Manual Onkyo TX-SR608

Contents
AV Receiver Introduction ...................................2
TX-SR608 Connections.................................13
Turning On & Basic Operations ......22
Instruction Manual Advanced Operations .................38
Controlling iPod & Other

Components............................58
Others...........................................66
Thank you for purchasing an Onkyo AV Receiver.

Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
En
WARNING: WARNING AVIS
RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE
TO REDUCE THE RISK OF FIRE OR ELECTRIC DO NOT OPEN NE PAS OUVRIR
SHOCK, DO NOT EXPOSE THIS APPARATUS TO
The lightning flash with arrowhead symbol, within an
RAIN OR MOISTURE.
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
CAUTION: the product’s enclosure that may be of sufficient
TO REDUCE THE RISK OF ELECTRIC SHOCK, magnitude to constitute a risk of electric shock to
DO NOT REMOVE COVER (OR BACK). NO persons.
USER-SERVICEABLE PARTS INSIDE. REFER The exclamation point within an equilateral triangle is
SERVICING TO QUALIFIED SERVICE intended to alert the user to the presence of important
PERSONNEL. operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions

1. Read these instructions. 15. Damage Requiring Service
2. Keep these instructions. Unplug the apparatus from the wall outlet and refer
3. Heed all warnings. servicing to qualified service personnel under the fol-
4. Follow all instructions. lowing conditions:
5. Do not use this apparatus near water. A. When the power-supply cord or plug is damaged,
6. Clean only with dry cloth. B. If liquid has been spilled, or objects have fallen
7. Do not block any ventilation openings. Install in into the apparatus,
accordance with the manufacturer’s instructions. C. If the apparatus has been exposed to rain or water,
8. Do not install near any heat sources such as radiators, D. If the apparatus does not operate normally by fol-
heat registers, stoves, or other apparatus (including lowing the operating instructions. Adjust only
amplifiers) that produce heat. those controls that are covered by the operating
9. Do not defeat the safety purpose of the polarized or instructions as an improper adjustment of other
grounding-type plug. A polarized plug has two blades controls may result in damage and will often
with one wider than the other. A grounding type plug require extensive work by a qualified technician to
has two blades and a third grounding prong. The wide restore the apparatus to its normal operation,
blade or the third prong are provided for your safety. If E. If the apparatus has been dropped or damaged in
the provided plug does not fit into your outlet, consult any way, and
an electrician for replacement of the obsolete outlet. F. When the apparatus exhibits a distinct change in
10. Protect the power cord from being walked on or performance this indicates a need for service.
pinched particularly at plugs, convenience receptacles, 16. Object and Liquid Entry
and the point where they exit from the apparatus. Never push objects of any kind into the apparatus
11. Only use attachments/accessories specified by the through openings as they may touch dangerous volt-
manufacturer. age points or short-out parts that could result in a fire
12. Use only with the cart, stand, PORTABLE CART WARNING or electric shock.
tripod, bracket, or table speci- The apparatus shall not be exposed to dripping or
fied by the manufacturer, or splashing and no objects filled with liquids, such as
sold with the apparatus. When vases shall be placed on the apparatus.
a cart is used, use caution Don’t put candles or other burning objects on top of
when moving the cart/appara- this unit.
tus combination to avoid 17. Batteries
S3125A
injury from tip-over. Always consider the environmental issues and follow
13. Unplug this apparatus during lightning storms or when local regulations when disposing of batteries.
unused for long periods of time. 18. If you install the apparatus in a built-in installation,
14. Refer all servicing to qualified service personnel. Ser- such as a bookcase or rack, ensure that there is ade-
vicing is required when the apparatus has been dam- quate ventilation.
aged in any way, such as power-supply cord or plug is Leave 20 cm (8") of free space at the top and sides and
damaged, liquid has been spilled or objects have fallen 10 cm (4") at the rear. The rear edge of the shelf or
into the apparatus, the apparatus has been exposed to board above the apparatus shall be set 10 cm (4")
rain or moisture, does not operate normally, or has away from the rear panel or wall, creating a flue-like
been dropped. gap for warm air to escape.
En
2
Precautions
1. Recording Copyright—Unless it’s for personal use For U.S. models
only, recording copyrighted material is illegal without
FCC Information for User
the permission of the copyright holder.
CAUTION:
2. AC Fuse—The AC fuse inside the unit is not user-ser-
viceable. If you cannot turn on the unit, contact your The user changes or modifications not expressly approved
Onkyo dealer. by the party responsible for compliance could void the
3. Care—Occasionally you should dust the unit all over user’s authority to operate the equipment.
with a soft cloth. For stubborn stains, use a soft cloth NOTE:
