serial port only when required by the user:
Provide the ability to select commit/no commit to transfer to determine whether the load should be
transferred to the emergency generator if the normal source restores before the generator is ready to accept
the load.
Terminals shall be provided for a remote contact which opens to signal the ATS to transfer to emergency
and for remote contacts which open to inhibit transfer to emergency and/or retransfer to normal. Both of
these inhibit signals can be activated through the keypad or serial port.
An In phase monitor shall be provided in the controller. The monitor shall control transfer so that motor
load inrush currents do not exceed normal starting currents, and shall not require external control of power
sources. The in phase monitor shall be specifically designed for and be the product of the ATS
manufacturer.
The controller shall be capable of accepting a normally open contact that will allow the transfer switch to
function in a non-automatic mode using an external control device.
At the end of the specified duration the switch shall transfer the load back to normal and run the generator
for the specified cool down period. A 10-year life battery that supplies power to the real time clock in the
event of a power loss will maintain all time and date information.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 144
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Normal Failed
Load on Normal
TD Normal to Emerg
2min15s
Controllers that require multiple screens to determine system status or display coded system status
messages, which must be explained by references in the operators manual, are not permissible.
1. Event Logging
1. Data and time and reason for transfer normal to emergency.
2. Data and time and reason for transfer emergency to normal.
3. Data and time and reason for engine start.
4. Data and time engine stopped.
5. Data and time emergency source available.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 145
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. Statistical Data
1. Total number of transfers.
2. Total number of transfers due to source failure.
3. Total number of days controller is energized.
4. Total number of hours both normal and emergency sources are available.
The ATS/BPS shall be UL-1008 and IEC-60947-6-1 complied & in accordance with UL 1008 listing and be
labeled in accordance with that standard's 1 and 3 cycle, long-time ratings. ATS/BPS which are not tested
and labeled with 1 and 3 cycle (any breaker) ratings and have series, or specific breaker ratings only, are
not acceptable.
The ATS rated 800A and above must be tested for 18/30 cycles short time withstand capacity matching
breaker fault level to enable use of ACB as a back up protection device with short time delay setting for
providing discrimination with the downstream breakers.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 146
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
of capacitors and harmonic filters is within scope of contractor. All necessary hardware / supports required
for installation of the panel is scope of the works.
2.0 Standards:
The design, manufacture and performances of the power factor correction panel with capacitor banks shall
comply with all currently applicable statutes, regulations and safety codes in the locations of installations.
The capacitors used will also conform to the latest applicable Indian / British / IEC standards. In particular,
the equipment shall conform to the latest revisions of the following.
IS: 13340 , 13341 & 12672 Capacitors for power system.
IS: 2208 , 13703 HRC cartridge fuse and links upto 600V
IS: 8828 MCB
IS: 13947 MCCBs
When the above standards are in conflict with these specifications, this specification shall prevail.
The rating of the step should be decided by due consideration of de-rating due to harmonic reactors, so as to
ensure that each capacitor feeder delivers net output equivalent to the step rating. PF capacitors should be
rated for minimum 480/525 VAC, 3-ph, 50 Hz and shall be suitable to operate continuously with the
harmonic filters.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 147
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
In and suitable for continuous operation at system voltage without excess heating. One no temperature
switch should be provided internally with terminals brought outside for control.
Earthing terminal shall be provided as per clause No 4.0 of this specification. The panel shall be provided
with suitably rated T.P. copper bus bar supported on epoxy insulator. Each capacitor unit shall be connected
to main bus bar through thyristor of suitable rating with safety margin. Protective HRC/MCBs /MCCBs
fuses of suitable rating shall be provided with base / holder as mentioned in the drawing. Connection shall
be made with PVC insulated flexible copper cables having crimped copper lugs. All capacitor units shall be
earthed; sufficient ventilation shall be provided to limit the temperature rise to maximum 85oC. Cooling
fans shall be provided to each heat sink as per requirement. Suitable exhaust fans shall be provided in order
to dissipate the internal heat of the panel and maintain the internal temperature rise of the panel within safe
limits. The operation of fans shall be automatic with temperature sensor. Drawing pocket shall be provided
at the door of each panel. A 15-amp switch & socket and the lamp holder shall also be provided for panel
illumination at the suitable location.
The main Bus bar shall be terminated on suitably rated SFU /MCCB /SDU / ACB. Detachable gland plates
shall be provided with suitable knockout for incoming cable connection from bottom/top as specified.
Capacitor unit shall be mounted a frame of adequate strength construction.
The panel shall be mounted on MS channel section at the bottom for easy installation. The panel shall be
provided with lifting hooks /eye bolts for handling. Automatic Power Factor Correction Relay shall be
provided with all related circuits and three load CTs for each phase in order to control/ achieve target
Power Factor OR unity as per setting.
The controller shall be capable of correcting Power Factor within 2 to 120 sec in case of RTPFC. The
capacitor shall be switched ON and OFF using thyristors from APFC controller.
Average compensation required and compensation supplied shall be continuously monitored for all the three
phase simultaneously and total low kVAr requirement shall be calculated accordingly. It would
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 148
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
automatically switch ON and OFF the capacitor bank so as to attain the set target power factor. The panel
shall be provided as per respective drawing.
6.0 EARTHING
The enclosure of capacitor unit shall be provided with 2 nos. 10 mm earth terminals or strip, each complete
with two plain and one spring washer, nuts etc. These terminals shall be effectively bonded to the common
sheet steel framework. Each bank in case of APFC will have two external terminals in the bus bar chambers
complete with hardware.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 149
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 150
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. SPECIFICATIONS
1.1.1 CABLE TRENCH
Cable trench shall be dug to the minimum depth of 1 mtr and the width shall dependent on the no of cables
to be kept with the layer of brick in between two cables.
1.1.2 BRICKS
The bricks shall be hand or machine moulded and made from suitable soils and kiln burnt. They shall be free
from cracks, flaws and modules of free lime. They shall have smooth rectangular faces with sharp corners
and shall be uniform in colour. The bricks shall be moulded with a frog of size 100 mm. x 40 mm., and 10
mm. to 20 mm. deep on one of its flat sides. The bricks shall not break when thrown on the ground from a
height of 6 m. B grade locally available standard brick shall be used.
1.1.3 SAND
Sand shall be natural sand, clean, well graded, hard, strong, durable and gritty. Sand particles should be free
from injurious amounts of dust, clay, kankar nodules, soft or flaky particles of shale, alkali, salts, organic
matter loam, mica or other deleterious substances and shall be got approved from the CLIENT AND/OR
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 151
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ITS ARCHITECT. The sand shall not contain more than 8% of silt as determined by field test, if necessary
the sand shall be washed to make it clean. The sand used by civil agency shall be used.
1.1.5 WORKMANSHIP
The cable shall be laid side by side in trench with brick covering on all the three sides. The trench shall be
such that sharp bends shall be avoided while laying the cable. The bedding of fine sand under the cable shall
be not less than 6 mm. The trench shall be terminated in Manholes with specified size of R.C.C. hume pipes
as shown in drawing. Cable markers shall be provided through out the route of cable at 10 mtrs distance.
The trenches shall be refilled after the cable are laid and the Ground level shall be done as per original after
pressing the same. The cables shall be checked for insulation resistance and continuity tests shall be carried
out.
D) DISTRIBUTION BOARDS
1. Scope:
This specification covers performance, design, material, construction, manufacture, inspection, testing,
packing forwarding, delivery at site, testing and commissioning of factory fabricated distribution boards
with all accessories complete in all respects as described in this specification and single line diagrams.
Whether called for specifically or not, all accessories required for normal operation of equipment are
deemed to be considered as a part of the contractors scope of supply. Hardware / fabricated supports
required for mounting and installation of the DB is within the scope of work.
It is not the intent to specify completely herein, all details of design and construction of the equipment.
However, the equipment shall conform in all respects to high standard of Engineering, design and
workmanship and be capable of performing in continuous commercial operation up to the Manufacturers
guarantees in a manner acceptable to the Engineer, who will interpret the meaning of the drawings and
specifications and shall be entitled to reject any work or material which is not full accordance therewith.
2. Specifications
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 152
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Distribution boards shall be fabricated from 14 gauge M.S. sheet or shall be readymade as specified in the
make of material list. It shall be of double door type with hinged (lockable if required) door suitable for
recessed mounting in wall. Distribution boards shall be powder coated with 7-tank process application.
The distribution boards shall be provided with phase barriers, wiring channels to accommodate wires and
individual per phase neutral links with nos. of terminals (holes) equivalent to nos. of . circuit in D.B.. There
shall be separate or individual earth link as per requirement. Proper arrangement shall be made for mounting
of MCBs and other accessories.
Distribution boards shall meet with the requirements of IS 8623 and marking arrangement of bus bars shall
be in accordance with I.S. standards.
Bus bars shall fully shrouded and shall be suitable for the incoming switch rating and sized for a temperature
rise of 35 C over the ambient. Each board shall have two separate earthing terminals. Separate Neutral bars
per phase with one terminal for each outgoing ckt shall be provided. Circuit diagram (laminated) indicating
the load distribution shall be pasted on the inside of the DB as instructed. One earthing terminal for single
phase and two terminals for 3 phase DB's shall be provided with an earth strip connecting the studs and the
outgoing ECU earth bar.
The top and the bottom faces of the D.B. shall be provided for conduit entry of minimum 1 dia. The faces if
asked shall be kept detachable.
All outgoing feeders shall terminate on a terminal strip which in turn is interconnected to the MCB by
means of insulated single conductor rigid copper wires as follows
Each DB shall have indicating lamps preferably neon type denoting power availability in the board after the
switch indicating lamps shall be complete with fuses.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 153
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
time thermal over load and instantaneous over current tripping elements, with trip-free mechanism. In case
of multi-pole breakers, the tripping must be on all the poles and operating handle shall be common. Breakers
must conform to IEC 60898 / IS 8828-1996. Pressure clamp terminals for stranded/solid conductor insertion
are acceptable up to 4 sq. mm. aluminium or 2.5 sq.mm. copper and for higher ratings, the terminals shall be
suitably shrouded. Wherever MCB isolators are specified they are without the tripping elements.
4. RCCB / ELCB
The RCCB should suffices all the requirements of IS as per code IS - 12640 - 2000. The RCA should be
current operated and not on line voltage.
5. Workmanship
The D.B. shall be properly grouted in the wall in concealed manner taking care that the powder coating is
not scratched and dents are not formed on the D.B. The MCBs and ELCBs. In the distribution boards shall
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 154
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
be fixed as per the circuit details provided. All the wires terminating in the MCBs and the ELCBs shall be
lugged for proper contact and ferrules depicting the circuit nos shall be provided. D.B.s mounted in
concealed manner shall have a groove around it so as to save the finish of the plaster and colour during
future opening of the door. The distribution boards shall have circuit chart tagged on the door for future
maintenance. Danger notice plates shall be fitted to the distribution boards with screws and not stuck so as
to assure its presence for a longer duration.
All cables shall be adequately protected against any risk of mechanical damage to which they may be liable
in normal conditions of handling during transportation, loading, unloading etc.
The cable shall be supplied in single length i.e. without any intermediate joint or cut unless specifically
approved by the Engineer.
The cable ends shall be suitably sealed against entry of moisture, dust, water etc. with cable compound as
per standard practise.
1.1.2 Conductor:
Uncoated, annealed copper, of high conductivity, upto 4 mm2 size the conductor shall be solid and above 4
mm2 the conductors shall be concentrically stranded as per iec: 228. The conductor shall be of copper for all
cables up to & including 100A. Above 100A all cable shall be with Al. conductors.
1.1.3 Insulation:
Cross link polyethylene (XLPE) extruded insulation rated at 70oc. Cables for all life safety equipments
including lifts shall be of FRLS grade.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 155
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1.5 Assembly:
Two, three or four insulated conductors shall be laid up, filled with non-hygroscopic material and covered
with an additional layer of thermoplastic material.
1.1.6 Armour:
Galvanised steel flat strip / round strips applied helically in single layers complete with covering the
assembly of cores.
For cable size upto 10 sq mm : Armour of 1.4 mm dia G.I. round wire
For cable size above 10 sq mm : Armour of 4 mm wide 0.8 mm thick GI strip
1.1.7 Sheath:
ST -2 PVC along with polypropylene fillers to be provided.
Inner sheath shall be extruded type and shall be compatible with the insulation provided for the cables.
Outer sheath shall be of an extruded type layer of suitable PVC material compatible with the specified
ambient temp. of 50oc and operating temperature of cables. The sheath shall be resistant to water, ultra
violet radiation, fungus, termite and rodent attacks. The colour of outer sheath shall be black.
Sequential length marking along with size and other standard parameters shall be required at every 1.0 mtr
on the outer sheath.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 156
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Short runs if cable laid in pipes, closed masonry trenches and similar protected or secured enclosures need
not be armoured.
PVC and XLPE cables, when armoured, shall have galvanised steel wires (flat or round) for armouring.
ELECTRIC CABLE: 1100 V, SIZE :___C X ____ MM2 with Manufacturers name, year of manufacturing
and ISI symbol.
Cable shall be supplied in length of 500 mtrs or as required in non-returnable drums of sufficiently sturdy
construction.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 157
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Cables of more than 250 meters shall also be supplied in non-returnable drums.
Each drum shall bear on the outside flange, legibly and indelibly in the English literature, a distinguishing
number, the manufacturers name and particulars of the cable i.e. voltage grade, length, conductor size,
cable type, insulation type, and gross weight shall also be clearly visible. The direction for rolling shall be
indicated by an arrow. The drum flange shall also be marked with manufacturers name and year of
manufacturing etc.
1.9 Ferrules:
Ferrules shall be of self-sticking type and shall be employed to designate the various cores of the control
cable by the terminal numbers to which the cores are connected, for ease in identification and maintenance.
1.10 Workmanship
Cables shall be laid in the routes marked in the drawings. Where the route is not marked, the Contractor
shall mark it out on the drawings and also on the site and obtain the approval of the Engineer and/or Its
Consultant before laying the cable. Procurement of cables shall be on the basis of actual site measurements
and the quantities shown in the schedule of work shall be regarded as a guide only.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 158
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Bending of cables shall be in accordance with standards given by manufacturer and also space between 2
cables equivalent to diameter of the cable shall be maintained.
In the case of cables buried directly in ground, the cable route shall be parallel or perpendicular to roadways,
walls etc unless marked on drawing by consultant. Cables shall be laid on an excavated, graded trench, over
a sand or soft earth cushion to provide protection against abrasion.
Contractor shall submit complete voltage drop calculation analysis with necessary derations as per the length
at site prior to ordering of the cables.
Cable markers shall be used to identify external underground cables / cable route. The markers shall be
installed at max distance of 10mtr. Nylon pull wires shall be left in all pipes / hume pipes for first time and
future pulling of cables. At start / end of the cables and also in between at every 30 mtrs max, cable markers
of Al type shall be used.
All cables shall be full runs from panel to panel without any joints or splices. Cables shall be identified at
end termination indicating the feeder number and the Panel/Distribution board from where it is being laid.
Cable termination for conductors up to 4 sq. mm may be insertion type and all higher sizes shall have
compression type lugs. Cable termination shall have necessary brass glands. The end termination shall be
insulated with a minimum of six half-lapped layers of PVC tape. Cable armouring shall be earthed at both
ends.
In case of cables entering the buildings, the sleeves /cutouts shall be laid in slant position, so that no
rainwater may enter the building. Once the cables are laid, sealing of the sleeves / cutouts for fire and water
safety, shall be done by others as per architectural details.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 159
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
E) INTERNAL WIRING
1. SPECIFICATIONS
Flexible conduits shall be formed from a continuous length of spirally wound interlocked steel strip with a
fused zinc coating on both sides. The conduit shall be terminated in brass adapters.
ACCESSORIES:
PVC conduit fittings such as bends, elbows, reducers, chase nipples, split couplings, plugs etc. shall be
specifically designed and manufactured for their particular application. All conduit fittings shall conform to
IS: 2667-1964 and IS: 3857-1966. All fitting associated with galvanized conduit shall also be galvanized.
WIRES:
All wires shall be single core multi-strand/ flexible copper or single strand Copper ( if specified in BOQ),
PVC insulated FR grade as per IS: 694 and shall be 660 V\1100 V.
All wires shall be colour coded as follows:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 160
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Switches shall be modular type with silver-coated contacts. Sockets shall be 5 pins with switch and plate
type cover. Combination of multiple switch units and sockets should be used to minimize the switch boxes.
For heavy duty, metal clad sockets with M.C.B / Isolator mounted in a galvanized steel box shall be
provided.
2. B. WORKMANSHIP
The size of conduit shall be selected in accordance with the number of wires permitted under table given
below. The minimum size of the conduit shall be 25 mm diameter unless otherwise indicated or approved.
Size of wires shall not be less than 1.0 sq.mm. Copper or 2.5 sq.mm. Aluminium.
S- runs of conduits which have distance not exceeding 4.25 m. between draw boxes & which do not
deflect from the straight by an angle more than 15 degree.
B- runs of conduits, which deflect, from the straight by more than 15.
Conduits shall be kept at a minimum distance of 100 mm. from the pipes of other non-electrical services.
And maintain minimum 300 mm distance between telephones, TV & Computer piping.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 161
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Wiring for short extensions to outlets in hung ceiling or to vibrating equipments, motors etc., shall be
installed in flexible conduits. Otherwise rigid conduits shall be used. No flexible extension shall exceed 1.25
m.
Conduits run on surfaces shall be supported on metal 12 mm. thick G.I. pressure saddles which in turn are
properly screwed to the wall or ceiling. Saddles shall be at intervals of not more than 500 mm. Fixing screws
shall be with round or cheese head and of rust-proof materials. Exposed conduits shall be neatly run parallel
or at right angles to the walls of the building. Unseemly conduit bends and offsets shall be avoided by using
fabricated mild steel junction/pull through boxes for better appearances. No cross-over of conduits shall be
allowed unless it is necessary and entire conduit installation shall be clean and neat in appearance.
Conduits embedded into the walls shall be fixed by means of staples at not more than 500 mm. intervals.
Chases in the walls shall be neatly made and refilled after laying the conduit and brought to the finish of the
wall but the building Contractor will do final finish.
Conduits buried in concrete structure shall be put in position and securely fastened to the reinforcement and
got approved by the CLIENT AND/OR ITS ARCHITECT, before the concrete is poured. Proper care shall
be taken to ensure that the conduits are neither dislocated nor choked at the time of pouring the concrete
suitable fish wires shall be drawn in all conduits before they are embedded.
Where conduit passes through expansion joints in the building, adequate expansion fittings shall be used to
take care of any relative movement.
Inspection boxes shall be provided for periodical inspection to facilitate withdrawal and removal of wires.
Such inspection boxes shall be flush with the wall or ceiling in the case of concealed conduits. Inspection
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 162
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
boxes shall be spaced at not more than 12 meters apart or two 90 solid bends or equal. All junction and
switch boxes shall be covered by 6 mm clear plate. These junction boxes shall form part of point wiring or
conduit wiring as the case may be including the cost of removing the cover for painting and re-fixing. No
separate charges shall be allowed except where specially mentioned.
Conduits shall be free from sharp edges and burrs and the threading free from grease or oil. The entire
system of conduits must be completely installed and rendered electrically continuous before the conductors
are pulled in. Conduits should terminate in junction boxes of not less than 32 mm. deep.
An insulated earth wire of copper rated capacity shall be run in each conduit.
All final branch circuits for lighting and appliances shall be single conductor/ stranded/ flexible wires run
inside conduits. The conduit shall be properly connected or jointed into sockets, bends, and junction boxes.
Branch circuit conductor sizes shall be as shown in the schedule of quantities and or drawings.
All circuits shall preferably be kept in a separate conduit up to the Distribution Board. No other wiring shall
be bunched in the same conduit except those belonging to the same phase. Each lighting branch circuit shall
not have more than ten outlets or 800 watts whichever is lower. Each conduit shall not hold more than three
branch circuits.
Flexible cords for connection to appliances, fans and pendants shall be 650/1100 V grade (three or four
cores i.e. with insulated neutral wire of same size) with tinned stranded copper wires, insulated, twisted and
sheathed with strengthening cord. Colour of sheath shall be subject to the CLIENT AND/OR ITS
ARCHITECTS approval.
Looping system of wiring shall be used. Wires shall not be jointed. Where joints are unavoidable, they shall
be made through approved mechanical connectors. No such joints shall be made unless the length of the
sub-circuit, sub-main or main is more than the length of the standard coil.
Control switches shall be connected in the phase conductors only and shall be `ON' when knob is down.
Switches shall be fixed in 3 mm. thick painted or galvanized steel boxes with cover plates as specified.
Cadmium plated brass screws shall be used.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 163
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Power wiring shall be distinctly separate from lighting wiring. Conduits not less than 25 mm. and wires not
less than 2.5 sq.mm. copper shall be used.
Every conductor shall be provided with identification ferrules at both ends matching the drawings.
Insulation resistance.
Earth continuity.
Polarity of single pole switches.
General: All the wiring switch board, outlet points shall be done in a concealed manner in wall & slab in
PVC conduit of minimum 25 mm dia. (medium gauge) & with 650v / 1100v grade PVC insulated flexible
copper conductor wire. The switches should be modular with moulded cover plates, blank plates for outlet
boxes. The accessories, connectors, sockets, should be fixed with brass chrome / cadmium plated machine
screw. For fan points the rates should be with hum -free type 300 W regulators as required to complete the
point wiring. The wiring shall be as per IS: 732 and IS: 4648. The wiring shall be done in a looping manner
so as to avoid junction boxes at any place. All the looping shall be done only in the switchboard and outlet
points. The size of the wire shall be as per the specification. Colour code shall be strictly followed.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 164
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Earth 2.5 m m2
Light, fans, exhaust fan, 5 Amp. On board plug point, two way light points, bell point etc from switch to
outlet.
Phase / Neutral 1 m m2
Earth 1 m m2
From D.B. to switch board lighting / 5 A socket etc i.e. circuit mains part of point wiring
15/20 Amps. Socket outlet for appliances or looped from sockets with 4 sq mm ckt.
Phase / Neutral 2.5 m m2
Earth 1.5 m m2
Circuit mains of same phase shall be drawn in one pipe with prior permission/discussion with the
consultant.
Separate phase, neutral and earthing wire of sizes recommended by consultant shall be drawn for each and
every circuit main.
Mains for lighting and on board plug points shall be of one-size higher wires than those used in off.
The point definition shall be conduting and wiring from D.B. to S.B. and there from to final outlet point
including switches and accessories, junction boxes, fan boxes, zarri work with cement sand etc of
approved make.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 165
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Light fixtures as per specs in the drawing of approved makes shall be installed. The fixtures shall be
complete with ballast and shall be prewired by the manufacturer.
2. Workmanship
The fixture shall be installed on wall / ceiling as directed and as per manufacturers instruction, with
necessary accessories for surface, concealed, suspended from ceiling, bracket mounting etc. The job also
includes connection of fixture with respective outlet point with heat resistant wires through heat resistance
sleeve and PVC connector. Earthing shall be provided to the fixtures.
4. Specifications
Street light poles, M.S. poles shall be as per the drawing given. The sections for the pipe shall be as
shown in the drawing. The poles shall be welded properly and grinding shall be perfect to show smooth
surface and stability shall be maintained. The light fixtures to be mounted above the poles shall be as
specified in the BOQ. All the poles shall be treated with 2 coats of red oxide and after the putty and other
works shall be spray painted with automative category paints only. In case of powder coating 7 tank
processes shall be adopted. The painting or the powder coating option shall be as per the BOQ.
5. Workmanship
All the light poles shall be brought to site and shall be stored in such a place so as to avoid rusting and
brazing of the poles. The poles shall be erected as per the drawing and the top level of all the poles shall
be similar. The poles shall be at right angle with the ground. Necessary civil works and spiral earthing
shall be done as shown in drawing. No additional holes shall be drilled in poles at site for enabling the
cable works. Poles with damage in colour or indentations shall be rejected and if Engineering in charge
approves for damage in colour the same shall be finished at the site.
6. Mode of Measurement
The poles shall be measured in nos and the cabling for the same shall be measured in rmt.
Poles or external light fixtures shall be free from dents or flaking of powder coating until hand over.
Damaged material shall be rejected / replaced as per consultants / EIC instructions.
G) CHEMICAL EARTHING
1. Earth Rod
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 166
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Earth Rod shall be mentioned in earthing schematic. Length of copper bonded steel rod shall be 10
feet of 32 mm dia.
The minimum copper bonding thickness is 250 microns.
Copper bonding on the steel rod is through Nickel interface.
Gives lowest possible resistance to ground also resist to corrosion.
It shall be molecularly bonded with copper to high strength steel cores.
The life of the earth rod shall be minimum 20 years.
Earth resistance of < 3 shall be achieved at farthest point for normal earthing & <1 shall be achieved
at farthest point for clean earthing.
The size & material of earthing conductor and nos. of earth pits are as specified in drg. Though contractor
shall confirm the same as per local CEIG dept. requirements & any changes required for the same is
within scope of contractor.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 167
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The earth conductors (Cu. / Al.) inside the building shall be properly clamped / supported on the wall with
Galvanized Iron clamps and Mild Steel Zinc Passivated screws / bolts. The conductors outside the
building shall be laid at least 600 mm. below the finished ground level or as per site condition as approved
by engineer.
The earth conductors shall either terminate on earthing socket provided on the equipment or shall be
fastened to the foundation bolt and / or on frames of the equipment. The earthing connection to equipment
body shall be done after removing paint and other oily substances from the body and then properly be
finished.
For termination / connectors for the earth strip / wires; factory fabricated connectors shall be used.
Braising and other local means for joining shall be not carried out. The connectors shall be tested as per
BS EN 50164 : 2000.
The complete lightning protection system will comprise the following key components.
(a) Advanced lightning rod
(b) Mounting support
(c) High voltage shielded cable
(d) Lightning Strike Recorder
(e) Dedicated earthing system
The advanced lightning rod shall be configured as a spheroid which is comprised of separate electrically
isolated panels surrounding an earthed central finial.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 168
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The insulation material used to electrically isolate the panels shall be comprised of a base polymer which
provides high ozone and UV resistance with a dielectric strength of 24 38 KV/mm.
The external shape of the advanced lightning rod shall be such that it will limit the development of sharp
point corona discharge under static thunderstorm conditions.
The upper section of the central finial shall be rounded to provide a blunt surface.
The upper section of the central finial shall be rated to withstand 200KA.
An air gap shall be provided between the individual electrically isolated panels (4 panels) and the blunt
configured tip of the central rod. Dome shapes and pointed central rods will not be acceptable.
Arcing shall occur between the panel sections of the spheroid and the blunt configured finial tip only upon
the progression of a lightning leader.
The advanced lightning rod shall have no moving parts and will have no dependence on external power
supply or batteries. There should be no high impedance static drain unit between the central rod and the
panels.
Under a normal atmosphere all components of the advanced lightning terminal shall be non-corroding.
The advanced lightning rod shall be installed at a minimum of 10 metres from the ground.
The advanced lightning rod shall be insulated from all surrounding points and features of the structure
being protected.
The advanced lightning rod shall not be installed in a corrosive environment unless the manufacturers
written approval has first been granted.
The advanced lightning rod shall be installed as per the manufacturers instructions.
The advanced lightning rod shall not be of the ESE type and all lightning terminals claiming compliance
to NF C17-102 shall not be considered suitable.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 169
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The advanced lightning rod shall have been tested to the following standard IEC 601:1989.
The lightning rod shall be shown to have withstood a minimum current impulse of a 180kA 8/20 s
waveform as per the test standard IEC 60-1:1989.
The mounting pole and supports shall be securely fixed with brackets and guy wires where required.
The down conductor shall pass through the centre of the insulating pole for the entire length of the pole.
4.2 The main copper conductor within the high voltage shielded cable shall have a minimum cross
sectional area of 50mm.
4.3 The outer diameter of the high voltage shielded cable shall be less than 38mm.
4.4 The high voltage shielded cable shall have a maximum inductance of 25 nH/m.
4.5 The main copper conductor shall allow for direct connection to the lightning rod through the use
of a compression lug.
4.6 The high voltage shielded cable shall be fixed to the structure through the use of suitable saddles
every two metres for the length of the cable route.
4.7 The high voltage shielded cable shall be installed as per manufacturers instructions and shall not
be subject to bends of less than 0.6 metres radius.
4.8 The high voltage shielded cable shall have been tested to the following standard IEC 60-1:1989.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 170
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4.9 The high voltage shielded cable shall have been subjected and successfully withstood a maximum
voltage of 280kV in compliance to IEC test standard, IEC 600601, 2nd edition, 1989-11.
5.2 The lightning strike recorder shall contain a mechanical 6 digit display which will register all
lightning discharges with a sensitivity of 1500A 8/20 us peak current impulse.
5.3 The lightning strike recorder shall be housed in a IP 67 rated enclosure and will operate without
reliance on batteries or an external power source.
5.4 The lightning strike recorder shall be installed as per the manufacturers instructions.
5.5 It shall be shown that the event recording device has been successfully tested under test standard
IEC 60-1:1989.
6.0 EARTHING
6.1 The earthing system shall incorporate the following individual components or a combination of
the following 25 x 1mm flat copper tape buried to a depth of not more than 800mm or by deep
driven copper bonded steel core earth rods. All components of the earthing system shall be
electrically connected to the central injection rod which is securely connected to the lower end of
the high voltage shielded cable.
6.2 The earthing system shall be installed so that the final impedance reading does not exceed 10
Ohms unless otherwise stipulated by the lightning protection manufacturer or consulting engineer.
6.3 It is recommended that the earthing system is bonded to all structural reinforcing steel of the
building, along with all connecting services.
6.4 The use of ground resistance improvement material shall be applied in order to reduce the
resistivity levels of the earthing system.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 171
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. SPECIFICATIONS
TELEPHONE CABLES AND WIRES:
The type of cables and the services shall be as follows:
Indoor Multipair PVC sheath armoured / un-armoured as specified 0.6 mm tin Cu. Cable.
Outside Multipair PVC sheath armoured / jelly filled as specified 0.6 mm tin Cu. Cable.
All multi core cables and wires shall be of tinned copper conductor of not less than 0.6 mm dia and shall
be colour coded twisted pairs with rip cord.
The conductor resistance shall be less than 150 ohms per KM and the insulation resistance between the
conductors not less than 50 mega ohms and the nominal capacitance of about 0.1 microfarad per
kilometre.
Cables laid underground or locations subject to dampness and flooding shall be filled with polyethylene
compound and shall have sufficient protection against moisture and water ingress.
All armouring shall be of galvanized steel wires and protected against corrosion by an outer sheath of
PVC in the case of indoor cables and polyethylene in the case of outdoor cables. Outer sheathing must be
fire retarding and anti-termite.
All un-armoured single core cables and inner sheath of armoured cables shall be provided with ripcord.
The tag blocks shall be mounted inside fabricated sheet steel boxes with removable hinged covers and
shall be fully accessible. The enclosure shall be painted with 2 coats of red oxide and stove 172ntercoo.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 172
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Telephone outlet socket shall be of the same make as that of the switches and accessories. The outlet
sockets shall consist of 2 A 2 Pair polyethene connector in M.S.I / PVC boxes with switch plate of the
same make as that of switches and telephone socket. The telephone outlet socket unless and otherwise
specified shall be jack type and not pin type.
COMPUTER WIRES:
The computer wires shall be of 4 pair enhanced Cat 6 category and shall be of the makes as specified in
the tender.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 173
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
FLOOR RACEWAY:
Floor raceway of hot dip 174 intercoole / aluminium sheet of 14 g / 2.0 mm shall be used and the
dimensions for the same shall be as per the BOQ. The raceways shall be as per the make specified in the
tender. The raceways shall be free of any sort of welding edges or other sharp edges to protect cutting of
wires during pulling. The raceways shall be laid with use of junction boxes fabricated from 14 g hot dip
GI as per drawing.
B. WORKMANSHIP
All cables shall be on cable racks and neatly stitched together.
The connection at the tag blocks shall be silver soldered so as to achieve minimum contact resistance.
The final branch connections with single pair cables in conduits and the maximum number of cables in
each conduit shall be as follows:
The tag blocks shall be mounted inside fabricated sheet steel boxes with removable hinged covers and
shall be fully accessible. The enclosure shall be painted with 2 coats of red oxide and stove 174ntercoo.
J) UPS
Scope
The present special contract specifications constitute a call for best offers for the supply of:
Uninterruptible Power System(s) (hereinafter referred to as UPS) rated at 3 X 40kVA, 3 X 20KVA and 2
x 15KVA featuring NiCad batteries housed in one or more external racks/cubicles and providing a
minimum autonomy as defined under Batteries herein.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 174
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The present specifications contain minimum requirements. All offers must be completed strictly in
accordance therewith, either by confirming data or by filling in the spaces provided, where requirements
are not met.
Any deviations or exceptions to the minimum requirements must appear in the offer.
Where no exceptions are shown, the requirements of the present specifications will be considered as
accepted.
The UPS will have a CE mark as specified by Directives 73/23, 93/68, 89/336, 92/31 and 93/68.
The UPS will be designed and produced according to the following specifications:
IEC/EN 62040-1-1 General and safety requirements for UPS used in operator access areas.
EN 62040-2 Electromagnetic compatibility (EMC) requirements
IEC/EN 62040-3 Performance requirements and test methods
Design Specifications
The Uninterruptible Power System (UPS) will include the following operational components:
Full IGBT Rectifier/battery charger
IGBT Inverter
Maintenance bypass switch
Static switch
Batteries.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 175
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
For the battery charger function, this converter will include built-in fuses and a control circuit for the
voltage and battery recharging current. The ripple current to the batteries will be less than 0.05 C10. A
microprocessor control function will perform the following operations:
IGBT Inverter
The IGBT inverter will have a PWM digital vector control system (DSP based), capable of converting
DC voltage from the IGBT rectifier or battery into AC voltage. A rated output filter will create an output
voltage sinusoidal envelope.
The control circuit, in addition to normal functions, will automatically adjust nominal output power in
accordance with ambient temperature.
Inverter should be able to deliver full active power at Unity power factor (KVA=KW)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 176
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The control logic will be handled by digital algorithms (using vector control techniques), similar to those
used for the rectifier and the inverter. The static bypass shall be equipped with a back feed protection
device compliant with clause 5.1.4 of IEC/EN 62040-1-1; and a relay signal contact for the control of the
external back feed isolator to be installed on the bypass line upstream from the UPS.
6.0 Batteries
The VRLA, WET or NiCad batteries will feature an enclosure made of self-extinguishing material.
The batteries will be housed in one or more racks/ cubicles and will be protected by fuses located on each
pole and via a dedicated switch.
OPERATING MODES
This section describes the different operating modes of the Uninterruptible Power System.
The UPS, using the above-mentioned digital vectorial control (DSP system), will be able to operate both
in double conversion and digital interactive modes.
The operating mode may be factory set by the manufacturer during testing or by the customer using the
appropriate diagnostic and control software.
The IGBT inverter will be synchronized with the bypass line so that the load can be transferred from the
inverter (conditioned line) to the bypass supply (direct line) and vice versa without any break in the
supply to the load.
In all operating modes, the battery charger will provide the power necessary to keep the battery fully
charged.
Upon failure or reduction of the primary AC source, the load will be supplied by the battery through the
inverter. During this phase, power will be drawn from the battery. Visible and audible signals will alert
the user to this operating state. The remaining autonomy time will be calculated by a diagnostic algorithm.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 177
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Upon return of the primary AC source to within tolerance limits, the Uninterruptible Power System will
recommence operating in normal mode.
In the event of an inverter overload, manual stop or failure or temporary overload downstream of the
UPS, the load will be automatically transferred to the bypass supply source without interruption.
In the event of an overload with an unsuitable supply, the Uninterruptible Power System will not transfer
the load but will continue to supply it from the inverter for a period of time dependent upon the extent of
the overload and the characteristics of the UPS.
The user will be alerted of these anomalous operating conditions via the alarm.
If the direct line is outside the permitted tolerances, the load will be automatically transferred to the
conditioned line (inverter) without interruption.
In the absence of power supply to the direct and conditioned lines, the battery will supply power to the
loads through the inverter. During this phase, power will be drawn from the battery and the battery charge
will be reduced. Visible and audible signals will alert the user to this operating state. The remaining
autonomy time will be calculated by a diagnostic algorithm.
When the quality and reliability of the direct line return within permitted limits, the UPS will
automatically start supplying the load from the direct line.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 178
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Warning/fault: this page contains information regarding various anomalies concerning power converters
such as the bypass, rectifier, inverter and booster/charger. In addition to this there is also warning and
fault information relating to the battery and the load.
Events log: displays the date and time of important UPS events, alarms and other warnings.
Measurements: this page holds the full set of measurements for each functional block (rectifier, bypass,
booster/charger, batteries, inverter and load).
Battery: displays the battery status/values including temperature, cell voltage, capacity and run time as
well as commands for allowing the user to configure battery testing.
Tools: this page allows users to customize the settings of the LCD display and to select the desired
language, choosing between 15 languages.
Controls
The UPS will be provided with the following controls:
Inverter start
Inverter stop
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 179
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Reset faults
Buzzer/mute alarm
Measurements
The UPS will provide the measurements (voltage, current and frequency) for every single internal
functional block and this information will be directly accessible on the display, via the measurements
button.
A voltage-free input will also be provided to disable the static switches and all power converters (EPO) in
case of emergency.
Programmable I/O contacts (at least 4 voltage-free outputs and 2 inputs).
TELEMONITORING
This section defines the requirements of the system for remote monitoring and control from the Service
Centre.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 180
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The system will guarantee single or parallel UPS surveillance, 24 hours a day for 365 days a year by
181ntercoole technical personnel operating remotely. The system will provide a detailed, preventive
analysis of connected UPS, without any of the disruption associated with an on-site visit.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 181
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
TECHNICALDATASHEET
VENDOR
PARAMETERS UNIT SPECIFICATION
CONFIRMATION
Inverterinputcharacteristics
Nominal voltage (V) 400 V 4wire
Toleranceonvoltage (%) 15%,+20%@100%load
Nominalfrequency(60Hzselectable) (Hz) 50
Toleranceonfrequency (%) 10
Inputpowerfactor@100%load >0.99
Totalharmonicdistortion(THDi)@fullload (%) <3
Walkin/Softstart (Sec) 10(1to90selectable)
RectifierHoldOFF(Sec) (Sec) 10(1to180selectable)
Inverteroutputcharacteristics
Nominalvoltage(380/415selectable) (V) 400 V 4wire
Nominalfrequency(60Hzselectable) (Hz) 50
Nominalpower@40C (kVA) 200
NominalPower@40C(kW) 200
Automaticadjustmentofnominaloutputpoweras
(%) @25c=110%
afunctionoftemperature
(%) @30c=110%
(%) @40c=110%
Outputvoltagestabilityinsteadystatecondition
forinputwithinpermittedlimitsandload (%) 1%
variationsfrom0to100%
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 182
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
VENDOR
PARAMETERS UNIT SPECIFICATION
CONFIRMATION
Stabilityindynamicconditionsfor100%loadstep
(%) 5%
variations
Loadcrestfactorwithoutderating 3:1
Outputvoltagedistortionwith100%linearload (%) <1
Outputvoltagedistortionwithnonlinearloadas
(%) <3
specifiedbyIEC/EN620403
Outputfrequencystabilityinsynchronizationwith
(%) 1
mains(234selectable)
Outputfrequencystabilitywithinternalclock (%) 0.1
Frequencyslewrate (Hz/sec) <1
Permittedoverload:
for10minutes (%) 125
for60seconds (%) 150
Shortcircuitcurrent:
300%In (ms) 10
150%In (s) 5
Characteristicsofelectronicstaticchangeover
switch
Nominalvoltage(380/415selectable) (V) 400
Toleranceonvoltage(515selectable) (%) 10
Nominalfrequency(60Hzselectable) (Hz) 50
Toleranceonfrequency(234selectable) (%) 1
UPScharacteristics
MaximumUPScabinetdimensionsWxHxD (mm)
Noiselevelmeasured@1meterand@100%load
(dBA) 70dba
accordingtoISO3746
AC/ACefficiencydoubleconversionmode@
(%) 94.5
100%load(inbuiltK13iso.Transformer)
Efficiency in digital interactive mode @ 100% load (%) 98
EMCcompatibilityasperEN620402 ClassC3
Degreeofprotection IP20
Framecolour RAL7021
The constructional and functional characteristics of UPS must be in line with the state-of-the-art
technology in this field.
The supplying company must be able to provide proof that it is ISO 9001-2000 and ISO 14001 certified
for design and manufacturing and for the provision of services.
The UPS will be guaranteed for one year during which time the Supplier will provide technical assistance.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 183
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
GENERAL:
SCOPE:
1.1 This general specification together with the equipment sheets and attachments defines the minimum
requirements the design, performance, inspection, testing and supply diesel engines for general
industrial purposes.
1.2 The construction, design and rating of the diesel engine shall meet fully, the requirements of the
specified driven machine and the Vendor shall select and provide the requisite ancillaries and controls
with the diesel engine for its safe and satisfactory operation.
1.3 No deviations or exceptions from this specification shall be permitted without the written approval of
the purchaser. Intended deviations supported by reasons there of shall be separately listed by the
vendor and submitted with the bid for the consideration of the Purchaser.
1.4 Compliance with this specification shall not relieve the vendor of the responsibility of furnishing
equipment and accessories of proper design, materials and workmanship to meet the specified
operating conditions.
1.5 This general specification supplements the specific requirements contained in the attached equipment
data sheets. In the event of any contradiction between the two, the information contained in the latter
shall govern.
1.6 Other attachments of the Material Requisition from a apart of this specification.
1.7 TERMS AND DEFINITIONS:
1.7.1 The Net Calorific value of fuel is defined as the heat resulting from the complete combustion of a
unit quantity of fuel oil and air, without condensation of the water vapor. A net calorific value of
9,720 Kcal/Kg (As per IS: 1460 Rev.2) shall be considered while declaring the fuel consumption
and for testing purposes.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 184
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.7.2 The unit of horse power as defined in this specification is the metric horse power equivalent to
4,500 n-Kg/Min. The horse power in F.P.S. system is equal to 1.014 metric horse powers.
1.7.3 Other terms used in this specification or in the equipment data sheets are as defined in the latest
edition of British Standard-5514.
The engine shall be capable of satisfactorily providing an output 10 percent in excess of the
continuous rating defined above, at the same speed for one hour in any period of 12 hours
consecutive running.
The normal power requirement of the engine driven radiator fan or the coolant pump and the
battery charging dynamo shall be clearly stated for the engine which is so equipped.
Unless otherwise specified in the equipment data sheets, the site rating of the engine shall be
worked out considering the durations specified under the latest edition of B.S.-5514 and the
power absorb by all the engine driven ancillaries shall also be deducted.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 185
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
In case the proposed engine model has not been type tested, vendor shall furnish with the offer, a
reference list of its existing industrial installation and at least three of these engines, should have
completed, 5,000 houses of running at site.
4.1.2 Unless otherwise specified in the equipment data sheets, the diesel engine shall be provided with
class A2 governing as per the latest edition of B.S. 5514.
4.1.3 The Cyclic irregularity of the diesel engine for direct coupling to an electric generator, angular
deviation of p73 A.C. generators driven by diesel engine for parallel operation, and the engine
governor speed droop characteristics , shall be restricted to the values specified under the latest
edition of B.S.-5514.
4.1.4 In case diesel engines are required to drive generators in parallel, the governor fuel injection
pumps provided should have identical characteristics and the speed-load curves shall be made
available to the purchasers inspector for his scrutiny and approval prior to load testing. The
vendor shall maintain proper record for such curves to ensure additional diesel engines if required
in future with identical characteristics, could be made available to the purchaser. A set of the said
curves shall also be furnished to the purchaser.
4.1.5 The vendor shall be responsible for carrying out torsion analysis of the dynamic system as
specified in the latest edition of British Standard-5514. The results in the fork of a report shall be
submitted to the purchaser for scrutiny and reference, if desired.
4.1.6 Vendor shall provide the flexible exhaust connection /s to connect the engine exhaust to the
exhaust piping. The required size of the exhaust piping should be clearly specified by the Vendor.
4.1.7 If specified, the common base plate for mounting the diesel engine and the driven equipment as
well as the flexible coupling, shall be supplied by the vendor.
4.1.8 Vendor shall indicate in the bid, the ISO Noise Level rating of the diesel engine with the offered
exhaust silencer/s.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 186
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
aids with diesel engine for quick starting below 4oC of ambient and such aids shall be clearly
detailed out along with the offer.
4.2.2 Where the diesel engine is specified / offered with battery starting arrangement, the starter motor
shall be capable of starting the engine without having to disengage the driven machine with the
help of a clutch. Where the diesel engine is equipped with a dual starter the synchronizing switch
and the corresponding wiring / connection with the starter motor shall be provided by the vendor.
In case of diesel engines driving fire water pumps, besides the engine mounted dynamo and
voltage regulator, the Vendor shall also provide automatic battery charging equipment suitable for
taking power from an alternating current power source and mounted on a free standing type of a
panel.
The battery charger if specified in the equipment data sheet, shall be capable of delivering a
current equal to 100 percent of the 20 hour discharge rate of the battery and also equipped with
charging rate selector device.
4.2.3 Where the diesel engine is specified / offered with compressed air starting, the Vendor shall also
provide the air compressor driven by a diesel engine / electric motor and equipped with necessary
instruments and controls as specified in the equipment data sheets.
The air receiver supplied by the vendor shall provide batteries and battery charging equipment
(see clause B. above) for operating the electrical controls of the diesel engine.
4.2.4 If as specified in the data sheets, the diesel engine is required to start / stop automatically, the
vendor shall provide the necessary controls (automatic-cum-manual) in the engine panel and the
interconnecting wiring and piping from the panel to the engine and starting equipment. A pilot
lamp shall be provided in the line side of the starting equipment circuit to indicate that the
controller is in the automatic position. In the event the engine does not start after three attempts
have been made, the controller shall stop all further cranking and operate the audiovisual alarm.
AD.C. motor driven per lubrication pump with timer suitably interlocked with the starting system
shall be provided by the vendor. Whenever the unit is arrange for automatic shut down, a running
period time set for a specific time interval, and shall be provided.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 187
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4.3.1 When radiator cooled engines are offered, the diesel engine shall be provided with a radiator for
mounting on the common base plate, complete with the suction / blower fan, temperature control
valve and a radiator guard.
4.3.2 Where the engine cooling is achieved by closed circuit cooling water system, the vendor shall
provide the complete jacket water (primary water) circuit, heat exchanger with the make-up tank
and its piping, as well as the raw water (secondary water) circuit including but not limited to the
following:
4.3.2.1 Raw water pump with driver, unless the raw water is required to be obtained from the discharge
of the pump driven by the diesel engine.
4.3.2.2 Raw water piping (prefabricated) and fittings, as specified in the equipment date sheets.
4.3.2.3 Instruments and controls as specified in the equipment data sheets.
4.4.2 The daily service fuel tank shall be equipped with as air breather, shielded level gauge, strainer
and a hand hole of not less than 150 mm diameter, besides the required fuel connections and a
drain plug. The capacity of tank shall be as specified in the equipment data sheets.
4.4.3 The inside surfaces of the fuel tank and the float tank shall be coated with Enamel Red or Black
of I.C.I. or its equivalent and the outside surface to be given two coats of the oil resistant primer
paint. Both the fuel tank and the float tank, shall be hydrostatic tested at a pressure not less than
0.35 kg /Cm2.
5.2 The vendor shall have the responsibility of providing purchasers inspector with all requisite
facilities / equipment for carrying out satisfactory testing.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 188
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5.3 The diesel engines shall be tested in the presence of purchasers inspector in accordance with the
latest edition of B.S. -5514 or any other equivalent standard as agreed to with the purchaser before
the finalization of order.
5.4 The routine load and fuel consumption test shall be of the following duration :
5.5 Unless otherwise specified, 10% overload provision shall be kept while setting the fuel stop for
the site running.
5.6 The hydrostatic test certificates for the heat exchanger / 189ntercooler , fuel tanks and other
pressure vessels shall be furnished to the purchasers inspector for his review and approval at the
time of load testing of the diesel engine.
5.7 The engine control panel/s after assembly and wiring, shall be functionally tested in the presence
of the purchasers inspector.
6.3 All untapped opening shall be provided with 4mm thick metal closures with full rubber gaskets
and bolted by not less than 4 bolts. All connections including those for instruments, instrument
leads, lubricating oil and the like shall be identified with securely attached tags indicating the type
of connection, the instrument or the line description as applicable.
6.4 The equipment shall be crated for domestic / export shipment as specified in the data sheets
considering for storage at job site for at least 6 months. Lifting load-out, and handling instructions
shall be securely attached to the exterior of the largest packing in a well marked weather proof
container. Upright position lifting points, weight (including packing and dimensions shall be
clearly identified with item no., serial no., package no., and the names of the equipment.)
7.0 PROPOSAL:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 189
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
7.1 Proposals shall be accompanied with completely filled in Data Sheets. The vendor shall not use
his own data sheets.
7.2 The proposals must include either a specified statement that all equipment is in accordance with
the purchasers specifications or exceptions, if any, to this general specification including
attachments shall be clearly brought out by the vendor on separate sheets, supported with suitable
reasons thereof for the consideration of the purchaser.
7.3 Additions or exclusions from the scope of supply shall be clearly brought out on separate sheets
giving reasons for such deviations for the purchasers approval.
7.4 Rating (HP) curves for the diesel engine for different duties and their interpretation as per the
applicable standard, shall accompany the proposal.
7.5 The drawings and data as listed under prints with Quote on the vendor data requirement sheet
attached with this specification shall be provided.
7.6 The vendor shall also submit a separate proposal for carrying out supervision of the installation
and commissioning of diesel engine/s offered indicating per item rates, no. of specialists proposed
to be deputed, completion time and a list indicating nature and quantity of consumable/ tools
required and any other terms.
8.0 SCOPE:
8.1 This specification define the requirements of design, manufacture, testing and supply of self
excited emergency generator complete with automatic voltage regulator, control panel, generator
breaker and other accessories as specified in the material requisition.
8.2 Unless otherwise specified the emergency generator shall be supplied complete with
a) Brush less excitation system complete with AVR.
b) Electric panel including control cubicle and associated auxiliary devices, relay panel and
generator breaker battery and charger (unless otherwise specified).
c) Air inlet and outlet for generator cooling (inlet shall be oriented to suit local plant layout).
d) Lifting arrangement for the machine.
e) Foundation frame complete with foundation bolts and base frame.
f) Lube oil system integral with the prime mover lube oil system.
g) Spares for commissioning
h) Spares for two years of operation and maintenance.
Any other part / accessories not specifically mentioned above but considered necessary for safe
and reliable operation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 190
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS : 22534 Designation for type of construction and mounting arrangement of rotating electrical
machines.
IS: 12714 Insulating materials for Electric machinery and apparatus in relation to their thermal
stability service, classification of
Other codes shall be: AS2789, BS4999, BS5000, DIN6271, EGSA101P, IEC34/1, IS4722,
ISO3046/1, ISO8528, NEMAMG1-22, SAEJ1349.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 191
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
In case of sudden application of full load at rated power factor the voltage drop shall not exceed
15% of the rated voltage. The rated voltage shall be restored within 0.5 to 0.8 second depending
on the size of the machine.
10.7 Overloads:
The generator shall be capable of withstanding without injury the effect of a 10% overload for
one hour and 50% overload for one minute.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 192
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 193
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
11.5 All parts and accessories shall be suitable to withstand stresses due to over speed / overload / short
circuit conditions specified.
11.6 Bearings shall be double shielded and relubricated. Grease in the bearing enclosure shall provide
additional lubrication to bearing as well as provide sealing against dust and moisture.
11.7 The generator shall be air cooled unless otherwise agreed generator enclosure shall be as specified
in data sheet.
11.8 The direction of rotation of the rotor of the machine shall be compatible with that of the prime
mover. A clear indication of the direction of rotation shall be given on either end of the machine.
11.9 Space heaters shall be installed within the enclosure, location and max. surface temperature of the
heaters shall be such that no damage can be caused to any insulation. Heaters shall suitable for
operation on a single phase 240V AC supply unless otherwise specified.
A suitable double pole switch shall be mounted on or adjacent to the stators frame or enclosure for
the manual switching off of the heaters.
11.10 Field winding shall have class F insulation with excellent electrical and mechanical properties.
The field winding shall be capable of operating at a field voltage of 125% of rated load field voltage
for at least one minute starting from stabilized temperatures at rated conditions.
11.11 All cabling on the generator set skid shall be in GI cable trays/ conduits. All cables shall be
identified close to their termination point. Double compression type cable glands shall be used for
cable termination.
11.12 A rating plate of corrosion resistant material shall be fixed on the generator frame and shall give the
following information:
a) Manufacturers name.
b) Serial Number, Type and frame reference
c) Rated output in MVA & MW
d) Rated power factor, frequency and voltage
e) Rated stators current and speed in Rev. / Min.
f) Class of insulation
g) Phase rotation (CW or CCW)
h) Customers indent no.
i) Year of manufacture
j) Weight rotor and stators in KG.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 194
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The generator shall be provided with brush less type solid state excitation system with automatic
voltage regulator. The excitation system shall include the automatic voltage regulator, AC exciter
and rotary rectifier. The field of the exciter shall be fed from the stators winding through a
suitable transformer and AVR. AC Voltage generated in the AC exciter shall be rectified by the
rotary rectifier assembly and fed to the main field circuits. The rotor windings of the AC exciter,
the rectifier assemble, main field winding of the generator and other accessories on rotor part
shall be rigidly fastened to the shaft and the connection with different items shall be
anti-loosening type.
The exciter capacity shall be at least 20% more than the maximum requirement at any time. The
exciter winding shall be insulated with class F insulation.
Automatic solid state voltage shall be provided with the following features as a minimum.
- Under frequency protection.
- short circuit protection.
- Manual voltage control switch with adjuster.
- Cross current compensation for parallel operation.
- Voltage build up circuitry.
- Stators current limited.
- Field current limited.
The Current and potential transformers required to feed the AVR from the generator terminal shall be
adequately rated.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 195
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
14.1 The Local generator control panel for the generator set shall comprise of the following unless
otherwise specified in the attached data sheet.
a) Automatic Voltage Regulator.
b) Protection and metering equipments.
c) Indicating instruments.
d) Local breaker for DG set (Siemens / Schneider)
e) Control gear for generator set auxiliaries.
Any other accessory require to make the generator set operational as a package shall be included
in scope of supply. If required the generator control panel shall be split into various functional
sections viz. protection, metering and control, regulation etc.
The generator break shall also be part of the control panel unless otherwise specified. The breaker
rating shall be as specified in the drawing. The protective relays in the Gen. Control panel shall
act to trip this breaker on fault conditions unless otherwise specified. This breaker also serves the
purpose of local isolation.
All motor starters for generator set auxiliaries shall be DOL type.
Unless otherwise specified, the DC control supply required for relays, controls, closing/tripping
of generator breaker, annunciation circuit and for any other purpose shall be met by a DC system
consisting of battery and battery charger of suitable capacity to be supplied by the generator set
manufacturer. The battery shall be sized for two hours load cycle a maximum. Battery charger
shall be of the constant voltage type with current limiting feature and facilities for automatic and
manual, normal and quick charging of batteries. Charger shall be sized for boost charging of
batteries with 10 to 14 hours.
14.2 The panel shall be free standing, metal enclosed, dust and vermin proof type with a hinged door
and having a degree of protection IP 51 as per IS:51 as per IS:2147 unless otherwise specified.
Power and control equipment shall be segregated inside the panel as far as practicable. The
maximum light of the operation handle/switches shall not exceed 1000 mm. and the minimum
height not below 300 mm. All hardware shall be corrosion resistant and bolts, nuts and washers
shall be made of galvanized zinc passivated of cadmium plated high quality steel. Unless
otherwise specified the panel shall be suitable for bottom cable entry. Necessary glands shall be
provided with the panel.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 196
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All auxiliary devices for control, indication, measurement and alarm such as push buttons
control/selector switches, indicating lamps, metering instruments, annunciations etc. shall be
mounted on the front door of the panel. Adequate number of potential free contacts shall be
provided in the control panel for any remote control, monitoring of the generator set.
14.3 All switches shall be load break, heavy duty type. All fuses shall be non-deteriorating HRC
cartridge pressure filled, link type. The contractor shall be air-break type having AC-3 duty
rating. Thermal overload relays shall be three element, positive acting, ambient temperature
compensated type with adjustable setting range and built in protection feature against single
phasing. All indicating instruments shall be moving iron, flush mounting type and of 96 mm x 96
mm square pattern. All control / selector switches shall be rotary back connected type having a
cam-operated contact mechanism with knob type handle. STOP push buttons shall be stay put
type.
14.4 Wiring for power, control and signaling circuits shall be done with PVC insulated copper
conductors having 660 / 1100 V grade insulation. Minimum size of control wires shall be 2.5 mm
ELEMEX type terminals shall be acceptable for wires up to 10mm2 size and for conductors
larger than 10 mm2 bolted type terminals with crimping lugs shall be provided. A minimum of
10% spare terminals shall be provided on each terminal block.
14.5 An adequately sized earth bus shall be provided in the panel for connection to the main earth grid.
All non current carrying metallic parts of the mounted equipments shall be earthed. Doors and
movable parts shall be earthed using flexible copper connections.
14.6 Engraved nameplates shall be provided for all devices mounted on the front of the panel.
Nameplate or polyester adhesive stickers shall be provided for each equipment mounted inside
the panel.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 197
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
shall be provided and lifting points shall be clearly marked on the package. Packing shall be
suitable for storage at site for a minimum period of 6 months.
The HSD tank shall be MS construction, horizontal cylindrical in shape with dished ends.
The tank shall be all welded construction and shall be suitable for storage of HSD up to maximum
temperature of 40 deg. C at atmospheric pressure. Shell thickness of tank shall be 6 mm and thickness of
dished ends 8 mm.
Tanks shall be painted externally and internally to prevent corrosion. The internal surface of the storage
tanks shall be thoroughly cleaned with wires brush / emery paper to remove rust, scale etc and treated
with coat of suitable oil resistant paint. The external surface of the tank shall be thoroughly cleaned with
wire brush / emery paper to remove rust, scale etc. and painted with one coat of zinc chromate primer
followed by two coats of finishing paint (Bitumen based).
All the oil supply pip shall be MS heavy class as per IS 1239 Part 1. All fittings shall be of heavy duty.
Flanges shall be conforming to ASA class 150 weld necks and material to IS 226.
All valves shall be ball type and of body bonnet, gland nut of bronze material with brass or SS ball only.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 198
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The strainers shall be of cast iron body with FM or bronze mesh for fine filtration of the oil.
The HSD supply pipes from HSD yard to respective day oil storage tank shall be laid underground. These
pipes shall be provided with corrosion proof and weather proof treatment.
CLEANILINESS
The area around the vessels shall be kept free from readily ignitable materials, such as weeds and long dry
grass by providing stone pitching.
EARTHING
HSD tank and pipe lines shall be provided with copper earthing and earthed in efficient manner.
NO SMOKING
A permanent notice with letters minimum 5 cms high prohibiting smoking and naked lights shall be fixed
to the fence surrounding the area.
FIRE PROTECTION
The area where tanks, pumping equipment, loading and unloading facilities are provided; shall be well
protected from fire by providing fire hydrants and fire extinguishers. (Shall be part of FFTG tender)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 199
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. STANDARDS
Unless they are at variance with the clauses of this specification, the squirrel cage induction motors and
their components shall comply with the latest applicable Indian standards listed below. Where Indian
standards do not exist, the relevant IEC, British or German (VDE) standards shall apply.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 200
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.4 IS 1271 Insulating materials for electric machinery and apparatus in relation to their
terminal stability in service, classification of.
2.11 IS 4691 Degrees of protection provided by enclosures for routing electrical machinery.
2.16 IS 6381 Constructions and testing of electric apparatus with type of protection e.
2.17 IS 7389 Pressurized enclosure of electrical equipment for use in hazardous area.
2.19 IS 8223 Dimensions and output ratings for foot mounted rotating electrical machines with
frame numbers 355 to 1000.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 201
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.21 IS 8789 Values of performance characteristics for three phase induction motors,
2.23 IS 9628 Specification for three phase induction motors with type of protection n.
2.25 IS 12065 Permissible limits of noise level for rotating electrical machines.
2.27 IS 13529 Guide on effects of unbalanced voltages on the performance of three phase cage
induction motors.
2.28 IS 13555 Guide for selection and application of three induction motors for different types
driven equipment.
3. OPERATING CONDITIONS
3.1 Ambient Conditions - Aurangabad
3.2 Frequency and Voltage Variations
Motors shall be suitable for operating satisfactorily in humid and corrosive atmosphere found in
Refineries, Petrochemical complex, fertilizer and metallurgical plants. Service conditions shall be as
specified in the data sheets. If not specifically mentioned therein, a maximum ambient temperature of 40o
C and an altitude not exceeding 1000 meters above mean sea level, shall be taken into consideration.
Unless otherwise agreed motors shall be designed for continuous, satisfactory operation at rated output
under the following conditions:
a) The terminal voltage differing from its rated value by not more than +/- 6 %, or
b) The frequency differing from its rated value by not more the +/- 3 % or
c) Any combination of (a) and (b).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 202
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Unless otherwise specified motors shall be designed for direct on-line starting. Motors shall be
designed for re-acceleration under full load after a momentary loss of voltage with the residual
voltage being 100% out of phase.
Minimum locked rotor thermal withstand time at rated voltage shall be 10 seconds under cold conditions
and 8 seconds under hot conditions. The starting time of the motor shall be less than the hot thermal
withstand time (time tE in case of increased safety motors) to permit application of conventional bimetal
relays or thermal release against locked rotor and overload conditions.
Unless otherwise specified, all motors shall be suitable for starting under specified load conditions with
75 percent of the rated voltage at the terminals.
Motors shall be designed to allow the minimum number of consecutive starts indicated below:
3.3 Starting
TABLE I
Starts Min no. of consecutive starts
No of consecutive start-ups with initial temp. of 3
the motor at ambient level (cold)
No of consecutive start-ups with initial temp of the 2
motor at full load operating level (hot).
4. PERFORMANCE
4.1 Motors shall be rated for continuous duty (SI) unless otherwise specified.
4.2 The starting current (as % rated current) shall not 600% for motors upto and including 75 KW
and 550% for motors above 75 KW subject to tolerance.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 203
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4.3 Starting torque and minimum torque of the motor shall be compatible with speed torque curve
of the driven equipment under specified operating conditions. For heavy duty drives such as
blowers, crushers etc. high starting torque motors shall be provided. In case where
characteristics of driven equipment are not available while selecting the motor, minimum
starting torque shall be 110% of rated value for motors up to 75KW and shall be 90% of rated
value for motors above 75 KW.
4.4 The pull out torque at the rated voltage shall be not less than 175 percent of the rated load
torque with no negative tolerance. Unless otherwise agreed, the pull out torque shall not
exceed 300 percent of the rated load torque.
In case of motors driving equipment with pulsating loads (e.g. reciprocating compressors) the
minimum value of pull out torque at 75 percent of the rated voltage shall be more than the
peak value of pulsating torque and the current pulsation shall be limited to 40%.
4.5 The minimum value for product of efficiency and power factors for motors rated upto and
including 37 KW shall be as per IS 8789.
The minimum value for product of efficiency and power factors of 2 pol, 4-pole, and 6-pole
motors rated above 37 KW shall be as given below.
Efficiency and power-factor figures for motors having synchronous speeds of 750 r.p.m. and below shall
be as agreed between the purchaser and manufactured.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 204
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The winding shall be tropicalized. The windings shall preferably be vacuum impregnated.
Alternately the windings shall be suitably varnished, baked and treated with epoxy gel for
operating satisfactorily in humid and corrosive atmospheres.
Windings shall be adequately braced to prevent any relative movement during operation and in
this respect, particular care shall be taken for the stator windings of direct-on-line starting squirrel
cage motors. Insulation shall be provided between coils of different phases which lie together.
Core laminations must be capable of withstanding burnout for rewind at 400oC without damage
or loosening.
In case of motors driving equipment with pulsating loads, special attention shall be paid to the
joints of rotor bars and end rings to avoid premature failure due to induced fatigue stresses.
b) Phase Connections
The windings shall be connected in delta. However, for motors rated 2.2 KW and below, star
connection may be accepted.
If star- delta starting is required, this will be specified in the data sheet and the motor windings
shall be fully insulated for delta connection.
c) Winding Terminations
The ends of the windings shall be brought out into a terminal box. They shall be terminated by
means of terminals mounted on an insulating base made of no-hygroscopic and non-flammable
material.
All motors shall be with six terminals and suitable links to connect them in star or in delta except
for motors rated up to and including 202 KW which may be accepted with three terminals.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 205
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All terminals shall be adequately designed. Line terminals shall be thoroughly insulated from the
frame with material resistant to tracking.
The terminal box shall be of sturdy construction and large enough to facilities easy connection of
the cables. Terminal box cover shall be provided with handles to facilitate easy removal.
An adequately sized earth terminal shall be provided in the motor terminal box for termination of
the forth core of specified cables.
The terminal box shall be provided with cables lugs and entries for suitable cables glands
corresponding to the number and size of specified cable. Nickel glands shall be supplied along
with the motor for mentioned cable sizes.
Equipment and accessories provided shall confirm to the hazardous area classification and the
environmental conditions wherever required as specified in the motor data sheet.
Unless otherwise specified the terminals, cable lugs, terminal box, cable entries and cable glands
shall be suitable for the cable sizes as specified below for 2 pole, 4 pole or 6 pole motors:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 206
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
NOTE : Cable sizes motors having synchronous speeds 750 rpm and below shall be as agreed
between the purchase and manufacturer.
Cable Type
Cables used are of 650/1100 V grade aluminium conductor, XLPE insulated, PVC extruded inner
sheath, armoured with overall PVC sheath for conductor cross- sections of 35 mm2 & above.
However, for cables upto & including 16 mm2 cross-section cables used may be with copper or
aluminium conductor as indicated in the data sheet.
The terminal box shall be capable of withstanding internal short circuit conditions without danger
to personnel or plane from the emission if hot gases or flame or due to excessive disfortion or
damage of the terminal enclosure.
Phase Marking
appropriate phase markings as per IS : 4728 shall be provided inside the terminal box. The
marking shall be non-removable and indelible.
Motors for use in hazardous areas (Zone 1 or Zone 2) shall have type of protection Ex(d) Or Ex(e)
or Ex (n) as specified in the data sheet and shall meet the requirements of applicable Indian
standards. Ex(d) type of motors shall have a BIS marking on the name plate.
Motors for outdoor use shall be suitable for installation and satisfactory operation without any
protective shelter or canopy. Motor casing shall be provided with a suitable drain for removal of
condensed moisture except in case of flameproof motors.
Vertical motors with downward shaft shall be provided with fully covering rain canopies. Vertical
motors with upward shaft e.g. on fin-fan coolers, shall be adequately protected, (such as
cowls/canopies) against ingress of water into the enclosure or the bearing housing even when
standing still for long periods of time. Motors designed to handle external thrust from the pump
shall be supplied with a thrust bearing at the non-driving end.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 207
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All internal and external metallic parts which may come into contact with cooling air, shall be of
corrosion resistant material or appropriately treated to resist the corrosive agents which may be
present in the atmosphere. Screws and bolts shall be hot dip galvanized or zing passivated to
protect against corrosion.
Unless otherwise agreed, motors shall have standard frame size for various output ratings as
stipulated in IS : 1231.
Bearing shall be capable of grease injection from outside without removal of covers with motors
in the running conditions. The bearing boxes shall be provided with necessary features to prevent
loss of grease or entry of dust or moisture e.g. labyrinth seal. Where grease nipples are provided,
these shall be associated, where necessary, with appropriately located relief devices which ensure
passage of grease through the bearing. Pre-lubricated sealed bearings may be considered provided
a full guarantee is given for 4 to 5 years of trouble-free service without the necessity of re-
lubrication.
5.5 Rotor
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 208
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The rotor shall be of squirrel cage type, dynamically balanced to provide a low vibration level and
long service life for the bearings. The accepted values of peak to peak vibration amplitudes for a
motor at rated voltage and speed on a machined surface bedplate with the motor leveled and with
a half-key or coupling fitted shall not exceed those given in IS-12075. Die cast aluminium rotors
for motors in hazardous areas may be accepted provided the same are type tested and approved by
competent authorities.
Necessary nuts and spring washers shall be provided for earth connection.
An additional earth terminal shall be provided inside the terminal box as stated in 5.1
6 MISCELLANEOUS ACCESSORIES
6.1 Anti-Condensation Heaters
All motors rated above 30KW shall be provided with 240 V anti-condensation heaters, sized and
located so as to prevent condensation of moisture during shut-down periods. Motors rated 30 KW
and below shall be provided with anti-condensation heaters if specified in the requisition. Motors
meant for humid location such as cooling tower fans, sump pump motors etc. shall be provided
with space heaters irrespective of the motor rating in the motor data sheet. The heaters shall
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 209
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
permanently remain ON when the motor is not in service and as such shall not cause damage to
the windings.
The heater leads shall be brought out to separate terminal box of the same specification and grade
of protection as the main power terminal box excepting that the cable glands provided shall be
suitable for two core 4 sq. mm aluminum conductor, armored cable or 3 x 2.5 sq. mm. copper
conductor armored cable.
A warning label with indelible red inscription shall be provided on the motor to indicate that the
power line and the heater supply shall be isolated before carrying out any work on the motor.
