Professional Documents
Culture Documents
Mil PRF 27260
Mil PRF 27260
MIL-PRF-27260C
27 November 1998
SUPERSEDING
MIL-T-27260B
28 December 1970
PERFORMANCE SPECIFICATION
This specification is approved for use by all Departments and Agencies of the Department of Defense.
1. SCOPE
1.1 Scope. This specification covers one type of 5,000-pound capacity aircraft cargo tie down. The tie down
is designated CGU-1/B and is furnished in a minimum length of 240 inches.
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This
section does not include documents cited in other sections of this specification or recommended for additional
information or as examples. While every effort has been made to ensure the completeness of this list, document
users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this
specification, whether or not they are listed.
2.2.1 Specifications, and standards. The following specifications and standards form a part of this document to
the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of
the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the
solicitation (see 6.2).
STANDARDS
DEPARTMENT OF DEFENSE
(Unless otherwise indicated, copies of the above standard are available from the Standardization Document Order Desk,
700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be
of use in improving this document should be addressed to: Technology & Industrial Services
Division, SA-ALC/TILDD, 485 Quentin Roosevelt Rd., Kelly AFB, Texas 78241-6425, by
using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the
end of this document or by letter.
2.3 Non-Government publication. The following document forms a part of this document to the extent specified
herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the
issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the
DODISS are the issues of the documents cited in the solicitation (see 6.2).
(Application for copies should be addressed to American Society for Quality Control, 611 East Wisconsin Avenue,
P.O. Box 3005, Milwaukee, WI 53201-3005, or to the American National Standards Institute, 11 West 42nd Street,
New York, NY 10036.)
(Application for copies should be addressed to RTCA, Inc., 1140 Connecticut Ave. NW, Washington, DC 20036.)
2.4 Order of Precedence. In the event of a conflict between the text of this document and the references cited
herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws
and regulations unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Qualification. The tie downs furnished under this specification shall be products that are authorized by
the qualifying activity for listing on the applicable qualified products list before contract award (see 4.2 and 6.3).
3.3 Materials. All materials shall be treated to resist corrosion due to electrolytic decomposition, fungus, salt
spray, and any other atmospheric conditions that may be encountered during operational use or storage (see 4.6).
3.4 Design. The tie down assembly shall be designed as an integral unit and shall not require attachment or
assembly of separate parts for operation. The tie down assembly shall be operable without the use of tools. The tie
down shall be designed so that no parts will work loose in service. Portions of the tie down which bear on the strap
when the tie down is in the operating position shall not incorporate knurled, serrated, or other types of surfaces that
could degrade the strap strength. The tie down shall be designed to be easily operable while wearing standard
aircrew work gloves (see 4.6).
3.5 Components. The tie down major components shall consist of a strap, a fixed hook assembly, and an
adjustable hook assembly that has an integrated adjusting, tensioning and release mechanism (see 4.6).
3.5.1 Strap. The strap shall incorporate a stop to prevent it from threading loose through the adjustable hook
assembly (see figure 1). The strap shall not have frayed ends. The strap shall not interfere with the operation and
locking of the tensioning lever (see 4.6).
3.5.2 Fixed hook assembly. The fixed hook assembly shall have a non-swiveling hook with a mechanism on the
hook to prevent inadvertent disengagement (see 4.6 and 4.7.1.3).
2
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
3.5.3 Adjustable hook assembly. The adjustable hook assembly shall have a non-swiveling hook, without an
inadvertent disengagement mechanism (see 4.6).
3.6 Interface.
3.6.1 Tie down dimensions. The overall dimensions of the tie down are shown in figure 1.
3.6.2 Hook dimensions. The hooks shall permit securing of the tie down to a ring having a minimum clear
opening of 0.75 inch diameter and a maximum cross section diameter of 0.875 inch (see 4.6).