dampened with a weak solution of mild detergent and This equipment has been tested and found to comply with
water. Dry the unit immediately afterwards with a the limits for a Class B digital device, pursuant to Part 15
clean cloth. Don’t use abrasive cloths, thinners, alco- of the FCC Rules. These limits are designed to provide
hol, or other chemical solvents, because they may reasonable protection against harmful interference in a
damage the finish or remove the panel lettering. residential installation.
4. Power This equipment generates, uses and can radiate radio fre-
WARNING quency energy and, if not installed and used in accordance
BEFORE PLUGGING IN THE UNIT FOR THE with the instructions, may cause harmful interference to
FIRST TIME, READ THE FOLLOWING SECTION radio communications. However, there is no guarantee
CAREFULLY. that interference will not occur in a particular installation.
AC outlet voltages vary from country to country. If this equipment does cause harmful interference to radio
Make sure that the voltage in your area meets the volt- or television reception, which can be determined by turn-
age requirements printed on the unit’s rear panel (e.g., ing the equipment off and on, the user is encouraged to try
AC 230 V, 50 Hz or AC 120 V, 60 Hz). to correct the interference by one or more of the following
The power cord plug is used to disconnect this unit measures:
from the AC power source. Make sure that the plug is • Reorient or relocate the receiving antenna.
readily operable (easily accessible) at all times. • Increase the separation between the equipment and
Pressing ON/STANDBY to select Standby mode does receiver.
not fully shutdown the unit. If you do not intend to use • Connect the equipment into an outlet on a circuit differ-
the unit for an extended period, remove the power cord ent from that to which the receiver is connected.
from the AC outlet. • Consult the dealer or an experienced radio/TV techni-
5. Preventing Hearing Loss cian for help.
Caution
Excessive sound pressure from earphones and head- For Canadian Models
phones can cause hearing loss. NOTE: THIS CLASS B DIGITAL APPARATUS COM-
6. Batteries and Heat Exposure PLIES WITH CANADIAN ICES-003.
Warning For models having a power cord with a polarized plug:
Batteries (battery pack or batteries installed) shall not
CAUTION: TO PREVENT ELECTRIC SHOCK,
be exposed to excessive heat as sunshine, fire or the
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
like.
FULLY INSERT.
7. Never Touch this Unit with Wet Hands—Never han-
dle this unit or its power cord while your hands are Modèle pour les Canadien
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer. REMARQUE: CET APPAREIL NUMÉRIQUE DE
8. Handling Notes LA CLASSE B EST CONFORME À LA NORME NMB-
• If you need to transport this unit, use the original 003 DU CANADA.
packaging to pack it how it was when you originally Sur les modèles dont la fiche est polarisée:
bought it. ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
• Do not leave rubber or plastic items on this unit for TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
a long time, because they may leave marks on the DE LA FICHE DANS LA BORNE CORRESPON-
case. DANTE DE LA PRISE ET POUSSER JUSQU’AU
• This unit’s top and rear panels may get warm after FOND.
prolonged use. This is normal.
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
En
3
For British models Supplied Accessories
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by qual-
Make sure you have the following accessories:
ified service personnel.
Indoor FM antenna (➔ 20)
IMPORTANT
AM loop antenna (➔ 20)
The wires in the mains lead are coloured in accordance
Speaker cable labels (➔ 13)
with the following code:
Speaker setup microphone (➔ 26)
Blue: Neutral
Remote controller and two batteries (AA/R6)
Brown: Live (Note for China: The battery for the remote controller is not sup-
As the colours of the wires in the mains lead of this appa- plied for this unit.)
ratus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows: * In catalogs and on packaging, the letter at the end of the prod-
uct name indicates the color. Specifications and operations are
The wire which is coloured blue must be connected to the
the same regardless of color.
terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to Using the Remote Controller
the terminal which is marked with the letter L or coloured
red. Installing the Batteries
IMPORTANT Note
The plug is fitted with an appropriate fuse. If the fuse • If the remote controller
doesn’t work reliably, try
needs to be replaced, the replacement fuse must approved
replacing the batteries.
by ASTA or BSI to BS1362 and have the same ampere rat-
• Don’t mix new and old
ing as that indicated on the plug. Check for the ASTA batteries or different
mark or the BSI mark on the body of the fuse. types of batteries.
If the power cord’s plug is not suitable for your socket out- • If you intend not to use Batteries (AA/R6)
lets, cut it off and fit a suitable plug. Fit a suitable fuse in the remote controller for
the plug. a long time, remove the batteries to prevent damage from leak-
age or corrosion.
• Remove expired batteries as soon as possible to prevent damage
For European Models from leakage or corrosion.
Declaration of Conformity Aiming the Remote Controller