Additional information as stipulated in applicable Indian standards shall be included in the name
plate for motors meant for use in hazardous atmospheres as per IS:13408
7. NOISE LEVEL
The permissible noise level shall not exceed the stipulations laid down in IS 12065.
8. MOTOR VIBRATIONS
Motor vibrations shall be within the limits of IS 12075 unless otherwise specified for the driven
equipment.
9. CRITICAL SPEEDS
The first actual critical speed of stiff rotors shall not be lower than 125% of the synchronous
speed. For flexible rotors this shall be between 60% and 80% of the synchronous speed; the
second actual critical speed shall be above 125% of the synchronous speed.
Internal and external parts of the casing and all metal parts likely to come in contact with the
surrounding air shall be protected with anti-acid paint that will resist the particular ambient
condition.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 210
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
10. PAINTING
The vendor shall give at least 4 weeks advance notice to the purchaser, regarding the date of
testing to enable him or his representative to witness the tests.
The motors shall be tested in accordance with IS: 325 and IS: 4029. Type test including any
specific test to ascertain compliance with these specifications shall be carried out on one sample
from each KW rating and frame size. Routine tests shall be carried out on all motors. In addition,
measurement of vibration and noise level (if desired) shall form a part of route tests.
Test on completely assembled motor shall be carried out in the presence of purchaser or his
representative. The result shall be tabulated and signed by both vendor and purchaser or their
representatives. Though the motors shall be accepted on the basis of the satisfactory result of the
test at the works, it shall not absolve the vendor from liability regarding the proper functioning of
the motor coupled to the driven equipment at site.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 211
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
d) Performance characteristics viz. speed v/s current and speed v/s torque.
e) Thermal withstand curves under hot and cold conditions.
Subsequent to completion of satisfactory inspection and testing, duly signed test certificates, installation,
operation and maintenance manual shall be furnished by the vendor to complete the contractual
obligations.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 212
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Note :
1. The engine HP. should be selected so as to achieve required KW rating to be generated considering
derating of engine due to altitude, temp. Humidity etc.
2. The engine test shall be witnessed by the client's representative.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 213
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ALTERNATOR
DATA SHEET - B
1. Make :
2. Rating : 2 x500KVA
3. Power factor : 0.8
4. Rated voltage : 415 V
5. Voltage regulation : As required
6. Rated current :
7. Speed : 1500 RPM.
8. Frequency : 50 Hz.
9. Field current at rated
output and power factor : to be specified by tenderer
10. Field voltage at rated
output and power factor : to be specified by tenderer
11. Method of excitation and
Regulation : Self
12. Class of insulation : A) Starter - F with temp.rise of Cl.B
B) Rotor - F --- do ------
13. Degree of protection : Screen protected, drip proof.
14. Base plate : The Engine & alternator shall be
mounted and aligned on a common
base plate fabricated from steel.
15. Control Panel AMF : Consist of
i. ACB / MCCB with O/L, E/F and shunt trip releases
ii. On/off indicator.
iii. Auxiliary switch.
iv. Ammeter & Voltmeter with assessors
v. KWH meters with CTs.
vi. Over voltage relay
vii. Under Voltage relay
viii. Reverse & Forward Power relay.
ix. Over & Under frequency Relay
x. KVA meter
xi. Frequency meter.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 214
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 215
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5) DB / MCBs / ELCB /Ind plug socket Schneidder Acti 9, Legrand DX3, Hager
7) Tele / TV wires Cat 3 / RG11 / RG6 Delton / Finolex / Havells / Polycab / RR kable
15) Exhaust Fan with gravity louvers Indoor Usha Lexus or equi of crompton / orient
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 216
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
20) ESE arrestor / Chemical earthing Nimbus - Jeff, Eritech, Indellec , MAP.
23) LT Panel vendors Arrow Engineers, Vivid, Listen lights, Peaton, Adelec, Marine, JJ
industires
The successful tenderer shall have to use the makes from above in consultation with the ARCHITECT and /
or their consultant.
For at par comparison tenderer shall consider 1st listed make as long as possible.
3. SAFETY CODE
1. Suitable scaffolds shall be provided for workmen for all work that cannot safely be done from the
ground, or from the ground, or from solid construction except such short period work as can be done
safely from ladders. When a ladder is used an extra labour shall be engaged for holding the ladder
and if the ladder is used for carrying materials as well suitable footholds and handhold shall be
provided on the Ladder and the ladder shall be given an inclination not steeper than 1/4 to 1 (1/4
horizontal and 1 vertical).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 217
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. Safe means of access shall be provided to all working platform and other working places. Every
ladder shall be securely fixed. No portable single ladder shall be over 9 meters in length. Width
between side rails in a rung ladder shall in no case be less than 30 cm. for ladders upto and including
3 meters in length. For longer ladders this width shall be increased atleast 6 mm. for each additional
30 cm. of length. Uniform step spacing shall not exceed 30 cm.
Adequate precautions shall be taken to prevent danger from electrical equipment. No materials on
any of the sites shall so stacked or placed as to cause danger or inconvenience to any person or the
public. The contractor shall provide all necessary fencing and lightest to protect public from
accidents and shall be bound to bear expenses of defines of every suit, action or other proceedings at
law that may be brought by any person for injury sustained owing to neglect of the above
precautions and to pay any damages and costs which may be awarded in any such suit, action or
proceedings to any such person or which may with the consent of the contractor be paid to
compromise any claim by any such person.
3. Demolition : Before any demolition work is commenced and also during the process of the work:-
a) All roads and open areas adjacent to the work site shall either be closed or suitably protected.
b) No electric cable or apparatus, which is liable to be a source of danger over a cable or apparatus
used by operator, shall remain electrically charged.
c) All practical steps shall be taken to prevent danger to persons employed, from risk or fire or
explosion or flooding. No floor, roof, or other part of a building shall be so overloaded with
debris or any materials as to render it unsafe.
4. All necessary personal safety equipment as considered adequate by the Engineer-in-charge shall be
available for use of persons employed on the site and maintained in a condition suitable for
immediate use; and the contractor shall take adequate steps to ensure proper use of equipment by
those concerned.
a) Those engaged in handling any material, which is injurious to eyes, shall be provided with
protective goggles.
b) Those engaged in welding works shall be provided with welder's protective-shields.
c) Stone breakers shall be provided with protective goggles and protective clothing and seated at
sufficiently safe intervals.
d) The contractor shall not employ male or female labour below the age of 18 years.
5. When work is done near any place where there is risk of drowning, all necessary equipment shall be
provided and kept ready for use and all necessary steps taken for prompt rescue of any person in
danger and adequate provision made for prompt first aid treatment of all injuries likely to be
sustained during the course of the work.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 218
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6. Use of hoisting machines and tackle including their attachments, anchorage and supports shall
confirm to the following:
a) i. These shall be of good mechanical construction, sound material and adequate strength and free
from patent defects and shall be kept in good repair and in good working order.
ii. Every rope used in hoisting or lowering materials or as a means suspension shall be of durable
quality and adequate strength, and free from patent defects.
b) Every crane driver or hoisting appliance operator shall be properly qualified and no person under the
age of 21 years shall be in charge of any hoisting machine including any scaffold winch or give
signals to operator.
c) In case of every hoisting machine and of every chain ring hook, shackle swivel and pulley block
used in hoisting or lowering or as means of suspension, safe working load shall be ascertained by
adequate means. Every hoisting machine and all rear referred to above shall be plainly marked with
safe working load. In case of a hoisting machine having a variable safe working load, each safe
working load and the conditions under which it is applicable shall be clearly indicated. No part of
any machine or of any gear referred to above in this paragraph shall be loaded beyond safe working
load except for the purpose of testing.
d) In case of a departmental machine, safe working load shall be notified by the Engineer-in-charge.
As regards contractor's machines the contractor shall notify safe working load of each machine to
the Engineer-in-charge whenever he brings it to site work and get it verified by the
Engineer-in-charge.
7. Motors gearing, transmission, electric wiring and other dangerous parts of hoisting appliances shall
be provided with efficient safeguards; hoisting appliances shall be provided with such means as will
reduce to the minimum risk of accidental decent of load adequate precautions shall be taken to
reduce to the minimum risk of any part of a suspended load becoming accidentally displaced. When
workers are employed on electrical installations, which are already energized, insulating mats
working apparel such as gloves, sleeves and boots as may be necessary, shall be provided. Workers
shall not wear any rings, watches and carry keys or other materials, which are good conductors of
electricity.
8. All scaffolds, ladders and other safety devices mentioned or described herein shall be maintained in
a safe condition and no scaffold, ladder or equipment shall be altered or removed while it is in use.
Adequate washing facilities shall be provided at or near places of work.
9. These safety provisions shall be brought to the notice of all concerned by display on a notice board
at a prominent place at the work spot. Persons responsible for ensuring compliance with the safety
code shall be named therein by the contractor.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 219
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
10. To ensure effective enforcement of the rules and regulations relating to safety precautions,
arrangements made by the contractor shall be open to inspection by the Engineer-in-charge or his
representatives and the Inspecting Officers.
11. Notwithstanding the above conditions 1 to 14 the contractor is not exempted from the operation of
any other Act or Rule in force.
12. If the height at which the contractor is working is more than 12 feet then the staff should wear
safety helmet and tie himself with softy belt, client/ architect have all right to ask the contractor to
stop wire if the safety condition are not fulfilled.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 220
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 221
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
SOLAR POWER
SCOPE OF WORK, SPECIAL CONDITON AND TECHNICAL SPECIFICATION
This work includes supply, erection testing and commissioning of grid connect solar generating panels,
connecting them with existing electrical distribution system with on GRID TYPE inverters. This work
has to be carried out as per the conditions and technical specifications given below:-
I. The solar panels shall be fitted on the roof top of building. Rates given in schedule of quantity are
inclusive of cost of cables, M.S angles and brackets required for fabrication of the stands of solar
panels.
II. Rates in the quantity schedule for each item are also inclusive of all the incidental material required
for satisfactory completion and commissioning of work.
III. All switch gears should L&T, Siemens, Legrand make only
IV. Complete wiring and cable laying out from solar panels output to main distribution board of the
building should be done by the firm
V. All wiring materials should be fire retardant/ halogen free and low smoke with ISI mark and as per
IS 694 latest version
VI. Apart from attending the break-down calls, the firm shall inspect the system quarterly preventive
maintenance of solar panels and electrical equipment till guarantee period is completed.
VII. Minimum 02 numbers of maintenance free earthing kit as per IS 3043-1987 or latest shall be
provided for each panels i.e. total 05 numbers of earthing kit and its connection to the panels shall
be made without any extra charges.
TECHNICAL SPECIFICATION
1.0 This specification provides the generic requirement for required capacity module, Number of
cells in the module will however depend on the capacity of solar panels.
2.0 This specification covers the general and technical requirements for design, manufacture, testing,
supply, installation & commissioning of Grid connect solar generating system to be provided at the
premises for meeting the lighting and other Electrical load requirements.
3.0 REFERENCE STANDARDS
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 222
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS: 9000 Basic environmental testing procedure for electronic and electrical
items
IEC 61723 Ed1.0 Safety Guidelines for grid connected photovoltaic Systems mounted
on the buildings
IEC 60364-7-712 (1997) Electrical Installations of Buildings Part 7: requirements for special
installations or locations
Section,712: Photovoltaic power supply systems.
The PV array converts the light energy of the sun to DC power. The module mounting structure shall be
used to hold module in position. The DC power shall be converted to AC to supply the AC loads
connected like lights within the premises. Solar panels shall be integrated with the premises power supply
from electricity authority.
DC distribution board shall be provided in between solar array and PCU. It shall have MCCB of suitable
rating for connection and disconnection of array section.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 223
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5.2 Solar panels shall be installed on the shade free roof while the PCU and distribution boards etc.
shall be housed inside the room provided by client
5.3 The statuary approval of local authorities/state electricity distribution company etc. shall be
obtained by Client, if required.
5.4 Client shall provide a shadow free area @ 125 - 150 sq. ft. / KWp of solar array
5.5 Array structure of PV yard and all electrical equipment such as PCU, inverters etc. shall be
grounded properly using adequate number of earthing kits.
5.6 Suitable marking shall be provided on the bus for easy identification.
6.1 The DC output from the modules shall be fed to array junction box & the strings are paralleled at
sub Main & Main junction boxes. Then PCU shall convert DC energy produced by the solar array to AC
energy. The AC power output of the inverter shall be fed to the AC distribution board (metering panel &
isolation panel), which also houses energy meter. The ACDB should be capable of interfacing solar power
with grid power and DG power and to dedicated load also, if desired.
6.3 When the grid voltage and/or frequency goes out of preset range, the inverter shall be
immediately disconnected from the grid. The inverter will reconnect after a pre-determined time when the
grid is back in the range.
6.4 Array to inverter voltage drop shall be less than 5% at the maximum current output of the array.
6.6 For safety reasons, PV inverter system shall be disconnected from the network following the fault
or loss of supply on the power network.
6.7 System Load requirement / power consumption shall vary from place to place.
7.5/6.3/5.3/5.4/8.1KWp capacity arrays shall be installed & Component equipment of the system shall be
sized as per load requirement at the site location.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 224
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.8.1 Individual Solar PV Module should be of capacity 300 Wp (or higher) conforming to IEC:61215 Ed
2 or latest Edition II, IEC : 61730 I:2007, IEC : 61730 II : 2007, manufactured in India in a plant
certified under ISO 9001 : 2008 & ISO 14001 and also type tested by any one of the three accredited test
laboratories under Ministry of New & Renewable Energy, Govt. of India. The Solar PV Module should be
made from not more than 60 Nos. 156X156 mm poly crystalline Silicon Solar Cell connected in series.
6.8.2 SPV modules of similar output with +/- 2% tolerance in single string shall be employed to avoid
array mismatch losses.
6.8.3 SPV module shall contain crystalline high power silicon solar cells. The solar cell shall have
surface anti-reflective coating to help to absorb more light in all weather conditions.
6.8.4 Photo/electrical conversion efficiency of SPV module shall not be less than 14%.
6.8.5 Fill factor of the module shall not be less than 72%.
6.8.6 Each module shall have low iron tempered glass front for strength & superior light transmission.
It shall also have tough multi- layered polymer back sheet for environmental protection against moisture
& provide high voltage electrical insulation. Transmitivity of glass shall be not less than 91%.
6.8.7 Module junction box (weather resistant) shall be designed for long life outdoor operation in harsh
environment.
6.8.8 SPV module shall be highly reliable, light weight and shall have a service life of more than 20
years. SPV modules shall have a limited power loss of not more than 10% of nominal output at the end of
10 years and of not more than 20 % of nominal output at the end of 25 years.
6.8.9 The rated output of any supplied module shall not vary by more than 3-5% from the average
power rating of all ratings.
Each modules, therefore, has to be tested and rating displayed.
6.8.10 Whenever more than one module is required, identical modules shall be used.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 225
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.8.11 It shall perform satisfactorily in relative humidity upto 100% and temperature between 10C and
+85C.
6.8.12 The solar modules shall have suitable encapsulation & sealing arrangements to protect the silicon
cells from the environment. The encapsulation arrangement shall ensure complete moisture proofing (IP
65) for the entire life of solar modules. The terminal block shall be of Nylon 6 material.
6.8.13 The array structure shall be grounded properly using maintenance free earthing kit as per IS:
3043-1987
6.8.14 Marking:
Each module shall carry the following clear and indelible markings:-
- Name, monogram or symbol of manufacturer;
- Type or model number;
- Serial number;
- Polarity of terminals or leads (colour coding is permissible);
- Open circuit voltage
- Operating voltage.
- Maximum system voltage for which the module is suitable;
- Operating current
- Short circuit current
- Date & place of manufacture;.
- Weight of the module
Module shall be tested as per Annexure-A.
6.9.1 The array structure shall be so designed that it will occupy minimum space without scarifying the
output from SPV panels.
6.9.2 The structure shall be designed to allow easy replacement of any module & shall be in line with
the site requirements.
6.9.3 The array structure shall be made of hot dipped galvanized MS angles of suitable size.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 226
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.9.4 The foundation for module mounting structure shall be preferably 1:2:4: PCC construction or any
other combination based on the local site condition requirement for which design details shall be
submitted.
6.9.5 The support structure design & foundation shall be designed to withstand wind speed upto 200
kmph.
6.9.6 The clearance of the lowest part of the module structure & the developed ground level shall not
be less than 500mm.
6.9.7 The module alignment & tilt angle shall be calculated to provide the maximum annual energy
output. This shall be decided based on the location of array installation.
6.9.10 MOVs shall be used at the terminals of array junction boxes for external over voltage protection.
6.9.11 The junction boxes shall have suitable cable entry points fitted with cable glands of appropriate
sizes for both incoming & outgoing cables.
6.9.12 Suitable markings are provided on the bus bar for easy identification & cable ferrules shall be
fitted at the cable termination points for identification.
6.9.13 The Array Junction Box should be preferably have maximum 08 input and 01 output with MOV
and Terminal block.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 227
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.10.1 MPPT Solar charge controller, inverter and associated control and protection devices etc. all shall
be integrated into PCU.
6.10.2 PCU shall provide 3 phase, 41510% V, 50-0 0.5 Hz supply on AC side with THD<3%.
6.10.6 It shall have protection features such as over voltage, short circuit, over temperature etc.
6.10.7 The inverter shall be efficient based on PWM with IGBT/MOSFET reliable power based design.
6.10.8 The PCU shall be capable of complete automatic operation, including wake-up, synchronization
& shut down.
6.10.9 PCU shall have facility to display its basic parameters of the system.
6.10.10 PCU shall be capable to synchronize independently & automatically/to be phase locked with
POWER SUPPLY AUTHORITY grid power line frequency to attain synchronization & export
power generated by the solar panel to POWER SUPPLY AUTHORITY grid in addition to supply
power to the loads.
6.10.11 Built-in with data logging to monitor plant performance through external PC shall be provided.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 228
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.10.15Protections:
Over voltage both at input & output
Over current both at input & output
Over/under grid frequency
Over temperature
Short circuit
Protection against lightening
Surge voltage induced at output due to external source.
6.12 The system description, general/technical requirements etc. are given for general guidance only.
The supplier/manufacturer shall submit the detail design of the complete solar generating system
by using their software to optimize the combination of modules considering the specific location,
isolation, nature of load etc.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 229
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.13.2 Input Grid Line should come from such Distribution Board of client so that Solar Power can feed
the load or feed power to the grid even when grid fails (DG Runs) in day time and Solar Isolation
is available.
6.13.3 The Solar Power should be exported to the bus bar inside ACDB through a LCD Energy Meter.
6.13.4 The Designated Load should be routed through ACDB and an Energy Meter to register the Load
Energy Consumption from Solar & Grid during Week Days and Holiday.
6.13.5 This feature will enable Railways to highlight GREEN POWERED ZONE in a building which
will help them in long Run to Get IGBC NC Rating for that building.
7.2. The SPV panel shall have a provision for directional and angular adjustment of the mounting
structure to get maximum utilization of incident sunlight. It shall be mounted facing south& tilted
to an angle equal to the latitude where being used for optimum performance
7.3 Solar panel supporting structure shall be hot dip galvanized MS frame.
7.4 The supporting structure incorporates corrosion resistant hardwares for all external connections.
8.0 DOCUMENTATION:
The supplier shall provide easy-to-use illustrated installation and operation manual in English and local
language for easy installation and trouble-free usage. Manual shall contain complete system details such
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 230
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
as array lay out, schematic of the system, working principle etc., clear instruction on regular maintenance,
trouble shooting of the solar generating system & emergency shutdown procedure.
One set of essential spares for the system being offered shall be included in the offer & details of t
he offered spares shall be included with the technical bid.
Annexure-A
Modules used in solar panels shall have IEC 61215 Ed 2 or latest compliance certificate. The qualification
testing procedure is defined in IEC 61215 Ed 2 or latest to examine the impact of mechanical, thermal &
electrical stress on power output. The bidder shall submit appropriate type approval certificate for the
offered solar modules from IEC approved laborites.
Method of Testing
10 Visual Inspection:
Each module shall be carefully inspected under an illumination of not less than1000 lux for the following
conditions:
1.1 Racked, bent, misaligned or torn external surfaces.
1.2 Broken / cracked cells
1.3 Faulty interconnections or joints
1.4 Cells touching one another or the frame
1.5 Failure of adhesive bonds; bubbles or de-laminations forming a continuous path
1.6 Between a cell & edge of the module
1.7 Faulty terminations, exposed live electrical parts
1.8 Junction box should have common terminals with suitable bypass diode for preventing hot spot
problem.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 231
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The current-voltage characteristics of the module shall be determined in accordance with IEC 60904-1 at
a specific set of irradiance & temp conditions Performance of PV-Module shall be generally evaluated at
Standard-Test-Conditions (STC) as defined in IEC 60904 standards:
i) Cell temp. of 25 C,
ii) Incident solar irradiance of 1000W/m2,
iii) Spectral distribution of light spectrum with an air mass AM=1.5
3.0 All PV modules supplied shall be accompanied with I-V curves (tested in the manufacturing unit
clearly indicating the serial number, batch number, date and country of origin).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 232
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Salt spray Temp. (+) 35C, RH 95% Duration: 2 hrs IEC-68-2-11 Test Ka
spray and 22 hrs conditioning
No. of Cycle : 01
Wind Pressure equivalent to an air velocity of 200
km/hr
Rain Test as required in the mentioned standards JSS: 55555 (Test No. 12)
Dust Temp : 40C, RH < 50% Duration 1 hr JSS: 55555 (Test No. 14)
Others Electrical Isolation Test Routine test Shall be done at manufacturers place for
every modules offered
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 233
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 234
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 235
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The system, design, materials, equipment and installation shall comply with all other applicable codes &
standards and issued by:-
AHRI 550 Standard for centrifugal or rotary screw water chilling packages.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 236
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Microprocessor-controlled air-cooled chiller utilizing a mono / twin rotor, 2960 rpm (50 HZ), direct drive,
hermetic / semi-hermetic / open, screw compressor using refrigerant HFC-134a or any other ecofriendly
alternative refrigerant.
Chillers using CFC refrigerants such as CFC-11, 12 or 500 shall not be acceptable.
Quality assurance
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 237
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Unit shall be certified with Eurovent / AHRI standard. AHRI 550/590 or EUROVENTANSI / CE PED
Directive
Unit shall be designed, manufactured and tested in a facility with a quality assurance system certified ISO
9001.
Unit shall be manufactured in a facility with an environment management system certified ISO 14001. Unit
shall be tested at the factory.
Unit Cabinet-
- Frame shall be made of U steel beam and protected by three layers of paint.
- The control box plates shall be steel with an oven-baked polyester-paint finish, and be capable of
withstanding a 500-hour salt spray test in accordance with the ASTM B-117 standard (U. S. A.)/
EN (Europe)
Fans-
- Condenser fans shall be direct-driven, die cast aluminium blades, shrouded-axial type, shall be
statically and dynamically balanced, and made of recyclable material with inherent corrosion
resistance. Air shall be discharged vertically upward.
- Fan shall be protected by coated steel wire safety guards.
Compressors-
- Unit shall have semi-hermetic twin-screw, gear-driven compressors with internal muffler and
check valve.
- Each compressor shall be equipped with a discharge shut-off valve.
- Capacity control shall be provided by pilot-operated solenoid valve, capable of reducing unit
capacity to 25% of full load. Compressor shall start in unloaded condition.
- Motor cooling shall be provided by direct liquid injection and protected by internal overload
thermistor.
- Lube oil system shall include pre-filter and internal filter capable of filtration to 3 microns.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 238
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Evaporator-
Unit shall be equipped with a single evaporator-
- Evaporator shall be tested and stamped in accordance with applicable European/American pressure
code PED / ASME for a refrigerant side operating pressure of 1700 kPa (service des Mines units)
and for a maximum water-side pressure of 1000 kPa.
- Shall be mechanically cleanable shell-and-tube type with removable heads.
- Tubes shall be internally-enhanced, seamless-copper type, and shall be rolled into tube sheets.
- Shall be equipped with Victaulic water connections (accessory flanges on request).
- Shell shall be insulated with 19 mm closed-cell, polyvinyl-chloride foam with a maximum K
factor of 0.28.
- Shall incorporate two independent refrigerant circuits.
- Shall have an evaporator drain and vent.
Shall incorporate a refrigerant level control system.
Condenser-
- Coil shall be air-cooled with integral subcooler and shall be constructed of aluminium fins
mechanically bonded to internally fined cu tubes. The tubes are then cleaned, dehydrated & sealed.
- Condenser coils shall be leak tested and shall be pressure tested at 3400 kPa.
- Condenser fan motors shall be 3-phase type with permanently lubricated bearings and Class F
(minimum) insulation. Variable Speed low-temperature Device to control condensation adjusting
the rotational speed with voltage steps (auto-transformer).
- The fins shall have anti-corrosive coating (Acrylic/ Eco coat/ Bly Gold).
Alternatively, celdek pads are acceptable provided that they are mounted on SS sump on all sides of air
intake and are sized adequately to ensure that air quantity does not come down during operation. The
condenser fan should be oversized in this alternative to overcome the pressure drop through the celdek pads
so that efficiency of the chiller does not come down below its specified limit.
Refrigeration Circuits-
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 239
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Refrigeration circuit components shall include oil separators, high and low side pressure relief devices
(according to applicable standards), discharge and liquid line shutoff valves, filter driers, moisture indicating
sight glasses, electronic expansion devices, refrigerant economizers and complete operating charges of both
refrigerant and compressor oil.
2. Diagnostics-
a. Display module shall be capable of displaying set points, system status (including temperatures,
pressures, run time and percent loading), and any alarm or alert conditions.
b. Control Module, in conjunction with the microprocessor, shall be capable of displaying the output
of a full load run test to verify operation of every switch, sensor, fan and compressor before the
chiller is started, & carrying out a diagnosis & preventive maintenance (incorrect water loop, oil
filter dirty etc.)
3. Safeties-
a. Unit shall be equipped with all necessary components and in conjunction with the control system
shall provide the unit with protection against the following -
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 240
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Operating characteristics-
- Unit shall be capable of starting and running at full load at outdoor ambient temperatures from 0C
to 46C.
- Unit shall be capable of starting up with 25C entering fluid temperature to the evaporator.
Electrical characteristics-
- Unit electrical power supply shall enter the unit at one or two locations.
- Unit shall operate on 3-phase power supply without neutral.
- Unit with two compressors shall have a factory-installed, star-delta starter to limit electrical inrush
current.
- Control voltage shall be supplied by a factory-installed transformer.
- Unit shall be supplied with factory-installed electrical disconnect switch / circuit breaker.
Finishing -
Electrical Cabinet Color - as per HVAC Consultant/Project Consultant/ Client. Compressor / Heat
Exchanger Color - as per HVAC Consultant / Project Consultant / Client
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 241
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Solid-state starter shall provide stepless compressor motor accelerating and limit motor in rush current to
150-300% of compressor motor RLA. The starter shall include 6 Silicon Control Rectifiers (SCR) with
integrally mounted bypass contactors to provide SCR by pass once the motor has achieved full voltage and
speed. The starter shall also include automatic acceleration kick circuitry which monitors motor current
subsides and automatically ramps voltage up at a faster rate to eliminate the instability that occurs at the
break away torque point.
- Phase loss
- Phase reversal
- Phase imbalance
- Ground fault
- Shorted SCR
- Current flow while stopped protection
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 242
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
- Ground fault
- Current imbalance fault
- Shorted SCR.
Electrical requirements
The contractor shall supply and install main electrical power line, disconnect switches, circuit breakers,
electrical protection devices per local code requirements and as indicated necessary by the chiller
manufacturer.
The contractor shall wire the water flow switches to the chiller control circuit to ensure that chiller will not
operate until flows are established & maintained as per contractors / consultants specifications.
The contractor shall supply and install electrical wiring and devices required to interface the chiller controls.
Gauges shall be installed in the entering and leaving water lines of the cooler and condenser.
HVAC contractor shall supply & install flow detection devices in chilled water and condenser water piping.
Switches shall make contact when flow is established. Flow switches shall be installed in horizontal runs at
least 5 pipe diameters down-stream from any bend or tee.
4. Insulation
1. Chilled water piping and cooler water boxes shall be installed by the HVAC contractor.
2. Chiller shall be insulated at factory. Final layer of insulation shall be installed at the job site by the
HVAC contractor along with cladding.
3. Chiller insulation shall confirm to UL standard 94, classification 94 HBF and should be suitable for
positive temperature operation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 243
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5. Vibration isolation
Chiller manufacturer shall furnish neoprene isolator pads for mounting equipment on a level
concrete surface.
Start-up
1. The manufacturer shall provide a factory trained representative, employed by the chiller
manufacturer, to perform the start-up, operation and maintenance manual provided by the chiller
manufacturer.
2. After the above services have been performed, the same factory trained, representative shall be
available for a period of class room instruction (not to exceed 4 hours) to instruct the chiller owners
personnel in the proper operation and maintenance of the chiller.
3. Manufacturer shall supply the following literature-
a. Start-up, operation and Maintenance Instructions.
b. Installation Instructions
c. Field Wiring Diagrams
d. Maintenance manual showing maintenance based on calendar basis and hourly basis.
6. Quality Assurance
i. Chiller performance shall be rated in accordance with AHRI Standard 550/590, latest edition.
ii. Equipment and installation shall be in compliance with ANSI/ASHRAE 15 (latest edition).
iii. Cooler and condenser shall be ASME "U" stamped and nameplate certifying compliance with
ASME Section VIII code for unfired pressure vessels.
iv. Centrifugal compressor impellers shall be dynamically balanced and over-speed tested by the
manufacturer at a minimum of 120% design operating speed. Each compressor assembly shall
undergo a mechanical run-in test to verify vibration levels, oil pressures, and temperatures are within
acceptable limits.
Each compressor assembly shall be proof tested at a minimum 204 psig (1406 kPa) and leak tested at
185 psig (1276 kPa) with a tracer gas mixture.
v. Entire chiller assembly shall be proof tested at 204 psig (1406 kPa) and leak tested at 185 psig (1276
kPa) with a tracer gas mixture on the refrigerant side. The water side of each heat exchanger shall be
hydrostatically tested at 1.5 times maximum working pressure.
vi. Prior to shipment, the chiller automated controls test shall be executed to check for proper wiring
and ensure correct controls operation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 244
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.2 PUMPS:
(A) Pumps shall be of Horizontal split-case type and suitable for the given duty points and parallel
operation -
i Type - Inline / End Suction
ii Impeller - Bronze confirming to BS - 1400
iii Shaft - High Tensile Steel
iv Bearings - Ball/Roller
v Pump/Motor Body - CI confirming to IS -210
vi Seal - Mechanical
vii Motor - Sq. cage T.E.F.C.
viii Starter - Star Delta
ix Shaft Sleeve - Bronze LG2
Pumps shall be selected for the rated conditions indicated. Efficiency of the pump proposed to be used shall
be high. Peak efficiency shall be obtained at or near rated conditions. Impellers shall be statically and
dynamically balanced.
(B) Motor rating shown are only tentative and tenderer shall select their drives atlas 5% in excess of the
max. BHP of the pumps.
The following accessories shall be provided where required with each pump besides other standard
accessories -
i. Lubrication fittings and seal packing.
ii. Test and air vent cock.
iii. Drain Cock.
iv. Adequately sealed Terminal box for Aluminium conductor armored cable termination.
(C) The following fittings shall be provided with each pump besides other standard fittings (to be
measured and paid for separately) -
i. Suction and discharge shut-off valve, discharge check valve as specified under respective items.
ii. Suction and discharge pressure gauge not less than 150 mm diameter & of the appropriate rating
with gauge cocks etc.
iii. 25mm GI drain piping up-to the nearest drain point.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 245
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(D) The pump casing should be of closed grain with smooth finishing ensuring minimum frictional
losses and having sufficient strength to withstand the forces due to water flow at all working
conditions.
(E) The impeller should be of Bronze and statically and dynamically balanced to ensure smooth
working without vibration and noise.
(F) Pumps shall be installed as per the manufacturers recommendation. Pump shall be mounted on
floating foundations, which in turn are mounted on vibration isolators. The Contractor shall supply
the floating frame and vibration isolators & concrete foundation.
(G) After complete installation, original paint of the pump shall be retouched and accessories, fittings
and floating foundations frame shall be given two coats of synthetic enamel paints of color specified
in specifications for paining Works / Approved color over a coat of primer.
The pump controller software package should determine the settings for the controller to help in optimizing
the control system by predicting the best staging on and off frequencies.
CONFIGURATION
The pump controller shall form an integral part of the VFD itself and shall not be supplied as a stand-
alone basis. It shall have a 4-line alphanumeric display which is capable of displaying all the operating
parameters. It shall be possible to program the VFD and the pump controller through the same local display
panel. It shall be possible to supply the VFD and pump controller in IP 20 and IP 54 protection. Display key
pad should be detachable and can be mounted on the panel door (up to 3 meter distance)
The pump controller shall be capable of running up to five equally sized pumps in parallel in the best
efficiency pattern.
The VFD-cum-pump controller shall be suitable for adapting itself to any locally available standard sized
pumps and shall be capable of maintaining its best efficiency operating pattern throughout its operating
speed. No de-rating of the pump motor shall be applicable to the offered VFDS.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 246
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
OPERATING MODE
The VPS shall follow a master / slave systems set up, where all pumps and are speed controlled with
Variable Frequency Drives. The pumps shall be of the equal size and should be run at the same speed. One
of the VFD shall act as a master and the other VFDS shall act as slaves which follow the speed of the master
pump. It shall be possible to stage ON and OFF the slave pumps as necessary by the master to match the
system requirement.
The in built pump controller shall calculate the best efficiency operation which optimizes the number of
pumps to achieve the highest system efficiency based on the number of pumps operating in parallel, the
system design head and set point head and the pump curves.
It shall be possible to program a staging and de-staging delay time to prevent fast cycling of the salve
pumps.
PUMP CYCLING
In order to achieve equal operation of the slave pumps, the pumps should be cycled. Whenever a pump has
to be started, the pump with the least hours is switched on. In case a pump has to be switched off, the pump
with the most hours is switched off.
STAGING FREQUENCIES
It shall be possible to program the staging ON / OFF frequencies in the display panel of the VFD which will
determine the frequencies at which the slave pumps should be switched ON & OFF to maintain the best
efficiency operation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 247
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The pump controller shall have a provision to wire a flow switch to the interlock terminals to avoid dry
running of the pumps.
PID CONTROLLER
The system shall be controlled through a fully programmable PID controller which has the capability to
accept the set points in process units (e.g. GPM or m3/h).
The PID controller shall have the provision to accept two remote feedback signals from differential pressure
transmitters, giving an out put of 4-20 mA, located in the chilled water pipe line from the field. It shall be
possible to select the most deviated signal as feedback for controlling the speed of each pump. Each input
signal shall be capable of accepting a different set point. The controller shall be capable of controlling up to
5 pumps in parallel in the master / salve control mode.
It shall be possible to program the proportional, integral and derivative value inputs to the controller for fine
tuning of the PID controller.
DISPLAY
The pump controller VFD shall have a 4-line, back lit, alpha numeric display capable of displaying all
messages in English in text form. It shall have a quick programming menu for faster commissioning and a
detailed menu for fine tuning of the system parameters.
The display panel shall have LED pilot lights for RUN, TRIP and WARNING conditions. The key pad
switches shall be of soft touch type.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 248
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The VFD shall be of the type suitable for operation on a 3 phase, 415 V, 50 Hz input power supply at the
following conditions:
Input supply voltage variations : + 10 %
Input supply frequency variations : 48 52 Hz + 1%
Ambient temperature : 0 - 45o C, without derating.
Maximum relative humidity : 95% non condensing
Vibration : 0.7 G RMS in 3 directions
Minimum efficiency at full load : 97%
The VFDs will be mounted in the open near the AHUs / Pumps in the AHU / Plant room. Hence the
VFDs shall have integrated; factory built metallic enclosures of IP 55 rating, without any de-rating. VFDs
of IP 00 / IP 20 / IP 21 / IP 42 rating enclosures with additional sheet metal enclosures to achieve IP 55
ratings are not permitted.
VFDs shall conform to the recognized international standards like IEC and manufactured according to ISO
9001, BS 5750 part 1 & 2 and shall be UL listed. It shall carry the CE mark on EMC compliance.
The VFD shall be capable of providing a starting torque of 160% for 0.5 sec and an overload torque of 110%
torque for 1 minute.
The VFD shall maintain full output voltage during mains variations of 10% to prevent loss of torque and
speed variations occurring during motor operation.
The VFD shall comply with Electro Magnetic Compatibility (EMC) document IEC/EN 61800 -3 for Radio
Frequency Interference (RFI) control (emission) as an integral part of its design by incorporating RFI filters
to meet C1 -50 Mts, Unrestricted distribution for conducted emission.
For AHU application, VFD should be able to give Clog Filter (by potential free contact) indication as per
the set pressure requirement.
If a temperature / pressure / flow feedback signal is given to the VFD, it shall use its PID controller to
modulate the speed in such a way that the set point of temperature or pressure is accurately maintained. This
should eliminate the requirement of PID loop of BMS or external PID controller.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 249
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Additional PIDs (3 Nos.) are required to control chilled water valves and fresh air damper. This should be an
integral part of the VFD.
The VFD shall be capable of accepting three such feedback signals simultaneously and be able to do a speed
control based on average / sum / difference / minimum / maximum / 3 zone control of the above 2 signals.
This should work in absence of BMS or should not use PID loop of BMS, in case of presence of BMS.
The PID controller shall be capable of programming the set points and incoming signals in any of the
flowing units : RPM, l/s, l/m, l/h, m3/h, m3/s, bar, Pa, kPa, GPM, lb/s, lb/h, CFM, in3/h, inwg, ft wg, PSI,
kW, HP, oC, oF, as required by the application, and be able to display the same while in operation. This
should eliminate the requirement of PID loop of BMS or external PID controller.
In case the VFD detects a broken belt (AHU etc.) or coupling (pumps etc.), it shall display a warning signal
to that effect. There shall be provision to export this warning signal to the BMS system through RS 485,
without any need of I/Os of BMS.
For easier maintenance and to reduce inventory, the VFD shall allow connection of motors one frame size
larger and 4 sizes smaller than its nominal rating.
The VFD shall have the following protective functions: Electronic motor overload, Protection to motor and
VFD against input transients, phase loss, short circuit, under voltage, over voltage, phase imbalance, motor
over temp., phase to phase short circuit or earth fault at motor terminals.
The VFDs shall have internal harmonic filters on the DC bus (on both positive & negative limbs) to reduce
THVD to below 5% as per IEEE standard 519-1992. AC line chokes on the input side are not allowed for
harmonic current control as it will cause voltage drop to the VFD and motor.
The Upeak of the VFD shall be below 1000 Volts (when measured with a cable length of 50 meters) to
prevent damage to motor insulation.
Manufacturer of the VFD shall submit data sheet to verify this requirement in order to permit the usage of
standard motors for the applications specified.
The VFD shall be capable of having an output motor cable length of at least 150 meters (armored cabling)
without any need of additional equipment like output chokes.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 250
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
This is essential for applications like chilled water pumps where the motors are located far away from the
control center.
The VFDs shall incorporate a surge protection circuit as standard to protect the VFD from transients and
spikes in the incoming power supply.
The VFD shall be fully protected from switching a contactor / isolator at the output with out causing tripping
e.g.: for switching on/off the isolators of the AHU / ventilation fans / pumps near the motor and switching
back ON with VFD in on mode.
LED displays are not acceptable, as it is not user friendly. Display of all messages and faults shall be in
English text format. Codes are not acceptable. The display shall show the following operating parameters:
Energy consumed in kWh
Power consumed by motor in kW
Run time of motor in Hours
Current drawn by motor in Amps.
Output frequency in Hz.
Motor speed in RPM
Set point in process units
Feedback in process units
1) It shall be possible to see at least 4 of the above operating parameters in the VFD display,
simultaneously.
2) The VFDs shall have internal galvanic isolation (PELV) to avoid damage to BMS / PLC / DDC
system when interconnected. If PELV is not available, the VFD vendor should offer opto-isolators
for all the inputs and outputs in the VFD.
3) The VFD shall automatically operate at high switching frequency at low speeds and low switching
frequency at high speeds to maintain silent operation of the AHUs at all speeds. The switching
frequency range shall be from 4-14 kHz for VFDs to be installed on AHUs.
4) The VFD shall optimize the magnetizing current on a real time basis based on actual torque
requirement (energy optimization function) to minimize the power consumption compared to
standard variable torque VFDs. VFDs offering fixed settings of V/f ratios are not permitted.
5) The VFD shall have Auto / OFF / Manual switch on the key pad itself. It shall be possible to
manually change the speed of the AHUs from the key pad of the VFD, if required, without the
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 251
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
need of an external potentiometer. In manual mode the speed reference signal shall be from keypad
of VFD and in auto mode, the reference shall be from the remote either BMS or transmitter.
6) The VFD shall have self adjustable ramp times to prevent tripping / VFD damage in case in
appropriate ramp times is set with respect to application requirement.
7) The VFDs shall have the provision to program a minimum and maximum speed of operations,
through the VFD programming itself.
8) In case of a power failure, the VFD shall be capable of automatically restarting after a
programmable time delay, without the need of an operator having switch on the unit.
9) To prevent damage to the VFDs due to pre-rotating fans, the VFD shall have the capability to
detect such spinning fans and adjust its frequency to its spinning speed before it starts controlling
the fan. If the fan is running in the opposite direction, the VFD should brake the fan by sending a
DC current, before starting the fan in the right direction.
10) If the transmitter feedback signal goes below a particular low limit value or goes above a particular
high limit value, the VFD shall give an alarm signal. It shall be possible to transfer this signal to the
BMS system as well.
11) The VFD shall be provided with at least 4 by-pass frequencies with adjustable band width in order
to eliminate resonance in duct work and pipe lines occurring within the motors operating
frequency range.
12) The VFD shall have an auto de-rating facility by operating at a lower capacity in case of a phase
loss or higher ambient temperature so that minimum air conditioning can be maintained. VFDs
that trip on a phase loss or high ambient temperatures are not suitable for this application and hence
not permitted.
13) The VFDs shall have the provision of 4 parameter set ups, which can be activated by the BMS or
by digital inputs.
14) The variable frequency drives (VFD) shall have the provision to integrate into a BMS system,
utilizing a serial communication protocol open protocol or BMS specific protocol - that enables a
full read & write seamless interface between the VFD & BMS. The VFD manufacturer shall be
responsible for technical support to the BMS Vendor in the implementation of a serial interface to
the BMS System. The BMS Vendor shall be responsible for the complete integration and
interoperability of the VFD through the BMS via the serial interface.
15) The VFD shall provide to BMS, via serial communication (by RS-485, 2 wire), access to the
following VFD parameters as a minimum:
Motor current
Motor kW
AHU KWh
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 252
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
16) The VFD shall also be able to provide the following selectable & programmable physical I/Os to
the BMS system
6 Digital inputs (for start, stop, interlock, auto, manual, setup selection etc).
2 Relay outputs ( for reading Auto / Manual status & VFD On / Off indication)
2 Analog input, 4 20 mA ( for single feedback signal to VFD)
3 Analog inputs 0-10V ( for feedbacks, if two feedbacks are taken)
1 Analog Outputs, 4-20 mA (for speed & kW feedback to BMS)
2 Analog Outputs, 0-10V for any other feedback required.
17) VFD shall have inbuilt real time clock for scheduling purpose.
18) If the VFD loses the feedback signal or reference signal in auto mode, the VFD shall be capable of
maintaining the speed at which it is running.
19) If the VFD operates at the minimum speed for a set time, it shall be able to program the VFD to
automatically switch off to save power.
A parameter lock shall be available in the VFD local display panel to prevent unauthorized
resetting of parameters.
Air handling units will be in double skin construction fabricated out of Aluminium Extruded section and 43
mm thick Double skin panels for TFA units & 25 mm thick Double skin panels for Recirculation AHUs/
CSUs.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 253
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Aluminium sections should have double walled rib having a groove for the gasket on the panel side face and
plane surface on internal face. Panel side face should also have additional plane face available for stick on
type gasket to facilitate the fixing of additional gaskets in future if required. Units will be supplied with
round gasket in solid / tubular construction fixed in the groove. Gasket will be made out of PVC / Synthetic
rubber. Extruded section will be having scratchproof anodized finish. The extruded frame structure will be
formed using couplers made out of glass filled nylon, (approx. 30% glass and 70% nylon).
a. AHU Casing-
Double skin panels will be fabricated out of best quality 22G G. I. Powder coated sheet on outer side and
plane 24G G. I. Sheet on inner side. Polyurethane foam of density not less than 36 Kg./Cu. M. will be
sandwiched between inner and outer sheet. The panels will be fixed on Al. Extruded section in such a
manner that fixing screw head does not project on outer face on the panel and sharp end of the screw does
not project inside the unit through double walled rib. The screw hole on panel will be blocked with Nylon
sleeve with cap. The panels shall be 43 mm thick for TFA units & 25 mm thick for Recirculation AHUs/
CSUs. The screw cavity on panel will be blocked with nylon sleeve with cap.
Drain tray will be fabricated out of SS sheet having thickness not less than 1.2mm (18 G). The tray will have
sufficient depth and proper size drain connection. The tray will be insulated from outside with nitrile rubber
foam sheet having thickness not less than 20mm. The rollars in nylon construction will be provided below
the coil for easy removal of coils in the AHUs of areas dealing with powder. Gasket sleeves at chilled water
header outlet will be provided in such a design that the same does not obstruct the pulling of coil at the time
of removal.
Filter section will have rigid construction filter frame fabricated out of GI sheet to house required size filters.
The filters will be in flange type construction having GI casing.
Blower section will consists of extruded sections of proper size to facilitate the mounting of fan and motor
bracket. Direct contact of fan base frame and AHU casing will be eliminated through vibration isolator. Also
flexible connection will be provided at the fan outlet. Suitable panel of blower section will be provided with
hole for cable entry with required arrangement to cover the sharp edge GI sheet. If required, a proper size
box cover will be provided on cable entry location. A provision for earthing will be provided on mainframe
near the cable entry hole.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 254
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Inspection doors at required location will be provided with elegant design hinges made out die cast
Aluminium alloy. Two or more number of hinges per door will be provided depending upon the size of the
door to provide required rigidity to the door panel. One or more number of door handles will be provided
with can type tightening arrangement. The handle and can will be made out of filled nylon having
galvanized iron spindle. The inspection door for blower section will be provided at such a location that the
motor and drive package and fan bearing can be assessed for easily maintenance. An additional guard made
out of GI wire mesh of required strength will be provided at inner side of blower section inspection door. A
limit switch / door switch covered electrical terminal will be provided to facilitate the door inter locking with
fan operation. An inspection glass fitting having the transparent element on both side of the panel with a
common gasket sleeve between two elements will be provided on blower section inspection door to facilitate
inspection of drive package in running condition without opening the inspection door. The inspection doors
of the sections accommodating filters will be of sufficient size to take care of filter removal.
Necessary arrangement with required plastic / nylon fittings will be provided at required locations to
facilitate the mounting of temperature Humidity & pressure sensors as per requirement of BMS vendors.
Properly designed nipples will be provided at required locations to facilitate the connection of manometer
tubes / pressure transmitter.
The entire AHU assembly will be mounted on a common skid fabricated out of HDG MS channel of
required size. The skid will be secured with AHU frame structure through threaded fasteners. The skid will
be duly painted after fabrication with the best quality rust preventive primer followed by two coats of
enamel paint.
All nut bolts, sheet metal screws, fasteners will be Zinc / Nickel plated having resistance against rusting.
b. Cooling Coils-
The cooling coils will be 4/6 Row deep, depending on the utility of the AHU. The cooling coils shall be
fabricated out of copper tube having OD not less than 12.5 mm and Aluminium fins spaced @ 12 fins / inch.
Aluminium fins & copper tubes will have foam bond provided by hydraulic expansion method at the high
pressure above yield point. The capacity of the coils shall be as required under the schedule of equipment.
Velocity of air across coil face shall not exceed 500 FPM for 4 Row coil and 600 FPM for 6 Row coil. All
coils should be AHRI Certified.
c. Fan-
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 255
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Fan wheels and scrolls shall be fabricated from best quality sheet steel. The fan wheels shall be of the
forward / backward curved type enclosed in housing and mounted on a solid shaft.
Fan scrolls shall be fitted with die formed side sheet streamlined inlet and to ensure smooth airflow into the
fan.
d. Filters-
Pre-filters shall be HDPE washable types with 2" thickness with filtration level of 10 micron & efficiency of
90%. The pre-filter section will be located on suction side of the filters. The filters will be IGBC Compliant
and MERV-13 rating.
e. Fan motors-
Fan motors shall be 3 phase, sq. cage, and T.E.F.C. induction type, together with starters, specified in
ELECTRICAL ITEMS separately. The motors shall be capable of high initial starting torque requirement
of fans.
f. Accessories-
Air Handling Units shall be complete with all accessories & shall also include the following- -
a. Shut-off valves, diverting valve, manual air vents, drain valves for cooling coils and drain piping.
b. Vibration eliminators and flexible connections.
c. Supply & return water with dial type thermometer having a range of 0 to 50oC.
d. 100 mm dia. pressure gauges (0 to 6 Kg/Cm) with 10 mm of Needle valve at inlet and outlet.
e. Automatic chilled water flow control with modulating valves.
(All the above specified accessories are quantified in BOQ and shall be measured separately).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 256
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
AHUs such as TFA units, AHU with mixing box having return air ducted shall be provided with thermal
break profile as indicated in schedule of quantities.
i. DAMPER
Dampers shall be opposed blade type. Blades shall be made of double skinned aerofoil aluminum sections
with integral gasket and assembled within a rigid extruded aluminum alloy frame. All linkages and
supporting spindles shall be made of aluminum or nylon, turning in Teflon bushes. Manual dampers shall be
provided with a bakelite knob for locking the damper blades in position. Linkages shall be extended
wherever specified for motorized operation. Damper frames shall be sectionalized to minimize blade
warping. Air leakage through dampers when in the closed position shall not exceed 1.5% of the maximum
design air volume flow rate at the maximum design air total pressure.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 257
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
aluminum grille with approved colour shade. The grilles for the FCU shall be measured separately and paid.
The FCU should be designed in a manner that the drain tray is housed within the body of FCU. The FCU
shall be front accessible type and of draw through type construction.
1.6 FANS
SCOPE
The scope of this section comprises the supply, erection, testing and commissioning of centrifugal, in-line
and propeller type fans and roof mounted units conforming to these Specifications and in accordance with
the requirement of Drawings and Schedule of Quantities.
TYPE
Centrifugal, in-line propeller fans and roof mounted units shall be of the type as indicated on Drawings and
identified in Schedule of Quantities.
CAPACITY
The air-moving capacity of fans shall be as shown on Drawings and in Schedule of Quantities.
CENTRIFUGAL FAN
Centrifugal fan shall be DWDI / SWSI Class I construction arrangement 3 (i.e. bearings on both the sides)
for DWDI fans complete with access door, squirrel-cage induction motor, V-belt drive, belt guard and
vibration isolators, direction of discharge / rotation, and motor position shall be as per the Approved-for-
Construction shop drawings.
a. Housing shall be constructed of 14 gage sheet steel welded construction. It shall be rigidly
reinforced and supported by structural angles. Split casing shall be provided on larger sizes of
fans, however neoprene / asbestos packing should be provided throughout split joints to make it
air-tight.
18-gauge galvanized wire mesh inlet guards of 5 cm sieves shall be provided on both inlets. Housing
shall be provided with standard cleanout door with handles and neoprene gasket. Rotation arrow
shall be clearly marked on the housing.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 258
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
b. Fan Wheel shall be backward-curved non-over loading type. Fan wheel and housing shall be
statically and dynamically balanced. For fans upto 450 mm dia, fan outlet velocity shall not exceed
550 meter/minute and maximum fan speed shall not exceed 1450 rpm. For fans above 450 mm dia,
the outlet velocity be within 700 meter/minute and maximum fan speed shall not exceed 1000 RPM.
High static pressure fan speed shall be as per manufacturer.
d. Bearings: shall be of the sleeve / ball-bearing type mounted directly on the fan housing. Bearings
shall be designed especially for quiet operation and shall be of the self-aligning, oil / grease pack
pillow block type.
e. Motor : Fan motor shall be energy efficient and suitable for 41510% volts, 50 cycles, 3 phase AC
power supply, squirrel-cage, totally enclosed, fan-cooled motor, provided with class F insulation,
and of approved make. Motor name plate horsepower shall exceed brake horsepower by a
minimum of 10%. Motor shall be designed specially for quiet operation and motor speed shall not
exceed 1440 rpm.
The fan and motor combination selected for the particular required performance shall be of the most
efficient (smallest horse power), so that sound level is lowest.
f. Drive to fan shall be provided through belt with adjustable motor sheave and a standard belt guard.
Belts shall be of the oil-resistant type.
g. Vibration Isolation : MS base shall be provided for both fan and motor, built as an integral part,
and shall be mounted on a concrete foundation through resistoflex vibration isolators. The concrete
foundation shall be atleast 15 cm above the finished floor level, or as shown in approved-for-
construction shop drawings.
Fan shall be complete with motor, motor mount, belt driven (or direct driven) and vibration isolation type,
suspension arrangement as per approved for construction shop drawings.
a. Casing : shall be constructed of heavy gage sheet steel. Fan casing, motor mount and straightening
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 259
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
vane shall be of welded steel construction. Motor mounting plate shall be minimum 15 mm thick and
machined to receive motor flange.
An inspection door with handle and neoprene gasket shall be provided. Casing shall have flanged
connection on both ends for ducted applications. Support brackets for ceiling suspension shall be
welded to the casing for connection to hanger bolts. Straightening vanes shall be aerodynamically
designed for maximum efficiency by converting velocity pressure to static pressure potential and
minimizing turbulence. Casing shall be bonderized, primed and finish coated with enamel paint.
b. Rotor : hub and blades shall be cast aluminium or cast steel construction. Blades shall be die-formed
aerofoil shaped for maximum efficiency and shall vary in twist and width from hub to tip to effect
equal air distribution along the blade length. Fan blades mounting on the hub shall be statically
and dynamically balanced. Extended grease leads for external lubrication shall be provided. The fan
pitch control may be manually readjusted at site upon installation, for obtaining actual air flow values,
as specified and quoted.
c. Motor: shall be energy efficient squirrel-cage, totally-enclosed, fan cooled, standard frame, constant
speed, continuous duty, single winding, suitable for 41510% volts, 50 cycles, 3 phase AC power
supply, provided with class `F insulation. Motor shall be specially designed for quiet operation.
The speed of the fans shall not exceed 1000 RPM for fans with impeller diameter above 450 mm,
and 1440 RPM for fans with impeller diameter 450 mm and less.For lowest sound level, fan
shall be selected for maximum efficiency or minimum horsepower. Motor conduit box shall be
mounted on exterior of fan casing, and lead wires from the motor to the conduit box shall be protected
from the air stream by enclosing in a flexible metal conduit.
d. Drive : to fan shall be provided through belt drive with adjustable motor sheave and standard sheet
steel belt guard with vented front for heat dissipation. Belts shall be of oil-resistant type.
e. Vibration Isolation : The assembly of fan and motor shall be suspended from the slab by vibration
isolation suspension of rubber-in.
PROPELLER FAN
Propeller fan shall be direct-driven, three or four blade type, mounted on a steel mounting plate with orifice
ring.
a. Mounting Plate shall be of steel construction, square with streamlined venture inlet (reversed for
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 260
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
supply applications) coated with baked enamel paint. Mounting plate shall be of standard size,
constructed of 12 to 16 gauge sheet steel depending upon the fan size. Orifice ring shall be correctly
formed by spinning or stamping to provide easy passage of air without turbulence and to direct the
air stream.
b. Fan Blades shall be constructed of aluminium or steel. Fan hub shall be of heavy welded steel
construction with blades bolted to the hub. Fan blades and hub assembly shall be statically and
dynamically balanced at the manufacturers works.
c. Shaft shall be of steel, accurately ground and shall be of ample size for the load transmitted and
shall not pass through first critical speed thru the full range of specified fan speeds.
d. Motor shall be standard (easily replaceable) permanent split capacitor or shaded pole for small sizes,
totally enclosed with prelubricated sleeve or ball bearings, designed for quiet operation with a
maximum speed of 1000 rpm for fans 60 cm dia or larger and 1440 rpm for fans 45 cm dia and
smaller. Motors for larger fans shall be suitable for 4156% volts, 50 cycles 3 phase power supply,
and for smaller fans shall be suitable for 220 6% volts, 50 cycles single phasepower supply. Motors
shall be suitable for either horizontal or vertical service as indicated on Drawings and in Schedule
of Quantities.
STRAINERS
Strainer shall be provided at the suction side of pump and chilled water cooling coil. Strainer shall be ISI
Marked and preferable of approved type and shall have fabricated steel bodies of ample strength to
withstand the test pressure specified for the gate valves.
Strainer shall have flanges for connecting the piping. Strainer shall be designed so as to enable blowing out
accumulated dirt & facility of removal & replacement of the screen without disconnecting from main piping.
Each strainer shall be provided with equal size isolating valves so that strainer may be cleaned without
draining the system.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 261
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
PIPING INSTALLATION-
The drawing indicates schematically the size and location of pipes. The Contractor, on the award of the
work, shall prepare detailed working drawing. He must keep in view the specific opening in building and
other structures through which the pipes are designed to pass.
Piping shall be properly supported on or suspended from stands, clamps, hangers etc., as specified &
required. The Contractor shall adequately design all the brackets, saddles, clamps, hangers etc. and shall be
responsible for their structural integrity. The pipe hangers shall provide vibration free installation.
Vertical piping shall be parallel to walls and column lines and shall be straight and plumb. Risers passing
from floor to floor shall be supported at each floor by clamps or collars attached to pipe and with a 10mm
thick rubber pad or any resilient material. Where pipes pass through the terrace floor, suitable flashing shall
be provided to prevent water leakage.
Pipe sleeve of 50 mm larger than the pipe diameter shall be provided wherever pipe pass through walls and
the annular space filled with felt and finished with plaster. Moreover, pipes shall be insulated with Rockwool
and fire retardant sealant wherever it crosses fire barricated walls.
All pipes using screwed fittings shall be accurately out to the required sizes and threaded in accordance with
IS - 554 and burrs removed before laying. Open ends of the piping shall be blocked while working to avoid
entrance of foreign matter. Wherever reducers are to be made in horizontal runs, eccentric reducers shall be
used if the piping is to drain freely. In other locations, concentric reducers may be used.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 262
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Drains shall be provided at all low points in the piping system and shall be of the following sizes with
valves.
Mains Drains
Up to 150mm 25 mm
Over 150 mm 65 mm
Air vents of 15 mm with vent valves of equal size be provided at all high points in the piping system for
venting.
1. Pressure gauges shall be not less than 100 mm dia. & appropriate range and be complete with shut off
valves, stainless steel or CP Brass stem etc.
2. Pressure gauge shall be provided to measure the pressure at the following locations -
i. On inlet and outlet of each chiller,
ii. Suction and discharge of pumps,
3. Care shall be taken to protect pressure gauges during pressure testing.
EXPANSION JOINTS-
Where necessary expansion joints or expansion loops shall be provided to take care of expansion and
contraction of pipes due to variation in temperature.
The unit shall have an internal stainless steel air collector tube with 5/32 diameter perforations and 63%
open area designed to direct accumulated air to the compression tank via an NPT connection at top of unit.
The unit shall have a removable galvanized steel system strainer with 3/16 diameter perforations and a free
area of not less than five times the cross-sectional area of the connecting pipe. A blow down connection
shall be provided to facilitate routine cleaning of the strainer.
Manufacturer to furnish data sheet specifying air collection efficiency and pressure drop at rated flow.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 263
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
TESTING-
All water piping shall be tested to hydrostatic test pressure of at-least two times the maximum operating
pressure, but not less than 10 Kg/cm2 for a period of not less than 24 hours.
All leaks and defects in joints revealed during the testing shall be rectified to the satisfaction of the
Consultant. Piping repaired subsequent to the above pressure shall be retested in the same method as
mentioned above.
CLEANING OF PIPING-
After piping system has been tested and proved tight and leak free, the Contractor shall clean piping system
for dirt, scale, oil, grease, waste & other foreign substances which may have accumulated during process of
installation. Strainer, screens shall be removed, cleaned and replaced after cleaning process & cleaned after
flushing process.
The sample of water which will be used for the chilled water system shall be analyzed by the successful
contractor free of cost. The analysis report shall be submitted to PMC / HVAC Consultant with the
recommendation as to any changes in water input is required.
PAINTING-
After all piping has been installed, tested and run for at-least 2 weeks it shall be coated with primer coat and
synthetic enamel paints of approved shades as per the colour code. The direction of fluid flow in the pipes
shall be visibly marked with arrow.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 264
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
BALANCING VALVE
The balancing valves shall be double regulating type with flow measuring facilities and drain cock. The
pressure measuring nipples to measure differential pressure shall be integral part of the body. All valves
shall be double regulating type with indicator scale from full shut to full open setting position.
The computerized balancing instrument with ISO certificate shall be used to measure the flow rate and DP.
The instrument shall have the capability to store the results of balancing and to log the measured values. The
print outs of the saved data shall form the part of commissioning document.
VALVE ACTUATOR
a) Valve actuator housing shall be rated to IP 44.
b) Actuator shall be driven by a 24 VDC motor, and shall accept 2-10 VDC, 0-10 VDC, 4-20 mA, 3-
point floating or pulse width modulation electric signal and shall include resistor to facilitate any of
these signals.
c) Actuator shall be capable of providing 4-20 mA or 2-10V DC feedback signal to the control system.
d) External LED read-out of current valve position and maximum valve position setting shall be
available.
VALVE HOUSING
a) Housing shall be constructed of forged ASTM (CuZn39Pb2) brass rated at no less than 2500 kPa
static pressure and 120C.
b) Valve housing shall be double union construction with a range of pipe connections available for the
appropriate pipe size.
c) Identification tags shall be available for all valves; tags shall be indelibly marked with part number,
production date and pressure differential range. Tags shall be of aluminium and in size 50mm x
25mm.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 265
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
VALVE ACTUATOR
a) Valve actuator housing shall be rated to IP 44.
b) Actuator shall be driven by a 24 VDC motor, and shall accept 2-10 VDC, 0-10 VDC, 4-20 mA, 3-
point floating or pulse width modulation electric signal and shall include resistor to facilitate any of
these signals.
c) Actuator shall be capable of providing 4-20 mA or 2-10 VDC feedback signal to the control system.
d) Optional fail safe system to power valve to either open or closed position from any position in case
of power failure shall be available.
e) External LED read-out of current valve position and maximum valve position setting shall be
standard.
VALVE HOUSING
a) Housing shall be constructed of Ductile Iron ASTM A536-65T, Class 60-45-18 rated at no less than
4000 kPa static pressure and 120C.
b) Identification tags shall be available for all valves; tags shall be indelibly marked with part number,
production date and pressure differential range. Tags shall be of aluminium and in size 50mm x
25mm.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 266
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1 Balancing valves shall be supplied and installed as shown on the drawings to ensure proper
balancing of waterflows in the hydronic heating and cooling system.
1.2 Flow measurement and balancing shall be possible with an accuracy of 4 to 7% in the normal
measuring range of the valve. (When valve opening position is more than 50%)
1.3 Pressure measuring nipples shall be provided for measuring differential pressure and be integral
with the body and incorporate means for positive leaktight shut-off when not in use.
1.4 Adjustment and presetting of flows shall be made with a digital handwheel.
1.5 The setting shall be lockable with a mechanical stop to allow the valve to be closed but not
opened further than to the preset value.
1.6 For valves in size 10 to 50mm the balancing valves shall offer a facility for draining of water with a
separate hose connection and a stop valve. The optional draining facility shall be capable of being
mounted on or removed from the balancing valve without interruption to the system operation.
1.7 Material and Pressure Ratings
a) Balancing valves with thread connections in sizes from 10 to 50mm shall be made in a
dezincfication resistant copper alloy with Brinell hardness of at least 130 and a body
pressure rating of at least 20 bar (300psi) at 150 degrees C-(AMETAL).
b) Balancing valves with flange connections from 20 to 300mm shall be made in cast iron
equivalent to BS 1452 for a body pressure rating of at least 16 bar 25 bar 150 degrees C.
Valves sized 65mm-300mm shall to be fitted with a pressure balanced cone to reduce
closing torque to allow the valve to be closed and opened easily.
1.8 Balancing valves shall be sized to operate in a normal measuring range of 50% to 100% of full
opening to ensure maximum accuracy.
1.9 All the balancing valves shall be manufactured in accordance ISO9001.
1.10 Certificate of Origin and Certificate of Quality from factory shall be submitted for inspection when
the balancing valves are delivered to site before installation.
1.11 Installation of balancing valves without the specified Certificates shall not be permitted.
1.12 A computerized balancing instrument (CBI) with ISO9000 calibration certificate shall be handed
over after testing & commissioning.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 267
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
A sensor unit which contain a piezo-resisting pressure sensor, one measurement valve and
connection hoses. The measurement valve shall have a safety function which protects the sensor
from high differential pressures.
2.4 In addition to measuring flowrate, differential pressure and temperature, the CBI shall have a
computer programme to provide the following functions:-
- to balance the installation of HVAC system and calculate the necessary valve settings, based
on system measurements
- to store the results of balancing
- to log measured values from a valve (differential pressure, flowrate or temperature)
- to printout saved data in computerized measurement protocol (CMP) consisting of:
i) Name and size of Balancing Valve (BV)
ii) Presetting position of BV
iii) P at BV
iv) flow at BV
v) design flow
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 268
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 269
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
As per SMACNA page no. 1.74, fig. 1-8 Duct Sizes 19 (483 mm) wide and larger which have
more than 10 ft of unbraced panel shall be beaded or cross broken unless ducts will have insulation
covering or acoustical liner. This requirement is applicable to 20 G (1.00 mm) or less and 3 W.G.
(750 Pa) pressure or less. Ducts for 4 W.G. (1000 Pa) or more do not require beads or cross-
breaks. factory fabricated panel type and assembled at site.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 270
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
work in dead or furred down spaces shall be erected in time to occasion no delay to other
contractors work in the building.
15. Where ducts pass through brick or masonry openings, it shall be provided with 25mm thick
appropriate insulation around the duct and totally covered with fire barrier mortar for complete
sealing.
16. All ducts shall be totally free from vibration under all conditions of operation. Whenever ductwork
is connected to fans, air handling units or blower coil units that may cause vibration in the ducts,
ducts shall be provided with a flexible connection, located at the unit discharge.
TESTING
After duct installation, a part of duct section (approximately 5 % of total ductwork) may be selected at
random and tested for leakage. The procedure for leak testing should be followed as per SMACNA-
HVAC Air Duct Leakage Test Manual (First Edition)
Air leakage through dampers when in the closed position shall not exceed 1.5 % of the maximum design
volume flow rate at the maximum design pressure.
Installation
A good quality neoprene rubber of uniform thickness and width shall be used as gasket between flange
joints. The felt shall be fixed by a suitable adhesive and holes made by passing a heated rod through. The
slope of the duct shall be such that the rainwater cannot enter the premise i.e. the slope of duct shall be
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 271
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
towards the outside wall to prevent rainwater entry. Special care shall have to be taken by the contractor in
the time of erection.
i. All ducts shall be rigid and shall be adequately supported and where required with standing seams, tees
or angles of ample size to keep the ducts true to shape and to prevent buckling, vibration or breathing. All
the joints shall be made airtight by soldering & all interior surfaces shall be smooth. Bends shall be made
with radius not less than one half the width of the duct or with properly designed interior curved vanes.
Where metal ducts or sleeves terminate in woodwork, brick or masonry openings, and tight joints shall be
made by means of closely fitting heavy flanged collars.
Ducting over false ceiling shall be supported from the slab above or from beams. In no case a duct is to be
supported from the false ceiling hangers or to be permitted to rest on a hung ceiling.
ii. All holes concrete, masonry etc. made by contractor for fixing supports etc. shall be made good and
restored to original finish by him.
iii.Air handling units and fans shall be connected to duct work by inserting at air inlet and air outlet a
double canvass sleeve. Each sleeve shall be minimum 100 mm long, securely bolted to duct and units.
Each sleeve shall be made smooth and the connecting ductwork rigidly held in line with unit inlet or outlet.
Testing
The entire air distribution system shall be balanced to supply the air quantities as required in various zones
and rooms to maintain the specified room conditions. The final balancing of air quantity through each
grille or diffuser shall be recorded and submitted to the Consultant / Employer for approval.
Painting
Angle iron flanges, stiffeners, hangers and supports shall be painted with two coats primer and those
remaining uncovered further two coats of synthetic
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 272
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.9 DAMPERS-
All dampers shall be of 18 S.W.G. G.I sheets louver dampers of robust construction and tight fitting. The
design, method of handling and control, shall be suitable for the location and service required. Dampers
shall be provided with suitable links, levers and quadrants as required for their proper operation, control or
setting in any desired position. Dampers and their operating devices shall be made robust, easily operable
and accessible through suitable access door. Every damper shall have indication device clearly showing the
damper position at all times. All the bushing will be of brass only.
A fire damper shall be provided between each air handling unit room and the rest area and at crossing of
fire rated walls. The fire dampers shall be confirm to UL-655 and other applicable fire codes. The dampers
shall be operated through either fusible link or solenoid valve.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 273
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The registers shall be suitable for fixing arrangement having concealed screws as approved by Architect.