3.6.3 Weight. The overall weight of the tie down assembly shall not exceed 3.75 pounds (see 4.6).
3.6.4 Strap color. The color of the strap shall be white (see 4.6).
3.7 Operation. The fixed hook assembly and the adjustable hook assembly shall attach to the aircraft tie down
rings (see 3.6.2) without the use of tools or other supplementary devices. The adjusting, tensioning, and release
mechanism requirements (see 3.8.3, 3.8.4, and 3.8.6) shall be accomplishable by personnel wearing standard
aircrew work gloves. The work gloves shall not cause interference (see 4.7.1.1).
3.8 Performance.
3.8.1 Proof load. The tie down shall be capable of withstanding a proof load of 5,000 pounds for 30 seconds
without slippage of the strap through the adjustment device. Damages such as broken sewing, broken or frayed
strap, and deformation or rupture of hardware shall not be permitted. The tie down shall be fully operational (see
4.7.4).
3.8.2 Ultimate load. The tie down shall be subjected to an ultimate load of 6,000 pounds for 30 seconds.
Damage such as broken sewing without complete separation, broken or frayed strap without complete separation of
the strap, and deformation but not rupture of hardware shall be permitted. The release mechanism shall be
operable (see 4.7.4.1).
3.8.3 Adjusting mechanism. The adjusting mechanism shall be capable of adjusting the tie down to any length
within the limits shown in figure 1. Adjustments in fixed increments of length shall not be acceptable. It shall be
possible to accomplish preliminary adjustments of the webbing to the approximate length required in a maximum
of 15 seconds. There shall be no inadvertent disengagement of the fixed hook assembly during tie down operations
(see 4.7.1.2).
3.8.4 Tensioning mechanism. The tensioning mechanism shall be of the progressive-take-up-ratchet type or
similar mechanism and shall be capable of taking up a minimum of one foot of strap. The tensioning mechanism
shall be capable of applying a tension of not less than 150 pounds using an applied force not to exceed 50 pounds.
No more than 7 progressive take-ups shall be required to obtain 150 pounds of tension with 18 feet of strap
between the hooks. The mechanical advantage of the mechanism shall not exceed 5. In the tightened position, the
operating lever shall not protrude. A lock shall be incorporated in the tensioning mechanism and shall
automatically engage upon completion of the tensioning operation. The force required to disengage the lock shall
not exceed 5 pounds (see 4.7.1.2).
3.8.5 Tensioning mechanism strength. The tensioning mechanism shall be capable of withstanding a minimum
applied force of 300 pounds without permanent deformation or malfunctioning of the mechanism. The tensioning
mechanism shall be operable (see 4.7.1.3).
3.8.6 Release mechanism. The release mechanism shall, when actuated, release the tensioning mechanism and
shall produce sufficient slack in the strap to permit removal of the attachment hooks. It shall be possible to
manually release a tension load of 750 pounds, with the applied force not exceeding 60 pounds (see 4.7.1.4).
3
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
3.8.7 Strap strength. The strap shall have a minimum tensile strength of 9,500 pounds (see 4.7.3).
3.9 Environmental conditions. The tie down shall be capable of satisfactory operation in worldwide
environmental conditions expected to be encountered during aircraft loading operations and long term storage to
include the following conditions:
3.10 Durability. The tie down shall be designed to perform in its intended environment (see 3.9) for at least 30
years of continuous use with no loss of function or safety (see 4.7.5).
3.11 Interchangeability. All parts having the same manufacturers part number shall be functionally and
dimensionally interchangeable (see 4.6).
3.12 Item identification. The tie down major components (strap, fixed hook, and adjustable hook assemblies)
shall be permanently marked for identification in accordance with MIL-STD-130. The identification shall include
the contract number, vendor, and CAGE number (see 4.6). The following special marking shall be included:
3.13 Safety. The tie downs shall be functional without sharp edges, burrs, or protrusions that might injure
operational personnel or prevent the operation of the tie downs in restricted locations. Operation of the tie down
equipment shall not present undue hazards to personnel, wearing standard aircrew work gloves, during tie down of
cargo, while the cargo is secured, during the release of cargo restraint, or during removal or stowage of the tie
downs. Normal operation shall not present cutting, pinching, stabbing, nor abrupt impact hazards to personnel.