We, ONKYO EUROPE
ELECTRONICS GmbH
To use the remote controller, point it at the AV receiver’s
LIEGNITZERSTRASSE 6, remote control sensor, as shown below.
82194 GROEBENZELL,
GERMANY Remote control sensor
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the AV receiver
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
Approx. 16 ft. (5 m)
En
4
Contents
Introduction Advanced Operations
Important Safety Instructions ......................................... 2 Advanced Setup ............................................................. 38
Precautions....................................................................... 3 On-screen Setup Menus............................................... 38
Supplied Accessories...................................................... 4 Common Procedures in Setup Menu ........................... 38
Using the Remote Controller .......................................... 4 Input/Output Assign ...................................................... 39
Features ............................................................................ 6 Speaker Setup.............................................................. 40
Front & Rear Panels......................................................... 8 Audio Adjust ................................................................. 44
Front Panel..................................................................... 8
Source Setup................................................................ 45
Display............................................................................ 9
Listening Mode Preset.................................................. 49
Rear Panel ................................................................... 10 Miscellaneous ............................................................... 50
Remote Controller.......................................................... 11
Hardware Setup............................................................ 50
Controlling the AV Receiver ......................................... 11
Lock Setup.................................................................... 52
About Home Theater...................................................... 12
Using the Audio Settings .............................................. 52
Enjoying Home Theater................................................ 12
Adjusting the Bass & Treble ......................................... 54
Zone 2.............................................................................. 55
Connections Connecting Zone 2 ....................................................... 55
Connecting the AV Receiver ......................................... 13 Setting the Powered Zone 2 ......................................... 56
Connecting Your Speakers .......................................... 13 Using Zone 2 ................................................................ 56
About AV Connections ................................................. 16
Connecting Components with HDMI ............................ 17 Controlling iPod & Other Components
Connecting External Components................................ 18
Controlling iPod ............................................................. 58
Connecting Onkyo u Components ............................ 20
Connecting an Onkyo Dock .......................................... 58
Connecting Antenna..................................................... 20
Using the Onkyo Dock .................................................. 59
Which Connections Should I Use?............................... 21
Controlling Your iPod.................................................... 60
Controlling Other Components..................................... 62
Turning On & Basic Operations Preprogrammed Remote Control Codes ...................... 62
Looking up for Remote Control Code ........................... 62
Turning On/Off the AV Receiver ................................... 22
Turning On ................................................................... 22 Entering Remote Control Codes................................... 63
Turning Off ................................................................... 22 Remote Control Codes for
Basic Operations............................................................ 23 Onkyo Components Connected via u ..................... 63
Selecting the Language Used for Resetting REMOTE MODE Buttons ............................. 64
the Onscreen Setup Menus ....................................... 23 Resetting the Remote Controller .................................. 64
Playing the Connected Component.............................. 23 Controlling Other Components ..................................... 64
Displaying Source Information ..................................... 23
Setting the Display Brightness ..................................... 23 Others
Muting the AV Receiver................................................ 24