Linear continuous supply cum return air register shall be extruded aluminium construction with fixed
horizontal bars at 15 Deg. inclination & flange on both sides only (none on top & bottom). The thickness
of the fixed bar louvers shall be minimum 5.5 mm in front and 3.8 mm in rear with rounded edges. Flanges
on the two sides shall be 20 mm/30 mm wide as approved by Architect. The grilles shall be suitable for
concealed fixing. Volume control dampers of extruded aluminium anodized in black colour shall be
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 274
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
provided in supply air duct collars. For fan coil units horizontal fixed bar grilles as described above shall
be provided with flanges on four sides, and the core shall be & suitable for clip fixing, permitting its
removal without disturbing the flanges.
a. All registers shall be selected in consultation with the Architect. Different spaces shall require
horizontal or vertical face bars, and different width of margin frames. These shall be procured only
after obtaining written approval from Architect for each type of register.
b. All registers shall have a soft continuous rubber/foam gasket between the periphery of the register and
the surface on which it has to be mounted. The effective area of the registers for air flow shall not be
less than 66 percent of gross face area.
c. Registers specified with individually adjustable bars shall have adjustable pattern as each grille bar
shall be pivotable to provide pattern with 0 to +45 degree horizontal arc and upto 30 degree deflection
downwards. Bars shall hold deflection settings under all conditions of velocity and pressure.
d. Bar longer than 45 cm shall be reinforced by set-back vertical members of approved thickness.
e. All volume control dampers shall be anodized aluminum in mat black shade.
INSTALLATION-
A good quality felt/expanded polyethylene /rubber of uniform thickness and width shall be used as gasket
between flange joints. The gaskets shall be fixed by a suitable adhesive and holes made by passing a heated
rod through.
1. All ducts shall be rigid and shall be adequately supported and braced where required with standing
seams, tees or angles of ample size to keep the ducts true to shape and to prevent buckling, vibration
or breathing. All the joints shall be made tight and all interior surfaces shall be smooth. Bends shall be
made with radius not less than one half the width of the duct or with properly designed interior curved
vanes where metal ducts or sleeves terminate in woodwork, brick or masonry openings, tight-flanged
collars. Ducting over false ceiling shall be supported from the slab above or from beams. In no case a
duct shall be supported from the false ceiling hangers or to be permitted to rest on a hung ceiling.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 275
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. All holes in concrete, masonry etc. made by contractor for fixing supports etc. shall be made good and
restored to original finish by him.
3. Air handling units and fans shall be connected to duct work by inserting at air inlet and air outlet a
double canvass sleeve. Each sleeve shall be minimum 100mm long, securely bolted to duct and units.
Each sleeve shall be made smooth and the connecting ductwork rigidly held in the line with unit inlet
or outlet.
The entire air distribution system shall be balanced using an anemometer. Measured air quantities at fan
discharge and at various outlets shall be identical to or less/excess than 5 percent in excess of those
specified and quoted. Branch duct adjustments shall be permanently marked after air balancing is
completed so that these can be restored to their correct position if disturbed at any time. Complete air
balance report shall be submitted for scrutiny and approval, and four copies of the approved balance report
shall be provided with completion documents.
PAINTING-
Angle iron flanges, stiffeners, hangers and supports shall be painted with 2 coats of anti rust primer and
those remaining uncovered shall be further painted with 2 coats of synthetic enamel paints of black colour
enamel paints of approved color.
1.12 INSULATION
FOR G.I. DUCTING
SPECIFICATION FOR THERMAL & ACOUSTIC INSULATION
SCOPE
The scope of this section comprises the supply and application of insulation conforming to these
specifications.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 276
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3. Thermal conductivity of elastomeric NITRILE RUBBER shall not exceed 0.034 W/m.K at mean
temperature of 0C
4. Insulation material shall have anti-microbial product, which is EPA (Environmental Protection
Agency), USA approved, as an integral part of insulation that cannot be washed off or worn off.
(NITRILE RUBBER is anti-Microbial polymer)
5. It shall give enhanced level of protection against harmful Microbes such as bacteria, mold, mildew
and fungi and should confirm to following standards: Fungi Resistance ASTM G21 and Bacterial
resistance ASTM G 22 / ASTM 2180.
6. The insulation shall have fire performance such that it passes ASTM E 84 test Method
7. Material should be FM (Factory Mutual), USA approved.
8. Water vapor permeability shall not exceed 1.74 x 10-14 Kg / (m.s.Pa), i.e. Moisture Diffusion
Resistance Factor or value should be minimum 10000.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 277
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The thickness of the NITRILE RUBBER shall be as shown on drawing or identified in the schedule of
quantity. Following installation procedure should be adopted:
1. Duct surfaces shall be cleaned to remove all grease, oil, dirt, etc. prior to carrying out insulation work.
2. Measurement of surface dimensions shall be taken properly to cut closed cell elastomeric rubbers
sheets to size with sufficient allowance in dimension.
3. Material shall be fitted under compression and no stretching of material should be allowed.
4. A thin film of adhesive shall be applied on the back of the insulating material sheet and then on to the
metal surface.
5. When adhesive is tack dry, insulating material sheet shall be placed in position and pressed firmly to
achieve a good bond.
6. All longitudinal and transverse joints shall be sealed as per manufacturer recommendations.
7. The adhesive shall be strictly as recommended by the manufacturer.
8. The detailed Application specifications are as per the manufacturers recommendation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 278
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
For installations exposed to sunlight, after giving 36 hours curing time for the adhesive apply
manufacturers recommended UV/Mechanical Protection. Please refer the separate detailed guidelines on
UV/Mechanical Protection.
The complete chilled water piping including with pipes, bends, flanges, valves, hanger support etc. will be
insulated as per the following -
MATERIAL
1. Insulation material shall be Closed Cell Elastomeric Nitrile Rubber
2. Density of Material shall be between 40 to 60 Kg/m3
3. Thermal conductivity of elastomeric nitrile rubber shall not exceed 0.035 W/mK at an average
temperature of 0C
4. The insulation shall have fire performance such that it passes Class 1 as per BS476 Part 7 for surface
spread of flame as per BS 476 and also pass Fire Propagation requirement as per BS476 Part 6 to meet
the Class O Fire category as per 1991 Building Regulations (England & Wales) and the Building
Standards (Scotland) Regulations 1990
5. Material should be FM (Factory Mutual), USA approved.
6. Water vapor permeability shall not exceed 0.017 Perm inch (2.48 x 10-14 Kg/m.s.Pa), i.e. Moisture
Diffusion Resistance Factor or value should be minimum 7000.
Thickness of the insulation shall be as specified for the individual application
All chilled water, refrigerant and condensate drain pipe shall be insulated in the manner specified herein.
An air gap of 100 mm shall be present between adjacent insulated surfaces carrying chilled water or
refrigerant and also between the insulated surface and the wall to allow natural ventilation without
affecting its external surface coefficient of heat transfer. Before applying insulation, all pipes shall be
brushed and cleaned. All Pipe surfaces shall be free from dirt, dust, mortar, grease, oil, etc. Nitrile Rubber
insulation shall be applied as follows:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 279
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3. Adhesive must be allowed to tack dry and then press surface firmly together starting from butt ends
and working towards centre.
4. Wherever flat sheets shall be used it shall be cut out in correct dimension. All longitudinal and
transverse joints shall be sealed as per manufacturer recommendations.
5. The insulation shall be continuous over the entire run of piping, fittings and valves.
6. All valves, fittings, joints, strainers, etc. in chilled water piping shall be insulated to the same
thickness as specified for the main run of piping and application shall be same as above. Valves
bonnet, yokes and spindles shall be insulated in such a manner as not to cause damage to insulation
when the valve is used or serviced.
The detailed application specifications are as mentioned separately. The manufacturers trained installer
should only be used for installation.
RECOMMENDED ADHESIVE:
In all cases, the manufacturers recommended Adhesive should be used for the specified purpose.
PUMP INSULATION
Chilled water pump shall be insulated to the same thickness as the pipe to which they are connected and
application shall be same as above. Care shall be taken to apply insulation in a manner as to allow the
dismantling of pumps without damaging the insulation.
SHELL INSULATION
The chiller shells shall be factory / site insulated in accordance with the manufacturers standards.
Pipe Supports
All pipe supports should be factory made as detailed specification attached
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 280
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
REFRIGERANT PIPING
LINE TEMP 3 Deg C
DUCT INSULATION
Required Thickness (mm)
Supply Air Duct (Line 23
Temperature 14 Deg. C)
Return Air Duct (Line 8
Temperature 22 Deg. C)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 281
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
DRAIN PIPING
LINE TEMPERATURE 15 Deg.C
REFRIGERANT PIPING
LINE TEMP 3 Deg C
DUCT INSULATION
Required Thickness
(mm)
Supply Air Duct (Line 19
Temperature 14 Deg. C)
Return Air Duct (Line 9
Temperature 22 Deg. C)
Supply Air Duct in 9
Return Air Path (Line
Temp. 14 Deg.C)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 282
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
DRAIN PIPING
LINE TEMPERATURE 15 DegC
Pipe NB (mm) Required Thickness
(mm)
Up to 50 13
REFRIGERANT PIPING
LINE TEMP 3 Deg C
DUCT INSULATION
Required Thickness
(mm)
Supply Air Duct (Line 19
Temperature 14 Deg. C)
Return Air Duct (Line 9
Temperature 22 Deg. C)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 283
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Thickness of the material shall be as specified for the individual application. The insulation should be
installed as per manufacturers recommendation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 284
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Ducts so identified and marked on Drawings and included in Schedule of Quantities shall be provided with
acoustic lining of thermal insulation material for a distance of minimum 5 meters.
Installation Procedure
The inside surface for the ducts shall be covered with adhesive recommended by the manufacturer. Cut
Foamed sheets into required sizes apply adhesive on the foam and stick it to the duct surface
Create fire-resistant seals for pipework using closed-cell, flexible elastomeric insulation with intumescent
effect
Installation:
The intumescent insulation is to be either sleeved over the pipe or slit and sealed using manufacturers
recommended adhesive. Longitudinal seams and butt joints are to be covered with EPDM / NITRILE
RUBBER rubber self-adhesive tape. The gap remaining between the insulation and the wall/ceiling is to be
closed completely using mineral mortar. In lightweight walls, the gap is closed using loose fill within the
wall and filler against the gypsum board (annular gap up to 50 mm).
The length of the intumescent insulation is to be determined depending on the pipe material and diameter
according to manufacturers recommendation as per the standard / test report for the R 90 test.
The Pipe diameters above 89 mm can be insulated with sheets which are additionally fixed with the
binding wire (wound around 6 times per running meter). Binding of wire should be done for tubes as well.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 285
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Installation with zero clearance between the insulated pipes is permitted in the area of penetration is
permitted. In case of chilled water lines condensation aspect should be considered.
Work should be carried out in accordance with relevant R 90 testing standard / test report.
Technical Details:
Temperature Range : -50Cto+105C
Moisture Resistance Factor : 5000
Thermal Conductivity at 0C : 0.035W/(mK)
Thermal Conductivity at 40C : 0.039 W/(m K)
Color: Black
Technical Details:
TemperatureRange:-50Cto+150COverall
Temperature Range: - 50C to +105C If based on EPDM / NITRILE RUBBER Rubber Insulation
Temperature Range: - 50C to +150C If based on EPDM / NITRILE RUBBER Rubber Insulation
Color: Black
Density:205+10gms/sq.meter
Application Notes:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 286
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The covering should be cut to size according the circumference of the insulated pipe please allow an
additional 50mm for the overlap of the covering material. The Overlap shall be securely fixed using
recommended Adhesive.
Spread thin film of recommended on the 50mm overlap and close the seam. When covering fittings, please
consult the manufacturers Application Manual. All fittings have to be covered to the same standards as the
covering of the pipe work. No additional vapor barrier is needed.
For protection against mechanical impact & scratch, a lightweight, Aluminum foil with woven glass fiber
reinforcement covering - with a good resistance to Oil and Chemicals - should be applied. (For Indoor
application only)
Technical Details:
TemperatureRange:-50Cto+150COverall
Temperature Range: - 50C to +105C If based on EPDM / NITRILE RUBBER Rubber Insulation
Temperature Range: - 50C to +150C If based on EPDM / NITRILE RUBBER Rubber Insulation
Dust & Fiber Free
Color : Silver
Application Notes:
The covering should be cut to size according the circumference of the insulated pipe please allow an
additional 50mm for the overlap of the covering material. The Overlap shall be securely fixed using
recommended Adhesive.
Spread thin film of recommended on the 50mm overlap and close the seam. When covering fittings, please
consult the manufacturers Application Manual. All fittings have to be covered to the same standards as the
covering of the pipe work. No additional vapor barrier is needed.
Procedure:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 287
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Note: Mechanical Protection should be applied after 36 hours of Curing of adhesive. It is the minimum
time required for complete curing of adhesive.
The false ceiling shall be insulated with 50 mm thick fiberglass slab of 16 Kg. / Cu. M. density. The
fiberglass slab shall be wrapped in polyethylene bags.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 288
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. The Random Incidence Sound Absorption Coefficient (RISAC); tested as per ISO 354, should be
minimum as per enclosed chart
Material
Insulation material shall be Closed Cell Elastomeric Nitrile Rubber.
Density of Material shall be between 40 to 60 Kg/m3. Thermal conductivity of elastomeric nitrile rubber
shall not exceed 0.037 W/mK at an average temperature of 0 C. The insulation shall have fire
performance such that it passes CLASS 1 as per BS476 Part 7 for surface spread of flame as per BS
Standards & B-1 as per DIN Standards. Water vapor permeability shall not exceed 0.03 Perm inch (2x 10-10
Kgs/m.hr.Pa).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 289
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3. Installation procedures
First the supports for raised floor should be installed on to the floor. Then the floor shall be cleaned
with brush to remove all dirt, cement etc. If floor is uneven it should be made smooth prior to
carrying out insulation work.
Allow an additional 5 mm to the total dimensions while cutting Insulation sheet. Ensure you
measure the cutting dimensions on the top surface of the insulation sheet. This can be identified by
the products markings; they are always on the top surface. This surface is the one you will see
after installation.
All Insulation sheet and floor surfaces shall have all-over adhesive coverage. Adhesive should be
applied on the side that has no product markings and identification printing. This side is the one
that curves inwards.
During installation avoid air bubbles. Always apply pressure on fixing the Insulation sheet, this
action will ensure maximum bond strength.
All cut Insulation sheet edges shall be of a clean cut nature & not cut rough.
All seams and joint shall be sealed with SR 505 adhesive. All seams and joints should have no
more than 10mm of adhesive showing on the outer skin of the finished Insulation sheet installation.
Measurement of surface dimensions shall be taken properly to cut closed cell elastomeric rubbers
sheets to size with sufficient allowance in dimension. Material shall be fitted under compression
and no stretching of material shall be permitted. A thin film of adhesive shall be applied on floor
with brush and then on to the back of the insulating material sheet with brush/small piece of sheet
metal having smooth edges. When adhesive is tack dry, insulating material sheet shall be placed in
position and pressed firmly to achieve a good bond. All joints shall be sealed. SR 505 adhesive of
Pidilite should be used for all cavity floor applications.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 290
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Wherever specified uninsulated flexible duct shall be made of double lamination of Metalized Polyester
film permanently bonded to a coated spring steel wire helix. Duct shall be tear & puncture resistant
construction.
Wherever insulated flexible duct are specified inner core for the same should be made of double lamination
of Metalized Polyester film permanently bonded to a coated spring steel wire helix. Fiber glass insulation
of minimum 14 kg/cu meter density having R-value 4.2 F - Ft - hr/Btu & 32 mm thickness shall be
wrapped over the inner core & covered with strong outer jacket cum vapor barrier made of fiberglass
reinforced Metalized polyester film laminate.
Care must be taken to install all the flexible duct in fully extended position & bends made with adequate
radius as per manufacturer recommended practices.
The lower air blower assembly shall be bolted to the top casing with two (2) bolts on each end allowing
access to the entire lower blower section. The bolts shall be easily removed for inspection or maintenance.
The blower section shall be accessed either by removing the inlet screen, or access panels. The lower air
blower assembly shall contain all mechanical parts and shall be mounted on a rigid base of minimum 14 G
steel. Housing end plates shall be a minimum of 12 G steel. The rigid base and top cover shall be reinforced
by 1.5" x 1.5" angle extending the full length of the unit and shall permit the unit to be supported from both
ends without the need for intermediate support. All internal components shall be of welded construction.
Units shall be supplied with epoxy zinc based two pack jet-black coating.
Units shall be equipped with dynamically balanced forward curved double inlet double width blower
wheels with welded / riveted hubs. The blower wheels, housings and inlet cones shall be constructed of
heavy gauge Aluminium alloy. The blower wheel shall be driven through flexible / rigid couplings to
insure proper alignment of the blower shafts. Each blower wheel shall be supported on either side by heavy
duty deep groove totally sealed permanent lubricated double bearing housed in suitable bearing housing.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 291
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The units shall be supplied with TE motor of suitable rating. Moreover, the unit shall have 2 deep
discharge nozzle equipped with end aerodynamically shaped Aluminium airfoil air direction vane to insure
deflection of entire air stream +/- 20 degree without loss of discharge velocity of opening area.
Sound level measured 5 ft. from the unit in a free field shall be no more than 68 dBA. The average velocity
at the supply end of the curtain shall be between 15 to 17 Mtrs. /Sec. While at the floor level it should be
between 1.5 to 2 Mtrs./Sec.
EVAPORATING UNIT
The cooling coils shall be made of Copper Tubing having extended Aluminium fins. The tubes shall be
mechanically expanded for positive bonding between tubes and fins. The cooling coils circuit
shall be fed with liquid refrigerant through the expansion devise and distributor. The blower shall be
statically and dynamically balanced and designed for silent operation at required airflow rates against
required static pressure. The filters shall be washable synthetic media type arranged for convenient
cleaning and replacement. The drain pan shall be fabricated out of heavy sheet steel, insulated with 1/4
expanded polyethylene sheet. The casing shall be of heavy gauge GI, duly powder coated for weather
protection.
Note: All outdoors units shall be mounted on MS angle frame structure. The MS angle frame
structure shall be painted with epoxy paint. The shade of the paint shall be approved by
approved by the consultants / client.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 292
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Electrically / electronically operated controls shall be provided with all components, auxiliary relays,
capacitors including wiring for controls and interlocking.
Cabinet Construction
The frame and panels shall be constructed of heavy gauge corrosion resistant sheet steel and have modular
construction with aluminium based railing and hinged doors.
Refrigeration Circuit
The refrigeration system shall be of the direct expansion type and each unit must incorporate hermetic
scroll compressors having independent evaporator coil circuit. Compressors will be with necessary
protection devices and valves complete. The system shall include a manual reset HP control and an auto
reset LP switch, filter drier and charging port. A thermal expansion valve, sight glass and filter drier shall
be provided in each circuit. Additionally, the system must be provided with vibration absorbers on the
discharge side of compressor piping to minimize chances of any leaks due to compressor vibrations during
start / stop cycle; this must be in addition to the anti -vibration mounts provided for the compressors.
Evaporator Coil
The evaporator coil shall be constructed of rifled bore copper tubes and louvered aluminium fins, with the
frame and drip tray fabricated from heavy gauge steel. The drip trays must be double angled for
condensate flow and easily removable for cleaning. The cooling coil shall be of suitable rows deep and
designed for high sensible cooling. The distance between the fins should not be less than 1.8 mm and the
face velocity shall not be more than 2.75 m/sec.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 293
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Compressor
The compressor shall be of the high efficiency complaint scroll design with an EER of not less than 11.1
BTUH/watt (COP of not less than 3.25) at ARI rating conditions. Each compressor shall have in-built
overloads, HP and LP controllers and mounted on vibration isolators.
Vibration Absorber
All units must have VIBRATION ABSORBERS in compressor discharge lines to prevent cracks on high
pressure copper pipe lines during start/stop cycle of the compressor.
Units shall be factory balanced in accordance with Section 15071, Mechanical Sound and Vibration
Control.
Only direct drive fans to be provided in offered units and centrifugal fans with belt drive is strictly not
acceptable.
Service Area
The unit shall be serviceable from the front with a maximum service space required of 1 meter.
Electrical Heating
The electric heating elements shall operate at a level not exceeding 60 KW / m. The low watt density
elements shall be of finned tubular nickel plated steel construction.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 294
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The heating circuit shall include dual safety protection through loss of air and high temperature controls.
Humidification
Steam humidifier capacity 5/8 or 10 kg/hr with 3 phase electrodes having function of auto drain and
proportional control for capacity complete with steam supply and water drain hose pipe.
Filtration
Filtration level shall be microvee filters of 90% - 10 microns. Filter clog pressure switch is compulsory.
Electrical Panel
Control cabinet to be NEMA 250; Type 2 enclosure, with grounding lug, combination magnetic starters
with overload relays, circuit breakers and cover interlock, and fusible control circuit transformer.
The electric panel provided for the unit must be equipped with main incoming power isolation switch,
additionally the unit must be provided with under voltage / over voltage / phase reversal / single phasing
protection, all three phase motors must be operated only via 24V coil voltage contactors and MPCBs,
additionally step down transformer must be provided for power supply to the unit controller. The electrical
panel must also be providing with relay block for common alarm.
The condenser frame shall be constructed from heavy duty steel and incorporate a copper tube and
aluminium fin coil.
The coil shall be a maximum of 6 rows deep, with a minimum fin spacing of 2.0 mm with a maximum face
velocity of 3.6 m/s.
The condenser fans shall be direct drive axial type operating at not more than 1440 rpm variable voltage
electric motors. 6 pole 900 rpm fan motors will be used for low noise level applications.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 295
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The condensers must be provided with electronically controlled fan speed controllers, the speed of fans
must be controlled based on temperature sensing of liquid line to ensure compressor constant head
pressure, pressure monitoring electronic switch must be suitable for application up to 12 Amps to take care
of high motor amps.
Control Type
The controls shall be a microprocessor programmable logic controller. The controls shall have separate
indication of operating modes (cooling, heating, humidifying and dehumidifying), alarm conditions
(temperature high, loss of sensor, compressor HP & LP, wet floor, no air flow and low humidifier water).
The display and indication shall be visible on the front without removing any external panels. Local and
remote alarms will be triggered if an alarm condition is reached. Each unit must be provided with large
screen GRAPHICAL DISPLAY and additionally the controller must have feature of DUAL SET POINT
programming.
Alarms
The alarm should operate with the audible signal.
The control should have an auto-restart feature which will return the unit to normal operation resumption of
mains power.
Automatic load / time and alarm sequencing function to be performed by the unit.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 296
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Microprocessor must have output point for ON/OFF of motorized damper and must be suitable to be
integrated with fire point for unit shut off in case receiving signal from fire panel or fire detectors.
The unit controller must have option of {DUAL SET} point for energy saving i.e. customer must have the
option to set two independent set points for the unit based on operational requirements and energy saving
concepts.
Display
In normal operating mode the screen should display unit number, temperature and relative humidity set
points and actual, operating status.
The unit must have a large screen LCD display on controller with user friendly menus and minimum two
level password protections.
RS485 interface port for BMS compatibility with ModBus RTU protocol is required.
The refrigeration piping between indoor and outdoor units will be carried out with good quality soft / hard
copper piping. The complete piping work shall be insulated with formed sections of expanded
polyethylene.
The piping shall be clamped with GI saddles with wooden strips with walls.
a. All refrigerant pipes and fittings shall be hard /soft drawn copper tubes and wrought copper / brass
fittings suitable for connection with silver solder / phos-copper.
b. All joints in copper piping shall be sweat joints using low temperature brazing and / or silver
solder. Before jointing any copper pipe or fittings, its interiors shall be thoroughly cleaned by
passing a clean cloth via wire or cable through its entire length. The piping shall be continuously
kept clean of dirt etc. while constructing the joints. Subsequently, it shall be thoroughly blown out
using carbon dioxide / nitrogen.
c. Refrigerant lines shall be sized to limit pressure drop between the evaporator and condensing unit
to minimum.
d. Sight glass with moisture indicator and removable type combination dryer cum filter with MS
housing and brass wire mesh / punched brass sheet shall be installed in liquid line of the
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 297
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
refrigeration system.
e. Horizontal suction line shall be pitched towards the compressor and no reducers shall be provided
for proper oil return.
f. After the refrigerant piping installation has been completed, the refrigerant piping system shall be
pressure tested using Freon mixed with nitrogen / carbon dioxide at a pressure of 20 kg per sq. cm
(high side) and 10 kg per sq. cm (low side). Pressure shall be maintained in the system for a
minimum of 12 hours. The system shall then be evacuated to a minimum vacuum of 70 cm of
mercury and held for 24 hours. Vacuum shall be checked with a vacuum gage.
g. All refrigeration piping shall be installed strictly as per the instructions and recommendations of air
conditioning equipment manufacturer and the piping design will have to be endorsed by equipment
manufacturer.
h. The Contractor shall make sure that the clamps, brackets, clamp saddles and hangers provided for
pipe supports are adequate. Piping layout shall take due care for expansion and contraction in pipes
and include expansion joints where required.
i. During construction, the contractor shall properly cap all lines, so as to prevent the entrance of
sand, dirt, etc. Each system of piping shall be flushed thoroughly after completion (for the purpose
of removing dirt, grit, sand etc. from the piping and fittings) for as long a time as is required to
thoroughly cleans the system.
j. Wherever pipes pass through the brick or masonry / slab openings, the gaps shall be sealed with fire
barrier caulks.
k. Insulated piping shall be supported in such a manner as not to put undue pressure on the insulation.
20-gauge metal sheet shall be provided between the insulation and the clamp, saddle or roller,
extending at least 15 cm on both sides of the clamp, saddles or roller.
l. All piping work shall be carried out in workmen like manner, causing minimum disturbance to the
existing services, buildings and structure. The entire piping work shall be organized, in
consultation with other agencies work, so that laying of pipes, supports, and pressure testing for
each area shall be carried out in one stretch.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 298
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The following functions shall be carried out by the Building Automation System.
a. Enable and disable each chiller unit through Chiller Manager
b. Monitor status and lockout conditions of each chilling unit and subsequently give an alarm.
c. Monitor the status of each variable frequency inverter upon receiving signal from pump controller
installed in plant room.
d. Switch ON/OFF each pump / chilling unit to maintain the chilled water load demand.
e. Sequence each pump / chilling unit to maintain equal run time.
f. Carry out chilled water temperature reset with respect to chilled water valve position at the AHUs.
g. Monitor status of each of the primary chilled water pumps through a differential pressure switch and
keep a log of run-time.
h. Monitor current drawn and power consumption by each of the chiller compressor and all pumps and
subsequently give an alarm for abnormal consumption.
i. Monitor the common chilled water supply and return temperatures.
j. Monitor the chilled water supply temperature at outlet of each Chiller.
k. Monitor the chilled water supply/return temperature of each CHW circuit.
l. Monitor the common chilled water supply pressure through a pressure transmitter.
m. Monitor the chilled water supply & return header pressure on each of the chilled water circuits.
n. Monitor the energy consumption through BTU meters.
o. Monitor the Chilled water flow rate in return header in each of the chilled water circuits.
p. Monitor flow direction in the chilled water bypass line through flow switches.
q. Monitor the outside air temperature and relative humidity.
r. Monitor any item of plant being switched on a manual basis (i.e. an indication / alarm to come on the
screen, if any equipment is running in manual mode.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 299
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
b. Indicate any unit running in Manual mode and subsequently give an alarm.
c. Carry out monitoring tripping & subsequently give an alarm.
a Maintenance Software
b. Complaint Tracking Software
c. Energy Software
d. Calculation software
e. Document Software
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 300
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
System shall use the BACnet protocol or Lon works for communication to the operator workstation or web
server and for communication between control modules. I/O points, schedules, set point, trends, and alarms
specified in Sequence of Operations shall be BACnet objects.
Performance Standards : System shall conform to the following minimum standards over network
connections. Systems shall be tested using manufacturer's recommended hardware and software for
operator workstation (server and browser for web-based systems).
i. Graphic Display. A graphic with 20 dynamic points shall display with current data within 10 sec.
ii. Graphic Refresh. A graphic with 20 dynamic points shall update with current data within 8 sec. and
shall automatically refresh every 15 sec.
iii. Configuration and Tuning Screens. Screens used for configuring, calibrating, or tuning points, PID
loops, and similar control logic shall automatically refresh within 6 sec.
iv. Object Command. Devices shall react to command of a binary object within 2 sec. Devices shall begin
reacting to command of an analog object within 2 sec.
v. Alarm Response Time. An object that goes into alarm shall be annunciated at the workstation within
15 sec.
vi. Program Execution Frequency. Custom and standard applications shall be capable of running as often
as once every 5 sec. Select execution times consistent with the mechanical process under control.
vii. Performance. Programmable controllers shall be able to completely execute DDC PID control loops at
a frequency adjustable down to once per sec. Select execution times consistent with the mechanical
process under control.
viii. Multiple Alarm Annunciations. Each workstation on the network shall receive alarms within 5 sec of
other workstations.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 301
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ix. Reporting Accuracy. System shall report values with minimum end-to-end accuracy, Control Stability
and Accuracy. Control loops shall maintain measured variable at set point within tolerances.
x. Energy Management through optimization of all connected electrical and mechanical plants.
xi. Prevention of unauthorized or unwanted access.
xii. Suggestive preventive maintenance for all equipment as well as own error diagnosis.
xiii. Building Performance Management
xiv. Optimum support of personnel.
xv. Data Visualization Tool
All DDC controllers shall be connected via an industry standard communication Bus. Communication
between controllers shall be such that, controllers can communicate between themselves without having to
first communicate with the control station. The communication between the different buses shall be
through the system integration units or routers rather than through the control stations. All the system
integration units shall be placed on a Local Area Network (Industry standard open back bone like Ethernet /
BACnet / Lon works etc.). The speed of communication desired between DDC controllers shall be
exceeding 9.6 kbps and on Local Area Network shall be 10 mbps. No proprietary LAN shall be allowed.
Communication
Control products, communication media, connectors, repeaters, hubs, and routers shall comprise a BACnet
internet work. Controller and operator interface communication shall conform to ANSI/ASHRAE Standard
135-2004, BACnet.
Install new wiring and network devices as required to provide a complete and workable control network.
Use existing Ethernet backbone for network segments marked "existing" on project drawings. Project
drawings indicate remote buildings or sites to be connected by a nominal 56,000 baud modem over voice-
grade telephone lines. In each remote location a modem and field device connection shall allow
communication with each controller on the internet work as specified in Paragraph D.
Each controller shall have a communication port for temporary connection to a laptop computer or other
operator interface. Connection shall support memory downloads and other commissioning and
troubleshooting operations.
Internet work operator interface and value passing shall be transparent to internet work architecture.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 302
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
i. An operator interface connected to a controller shall allow the operator to interface with each internet
work controller as if directly connected. Controller information such as data, status, and control
algorithms shall be viewable and editable from each internet work controller.
ii. Inputs, outputs, and control variables used to integrate control strategies across multiple controllers
shall be readable by each controller on the internet work. Program and test all cross-controller links
required to execute control strategies. An authorized operator shall be able to edit cross-controller links
by typing a standard object address or by using a point-and-click interface.
Controllers with real-time clocks shall use the BACnet Time Synchronization service. System shall
automatically synchronize system clocks daily from an operator-designated controller via the internet work.
If applicable, system shall automatically adjust for daylight saving and standard time.
System shall be expandable to at least twice the required input and output objects with additional
controllers, associated devices, and wiring.
System shall support Web services data exchange with any other system that complies with XML
(extensible markup language) and SOAP (simple object access protocol) standards specified by the Web
Services Interoperability Organization (WS-I) Basic Profile 1.0 or higher. Web services support shall as a
minimum be provided at the workstation or web server level and shall enable data to be read from or
written to the system.
i. System shall support Web services read data requests by retrieving requested trend data or point values
(I/O hardware points, analog value software points, or binary value software points) from any system
controller or from the trend history database.
ii. System shall support Web services write data request to each analog and binary object that can be
edited through the system operator interface by downloading a numeric value to the specified object.
iii. For read or write requests, the system shall require user name and password authentication and shall
support SSL (Secure Socket Layer) or equivalent data encryption.
System shall support discovery through a Web services connection or shall provide a tool available through
the Operator Interface that will reveal the path/identifier needed to allow a third party Web services device to
read data from or write data to any object in the system which supports this service.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 303
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Each stand-alone intelligent outstation shall control a maximum of two Air Handling Units and shall be
located adjacent to the air handling unit. These shall also control any other operations on the floor and shall be
sized to suit the operation centers requirement. This shall help in reducing the site electrical installation.
The number of controllers for central plant room equipments shall be decided by the contractor with a
maximum capacity limited to 48 points per controller. Overall, the system shall be provided with 15% spare
capacity, with spare of at least 15% points on each controller. Also, in case of HVAC system, each controller
shall control maximum one chiller and associated chilled water pump.
There shall be one control station located in Chief Engineer Room. The computer shall be sized to cover the
graphic display memory and planning information. The display shall be in the form of dynamic color graphics
and text format with menu driven pop-up windows and help facility.
The following software packages shall be loaded into the system as minimum standard :-
a. Complete system operational software
b. Site specific data manipulation software
c. Active graphics software
d. Energy management system software
e. Alarm indication software
f. Maintenance package (schedule to be developed with Estate Manager).
g. Data Visualization Package
h. Internet Enabled Remote Monitoring Package.
All Web server or workstation and DDC controllers shall communicate using BACnet protocol. Web server
or workstation and control network backbone shall communicate using ISO 8802-3 (Ethernet) Data
Link/Physical layer protocol and BACnet/IP addressing as specified in ANSI/ASHRAE 135-2004,
BACnet. Communication between controllers shall be such that, controllers can communicate between
themselves without having to first communicate with the control station.
Each Building Controller shall reside on or be connected to a BACnet network using ISO 8802-3 (Ethernet)
Data Link/Physical layer protocol and BACnet/IP addressing.
BACnet routing shall be performed by BCs or other BACnet device routers as necessary to connect BCs to
networks of Advanced Application Controllers and Application Specific Controllers.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 304
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Each AAC shall reside on a BACnet network using ISO 8802-3 (Ethernet) Data Link/Physical layer
protocol with BACnet/IP addressing, or it shall reside on a BACnet network using the ARCNET or MS/TP
Data Link/Physical layer protocol.
Each ASC shall reside on a BACnet network using the ARCNET or MS/TP Data Link/Physical layer
protocol.
Each SA shall reside on a BACnet network using the ARCNET or MS/TP Data Link/Physical layer
protocol.
Each SS shall reside on a BACnet network using ISO 8802-3 (Ethernet) Data Link/Physical layer protocol
with BACnet/IP addressing, or it shall reside on a BACnet network using ARCNET or MS/TP Data
Link/Physical layer protocol.
In case of Hot redundant Central Operating Workstation on a peer Bacnet / IP with mirroring function, second
operator workstation would have interoperable feature i.e. incase set points, logic, password are changed in
the second Operator Work Station (OWS) the same would get updated automatically and instantaneously in
the other OWS.
The control station shall consist of the following hardware with all of them suitable for the power supply
voltage of 230 V AC 10% , 50 HZ + 3%.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 305
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
FEATURES DESCRIPTION
Processor Intel Dual Core Pentium D Processor 3.2 GHz with EM 64 Technology
Memory 2GB (2 x1 GB ) dual channel DDR2 533 memory, Up to 8 GB Max. memory
expandable through four DIMM slots
Cache (External) 2 x 2 MB L2 Cache
ROM 512 MB Flash ROM, Can be upgraded from a diskette
Expansion Bus 2nos PCI Express (x1), 4nos 32 bit PCI slots, 33 MHz PCI 2.2 slots, 1-graphics slot
Graphic Accelerator NVIDIA Quadra FX 4400(DVI/VGA)with 512 MB Memory with dual monitor
capable graphics card
Hard Disk 120 GB 7.2K rpm SATA hard disk
Power Supply 375 W switchable/50 Hz with dual power supply provisions
Keyboard Cordless 104 keys window 98 keyboard, PS/2 Compatible
Operating System Supports Windows XP, OS/2 Warp, Windows NT, DOS 6.22
b) Key board : The central station shall be complete with detached 101-keys keyboard which includes
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 306
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
full upper/lower case ASCII key set, a numeric pad, dedicated cursor control pad, and a minimum of 10
programmable functional keys.
c) Color Monitor : The color TFT screen shall be with a minimum 19 inch diagonal no glare screen and
minimum Super VGA resolution of 1024 pixels horizontal, 768 lines vertical and minimum 16 base
colors. The monitor shall be with tilt and swivel facilities.
d) Mouse (Optical): For keyboard less operation, in addition to the enhanced keyboard, a mouse shall also
be provided as an alternative user interface for day to day system operation. 2 Nos. mouse pads shall be
provided for each mouse.
e) Printers: The contractor shall provide printers as specified in the schematic diagram for printing
alarms, operator transactions and reports.
The printer shall be configuring for alarm printing reports, trend log, summary, total logging, recording
alarms and providing system reports etc.
f) The available PCI slots on the PC shall be used only for communication cards and shall not be utilized
for mounting protocol converter cards. If protocol converter cards are used, they shall be external to PC
and separately powered and backed-up by the UPS supply.
The intent of the thin-client architecture is to provide the operator(s) complete access to the BAS system via a
web browser.
The BAS server software must support at least the following server platforms (Windows NT, Sun Solaris
and Linux). The BAS server software shall be developed and tested by the manufacturer of the system
standalone controllers and network controllers/routers. Third party manufactured and developed BAS
software is not acceptable.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 307
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2) The system shall hold a complete set of instructions in the software which can be viewed by the
operator whilst in the operating mode.
3) The system shall provide run simulation of the programs to allow operator verification before
the program is down loaded to the controllers.
4) It shall be possible to assign alarm functions to any programs created as required.
5) Full arithmetic operators shall be available for use in the programs as required e.g.: +, -, /, *, ().
6) Programs shall permit the use of comparison statements such as : =, >, <, =< etc.
7) Programs shall permit logical operators to be used such as : NOT, AND, OR, AND MASK.
8) Direct reference to any point shall be available to obtain its current value. Such references shall be
using standard language such as, ON, OFF, MANUAL, SETPOINT, EXPIRED TIME,
PRIORITY, ALARM.
9) It shall be possible to refer to time and calendar functions directly, so that DATE, TIME, HOUR,
MINUTE functions may be used.
10) It shall be possible to use such mnemonics as ABS (absolute value), SQRT (square root), INT
(integer), MAX (maximum), AVG (average) etc.
11) It shall be possible to set timers so that a timed delay may be introduced before an action is carried
out.
12) In short it should have Trending, Scheduling, Dynamic Graphics, Tree Navigation, Set point,
Operator Configuration, and Global Commands Execution & Parameters Properties as minimum
features.
Following Software shall be provided besides the software for automation system :
Memory Manager - QEMM Version 5.11 (or higher)
Multitasking - Deskview version 2.31 (or higher)
Mouse Driver - Microsoft bus mouse 6.2
Data Base Manager - Latest Version
BAS Server Database
The BAS server software shall utilize a Java DataBase Connectivity (JDBC) compatible database such as:
MS Access, MS SQL 8.0, Oracle 8i or IBM DB2. BAS systems written to Non standard and/or Proprietary
databases are NOT acceptable.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 308
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Management station software shall also be provided all the functions to manage application software
packages within a Preemptive Multitasking environment.
The software shall mainly cover the following third party integrations:
Chiller Integration
Generator Integration
Electricity / Water / Steam / D.G. Sets / VFDs
The above Utility systems shall be incorporated for options such as alarming, automatic demand reduction
and utility bills. It shall have control everything from mission critical cooling to emergency back-up
generators. Special function like unique schedule for a group of rooms shall be provided. Feature like
holiday schedule to save energy in different space of the building.
The request based feature like for example, if the one of the department is going to work on Saturday and
needs air conditioning in the main conference room, the software shall have the feature of occupation
schedule for in the real time calendar, and the system shall do the rest. When the rooms need cooling, they
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 309
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
will send a request to the air handler telling it to start. If the air handler in turn needs cold water from a
chiller, it will send a request to the chiller. With request-based applications, the equipment shall be
controlled by the customers schedule, rather than forcing the customer to adapt to the equipments
schedule.
The system shall have energy management applications, providing features like learning adaptive optimal
start, trim and respond, and demand-based set point adjustment which automatically fine tune the system to
run at peak efficiency.
It shall have networking, trending, alarming, and reporting capabilities,
Boiler Integration:
The software shall be a web based data management tool and consist analysis modules for boiler water and
cooling water systems, respectively. These programs are designed for use in monitoring boiler, steam cycle
and cooling system performance in industrial or utility boiler installations. Boiler, cooling system and other
steam cycle parameters can be trended and alerts can be set for key parameters that are detected to be in an
abnormal condition and diagnoses the reason(s) for many common problems in steam plants and cooling
water systems. It also calculates the total energy consumed v/s the produced energy (Steam) trending with
real time computation of systems efficiency.
Communication Protocol(s)
The native protocol for the BAS server software shall be BACnet over Ethernet DataLink as defined by
ASHRAE standard SPC135. The BAS Server shall support BACnet/IP Annex J to enable communication
through common routers. Proprietary protocols over TCP/IP are NOT acceptable. In addition, the software
shall be able to support concurrent operation of multiple standard and non-standard protocols such as:
SMNP
Lon Works over IP*
* IMPORTANT NOTE: LonMark or Lon Works devices must be networked from LonTalk to an Ethernet
Datalink and IP data structure, using a LonTalk to IP Router like an i1000 Echelon Router. Binding of all
LON devices including Domain, Subnet, Node ID, and the SNVTs structure, in addition to configuration
of all network variables for IP tunneling shall be the responsibility of the LON device supplier. ALL I/O
points listed in the I/O Point Summary shall be configured through the i1000 LON/IP router(s). A copy of
Echelons proprietary LNS Services and LON Manager shall be supplied at no cost to us by the supplier of
the LON devices.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 310
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
v. Display functions:
for the representation and display of operating data and management information in alphanumeric
and graphic form.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 311
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Thin Client web browser GUI shall provide a comprehensive user interface. Using a collection of web
pages, it shall be constructed to feel like a single application, and provide a complete and intuitive
mouse/menu driven operator interface. It shall be possible to navigate through the system using a web
browser to accomplish 2.2 B thru 2.2 J of this specification. The Web Browser GUI shall (as a minimum)
provide a Navigation Pane for navigation, and a Action Pane for display of animated graphics, schedules,
alarms/events, live graphic programs, active graphic set point controls, configuration menus for operator
access, reports, and reporting actions for events.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 312
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 313
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6) Graphic driven point identification and selection shall be provided to allow operator to select a
point by clicking on the graphic symbol representing the point type. Consequently display will
appear to enable the operator to select the desired command.
7) The system shall be capable of running programs in both the foreground mode and background
mode simultaneously. The system running only foreground window while keeping the other
programs dormant in the background window shall not be acceptable as this slows down the
availability of control and essential information to be made available to the operator in the system.
8) Capability of on-line graphics generation shall be a major requirement i.e. the operator shall have
the ability to create new graphics on-site from a menu of symbols.
9) Historical system trouble, fault, false alarms shall be stored on line in the hard disk for trouble
analysis.
10) It shall be possible to define upto 12 functional categories in the plant schematic each of which
shall be removable from the screen individually. This shall allow the operator to delete temporarily
any equipment and have a better overview of the other sections of the system.
11) Maintenance software such as inventory control, work orders shall also be on-line with the
historical data- file for proper maintenance of the system.
12) Data Base Manager shall manage all data on an integrated and non-redundant basis. It shall allow
addition and deletions to the data base without any detriment to the existing data. Cross linkages
shall be provided such that no data required by a software program can be deleted by the operator
until that data has been deleted from its respective programs.
13) Dynamic data such as temperature and humidity values, fans and motor status, alarm point
condition, etc. shall be embedded in the graphics as the sensing location. Points in alarm condition
shall be animated by color changes and flashing/blinking icon, symbol, or value.
14) Commandable points shall be uniquely identified by color and/or discrete symbol and shall be
directly addressable and commandable from the graphic display. It shall not be necessary for an
operator to type in command request or point names. Direct entry of commandable point address or
positioning of the cursor to the point shall cause a display of associated command states for
digitals, the set point value and valid range for analogs. Cursor positioning shall be via a mouse.
15) In order to allow the operators to view graphics in greater detail, zoom /pan display feature shall be
provided to return zoomed/panned graphics to their original status. A return to original feature
shall also be provided. The mouse shall be used to pan in all directions in real time, and to jump,
from any section of the plant schematic directly to another section or to another level.
16) Sample Graphics to be approved during technical submittal.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 314
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The operator panel on a terminal shall provide the primary interface for operator access to the BAS while also
providing a vehicle for the annunciation of alarms and the reporting function. The operator shall have the
option of switching between a text based and graphic based user interface at any time. In particular following
standard functions shall be provided.
1) It shall be possible to carry out the following commands by use of dedicated function keys on the
keyboard and by the mouse :
a. ON - digital points
b. OFF - digital points
c. AUTO - analogue and digital points
d. SET TO VALUE - analogue points
e. ALARM REVIEW
f. POINT TYPE REVIEW
g. POINT GROUP REVIEW
h. HOURS RUN REVIEW / Run Time
i. REVIEW CANCEL
j. GRAPHICS ENABLE
k. HELP
l. ALARM ACKNOWLEDGE
2) It shall be possible to add new points, and reconfigure or modify existing points without taking any
part of the system off-line. It shall be possible to change designation of operator passwords, access
levels, point segregation and auto sign off, designation of backup consoles and printers. It shall also
be possible to add/change descriptors for points, segregation groups and access levels, and action
messages for alarms and trouble condition, system/point enable/disable, input or output value, and
assignment of alarm/warning limits. All additions and modifications shall be on-line programmable
via operators keyboard and then down the line loaded to distributed processing units.
3) It shall be possible to address plant, zones, points etc., using clear language descriptors. Each
individual point may also be identified by a unique alpha-numeric mnemonic address entry. Simple
key names may be assigned to points to allow direct display. These key names shall be fully
operator assignable and depending on how frequently they have to be accessed, they may be as
simple as one, two or three characters or as lengthy as 20 characters.
4) The operator shall be able to access any point on any graphic without going through the penetration
path. Graphics shall be menu-driven. Direct access to graphics shall be menu selectable wherein
the operator may select optionally by entering the name of the graphic system desired or by
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 315
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
This `help facility shall be made available to the operator by use of a dedicated key or a single key click on
the mouse. A minimum help shall be available for every menu item and dialogue box.
The facility shall contain both text and graphics to provide information about the selected function directly.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 316
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The information provided shall be in simple clear language and shall be capable of being added to or modified
by an authorized operator.
4.7 ALARMS
Multiple priority levels of alarm shall be made available. Priority levels shall be deemed Critical Alarms and
Non- critical (general) Alarms. Normally, critical alarms shall take precedence over non-critical alarms, and
high priority over low priority.
Each analog point shall have the following limits defined ; wherever required
When an analog point goes outside the low priority critical alarm limit or Low priority warning limit, a user
defined warning message shall be directed to the appropriate alarm printers at the control station.
The Warning limits shall be used to monitor controllability, not comfort conditions. The alarm limits shall be
used to monitor comfort conditions. When a set point is changed, the warning limits shall automatically
change while the alarm limits shall not change.
When an analog point goes outside any of the limits defined, a user defined alarm message for that level shall
be directed to the appropriate alarm printer and to respective operator workstation. Alarm message shall
require operator acknowledgement.
When a digital point goes into alarm, a user defined alarm message shall be output to the appropriate alarm
printer and to respective control station. Alarm messages shall require operator acknowledgement.
When a point is overridden by operator command from an operator workstation or a local workstation, an
alarm message shall be output to the appropriate alarm printer and to respective operator workstation. Alarm
messages shall require operator acknowledgement.
When a point returns to normal, the event shall be recorded in control stations as Return to Normal.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 317
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Operator workstations shall be capable of displaying a list of all points in alarm for the building in a
single summary. Systems which require the operator to make a separate summary for alarms, shall not be
acceptable.
1 Annunciation: Alarms shall be annunciated at a terminal by an audible tone and icon. Critical
alarms shall be defined by a different color than non-critical alarms.
2 Printing: Alarms shall automatically be printed on the defined alarm printer. The printout shall
contain the address, state or nature of the alarm, alarm priority, and time and date of occurrence.
It shall be possible to route alarms to any printer on the system, in case the allotted printer fails.
Critical alarms like Fire can be sending via sms to responsible person.
3 It shall be possible to produce a user definable full text message to accompany the annunciation of
any alarm. This shall provide further information about the alarm and any action required to be
taken by the operator or indicate that action is automatically programmed in the system. These
messages shall be automatically printed on a designated printer. There shall be no practical limit to
the length of messages created.
4 Acknowledgement: It shall be necessary for all alarms to be acknowledged by an authorized
operator. The facility shall exist for an additional message to be appended at the time of
acknowledgement to provide further information as to any action taken.
Acknowledgement of alarms shall be automatically printed and will indicate the time, date, and any
message generated by the operator.
Alarm silencing shall be by the authorized operators by pressing the silence key.
5 Alarm Clear: When alarms are cleared, then a message shall be produced to indicate the description
of the alarm point, its current state, and the time and date.
6 Disk Records: With the exception of extended text messages, all the information produced above,
alarm annunciation, acknowledgement, and clearing, shall be automatically recorded on the fixed
disk for historical purposes.
7 Alarm Inhibits: It shall be possible to inhibit the transmission of alarms in the following ways:
(i) Operational Inhibits - to allow time for stabilization of power after the normal power is
restored.
(ii) Transient Inhibit - to make allowance for fluttering contacts or allow internal responses.
It shall be possible to select time periods for inhibits (i) and (ii) and may be applied when
entering into alarm, out of alarm, or both.
8 Point lockout: It shall be possible for the operator to lockout the control for any point, to force it to
remain in its current state.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 318
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
A summary showing locked out points shall be available. Systems which require the operator to
make a separate lockout summary shall not be acceptable.
9 Alarm Review: Points in alarm shall be displayed on the operators panel using the alarm review
function.
4.8 LOGGING
1 It shall be possible to log the status or value of system points at regular intervals or on change of
state and store this on hard-disk at any of the central station.
2 It shall be possible to archive this information for future reference.
3 In the case of timed interval logs, it shall be possible to specify a time interval (in minutes) and the
points which are required to be logged.
4 Storage of logged information shall be able to be carried out in any of three ways, single-shot, roll-
over, or split. These are defined as follows: -
4.1 Single-shot: In this type of file, logging shall be carried out only during a pre-defined period for
which the start and finish time and date shall be configurable.
4.2 Roll-over : This file shall be wrap-around where oldest data shall continuously be overwritten by
new incoming data. It shall be possible to configure the number of records to be stored or the
duration in hours, days or months before wrap around occurs.
4.3 Split: Data shall be continuously stored in a series of files automatically created. The change-
over or creation of subsequent files shall be created by splits at user-defined boundaries. The
boundaries shall be able to be defined by duration (hours, days, months) and by time and day of the
first split.
5 Logging files shall be terminal based not system based, to provide true multi-terminal capability.
6 Data produced by the logging facility must be able to be used by standard spread-sheet package for
the analysis of information and the preparation of management report.
7 In addition to the above, the data may be presented in a simplified customized package. The
package should have the following features as minimum:
Charting of logged data on disk in line graph, bar graph or pie format.
Presentation of logged data on disk in tabular format.
Charting of dynamic data (up to 8 points) in real time.
Presentation of dynamic data in tabular format in real time.
Selection of Auto/ manual scaling of X(time) axis and Y(variable) axis.
Tailoring of charts by selection of line width and background colors.
Optional grid overlays (full and dotted lines).
Selection of horizontal/ vertical arrangement of windows or a `cascade presentation.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 319
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Multiple Windows.
Printing of completed presentations.
User configurable data selections.
Optional display of point titles.
Selection of primary or secondary values for display.
Presentation of both analog and digital values (ON/OFF etc.).
1. Point summary reports may be requested at any penetration level. Point summary reports shall
include the current value/status and condition, point descriptors and all relevant information.
Point summary reports shall be selectable for all points.
All reports shall be capable of being scheduled to run at a specific time and/or interval via an
operator function supported by necessary data entry templates and interactive prompts.
2. As a minimum, the system shall provide the following summaries:
Point summary
Alarm summary
Limits summary
Lockout summary
Off-line summary
Override summary
Utility summary
Point status (alarm, locked out, off-line, override)
Point name
Point status/value (automatically updating)
Engineering units.
The alarm summary shall list all points in alarm in the selected system. It shall be possible to print on a
single summary, all points in alarm in the building. As a minimum, the alarm summary shall include :
Point name
Point status/value (when alarm occurred)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 320
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Alarm message
Date and time of alarm occurrence
The limits summary shall list all the alarm limits, and warning limits.
The lockout summary shall display points in the selected system which have either reporting or triggering
locked out.
The off-line summary shall display points in the selected system which have lost communication with the
system.
The override summary shall display points in the selected system which have been overridden by operator
command.
The utility profile shall display the total consumption, measured peak for the current period and the
previous period.
3. Trend historical reports shall allow the operator to randomly select logical group of points to be
recorded at selectable time intervals. It shall be possible to assign up to ten variables to each trend
report. The format, headers, footers, and calculations shall be selectable by the operator. The trend
report shall be stored to disk and shall be subsequently capable of being displayed, and/or printed
by the operator.
4. Dynamic trends shall provide upto eight points and show real time activity of the associated
points. This information shall be printed and/or displayed in numeric, bar chart, curve plot, pie
chart, etc., as selected by the operator. Graphic plots shall allow a unique color for each point.
Sample interval of points selected for dynamic trend shall be user selectable. 3- Dimensional
dynamic trending must be provided in the system.
5 Alarm and run time reports shall be automatically issued to assigned printers immediately upon
occurrence, and shall consist of the point with engineering unit, the time, and the date, and the
alarm message.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 321
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. All alarm and return to normal activity shall automatically be routed to history files. Alarms and
return-to-normal shall include warning and alarm threshold violations with no-response, trouble,
run time exceeded, demand alarms, and command failures. It shall be possible to request a report
by specifying points of interest, the time window of interest, and the type of alarms of interest.
Locking out or disabling of points shall also be historically stored and output in the all- type
reports.
2. Operator shall be able to select, via the CRT terminal keyboard, those analog and digital inputs and
outputs to be stored and the interval at which samples are taken.
3. It shall be possible to access software packages such as MS-Office / MS-Excel or similar, so that
the operator may format display or printouts in the form of :
(a) Spread sheets.
(b) Bar charts.
(c) Curve plots.
4. History files shall be the source data for stored trend reports to be used for records and system
analysis. Operator shall be able to select specific points to be trended, the time period of the trend,
the sample interval, and time at which the report is printed. Trend output format shall be as
specified for trend logs (shaded, unshaded etc)
4.11 UTILIIES :
The Central Station personal computer (P.C.) shall be provided with the following menu selected graphic
system utilities or desktop application packages .
The system provided must be capable of running standard software packages concurrently with the real time
system. System should be capable of supporting third party software packages like spreadsheet, word
processing etc.
1. The base system software shall include a CRT windowing feature to allow the operator to
monitor the real time system and use the third party software simultaneously.
2. All third party software packages identified shall have access to the system historical data base.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 322
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 323
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Regular days
Special days
Holidays
8) The system shall accept one-time schedules to accommodate overtime usage.
One-time schedules shall be automatically deleted from the system after execution.
The system shall allow one-time schedules to be programmed up to one year in advance.
9) After recovery from a power failure, the system shall determine any time scheduled commands
which should have been issued during the period that the power was off. These commands shall
automatically be issued.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 324
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2) The operator shall be able to select points and define any interval on which samples may be taken.
3) For long term storage of samples, trend data shall automatically be updated.
4) A report shall be available listing all points being trended. The report shall display:
Trend status
Point name
Parameter being trended
Display units
Sample interval
Number of samples taken.
5) A trend for a point shall be able to be started either by operator command or according to a time
scheduled command. A trend for a point will end as a result of an operator command, time
scheduled command or when the required number of samples have been collected.
6) Trend samples shall be displayed in either tabular or graphical format. A minimum of eight trended
points shall be able to be displayed concurrently on a graph or report.
7) The trend graph display shall automatically scale the value and time axis to display all samples.
From the trend graph, the operator shall be able to select and read the instantaneous value of any
previous sample.
8) The trend point graphing capability shall be a built-in feature of the system and shall not require
operator set- up. Systems which require trend point data to be exported to third party software shall
not be acceptable.
4.15 Totalization
1) For every digital point, the system shall be able to calculate:
Cumulative on-time
Cumulative off-time
2) For every point, analog and digital, the system shall be able to calculate:
Cumulative time in alarm
Cumulative time overridden by operator
Cumulative time off-line
3) Time totalization shall have a resolution of one minute or less.
4) Time totalization shall be displayed in hours.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 325
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The system shall calculate a predicted demand based on the sliding window average of the previous 20
minutes of consumption. The predicted demand shall be used for control calculations.
The operator shall be able to lock a load so that it is ineligible for shedding by demand, limiting or load
rolling.
The operator shall be able to use the scheduling feature to program time/days for a load to be locked and
unlocked.
The operator shall be able to use the scheduling feature to program time/days for target values for the demand
limiting and load rolling features.
The demand limiting/ load rolling features shall allow a minimum of four priority groups to be defined.
The operator shall be able to define a target reduction of electrical consumption and the load rolling feature
shall turn off equipment to meet this target.
The operator shall be able to define a demand target that is not to be exceeded and the demand limiting
feature shall analyze trends and electrical demand and turn off equipment when a demand peak is anticipated.
The demand limiting and load rolling features shall be fully integrated with all other features so that the
following safety parameters are maintained:
Minimum on time
Minimum off time
Maximum off time
Maximum number of cycles per hour
At the end of the minimum off time, a comfort parameter, such as a temperature, shall be sampled. If the
comfort parameter is in alarm, the point being controlled shall be turned on.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 326
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The operator shall be able to define the tracking period for the statistical date as:
Hourly (automatic reset)
Daily (automatic reset)
Weekly (automatic reset)
Monthly (automatic reset)
Manual reset
To provide the operator with an opportunity to manually shed loads that are not available to demand limiting
or load rolling, the operator shall be notified when the demand limiting or load rolling run out of loads to shed.
To advise the operator when the performance is outside of expectations, the operator shall be notified when
the demand peak target or load rolling target is exceeded.
The contractor at the time of submission of tender shall list out the modification capabilities of the system.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 327
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Maintenance schedules
Maintenance history
Maintenance instructions
Resource management
Weekly work orders
Reactive maintenance
Progress monitoring
Energy software module shall monitor energy consumption through a variety of customizable reports.
Energy software shall act as an especially powerful tool when integrated with the building automation
solution, so that it can automatically download real-time information on energy use and environmental
settings. It shall easily view monthly consumption, detect deviations, compare and benchmark with similar
Hotels or past consumption all based on the latest current data. Energy software shall track direct energy
consumption of all kinds, giving powerful tool for identifying potential savings.
Energy efficiency Monitoring of MEP equipments such as chillers, pumps, CT, DG Sets, Boilers
etc..
Environmental impact of energy use
Reading interval adjustment
Degree days
Main and sub meters
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 328
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Meter changes
Versatie reporting
Meter reading schedules
Freely definable monitoring objects
Direct link to building automation system
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 329
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contract software shall control and manage all aspects of Hotels maintenance contracts, including cost,
check dates, contract parties and many other details. It shall group and sort contracts freely, based on
operators account scheme or any desired system. Contracts shall also be linked to objects such as buildings
or systems, helping you track contractor performance and building costs. It shall keep every detail under
control, while producing a variety of reports that shall make strategic decisions.
Flexible structure of contracts
Check dates and other detail controls
Search and reporting
Contract parties and contract costs
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 330
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5) Controllers requiring nickel-cadmium/lithium battery to support the full operation of the RAM, shall
have battery back-up upto 12 hours in the event of a localized mains failure. The battery shall not be
required to supply power to actuators, valves, dampers etc.
In addition to the above battery reserve a further battery shall be provided to retain the RAM for a
minimum of 2 days, after the expiration of the standard battery.
A low battery alarm shall be provided with each Controller and with an indication at the Control
Station.
In case the memory is stored on EEPROM, the battery backup will not be required.
6) The Controllers shall have proportional control, Proportional plus Integral (PI) Control, Proportional
plus Integral Plus Derivative (PID) Control, Two Position Control and Time Proportioning Control
and algorithms etc, all in its memory and all available for use by the user, i.e. all the control modes
shall be software selectable at any time and in any combination. The analog output of Proportional
Control, PI Control, and PID Control shall continuously be updated and output by the program shall
be provided. Between cycles the analog output shall retain its last value. Enhanced integral action in
lieu of Derivative function shall not be acceptable.
7) The controllers shall have a resident real time for providing time of day, day of week, date, month
and year. These shall be capable of being synchronized with other clocks in the network.
Back-up power shall support the clock. Upon power restoration all clocks shal be automatically
synchronized.
8) The microprocessor based DDCs shall be provided with power supply, A/D and D/A converters,
memory, and capacity to accommodate a maximum of 48 input/output (I/O) hardware points (with
or without an expansion board). DDCs with a lower capacity of points shall preferably be
provided at the locations with relatively less input/output points for AHU, FAN & other utilities
(accommodated maximum 2nos. of AHU or FAN). The controller have peer to peer
communication and max 100 controller shall be connected per network loop
9) If the controllers provided by the contractor have the configurable plug in function cards, then the
following minimum specifications shall have to be met :
i) In addition to the basic outstation, a minimum of two slots shall be provided for the insertion of
plug-in function cards.
ii) The cards shall provide for analog or digital, input or output, hardwired connections to the
installed plant.
iii) The quantity and combination of these cards shall be determined by the requirements of the plant
in that location with the concurrence of the Owner/ Consultant.
10) The DDCs shall have 15% spare capacity (digital/analog input/output) to give flexibility for
future expansion.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 331
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
11) All DDC controllers shall be capable of handling voltage, mili-ampere, resistance or open and closed
contacts inputs in any mix, if required.
Analog inputs/outputs of the following minimum types shall be supported :
i) 4-20 mA.
ii) 0-1 volts.
iii) 0-10 volts.
iv) 0-5 volts, and
v) 2-10 volts.
vi) Resistance Signals (either PTC or NTC 1.8 KNTC)
(PT 100, PT 1000, PT 3000, Balco 500, NI 1000)
Digital input/output types to be supported shall be, but not limited to the following :
i) Normally-open contacts.
ii) Normally-closed contacts.
Modulating outputs shall be true proportional outputs and not floating control type.
12) Controllers packaging shall be such that, complete installation and check out of field wiring can
be done prior to the installation of electronic boards.
13) All board terminations shall be made via plug-in connectors to facilitate trouble-shooting, repair
and replacement. Soldering of connections shall not be permitted.
14) Controllers shall preferably be equipped with diagnostic LED indicators with atleast indication for
Power up Test OK, and Bus Error. All LEDs shall be visible without opening the panel door.
15) It shall be possible for the controllers to accept regulated uninterrupted power supply to maintain full
operation of the controller functions (control, logging, monitoring and communications) in the event
of a localized mains failure.
16) Controllers requiring fan cooling are not acceptable.
17) There shall be the facility for accessing controller data information locally , via a portable plug-in
keypad display which can be common to all controllers and normally removed to prevent
unauthorized tampering. Alternatively each controller shall have a keypad and display integral
with its casing for local interrogation and adjustment. In either case, access to the system thus
provided shall be restricted by passwords in the same way as at the main operator terminal.
18) In case the Portable operator Terminals (POT) are required to program the controllers, sockets
shall be provided for same. Attachment of POT shall not interrupt or disable normal panel
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 332
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 333
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
f) Load reset
g) Zero energy band
h) Duty cycle
i) Enthalpy analysis and control
j) Run Time Totalization
k) Sequencing and Optimization
l) Exception scheduling
Detailed description of software features and operating sequence of all available energy management
software shall be submitted with the tender for evaluation by the
Consultant.
7) The DDC Controllers shall have Adaptive Control capability whereby the control software
measures response time and adjusts control parameters accordingly to provide optimum control.
The software shall allow self-tuning of the variable control loops (all or any of P, P+I, P+I+D) of
the AHUs and chiller system so as to provide the most efficient and optimized controls at
different load conditions. The energy management programs shall update their parameters based
on past experience and current operating conditions.
8) Alarm Lockout shall be provided to prevent nuisance alarms. On the initial start up of air handler
and other mechanical equipment a timed lockout period shall be assigned to analog points to
allow them to reach a stable condition before activating an alarm comparison logic.
Tenders shall indicate their proposed system alarm handling capability & features.
9) Run time shall be accumulated based on the status of a digital input point. It shall be possible to
total either ON time or OFF time. Run time counts shall be resident in non-volatile memory.
10) It shall be possible to accommodate Holiday and other planned exceptions to the normal time
programs. Exception schedules shall be operator programmable up to one year in advance.
11) Distributed power demand program shall be based on a sliding window instantaneous demand
trend algorithm. The DDC interfaced to the demand meter shall calculate the demand, forecast the
demand trend, compare it to the established demand limits, and initiate load shedding or re-
establishment of loads as required. Shedding shall be on a sequential basis with least important
loads shed first and restored last.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 334
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
high level integration and networking capabilities including and not limiting to Operator Work Station,
Remote Work Station, Third Party Management System etc. The same facility shall be available at
controller level in two tier system architecture. Network bridges & routers must be of a modular design to
ensure reliability & system performance. The central system shall use the building Local Area Network
(LAN) for communication. The communication between the central server and the controllers shall be
BACnet/IP. Proprietary protocols are NOT acceptable.
1) Where information is required to be transmitted between controllers for the sharing of data such as
outside air temperature, it shall be possible for global points to be allocated in the SIU such that
information may be transmitted either on change of incremental value or at specific time intervals.
2) SIU must be able to perform the following energy management functions as a minimum.
a. Time & Event Program
b. Holiday Scheduling
c. Maximum and Distributed power demand
d. Optimum start and stop program
e. Night Purge
f. Load reset
g. Zero Energy band.
h. Duty Cycle.
i. Enthalpy analysis and control.
j. Run Time Totalization.
k. Sequencing and Optimization.
l. Exception scheduling
Detailed description of software features and operating sequence of all available energy
management software shall be submitted with the tender for evaluation by the Consultant.
3) Alarm Lockout shall be provided to prevent nuisance alarms. On the initial start up of air handler
and other mechanical equipment a timed lockout period shall be assigned to analog points to
allow them to reach a stable condition before activating alarm comparison logic.
4) It shall be possible to accommodate holiday and other planned exceptions to the normal time
programs. Exception schedules shall be operator programmable upto one yea in advance.
5) Distributed power demand program shall be based on sliding window instantaneous demand trend
algorithm. The DDC interfaced to the demand meter shall calculate the demand, forecast the
demand trend, compare it to the established demand limits, and initiate load shedding or re-
establishment of loads as required. Shedding shall be on a sequential basis with least important
loads shed first and restored last.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 335
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3) The POT shall be complete with command keys, data entry keys, cursor control keys and a 24
character liquid crystal alphanumeric display. Access shall be via self prompting menu selection
with arrow key control of next menu/previous menu and step forward/backward within a given
menu.
4) Connection of a POT to a controller shall not interrupt or interfere with normal network operation
in any way, prevent alarms from being transmitted, or interfere with Control Station commands
and system modifications.
5) Connection of POT at any controller shall provide display access to all controllers on that bus. In
case the controller has a fixed LCD display and entry keyboard, then the display access shall be
available on each screen.
6) It should be possible to override the commands given through POT by the Operator Control
Station.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 336
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Each controller shall have equal rights for data transfer and shall report in its predetermined time slot. There
shall be no separate device designated as the communications master. Those systems using dependent
controllers shall be pointed out by the contractor and a dual redundant transmission media with automatic
switching and reporting in the event of line faults will have to be provided.
Single or multiple stand alone controller failures shall not cause loss of communication between active
control panels connected on the communication network. Full communication shall be sustained as long as
there are atleast two operational stand alone control panels active on the communication network.
All the System Integration Units shall be linked together on a Local Area Network.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 337
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The communication network shall include provision for automatically reconfiguring itself to allow all
operational equipment to perform as efficiently as possible in the event of single or multiple failure.
The communication network shall follow the recommendations of ISO 7498 or equivalent standard. The
BAS supplier shall be required to provide details of standards to which their system conforms.
General Requirements
All controls shall be capable of operating in ambient conditions varying between 0-55 deg. C and 90% R.H.
non-condensing.
All Control devices shall have a 20 mm conduit knockout. Alternatively, they shall be supplied with adaptors
for 20 mm conduit.
Ancillary Items
When items of equipment are installed in the situations listed below, the BAS contractor shall include the
following ancillary items :
All devices required to be weatherproofed are detailed in the Schedule of Quantities. IP ratings for the
equipment is mentioned in the respective section.
Corrosion resisting pockets of a length suitable for the complete active length of the device, screwed
(13 mm) or (20 mm) NPT suitable for the temperature, pressure and medium.
Mounting flanges, clamping bushes, couplings, locknuts, gaskets, brackets, sealing glands and any special
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 338
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Additional features
(i) Concealed Adjustment : All two position switching devices shall have concealed adjustment unless
detailed otherwise in the Schedule of Quantities.
(ii) Operating Voltage : All two position switching devices shall operate on 230 v a.c and all accessible live
parts shall be shrouded. An earth terminal shall be provided.
Temperature sensors for space, pipes and ducts, shall be of the Resistance Temperature detector (RTD) type
or thermistor. These shall be two wire type and shall conform to the following specifications :
1) Immersion sensors shall be high accuracy type with a high resistance versus temperature change.
