Altivar 212: Variable Speed Drives For Asynchronous Motors Programming Manual
Altivar 212: Variable Speed Drives For Asynchronous Motors Programming Manual
Programming Manual
09/2011
S1A53838
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical characteristics
of the performance of the products contained herein. This documentation is not intended as a substitute for
and is not to be used for determining suitability or reliability of these products for specific user applications. It
is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and
testing of the products with respect to the relevant specific application or use thereof. Neither Schneider
Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information
contained herein. If you have any suggestions for improvements or amendments or have found errors in this
publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical, including
photocopying, without express written permission of Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when installing and using this
product. For reasons of safety and to help ensure compliance with documented system data, only the
manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must be
followed.
Failure to use Schneider Electric software or approved software with our hardware products may result in
injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
2011 Schneider Electric. All rights reserved.
2 S1A53838 09/2011
Table of Contents
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 1 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Steps for setting-up the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Factory configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Preliminary recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Embedded display terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Monitoring Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Menu Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Submenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Graphic display option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Finding a parameter in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Detected fault screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Pre-alarms screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Modbus communication status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PCSoft software workshop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Structure of the parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Parameters that cannot be changed while the drive is running . . . . . . . . . . . . . . . . . . 37
Common control schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Drive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 3 Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Quick menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
S1A53838 09/2011 3
Table of Contents
Annex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Chapter 15 Migration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Migration ATV21 - ATV212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
4 S1A53838 09/2011
Table of Contents
Parameter values that vary According to drive rating, but not reset type . . . . . . . . . . 167
Parameter values that vary According to drive rating and reset type . . . . . . . . . . . . . 168
Parameter values that do not change if reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
S1A53838 09/2011 5
Table of Contents
6 S1A53838 09/2011
Safety Information
Safety Information
Important Information
NOTICE
Please read these instructions carefully and examine the equipment in order to familiarize yourself with the
device before installing, operating or carrying out any maintenance work on it.
The following special messages that you will come across in this document or on the device are designed to
warn you about potential risks or draw your attention to information that will clarify or simplify a procedure.
The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard
exists, which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death or serious
injury.
WARNING
WARNING indicates a potentially hazardous situation, which, if not avoided, can result in death, serious injury,
or equipment damage.
CAUTION
CAUTION indicates a potentially hazardous situation, which, if not avoided, can result in injury or equipment
damage.
CAUTION
CAUTION, used without the safety alert symbol, indicates a potentially hazardous situation which, if not
avoided, can result in equipment damage.
PLEASE NOTE
The word "drive" as used in this manual refers to the controller portion of the adjustable speed drive as defined
by NEC.
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No
responsibility is assumed by Schneider Electric for any consequences arising out of the use of this product.
2010 Schneider Electric. All Rights Reserved.
S1A53838 09/2011 7
About the Book
At a Glance
Document scope
The purpose of this document is to:
help you to set-up the drive,
show you how to program the drive,
show you the different menus, modes and parameters,
help you in maintenance and diagnostics.
Validity note
This documentation is valid for the Altivar 212 drive.
Related documents
Title of Documentation Reference Number
ATV212 Quick Start S1A53825
ATV212 Installation manual S1A53832
ATV212 Modbus manual S1A53844
ATV212 BACnet manual S1A53845
ATV212 Metasys N2 manual S1A53846
ATV212 Apoge FLN P1 manual S1A53847
ATV212 LonWorks manual S1A53848
Multiloader manual BBV48778
SoMove Mobile manual S1A51444
ATV212 other option manuals: see www.schneider-electric.com
You can download the latest versions of these technical publications and other technical information from our
website at www.schneider-electric.com.
8 S1A53838 09/2011
About the Book
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Read and understand this manual before installing or operating the drive. Installation, adjustment, repair,
and maintenance must be performed by qualified personnel.
The user is responsible for compliance with all international and national electrical code requirements with
respect to grounding of all equipment.
Many parts of this drive, including the printed circuit boards, operate at the line voltage. DO NOT TOUCH.
Use only electrically insulated tools.
DO NOT touch unshielded components or terminal strip screw connections with voltage present.
DO NOT short across terminals PA/+ and PC/ or across the DC bus capacitors.
Before servicing the drive:
- Disconnect all power, including external control power that may be present.
- Place a DO NOT TURN ON label on all power disconnects.
- Lock all power disconnects in the open position.
- WAIT 15 MINUTES to allow the DC bus capacitors to discharge.
- Measure the voltage of the DC bus between the PA/+ and PC/ terminals to ensure that the voltage is less
than 42 Vdc.
- If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative.
Do not repair or operate the drive.
Install and close all covers before applying power or starting and stopping the drive.
Failure to follow these instructions will result in death or serious injury.
DANGER
UNINTENDED EQUIPMENT OPERATION
Prevent accidental grounding of logic inputs configured for sink logic. Accidental grounding can result in
unintended activation of drive functions.
Protect the signal conductors against damage that could result in unintentional conductor grounding.
Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL
The designer of any control scheme must consider the potential failure modes of control paths and, for
certain critical control functions, provide a means to achieve a safe state during and after a path failure.
Examples of critical control functions are emergency stop and overtravel stop.
Separate or redundant control paths must be provided for critical control functions.
System control paths may include communication links. Consideration must be given to the implications of
unanticipated transmission delays or failures of the link (1).
Failure to follow these instructions can result in death, serious injury, or equipment damage.
(1) For additional information, refer to NEMA ICS 1.1 (latest edition), Safety Guidelines for the Application, Installation, and Maintenance of Solid
State Control and to NEMA ICS 7.1 (latest edition), Safety Standards for Construction and Guide for Selection, Installation and Operation
of Adjustable-Speed Drive Systems.
S1A53838 09/2011 9
About the Book
10 S1A53838 09/2011
General Overview
General Overview
I
What's in this Part?
This part contains the following chapters:
Chapter Chapter Name Page
1 Setup 13
2 Overview 15
S1A53838 09/2011 11
General Overview
12 S1A53838 09/2011
Setup
Setup
1
What's in this Chapter?
This chapter contains the following topics:
Topic Page
S1A53838 09/2011 13
Setup
INSTALLATION
PROGRAMMING
3. Configure
v the nominal frequency of the motor
[Parameter reset] (tYP) = [50 Hz reset] (1)
if this is not 50Hz,
v the motor parameters, page 66, only if the
Tips: factory configuration of the drive is not
z Before beginning programming, complete the customer suitable,
setting tables, page 171. v the application functions in the Drive Control
z Perform an auto-tuning operation to optimize performance, Parameters section, page 77 and the I/O
page 71. Control Parameters section, page 89, only if
z If you get lost, return to the factory settings, page 62. the factory configuration of the drive is not
suitable.
14 S1A53838 09/2011
Overview
Overview
2
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Factory configuration 16
Preliminary recommendations 17
Monitoring Mode 20
Run Mode 23
Programming Mode 23
Menu Navigation 24
Submenus 30
Pre-alarms screens 34
Drive Operation 45
S1A53838 09/2011 15
Overview
Factory configuration
Parameter which depends on Macro Programming [Auto set function] (AU4) = 0 (see page 63):
z Command reference: logic inputs ([Command mode sel] (CMOd) = 0). See page 77.
z Speed reference: analog input VIA = 010 V or 020 mA ([Frequency mode sel] (FMOd) = 1, (F201)= 0).
See [Frequency mode sel] (FMOd) page 77 and Analog Input Speed Reference page 106.
z F: run forward (F111= 2). See [LI F selection] page 90.
z R: preset speed 1 (F112= 6). See [LI R selection] page 90.
z RES: clear detected fault (F113= 10). See [LI RES selection] page 90.
z Drive ready for operation (F110= 1). See [Logic Funct 2 active] page 112.
If the above values are compatible with the application, the drive can be used without changing the settings.
16 S1A53838 09/2011
Overview
Preliminary recommendations
CAUTION
INCOMPATIBLE LINE VOLTAGE
Before turning on and configuring the drive, ensure that the line voltage is compatible with the supply voltage
range shown on the drive nameplate. The drive may be damaged if the line voltage is not compatible.
Failure to follow these instructions can result in equipment damage.
CAUTION
RISK OF DAMAGE TO THE DRIVE
z Avoid operating the contactor frequently.
z Power cycling must be MORE than 60 seconds.
Failure to follow these instructions can result in equipment damage.
DANGER
UNINTENDED EQUIPMENT OPERATION
Check that changes made to the settings during operation do not present any danger.
We recommend stopping the drive before making any changes.
Failure to follow these instructions will result in death or serious injury.
CAUTION
UNINTENDED EQUIPMENT OPERATION
Motor thermal protection will not be provided by the drive if the motor 's nominal current is 20% lower than that
of the drive. Find an alternative source of thermal protection.
Failure to follow these instructions can result in equipment damage.
CAUTION
RISK OF DAMAGE TO THE MOTOR
Motor thermal protection is no longer provided by the drive. Provide an alternative means of thermal protection.
Failure to follow these instructions can result in equipment damage.
CAUTION
RISK OF DAMAGE TO THE DRIVE
Using ATV212 in single phase supply is only allowed in training mode with motor and without load.
Failure to follow these instructions can result in equipment damage.
S1A53838 09/2011 17
Overview
1
4
2
RUN 5
%
PRG
3 MON Hz
Loc 8
MODE
Rem
6 9
ENT
7 10
12 STOP 11
RUN
RESET
13 14
LED/Key Characteristics
1 Display RUN LED Illuminates when a run command is applied to the drive.
Flashes when there is a speed reference present with a Run command.
2 Display PRG LED Illuminates when Programming mode is active.
Flashes in AUF, GrU modes
3 Display MON LED Illuminates when Monitoring mode is active.
Flashes in detected fault history display mode
4 Display unit 4 digits, 7 segments
5 Display unit LED The % LED illuminates when a displayed numeric value is a percentage.
The Hz LED illuminates when a displayed numeric value is in hertz.
6 UP/DOWN keys Depending on the mode, you can use the arrows to:
Navigate between the menus
Change a value
Change the speed reference when the UP/DOWN LED (7) is illuminated
7 UP/DOWN LED Illuminates when the navigation arrows are controlling the speed reference
8 Loc/Rem LED Illuminates when Local mode is selected
9 MODE Press to select the embedded display terminal mode.
Run mode (default on power-up)
Programming mode
Monitoring mode
Can also be used to go back to the previous menu.
10 Loc/Rem Switches between Local and Remote modes
11 ENT Press to display a parameters value or to save a changed value.
12 RUN LED Illuminates when the Run key is enabled
13 RUN Pressing this key when the RUN LED is illuminated starts the drive.
14 STOP Stop/reset key.
In Local mode, pressing the STOP key causes the drive to stop based on the setting of parameter [Loc.
mot stop mode] (F721).
In Remote mode, pressing the STOP key causes the drive to stop based on the setting of parameter
[Ext. fault stop Mode] (F603). The display will indicate a flashing E.
If [HMI reset button] (F735) is set to 0, pressing the stop key twice will reset the drive, if the detected
fault condition has been cleared.
18 S1A53838 09/2011
Overview
ATV212
RUN
%
drive
PRG
MON Hz Power Up Run Programming Monitoring
mode MODE mode MODE mode MODE
Loc
MODE
Rem
RUN
ENT
0.0 PRG AUF Fr-F
MON
Hz
STOP
RUN
RESET
The red LED in left side of the display indicates the current mode selected, RUN for Run mode, PRG for
Programming mode and MON for Monitoring mode.
S1A53838 09/2011 19
Overview
Monitoring Mode
The Monitoring mode displays drive operational data in real time. To access the Monitoring mode, press the
MODE key until the MON LED is illuminated. Then use the UP and DOWN keys to view up to 30 different types
of data.
RUN
C80
%
PRG
MON Hz
Loc
Rem
MODE
PRG AUF
ENT
F60.
0
STOP MODE
RUN
RESET
Fr-F
MON
25 other
parameters
MODE t0.
10
RUN
0.0
n---
MODE
20 S1A53838 09/2011
Overview
FL RYA-RYC
u101 [CPU CTRL ver.] CTRL version 101
uc01 [CPU MMI ver.] MMI version 1.0
uE01 [Memory ver.] Version of memory
d50.0 [PID feedback] Level of PID feedback, displayed either as Hz or in custom unit set by pa-
rameter [Customized freq val] (F702)
b70.0 [PID computed ref.] Speed reference command to drive as computed by the PID function, dis-
speed reference played either as Hz or in custom unit set by parameter [Customized freq
val] (F702)
h85 [Total input power] Accumulated input power consumed by the drive displayed in kWh
H75 [Total motor power] Accumulated output power supplied by the drive displayed in kWh
A16.5 [Drive out. rat. cur. A] Drive nameplate rated output current in amperes
1500 [Motor speed rpm] Motor speed in rpm
N50 [Comm. counter 2] Displays the counter numbers of communication through the network
n50 [Comm. counter 1] Displays the counter numbers of communication only at normal state in ev-
ery communication through the network
nErr [Past fault] The most recent detected fault stored in the detected fault history. If the
Examples: drive is in a detected fault state, this is not the active detected fault. A de-
- 1 blink Err5 tected fault is stored in the detected fault history after it is cleared by clear
- 2 blink Err5 detected fault action. Press ENT to review drive state at time of detected
- 3 blink CFI2 fault. See Detected fault Display and History on page 21 and Diagnostics
- 4 blink nErr and troubleshooting on page 149 for more detail. There are 4 detected
faults recorded. The detected fault 4 is cleared when a new detected fault
appears.
N...1 [Drive service alarm] ON:
OFF:
OpenStyle Tx
RJ45 Rx OpenStyle Rx
RJ45 Tx
t0.10 [Drive run time 100h] Cumulative drive run time. 0.01 = 1 hour.
1.00 = 100 hours
S1A53838 09/2011 21
Overview
FL RYA-RYC
t0.10 [Drive run time 100h] Cumulative drive run time. 0.01 = 1 hour. 1.00 = 100 hours
I/O Map
In both the monitoring mode and the detected fault history, it is possible to view the state of the logic inputs and
the relay outputs. See previous tables on pages 20 and 21.
Logic Input Map
ON:
OFF:
VIA F
R
RES
The ON or OFF status of each logic input is displayed in bits. VIA is included in this display if parameter F109
is set to either 1 or 2.
ON:
OFF:
FL RYA-RYC
22 S1A53838 09/2011
Overview
Run Mode
To access the Run mode, press the MODE key until the drive operating frequency, a detected fault code, or a
pre-alarm code is displayed.
See Diagnostics and troubleshooting beginning on page 149 for the detected fault and pre-alarm codes.
Programming Mode
Use this mode to program the drive.
To access the Programming mode, use the MODE key until the PRG indicator LED on the display is illuminated.
See Menu Navigation page 24.
S1A53838 09/2011 23
Overview
Menu Navigation
Menu navigation diagrams below illustrate how to navigate through the programming menus and submenus.
to AUH SUBMENU
to uLu
Programming
ENT [Quick menu]
mode
Fr-F AUF AU1 [Auto ramp]
MODE
MODE MODE
tHr [Motor thermal prot.]
FM [AO scaling]
FH [Max frequency]
ENT
F601 [Motor Current Limit]
to AUI
Fr [Local mot. Direction]
FM [AO scaling]
to AUF
24 S1A53838 09/2011
Overview
Programming to AUH
mode
Fr-F AUF SUBMENU [Quick menu]
MODE MODE
tHr [Motor thermal prot.]
FH [Max frequency]
SUBMENU
ENT
[5 LAST PARAM CHANGE]
(xxx)
MODE
FM [AO scaling]
(xxx)
FMSL [AO funct. selection]
ENT
AUH
MODE
S1A53838 09/2011 25
Overview
ENT
MODE MODE
tHr [Motor thermal prot.]
FH [Max frequency]
ENT
FM [AO scaling]
26 S1A53838 09/2011
Overview
Programming to AUH
mode
SUBMENU
[EXTENDED MENU]
GrU SUBMENU [ALL PARAM CHANGE] to F---
ENT
MODE
MODE
COM SUBMENU [COMMUNICATION MENU]
F102 [Freq.2 bandw.]
MODE
FH [Max frequency]
ENT
FM [AO scaling]
to AUF
S1A53838 09/2011 27
Overview
Programming to AUH
mode
Fr-F AUF SUBMENU [Quick menu]
FM [AO scaling]
to FMSL
FMSL [AO funct. selection]
[Auto ramp]
AU1
to AUF
28 S1A53838 09/2011
Overview
Programming to AUH
mode
Fr-F AUF SUBMENU [Quick menu]
to F800
IO SUBMENU [I/O MENU] to COM
ENT
MODE
FM [AO scaling]
to AUF
S1A53838 09/2011 29
Overview
Submenus
The ATV212 drive features 6 submenus (see diagrams starting on page 24) that are designed to reduce the time and
effort required to program application parameters. Parameters can be modified within these submenus.
F [EXTENDED MENU]
The extended parameter submenu provides access to parameters used for special settings and applications.
10 [I/O MENU]
The IO submenu provides access to parameters used for input/output setting.
30 S1A53838 09/2011
Overview
WARNING
LOSS OF CONTROL
z Do not use the ATV21 and ATV12 terminal display (VW3A21101 and VW3A1006).
z Only VW3A1101 is compatible with ATV212.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
1 Graphic display
7 ESC key: Press to select the
graphic display mode.
- Run mode (default on power-up)
2 Function keys
- Programming mode
F1, F2 and F3: not
- Monitoring mode
assigned
Can also be used to go back to
F4: Loc/Rem
the previous menu.
Also corresponds to the MODE
3 STOP/RESET key
button of the embedded HMI
4 RUN key
6 FWD/REV key: Press to
reverse the direction of rotation of
the motor
5 Jog dial:
Press (ENT):
- To save the current value
- To enter the selected menu or parameter
Turn +/-:
- To increment or decrement a value
- To go to the next or previous line
- To increase or decrease the reference if control via the graphic
display option is activated
Note: Keys 3, 4, 5 and 6 can be used to control the drive directly, if control via the graphic display option is
activated.
S1A53838 09/2011 31
Overview
Powering up the drive with graphic display option for the first time
When powering up the graphic display option for the first time, the user has to select the required language.
LANGUAGE Display after the graphic display option has been powered up for the first time.
English Select the language and press ENT.
Franais
Deutsch
Italiano
Espaol
Chinese
Trke
ENT
MAIN MENU
DRIVE MENU
LANGUAGE
ATV212H075M3X
0.75kW/1HP 200 / 240 V
2 s or ENT
OPERATIONAL VALUE
0 Hz
Rem Loc/Rem
32 S1A53838 09/2011
Overview
Example: ACC
Then use the parameter code index, page 171, to find the page giving details of the displayed parameter.
Rem Loc/Rem
This screen is displayed the detected fault type and diagnostic information related to the detected fault. Then
use the alarm code table page 150 for more information.
Line undervoltage
OPERATIONAL VALUE
MOFF: Line Undervolt fault
Rem Loc/Rem
S1A53838 09/2011 33
Overview
Pre-alarms screens
Here some type of screens:
29.0 Hz 29.0 Hz
29.0 Hz 29.0 Hz
Current Limit and DC bus overvoltage Motor overload and drive overheating
pre-alarm pre-alarm
29.0 Hz 29.0 Hz
RJ45:
Rem Loc/Rem
Mb activity on RJ45 port
34 S1A53838 09/2011
Overview
Description
This PC software workshop is a user-friendly tool for setting up Altivar 212 drives.
It includes different functions such as:
z Configuration preparation
z Setup
z Maintenance
Connection
The PCSoft software workshop must be connected directly to the Modbus port on the drive using the PC serial
port connection kit, reference VW3A8106 or by USB cable reference TCSMCNAM3M002P, or by bluetooth (see
catalog on www.schneider-electric.com).
S1A53838 09/2011 35
Overview
0 [Disabled]
1 [Initialize constant]: Application of individual settings of Auto Torque Boost [Auto Torque Boost]
(F402)
2 [Complete tune]: complete auto tuning.
Parameter F400 is reset to 0 after the auto tuning is performed.
Note: The text in square brackets [ ] indicates what you will see on the graphic display option.
36 S1A53838 09/2011
Overview
S1A53838 09/2011 37
Overview
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Read and understand the instructions in "before you begin" chapter, before performing the procedure in this
section.
Failure to follow these instructions will result in death or serious injury.
DANGER
UNINTENDED EQUIPMENT OPERATION
z To modify the setting of the switches, the product must be switched off.
z Do not change the setting of switch SW102 unless your system is properly wired.
Failure to follow these instructions will result in death or serious injury.
2-wire control
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F Run forward
FLC
ENT R Run reverse
FLB
FLA RES
RUN STOP
RYA PLC
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
Note: If F111 and F112 are switched simultaneously, the drive will go at 0 speed.
38 S1A53838 09/2011
Overview
3-wire control
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
ENT R Start forward
FLB
FLA RES
RUN STOP Stop
RYA PLC
Start reverse
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
Reverse run
ON
R - Stop OFF
ON
F - Forward start OFF
ON
RES - Reverse start OFF
ON
Line power OFF
S1A53838 09/2011 39
Overview
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
ENT R
FLB
FLA RES
RUN STOP
RYA PLC
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
2.2 to 10 kOhms
1/4 Watt
40 S1A53838 09/2011
Overview
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
ENT R
FLB
FLA RES
RUN STOP
RYA PLC
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
S1A53838 09/2011 41
Overview
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
ENT R
FLB
FLA RES
RUN STOP
RYA PLC
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
1. Wire the logic and analog inputs as indicated in the above figure.
2. Set switch SW102 to source.
3. Program common parameters of ATV212 (see Quick Menu page 55).
4. Program specific parameters for preset speed as indicated in the following table:
Parameter Page Setting Factory value
F109 [VIA selection] 90 2 [LI source] 0
F111 [LI F selection] 90 2 [forward] 2
F112 [LI R selection] 90 6 [PS1] 6
F113 [LI RES selection] 90 7 [PS2] 10
F118 [VIA LI selection] 90 8 [PS3] 7
Sr1 [Preset speed 1] 112 - 15.0
Sr2 [Preset speed 2] 112 - 20.0
Sr3 [Preset speed 3] 112 - 25.0
Sr4 [Preset speed 4] 112 - 30.0
Sr5 [Preset speed 5] 112 - 35.0
Sr6 [Preset speed 6] 112 - 40.0
Sr7 [Preset speed 7] 112 - 45.0
Output
frequency
(Hz)
0 Time (sec)
ON
F OFF
ON
R OFF
ON
RES OFF
ON
VIA OFF
42 S1A53838 09/2011
Overview
Serial communication
RJ45 connection Port open style connection
Contact Signal
PO PA/+ PC/- B +
U/T1
A -
R/L1
S/L2 V/T2 GND GND
T/L3 W/T3
M SCR Screen
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
ENT R
Cable sheath should be peeled off by about
FLB 10 mm.
FLA RES
RUN STOP For wiring work, use a fat blade screwdriver
RYA PLC with a 0.6 mm thick and 3.5 mm width
RYC P24 blade.