Tie down straps shall not contain defects such as holes, cuts, tears, splices, or abrasions which may cause strap
failure and result in injury to personnel. The strap shall also be free of grease, oil, dirt, or any other foreign matter
that is not removable without damaging the strap and degrading its strength (see 4.6).
3.14 Toxic chemicals, hazardous substances, and ozone depleting chemicals (ODCs). The use of toxic
chemicals, hazardous substances, or ODCs shall be avoided (see 4.6).
4. VERIFICATION
4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:
4.1.1 Sampling for inspection. Unless otherwise specified, sampling shall be in accordance with ANSI/ASQC
Z1.4.
4
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
4.2 Qualification inspection. Qualification inspection shall be performed on three complete tie down
assemblies (A, B, and C). The three tie down assemblies will be examined in accordance with 4.6. The assemblies
will then be subjected to the tests specified in 4.7 using the sequence specified in table I.
4.3 Conformance inspection. Conformance inspection shall include the examinations and inspections under
4.6, and the tests specified (see 4.7.1.3 and 4.7.1.5).
4.4 Test conditions. Unless otherwise specified, all inspections shall be performed in accordance with the test
conditions specified in RTCA/DO-160 for the applicable test.
4.5 Requirements cross-reference matrix. Table II provides a cross-reference matrix of the section 3
requirements and section 4 verifications.
4.6 Visual examination. Each tie down assembly shall be examined for compliance with the requirements
specified (see 3.3, 3.4, 3.5, 3.5.1, 3.5.2, 3.5.3, 3.6.1, 3.6.2, 3.6.3, 3.6.4, 3.11, 3.12, 3.13, and 3.14).
4.7.1 Sample configuration. Unless otherwise specified, tests shall be made with the tie down working length
adjusted to 4 feet 3 inches.
4.7.1.1 Operations. The test shall be performed in conjunction with the tensioning (see 4.7.1.2) and the release
(see 4.7.1.4) tests as specified (see 3.7).
4.7.1.2 Adjusting and tensioning mechanism. With the tie down connected between two fixed points 18 feet
apart, the adjusting mechanism and tensioning mechanism shall be operated and checked for compliance (see 3.8.3
and 3.8.4).
4.7.1.3 Tensioning mechanism strength. The tensioning mechanism shall be subjected to a minimum applied
force of 300 pounds through the operating lever. The tensioning mechanism shall be operated and checked for
compliance (see 3.8.5).
4.7.1.4 Release mechanism. The tie down shall be assembled in a testing machine and the release mechanism
locked. A minimum load of 750 pounds shall be applied and the release mechanism shall operate by the
application of not more than 60 pounds of force, while the tie down is sustaining the applied load. The release
mechanism shall operate as specified (see 3.8.6).
4.7.2 Environmental. Environmental testing shall be planned and conducted using the guidance in RTCA/DO-
160.
4.7.2.1 Fungus resistance. The tie downs shall be subject to a fungus resistance test in accordance with
RTCA/DO-160, Section 13, Category F.
4.7.2.2 Salt fog. The tie down shall be subjected to a salt fog test in accordance with RTCA/DO-160, Section 14,
Category S, 5% Salt Spray. At the conclusion of this test, the tie down shall be subjected to the tests specified (see
4.7.1.2, 4.7.1.3, and 4.7.1.4).
4.7.2.3 Sand and dust. The tie down shall be subjected to a dust test in accordance with RTCA/DO-160, Section
12, Category D. Note: if 140 mesh silica flour is used, local environmental laws and criteria must be observed. At
the conclusion of this test, the tie down shall be subjected to the tests specified (see 4.7.1.2 and 4.7.1.4).
5
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
4.7.2.4 Vibration. The tie down shall be kept under a tension of 200 pounds for a 24-hour period. The tie down
assembly, while under tension, shall then be subjected to a vibration test in accordance with RTCA/DO-160,
Section 8, Standard Sinusoidal Vibration Test Procedure, Figure 8-4, Curve Y.
4.7.2.5 Low temperature. The tie down shall be subjected to a low temperature test in accordance with
RTCA/DO-160 Section 4, Category A3, Ground Survival Low Temperature Curve, and temperature of -65F.