The accuracy shall be atleast 0.33 degrees F and sensitivity of atleast 2 ohm/F.
2) Immersion sensors shall be provided with separate stainless steel thermo well. These shall be
manufactured from bar stock with hydrostatic pressure rating of atleast 10 kgf/cm2.
3) The connection to the pipe shall be screwed inch NPT (M). An aluminum sleeve shall be
provided to ensure proper heat transfer from the well to the sensor. Terminations to be provided on
the head. Flying leads shall not be acceptable.
4) The sensor housing shall plug into the base so that the same can be easily removed without
disturbing the wiring connections.
5) Duct temperature sensors shall be with rigid stem and of averaging type. These shall be suitable
for duct installation.
6) Outdoor air temperature sensor shall be provided with a sun shield.
7) The sensors shall not be mounted near any heat source such as windows, electrical appliances etc.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 339
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Space and duct humidity sensors shall be of capacitance type with an effective sensing range of 10% to 90%
RH. Accuracy shall be + 3% or better. Duct mounted humidity sensors shall be provided with a sampling
chamber. Wall mounted sensors shall be provided with a housing. The sensor housing shall plug into the base
so that the same can be easily removed without disturbing the wiring connections. The sensors shall not be
mounted near any heat source such as windows, electrical appliances etc.
The exact ranges to be set shall be determined by the contractor at the time of commissioning. It should be
possible to zero the flow meter without any external instruments, with the overall accuracy of atleast 1%
full scale.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 340
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The switch shall be of differential pressure type complete with connecting tube and metal bends for
connections to the duct. The housing shall be IP 54 rated. The pressure switches shall be available in
minimum of 3 ranges suitable for applications like Air flow proving, dirty filter, etc. The set point shall be
concealed type. The contact shall be SPDT type with 230 VAC, 1 A rating.
The switch shall be supplied suitable for wall mounting on ducts in any plane. It should be mounted in such a
way that the condensation flow out of the sensing tips. Proper adaptor shall be provided for the cables.
The set point shall fall within 40%-70% of the scale range and l have differentials adjustable over 10%-30%
of the scale range.
The switches shall be provided with site adjustable scale and with 2 NO/NC contacts.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 341
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Power factor, Voltage, Current, Frequency and Kilowatt transducers shall have standard output signal for
measurement for the specified variable.
Kilowatt-Hour metering (if any) shall be poly-phase, three- element with current transformer (CT) operated
type. The metering shall feature high accuracy with no more than +/- 1% error over the expected load range.
The coils shall be totally encapsulated against high impulse levels.
Valves
a. Type : Two or Three way mixing
b. Stem / Trim : SS-316 or better
c. Plug and seat : SS-316 or better
d. Plug characteristics : Equal Percentage
e. Service : Chilled water
f. Packing : Teflon
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 342
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Actuator
a. Actuator : Electrical/Electronic/Magnetic.
b. Actuator type : Proportionating(Modulating)
c. Spring return function : No
d. Travel limit switch : 2 Nos. for open and close.
e. Hand wheel : Required
f. Input signal : 0 10 V dc, 4 20 mA
g. Power Supply : 240 V ac
h. Thrust : To be selected by the vendor
i. End Connections : Screwed upto 2 Beyond that ANSI 150
Lb RF
j. Noise Level : Not exceeding 70 DB
k. Weather Proof : NEMAI
Note :
i. Actuator should be directly coupled to the trim. Eccentric linkages not acceptable.
ii. Leakage not to exceed 0.1% of flow.
Control valves for the Air Handling Units shall be globe type, two way suitable for Variable flow hydronic
system as indicated in BOQ.
Two way motorized valves shall be provided in chilled water lines at each fan coil units. The valve shall be
actuated by space thermostat. Constant space conditions shall be maintained by allowing chilled water
through the coil. The valve shall be provided with spring return function so that it revert to fully closed
position when fan is shut off. Valve shall be two/three position with flare connections. Valve shall have the
facility to replace motor \ actuator without removing the valve body Actuator shall be suitable for 240 V,
50 Hz ac or 24V ac. Maximum close off pressure shall be selected to suite the CV requirement.
9.14.2 Thermostat
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 343
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Thermostat shall be snap acting fixed differential type thermostat for air-conditioning application for
actuating the two way valve at each fan coil unit with HI-MED-LO fan switch and system setting OFF-
FAN-COOL. Switching off must break fan circuit. Thermostat shall be provided with necessary relays to
operate valve of cooling coil.
9.15.2 Actuators
Type : Electric .
Duty. : On/Off (Maximum 50 operations per day)
Motor power supply : 230 V AC or 415 V 3-phase
Travel limit switches : 2 Nos
Torque limit switches. : 2 Nos
Hand wheel : Required
NOTE
a. Actuator must open/ close with one changeover contact. Control panel, if required, must be
supplied integral with the Actuator.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 344
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
b. No gear box is envisaged, however if gear box is provided, the travel limit switches must
be connected directly to the valve stem.
c. Cover tube for the valve stem must be provided
The specifications for the electronic meters to be supplied by BAS contractor is as follows:
Instantaneous Measurements :
a. V (1-n), V (1-1) & 1 per ph & avg. V & I unbalance
b. PF per ph & total, frequency
c. Power & BI-directional energy (active, apparent, reactive)
d. Peak & Predictive Demand (I, W, VA, VAR totals)
e. V & I harmonics (Individual & Total)
f. Time of use (internal calendar, multiple daily tariff, energy & demand accumulators).
Software interface shall be ensured by BAS contractor for the electronic meters. Systems requiring
transducers for duplicating the data shall not be accepted.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 345
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All the instantaneous measurements shall be displayed on the control stations and the data shall be logged. It
shall be possible to access minimum / maximum logging of any parameter with alarm annunciation for
unusual measurements. The system shall also accept user defined Set-Point limit of any parameter.
The panel shall be metal enclosed 14 SWG CRCA sheet steel cubicle with gaskets between all adjacent units
and beneath all covers to render the joints dust proof. All doors and covers shall be hinged and latched and
shall be folded and braced as necessary to provide a rigid support. Joints of any kind in sheet metal shall be
seam welded with welding slag grounded off and welding pits wiped smooth with plumber metal.
All panels and covers shall be properly fitted and secured with the frame and holes in the panels correctly
positioned. Fixing screws shall enter into holes tapped into an adequate thickness of metal or provided with
nuts. Self threading screws shall not be used in the construction of control panels. Knockout holes of
approved size and number shall be provided in the panels in conformity with the location of incoming and
outgoing conduits/cables. lamps shall be provided to support the weight of the cables. The dimension of the
boxes shall depend on the requirement with the color decided in consultation with the Architect/Consultant.
Note : All panel enclosures used in plant room spaces and external to building shall be suitable for outdoor
application (IP 54 protection) and UL listed.
11.1 CONDUITS/TRUNKER
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 346
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Conduits and accessories shall conform to relevant Indian Standards. PVC conduits of required dia shall be
used as called for in the schedule of quantities. Joints between conduits and accessories shall be securely
made, with help of adhesive.
The conduits shall be delivered to the site of construction in original bundles and each length of conduit
shall bear the label of the manufacturer.
11.2 CONNECTIONS
All jointing methods shall be subject to the approval of the Architect/Engineer. Separate conduits shall run
for all power wiring.
The threads and sockets shall be free from grease and oil. Connections between conduit and controller
metal boxes shall be by means of brass hexagon smooth bore bush, fixed inside the box and connected
through a coupler to the conduit. The joints in conduits shall be smooth to avoid damage to insulation of
conductors while pulling them through the conduits.
The saddles shall be 2 mm x 19 mm galvanized steel flat, properly treated, primer coated & painted,
securely fixed to supports by means of nuts and bolts/rawl bolts and brass machines screws.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 347
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
No joint shall be shaved off like length of the conductors. Insulation shall be shaved off like sharpening of
a pencil and it shall not be removed by cutting it square to avoid depression/cutting of conducting material.
Strands of wires shall not be cut to accommodate & connect to the terminals. Terminals shall have
sufficient cross-sectional area to take all the strands.
No wire shall be drawn into any conduit until all work of any nature that may cause injury to wire is
completed. Before the wires are drawn into the conduit, the conduits shall be thoroughly cleaned of
moisture, dust, dirt or any other obstruction. Where wires are connected to detectors, or panel, sufficient
extra length of wires shall be provided to facilitate easy connections and maintenance. If numbers of cables
are > 4 than cable tray of appropriate size to be used.
Only licensed supervisors/wiremen shall be employed for cabling and other connected work. Only
approved make of cables shall be used. The cables shall be brought to the site in original packing.
The cabling running between the system integration units to the DDC controllers shall be defined as
communication cable. This cable along with conduits shall also be measured on per I/O point basis.
LAN Cable
The cable connecting various system integration units to the control station shall be termed as LAN cable.
This cable alongwith conduits shall be measurable on unit length basis.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 348
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 349
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 350
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 351
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 352
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 353
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 354
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 355
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 356
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The design shall comply with rules of the local fire service department / authorities. The Fire Protection
System design shall be based on the following codes & Standards :
Table 6: Codes for Fire Fighting Requirements
IS 1239 (Part-I): 1990 Mild Steel Tubes, Tubulars and Other Wrought Steel Fittings: Part-I
Mild Steel Tubes (Fifth Revision)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 357
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS 1239: (Part-II): 1992 Mild Steel Tubes, Tubulars and Other Wrought Steel Fittings: Part-II
Mild Steel Tubulars and Other Wrought Steel Pipe Fittings (Fourth
Revision)
IS 3589: 2001 Steel Pipes for Water and Sewage (168.3 to 2540 mm
Outside Diameter) Specification (Third Revision)
IS 12835: Part I: 1989 Code of practice for design and installation of fixed fire extinguishing
system Part 1 Low expansion foam
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 358
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS 2097: 1983 Specification for foam making branch pipe (first revision)
NFPA-20 Standard for the Installation of Stationary Pumps for Fire Protection
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 359
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.0 MATERIALS:
The pipes shall be galvanized mild steel `C' class Factory welded pipes and seamless screwed
and socket tubes shall be conforming to the requirement of IS 1239-1964 for Heavy grade. They
shall be of the Dai. (nominal bore) specified in the description of the item. The representative
nominal bores of the pipes for which they are intended shall designate the socket.
The pipes and sockets shall be clearly finished, well Galvanized in and out and free from cracks,
surface flows, laminations and other defects. All screw threads shall be clean and well cut. The
ends shall be cut cleanly and square with axis of the tube.
All screw tubes & sockets shall have pipe threads conforming to the requirement of IS 544-1955
(or revised) screwed tubes shall have threads while the sockets shall have parallel threads.
The fitting shall be of malleable cast iron or MS. tubes complying with all the appropriate
requirements given as specified. The respective nominal bore of the pipes for which they are
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 360
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The fittings shall have screw threads at the ends conforming to the requirements of IS 544-1955
(or revised). Female threads on fitting shall be parallel & male threads (except on
running nipples & collars of unions) shall be taper.
The pipes shall be cleaned & cleared of all foreign matter before being laid. In jointing the
pipes, the inside of the socket & the screwed end of the pipes shall be oiled & rubbed over with
white lead & a few turns of spun yarn wrapped round the screwed end of the pipe. The end shall
then be screwed in the socket, Care should be taken that all pipes & fitting are properly jointed
so as to make the joints completely water tight & pipes are kept at all time free form dust & dirt
during the fixing. Burr from the joint shall be removed after laying; the open ends of the pipes
shall be temporarily plugged to prevent access of water, solid or any other foreign matter.
All pipes & fittings shall be fixed truly vertical & horizontal unless unavoidable. The pipes shall
be fixed to walls with standard pattern holder bat clamps of required shapes & size so as to fit
tightly on the pipes when tightened with screwed bolts.
These clamps shall be embedded in brickwork in cement mortar 1:3 (1 cement3 coarse sand) &
shall be spaced at regular intervals in straight lengths as shown in the table given below.
1.1.3 Concrete walls / floors at no time shall be chiseled out for fixing the pipes. The contractor shall
use masonry drill to drill the hole and use anchor bolts to fix the pipe.
LENGTHS
SIZE OF PIPE HORIZONTAL RUNS VERTICAL RUNS meters
mm. Meters
15 2 2.5
20 2.5 3
25 2.5 3
32 2.5 3
40 3 3.5
50 3 3.5
65 3.5 5
75 3.5 5
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 361
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The clamps shall be fixed at shorter lengths near the fittings as directed by the Engineer-in-
charge.
For GI pipes 15mm to 25 mm Dai. the holes in the walls & floors shall be made by drilling
with drill bits & not by dismantling the brick work or concrete. However, for bigger diameter
pipes the holes shall be carefully made of the smallest size as directed by the Engineer-in-
charge. After fixing the pipes the holes shall be made good with cement mortar 1:3 (1 cement:
3 coarse sand) & properly finished to match the adjacent surface.
3.0 EXTERNAL WORK:
The galvanized iron pipes & fittings shall be laid in trenches. The widths & depths of the
trenches for different diameters of the pipes shall be as in the table given below :
DIA. OF PIPE WIDTH OF TRENCH DEPTH OF TRENCH
15 mm TO 50 mm 300 mm 60 cm
65 mm TO 100 mm 450 mm 75 cm
At joints the trench width shall be widened wherever necessary. The work of excavation &
refilling shall be done true to line & gradient.
The pipes shall be painted with two coats of Anti-corrosive bitumastic paint of approved
quality. The pipe shall be laid on a layer of 7.5cm sand & filled with sand upto 15 cm above the
pipes. The remaining portion of the trench shall then be filled with excavated earth. The surplus
earth shall be disposed off as directed.
In case of bigger diameter (65mm & above) pipes where the pressure is very high, thrust blocks
of cement concrete 1:2:4: (1 cement: 2 coarse sand: 4 grade stone aggregate of 20 mm nominal
size) shall be constructed on all bends to transmit the hydraulic thrust without impairing the
ground & spreading it over a sufficient area.
After jointing, the pipes & the fittings shall be inspected under working conditions of pressure
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 362
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
& flow. Any joint found leaking shall be redone & all leaking pipe removed & replaced
without extra cost.
The pipe & fittings after they are laid shall be tested to hydraulic pressure of 15 Kg/cm2 (150
meter) The pipes shall be slowly & carefully charged with water allowing all air to escape &
avoiding all shocks of water hammer. The draw of taps & stopcocks shall then be closed &
specified hydraulic pressure shall be applicable gradually. Pressure gauge must be accurate &
preferably should have been re-calibrate before the test. The test pump having been stopped the
test pressure should be maintained without loss for at least half an hour. The pipes & fitting
shall be tested in sections as the work of laying proceeds, keeping the joints exposed for
inspection during the testing.
he pipes shall be of the class specified in the Schedule of Quantities & shall be of galvanized
steel, welded or seamless, screwed & socketed shall conform to IS: 1239. A firm of repute shall
manufacture them. All fittings shall be malleable iron galvanized fittings of approved best
Indian make. The detail of the pipes regarding nominal bore thickness & weight are given
below:
SCREWED
&
SCREWED & SOCKETED
APP. NOMINALBORE SOCKETED
METERS / 1000 KG.
OUT Wt/Mtr
SIDE DIA. MM NEAREST LIGHT MEDIU HEAVY HEAV MEDI LIGH
inch Kg. M Kg. Kg. Y Kg. UM T Kg.
Kg.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 363
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
NOTE: The above weights are for black pipes & theoretical weights of galvanized pipes are 6% higher.
This Shall conform to the IS 1536 - 11967 (Class LA) as specified in the schedule. They shall
be laid, jointed & tested along with the C.I pipes as described in the specification for C.I.S/S
pipes.
8.0 FITTINGS:
General The brass or gunmetal fittings shall be heavy quality & approved manufacturer &
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 364
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
pattern with screwed or flanged ends as specified. The fittings shall in all respects comply with
the Indian standard Specifications NO.IS: 778-1957 & IS.781- 1959. The nominal bore of the
pipe outlet to which the fittings are attached shall designate the standard size of brass gunmetal
fittings. A sample of each kind of fittings shall be got approved from the Engineer-in-charge &
all supplies made according to the approved samples.
All cast fittings shall be sound & free from laps, blowholes & fittings; both internal & external
surfaces shall be clean, smooth & free from sand etc. Burning plugging, stopping or patching of
the casting shall not be permissible. The bonnets, spindles & other parts shall be truly machined
so that when assembles the parts shall be axial, parallel & cylindrical with surface smoothly
finished.
The area of the waterway of the fittings shall not be less than the area of nominal bore. The
fittings shall be fully examined & cleared of all foreign matter before being fixed. The fittings
shall be fixed in the line in a workman like manner. The joints between fittings & pipes shall be
made leak proof. The joints & fittings shall be leak proof when tested to a pressure of 15KG/
CM2 as described in para 1.1.5 - the defective fittings & joints shall be replaced or redone.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 365
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
9.1 GUN METAL FULLWAY VALVE WITH WHEEL: These shall be of the Gun metal fitted
with wheel & shall be of Gate valve type opening full way & of the size as specified. These
shall generally conform to IS.778-1957 & their approximate weights shall be given in para 1.2.
9.2 Ball valve: The ball valve shall be of high pressure class & shall be of sizes as specified.
The nominal size of a ball valve shall be that corresponding to the size of the pipe to which it is
fixed. The ball shall be of brass or Gun metal as specified, & the float of copper sheet. The
minimum gauge of copper sheet used for making the float shall be 45 for float upto 115 mm
Dai. & 55 for float exceeding 115mm Dai. This shall be spherical in shape. The jointing of the
float shall be made by efficiently burnished, lapped & soldered seam or by brazing. Plastic float
may also be used if specified. The body of ball valve when assembled in working conditions
with the float immersed to not more than half of it's volume shall remain closed against a test
pressure of 10.5Kg/sq. Cm. & low pressure shall against a test pressure of 3.5Kg/sq. cm.
The ball valve shall generally conform to IS specifications No. 1703-1962. The weight of
ball cock & the size of ball shall be as per table given below.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 366
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
valve unless otherwise specified. The hydrant shall confirm to IS.909-1958 & shall consist of
the following components:
One sluice valve class 1 type confirms to IS.780-1963.
One duck foot bends.
One 65mm male coupling instantaneous pattern and.
One Cast iron cap permanently secured to the duck foot bend by means of a chain. Where the
fire services requirement of coupling differs from the above, the requisite coupling shall be
provided at no extra cost.
The body & cover shall be of good quality cast iron spindle & bronze & the nut & the
valve seat of leaded in tin bronze. The bodies, spindles & other parts shall be truly machined
with surface smoothly finished.
The hydrant shall be fully examined and cleared of all foreign matter before being fixed. The
fixing shall be done on the water main, which shall be of minimum 75mm dia. The flanged
end of the hydrants shall be fixed to the flanged outlet of a tee in the water main by means of
bolts, nuts & 3mm rubber insertion or chemically treated compressed fiber bore 1.5 mm
minimum thickness & of weight not less than 0.183 gm. per sq.cm. This can also be fixed by
means of flanged tailpiece, which may be connected to the water main by C.I. specials.
10.2 Appurtenances:- The other appurtenances of pipe line are mentioned below:-
Air Vents: These are placed at every summit in the pipeline to permit the escape of air when
the main is filled, & afterwards if any air is carried into the mains. These are also placed on
long stretches of nearly level main.
Scour Valves: These are placed at bottom of the all depressions of pipes for emptying the main
or letting out the sediment.
Reflux Valves: These are fixed so as to open in the direction of flow but automatically to close
if the water flows back. They are used to diminish the damage done by the escape of water due
to a burst or to prevent damage to impellers of Pump.
Safety or Relief Valves: These are fixed at the down stream ends of long lengths of main or
where water hammer may take so as to reduce from any excessive pressure to the nominal if it
occurs.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 367
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
10.3.3 Bed concrete: This shall be of cement concrete 1:3:6 (1 cement:3 fine sand:6 graded stone
aggregate 40mm nominal size).
10.3.4 Brick work: This shall be in 2nd class bricks in cement mortar 1:5(1 cement : 5 fine sand)
10.3.5 Plastering: Plastering not less than 12mm thick shall be done in cement mortar 1:3 (1 cement: 3
coarse sand) finished with a floating coat of neat cement.
10.3.6 Surface Box: This shall be of cast iron, well made & free from casting & other defects. All
sharp edges shall be removed & finished smooth. The clear of dimensions for surface boxes for
stop cocks sluice valves, fire hydrants, water meters, etc. shall be given in drawing.
C.I. surface boxes shall be coated with black bituminous composition except in the case of fire
hydrants where the cover of the surface box shall be painted with two coats of rust resisting
bright luminous yellow paint for clear visibility during night.
The C.I. surface box shall be fixed on the top of the masonry chamber and provided with plain
or reinforced cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm
nominal size.)
11.0 HANGERS & SUPPORTS :
GENERAL: Provide proper solid angle iron channel section, supports for all pipes complete
with clamps. Wherever insulation cores, to provide wooden guide to support pipe on the angle
iron hangers/supports. For attachment in concrete, use "Dash" fasteners or anchor plug type
inserts or equivalents. Provide hangers within 0.9 meter of all hangers in direction of mains & a
minimum of three hangers per expansion bend wherever shown in drawing. Provide all
additional structural steel angles, channels or other members not specifically shown but are
required for proper support. At no time concrete reinforcement should be allowed to drill
exposed & hangers hang on them.
Where necessary additional hangers to be provided to arrest water hammers or hydraulic
resonance with proper rubber padding.
Space hangers, as noted below, except on all soil pipe which shall have a hanger or multiple
fittings, sufficient hangers shall be provided to maintain proper slope without sagging, in case
of angle suspended line, the following is suggested.
A. Pipe Sizes Hanger Rod Dia.
20 mm through 50 mm 9 mm.
65 mm through 125 mm 12 mm.
150 mm and over 16 mm.
B. Pipe Sizes Spacing of Supports
12 mm to 20 mm 1.5 M apart
25 mm to 40 mm 1.8 M apart
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 368
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Bronze/SS
65 mm &
Gas Gate 600 psi flanged spindle &
under
trim
Water, Oil, air, Gas, 65 mm &
Globe & angle 300 psi. Screwed Bronze
steam (low pressure) under
65 mm &
Water Globe & Angle 300 psi. water Screwed Bronze
under
Water Globe & Angle 65 mm & 300 psi. Flanged Iron body
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 369
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
over bronze
trim
Horizontal & 65 mm &
Water 300 psi. Screwed Bronze
vertical check under
Iron body
Horizontal & 65 mm &
Water 300 psi. Flanged bronze
vertical check over
trim
12.4 All globe & check valve shall have working parts suitable for hot & cold water, oil or gas as
required. Valves shall be tagged with permanent label under band wheel indicating type of
duty.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 370
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
13.4 JOINTING:
13.4.1 Joints for black steel pipes 50 mm Dai & below fitting shall be metal tapered threaded joints
using red lead for rust prevention. Joints shall be welded for sizes 65mm Dai above as
approved by the Engineerin-charge. (Welding shall conform to relevant I.S.)
13.4.2 Joints between GI or black steel pipes & valves & other appurtenances shall be made with G.I
or black steel flanges. Flanges joints shall be made with 3mm thick insertion rubber washer.
Flanges shall be of Table "E" and shall conform to IS 1538 Part IV to Part VI which shall be
cut and drilled out of MS Plates. MS cut flanges shall be galvanized before welding to G.I
Pipes.
13.5 SLUICE VALVES & NON RETURN VALVES:
Sluice valves (80mm & above dia) shall be cast iron double flanged with non-rising spindle.
Sluice valves below ground shall be provided with caps suitable for operations by a key. Sluice
valves in exposed locations shall be provided with cast iron wheel. Sluice valves shall conform
to IS 780(class I 1969) & tested to 20 kg/sq. cm pressure.
13.6 FIRE HYDRANTS:
13.6.1 The contractor shall provide on each landing & externally as shown on drawing one (twin
headed gun metal landing valve with 63mm dia outlet to & 100mm inlet) IS 5290 -1969 with
cast iron wheels. Landing valve shall have flanged inlet & suitable for fire brigade hoses 63mm
Dai.
13.7 FIRE HOSE REELS:
13.7.1 The contractor shall provide standard fire hose reels with 20mm Dai high pressure Dunlop
rubber hose 30 M long with gunmetal nozzles & control valve, shut off valves, all mounted on
circular hose reel of heavy mild steel construction & cast iron bracket. Hose reel to be firex,
minimax or equivalent. Hose reel shall conform to I.S. 884 - 1969.
13.8 DRAIN VALVES:
13.8.1 Provide 50mm Dai black steel pipe to I.S. 1239 heavy class with 50mm gunmetal fullway valve
for draining any water in the system in low pockets.
13.9 PIPE PROTECTION:
13.9.1 Paint all pipes above ground & in exposed location with one coat of red oxide primer & two or
more coats of post office red paint of approved shade as approved by the Engineer - in - charge.
(Buried pipe shall be covered by hessian cloth dipped in coal tar, after a coat of bitumen on
pipe).
13.10 PIPE SUPPORTS:
13.10.1 Support all pipes adequately from slabs or walls by a structural support fabricated from MS
structural roads, channels, angles & flats. All clamps shall be painted with one coat of red oxide
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 371
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
& two coats of post office red channel paint. (Buried pipes shall have 150mm deep PCC bed
haunched to half the Dia. of pipe).
13.11 TESTING:
13.11.1 Test all piping in the system to a hydrostatic pressure of 16 KG. /sq.cm without drop in
pressure for ablest 2 hours.
13.11. Rectify all leakages, make adjustment & re-test as required & directed by the Engineer - in
- charge.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 372
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
14.3.1 The fire pump shall be single or double suction centrifugal type with split casing and direct
driven by electric motor or diesel engine as specified. The pump rating and performance shall
conform to the Equipment Schedule and meet the TAC duty requirements.
14.3.2 Pump casing shall be of close grained cast iron with bronze impeller. The shaft sleeve shall be
brass or SS 304 and the trim shall be brass or bronze.
14.3.3 Pump shall be capable of delivering 150% of the rated capacity at 65% of the rated head and
the No-delivery head shall be more than 140% of the rated delivery head. The pump casing
shall withstand 1.5 times the no-delivery pressure or 2 times of the duty pressure whichever is
higher.
14.3.4 The pump shall be either electricity driven or diesel driven with direct flexible coupling.
14.3.5 The electric drive motor shall be squirrel cage induction conforming to IS325-1978 and rated
for continuous duty (S1). Motor shall have not less than class B insulation and minimum
enclosure of IP22. The starter shall be air-cooled fully automatic star delta or auto-transformer
type. Starters shall conform to BE 8544 and rated for AC- 3 duty conditions.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 373
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
MATERIALS OF CONSTRUCTION
Part Material
Casing Cast Iron
Impeller Bronze IS:318, Gr. LTB 2
Casing Wearing SS
Shaft AISI 410 / Stainless Steel
Shaft Sleeve S.S. 316
Stuffing Box Gland Packed
Pumps shall be provided with pressure gauge with isolation cock on the delivery side.
In case of motor driven pump the motor rating should be adequate to drive the motor rating
should be adequate to drive the pump at 150% of rated discharge.
The pump and its prime mover (Electric motor or Diesel Engine) shall comply with all the
equipment of the Rules of the Traffic Advisory Committee.
All pumps shall have positive suction & shall be provided with suction strainer of SS & CI bell
mouth.
14.3.7 The diesel engine shall be naturally aspirated (non- turbo charged) & electrically started. The
engine shall have a speed governor to regulate the rated rpm within 5% of its rated speed. The
engine shall be complete with starting batteries full-wave selenium rectifier charger, isolation
leads, mounting frame etc. Engine rating shall be same as for the electric motor.
Diesel engine shall have suitable no. of cylinders with individual heat assemblies. The engine
shall be water cooled and shall include heat exchanger and connecting piping strainer, isolating
pressure reducing valves, bye-pass line, exhaust pipe, silencer, day tank for fuel all
interconnected piping etc., complete in all respects.
Engine shall be direct injection type with low noise and exhaust omission levels,
The speed of engine shall match the pump speed for direct drive.
The engine shall be capable of being started without the use of the wicks, cartridge heater plugs
or either at engine room temperature of 4C and shall take full load within 15 seconds from the
receipt of the signal to start.
The engine shall effectively operate at 46C ambient temperature at 150 meter above mean sea
level.
Noise level of the engine shall not exceed 120 dB (free sound pressure) at 3 meters distance.
Engine shall be suitable for running on high speed diesel oil.
The system shall be provided with a control panel with push button starting arrangement also
wired to operate the engine on differential pressure gauge.
The entire system shall be mounted on a common structural base plate with anti-vibration
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 374
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
mounting, Dunlop make, and flexible connections on the suction and delivery piping.
Contractor provide one fully mounted and supported Day Oil Tank fabricated form 6mm thick
MS sheet electrically welded for 8 hours working load and having suitable capacity of oil.
Provide level indicators low level and full level in the Day Oil Tank on the control panel
through float switches and an breather. Day Oil Tank shall also be provided with filling
connection (Threaded) with cap, gauge glass indication and cocks, drain cock, inspection /
cleaning cover with gasket and nuts / bolts. MS dyke to hold 150% of the Day Tank capacity to
be built around the Day Tank.
Contractor to provide one exhaust pipe with suitable muffler (residential type) to discharge the
engine gasses to outside in open air as per site conditions (Contractor to check the site).
Contractor to provide all accessories, fittings and fixtures necessary and required for a
complete operating engine set. The exhaust pipe shall be taken outside the building with
minimum number of bends (approx. length 30 Meters) and shall be duly heat insulated with
50mm thick glass wool covered with 24 gauge aluminum cladding.
Contractor shall indicate special requirements, if any, for the ventilation of the Pump Room.
14.4 Jockey Pump & Booster pump
14.4.1 Starting and stopping of Jockey Pump set shall be automatic at predetermined levels through
pressure switch. However, arrangements for manual start and stop of the pump shall also be
made. Jockey Pump shall take care of small leakages in the piping system and pumps cushion
tanks. The Jockey pump shall be similar to the fire pump but need not have a split casing.
14.4.2 A Booster pump shall be provided (if called) at terrace to pressurize the wet riser system. The
pump shall be centrifugal mono-block type.
14.5 Accessories:
14.5.1 The fire and Jockey pumps shall be complete with the following accessories:
1) Suction and discharge eccentric reducers.
2) Pump coupling guard
3) Common base frame, fabricated mild steel or
Cast iron.
14.5.2 Each pump including jockey pump shall have independent set of pressure switches. The
pressure switch shall be snap action SP DT switch rated 10 A @ 220 V operated through a
stainless steel diaphragm. The switch shall have a pointer for manual adjustment of set point,
and all electrical connections shall be terminated in a screwed terminal connector. The entire
unit shall be encased in a cold drawn steel enclosure. The diaphragm shall be designed for a
maximum operating pressure of the system. Each pressure switch shall be provided with
pressure gauges and pressure switches shall be mounted on the pipeline.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 375
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
14.5.3 Flow switches shall be paddle type SPDT snap acting contacts rated 10 A @ 220 V. The
paddle shall be made of either brass or phosphor bronze terminated in a screwed terminal
connector. The entire unit shall be encased in cold drawn steel enclosure and the maximum
operating pressure of the parts in contact with the liquid shall be consistent with the system
pressure. 10 Kg/cm2.
Jockey pump shall start when the system pressure drops by 0.35 Kg/Sq. cm and stop when the
system pressure is reestablished.
The fire pump shall start when the system Pressure Drops by 1.0 Kg/cm2 and shall continue to
run till manually switched off.
Jockey and fire pump starting shall be indicated on the panel with a red indicating lamp. It
should also be indicated on the Main and Repeater Alarm Panels(MAP & RAP)
14.6.2 The electrical control panel shall be sheet steel enclosed dead front type with easy access to all
parts and cable terminations. The panel drawings shall be got approved before fabrication.
Panel shall be fabricated out of 14 SWG (2.0 mm) thick steel sheets duly rust inhabited through
a process of degreasing and phospating. The panel shall be complete with ON/OFF push
buttons, ammeters, indicating lamps etc. The under voltage protections shall not be provided
for fire pumps.
14.6.3 The motor starters (direct on line or star-delta or auto- transformer) shall consist of electrically
actuated contractors. The starter shall be complete with ON-OFF push buttons, timers and
auxiliary contracts and shall be fully automatic. There shall be an indicating lamp with each of
the pumps and an ammeter and selector switch with the fire pumps. Fire pump starting shall be
annunciated through an electric siren. Autotransformers shall be korndorfer type for smooth
transition. The autotransformer shall be oil/air cooled and shall have separate compartment in
the panel. In the case of combination fire hydrant and sprinkler systems, the control panel shall
cover the sprinkler pump starter, control components etc. complete as for fire pumps.
14.6.4 All cabling, to and from the pumps to starters and control switches shall be carried out through
armored PVC cables of approved makes. Cables shall be laid in accordance with section "M V
CABLING". The pump motors and panels shall be double earthen in accordance with IS 3043-
1956 or as shown on drawings.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 376
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The first aid hose shall conform to IS 884-1969 and be wound on a heavy-duty circular
hose reel with a cast iron bracket. The hose shall be permanently connected on one end to the
standpipe through a 20-mm G.M valve with necessary hose adopter and a gunmetal nozzle at
the other end. The reel shall swing out by 270 degree.
Canvas hoses shall be in two lengths of 7.5 m each, of flax or controlled porcelain type with
instantaneous couplings, neatly rolled into bundles and held in position with steel brackets.
Canvas hoses shall be tested and certified by the manufacturers, to withstand an internal water
pressure of not less than 35 Kg/sq. cm without bursting. The hose shall also withstand a
working pressure of 7 Kg/sq. cm. without leakage or undue sweating.
The hose cabinet shall be fabricated from 2-mm mild steel sheet duly rust inhibited through a
process of degreasing and phosphating. The cabinet shall have double flap-hinged doors with
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 377
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4mm clear glass and shall have necessary openings for riser main and brackets for all internals.
The cabinet shall receive two coats of red oxide primer both inside and outside before two after
coats of final paint of approved colour shade.
14.7.3 External Hydrants shall be stand post types over ground unless shown otherwise. All external
hydrants shall be 80-mm dia with instantaneous spring lock type and 80 mm C.I. Sluice valve.
Hydrants shall be located at least 2 M away from and within 15 m from the building wall.
Each hydrant shall be provided with a hose cabinet containing 2 x 15 m 63 mm dia. flax or
controlled percolation hoses with couplings. Wherever shown, the cabinet may contain a
branch pipe and nozzle. The cabinet shall be 900 x 600 x 400 fabricated out of 2-mm mild
steel sheet duly rust inhibited through a process of degreasing, phosphating etc. And fitted with
4 mm clear 400 x 400 glass window. The cabinet shall receive two coats of red oxide primer,
inside and outside, before 2 coats of final painting of approved shade. The cabinet shall be
wall- mounted or free standing with its own steel legs depending on the site conditions and as
shown on drawings.
14.7.4 The fire brigade connection shall consist of one or two twin-headed 63-mm dia gun metal
outlets with built-in check valve and drain plugs connected to a 150 mm dia outlet connection
to the water reservoir or to the hydrant main. The fire brigade collecting head shall conform to
BE 904-1965.
14.7.5 Priming:
A priming tank of the specified capacity shall be provided wherever shown on the drawings
and schedule of work. The tank shall be fabricated out of 4-mm mild steel sheets and painted
with epoxy based black paint. The tank shall be complete with 25 mm make up float valve
with PVC ball, 25 mm over flow and drain connections, 25 mm drain valve, gauge glass, 450
mm manhole with malaria proof cover, 50 mm vent with cowl and mosquito netting.
14.8 Piping:
All piping shall be as specified under "piping for Fire Fighting" and the schedule of work for
piping.
14.9 Testing & Commissioning:
All hydrant piping shall be tested for a hydrostatic test pressure of 30 Kg/sq. cm or 1.5 time the
working pressure (whichever is less) for a period of 24 hours at the end of which there shall be
no loss in pressure.
14.10 HOSES:
Hoses pipes shall be of fabric reinforced rubber lines as per IS:636 Type II or canvas hose as
per IS:4927, with nominal size of 63 mm and lengths of 15 meter or 7.5 meter, as per quantities
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 378
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
specified for in schedule or bill of quantity. All hose pipes shall carry ISI marking on the body
of the hose.
The hose shall have instantaneous spring lock-type coupling on ends.The instantaneous
coupling shall be as per IS:903. It shall be fixed to each other by copper rivets and galvanised
M.S. wires and leather bands. All coupling shall be interchangeable with each other, and shall
bear ISI markings.
14.11 Branch Pipes:
Branch pipe shall be of either gun metal or aluminium and should conform to IS: 903. One end
of the branch pipe will receive the coupling while the other end shall have a nozzle screwed to
it. It shall bear ISI marking.
14.12 Hose cabinet (hose Box):
Each hydrant shall be housed in a Hose cabinet of suitable size. The hydrant cabinet shall hold
twin headed hydrant, 2 hoses and one branch pipe as required. Internal hydrants shall normally
fit the size of the niche made for it. The cabinet shall be of minimum 14 SWG M.S. sheet with
centre opening, double glass front doors (cleat glass of 4mm thickness). The glass shall be
firmly fixed by means of steel clips and screw with rubber beading. Hinges shall also be
screwed and not welded. The corner members (frame) shall be of 25 x 25 x 3 mm thick angle.
The hose box shall be firmly fixed to the wall/support by means of brackets and dash fasteners.
The steel work shall have one coat of primer and two coats of red paint. The words Yard
Hydrant, Hydrant etc. should be painted in white or red on the glass in 75 mm high letters.
The hose box shall be lockable.
14.13 Air Cushion Tank:
Every wet riser shall be provided with an air cushion tank at its top most point. The air cushion
tank shall be provided with an automatic air release cock, 20 mm dia. drain pipe, drain valve
and shut off valve.
14.14 Fire Brigade inlet Connection:
A fire brigade inlet connection with a non-return valve shall be provided to facilitate the fire
brigade to pump water into the installation by the use of their own equipment. Four way or 150
mm dia connection to the system shall comprise of four instantaneous pattern 63 mm dia. male
inlets shall be with caps and chains complete with 150 mm dia. sluice valves, non-return valve
housed in a M.S. cabinet with glass fronted door. The cabinet shall be suitable for recess
mounting.
Two way or 100 mm fire brigade inlet connection to the system shall comprise of two
instantaneous pattern 63 mm dia. male inlets shall be with caps and chains complete with 100
mm dia sluice valve, non-return valve housed in a M.S. cabinet with glass fronted door. The
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 379
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
15 SPRINKLER SYSTEM
15.1 The scope of work shall cover supply, installation testing and commissioning of the sprinkler
system covering the following :
Sprinkler pumps, electric or diesel driven as shown in the equipment schedule.
Installation valve/s with motor-gong.
Sprinklers
Sprinkler piping
Branch flow switches connected to the building fire alarm system.
15.2 Standards
The sprinkler installation shall conform to and meet with the requirements set out by the
following :
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 380
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 381
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
assemblies comprising :
A mains gate valve
In and Out pressure gauge
Test connection of adequate size with valve and orifice plate with pressure connections.
Water meters and gongs with necessary piping, isolating valve and strainer and drain.
The installation valve shall be straight through type suitable for wet pipe sprinkler systems.
Valves shall be of cast iron with gunmetal internals and suitable for vertical or horizontal
installation. The valve clack shall be of cast gun metal with neoprene seal and retaining ring
and shall incorporate a suitable non-return device to compensate for pressure fluctuations
which should not mal-operate the clack. The gun metal internals shall provide for smooth
waterways for :
1) Water valve through a retard chamber
2) Test connection and drain.
15.12 There shall be two pressure gauges, one for the main side and another for the installation side.
Each gauge shall have pressure damping brass piping with gunmetal gauge and drain.
15.13 A test connection of adequate size as shown on drawings or as approved shall be provided with
a shut-off gate valve, an orifice plates with pressure connections. The discharge from the test
connection outlet shall be led to the nearest sump or drain as shown on drawings or as directed.
15.14 The mains water motor and going shall preferably be of cast gun metal body and internals. The
valve shall have an associated gunmetal gate valve, strainer preceding the water motor. The
water motor and gong shall be located on the discharge lead as shown in drawings or as
directed.
15.15 Flow switches shall be as specified under `Fire Hydrant System
15.16 Sprinklers Head:
15.16.1 Sprinklers shall be thermo-sensitive glass-bulb actuated type and to be standard products from
an established firm of repute and standing and approved by an appropriate authority for fire
fighting duty. Sprinkler heads shall be pendent/recessed, pendent, concealed, or sideway type.
15.16.2 All sprinklers shall be brass castings polished chrome or white (polyester) unless stated
otherwise and rated for 12.0 Kg/sq. cm WG and factory tested for 34.0 Kg/sq. cm. Sprinklers
shall be pendant or sideway type as specified and shown on drawings. All sprinklers shall be
provided with an adjustable escutcheon finished same as the sprinkler head. Wherever shown
and specified, sprinklers shall be recessed type.
15.17 Temperature classification of sprinklers in each space shall be as shown on the drawings.
Sprinklers shall be selected for the coverage shown on the drawings and ordinarily be 12/12
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 382
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
mm with K factor of 115 (metric). Wherever the specified sprinkler is not adequate, the
Tenderer may offer appropriate size required.
15.18 Piping:
15.18.1 All piping shall be mild steel medium duty as specified under "Piping for Fire Fighting".
Necessary line flushing valves shall be provided as shown on drawings or as required to.
15.19 Testing:
15.19.1 The entire sprinkler piping shall be tested, with the sprinklers in position, to a hydrostatic test
pressure of 13.8 Kg/sq. cm for a period of 48 hours at the end of which there shall be no loss in
pressure.
15.19.2 Test valves in each sprinkler installation shall be opened (with temporary drain
connection) and the following observations recorded :
1) Start-up of sprinkler pump
2) Operation of water meter gong
3) Operation of Flow Switch in the appropriate branch.
All branches shall be so tested and witnesses and attested by the Engineer-in-charge. All the
operating tests shall be carried out in the presence of any local authority, Fire Brigade or
Insurance Company.
By Pass connection with valves from electric or diesel driven both main fire Pump as shown in
Diagram.
Sluice Valve, Drain Valves at bottom of riser.
Drenchers
Drencher piping
16.2 Standards
The Drencher installation shall conform to and meet with the requirements set out by the
following :
IS 1648 1961 Code of practice for fire Safety of buildings
Fire Insurance Association of India - Tariff Advisory Committee rules.
Local Fire Brigade and Fire Engineering Authorities.
16.3 Source of water
The installation shall be connected to the existing Fire Hydrant pumps, with Sluice valve at
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 383
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
riser bottom & 50 mm (2") drain valve fully open between sluice valve & 1st drenchers.
16.4 Valve: The controlling valves shall be located in accessible positions. The Positions of each
valve & the drenchers it controls must be clearly indicated by a well-written signboard. Painted
in post office red paint.
16.5 Drencher Head:
16.5.1 Drenchers shall be standard products from an established firm of repute and standard and
approved by an appropriate authority for fire fighting duty.
16.5.2 All Drenchers shall be brass castings polished chrome or white (polyester) unless stated
otherwise and rated for 12.0 Kg/sq. cm WG and factory tested for 34.0 Kg/sq. cm. Drenchers
shall be walls or Curtain Drenchers type as specified and shown on drawings.
16.5.3 Spacing of Drencher heads: Drenchers shall be placed with maximum horizontal spacing of 2.5
meters C/C.
16.5.4 Piping
All piping shall be mild steel medium duty as specified under "Piping for Fire Fighting".
Necessary Valves & drain valves shall be provided as shown on drawings or as required to.
16.5.5 Operation: System shall be operated by the opening of main Sluice valve & closing of drain
valve located at bottom of the riser.
16.5.6 Drainage: In open drencher system, the drain valve shall always be kept open except when the
drenchers are in operation
16.5.7 Test Valve: A full way 50mm (2") dia. Valve and shall be provided below the controlling
valves, so that the running pressure test can be carried out at any time.
17.1 The hydrant pump starting and stopping shall be tested by opening the test valve and record
the following :
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 384
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
17.2 All the operating tests shall be carried out in the presence of any local authority. Fire Brigade
or Insurance Co.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 385
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
and branch pipe at (ii) above shall be opened. When the pressure has dropped by (-) 1.5
Kg/cm2, the electric main pump shall come into operation automatically. After the main pump
has run for 5 minutes, the power supply in the pump house shall be switched off. The diesel
pump shall automatically come into operation immediately.
18.9 All these tests mentioned above shall be repeated after one hour interval. The result of all the
tests shall be identical again. After the system has satisfactorily withstood the above tests, it can
be taken over from the contractor.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 386
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 387
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 388
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS 1239 Mild steel tubular and other wrought steel pipes and fittings (Part-II)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 389
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IS 778- 1984 Specifications for copper alloy Gate, Globe And Check Valves for water
supply purposes.
IS 1703 1977 Specification for ball valves (horizontal plunger type)including
floats for water supply purposes.
IS 3004 1979 Specification for plug cocks for water supply purposes.
IS 3950 1979 Specifications for surface boxes for sluice valves.
IS 9338 1984 Specification for cast iron screw-down stop valves and stop and check valves for
water works.
IS 4346 1982 Specification for washers for use with fittings for water
The material supplied shall comply with the latest applicable Indian and / or British Standards. Other
National Standards are acceptable, if they are established to be equal or superior.
services.
IS 5219 Part 1 Specification for cast copper alloy traps Part1 1982
IS 5312 part 1 Specification for swing check type reflux (Non-return) 1969 valve for
water works purposes part 1 single door pattern
IS 13049 1919 Diaphragm type (plastic body) float operated valve for cold water services
specification.
IS 13114 1991 Forged brass gate, globe and check valves for water works purposes
specification.
IS 14399 part 1 Hot press moulded thermosetting glass fibre reinforced & Part 1 1996
polyester (GRP) resin sectional water storage tanks.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 390
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Following [Table 8] are the standards and codes are made part of these specifications.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 391
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 392
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The pipes shall be galvanized mild steel `C' class Factory welded pipes and seamless, screwed
and socket tubes conforming to the requirement of IS 1239-1964 for Heavy grade. They shall
be of the dia. (nominal bore) specified in the description of the item. The sockets shall be
designated by the respective nominal bores of the pipes for which they are intended.
The pipes and sockets shall be clearly finished, well galvanized in and out and free from
cracks, surface flows, laminations and other defects. All screw threads shall be clean and well
cut. The ends shall be cut cleanly and square with axis of the tube.
All screw tubes & sockets shall have pipe threads conforming to the requirements of IS:
544-1955 (or revised) screwed tubes shall have threads while the sockets shall have parallel
threads.
The fitting shall be of malleable cast iron or MS. tubes complying with all the appropriate
requirements given in para 1.1.1 or as specified the fittings shall be designated by the
respective nominal bore of the pipes for which they are intended.
The fittings shall have screw threads at the ends conforming to the requirements of IS: 544-
1955(or revised). Female threads on fitting shall be parallel & male threads (except on
running nipples & collars of unions) shall be taper.
The pipes & fittings shall be inspected at site before use to ascertain that they confirm the
specification given in para 1.1.1 above. The defective pipes shall be rejected. Where the pipes
have to be cut or rethreaded, the ends shall be carefully filed out so that no obstruction to bore
is offered. The end of the pipes shall then be threaded conforming to the requirements of
IS544-1955 with pipe dies & taps carefully in such a manner as will not result in slackness of
joints when the two pieces are screwed together. The taps & dies shall be used only for
straightening screw threads which have become bent or damaged & shall not be used for
turning of the threads so as to make them slack, as the latter procedure may not result in water
tight joint. The screw threads of pipes & fittings shall be protected form damage until they are
fitted.
The pipes shall be cleaned & cleared of all foreign matter before being laid. In jointing the
pipes, the inside of the socket & the screwed end of the pipes shall be oiled &
rubbed over with white lead & a few turns of spun yarn wrapped round the screwed end of the
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 393
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
pipe. The end shall then be screwed in the socket, Care should be taken that all pipes & fitting
are properly jointed so as to make the joints completely water tight & pipes are kept at all time
free form dust & dirt during the fixing. Burr from the joint shall be removed after laying the
open ends of the pipes shall be temporarily plugged to prevent access of water, solid or any
other foreign matter. Any threads exposed after jointing shall be painted or in the case of
under ground piping thickly coated with approved anticorrosive paint to prevent corrosion.
For internal work the galvanized iron pipes & fittings shall run on the surface of the walls or
ceiling unless otherwise specified. The fixing shall be done by means of standard pattern holder
bat clamps, keeping the pipes about 1.5 cm clear of the wall. When it is found necessary to
conceal the pipes chasing may be adopted or pipes fixed in the ducts or recess etc. provided
there is sufficient space to work on the pipes with standard tools. The pipes shall not be
ordinarily be burried in walls or solid floors, where unavoidable pipes may be buried for
short distance provided adequate protection is given against damage & where so required
joints are not to be burried. Where directed by the Engineer-in-charge, a MS. tube sleeve shall
be fixed at a place a pipe is passing through a wall of floor for reception of the pipe & allow
freedom for expansion & contraction & other movements. In case the pipe is embedded in
walls or floors it should be covered with hessian cloth dipped in coal tar / Japan black (for cold
water pipes) and heat insulation to be provided for hot water pipes as per specification. The
pipe should not come in contact with lime mortar or lime concrete as the pipe is affected by
lime. Under the floors the pipe shall be laid in layer of sand filling done over concrete floors.
All pipes & fittings shall be fixed truly vertical & horizontal unless unavoidable. The pipes
shall be fixed to walls with standard pattern holder bat clamps of required shapes & size so as
to fit tightly on the pipes when tightened with screwed bolts.
These clamps shall be embedded in brickwork in cement mortar 1:3 (1 cement: 3 coarse
sand) & shall be spaced at regular intervals in straight lengths as shown in the table given
below.
Concrete walls / floors at no time shall be chiseled out or reinforcement exposed to lay the
pipes. The contractor shall use masonry drill to drill the hole and use anchor bolts to fix the
pipe.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 394
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
LENGTHS
SIZE OF PIPE HORIZONTAL RUNS VERTICAL
Mm. Meters RUNS meters
15 2 2.5
20 2.5 3
25 2.5 3
32 2.5 3
40 3 3.5
50 3 3.5
65 3.5 5
75 3.5 5
The clamps shall be fixed at shorter lengths near the fittings as directed by the Engineer-in-
charge. for G.I. pipes 15mm to 25 mm dia. the holes in the walls & floors shall be made by
drilling drill bits & not by dismantling the brickwork on concrete. However, for bigger
dimension pipes the holes shall be carefully made of the smallest size as directed by the
Engineer-in-charge. After fixing the pipes the holes shall be made good with cement mortar 1:3
(1 cement: 3 coarse sand) & properly finished to match the adjacent surface.
The galvanized iron pipes & fittings shall be laid in trenches. The widths & depths of the
trenches for different diameters of the pipes shall be as in the table given below:
DIA. OF PIPE WIDTH OF TRENCH DEPTH OF TRENCH
15 mm TO 50 mm 300 mm 60 cm
65 mm TO 100 mm 450 mm 75 cm
At joints the trench width shall be widened wherever necessary. The work of excavation &
refilling shall be done true to line & gradient.
The pipes shall be painted with two coats of Anti-corrosive bitumastic paint of approved
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 395
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
quality. The pipe shall be laid on a layer of 7.5 cm sand & filled upto 15 cm above the pipes.
The remaining portion of the trench shall then be filled with excavated earth. The surplus earth
shall be disposed off as directed.
In case of bigger diameter (65mm & above) pipes where the pressure is very high thrust
blocks of cement concrete 1:2:4: (1 cement: 2 coarse sand: 4 grade stone aggregate of 20 mm
nominal size) shall be constructed on all bends to transmit the hydraulic thrust without
impairing the ground & spreading it over a sufficient area.
After jointing, the pipes & the fittings shall be inspected under working conditions of pressure
& flow. Any joint found leaking shall be redone & all leaking pipe removed & replaced
without extra cost.
The pipe & fittings after they are laid shall be tested to hydraulic pressure of 6 Kg/cm2 (60
meter) The pipes shall be slowly & carefully charged with water allowing all air to escape &
avoiding all shocks of water hammer. The draw of taps & stopcocks shall then
be closed & specified hydraulic pressure shall be applicable gradually. Pressure
gauge must be accurate & preferably should have been recaliberated before the test. The test
pump having been stopped the test pressure should be maintained without loss for at least half
an hour. The pipes & fitting shall be tested in section as the work of laying proceeds, keeping
the joints exposed for inspection during the testing.
1.1.7 MEASUREMENTS: The lengths shall be measured in running meters correct to a cm. For the
finished work, which shall include G.I. pipes & G.I. fittings such as bends, tees, elbows,
reducers, crosses, plugs, sockets, nipples & nuts, but excludes brass or gun metal taps (cocks),
valves, lead Connection pipes & shower rose. The measurements shall be taken separately for
internal & external work. The length shall be taken along the central line of the pipe & fittings.
All pipes & fittings shall be classified according to their diameters, method of jointing &
fixing substance, quality & finish. The diameter shall be the nominal diameter of the internal
bore. The pipes shall be described as including all cuttings & waste. In case of fittings of
unequal bore, the largest bore shall be measured.
INTERNAL WORK: The rate for internal work shall include the cost of labour & material
involved in all the operations described above except in para 1.1.5 unless otherwise specified.
The rate shall include the cost of cutting holes in walls & floors & making good the same.
This shall not however include concealed pipe work.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 396
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1.7a GI PIPES & FITTINGS: The pipes shall be of the class specified in the Schedule of Quantities
& shall be of galvanized steel, welded or seamless, screwed & socketed shall conform to IS:
1239. & they shall be manufactured by a firm of repute. All fittings shall be malleable iron
galvanized fittings of approved best Indian make. The detail of the pipes regarding nominal
bore thickness & weight are given below:
SCREWED
APP. &
NOMINAL SCREWED & SOCKETED
OUT SOCKETED
BORE METERS / 1000 KG.
SIDE Wt/Mtr
DIA.
MM NEAREST LIGHT MEDIUM HEAVY HEAVY MEDIUM LIGHT Kg.
inch Kg. Kg. Kg. Kg. Kg.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 397
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
SCREWED
APP. &
NOMINAL SCREWED & SOCKETED
OUT SOCKETED
BORE METERS / 1000 KG.
SIDE Wt/Mtr
DIA.
MM NEAREST LIGHT MEDIUM HEAVY HEAVY MEDIUM LIGHT Kg.
inch Kg. Kg. Kg. Kg. Kg.
101.6 90 3 8.92 9.90 11.800 112 101 84.6
NOTE: The above weights are for black pipes & theoretical weights of galvanized pipes are 6% higher.
1.1.7b WATER PRESSURE MAINS: Shall be conform to IS: 1536-11967 Class L A as specified in
the schedule. They shall be laid, jointed & tested along with the C.I pipes as described in the
specification for C.I.S/S pipes.
1.1.7c FLANGED PRESSURE MAINS: Flanged joints to be made by painting the face of the flanged
with red lead freely & bolting up evenly on all sides.
A thin fiber of lead wool shall be used in making the joints water tight where facing of the
pipes is not true.
Where packing may be used, it shall be of rubber insertion cloth three ply & of approved
thickness. The packing should be of full diameter of the flange with proper pipe hole &
bolthole, neat & even at both the inner & outer edges.
Where the flange is not fully faced, the packing may be of the dimension of the facing strip
only. Its proper placing should be tested before another pipe is jointed on.
TESTING: After each section of the pipeline has been completed it shall be tested for
water tightness before being covered in. This can be done by closing by means of a valve,
blank flange, cap or plug & fill the pipe with water. The pressure should be raised by means of
a small hand operated pump till it registers 50% above the highest working pressure in the
section & the test pressure should be assertained by means of a reliable gauge. When the pipe
is laid on any appreciable gradient, the test should be carried out at the lower end of the
section. Any leaking joints should be made good & the above test reapplied until no further
leaks are apparent.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 398
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The rate for external work shall include the cost of labour & materials in all the
operations described above except in para 1.1.4. The rate shall include excavation trenches,
painting of pipes & sand filling all around the pipes, unless specified otherwise, for which
separate payment shall be made.
1.2.1 Materials Pipes & Fittings-para 1.1.1 & 1.1.2 shall apply
1.2.2 Preliminary work - A pit of suitable dimensions shall be dug at the point where the connection
is to be made with the main & earth removed up to 15cm below the main. The flow of water in
the water main shall also be disconnected by closing the sluice wheel valves on the mains.
1.2.3 Making connections - For cutting & jointing para 1.1.3 shall apply. The G.I main shall
be cut. Water if any collected in the pit shall be bailed out & ends of the G.I. pipe threaded.
The connection of distribution pipe shall then be made by fixing malleable G.I. Tee of the
required size & fitting such jam nuts, G.I. sockets, connecting piece etc.
1.2.5 The portion of the pipe in the pit shall be painted with bitumastic paint & encased with sand
15cm allround. Pit shall be filled with earth in level with original ground surface watered,
rammed & the area dressed.
1.2.6 Measurements The work of making connections to kitchen & laundry equipments should be
counted in numbers.
1.2.7 Rate the rate shall include the cost of labour & materials involved in all the operation
described above.
1.3 Fixing water meter & stop cock in G.I. Pipe line:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 399
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.3.2 CUTTING G.I. PIPE LINE: The G.I. line shall be cut to the required length at the position
where the meter & stopcocks are required to be fixed. The ends of the pipe shall then be
threaded. For cutting & threading the pipe, para 1.1.3 shall apply.
Fixing meters & stop cock: The meter & stopcock shall be fixed in position by connection
pipes, GI Jam nut, & socket etc. The stopcock shall be fixed near the inlet of the water meter.
The paper disc inserted in the nipples of the meter shall be Removed & the meter installed
exactly horizontal or vertical in the flow line in the direction shown by the arrow cast on the
body of the meter. Care shall be taken that the factory seal of the meter is not
disturbed. Wherever the meter shall be fixed to a newly fitted pipeline, the pipeline shall have
to be completely washed before fitting the meter. For this purpose a piece of pipe equal to the
length of the meter shall be fitted in the proposed position of the meter in the new pipeline.
The water shall be allowed to flow completely to wash the pipeline & then the meter installed
as described above by replacing the connecting piece.
Testing of joints:
1.4 FITTINGS:
General - The brass or gunmetal fittings shall be heavy quality & approved manufacture &
pattern with screwed or flanged ends as specified. The fittings shall in all respects comply with
the Indian standard Specifications NO.IS>778-1957 & IS.781- 1959. The standard size
of brass gunmetal fittings shall be designated by the nominal bore of the pipe outlet to which
the fittings are attached. A sample of each kind of fittings shall be got approved from
the Engineer-in-charge & all supplies made according to the approved samples.
1.4.1 All cast fittings shall be sound & free from laps, blowhole's holes & fittings; both internal &
external surfaces shall be clean, smooth & free from sand etc. Burning plugging, stopping or
patching of the casting shall not be permissible. The bonnets, spindles & other parts shall be
truly machined so that when assembles the parts shall be axial, parallel & cylindrical with
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 400
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
A bibcock (bib tap) is a draw off tap with a horizontal inlet & free outlet & stopcock (stop tap)
is a valve with a suitable means of connections for insertion in a pipeline for controlling or
stopping the flow. They shall be specified size & shall be of screw down type. The closing
device should work by means of a disc carrying a renewable non-metallic washer, which shuts
against water pressure on seating at right angles to the threaded spindle, which operates it. The
handle shall be either crutch or butterfly type securely fixed to the spindle. Valve shall be
of the loose leather seated pattern. The cocks taps) shall open in anti-clockwise
direction. The bibcocks & stopcock shall be polished brass. The minimum finished weights
of the bib tap (cock) & stop tap (cock) as given in the IS.
8 0.25 0.25
10 0.30 0.35
15 0.40 0.40
20 0.75 0.75
When the bib cocks or stop cocks are required to be chromium plated, the chromium plating
shall be of grade B type conforming to IS: 1068-1958. The chromium shall never be deposited
on brass unless coating of nickel is interposed. In case these are required to be nickel plated,
the plating shall be of first quality with a good thick deposit of silvery whiteness capable of
taking high polish which will not easily tarnish or scale. In finished & appearance, the plated
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 401
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
articles, when inspected shall be free from plating defect such as blisters, pits, roughness &
unplated areas & shall not be stained or discoloured. Before a plate is plated the washer plate
shall be removed from the fittings. The gland packing shall be protected from the plating
solution.
Gun metal bibcocks & stopcock: These shall be of gunmetal screw down pattern of the size as
specified. So far as the general requirements of materials are concerned, these shall be similar
to those as described in para 1.5.2. The weight of these shall be the same as for brass bibcocks
& as described in para 1.5.2.
Full way valve is a valve with suitable means of connection for insertion in pipeline
for controlling or stopping the flow. The valve shall be of brass fitted with a cast iron
wheel & shall be of gate valve type opening full way of the size as specified. Valve shall be
of best quality as approved by the Engineer-in-charge & shall have the following
approximate weight with a tolerance of 5%
These shall be of the Gunmetal fitted with wheel & shall be of Gate valve type opening
full way & of the size as specified. These shall generally conform to IS.778-1957 their
approximate weights shall be given in para 1.5.1.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 402
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Ball valve: The ball valve shall be of high-pressure class & shall be of sizes as specified.
The nominal size of a ball valve shall be that corresponding to the size of the pipe to which
it is fixed. The ball shall be of brass or Gun metal as specified, & the float of copper sheet.
The minimum gauge of copper sheet used for making the float shall be 45 for float upto
115mm dia. & 55 for float exceeding 115mm dia. This shall be sphercial in shape. The
jointing of the float shall be made by efficiently burnished, lapped & soldered seam or by
bracing. Plastic float may also be used if specified. The body of ball valve when assembled
in working conditions with the float immersed to not more than half of its volume
shall remain closed against a test pressure of 10.5Kg/sq. Cm. & low pressure shall against a
test pressure of 3.5Kg/sq. cm.
The ballvalve shall generally conform to ISI Specifications No 1703-1962. The weight of
ball cock & the size of ball shall be as per table given below.
1.7 CAST IRON & SPUN IRON PIPES & FITTINGS:
1.7.1 MATERIALS:
Pipes & specials: The cast iron pipes shall confirm to ISI 1537-1960 while spun iron pipes
shall conform to IS 1536- 1960. They shall be either with spigot & socket ends or flanged
ends. The cast iron pipes shall be vertically either class A or B as specified. The spun iron
pipes shall be of the cast iron casted centrifugally & shall be of class A, B as specified in the
item. These pipes & specials Shall be used for water pressure upto half of the hydraulic test
pressure of various pipes as given below:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 403
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Upto & including 300 mm. 20(200) 25(250) 30(300) 20(200) 25(250)
Specials: The specials shall conform to IS. 1538-1960 & shall be of medium or heavy class depending on
their thickness. The hydraulic test pressure of each class shall be as follows:
All the cast iron pipes shall be capable of easily working a drill or file. Pipes & specials should be sound
with smooth inner & outer surface, neatly dressed & carefully fitted free from laps Pinholes, & other
imperfections & shall ring clearly when struck with a light hammer. The end of the pipes &the specials
shall be reasonably square to their axis.
All pipes & specials before they are affected by rust shall have been coated with approved anti-corrosive
treatment or by heating & dipping in Dr. Agnus Smith's solution at the factory.
1.7.1 Stacking:
The pipes & specials shall be handled with sufficient care to avoid damage to them.
These shall be lined up on one side of the alignment of the trench, socket facing uphill or in
the direction of flow of water.
1.7.2 Trenches for C.I. Pipes & Specials:
The trenches for pipes shall be excavated to lines & levels as directed. The bed of the trench
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 404
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
shall have to be truly & evenly dressed throughout from one change of grade to the next. The
gradient is to be set out by means of bending rods & the required depth of excavated at any
point to the trench shall be regarded as directed by the Engineer-in-Charge. The depth of the
trench shall not be less than meter measured from the top of the pipe to the surface of the
ground under road & not less than 0.75m elsewhere. The bed of trench, if soft or made up of
earth, shall be well watered and rammed before laying the pipes & the depressions if any
shall be properly filled with earth & consolidated. If the rock is met with, it shall be removed
to 15 cm. below the level of the pipe & the trench will be refilled with excavated materials &
consolidated. The excavated materials shall not be stacked within meter or half of the trench
width whichever is greater from edge of the trench. The materials excavated shall be
separated & stacked so that in refilling they may be re-laid & compacted in the same order to
the satisfaction of the Engineer-in-charge. The trench shall be kept free from water. Shoring
& timbering shall be provided wherever required. Excavation below water table shall be
done after dewatering the trenches.
After tie excavation of the trench is completed, hollows shall be cut at the required positions
to receive the socket of the pipes & these hollows shall be sufficient depth to ensure that the
barrels of the pipes shall rest throughout their entire length on the solid ground & that
sufficient space left for jointing the underside of the pipe joint. These socket holes shall be
refilled with sand after jointing the pipe where the pipe line or drain crosses an existing road,
the road crossing shall be excavated at a time, the second half being commenced after the
pipes have been laid in the first half & the trench refilled. Necessary safety measure for
traffic as directed shall be adopted. All types of pipes, water mains, cables, etc. met within
the course of excavation shall be carefully protected & supported. Care shall be
taken not to disturb the electrical & communication cable removal of which if necessary shall
be arranged by the Engineer-in-charge.
Before being laid the pipes shall be examined to see that there are no cracks or defects as
described in para 1.7.1.1 above. Subjected to the approval of the Engineer-in-charge, the
damaged portion of the cracked pipe may be cut at a point not less than 15 cm. beyond the
visible extremity of the crack. The pipes shall be thoroughly cleaned of all dust & dirt &
special care shall be taken to clean the inside of the socket & outside of the spigots.
The pipes shall be lowered into the trench by means of suitable pulley blocks, sheer ropes
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 405
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
etc. In no case the pipes shall be rolled & dropped into the trench. After lowering the pipes
shall be arranged so that the spigot of one pipes shall be carefully centered into the socket of
the next pipe & pushed to the full distance that it can go. The pipe shall be laid to the levels
required. Specials shall also be laid in their proper positions as stated above.
Where so directed, the pipes & specials may be laid on masonry or concrete pillars. The pipe
laid on the level ground shall be laid with socket facing the direction of water. In all other
cases, the socket shall be laid facing up hill.
Any deviation either in plan or elevation less than 11% shall be effected by laying the
straight pipes round a flat curve, of such radius that minimum thickness of lead at the face of
the socket shall not be reduced below 6mm or the opening between spigot & socket increased
beyond 12mm at any point. A deviation of about 2% can be effected at each joint in this way.
At end of each days work, the last pipe laid shall have its open last ends securely closed
with a wooden plug to prevent entry of water, soil, rats and any other foreign matter into the
pipe.
Cement concrete thrust blocks of suitable design as approval by the Engineer-in-charge shall
be provided at 45 & 90 deg. bends of the pipes & also at places where there is likelihood of
thrust so as to withstand the dynamic & static forces developed due to water in the pipe line.
The thrust blocks shall be made after the joints have been tyton.
The excavated earth shall be spread in the layer of 250mm. thickness and shall be compacted
by proper watering. This filling shall be done such that the joints remain completely open for
working. Rest of the filling shall be done in the manner after the line is satisfactorily tested.
The excavated material such as brickbats, asphalts cracks, shall be properly arranged in the
top most layer of 23cm & shall be consolidated thoroughly. The excess material shall be
spread over the surrounding ground in the radius of 50M from the point of excavation. If
extra earth for complete filling will be necessary, same shall be brought from other places by
the contractor at his full cost, & the same shall be filled up into the trench as per the manner
shown above.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 406
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Sluice valves: The sluice valves are used in a pipeline for controlling or stopping flow of
water. These shall be specified of size and class and shall be of non-rising screwed type with
either double flange or double socket ends & cap or hand wheel. These shall, in all respects,
comply with the Indian standard specifications IS.780-1963 for valves upto & including
300mm. size. Classes 1 sluice valve is used for maximum working pressure of 10Kg/cm (100
meter head) & Class 2 sluice valve for 15Kg/cm (150 meter head).
The body, domes, covers, wedge gate stuffing box shall be of good quality cast iron, the
spindle of bronze, and the nut & valve seats leaded tin bronze. The bodies spindle & other
parts shall be truly machined with surface smoothly finished. The area of the water way of
the fittings shall be not less than the area equal to the nominal bore of the pipe.
The valves shall be marked with an arrow to show the direction of turn for closing of the
valve.
The valve shall be fully examined & cleared of all foreign matter before being fixed. The
fixing of the valve shall be done by means of bolts, nuts & 3mm rubber insertion of
chemically treated compressed fibber board 1.5mm minimum thickness & of weight less than
0.183 gm/sq. cm. with flanges of spigot & socketed tail pieces drilled to the same
specification in case of S & S pipes & with flanges in case of flanged pipes. The tail pieces
shall conform to IS. 1938-1960. These shall be jointed to the pipeline by means of lead
caulked joints.
The hydrant shall be fully examined and cleared of all foreign matter before being fixed. The
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 407
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
fixing shall be done on the water main, which shall be on minimum 75mm dia. The flanged
end of the hydrants shall be fixed to the flanged out let of a tee in the water main by means of
blots, nuts & 3mm rubber insertion of or chemically treated compressed fibber bore 1.5mm
minimum thickness & of weight not lees than 0.183 gm. Per sq. c.m. This can also be fixed
by means of flanged tail piece, which may be connected to the water main by C.I. specials.