FM CC Tightening torque for the terminal block is
PLC I U Term
Sink Source
FM 0.5 to 0.6 Nm.
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
1. For Modbus serial communication, plug the network cable into RJ45 connector on the main control board.
Connection can also be carried out using the open style port.
2. Program common parameters of ATV212 (see Quick Menu page 55).
3. Program specific parameters for serial communication as indicated in the following table:
Parameter Page Setting Factory value
CMOd [Command mode sel] 77 2 [Communication] 0
FMOd [Frequency mode sel] 77 4 [Serial com ref.] 1
F807 [Com channel choice] 139 1
Forced local
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
ENT R
FLB
FLA RES
RUN STOP Forced
RYA PLC
local
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
S1A53838 09/2011 43
Overview
PID control
PO PA/+ PC/-
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
M
RUN
%
PRG
MON Hz
Loc
Rem
MODE F
FLC
R
FLB
ENT
P Feedback
FLA RES transmitter
RUN STOP
RYA PLC
RYC P24
PLC
FM CC
I U Term
Sink Source
FM
SW102 SW101 SW103
VIA U I
VIB U PTC
SW100
Setpoint 0 - 10 V
44 S1A53838 09/2011
Overview
Drive Operation
In remote mode, the ATV212 drive is operated from a combination of the command and speed reference sources
defined by programming parameters [Frequency mode sel] (FMOd) and [Command mode sel] (CMOd) (see
page 77).
Command Sources
The command source [Command mode sel] (CMOd) choices are:
z External signals to the control terminal logic inputs F, R, RES and VIA
z Serial communication control (Modbus, Metasys N2, Apogee FLN P1, BACnet, or LonWorks)
z Embedded display terminal RUN and STOP keys or graphic display option
S1A53838 09/2011 45
Overview
Up/Down speed
5 Communication
OFF Speed
LOC SetPoint
Terminal Local
Graphic display option
F207
1
VIA
VIB 2 F807
Terminal Local 3 RJ45 channel: Modbus
Graphic display
option Communication
4 Network channel:
Communication Paremeter F829
Up/Down speed 5
Default value
Parameters [Command mode sel] (CMOd) and [Frequency mode sel] (FMOd) are the first layers of logic used
by the drive to determine its command CMOd and speed reference FMOd source.
[Remote spd ref 2] (F207) is a secondary speed reference source that may override the source selected by
FMOd (see page 77).
The speed reference source identified by F207 takes control if either:
z A logic input assigned to function 38 (frequency reference source switching) is enabled, or
z Parameter [Auto/man speed ref] (F200) is set to 1 and the drive's output frequency is equal to or less than
1 Hz (see page 108).
If a serial communication link is established, it can take control of the ATV212 drive, overriding inputs identified
by CMOd, FMOd, and F207. Control is restored to CMOd, FMOd, and F207 only if:
z The serial communication link relinquishes control, or
z A logic input assigned to function 48 (forced local) is enabled.
The final layer of logic used by the drive to determine its command source is the LOC/REM key on the graphic
display option.
When the drive and embedded HMI is set to local mode (by pressing the LOC/REM key, lighting the local mode
LED), the drive responds only to commands from the embedded and graphic display option.
46 S1A53838 09/2011
Overview
DANGER
UNINTENDED EQUIPMENT OPERATION
z Know the state of the frequency and run commands from the remote source before exiting the local mode.
z Upon entering the remote mode, the drive will respond to the most recent command from the remote source,
even if it was received before entering or while in the local mode.
Failure to follow these instructions will result in death or serious injury.
Switching between local and remote mode is achieved with the LOC/REM key on the drives embedded display
terminal or with F4 key on the graphic display option.
The LOC/REM key can be disabled by setting parameter [Loc/rem key] (F732) to 1 (see page 80).
When parameter [Switch rem/Local] (F295) is set to 1 (factory setting), a bumpless tranfer of motor operation
is achieved when switching from remote to local mode (see page 78).
For example, if the bumpless transfert feature is active and if the motor is running at full speed with the drive in
remote mode, the motor will still run at full speed after the drive is transferred to local mode.
Conversely, when switching from local to remote mode, the run and speed command is not transferred to the
remote mode. Upon entering the remote mode, the drive will operate on the run and speed command set by the
remote source even if it was received before entering or while in the local mode.
The diagram below is an example timing diagram.
S1A53838 09/2011 47
Overview
Local Mode
When the ATV212 drive is in local mode, the LED above the LOC/REM key is illuminated.
On the graphic display option:
Motor rotation is indicated on the embedded display terminal as Fr-F for forward and as Fr-r for reverse.
The ability to run in the Forward or Reverse direction can be set with parameter [Motor direction] (F311) (see
page 86).
48 S1A53838 09/2011
Overview
Use of the STOP key as a clear detected fault can be set with parameter [HMI reset button] (F735) (see page
80).
In the event of an OL1 or OL2 detected fault, the following time periods are necessary before a clear detected
fault is possible:
z OL1 (drive overload)about 30 seconds after the detected fault has occured
z OL2 (motor overload)about 120 seconds after the detected fault has occured
S1A53838 09/2011 49
Overview
Remote Mode
When the ATV212 drive is in the remote mode, the LOC/REM LED is off.
The drive responds to commands sent over the RJ45 communication port if parameter [Com channel choice]
(F807) is set to 0. Other protocols are available when F807 is set to 1 on open style port.
The analog signal type depends on the setting of switch SW100 and parameters F109, F201F204, and
F470F471.
The control that VIB has over motor speed depends on the setting of switch SW100 and parameters F210
F213, F472F473, and F645.
50 S1A53838 09/2011
Overview
S1A53838 09/2011 51
Overview
In the event of an OL1 or OL2 detected fault, the following time periods needs to pass before a clear detected
fault is possible:
z OL1 (drive overload) - about 30 seconds after the occurrence of the event.
z OL2 (motor overload) - about 120 seconds after the occurrence of the event.
52 S1A53838 09/2011
Programming
Programming
II
What's in this Part?
This part contains the following chapters:
Chapter Chapter Name Page
3 Quick Menu 55
4 Programming Parameters 61
5 Motor Control Parameters 65
6 Drive Control Parameters 77
7 Application Parameters 81
8 I/O Control Parameters 89
9 Display Parameters 119
10 Detected Fault Management Parameters 123
11 Serial Communication Parameters 137
12 Start/Stop Control By Speed Reference Level 143
13 Droop Control 145
S1A53838 09/2011 53
Programming
54 S1A53838 09/2011
Quick Menu
Quick Menu
3
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Quick menu 56
S1A53838 09/2011 55
Quick Menu
Quick menu
The AUF submenu provides ready access to the ten basic parameters commonly used in programming the
drive.
In many cases, programming the ATV212 drive is complete when these 10 parameters and motor parameters
have been properly set. .
0 [Disabled]
1 [Enable]: [Acceleration time 1] (ACC) and [Deceleration time 1] (dEC)
2 [ACC only]: [Acceleration time 1] (ACC) only
If parameter AU1 is set to 1 or 2, the drive will monitor its own loading level and optimize the acceleration and deceleration
ramps. The acceleration and deceleration AU1 = 1 only rates will be automatically adjusted between 1/8 to 8 times the settings
of ACC and dEC, depending on the drives current rating and the load level on the motor. ACC and dEC should be appro-
priately set for an average load in the application. If the load on the motor increases rapidly during ramp up or ramp down, the
auto ramp adaptation feature may not help to prevent the drive from experiencing an overcurrent or overvoltage.
If the application requires a consistent acceleration and deceleration time, set AU1 to 0, and set ACC and dEC manually as
needed. The manual acceleration and deceleration times can still be overridden by the [Motor Current Limit] (F601) (see page
69) and [Overvoltage fault] (F305) (see page 128) and [Overvoltage level] (F626) (see page 128) functions.
ACC [Acceleration time 1] 0.0 to 3200 s According to drive
rating (1)
The setting of parameter ACC determines the slope of the acceleration ramp and the time it takes for the output frequency of the
drive to increase from 0 Hz to the setting of [Max frequency] (FH) (see page 82).
If parameter [Auto ramp] (AU1) is set to 1 or 2, the acceleration ramp may be increased or decreased from the setting of ACC,
depending on the amount of load on the motor during ramp up.
If two different acceleration rates are needed, see parameter [Acceleration time 2] (F500) on page 83.
Output frequency (Hz)
0
Time (s)
The setting of parameter dEC determines the slope of the deceleration ramp and the time it takes for the output frequency of
the drive to decrease from the setting of [Max frequency] (FH) to 0 Hz.
If parameter [Auto ramp] (AU1) is set to 1 or 2, the deceleration ramp may be increased or decreased from the setting of dEC,
depending on the amount of load on the motor during ramp down. See diagram above.
If two different deceleration rates are needed, see parameter [Deceleration time 2] (F501) on page 83.
Parameter LL sets the minimum frequency that can be commanded to the drive by the local or remote speed reference source.
Parameter UL sets the maximum frequency that can be commanded to the drive by the local or remote speed reference source.
The top end of its range is limited by the setting of [Max frequency] (FH).
(1) See table page 167
56 S1A53838 09/2011
Quick Menu
tHr [Motor thermal prot.] Motor Rated Current Overload Setting 10 to 100% of the 100%
drives output cur-
rent rating
Set parameter tHr to the motors rated current as indicated on the motor nameplate for the selected operating voltage.
If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter tHr will be adjusted in amperes.
If parameter F701 is set to 0, parameter tHr will be adjusted in percentage. In this case, divide the motor rated current by
the drive rated current (as listed on its nameplate) and set parameter tHr to the resulting percentage.
The setting of parameter [Switch. freq. level] (F300) does not change the drives rated current for the sake of this calculation
(see page 85).
Parameter FM is used to match the FM terminal output signal with the input requirements of the attached panel meter by adjusting
the slope and bias of the analog output signal. Before adjusting FM, set FMSL to either 15 or 17. As you adjust the value of
FM, monitor the display on the attached panel meter. When the meter display reaches 100%, press the ENT key on the drive
display terminal. The drive will flash between FM and the adjusted value, indicating that the adjustment has been saved.
S1A53838 09/2011 57
Quick Menu
Set parameter uL (vL) to the motors rated frequency as indicated on the motor nameplate.
Note: It is possible to set the drives various motor control frequencies to 50 Hz by setting [Parameter reset] (tYP) to 1, the 50
Hz reset. For more information, see page 62.
Set parameter uLu (vLv) to the motors rated voltage as indicated on the motor nameplate.
ATV212pppM3X: 50 to 330 V.
ATV212pppN4: 50 to 660 V
Note: Drive output voltage cannot be set to exceed the input line voltage level.
(1) See table page 167
58 S1A53838 09/2011
Quick Menu
Motor parameters
Configure the motor parameters and perform an auto-tuning ([Auto-tuning drive] (F400) = 2, see page 71 for
auto-tuning).
F415 [Motor rated current] Motor rated full load current 0.1 to 200.0 A According to drive
rating (1)
Set parameter F415 to the motor rated full load current in amperes as indicated on the motors nameplate.
Set parameter F417 to the motor rated speed in rpm as indicated on the motors nameplate.
CAUTION
RISK OF DAMAGE TO THE MOTOR AND THE DRIVE
z Check that the motor will withstand this current.
z Check that the profile mission complies with the derating curve given in the installation manual
Failure to follow this instruction can result in equipment damage.
Display the letter C and the output frequency flashing on the embedded software terminal, ex:
If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter F601 will be adjusted in amperes. If param-
eter F701 is set to 0, parameter F601 will be adjusted as a percentage of the drives output rated current as listed on its
nameplate.
The setting of parameter [Switch. freq. level] (F300) (see page 85) does not change the drives rated current for the sake of
this calculation.
Do not set parameter F601 below the no-load current rating of the motor.
DANGER
HAZARD OF ELECTRIC SHOCK OR ARC FLASH
z During auto-tuning, the motor operates at rated current.
z Do not service the motor during auto-tuning.
Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL
z It is essential that the following parameters uLu (vLv), uL (vL), F415 and F417 are correctly configured before
starting auto-tuning.
z When one or more of these parameters have been changed after auto-tuning has been performed, F400 will return 0
and the procedure will have to be repeated.
Failure to follow these instructions can result in death or serious injury.
0 [Disabled]: Disabled
1 [Initialize constant] (2): Auto-tuning is performed immediatly if possible. Parameter Auto Torque Boost [Auto Torque Boost]
(F402) may need adjustment
2 [Complete tune] (2): complete auto tuning
(1) See table page 168.
(2) Parameter F400 is reset to 0 after the auto tuning is performed.
S1A53838 09/2011 59
Quick Menu
60 S1A53838 09/2011
Programming Parameters
Programming Parameters
4
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Parameter Reset 62
Parameter Lock 64
S1A53838 09/2011 61
Programming Parameters
Parameter Reset
DANGER
UNINTENDED EQUIPMENT OPERATION
When tYP is set to 3 or 8:
- Check that the modification of the current configuration is compatible with the wiring diagram used.
- All logic inputs must be deactivated to avoid unintended restart.
Failure to follow these instructions will result in death or serious injury.
0 [No action]
1 [50 Hz reset]: 50 Hz parameter reset
Setting parameter tYP to a value of 1 will set specific parameters to values suitable for many 50 Hz (motor base frequency) ap-
plications.
See Parameters whose values after a reset vary by reset type table on page 166 and table on page 168 for a list of parameters that
are affected by this reset action and their resultant values.
2 [60 Hz reset]: 60 Hz parameter reset
Setting parameter tYP to 2 sets specific parameters to values suitable for many 60 Hz (motor base frequency) applications. See
table "Parameters whose values after a reset vary by reset type" on page 166 and table "Parameters whose values after a reset
are drive model dependant but do not vary by reset type" on page 167 for a list of parameters that are affected by this reset action
and their resultant values.
3 [Factory set]: Factory reset
Setting parameter tYP to 3 resets most parameters to their factory settings. See tables listed below for a listing of the values that
will be copied into the drive by this factory reset action:
Parameters whose values after a reset do not vary by reset type (on page 162).
Parameters whose values after a reset vary by reset type (on page 166).
Parameters whose values after a reset are drive model dependant but do not vary reset type (on page 167).
Parameters whose values after a reset are drive model and reset type dependant (on page 168).
Parameters whose values do not change if a reset is performed (on page 169).
62 S1A53838 09/2011
Programming Parameters
DANGER
UNINTENDED EQUIPMENT OPERATION
Check that the selected macro configuration is compatible with the wiring diagram used.
Failure to follow these instructions will result in death or serious injury.
0 [Factory set]
Command reference: logic inputs (CMOd = 0). See page 77.
Speed reference: analog input VIA = 010 V or 020 mA (FMOd = 1, F201 = 0). See [Frequency mode sel] (FMOd) page 77 and
Analog Input Speed Reference page 106.
F: run forward (F111 = 2). See F Logic Input Function page 90.
R: preset speed 1 (F112 = 6). See R Logic Input Function page 90.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90.
Drive ready for operation (F110 = 1). See Active Logic Function 2 page 112.
1 [Run permissive]
Command reference: logic inputs (CMOd = 0). See page 77.
Speed reference: analog input VIA = 010 V or 020 mA (FMOd = 1). See [Frequency mode sel] (FMOd) page 77.
F: run forward (F111 = 2). See F Logic Input Function page 90.
R: run permissive (F112 = 1). See R Logic Input Function page 90.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90.
2 [3-wire]
Command reference: logic inputs (CMOd = 0). See page 77.
Speed reference: analog input VIA = 010 V or 020 mA (FMOd = 1). See See [Frequency mode sel] (FMOd) page 77.
F: run forward (F111 = 2). See F Logic Input Function page 90.
R: stop ramp (F112 = 49). See R Logic Input Function page 90.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90.
3 [+/- Speed]
Command reference: logic inputs (CMOd = 0). See page 77.
Speed reference: +/- Speed (FMOd = 5). See See [Frequency mode sel] (FMOd) page 77
F: run forward (F111 = 2). See F Logic Input Function page 90.
R: + Speed (F112 = 41). See R Logic Input Function page 90.
RES: - Speed (F113 = 42). See RES Logic Input Function page 90.
(1) When programming parameter AU4, the embedded display terminal will display two numbers. The left number is the value
last entered into AU4. The right number will be 0. Use the UP/DOWN keys to change the right number to the desired value
and press ENT. Entering 0 into AU4 has no effect on the drive. Programming 0 into AU4 will not return the seven
parameters to their factory default values.
S1A53838 09/2011 63
Programming Parameters
Parameter Lock
Code Name / Description Factory setting
The setting of this parameter determines whether the AUF submenu, Quick Menu, will be displayed on the HMI (see page 30).
0 [AUF displayed]: AUF parameter displayed
1 [AUF hidden]: AUF parameter hidden
64 S1A53838 09/2011
Motor Control Parameters
5
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Motor Tuning 70
Auto-tuning 71
Expert parameters 72
S1A53838 09/2011 65
Motor Control Parameters
Constant V/Hz Mode with AutomaticTorque Boost ([Mot cont. mode sel.] (Pt) = 2)
Use parameter [Auto Torque Boost] (F402) to adjust the amount of automatic torque boost (see page 74).
If the ATV212 drive and the connected motor have the same power rating, and if the motor has a nominal
1500 rpm rating, no motor auto-tuning is required to use this motor control mode. Otherwise, follow the steps
outlined in Motor Tuning on page 70.
Due to the feedback circuit used in this mode, it is possible for motor speed to oscillate. If this occurs, select the
Constant V/Hz mode ([Mot cont. mode sel.] (Pt) = 0) and adjust torque boost manually with parameter [Motor
Voltage Boost] (ub).
Sensorless vector control will not improve motor control above the motors rated speed.
Sensorless vector control is more effective if the motor leads are less than 30 m (100 ft) in length. If motor leads
longer than 30 m (100 ft) are required, perform an auto-tuning with the long motor leads included in the circuit.
Motor torque may not be maximized at the motors rated frequency due to voltage drop in the motor leads.
Connecting a load reactor or a motor filter on the output of the ATV212 drive may reduce the torque generated
by the motor in sensorless vector control mode. Auto-tuning will most likely not be possible with a reactor or filter
attached to the drive. Manual tuning will be required
66 S1A53838 09/2011
Motor Control Parameters
S1A53838 09/2011 67
Motor Control Parameters
Relationship Between [Mot cont. mode sel.] (Pt) setting and Other Motor Parameters
X: Not applicable for the [Mot cont. mode sel.] (Pt) setting
: Adjustment of this parameter is required.
O: Adjust this parameter if necessary.
Low speed motor torque can be adjusted with parameter ub when parameter [Mot cont. mode sel.] (Pt) (see page 67) is set
to 0 (Constant V/Hz) or 1 (Variable Torque). See curves on page 66 for more information.
If nuisance overcurrent faults occur during starting, reducing the setting of parameter ub may help.
(1) See table page 167.
68 S1A53838 09/2011
Motor Control Parameters
CAUTION
RISK OF DAMAGE TO THE MOTOR AND THE DRIVE
z Check that the motor will withstand this current.
z Check that the profile mission complies with the derating curve given in the installation manual
Failure to follow this instruction can result in equipment damage.
Display the letter C and the output frequency flashing on the embedded software terminal, ex:
If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter F601 will be adjusted in amperes. If param-
eter F701 is set to 0, parameter F601 will be adjusted as a percentage of the drives output rated current as listed on its
nameplate.
The setting of parameter [Switch. freq. level] (F300) (see page 85) does not change the drives rated current for the sake of
this calculation.
Do not set parameter F601 below the no-load current rating of the motor.
S1A53838 09/2011 69
Motor Control Parameters
Motor Tuning
Tuning the drive to specific motor values will optimize motor performance if parameter [Mot cont. mode
sel.] (Pt) (see page 67) is set to:
z 2 (constant V/Hz with automatic boost),
z 3 (sensorless vector control), or
z 4 (energy savings)
At a minimum, manually set parameters uL (vL), uLu (vLv), F415, F416, and F417.
Parameters [Slip Compensation] (F401), [Auto Torque Boost] (F402), [Frequency loop gain] (F418) and
[Freq. loop stability] (F419) can be set manually or they can be set automatically using the auto tuning
function, parameter [Auto-tuning drive] (F400).
More precise motor control adjustments can be made with parameters F307, F480, F485, F492, and
F494 F496.
Set parameter uLu (vLv) to the motors rated voltage as indicated on the motor nameplate.
ATV212pppM3X: 50 to 330 V.
ATV212pppN4: 50 to 660 V
Note: Drive output voltage cannot be set to exceed the input line voltage level.
Set parameter uL(vL) to the motors rated frequency as indicated on the motor nameplate.
Note: It is possible to set the drives various motor control frequencies to 50 Hz by setting [Parameter reset] (tYP) to 1, the
50 Hz reset. For more information, see page 62.
tHr [Motor thermal prot.] Motor rated current overload setting 10 to 100% of the 100%
drives output cur-
rent rating
Set parameter tHr to the motors rated current as indicated on the motor nameplate for the selected operating voltage.
If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter tHr will be adjusted in amperes.
If parameter F701 is set to 0, parameter [Motor thermal prot.] (tHr) will be adjusted in percentage. In this case, divide the
motor rated current by the drive rated current (as listed on its nameplate) and set parameter tHr to the resulting percentage.
The setting of parameter [Switch. freq. level] (F300) does not change the drives rated current for the sake of this calcu-
lation (see page 85).
F607 [Mot overload time] Motor overload time 10 to 2400 s 300 s
CAUTION
RISK OF DAMAGE TO THE MOTOR
Check that the motor will withstand this time without overheating
Failure to follow this instruction can result in equipment damage.
Parameter F607 determines how long the drive will support a 150% motor overload before a fault detection occurs.
F415 [Motor rated current] 0.1 to 200.0 A According to
drive rating (1)
Set parameter F415 to the motor rated current in amperes as indicated on the motors nameplate.
F416 [Mot no-load current] Motor no-load current 10.0 to 100.0% According to
drive rating (1)
Set parameter F416 to the ratio of the motors no load current to its rated current.
F417 [Motor rated speed] Motor rated speed 100.0 to 15000 rpm According to
drive rating (1)
Set parameter F417 to the motor rated speed in rpm as indicated on the motors nameplate.
70 S1A53838 09/2011
Motor Control Parameters
Auto-tuning
Before performing an auto-tune, verify that:
z A motor is connected and any load-side disconnect is closed.
z The motor is completely stopped and de-energized.
z The motor should be cool (room temperature).
z There is only one motor connected to the drive.
z All of the motor leads that will be used in the final installation are included in the output circuit during the auto-
tuning process.
z Motor leads are no longer than 30 m (100 ft). Motor leads longer than 30 m (100 ft) may result in reduced
motor torque and less than optimal motor control.
z No load reactors or filters are included in the motor circuit. Output reactors and filters may cause an auto-
tuning detected fault Etn1 and reduce effectiveness of sensorless vector control.
z The motor is not more than 1 hp size smaller than the drive.
z The motor has at least 2 and not more than 8 poles (750 to 3000 rpm).
z The motor does not have a high slip rating.