Using the Sleep Timer.................................................. 24 Troubleshooting ............................................................. 66
Specifications ................................................................. 71
Selecting Speaker Layout ............................................ 24
About HDMI ..................................................................... 72
Using the Home Menu.................................................. 24 Using an RIHD-compatible TV, Player, or Recorder ... 73
Changing the Input Display .......................................... 25 Video Resolution Chart.................................................. 75
Using Headphones....................................................... 25
Audyssey 2EQ® Room Correction and
Speaker Setup ........................................................... 25 To reset the AV receiver to its factory defaults, turn it
Listening to the Radio ................................................... 28 on and, while holding down VCR/DVR, press
Using the Tuner............................................................ 28 ON/STANDBY (➔ 66).
Presetting FM/AM Stations........................................... 29
Using RDS (excluding North American models) .......... 29
Recording ....................................................................... 31
Using the Listening Modes ........................................... 32
Selecting Listening Modes ........................................... 32
About Listening Modes................................................. 33
En
5
Features
Amplifier Miscellaneous
• 100 Watts/Channel @ 8 ohms (FTC) • 40 SIRIUS*9/FM/AM Presets (North American mod-
• 160 Watts/Channel @ 6 ohms (IEC) els)
• 175 Watts/Channel @ 6 ohms (JEITA) • 40 FM/AM Presets (excluding North American mod-
• WRAT–Wide Range Amplifier Technology els)
(5 Hz to 100 kHz bandwidth) • Audyssey 2EQ®*4 to Correct Room Acoustic Problems
• Optimum Gain Volume Circuitry • Audyssey Dynamic EQ™*4 for Loudness Correction
• H.C.P.S. (High Current Power Supply) Massive High • Audyssey Dynamic Volume™*4 to Maintain Optimal
Power Transformer Listening Level and Dynamic Range
• Jitter Cleaning Circuit Technology • Crossover Adjustment
(40/50/60/70/80/90/100/120/150/200 Hz)
Processing • A/V Sync Control Function (up to 200 ms)
• On-Screen Display via HDMI
• THX Select2 Plus*1 Certified
• HDMI Video Upscaling (to 1080p Compatible) with • Preprogrammed u-Compatible Remote
*1
Faroudja DCDi Cinema Enhancement
• HDMI (Ver.1.4 with Audio Return Channel, 3D), Deep- THX and the THX logo are trademarks of THX Ltd. which
Color, x.v.Color*, Lip Sync, DTS*2-HD Master Audio, may be registered in some jurisdictions. All rights reserved.
DTS-HD High Resolution Audio, Dolby TrueHD*3, *2
Dolby Digital Plus, DSD and Multi-CH PCM
• Dolby Pro Logic IIz*3 – New Surround Format (front- Manufactured under license under U.S. Patent #’s: 5,451,942;
high) 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;
• Audyssey DSX™*4 for New Surround Channels (front- 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and
wide/front-high) worldwide patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-HD and DTS-
• Non-Scaling Configuration HD Master Audio are trademarks of DTS, Inc.
• A-Form Listening Mode Memory ©1996-2008 DTS, Inc. All Rights Reserved.
• Direct Mode *3
• Pure Audio Mode (European, Australian and Asian
models)
• Music Optimizer*5 for Compressed Digital Music files Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX” and the double-D sym-
• 192 kHz/24-bit D/A Converters bol are trademarks of Dolby Laboratories.
• Powerful and Highly Accurate 32-bit Processing DSP *4
Connections
Manufactured under license from Audyssey Laboratories™.
• 6 HDMI*6 Inputs (1 on front panel) and 1 Output
U.S. and foreign patents pending. Audyssey 2EQ®,
• Onkyo p for System Control Audyssey DSX™, Audyssey Dynamic Volume™ and
• 4 Digital Inputs (2 Optical/2 Coaxial) Audyssey Dynamic EQ™ are trademarks of
• Component Video Switching (2 Inputs/1 Output) Audyssey Laboratories.
*5 Music Optimizer™ is a trademark of Onkyo Corporation.
• Front “Line in” Input for Portable audio player
*6
• Universal Port for the Dock for iPod*/HD Radio™*7
tuner module (North American models)/DAB+ tuner “HDMI, the HDMI Logo, and High-Definition Multimedia
module (European, Australian and Asian models) Interface are trademarks or registered trademarks of HDMI
• Banana Plug-Compatible Speaker Posts*8 Licensing LLC in the United States and other countries.”
• Powered Zone 2 *7
• Bi-Amping Capability for FL/FR with SBL/SBR
• Analog RGB Video Input (D-sub 15) for PC The HD Radio Ready logo is a proprietary trademark of iBiq-
uity Digital Corp.
To receive HD Radio broadcasts, you must install an Onkyo
UP-HT1 HD Radio tuner module (sold separately).
*8 In Europe, using banana plugs to connect speakers to an audio
amplifier is prohibited.
En
6
*9
SIRIUS, XM and all related marks and logos are trademarks