1.8.3 Appurtenances:- The other appurtenances of pipe line are mentioned below:-
Air Valves: These are placed at every summit in the pipe line to permit the escape of air
when the main is filled, & afterwards if any air is carried into the mains. These are also
placed on long stretches of nearly level main.
Scour Valves: These are placed at bottom of the all depressions of pipes for emptying the
main or letting out the sediment.
Reflux Valves: These are fixed so as to open in the direction of flow but automatically to
close if the water flows back. They are used to diminish the damage done by the escape of
water due to a burst or to prevent damage to impellers of Pump.
Safety or Relief Valves: These are fixed at the down stream ends of long lengths of
main or where water hammer may take so as to reduce from any excessive pressure to the
nominal if it occurs.
1.8.4 Measurements: the valves, fire hydrants & tail pieces shall be enumerated separately unless
other wise specified, under relevant items.
1.8.5 Rate: The rate shall include the coast of materials & labour, profit etc. involved in all the
operations described above against relevant items of work.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 408
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
C.I. surface boxes shall be coated with black bituminous composition except in the case of
fire hydrants where the cover of the surface box shall be painted with two coats of rust
resisting bright luminous yellow paint for clear visibility during night. The C.I. surface box
shall be fixed on the top of the masonry chamber and provided with plain or reinforced
cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal
size.)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 409
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 410
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.10.5 TESTING THE JOINTS: After jointing, the pipes & the fittings shall be inspected under
working conditions of pressure & flow. Any joint found leaking shall be redone & all
leaking pipe removed & replaced without extra cost.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 411
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The pipe & fittings after they are laid shall be tested to hydraulic pressure of 6 Kg/cm2 (60
meter) The pipes shall be slowly & carefully charged with water allowing all air to escape &
avoiding all shocks of water hammer. The draw of takes & stop cocks shall then be closed &
specified hydraulic pressure shall be applicable gradually. Pressure gauge must be accurate &
preferably should have been recalibrated before the test. The test pump having been stopped
the test pressure should be maintain without loss for at least half an hour. The pipes &
fitting shall be tested in section as the work of laying proceeds, keeping the joints exposed for
inspection during the testing.
2.0 DRAINAGE:
UPVC Drainage class pipes of Foamcore Astral (SN 8) or equivalent make in solvent
2.1A cement joint including leveling with cutting the pipe to required length, roughining of
pipe for external sewer drain.
2.1 Stoneware pipes with spigot & socket ends shall conform to IS.651-1965 and shall be of
grade A or AA as specified. These shall be sound, free from visible defects such as dire
cracks or hair cracks. The glaze of the pipe shall be free from crazing. The pipe shall give a
sharp clear note when struck with a light hammer. There shall be no broken blisters. The
approximate thickness of 600 mm long pipes shall be given in the table.
Internal dia. of the pipe Thickness of the barrel & of socket Weight of each Pipe per M.
Mm mm Kg.
100 12 14
150 16 22
200 17 33
230 19 44
250 20 52
300 25 79
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 412
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The length of pipes shall be 60 cm. exclusive of the internal depth of the
socket. The pipes shall be handled with sufficient care to avoid damage to them.
2.1.1 Trenches for stone ware pipe drains:
Para 1.7.2 under subhead `water supply' shall apply. Wherever the drain runs deeper the
width of trench in the upper reaches shall be increased as directed by Engineer-in-charge.
2.1.2 Laying of stoneware Pipes:
All pipes shall be laid on a bed of 15cm. Cement or lime concrete as specified projecting
on each side of the pipe to the width of the trench specified in para 1.7.2. The pipes with
their crown level at 1.20 M. depth & less from ground shall be covered with 15 cm. thick
concrete above the crown of the pipe & sloped off to meet the outer edges of the concrete to
give a minimum thickness of 15 cm. All around the pipe. Pipes laid at a depth greater than
1.20 M. at crown shall be concerted at the sides upto the level of the center of the pipe &
sloped off from the edge to meet the pipe tangentially.
The pipes shall be carefully laid to the alignments, levels & gradients as shown on the plans
and sections. Great care shall be taken to prevent sand etc. From entering the pipes. The
pipes between two manholes shall be laid truly in a straight line without vertical or horizontal
undulation. The pipes shall be laid with socket up the gradient. The body of the pipes shall
for its entire length rest on an even bed of concrete.
Where they are not bedded on concrete the trench floor shall be left slight high & carefully
bottomed up as pipe laying proceeds. So that the pipe barrels rest on firm & undisturbed
ground. If the excavation has been carried out too low, the desired levels shall be made up
with concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size)
for which no extra cost shall be paid. If the floor of the trench consist of rock or very hard
ground that cannot easily be made to a smooth surface the pipe shall be laid on a leveling
course of concrete as described.
2.1.3 Jointing: Tarred gasket of hemp yarn soaked in thick cement slurry shall first be placed round
the spigot of each pipe & the spigot shall then be slipped home well into the socket of the
pipe previously laid. The pipe shall then be adjusted & fixed in a correct position & the
gasket caulked tightly home so as to fill not more than 1/4 of the total depth of the socket.
The remainde of the socket shall be filled with stiff mixture of cement mortar in the
proportion of 1:1(1 cement: 1 fine sand) When the socket is filled, a sillet shall be forged
round the joint with a trowel forming an angle of 45 deg. with the barrel of the pipe. After a
day's work any extraneous material shall be removed from the inside of the pipe. The newly
made joints shall be cured.
2.1.4 Testing of joints: Water Test: Stoneware pipes used for sewers shall be subjected to a test
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 413
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
pressure of 1.5 M. head of water at the highest point of the section under test. The test shall
be carried out by suitably plugging the low end of the drain and the ends of the branch
connection if any and filled the systems with water. A knuckle bend shall be temporarily
jointed in at the top end and a sufficient length of vertical pipe jointed to it so as to plugged
with a connection to a hose ending in a funnel which could be raised or lowered till the
required head is obtained & fixed suitable for observation. Where leakage is visible the
defective part of the work shall be got out and made good.
2.1.5 Refilling of trenches: Clause 1.7.5 under water supply shall apply. In case where pipes are
not bedded on concrete special care shall be taken in refilling trenches to prevent the
displacement and subsequent settlement at the surface resulting in uneven street surfaces and
dangers to foundations etc. The back-filling materials shall be packed by hand under &
around the pipe & rammed with a shovel & light tamper. This method of filling will be
continued upto the top of the pipe. The refilling shall rise evenly on both sides of the pipes
continued upto 60 cm. Above the top of the pipe so as to not to disturb the pipe.
The reminder of the back - filling shall not be done until 7 days have elapsed for brick sewers
and 14 days of concrete sewers, unless local condition or materials are suitable for the earlier
placing of a load on the pipes. The tamping shall become progressively heavier as the depth
of the backfill increases.
2.2 S.W.GULLY TRAP: Gully traps shall conform to IS.651-1965. This shall be around, free
from visible defects such as fire cracks or hair cracks. The glaze of the traps shall be free
from crazing. They shall give a sharp clear note when struck with light hammer. There
shall be no broken blisters. The size of the gully trap shall be as specified and all dimensions
will be as per drawing. Each gully trap shall have one C.I. grating of square size
corresponding to the dimensions of inlet of gully trap. It will also have a watertight C.I.
cover with frame inside dimension 300 X 300 mm. the cover weighing not less than 2.72
KG. The grating cover & frame shall be of sound & good casting & shall have square seating
faces.
2.2.1 Excavation: The excavation for gully traps shall be done true in dimensions & levels as
indicated on plans or as directed by the Engineer-in-charge.
2.2.2 Fixing: The gully trap shall be fixed on cement concrete foundation 65cm. square & not less
than 10 cm. thick. The mix for concrete will be 1:5:10(1 cement: 5 fine sand: 10 aggregate
40mm nominal size). The jointing of gully trap outlet to the branch drain shall be done
similar to jointing of S.W. pipe as directed in clause 2.1.3.
2.2.3 Brick masonry chamber: After fixing & testing gully & branch drain, a brick masonry
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 414
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
chamber 300 X 300 mm.(inside) in second class bricks in cement mortar 1:5(1 cement : 5
fine sand) shall be built with a 10 cm brick work round the gully trap from the top of the bed
concrete upto ground level. The space between the chamber walls & the trap shall be filled
in with cement concrete 1:5:10(1 cement: 5 fine sand: 10 grade stone aggregate 40 mm
nominal size). The upper portion of the chamber i.e. above the top level of the trap shall be
plastered inside with cement mortar 1:3(1 cement: 3 coarse sand) finished with floating coat
of neat cement. The cement corners & bottom of the chamber shall be rounded off as to slope
towards the grating. C.I. covers with frame 300 X 300mm (inside) shall then be fixed on top
the brick masonry with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone
aggregate 20mm. nominal size) & rendered smooth. The finished top of cover shall be built
about 4 cm. above the adjoining ground level so as to exclude the surface water from
entering the gully trap.
2.3 CEMENT CONCRETE PIPES:
The pipes shall be with or without reinforcement as required & of the class as specified.
These shall conform to IS.458-1961. The reinforced cement concrete pipes shall be
manufactured by centrifugal (or spun) process. All pipes shall be true to shape, straight,
perfectly sound & free from cracks & flaws. The external & internal surface of the pipes
shall be smooth & hard. The pipes shall be free from imperfect grading of the aggregate
mixing or moulding. The pipes shall be RCC light duty, NP2 type.
Concrete used for the manufacture of reinforced concrete pipes & collar shall not be leaner
than 1:2:4 (1 cement: 2) poarse 4 graded stone aggregate). The max. size of aggregate
should not exceed 1/3 of the thickness of the pipe or 20 mm whichever is smaller. The
reinforcement in the reinforced concrete pipes shall be extended throughout the length of the
pipe. The circumfrential & longitudinal reinforcements shall be adequateto with stand
hydrostatic pressure & further bending stresses due to the weight of water when running full
across the spun equal to the length of pipe plus 3 times it's own weight.
2.3.1 Trenches for concrete pipe: Para 1.7.2 shall apply. Where the pipe shall be bedded directly
on soil, the bed shall be suitably rounded to fit the lower part of the pipe.
2.3.2 Laying of pipes: Loading, transportation & unloading of concrete pipes shall be done with
care. Handling shall be such as to avoid impact. Gradual unloading by inclined plane or chain
block is recommended. All pipe sections & connections shall be inspected carefully before
being laid. Broken or defective pipes or connections shall not be used. Pipes shall be lowered
into the trenches carefully. Mechanical appliances may be used Pipes shall be laid true to line
& grade as specified. Laying of pipes shall proceed upgrade of a slope.
If the pipes have spigot & socket joints, the socket end shall face upstream. In the case of
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 415
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
pipes with joints to be made with loose collars, the collars shall be slipped on before the next
pipe is laid. Adequate & proper expansion joints shall be provided where
directed. Incase where the foundation conditions are unusual such as in the proximity of
tress, of holes, under existing or proposed manholes, etc. the pipe shall be encased all-round
in 15 cm. thick cement concrete 1:3:6(1 cement: 3 fine sand: 6 graded stone aggregate 40
mm nominal size) or compacted sand or gravel.
In case where the natural foundation is inadequate the pipe shall be laid either in concrete
cradle supported on proper
Foundations or on any other suitably designed structure. If a concrete cradle bedding is used
the depth of concrete below the bottom of the pipe shall be least 1/4th of the internal dia. of
the pipe subjected to the min. of 10 cm. & a max. of 30 cm. The concrete shall be extended
upto the sides of the pipe atleast to a distance of 1/4th of the outside diameter or pipes 300
mm. & over in dia. The pipes shall be paid in this concrete bedding before the concrete
has set. Pipes laid in trenches in earth shall be bedded evenly & firmly & as far as the
branches of the pipes as to safely transmit the load excepted from the backfill through the
pipe to the bed. This shall be done either by excavating the bottom of the branch to fit the
curve of the pipe or by connecting the earth around the curve of the pipe to form an even bed.
Necessary provision shall be made for joints wherever required. When the pipe is laid in
trench in rock hard clay, shale or other hard material the space below the pipe shall be
excavated & replaced with an equalizing bed of concrete sand or compacted earth.
When the pipes are laid completely above the round the foundation shall be made even &
sufficiently compacted to support the pipeline without any material settlement. Alternatively
the pipeline shall be supported on rigid foundations at intervals. Suitable arrangements shall
be made to retain the pipeline in the proper alignment such as by shaping the top of the
supports to fit the lower parts of the pipe. The distance between the supports shall in no case
exceed the length of the pipe. The pipe shall be supported as far as possible close to the
joints. In no case shall the joint come in center of the spun. Care shall be taken to see that
super imposed loads greater than the total load equivalent to the weight of the pipe when
running full shall not be permitted.
Suitable designed anchor blocks at change of direction & grade for pressure lines shall be
provided where required.
2.3.3 Jointing of pipes: Joints are generally of rigid type. Where specified flexible type joints may
also be provided.
Spigot & Socket joint (rigid): The spigot of reach pipe shall be slipped home well into the
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 416
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
socket of the pipe previously laid & adjusted in the correct position. The opening of the joint
shall be filled with stiff mixture of cement mortar in proportion of 1:2(1 cement: 2 fine sand)
which shall be rammed with caulking tool. After a days work any extraneous material
shall be removed from inside of the pipe & the newly made joint shall be cured.
Collar joint (rigid): The adjoining pipes shall be butted against each other in correct position.
The collar shall then be slipped over the joint, covering equally both the pipes. The angular
space shall be filled with stiff mixture of cement mortar 1:2 (1 cement: 2 fine sand) which
shall be rammed with caulking tool. After a days work any extraneous materials shall be
removed from the inside of the pipe & the newly made joint shall be cured.
2.3.4 Testing of joints, refilling of trenches: Clause 2.1.4 and 2.1.5 shall apply for stoneware &
concrete sewers.
Manholes 1.4M internal diameter at bottom is generally constructed for drainage works
where depth is 2.45M or more. When manholes are constructed on foot path, they shall be
provided with cover of medium duty casting & when built within the width of the road under
vehicular traffic, these shall be provided with cover of heavy duty casting.
Excavation: The manholes shall be excavated true to dimensions & levels shown on the
plans or as directed by the Engineer-in-charge.
Bed concrete: The manholes shall be built on a bed of cement concrete 1:4:8(1 cement: 4
coarse sand: 8 graded stone aggregate 40mm nominal size). The thickness of the bed
concrete shall be of 20cm. For manholes upto 4.25 M depth & 30 cm. for depths beyond
4.25M manholes otherwise specified or directed by Engineer-in-charge.
Cement block work shall be within mortar 1:5 (1 cement: 5 fine sand). The external joints of
the pipe with the masonry shall be made perfectly leak-proof for circular manholes. Masonry
in arches & arching over the pipes shall be in cement mortar 1:3(1 cement: 3 fine sand). The
coarse of manholes of circular type the excess shaft shall be corbelled inwardly on three sides
at the top to reduce it's size to that the cover frame to be fitted. The walls shall be built of
20cm. Brick work for depth upto 4.25 M below depth 4.25 M in ordinary sub soil
wall thickness shall be increased to 30 cm. & at 9.75 M below ground 40 cm. shall be built.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 417
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Plaster & painting: The walls of the manholes shall be plastered inside with 12mm. thick
cement plaster 1:3 (1 cement: 3 coarse sand) finished smooth. In the case of arched type
manhole the walls of the manhole shall be plastered inside all around only upto the crown
level, & flush pointed for the shaft with cement mortar 1:2(1 cement: 2 fine sand). Where the
saturated soil is met with, also the external surface of the walls of the manhole shall be
plastered with 12 mm. thick cement plaster 1:3(1 cement: 3 coarse sand) finished smooth
upto 30 cm. above the highest sub-soil water level, with the approval of the Engineer-in-
charge where required. The plaster shall further be water proofed, with addition of approved
water proofing compound in a Quantity as per manufacturer specifications and Instructions.
Benching: The channels and benching shall be done in cement concrete 1:2:4(1 cement:
2coarse sand: 4 graded stone aggregate 20 mm nominal size) and rendered smooth with neat
cement.
The depth of channels & benching shall be as in the table given below:
Top of channel at the center in Depth of benching at side wall in cm. above
Size of drain in mm.
cm. above bed concrete bed concrete
100 15 29
150 20 30
200 25 35
250 30 40
300 35 45
RCC Work: RCC work for slabs & lintels shall be in cement concrete 1:2:4 (1cement:
2coarse sand: 4graded stone aggregate 20mm. nominal size) with steel reinforcement. Plain
concrete where for fixing the frame of manholes covers shall be of 1:2:4 mix (1cement:
2coarse sand: 4graded stone aggregate 20 mm nominal size). This concrete shall be laid in
one operation integral with RCC slab underneath.
Foot rests: All manholes deeper than 1.2M shall be provided with M.S. foot rests. Footrests
shall be of 20mm. M.S. Square or round bars as specified. These shall be embedded 20 cm.
deep with 20 X 20 X 10 cm. blocks of cement concrete 1:3:6(1 cement: 3coarse sand:
6graded stone aggregate 20cm. nominal size). The block with M.S. footrest placed its center
shall be cast in site along the masonry & surface finished with 12 mm. thick cement plaster
1:3 (1cement: 3coarse sand) finished smooth.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 418
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Footrests shall be fixed 30cm. apart vertically & shall project 10cm. beyond the surface of
the wall. The top footrests shall be 45 cm. below the manhole cover. Foot rests shall be
painted with coal tar, the portion embedded in the masonry or cement concrete block being
painted with thick cement slurry before fixing.
Manhole covers & frames: The covers & frames shall conform to IS: 1726-1960 & shall be
of the following grade and types:
Heavy duty: These shall be denoted by the letters `HD' circular solid type for use
under heavy vehicular traffic conditions.
Medium duty: These shall be denoted by the letters `MD' circular or rectangular solid type
for use under light traffic conditions such as foot paths, carriage drives & cycle tracks.
b. Light duty: These shall be denoted by the letters `LD'
Or rectangular size for use in domestic premises of
Where they are not subjected to wheeled traffic loads.
The covers & frames shall be neatly cast & they shall be free from air & sand holes & from
cold shuts. They shall be nearly dressed & carefully trimmed. All castings shall be free from
voids whether due to shrinkage gas inclusion or other causes. Covers shall have a raised
checkered design on the top surface to provide an adequate non-slip grip.
The covers shall be capable of easy opening & closing & it shall be fitted in the frame in
workmanship like manner. The cover shall be gas tight & watertight.
The size of covers specified shall be taken as the clear internal dimensions of the frame.
The approximate weights of the various types of manhole covers & frames shall be as in table given
below:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 419
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Covers and frame shall be coated with a black bituminous composition. The coating shall be smooth
tenacious. It shall not flow when exposed to a temperature of 63 deg. & shall not be brittle as to chip off at
temperature of 0 deg. C.
The frame of manhole cover shall be firmly embedded to correct alignment & levels in RCC slab or
plain concrete, as the case may be on the top of the masonry.
After completion of the work, manhole covers shall be sealed by means of thick grease.
2.4.1.1 Filling Earth: The excavated earth shall be back filled around the manhole as the brickwork
proceeds. The surplus earth shall be disposed off as directed by the Engineer-in-charge or as
specified.
2.4.2 Drop Connection: In case where branch pipe sewer enters the manhole of main sewer, a
drop connection should be provided. S.C.J pipes & specials conforming to IS.1729-1964 as
revised from time to time shall be of the size same as of the branch pipe sewer.
For 150 & 250 mm. main line. The difference in level between the water line (peak-flow-
level) & the invert level of branch line is less than 60 cm. a drop connection may be provided
within the manhole by giving ramp. If the difference in level is more than 60 cm. the drop
should be provided externally.
Excavation: The excavation shall be done for the drop connection at the place where the
branch line meets the manhole. The excavation shall be carried upto the bed concrete of the
manhole & to the full width of the branch line.
Laying: At the ends of branch sewer line S.C.I. tee shall be fixed to the line, which shall be
extended through wall of the manhole by horizontal piece of S.C.I. pipe form an inspection
on cleaning eye. The open end shall be provided with chain & lid. The S.C.I. drop pipe shall
be connected to the tee at the top & to the S.C.I. bend at the bottom. The end shall be
extended through the wall of the manhole by a piece of C.I. pipe, which shall discharge into
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 420
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
the channel. Necessary channel shall be made with cement concrete 1:2:4(1 cement: 2coarse
sand: 4graded stone aggregate to 20 mm nominal size) & finished smooth to connect the
main channel. The joint between S.C.I. pipe & fittings shall be lead caulked. The joint
between S.C.I. tee & S.W. branch line shall be made with cement mortar 1:1(1 cement: 1 fine
sand) as per para 2.1.3 for SW pipes. The exposed portion of the drop connection shall be
encased allround with minimum 15cm. Thick concrete 1:3:6 (1 cement: 3 fine sand: 6 graded
stone aggregate 40 mm nominal size) & cured. For encasing the concrete around the drop
connection, necessary centering & shuttering shall be provided. The holes made in the walls
of manholes shall be made good with brick work in cement mortar 1:5(1 cement: 5 fine
sand) & plastered with cement mortar 1:3(1 cement: 3 coats sands) on the inside of the
manhole wall. The excavated earth to be backfilled in the trench in level with the original
ground level.
2.5 SOIL, WASTE, RAIN WATER, VENT & ANTI-SIPHONAGE PIPE & FITTINGS:
2.5.1 All soil, waste, vent and anti-siphonage pipes & fittings used within plumbing shafts (vertical
run) shall be sand cast iron socket & spigot conforming to IS. 1729-1964 or its subsequent
revision. All cast iron pipes & fittings shall be of the best approved Indian make or soil
variety preferably of spun quality & hot dipped in Dr. Agnus Smith Solution & free from
flaws. Air bubbles, cracks, sandholes & other defects and shall be truly cylindrical &
uniform in thickness. They shall not be brittle but shall allow for heavy cutting, chipping &
drilling & shall not be less than 6mm thick & the diameter mentioned in the schedule of
qualities & shall be of the largest length available & shall be fixed against the wall on special
`U' clamps 25mm wide, 3mm thick & hot dip galvanised by means of round headed flat nail
of 75mm long on brickwall. In case of hollow block wall 50 X 50 X 75mm long wooden
gutties soaked in solignum should be first fixed & then flat nails should be based & nails
painted with two coats of paint.
2.5.2 Jointing shall be carried out with Drip seal. The spigot of the pipe must be forced well home
into it's socket & must be entered, so that the joint may be of even thickness all round.
Atleast, one complete lap of clean white hemp spun yarn shall be drawn into the socket
without being forced through the joints into. As many laps as may be needed to leave the
space of not less than 25 for the drip seal shall then be poured into the joint. The joints shall
then be run with drip seal in sufficient quantity so that after being caulked solid, the drip seal
may project 3mm beyond the face of the socket against the outside of the spigot but must be
flush with the outside edge of the socket.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 421
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.5.3 Cleanouts at the head of CI SS horizontal pipes running under the floor shall be of cast brass
screwed in type. Floor & wall clean outs shall be of cast brass screwed type. The connecting
pieces shall be of G.I. threaded to suit the Clean out with lead caulked joint.
2.5.4 Inspection chambers, gully traps, etc. within the building shall be of `Patel Pattern' cast iron
with bolts, nuts to close the cover, all to be fabricated as per actual requirements.
2.5.5 Supports, pedestals & base for inspection chambers, gully traps & pipes shall be in 1:2:4
cement concrete mixes.
2.5.6 Pipe sleeves & inserts, etc. through RCC walls either external or internal shall be C.I. or M.
S. provided with water bar flange.
2.5.7 During installation open end of pipes shall be plugged with wood cut into required shape
of gunny bags & to be maintained free from dirt.
2.5.8 G.I waste pipes & fittings shall be of `C' class I.T.C. or equivalent with G.I. unions, tail piece
reducers & connections to be provided between joints to either lead or C.I. Pipes.
2.5.9 The sizes of branch waste pipe for different fittings shall be as follows :
Lavatory Basin - 1 1/2" & 1 " dia.
Urinal - 1 1/2" dia. (40 mm)
Sink - 1 1/2" dia. (40 mm)
Nahni Trap - 3" dia. (75 mm)
Special floor Trap - 75 or 100 mm as required
with bolted aluminum
grating in 25 X 25 mm
M.S. angle.
2.5.10 W.C. pan connectors shall be to suit the requirements as per drawing, with 40mm vent born
for connections to he anti-siphonage pipe with pan connector of C.I. lead.
2.5.11 Connection to the sewage or storm water collection sumps to be perfectly water tight & as
specified in the drawing.
2.5.12 Rain water flashing shall be of 150mm X 100mm or 225mm X 150mm with C.I. dome shape
grating & extension piece.
2.5.13 All rain water pipes & fittings shall be soil pipe variety conforming to IS. 1729-1964 or
equivalent. This shall apply to pipe outside buildings or within the building or separate
shafts.
2.5.14 The floor trap for toilet blocks shall be cast iron with C.I. brass grating, bolted down design.
2.5.15 Where toilet shafts are sunk, the floor trap shall be of 100 mm X 75 mm heavy type C.I. `P'
Trap, with C.I. brass grating, bolted down design.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 422
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.5.16 Bathroom C.P. grating shall be of bolted down design out of heavy cast brass with the
chromium plating of the best approved standard.
2.5.17 Cast iron gratings shall be flat with perfect edge of the quality procurable of the specified
width & thickness & the available lengths.
2.5.18 Spigotted & socketed 75 mm,100 mm & 150 mm C.I. pipes shall be of heavy pattern for
the portion below the floor & embedded & laid over 150 mm cement concrete 1:3:6, the
width of the concrete being :
75 mm dia
100 mm dia
150 mm dia
200 mm dia
The pipes shall be laid to a slope & connected to the drain. On no account should lime or
lime concrete come in direct contact.
The pipes shall be handled with sufficient care to avoid damage to them.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 423
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.6.3 Laying of P.V.C. Pipes: All pipes shall be laid on a bed of 15cm. cement or lime concrete as
specified projecting on each side of the pipe to the width of the trench specified in para 1.7.2.
The pipes with their crown level at 1.20 M. depth & less from ground shall be covered with 15
cm. thick concrete above the crown of the pipe & sloped off to meet the outer edges of the
concrete to give a minimum thickness of 15 cm. all around the pipe. Pipes laid at a depth
greater than 1.20 M. at crown shall be concerted at the sides upto the level of the center of the
pipe & sloped off from the edge to meet the pipe tangentially.
The pipes shall be carefully laid to the alignments, levels & gradients shown on the plans &
sections. Great care shall be taken to prevent sand etc. from entering the pipes. The pipes
between two manholes shall be laid truly in a straight line without vertical or horizontal
undulation. The pipes shall be laid with socket up the gradient. The body of the pipes shall for its
entire rest on an even bed of concrete & places shall be excavated in the concrete to receive the
socket of the pipe. RCC Hume pipe sleeve shall be provided for crossing the roads & drainage.
Where they are not bedded on concrete the trench floor shall be left slight high & carefully
bottomed up as pipe laying proceeds. So that the pipe barrels rest on firm & undisturbed ground.
If the excavation has been carried out too low, the desired levels shall be made up with concrete
1:5:10(1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) for which no extra
cost shall be paid. If the floor of the trench consist of rock or very hard ground that cannot easily
be made to a smooth surface the pipe shall be laid on a leveling course of concrete as described.
2.6.4 Cut the pipes as square as possible. The pipe & the socket should be clean & dry. Clean the
surface with emery paper before jointing.
Apply a thick coat of solvent cement on the outer surface of the pipe & also on the inner surface
of the socket.
Insert the pipe into the socket & turn it through a 90 d. angle for even distribution of cement.
Hold the joint for 2 minutes & ensure that pipe does not slip out of fitting. Clean off extra
cement. Let it dry.
2.6.5 Testing of joints: Water Test: PVC pipes used for sewers shall be subjected to a test pressure of
1.5 M. head of water at the highest point of the section under test. The test shall be carried out by
suitable plugging the low end of the drain & the ends of the connecting if any & filled the
systems with water. A bend shall be temporarily jointed in at the top end & a sufficient length of
vertical pipe jointed to it so as to plug with a connection to a hose ending in a funnel which could
be raised or lowered till the required head is obtained & fixed suitable for observation.
Where leakage will be visible the defective part of the work shall be got out & made good.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 424
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.6.6 Refilling of trenches: 1.7.5 under water supply shall apply. In case where pipes are not bedded on
concrete special care shall be taken in refilling trenches to prevent the displacement &
subsequent at the surface resulting in uneven street surfaces & dangers to foundations
etc. The backfilling materials shall be packed by band under & round the pipe & rammed with a
shovel & light tamper. This method of filling will be continued upto the top of the pipe. The
refilling shall rise evenly on both sides of the pipes continued upto 60 cm. Above the top of the
top of the pipe so as to not to disturb the pipe. The reminder of the backfilling shall not be done
until 7 days have elapsed for bricksewers & 14 days of concrete sewers, unless local condition or
materials are suitable for the earlier placing of a load on the pipes. The tamping shall become
progressively heavier as the depth of the backfill increases.
2.7 PVC (SWR) SOIL,WASTE,RAIN WATER,VENT & ANTI-SIPHONAGE PIPE & FITTINGS:
2.7.1 All Vent pipes and fittings used horizontal & vertical run shall be PVC (SWR) type Supreme /
Prince make smooth & free from air bubbles, cracks, & other defects truly cylindrical & uniform
in thickness. Pipe shall be of the largest length available & shall be fixed against the wall with
PVC clips nail of 75mm long on brick wall and suspended from ceiling by MS hangers &
Anchor fasteners or by welding to embedded plates. In case of hollow block wall 50 X 50 X
75mm long wooden gutties soaked in coligum should be first fixed & then flat nails should be
based & nails painted with two coats of paint.
2.7.2 Jointing of PVC Pipes shall be carried out with lubricated in Rubber lubricant) `T' shaped
Rubber rings as follows :
Make sure the spigot end & inside of socket is clean, & the Sealing ring is placed evenly in the
socket.
When cutting pipes make sure they are cut straight. Chamfer the end cut to a angle of 15% with a
medium file.
A correct depth of entry of the spigot into the socket is required to allow thermal movement. To
achieve this, push spigot fully into the socket (remove sealing ring at this time) & make a mark
on the spigot. Withdraw the spigot by 100 mm & mark the spigot with a bold line. This bold
mark indicates the correct depth of entry to allow the Necessary expansion gap.
Smear rubber lubricant evenly on the chamfered spigot & the sealing ring. Then insert the spigot
into socket with light twisting motion. (Ensure the 10 mm expansion gap is allowed)
Joining to CI pipes shall be in 1:1 cement sand joint after roughening the surface of
PVC pipes for proper hold.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 425
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Provide proper solid angle iron/channel section, supports for all pipes complete with clamps.
wherever insulation comes, to provide wooden guide to support pipe on the angle iron
hangers/supports. For attachment in concrete, use Dash" fasteners or anchor plug type inserts or
equivalents. Provide hangers within 0.9 meter of all hangers in direction of mains & a minimum
of three hangers per expansion bend wherever shown in drawing. Provide all
additional structural steel angles, channels or other members not specifically shown but are
required for proper support. Do not expose concrete reinforcement to hang pipes.
3.2 Where necessary additional hangers to be provided to arrest water hammers or hydraulic
resonance with proper rubber padding.
3.3 Space hangers, as noted below, except on all soil pipe which shall have a hanger or multiple
fittings , sufficient hangers shall be provided to maintain proper slop without sagging, in case of
slopping suspended line, the following is suggested.
A Pipe Sizes. Hanger Rod Dia.
20 mm through 50 mm 9 mm.
65 mm through 125 mm 12 mm.
150 mm and over 16 mm.
B Pipe sizes Spacing of Supports
12 mm to 20 mm 1.5 M apart
25 mm to 40 mm 1.8 M apart
50 mm & above 1.8 M apart or as per IS.
3.4 Provided floor stands, wall brackets of masonry piers, etc. for all lines running near the floor or
near walls for those lines can be properly supported from the walls or floors. Pipe line near
concrete or masonry walls may be hung also by hangers carried from wall brackets at a higher
level than pipes. Hanging of any pipe from another is prohibited.
3.5 HANGERS : Clevis or band type hangers shall be provided. Hot water piping is to be provided
with suspended supports as far as possible. Note that strap hangers are not permitted & clamps
should be of removable type.
3.6 INSULATED HOT WATER PIPING : A 40 mm thick timber support for direct support of hot
water line is required. Timber supports are to rest in brackets.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 426
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4.1 Pressure gauges shall have not less than 112 mm dia brass body siphon & gauge cock of 9 mm
size. Dial ranges shall be adequate for the pressure encountered & as specified.
4.2 Provided valves on branch pipe connection to mains & at connection to equipment where
indicated. All valves are to be located for easy access & are to be full bore of pipe connected
together. Support all valves wherever necessary. Valves are to be as per IS. 780 (class 1) for G.I.
sluice valve & to IS. 778 for valves & tested & approved.
4.3 VALVE SCHEDULE:
4.4 All globe & check valve shall have working parts suitable for hot & cold water, oil or gas as
required. Valves shall be tagged with permanent label under band wheel indicating type of
duty.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 427
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Unless otherwise specified, the sanitary fixtures shall be of the following specifications:
5.1.1 WATER CLOSETS : (European type) shall be of vitreous china of approved pattern, quality
& colour. The closet shall be fixed with C.P. brass screws in floor for floor mounted type &
mounted on C.I. chair brackets with bolts for wall mounted type & shall be provided with solid
plastic seat & cover with chrome plated pillar brass hangers as specified.
5.1.2 Indian Pattern shall be of similar quality as specified above. The pan shall be 675/575 mm in
length with `S' or `P' trap of the same material of the pan. The W.C. with the trap shall be fitted
& fixed in position & built round solid with brick & cement to required level after all
connections are made. The finished floor of the water closet shall be of 25 mm below the level
of the room or passage in front of it.
5.1.3 Both type of closets should conform to the requirements of I.S. 771-1963 for glazed vitreous
china sanitary appliances.
5.1.4 The flushing cisterns shall conform to the requirements of I.S. 774-1971. High level cisterns
shall be of cast iron unless otherwise specified. Low level cisterns shall be of the same material
as the water closet. The cisterns shall be mosquito proof & shall fulfil the requirements of the
local Authority.
5.1.5 The flush pipe shall be 32 mm dia. PVC if concealed & if exposed brass C.P. as specified.
5.1.6 Where flush valves are specified, this shall be of the best approved quality procurable with C.P.
control valve & C.P. flush pipe.
5.2 URINALS:
5.2.1 Urinals shall be of glazed fire clay earthenware or Vitreous china as specified & shall conform
the requirements of I.S. 771-1963. Bowl type urinals with a lipped basin & flushing main shall
be fixed to wall by screws. A 40 mm trap shall be provided & outlet shall be connected to soil
pipes.
5.2.2 One gallon flushing cistern shall be provided unless otherwise specified. In case of such urinals
in range one 3 gallons flushing cistern for 3 urinals shall be provided. All exposed pipe work
shall be heavy brass C.P. with C.P. wall supports.
5.3 LAVATORY BASIN:
5.3.1 They shall be of vitreous china of approved pattern & shall conform to the requirements of
Indian standard Specifications. The basin shall be provided with 32 mm heavy cast brass
C.P. trap & waste shall be connected to the waste pipe with a C.P. extension & wall flange.
5.4 SINKS:
5.4.1 They shall be of Vitreous china & shall strictly be in conformation with I.S. 771-1963 for
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 428
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6. INSULATION:
1. SCOPE:
Scope of this section comprises supply & installation of insulation for pipes, tanks & heat
exchangers as herein specified.
2. The insulation material shall be resin bounded fibber glass having following :-
a) Minimum density - 32 KG./C.M.
b) Thermal Conductivity - 0.04 KCAL/MH 0C
c) Minimum fiber dia. - 7 micrometer.
It shall be non-hygroscopic, Vermin proof & should not settle due to vibration over a period of
time.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 429
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
7.1 Cutting, patching & repairing required for the proper installation & completion of the work,
specified in each division, including chasing, plastering, masonry work, concrete work, etc. &
making good shall be carried out by the contractor wherever required. Holes , which are cut
oversize, shall be refilled, so that a tight fit is obtained around the pipe or other object passing
through. Any damages to water proofed location should not be patched up, without rectification
by the water proofing agency(specialist contractor) to ensure his guarantee.
8 EQUIPMENT PROTECTION:
.
8.1 Keep all the pipe & conduit openings closed by means of plugs or caps to prevent the entrance
of foreign matter. Protect all piping, conduit, fixtures, equipment or apparatus. Any such items
damaged prior to final completion or work shall be restored to its original conditions or replaced
at no expenses to the Owner.
8.2 ACCESSIBILITY:
The installation of valves, thermometers, cleanout fittings & other including equipment or
specialties requiring frequent reading, adjustments, inspections, repairs, removal or replacement,
shall be conveniently & accessibly located with reference to the finished buildings. hermometers
& gauges shall be installed so as to be easily read from the floor.
8.3 INSERTS & SLEEVES:
a) General: Layout work in advance of placing of concrete slabs or construction of walls, furnish &
set inserts & sleeves necessary to complete the work, cost of cutting or patching made necessary
as a result of this operation shall be at no expense to the Owner. Openings shall be as per
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 430
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
b) Pipe sleeves:
Wall Sleeves: G.I. wall sleeves in cold store & black pipe `A' class for cable, conduits, gas
pipes, etc. are to be inside flush with wall on both sides. Sleeves shall be large enough in
diameter to provide 12mm clearance around pipe for insulation. Exterior wall sleeves for cable
entry/pipe/earthing strips, etc. shall be cast-iron flush with wall on both sides. Sleeves shall be
large to allow caulking from cutside using lead wool.
Floor Sleeves: Interior floor sleeves for general areas shall be of C.I. extending 50mm(2") more
above finished floor. All pipes passing through sleeves shall be caulked with asbestos rope &
finish with cement mortar. Insulated pipe shall have insulation butted to floor sleeve & sealed
with insulating cement in both sides.
Exception: Chilled water or refrigerant suction piping insulation shall be run continuous through
the sleeves & caulked. Interior floor sleeves for kitchen areas shall be C.I. steel pipe extending
50mm(2") above finished floor. Caulking shall be the same for general areas. Floor co grade
sleeves, caulked & made water tight.
9.1 Determine that each piece of equipment meet the detailed requirements of the contract
documents & that it is suitable for the installation shown. Notify the Architect of any
shortcoming found during the tendering period. Each piece of equipment furnished shall meet all
detailed requirements of the contract documents. Equipments not meeting all
requirements will not be acceptable, even though specified by name along with other
manufacturers.
9.2 Where two or more units of the same class of equipment are furnished use product of the same
manufacture, component parts of entire system need not be product of the same manufacturer.
Furnish all materials & equipments, new & free from defects & of size, make, type, & quality
herein specified or approved by the Architect. All shall be installed in a neat & mark manlike
manner.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 431
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
10.1 Plumbing equipment fixtures, piping etc. shall be free of stampings, makings (except those
required by codes) iron cuttings & other foreign materials.
10.2 Hot,Cold & drinking water system shall be cleaned thoroughly filled & flushed with water.
10.3 The entire mechanical apparatus shall operate at full capacity without objectionable noise or
vibrations.
10.4 Test all plumbing system in the presence of the site Engineer/Supervisor/Engineer-in-charge &
ample advance notice to test dates. Provide all equipment materials & labour necessary for
inspection & tests & repair all work, not passing the tests. After repairs are made, repeat tests
until units system is found satisfactory, to the authorities. Carry out tests prior to concealing,
insulating or back filling over any piping No exceptions will be made.
10.5 Test entire system of soil, waste & vent piping by water after the roughing in is completed &
before the fixtures are set. After setting the fixtures, providing smoke test, after sealing all traps.
10.6 Water test: Test entire system or section of system by closing all opening in piping except the
highest opening & filling system with water to the point of overflow. If the system is tested in
sections, plug each opening except the highest opening of the section filled with water. Keep the
water in system or in portion under test of or atleast 45minutes before inspection starts with test
pressure/head lasting for two hours. The system must be tight at all joints.
10.7 Final Test: After fixture are set, test system with smoke as follows:-
10.8 Smoke Test : Fill traps with water, then introduce into system a pungent thick smoke produced
by one or more smoke machines. Then smoke appears at stacks on the roof, plug stacks & allow
pressure of 25mm water column to build up in system. Maintain pressure of 15 minutes before
inspection starts. The system shall be tight at all joints.
10.9 Test all down spouts or rain headers & their branches within the building by water as described
for the above soil, waste & vent system.
10.10 All water piping: Hydro-static test 150 PSI for a minimum of 2 hours without drop in pressure as
required.
10.11 All tests on below grade lines shall be continued until backfilling on such lines is completed to
disclose any damage caused by backfilling.
10.12 All system shall be tested in sections as required to expedite the work on other trades & meet
construction schedules & final test on completion.
11.1 The contractor at his own cost & charge shall provide all materials, tools tackle measure,
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 432
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
scaffolding labour & water necessary for the completion of the whole work in all respects.
The contractor shall pay the fees for testing the material if directed by the architects & Local
Authorities or other statutory authorities.
The Contractor will obtain, from time to time, various permission & the completion certificates
as per rules of all local & statutory authorities.
The Counter shall arrange for the material & storage facility with the building contractor.
Any materials, brought at site, shall not be removed without the written authority of the
Architect/Consulting Engineer/ Engineer-in-charge & when the Contractor shall have
received payment in respect of any unfixed materials on the work has been taken into account,
such materials, shall become the property of Employer/Corporation & the Contractor shall be
liable for any loss or damage hereto.
The Contractor shall insure the work against damages, for such sum as the
Architects/Consulting Engineers/Engineer-in -charge may from time to time direct. All
insurance policies are to be taken out in the joint name of Employer/Corporation &
the Contractor in an office selected by the Architect/ Consulting Engineer/Engineer-in-charge &
all policies & receipts shall be deposited with Architect/Consulting Engineers/Engineer-in-
charge.
All the brackets & hangers for pipes shall be fixed to the wall or RCC slab using `Dash' fasteners
wherever necessary.
The amount shown against the provision item or / and contingencies in the schedule are
provisional & for estimating purposes only the Contractor is neither concerned for its execution
nor to change any commission on these items. The Owner reserves the right to get the work done
for these items through a separate & independent Contractor.
Surplus material from the site shall be carted away by the Contractor without any cost to the
Employer / Corporation & the Storage shall be handed over to Employer /Engineer-in-charge
clean & ready for occupation.
There shall be maintained in a readily accessible place first aid appliance including adequate
supply of sterilized dressing & cotton wool.
All injured persons hall be taken to a public hospital without loss of time, in case where the
injury necessitates hospitalisation.
Suitable & strong scaffolds should be provide for workman for all works that cannot safely be
done from ground.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 433
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
No portable single ladder shall be over 8 M in length. The width between the side rails shall be
not less than 30cm. (clear) & the distance between two adjacent rungs shall not be more than
30cm. When a ladder is used or extra mazdoor shall be engaged for holding the ladder.
The excavated material shall not be placed within 1.5 M of the edge of the trench or half
of the depth of trench whichever is more. All trenches & excavation shall be provide with
necessary fencing & lighting.
Every opening in the floor of a building or in working platform be provided with suitable means
to prevent the fall of person or materials by providing suitable fencing or railing whose
minimum height shall be one meter.
No floor or other part of the structure shall be so overloaded with debris or materials as to render
it unsafe.
Workers employed on mixing & handling material such asphalt cement mortar or concrete &
lime mortar shall be provided with protective footwear & rubber hand gloves.
Those engaged in welding works shall be provided with welders protective eye-shields &
gloves.
.
No paint containing lead or products shall be used except in the form of paste or readymade
paint.
Suitable face masks should be supplied for use by the workers when the paint is applied in the
form of spray or surface having lead paint dry rubbed & scrapped.
Overalls shall be supplied by the Contractor to the painter & adequate facilities shall be provided
to enable the working painters to wash during the periods of cessation of work.
Hoisting machines & tackle used in the works. including their attachments, anchorage &
supports shall be perfect condition.
The rope used in hoisting or lowering material or as a means of suspension shall be of durable
quality & adequate strength & free from defect.
13.1 The pumps shall confirm to IS 1520-1960 (latest revision) and shall be of following
construction.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 434
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
13.5.0 Testing:
13.5.1 Tenders shall submit the performance curves of the pumps supplied by them. (They shall also
check the capacity and total head requirements of each pump to match his own piping and
equipment layout.)
13.5.2 On completion of the entire installation, pumps shall be tested, wherever possible, for their
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 435
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
discharge head, flow and B.H.P. Where it is not possible, at least the discharge and B.H.P as
measured on the input side shall be field-tested. Test results shall correspond to the
performance curves.
13.5.3 Tenders shall furnish the required testing instrument and arrange for their connection as
required.
13.6.0 Painting:
After complete installation and testing, pumps accessories and fittings shall be given two
coats three mills each, of approved finishing paint.
13.7.0 Bill of Material:
13.7.1 The bill of material given here are only for the pump sets and diesel engines. The contractor
shall include all ancillary item given in the specification and also these items which are
essential for efficient operation of the equipments.
13.8.0 Diesel Operated Pump sets:
13.8.1 General: The diesel engine and pump shall be a factory assembled and tested set, the
product of one manufacturer only as follows:
a) Ashok Leyland, Kirloskar or Kirloskar Cummins or approved quality. Provide the
necessary controls and accessories for a complete system.
13.8.2 Rating: Rating of the diesel engine set shall be based on operation of the set when equipped
with all necessary operating accessories such as air cleaners, lubricating oil pump, fuel
transfer pump, fuel injection pump, jacket water pump governor, etc.
13.8.3 Engine Specifications:
Type: Engine shall have compression ignition. It shall be a two or four stroke cycle, coiled
injection engine of either vertical inline or V types.
Horse Power: B.H.P shall be as per bill of quantities at 1000 rpm. Submit certified engine
horsepower curve showing the manufacturer's approval of the engine rating for standby
application.
Speed: The engine speed shall not exceed 1000 rpm at full load operation.
Fuel: The engine shall be capable of satisfactory performance on a commercial grade of
distilled petroleum fuel oil (such as No.2 fuel oil)
Governor: The engine speed shall be governed by a full hydraulic governor, woodward SS
or equal to maintain governed speed.
Fuel System: Per manufacturer's normally used system, including a fuel pump to lift the
fuel from the main tank and a replicable element fuel filter conveniently located for
servicing. Build a fuel tank of sufficient capacity into the engine base to provide an
immediate fuel supply to the pump upon engine start up. An engine-driven fuel pump shall
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 436
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Starting: Equip engine with a 24 volt electric starting system of sufficient capacity to crank
the engine at a speed, which will allow full diesel starting of the engine. Provide lead acid
batteries having sufficient capacity for cranking the engine for atleast 60 seconds at firing
speed, with capacity for starting the diesel engine a minimum of our times. Provide a suitable
battery trickle charger with sufficient capacity to re-charge batteries back to normal starting
requirements quickly. Provide an automatic battery trickle charger (6-amp capacity) to
maintain batteries at full capacity.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 437
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
pipes conforming to ASTM F441 Schedule 80 shall be threaded. No threading of CPVC pipes
Schedule 40 will be allowed.
14.4 CPVC Solvent Cement Specifications:
The CPVC solvent cement used for installing CPVC piping systems shall conform to ASTM
F493. For FlowGuard ipes from upto 2 pipes and fittings, a single step medium bodied
CPVC solvent cement should be used. For Corzan CPVC pipes and fittings upwards of 2,
a primer shall be used followed by a heavy bodied solvent cement conforming to ASTM
F493. PVC solvent cement should not be used.
14.5 Installation procedure:
All parameters pertaining to the installation of CPVC plumbing system such as cutting,
joining, support spacing, expansion loops, insulation, type of support, special connections,
etc. shall be as per the manufacturers specifications. For special considerations, Noveon
technical cell to be contacted for further details.
14.6 Special fittings :
All special fittings and accessories like internally or externally threaded brass adaptors, ball
valves, globe valves, unions shall be of CPVC.
14.8 Treatment for external exposed piping :
All external CPVC pipes shall be coated with an acrylic water based paint.
14.9 Insulation :
Insulation for the concealed CPVC pipes shall be glass wool, asbestos rope or nitrile rubber
based
15 SPECIFICATION FOR PP-R (PP-RANDOM COPOLYMER) PIPES
15.1 MATERIAL: Pipe manufactured as per DIN 8079 & 8077 And fittings as per DIN 16893.
Green colour for concealed application & Sky blue colour with UV protection for outdoor
application.
15.2 POLYFUSION WELDING : Joints of the indo green pipes & fittings are usually jointed
together by poly-fusion welding which is a fundamental property of this system. This
process consists of mixing of melted material of external surface of the pipe & internal
surface of the fitting, after heating them up to 2600C 100C on the small welding machine
called poly-fusion device. Fusion process gives homogeneous, integral, long lasting, leak
proof joints.
15.3 CUTTING: Cut the pipe square to the required length by cutter. Debur the cut end if
necessary. Pipe ends must be clean cut at right angles.
15.4 CLEANING: Prior to welding, the pipe & fitting should be dried & properly cleaned.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 438
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
15.5 MARKING: Mark the required insertion depth on the pipe with the help of suitable
marker. This depth varies with the diameter of pipe & given in the table.
15.6 HEATING: Ensure that temperature of fusion device 2700C, this is indicated by switched
off green LED. First weld can be made 2-3 minutes after green LED goes OFF. Heat the
pipe & fitting times given on the polyfusion device as per the recommended heating times
given in the table below. While heating the pipe & fitting in the matrices, apply light
pressure from both sides. For diameters over 63mm you need scraper & assembly jig for
welding.
15.7 WELDING: After specified heating time remove the pipe & fitting out of the matrices.
Heated end of the pipe should be pushed into the flared end of the hot fitting down to the
previously marked depth. Do not turn or twist the pipe or fitting while pushing in to the
matrices & pulling out of the matrices.
15.8 COOLING: After the specified cooling time, the joint gets a first stiffness, after this phase
next joint can be made. A double uniform ring of melted material around entire perimeter
of the joints confirms good quality of the weld.
15.9 Pressure test must be carried out before concealing the pipe work.
15.10 PIPES [S] WALL THICKNESS
Diameter PN 16 PN 20
Wall Internal Wall thickness Internal diameter
thickness diameter
16 2.3 11.4 2.7 10.6
20 2.8 14.4 3.4 13.2
25 3.5 18.0 4.2 16.6
32 4.5 23.0 5.4 21.2
40 5.6 28.8 6.7 26.6
50 6.9 36.2 8.4 33.2
63 8.7 45.6 10.5 42
75 10.4 54.2 12.5 50
90 12.5 65.0 15.0 60
110 15.2 79.6 18.4 73.2
16 EXCAVATION :
16.1 The width of excavation for sewers unless stated, shall be calculated by adding 250 mm. on
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 439
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
either side of the pipes. The excavation shall be carried out in such length as directed by
the EIC. No permanent work shall be begun, until the Engineer has approved the
excavation
16.2 Fencing, Lighting and Watching :
The contractor shall make proper provisions for protecting the work by providing
appropriate fencing and by providing watching and lighting (at nights) arrangements as
directed by the EIC.
The fencing posts of timber not be less than 75mm in diameter or 1.2 M above ground
surface. Two horizontal rails, sufficiently long to run from post to post and 50 to 70mm. in
dia., shall be fixed to these vertical posts, one near the top and the other 450mm. above
ground.
Proper provision shall be made for lighting at night and watchman shall be kept to see that
this is properly done. In the event of the contractor not fully complying with the provision
of these clause, the EIC. may with or without notice to the contractors, put up a fence or
improve the fence already put up or provide or improve the lighting or adopt such
measures as he may deem necessary and all the cost of such procedure as may be adopted
by the EIC. shall be borne by the contractors.
In addition to the normal lighting arrangements, the contractor shall provide, wherever a
sewer work is in progress, battery operated blinking lights (6 volts) in the beginning and
end of a trench with a view to provide suitable indication to the vehicular traffic. The
contractor shall also provide and display special boards as per directions of EIC.
16.3 SHORING :
Wherever shoring may be deemed necessary by the EIC the Contractor shall provide the
same in the best possible manner with the best material and to the satisfaction of the
EIC. The contractor shall employ such kind or kinds of shoring as the EIC may consider
the exigencies of the work to require and it is to be distinctly understood that the work
`shoring' is to comprise of such work and all appliances and appurtenances including
polling boards, sheet piling and runners (whether the joints be butt, groove and tongue
feather edge and groove, birds mouth and double splay, rebated or otherwise), together
with walling struts props, point blank shores, raking shores, blocks, wedges, iron dogs,
bolts, screws, nails and everything that may be required for due execution of the work.
Contractor's responsibility for secure shoring and or all damages :
The contractors will be held responsible for providing secure shoring and for adopting
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 440
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
every other precaution which may be necessary or proper for protecting any building which
may be damaged or be liable to damage by the excavation of any trench or otherwise by
the execution of the works in the vicinity of such building. If the EIC shall require the
adoption of any special or extra measures or precautions, the contractors shall forthwith
adopt and supply the same but this provision is not to be read or understood as in any
degree of relieving the contractors from responsibility or from liability under clause 53 of
General Condition of Contract, in respect of Claims made against the corporation by the
execution of any of the works or otherwise. After the work is completed near buildings, the
contractors shall remove any shoring and make good any cutting out or other damage that
may have been done.
16.4 Ventilation :
The contractor shall provide adequate ventilation and efficient apparatus to keep all
excavations, trenches, sewers and manholes free from all gases and he shall take
precautions to ascertain that they are in a safe condition before allowing workmen to
proceed.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 441
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
standby pumping units to be available and employed in the event of mechanical failure.
The contractor must also arrange for night and day manning and operating of the pumps
wherever necessary to ensure that at all times and whether the work may proceed.
The Contractors shall not allow any accumulation of water either from the discharge of
their dewatering pumps or their water connection on the site of their work. If an
accumulation is unavoidable, it shall be treated with insecticides to the satisfaction of the
Consultant. In case of failures to do this on the part of the Contractors, such accumulation
shall be treated by Consultants at the cost of contractors.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 442
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
specification & the drawing. However, if the contractor desires he may suggest
alternative equipments & their layout capable of meeting the requirements of final water
quality as well as the area & head room restrictions within the plant room.
17.2 Standards:
The components of all equipments shall be designed, assembled & tested in accordance
with the latest standards of the ISI. The component of all plants & equipments
shall conform to the latest relevant standards published by the ISI in order that specific
aspects under the Indian Condition are taken care of.
17.3 Inlet quality TDS 1000 ppm, Hardness 750ppm,Calcium 200ppm.
17.4 Outlet quality TDS 250ppm, Hardness 100ppm,Calcium 20ppm.
17.5 EQUIPMENT:
17.5.1 The equipments to be supplied & erected for the plant shall be constructed from first
class material with first class workmanship to the satisfaction of the architects &
consulting engineers. The equipment shall be shop assembled as far as possible, except
where the assembly is required to be done at site.
17.5.2 The Items listed below are for the general guidance of the contractor. The
contractor shall include all items essential for the complete water filtration plant & shall
revise or modify the list & submit his tender on the list which he considers suitable for
guaranteeing the Performance of the plant.
Filter vessel & pumps.
Alum & chlorine dosing tanks.
Alum & chlorine dosing pumps.
A set of external control valve should be provided on all piping for raw water inlet, water
outlet, backwash inlet & backwash outlet indicating pressure gauge for the inlet & outlet
pressure pipes with cocks & connecting piping.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 443
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 444
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5 S S SINK 1. NIRALI
2. FRANKI
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 445
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
15 SS PIPES 1. SATYAM
2. VIEGA
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 446
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
23 Insulation 1. THERMAFLEX
2. ARMAFLEX
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 447
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
28 Motor 1. Kirloskar
2. Bharat Bijlee
3. ABB
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 448
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Codes Description
BIS 15908 - Selection, Installation and Maintenance of Control and Indicating
Equipments for Fire Detection and Alarm System--Code of Practice
(2011)
IS:2189:1988 - Code of practice for selection, installation and maintenance of
Automatic Fire Detection and alarm system (second revision)
B. Mandatory Approvals
UL listing
ULC listing
FM approval
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 449
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
C. Approved Makes
Simplex (Tyco) (UL & FM Approved)
Notifier (Honeywell) (UL & FM Approved)
i. Analogue addressable microprocessor-based fire alarm system with initiating devices, notification
appliances, monitoring and control devices as indicated on the drawings and as specified herein.
ii. The system shall be capable of on-site programming to accommodate system expansion and
facilitate changes in operation.
iii. All software operations shall be stored in a non-volatile programmable memory within the fire
alarm control unit. Loss of primary and secondary power shall not erase the instructions stored in
memory.
iv. Panels shall be capable of full system operation during new site specific configuration download.
v. Remote panel site-specific software and executive firmware downloads shall be capable of being
performed over proprietary fire alarm network communications and via TCP/IP Ethernet network
communications. Ethernet access to any fire alarm panel shall be capable of providing access only
to authenticated users through a cryptographically authenticated and secure SSL tunnel.
vi. Panels shall automatically store all program changes to the panels non-volatile memory each time
a new program is downloaded. Panels shall be capable of storing the active site-specific
configuration program and no less than 9 previous revisions in reserve. A compare utility program
shall also be available to authorized users to compare any two of the saved programs. The compare
utility shall provide a deviation report highlighting the changes between the two compared
programs.
vii. Panels shall provide electronic file storage with a means to retrieve a record copy of the site-
specific software and up to 9 previous revisions. Sufficient file storage shall be provided for other
related system documentation such as record drawings, record of completion, owners manuals,
testing and maintenance records, etc.
viii. The media used to store the record copy of site-specific software and other related system
documentation shall be electrically supervised. If the media is removed a trouble shall be reported
on the fire alarm control panel.
ix. The system shall provide a means to recall alarms and trouble conditions in chronological order for
the purpose of recreating an event history. A separate alarm and trouble log shall be provided.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 450
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
i. Transmission shall be hard-wired using separate individual circuits for each zone of alarm
operation, as required or addressable signal transmission, dedicated to fire alarm service only.
ii. System connections for initiating device circuits shall be Class A.
iii. Initiating device circuits/detection loop shall be wired with 2-core, Copper Conductor, 1.5 sqmm
(16 AWG), twisted pair FRLS cable of approved makes.
iv. Notification Appliance Circuits shall wired with 2-core, Copper Conductor, 1.5 sqmm (16 AWG),
twisted pair FRLS cable of approved makes.
v. Speaker Circuit shall be wired with audio cable.
vi. The Fire Fighter Telephone line, Notification Appliance Circuit and Voice Evacuation cum Public
Address Pathway shall be wired with 2 hour fire rated shielded cable of mentioned specification &
approved make.
vii. Terminations shall be done with proper ATC lugs with insulated sleeves.
viii. Circuit faults shall be indicated by a trouble signal at the FACP. The system shall provide a
distinctive indicating audible tone and alphanumeric annunciation.
ix. Addressable Short-Circuit Isolators shall be provided at an interval of every 20 devices on a
detection loop as a general thumb rule. However, it shall be ensured that a single short circuit or
open-circuit fault on an automatic fire detector circuit/detection loop shall neither disable
protection within an area of more than 2,000m, nor on more than one floor of the building plus a
maximum of five devices (automatic detection, manual call points, sounders or a combination of
these) on the floor immediately above and five devices on the floor immediately below that floor.
x. Circuit faults shall be indicated by a trouble signal at the FACP. The system shall provide a
distinctive indicating audible tone and alphanumeric annunciation.
xi. When provided, audio notification appliance circuits shall be supervised during standby by
monitoring for DC continuity to end-of-line resistors.
F. Remote Access
i. Fire Alarm Control Panel (FACP) shall have the capability to provide a remote service access
feature using Ethernet and TCP/IP communications protocol. The Remote Access feature shall
provide automatic notification of system faults and remote diagnostics of system status for
responding technicians prior to arrival on site.
ii. The internet remote access service function shall provide automated real time off-site reporting of
discrete system events to a remote service support center with details of internal FACP fault
conditions allowing a pre-site visit analysis of repair requirements.
iii. Existing FACP controls shall be capable of retrofitting the Remote Service module as a plug-in
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 451
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
upgrade feature.
iv. The remote service network shall work on the customers Ethernet infrastructure and be Fire-Wall
friendly for two-way communications for off-site reporting. The feature shall be compatible with
existing proxy servers and firewalls shall not require any special changes or modifications.
v. The remote service system shall be a non-Windows based application to protect against
conventional virus attacks.
vi. The remote service system shall be compatible with virtual LANS (VLAN).
vii. The remote service system shall work on an outbound communication premise (panel calls home)
in order to eliminate the possibility of any inbound connection into the network (from trusted or
non-trusted sites).
viii. The remote service system shall have capability to provide an audit trail of all events and service
connections.
ix. The FAS shall be compatible to Remote Service program that provides the following requirements
if asked for:
x. 24/7 recording of FACP service activity
Off-site diagnostics by a technical specialist to provide repair and parts guidance to the service
technician prior to a site visit.
i. Network Communication
ii. Network node communication shall be through a token ring, hub, or star topology configuration, or
combination thereof.
iii. A single open, ground or short on the network communication loop shall not degrade network
communications. Token shall be passed in opposite direction to maintain communications
throughout all network nodes. At the same time the status of the communication link shall be
reported.
iv. If a group of nodes becomes isolated from the rest of the network due to multiple fault conditions,
that group shall automatically form a sub-network with all common interaction of monitoring and
control remaining intact. The network shall be notified with the exact details of the lost
communications.
v. Fiber optics communication shall be provided as an option via a fiber optics modem. Modem shall
multiplex audio signals and digital communication via full duplex transmission over a single fiber
optic cable, either single mode or multi-mode.
vi. The communication method shall be in accordance to NFPA 72 style 7.
vii. Network communication shall be Peer-to-Peer and the complete or filtered event indication shall
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 452
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
be possible in keeping with the system architecture and requirements of this document.
viii. Initiating device signals, voice signals and cause-n-effect logic shall travel in seamless and hassle-
free manner over the FDA network communication channel and even the worst condition load /
full load shall keep the response time within the limit specified by NFPA-72 / 2013 edition.
G. Required Functions
i. Operator Console/HMI: The operator console/HMI shall offer the means to display, monitor and
control all the ALARM, TROUBLE and SUPERVISORY signals from the initiating devices
connected to the FACP. The operator console/HMI shall meet the specifications mentioned for it
under Product Specification part of this document.
ii. Annunciation: Operation of ALARM, TROUBLE and SUPERVISORY initiating devices shall be
annunciated at the FACP and the Remote Annunciator indicating the type of device, the
operational state of the device (Alarm, Trouble or Supervisory) and shall display the custom label
associated with the device.
iii. Priority of Signals: Fire Alarm events shall have highest priority. Subsequent alarm events are
queued in the order received and do not affect existing alarm conditions. Priority Two, Supervisory
and Trouble events have second, third, and fourth-level priority, respectively. Signals of a higher-
level priority take precedence over signals of lower priority even though the lower-priority
condition occurred first. However, all the events shall be annunciated regardless of priority or
order received.
iv. Non interfering signals: An event on one zone does not prevent the receipt of signals from any
other zone. All zones are manually resettable from the FACP after the initiating device or devices
are restored to normal. The activation of an addressable device does not prevent the receipt of
signals from subsequent addressable device activations.
v. Alarm: A system alarm shall include:
1. Indication of alarm condition at the FACP and at the annunciators.
2. Identification of the device / zone triggering alarm at the FACP and the annunciators.
3. Operation of audible and visible notification appliances until silenced at FACP.
4. Selectively closing doors normally held open by magnetic door holders on the fire floor, floor
above and floor below.
5. Unlocking designated doors.
6. Shutting down supply and return fans serving zone where alarm is initiated.
7. Closing smoke dampers on system serving zone where alarm is initiated.
8. Initiation of smoke control sequence as defined.
9. Transmission of signal to the supervising station.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 453
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
vi. Alarm Silencing: If the "Alarm Silence" button is pressed, all audible signals shall cease operation.
The visible signals shall be off at Panel Reset.
vii. System Reset: System Reset shall do the following
10. The "System Reset" button shall be used to return the system to its normal state. Display messages
shall provide operator assurance of the sequential steps ("IN PROGRESS", "RESET
COMPLETED") as they occur. The system shall verify all circuits or devices are restored prior to
resetting the system to avoid the potential for re-alarming the system. The display message shall
indicate "ALARM PRESENT, SYSTEM RESET ABORTED."
11. Should an alarm condition continue, the system will remain in an alarmed state.
viii. Supervisory Operations: Upon activation of a supervisory device such as a fire pump power
failure, low air pressure switch, and tamper switch, the system shall operate as follows
12. Activate the system supervisory service audible signal and illuminate the LED at the control unit
and the remote annunciator.
13. Pressing the Supervisory Acknowledge Key will silence the supervisory audible signal while
maintaining the Supervisory LED "on" indicating off-normal condition.
14. Record the event in the FACP historical log.
15. Transmission of supervisory signal to the supervising station.
16. Restoring the condition shall cause the Supervisory LED to clear and restore the system to normal.
ix. Evacuation (Drill) Switch: Evacuation / Drill Switch shall be provided to operate the notification
appliances without causing other control circuits to be activated.
x. Walk Test: The system shall have the capacity of 8 programmable pass-code protected one person
testing groups, such that only a portion of the system need be disabled during testing. The
actuation of the "enable one person test" program at the control unit shall activate the "One Person
Testing" mode of the system as follows:
17. The city circuit connection and any suppression release circuits shall be bypassed for the testing
group.
18. Control relay functions associated with one of the 8 testing groups shall be bypassed.
19. The control unit shall indicate a trouble condition.
20. The alarm activation of any initiating device in the testing group shall cause the audible
notification appliances assigned only to that group to sound a code to identify the device or zone.
21. The unit shall automatically reset itself after signaling is complete.
22. Any opening of an initiating device or notification appliance circuit wiring shall cause the audible
signals to sound for 4 seconds indicating the trouble condition.
xi. Spoken Walk Test: In case the system is equipped with Integrated Voice Evacuation and Public
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 454
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Address System, the Walk Test shall have an option to notify the findings of each device through
voice notification.
xii. Install Mode: The system shall provide the capability to group all non-commissioned points and
devices into a single "Install Mode" trouble condition allowing an operator to clearly identify event
activations from commissioned points and devices in occupied areas.
23. It shall be possible to individually remove points from Install Mode as required for phased system
commissioning.
24. It shall be possible to retrieve an Install Mode report listing that includes a list of all points
assigned to the Install Mode. Panels not having an install mode shall be reprogrammed to remove
any non-commissioned points and devices.
xiii. Service Gateway: The system shall be compatible to a service gateway as described. If asked for a
Service Gateway software application shall be provided that allows an authorized service person to
remotely query panel status during testing, commissioning, and service without the need to return
to the panel using standard email / Instant Messaging Tools / Smart Phones / Tablets / I Pads etc.
Product Specification
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 455
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Supervisory, Ground Fault and shall have at least 5 programmable switch with LED for seamless
operation & maintenance.
1.1. FACP shall be UL and ULC listed and FM approved.
1.2. FACP shall comply to UL-864 9th edition.
1.3. FACP shall have a dedicated mass storage memory to store project related critical back-up like
Auto-CAD as-built drawings, reports, logs, customer-text files etc in line with NFPA-72, 2013
requirements. The memory shall be fully monitored by the FACP CPU and shall be password-
protected.
1.4. FACP shall support multiple System Power Supplies and Expansion Power Supplies in cascade to
ensure the optimum power as required by the system load and system design.
1.5. Each power supply shall provide total of 9 Amp current out of which 2 Amp per NAC shall be
dedicated to the current requirement of Notification Appliance Circuit.
1.6. FACP shall house 2 nos. of 50 AH batteries in its own housing and shall have the proper, trouble-
free charging capacity for them. However, the FACP shall be able to charge up to 110AH of
batteries if required by the system design and system load.
1.1. FACP shall have the networking capability with the other control panels of same family by adding
a network module.
1.2. FACP shall be compatible to Modbus over RS-232, Modbus over RS-485, Modbus over IP and
Bacnet over IP as different open protocol variants for 3rd party Integration. Exact variant and
module shall be considered as mentioned in commercial BOQ. The selection of exact protocol
variant shall be at sole discretion of the design consultant based on the project & system
requirement. Any deviation in this regard needs a prior formal approval of the design consultant.
1.3. FACP shall be compatible to seamless integration of aspiration system via application specific
interface module. The FACP shall be able to view, monitor and control the aspiration system from
its HMI.
1.4. FACP shall have peak value logging capability and shall be able to analyse the peak value of
individual sensors for individual sensitivity selection.
1.5. FACP shall provide min 5 or more RS-232 ports for printers and other serial port utilities.
1.6. FACP shall have IP communication capability.
1.7. FACP shall have battery brackets for seismic area protection.
1.8. FACP shall support the intelligent Cause-n-Effect programming based on the Boolean logic or
equivalent to ensure the achievement of complete system functionality as required by this
document.
1.9. FACP shall be capable of indicating different events of varying priority and shall be able to map
those events in intelligent cause-n-effect logic to achieve Positive Alarm Sequence and
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 456
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 457
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.4. Optical Smoke detector shall have manual DIP switch addressing method that does not require any
special tool from manufacturer and commissioning activity for replacing the detector in case the
detector goes faulty.
2.5. Optical Smoke Detector shall have an operating temperature range of -9C to 50C and humidity
range up to 95% RH non-condensing.
2.6. Optical Smoke Detector shall be UL & ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 458
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4.4. Heat Detector shall have selectable bases with Response Indicator, Isolator, Sounder, Relay and
CO detection capability as an option so that the best fit solution is selected depending on the
requirement.