Auto tuning is performed upon the first start command after parameter [Auto-tuning drive] (F400) below is set
to 1 or 2 and is normally completed within 3 seconds. During the auto-tuning process, the graphic display option
displays Atn1.
During the auto-tuning process voltage is applied to the motor, although it barely rotates and produces very little
torque.
During the auto-tuning process, the drive checks for an output phase loss detection regardless of the setting of
parameter F605. An output phase loss detection EPH0 will abort the auto-tuning process.
If the auto-tuning process is unsuccessful, the drive will display Etn1. In this event, no results of the aborted
auto-tuning 1 will be saved in the drive, and a manual tuning of parameters [Slip Compensation] (F401), [Auto
Torque Boost] (F402), [Frequency loop gain] (F418) and [Freq. loop stability] (F419) will be required.
DANGER
HAZARD OF ELECTRIC SHOCK OR ARC FLASH
z During auto-tuning, the motor operates at rated current.
z Do not service the motor during auto-tuning.
Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL
z It is essential that the following parameters uLu, uL, F415 and F417 are correctly configured before starting auto-
tuning.
z When one or more of these parameters have been changed after auto-tuning has been performed, F400 will return 0
and the procedure will have to be repeated.
Failure to follow these instructions can result in death or serious injury.
Auto tuning enable
0 [Disabled]
1 [Initialize constant]: Auto-tuning is performed immediatly if possible. Application of individual settings of Auto Torque Boost [Auto
Torque Boost] (F402)
2 [Complete tune]: Complete auto tuning.
Parameter F400 is reset to 0 after the auto tuning is performed.
S1A53838 09/2011 71
Motor Control Parameters
Expert parameters
F390 [LL for ov.cur. prev.] Lower Limit function for Over Current Prevention 0.0 - UL 0.0
In the present software, motor speed is decreased to 0Hz in case the stall prevention state is continued.
When motor speed is lower than F390 during stall prevention, motor speed is kept to F390 to increase motor current.
In this situation, motor current is beyond stall prevention level (F601 or F185), therefore over current or over load
detected fault may occur in some case.
Frequency command
F390
0 Time
ON
RUN command (F or R)
OFF
ON
Over current alarm status
OFF
F480 [No load cur. coef] Magnetizing current coefficient 100 to 130% 100%
Use parameter F480 to fine tune motor torque during low-speed operation. To increase motor torque in the low-speed
operating range, increase the setting of parameter F480. However, only adjust parameter F480 if an auto tune does
not yield sufficient low-speed torque. Increasing the setting of parameter F480 may increase the motors no-load current
during low-speed operation. Do not set this parameter so that the motors no-load current exceeds its rated operating
current.
F485 [Stall control coef. 1] Stall prevention control coefficient 1 10 to 250 100
Use parameter F485 to adjust the drives response to large, sudden changes in load when the motor is operated above
its rated frequency. If a sudden change in load causes the motor to stall before the drive goes into current limit, gradually
reduce the setting of F485.
F492 [Stall control coef. 2] Stall prevention control coefficient 2 50 to 150 100
Use parameter F492 to adjust the drives response to a drop in the line supply voltage when the motor is operated above its
rated frequency. Such a drop in voltage often causes fluctuations in motor current or vibration in the motor. To reduce these dis-
turbances, set parameter F492 to a value between 80 and 90.
Note: Reducing the F492 setting increases the motor running current level.
DO NOT ADJUST.
F495 [Motor voltage coef.] Maximum voltage adjustment coefficient 90 to 120% 104%
Use parameter F495 to limit the drives maximum output voltage. Increasing this setting increases torque when the
motor is operated above its rated frequency, but may also cause motor vibration. Do not increase the value of F495 if
motor vibrations occur.
F496 [PWM adj. coef.] Waveform switching adjustment coefficient 0.1 to 14.0 kHz 14.0 kHz
Adjusting the value of parameter F496 may reduce motor noise and vibration during PWM waveform frequency shifts
in the mid-speed operating range.
72 S1A53838 09/2011
Motor Control Parameters
The drives output voltage will not exceed the input supply voltage.
If parameter F307 is set to 0 or 2, no corrections are made in the motor voltage gating process in response
to fluctuations in supply voltage. As a result, the V/Hz value of the output waveform to the motor will change in
proportion to the input voltage. Conversely, if F307 is set to 1 or 3, the V/Hz value of the output waveform will
be held constant, despite changes in the supply voltage level.
If parameter F307 is set to 0 or 1, output motor voltage will be limited to the value set by parameter
[Motor rated voltage] (uLu) (see page 70), even if the input supply voltage rises. If F307 is set to 2 or 3,
output motor voltage can rise above the level set by uLu if the input supply voltage rises above the motor rated
voltage.
If parameter [Mot cont. mode sel.] (Pt) is set to a value of 2, 3, 4, 5, or 6, the supply voltage is corrected,
regardless of the setting of parameter F307.
The diagrams below illustrate the impact of each setting of parameter F307.
F307 = 0 F307 = 1
Supply Voltage uncorrected, Motor Voltage Limited Supply Voltage corrected,
Motor Voltage Limited
0 0
Output Output
Frequency Frequency
F307 = 2 F307 = 3
Supply Voltage uncorrected, Motor Voltage Unlimited Supply Voltage corrected,
Motor Voltage Unlimited
Input Voltage High
Input Voltage High
uLu
x Input Voltage
Rated Voltage
Motor Voltage (V)
Low Low
0 0
Output Output
Frequency Frequency
F307 [Mot volt limitation] Supply Voltage Correction and Motor Voltage Limitation 3
S1A53838 09/2011 73
Motor Control Parameters
F170 [Mot 2 rated Freq.] Motor 2 rated frequency 25.0 to 200.0 Hz 50.0 Hz
Set parameter F170 to the motors rated frequency as indicated on the motor nameplate.
Note: It is possible to set the drives various motor control frequencies to 50 Hz by setting [Parameter reset] (tYP) to 1, the
50 Hz reset. For more information, see page 62.
F171 [Motor 2 rated Volt] Motor 2 rated voltage According to drive According to
rating (1) drive rating (1)
Set parameter F171 to the motors rated voltage as indicated on the motor nameplate.
ATV212pppM3X: 50 to 330 V.
ATV212pppN4: 50 to 660 V
Note: Drive output voltage cannot be set to exceed the input line voltage.
F173 [Motor 2 Overload] Motor 2 rated current overload setting 10 to 100% of the 100%
drives output cur-
rent rating
Set parameter F173 to the motors rated current as listed on the motor nameplate for the selected operating voltage.
F185 [Mot. 2 current limit] Motor 2 current limit 10 to 100% of the 110%
drives output cur-
rent rating
CAUTION
RISK OF DAMAGE TO THE MOTOR AND THE DRIVE
z Check that the motor will withstand this current.
z Check that the profile mission complies with the derating curve given in the installation manual.
Failure to follow this instruction can result in equipment damage.
Before adjusting parameter F401, verify that parameter [Motor rated speed] (F417) (see page 70) is set to the rated
speed of the motor in rpm. Parameter F401 can be used to fine tune the drives slip compensation feature. Increasing
the value of parameter F401 increases the drives compensation of motor slip.
F402 [Auto Torque Boost] 0.0 to 30.0% According to
drive rating (1)
Use parameter F402 to adjust the amount of automatic torque boost that is applied.
Motor rated voltage
Output Voltage (%)
: Automatically
adjusts the
amount of 0
torque boost.
Motor Rated Frequency Output Frequency (Hz)
74 S1A53838 09/2011
Motor Control Parameters
Parameters F418 and [Freq. loop stability] (F419) reduce the speed of the drives response to a change in speed command.
The factory setting of these two parameters assumes that the inertia of the load is three times as large as that of the motor shaft.
Adjust these two parameters if the factory setting is not appropriate for the application.
Note: It is possible for the drives output frequency to exceed its upper limit (parameter [Max frequency] (FH)) if the acceleration
parameter (ACC or F507) is set to its minimum value.
Increasing the setting of parameter F418 reduces the drives response time to changes in the speed reference.
Increasing the setting of parameter F419 further reduces the drives response to changes in the speed reference.
S1A53838 09/2011 75
Motor Control Parameters
76 S1A53838 09/2011
Drive Control Parameters
The setting of parameter CMOd determines the source of start, stop, forward, and reverse operation commands when the drive is
in remote mode.
The drive needs to be stopped to make changes to parameter CMOd.
See diagram on page 46 and description page 50 for more information on the source of the drives operation commands.
0 [Logic inputs]: Control terminal logic inputs
1 [HMI]: Graphic display option
2 [Communication]: Serial communication
FMOd [Frequency mode sel] Remote Mode Primary Speed Reference Source - 1
The setting of parameter FMOd determines the source of the drives speed reference when the drive is in remote mode.
The drive needs to be stopped to make changes to parameter FMOd.
See diagram on page 46 and description page 50 for more information on the source of the drives speed reference.
1 [Ref source VIA]: VIA
2 [Ref source VIB]: VIB
3 [HMI reference]: Graphic display option
4 [Serial com ref.]: Serial communication
5 [+/- Speed]: +/- Speed
The speed reference set by the UP/DOWN keys in local mode will be stored in parameter FC when the ENT key is pressed.
The next time the drive is started in local mode, it will accelerate the motor directly to the speed setpoint memorized by FC.
If Fr is set to 2 or 3:
The motor direction can be changed in local mode to forward by pressing the UP key while holding the ENT key and to reverse by
pressing the DOWN key while holding the ENT key.
The new motor direction will be displayed (forward = Fr-F, reverse = Fr-r) before the motor direction is reversed.
The motors last operating direction in local mode will be stored before a power removal or loss detection. When power is restored
to the drive, the local mode motor rotation direction will be the same as before the power loss detection.
If [Switch rem/Local] F295 (see page 78) is enabled and control is transferred from remote to local mode, the local mode operation
will assume the same motor rotation direction as in remote mode, regardless of the setting of Fr.
F707 [Loc. speed ref. step] Local Mode Speed Reference Step Changes - 0.0 Hz
If parameter F707 is enabled in local mode, the drives speed reference will change in steps equal to the setting of F707 each
time the UP or DOWN key is pressed.
Enabling parameter F707 only affects drive operation if parameter [Customized freq val] (F702) is set to 0.00. See page 121.
If the display flashes HI or LO, it indicates that repeated usage of the UP or DOWN keys has caused to drives speed reference
to reach either the [Low limit frequency] (LL) (see page 82) or the [Upper limit freq] (UL) (see page 82). This may happen if param-
eter F707 is set to a value larger than 0.00 Hz.
S1A53838 09/2011 77
Drive Control Parameters
F721 [Loc. mot stop mode] Local Mode Motor Stop Type - 0
The setting of parameter F721 determines the type of motor stop that will be executed when then embedded display terminal
STOP key is pressed.
The RUN and STOP keys needs to be enabled be setting parameter [Run/stop key] (F733) (see page 80) to 0 for the motor to
stop when the embedded display terminal STOP key is pressed.
If parameter F295 is enabled, the speed reference, run and direction commands will be transferred from remote to local mode
when the LOC/REM key is pressed. Operation of the drive is not affected by a remote to local control mode transition.
If parameter F295 is disabled, a remote to local control mode transition will cause the drive to remove power from the motor. A
new run command and speed reference will need to be entered in the local mode.
Regardless of the setting of parameter F295, a local to remote transition will cause the drive to immediately respond to the remote
commands present at the moment of the transition.
0 [Disable]: (0.0)
1 [Enable]: (0.01 to 600 seconds)
If parameter F256 is enabled and if the drive operates continuously at [Low limit frequency] (LL) (see page 82) for a time period
equal to the setting of F256, the drive will ramp the motor to a stop. While the motor is stopped, LStP will flash on the drive
embedded display terminal.
When the speed reference to the drive exceeds the low speed level LL+F391, the drive will accelerate the motor to the new speed
reference.
If parameter F256 is enabled, drive operation at or below the low speed level is also monitored during startup or during reversing
of the motor. See diagram below.
Output
frequency (Hz)
Time (s)
ON
OFF
Run
Command
1 VIA
2 VIB
3 HMI
4 Communication
5 +/- Speed
Parameter [Remote spd ref 2] (F207) defines the remote mode secondary speed reference source. The setting of parameter [Au-
to/man speed ref] (F200) (see page 108) determines whether this source is used for the speed reference.
If F200 is set to 0, a logic input terminal set to function 38 (see page 108) determines if [Remote spd ref 2] (F207) identifies the
speed reference source.
If F200 is set to 1, [Remote spd ref 2] (F207) is the speed reference source when the drives output frequency is 1 Hz or below.
See diagram on page 46 for more detail.
78 S1A53838 09/2011
Drive Control Parameters
WARNING
LOSS OF CONTROL
The value of F650 will impact the direction of the motor.
- Check wiring motor power UVW is correct.
- Verify that the value of F650 is convenient for this application.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
0 [Disable]
1 [Enable forward]
2 [Enable Reverse]
To enable Forced fire control, set parameter F650 to1 or 2 and assign a logic input to function 52 or 53 (see page 94). When
parameter F650 is set to1 or 2, the embedded display will briefly flash the code FIrE.
If parameter F650 is set to1 or 2 and a logic input assigned to function 52 or 53 is activated, the drive will run at the frequency
set by parameter [Forced speed freq.] (F294) (see below).
Note:
First set [Motor direction] (F311) page 86 to allow forward or reverse operation.
Push the ENT button for 2 sec to complete the setting.
See F659 for more information of the behavior.
F659 [Forced fire function] - 0
0 [Enable transition]
When parameter F659 is set to 0, the function is enabling on transition 0 -->1 of the logic input. The transition 1 -->0 will not disable
the function.
WARNING
LOSS OF CONTROL
If the Forced fire mode on logic input (function 52) has been enabled and F659 is set to 0, the drive will run and only removing
power from the drive will stop it.
If the Fire mode on logic input (function 53) has been enabled and F659 is set to 0, the drive will run and only removing power
from the drive or a fault detection or a pressing on the STOP key on the display terminal will stop the drive.
Check that this value of F659 is convenient for the application.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
1 [Enable level 1]
When parameter F659 is set to 1, if the logic input is set to 0 the function is disabled.
If the logic input is set to 1 the function is enable
WARNING
RISK OF APPLICATION MALFUNCTION
When F659 is set to 1 for safety reason, the forced mode will be inhibited if the logic input is inactivated for any reason (order
removed, input broken, wiring contact lost).
- Check that this value of F659 is conveniant for the application.
- If you need to continue to run if forced mode in any circonstance, select an other value of F659.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
2 [Enable level 0]
When parameter F659 is set to 2, if the logic input is set to 1 the function is disabled.
If the logic input is set to 0 the function is enable.
DANGER
UNINTENDED EQUIPMENT OPERATION
When F659 is set to 2 for safety reason, the motor will run at Forced speed F294 in case of intempestive wire disconnection.
- Check and control the wiring connection periodically.
- Protect the signal conductors against damage that could result in unintentional conductor grounding.
Failure to follow these instructions will result in death or serious injury.
The F294 parameter is used to set the fixed frequency command for the drive when it is in Forced or Fire mode.
S1A53838 09/2011 79
Drive Control Parameters
The setting of parameter F730 determines whether it is possible to set the drives speed by means of the embedded display ter-
minal in local mode.
0 [Enable]
1 [Disable]
Use parameter F732 to enable or disable the LOC/REM key on the drive embedded display terminal.
If the LOC/REM key is disabled, switching between local and remote mode can be achieved with parameters [Frequency mode sel]
(FMOd) and [Command mode sel] (CMOd). See page 77.
0 [Enable]
1 [Disable]
The setting of parameter F733 determines whether it is possible to start and stop the drive by the Run/Stop keys located
on the drive and graphic display option.
F734 [Priority stop] 0
WARNING
LOSS OF CONTROL
You are going to disable the stop button located on the drive and graphic display option
Do not select 1 unless exterior stopping methods exist.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
The setting of parameter F734 determines whether it is possible to stop the drive by the Stop key located on the drive and graphic
display option.
0 [Enable]
1 [Disable]
The setting of parameter [HMI reset button] (F735) determines whether it is possible to clear a drive detected fault by means of
the embedded display terminal STOP key (see page 51 for more detail).
0 [Enable]
1 [Disable]
80 S1A53838 09/2011
Application Parameters
Application Parameters
7
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Skip Frequencies 87
S1A53838 09/2011 81
Application Parameters
Application parameters
The setting of parameter FH determines the maximum output frequency of the drive.
FH limits the setting of parameter [Upper limit freq] (UL) (see page 82), which can be adjusted while the drive is operating.
Acceleration and deceleration rates are also affected by the setting of FH, as the definition of [Acceleration time 1] (ACC) or
[Deceleration time 1] (dEC) (see page 83) is the time it takes for the drive to ramp the motor up or down between zero speed
and the setting of FH.
FH can only be adjusted while the drive is stopped.
Output frequency (Hz) Output frequency (Hz)
UL [Upper limit freq] High speed 0.5 to [Max frequency] (FH) Hz 50.0 Hz
Parameter UL sets the maximum frequency that can be commanded to the drive by the local or remote speed reference source.
The top end of its range is limited by the setting of Maximum frequency [Max frequency] (FH). See diagram above.
LL [Low limit frequency] Low speed 0.0 to [Upper limit freq] (UL) Hz 0.0 Hz
Parameter LL sets the minimum frequency that can be commanded to the drive by the local or remote speed reference source.
See diagram above.
F240 [Mot start freq.] Output Starting Frequency 0.5 to 10.0 Hz 0.5 Hz
The setting of parameter F240 determines the drives output frequency at the moment it receives a start command. There is
no acceleration time to reach the parameter F240 level.
Parameter F240 is typically set for the rated slip frequency of the motor. This allows motor torque to be generated as soon as
a start command is given. Adjust parameter F240 when a delay in the motors response to a start command adversely affects
the application.
Example:
Motor no-load speed = 1500 rpm
Motor rated speed at full load = 1450 rpm
Motor rated frequency = 50 Hz
82 S1A53838 09/2011
Application Parameters
The setting of parameter ACC determines the slope of the acceleration ramp and the time it takes for the output frequency of
the drive to increase from 0 Hz to the setting of [Max frequency] (FH) (see page 82).
If parameter [Auto ramp] (AU1) (see page 85) is set to 1 or 2, the acceleration ramp may be increased or decreased from the
setting of ACC, depending on the amount of load on the motor during ramp up.
If two different acceleration rates are needed, see parameter [Acceleration time 2] (F500) on page 83.
0
Time (Sec)
The setting of parameter dEC determines the slope of the deceleration ramp and the time it takes for the output frequency of
the drive to decrease from the setting of [Max frequency] (FH) to 0 Hz.
If parameter [Auto ramp] (AU1) is set to 1, the deceleration ramp may be increased or decreased from the setting of dEC,
depending on the amount of load on the motor during ramp down. See diagram above.
If two different deceleration rates are needed, see parameter [Deceleration time 2] (F501) on page 83.
Parameter F500 sets the second acceleration time. Switching between acceleration rates 1 and 2 is accomplished by means
of:
Parameter [Ramp switching] (F504) (see page 85),
A particular operating frequency (see parameter [Commut. ramp freq.] (F505) on page 85), or
A logic input assigned to functions 5, 20, 21, 30, 31 35, or 40 (see table beginning on page 91)
Speed Reference
Time (S)
Acceleration/Deceleration Switching 0
Logic Input
(1) (2) (3) (4)
Parameter F501 sets the second deceleration time. Switching between deceleration rates 1 and 2 is accomplished by means
of:
- Parameter [Ramp switching] (F504) (see page 85),
- A particular operating frequency (see parameter [Commut. ramp freq.] (F505) on page 85), or
- A logic input assigned to functions 5, 20, 21, 30, 31 35, or 40 (see table beginning on page 91).
S1A53838 09/2011 83
Application Parameters
0 [Linear]
1 [S-ramp 1] (see diagram below)
2 [S-ramp 2] (see diagram below for [Acc/dec 2 pattern] (F503) parameter).
The linear acceleration and deceleration pattern is illustrated in diagram on page 83 and is used in most applications.
S-pattern 1 (see diagram below) is for use in applications that need the shortest ramp time possible while minimizing jerks during
speed changes. See below for more information about parameters [Acc/Dec S-pat start] (F506) and [Acc/Dec S-pat end]
(F507).
Set Frequency
0 Time (S)
x
x
0 [Linear]
1 [S-ramp 1] See diagram below.
2 [S-ramp 2] See previous diagram for parameter Acc/Dec Pattern 1 [Acc/dec 1 pattern] (F502).
S-pattern 2 (diagram below) is for use in high-speed spindle applications where acceleration and deceleration rates need to be
reduced as the motor operates above its rated operating frequencya constant hp region where motor torque is reduced.
Use parameter F503 to select the second Acc/Dec pattern. Switching between Acc/Dec patterns 1 and 2 is accomplished by
means of:
Parameter [Ramp switching] (F504) (see page 85),
A particular operating frequency (see parameter [Commut. ramp freq.] (F505) on page 85), or
A logic input assigned to functions 5, 20, 21, 30, 31 35, or 40 (see table beginning on page 91).
For more information on Acc/Dec patterns, see parameter [Acc/dec 1 pattern] (F502) above.
Set Frequency
Constant hp
Region
Motor Rated
Frequency
0
Time (S)
F506 [Acc/Dec S-pat start] Acc/Dec S-pattern lower limit 0 to 50% of acceleration time 10%
Use parameter F506 to adjust the lower portion of S-pattern 1. See diagram on page 85.
F507 [Acc/Dec S-pat end] Acc/Dec S-pattern Upper Limit 0 to 50% of acceleration time 10%
Use parameter F507 to adjust the upper portion of the S-pattern 1. See diagram on page 85.
84 S1A53838 09/2011
Application Parameters
1 [Ramp 1]
2 [Ramp 2]
Parameter F504 determines the Acc/Dec pattern.
Output Frequency (Hz)
Time (S)
F505 [Commut. ramp freq.] Acc/Dec pattern switching frequency 0.0 to [Upper limit freq] (UL) 0.0 Hz
(Hz)
If parameter F505 is set to a frequency greater than 0.0, the drive will use Acc/Dec pattern 1 above that frequency and Acc/Dec
pattern 2 above.
Speed Reference
Time (S)
Acceleration/Deceleration Switching 0
Logic Input
(1) (2) (3) (4)
0 [Disabled]
1 [Enable] - [Acceleration time 1] (ACC) and [Deceleration time 1] (dEC) (see page 83)
2 [ACC only] - [Acceleration time 1] (ACC) only
If parameter AU1 is set to 1 or 2, the drive will monitor its own loading level and optimize the acceleration and deceleration
ramps. The acceleration and deceleration (AU1 = 1 only) rates will be automatically adjusted between 1/8 to 8 times the settings
of [Acceleration time 1] (ACC) and [Deceleration time 1] (dEC), depending on the drives current rating and the load level on
the motor. ACC and dEC should be appropriately set for an average load in the application. If the load on the motor increases
rapidly during ramp up or ramp down, the auto ramp adaptation feature may not help prevent the drive from experiencing an over-
current or overvoltage.