During this test, the tie down shall be subjected to the tests specified (see 4.7.1.2, 4.7.1.3, and 4.7.1.4).
4.7.2.6 High temperature. The tie down shall be subjected to a high temperature test in accordance with
RTCA/DO-160 Section 4, Category A3, Ground Survival High Temperature Curve, except the maximum
temperature shall be 160F. During this test, the tie down shall be subjected to the tests specified (see 4.7.1.2,
4.7.1.3, and 4.7.1.4).
4.7.3 Strap strength. The strap material shall be tested to failure in a tensile test machine at a constant
crosshead rate of 3.0 1.0 inches per minute in order to verify compliance (see 3.8.7).
4.7.4 Proof-load. The tie down shall be subjected to a proof load of 5,000 pounds for 30 seconds as specified
(see 3.8.1).
4.7.4.1 Ultimate-load. The tie down shall be subjected to an ultimate load of 6,000 pounds for 30 seconds as
specified (see 3.8.2).
4.7.5 Durability. One tie down shall be rotated for one hour in a tumbler type test fixture. The tie down will
then be subjected to the tests specified (see 4.7.1.2 and 4.7.1.4).
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or
order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to
contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements
are maintained by the Inventory Control Point packaging activity within the Military Department or Defense
Agency, or within the Military Departments System Command. Packaging data retrieval is available from the
managing Military Department or Defense Agency automated packaging files, CD-ROM products, or by contacting
the responsible packaging activity.
6. NOTES
(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)
6.1 Intended use. The CGU-1/B tie down covered by this specification is intended for use in securing cargo
being transported in military aircraft.
b. Issue of the DoDISS to be cited in the solicitation, and if required, the specific issue of individual
documents referenced (see 2.3).
6
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
6.3 Qualification. The attention of the contractors is called to the requirements with respect to products
requiring qualification. Awards will be made only for products which are, at the time of award of contract,
qualified for inclusion in the Qualified Products List (QPL-27260) whether or not such products have actually been
listed by that date. In order that the manufacturers may be eligible to be awarded contracts or purchase orders for
the products covered by this specification, they are urged to arrange to have the products that they propose to offer
to the Federal Government tested for qualification. Information pertaining to qualification of products may be
obtained from (Resources & Logistics Services Division, SA-ALC/TILDD, 485 Quentin Roosevelt Rd., Kelly AFB,
Texas 78241-6425).
6.5 Changes from previous issue. Marginal notations are not used in this revision to identify changes with
respect to the previous issue due to the extent of the changes.
7
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
8
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
9
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
MIL-PRF-27260C
10
Source: http://www.assistdocs.com -- Downloaded: 2011-09-29T16:38Z
Check the source to verify that this is the current version before use.
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL
INSTRUCTIONS
1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision letter should be
given.
2. The submitter of this form must complete blocks 4, 5, 6, and 7.
3. The preparing activity must provide a reply within 30 days from receipt of the form.
NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current
contracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced
document(s) or to amend contractual requirements.
1. DOCUMENT NUMBER 2. DOCUMENT DATE (YYMMDD)
I RECOMMEND A CHANGE:
MIL-PRF-27260C 27 Nov 98
3. DOCUMENT TITLE
Tie Down, Cargo, Aircraft, CGU-1/B
4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.)
6. SUBMITTER
a. NAME (Last, First, Middle Initial) b. Organization
c. ADDRESS (Include zip code) d. TELEPHONE (Include Area Code) 7. DATE SUBMITTED
(1) Commercial (YYMMDD)
(2) DSN
(if applicable)
8. PREPARING ACTIVITY
a. NAME b. TELEPHONE (Include Area Code)
SA-ALC/TILDD (1) Commercial (2) DSN
210-925-6314 945-6314
c. ADDRESS (Include Zip Code) IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS,
485 Quentin Roosevelt Rd. CONTACT:
Kelly AFB, Texas 78241-6425 Defense Quality and Standardization Office
5203 Leesburg Pike, Suite 1403, Falls Church, VA 22041-
3466
Telephone (703) 756-2340 DSN 289-2340
DD Form 1426, OCT 89 Previous editions are obsolete. 198/290