4.5. Heat Detector shall have manual DIP switch addressing method that does not require any special
tool from manufacturer and commissioning activity for replacing the detector in case the detector
goes faulty.
4.6. Heat Detector shall have an operating temperature range of 0C to 50C and humidity range up to
95% RH non-condensing.
4.7. Heat Detector shall be UL & ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 459
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6.8. Hooter with Strobe unit shall be controlled independently on the same 2-Core NAC as per
programmed activation and deactivation criteria or from the FACP. Audible (hooter) and Visible
(strobe) outputs shall be independently configurable from FACP for its activation and deactivation
criteria as required.
6.9. In absence of any specific mention of activation and deactivation criteria, the hooter shall stop at
Alarm Acknowledge or Alarm Silence and the strobe shall stop at System Reset or Panel
Reset. This requirement shall not be deviated from unless otherwise stated cause-n-effect
configuration or unless a formal written approval is taken from the design consultant.
6.10. It shall be possible to poll each and every hooter with strobe unit from the HMI / Display /
Operator Console at FACP, isolate and include in the circuit (NAC), activate and deactivate, view
the voltage received by it from the HMI / Display / Operator Console at the FACP & Network
Repeater.
6.11. It shall be ensured that the last notification device at respective NAC receives at least 20Vdc (or 3
V above the min operating voltage) to ensure the desired performance. There shall be a provision
to verify the same either from FACP or a hand-held testing device.
6.12. Hooter with Strobe unit shall support individual performance check by a hand-held testing tool
during in Silent-Mode or Sound-Mode to facilitate performance check during normal working
hour.
6.13. Hooter cum Strobe shall have an operating temperature range of 0C to 50C and humidity range
up to 93% RH non-condensing.
6.14. Hooter with Strobe unit shall be UL and ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 460
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
7.8. If asked for, it shall be possible for FDA system to generate, print and e-mail the diagnostic report
of notification devices with tested and verified parameters.
7.9. It shall be ensured that the last notification device at respective NAC receives at least 20Vdc (or 3
V above the min operating voltage) to ensure the desired performance. There shall be a provision
to verify the same either from FACP or a hand-held testing device.
7.10. Hooter shall have an operating temperature range of 0C to 50C.
7.11. Hooter shall have humidity tolerance range up to 93% RH non-condensing.
7.12. Hooter shall be UL and ULC listed and FM approved.
8. Addressable Strobe
8.1. Strobe should be true addressable system.
8.2. Strobe shall have selectable intensity levels of 15, 30, 75 & 110 cd and shall be configured and
selected from FACP.
8.3. Strobe shall be connected to the NAC of FACP and it shall be fully monitored by FACP.
8.4. Strobe shall be controlled independently on the same 2-Core NAC as per programmed activation
and deactivation criteria or from the FACP.
8.5. It shall be possible to poll each and every strobe from the HMI / Display / Operator Console at
FACP, isolate and include in the circuit (NAC), activate and deactivate, view the voltage received
by it from the HMI / Display / Operator Console at the FACP & Network Repeater.
8.6. Strobe shall report its status with configured parameters to FACP.
8.7. Strobe unit shall support individual field testing with indication of configured and measurable
intensity level.
8.8. If asked for, it shall be possible for FDA system to generate, print and e-mail the diagnostic report
of notification devices with tested and verified parameters.
8.9. It shall be ensured that the last notification device at respective NAC receives at least 20Vdc (or 3
V above the min operating voltage) to ensure the desired performance. There shall be a provision
to verify the same either from FACP or a hand-held testing device.
8.10. Strobe shall have an operating temperature range of 0C to 50C.
8.11. Strobe shall have humidity tolerance range up to 93% RH non-condensing.
8.12. Strobe shall be UL and ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 461
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
9.2. Control Module shall provide programmable, power limited, potential-free, Form-C, SPDT Relay
to control external 3rd party utilities in case of fire alarm.
9.3. Control Module shall have the contact rating of 2A@24Vdc (resistive) and 1A@24Vdc
(inductive).
9.4. Control Module shall have an operating temperature range of 0C to 49C and humidity range up
to 93% RH non-condensing.
9.5. Control Module shall have manual DIP switch addressing method that does not require any special
tool from manufacturer and commissioning activity for replacing the control module in case it goes
faulty.
9.6. Control Module shall be UL and ULC listed and FM approved.
10.1. Monitor Module shall be addressable and shall sit on the detection loop of the FACP and shall
communicate to the FACP to report its status.
10.2. Monitor Module shall supervise potential-free, NO (Normally Open) dry contacts in order to
monitor the status of an external 3rd party device.
10.3. Monitor Module shall be configurable to report supervisory signal and alarm signal.
10.4. Monitor Module shall have an operating temperature range of 0C to 70C and humidity range up
to 93% RH non-condensing.
10.5. Monitor Module shall have manual DIP switch addressing method that does not require any
special tool from manufacturer and commissioning activity for replacing the monitor module in
case it goes faulty.
10.6. Monitor Module shall be UL and ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 462
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
11.5. Fault Isolator shall be fully monitored and addressable by FACP. It shall report its status to the
FACP and shall be controlled from FACP.
11.6. Fault Isolator shall have an operating temperature range of 0C to 49C and humidity range up to
90% RH non-condensing.
11.7. Fault Isolator shall have manual DIP switch addressing method that does not require any special
tool from manufacturer and commissioning activity for replacing the fault isolator in case it goes
faulty.
11.8. Fault Isolator shall be UL and ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 463
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
selection & annunciation, Microphone, Telephone Handset and all other necessary accessories to
complete the system requirements specified in this tender document.
1.3. Digital Voice Command Station shall operate as fully supervised multi-channel emergency voice
communication system capable automatically announce ALERT & EVACUATION pre-
recorded messages triggered via programmed Cause-n-Effect logic.
1.4. Digital Voice Command shall have a provision of manual paging in selected audio-zone / channel
overriding any ongoing ALERT or EVACUATION message.
1.5. Digital Voice Command shall have provision of cause-n-effect logic controlled message selection,
automatic announcement of the selected message in the selected zone and time-bound escalation of
the voice evacuation with priority setting for different voice messages.
1.6. Digital Voice Command Station shall annunciate TROUBLE condition of individual speaker
circuits, fire fighter telephone circuit, digital voice controllers, fire-fighter telephone controllers
and of all other controllers, modules and accessories that are connected to it for proper functioning
of the system.
1.7. Digital Voice Command Station shall have a provision of library of factory recorded voice
messages, phrases and words to facilitate the flexible configuration of voice messages for
automatic ALERT & EVACUATION announcement.
1.8. Digital Voice Command Station shall be modular in nature with regard to hardware and software
features in order to facilitate the customized system configuration and customized voice evacuation
cum manual paging.
1.9. Digital Voice Command Station shall provide Ready to Talk main microphone with zone
selection capability.
1.10. Digital Voice Command Station shall support min 5 supervised remote microphone inputs.
1.11. Digital Voice Command Station shall be capable to either house the required no. of amplifiers in
its own housing / enclosure or shall support a distributed amplifier assembly structure of
customized power capacity. It shall not limit the location and capacity of amplifier-assembly as a
system limitation.
1.12. Digital Voice Command Station shall support Spoken Walk Test which gives voice confirmation
of the status of the tested devices under walk test.
1.13. Digital Voice Command Station shall be UL & ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 464
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.2. Audio Amplifier shall provide min 2 or more freely selectable audio channels to facilitate the
announcement of min two simultaneous different messages controlled by cause-n-effect
programming.
1.3. Multiple amplifiers of stated capacity and specification shall be mounted in a single
enclosure/amplifier assembly which can either be at FACP location or away from it. The exact
power capacity of amplifier assembly shall be configured as per the commercial BOQ which will
be decided at sole discretion of the design consultant. Any deviation from commercial BOQ and
System architecture shall have a prior formal approval of the design consultant. However,
achieving the complete functionality as required in this document shall be binding on the solution
provider in terms of responsibility.
1.4. Audio amplifier shall have the necessary power supply, monitoring mechanism, over-voltage and
over-current protection, short-circuit detection & tolerance, earth fault detection and tolerance,
primary and secondary power supply failure indication and other detection, monitoring and
protection mechanism to ensure the complete, proper and trouble-free functionality as required by
this document.
1.5. Audio amplifier shall offer multiple combinations of capacity distribution between 2-channels such
as 0W & 50W, 25W & 25W, 10W & 40W or any other combination that totals to 50W.
1.6. Audio amplifier shall provide 70.7Vrms to the speaker circuit.
1.7. Audio amplifiers shall be UL & ULC listed and FM approved.
16. Speakers
1.1. Speakers shall have different variants for ceiling mount and wall mount and separate variants for
red colour and white colour.
1.2. Speakers shall have multiple tapping options of 0.25W, 0.5W, 1W and 2W which shall be field
selectable.
1.3. Speakers shall be compatible to the audio amplifier at 70.7Vrms line.
1.4. Speakers shall be capable of reliably and efficiently handling the frequency response from 400Hz
to 4000Hz.
1.5. Speaker shall be capable to generate audio message up to 89 DB at 3 m (10 ft) from it.
1.6. Speaker shall have the operating temperature range of 0C to 38C.
1.7. Speaker shall have the humidity tolerance range from 10% to 95% RH, non-condensing.
1.8. Speaker shall be UL & ULC listed and FM approved.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 465
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1. Fire Fighter Telephone Station shall be complete with Telephone Jack, Handset and required
accessories housed in a red coloured enclosure equipped with Magnetic Latch or Lock. The door of
this unit shall indicate FIRE WARDEN STATION or equivalent message prominently.
1.2. Fire Fighter Telephone station shall be capable of two-way communication with the operator at
command centre at FACP.
1.3. Operator at Command Centre shall be able to connect or disconnect to multiple simultaneous fire
fighters / callers from the field with unambiguous addressability / identification of each caller.
1.4. It shall be possible for the operator at main command centre to set up a conference call among 5 or
more fire fighters trying to speak to the operator at the main command centre.
1.5. The Fire Fighter Telephone Station / Fire Warden Station shall be UL & ULC listed and FM
approved.
PA SYSTEM
1. General Description
The contractor shall supply, install, test, connect and commission a high quality fast-acting Public
Address and Voice Alarm System complying strictly with BS 5839 part8 and EN60849 and shall be
TUV or Equivalent Agency approved. The Public Address and Voice Evacuation System shall comprise of
Audio Matrix Units, High quality speakers, Audio rack all mounted on a 19 Rack and fully connected and
integrated on the fire alarm loop. The system shall be used for Professional Sound Reproduction for all
the areas where possible special events take place.
Prior to placing order for any equipment, the contractor shall submit comprehensive document comprising
working drawings, catalogues and descriptive literature of components, acoustic calculation to meet with
BS5839 part8 RASTI (Room Acoustic Speech Transmission Index) requirements of 0.5 on the STI scale
and 0,7 on the CIS scale. The contractor shall be required to train and instruct client's personnel in the
correct use, operation and supervision of the system, preferably prior to the handing over of the project.
In order to ensure whole site integration capability, the fire and voice alarm system will be awarded to a
single specialist local supplier who will be responsible for the design, global operation, management and
interfacing of the system. The contractor shall make sure that all power tapping of the speakers must be
carried out as specified, even if the acoustic calculations indicates less power tapings. The contactor must
endure minimum of 10dB above the ambient noise levels are achieved.
The system shall be fully programmed to accommodate fire alarm and voice communication zones as
indicated on the drawings and schematics. The system shall be configured to allow on site modifications
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 466
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
with the minimum of disruption using the PC based software to facilitate future changes or alterations to
the buildings.
APPLICABLE STANDARD:
Scope of Work
The scope of work under this head shall include designing supplying and installing of Public Address
System. The work under this system shall consist of furnishing all materials, equipments and appliances
and labour necessary to install the said system, complete with Speakers, Amplifiers, Microphone, Zone
Selection Panel for interfacing with other systems.
The PA system is designed to serve the dual purpose of making general announcement and Voice
Evacuation at the time of Fire alarm activation.
System Design
The PAVA system shall be connected on the same Fire Alarm loop with in-built isolators to protect the
system in case of any cable faults. The system shall be de-centralized in nature, each distributed rack DAU
(Distributed Amplifier Unit) shall have all the DSP (Digital Signal Processing), messages, amplifiers,
monitoring in such a way that can work in a standalone mode in case the master rack is faulty or down.
The Man Machine Interface (MMI) shall be connected back to the control room, to monitor and control the
entire PAVA system. The MMI shall be fully BS5839 part 8 and EN60849 compliant and TUV approved.
The DAU shall play background / Foreground music and in case of Fire Alarm / Paging announcement, the
system shall go to full power as programmed to provide the enough SPL (Sound Pressure Level) levels to
comply with BS5839 part8, with minimum of 10dB above the noise levels.
All system components shall be digitally monitored including and not limited to, Messages, Amplifiers,
and back up amplifiers, Speaker Circuits, Audio Matrix units, Paging Microphone, Battery Charger and the
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 467
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
230VAC line. Each amplifier / line circuit shall be monitored individually and shall report any faults back
to the Master Audio Matrix Unit as well as the Paging Microphone.
The system shall be capable of sending messages automatically to any zone at any time interval, without
affecting the music in the other areas. Each Zone and circuit speaker shall have separate amplifier, system
sharing two amplifiers to multiple circuit speakers are not acceptable. There shall be one back up amplifier
for every eight amplifiers, the system shall automatically change over to the back up in case of any
amplifier failure, and the backup amplifiers shall be monitored as well. In case of any system component
failure, the paging microphone shall override any defective unit and provide paging to the required zone.
The System can provide any Cause & Effect programs after integrating with the Fire Alarm System, thus
Alert/Evacuate messages can be programmed and delayed as well as played on any zone / floor as per the
Cause & Effect approved by the Engineer.
The Battery Backup shall provide 24 hours of back up and 30 min of alarm operation. The power supply /
charger must comply with EN54 part 4 and shall be 19 rack mounted. Battery calculation must strictly
comply with BS5839 part 8 and shall be based on the amplifier size and not the speaker circuit load.
The PAVA system shall be properly integrated with the fire alarm system. The integrated PAVA system
shall cover all normally accessible areas including the car parks. All stair cases shall have dedicated zone
riser. The system shall be capable of being used for everyday background music and public announcement
duties with the fire alarm initiated emergency announcements overriding all other facilities. Initiation of
voice alarm shall take immediate priority and shall cancel all other PA operations.
In addition a FIRE DRILL, BOMB ALERT, EARTHQUAKE ALERT and an ALL CLEAR message shall
be incorporated into the operation. A fire alarm broadcast signal shall cancel any public address operation
and shall override it. When a firemans microphone is operated, this shall override any automatic voice
alarm signal being transmitted to the zone selected. The Alert and Evacuate pre-recorded messages will be
maintained in other zones while live voice fire announcements are being broadcast to selected loudspeaker
zones.
All amplifier gain shall be monitored and measured for open, short or earth faults. The Entertainment Rack
shall be located in the Control/Security Room enabling the operator to select music from the CD player,
FM tuner or the double cassette deck to transmit music to selected zones or all the zones in the building
from the touch screen paging microphone. A public address announcement shall override the music
transmission to selected zones or all zones. Paging any zone shall not interrupt music in other zones. The
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 468
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Speakers shall be distributed in the entire floor and shall be configured in different zones. The
announcement can made in zone wise or to all the speakers simultaneously in ALL CALL mode. Fire
Alarm shall be announced immediately on receipt of Fire signal from the panel to all zones or group of
Zones.
Monitoring of microphone, controller, amplifier, fireman microphone, source modular, and amplifier
changeover, AC&DC power Supply, Loudspeaker Line and Volume Control.
The Amplifier shall be used only Class-D with Digital switching power technology
System shall have facility for Backup amplifier for at least one backup amplifier over Working Amplifier.
Amplifiers
All amplifiers shall be power amplifier with High quality speech and Music broadcast. The power
amplifiers shall have adequate continuous (RMS) power output to meet the requirement of the
configuration. The unit shall be capable of delivering the rated output power with less than 0.1% harmonic
distortion in the design bandwidth. The amplifier shall have a broad band frequency response of 40 Hz to
20 KHz. The output voltage and impedance shall meet with the system requirements. Amplifiers shall be
protected against over loads and output shorts and a special thermal overload on the heat sink.
The Amplifier shall be Class D Amplifier have one channel, Two Channel, Three Channel and four
channels each channel have rated power 120/240or 500W. The Amplifier shall have switch power
technology for power electricity saving, Separate PFC design for highest reliability, separate power supply
system for each channel, Separate cooling system, sleep mode is automatically enabled when no signal
input is detected.
Amplifier shall have AC 100V or 230V power supply and DC 24V input, having separate fuse for each
channel. The Amplifier shall be connected through balanced audio input and shall work on 100V Speaker
Line.
Technical Specifications
Rated Output Voltage(RMS) 120/240/500W or 2x120/2x240/2x500
4x120/4x240/4x500W
Amplification Class-D
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 469
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Speakers
1. Speakers shall be especially designed for broadcasting high quality, integrated emergency fire
alarm signals and voice communications and approved by an appropriate authority for use in such
situations.
2. Speakers shall be ceiling, wall mounted or Horn Speaker as shown in the schedule of work and
shall be completed with mounting brackets accessories etc. Speakers shall be in metal enclosures
only.
3. Speakers shall be of high efficiency providing maximum output at minimum power across 120
14000 Hz frequency range for Indoor Speakers. Speakers shall have a line matching transformer
for direct connection to amplifiers with multiple taps.
4. Speaker external appearance shall be approved by the Architects.
5. Speakers shall be interconnected in the zone configuration.
Technical Specifications
Rated power 6W
Tapings 100V line 6/3/1.5W
Operation Voltage 100V or 70V
Effective frequency range 120 ~ 14kHz (10% Variation allowed)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 470
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Technical Specifications
Rated power 6W
Tapings 100V line 6/3/1.5W
Operation Voltage 100V or 70V
Effective frequency range 90 ~ 18kHz (10% Variation allowed)
SPL @ 1W/m >90 dB
S.P.L. ,@Full power/ 1m, dB >98 dB
Color White
Dimensions 285mm x 200mm x 85mm (10% Variation allowed)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 471
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Technical Specifications
Rated power 15 W
Tapings 100V line 15W/7.5/3.75W
Operation Voltage 100V or 70V
Effective frequency range 250 ~ 8kHz (10% Variation allowed)
SPL @ 1W/m >103 dB
S.P.L. ,@Full power/ 1m, dB >115 dB
Color White
IP Rate IP 66
Dimensions 221 x 165 x 235mm (10% Variation allowed)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 472
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
11. Red button EVAC message push to activate with priority except fireman mic.
12. 8 zone speaker outputs with separate zone volume control.
13. 8 zone separate indicator for EVAC, fault, music/paging & select.
14. System indicators of AC, DC, fault and indicators for EVAC, alert & fireman mic.
15. Zone capacity of 96 zones by cascaded 11 units router.
16. With 8 programmable control inputs and 8 programmable control outputs for voice evacuation
system.
17. With Fault, EVAC outputs and Reset input for third party system integration.
18. With fireman microphone of highest priority.
19. Priority level: fireman mic, EVAC, input 1, remote microphone, timer & BGM.
20. Two combo inputs for mic/line, 4 line inputs and one REC output.
21. Two RJ45 for cascade router, two RJ45 for remote microphone input and two RJ45 for
LAN/WAN/Internet network.
22. IP network module for optional to buy. The IP network
23. AC 230V and DC24V battery input. Auto switch into the battery backup when AC fails.
Technical Specification:
Description 8 Zone Voice Evacuation Amplifier
Rated Power Output 500W
Fireman Microphone 5Mv, 600
Line 1-2 Inputs 385mV, 10kbalanced Combo
Line 3-6 Inputs 350mV, 10k, RCA
Frequency Response 80Hz~20kHz
THD 1% at RMS,1KHz
S/N Ratio >70dB
Speaker Output 100V AB 8 zone speaker outputs
REC Output 200mV
Control Input & 8 programmable control inputs: Max 3.3V (voltage mode) or 0V closed contact
Output 8 programmable control outputs: 0V closed contact
Control output for fault & EVAC: 0V closed contact
Reset control input: 0V closed contact
Voice Message MP3 or WMA format, two separate players of SD card with protection cover,
programmable voice message up to 255, 10 years valid
Event Record HEX format, Hard Flash memory, events up to 1000 records, 10 years valid
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 473
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Software
PAVA Software with following Features: Should be connected with CAT5 Cable, Shall provide Zone
control, status monitor, Offline Program, Event Recording, System Configuration, User Management.
Software shall allow automatically playing and timing function to achieve timing programmed playing in
the designated zones for unattended operation, Built-in Automatic Timing Corrector. Support Export and
Import easily to save Data.
Technical Specifications:
Power Supply 220V/50Hz
Power Consumption 8W
1 Channel audio signal left and right channel output
CD/DVD Player
The CD/DVD player shall be capable playing MP3 audio tracks from USD or DVD or CD.
Technical Specifications:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 474
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Rack
The equipment shall be housed in a standard rack of suitable height, with Plexiglas door or metal mesh and
lock. Ventilation panels of 1U height shall be provided between each item of equipment.
Details of the proposed equipment shall be forwarded to the Consultant with performance specifications,
dimensions, construction and finish for approval.
Rack should comply with ANSI/EIA RS-310-D; DIN41491; DIN41494; IEC297-2; and GB/T3047.2-92.
The Rack should have DIN Rail Mounted Terminal Blocks for termination of Speaker Zone cables on the
rear.
All cables coming from Speaker zones, Call Stations, Power supply should enter from Bottom.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 475
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Rack should be installed at location which has minimum 600mm space from front & back for accessing it
easily.
Rack should be installed in well ventilated room preferable Air conditioned. The unit should have Fans
from top.
Dimensions
Height as per the Quantity of PA Processor & Amplifiers
Depth 600mm Deep
Width 19
Speaker Cables
All cables associated with PA system shall be of following specifications:
The 2 core speaker cable will be connected to the speakers by screw terminals before which it shall be
crimped using 1.5 sq. mm. bootlace lugs. Care has to be taken for avoiding any single strand of wire shall
not come out of Lug & screw terminals to avoid noise & leakage.
Flexible Copper Conductor of cross section 1.5 Sq. mm / 2.5 Sq. mm insulated, PVCFRLS sheathed
control Cable as per IS 694.
Approved Makes
ATEIS IDA8
BOSCH Presideo
HEINRICH DVA8/6
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 476
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 477
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IP Based CCTV system shall be provided for the entire premises for the purpose of security
surveillance, and shall be broadly divided in to
Internal surveillance for the Monitoring the Server Aisles, Entrance to Critical Spaces, and
Corridors leading to critical spaces; and also for general surveillance in the office floors.
External Surveillance for monitoring the External Periphery of the Data Centre Building
Premises, and utility areas such as the DG Area, the Fuel Unloading area, the Terrace floor with
Chiller Plant area, the Main and the Material entry Gates, rear side Material and Service Gates
etc.
1. General Specifications
The CCTV Vendor shall supply install and commission an IP Camera based CCTV system with the
objective shall be to provide High degree of Electronic surveillance system to the entire premises.
The purpose is to monitor & supervise the entire area for security purposes, as well as the record and
inform officials on unwanted, untoward incidents. It is also essential to have recorded images to be stored
at least for 90 days of all critical areas to facilitate investigations of a reported case.
The Hardware required for the System including servers, workstations, monitors, networking components,
cables, connectors, conduits, power supplies etc. shall be in vendors scope.
Development of independent LAN network for IP CCTV shall be Scope CCTV vendor.
Further, the CCTV system shall provide the direct interface with the Access Control Systems. This shall be
achieved either by offering a unified database for the IBMS, or by suitable SDK/APIs middleware
solution to enable the seamless transfer of data between disparate systems.
Should the Bidder need IT or Networking hardware more than what is provided for in the tender Bill of
quantities, then the Bidder needs to inform the tender committee / Consultants in writing on the same along
with the Tender BID and include the same in his/her bid price.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 478
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Any additions to the Takeoff Quantities given in the tender, if required by the Bidder at the tender Stage
shall need to be spelt out by the Bidder at the time of the Bid itself.
It is expected that the Bidder provides a system configuration wherein Main Directory shall be loaded on
the Main Server hardware located in the Security/ CCTV Monitoring Room at Ground Floor; and the
Failover directory shall be loaded on the failover Servers, again kept at the same location.
For the internal and external surveillance of the Data centre Premises, Strategically placed video
surveillance cameras shall provide continuous monitoring of all parts of the premises.
A. All equipment and materials used shall be standard components that are regularly manufactured
and used in the system.
B. All systems and components shall have been thoroughly tested and proven in actual use.
A minimum of 20 cameras shall be configurable with video analytics, of which, approx 7-8 shall be for
external surveillance analytics, and rest for other critical areas, reception area etc., within the premises.
Offered analytics shall have the flexibility to be deployed on any of the cameras across the complete
system as per directions from the customer/consultant during the execution/operations phase of the project
without any additional hardware/software requirement.
3. Technical Specifications:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 479
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Adjustable image size, quality and bit rate, Time stamp, text
overlay, flip & mirror, Configurable brightness, contrast,
Image Settings saturation, sharpness, white balance, exposure control, gain,
backlight compensation, privacy masks, Scheduled profile
settings, 3D Noise Reduction, Video Rotation, Defog
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 480
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
File upload via HTTP, SMTP, FTP, NAS server and SD card
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 481
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
30 fps @ 1920x1080
Maximum Frame Rate
In both compression modes
Maximum Streams 4 simultaneous streams
S/N Ratio 58dB
Dynamic Range 100dB
Video Streaming Adjustable resolution, quality and bitrate, Smart Stream
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 482
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Adjustable image size, quality and bit rate, Time stamp, text overlay, flip
& mirror, Configurable brightness, contrast, saturation, sharpness, white
Image Settings
balance, exposure control, gain, backlight compensation, privacy masks,
Scheduled profile settings, 3D Noise Reduction, Video Rotation, Defog
Event notification using digital output, HTTP, SMTP, FTP and NAS
File upload via HTTP, SMTP, FTP, NAS server and SD card
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 483
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
DC 12V
Power Input
IEEE 802.3af/at PoE Class 0
Power Consumption Max. 13 W
Safety Certifications CE, LVD, FCC Class B, VCCI, C-Tick, UL
Starting Temperature: 0C ~ 50C (32F~ 122F)
Operating Temperature
Working Temperature: -10C ~ 50C (14F~ 122F)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 484
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Adjustable image size, quality and bit rate, Time stamp, text
overlay, flip & mirror, Configurable brightness, contrast,
Image Settings saturation, sharpness, white balance, exposure control, gain,
backlight compensation, privacy masks, Scheduled profile
settings, 3D Noise Reduction, Video Rotation, Defog
Alarm Events Event notification using digital output, HTTP, SMTP, FTP
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 485
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
File upload via HTTP, SMTP, FTP, NAS server and SD card
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 486
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Adjustable image size, quality and bit rate, Time stamp, text overlay,
flip & mirror, Configurable brightness, contrast, saturation,
Image Settings sharpness, white balance, exposure control, gain, backlight
compensation, privacy masks, Scheduled profile settings, 3D Noise
Reduction, Video Rotation, Defog
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 487
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
File upload via HTTP, SMTP, FTP, NAS server and SD card
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 488
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 489
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 490
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 491
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 492
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 493
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 494
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Audio input
Audio output
Connectors DC 12V power input
Digital input*4
Digital output*2
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 495
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Safety Certifications CE / UL
5C ~ 55C ( PoE Plus)
Operating Temperature
-40C ~ 50C (AC 24V / High Power PoE)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 496
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 497
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 498
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
DVI Graphics Card to support minimum 3 multiplexed monitors, with different possibility on each of the
monitor i.e. Multiplexed, Alarm, Maps, sequence or any combination. Also support Drag-n-Drop of images
by using connected mouse device.
Embedded Gigabit network cards with fault tolerant configuration,
Redundant Power Supply, Standard video display adapter,
Minimum 3 Years Next Day Business Day on Site Warranty from OEM.
2. Applicable Standards
Original Equipment Manufacturer Standard
APPROVALS
All the cameras should be
A. CE Compliant and
B. UL Listed and
C. FCCB
EDGE SWITCHES:
i. All networking equipment shall be as minimum of 2 Layer and as a minimum shall support IGMP
Snooping Version 2 or later. It should have minimum two 1000 baseT copper ports and minimum
two slots for 1000baseT fiber modules.
ii. The IP network shall support multicasting between all ports and shall allow for Multicast streams
to be routed between netowrks.
iii. All the edge switches should be minimum Layer-2. All Layer-2 switches must finally be brought
together using 1000baseT ports to central Layer-3 switch. Connection to the servers and clients
must be 1000baseT from 10/100/1000baseT ports. Connection between Layer-2 and Layer-3
switch should use fiber backbone.
iv. Uplink port should have sufficient speed to avoid network congestion, preferably network should
not be loaded more than 70% at any stage.
v. All these Edge switches should provide IEEE 802.3af compliant PoE on all the ports
simultaneously.
CORE SWITCHES:
i. All the Main and Redundant Core switches should be minimum Layer-3.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 499
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ii. All these Edge switches should be connected to Core switches using Gigabit or 10G connectivity
depending on the load on that part of network.
iii. All the Core switches should support and be enabled with IGMP querier.
The DVM Server shall maintain a catalogue of settings for all the client, servers, and IP cameras in
the system
o The DVM shall enable the client to dynamically create connections between any camera on the
digital monitors (audio, video, serial ports and digital I/Os)
o The DVM shall provide the client seamless operation of all cameras available in the system
regardless of the actual connection to different archive servers.
The DVM shall detect signal loss and have the capability to alert the systems administrator
o The DVM Archive Server shall offer the capability to be install multiple servers software on
multiple Computer Servers to enable distributed archiving architecture on the LAN or WAN.
The DVM Archive Server, for video and audio, shall support and manage Camera connections
from IP cameras each at 25FPS PAL at custom defined resolutions.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 500
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The offered solution shall not load more than 100 cameras per server during normal functioning of
the system to ensure designed server capacity can easily accommodate all the cameras recording at
minimum resolution of 1280 x 720 @ 25FPS.
If the Bidders solution needs additional servers to fulfil this requirement, then they shall
quote for additional servers accordingly.
The DVM shall be able to set each camera frame rate, bit rate and resolution independently from
other cameras in the system, and altering these settings shall not affect the recording and display
settings of other cameras.
The DVM shall utilize multicast network communication for video monitoring.
The DVM shall offer privileged protected privacy masking feature on all the field cameras so as
only the users with specific rights can unmask the picture during live or playback. It shall also
support the password protection for such mask on exported videos.
The DVM shall not allow to login in monitoring application on multiple clients using same login
ID to avoid the misuse of the subsystem.
The DVM shall have the capability to raise the alarm in case any of the video files are being
deleted from video storage location.
Offered cameras and software should be from the same make, or should be fully integrity tested
and proven in the market place, considering the high level of complexities involved in IP system
and future maintenance and upgrade issues.
Unicast based equipment shall not be considered as an approved equal for alternate system.
The DVM shall include a federated architecture, allowing clients on the host system with the right
user rights to view video sources belonging to multiple independent video management systems
simultaneously as if they were on the same system.
The DVM shall contain recording servers used for recording video feeds and for communicating
with cameras and other devices. The recording servers shall process the recordings and playback
the video streams.
The DVM shall contain a management server that shall be the central manager of the system and
control recording servers, cameras, devices and users. The management server shall handle the
initial client login, system configuration and logging.
The DVM shall include an alarm management function that shall provide central overview, control
and scalability in any number of federated video management system installations.
It shall be possible to generate alarms based on internal system-related events, for example motion,
or archiving problems or external integrated events, for example analytics events or third-party
developed plug-in events.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 501
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Generated alarm shall appear in an alarms list in the viewing client, and it shall be possible for
operators to get an overview of, and to delegate and handle alarms from the alarm list.
The management server shall allow access to a management client from where the administrator
can configure and manage all servers, cameras and users.
The system shall allow the management server and the event server to be installed on multiple
servers within a cluster of servers ensuring that another server in the cluster automatically takes
over in case the first server fails.
The DVM shall support installation and the ability to run on virtualized Windows servers.
The DVM shall support high availability of recording servers. A failover option shall provide
standby support for recording servers with automatic synchronization to ensure maximum uptime
and minimum risk of lost data.
The DVM shall support a versatile rule system including scheduled or event-driven actions with
numerous options, including support for time profiles.
The DVM software shall include multicast and multi-streaming support.
The DVM shall include automatic camera discovery.
The DVM shall support archiving for optimizing recorded data storage through data storage
solutions that must combine performance and scalability with cost efficient long-term video
storage.
The video management system shall incorporate a fully integrated video-sharing functionality for
distributed viewing of video from any camera in the system on any computer with the viewing
client.
The DVM shall incorporate intuitive map functions allowing for multi-layered map environment.
The map functionality shall allow for the interactive control of the complete video management
system, at-a-glance overview of system integrity, and seamless drag-and-drop integration with a
video wall application option.
The DVM shall support a video wall application, which shall be flexible and hardware independent
to allow for seamless integration with the management client and viewing client.
The DVM shall support 56-bit DEA encryption and 128-, 192- and 256-bit AES encryption of
video for export purposes.
The DVM shall support full two-way audio between clients and remote devices. Two-way audio
integration shall support the following features and functions:
1. Microphone inputs to clients shall transmit audio streams to speakers attached to remote IP
devices.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 502
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. Audio from remote IP devices equipped with microphones shall be transmitted to and recorded by
the recording server. The audio shall be relayed to clients equipped with speakers.
3. Operator audio to IP devices shall be recorded by the recording server.
By default, each speaker and microphone shall be assigned to the same device that it is connected
to. The speaker and microphone shall have the capability to be assigned to other devices as well.
The DVM software shall provide fast evidence export by exporting video in various formats,
including video from multiple cameras in an encrypted native database format with an included
standalone viewing client. It shall be possible to write a digital signature to the native database
files containing recorded data. This shall allow the viewing client and the standalone viewing
client to verify that the contents of imported and opened databases have not been tampered with
and that no database files have been removed.
The DVM shall provide full awareness of the system through a system monitoring feature that
shall monitor important system components such as recording servers, failover servers and
hardware devices, and shall also include system logs and show user activity through
comprehensive audit logs.
The DVM shall include support a transactional data application designed to integrate with Point of
Sale (POS), or Automated Teller Machine (ATM) data and time-link video recordings with POS,
or ATM transactions.
The DVM shall support a solution that makes it possible to integrate multiple third-party video
content analysis applications seamlessly into viewing client environments.
The DVM shall include a Software Development Kit (SDK) that offers important capabilities for
integrating the video management system with third party software and applications.
The DVM shall include a standalone viewing client application to be included with video exported
from the viewing client application. The standalone viewing client application shall allow
recipients of the video to browse and playback the exported video without installing separate
software on their computers.
The DVM shall include support for Active Directory to allow users to be added to the system. Use
of Active Directory requires that a server running Active Directory, acting as a domain controller
is available on the network.
The DVM shall be designed to support each component on the same computer for efficiency in
smaller systems, or each component on separate computers for large system deployments.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 503
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All the vendors shall attach the point by point compliance for below specification in their technical
bid.
o Offers without the compliance shall not be considered
The product described in this specification is (IP) based Digital Video Management (DVM)
System.
The proposed solution shall not require proprietary computer, server, and network or storage
hardware.
The proposed system shall be of a manufacturer with as minimum of five (5) years of experience
and offerings in the IP network video software market, the letter stating the same should be
submitted by the manufacturer. OEM for the offered cameras & software shall have a direct
presence in India with sales and support facilities.
The DVM database and video storage shall use SQL database for their operations.
Considering this system is being deployed for Tier 3 Datacentre, offered DVM system shall
compulsorily offer below resiliency and failover functionalities. System shall have the priority
setting per camera basis with top 10% cameras nominated as Most Critical, another 10% as
Critical and rest of the cameras as Normal cameras.
o Failover Management shall be a basic feature of the DVM and should be included in offer. This
functionality shall ensure the availability of past, present and future recording with near seamless
continuity.
o The system should be capable to switching between Main to Failover Server in case of a failure of
any one of them; and from one recording server to the next recording server in case of failure of
the former in microseconds to ensure near continuous surveillance capability.
o Above failover mechanism shall be designed to achieve highest level of resiliency in the system
with optimum system components.
The DVM system shall be based on the latest in software programming technology Microsoft
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 504
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The DVM video storage shall be capable of storing video for a period of 90 days available for on
line access The Bidder shall budget for unlimited storage capability in the Tender Bid. By
Addition of Additional Storage Space, M/s AURIC should be able to expand the archival from 90
days to beyond, without any additional charges to be paid to the Bidder.
The DVM Storage solution shall be as minimum set at RAID-5 configuration
o Storage system shall be of RAID5 configured Direct Attached Storage (DAS) / Storage Area
Network (SAN) Systems / Internal storage system.
The DVM shall be based on high quality Dua / multiple H.264 stream IP cameras.
Any other image based video compression JPEG, MJPEG, MPEG4, Wavelet, or shall not be
considered as approved equal due to the high network bandwidth associated with these types of
digital video compression.
Offered cameras and software should necessarily support ONVIF interface.
Each Camera shall provide dual video streaming technology providing independent settings per
stream.
The DVM shall have a capacity to switch and control all the current cameras. DVM Software
should be expandable to unlimited cameras in future, without any additional cost to M/s
Netmagic
The system shall allow the recording, live monitoring, playback of archived video audio, and data
simultaneously
The DVM shall provide file export tool for export the native video format with all video
protections (e.g. watermark, encryption) and the ability to play this video on a standard
computer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 505
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The native file format video player shall show the status of the video authentication as available
with the original file format.
The IP Based DVM shall provide file export tool for export of single frames of video in J-PEG and
BMP file formats and for export of motion video files in AVI file format for transport and
playback on computers utilizing a Windows environment.
The Client Reserves the right to, at a later date, depending on their sourcing economies, provide
the required computers for the DVM client and servers, these computers shall be of the most
current state of the art technology available at the time of installation and as minimum shall be
better than the minimum requirements specified by DVM system manufacturer as well as tender
specifications.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 506
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 507
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The DVM Monitor application shall support digital zoom on a PTZ cameras live and recorded
video streams
The DVM client shall provide the following video analytics alarm options:
Trigger alarms or events to draw the user attention
Provide a meaningful text description of the event.
Provide OSD graphics to depict the analytics event, including the participating objects, event
location, motion directions and more.
Provide the above OSD graphics on live video, archived video and JPEG images
The Client Workstation shall have dual redundant 1 G (1000Mb) network interface and shall
operate on 100/1000 Ethernet networked and shall be of the most current technology available by a
major brand name manufacturer of computers and servers.
7. Integration Interface
DVM should provide well defined SDK/API for integration development possibilities with third
party ACS, FAS, BMS system.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 508
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Development of integration module shall be in the scope of BMS system OEM, whereas DVM
vendor should provide the requisite SDK/API for the same. Cost of the same should be included in
the offer.
The system equipment and installation shall comply with all provisions and requirements of this
specification as well as any and all applicable national, state and local codes and standards.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 509
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Power Supply Module provided should be 230V AC / 24 VDC, complete with Battery
Charger & Battery suitable for 30 minutes of operation in case of a power failure.
Loss of Power from a Particular source should raise a pop-up alarm on the Access Control GUI.
Each Networked Intelligent Controller shall utilize on-board self -diagnostic LEDs, and a
connection diagram overlay for ease of installation and service.
The controller shall also support technology feature which shall retain the last complete panel
database as a default until the update has been confirmed, ensuring the integrity of the database in
the field panel. The technology shall ensure corruptions due to hang-ups during downloads are
accommodated and the field panel always has a complete and fully functional database.
The networked controller / reader interface device shall be capable of supporting the following:
Two Wiegand interface readers with or without PIN keypads
Two Clock and Data readers
Two key pad readers.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 510
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
o The reader interface device shall have non-latching relay outputs for the following:
Two (2) door locking devices (configurable)
Two (2) auxiliary devices (door held/forced alarm, alarm shunt, communication failure, or general
purpose)
o The reader interface device shall have local processing capabilities as follows:
Alarm Shunt and Strike relay timing and latching functions
Access control decisions based on facility code (degraded mode)
Simple input/output linking on the same V100
LED / Beeper control during Card + PIN and other transactions
6. REQUEST-TO-EXIT DEVICES
Request-to-exit devices shall be provided to allow a person to exit an access controlled door. These
shall be SS Finish, and the contact capable of MTBF of 1million cycles.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 511
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
[Quantity and location of request-to-exit devices shall be as specified in contract documents and
drawings.]
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 512
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Defining custom employee groups. The feature would facilitate the logical grouping of
employees based on management structure, thus would empower the project coordinators, floor-
managers or project managers to manage access & time attendance rules and view reports of a
specific user-group.
Defining privilege level of an employee, one or more than one of the following privileges can be
assigned:
o Administrator All (privilege to manage employees, Defining access groups, Defining shift
rosters and report generation for the whole company)
o Administrator (privilege to manage employees, Defining access groups, Defining shift rosters
and report generation pertaining to a specific branch)
o Report Viewer (privilege to generate organizational time attendance and access reports)
o Normal User privilege
to generate personal time attendance reports
to put up on duty request
to request for a visitor
send messages to a specific web user
o Privilege to enquire the presence and position of an employee
o Privilege to approve on duty request
o Privilege to approve visitor request
o Group User (privilege to manage employees access groups, shift rosters and report
generation pertaining to a specific group of employees)
o Security Administrator (Privilege to configure and monitor access control hardware)
o Security Viewer (Privilege to monitor access control hardware and respond to real time
system events)
o None (No access to the system)
Advanced search form to search users on fixed and mixed search criteria such as: name,
department, title, access group, time attendance rule, card status etc.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 513
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
BAGGAGE SCANNER
1. SYSTEM DESCRIPTION The machine should be capable of scanning Laptop Bags, Tiffin carrier,
tool kits, Visitor bags and very flat objects such as envelopes.
Tunnel Dimensions Tunnel should be capable of scanning the baggage size of not less than 600
mm x 400 mm.
Penetration The Penetration shall not be less than 39 mm steel plate (typical) & 37 mm steel
plate (guaranteed)
Sensitivity The machine should be able to display a single insulated copper wire of 38 Gauge
Wire (Guaranteed) & 40 Gauge wire (Typical). The wire gauge measured in American Wire
Gauge.
Health & Safety -Machine should be International standards including the U.S.F.D.A., Center for
Devices and Radiation Health performance standards for cabinet X-Ray systems (Federal Standard
21-CFR 1020.40). Also permitted by the Federal Standard. Film safety guaranteed for high speed
films up to ISO 1600.
X-ray dose The radiation level should not exceed accepted health standard i.e., within 0.1 mR /
hr at a distance of 5 cm from external housing.
X-ray beam divergence The X-ray beam divergence should be such that the complete image of
maximum size of bag is displayed without corner cuts.
X-ray Inspection
Facility for variable contrast should be incorporated to allow enhancement of lighter and darken
portion of the image. System should have facility of variable Gamma, organic & inorganic
stripping, baggage counter.
Lead impregnated safety screens Lead impregnated safety screens should be available at either
ends of the tunnel.
Color Imaging The system supplied shall be of 6 Colors & 1 Grayscale Color Image options.
Conveyor Height The Conveyor height shall be in the range of 700-730 mm.
Conveyor belt Speed Conveyor speed shall be atleast 0.23 m/s (45 ft/min) in forward direction.
Input / output rollers system The input and output frame shall be provided with rollers of
length in multiples of 500 mm on each side with barrier frame to prevent bags falling off.
Conveyor Load 165 Kg distributed load (364 lbs)
Operating Temperature & Humidity The operating temperature should be 0C to 50 C
Humidity - Up to 95% non-condensing
Power Requirements & Power Conditioning
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 514
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 515
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 516
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Bidder to meet the following Minimum Specifications for the Door Frame Metal Detector:
2. GENERAL
This product shall be manufactured by a firm whose quality system is in compliance with The ISO
9001/2000 Quality system.
Bidder is required to submit technical datasheets of all products and installation manuals of all
Products, technical bids without these documents shall be considered incomplete and shall be
rejected.
3. Technical details:
Principal of Operation:
o Microprocessor Based Operation, Digitally Controlled, voltage very low frequency.
Dimensions:
o Net Passage clearance is 0.76 cm wide & 2.0 m high.
Frame:
o Rugged structure, not susceptible to false alarms due to mechanical Vibration. ABS Side
panels should have ribbed design for additional support to structure and should be detachable
for ease to install & transport.
Power :
o Operatable on both A/C main supply and battery supply
o Operating voltage: Mains 230 V + 10% 50 Hz.
o Battery operated from and provided with 12V SMF battery of suitable capacity to give 4 hours
of operation.
o AC connecting socket near the top of the side panel, for AC supply connection so that power
frequency does not affect the detection capability of DFMD in long run.
Zones:
o Should have minimum 9 overlapping detector zones in DFMD.
Search Coil:
o Multi-loop search coils housed in two side panels only.
Control:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 517
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
o Control panel should be built inside the frame on the top with all the operating controls built
in. It should have plug -in card system for easy maintenance
Control Unit Display Panel:
o The DFMD Panel should have digitally controlled membrane touch button pads for selection
& programming of the system
LCD:
o Should have 4 lines Backlight LCD, which should display the security level settings, traffic,
counters etc.
Metal Locator Display:
o There should be Alarm LEDs on Control panel on a symbolic body showing the alarming
zone. This would display whether the point of detection is in the right / left / centre of the body
at the corresponding height level.
Metal Intensity Level Indicator:
o There should LEDs on the display panel for graphical indication of the detection level of
metal. The size of threat level shall be indicated by the colour of the LEDs. More threat shall
make the RED LEDs glow. This display should operate only when the Infra Red beam is
broken when a person passes through the detector.
Battery indicator:
o The control panel should also have battery indicator.
Traffic Light status indictor:
o An LED indicating Green / Red status of the traffic light should be installed on the:
o Control unit display panel
o Top and bottom of both side Panels on the exit side of the metal detector
o Sensitivity level- should have atleast 8 security level and further provision for adjustments to a
fine step.
o While in operation the LCD should always display the IN and OUT counters separately, along
with security level.
Detection
o Capable to detect all Metals, Zinc & Metal Alloys using single detection Program. Should be
able to detect ferrous / non-ferrous metals at any location.
o Shall be tested to IS: 14132: 1992
o Shall have Continuous active detection capability, also quick reset capablity after each
detection.
o Should allow minimum 30 people per minute to pass through MZDFMDU
o Should have uniform sensitivity throughout the door frame.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 518
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
o Should have Error Free reliable operation for various object speeds ( slow walk speed)
o Should have Minimum Nine zones, all overlapping zones: Left Top, Center Top, Right Top,
Left Middle, Center middle , Right middle, Left bottom, center bottom, right bottom.
o The unit should have Intelligent 5 digit traffic Counter display on LCD.
o The unit should show separately IN and OUT counter. The counters should have provision for
selection of visible / invisible mode.
Sensitivity
o The unit shall provide for Individual zone sensitivity settings for all 9 overlapping zones.
o The unit shall provide for Overall zone sensitivity adjustment.
o The unit shall be capable of 20 different adjustable sensitivity levels.
o The Magnetic field of the DFMD Equipment should be harmless to magnetic media,
electronics device supported by Test certificate from NABL(India) or other accredited labs
from the country of origin of equipment, wearers of heart pacemakers and pregnant women (by
recognized medical institute).
o Bidder should provide the certificate for the same along with bid.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 519
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
BOOM BARRIER
GENERAL SPECIFICATIONS:
Vehicle Barrier shall mean an Electro-mechanical barrier system comprising of a Main Housing & a
Boom Arm that serves as a blocking device.
o The Main housing cabinet shall house the Motor, Controller, the electrical wiring etc., for the up and down
movement of the blocking arm. The cabinet shall be IP44 rated and as an option if site conditions demand,
be offered in 304 grade Stainless Steel.
The Barrier shall operate with a DC motor & shall not adopt or involve a hydraulic device for the said
operation. The Hydraulic device is not preferred in order to establish a trouble-free long life for the barrier
as only a motor driven barrier is maintenance free not requiring oil replenishment, maintenance of oil seals
etc.
The DC Motor shall not be of more than 100 watts for a barrier with 4 meter boom length & not more
than 200 Watts for a barrier with 6meter boom length so as to consume less power. The Drive shall have
an ABS Electromagnetic Braking system so as to offer smooth lifting and lowering of the arm without any
jerks during the operation or at the end position.
The Cabinet Housing: Shall be fabricated from a 2mm thick sheet metal & powder coated in orange
colour. The cabinet dimension shall be of a height of around 1000mm & a square or almost square
dimension of around 300mm. The Barrier arm shall be at a height of around 900mm to the middle of the
arm from the ground.
The Barrier Boom Arm: known also as the blocking arm shall be an aluminium extrusion of dimension
of approximately 90mm high, 30mm wide and of the desired length. The Boom arm shall be powder
coated in white with red reflective tapes for easy, clear and good visibility at night against shining lights.
The Micro PC Programmable Logic Controller shall offer Auto/Manual or Mixed function
o Signal input for barrier open/closed position
o Vehicle detection input while arm is closing
o Automatic barrier closing can be set within 0-14 seconds interval & Compulsory barrier closing can be
set within 15 seconds
o Counter and memory function when barrier keeps opening and closing. The function allows barrier
closed with automatic counting for safety reason.
o Controller is able to monitor moves of machines and alert automatically in case of any unusual
situation, such as collision.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 520
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Barrier Boom Swing-Away Function As an option Boom with Swing Away Device may be requested.
The Swing Away Flange shall be offered with Boom Release Switch that could in-turn trigger other
devises to initiate appropriate action. This typically could be used to deploy Bollard or Road Blocker or
even trigger a Video Camera or an annunciator when a vehicle hits the boom and dislodges the boom from
its position. This way in all probability the boom may also not be damaged.
Barrier Opening & Closing Speed for up to 3.5meter long arm shall be adjustable to 1.5, 2.5, 3.5
seconds with a single action stroke & that for a 6 Meter Boom Arm 4 Secs. The Barrier shall be
capable of being operated manually in the event of power failure or any other abnormality. The Barrier
arm shall be able to be folded in case of a basement installation or where there is a height restriction.
The system shall offer the flexibility of 60, 70, 80 &, 90 open. As a standard, 85 barrier arm open
for folding arms may be offered.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 521
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 522
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 523
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 524
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 525
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Intent of Using a Platform is to ensure that the same remains 100% Agnostic to any Brand of
Hardware and also is capable of Seamlessly Integrating with any type of Application Software.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 526
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 527
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 528
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
10. Totalization
11. Demand Limiting
12. Scheduler Module
13. Logic generation and Control Modules
14. Diagnostics
15. Database management
The IBMS Platform Must have exhaustive and detailed scheduling functions inbuilt into the system.
The IBMS Platform Must have all Control Loop Objects like but not Limited to - PID Loops, Analogue
IO, Binary IO, Comparison Objects, Mathematical Function Objects, Interlock Objects, Custom
Programming Objects, Composite Object etc to enable a Free Programming Interface.
The IBMS Platform Must also Integrate with Third Party Advanced Graphic Engines using Open
Interfaces.
The IBMS Platform Must be based on HTML5 only to display High Level of Graphical and reporting
capabilities.
The IBMS Platform must include a freely configurable Data Trending functionality based on customer
requirements including but not limited to single shot, roll-over, split, compare, benchmark etc.
The IBMS Platform must include exhaustive reporting and the flexibility of providing Custom Reports
either by integrating to external applications or indigenously.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 529
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 530
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Acknowledgement of alarms shall be automatically printed and will indicate the time, date, and
any message generated by the operator.
Alarm silencing shall be by the authorized operators by pressing the silence key.
Alarm Clear: When alarms are cleared, then a message shall be produced to indicate the
description of the alarm point, its current state, and the time and date.
Alarm Review: Points in alarm shall be displayed on the operators panel using the alarm review
function.
10. Reports
1. Standard reports shall be provided, which shall be operator selectable to appear on the operator
station, any selected printer or both. A terminate report command shall be available to allow the
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 531
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
operator to stop any report in the process of being printed. Standard pre-formatted reports to be
provided shall include:
i. Point summary reports may be requested at any penetration level. Point summary reports
shall include the current value/status and condition, point descriptors and all relevant
information. Point summary reports shall be selectable for all points.
ii. All reports shall be capable of being scheduled to run at a specific time and/or interval via an
operator function supported by necessary data entry templates and interactive prompts.
2. As a minimum, the system shall provide the following summaries:
i. Point summary
ii. Alarm summary
iii. Limits summary
iv. Lockout summary
v. Off-line summary
vi. Override summary
vii. Utility summary
viii. Point status (alarm, locked out, off-line, override)
ix. Point name
x. Point status/value (automatically updating)
3. The alarm summary shall list all points in alarm in the selected system. It shall be possible to print
on a single summary, all points in alarm in the building. As a minimum, the alarm summary shall
include:
i. Point name
ii. Point status/value (when alarm occurred)
iii. Alarm message
iv. Date and time of alarm occurrence
v. The limits summary shall list all the alarm limits, and warning limits.
4. The lockout summary shall display points in the selected systems which have either reporting or
triggering locked out.
5. The off-line summary shall display points in the selected systems which have lost communication
with the system.
6. The override summary shall display points in the selected systems which have been overridden by
operator command.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 532
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
7. The utility profile shall display the total consumption, measured peak for the current period and the
previous period.
8. Trend reports shall allow the operator to randomly select logical group of points to be recorded at
selectable time intervals. It shall be possible to assign up to ten variables to each trend report. The
format, headers, footers, and calculations shall be selectable by the operator. The trend report
shall be stored to disk and shall be subsequently capable of being displayed, and/or printed by the
operator.
7. Dynamic trends shall provide up to eight points and show real time activity of the associated
points. This information shall be printed and/or displayed in numeric, bar chart, curve plot, pie
chart, etc., as selected by the operator. Graphic plots shall allow a unique color for each point.
Sample interval of points selected for dynamic trend shall be user selectable. 3-Dimensional
dynamic trending must be provided in the system.
8. Alarm and run time reports shall be automatically issued to assigned printers immediately upon
occurrence, and shall consist of the point with engineering unit, the time, and the date, and the
alarm message.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 533
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
the sample interval, and time at which the report is printed. Trend output format shall be as
specified for trend logs (shaded, un-shaded etc).
12. Utilities
1. The Central Station personal computer (P.C.) shall be provided with the following menu selected
graphic system utilities or desktop application packages.
2. The system provided must be capable of running standard software packages concurrently with
the real time system. System should be capable of supporting third party software packages like
spreadsheet, word processing etc.
3. The base system software shall include a windowing feature to allow the operator to monitor
the real time system and use the third party software simultaneously.
4. All third party software packages identified shall have access to the system historical data base.
There shall be real time clock facility to help in time scheduling. The scheduling feature shall not be
dependent on a central database or an operator workstation.
The following commands shall be able to be time scheduled to be issued at a later day and time
from the operator workstation or portable workstation:
i. Start and stop a point
ii. Adjust analog value
iii. Change set point
The following commands shall be able to be time scheduled to be issued at a later day and time
from the operator workstation:
i. Change alarm limits or warning
ii. Lock/unlock point reporting or point control
iii. Demand limit target setting
iv. Load rolling target setting
v. Reset tracking period for energy statistics
vi. Trend point enable/ disable for a point
vii. Totalization enable/ disable for a point
viii. Reset totalization value
The following summaries shall be able to time scheduled to be printed or stored in a disk file at a
later day and time from the operator workstation:
I. Standard point summary
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 534
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Commands shall be able to be issued repeatedly on specified days of the week at specified times.
A system wide calendar shall be set up to define each day as:
i. Regular day
ii. Special day
iii. Holiday
The system wide calendar shall be stored in multiple locations so that the failure of any one device
does not cause the system to fail.
The calendar shall automatically accommodate the leap year and the turn of the century.
The calendar shall allow the days to be scheduled one year in advance from the current system date.
Separate schedules shall be stored for:
i. Regular days
ii. Special days
iii. Holidays
The system shall accept one-time schedules to accommodate overtime usage.
One-time schedules shall be automatically deleted from the system after execution.
The system shall allow one-time schedules to be programmed up to one year in advance.
After recovery from a power failure, the system shall determine any time scheduled commands which
should have been issued during the period that the power was off. These commands shall automatically be
issued.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 535
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. For every digital point in the system, a point history of the last 10 change of states shall be
maintained. The operator shall choose whether point history previous to the last 10 change of
states shall be discarded or archived.
3. The most recent 10 samples of digital point history shall be able to be displayed at the Control
Station.
4. Point history samples with time/date shall also be taken under the following conditions:
i. Point in alarm/return to normal
ii. Point overridden/released by operator
iii. Point on-line/off-line
iv. Point reliable/unreliable
6. A report shall be available showing all points for which point history is being archived.
7. The system shall provide point history graphs for analog/digital points.
Point Trends
8. The trend feature shall be able to record any of the following parameters for any point :
i. Point value
ii. Point alarm status
iii. Controlling feature
iv. Operator override flag
v. On-line/Off-line flag
9. The operator shall be able to select points and define any interval on which samples may be
taken.
10. For long term storage of samples, trend data shall automatically be updated.
11. A report shall be available listing all points being trended. The report shall display:
i. Trend status
ii. Point name
iii. Parameter being trended
iv. Display units
v. Sample interval
vi. Number of samples taken.
12. A trend for a point shall be able to be started either by operator command or according to a time
scheduled command. A trend for a point will end as a result of an operator command, time
scheduled command or when the required number of samples has been collected.
13. Trend samples shall be displayed in either tabular or graphical format. A minimum of eight
trended points shall be able to be displayed concurrently on a graph or report.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 536
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
14. The trend graph display shall automatically scale the value and time axis to display all samples.
From the trend graph, the operator shall be able to select and read the instantaneous value of any
previous sample.
15. The trend point graphing capability shall be a built-in feature of the system and shall not require
operator set- up. Systems which require trend point data to be exported to third party software
shall not be acceptable.
16. Totalization
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 537
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
8. The operator shall be able to define a demand target that is not to be exceeded and the demand
limiting feature shall analyze trends and electrical demand and turn off equipment when a
demand peak is anticipated.
9. The demand limiting and load rolling features shall be fully integrated with all other features so
that the following safety parameters are maintained:
10. Minimum on time
11. Minimum off time
12. Maximum off time
13. Maximum number of cycles per hour
14. At the end of the minimum off time, a comfort parameter, such as a temperature, shall be
sampled. If the comfort parameter is in alarm, the point being controlled shall be turned on.
15. The following statistical data shall be maintained:
16. Date / time of start of current period
17. Total consumption for current and previous period
18. Actual peak demand with time/ date for current and previous period.
19. Instantaneous demand
20. Interval demand
21. Total shed loads
22. To provide the operator with an opportunity to manually shed loads that are not available to
demand limiting or load rolling, the operator shall be notified when the demand limiting or load
rolling run out of loads to shed.
23. To advise the operator when the performance is outside of expectations, the operator shall be
notified when the demand peak target or load rolling target is exceeded.
The software should be Minimum Capable of Providing Aggregate Demand Summary - This report
aggregates (totalizes) multiple points (meters) and shows the peak, minimum, average, and total
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 538
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
consumption as well as computes load factor. By reducing peak consumption and levelling the total load,
volatility is reduced and energy customers can make significant improvements in their energy
procurement.
1. Summary Ranking Reports - By selecting this report, the user can identify the 10 worst or 10 best
sites in the database. Once the report type has been selected, parameters to define before the
report can be generated will include the following:
a. Measurement unit KW, therms, CCF gallons, PSI, etc. The database will search for all
values matching the request.
b. Compare an entire facility or normalize by square foot
c. Time periods to compare
d. Highest values or lowest values Will be able to view either the best or worst 10 points
matching the defined parameters
e. Cost or consumption in future revisions
2. Spectrum Summary Report A quick view of any point or aggregated point with color coding
identifying the reasonableness of the data value. The chart can report on up to one year of data,
with the ability to zoom to a higher definition. As data values approach and/or exceed historical
ranges, the color on the graph will change to identify such. If all data values are within historical
ranges, the user can move on to other functions. In the following screen shot, the Spectrum
Summary Report is reporting on total electricity for an aggregated point, which consists of 6
schools. The reporting period is six weeks, with the blue identifying low loads overnight and on
weekends. The fourth weekend in the report was a three day weekend which is identified by a
larger blue gap. A user can also see rising consumption (red) as temperatures rise going into the
summer season. When the user clicks on an area of the graph, the data value along with time
stamp will appear. The colors and associated data value ranges are user definable. The following
screen shot is an example of the Spectrum Summary Report.
3. Equipment Operation Reports - Users will have the ability to analyze digital points and identify
run times. Comparisons between sites or points can be made and run times can be graphed. For
example, comparing lighting or HVAC run hours in a group of stores or comparing HVAC run
hours in June for Store 1 versus Store 2. Data will be displayed in time and percentage.
4. Relative Contribution Report This pie chart report will give users the ability to identify how
individual points contribute to a total from a point group. The user would select a group of
points, calculate the aggregate consumption of the group, and report on the individual
contribution of each. Data will be displayed both graphically in a pie chart as well as in tabular
format. Users could identify that HVAC is 48% of the building load; lighting is 42%, or Building
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 539
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1 accounts for 14% of the total enterprise load and Building 2 contributes 19%. This report will
allow users to identify inefficiencies and help perform budgeting.
5. Average Profile The report will allow the user to average the load for a single load across time
periods and give the average load, and/or aggregate multiple meters (loads) and view the average
aggregated load. This report will be very beneficial when negotiating with energy service
providers because it includes the load profile and consumption totals. With the ability to filter by
time periods, measurement units, points or point groups, weekdays, and weekends, load profiles
with associated data will allow the user to procure exactly the amount of energy required. This
reduces risk for the energy provider and therefore reduces cost for the end-user.
The user will be able to manipulate between 1-minute intervals and hourly intervals. In addition,
users will be able to choose between auto scale and manual scale. For example, if the
minimum value is 100KW and the maximum is 500 kW, the user can have the chart automatically
scale between those values or they can select any range to scale the 400kW range. When printing
charts, this may be useful. This will be useful for sophisticated users who need a higher resolution
of data. The following screen shot is an example of the Average Profile Report.
6. Point Trending This report will allow the user to choose a single or multiple points and trend
the values over a specified time period. Either analog or digital points can be trended and multiple
variables can be selected to be report. For a visual representation of several point values, the user
will view all points on the left Y-axis. If the user would like to perform a statistical analysis
identifying correlation coefficient and standard deviation between variables, they will have the
ability to select a single point for each Y-axis. If a point group has been created, it would be
presented as a single point value. The same auto scale/manual scale feature discussed in Average
Profile Report is available in Point Trending. The following screen shot is an example of the
Point Trending Report.
7. Universal Comparison Report This report will convert electricity, gas, and other fuels to KBtu,
a common measurement unit. Once the consumption values are converted to a common unit,
users will have the ability to compare efficiency or analyze the total energy breakdown for a site
or group of facilities. Once this report is selected, the user will define parameters such as sites or
points to compare, time period, type of graph, and percentage versus measurement unit. Gas,
propane, oil, electricity and other fuels can be converted to KBtu.
8. Exception Report This report will identify all data values for the specified period that does not
fall in a user-defined range. Although the range will be user definable, the benchmark or baseline
to be compared against will be historical data. Users can get to this report by selecting it among
the library of nine report templates, or can automatically be taken here from the Average Profile
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 540
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Report or Point Trending Report by clicking on an Exception button once a profile is being
viewed.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 541
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. Each DDC shall operate as a standalone controller capable of performing its specified control
responsibilities independently of other controllers in the network. Each DDC shall be a
microprocessor-Based, WEB BASED, multi-tasking, real-time digital control processor. EACH
DDC CONTROLLER WILL BE MAX 30 POINT CONTROLLER. DDC Shall be 100%
open using Either Modbus, Bacnet or Lonworks Only as a Protocol.
2. Totalizer points would support Math resolution of 15 digits, or 999,999,999,999,999
3. On board RTC
4. Optimization for Heating and Cooling
5. The controllers shall consist of single 32 bit microprocessors IP for reliable throughput, based
with EEPROM based operating system (O.S.). Multi microprocessor to meet 32 bit, such as 2
Nos. of 16 bit or 4 nos. of 8 bit, criteria is not acceptable. It should operate on should operate at
55 MHz and is supported with 2 MB of Flash memory and 8 MB of RAM.
6. Communication: The controllers should have on board Ethernet Port.The Ethernet Protocol
is the One to be Used in the AURIC Project well as the RS485 Protocol is kept as a Feature
in case of emergency. Supports Ethernet 10Base-T/ 100Base-T interface,
7. Device ID: Complementing existing standard protocols, the DDC shall be uniquely identifiable
over the network. This facilitating online network device search and simplify reconfiguration
8. High Accuracy Analog Channels: shall be capable of 12-bits A/D converter and 12- bits D/A
convertors
9. Shall be a standalone programmable device
10. Online Firmware Upgrade/Configuration: Shall support firmware upgrades either through RS485
or Ethernet connection.
11. The controller shall have a built-in High accuracy Real Time Clock lithium Battery Life Span: 5
years
12. Network Security: All configurations changes shall be protected via password setting, either
through standard network protocol access or web browser
13. The DDC Controller shall be provided with LEDs for continuous status indication of power,
communication bus, watches Dog, Networking OK, and self-diagnostics as a minimum.
14. All DDC controllers shall be DIN channel mountable and installed in suitable enclosures. The
enclosures shall be provided with hinged doors with locking facility. Apart from the controllers,
the enclosure shall house the terminal blocks, load relays and associated equipment. The internal
wiring in the enclosure shall be factory wired. The packaging shall be such that complete
installation of the field equipment and field wiring can be done prior to the installation of the
electronics.
15. Agency Listing: CE, UL 916, C-Tick
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 542
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
16. Shall support the expansion from 24 to 96 or more IO points through expansion cards with
following Input/output Configuration:
1. Universal Input:
Voltage: 0 - 10V (+/-0.005V), 0 - 5V (+/- 0.003V)
Current: 4 - 20mA (+/-0.01mA), 0 - 20mA (+/-0.01mA)
Resistance: 0 - 30K (+/-10 Ohm), 0 - 10K (+/-5 Ohm), 0 - 1.5K (+/-1 Ohm)
Thermistor: 10K, 10K Shunt, 1K Balco, 1K Platinum
2. Digital Input:
Type: Voltage Free
Limit: +5V at 500Ohm Resistance maximum
3. Digital Output:
Type: Relay Contacts, SPST NO, 48VA at 24VAC,
4. Transistor Output:
Type: Open Collector Output, Isolation 3.75KV- Max Rating: 1A, 60V
5. Analogue Output
12 bits resolution - Type: Current: 0 - 20mA, 4 - 20mA (up to 800 Ohm load), Voltage: 0 - 10V
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 543
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
the medium being measured and shall have sufficient physical strength to withstand pressures and
velocities to which they are subjected. Wells shall be installed in the piping at elbows where
piping is smaller than the length of the well to effect proper flow across the entire area of the
well.
Thermowells
When thermowells are required, the sensor and well shall be supplied as a complete assembly
including well head and greenfield fitting.
It shall be pressure rated and constructed in accordance with the system working pressure.
Thermowells and sensors shall be mounted in a threadolet or 1/2" NPT saddle and allow easy
access to the sensor for repair or replacement. Thermowells shall be constructed of the following
materials:
Chilled and Hot Water; brass.
Steam; 316 stainless steel.
Brine (salt solutions): marine grade stainless steel.
1. Temperature Sensors
Sensors and transmitters shall be UL / CE listed, provided, as outlined in the input/output summary and
sequence of operations.
The temperature sensor shall be of the resistance type, and shall be either two-wire 100 ohm platinum
RTD, or two-wire 1000 ohm platinum RTD.
The following point types (and the accuracy of each) are required, and their associated accuracy values
include errors associated with the sensor, lead wire, and A to D conversion:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 544
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Ambient temperature rating of -30 to +80 deg. C, protection class IP65 and Pt 1000 sensing element with
SS316 stem.
Immersion sensors shall be provided with a separable stainless steel well with NPT (M) connection
and length shall be 6. Pressure rating of well is to be consistent with the system pressure in which it is to
be installed.
Thermowell should be single piece Barstock Construction
Operating range shall be -20 to 80 deg C; pressure rating shall be min. PN 16, IP 65 protection, 1000
ohms platinum at 0 deg. C. Accuracy to 0.2C at 0C, DIN Class A
D. Temperature Transmitters:
2. Humidity Sensors:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 545
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Duct and room sensors shall be UL / CE listed have a sensing range of 0% to 100% (at 25 Deg.C) with
accuracy of 2% R.H and 0.5 Deg.C. Humidity Sensor Element should be All-Polymer sensing element
and NTC for Temperature. The RH sensors should incorporat the True RH technology. With fire retardant
enclosure.
Duct sensors shall be provided with a protection cap with Stainless Steel sintered mesh. Duct probe
material should be stainless steel.
Outdoor air humidity sensors shall have a sensing range of 0% to 100% R.H. It shall be suitable for
ambient conditions of -40C to 85C with IP66 protection class.
Humidity sensor's drift shall not exceed 0.5% of full scale per year.
It should be programmable with MMI Protocol.
3. Pressure Sensors
A. Differential Pressure Transmitters for air:
1. Transmitter should be UL / CE listed and have a removable LCD display with multiple units. The
response time, units and range should be site adjustable through DIP switch to counter adjust
fluctuating readings.