If the application requires a consistent acceleration and deceleration time, set AU1 to 0, and set ACC and dEC manually as
needed. The manual acceleration and deceleration times can still be overridden by the [Motor Current Limit] (F601) (see page
69) and [Overvoltage fault] (F305) (see page 128) and [Overvoltage level] (F626) (see page 128) functions.
F300 [Switch. freq. level] Switching Frequency Level 6.0 to 16.0 kHz in 0.1 kHz steps According to
drive rating (1)
S1A53838 09/2011 85
Application Parameters
Random control of the switching frequency may reduce audible motor noise.
Random control of the switching frequency will not be performed if the switching frequency is set above 7.1 kHz, regardless of
the setting of F312.
0 [Disable]
1 [Enable]
If parameter F316 is set to 1 or 3, the switching frequency level will be automatically controlled to help prevent a drive over-
heating. If the drive senses an impending overheating, it will reduce the switching frequency, thus reducing heat produced by the
controller. As the temperature approaches normal, the switching frequency will return to the level selected by parameter [Switch.
freq. level] (F300).
If F316 is set to 1 or 3, motor control performance is optimized if parameter F300 is set to 6 kHz or 8 kHz.
86 S1A53838 09/2011
Application Parameters
Skip Frequencies
Do not set the skip frequency bands so that they overlap.
While the drive will not operate within these skip frequency bands during steady state operation, skip frequency
bands are ignored by the drive during motor acceleration and deceleration.
F270 [Jump frequency 1] Skip frequency 1 midpoint 0.0 to [Max frequency] (FH) Hz 0.0 Hz
F272 [Jump frequency 2] Skip frequency 2 midpoint 0.0 to [Max frequency] (FH) Hz 0.0 Hz
F274 [Jump frequency 3] Skip frequency 3 midpoint 0.0 to [Max frequency] (FH) Hz 0.0 Hz
S1A53838 09/2011 87
Application Parameters
The drive can inject DC current into the motor to apply braking torque to the load. Parameters [DC brake start
freq.] (F250), [DC braking current] (F251) and [DC braking time] (F252) determine the Output Starting
Frequency, current level, and braking time.
During DC injection braking, the drives switching frequency is 6 kHz regardless of the setting of parameter
[Switch. freq. level] (F300) (see page 85).
Output Frequency (Hz)
Speed Reference
DC Braking
0 Time (s)
DC braking
time
Run Command
ON
OFF
F250 [DC brake start freq.] 0.0 to [Max frequency] (FH) Hz 0.0 Hz
WARNING
NO HOLDING TORQUE
z DC injection braking does not provide holding torque at zero speed.
z DC injection braking does not work when there is a loss of power or when the drive detects a fault.
z When necessary, use a separate brake to maintain torque levels.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
When stopping the motor, the drive will apply DC injection braking once the output frequency drops below the level set
by parameter F250.
F251 [DC braking current] DC braking current level 0 to 100% 50% (1)
CAUTION
RISK OF DAMAGE TO THE MOTOR
Check that the motor will withstand this current without overheating.
Failure to follow this instruction can result in equipment damage.
Parameter F251 sets the level of current applied to the motor during DC injection braking. The displayed value, percent or
amperes, is set by parameter [Unit value selection] (F701) (see page 120).
During DC injection braking, the drives overload protection sensitivity increases. The drive automatically lowers the applied DC
current to avoid an overload detected fault.
CAUTION
RISK OF DAMAGE TO THE MOTOR
z Long periods of DC injection braking can cause overheating and damage the motor.
z Protect the motor by avoiding long periods of DC injection braking.
Failure to follow this instruction can result in equipment damage.
Parameter F252 determines how long DC injection braking is applied to the motor.
(1) Percentage of the drive's rated current or ampere range. This will vary according to drive power rating.
88 S1A53838 09/2011
I/O Control Parameters
8
What's in this Chapter?
This chapter contains the following topics:
Topic Page
S1A53838 09/2011 89
I/O Control Parameters
The setting of parameter F111 determines the control function of logic input terminal F.
The setting of parameter F112 determines the control function of logic input terminal R.
The setting of parameter F113 determines the control function of logic input terminal RES.
DANGER
UNINTENDED EQUIPMENT OPERATION
Prevent accidental grounding of logic inputs configured for sink logic. Accidental grounding can result in unin-
tended activation of drive functions.
Protect the signal conductors against damage that could result in unintentional conductor grounding.
Failure to follow these instructions will result in death or serious injury.
0 [AI]: Analog input
1 [LI sink]: Logic input - sink (negative logic)
2 [LI source]: Logic input - source (positive logic)
The setting of parameter F109 determines whether control input terminal VIA will serve as an analog input (0-10 Vdc or 0
20 mA) or as a logic input (either sink or source).
When configuring VIA as a logic input, be certain to slide switch SW100 on the main control board to the V (voltage) position.
When configuring VIA as a logic input using sink (negative) logic, be certain to connect a 4.7 k (1/2 W) resistor between control
terminals P24 and VIA.
For more information on the use of control input terminal VIA, see ATV212 Installation manual.
Set first parameter [VIA selection] (F109) before setting parameter F118. The setting of parameter F118 determines the
control function of logic input terminal VIA.
See page 91 for a complete list of VIA logic input assignments.
90 S1A53838 09/2011
I/O Control Parameters
Logic inputs F, R, RES, and VIA (if parameter [VIA selection] (F109) is set to 1 or 2) can be set to the functions
described in the table below. See table on page 97 for logic input function compatibility.
Function Action
No. Description
0 [No assigned] No function Logic input disabled
assigned
1 [Run permissive] OFF: drive motor output disabled, motor coasts to stop
(see also input function ON: drive ready for operation
54, page 95) If [Logic Funct 2 active] (F110) is not set to 1 [Run permissive], a logic input should
be assigned to the [Run permissive] logic function to enable the motor to start.
2 [Forward] Mode Logic Input Action
2-wire control OFF: Motor ramps down to a stop
(2-wire control: input
ON: Motor runs forward
function 49 NOT used)
or Mode Stop Input Logic Input Action
(3-wire control: input State
function 49 USED)
3-wire control OFF OFF: no function
ON: no function
3-wire control ON OFF to ON transition starts the drive, motor runs
forward
3 [Reverse] Mode Logic Input Action
2-wire control OFF: Motor ramps down to a stop
(2-wire control: input func-
ON: Motor runs reverse
tion 49 NOT used)
or Mode Stop Input Logic Input Action
(3-wire control: input State
function 49 USED)
3-wire control OFF OFF: no function
ON: no function
3-wire control ON OFF to ON transition starts the drive, motor runs
in reverse
5 [Acc / Dec] OFF: Acceleration/deceleration pattern 1
ON: Acceleration/deceleration pattern 2
6 [PS1] Input 3 Input 2 Input 1 Motor Speed
Preset speed command
0 0 0 minimum speed or speed refer-
input 1
ence per [Frequency mode sel]
(FMOd)
0 0 1 Sr1: preset speed 1
7 [PS2] 0 1 0 Sr2: preset speed 2
Preset speed command
0 1 1 Sr3: preset speed 3
input 2
1 0 0 Sr4: preset speed 4
8 [PS3] 1 0 1 Sr5: preset speed 5
Preset speed command
1 1 0 Sr6: preset speed 6
input 3
1 1 1 Sr7: preset speed 7
10 [Fault reset] (see also
input function 55, page 95)
DANGER
UNINTENDED EQUIPMENT OPERATION
This configuration enables to reset the drive. Check this action will not endanger per-
sonnel or equipment in any way
Failure to follow these instructions will result in death or serious injury.
ON to OFF transition clears a detected fault (if cause of detected fault has been cleared)
11 [Ext Fault] (see also OFF: No external detected fault
input function 45, page ON: Motor stops according to method set by parameter [Ext. fault stop Mode] (F603)
94) Embedded display terminal displays E detected fault, detected fault relay activated
S1A53838 09/2011 91
I/O Control Parameters
Function Action
No. Description
13 [DC braking]
WARNING
NO HOLDING TORQUE
z DC injection braking does not provide any holding torque at zero speed.
z DC injection braking does not work when there is a loss of power or when the drive
detects a fault.
z Where necessary, use a separate brake to maintain torque levels.
Failure to follow these instructions can result in death, serious injury, or equip-
ment damage.
OFF: No DC braking command
ON: DC braking applied to motor,
Level and time set by parameters [DC braking current] (F251) and
[DC braking time] (F252)
14 [PID disable] OFF: PID control permitted
ON: PID control prohibited
PID control prohibited input terminal function is available to switch PID control and open-
loop control.
Also Clear PID integral value input terminal function (function 65) is available.
Note: For software version lower than V1.7IE04, when Clear PID integral value (function
65) and PID Control Prohibited (function 14) are used, it is necessary to set [Command
mode sel] (CMOd) to [Logic inputs] (O) Control terminal logic inputs.
15 [Param Edit] OFF: Parameters locked (if parameter F700 = 1)
Functional only when pa- ON: Programming changes permitted
rameter [Parameter lock]
(F700) = 1
16 [Run reset] OFF: drive motor output disabled, motor coasts to stop
ON: drive ready for operation
ON to OFF transition clears a detected fault (if cause of detected fault has cleared)
20 [FW-RMP2] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of forward ON: Motor runs forward,
run command and accel- ramping up per ACC/dEC pattern 2
eration/deceleration pat-
tern 2 selection
21 [Rev- RMP2] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of reverse ON: Motor runs in reverse, ramping up per ACC/dEC pattern 2
run command and accel-
eration/deceleration pat-
tern
2 selection
22 [FW, PS1] OFF: Motor ramps down to a stop
Combination of forward ON: Motor runs forward, at speed set by Sr1, preset speed 1
run command and preset
speed 1 command
23 [RV, PS1] OFF: Motor ramps down to a stop
Combination of reverse ON: Motor runs in reverse, at speed set by Sr1, preset speed 1
run command and preset
speed 1 command
24 [FW, PS2] OFF: Motor ramps down to a stop
Combination of forward ON: Motor runs forward, at speed set by Sr2, preset speed 2
run command and preset
speed 2 command
25 [RV, PS2] OFF: Motor ramps down to a stop
Combination of reverse ON: Motor runs in reverse, at speed set by Sr2, preset speed 2
run command and preset
speed 2 command
26 [FW, PS3] OFF: Motor ramps down to a stop
Combination of forward ON: Motor runs forward, at speed set by Sr3, preset speed 3
run command and preset
speed 3 command
92 S1A53838 09/2011
I/O Control Parameters
Function Action
No. Description
27 [RV, PS3] OFF: Motor ramps down to a stop
Combination of reverse ON: Motor runs in reverse, at speed set by Sr3, preset speed 3
run command and preset
speed 3 command
30 [FW-RMP2-SP1] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of forward ON: Motor runs forward, at speed set by Sr1, preset speed 1,
run command, preset ramping up per ACC/dEC pattern 2
speed 1 command, and
acceleration/deceleration
pattern 2 selection
31 [Rev-RMP2-SP1] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of reverse ON: Motor runs in reverse, at speed set by Sr1, preset speed 1,
run command, preset ramping up per ACC/dEC pattern 2
speed 1 command, and
acceleration/deceleration
pattern 2 selection
32 [FW-RMP2-SP2] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of forward ON: Motor runs forward, at speed set by Sr2, preset speed 2,
run command, preset ramping up per ACC/dEC pattern 2
speed 2 command, and
acceleration/deceleration
pattern 2 selection
33 [Rev-RMP2-SP2] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of reverse ON: Motor runs in reverse, at speed set by Sr2, preset speed 2,
run command, preset ramping up per ACC/dEC pattern 2
speed 2 command, and
acceleration/deceleration
pattern 2 selection
34 [FW-RMP2-SP3] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of forward ON: Motor runs forward, at speed set by Sr3, preset speed 3,
run command, preset ramping up per ACC/dEC pattern 2
speed 3 command, and
acceleration/deceleration
pattern 2 selection
35 [Rev-RMP2-SP3] OFF: Motor stops, ramping down per ACC/dEC pattern 2
Combination of reverse ON: Motor runs in reverse, at speed set by Sr3, preset speed 3,
run command, preset ramping up per ACC/dEC pattern 2
speed 3 command, and
acceleration/deceleration
pattern 2 selection
38 [Frequency source] OFF: drive follows speed reference set by parameter [Frequency mode sel] (FMOd)
Frequency reference ON: drive follows speed reference set by parameter [Remote spd ref 2] (F207) >
source switching (if [Auto/man speed ref] (F200) = 1)
39 [Motor switch]
CAUTION
RISK OF DAMAGE TO THE MOTOR
z The motor switching function disables motor thermal protection.
z The use of external overload protection is required when using motor switching.
Failure to follow these instructions can result in death, serious injury, or equip-
ment damage.
S1A53838 09/2011 93
I/O Control Parameters
Function Action
No. Description
40 [Mot param. switch]
Motor control parameter
switching V/Hz, current
CAUTION
limit, acceleration/decel- RISK OF DAMAGE TO THE MOTOR
eration pattern z The parameter switching function disables motor thermal protection.
z The use of external overload protection is required when using motor switching.
Failure to follow these instructions can result in death, serious injury, or equip-
ment damage.
DANGER
LOSS OF PERSONNEL AND EQUIPMENT PROTECTION
When F650 is set to 1 or 2 and a logic input set to function "52" is activated, all the
drive controller protection will be disable.
Logic input should not be enable on function 52 for typical applications...
Logic input should be enable on function 52 only in extraordinary situations where
a thorough risk analysis demonstrates that the presence of adjustable speed drive
protection poses a greater risk than personnel injury or equipment damage.
Failure to follow these instructions will result in death or serious injury.
This function enables the "Forced fire" mode.
In this mode, all the detected fault will be ignored or if it is a hardware trip, the drive will
be reset to try to restart.
OFF: No function
ON: Motor runs at speed set by F294
Note: F650, F659 and F294 must be configured to activate this function.
94 S1A53838 09/2011
I/O Control Parameters
Function Action
No. Description
53 [Fire mode] This function enables the "Fire" mode
OFF: No function
ON: Motor runs at speed set by F294
Note: F650, F659 and F294 must be configured to activate this function.
54 [Inverse Run permis.] OFF: drive ready for operation
Inversion of run permis- ON: drive motor output disabled, motor coasts to stop
sive (see also input func- This mode allows to have a freewheel stop using a terminal command.
tion 1 page 91)
55 [Inv fault reset]
Inversion of clear detect-
ed fault (see also input
DANGER
function 10 page 91) UNINTENDED EQUIPMENT OPERATION
This configuration enables to reset the drive. Check this action will not endanger per-
sonnel or equipment in any way
Failure to follow these instructions will result in death or serious injury.
OFF to ON transition clears a detected fault (if cause of detected fault has been cleared)
56 [Run, FW] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs forward
missive and run forward
command (2-wire control
only)
57 [Run, RV] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs reverse
missive and run reverse
command (2-wire control
only)
61 [I limit 1/2] OFF: Current limit level 1 [Motor Current Limit] (F601) selected
Current limit level selec- ON: Current limit level 2 [Mot. 2 current limit] (F185) selected
tion
62 [RY on] OFF: Normal real-time relay operation
Holding of RYA-RYC ON: RYA-RYC is held on once activated
relay output
64 [Cancel HMI cmd] OFF: Last graphic display option command cancelled
Cancellation of last ON: Last graphic display option command retained
graphic display option
command
65 [PID integral] OFF: No action
Clear PID integral value ON: PID integral value held at zero
66 [Run-fw-sp1] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs forward at speed set by Sr1, preset speed 1
missive, run forward com-
mand, and preset speed 1
command
67 [Run-rev-sp1] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs reverse at speed set by Sr1, preset speed 1
missive, run reverse com-
mand, and preset speed 1
command
68 [Run-fw-sp2] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs forward at speed set by Sr2, preset speed 2
missive, run forward com-
mand, and preset speed 2
command
69 [Run-rev-sp2] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs reverse at speed set by Sr2, preset speed 2
missive, run reverse com-
mand, and preset speed 2
command
S1A53838 09/2011 95
I/O Control Parameters
Function Action
No. Description
70 [Run-fw-sp4] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs forward at speed set by Sr4, preset speed 4
missive, run forward com-
mand, and preset speed 4
command
71 [Run-rev-sp4] OFF: drive motor output disabled, motor coasts to stop
Combination of run per- ON: Motor runs reverse at speed set by Sr4, preset speed 4
missive, run reverse com-
mand, and preset speed 4
command
72 [PID rev] OFF: if F111 = 72 and F terminal is OFF, PI error input = reference - feedback
PID error signal reversed ON: if F111 = 72 and F terminal is ON, PI error input = feedback - reference
73 [Damper feedBack] OFF: if F111 or F112 or F113 is not set to 73 the damper has no effect.
ON: if F111 or F112 or F113 = 73 the damper is ON.
The damper feedback has not effect if not configured to an output.
96 S1A53838 09/2011
I/O Control Parameters
O = Compatible
X = Incompatible
+ = Compatible under some conditions
@ = Priority
Function No. / Function 1/54 2 3 5 6-9 10/55 11/45 13 14 15 46/47 48 41-43 49 38 39 40 52/53
2 [Forward] + X O O O X X O O X O O X O O O X
3 [Reverse] + + O O O X X O O X O O X O O O X
5 [Acc / Dec] + O O O O X X O O X O O O O O X O
6~8 [PS1]~[PS3] + O O O O X X O O X O O O O O O X
13 [DC braking] + @ @ @ @ O X @ O X O @ @ O O O X
14 [PID disable] O O O O O O X X O X O O O O O O X
15 [Param Edit] O O O O O O O O O O O O O O O O O
48 [Forced local] O O O O O O O O O O O O O O O O X
[(+) speed]
41-43 O O O O O O O O O O O O O O O O X
[(-) speed] [+/- clear]
49 [3-wire] + @ @ O O O X X O O X O O O O O X
38 [Frequency source] O O O O O O O O O O O O O O O O X
39 [Motor switch] O O O O O O O O O O O O O O O X O
The following logic input functions are active, regardless of the [Frequency mode sel] (FMOd) and [Command
mode sel] (CMOd) setting.
z (1) Run permissive
z (10) Clear detected fault
z (11) External detected fault
When determining function compatibility using the table above, the function listed horizontally is activated first
and the function listed vertically is activated second.
S1A53838 09/2011 97
I/O Control Parameters
0 [Low speed reach] OFF: output frequency is low speed setting [Low limit frequency] (LL)
Low speed reached ON: output frequency is > low speed setting LL
1 [Inv low spd reach] OFF: output frequency is > low speed setting [Low limit frequency] (LL)
Inversion of low speed reached ON: output frequency is low speed setting LL
2 [High speed reach] OFF: output frequency is < high speed setting [Upper limit freq] (UL)
High speed reached ON: output frequency is high speed setting UL
3 [Inv Hi spd reach] OFF: output frequency is high speed setting [Upper limit freq] (UL)
Inversion of high speed reached ON: output frequency is < high speed setting UL
4 [F100 speed reach] OFF: output frequency is < [Freq. 1 reached] (F100) speed setting
F100 speed reached (See page ON: output frequency is F100 speed setting
114 for more details on parameter
F100)
5 [Inv F100 sp reach] OFF: output frequency is [Freq. 1 reached] (F100) speed setting
Inversion of F100 speed reached ON: output frequency is < F100 speed setting
6 [Speed reach] OFF: output frequency is commanded speed +/- [Freq.2 bandw.] (F102)
Commended speed reached hysteresis band
ON: output frequency is > commanded speed +/- F102 hysteresis band
7 [Inv speed reach] OFF: output frequency is > commanded speed +/- [Freq.2 bandw.]
Inversion of commanded speed (F102) hysteresis band
reached ON: output frequency is commanded speed +/- F102 hysteresis band
8 [F101 speed reach] OFF: output frequency is [Freq. 2 reached] (F101) speed +/- [Freq.2
F101 speed reached (See page bandw.] (F102) hysteresis band
114 for more details on parameters ON: output frequency is > F101 speed +/- F102 hysteresis band
F101 and F102.)
9 [Inv F101 sp reach] OFF: output frequency is > [Freq. 2 reached] (F101) speed +/- [Freq.2
Inversion of F101 speed reached bandw.] (F102) hysteresis band
ON: output frequency is F101 speed +/- F102 hysteresis band
12 [Overload flt] OFF: Estimated motor torque has NOT been at [Overtorque level]
Overtorque fault (F616) level for a time period longer than that set by [Ovtorque det
Overtorque fault detection is active time] (F618)
only if parameter F615 = 1. See ON: Estimated motor torque has been at F616 level for a time period
page 132 for more detail on an longer than that set by F618. drive stopped, displaying Ot
overtorque detected fault and
parameters F616 and F618.)
13 [Inv overload flt] OFF: Estimated motor torque has been at [Overtorque level] (F616)
Inversion of Overload flt function level for a time period longer than that set by [Ovtorque det time]
(F618). drive stopped, displaying Ot
ON: Estimated motor torque has NOT been at F616 level for a time
period longer than that set by F618
98 S1A53838 09/2011
I/O Control Parameters
15 [Drive no run] OFF: drive is powering the motor, accelerating, decelerating, at constant
Inversion of Drive no run function speed, or DC braking
ON: drive is not powering the motor
16 [Motor overload] OFF: motor thermal state is < 50% of motor overload detected fault level
Motor overload alarm detection is only ON: motor thermal state is 50% of motor overload detected fault level
active if parameter OLM is set to
either 0, 1, 4, or 5. See page 135 for
more detail on motor overload
protection settings.
17 [Inv mot. overload] OFF: motor thermal state is 50% of motor overload detected fault level
Inversion of Motor overload function ON: motor thermal state is < 50% of motor overload detected fault level
20 [Torque alarm] OFF: Estimated motor torque is < 70% of F616 level minus F619
Overtorque alarm detection is active hysteresis band
only if parameter F615 = 0. See ON: Estimated motor torque is 70% of F616 level
page 132 for more detail on the over-
torque alarm and parameters [Over-
torque level] (F616), [Overtorque
band] (F619).
21 [Inv torque alarm] OFF: Estimated motor torque is 70% of [Overtorque level] (F616) level
Inversion of Torque alarm function ON: Estimated motor torque is < 70% of F616 level minus
[Overtorque band] (F619) hysteresis band
22 [Gen. alarm] OFF: No detected fault condition from the sources listed below exists
General alarm ON: A detected fault has been issued by one of the following sources:
Overtorque detected fault (output functions 12 and 13)
Motor overload (output functions 16 and 17)
Overtorque detected fault (output functions 20 and 21)
Load detection loss (output functions 24 and 25)
Run time (output functions 42 and 43)
Undervoltage (output functions 54 and 55)
drive in sleep mode (see for more detail on parameter F256)
Power loss (see for more detail on parameter F302)
Overcurrent motor current limit level (parameter F601)
Overvoltage DC bus voltage overvoltage stall level (parameter
F626)
Drive overheating
23 [Inv gen. alarm] OFF: A detected fault has been issued by one of the following sources:
Inversion of General alarm function Overtorque detected fault (output functions 12 and 13)
Motor overload (output functions 16 and 17)
Overtorque detection loss (output functions 20 and 21)
Failure of load detection (output functions 24 and 25)
Run time (output functions 42 and 43)
Undervoltage (output functions 54 and 55)
Drive in sleep mode (see for more detail on parameter F256)
Power loss (see for more detail on parameter F302)
Overcurrent motor current limit level (parameter F601)
Overvoltage DC bus voltage overvoltage stall level (parameter
F626)
drive overheating
ON: No alarm condition from the sources listed above exists
24 [Underload detect.] OFF: Motor current is greater than F611 level + F609 hysteresis band
(See page 130 for more detail on pa- ON: Motor current is less than F611 level for the time set by F612
rameters F609 F612 and the
underload function.)
25 [Inv underl. det.] OFF: Motor current is less than F611 level for the time set by F612
Inversion of Underload detect. func- ON: Motor current is greater than F611 level + F609 hysteresis band
tion
S1A53838 09/2011 99
I/O Control Parameters
26 [Manu reset flt.] OFF: None of the detected fault conditions listed below exist
Non-autoresettable detected fault ON: One (or more) of the following detected fault conditions exists and has
stopped the drive:
E external detected fault
E-18 VIA analog input signal detected fault
E-19 main control board CPU communication
E-20 excessive torque boost
E-21 main control board CPU detected fault 2
EEP1 main control board EEPROM detected fault 1
EEP2 main control board EEPROM detected fault 2
EEP3 main control board EEPROM detected fault 3
EF2 ground detected fault
EPH0 output phase detected fault detection
EPH1 input phase detected fault detection
Err1 speed reference
Err2 main control board RAM
Err3 main control board ROM
Err4 main control board CPU detected fault 1
Err5 serial communication control
Err7 motor current sensor
Err8 serial communication network
Err9 graphic display option communication interruption
Etn1 auto-tuning
EtYP drive ratings
OCA short-circuit detected in drive output inverter stage
during motor startup
OCL short-circuit detected in motor or output wiring during
motor startup
OH2 - external overheating
Ot overtorque
Uc underload
UP1 - Undervoltage
27 [Inv manu reset flt.] OFF: One (or more) of the following fault conditions exists and has stopped
Inversion of Manu reset flt. function the drive:
E external detected fault
E-18 VIA analog input signal
E-19 main control board CPU communication
E-20 excessive torque boost
E-21 main control board CPU detected fault 2
EEP1 main control board EEPROM detected fault 1
EEP2 main control board EEPROM detected fault 2
EEP3 main control board EEPROM detected fault 3
EF2 ground fault
EPH0 output phase loss detection
EPH1 input phase loss detection
Err1 speed reference
Err2 main control board RAM
Err3 main control board ROM
Err4 main control board CPU detected fault 1
Err5 serial communication control
Err7 motor current sensor
Err8 serial communication network
Err9 graphic display option communication interruption
Etn1 auto-tuning
EtYP drive ratings
OCA short-circuit detected in drive output inverter stage
during motor startup
OCL short-circuit detected in motor or output wiring during
motor startup
OH2 - external overheating
Ot overtorque
Uc underload
UP1 - Undervoltage
28 [Auto-reset fault] OFF: None of the detected fault conditions listed below exist
Auto-clear detected fault ON: One (or more) of the following detected fault conditions exists:
Fd1 damper detected fault 1 (closed damper)
Note: Relay activates when Fd2 damper detected fault 2 (opened damper)
maximum number of autoclear set OC1 overcurrent during acceleration
by [Number auto reset] (F303) OC2 overcurrent during deceleration
page 124 is reached. OC3 overcurrent during constant speed
OC1P Short circuit or ground detected fault during
acceleration
OC2P Short circuit or ground detected fault during
deceleration
OC3P Short circuit or ground detected fault during constant
speed
OH drive overheating
OL1 drive overload
OL2 motor overload
OP1 overvoltage during acceleration
OP2 overvoltage during deceleration
OP3 overvoltage during constant speed
29 [Inv auto-reset flt] OFF: One (or more) of the following detected fault conditions exists:
Inversion of Auto-reset fault function Fd1 damper detected fault 1 (closed damper)
Fd2 damper detected fault 2 (opened damper)
Note: Relay deactivates when OC1 overcurrent during acceleration
maximum number of autoclear set OC2 overcurrent during deceleration
by [Number auto reset] (F303) OC3 overcurrent during constant speed
page 124 is reached. OC1P Short circuit or ground detected fault during
acceleration
OC2P Short circuit or ground detected fault during
deceleration
OC3P Short circuit or ground detected fault during constant
speed
OH drive overheating
OL1 drive overload
OL2 motor overload
OP1 overvoltage during acceleration
OP2 overvoltage during deceleration
OP3 overvoltage during constant speed
31 [Inv drive rdy 1] OFF: drive ready for operation (ready includes active run permissive and
Inversion of Drive rdy 1 function active run command)
ON: drive not ready for operation
33 [Inv drive rdy 2] OFF: drive ready for operation (ready does not include active run permis-
Inversion of Drive rdy 2 function sive or active run command)
ON: drive not ready for operation
34 [VIB ref source] OFF: analog input terminal VIB is NOT the active speed reference source
VIB input reference source ON: VIB is the active speed reference source
35 [Inv VIB ref source] OFF: analog input terminal VIB is the active speed reference source
Inversion of VIB ref source function ON: VIB is NOT the active speed reference source
36 [Fault relay]
(The drive is not in a fault state during
auto clear detected fault attempts.
WARNING
See also function 10 page 98) LOSS OF CONTROL
z When F130, F132, F137 is set to 36, the output will be active
when the drive will detect a fault.
z The drive status will not be detected if the wiring is damaged for any
reason.
z Do not select 36 unless you are sure that your signal will be present
in any case.
Failure to follow these instructions can result in death, serious inju-
ry, or equipment damage.
38 [Ser. data relay FL] OFF: Serial communication word FA50 bit 0 = 0
Serial communication data ON: Serial communication word FA50 bit 0 = 1
39 [Inv ser. dat rel. FL] OFF: Serial communication word FA50 bit 0 = 1
Inversion of ser. dat rel. FL function ON: Serial communication word FA50 bit 0 = 0
40 [Ser. data relay RY] OFF: Serial communication word FA50 bit 1 = 0
Serial communication data ON: Serial communication word FA50 bit 1 = 1
41 [Inv ser. dat rel RY] OFF: Serial communication word FA50 bit 1 = 1
Inversion of ser. dat rel. RY function ON: Serial communication word FA50 bit 1 = 0
42 [Drive run time al] OFF: Run time is < F621 time setting
Drive operational run time alarm ON: Run time is F621 time setting
(see page 120 for more detail on
parameter F621).
43 [Inv.drive run time al] Inversion of Drive OFF: Run time is F621 time setting
run time al function ON: Run time is < F621 time setting
44 [Drive serv. alarm] OFF: drive maintenance detected fault not active
Drive service alarm (see page 133 ON: drive maintenance detected fault active
for more detail on parameter
F634).
45 [Inv. drive serv. alarm] Inversion of OFF: drive maintenance detected fault active
Drive serv. alarm function ON: drive maintenance detected fault not active
52 [Speed ref = VIA] OFF: Speed reference from the source identified by
Drive speed reference equals VIA sig- [Frequency mode sel] (FMOd) or the source identified by
nal [Remote spd ref 2] (F207) VIA signal
ON: Speed reference from the source identified by FMOd or the source
identified by F207 = VIA signal
53 [Inv. speed ref = VIA] Inversion of OFF: Speed reference from the source identified by
Speed ref = VIA function [Frequency mode sel] (FMOd) or the source identified by
[Remote spd ref 2] (F207) = VIA signal
ON: Speed reference from the source identified by FMOd or the source
identified by F207 VIA signal
55 [Inv. undervolt. alarm] Inversion of Un- OFF: Undervoltage detected fault is active
dervolt. al. function ON: Undervoltage detected fault is not active
57 [Inv. loc / remote] Inversion of Loc / re- OFF: drive is in local mode
mote function ON: drive is in remote mode
58 [PTC alarm] OFF: Motor temperature as indicated by PTC thermal probes is < 60% of
PTC thermal alarm the detected fault level
ON: Motor temperature as indicated by PTC thermal probes is 60% of the
detected fault level
59 [Inv. PTC alarm] Inversion of PTC OFF: Motor temperature as indicated by PTC thermal probes is 60% of the
alarm function detected fault level
ON: Motor temperature as indicated by PTC thermal probes is < 60% of the
detected fault level
60 [Speed ref = VIB] OFF: Speed reference from the source identified by
Drive speed reference equals VIB sig- [Frequency mode sel] (FMOd) or the source identified [Remote spd ref 2]
nal (F207) VIB signal
ON: Speed reference from source identified by FMOd or the source iden-
tified F207 = VIB signal
61 [Inv. speed ref = VIB] Inversion of OFF: Speed reference from source identified by
Speed ref = VIB function [Frequency mode sel] (FMOd) or the source identified [Remote spd ref 2]
(F207) = VIB signal
ON: Speed reference from the source identified by FMOd or the source
identified F207 VIB signal
62 [VIA detection] ON: The value of VIA is equal to or higher than F160 + F161
Analog VIA detection OFF: The value of VIA is equal to or lower than F160 - F161
63 [Inv. VIA detection] Inversion of VIA ON: The value of VIA is equal to or lower than F160 - F161
detection function OFF: The value of VIA is equal to or higher than F160 + F161
64 [VIB detection] ON: The value of VIB is equal to or higher than F162 + F163
Analog VIB detection OFF: The value of VIB is equal to or lower than F162 - F163
65 [Inv. VIB detection] Inversion of VIB ON: The value of VIB is equal to or lower than F162 - F163
detection function OFF: The value of VIB is equal to or higher than F162 + F163
66 [Freq. reach hyst] ON: The ouptput frequency is equal to or higher than F101 + F102
Set frequency attainment signal with OFF: The ouptput frequency is equal to or lower than F101 - F102
hysteresis (See page 114 for more detail on parameters F101 and F102.)
67 [Inv. freq. reach hyst] Inversion of ON: The ouptput frequency is equal to or lower than F101 - F102
Freq. reach hyst function OFF: The ouptput frequency is equal to or higher than F101 + F102
(See page 114 for more detail on parameters F101 and F102.)
General
z The selection of VIA or VIB as the speed reference input in remote mode is made through parameters
[Frequency mode sel] (FMOd) and [Remote spd ref 2] (F207). FMOd is the primary speed reference
source, while F207 is the secondary source. Switching between the two is determined by the setting of
parameter [Auto/man speed ref] F200. For more information, see page 108.
z Analog output terminal FM can be configured to provide a signal in proportion to the VIA or VIB signal levels.
See parameter FMSL, selections 13 and 14, on page 108.
z When PID control is enabled, VIA or VIB can serve as the setpoint input. Either VIA or VIB needs to be
selected as the feedback input. See page 110 for more information on parameter F360 and PID control.
z Information can be transferred between the serial communication network and the analog inputs via read and
write functions F870, F871, and F875-F879. For more information, see pages 140 to 141.
F204
F202
Speed Reference %
F201 F203 20 mA
or
10 V
A further refinement of the bias and slope of the analog input signals can be made with parameters F470
F473.
F202 [VIA freq. point 1] VIA output frequency level 1 0.0 to 200.0 Hz 0.0 Hz
F203 [VIA ref point 2] VIA speed reference level 2 0 to 100% 100%
F204 [VIA freq. point 2] VIA output frequency level 2 0.0 to 200.0 Hz 50.0 Hz
F160 [VIA rel thresh. logic] Threshold logic for relay link to VIA 0 to 100% 0%
F161 [VIA threshold hyst.] Hysteresis threshold for logic relay link to VIA 0 to 20% 3%
F211 [VIB freq. point 1] VIB output frequency level 1 0.0 to 200.0 Hz 0.0 Hz
F212 [VIB ref. point 2] VIB speed reference level 2 0 to 100% 100%
F213 [VIB freq. point 2] VIB output frequency level 2 0.0 to 200.0 Hz 50.0 Hz
F162 [VIB rel thresh. logic] Threshold logic for relay link to VIB 0 to 100% 0%
F163 [VIB threshold hyst.] Hysteresis threshold for logic relay link to VIB 0 to 20% 3%
DANGER
UNINTENDED EQUIPMENT OPERATION
If the input bias level is set too high, the drive will start the motor without a signal present at VIA or VIB.
Failure to follow these instructions will result in death or serious injury.
DANGER
UNINTENDED EQUIPMENT OPERATION
If the input bias level is set too high, the drive will start the motor without a signal present at VIA or VIB.
Failure to follow these instructions will result in death or serious injury.
Large
,
Output frequency Hz
Maximum frequency
Smaller
Large
Default Setting
,
Smaller
0 %
0% 100%
0V 10 Vdc
0(4) mA 20 mAdc
Speed Reference Signal (VIA, VIB Input Value)
Parameters [VIA bias] (F470) and [VIB bias] (F472) are factory set so that a minimal signal needs to be
applied to VIA or VIB before the drive starts the motor.
z To increase the signal level required to start the motor, decrease the input bias level.
z To reduce the signal level required to start the motor, increase the input bias level.
DANGER
UNINTENDED EQUIPMENT OPERATION
If the input bias level is set too high, the drive will start the motor without a signal present at VIA or VIB.
Failure to follow these instructions will result in death or serious injury.
Parameters [VIA gain] (F471) and [VIB gain] (F473) are factory set so that the drive output reaches rated
voltage and frequency just before the signal to VIA or VIB reaches its maximum level.
z To decrease the signal level required before the drive output reaches rated voltage and frequency, increase
the input gain level.
z To increase the signal level required before the drive output reaches rated voltage and frequency, decrease
the input gain level.
Note: If the input gain level is set too low, the drive output may never reach rated voltage and frequency.
0 [Enable]
1 [Disable]
Switching between two speed reference sources by means of a logic input is enabled if parameter F200 is set to 0.
To use this function, you need to assign a logic input to function 38, Auto/Man speed ref.
When the assigned logic input is off, the drive will follow the speed reference source defined by parameter [Frequency mode sel]
(FMOd) (see page 77).
When the assigned logic input is on, the drive will follow the speed reference source defined by parameter [Remote spd ref 2]
(F207) (see page 78).
When parameter F200 is set to 1, the drive will follow the FMOd speed reference source when it is operating above 1 Hz.
Below 1 Hz, it will follow the F207 speed reference source.
Parameter FM is used to match the FM terminal output signal with the input requirements of the attached panel meter by adjust-
ing the slope and bias of the analog output signal. Before adjusting FM, set [AO funct. selection] (FMSL) to either 15 or 17.
As you adjust the value of FM, monitor the display on the attached panel meter. When the meter display reaches 100%, press
the ENT key on the drive embedded display terminal. The drive will flash between FM and the adjusted value, indicating that the
adjustment has been saved.
Factory set-
Code Name / Description Adjustment range
ting
0 [Negative slope]
1 [Positive slope]
Refer to the diagram below for examples of adjusting parameters [AO scaling] (FM), [AO slope] (F691), and F692.
= , = = , =
(mA) (mA)
20 20
Output Current
Current
Output
4
0
0 100% 0 100%
FMSL signal value FMSL signal value
= , = = , =
(mA) (mA)
20 20
Output Current
Current
Output
:Large Gain :Small Gain
4
0
0 100% 0 100%
FMSL signal value FMSL signal value
F694 [Freq. for AO = 0V] Low frequency when analog output equal 0 V 0 Hz to [Max frequency] 0 Hz
(FH) Hz
Refer to the diagram below for adjusting parameters F694, and [Freq. for AO = 10V] (F695).
10 V 10 V
0V 0V
F694 F695 F695 F694
Speed reference Speed reference
Motor frequency Motor frequency
Internal reference (after PID) Internal reference (after PID)
F695 [Freq. for AO = 10V] High frequency when analog output equal 10 V 0 Hz to [Max frequency] 0 Hz
(FH) Hz
Refer to the diagram above for adjusting parameters [Freq. for AO = 0V] (F694), and F695.
F130 [RY Relay Function 1] RYA-RYC Relay Function 0 to 69, 254, 255 4
For a complete description of the various functions assignable to the RYA-RYC relay, see page 98.
The RYA-RYC relay can have a secondary assignment with programmed selection logic. See parameters
[RY Relay Function 2] (F137) and [RY logic select.] (F139) on page 113 for more detail.
F146 [RY delay] Delay for RYA-RYC Relay 0.0 to 60.0 s 0.0 s
For a complete description of the various functions assignable to the FL relay, see page 98.
Factory set-
Code Name / Description Adjustment range
ting
F147 [FL Relay delay] Delay for FL Relay 0.0 to 60.0 s 0.0 s
Parameter F362 adjusts the proportional gain applied during PID control. The speed change applied to the motor is a correc-
tional value proportional to the product of this parameters setting and the process error (deviation between the setpoint and the
feedback value).
A higher setting of F362 provides a fast response to a process error but may also result in instability such as hunting. The
diagram below illustrates the effect produced by adjusting F362.
Feedback
Amount
Fast Response
(F362 = Large Gain)
Slow Response (F362= Small Gain)
Time
Parameter F363 adjusts the integral gain applied during PID control. Any residual process errors that remain after correction
by the proportional gain are cleared to zero over time by the integral gain function.
A higher setting of F363 provides a fast response to a process error but may also result in instability such as hunting. The
diagram below illustrates the effect produced by adjusting F363.
(F363= Small Gain)
Feedback Amount
Residual Deviation
Time
The integral gain value can be set to zero by setting a logic input to function 65. For more information, see table on page 91 and
parameters [LI F selection] (F111), [LI R selection] (F112), [LI RES selection] (F113), page 90, and
[VIA LI selection] (F118), page 90.
Factory set-
Code Name / Description Adjustment range
ting
Parameter F366 adjusts the derivative gain applied during PID control. This gain adjusts the response time of the drive to rapid
changes in the process.
Increasing the setting of F366 more than necessary may cause great fluctuations in motor speed resulting in system instability.
The diagram below illustrates the effect produced by adjusting F366.
Current Error
Previous
Error
Feedback Motor Speed Change
Amount
F359 [PID ctrl wait time] PID Control Waiting Time 0 to 2400 s 0
If parameter F359 is set to a value greater than 0 seconds, the drive will not immediately enter PID control upon startup. For
the time set by F359, the drive will ignore the feedback signal, accelerating the motor to the speed set by the reference input.
This function can be used to help prevent the drive from entering PID control mode before the system approaches the final op-
erating level.
0 [No]
1 [Yes]
F392 [PID wake up (thres)] PI wake up threshold on PI error 0.0 to [Max frequency] 0.0 Hz
(FH)
DANGER
UNINTENDED EQUIPMENT OPERATION
Check that unintended restarts will not endanger personnel or equipment in any way.
Failure to follow these instructions will result in death or serious injury.
F393 [PID wake up, feedb] PI wake up threshold on PI feedback error 0.0 to [Max frequency] 0.0 Hz
(FH)
DANGER
UNINTENDED EQUIPMENT OPERATION
Check that unintended restarts will not endanger personnel or equipment in any way.
Failure to follow these instructions will result in death or serious injury.
0 [Disabled]
1 [Enabled fault] (detected fault mode). If F645 is set to 1 and the PTC probe exceeds a given, threshold, the drive will trip and
display an [PTC overheating] (OH2) code.
2 [Enabled alarm] (alarm mode). If F645 is set to 2 and the PTC probe exceeds a given, threshold, the drive will signal a de-
tected fault and continue operating.
Setting parameter F645 to 1 or 2 converts control terminal VIB into a PTC motor thermal probe input. See the ATV212 Instal-
lation manual, for wiring details.
Factory set-
Code Name / Description Adjustment range
ting
Two logic input functions can be configured to be active. The logic input functions assigned to parameters [Logic
Funct 1 active] (F108) and [Logic Funct 2 active] (F110) will continuously affect drive operation. See table
beginning on page 91 for a list of available logic input functions.
If F110 is not set to 1 (logic function [Run permissive]), a logic input should be assigned to the [Run
permissive] logic function to enable the motor to start.
Preset Speeds
A maximum of seven preset speeds can be selected by 4 logic inputs (F, R, RES, or VIA). Preset speed control
is only active when the drive is in logic input control ([Command mode sel] (CMOd) = 0).
For one preset speed, assign a logic input to function 6.
For up to three preset speeds, use two logic inputs for functions 6 and 7.
For up to seven preset speeds, use three logic inputs for functions 6, 7, and 8.
Preset speed commands take priority over speed commands from any other source. For more information on
preset speeds, see page 91. See page 42, for wiring instructions and timing diagram.
Factory
Code Name / Description Adjustment range
setting
F264 [+speed LI resp time] +Speed Logic Input Response Time 0.0 to 10.0 s 0.1 s
Parameter F264 sets the maximum on-time of the logic input assigned to
(+) speed, limiting the speed increase, as defined by parameter [+speed freq. step] (F265), to only one step. Keeping the logic
input active longer than the time set by parameter F264 will allow multiple step increases of the speed command.
F265 [+speed freq. step] +Speed Frequency Steps 0.0 to [Max frequency] (FH) Hz 0.1 Hz
Parameter F265 sets the frequency width in Hz of each (+) speed command step.
F266 [- speed LI resp time] -Speed Logic Input Response Time] 0.0 to 10.0 s 0.1 s
Parameter F266 sets the maximum on-time of the logic input assigned to
(-) speed, limiting the speed decrease, as defined by parameter [-speed freq. step] (F267), to only one step. Keeping the logic
input active longer than the time set by parameter [+speed freq. step] (F265) will allow multiple step decreases of the speed
command.
F267 [- speed freq. step] -Speed Frequency Steps 0.0 to [Max frequency] (FH) Hz 0.1 Hz
Parameter F267 sets the frequency width in Hz of each (-) speed command step.
F268 [Init +/- Speed] Initial +/- Speed Command 0.0 to [Max frequency] (FH) Hz 0.0 Hz
Parameter F268 sets the +/- speed command in Hz that is applied to the drive when it is first powered up. Leaving this
parameter at its default value will result in the drives output frequency starting at 0 Hz every time it is powered up.
F269 [Init +/- Speed memo] Change of Initial +/- Speed Frequency - 1
0 [Disable]
1 [Enable]
The setting parameter F269 determines whether the value of parameter [Init +/- Speed] (F268) will change every time pow-
er is cycled to the drive. If parameter F269 is set to 1, parameter F268 will be set to the last speed command received by
the drive before power was removed.
F137 [RY Relay Function 2] RYA-RYC Relay Secondary Function 0 to 61, 254, 255 255
The RYA-RYC relay can be set to signal a secondary condition. The primary RYA-RYC relay function is set by parameter
[RY Relay Function 1] (F130) (see page 109). See table beginning on page 98 for a complete description of the primary and
secondary functions that can be assigned to the RYA-RYC relay.