2. Air pressure sensor shall have Silicone diaphragm construction. Sensing elements shall withstand
continuous operating conditions of 1000 Pa and static pressure of 10000 Pa. Sensor shall be
complete with 4-20 mA and output, with over voltage protection. The accuracy shall be 0.5% or
better. The total error band shall be 1% or better.
3. Sensor shall be complete with 4-20 mA and 0 -10 V output simultaneously, with over voltage
protection. Transmitter should be available with optional MODBUS output.
Sensor shall have linear output signal. Zero and span shall be field-adjustable with 5 Point onsite
custom calibration.
4. Standard of acceptance: Omicron series M11 or approved equal.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 546
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. Sensors shall be UL / CE listed. Flow meter shall be a single electro-magnetic type inline flow
meter able to work in conductivities above 5S.
2. The wetted material shall be constructed of stainless steel with PTFE Lining and electrode
material shall be Titanium with Die cast aluminium IP67 Enclosure and LCD Display. Display
should indicate Instantaneous,Totalized flow and multiple units.
3. Range shall be field settable.
4. Flow meter accuracy shall not exceed +/- 0.5% with velocities from 3 to 30 fps.
Provide output via 4 20mA Signal and MODBUS.
7. Level Switch:
1. Level Switches shall be UL / CE listed and have SPDT Contacts. The switch shall be Float
operated, with top mounting.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 547
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. Switch shall have SS316L wetted parts, proof pressure of 10 bar and burst pressure of 20 bar
Minimum. The accuracy shall be 0.25% or better. The total error band shall be 0.5% or better
3. The switch shall have IP68 protection, with corrosion resistant cable. The current rating for the
switch shall be 15A, 230VAC. Fire retardant ABS enclosure.
Hardware Requirements:
1. IBMS Data Management Station: Client workstation with Intel i5 processor with minimum
320Gb HDD, 4 GB RAM, 19" TFT Monitor, DVD Writer, two serial(one for mouse and one for
Serial data acquisition RS converter) and one parallel port (for Printer), multimedia
speakers,infrared mouse;
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 548
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. 00 DPI colour Laser jet A4 printer for printing reports complete with communication cable,
power cable, printer driver software etc.
General Requirements.
The POT / DDUs shall permit the project operating staff to:
Display point values
Display parameters
Change time schedule elements
List and acknowledge alarms
Monitor points in the system
Command points (manual overrides) of points
Override input points (put inputs in test)
Read and check LonWorks variables on the network
Password protected
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 549
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
9 Workstation HW HP/Dell/Lenovo
10 Printers Samsung/HP
Caliplast/ Technoflex/RR Kabel/ Polycab/
11 Cabling
Supercab
Siemens/ JCI/ Honeywell/ Sontay /
12 Duct Mount Temp Sensor
Dwyer/Omicron
Siemens/ JCI/ Honeywell/ Sontay /
13 Duct Mount RH Sensor
Dwyer/Omicron
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 550
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
IGBC 2011 for India Core and Shell Projects (based on IGBC 2009).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 551
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Plant capacity
Package Sewage Treatment Plant (PSTP): - 105 KLD capacity [average flow ].
A PSTP of 105 KLD capacity [average flow] is planned which will cater the sewage generated.
Table 13: Influent Characteristics (Reference CPHEEO Manual for Sewerage and sewage treatment
system)
SI. No. Parameter Values
1 pH 6.5 - 8.5
2 BOD5 @ 20C, mg/L 250 300
3 COD 400 500
4 To 300 - 400
5 Oil and grease, mg/L 10 - 20
6 Total kjeldahl Nitrogen (as N), mg/L 40 - 50
7 Total Phosphorus, mg/L 5-7
8 Faecal Coliforms MPN/100 ml 6 8
10 to 10
It is proposed that the sewage which is generated is to be treated to such standards that it can be used
for gardening, toilet flushing and washing of internal roads & paved areas.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 552
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
From the point of view of better environment, it is contemplated that the entire sewage will be treated
to 5 mg/l (BOD and TSS) standards. The EPA standards for reuse of municipal sewage are given in
Table 14.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 553
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 554
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The following standards and codes and statutory requirements to be followed for design and
implementation of the Solid Waste Management:
Table 16
Codes / Manuals Description
CPHEEO Manual on Municipal Solid Waste Management, Ministry of Urban
Development, Government of India, 2000.
Guidelines by Supreme Solid waste management in class-I cities in India
Court of India, 1999.
[20/7/1998], S.O.630 Bio-medical waste (management and handling) rules
(E), 1998.
S.O. 2400(E), 1999. Recycled plastic (manufacture and usage) rules
[25.9.2000], S.O. Municipal waste (Management and Handling Rules),
908(E), 2000 and the
amendment 2013.
Batteries (Management and handling) Rules, 2001.
1999, S. O.705 (E), Amendment to the Recycled Plastic Manufacturing and Usage
2003. Rules,
[17.9.2003], S.O.1069 Bio-Medical Waste (Management and Handling)
(E), 2003. (Amendment) Rules,
Hazardous waste management and handling rule, 1989.
S.O.2265 (E), 2008 Hazardous Wastes (Management, Handling and Trans
boundary Movements) Rules,.
S.O. 2400(E), 2009. Plastics (Manufacture, Usage and Waste Management) Rules,
[17.09.2009],
E waste (Management and handling) Rules, 2011.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 555
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.3 All materials and works for operations and maintenance of Potable water supply
rising mains and distribution networks, Elevated Service Reservoirs (ESR), Recycled
water supply rising mains and distribution networks including valves, flow meters etc.
shall confirm to CPHEEO Manual on Operation and Maintenance of water supply
systems, 2005, MoUD, GOI
1.4 Where the Standards and Specifications for any of the above work are not given, Good
Industry Practice shall be adopted to the satisfaction of the Employers Engineer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 556
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 557
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The Contractor shall repair and rectify the Defects and deficiencies specified in this Appendix E-I of
Schedule-E.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 558
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3.7 Piping/valve/ traps/ fittings / Taps leakages - Shall be rectified/replaced within 2 hrs.
3.8 Instruments like gauges/sensors - Shall be rectified / replaced within 2 hrs.
3.9 Any damage to sanitary ceramic fixtures or CP fittings shall be replaced or rectified within
24 hours.
3.10 Essential spares to be available for immediate repair.
6.1 The plant should not remain nonfunctional for more than two hours in a month
7.1 The bins should not be allowed to overflow at any point of time and should be emptied
irrespective of pre-determined frequency of lifting the bins.
7.2 OWC maintenance should be backed by proper plan so that the organic waste does not get
accumulated for more than six hours
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 559
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Applicable permits, as required, relating to environmental protection and conservation shall have
been procured by the EMPLOYER in accordance with the provisions of this Agreement.
2.1 Architecture
Commencement Certificate, Intermediate Certificates, Occupancy Certificate and Completion
Certificate from local municipal body or designated authority for the buildings.
Town Planning Department remarks for applicable norms / zones / uses.
3.1 Civil & Structures
Forest department Clearance for clearing of site of trees and shrubs if required.
Water Connection from Public Health Engineering Department (State).
Provision and permit for connection to proposed municipal sewage collection system at
directed location from local municipal body.
Project Clearance from General Inspectorate for Emergency Situations.
Project Clearance from the Solid Waste Management Authority.
4.1 Electrical
Incoming Power Supply (Main and temporary): State electricity board or power supply
authority.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 560
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Substation & Elevators & Solar PV system: CEIG (chief electrical inspector to government) /
local statutory authority / PWD
License to Operate the Elevators from Ministry of Labour or relevant authority.
5.1 Fire Fighting
Preliminary approval from Chief Fire Officer prior to construction and final approval on
completion of project.
6.1 FDA Access Control & Security
Fire Detection & Alarm System - Compliance with IS:2189:1988, BIS: 15908 standards
and certification from the Regional Fire Officer / Chief Fire Officer.
7.1 Roads
MIDC/PWD clearance for connecting to the any existing road.
8.1 STP
If any hazardous waste is generated from the facility like used DG oil, used
batteries etc., the same should be handed over to only SPCB approved
agencies for handling hazardous waste.
Permit from the Municipal Corporation for disposal of inert in the land fill site
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 561
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contents
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 562
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annex-I
(See Clause 7.1.1)
Performance Security
Employer
WHEREAS:
(B) The Agreement requires the Contractor to furnish a Performance Security for due and faithful
performance of its obligations, under and in accordance with the Agreement, during the
Construction Period and Defects Liability Period (as defined in the Agreement) in a sum of Rs.
. Crore (Rupees . Crore) (the Guarantee Amount).
NOW, THEREFORE, the Bank hereby, unconditionally and irrevocably, guarantees and affirms as
follows:
1. The Bank hereby unconditionally and irrevocably guarantees the due and faithful performance
of the Contractors obligations during and under and in accordance with the Agreement, and
agrees and undertakes to pay to the Employer, upon its mere first written demand, and without
any demur, reservation, recourse, contest or protest, and without any reference to the Contractor,
such sum or sums up to an aggregate sum of the guarantee amount as the EMPLOYER shall
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 563
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
claim, without the EMPLOYER being required to prove or to show grounds or reasons for its
demand and/or for the sum specified therein.
A letter from the EMPLOYER, under the hand of an officer not below the rank of
[.of EMPLOYER], that the Contractor has committed default in the due and faithful
performance of all or any of its obligations under and in accordance with the Agreement shall
be conclusive, final and binding on the Bank. The Bank further agrees that the EMPLOYER
shall be the sole judge as to whether the Contractor is in default in due and faithful performance
of its obligations during and under the Agreement and its decision that the Contractor is in
default shall be final, and binding on the Bank, notwithstanding any difference between the
EMPLOYER and the Contractor, or any dispute between them pending before any court,
tribunal, arbitrators or any other authority or body, or by the discharge of the Contractor for
any reason whatsoever.
In order to give effect to this Guarantee, the EMPLOYER shall be entitled to act as if the Bank
were the principal debtor and any change in the constitution of the Contractor and/or the
Bank, whether by their absorption with any other body or corporation or otherwise, shall
not in any way or manner affect the liability or obligation of the Bank under this Guarantee.
1. It shall not be necessary, and the Bank hereby waives any necessity, for the EMPLOYER to
proceed against the Contractor before presenting to the Bank its demand under this Guarantee.
2. The EMPLOYER shall have the liberty, without affecting in any manner the liability of the
Bank under this Guarantee, to vary at any time, the terms and conditions of the Agreement or to
extend the time or period for the compliance with, fulfillment and/or performance of all or any
of the obligations of the Contractor contained in the Agreement or to postpone for any time,
and from time to time, any of the rights and powers exercisable by the EMPLOYER
against the Contractor, and either to enforce or forbear from enforcing any of the terms and
conditions contained in the Agreement and/or the securities available to the EMPLOYER, and
the Bank shall not be released from its liability and obligation under these presents by any
exercise by the EMPLOYER of the liberty with reference to the matters aforesaid or by reason
of time being given to the Contractor or any other forbearance, indulgence, act or omission
on the part of the EMPLOYER or of any other matter or thing whatsoever which under any
law relating to sureties and guarantors would but for this provision have the effect of releasing
the Bank from its liability and obligation under this Guarantee and the Bank hereby waives all
of its rights under any such law.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 564
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3. This Guarantee is in addition to and not in substitution of any other guarantee or security now
or which may hereafter be held by the EMPLOYER in respect of or relating to the Agreement
or for the fulfillment, compliance and/or performance of all or any of the obligations of the
Contractor under the Agreement.
4. Notwithstanding anything contained herein before, the liability of the Bank under this
Guarantee is restricted to the Guarantee amount and this Guarantee will remain in force for the
period specified in paragraph 8 below and unless a demand or claim in writing is made by the
EMPLOYER on the Bank under this Guarantee all rights of the EMPLOYER under this
Guarantee shall be forfeited and the Bank shall be relieved from its liabilities hereunder.
5. The Performance Security shall cease to be in force and effect 90 (ninety) days after the end of
the Defects Liability Period as set forth in Clauses 7.1
6. The Bank undertakes not to revoke this Guarantee during its currency, except with the
previous express consent of the EMPLOYER in writing, and declares and warrants that it has
the power to issue this Guarantee and the undersigned has full powers to do so on behalf of the
Bank.
Any notice by way of request, demand or otherwise hereunder may be sent by post
addressed to the Bank at its above referred branch, which shall be deemed to have been duly
authorized to receive such notice and to effect payment thereof forthwith, and if sent by post it
shall be deemed to have been given at the time when it ought to have been delivered in due
course of post and in proving such notice, when given by post, it shall be sufficient to prove that
the envelope containing the notice was posted and a certificate signed by an officer of the
EMPLOYER that the envelope was so posted shall be conclusive.
1. This Guarantee shall come into force with immediate effect and shall remain in force and effect
for up to the end **** month in the year ***** or until it is released earlier by the EMPLOYER
pursuant to the provisions of the Agreement.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 565
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
by: (Signature)
(Name)
(Designation) (Code
Number) (Address)
NOTES:
(i) The bank guarantee should contain the name, designation and code number of the officer(s)
signing the guarantee.
(ii) The address, telephone number and other details of the head office of the Bank as well as of
issuing branch should be mentioned on the covering letter of issuing branch.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 566
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annex-II
(Schedule-G)
(See Clause 7.5.3)
Form for Guarantee for Withdrawal of Retention Money
..
.EMPLOYER,
Mumbai
WHEREAS:
[Name and address of contractor] (hereinafter called the Contractor) has executed an agreement
(hereinafter called the Agreement) with the [name and address of the EMPLOYER], (hereinafter
called the EMPLOYER) for the Design , Construction and Maintenance of AURIC Hall Building for
Phase-I in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC Basis (Package - IV)
on Engineering, Procurement and Construction (the EPC) basis, subject to and in accordance with the
provisions of the Agreement.
a. in accordance with the Clause 7.5.3 of the Agreement, whenever the amount of the retention
money (hereinafter called Retention Money) held by the EMPLOYER exceeds 1%
(one per cent) of the Contract Price, the Contractor may, at its option, withdraw the
Retention Money after furnishing to the EMPLOYER a bank guarantee for an amount equal to
the proposed withdrawal.
NOW, THEREFORE, the Bank hereby, unconditionally and irrevocably, guarantees and affirms as
follows:
1. The Bank hereby unconditionally and irrevocably undertakes to pay to the EMPLOYER, upon
its mere first written demand, and without any demur, reservation, recourse, contest or protest,
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 567
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
and without any reference to the Contractor, such sum or sums up to an aggregate sum of the
Guarantee Amount as the EMPLOYER shall claim, without the EMPLOYER being required to
prove or to show grounds or reasons for its demand and/or for the sum specified therein.
A letter from the EMPLOYER, under the hand of an officer not below the rank of
[.of EMPLOYER], that the Contractor has committed default in the due and
faithful performance of all or any of its obligations under and in accordance with the Agreement
shall be conclusive, final and binding on the Bank. The Bank further agrees that the
EMPLOYER shall be the sole judge as to whether the Contractor is in default in due and faithful
performance of its obligations during and under the Agreement and its decision that the
Contractor is in default shall be final, and binding on the Bank, notwithstanding any difference
between the EMPLOYER and the Contractor, or any dispute between them pending before any
court, tribunal, arbitrators or any other authority or body, or by the discharge of the Contractor
for any reason whatsoever.
1. In order to give effect to this Guarantee, the EMPLOYER shall be entitled to act as if the Bank
were the principal debtor and any change in the constitution of the Contractor and/or the
Bank, whether by their absorption with any other body or corporation or otherwise, shall
not in any way or manner affect the liability or obligation of the Bank under this Guarantee.
2. It shall not be necessary, and the Bank hereby waives any necessity, for the EMPLOYER to
proceed against the Contractor before presenting to the Bank its demand under this Guarantee.
3. The EMPLOYER shall have the liberty, without affecting in any manner the liability of the
Bank under this Guarantee, to vary at any time, the terms and conditions of the Retention
Money and any of the rights and powers exercisable by the EMPLOYER against the
Contractor, and either to enforce or forbear from enforcing any of the terms and conditions
contained in the Agreement and/or the securities available to the EMPLOYER, and the Bank
shall not be released from its liability and obligation under these presents by any exercise by the
EMPLOYER of the liberty with reference to the matters aforesaid or by reason of time being
given to the Contractor or any other forbearance, indulgence, act or omission on the part of the
EMPLOYER or of any other matter or thing whatsoever which under any law relating to sureties
and guarantors would but for this provision have the effect of releasing the Bank from its liability
and obligation under this Guarantee and the Bank hereby waives all of its rights under any such
law.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 568
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4. This Guarantee is in addition to and not in substitution of any other guarantee or security now
or which may hereafter be held by the EMPLOYER in respect of or relating to the Retention
Money.
5. Notwithstanding anything contained hereinbefore, the liability of the Bank under this
Guarantee is restricted to the Guarantee amount and this Guarantee will remain in force for the
period specified in paragraph 8 below and unless a demand or claim in writing is made by the
EMPLOYER on the Bank under this Guarantee all rights of the EMPLOYER under this
Guarantee shall be forfeited and the Bank shall be relieved from its liabilities hereunder.
6. The guarantee shall cease to be in force and effect 90 (ninety) days after the end of then
Defects Liability Period specified in Clauses 17.1 of the Agreement.
7. The Bank undertakes not to revoke this Guarantee during its currency, except with the
previous express consent of the EMPLOYER in writing, and declares and warrants that it has
the power to issue this Guarantee and the undersigned has full powers to do so on behalf of the
Bank.
Any notice by way of request, demand or otherwise hereunder may be sent by post addressed
to the Bank at its above referred branch, which shall be deemed to have been duly authorized
to receive such notice and to effect payment thereof forthwith, and if sent by post it shall be
deemed to have been given at the time when it ought to have been delivered in due course of
post and in proving such notice, when given by post, it shall be sufficient to prove that the
envelope containing the notice was posted and a certificate signed by an officer of the
EMPLOYER that the envelope was so posted shall be conclusive.
1. This Guarantee shall come into force with immediate effect and shall remain in force and effect up to
the end **** month in the year ***** or until it is released earlier by the EMPLOYER pursuant to the
provisions of the Agreement.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 569
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(i) The bank guarantee should contain the name, designation and code number of the officer(s) signing
the guarantee.
(ii) The address, telephone number and other details of the head office of the Bank as well as of
issuing branch should be mentioned on the covering letter of issuing branch.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 570
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annex-III
(Schedule-G)
(See Clause 19.2)
Form for Guarantee for Advance Payment
..,
. EMPLOYER,
Mumbai
WHEREAS:
i. [name and address of contractor] (hereinafter called the Contractor) has executed an agreement
(hereinafter called the Agreement) with the [name and address of the EMPLOYER], (hereinafter called
the EMPLOYER) for the Design, Construction and Maintenance of AURIC Hall Building for Phase-
I in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC Basis (Package - IV) on
Engineering, Procurement and Construction (the EPC) basis, subject to and in accordance with the
provisions of the Agreement.
ii. in accordance with the Clause 19.2 of the Agreement the EMPLOYER shall make to the Contractor
an interest bearing advance payment (hereinafter called Advance Payment) equal to 10% (ten per
cent) of the contract price for mobilization expenses and acquisition of equipment; and that the Advance
Payment shall be made in three installments subject to the Contractor furnishing an irrevocable and
unconditional guarantee by a scheduled bank for an amount equal to the 110% amount of each
installment to remain effective till the complete and full repayment of the installment of the Advance
Payment as security for compliance with its obligations in accordance with the Agreement; and the
amount of (first/second/third) installment of the Advance Payment is Rs. **** cr. (Rupees ***** crore)
(the Guarantee Amount).
iii. We, ..through our branch at . (the Bank) have agreed to furnish
this bank guarantee (hereinafter called the Guarantee) for the Guarantee Amount.
NOW, THEREFORE, the Bank hereby, unconditionally and irrevocably, guarantees and affirms as
follows:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 571
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. The Bank hereby unconditionally and irrevocably guarantees the due and faithful repayment on
time of the aforesaid installment of the Advance Payment under and in accordance with the Agreement,
and agrees and undertakes to pay to the EMPLOYER, upon its mere first written demand, and without
any demur, reservation, recourse, contest or protest, and without any reference to the Contractor, such
sum or sums up to an aggregate sum of the guarantee amount as the EMPLOYER shall claim, without
the EMPLOYER being required to prove or to show grounds or reasons for its demand and/or for the
sum specified therein.
2. A letter from the EMPLOYER, under the hand of an officer not below the rank of
[of EMPLOYER], that the Contractor has committed default in the due and
faithful performance of all or any of its obligations for the repayment of the installment of the Advance
Payment under and in accordance with the Agreement shall be conclusive, final and binding on the Bank.
The Bank further agrees that the EMPLOYER shall be the sole judge as to whether the Contractor is in
default in due and faithful performance of its obligations during and under the Agreement and its
decision that the Contractor is in default shall be final, and binding on the Bank, notwithstanding any
difference between the EMPLOYER and the Contractor, or any dispute between them pending before
any court, tribunal, arbitrators or any other authority or body, or by the discharge of the Contractor for
any reason whatsoever.
3. In order to give effect to this Guarantee, the EMPLOYER shall be entitled to act as if the Bank were
the principal debtor and any change in the constitution of the Contractor and/or the Bank,
whether by their absorption with any other body or corporation or otherwise, shall not in any way
or manner affect the liability or obligation of the Bank under this Guarantee.
4. It shall not be necessary, and the Bank hereby waives any necessity, for the EMPLOYER to proceed
against the Contractor before presenting to the Bank its demand under this Guarantee.
5. The EMPLOYER shall have the liberty, without affecting in any manner the liability of the Bank
under this Guarantee, to vary at any time, the terms and conditions of the Advance Payment or to extend
the time or period of its repayment or to postpone for any time, and from time to time, any of the rights
and powers exercisable by the EMPLOYER against the Contractor, and either to enforce or forbear
from enforcing any of the terms and conditions contained in the Agreement and/or the securities
available to the EMPLOYER, and the Bank shall not be released from its liability and obligation under
these presents by any exercise by the EMPLOYER of the liberty with reference to the matters aforesaid
or by reason of time being given to the Contractor or any other forbearance, indulgence, act or omission
on the part of the EMPLOYER or of any other matter or thing whatsoever which under any law relating
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 572
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
to sureties and guarantors would but for this provision have the effect of releasing the Bank from its
liability and obligation under this Guarantee and the Bank hereby waives all of its rights under any such
law.
6. This Guarantee is in addition to and not in substitution of any other guarantee or security now or which
may hereafter be held by the EMPLOYER in respect of or relating to the Advance Payment.
7. Notwithstanding anything contained hereinbefore, the liability of the Bank under this Guarantee is
restricted to the Guarantee amount and this Guarantee will remain in force for the period specified in
paragraph 8 below and unless a demand or claim in writing is made by the EMPLOYER on the Bank
under this Guarantee all rights of the EMPLOYER under this Guarantee shall be forfeited and the
Bank shall be relieved from its liabilities hereunder.
8. The guarantee shall cease to be in force and effect 90 (ninety) days after the end of the one year from
the date of payment of the installment of the Advance Payment, as set forth in Clause 19.2 of the
Agreement.
9. The Bank undertakes not to revoke this Guarantee during its currency, except with the previous
express consent of the EMPLOYER in writing, and declares and warrants that it has the power to issue
this Guarantee and the undersigned has full powers to do so on behalf of the Bank.
10. Any notice by way of request, demand or otherwise hereunder may be sent by post addressed to
the Bank at its above referred branch, which shall be deemed to have been duly authorized to receive
such notice and to effect payment thereof forthwith, and if sent by post it shall be deemed to have been
given at the time when it ought to have been delivered in due course of post and in proving such notice,
when given by post, it shall be sufficient to prove that the envelope containing the notice was posted and
a certificate signed by an officer of the EMPLOYER that the envelope was so posted shall be
conclusive.
11. This Guarantee shall come into force with immediate effect and shall remain in force and effect for up
to the end **** month in the year ***** or until it is released earlier by the EMPLOYER pursuant to the
provisions of the Agreement.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 573
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(Signature)
(i) The bank guarantee should contain the name, designation and code number of the officer(s) signing
the guarantee.
(ii) The address, telephone number and other details of the head office of the Bank as well as of issuing
branch should be mentioned on the covering letter of issuing branch
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 574
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Schedule H shall be the detailed billing break up to be provided by the successful Bidder on award
of job, prior to signing of the Contract, which shall form part of Contract and shall be the basis of
payment milestones.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 575
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Schedule I - Drawings
(See Clause 10.2)
1.0 Drawings
In compliance of the obligations set forth in Clause 10.2 of this Agreement, the
Contractor shall furnish to the Employers Engineer, free of cost, all Drawings listed in
Appendix I-I of this Schedule-I.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 576
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4 STRUCTURAL DRAWINGS
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 577
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
6 HVAC Drawings
i All buildings air distribution system layout - all floors
ii All buildings chilled water & equipment layout - all floors
iii Cooling Load calculations
iv P & ID for chilled water and condenser water system
v Chiller plant room layout
vi Utility building HVAC layout - all floors
viii Technical data sheets for all equipment / items
7 Electrical Drawings
i Singe One Line Diagram (SLD)
ii All Buildings Electrical Room GA & Sectional Drawings
iii All Buildings Cable Carrier System Layout & Sectional Details for all Floor Plans
iv All Buildings Lighting & Small Power Layout for All Floor Plans
v All Buildings Earthing & Lighting Protection Layout
vi Overall Earthing and Lighting Layout
vii Solar PV System drawings
viii Electrical Equipment GA, Cable Tray Layouts
DOCUMENTS:
viii Load List
ix Power and Control Cable schedule and interconnection schedule
x Design calculations of all system and equipment
xi Control scheme and data sheets
xii All Data-sheets with "By Bidder" details
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 578
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 579
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 580
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
construction of the project components and submitted to the Employer duly and validly
prepared Stage Payment Statements for an amount not less than 80% (Eighty per cent) of the
Contract Price.
6.0 Schedule Completion Date
6.1 The Scheduled Completion Date shall occur on the 730th (Seven Hundred and Thirtieth) day
from the Appointed Date.
6.2 On or before the Scheduled Completion Date, the Contractor shall have completed
construction in accordance with this Agreement.
7.0 Extension of time
7.1 Upon extension of any or all of the aforesaid Project Milestones or the Scheduled
Completion Date, as the case may be, under and in accordance with the provisions of this
Agreement, the Project Completion Schedule shall be deemed to have been amended
accordingly.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 581
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.0 Tests
2.1 Architectural & Interior Finishes: Visual and physical check for all Architectural and
Interior finishes, including but not limited to flooring, painting, glazing, GRC cladding,
Murals, false ceiling, door hardware, cladding & dado, polishes, etc. Operations of doors,
windows, louvers shall also be checked.
2.2 Landscape / softscape works: Visual and physical check for softscape works, plants &
saplings, lawns, shrubs, irrigation system including sprinklers & drip irrigation, fountains,
water circulation and filtration system, etc., including performance verification.
2.3 Civil and Hardscape works: Visual check of construction to determine that all civil,
structural and hardscape works conform to the provisions of this Agreement. Physical test if
required by the client.
2.4 Entry Gates and Boom Barriers: Visual and physical check for Boom Barriers,
Automated Entry gate operations including performance verification for sensors, remote and
manual controls, etc.
2.5 Electrical: Visual and physical and commissioning test for HT and LT panels, Dry type
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 582
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
transformers, UPS, DG set, DC System, bus ducts, rising mains, distribution boards, power &
control cables, SCADA system, elevators, solar PV panels, lighting DBs, switches & sockets,
safety features, luminaires / lighting fixtures, street lighting and pole, power supply, grounding,
communication between luminaire to control panel and central control system, etc. including
performance verification.
The client/ Contractor has right to witness the test carried out on all the equipment.
2. Tests shall be carried out at the manufacturers' works under his care and expense.
3. All routine tests as specified by the applicable standard code shall be conducted. Type test
certificates for the switchgear panel and CB from a recognized testing organization shall be
furnished with the offer. If client / consultant wishes type test shall be carried out at laboratory
in the suppliers region in clients / consultants presence. The supplier shall also submit a list of
guaranteed technical particulars with the offer.
4 In addition specific tests shall be conducted to check mechanical and electrical operation and
switchboard wiring to this specification and approved schematic drawings.
a) A general visual check. This shall cover measurement of overall dimensions, location, number
and type of devices, terminal boxes, location and connection of terminals etc.
b) Manual and electrical operation of CB/Relays shall be checked under the worst conditions of
auxiliary supply voltage.
c) Dry insulation test with power frequency voltage shall be conducted for the main and auxiliary
circuits.
d) Insulation resistance of the main and auxiliary circuits shall be checked.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 583
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
e) Operation check shall be carried out for every control function as per the approved schematic
diagrams by manually stimulating the fault conditions and operation of control switches/relays
etc.
For equipment bought from other sub - suppliers certified test reports of tests carried out at the
manufacturer's works shall be submitted. Normally, all routine tests as specified in the relevant
standards shall be conducted by the sub - supplier at his works.
Routine tests: power frequency tests, manual operating mechanism tests, functional tests of
L.V. auxiliaries and relays, making and breaking capacity for switches and breaker, short time
withstand current tests, making and breaking capacities for earth switch.
Type tests: impulse dielectric tests, power frequency dielectric tests, temperature rise tests,
mechanical operating tests, verification of degree of protection, verification of electromagnetic
compatibility.
1 TESTS
A Routine tests: Routine test such as ratio test, open circuit test, short circuit test, no load test,
induced high voltage test, insulation resistant test, measurement of winding resistance etc. shall
be conducted as per IS: 2026. Including CT polarity test, earth continuity test, OLTC operation
test, oil dielectric test.
Type tests: Type tests if required by client / consultant shall be carried out at certified
laboratory of the suppliers area shall be carried out. If not required by client certificates for
type test carried out for similar rating of transformer shall be submitted by the supplier. Type
tests shall be carried out for temp. Rise, impulse voltage and short circuit analysis.
B Test certificates: Five copies of the routine test and type test certificates shall be submitted for
purchaser's record before dispatch of transformer, including test certificates of bought out
items.
Inspection
A. Inspection including witnessing routine tests will be carried out by purchaser or his authorized
representative.
B Vendor shall notify purchaser or his authorized representative in writing atleast fifteen days
prior to vendor's scheduled inspection tests.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 584
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1. CPRI Testing
2. Routine Test:
a) Physical variation and dimensional check To cross check dimensions with approved
GA drawings.
c) Continuity test shall be carried out for complete busbar system with continuity tester
or actual charging.
d) Functional check Operation of all the switchgears and control logic to be checked
after charging at works.
e) HV test 2500 V for 1 minute shall be applied and no tripping / Arching / Flashing
shall occur.
f) IR test 1000 V shall be applied through meggar and the value shall be more than 30
M ohms.
g) Polarity and Phase sequence test Shall be checked for each feeder with phase
sequence meter.
3. Type Test:
Type test certificates for all switchgears and panel of similar rated busbar shall be provided
for
1. The owner or his authorized representative may visit the works during manufacture of
equipment to assess the progress of work as well as to ascertain that only quality raw
materials are used for the same. He shall be given all assistance to carry out the inspection.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 585
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2. Detailed test procedure along with the facilities available at vendors works shall be
furnished along with the bid Owner's representative shall be given minimum four weeks
advance notice for witnessing the final testing. Test certificates including test records and
performances curves etc. shall be furnished by the vendor.
3. Equipment shall be tested to conform to the appropriate standards and the following tests
shall be conducted in the presence of purchaser's:
4. Functional tests, continuity tests and high voltage test on control panel to establish the
performance called for in the specification.
5. Power frequency voltage test on switch gear and mechanical / electrical operational check.
6. Routine tests for alternator as per IS: 4722.
7. Over speed test (1.2 times the rated speed for 2 minutes)
8. Transient response tests for sudden application and rejection of loads of 25%, 50%, 75%
and 100% of rated capacity.
2.6 HVAC: Visual and physical and commissioning test for HVAC cooling system, dampers,
VAV's, sensors, Ventilation system, drives, control gauges, instrumentations, flow meters,
automation, vibration & acoustic insulation, etc including performance verification.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 586
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Routine and types tests for various items of equipment shall be performed at the contractors
work and the test certificates furnished. Functional test shall be conducted at site.
1.2 The performance test to determine whether OR not the full indent of the specification is
met shall be conducted by the contractor. After notification to the Employers that the
installation has been completed and the plant has run continuously for a period of at
least two weeks, the contractor shall conduct under the direction of the Consultants and
in the presence of Employers representatives test, such test as specified to establish the
capacity of various equipment supplied and installed by the contractor.
1.3 The contractor shall operate test and adjust the air conditioning system units, fans,
motors, all air conditioning appliances including adjustment of regulators, dampers etc.
1.4 All test equipment, labour, operating personnel, oil and refrigerant required for this test
shall be furnished by the contractor to enable the plant to be put in continuous running
test for a period of 3 days after all other tests and adjustments have been made.
The contractor will be provided with electrical power water for testing by the client. The
performance test shall be conducted during peak summer and peak monsoon.
2.0 PROCEDURE
The inside and outside conditions will be recorded for 48 hrs. (2 days) duration on hourly basis.
The outside and inside Dry Bulb and Wet Bulb temperatures shall be recorded by the means of a
sling psychrometer with mercury thermometers. The relative humidity shall be computed from
the psychrometeric chart. The inside Dry Bulb temp. and relative humidity shall fall within the
specified limits.
The following aspects shall be checked before conducting the performance tests:
1) The outside conditions shall be as close to the design values as possible. The tests shall
be arranged during the peak summer and monsoon.
2) The internal loads of various spaces shall be close to the design values as far as possible.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 587
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5) Hourly readings of pressure, temperature, electrical current, voltage and power factor
shall be properly recorded
The capacity of the plant and various other equipment and accessories shall be ascertained as
follows.
The flow of air over the cooling coil will be measured by recording the velocity of air across
each filter placed before the cooling coil. The velocity shall be measured by means of end
anemometer
Air quantity across the filters = velocity of air across the filters in FPM x net filter area ( in sq. ft.
).
The wet bulb temperature of air entering the coil and that leaving the coil shall be measured. The
enthalpy of entering and leaving air shall be noted from the psychrometeric chart, corresponding
to the wet bulb temp. recorded
SAY,
2.4 Chiller:
One Chiller shall be tested for performance at Manufacturer works at 100%, 75%, 50% & 25% at
AHRI condition and at 100%, 75%, 50% and 25% at Design Conditions (at constant condenser
entering temperature) for verification of IKW/TR & Capacity as per submission of AHRI
selection data sheet. If the inspection is outside India, the contractor shall visit and witness the
test and shall submit photographs/proof to ascertain his witnessing the testing. The Client /
Consultant representative may also witness the test. The cost of their visit shall be borne by the
Client. However, necessary coordination shall be arranged by the Contractor for their visit.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 588
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
In case of failure of any equipment during testing, the Contractor shall be bound to arrange for
subsequent inspections. All the expenses (including travel, boarding etc.) for such inspections
shall be borne entirely by the Contractor.
The temperatures of inlet and outlet water, water flow and pressure drop shall be measured as
suggested for the condenser.
24
2.5 Compressor:
Same pressure gauge shall be used for different pressure measurements and the same
thermometers shall be used for different temperature measurements. The capacity of the
compressor shall be computed from the performance chart supplied by the manufacturer.
After the desired inside conditions are achieved, the quantity of air through every outlet shall be
measured. Air quantity in CFM = Air velocity at the outlet in FPM x effective area of the outlet
in Sq. Ft.
2.7 Fire Protection System: Visual and physical and commissioning test for complete
firefighting system equipments, internal & external hydrants, sprinklers, electric & diesel
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 589
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All air shall be trapped from the pipeline through hydrants & air valves. Each section of the
pipe shall be slowly filled with the water & allow to stand the water for few hours with the ends
closed.
Underground mains and lead-in connection shall be flushed at a flow rate of not less than 480
Ltrs. Per minute.
Provision shall be made for the disposal of water issuing from test outlets to avoid property
damage.
Acceptance Test: At the time of taking over, the hydrant system shall fulfill the following
acceptance tests:-
Starting up of the pressure suction (Jockey Pump): The pressure switch shall be set at (-)0.5
kg/cm2 below Required Pressure at the lower limit and 0.0 kg/cm2 at the upper limit. The
system drain shall be opened to cause a drop in the pressure. The Jockey Pump shall start as
soon as the pressure gauge needle falls down by (-) 0.5kg/cm2. The Jockey pump shall also
stop automatically when the system has been pressurised again upto set pressure 0.0kg/cm2.
The main electrical pump shall be set to start by (-) 1.5 kg/cm2 drop in pressure. An external
hydrant valve using a single length of hose and branch pipe shall be fully opened to cause a
drop of pressure in the system. At first, the jockey pump shall start when the pressure drops by
(-) 0.5 Kg/cm2. Further, drop in the pressure by (-) 1.5 Kg/cm2 should be allowed to test
automatic start-up of the electrical pump. The electrical pump shall continue to run atleast for 5
minutes and register rise in the pressure upto 0.0 Kg/cm2 the Jockey Pump shall be
automatically stop at this. The electrical pump shall be stopped manually by pressuring the stop
button.
After having the system got fully charged at 0.0 kg/cm2 the external hydrant valve using hose
and branch pipe at (ii) above shall be opened. When the pressure has dropped by (-) 1.5
Kg/cm2, the electric main pump shall come into operation automatically. After the main pump
has run for 5 minutes, the power supply in the pump house shall be switched off. The diesel
pump shall automatically come into operation immediately.
All these tests mentioned above shall be repeated after one hour interval. The result of all the
tests shall be identical again. After the system has satisfactorily withstood the above tests, it can
be taken over from the contractor.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 590
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Start-Up/System Testing:
It will be the responsibility of the Tendered to cause interim/stage inspection by the TAC/S.F.O
during execution of the work as and when so called for by the Employer / Architect and shall
carry out any rectification / modification as may be suggested by the Tariff Advisory
Committee (TAC) / Chief Fire Officer (CFO).
Soon after the work is completed, the contractor shall inform the TAC/CFO in writing with a
copy to the Architect / Employer for getting the complete system including all sub system and
instrumentation, control etc. thoroughly inspected and tested for satisfactory performance.
After satisfactory completion of tests of the systems by the TAC / CFO the contractor shall be
required to submit in built drawings on tracing cloth to the Architect which have been so
approved.
In addition to TAC, the contractor shall also be responsible for getting the system and
equipment tested and approved by other Statutory Authorities like the Area Fire Officer or the
State Fire Services as may be required.
Commissioning Of System:
Pressurised the fire hydrant system by running the main fire pump and after attaining the
required pressure shut off the pump.
Open bye-pass valve and allow the pressure to drop in the system. Check that the jockey pump
cuts-in and cuts-out at the pre-set pressure. If necessary adjust the pressure switch for the
jockey pump. Close bye-pass valve.
Open bye-pass valve and allow the water to flow into the fire water tank in order to avoid
wastage of water. The main fire pump should cut-in at the preset pressure and should not cut-
out automatically on reaching the normal line pressure. The main fire pump should stop only
by manual push button. However, the jockey pump should cut out as soon as the main pump
starts.
Switch off the main fire pump and test check the diesel engine driven pump in the same manner
as the electrically driven pump.
When the fire pumps have been checked for satisfactory working on automatic controls, open
fire hydrant simultaneously and allow the hose pipe to discharge water into the fire tank to
avoid wastage. The electrically driven pump should run continuously for eight hours so that its
performance can be checked.
Diesel engine driven pump should also be checked in the same manner as given in para above
by running for 8 hours.
Check each Hydrant valve, male and female couplings and branch pipes for compatibility with
each other. Any fitting which is found to be incompatible and does not fit into the other
properly, shall be replaced by the Contractor. Yard Hydrant valves shall be checked by opening
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 591
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3.0 Plumbing & Drainage: Visual and physical and commissioning test for Plumbing & drainage
system including water pressure, faucets & valves, sanitary fittings, flush tanks, urinals,
faucet & urinal sensors, leakages, etc. including performance verification.
Plumbing equipment fixtures, piping etc. shall be free of stampings, makings (except those
required by codes) iron cuttings & other foreign materials.
Hot, Cold & drinking water system shall be cleaned thoroughly filled & flushed with water.
The entire mechanical apparatus shall operate at full capacity without objectionable noise or
vibrations.
Test all plumbing system in the presence of the site Engineer/Supervisor/Engineer-in-charge &
ample advance notice to test dates. Provide all equipment materials & labour necessary for
inspection & tests & repair all work, not passing the tests. After repairs are made, repeat tests
until units system is found satisfactory, to the authorities. Carry out tests prior to concealing,
insulating or back filling over any piping No exceptions will be made.
Test entire system of soil, waste & vent piping by water after the roughing in is completed &
before the fixtures are set. After setting the fixtures, providing smoke test, after sealing all traps.
Water test: Test entire system or section of system by closing all opening in piping except the
highest opening & filling system with water to the point of overflow. If the system is tested in
sections, plug each opening except the highest opening of the section filled with water. Keep the
water in system or in portion under test of or atleast 45minutes before inspection starts with test
pressure/head lasting for two hours. The system must be tight at all joints.
Final Test: After fixture are set, test system with smoke as follows:-
Smoke Test : Fill traps with water, then introduce into system a pungent thick smoke produced
by one or more smoke machines. Then smoke appears at stacks on the roof, plug stacks & allow
pressure of 25mm water column to build up in system. Maintain pressure of 15 minutes before
inspection starts. The system shall be tight at all joints.
Test all down spouts or rain headers & their branches within the building by water as described
for the above soil, waste & vent system.
All water piping: Hydro-static test 150 PSI for a minimum of 2 hours without drop in pressure as
required.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 592
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
All tests on below grade lines shall be continued until backfilling on such lines is completed to
disclose any damage caused by backfilling.
All system shall be tested in sections as required to expedite the work on other trades & meet
construction schedules & final test on completion.
3.1 FDA & Public Address: Visual and physical test for Fire Alarm sensors / detectors, alarms /
hooters, Public address system, BMS, etc., including performance verification.
3.2 CCTV, Access Control & Surveillance: Visual and physical test for Security systems
including access control card readers and cards, CCTV cameras, monitors, recording and
retrieval system, Visitor management system, operating software & hardware, etc.,
including performance verification.
3.3 Road (Riding quality test): Riding quality of each lane of the carriageway shall be checked
with the help of a calibrated bump integrator and the maximum permissible roughness for
purposes of this Test shall be 1800 (Eighteen Hundred) mm for each kilometer.
3.4 Storm Water: Visual and physical test for Rain water drainage system, storm water drains,
manholes & manhole covers, rain water harvesting system, etc., including performance
verification.
3.5 STP: Visual and physical test for Sewage treatment plant, untreated and treated wastewater
quality & quantity for polluting parameters, electrical & mechanical equipments etc.,
including performance verification. It should be run successfully for one complete cycle before
handing over.
3.6 Other tests: The Employers Engineer may require the Contractor to carry out or cause
to be carried additional tests, in accordance with Good Industry Practice, for determining
the compliance of the project components with Standards and Specifications.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 593
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3.0 Audits
3.1 Environment Health and Safety Requirements: The Employers Engineer shall carry out a
check to determine conformity of the project components with the environmental requirements
set forth in Applicable Laws and Applicable Permits.
3.2 Safety Audit: The Employers Engineer shall carry out, or cause to be carried out, a safety
audit to determine conformity of the project components with the safety requirements and
Good Industry Practice.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 594
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contents
Provisional Certificate
Completion Certificate
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 595
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Provisional Certificate
(See Clause 12.2)
CONTRACTOR by
(Signature) (Signature)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 596
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Completion Certificate
(See Clause 12.4)
2. It is certified that, in terms of the aforesaid Agreement, all works forming part of Project Works
have been completed, and the Project Works is hereby declared fit for entry into operation on
this the ..day of ..20 ..
(Signature)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 597
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.2 Any deduction made on account of non-compliance with the maintenance Requirements shall not
be paid even after compliance subsequently. The deduction shall continue to be made every
month until compliance is done.
1.3 The Employers Engineer shall calculate the amount of payment reduction on the basis of
weightage in percentage assigned to non-conforming items as given in Paragraph 2.
1 (a) + (b) + (c) (of the applicable monthly maintenance amount) 20%
(a) Openings and glazing works (door, window, hatches, skylight, glazing 3%
coloured and otherwise etc.)
(i) Breakage or damage of openable shutters their finishes and accessories like 2%
handles, door closers, locks, vinyl, floor springs etc.
(ii) Repairs of fixed glazing, polycarbonate skylight, louvers, sealants, etc. 1%
(c) External stone cladding, flooring, ramps, paving, hardscape, facade 10%
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 598
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Table 3: Percentage reductions for HVAC and Firefighting, Plumbing and Drainage
Sr. No. Item/Defect/Deficiency Percentage
1 (a) + (b) (of the applicable monthly maintenance amount) 23%
(a) High Side HVAC (Chillers, Pumps, Cooling towers, 7%
AHUs, DX units, VRV units, Fans)
(i) Failure of any of the above systems. 3%
(ii) Leakages / breakages or damage of piping, traps, valves, 2%
(iii) Non maintenance of design temperature 2%
(b) Water Supply Network (Potable water, Recycled water) 4.5%
(i) Rising and distribution network repairs, 2.5%
(ii) Valve and flow meters repairs and calibrations, refilling of 2%
(c) Sewage collection network 4.5%
(i) De-silting, overflows in surrounding areas 2%
(ii) Man holes damages. 2.5%
(d) Low side HVAC, firefighting, plumbing and drainage 7%
(i) Damage or leakage of Piping, traps, fittings, Gauges, sensors 2%
(ii) Damage to Sprinklers, firefighting equipments 2%
(iii) Breakage or leakage of Sanitary Ceramic and CP fixtures 3%
Table 4: Percentage reductions for Fire Detection, Alarm system, Access Control, Surveillance
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 599
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.2 The amount to be deducted from monthly lump-sum payment for non-compliance of particular
item mentioned in Table-1 to 7 shall be calculated on a pro-rata basis for each of the above items as
under:
R=P/100*M*L1/L
Where
P= Percentage of particular item/non- compliance /Defect /deficiency for deduction. For example, in
Architecture and Civil works, if a broken flooring/tile is not repaired/replaced within 48 hours,
the percentage of non-compliance item P is 3%.
M = Monthly lump-sum payment for maintenance in accordance with the Contract Agreement.
A1= Non-complying area (sqm) of the particular Item.
A= Total area (sqm) of the particular Item.
R= Reduction (the amount to be deducted for noncompliance for a particular item /Defect
/deficiency).
The total amount of reduction shall be arrived at by summation of reductions for such
items/Defects/deficiencyornoncompliance.
For any Defect in a part of 10 sqm, the non-conforming area shall be taken as minimum 10 sqm.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 600
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contents
2 - Terms of Reference
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 601
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1 The provisions of t h e Model Request for Proposal for Selection of Technical Consultants,
issued by the Ministry of Finance in May 2009, or any substitute thereof shall apply for
selection of an experienced firm to discharge the functions and duties of an EMPLOYERs
Engineer.
1.2 In the event of termination of the Technical Consultants appointed in accordance with the
provisions of Paragraph 1.1, the EMPLOYER shall appoint another firm of Technical
Consultants forthwith and may engage a government-owned entity in accordance with the
provisions of Paragraph 3 of this Schedule-N.
2. Terms of Reference
The Terms of Reference for the EMPLOYERs Engineer (the TOR) shall substantially
conform with Annex 1 to this Schedule N.
Notwithstanding anything to the contrary contained in this Schedule, the EMPLOYER may in its
discretion appoint a government-owned entity as the EMPLOYERs Engineer; provided that
such entity shall be a body corporate having as one of its primary functions the provision of
consulting, advisory and supervisory services for engineering projects; provided further that a
government-owned entity which is owned or controlled by the EMPLOYER shall not be eligible
for appointment as EMPLOYERs Engineer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 602
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annex I
(Schedule - N)
Terms of Reference for Employers Engineer
1.0 Scope
1.1 These Terms of Reference (the TOR) for the EMPLOYERs Engineer are being specified
pursuant to the EPC Agreement dated........... (the Agreement), which has been entered into
between the . Name of EMPLOYER (the EMPLOYER) and .......... (the
Contractor) for Design, Construction and Maintenance of AURIC Hall Building for Phase-I
in Shendra-Bidkin industrial area, Aurangabad, Maharashtra state on Engineering, Procurement &
Construction (EPC) Basis, and a copy of which is annexed hereto and marked as Annex-A
to form part of this TOR.
1.2 The TOR shall apply to design, construction and maintenance of the Project Roads and
Services
3.0 General
3.1 The EMPLOYERs Engineer shall discharge its duties in a fair, impartial and efficient
manner, consistent with the highest standards of professional integrity and Good Industry
Practice.
3.2 The EMPLOYERs Engineer shall perform the duties and exercise the authority in
accordance with the provisions of this Agreement, but subject to obtaining prior written
approval of the EMPLOYER/PMNC before determining:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 603
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4 .0 Construction Period
4.1 During the Construction Period, the EMPLOYERs Engineer shall review the Reports, Designs
and Drawings furnished by the Contractor along with supporting data, including the geo-
technical and hydrological investigations, characteristics of materials from borrow areas and
quarry sites, topographical surveys, and the recommendations of the Safety Consultant in
accordance with the provisions of Clause 10.1.6. The EMPLOYERs Engineer shall complete
such review and send its observations to the EMPLOYER/ PMNC and the Contractor within 15
(fifteen) days of receipt of such Reports, Designs and Drawings; provided, however that in case
of a Structure, the aforesaid period of 15 (fifteen) days may be extended up to 30 (thirty) days.
In particular, such comments shall specify the conformity or otherwise of such Drawings with
the Scope of the Project and Specifications and Standards.
4.2 The EMPLOYERs Engineer shall review any revised Reports, Designs and Drawings sent to it
by the Contractor and furnish its comments within 10 (ten) days of receiving such Reports,
Designs and Drawings.
4.3 The EMPLOYERs Engineer shall review the (a) Quality Assurance Plan (b) Health, Safety and
Environmental Management Plan submitted by the Contractor and shall convey its comments to
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 604
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
the Contractor within a period of 21 (twenty-one) days stating the modifications, if any, required
thereto. The Employers Engineer shall ensure the Contractors Project Management
requirements, BIM and CAD requirements regularly on a monthly basis to the Employer/
PMNC.
4.4 The EMPLOYERs Engineer shall complete the review of the methodology proposed to be
adopted by the Contractor for executing the Works, and convey its comments to the Contractor
within a period of 10 (ten) days from the date of receipt of the proposed methodology from
the Contractor.
4.5 Deleted.
4.6 The EMPLOYERs Engineer shall review the monthly progress report furnished by the
Contractor and send its comments thereon to the EMPLOYER/ PMNC and the Contractor
within 7 (seven) days of receipt of such report.
4.7 The EMPLOYERs Engineer shall inspect the Construction Works and the Project Roads
and shall submit a monthly Inspection Report bringing out the results of inspections and the
remedial action taken by the Contractor in respect of Defects or deficiencies. In particular, the
EMPLOYERs Engineer shall include in its Inspection Report, the compliance of the
recommendations made by the Safety Consultant.
4.8 The EMPLOYERs Engineer shall conduct the pre-construction review of manufacturer's test
reports and standard samples of manufactured Materials, and such other Materials as the
EMPLOYERs Engineer may require.
4.9 For determining that the Works conform to Specifications and Standards, the EMPLOYERs
Engineer shall require the Contractor to carry out, or cause to be carried out, tests at such time and
frequency and in such manner as specified in the Agreement and in accordance with Good Industry
Practice for quality assurance. For purposes of this Paragraph 4.9, the tests specified in the relevant
Codes or any modification/substitution thereof and standards for shall be deemed to be tests
conforming to Good Industry Practice for quality assurance.
4.10 The EMPLOYERs Engineer shall test check at least 20 (twenty) percent of the quantity or
number of tests prescribed for each category or type of test for quality control by the Contractor.
4.11 The timing of tests referred to in Paragraph 4.9, and the criteria for acceptance/ rejection of
their results shall be determined by the EMPLOYERs Engineer in accordance with the Quality
Control Manuals and/or the relevant Codes and Standards. The tests shall be undertaken on a
random sample basis and shall be in addition to, and independent of, the tests that may be
carried out by the Contractor for its own quality assurance in accordance with Good Industry
Practice.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 605
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4.12 In the event that results of any tests conducted under Clause 11.10 establish any Defects or
deficiencies in the Works, the EMPLOYERs Engineer shall require the Contractor to carry out
remedial measures.
4.13 The EMPLOYERs Engineer may instruct the Contractor to execute any work which is
urgently required for the safety of the Project Works, whether because of an accident,
unforeseeable event or otherwise; provided that incase of any work required on account of a
Force Majeure Event, the provisions of Clause 21.6 shall apply.
4.14 In the event that the Contractor fails to achieve any of the Project Milestones, the
EMPLOYERs Engineer shall undertake a review of the progress of construction and identify
potential delays, if any. If the EMPLOYERs Engineer shall determine that completion of the
Project Works is not feasible within the time specified in the Agreement, it shall require
the Contractor to indicate within 15 (fifteen) days the steps proposed to be taken to expedite
progress, and the period within which the Project Completion Date shall be achieved. Upon
receipt of a report from the Contractor, the EMPLOYERs Engineer shall review the same and
send its comments to the EMPLOYER/ PMNC and the Contractor forthwith.
4.15 The EMPLOYERs Engineer shall obtain from the Contractor two copies of all the Contractors
quality control records and documents before the Completion Certificate is issued pursuant to
Clause 12.4.
4.16 EMPLOYERs Engineer may recommend to the EMPLOYER/ PMNC suspension of the whole
or part of the Works if the work threatens the safety of the Users and pedestrians. After the
Contractor has carried out remedial measure, the EMPLOYERs Engineer shall inspect such
remedial measures forthwith and make a report to the EMPLOYER recommending whether or
not the suspension hereunder may be revoked.
4.17 In the event that the Contractor carries out any remedial measures to secure the safety of
suspended works and Users, and requires the EMPLOYERs Engineer to inspect such works,
the EMPLOYERs Engineer shall inspect the suspended works within 3 (three) days of receiving
such notice, and make a report to the EMPLOYER/ PMNC forthwith, recommending whether or
not such suspension may be revoked by the EMPLOYER.
4.18 The EMPLOYERs Engineer shall carry out, or cause to be carried out, all the Tests specified
in Schedule-K and issue a Completion Certificate or Provisional Certificate, as the case may be.
For carrying out its functions under this Paragraph 4.18 and all matters incidental thereto, the
EMPLOYERs Engineer shall act under and in accordance with the provisions of Article 12 and
Schedule-K.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 606
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
5.1 The EMPLOYERs Engineer shall aid and advise the Contractor in the preparation of its
monthly Maintenance Programme and for this purpose carry out a joint monthly inspection with
the Contractor.
5.2 The EMPLOYERs Engineer shall undertake regular inspections, at least once every month, to
evaluate compliance with the Maintenance Requirements and submit a Maintenance
Inspection Report to the EMPLOYER/ PMNC and the Contractor.
5.3 The EMPLOYERs Engineer shall specify the tests, if any, that the Contractor shall carry out,
or cause to be carried out, for the purpose of determining that the Project Works is in
conformity with the Maintenance Requirements. It shall monitor and review the results of
such tests and the remedial measures, if any, taken by the Contractor in this behalf.
5.4 In respect of any defect or deficiency referred to in Paragraph 3 of Schedule-E, the
EMPLOYERs Engineer shall, in conformity with Good Industry Practice, specify the
permissible limit of deviation or deterioration with reference to the Specifications and Standards
and shall also specify the time limit for repair or rectification of any deviation or
deterioration beyond the permissible limit.
5.5 The EMPLOYERs Engineer shall examine the request of the Contractor for closure of any
lane(s)/utilities lines of the Project Roads and/or Services for undertaking maintenance/repair
thereof, and shall grant permission with such modifications, as it may deem necessary, within 5
(five) days of receiving a request from the Contractor. Upon expiry of the permitted period of
closure, the EMPLOYERs Engineer shall monitor the reopening of such lane(s), and in case of
delay, determine the Damages payable by the Contractor to the EMPLOYER under Clause 14.5.
7.0 Payments
7.1 The EMPLOYERs Engineer shall withhold payments for the affected works for which the
Contractor fails to revise and resubmit the Drawings to the EMPLOYERs Engineer in
accordance with the provisions of Clause 10.2.4 (d).
7.2 EMPLOYERs Engineer shall -
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 607
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(a) within 10 (ten) days of receipt of the Stage Payment Statement from the Contractor pursuant to
Clause 19.4, determine the amount due to the Contractor and recommend the release of 90
(ninety) percent of the amount so determined as part payment, pending issue of the Interim
Payment Certificate; and
(b) within 15 (fifteen) days of the receipt of the Stage Payment Statement referred to in Clause
19.4, deliver to the EMPLOYER/ PMNC and the Contractor an Interim Payment Certificate
certifying the amount due and payable to the Contractor, after adjustments in accordance with
the provisions of Clause19.10.
7.3 The EMPLOYERs Engineer shall, within 15 (fifteen) days of receipt of the Monthly
Maintenance Statement from the Contractor pursuant to Clause19.6, verify the Contractors
monthly statement and certify the amount to be paid to the Contractor in accordance with the
provisions of the Agreement.
7.4 The EMPLOYERs Engineer shall certify final payment within 30 (thirty) days of the receipt of
the final payment statement of Maintenance in accordance with the provisions of Clause 19.16.
9. 0 Miscellaneous
9.1 A copy of all communications, comments, instructions, Drawings or Documents sent by the
EMPLOYER's Engineer to the Contractor pursuant to this TOR, and a copy of all the test results
with comments of the EMPLOYER's Engineer thereon, shall be furnished by the EMPLOYER's
Engineer to the EMPLOYER/PMNC forthwith.
9.2 The EMPLOYER's Engineer shall retain at least one copy each of all Drawings and
Documents received by it, including 'as-built' Drawings, and keep them in its safe custody.
9.3 Within 90 (ninety) days of the Project Completion Date, the EMPLOYER's Engineer shall
obtain a complete set of as-built Drawings, in 2 (two) hard copies and in micro film form or in
such other medium as may be acceptable to the EMPLOYER, reflecting the Project
............................................. as actually designed, engineered and constructed, including an as-
built survey illustrating the layout of the Project Works and setback lines, if any, of the buildings
and structures forming part of Project Facilities; and shall hand them over to the EMPLOYER
against receipt thereof.
9.4 The EMPLOYER's Engineer, if called upon by the EMPLOYER/PMNC or the Contractor or
both, shall mediate and assist the Parties in arriving at an amicable settlement of any Dispute
between the Parties.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 608
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
9.5 The EMPLOYER's Engineer shall inform the EMPLOYER/PMNC and the Contractor of any
event of Contractor's Default within one week of its occurrence.
9.6 The Employers Engineer, if called upon by the Employer/ PMNC, shall attend the meetings on
Project reviews, discussions to be held at Employer/ PMNC office with required reports and
presentations.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 609
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contents
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 610
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 611
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Schedule P - Insurance
(See Clause 20.1)
Contents
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 612
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 613
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
(a) the EMPLOYERs right to have the construction works executed on, over, under, in or through
any land, and to occupy this land for the Works; and
(b) Damage which is and unavoidable result of the Contractors obligations to execute the Works.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 614
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contents
1 - Objective........................................................................................................................
2 - General...........................................................................................................................
3 BIM Modelling...............................................................................................................
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 615
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
1.1 OBJECTIVE
The Employer mandates the use of advanced computer based dynamic 3D-model driven
approach for the detailed planning, design, engineering, construction and operation of the
DMIC nodes to allow simulation, visualization and engineering analysis of all
transportation, utility, building, civil works and geospatial infrastructures.
This includes an aggregate dynamic 3D Building Information Model (BIM) for the city
infrastructure systems with 3D building models. 3D civil infrastructures, 3D models for
rail, roads and underground and above ground utilities systems participating.
3D infrastructure modelling tools shall be used to develop and produce project models and
simulations (e.g. in case of natural calamity etc.) as required for submittals.
The 3D infrastructure Information Models are to be used throughout the design,
construction and operational life-cycle of the asset, including but not limited to for system
collision detections, materials quantification, construction sequencing and carbon impact
analysis.
3D infrastructure models use shall be maximized for project reviews, decision support,
design analysis, and quality assurance during all phases of this program.
2.1 GENERAL
2.2 Purpose
2.1.1. The purpose of the 3D Building Information Modelling (BIM) requirements describes the use
of computer aided design (CAD), geographical information (GIS) and building
information modelling (BIM) for the work under the Contract.
2.1.2. These requirements shall be used as a reference for the Design & Build Contractor to develop
specific Work Package BIM Execution Plan (BEP) that shall detail the specific CAD/GIS/BIM
software used within the Work Package to control the specific BIM and CAD process. The
outputs from this process will be drawings and 3D models as PDFs that will be input to the
Project Management Information System (PMIS) for distribution.
2.1.3. BEPs establish the methodology for managing the production, distribution and quality of the
design information generated by CAD, GIS and BIM systems, using a disciplined process for
collaboration and a specified file and model naming policy.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 616
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
BIM Project Execution Plan Overview Information: Document the reason for creating the
Project Execution Plan.
Project Information: The Plan should include critical project information such as project
numbers, project location, project description, and critical schedule dates for future reference.
Key Project Contacts: As part of the reference information, A BIM Plan should include contact
information for key project personnel.
Project Goals / BIM Objectives: This section should document the strategic value and specific
uses for BIM on the project as defined by the project team in the initial step of the planning
procedure.
Organizational Roles and Staffing: One of the primary tasks is to define the coordinator(s) of
the BIM planning and execution process throughout the various stages of the project. This is
particularly important when identifying the organization(s) who will initiate the development of
the BIM Plan, as well as the required staff to successfully implement the plan.
BIM Process Design: This section should clearly illustrate the execution process through the use
of process maps which are developed in the second step of the planning procedure.
BIM Information Exchanges: The model elements and level of detail required to implement
each BIM use should be clearly defined in the information exchanges requirements.
BIM and Facility Data Requirements: The owners requirements for BIM must be documented
and understood.
Collaboration Procedures: The team should develop their electronic and collaboration activity
procedures. This includes the definition of model management procedures (e.g., file structures,
and file permissions) as well as typical meeting schedules and agendas.
Model Quality Control Procedures: A procedure for ensuring that the project participants meet
the defined requirements should be developed and monitored throughout the project.
Technology Infrastructure Needs: The hardware, software and network infrastructure required
to execute the plan should be defined.
Model Structure: The team should discuss and document items such as model structure, file
naming structure, coordinate system, and modeling standards.
Project Deliverables: The team should document deliverables required by the owner.
Delivery Strategy / Contracts: This section should define the delivery strategy which will be
used on the project.
2.3 Scope
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 617
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.3.1 This BIM requirement document outlines the roles and responsibilities that are necessary for
a successful collaborative 3D Building Information Modelling (BIM) approach.
2.3.2 The Project Management Information System (PMIS) and Common Data Environment
(CDE) will be mandated for the structure and the controlled sharing of the building
information with known provenance and status in a multi-disciplinary environment.
2.3.3 Contractors BEPs are required to control the production and coordination of the design
information within each Works Package.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 618
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.5.1 BIM uses that have been established as required thus far are:
BIM Uses Description/Comments
Existing Conditions This will require the gathering of existing conditions information from a
Modelling range of sources, and validating the quality, accuracy and reliability of that
information for use on the project. The physical extent of what is needed
to be modelled is to be determined, based on location,
physical/spatial/visual relationship and potential impact on the project.
Areas or elements identified as posing risk to the project should be
communicated clearly to inform future risk mitigation efforts. In the
Site Analysis The site context should be understood thoroughly and acknowledged
within the design, accounting for factors that may impact on siting/position
of proposed construction works, such as interfaces with existing structure
or services, vistas, nearby land use, hydraulic analysis, geotech and
topographic conditions, site access/egress issues, traffic flows, other
infrastructure and so on.
Design Authoring A process in which software is used to develop a Building Information
Model based on criteria important to the communication of the building's
design. Two types of software applications are core to the BIM-based
design process: design authoring tools and audit and analysis tools.
Authoring tools are used to create models while audit and analysis tools
draw from or enhance the richness of information in a model. Most audit
and analysis tools can be used for Design Reviews and Engineering
Analysis BIM Uses. Design authoring tools are required in the first
instance, and employ a powerful database of properties, quantities, means
Design Visualization The BIM can be used to generate rendered images, animated fly-throughs
and read-only versions of the model as requested by the Client (with due
notice) to support effective communication of the design intent of the
building. This is critical for stakeholder engagement at a number of levels
and project stages
Interference General coordination will take place during early design via visual
Detection inspection and design coordination workshops. In particular, coordination
efforts will be applied to key pinch points, such as cores, risers, plenum
spaces, and plant areas. Aggregation/intensity of interferences detected
will further inform priority zones and element types. Late in the design
process, and particularly for preconstruction planning (during early
Construction stage), interference severity criteria will be defined and
interference rules configured that will support element-level coordination.
Good interference rule definitions will be key to avoiding false positives
Design Review A process in which stakeholders interrogate and interact with a 3D model
to validate various design criteria. These may include evaluating the
ability to meet the program, previewing spatial or visual relationships in a
virtual environment, layout, sightlines, lighting, security, ergonomics,
acoustics, textures and colours, etc. This BIM use can be achieved with the
BIM ft t d di l d t d i th d l
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 619
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
2.6 Definitions
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 620
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Workspace: A predefined folder structure containing configuration and content relevant to the
specific application.
Master Document Index (MDI): A list of agreed model file and drawing deliverables produced
by the Contractor against agreed milestones.
2D/3D Model: A design model with entities having two/three-dimensional properties which are
coordinated to the agreed geospatial reference system.
Model composite: A model file containing multiple references of 2D/3D models coordinated
using a common geospatial reference system to form a complete model representation of the
information.
Model extraction: A 2D model file containing elements generated from an external 3D model,
usually in the form of sections, elevations and plans. Can contain graphical or non-graphical
content.
Model files (MD2/MD3): Native CAD files that can be in the form of a 2D or 3D model.
Model rendition (MDR): Output from a model file, model renditions provide static snap-
shots in a form that enables the information to be viewed, printed and marked up.
Output file: A generated rendition of graphical or non-graphical information (a plan, section,
elevation, schedule, table or other view of a project).
Model view: The view within CAD files which contains entities or reference files using real
world coordinates
Originator: The author of models, drawing and documents.
Production drawing: An immutable electronic plot (PDF) produced from a drawing definition,
having received all necessary reviews prior to issue.
Zone: A manageable spatial 2D or 3D subdivision of a model allowing more than one person to
work on the model, floor plan or staircase etc. at a time. Each zone is a reference file and when
all references are viewed in a model composite the full model shall be represented.
Status: Defines the fitness of information in a model, drawing or document
WIP: Work In Progress: each individual company or disciplines own work. This is information
that has not been issued or shared with other parties. Refer to BS1192.
Shared: Information that has been reviewed and is available to other parties. Refer to BS1192.
Published: Documents and other data outputted from Shared information. Typically this shall
include contract drawings, reports and specifications but can also include information for data
exchange between BIM software, such as LandXML, IFC files. Refer to BS1192.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 621
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Component: An individual building element that can be reused. Examples include doors, stair
cores, furniture or internal room layouts, facade panels, etc. Components are typically inserted
and moved/rotated into the required position.
Assembly: A composition or collection of components and/or modelled elements arranged to
define part or all of a building model, structure or site. An Assembly typically contains
information that can be referenced without repositioning.
Container: An optional parent repository which can be used to compile assemblies and
components for specific purposes including export and publication. A Container can exist for
each individual profession/discipline or for multiple disciplines, for buildings or for a complete
project.
Layer/Level: Attribute given to entities within CAD files that enables their visibility to be
controlled. Further values may be assigned to the attribute to control whether it can be edited or
deleted.
IFC: Industry Foundation Class is a neutral and open specification file format. The data model
facilitates interoperability between object based software platforms.
LandXML: LandXML is a specialized XML data file format containing civil engineering and
survey measurement data commonly used in the Land Development and Transportation
Industries.
2.7 Responsibility
The Design and Build Contractor shall provide: A structured BIM approach to the production of
all required design and as built data and information for these Works under the Contract,
modelled on BS1192 Collaborative production of architectural, engineering and construction
information; Code of practice;
Evidence that an all discipline integration, coordination and resolution process has taken place
in a collaborative 3D object orientated CDE, the outputs of which meet or better the Employers
Requirements;
A uniform and interoperable software/hardware platform across the entire Work Package, in
that any software used shall be consistent with the principles of the sharing of multi-disciplinary
object data in a CDE; That data shall include geometry and object attributes; Compatibility
between software and hardware platforms, including processes for any interfaces with other
Work Packages, as to ensure seamless integration at all areas of overlap;
An Engineering Content Management System (ECM) which shall be configured to the CDE
workflows consistent with those set out in BS1192 and integrate with Employers PMIS
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 622
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 623
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Provides the focal point for all file and document management issues in the project.
Ensures that all information is compliant with standards and that each model or file has
been signed off fit for purpose.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 624
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Ensure that all CAD models and drawings are delivered to the SIA use agreed IT solutions, and
are according to the agreed project requirements.
Ensure that all object attribute data is structured and is compliant with the project SMPs Ref
BS1192. This role should be responsible to the Contractors BIM Manager.
Completion of a table of names assigned to the roles described above and submit it to the client
as a reference document.
Ensure that all drawing production shall be in line with CAD Guidelines given in Annexure I
of this Schedule Q.