0 [Function 1and 2]: [RY Relay Function 1] (F130) (primary) and [RY Relay Function 2] (F137) (secondary)
1 [Function 1 or 2]: F130 (primary) or F137 (secondary)
The RYA-RYC relay can be configured to energize when either:
Both the primary AND secondary conditions are met (true) (F139 = 0), or
Only one OR the other is met (true) (F139 = 1)
Factory
Code Name / Description Adjustment range
setting
F100 [Freq. 1 reached] Relay Output Frequency Level 1 Attained 0.0 to [Max frequency] (FH) Hz 0.0 Hz
The frequency set by parameter F100 is the threshold level for relay output functions 4 and 5 (see page 98).
Output Frequency (Hz)
Commanded
Frequency
Time (S)
0
ON
Relay Output Function 4 OFF
F101 [Freq. 2 reached] Relay Output Frequency Level 2 Attained 0.0 to [Max frequency] (FH) Hz 0.0 Hz
The frequency set by parameter F101 +/- the [Freq.2 bandw.] (F102) detection band is the threshold level for relay output
functions 8 and 9 and the hysteresis for relay output functions 66 and 67 (see page 103).
Output Frequency (Hz)
0 Time (S)
ON
Relay Output Function 8 OFF
Relay Output Function 9 ON
OFF
ON
Relay Output Function 66 OFF
F102 [Freq.2 bandw.] Frequency Attained Detection Band 0.0 to [Max frequency] (FH) Hz 2.5 Hz
Parameter F102 determines the bandwidth around the [Freq.2 reached] (F101) frequency (see diagram above) and the
commanded frequency (see diagram below) driving relay output functions 6 through 9 (see page 98).
+
Commanded Frequency
-
0 Time (S)
ON
Relay Output Function 6 OFF
Factory
Code Name / Description Adjustment range
setting
F167 [Freq band det range] Frequency bandwidth detection range 0.0 to [Max frequency] (FH) Hz 2.5 Hz
Parameter F167 determines the bandwidth around the VIA or VIB speed reference (see below) driving relay output functions
52, 53, 60, and 61 (see page 102).
This function can be used to signal whether the amount of processing and the amount of feedback agree when the PID function
is in use.
VIA
+
or
-
Time (S)
ON
Relay Output Function 52 + 60 OFF
F603 [Ext. fault stop Mode] External detected fault stop mode - 0
F604 [DC brk time ext flt] External Fault DC braking time 0.0 to 20.0 s 1.0 s
If parameter [Ext. fault stop Mode] (F603) is set to 2, parameter F604 will determine how long DC current will be
injected into the motor while the external fault logic input is active.
Damper control
This function applies to the ventilation ducts. The aim is to control the opening of the duct (shutter device called
a "damper") when the fan starts up.
Damper
ATV 212
Control Feedback
U V W 0 Rp P24 LIp
Flow of air
Damper Fan
open contact
Damper opening
M
3
Fan speed 1
0
t
Run command 1
0
t
Opening command 1
Rx
0
t
Open 1
Position of damper
Closed
0
F581 F582 t
0
t
Opening fault monitoring time delay. If the damper is not open at the end of the set time, the drive will lock in [Damper fault 1]
Fd1 detected fault mode. The timer is launch after the run command.
The time delay needs to be greater than the normal opening time of the damper.
Closing fault monitoring time delay. If the damper is not close at the end of the set time, the drive will lock in [Damper fault 2]
Fd2 detected fault mode. The timer is launch when the motor is stopped.
The time delay needs to be greater that the normal closing time of the damper
0 [No fault]
1 [Freewheel stop]
2 [Ramp stop]
The F583 parameter allows defining the behavior when [Damper fault 1] (Fd1) occurs.
Display Parameters
9
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Display parameters
0 [Motor frequency] Motor operating frequency (Hz or custom display), see [Customized freq val] (F702) on page 121.
1 [Reference] Speed reference (Hz or custom display), see F702 on page 121.
2 [I Mot] Motor current (% or A), see [Unit value selection] (F701) below.
3 [Drive rated I] Drive rated current (A)
4 [Drive therm state] (%)
5 [Motor power] Output power (kW)
6 [Int speed ref] Internal speed reference (after PID function) (Hz or custom display, see F702 on page 121.
7 [Com data] Serial communication data
8 [Motor speed] Output speed (rpm, see [Motor rated speed] (F417) on page 70)
9 [Com count] Displays the total number of frames received by the communication card since the last power ON
10 [Com count norm st.] Displays the total number of valid frames received by the communication card since the last power ON
The setting of parameter [Displayed param.] (F710) determines the default display on the drives embedded display terminal
upon power up.
Status alarms C, P, L, and H can only be displayed on the graphic display option if [Displayed param.] (F710) is set to 0. See
Run Mode on page 23 for more information.
0 [%]
1 [Amp or Volt]
The setting of parameter F701 determines how certain values will be displayed on the drive embedded display terminal, either
as a percentage of the drive rating or as a value of amperes or volts as appropriate.
The setting of F701 will only affect parameters and display values that can be represented in amperes or volts. This includes
the following parameters:
[Motor thermal prot.] (tHr) and F173: motor rated current
F251: DC braking current level
F185 and F601: motor current limit
F611: underload detection level
Motor rated voltage (parameters ulu and F171) are displayed in volts.
Parameter F708 works along with parameter [Loc. speed ref. step] (F707) (see page 77) to adjust the incremental steps of
the drive embedded display terminal frequency display.
At its factory setting, parameter F708 is disabled and the embedded display terminal increments or decrements frequency dis-
plays in 0.1 Hz steps.
If parameter F708 is set to a value other than 0, then the embedded display terminal frequency display is determined as fol-
lows: embedded display terminal frequency display = Internal speed reference (after PID function) x F708 / F707
For example, if both F707 and F708 are equal to 1, the embedded display terminal frequency display will increase only in
1 Hz steps.
Parameter F621 is used in conjunction with a relay output set to functions 42 or 43 (see page 102) to signal that the run time
specified by the setting of F621 has accumulated.
0.1 = 1 hour, 100 = 1000 hours
0 [Disable]
1 [Enable]
The setting of parameter F748 determines whether the drives accumulated power consumption memory, displayed in kilowatt-
hours (kWh), is cleared when the line power is cycled. If F748 is set to 0, the memory is cleared. If set to 1, the kWh memory
is retained.
0 [1 kWh]
1 [0.1 = 1 kWh]
2 [0.01 = 1 kWh]
3 [0.001 = 1 kWh]
The setting of parameter F749 determines the scaling of the kWh display on the embedded display terminal.
F702 [Customized freq val] Customized freq val 0.00 to 200.00 0.00
Parameters F702, F705, and F706 can be used to customize a speed display on the drive embedded display terminal
to match the applications operational speed, for example, feet per minute or units per hour.
0.00: Frequency displayed in Hz
0.0 If parameter F702 is set to a value other than 0.00, the frequency value displayed will be calculated as follows:
Value displayed = display or parameter frequency x F702. See example below.
1 to 200.0: Conversion factor
Hz
= =
X =
Hz
= =
X =
0 [Negative slope]
1 [Positive slope]
Parameter F705 sets the slope of the custom frequency display conversion. See the diagrams below for examples of the op-
eration of this function.
F706 [Customize unit bias] Custom Frequency Display Conversion Bias 0.00 to FH Hz 0.00 Hz
Parameter F706 adds a bias to the custom frequency display conversion process.
= , = = , =
graphic display graphic display
option option
800 1000
200
0 0
0 Output Frequency 80 (Hz) 0 Output Frequency 80 (Hz)
= , =
graphic display
option
800
0
0 Output Frequency 80 (Hz)
10
What's in this Chapter?
This chapter contains the following topics:
Topic Page
DANGER
UNINTENDED EQUIPMENT OPERATION
z The automatic restart can only be used on machines or installations which do not pose any danger to either personnel or
equipment.
z If the automatic restart is activated, the fault relay will only indicate a fault has been detected once the time-out period for the
restart sequence has expired.
z The equipment must be used in compliance with national and regional safety regulations
Failure to follow these instructions will result in death or serious injury.
0 Disabled.
1 to 10 Number of clear attempts.
Description
The table below lists the detected faults that can be cleared with Auto clear. If parameter F303 is set to a value greater than
0 and one of these detected faults occurs, the drive will attempt to automatically clear the detected fault, allowing it to be re-
started:
Fault detection codes that can be cleared with the automatic restart function after the cause has disappeared
Auto clear attempts will continue until the number of attempts set by parameter F303 has been exhausted.
If these attempts do not clear the detected fault condition, the drive will stop and a manual clear will be required.
If another type of detected fault occurs during the auto clear process, the drive will stop and a manual clear will
be required.
A successful auto clear means that the drive accelerates the motor to the commanded speed without another
detected fault occurring.
If an unspecified period of time elapses after a successful auto clear attempt without another detected fault
occurring, the reset attempt counter will clear allowing another full set of reset attempts to be made during a
future detected fault occurrence.
During the auto clear process, the drive embedded display terminal alternately displays rtrY and the display
value selected by parameter [Displayed param.] (F710), page 120.
Time delay
The first clear is attempted 1 second after the detected fault occurs. Each subsequent clear attempt adds 1
second to the time interval, as illustrated in the table below.
If catch-on-the-fly motor starting is enabled (parameter F301 is not set to 0), the drive will detect the motors
rotating direction and speed before applying power. This will result in a smooth reapplication of power to a
coasting motor without high current or torque pulses.
If F301 is disabled and the drive is started into a spinning motor, it will apply a low starting frequency to the
motor, operating in current limit until the motor almost stops. Then, the drive will accelerate the motor to the
commanded speed.
Catch-on-the-fly motor starting will be applied if F301 is set to 1 or 3 and:
z There is a brief power loss (the embedded display terminal does not go blank) that results in the drive
removing power from the motor,
z and, there is a continuous run command to the drive (2-wire control)
F301 Set to 1 or 3
Inout Voltage
Motor Speed
Run Command ON
OFF
F301 Set to 2 or 3
Motor Speed
ON
Run Command OFF
ON
Run Permissive OFF
If F301 is set to 4, the drive will perform a motor speed and direction search each time it receives a run
command.
Note: Enabling catch-on-the-fly adds about 300 milliseconds to implementation of each start command to the
drive.
Do not use catch-on-the-fly if there is more than one motor supplied by the drive.
0 [Disable]
1 [Brief power loss] After brief power loss
2 [Run restored] After run permissive is restored
3 [Power loss, run] After brief power loss or run permissive is restored
4 [Each start] During every startup
0 [Disabled] Cleared
If parameter F632 is set to 0, the drives memory of the motors thermal state (used for overload calculation) is cleared when-
ever the power is cycled.
1 [Enabled] Retained
If parameter F632 is set to 1, the drives memory of the motors thermal state is retained even when power is removed. If the
drive is tripped on an Motor Overload detected fault OL2, a cooling time (as calculated by the drive) needs to expire before the
motor can be restarted.
(1) Catch-on-the-fly motor starting after a drive detected fault is active if auto clear is enabled
(parameter [Number auto reset] (F303) is not set to 0, see page 124)
0 [Cleared]
If parameter F602 is set to 0 and the drive is powered after a detected fault:
If the cause of the detected fault has been removed, the drive will reset and can be started. Information about the detected fault
just cleared will be transferred to the detected fault history.
If the cause of the detected fault has not been removed, the detected fault will be displayed again but the drives memory of the
operational information associated with the detected fault will be transferred to the detected fault history.
Information about the 4th most recent detected fault will be removed from the detected fault history.
1 [Retained]
If parameter F602 is set to 1 and the drive is powered after a detected fault:
If the cause of the detected fault has been removed, the drive will reset and can be started. Information about the detected fault
just cleared will be transferred to the detected fault history.
If the cause of the detected fault has not been removed, the original detected fault and all of its operational data will be available
for viewing as the current detected fault in the monitoring mode.
Information about the 4th most recent detected fault will be retained in the detected fault history.
Auto clear will be disabled.
0 [Disable]: Disabled
If parameter F608 is set to 0, input phase loss detection is disabled. Loss of one input phase will not cause the drive to trip.
[Enable]: Enabled
1 If parameter F608 is set to 1, the loss of one input phase will cause an EPH1 detected fault.
0 [Disabled]
If parameter F302 is set to 0 and the drive briefly loses input power, it may not trip but may instead experience a momentary
reduction of motor voltage and/or current and then resume normal operation once nominal input power is restored.
1 [Do not use]: DO NOT SELECT
2 [Freewheel]
If parameter F302 is set to 2 and the drive briefly loses input power, the drive will remove power from the motor and allow it to
coast to a stop. The embedded display terminal will flash StOP. The drive can only be restarted by providing a new run com-
mand.
Input Voltage
Motor Speed
CAUTION
RISK OF DAMAGE TO DRIVE
When F627 = 2 , use a line choke.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
0 [Enable]
If parameter F305 is set to 0, and the drive detects an impending DC bus overvoltage, it will automatically take one of the fol-
lowing actions:
Increase the deceleration time
Keep the motor at a steady speed
Increase the motor speed
Output
Frequency
1 [Disabled]
If parameter F305 is set to 1, the drive will take no action to avoid a DC bus overvoltage.
2 [Quick deceleration]: Enabled (quick deceleration mode)
If parameter F305 is set to 2, and the drive detects an impending DC bus overvoltage, it will increase the V/Hz ratio of the
power applied to the motor. Motor over-excitation is used to dissipate regenerative energy into the motor instead of the drive.
3 [Dyn. deceleration]: Enabled (dynamic quick deceleration mode)
If parameter F305 is set to 3, the drive will increase the V/Hz ratio of the power applied to the motor as soon as slow down
begins instead of waiting for the DC bus voltage to approach the detected fault level.
When motor speed is being reduced, a DC bus overvoltage can often be caused by regenerated energy being absorbed by the
drive from the load and motor.
Parameter F626 sets the DC bus voltage level at which the actions defined by parameter F305 take place. See
diagram above for more details.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
z If F605 = 0, loss of cable is not detected
z If F605 =1 or 2, loss of cable is only detected at the startup of the motor
z Check this action will not endanger personnel or equipment in any way
Failure to follow these instructions will result in death or serious injury.
If output phase loss detection is enabled and an output phase loss persists for more than 1 second, the drive will trip and display
the EPH0 code.
0 [Disabled]
If parameter F605 is set to 0, output phase loss detection is disabled.
1 [First start]: At the first start-up.
If parameter F605 is set to 1, an output phase loss check is made only during the first motor start-up after power is applied to
the drive.
2 [Each start]: At every start-up.
If parameter F605 is set to 2, an output phase loss check is made every time the motor is started.
3 [During run]: During operation.
If parameter F605 is set to 3, continuous output phase loss monitoring is performed while the motor is running.
4 [Permanent]: At start-up and during operation.
If parameter F605 is set to 4, monitoring for an output phase loss is performed at motor start-up and continuously during op-
eration.
5 [Output contactor]: Load side disconnect mode.
Setting 5 for parameter F605 is for applications with a load side disconnect. The drive will automatically restart the motor if the
following are true:
- An all-phase loss has been detected (an output contactor or a load side disconnect has opened)
- The drive detects that a 3-phase connection has been reestablished (the output contactor or load side disconnect has
closed). It is necessary to wait 1 s between disconnection and connection. See following scheme to have an example of
loss of output contactor.
Speed
t
Ouput contactor t1 t2
1
0 t
0 [Alarm]
If parameter F610 is set to 0, relay output functions 24 or 25 (see page 130) can be used to signal an underload condition
without the drive faulting.
1 [Fault]
If parameter F610 is set to 1 and the loading level drops below the setting of F611 for a period of time longer than that set
by F612, the drive will trip, displaying code UC. The fault relay will be set if one has been defined (relay output functions 10 or
11, see page 98). A relay assigned to signal an underloaded condition (functions 24 or 25, see page 99) will also be set.
The drives response to an underload condition is set by parameters F609, F610, F611, and F612.
The setting of parameter F610 determines whether an underload condition signals an alarm with an output relay or faults the
drive.
The sum of parameters F609 and F611 determines the drive loading level that will clear an underload alarm/detected fault.
Parameter F612 determines how long the drive can be under load before an alarm or detected fault is signaled.
See parameters F609, F610, F611 and F612 diagram below for more details.
F610 = 0 (Alarm Only)
ON
F612 or Less
Output Current (%)
Time [Sec]
0 [Disabled] Disabled.
If parameter F633 is set to 0, the drive will not monitor for loss of signal at analog input terminal VIA
1 to 100 [Fault detection level]
If parameter F633 is set to a value greater than 0 and:
The signal at VIA drops below the detection level selected,
and, the low signal level persists for 300 milliseconds or longer,
the drive will trip and the embedded display terminal will display the code E-18.
(1) Percentage of the drives current rating. Display can also be in amperes, depending on setting of parameter
[Unit value selection] (F701) (see page 120).
(2) Percentage of [Underload level] (F611) setting.
(3) Percentage of maximum VIA signal level
0 [No]: No
1 [Freewheel] Freewheel.
Freewheel stop and alarm.
2 [Set speed] Fallback speed.
Switch to fallback speed. Maintained as long as the trip cause is present and the run command is not disabled. See parameter
[4-20mA fallback sp] (F649) for fallback speed.
3 [Keep speed] Speed maintain.
The drive maintains the speed being applied when the trip occurred, as long as the trip cause is present and the run command is
not disabled.
4 [Ramp stop] Ramp stop.
F649 [4-20mA fallback sp] Fallback speed 0.0 to [Max frequency] (FH) 0.0 Hz
0 [Each time (std)]: Each time a RUN command is given (standard pulse)
1 [One time (std)]: Only one time after power is turned on (standard pulse)
2 [Each time (short)]: Each time a RUN command is given (short-time pulse)
3 [One time (short)]: Only one time after power is turned on (short-time pulse)
The setting of parameter F613 determines how the drive determines an output short-circuit during start-up.
Select the short-time pulse if the drive is powering a low impedance motor.
Overtorque Detection
The drives response to a particular motor torque level is determined by the setting of parameters F615
F619.
ON
Time (Sec)
0 [Alarm]
If parameter F633 is set to 0, the drive will not monitor for loss of signal at analog input terminal VIA.
1 [Fault]
If parameter F615 is set to 1 and the drive faults, the overtorque signal output will remain latched on until the detected fault is
cleared.
Depending on the setting of parameter F615, the drive can use output relay function 12 or 13 (see table on pages 98) to signal
an overtorque alarm or detected fault (Ot code).
The setting of parameter F616 determines the level at which the drive will act upon a motor overtorque condition (see diagrams
above and below).
x 0.7
x 0.7
Output Frequency
level 2
Torque Current (%)
Time (Sec)
Output relay functions 20 or 21 can be used to signal a overtorque pre-alarm when the calculated motor torque reaches 70% of
the value set by parameter F616.
The setting of parameter F618 determines how long the drive needs to detect a motor overtorque condition before it signals an
alarm or detected fault (see above diagram).
F619 [Overtorque band] Overtorque Detection Level Bandwidth 0 to 100 % of F616 10%
level
While the setting of parameter F616 determines the level at which a motor overtorque alarm or detected fault will be signaled,
the setting of parameter F619 determines how far the calculated motor torque needs to drop before the alarm or detected fault
is cleared (see above diagram).
F634 [Amb. temp. alarm] Ambient Temperature For drive Service Alarm 3
1 [- 10 to 10 C]
2 [11 to 20 C]
3 [21 to 30 C]
4 [31 to 40 C]
5 [41 to 50 C]
6 [51 to 60 C]
The drive can be programmed to signal a service alarm using output relay functions 44 or 45 (see page 102). The status of the
service alarm can be displayed on the embedded display terminal (see page 21).
At initial start-up, set parameter F634 to the drives average ambient operating temperature. Setting F634 to the highest
annual temperature or changing the value after drive operation has begun may result in an early drive service alarm.
Parameters F481 to F483 can be used to avoid nuisance overvoltage and input phase faults caused by:
z High input impedance: line reactor
z Low input impedance: high kVA distribution network
z Voltage instability: generator power source
If nuisance faults occur, increase the value of parameter F481. If increasing the value of F481 over 1000
does not remove nuisance faults, increase the values of parameters F482 and F483 as needed.
F481 [In noise comp. filter] Line noise compensation filter 0 to 9999 s 0 s
F482 [In noise Inhibit filter] Line noise Inhibitor filter 0 to 9999 s 442 s
F483 [In noise inhibit gain] Line noise Inhibitor gain 0 to 300 % 100%
F484 [Pwr supply adj. gain] Power supply adjustment gain 0.0 to 2.0 s 0.0
When the using machine has specific resonance, the following phenomena are happened:
z the machine occurs vibration,
z unusual noise of machine or peripheral.
Note: F481 and F483 are invalid when F484 has a value excluding 0.0.
Motor Type
Set OLM to 0, 1, 2, or 3 if a self-cooled motor is being powered by the drive. The diagram below illustrates
the overload protection level for the self-cooled motor as a function of motor frequency.
Overload Protection for a Self-Cooled Motor
x 01.0
x 0.55
Set OLM to 4, 5, 6, or 7 if a forced-cooled motor is being powered by the drive. The diagram below illustrates
the overload protection level for the forced-cooled motor as a function of motor frequency.
x 01.0
x 0.6
Overload Protection
To enable motor overload protection, set OLM to 0, 1, 4, or 5.
CAUTION
RISK OF DAMAGE TO THE MOTOR
When OLM is set to 2, 3, 6 or 7 motor thermal protection is no longuer provided by the drive. Provide an
alternative means of thermal protection.
Failure to follow these instructions can result in equipment damage.
To disable motor overload protection, set OLM to 2, 3, 6, or 7. In this case, a separate overload protective
device, external to the ATV212 drive, needs to be wired between the drive and the motor.
Overload Stall
The overload stall function is only compatible with variable torque loads where the load on the motor and drive
is dependent on the operating frequency and where the load can be reduced by slowing the motor.
If overload stall is enabled, the drive will reduce its output frequency if it detects an impending overload. As the
overload condition of the motor is dissipated, the drive will return its output frequency to the commanded value.
To enable overload stall, set OLM to 1, 3, 5, or 7.
To disable overload stall, set OLM to 0, 2, 4, or 6.
CAUTION
RISK OF DAMAGE TO THE MOTOR
When OLM is set to 2, 3, 6?or 7 motor thermal protection is no longuer provided by the drive. Provide an
alternative means of thermal protection.
Failure to follow these instructions can result in equipment damage.
Protection
Motor OLM
Description Behavior
type Overload Overload value
protection stall
(1) If the speed is lower than the fallback speed, the drive will keep the same speed.
11
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Network communication between the ATV212 drive and a master controller 138
WARNING
LOSS OF CONTROL
The designer of any control scheme must consider the potential failure modes of control paths and, for
certain critical control functions, provide a means to achieve a safe state during and after a path failure.
Examples of critical control functions are emergency stop and overtravel stop.
Separate or redundant control paths must be provided for critical control functions.
System control paths may include communication links. Consideration must be given to the implications of
unanticipated transmission delays or failures of the link (1).
Failure to follow these instructions can result in death, serious injury, or equipment damage.
(1) For additional information, refer to NEMA ICS 1.1 (latest edition), Safety Guidelines for the Application, Installation, and Maintenance of Solid
State Control and to NEMA ICS 7.1 (latest edition), Safety Standards for Construction and Guide for Selection, Installation and Operation
of Adjustable-Speed Drive Systems.
Network communication between the ATV212 drive and a master controller is possible through five protocols
selectable through the embedded display terminal:
z Modbus RTU
z Metasys N2
z Apogee P1 FLN
z BACnet
z LonWorks
Three types of data exchange are possible:
z Monitoring: monitoring values such as output frequency, voltage, and current
z Programming: reading, editing, and writing drive parameters
z Control: starting and stopping the drive and controlling the frequency reference
For operation on a network containing multiple drives, each ATV212 drive needs to be assigned a unique
address using parameter F802.
For operation on a network where all drives are slaves responding to a central control system:
z Parameters [Command mode sel] (CNOd) (see page 77) and [Frequency mode sel] (FMOd) (see page
77) needs to be set correctly:
- Setting CMOd to 2 enables start/stop control of the drive via network communication
- Setting FMOd to 4 enables the frequency reference to be controlled by network communication
- Setting either CMOd to 2 or FMOd to 4 enables serial communication error detection. The setting of
parameter F851 determines the drives response in case of a loss of communication.
Control of the ATV212 drive can be established by a master controller over a serial communication network
regardless of the setting of CMOd or FMOd (see diagram on page 46). Control can be restored to the source
defined by CMOd and FMOd if the serial communication network relinquishes control or a logic input
assigned to function 48 (forced local) is enabled.
0 [9600 bps]
1 [19200 bps]
0 [No]: No parity
1 [Even]: Even parity
2 [Odd]: Odd parity
WARNING
LOSS OF CONTROL
z If F803 is set to 0, communication control will be inhibited.
z For safety reasons, inhibiting the communication interruption detection should be restricted to the debug phase or to special
applications.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
0 [9600]
1 [19200]
0 [No]: No parity
1 [Even]: Even parity
2 [Odd]: Odd parity
1 [Mdb RTU]
2 [Metasys N2]
3 [Apogee P1]
4 [BACnet]
5 [LonWorks]
WARNING
LOSS OF CONTROL
If F851 is set to 1, communication control will be inhibited.
For safety reasons, inhibiting the communication interruption detection should be restricted to the debug
phase or to special application.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
WARNING
LOSS OF CONTROL
Know and understand the setting of parameter F851. This parameter controls the behavior of the drive in the event of a
network communication loss. If the value of F851 is 0, 1, 2, or 3, the drive will not trip on an Err8.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
0 Ramp stp (F/Cmod): Drive ramps to a stop. Serial control is relinquished to the sources defined by [Frequency mode sel] (FMOd)
and [Command mode sel] (CMOd). This function is only used with the Lonworks terminal board.
Note: For Modbus connection, only the function 1 is taken into account. The other function make drive trip in Err8 or Err5.
1 [2 poles]
2 [4 poles]
3 [6 poles]
4 [8 poles]
5 [10 poles]
6 [12 poles]
7 [14 poles]
8 [16 poles]
The free notes parameter can be used to set a unique value to identify the drive on a network.
Parameters F890 F896 should be adjusted only if the corresponding optional equipment has been
installed. See the ATV212 catalog for more detail.
When the value of F829 parameter is changed, the adjustment range and factory setting of F890 to
F896 are automatically setted.
Modbus APOGEE FLN P1 METASYS N2 BACNET
Setting Factory Setting Factory Setting Factory set- Setting Factory
Range setting Range setting Range ting Range setting
F829 - 1 3 3 2 2 4 4
F890 0 to 65535 0 1 to 99 99 1 to 255 1 0 to 127 0
F891 0 to 6 0 1 to 5 5 1 to 5 5
F892 20 to 600 100 20 to 600 100 20 to 600 100
F893 0 to 4194 0 0 to 4194 0 0 to 4194 0
F894 0 to 999 0 0 to 999 0 0 to 999 0
F895 0 to 127 0 0 to 127 0 0 to 127 127
F896 0 to 100 0 0 to 100 0 1 to 100 1
There are 2 connection port witch support different communication protocol, embedded or using option board.
The two channels could communicate simultaneously with the product, but only one could send the logical or
frequency command to the drive:
z The two channel used for monitoring
z One channel used for command (run order and speed) and the second for monitoring.
The configuration parameters of communication are taking account at next power up of the product.
Description RJ45 Network Network Network Network Network
Modbus Modbus Apogee P1 Metasys N2 BACnet LonWorks
F829 Network selection - p p p p p
F800 Modbus RJ45 Baud rate p - - - - -
F801 Modbus RJ45 Parity p - - - - -
F802 Modbus address p p - - - -
F803 Modbus time out p p - - - (1)
F851 Com fault behavior p p p p p p
F820 Modbus Net Baud rate - p - - - -
F821 Modbus Net Parity - p - - - -
F890 Network parameter - - p p p -
F891 Network parameter - - p - p -
F892 Network parameter - - p p p -
F893 Network parameter - - - - p -
F894 Network parameter - - - - p -
F895 Network parameter - - - - p -
F896 Network parameter - - - - p -
12
What's in this Chapter?
This chapter contains the following topics:
Topic Page
Overview 144
Overview
Use parameters [Freq. pedestal] (F241) and [Freq. pedestal hyst.] (F242) to enable start/stop control of the
drive based on the speed reference level.
If the drive operates normally and has a run permissive signal, it will start powering the motor as soon as the
speed reference level exceeds the frequency set by F241 + F242 (point B in diagram below). It will remove
power from the motor as soon as the output frequency drops below the level set by F241 F242 (point A
in diagram below).
0 A B 100%
Speed Reference
F241 [Freq. pedestal] Operating starting frequency] 0.0 to [Max frequency] (FH) Hz 0.0 Hz
F242 [Freq. pedestal hyst.] Operating starting frequency hysteresis 0.0 to [Max frequency] (FH) Hz 0.0 Hz
Droop Control
13
What's in this Chapter?
This chapter contains the following topics:
Topic Page
The use of droop control (or negative slip compensation) can help balance the load between multiple motors in
a load sharing application. The amount of slip or speed droop allowed in the motor powering the load is
determined by the load current level and the setting of parameters F320 and F323.
During motoring, droop control decreases the drive output frequency. During regenerative braking, droop control
increases the drive output frequency.
When enabled, droop control is active when:
z The load current exceeds the level set by parameter F323.
z The drive output frequency is between the [Mot start freq.] F240 (see page 82) and [Max frequency] (FH)
(see page 82).
Operation frequency: f1
0 T1 100%
Torque current (%)
The amount of speed droop allowed (f) can be calculated by this equation:
f = uL(1) x F320 x (load current F323)(2)
Example:
uL = 60 Hz
F320 = 10%
F323 = 30% (of drives rated current)
Load current = 100% of drives rating
f = 60 x 0.1 x (1 0.3)
f = 60 x 0.07
f = 4.2
Assuming the speed reference is set to 60 Hz, the output frequency will be: f1 = f0 f = 60 4.2 = 55.8 (Hz).
(1) Parameter [Motor Rated freq] (uL) (see page 70). The value entered for uL in this formula should not exceed 100,
regardless of the actual setting of parameter uL.
(2) Speed droop is zero if (load current F323 = 0).
(3) Percent of the drives rated current.
III
What's in this Part?
This part contains the following chapters:
14
What's in this Chapter?
This chapter contains the following topics:
Topic Page
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Read and understand the instructions in Before you begin chapter, before performing the procedure in
this section.
Failure to follow these instructions will result in death or serious injury.
Alarm Codes
Code Name Possible causes Remedies
CFI2 [Download transfer Invalid configuration. Check the configuration loaded previously.
fault] The configuration loaded in the drive via the Load a compatible configuration.
bus or communication network is
inconsistent.
Transfer using PC soft has not been To perform download, uncheck "Display
successful due to rating differences communication error" (in Tool /
(for example upload of an ATV212pppN4 Environnement option / Startup/Comm.)
configuration to an ATV212pppM3)
E-18 [VIA signal fault] The VIA analog signal is below the level set Check the signal at VIA and rectify the cause
by parameter F633. of the signal loss.
Verify that parameter F633 is set
correctly.
E-19 [CPU communica- Communication error between control CPUs Contact Schneider Electric to repair the
tions err.] drive.
E-20 [Excess torque boost Torque boost parameter Repeat the drive auto-tune and then adjust
flt] [Auto Torque Boost] (F402) is set too down parameter [Auto Torque Boost]
high. (F402).
The motor impedance is too low.
During deceleration when Set [Auto ramp] (AU1) = (0) [Disabled]
[Mot cont. mode sel.] (Pt) = (1) [Quadr. U/F] Decrease the deceleration ramp with
with 3 conditions: [Deceleration time 2] (F501) and
- Processing for stop [Commut. ramp freq.] (F505).
- Load current value > 88% x [Motor Current
Limitation] (F601)
- Too slow deceleration, [Max frequency]
(FH) /[Deceleration time 1] (dEC) x 2 msec
< 0.01Hz
E-21 [CPU error 2 fault] The control board CPU is inoperable. Contact Schneider Electric to repair the
drive.
E38 [EEprom pwr incom- Eeprom power incompatible. Contact Schneider Electric to repair the
pat.] Product hardware detected fault. drive.
EEP1 [EEPROM error 1 A data writing error has occurred. Cycle power to clear the detected fault.
fault]
EEP2 [EEPROM error 2 Power was removed from the drive during a Cycle power to clear the detected fault and
fault] parameter reset operation resulting in a try the parameter reset operation again.
data writing error. If the detected fault does not clear, contact
Schneider Electric to repair the drive.
EEP3 [EEPROM error 3 A data reading error has occurred. Cycle power to clear the detected fault.
fault]
EF2 [Ground fault] Ground fault in motor or motor cables Check the motor and motor cables for
ground faults.
EPHO [Output phase loss Loss of one or more output phases Determine the cause of the missing output
fault] phase (such as a bad connection, an output
disconnect, or an open winding in the motor)
and rectify the trouble.
Check parameter F605.
EPHI [Input phase loss Loss of one input phase Determine the cause of the missing input
fault] phase and rectify.
Check parameter F608.
Err1 [Speed ref. error Parameters F202, F203, F210, or Set the parameters to the correct settings.
fault] F212 are set improperly.
Alarm Conditions
Alarms do not cause the drive to enter a fault condition.
Alarm Codes
Code Description Possible causes Remedies
Atn1 [Auto tune] Auto-tuning in process Normal if it the message disappears
after a few seconds.
CLr [Reset active] This message is displayed after the Press the STOP key again to clear the
STOP key is pressed while an detected detected fault.
fault is displayed.
db [DC braking] DC braking in process The alarm code goes off in several
seconds if no trouble occurs.
dbOn [dbOn] Motor shaft fixing control
E-17 [HMI error] A graphic display option key has been Release the graphic display option
held down for more than 20 seconds. key.
A graphic display option key may not be If this does not clear the error, replace
operating properly. the drive.
EI [Excess value] The number The number of digits entered for values Lower the frequency free-unit
of digits that can be such as frequencies is more than 4 (the magnification [Customized freq val]
displayed has been upper digits have priority). (F702).
exceeded
EOFF [Loc. Stop en.] The operation panel is used to stop the Press the STOP key for an emergency
operation in automatic control or remote stop. To cancel the emergency stop,
control mode. press any other key.
Err1 [Speed ref alarm] The frequency setting signals at points 1 Set the frequency setting signals at
and 2 are set too close to each other. points 1 and 2 apart from each other.
h999 [Pin&1MWh] Integral input Integral input power is more than Press and hold down the ENT key for
power 999.99 kWh. 3 s or more when power is off or when
the input terminal function CKWH is
turned on or displayed.
H999 [Pout&1MWh] Integral Integral output power is more than Press and hold down the ENT key for
output power 999.99 kWh. 3 s or more when power is off or when
the input terminal function CKWH is
turned on or displayed.
HEAd [Head] The first and last data item in the auh Press MODE key to exit the data
End [End] data group is displayed. group.
Display of first/last data
items
H1 [High] During programming, a value was Enter a value within the bounds of the
LO [Low] entered that exceeds the maximum or parameter
Parameter adjustment minimum value of the parameter.
error
InIt [Initialization] Parameters are being initialized to Normal if the message disappears
default values. after several seconds.
LStp [Low speed stop] Auto-stop The automatic stop function selected To deactivate the automatic stop
because of continuous with F256 was activated. function, increase the frequency
operation at the lower-limit command above the lower-limit
frequency frequency LL+F391 or turn off the
operation command.
NOFF [Line undervolt flt] The phase-to-phase input voltage is too Measure the main circuit supply
low. voltage. If the voltage is at a normal
level, the drive requires repair.
OFF [Drive stop] The ST-CC (run permissive) circuit is Close the ST-CC circuit.
open.
nSt [Lock State] The Li is already active when the function Deactivate the active Li configured.
is validated.
The Li is already active when a
configuration transfer is done with the
function is validated.
rtrY [Auto reset] The drive is in the process of restart. The drive is operating normally if it
A momentary stop occurred. restarts after several seconds.
StOp [Stop supply] Momentary The slowdown stop prohibition function To restart operation, reset the drive or
power loss slowdown stop set with F302 (momentary power loss input an operation signal again.
prohibition function ride-through operation) is activated.
activated.
Pre-alarm Conditions
Pre-alarm Codes
Code Pre-alarm Description
C [Current alarm] The drive is at current limit.
For more information, refer to parameter F601 (see page 69) and F185 (see page 74).
P [DC bus alarm] The drive is approaching an overvoltage detected fault due to a high supply line, regenerative
motor braking, or a combination of these. For more information, refer to parameters F305
(see page 128) and F626 (see page 128).
L [Motor overload al] The motor overload timer has reached or exceeded 50% of its detected fault level.
H [Drv overheat alrm] The drive is approaching an overheating fault detection.
The pre-alarm codes are displayed, flashing on the embedded HMI, in the following order from left to right: C,
P, L, H.
If two or more troubles arise simultaneously, one of the following pre-alarm codes appears and flashes: CP, PL,
CPL.
When any overload function (OL1 or OL2) is active, the drive cannot be reset by inputting a reset signal from
an external device or with the Stop key on the display terminal if the calculated cooling time has not expired.
Calculated cooling time:
- OL1: 30 seconds after the detected fault has occurred
- OL2: 120 seconds after the detected fault has occurred
CAUTION
RISK OF DAMAGE TO THE MOTOR
z Repeated reset of the thermal state after a thermal overload can result in thermal stress to the motor.
z When trips occur, promptly inspect the motor and driven equipment for problems (such as a locked shaft or
mechanical overload) before restarting. Also check the power supplied to the motor for abnormal conditions
(such as a phase loss or phase imbalance).
Failure to follow these instructions can result in equipment damage.
Annex
IV
What's in this Part?
This part contains the following chapters:
15 Migration 159
Migration
15
What's in this Chapter?
This chapter contains the following topics:
Topic Page
General
The ATV212 is compatible with the ATV21
Migration Modbus ATV21 to ATV212: When controlling ATV21 using Modbus RJ45, parameter [Network
protocol] (F829) should be set to 1.
With ATV212, parameter F829 should also be set to 1 and parameter [Com channel choice] (F807) set
to [RJ45] (0). Factory setting is [Open style] (1).
Settings of other communication parameters described from page 138 remain the same as on ATV21.
Note: For LonWorks, parameter F829 needs to be set to 1 for ATV21 and needs to be set to 5 for ATV212.
At the end of download transfer, the drive cannot run if a logic input configured to a function is active. To use the
function and run the motor, it's necessary to disable and enable the logic input.
Commissioning
Compatible loader tool with ATV21
z PC Soft V1.0 and higher
16
Parameter Reset
Refer to Menu navigation diagram page 62 to know how to reach [Parameter reset] (tYP) parameter.
The Altivar 212 drive offers three parameter reset options:
z Factory reset: [Parameter reset] (tYP) = 3
z 50 Hz reset: [Parameter reset] (tYP) = 1
z 60 Hz reset: [Parameter reset] (tYP) = 2
Parameter values that vary According to drive rating, but not reset type
The table below lists the parameters whose values, after a reset, depend on the drive model.
To determine the value of a parameter after a reset, locate the drive model number in first column and read
across the row to the column that corresponds to the parameter code. The number that appears at the
intersection of the model number and the parameter code is the parameters value after a reset. These values
are the same for every reset types ([Parameter reset] (tYP) = 1, [Parameter reset] (tYP) = 2, or
[Parameter reset] (tYP) = 3).
Parameters whose values after a reset are drive model dependant but do not vary by reset type
Parameter
Reference ACC dEC vLv ub F171 F172 F300 F402 F494 F626 F749
s s V % V % kHz % - % -
ATV212H075M3X 10 10 200 6 200 6 12 5.8 80 140 0
ATV212HU15M3X 10 10 200 6 200 6 12 4.3 70 140 0
ATV212HU22M3X 10 10 200 5 200 5 12 4.1 70 140 0
ATV212HU30M3X 10 10 200 5 200 5 12 3.7 70 140 0
ATV212HU40M3X 10 10 200 5 200 5 12 3.4 70 140 1
ATV212HU55M3X 10 10 200 4 200 4 12 3.0 70 140 1
ATV212HU75M3X 10 10 200 3 200 3 12 2.5 70 140 1
ATV212HD11M3X 10 10 200 2 200 2 12 2.3 60 140 1
ATV212HD15M3X 10 10 200 2 200 2 12 2.0 50 140 1
ATV212HD18M3X 30 30 200 2 200 2 8 2.0 50 140 1
ATV212HD22M3X 30 30 200 2 200 2 8 1.8 50 140 1
ATV212HD30M3X 30 30 200 2 200 2 8 1.8 50 140 1
ATV212H075N4 10 10 400 6 400 6 12 5.8 80 140 0
ATV212HU15N4 10 10 400 6 400 6 12 4.3 70 140 0
ATV212HU22N4 10 10 400 5 400 5 12 4.1 70 140 0
ATV212HU30N4 10 10 400 5 400 5 12 3.7 70 140 0
ATV212HU40N4 10 10 400 5 400 5 12 3.4 70 140 1
ATV212HU55N4 10 10 400 4 400 4 12 2.6 70 140 1
ATV212HU75N4 10 10 400 3 400 3 12 2.3 70 140 1
ATV212HD11N4 10 10 400 2 400 2 12 2.2 60 140 1
ATV212HD15N4 10 10 400 2 400 2 12 1.9 50 140 1
ATV212HD18N4 30 30 400 2 400 2 8 1.9 50 140 1
ATV212HD22N4S 30 30 400 2 400 2 6 1.8 50 140 1
ATV212HD22N4 30 30 400 2 400 2 8 1.8 50 140 1
ATV212HD30N4 30 30 400 2 400 2 8 1.8 50 140 1
ATV212HD37N4 30 30 400 2 400 2 8 1.8 50 140 2
ATV212HD45N4 30 30 400 2 400 2 8 1.7 50 140 2
ATV212HD55N4 30 30 400 2 400 2 8 1.6 40 140 2
ATV212HD75N4 30 30 400 2 400 2 8 1.5 40 140 2
Parameter values that vary According to drive rating and reset type
The table below lists lists the parameters whose values, after a reset, depend on the drive model and the reset
type ([Parameter reset] (tYP) = 1, [Parameter reset] (tYP) = 2, or [Parameter reset] (tYP) = 3). To
determine the value of a parameter after a reset:
The number that appears at the intersection of the drive model number and the parameter code is the
parameters value after a reset of the specified type.
Parameters whose values after a reset are drive model and reset type dependant
Factory reset tYP = 3 50 Hz reset tYP = 1 60 Hz reset tYP = 2
Reference tHr F173 F185 F601 tHr F173 F185 F415 F416 F417 F601 tHr F173 F185 F415 F416 F417 F601
% % % % % % % A % rpm % % % % A % rpm %
ATV212H075M3X 100 100 110 110 100 100 110 3.5 64 1400 110 100 100 110 3.0 60 1700 110
ATV212HU15M3X 100 100 110 110 100 100 110 6.1 61 1420 110 100 100 110 5.8 59 1715 110
ATV212HU22M3X 100 100 110 110 100 100 110 8.8 59 1430 110 100 100 110 8.0 61 1715 110
ATV212HU30M3X 100 100 110 110 100 100 110 12.5 63 1420 110 100 100 110 12.4 48 1760 110
ATV212HU40M3X 100 100 110 110 100 100 110 15.8 61 1425 110 100 100 110 15.2 51 1769 110
ATV212HU55M3X 100 100 110 110 100 100 110 20.6 57 1430 110 100 100 110 22.0 53 1780 110
ATV212HU75M3X 100 100 110 110 100 100 110 26.3 54 1450 110 100 100 110 28.0 42 1780 110
ATV212HD11M3X 100 100 110 110 100 100 110 36.9 53 1450 110 100 100 110 36.0 39 1766 110
ATV212HD15M3X 100 100 110 110 100 100 110 49.5 53 1455 110 100 100 110 48.0 36 1771 110
ATV212HD18M3X 100 100 110 110 100 100 110 61.0 53 1455 110 100 100 110 61.0 39 1771 110
ATV212HD22M3X 100 100 110 110 100 100 110 68.0 53 1460 110 100 100 110 68.0 36 1771 110
ATV212HD30M3X 100 100 110 110 100 100 110 93.0 50 1460 110 100 100 110 93.0 33 1771 110
ATV212H075N4 100 100 110 110 100 100 110 2.0 64 1400 110 100 100 110 1.5 60 1720 110
ATV212HU15N4 100 100 110 110 100 100 110 3.5 61 1420 110 100 100 110 2.9 59 1700 110
ATV212HU22N4 100 100 110 110 100 100 110 5.1 59 1430 110 100 100 110 4.0 61 1715 110
ATV212HU30N4 100 100 110 110 100 100 110 7.2 63 1420 110 100 100 110 6.2 48 1715 110
ATV212HU40N4 100 100 110 110 100 100 110 9.1 61 1425 110 100 100 110 7.6 51 1760 110
ATV212HU55N4 100 100 110 110 100 100 110 11.9 57 1430 110 100 100 110 11.0 53 1769 110
ATV212HU75N4 100 100 110 110 100 100 110 15.2 54 1450 110 100 100 110 14.0 42 1780 110
ATV212HD11N4 100 100 110 110 100 100 110 21.3 53 1450 110 100 100 110 21.0 39 1780 110
ATV212HD15N4 100 100 110 110 100 100 110 28.6 53 1455 110 100 100 110 27.0 36 1766 110
ATV212HD18N4 100 100 110 110 100 100 110 35.1 53 1455 110 100 100 110 35.1 39 1771 110
ATV212HD22N4S 100 100 110 110 100 100 110 41.7 53 1460 110 100 100 110 41.7 36 1780 110
ATV212HD22N4 100 100 110 110 100 100 110 41.7 53 1460 110 100 100 110 41.7 36 1771 110
ATV212HD30N4 100 100 110 110 100 100 110 55.0 50 1460 110 100 100 110 55.0 33 1771 110
ATV212HD37N4 100 100 110 110 100 100 110 67 51 1475 110 100 100 110 67 31 1771 110
ATV212HD45N4 100 100 110 110 100 100 110 81 51 1475 110 100 100 110 71 34 1771 110
ATV212HD55N4 100 100 110 110 100 100 110 99 53 1480 110 100 100 110 86 31 1771 110
ATV212HD75N4 100 100 110 110 100 100 110 135 53 1480 110 100 100 110 114 31 1771 110
17
Use the Configuration Setting Table to look up parameter default settings, to record customized parameter
settings, and to look up sections of the manual, by page number, that contain detailed parameter descriptions.