2.8.1 The Contractor shall produce ECM system information sufficiently detailed to produce
traditional drawings or documents as views of multi-authored data.
2.8.2 The Contractor shall develop and utilize a suitable ECM system that allows for a suitable
permissions matrix, workflow, referencing, version control, process and information hierarchy
that is consistent with the principles of the CDE for all models and drawings.
2.8.3 The Contractor shall provide access to the ECM system for the Engineer.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 625
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3.2.7 Model files shall have a title box placed in the sheet view.
3.3 Coordinates
3.3.1 A common coordinate system for all BIM data and adopt it consistently for all Models. As a
priority the Client requires that Global Coordinates WGS 84, 43N shall be used.
3.4 Data Segregation (Zoning)
3.4.1 Each structure/Utility/Infrastructure shall be created in one file.
3.4.2 The BIM software in use will have a major impact on how the model is to be broken down,
but in all cases sub-division is required to maintain workable files using appropriate hardware.
3.5 Planning the Work & Data Segregation:
3.5.1 The supply chain shall agree, adopt and maintain a BIM Strategy focusing on the
following project-specific processes as a minimum:
Model Management
Zones and Areas
Naming Conventions
Publishing processes
3.5.2 Site Information: Minimum site information will as a digital default shall include:
Site Name
Site Status
Land Area (Ha)
Site Grouping
Address including Postcode
GIA of proposed asset(s)
Site Cross Reference
3.5.3 Floor Data: All floor layouts will include the following minimum digital data set as a default
Site Code
Block No
Floor Level
Floor Code
Floor Description
GIA (m2)
GEA (m2)
3.5.4 Room Data: All rooms will include the following minimum digital data set as a default:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 626
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Site Code
Block No
Floor Level
Room Number
Zone Name
Room Description
Room Area (m2)
Space Utilisation
Functional Suitability
Quality Room Height (m)
Volume
3.5.5 Asset data will be provided for the client CAFM and AMS Systems as attributes of objects
in the model with the following criteria:
Attribute Field Description
GUID 3D Model Generated Code.
Building
Name/Description
Asset Template
Name
Asset Template
Code
Local Enter with a relevant name for the asset as it could be identified on site
Name/Description (e.g. West AHU No1). This is the name defined in the design process.
In the case of individual assets created this will be one.
In the case of "grouped" assets it will be the count of the assets. e.g.
Fire Extinguishers; Fire Hose Reels; Lighting; Emergency
Quantity Lighting; FCUs; Eye Bolts. These are multi selected when defined in
Manufacturer The manufacturers name.
Model The model or reference of the asset.
The asset serial number, this typically is added to the model late in the
procurement and installation process and lends itself to being carried
Serial No. out via export, data entry and re-import. Where not applicable state
N/A.
Floor/Level The Level of the building or building zone.
Position Detailed description of location.
operating instructions
maintenance instructions
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 627
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 628
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 629
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
created in three grades: low, medium and high resolution. Modelling in this way allows
easier component management and simple swapping of the grades should additional, or less
detail be required. It also ensures the most efficient use of PC processing power at any
particular stage. The Contractors Work Package BIM strategy document shall address the
naming conventions for components, component grades, types, parameters, materials, etc. and
the quality assurance and filing of such elements. It shall give guidance on using downloaded
content.
3.10 Existing Infrastructure data sets
3.10.1 Employer shall share available existing data sets and models for contractor as reference.
3.10.2 Contractor shall be liable for validating the models before utilizing/enhancing them further.
3.10.3 The existing infrastructure and systems shall be modelled in sufficient detail as to provide
integration with the Works under the Contract.
3.10.4 Data sets with distinct owners, e.g. TP2E, TP2W, TP2E-Water etc. Shall be referenced into
the model. The data contained within these models shall remain under the authority of the
owner at all times.
Unresolved areas of non-coordination in structure/services/finishes/clashes shall be clearly
highlighted on the drawings and the model at all times. Provenance of all referenced data sets
shall be explicitly declared on all relevant models and subsequent drawings.
3.10.5 Any discrepancies with the data shall be reported back to the owner for their action.
3.11 4D & 5D
The contractor shall take full advantage of the 3D object attributes available in the BIM
environment to prove cost, constructional logic, fabrication, and program as required by the
employer.
3.12 Coordination and integration drawing packages
3.12.1 Within the BIM environment each of the disciplines shall reference other models in a timely
manner for coordination purposes. The head of each discipline group shall decide the
extent and nature of supporting discipline data that shall be displayed in each of their own
discipline drawing submissions. Clash detection software routines shall be run on the multi-
discipline model and on combined master models and any clashes resolved. The reports of
which will be submitted on request of the Engineer.
3.12.2 Specific drawing packages are required from each discipline. The drawings shall comprise of
2D extractions of the 3D design models from the CDE. These include, but not limited to the
examples below.
a) Buildings
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 630
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Architectural
Structural
Mechanical
Electrical
Building Services
b) Combined Services Drawings (CSDs) on
Structural/Civil/Architectural backgrounds:
c) CSDs covering the main installations including closed circuit television (CCTV),
power, fire systems, ventilation, lighting, and public address (PA), communications
and signage. These shall be submitted in logical readable packages.
d) Plan and Profile drawing extractions of linear infrastructure
e) General Arrangement Drawings
f) For detail of Models & Drawing.- See Annexure - II
3.12.3 All CAD drawings shall be comprised of 2D models extracted from the 3D master model. Any
subsequent design scheme changes that are required to be fully coordinated shall be
modelled in 3D and the drawing extraction re-run to produce revised plots.
3.12.4 All plot composition files shall be checked as prescribed by the workflow setup in the CDE
before submission to the Engineer.
3.13 Deliverables
3.13.1 The number and extent of the design & build submissions shall be detailed by the
Contractor in the MDI, which shall form part of the Contractors BEP.
3.13.2 All native design/analysis models shall be listed and submitted in MDI
3.13.3 All CAD drawings submission shall have the original plot composition files containing all
extractions.
3.13.4 All CAD drawings submissions shall have a simplified standalone 2D vector plot
composition file.
3.13.5 All CAD drawings submissions shall have a corresponding PDF.
3.13.6 All CAD drawings submission shall have their provenance shown on the plot, i.e. the
references, extractions, model revision used to generate plot.
3.13.7 All database and file store data from the Contractors ECM system.
3.13.8 BIM Deliverables:
Site Model
Massing Model
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 631
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Architectural Model
o For regulatory submissions
o For coordination and / or clash detection analysis
o For visualization
o For cost estimation
Schedule (material, time etc.) and phasing program (in BIM or spreadsheet)
Construction and fabrication models
Shop drawings.
As-built model (in native proprietary or open formats)
Data for facility management
Other additional value added BIM services
3.13.9 To support the development of a Project Information Model (PIM) and Asset Information
Model (AIM) at handover the information exchange formats will include the following
information from the same data set in a commonly accessible electronic formats:
2D portable format document drawings (.dwg and .pdf) cut from the native Model(s)
The native Model(s)
The model(s) in IFC format
Programme files .mpp
Text files (.doc and .pdf) for specification and all other tender docs
3.14 Master Document Index (drawing and model register)
3.14.1 The Contractor shall provide a MDI at the start of the Works that shall list all the file
identifiers for models and drawings that are needed, along with their delivery dates and
intermediate milestones. The following document properties (metadata) shall be included:
Company Code
Project Code
Design Stage
Discipline Code
Level
Location
Drawing Type
Revision
3.14.2 All CAD models and drawings shall be compiled in a MDI (spreadsheet) by the Contractor
prior to commencement of work. It shall list out all models and drawings to be submitted at
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 632
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 633
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
4D Construction / Latest
Engineering 5D Schedule Bentley Navigator
Design Review 3D BIM and GIS Autodesk Infraworks Latest
Tools Bentley Latest
integration/coordin MicroStation
GIS -Asset ESRI ArcMap Latest
GIS Windows 7
Management AutoCad MAP Latest
Publish read only i-model Plug-ins (64 Bit
single file Recommended)
containing For Revit
Publishing Latest
graphical and
For Adobe
non- graphical
(Reader)
attribute
3D/2D Models, Adobe Acrobat
Drawings and Reader
Maps
Engineering Maps ESRI ArcReader
Design Review 10
Tools
Autodesk DWG
3D/2D Models, TrueView
Drawings
Bentley View
*Products and product versions should be clearly stated in BEP and should be consistent across the
project.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 634
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Annex I
CAD Guideline
(Schedule - Q)
1 OVERVIEW
1.1 Purpose
Programme Manager for New Cities (CH2MHill) has initiated to manage a program that will
assist in standardizing the use of CAD across all departments. The primary goal is to create an
environment for seamless integration/collaboration between all disciplines & business lines of
all consultants/contractors regarding the use of CAD for production of any drawing. The
document will achieve this through setting out the Guideline for drawing data production. This
will then enable drawing data to be incorporated into the Aurangabad Industrial Township
limited (AITL) GIS.
1.2 Application
This CAD standard shall be applied to all disciplines in all offices and design houses working in
this Project. The scope of this document is to provide guidelines and procedures for adopting
AutoCAD layering standards in preparing design and as-built drawings for automated
transference to DMICDC GIS. This Guideline will address the following:
i. Layer assignments,
ii. Standard symbols
iii. Layers and layer names, iv. Attributes to each feature,
v. Templates,
vi. Colour usage associated with line widths for all Highways and Utility drawings.
The Guideline are to be applied for all drawings from Concept through to As Built handover
stage.
1.3 Acronyms
First, a few useful acronyms:
A-E Architect-Engineer
A/E/C Architecture, Engineering, and Construction
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 635
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 636
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Figure 1:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 637
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Contains all final published sheet files, figures or sketches. This folder must contain the last
issued Models/Xrefs. Data filed in this area shall never be deleted or overwritten, but
will remain until archived.
i. Within WIP folder each discipline can create a folder structure to suit its needs.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 638
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ii. Common resource files such as title sheets, mapping, surveys, imagery and other shared CAD
data must be available to all disciplines in the Shared area.
iii. Once data has been checked, verified and approved, it must be copied to the
Shared area and other disciplines notified.
iv. When models are revised or updated; other disciplines referencing the model will be affected,
so effective communication between disciplines is essential.
v. When data files have been authorised and verified for issue, it is copied to the Published area, to
maintain a local copy within the design organizations server.
vi. The previous version of the data in the Published area shall be moved to the
Archive area as a historical record and to maintain an audit trail.
2.7.1 Drawings
The Project Implementation Plan (PIP) will define the area where the hard-copies for projects
are to be filed.
The electronic version of the master plot of the drawing shall be known as the reference
master. The reference master, if required, shall be utilised for the electronic issue of the file.
All check prints are to be retained at least for the term of the project unless otherwise agreed
with the PMNC. No check prints are to be disposed of without the consent of the Project
Manager.
3 DRAWING DEVELOPMENT
3.1 Drawing Numbering System
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 639
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
The drawing numbers are to be entered into the drawing register during creation of the drawings
so as to eliminate duplicate drawing numbers being assigned. The drawing number shall be
unique for each drawing and will normally be in the form:
Table 1
Discipline /
Project Documen Drawing
Drawing
t code
Originator code - Type code - - Sheet No
Name Number
See
3.1.1 3.1.2 3.1.3 3.1.4 3.1.5
Reference
Working drawings shall not have the drawing status and revision in the file name.
Four digits sequential number for a specific drawing type series. Refer to Appendix C.
Subsequent issue of a drawing shall have the revision coding incremented by the next sequential
number or letter.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 640
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Note #3: Working drawings shall not have the drawing status and revision in the file name.
Proposed _Centre_
Example D2 CH2MHILL SBIA HW
- - - line
See
3.2.1 3.1.2 3.1.3 3.1.4 3.2.5
Reference
2D Model D2
3D Model D3
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 641
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
i) The top line shall identify the specific area or section within the contract, i.e. HIGHWAYS, or
it may be left blank where no such area or section exists.
ii) The second third and fourth lines shall identify the content or purpose of the drawing, i.e.
TRAFFIC SIGNS AND ROAD MARKINGS
iii) Where several drawings depict similar detail and no other qualifications are available for
distinguishing between them, the distinction shall be made by labelling each drawing
consecutively with sheet numbers, such as SHEET 1 OF 10, SHEET 2 OF 10, etc.
Figure 3
Table 5
Drawing Status
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 642
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Concept Design
Preliminary Design
Detailed Design
Tender
Contract
As Built
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 643
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Figure 7
Drawings that are issued under specific Submissions or Milestones sets shall have clear,
consistent revision description that states the purpose of the submission. e.g. ISSUED FOR
APPROVAL, etc.
Figure 8
The date shown in the revision history table shall be in the format DDMMMYY as highlighted
in Figure 9 below
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 644
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Figure 9
The date of completion of the revision and the initials of the person effecting the revision shall be
stated.
The earliest revision descriptions shall be deleted when there is no space to include the current
revision within the revision column.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 645
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Figure 10
Figure 11
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 646
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 647
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
3.3.11 Signatures
The revision history table shall contain the current issue revision number, date of issue,
Drafter/Author, Checker, Approver signatures or initials and description of current revision.
Table 7
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 648
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Original hand-signed copy is required for all Final drawings submitted for: Concept design,
Preliminary design, Detailed design, Tender set, Contract set, GFC drawings (during construction) and
As Built.
Subsequent hard copies of the submitted original do not have to be hand signed. Scanned copies of the
hand signed drawing are permitted as long as the clarity of the drawing is not compromised.
Alternatively, copies may be printed directly from CAD. It is acceptable for these not to contain a copy
of the hand signature, but to bear typed initials instead.
3.4 Units
All general drawing work (e.g. Xrefs) are to be in model space and be produced in meters to three
decimal places. Drawing borders to be in paper space and in millimeters.
e.g. 54.000
78.720
0.325
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 649
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
sDimensions in meters and using whole numbers, can be expressed using the m (meter) suffix as in
the following
45.000m
The position of the decimal point shall be the same as a full stop and no space shall be left between the
number and its units, to ensure clarity, as in the following example:
5.800m
All other non-linear measurements, e.g. areas and volumes, shall be followed by the unit symbol. The
most common non-linear measurements are as follows
2
Square meter - m
3
Cubic meter - m
All detail drawing work (e.g. standard details) is to be in model space and be produced in
millimeters in whole numbers (i.e. no decimal places).
e.g. 10000
787
Dimensions in millimeters using whole numbers, can be expressed using the mm (millimeter)
suffix as in the following
250mm
0+100 (Chainages in whole numbers can be written without the decimal accuracy)
15+255.345
Chainages are plan measurements taken along a setting out line, and provide a horizontal
distance not taking into account slope lengths.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 650
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Drawing sizes shall conform to the International Standards Organisation (ISO). Sizes (in mm)
are as follows: -
A0 1189 x 841
A1 841 x 594
A2 594 x 420
A3 420 x 297
A4 297 x 210
In general, all drawings shall be produced at the preferred A1 original size. The use of
A0 size drawings shall be avoided wherever possible.
Each group or set of drawings shall use only one drawing size unless situations make this impractical.
3.6 Scales
Scales used on drawings shall be selected as indicated in the table below. Only standard metric
scales shall be used. In all cases, the selected scale shall be large enough to permit easy and clear
interpretation of the information depicted.
Specific scale requirements of particular drawings such as layouts will be as stated as per RFP.
Table 8
Permitted scales
In exceptional cases where for functional reasons the recommended scale cannot be applied,
intermediate scales may be chosen, provided that the required scale is of a whole number, such as
1:125, 1:150, etc.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 651
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
ii. CAD entities shall be drawn at full scale (1 Drawing unit = 1 Measurement unit). Final
plotted scale shall be established during composition of the drawing layout for plotting.
iii. Originators using AutoCAD shall employ the PAPER SPACE/MODEL SPACE facility to
establish drawing layout and scales. All drawing entities shall reside in MODEL SPACE with
the exception of view ports, general notes, revision clouding and its labels, title block and
border.
iv. Where different scales exist, each scale shall be specified under the title of the area of the
drawing to which it applies and noted in the Title Block field as shown below:
Figure 16
v. Where a single scale is used on a drawing, it shall be specified within the title block only. (See
the object area and shall be large enough to below). The scales selected shall depend on the
object area and shall be large enough to permit easy and clear interpretation of information
and ensure clarity of prints on the original as well as reduced copies i.e. A3 versions of A1
drawings.
Figure 17
vi. Where different scales are used for horizontal and vertical dimensions, such as in profiles, each
scale shall be clearly indicated on the drawing as shown below:
Figure 18
vii. When the drawing is not drawn to any scale, NTS (Not to Scale) shall be placed in the title
block as shown below:
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 652
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Figure 19
Notes are to be numbered and positioned appropriately and shall include the following notes:
i. All Dimensions are in meters unless otherwise stated. (Only on drawings drawn in meters)
ii. All levels are in meters (Only on drawings where this note is applicable)
iii. All dimensions are in millimeters unless otherwise stated. (Only on drawings drawn in
millimeters)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 653
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Where a General Notes Drawing is used, the first note on each applicable drawing shall contain the
following statement: -
Each area where changes/revisions made since the last issue / submission shall be ringed with a cloud
and marked with an equilateral triangle containing the current revision letter.
Revision clouds and its triangle label shall be placed on the paper space. Arc length of
cloud shall be 15 as a general rule to maintain consistency.
Revision clouds shall be 1.0mm thick (gray or colour 252) and triangles shall be placed on layer
REV.
Clouding and revision triangles denoting the previous revision shall be removed from the CAD file.
Figure 21
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 654
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Note:
As drawings move from one stage to another all historical revision history under that stage is to
be removed from the revision history on the title block.
It is imperative that all drawings are subjected to a Quality Assurance and Quality Control
(QA/QC) check and are duly signed and authorised prior to issue.
Any drawing leaving the drawing office shall have been properly checked for presentation,
clarity, accuracy, technical correctness and compliance with the relevant CAD Standard. Refer
to the flow chart overleaf in Figure 22 for an overview of the checking procedure.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 655
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Schedules
Figure 22: Flow diagram showing overview of CAD drawing checking procedure
INITIAL DRAFTING
NO ACTION REQUIRED
ACTION REQUIRED
ENGINEERING CHECKING
ACTION REQUIRED
CREAT PDF
(WHEN REQUIRED) ETRANSMIT CAD FILE
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 656
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
The Drafting Check will normally be carried out by a person designated by the CAD Office
representative/Manager.
The Drafting Check shall verify adherence to the Project Brief in conjunction with any
applicable supplied criteria. The checker shall also make an assessment with respect to
presentation, standard of workmanship and adherence to the CAD Standard Manual.
The Drafting Check shall, where deemed necessary, include an electronic check of the CAD
File to ensure compliance with applicable standards and/or client requirements.
The check print shall be clearly marked by the checker with any required modifications.
Upon completion of the Drafting Check the checker shall then sign, date and highlight the
required action to be taken.
Any amendment to the drawing requirements may, if required, be carried out prior to the
Engineering Check and a new print raised, duly stamped and signed.
The Engineering check shall verify adherence to the design calculations, design standards and
associated construction issues.
Upon completion of the Engineering Check, the checker shall then sign, date and highlight the
required action to be taken.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 657
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Where required, further check prints shall be raised and the checks repeated.
3.12.5 Approval
Upon completion of the checking process, a clean print of the drawing shall be submitted
to the relevant checkers for signature and to the designated authority for approval. This then
becomes the controlled drawing for reference. The checkers and approvers initials together
with the relevant dates shall be entered in the appropriate areas of the CAD file.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 658
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
iv. The plotted appearance of line types shall be consistent across all drawings.
v. Modification of AutoCAD default source file is not permitted.
vi. Lines on a drawing that cannot be represented by those in the default AutoCAD source
file may be loaded from the approved Custom line types provided.
4.2.2 Line Weights
Table 10
Display Plotted Line
Colour No. Plotted Colour
Screen Color Weight
( ) SBIA_COL_ SBIA_BW
A1.CTB _A1.CTB
1 RED 0.18 BLACK BLACK
2 Yellow 0.25 BLACK BLACK
3 Green 0.35 BLACK BLACK
4 Cyan 0.50 BLACK BLACK
5 Blue 0.70 BLACK BLACK
6 Magenta 0.35 BLACK BLACK
7 White 0.25 BLACK BLACK
8 Dark Grey 0.20 Object Colour BLACK
9 Light Grey 0.15 Object Colour BLACK
10 Object Colour 0.6 Object Colour BLACK
11-79 & 81-249 Object Colour 0.35 Object Colour BLACK
80 Object Colour 0.6 Object Colour BLACK
250-255 (Greys) Object Colour 0.15 Object
Object Colour
Colour
4.3 Text
4.3.1 General
i. The AutoCAD Styles shall have a default height setting = 0.
ii. Sloping, italic, and elaborate fonts are not permitted.
iii. The objective shall be to make all lettering highly legible so that information can be
communicated with the minimal possibility of error in reading. Lettering sizes shall be
chosen such that it shall remain legible when drawings are reduced to A3 size.
iv. Lettering shall be consistent, both in size and placement. Lettering sizes for specific
applications, such as notes or titles, shall not vary within the same drawing.
v. Lettering shall be uniform, clear, sharp and distinct. The mixing of lettering styles, sloping,
italic, and elaborate fonts shall not be permitted.
vi. All text shall be regularly spaced, upright and uppercase and not be underlined.
Deviation: Titles under plans, details etc. are to be underlined.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 659
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
vii. All text shall be left justified. Deviation: Titles shall be centre justified and underlined.
viii. Specific notations shall be carefully placed so they relate to the portion of the drawing or detail
to which they apply.
ix. The placing of notes through drawing lines is to be avoided.
x. Leader arrows relating to specific text or annotation shall be placed in model space with the
detail it is referencing on the same layer as the text to which it relates.
4.3.2 Fonts
Permitted text fonts are as shown below:
Table 11
AutoCAD Style Name AutoCAD Font File CAD Usage
ISOCP ISOCP.SHX Technical/Engineering drawings
ARIAL ARIAL.TTF Presentation Drawings
The preferred text height for general text and notes is 2.5mm.
ii. The text height adopted for a project shall be consistent across all drawings unless
situations make this impractical.
4.4 Dimensioning
Automated dimensioning commands within CAD software programs shall be used for creation and
editing of dimensions, as shown in table 16 below.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 660
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
The editing of dimension values via basic text editing commands is not permitted. Dimensions shall
be associative and placed on their own unique layer.
Table 13
All blocks that need to be created as new blocks shall have all their elements saved on layer 0.
4.6 Hatching
Wherever possible, all hatching created shall be associative and placed on its own unique layer.
Exploding of hatches must be avoided.
4.7 Colours
In AutoCAD, entity colour shall be assigned By Layer. Deviation can be on standard
blocks, i.e. are Road signs blocks where specific standard colours are assigned for each.
4.8 Layering
CAD Layering shall be in accordance with PMNC AutoCAD Layering Standards as included in
Appendix A of this document.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 661
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Additional layers may be required and the naming of such layers must be in the same format in
accordance with PMNC AutoCAD Layering Standards as shown in Section
1 2 3
RD_EX_CNRL
Where:
1 = Department Designator
2 = Status / Section Designator
3 = Feature / Entity Designator
This code identifies the PMNC Department (i.e. B = Building Affairs, D = Drainage
Affairs and RD = Roads Affairs.)
Status / Section Designator (Field 2)
This code identifies the main classification of the type of element within a discipline. For example
EX_SEW describes as existing sewer.
This code further identifies the entity description feature name. For example ABD
describes as the abandoned sewerage network.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 662
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
ii. All reference files are to be inserted in model space with the UCS set to world. All files are to
be inserted at 0,0,0.
iii. Unused reference files shall be detached upon completion of drawings.
iv. The number of reference files on a project shall be kept to a minimum.
v. The preferred method of attaching Drefs shall be Overlay option.
vi. Reference files shall be inserted on unique layer that does not conflict with the general content
of the drawing. (i.e. layer Z_DREF in AutoCAD).
vii. Reference files shall be CLIPPED within the Active drawing sheet file to ensure that only the
design data relevant to the drawing is displayed.
viii. Ref erence files issued externally or shared between departments shall indicate revised areas
with a revision cloud and triangle. A revision history shall be maintained within the reference
file. In AutoCAD, the revision history log shall be placed in paper space, see Figure 29 below.
ix. For Model File Naming refer to Section 3.2
4.10 Plotting
The following standard colour source files shall be used:
Table 14
Aarvee-SBIA--COL_A1.CTB Aarvee-SBIA-BW_A1.CTB
This standard colour source file shall be flexible and can be adjusted to suit users need during
plotting. When drawing files are required, CTB file used for the plotting of the drawing must also be
submitted.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 663
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
4.11.1 Submission
Refer to Programme Management Information System (PMIS) and Document.
Management procedures on submission of drawing.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 664
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 665
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
GIS LAYERS
Screen Plotted L i n e
Layer Name Line type Description
Colour weight
ACAD_ISO13W10
LAND AQUISITION
GIS_ACQ_BDRY 20 0 0.25
BOUNDARY
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 666
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
GIS LAYERS
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 667
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 668
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Plotted
Screen Line
Layer Name Line type Description
Colour weight
EXISTING SURFACE GROUND
WATER
D_EX_SGW 96 SGW_EX 0.35
LINES
EXISTING SGW ATTRIBUTES (ID,
Continuous Diameter,
D_EX_SGW_ATT white 0.25
Length, Material etc)
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 669
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Plotted
Screen Line
Layer Name Line type Description
Colour weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 670
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
DESIGN RECYCLED
WATER
RW_DE_RWPM Green Continuous 0.35 FEATURE: RECYCLED WATER
PUMPING MAIN
DESIGN RECYCLED
WATER
RW_DE_RWDIST Green Continuous 0.025 FEATURE: RECYCLED
WATER DISTRIBUTION
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 671
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
DESIGN RECYCLED
WATER
0.025
RW_DE_RWPS Green Continuous FEATURE: RECYCLED WATER
PUMPING STATION
DESIGN RECYCLED
WATER
0.025
RW_DE_RWRES Green Continuous FEATURE: RECYCLED
WATER RESERVOIR
DESIGN RECYCLED
WATER
0.025
RW_DE_RWVCH Green Continuous FEATURE: RECYCLED WATER
VALVE CHAMBER
DESIGN RECYCLED
0.025 WATER
RW_DE_RWFIT Green Continuous FEATURE: RECYCLED WATER
FITTINGS
PROPOSED ROAD
Screen Plotted
Layer Name Line type Description
Colour Line weight
PROPOSED ROAD
Screen Plotted
Layer Name Line type Description
Colour Line weight
DESIGN ROAD
FEATURE:
RD_DE_CILND green Continuous 0.35
ENTRAL/ROUNDABOUT ISLAND
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 672
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
PROPOSED ROAD
Screen Plotted
Layer Name Line type Description
Colour Line weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 673
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
PROPOSED ROAD
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 674
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
EXISTING ROAD
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
EXISTING ROAD
FEATURE:
RD_EX_CILND green Continuous 0.35
ENTRAL/ROUNDABOUT ISLAND
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 675
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
EXISTING ROAD
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
EXISTING ROAD
FEATURE:
RD_EX_EMBK yellow Continuous 0.25
EMBANKMENT
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 676
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
EXISTING ROAD
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 677
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Screen Plotted
Layer Name Line type Description
Colour Line weight
Screen Plotted
Layer Name Line type Description
Colour Line weight
STREET LIGHTING
RD_DE_ST_TEXT white Continuous 0.25
ANNOTATION/TEXT
Screen Plotted
Layer Name Line type Description
Colour Line weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 678
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
STREET LIGHTING
RD_EX_ST_SUBSTN cyan Continuous 0.5
SUBSTATION
STREET LIGHTING
RD_EX_ST_TEXT white Continuous 0.25
ANNOTATION/TEXT
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 679
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
ROAD/STREET FURNITURE:
Continuous
RD_F_BNCH yellow 0.25 BENCH/SEAT
ROAD/STREET FURNITURE:
RD_F_LGHT white Continuous 0.25
LIGHTING
ROAD/STREET FURNITURE:
Continuous
RD_F_TEXT white 0.25 ANNOTATION/TEXT
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 680
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
RD_C_PROF_GRID_MAJ
Continuous PROFILE GRIDLINE @ MAJOR
R 8 0.2
STATIONS
RD_C_PROF_GRID_MIN
Continuous PROFILE GRIDLINE @ MINOR
OR 9 0.15
STATIONS
SURVEY ROAD FEATURE : SPOT
yellow Continuous HEIGHT
RD_C_SPT_HGT 0.25
MARKER && TEXT
SURVEY ROAD FEATURE :
yellow Continuous SURVEY
RD_C_SPT_NUM 0.25
POINT NUMBER
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 681
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
STRUCTURES
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 682
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
(ELECTRICITY)
Screen Plotted
Layer Name Line type Description
Colour Line weight
SERVICES FIXTURES
Continuous
SVE_ABDL 13 0.35 (ELECTRICITY) : ABANDONED
LINE
SERVICES FIXTURES
Continuous
SVE_DUCT 10 0.35 (ELECTRICITY) : ELECTRICITY
C
SERVICES FIXTURES
Continuous
SVE_ERTH_PIT 8 0.2 (ELECTRICITY) : EARTH PIT
SERVICES FIXTURES
Continuous
SVE_FT_TEE 30 0.35 (ELECTRICITY) : ELECTRICAL
FITTING TEEFIXTURES
SERVICES
Continuous
SVE_LOWV 220 0.35 (ELECTRICITY) : LOW VOLTAGE
SERVICES FIXTURES
Continuous
SVE_MEDV 150 0.35 (ELECTRICITY) : MEDIUM
VOLTAGE
SERVICES FIXTURES
white Continuous 0.25
SVE_MHLL (ELECTRICITY) : UTILITY/MANHOLE
SERVICES FIXTURES
white Continuous 0.25
SVE_MNHL (ELECTRICITY) : MANHOLE
SERVICES FIXTURES
white Continuous 0.25
SVE_MRKR (ELECTRICITY) : MARKER
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 683
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
ELECTRICITY
Plotted
Screen
Layer Name Line type Line Description
Colour
weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 684
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
A.4.2 Water
WATER
Plotted
Screen Line
Layer Name Line type Description
Colour weight
SERVICES FIXTURES (WATER) :
Continuous 0.35
SVW_ABDL 13 ABANDONED
WATER LINE
SVW_BNDL 130 Continuous 0.35 SERVICES FIXTURES (WATER) : BUND
WATER
Plotted
Screen Line
Layer Name Line type Description
Colour weight
AREA
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 685
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
WATER
Plotted
Screen Line
Layer Name Line type Description
Colour weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 686
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
A.4.3 Commercial
COMMERCIAL
Plotted
Layer Screen
Line type Line Description
Name Colour
weight
COMMERCIAL
Plotted
Layer Screen
Line type Line Description
Name Colour
weight
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 687
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 688
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 689
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Scale of Factor
Text Height
Drawing (Multiply)
0.25 Pen 0.35 Pen 0.5 Pen
1 : 1000 1.00 2.5 3.5 5
1 : 1250 1.25 3.125 4.375 6.25
1 : 2500 2.50 6.25 8.75 12.5
1 : 5000 5 12.5 17.5 25
1 : 10000 10 25 35 50
1 : 25000 25 62.5 87.5 125
Scale of Factor
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 690
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Scale of Factor
Drawing (Multiply) Text Height
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 691
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 692
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 693
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 694
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 695
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 696
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Aurangabad Industrial Township Limited EPC Agreement
The Contractor shall provide a General and Administrative HSE Procedures that will engage the
welfare of labor, staff and others abiding by the rules and regulations and provide for records to the
Employer's Engineer.
The Contractor shall prepare specific HSE plans based on the specific construction procedures to be
adopted specifically for this project to address complexity, safety and welfare of labor/staff/equipment
as per the details given below.
Contents
1. HSE Standards
2. Legislation
3. HSE Management System
4. HSE Risk Management
5. Hazard identification and control
6. Environmental Management
7. HSE PERSONNEL
8. Competence and Training
9. HSE Orientation Training
10. ID card & Booklet
11. Intervention
12. Medical fitness to work
13. HSE Communications and Meetings
14. HSE Performance Reporting
15. Target and Objective setting
16. HSE Incident Management
17. Emergency Preparedness and Response
18. HSE Audits, Reviews and Inspections
19. HSE Records
20. Sub-Contractor Management
21. Project HSE plan
22. Substance abuse
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 697
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
HSE Standards
The contractor shall ensure that all personnel engaged (including sub-contractors) with the project shall
be conversant with and at all times comply with the HSE standards for the project. The HSE standards
shall include the relevant India HSE legislation, relevant IS (Bureau of Indian Standards) & Project HSE
documents. (documents prepared by the PMNC with regards to HSE). See Annexure-I
1. Legislation
For the purposes of the project relevant Indian HSE legislations shall apply to the project as dictated
by the various Ministries including but not at the least Ministry of Labor & Employment;
Department of Labor Government of Maharashtra; Ministry of Environment, Forest and Climate
Change.
5. HSE Enforcement
The PMNC or its representatives shall have the right at any time to audit or inspect Contractor
facilities, procedures, and safety management systems. The Contractor shall fully co-operate in such
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 698
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
reviews and shall implement recommendations at its own cost where Project HSE Standards or
statutory rules and regulations are contravened. Contractor shall ensure the timely closing out of issues
raised via these HSE assessments.
The PMNC will bring to the attention of Contractor any situation where the PMNC observes, or is
informed of, a contravention of the HSE rules and procedures or unsafe acts; or a situation where
those contraventions or unsafe acts identified are not considered likely to present an immediate risk,
but are likely to lead to injury, ill health or damage to the environment.
If the PMNC observes, or is informed of, a contravention of the safety rules and procedures or unsafe
acts, and if those contraventions or unsafe acts identified are considered likely to present an immediate
risk to personnel, then they shall have the authority to stop such work until remedial actions have been
addressed to prevent such unsafe acts from recurring.
If contraventions or unsafe acts persist or present an imminent risk of serious injury or ill health to the
persons involved, PMNC will have the right to stop work being performed and to order a suspension
of the execution of any new work in that part or parts of the Works affected by Contractors HSE
violation or negligence.
Suspension of work shall be measured from the date of issue of an instruction from PMNC to
Contractor to suspend work on that particular part of the Works until the unacceptable safety violation
has been fully rectified. In such an instance, Contractor shall have no right to claim for any extension
of time or to claim for compensation for the suspension of the work or for the waiving of the
liquidated damages.
Contractor shall not resume provision of the Works affected until the PMNC is satisfied that the non-
compliance has been rectified.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 699
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
6. Environmental Management
The contractor shall specify in their HSE plan measures applied to avoid harm to the
environment.
7. HSE PERSONNEL
The contractor shall ensure that adequate HSE personnel are appointed on the project. No HSE
personnel on the project shall be appointed without prior written permission from PMNC. The
Contractor shall ensure that all HSE personnel meet the requirements as dictated by the project
HSE standards.
8. Competence and Training
The contractor shall ensure that that all personnel are competent, capable and qualified to a level
that allows them to work without creating unnecessary risk for themselves and others. All
personnel shall have and maintain the necessary HSE competencies to perform work on the
project to the required HSE standards.
The contractor shall ensure that all supervisory personnel have formal training in supervisory
activities and specialist HSE training to conduct their duties.
The contractor shall ensure that a project HSE training matrix is produced. The training matrix
shall include the various positions on the project and detail the HSE training that is required for
each position.
9. HSE Orientation Training
The Contractor shall ensure that all personnel working at the project receive an induction HSE
training explaining the nature of the work, the hazards that may be encountered during the site
work and the particular hazards attached to their own function within the operation on the first
day of work on the project. The training shall cover the contents as detailed within the Project
HSE standards.
The contractor shall ensure that any new personnel are informed in an equal manner.
10. ID card & Booklet
The contractor shall ensure that all personnel working on the project (including sub-contractors)
be issued with a photo identity card duly signed by the authorized representative of the contractor
before they are engaged for any work.
The contractor shall also issue a personal HSE handbook in a language known to the workers,
which provides information on HSE and emergency procedures that all working personnel are
required to know and need to follow. Contractor shall ensure that this is distributed and its
content introduced to all personnel working at the site.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 700
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
11. Intervention
The contractor shall have implemented a system that assures competence (including HSE) of
personnel. For those roles where no suitable recognized competence standards exist, the
contractor shall provide, upon the PMNCs request, information on the selection criteria and/or
method used to provide assurance of individual competence.
The contractor shall establish and agree with the PMNC a key list of personnel undertaking
taking HSE critical roles. The list shall identify these key individuals by name and by (key) role.
For every role on this list, the contractor shall define minimum requirements for HSE
competences and qualifications relevant to the work.
The contractor shall minimize turn-over of HSE personnel, where possible, to ensure established
competence levels and to minimize role discontinuity. The contractor shall obtain the PMNCs
written approval prior to replacing any personnel on the list.
The contractor shall have implemented a system that records the training of personnel. The
contractor shall keep training records up-to-date and shall furnish information about the system
and/or records of training upon request by PMNC.
12. Medical fitness to work
The contractor shall ensure that all personnel engaged on the project are medically fit for the job
to be undertaken. Where required, the contractor shall be able to demonstrate that personnel,
selected for key positions are evaluated for their fitness to work on the project.
13. HSE Communications and Meetings
The contractor shall ensure efficient and effective HSE communication and consultation with all
personnel involved on the project. This includes but is not limited to toolbox meetings prior to
the start of work, regular worksite HSE meetings with all parties involved (including
subcontractors).
The contractor shall participate in any HSE meetings as organized by the PMNC.
14. HSE Performance Reporting
The contractor shall submit on a monthly basis an HSE performance report to the PMNC. This
report shall contain as a minimum the following data, as related to the project:
A list, including a brief description, of all incidents (including near misses and potential
incidents);
Number of Fatalities (FAT);
Number of Lost Workday Cases (LWC);
Number of Restricted Workday Cases (RWC);
Number of Medical Treatment Cases (MTC);
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 701
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 702
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 703
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Contents
Section 1 - Project Details
Section 2 - Information and Training for People on Site
Section 3 - Contractor Management Selection of Plant
Section 4 - Emergency Procedures
Section 5 - Arrangements for Controlling Significant site Risks
Section 6 - Environmental Management
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 704
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
This plan is provided as a guidance template for the Contractor to include in their HSE plan. The sections
mentioned in this HSE plan template will be the minimum standards that the Contractors HSE plan will
be assessed against.
Section Titles of
Details of what is required in each section
No sections
Contractor must ensure that these sections are included in their Construction HSE plan.
The details in the sections are provided as guidance.
Details of other Details as above of any consultants that the contractor may
1.2
Consultants employ on the project.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 705
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Project
Contractor to include a detailed organization chart with names,
1.5 Organization
designations & contact numbers for the project.
Chart
1.7 Project Goals Contractor to detail what are the project HSE goals.
1.8 HSE
Contractor to detail how HSE compliance monitoring will be
Compliance
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 706
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
monitoring conducted, who will conduct, how often this will be conducted.
Senior
Contractor to detail how Senior management on the project will
Management
1.9 be involved in HSE monitoring, How often will they be
HSE
involved, what is the process.
monitoring
Site Safety Contractor to detail what site safety rules will be developed or
2.2
Rules is available for the project.
3.2 Selection of Contractor to detail how they will ensure that only safe plant &
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 707
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 708
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 709
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 710
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
1. SECTION 1: INTRODUCTION
This document describes how Health, Safety & Environment (HSE) will be managed on the SBIA
Programme. This document is provided to ensure that the appointed Package Contractor,
Engineers, Consultants and another Stakeholder(s) who are working closely on the SBIA
Programme understand the HSE standards on the programme. This document should be read along
with the SBIA Health Safety Environment Execution Plan (PMC-657466-HSE-S01-PRC-015).
The standards laid down by this document is mandatory for all on the SBIA Programme.
All Package Contractor/Consultants must familiarise themselves with these standards and also
ensure that these standards are adhered to by any subcontractors/suppliers and any self-
employed persons working within their workforce.
These standards will assist the contractor in their planning and provision of satisfactory HSE
resources on projects.
These standards will be audited in accordance with set performance measurement procedures as
per specific audit schedule completed for every project.
Poor or non-compliance with these standards may result in the contractor being removed from
the project.
1.1. Purpose
The purpose of this document is to provide a systematic framework to:
Implement & Manage HSE on the SBIA Programme.
Achieve the overall HSE objectives of the SBIA Programme.
Ensure open and transparent communication of HSE on the SBIA Programme.
1.2. Scope & Applicability
The scope of this document is limited to the SBIA Programme and covers the programme projects,
programme site office, and everyone working on any aspect of the SBIA Programme Delivery. The
Programme Manager for New Cities (PMNC) HSE Manager will review this document every year
as a minimum, ensuring that it keeps abreast with any changes of/on the SBIA Programme.
Stakeholders including Package Contractors are responsible to ensure that they have the latest
version of this document. Copies of any forms and templates mentioned in this document is
available with the PMNC HSE Manager and shall be made available on request.
1.3. Legal and Other Requirements
All parties involved on the SBIA Programme shall comply with all local legislations, Client/SBIA
Programme/ PMNCs HSE requirements. Where legal requirements conflict with those set out in
any other Client/SBIA Programme/ PMNCs HSE document, the more stringent requirement will
apply.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 711
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
All works will be carried out in compliance with the HSE rules, acts & regulations set out by the
following:
The Government of India, Ministry of Labour & Employment (http://labour.gov.in/)
Department of Labour Government of Maharashtra
(https://mahakamgar.maharashtra.gov.in/index.htm)
Ministry of Environment, Forest and Climate Change (http://www.moef.nic.in/)
DMICDC (http://www.dmicdc.com/)
Maharashtra Industrial Development Corporation (http://www.midcindia.org/)
Aurangabad Industrial City (AURIC) (http://www.auric.city/)
Bureau of Indian Standards (http://www.bis.gov.in/index.asp)
Contractually specified international standards and codes of practice
Relevant industry standards and guidelines
Contractual standards, procedures, and work instructions
The PMNC HSE Manager maintains a non-comprehensive HSE legislative list, Package Contractors
are encouraged to refer to this list (as and when required). Alternatively, all HSE legislations
governed by government organizations in India can be accessed in thru their respective websites.
1.4. Programme HSE Aims and Objectives
The PMNC has set specific objectives to achieve the overall SBIA programme vision. Key HSE
objectives include, but are not limited to, the following:
Visible commitment to HSE from leadership on the SBIA programme including Clint, PMNC
& Package Contractor.
Apply robust HSE principles across the SBIA programme.
Apply zero tolerance for HSE violations.
Include HSE as an agenda item at all formal meetings.
Implement HSE best practice initiatives.
Continually learn and improve approaches should accidents and incidents occur.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 712
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Ensure that the arrangements and resources on the SBIA Programme are adequate and reviewed
as necessary.
Maintain a reporting structure for HSE matters and ensure that reporting lines and
responsibilities of line management are clearly defined.
Attend or support appropriate HSE management or steering groups as necessary.
Ensure that HSE is the first agenda point of all meetings
Ensure that resources are available to maintain an effective HSE performance, including
budgetary, suitably trained staff and competent staff with clear lines of command and
responsibility.
Carry out HSE tours on a regularly defined basis.
Be aware of the principles of the current HSE legislation and developments and ensure that
their staffs are aware of their accountability for HSE.
Ensure that all accidents and incidents reported on the SBIA Programme are fully investigated
and actions closed out.
Ensure that appropriate support has been offered to those affected by incidents.
All Contractor Senior Management will lead by example.
2.1.2. Contractor Line Management Responsibilities
Be aware of the HSE requirements of applicable to the SBIA Programme.
Ensure that during planning, construction and production, maintenance and repair, sufficient
allowance is made for safe systems of work, adequate welfare facilities & supervision.
Ensure that the management team is adequately staffed with suitably trained and experienced
personnel with clearly understood and defined responsibilities that allow for close and effective
supervision of operations.
Ensure that a competent staff member will be present at all times when work is being
undertaken under their control.
Liaise with their HSE team on SBIA Programme HSE requirements.
Ensure that they understand the requirements of the SBIA Programme HSE Plans & Procedures
and that the plan is communicated and implemented effectively on site.
Ensure that safety critical appointments are made in writing and persons appointed are suitable
for the role.
Arrange/chair/attend the site HSE meetings.
Ensure that overall and specific risk assessments & method statements are produced, submitted
and communicated to relevant parties on time.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 713
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 714
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Prevent horseplay and discipline those who consistently fail to consider their own wellbeing
and that of others around them.
Report all accidents/incidents/near- misses to the site HSE department.
All Contractor supervisors must set a personal example
2.1.4. Responsibilities of workforce
Take all reasonable care to ensure your own safety and that of any others who may be affected
by your work.
Attend the site induction, tool box talks and other HSE communications as required by the
project.
Avoid improvisations or deviations from approved method statements & risk assessments.
Use the specified tools and equipment for the job.
Take personal responsibility for your actions.
3. Section 3: Planning
3.1. Package Contractor HSE Plan
Package Contractors shall prepare a HSE Plan that shall define their HSE intend and how they plan
to manage HSE on the SBIA Programme. The HSE plan shall not only take into consideration all
the activities that the Package Contractor will undertake, but shall also consider any interface with
governmental agencies, other package contractors, area locals etc. The HSE Plan shall be submitted
to the PMNC for review & comments at least one month prior to mobilization.
The Package Contractor shall review and amend their HSE Plan, as conditions related to the SBIA
Programme/Project Site (s) or the works change, but as a minimum, the HSE plan shall be revised
and resubmitted to the PMNC on a yearly basis. Package Contractors shall not commence any
construction activities until its HSE Plan has been reviewed & commented upon by the PMNC.
The Package Contractor shall take, or cause to be taken, any additional measures, which the
Governmental/Client/PMNC may direct to protect against injury or death of any person or damage
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 715
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
to or loss of any property or to the environment during/after the Package Contractors performance
of the works.
Submittal of any documentation to the Client or PMNC does not relinquish the Package Contractor
of its direct responsibility for the HSE of persons and the protection of the environment.
3.3. Project HSE Risk Assessment
Before commencement of an onsite project work, the Package Contractor shall ensure that a robust
Project HSE Risk Assessment of the works to be undertaken is conducted. The Project HSE Risk
Assessment shall be a systematic assessment of the HSE hazards & risks that the Package Contractor
could encounter and shall also detail the means to control these. The Package Contractor shall ensure
that a copy of the Project Risk Assessment is submitted to the PMNC for review and comments.
The Package Contractor will be expected to recognize HSE hazards, evaluate them with the help of
competent people, and to communicate to workers on how to control these hazards during the
execution of the works.
The Package Contractor will be expected to use different types of hazard analyses to ensure that
work progresses in a manner that does not endanger persons, property, process and the
environment. Examples of these include:
Phase Hazard Analysis;
Emergency Procedures;
Job/Task Hazard Analysis;
HAZIDs;
Critical Task Analysis;
Field Level / Daily Risk Assessment;
Behavioral Based Safety.
The Contractor shall review the Project HSE Risk Assessment upon any change in the scope of work
and/or at predetermined intervals during the execution of works.
3.4. Aspects & Impacts Register
The Package Contractor shall develop an HSE Aspects and Impacts Register that is relevant to the
construction activities and based on their specific construction method statements and the location
/sensitivity of their works. The Package Contractor in his HSE Aspects and Impacts Register shall
identify any significant HSE impact that could result from his works, ensure adequate control
measures are in place and that the residual risks are acceptable.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 716
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Package Contractor shall ensure that the Aspects & Impacts Register is regularly updated and
copies submitted to the PMNC for review and comments.
3.5. Readiness Review Go/No-Go
The HSE Readiness Review is a meeting among key PMNC and the Package Contractors personnel
and functional support to confirm that all necessary planning and actions have been addressed enable
the successful execution of the works. The HSE Readiness Review serves as a management tool in
determining the readiness or preparedness of the Package Contractors team to mobilize/execute the
works/activity. This is an important activity because it is used to identify gaps in the Package
Contractors preparatory activities that could result in failure of the works. The review shall highlight
the deficiencies, and focuses the delivery team on correcting those deficiencies.
The Package Contractor shall be responsible to conduct this HSE Readiness Review and invite the
PMNC key staff. Additional reviews may be required if deemed necessary by the PMNC at various
project phases or project milestones.
The HSE review should be conducted by the Package Contractor at least two weeks prior to
mobilizing personnel to the field and at each critical project task/milestone/activity. All Package
Contractors shall demonstrate that they are ready to execute their activities in the safest manner. The
following documents, as a minimum, shall be checked during the review:
Related procedures or plans of the Contractor;
Method statements;
Risk assessments;
Internal and external permits for the activity (if necessary);
Competency approval documents (personnel certificates such as welder, operator, etc.);
Training records;
Site layout;
Medical fitness records of employees; and
Driver permits.
If the Package Contractor fails to demonstrate readiness to the satisfaction of the PMNC
the relevant activity shall not commence.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 717
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Package Contractor shall ensure that no work is started on site without an approved &
agreed Method Statement.
4.2. Hazard Identification & Risk Assessment
The Package Contractor shall ensure that a Hazard Identification & Risk Assessment (HIRA) is
available before any works are executed on the site. The Package Contractor shall also ensure that
the HIRA shall be attached to the method statement and both documents shall be referred to as a
source of safe work methods. The HIRA shall not be the sole responsibility of the Package
Contractor HSE team but shall be produced/documented with the Package Contractor construction
team in lead.
The Package Contractor shall ensure that the four basic stages in conducting a HIRA are considered:
selecting the task to be analyzed
breaking the task down into a sequence of steps
identifying potential hazards
determining preventive measures to overcome these hazards
The Package Contractor shall review the HIRA upon any change in the scope of work and/or at
predetermined intervals during the project. A copy of the HIRA shall also be made available on site at
the time of an HSE inspection (as required).
All HIRAs will be submitted to the PMNC for review & comments at least 3 weeks prior to a task
starting on site.
The Package Contractor shall ensure that no work is started on site without an approved &
agreed HIRA.
4.3. Permit to work
Where the risks are high and the use of a method statement and risk assessment alone does not
necessarily ensure that a safe system of work is followed, the Package Contractor shall ensure that a
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 718
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
permit to work is implemented. As a minimum, Package Contractors shall ensure that the following
works are controlled by a permit to work:
Permit-to-Dig Demolition Permit
Hot Works Permit Confined Space Permit
Electrical and Mechanical Permit/LOTO General permit to work
The need for a permit to work system will be identified in the risk assessment for the activity.
Examples of jobs that are typically covered under a permit shall include but not be limited to hot works
(cutting, grinding, welding etc.), elevated works (anything above 4 meters), confined space entry, work
on electrical systems, non-routine lifts.
Package Contractors shall ensure that they nominate a person as the permit coordinator who shall
have the responsibility to oversee the permit to work procedure. All permits shall be valid for a
single shift only. Records of any permits issued shall be kept in the permit coordinators office for
further inspection.
4.4. Personal Protective Equipment
The Package Contractor shall ensure that Personal Protective Equipment (PPE) is provided as
identified in the Method Statements & Risk Assessments. Notwithstanding the PPE described in the
Method Statements & Risk Assessments, the Package Contractor shall ensure that as a minimum
standard Safety Helmet, Hi-Viz Jackets, Safety Goggles, and Safety Shoes (with penetration
protection) is available to all undertaking works on the project.
All PPE supplied on the project shall meet or exceed the specifications as dictated by Indian
Standards Institute or the Contract documents. Where there is a conflict the more stringent
standard shall apply.
5. Section 5: Training, Awareness & Competence
All project employees must receive appropriate HSE training upon engagement. These trainings
shall be delivered by the individual Package Contractors to their personnel and to any
subcontractor/third party engaged by them. HSE trainings will include - Induction Training, Tool
Box Talks (TBTs), Work/Topic specific training, which will be determined by the
Programme/Project HSE Training Matrix, and will be dependent on the tasks scheduled to be
performed.
5.1. Minimum Requirements
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 719
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Package Contractor shall ensure that all their personnel (including sub-contractors & any third
party contracted to them) complete the following fundamental trainings:
New Project HSE Induction this module will orient employees in the basic HSE Policies and
Procedures relevant at the project.
Position specific HSE training this will include training that depends upon the position the
individual holds on the project. For example, if the person is designated as a rigger, he will
have to attend rigger training and a slinging & lifting training. These trainings can be
conducted either in-house by the individual Package contractors or by an Approved Third
Party. The Package Contractor shall also be aware that Project employees may be required to
complete additional specialized HSE training, provided by commercial training specialists.
Such training shall be identified in the project training matrix.
Tool Box Talks These will be conducted on daily/weekly basis as dictated by the
activities/tasks that groups of people are undertaking.
The Package Contractor shall ensure that all HSE training conducted on the SBIA programme is
documented and tracked.
5.2. Project HSE Induction
The Package Contractor shall conduct an HSE Induction for all project employees (this shall include
all personnel employed by the contractor, their sub-contractors, Third Party, Visitors etc.) so that
they remain aware of appropriate precautions that apply to them whilst on the work site. This HSE
induction shall be conducted prior to being authorization to enter the site and/or commencing work.
As a minimum, this training shall include a presentation of the site hazards, safety and security rules
and emergency procedures. Depending on the appreciation of the level of risk for the contracted
work, other relevant HSE subjects will be presented.
The site HSE induction shall be conducted by the Individual Package Contractor HSE Manager and
shall be conducted in a language understood by the site personnel. All Package Contractors shall
ensure that their Project HSE Induction training is submitted to the PMNC for review and
approval.
As the project progresses, the Project HSE induction shall be reviewed by the Package Contractor
HSE Manager at regular intervals to reflect site conditions.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 720
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Package Contractor shall ensure that daily/weekly toolbox meetings and other daily briefings
are conducted on a regular basis. These where possible shall be conducted by the foreman and site
in-charge.
5.4. Emergency Response Plan Training
The Package Contractor shall ensure that all project employees are aware of the Project Emergency
Response Plan. The Package Contractor shall ensure that training to familiarize project employees
on the Project emergency response plans is conducted at regular intervals of not less than 6 months.
The Project emergency response plan training will include the procedures for reporting to external
emergency response organizations (e.g., police, fire department, ambulance services, hospitals,
rescue services, and hazardous material response services), building or site evacuation, designated
evacuation assembly areas, and methods of accounting for staff upon evacuation. Emergency drills
will be performed periodically, but at least twice per year.
The table below gives an overview of the HSE communication methods that the Package Contractor
shall adopt on the project.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 721
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Method Frequency
The Package Contractor shall invite the PMNC representatives to attend all meetings and shall
provide copies of HSE meeting minutes. The Package Contractor shall keep records of all matters
discussed and decisions made at each meeting, records of Site inspections performed, register of
work permits issued, records of attendance of participants, etc.
The Package Contractor shall ensure that Construction Manager shall attend these meetings.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 722
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
7. Section 7: Monitoring
7.1. HSE Inspections
The Package Contractor shall carry out HSE inspections at regular intervals, covering not only
its works on the project but also other areas under their control such as camps/mess facilities.
These HSE inspections shall be led by the Package Contractor HSE team but shall also be
attended by the Package Contractor Construction team. The Package Contractor shall ensure
that Project HSE Inspections are carried out at least once a week. Inspections of other areas
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 723
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
such as campsites/mess areas shall be carried out at a suitable frequency and agreed with the
PMNC. Where necessary, the PMNC representatives will join these inspections.
The Package Contractor shall ensure that inspections of temporary works such as shoring of form
work, excavation, trenches, cranes and scaffolds shall be carried out after inclement weather.
Copies of such inspections reports shall be submitted to the PMNC for review & comments.
The Package Contractor shall appoint an independent appropriately qualified external auditor to
audit the Package Contractors compliance with its HSE Plan and HSE management systems of the
Works at least once every twelve (12) months. In addition, the Package Contractor shall carry out
internal safety audits to verify whether safety activities comply with the HSE Plan and the HSE
management systems. Where it is deemed necessary, the PMNC shall be entitled to engage an
independent external auditor at the Package Contractors cost to audit the Package Contractors HSE
Management System.
7.4. HSE Observation Program
The Package Contractor will encourage and educate the project staff to observe and identify safe and
at-risk conditions and behaviors. Staff are also encouraged to report near misses in order to look for
trends and tackle issues before accidents and incidents occur.
7.5. Reporting Unsafe Conditions
All personnel on the SBIA Programme must report any situation, practice, or condition which might
jeopardize the safety of the projects. All unsafe conditions or unsafe practices will be corrected
immediately. The SBIA Programme will have zero tolerance of unsafe conditions or unsafe
practices.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 724
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Package Contractors shall ensure that all accident/incident reports are submitted to the PMNC within
an agreed timeframe. This time frame shall be agreed with the PMNC HSE Manager.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 725
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
For the purpose of reporting, on the SBIA Programme the following definitions shall be adopted by
all Package Contractors:
Lost Time Injury: Any accident/incident that results in an employee not being able to work on
the day following the accident.
Medical Treatment Case: Any work related accident/incident where the employee has to
receive medical treatment in a facility outside project first aid. This can be a clinic or hospital.
First Aid Case: A minor work related injury that requires the person to seek medical attention
at the project first aid clinic.
Near Miss: An unplanned event or condition that occurred in the project which although didnt
not result in an injury or damage property but had the potential to do so.
Major Accident/Incident/Near-Miss: Categorized / defined as one which meets or exceeds the
following consequences:-
o Harm to People: Major injury or health effects (including permanent disability) - Affecting
work performance; on longer term, e.g. prolonged absence from work. - Irreversible health
damages without loss of life, e.g. noise induced hearing loss, chronic back injuries.
o Property Damage: Damage to any Project property in excess of INR 50000.00 or will take more
than 2 days of to rectify.
o Environmental Effect: Any damage to the environment which costs an upwards of INR
50000.00 to clean up.
o Work Related: Any injury (however small) that has happened to a personnel whilst he was
working on the project site.
8.3. Report Documentation
The Package Contractor shall ensure that the accident/incident report that is submitted to the PMNC
as a minimum will have the following described details/sections.
Details of the investigation Team: List of investigation team members
Background of the Incident: The environment of the accident before the accident occurred
The Incident: Detailed description of what happened in detail, the actions taken by the
Package Contractor.
Immediate Cause: Direct and indirect causes of the incident.
Root Cause: Complete root cause analysis of what caused the incident/accident.
Investigation Findings: Sketch of the incident scene, photographs, diagrams and physical
evidence, persons with information and statements
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 726
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 727
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
When planning ERPs, the Package Contractor shall ensure that the following shall be taken into
account:
Site size, characteristics of the site and the work being undertaken;
Means of raising the alarm under those conditions;
Plant and equipment to be used in the event of an emergency;
Location of nearest emergency services and their capabilities;
Access to the site for emergency services.
The ERPs developed by the Package Contractor shall be specific to the Package Contractors work
package. Topics to be addressed in the plan shall include, but are not necessarily limited to the
following:
A list of all key emergency response personnel on site showing responsibilities and contact
details, including all-hours telephone numbers;
Details of emergency services (police, fire, ambulance, spill clean-up etc.);
Communications strategy, including liaison with emergency services and the PNMCs
representative;
Emergency provisions on site, including fire prevention, detection and fighting systems, spill
prevention and response equipment and first aid facilities;
Protocols and procedures to be implemented in the event of specific emergency situations;
Emergency response training;
The Package Contractor shall ensure that the ERPs are submitted to the PMNC for review and
approval within 2 weeks of mobilization and prior to any works starting on site. The Package
Contractor shall also review and ensure the adequacy of the ERPs as the works progress to
accommodate the changes to the site conditions. The Package Contractor will ensure that all
changes to the ERPs are approved by the PMNC.
9.3. Emergency communication
The Package Contractor shall ensure that the ERP is reviewed at regular not less than every six
months. The Package Contractor shall also bring the contents of the ERP to the attention of the
Project personnel during Project Inductions, Tool Box Talks, Safety talks etc. These briefings shall
as a minimum include:
Emergency procedures for different scenarios;
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 728
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
All incident response resources shall be suitable for the site and activity under consideration.
Equipment, including emergency response PPE, spill kits and firefighting systems, are to be
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 729
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
installed at all locations where high risk activities are being carried out and must be inspected,
tested and maintained regularly by the Package Contractor. If any equipment is missing or
damaged, it shall be replaced.
The Package Contractor is required to develop a specific temporary facilities and welfare plan
detailing specific arrangements. This plan must be submitted to the PMNC for review and approval.
10.1. First Aid Room
The Package Contractor shall make adequate arrangements for a first aid room, equipped and staffed
to the extent required. The first aid room as a minimum meet the requirements below but in any case
will meet any requirements as laid down by local regulations.
Designated first aid room shall not be used for any other purpose other than for first aid or
medical purposes;
The room shall be identified clearly through first aid signage;
It shall be located in a way to allow easy access and egress during emergency;
Shall be spacious enough to accommodate a wheel chair or a stretcher;
Shall be equipped with adequate facilities and equipment, well illuminated, ventilated,
sufficient air conditioning and made up of a surface that is easy to clean;
Arrangements exist for the disposal of refuse;
Shall be clearly identified in the emergency plan / layout;
Shall be equipped with a phone or other means of communication to contact ambulance
/hospital/ doctor on call/Company representatives.
10.2. First Aid Box
The Package Contractor shall depending upon the size and location of the site, ensure that first aid
boxes are provided at strategic locations & shall be suitably identifiable, and access to them shall be
ensured throughout the working hours. The Package Contractor shall also regularly inspect these
first aid boxes to ensure that it is fully stocked and items inside are not expired. Records of such
inspections shall be maintained and produced to the PMNC during HSE inspections (as required).
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 730
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Names of the qualified first aid personnel shall be exhibited near the first aid box and other
prominent locations on the project and site offices with immediate contact details.
10.4. Nurse/Doctor on call
The Package Contractor shall make appropriate arrangements to attend to the emergency medical
situations through the appointment of a male/female nurse/Doctor onsite (as required contractually).
Alternatively, the Package Contractor shall ensure that provision is made to ensure that medical
assistance is given to any injured person as quickly as possible through a contractual arrangement
that may be made with a clinic / approved hospital.
The name/information about the hospital shall be exhibited at prominent locations within the project/
site offices and shall be bought to the attention of the project personnel at the time of the induction.
10.5. First Aid Treatment Records
Records of the first aid containing the details of the treatment given, name of the treated person, date
and time of accident, place and circumstances, details of injury and treatment given and name of
person rendering treatment shall be maintained by the Package Contractor and provided to the
PMNC (during HSE inspections as required).
10.6. Canteen/Mess
The Package Contractor shall make adequate arrangements to ensure that project personnel can
consume food in a clean & hygienic environment. Canteen/mess facilities shall be established at the
site for providing food and beverages to the project personnel. Food may be prepared at the site or
pre prepared food may be made available.
The Package Contractor shall ensure that eating areas are suitable for the project personnel using
them. For example if the local culture is to consume food whilst sitting on the floor, then the
canteen/mess facility shall ensure that there is provision for project personnel to sit on the floor. The
canteen/mess facility shall be adequate for the number of personnel and shall accommodate all users.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 731
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Package Contractor shall consider the following when setting up a canteen:
10.9. Toilets
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 732
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Package Contractor shall ensure that toilets are provided to for the project employees.
Consideration shall be given to male & female toilets (where required). These toilets shall be
constructed of solid material which can be washed, is weather proof and must provide adequate
privacy. The toilet facilities shall have adequate ventilation such that foul smells do not travel onto
nearby work areas. The following rate of provision shall be considered:
Male: 1 WC and 1 wash basin per 10 men (up to 100)
However where urinal are provided 1 WC per 25 men (up to 100) and 1 urinal and 1 wash basin
per 10 men (up to 100)
Female: 1 WC and 1 wash basin per 10 women (up to 100)
10.10. Water Tanks
The Package Contractor shall ensure that all water storage tanks are cleaned on a regular basis. The
Package Contractor shall ensure that all portable water tanks are cleaned once every three (3)
months as a minimum and that the water quality is tested and deemed fit for consumption.
11. Section 11: HSE Enforcement
The Package Contractor is fully responsible to ensure that they comply with all the HSE legislations
& contractual HSE requirements. However, the PMNC have the right at any time to audit/inspect
the Package Contractors facilities, procedures and safety management systems. The Package
Contractor shall fully co-operate in such reviews and shall implement recommendations at its own
cost where the PMNC or statutory rules and regulations are contravened. The Package Contractor
shall ensure the timely closing out of issues raised via these HSE assessments.
In addition to enforcement requirements stated in legislation and contract requirements, The PMNC
will have the advice the Package Contractor to remove from the project of any person who, in the
opinion of PMNC, fails to observe HSE procedures. The Package Contractor shall ensure that any
persons who have been asked to be removed from the project on HSE grounds is not employed
without the written approval from the PMNC.
Where the PMNC observes or is informed of a contravention of the HSE rules/procedures or unsafe
acts and if those contraventions/unsafe acts identified are not considered likely to present an
immediate risk, but are likely to lead to injury or ill health, the PMNC shall bring these to the
attention of Package Contractor.
Where the PMNC observe or is informed of a contravention of the safety rules/procedures or unsafe
acts and if those contraventions/unsafe acts identified are considered likely to present an immediate
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 733
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
risk to Personnel then the PMNC shall have the authority to stop such work until remedial actions
have been addressed to prevent such unsafe acts from recurring. If contraventions/unsafe acts persist
or present an imminent risk of serious injury or ill health to the persons involved, the PMNC shall
have the right to stop the work from being performed. In such case, the Package Contractor shall be
responsible to take any remedial action at his own time and cost and shall no right to claim for any
extension of time or to claim for compensation for the suspension of the work or for the waiving of
the liquidated damages. Suspension of work will be measured from the date of issue of an
instruction from the PMNC to the Package Contractor to suspend work on that particular part of the
Works until the unacceptable safety violation has been fully rectified. In such an instance,
Contractor shall not resume provision of the works affected until the PMNC is satisfied that the HSE
non-compliance has been rectified.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 734
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
1 Digital camera with flash At least 4 mega pixels & 1 camera per
HSE staff
2 Computer (with standard Should be available for use at all times and
configuration) not shared with other departments
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 735
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Operational control procedures and processes are required in cases where it is foreseeable that, in the
absence of such procedures and processes, work activities could be conducted in an unsafe manner,
which could then result in accidents or incidents. The PMNC will continue to develop HSE
procedures and processes that cover all phases of the programme, these will be sent out through the
programme correspondence. Package Contractors are encouraged to contact the PMNC, to ensure
that they have the latest version of any HSE process or procedure.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 736
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 737
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
The Contractor shall perform all the Project Management activities necessary for proper planning,
management and control of the work. Below are the project management requirements which
Contractors needs to comply at different stage of the projects:
2. Participate in monthly project status review meetings and present the project progress update
in the meeting. The frequency of project status review meetings may change based on actual
requirements.
3. Schedule: The Contractor shall submit a Level 3 schedule that covers the full scope of
Contractors work within 30 calendar days of date of appointment. This will be reviewed within
15 calendar days by Employer/PMNC. The Contractor shall incorporate the comments and
resubmit the schedule no later than 15 calendar days after receiving the comments from Employer/
PMNC. Upon approval the level 3 schedule will become the baseline schedule for all the future
monitoring and tracking.
i) Develop and incorporate a detailed Work Breakdown Structure (WBS) for all
project schedules that are submitted.
ii) All schedules shall be created, maintained and submitted to Employer /PMNC in the
latest version of Oracle Primavera P6 or equivalent in an electronic format.
iii) All schedules shall follow the Critical Path Method (CPM) of scheduling and shall
have meaningful and realistic logical ties and relationships between activities.
iv) The use of negative lags is not permitted in the baseline and all other versions of the
schedule.
v) The schedule must contain all the long lead procurement items identified.
vi) Shall exercise reasonableness while assigning constraints in schedule and milestones
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 738
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
vii) Upon approval, the copy of the Baseline schedule will become the first Current
Schedule.
viii) The Current schedule shall be actively updated and maintained by the Contractor every
month.
ix) The updated Primavera P6 or equivalent schedule file should be submitted every month
along with Monthly progress report in electronic format. A pdf copy of the updated
schedule with all activities also needs to be submitted
xi) The contractor should also submit a level 4 schedule within 60 calendar days from
approval of baseline level 3 schedules.
xii) In the level 4 schedule activity durations should be reasonable (typically no more
than 15 days duration except for project management tasks, procurement activities for
long lead items or any other activity that obviously needs to be of longer duration).
4. Cash Flow: Prepare project cash flow at the start of the project. Prepare monthly statements to
show the actual versus plan spending; update the cost periodically
5. Lessons Learned Database: The Contractor shall develop and actively maintain a lessons
learned database on a monthly basis (to be included in the monthly project report) and submit it to
Employer/ PMNC at the end of the project during closeout.
6. Risk Register: Maintain an active risk register addressing the risks and mitigation measures (could
be in excel format) that lists the project risks related to their Scope of Work.
8. Monthly Progress Report: Prepare and submit a monthly progress report (standard format and
template will be provided by Employer /PMNC at a later date). Items 3 to 7 mentioned above shall
be the minimum information that will need to be included in the monthly progress report.
9. For better collaboration, Contractor shall use the Programme and Document Management system
that will be provided by Employer/PMNC at a later date and pay for the cost of procuring licenses
to use the system.
Monthly payments are subject to timely submission of monthly progress report and the
monthly updated electronic schedule file in the required and acceptable format.
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 739
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)
Design and Construction of Administration and Business Centre of (GICC)
Ch l on
Cholera (ABCD) B ildi
EPC basis i Ch l S i lI R i A
Design, Construction & Maintenance of the AURIC Hall Building for Phase -I 740
in Shendra-Bidkin Industrial Area, Aurangabad, Maharashtra State on EPC
Basis (Package - IV)