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
FC 77 [Local speed ref.] Hz [Low limit frequency] (LL) to [Upper limit freq] (UL) 0.0
0 [Disabled]
AU1 85 [Auto ramp] - 1 [Enable] 1
2 [ACC only]
0 [Factory set]
1 [Run permissive]
AU4 63 [Auto set function] - 2 [3-wire] 0
3 [+/- Speed]
4 [4-20mA speed ref]
0 [Logic inputs]
CMOd 77 [Command mode sel] - 1 [HMI] 0
2 [Communication]
1 [Ref source VIA]
2 [Ref source VIB]
FMOd 77 [Frequency mode sel] - 3 [HMI reference] 1
4 [Serial com ref.]
5 [+/- Speed]
0 [Motor frequency]
1 [Motor current]
2 [Speed ref]
3 [DC bus U]
4 [Motor U]
5 [Input power]
6 [Output power]
7 [motor torque]
8 [Torque I]
9 [Motor thermal]
FMSL 108 [AO funct. selection] - 0
10 [Drive thermal]
11 [Do not use]
12 [Internal reference]
13 [VIA]
14 [VIB]
15 [Fixed 100%]
16 [Fixed 50%]
17 [Fixed 100%]
18 [Com data]
19 [Do not use]
FM 108 [AO scaling] -
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
0 [No action]
1 [50 Hz reset]
2 [60 Hz reset]
3 [Factory set]
4 [Trip cleared]
tYP 62 [Parameter reset] - 0
5 [Cumul time clear]
6 [EtYP fault reset]
7 [Save parameters]
8 [Recall parameters]
9 [Elapse time reset]
0 [Run FW]
1 [Run rev.]
Fr 77 [Local mot. direction] - 0
2 [Run FW+rev]
3 [Run rev+FW]
Model
ACC 83 [Acceleration time 1] s 0.0 3200 depen-
dent
Model
dEC 83 [Deceleration time 1] s 0.0 3200 depen-
dent
FH 82 [Max frequency] Hz 30.0 200.0 80.0
UL 82 [Upper limit freq] Hz 0.5 [Max frequency] (FH) 50.0
LL 82 [Low limit frequency] Hz 0.0 [Upper limit freq] (UL) 0.0
uL 70 [Motor rated freq.] Hz 25.0 200.00 50.0
230 V
50 330 230
models
uLu 70 [Motor Rated Voltage] V
460 V
50 660 400
models
0 [Constant V/Hz]
1 [Variable Torque]
2 [Cst V/Hz+Boost]
Pt 67 [Mot cont. mode sel.] - 3 [SVC] 1
4 [Economy]
5 [Do not use]
6 [Do not use]
Model
ub 68 [Motor Voltage Boost] % 0.0 30.0 depen-
dent
tHr 70 [Motor thermal prot.] %/A 10 100% of drives output current rating 100%
0 [Std mot. protect.]
1 [Std & stall mot. prot]
2 [Self cool]
3 [Slf cool stall ov.load]
OLM 135 [Motor overload prot] - 0
4 [Forced cool prot]
5 [Forc cool stall prot]
6 [Forced cool]
7 [F cool & stall ov load]
Sr1 112 [Preset speed 1] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 15
Sr2 112 [Preset speed 2] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 20
Sr3 112 [Preset speed 3] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 25
Sr4 112 [Preset speed 4] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 30
Sr5 112 [Preset speed 5] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 35
Sr6 112 [Preset speed 6] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 40
Sr7 112 [Preset speed 7] Hz 1 [Low limit frequency] (LL) to [Upper limit freq] (UL) 45
F100 114 [Freq. 1 reached] Hz - 0.0 to [Max frequency] (FH) 0.0
F101 114 [Freq. 2 reached] Hz - 0.0 to [Max frequency] (FH) 0.0
F102 114 [Freq.2 bandw.] Hz - 0.0 to [Max frequency] (FH) 2.5
F108 112 [Logic Funct 1 active] - 0 73 See table on page 91 0
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
0 AI
F109 90 [VIA selection] - 1 LI sink 0
2 LI source
F110 112 [Logic Funct 2 active] - 0 73 See table page 162 1
F111 90 [LI F selection] - 0 72 See table page 162 2
F112 90 [LI R selection] - 0 72 See table page 162 6
F113 90 [LI RES selection] - 0 72 See table page 162 10
F118 90 [VIA LI selection] - 0 73 See table page 162 7
0 61,
F130 109 [RY Relay Function 1] - See table page 162 4
254, 255
0 61,
F132 109 [FL Relay Function] - See table page 162 11
254, 255
0 61,
F137 113 [RY Relay Function 2] - See table page 162 255
254, 255
0 Function 1and 2
F139 113 [RY logic select.] - 0
1 Function 1 or 2
F146 109 [RY delay] s - 0.0 60.0 s 0.0
F147 110 [FL Relay delay] s - 0.0 60.0 s 0.0
F160 106 [VIA rel thresh. logic] % - 0 100 0
F161 106 [VIA threshold hyst.] % - 0 20 3
F162 106 [VIB rel thresh. logic] % - 0 100 0
F163 106 [VIB threshold hyst.] % - 0 20 3
F167 115 [Freq band det range] Hz - 0.0 to [Max frequency] (FH) 2.5
F170 74 [Mot 2 rated Freq.] Hz - 25.0 to 200.0 50.0
230V
50 to 330 230
model
F171 74 [Motor 2 rated Volt] V
460V
50 to 660 400
model
Model
F172 74 [Motor 2 Volt Boost] % - 0 30 depen-
dant
F173 74 [Motor 2 Overload] %/A - 10 100% of drive rating 100
F185 74 [Mot. 2 current limit] %/A - 10 110% 110
0 [Enable] 0
F200 108 [Auto/man speed ref] -
1 [Disable]
F201 106 [VIA ref point 1] % - 0 100 0
F202 106 [VIA freq. point 1] Hz - 0.0 200.0 0.0
F203 106 [VIA freq. point 2] % 0 100 100
F204 106 [VIA freq. point 2] Hz 0.0 200.0 50.0
1 [VIA]
2 [VIB]
F207 78 [Remote spd ref 2] - 3 [HMI] 2
4 [Communication]
5 [+/ Speed]
F210 106 [VIB ref. point 1] % 0 100 0
F211 106 [VIB freq. point 1] Hz 0.0 200.0 0.0
F212 106 [VIB ref. point 2] % 0 100 100
F213 106 [VIB freq. point 2] Hz 0.0 200.0 50.0
F240 82 [Mot start freq.] Hz - 0.5 10.0 0.5
F241 144 [Freq. pedestal] Hz - 0.0 [Max frequency] (FH) 0.0
F242 144 [Freq. pedestal hyst.] Hz - 0.0 [Max frequency] (FH) 0.0
F250 88 [DC brake start freq.] Hz - 0.0 [Max frequency] (FH) 0.0
F251 88 [DC braking current] %/A - 0 100% 50
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
F252 88 [DC braking time] s - 0.0 20.0 1.0
0 [Disable]
F256 78 [Time limit low spd] s 0.0
1 [Enable]
F264 113 [+speed LI resp time] s - 0.0 10.0 0.1
F265 113 [+speed freq. step] Hz - 0.0 [Max frequency] (FH) 0.1
F266 113 [- speed LI resp time] s - 0.0 10.0 0.1
F267 113 [- speed freq. step] Hz - 0.0 [Max frequency] (FH) 0.1
F268 113 [Init +/- Speed] Hz - 0.0 [Max frequency] (FH) 0.0
0 [Disable]
F269 113 [Init +/- Speed memo] - 1
1 [Enable]
F270 87 [Jump frequency 1] Hz - 0.0 [Max frequency] (FH) 0.0
F271 87 [Jump bandwidth 1] Hz - 0.0 30.0 0.0
F272 87 [Jump frequency 2] Hz - 0.0 [Max frequency] (FH) 0.0
F273 87 [Jump bandwidth 2] Hz - 0.0 30.0 0.0
F274 87 [Jump frequency 3] Hz - 0.0 [Max frequency] (FH) 0.0
F275 87 [Jump bandwidth 3] Hz - 0.0 30.0 0.0
F294 79 [Forced speed freq.] Hz - [Low limit frequency] (LL) [Upper limit freq] (UL) 50.0
0 [No bumpless] 1
F295 78 [Switch rem/Local] -
1 [Bumpless]
Model
F300 85 [Switch. freq. level] kHz - 6.0 16.0 depen-
dent
0 [Disable]
1 [Brief power loss]
F301 126 [Catch on fly] - 2 [Run restored] 3
3 [Power loss, run]
4 [Each start]
0 [Disabled]
F302 127 [Supply loss behav.] - 1 [Do not use] 0
2 [Freewheel]
0 [Disabled]
F303 124 [Number auto reset] - 3
1-10 [Number of fault reset attempts]
0 [Enable]
1 [Disabled]
F305 128 [Overvoltage fault] - 2
2 [Quick deceleration]
3 [Dyn. deceleration]
0 [Motor volt limit]
1 [Line & mot correct.]
F307 73 [Mot volt limitation] - 3
2 [No action]
3 [U Line correction]
0 [Fw & Rev.]
F311 86 [Motor direction] - 1 [Fw only] 1
2 [Rev. only]
0 [Disable]
F312 86 [Noise reduction] - 0
1 [Enable]
0 [Fixed]
1 [Auto]
F316 86 [Switch. freq. mode] - 1
2 [460 V fixed]
3 [460 V Auto]
F320 146 [Load gain] % - 0 100% 0
F323 146 [Load gain offset] % - 0 100% 10
F359 111 [PID ctrl wait time] s - 0 2400 0
0 [No PID]
F360 110 [PID control enable] - 1 [PID by VIA] 0
2 [PID by VIB]
F362 110 [PID Prop Gain] - - 0.01 100.0 0.30
F363 110 [PID Integral Gain] - - 0.01 100.0 0.20
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
F366 111 [PID Derivative Gain] - - 0.00 2.55 0.00
0 [No]
F380 111 [PID reverse error] - 0
1 [Yes]
F391 111 [Stop on LL hyst] Hz - 0.0 [Max frequency] (FH) 0.2
F392 111 [PID wake up (thres)] Hz - 0.0 [Max frequency] (FH) 0.0
F393 111 [PID wake up, feedb] Hz - 0.0 [Max frequency] (FH) 0.0
0 [Disabled]
F400 71 [Auto-tuning drive] - 1 [Initialize constant] 0
2 [Complete tune]
F401 74 [Slip Compensation] % - 0 150 50
Model
F402 74 [Auto Torque Boost] % - 0.0 30.0 depen-
dent
Model
F415 70 [Motor rated current] A - 0.1 200.0 depen-
dent
Model
F416 70 [Mot no-load current] % - 10.0 100.0 depen-
dent
Model
F417 70 [Motor rated speed] rpm - 100 15000 depen-
dent
F418 75 [Frequency loop gain] - - 1 150 40
F419 75 [Freq. loop stability] - - 1 100 20
F470 107 [VIA bias] - - 0 255 128
F471 107 [VIA gain] - - 0 255 148
F472 107 [VIB bias] - - 0 255 128
F473 107 [VIB gain] - - 0 255 148
F480 72 [No load cur. coef] - - 100 130 100
F481 133 [In noise comp. filter] s - 0 9999 0
F482 133 [In noise Inhibit filter] s - 0 9999 442
F483 133 [In noise inhibit gain] - - 0.0 300.0 100.0
F484 133 [Pwr supply adj. gain] - - 0.0 to 2.0 0.0
F485 72 [Stall control coef. 1] - - 10 250 100
F492 72 [Stall control coef. 2] - - 50 150 100
Model
F494 72 [Mot. adj coefficient] - - DO NOT ADJUST depen-
dant
F495 72 [Motor voltage coef.] % - 90 120 104
F496 72 [PWM adj. coef.] kHz - 0.1 14.0 14.0
F500 83 [Acceleration time 2] s 1 0.0 3200 20.0
F501 83 [Deceleration time 2] s 1 0.0 3200 20.0
0 [Linear]
F502 84 [Acc/dec 1 pattern] - 1 [S-ramp 1] 0
2 [S-ramp 2]
0 [Linear]
F503 84 [Acc/dec 2 pattern] - 1 [S-pattern 1] 0
2 [S-pattern 2]
1 [Ramp 1]
F504 85 [Ramp switching] - 1
2 [Ramp 2]
F505 85 [Commut. ramp freq.] Hz - 0.0 [Upper limit freq] (UL) 0.0
F506 84 [Acc/Dec S-pat start] % - 0 50 10
F507 84 [Acc/Dec S-pat end] - - 0 50 10
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
0 [No feedback]
1 [LIH set]
F580 117 [Damper fdb type] - 2 [LIL set] 0
3 [Com. LIH set]
4 [Com. LIL set]
F581 117 [Time open Damper] - - 0.05 to 300.00 s 60.00
F582 117 [Time close Damper] - - 0.05 to 300.00 s 60.00
0 [No fault]
F583 117 [Damper flt behavior] - 1 [Freewheel stop] 1
2 [Ramp stop]
F601 69 [Motor Current Limit] %/A - 10 110% 110%
0 [Cleared]
F602 127 [Drive fault memory] - 0
1 [Retained]
0 [Freewheel]
F603 115 [Ext. fault stop Mode] - 1 [Ramp stop] 0
2 [DC braking]
F604 115 [DC brk time ext flt] s - 0.0 20.0 1.0
0 [Disabled]
1 [First start]
2 [Each start]
F605 129 [Output phase loss] - 3
3 [During run]
4 [Permanent]
5 [Catch on fly]
F607 70 [Mot overload time] s - 10 2400 300
0 [Disable]
F608 127 [Input phase loss] - 1
1 [Enable]
F609 130 [Underload band] % - 1 20 10
0 [Alarm]
F610 130 [Underload det.] - 0
1 [Fault]
F611 130 [Underload level] %/A - 0 100% 0
F612 130 [Underload det. time] s - 0 255 0
0 [Each time (std)]
1 [One time (std)]
F613 131 [Short circuit det.] - 0
2 [Each time (short)]
3 [One time (short)]
0 [Alarm]
F615 132 [Overtorque det.] - 0
1 [Fault]
F616 132 [Overtorque level] % - 0 250 130
F618 132 [OvTorque det time] s - 0.0 10.0 0.5
F619 132 [Overtorque band] % - 0 100% 10
F621 120 [Run time alarm] h - 0.0 999.9 (0.1 = 1 hour, 100 = 1000 hours) 610.0
F626 128 [Overvoltage level] % 1 [100 150% of nominal DC bus voltage] 140
0 [Alarm (0.6U)]
F627 127 [Undervolt detect.] - 1 [Fault (0.6U)] 0
2 [Alarm (0.5U)]
0 [Disabled]
F632 126 [Mot overload memo] - 0
1 [Enabled]
0 [Disabled]
F633 130 [Loss of VIA] % 1??? 0
100
[Fault detection level]
1 [-10 to 10C]
2 [11 to 20C]
3 [21 to 30C]
F634 133 [Amb. temp. alarm] - 3
4 [31 to 40C]
5 [41 to 50C]
6 [51 to 60C]
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
0 [No]
1 [Freewheel]
F644 131 [4-20 mA loss] - 2 [Set speed] 0
3 [Keep speed]
4 [Ramp stop]
0 [Disabled]
F645 111 [Mot PTC selection] - 1 [Enabled fault] 0
2 [Enabled alarm]
F646 112 [PTC resistor value] W - 100 9999 3000
F649 131 [4-20mA fallback sp] Hz - 0 [Max frequency] (FH) Hz 0
0 [Disable]
F650 79 [Forced fire control] - 1 [Enable forward] 0
2 [Enable Reverse]
0 [Enable transition 0->1]
F659 79 [Forced fire function] - 1 [Enable level 1] 0
2 [Enable level 0]
0 [Negative slope]
F691 109 [AO slope] - 1
1 [Positive slope]
F692 109 [Analog output bias] % - 0 100% 0
F694 109 [Freq. for AO = 0V] Hz - 0 [Max frequency] (FH) Hz 0
F695 109 [Freq. for AO = 10V] Hz - 0 [Max frequency] (FH) Hz 0
0 [Unlocked]
F700 64 [Parameter lock] - 0
1 [Locked]
0 [%]
F701 120 [Unit value selection] - 1
1 [Amp or Volt]
0 Frequency displayed in Hz
F702 121 [Customized freq val] - 0.01 0
Conversion factor
200.0
0 [All]
F703 121 [Frequency convert.] - 0
1 [PID only]
0 [Negative slope]
F705 121 [Custom freq. slope] - 1
1 [Positive slope]
F706 121 [Customize unit bias] Hz - 0.00 [Max frequency] (FH) 0.00
0 [Disable]
F707 77 [Loc. speed ref. step] Hz 0.00
1 [Enable]
0 Disabled 0.1 Hz steps
F708 120 [Display ref. resol.] - 0
1 255 See formula on page 120
0 [Motor frequency]
1 [Reference]
2 [I Mot]
3 [Drive rated I]
4 [Drive therm state]
F710 120 [Displayed param.] - 5 [Motor power] 0
6 [Int speed ref]
7 [Com data]
8 [Motor speed]
9 [Com count]
10 [Com count norm st.]
0 [Ramp stop]
F721 78 [Loc. mot stop mode] - 0
1 [Freewheel]
0 [Enable]
F730 80 [Up/down key ref] - 0
1 [Disable]
0 [Permitted memo]
F732 80 [Loc/rem key] - 1 [Prohibited] 0
2 [Permitted no memo]
0 [Enable]
F733 80 [Run/stop key] - 0
1 [Disable]
0 [Enable]
F734 80 [Priority stop] - 0
1 [Disable]
0 [Disable]
F735 80 [HMI reset button] - 1
1 [Enable]
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
0 [AUF displayed]
F738 64 [Quick menu AUF] - 0
1 [AUF hidden]
0 [Disable] Model
F748 120 [Power cons. memo] - depen-
1 [Enable] dant
0 [1 kWh]
Model
1 [0.1 kWh]
F749 121 [Power cons. unit] kWh depen-
2 [0.01 kWh]
dant
3 [0.001 kWh]
0 [9600 bps]
F800 138 [Mdb RJ45 baud] - 1
1 [19200 bps]
0 [No]
F801 138 [Mdb RJ45 parity] - 1 [Even] 1
2 [Odd]
F802 138 [Modbus address] - - 0 247 1
0 Communication error detection disabled
F803 139 [Com. time out] s 3
1-100 1 to 100 seconds
0 [RJ45]
F807 139 [Com channel choice] - 1
1 [Open style]
0 [9600]
F820 139 [Mdb network baud] - 1
1 [19200]
0 [No]
F821 139 [Mdb network parity] s 1 [Even] 1
2 [Odd]
1 [Mdb RTU]
2 [Metasys N2]
F829 139 [Network protocol] - 3 [Apogee P1]
4 [BACnet]
5 [LonWorks]
0 [Ramp stp (F/Cmod)]
1 [No active]
F851 139 [Com. fault setting] - 2 [Ramp stop] 4
3 [Freewheel]
4 [Err5 or Err8]
1 [2 poles]
2 [4 poles]
3 [6 poles]
4 [8 poles]
F856 140 [Mot. poles (comm.)] - 2
5 [10 poles]
6 [12 poles]
7 [14 poles]
8 [16 poles]
0 [No select]
1 [Command word 1]
2 [Command word 2]
F870 140 [Block write data 1] - 3 [Frequency Setpoint] 0
4 [Relay command]
5 [FM command]
6 [Speed Setpoint]
0 [No select]
1 [Command word 1]
2 [Command word 2]
F871 140 [Block write data 2] - 3 [Frequency Setpoint] 0
4 [Relay command]
5 [FM command]
6 [Speed Setpoint]
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
0 [No select]
1 [Command 1]
2 [Freq. out]
3 [Motor current]
4 [Output volt]
5 [Alarm info]
F875 140 [Block read data 1] - 0
6 [PID feedback value]
7 [Input term. mon]
8 [Out term. mon]
9 [VIA monitor]
10 [VIB monitor]
11 [Mot speed mon.]
0 [No select]
1 [Command 1]
2 [Freq. out]
3 [Motor current]
4 [Output volt]
5 [Alarm info]
F876 140 [Block read data 2] - 0
6 [PID feedback value]
7 [Input term. mon]
8 [Out term. mon]
9 [VIA monitor]
10 [VIB monitor]
11 [Mot speed mon.]
0 [No select]
1 [Status info]
2 [Freq. out]
3 [Motor current]
4 [Output volt]
5 [Alarm info]
F877 141 [Block read data 3] - 0
6 [PID feedback value]
7 [Input term. mon]
8 [Out term. mon]
9 [VIA monitor]
10 [VIB monitor]
11 [Mot speed mon.]
0 [No select]
1 [Status info]
2 [Freq. out]
3 [Motor current]
4 [Output volt]
5 [Alarm info]
F878 141 [Block read data 4] - 0
6 [PID feedback value]
7 [Input term. mon]
8 [Out term. mon]
9 [VIA monitor]
10 [VIB monitor]
11 [Mot speed mon.]
0 [No select]
1 [Status info]
2 [Freq. out]
3 [Motor current]
4 [Output volt]
5 [Alarm info]
F879 141 [Block read data 5] - 0
6 [PID feedback value]
7 [Input term. mon]
8 [Out term. mon]
9 [VIA monitor]
10 [VIB monitor]
11 Mot speed mon.
F880 141 [Free ID parameter] - - 0 65535 0
F890 142 [Network adress] - - 0 65535 (1)
F891 142 [Network baud rate] - - 0 65535 (1)
Factory User
Code Page Name Unit Adjustment Range / Function
Setting Setting
F892 142 [Network time out] - - 20 - 600 (1)
F893 142 [Instance number H] - - 0 4194 (1)
F894 142 [Instance number L] - - 0 999 (1)
F895 142 [Max master] - - 0 127 (1)
F896 142 [Max info frames] - - 0 100 (1)
09/2011