of Sirius XM Radio Inc. and its subsidiaries. All other marks
and logos are the property of their respective owners. All
rights reserved. SIRIUS subscription sold separately. Taxes
and a one-time activation fee may apply. SIRIUS tuner
required (sold separately) to receive the SIRIUS service. All
programming and fees subject to change. It is prohibited to
copy, decompile, disassemble, reverse engineer, hack, manip-
ulate or otherwise make available any technology or software
incorporated in receivers compatible with the SIRIUS Satel-
lite Radio System. Service not available in Alaska or Hawaii.
THX Select2 Plus

Before any home theater component can be THX
Select2 Plus certified, it must pass a rigorous series of
quality and performance tests. Only then can a product
feature the THX Select2 Plus logo, which is your guar-
antee that the Home Theater products you purchase
will give you superb performance for many years to
come. THX Select2 Plus requirements define hundreds
of parameters, including power amplifier performance,
and pre-amplifier performance and operation for both
digital and analog domains. THX Select2 Plus receiv-
ers also feature proprietary THX technologies (e.g.,
THX Mode) which accurately translate movie
soundtracks for home theater playback.
* Apple and iPod are trademarks of Apple Inc., registered in the
U.S. and other countries.
* “x.v.Color” is a trademark of Sony Corporation.
En
7
Front & Rear Panels
Front Panel
North American and Taiwan models
a b cd e f g h i j klm n o p
q r s t u v w
European, Australian and Asian models
x y
The actual front panel has various logos printed on it. They are not shown here for clarity.
The page numbers in parentheses show where you can find the main explanation for each item.
a ON/STANDBY button (➔ 22) n TUNING, PRESET (➔ 28 to 29), arrow and

b STANDBY indicator (➔ 22) ENTER buttons
c HDMI THRU indicator (➔ 52) o RETURN button
d ZONE 2 indicator (➔ 56) p MASTER VOLUME control (➔ 23)
e Remote control sensor (➔ 4) q PHONES jack (➔ 25)
f ZONE 2, OFF, ZONE 2 LEVEL/TONE LEVEL r AUX INPUT HDMI jack (➔ 17)
and TONE buttons (➔ 54, 56 to 57) s Input selector buttons (➔ 23)
g Display (➔ 9) t AUX INPUT LINE IN jack (➔ 18)
h LISTENING MODE buttons (➔ 32) u AUX INPUT VIDEO jack (➔ 18)
i DIMMER button (North American and Taiwan v AUX INPUT AUDIO jacks (➔ 18)
models) (➔ 23) w SETUP MIC jack (➔ 26)
j MEMORY button (➔ 29) x PURE AUDIO button and indicator (European,
k TUNING MODE button (➔ 28) Australian and Asian models) (➔ 32)
l DISPLAY button (➔ 23) y RT/PTY/TP button (European, Australian and
En m SETUP button (➔ 38) Asian models) (➔ 29)
8
Display
a b c d e f
For detailed information, see the pages in parentheses.

a Audio input indicators e RDS indicator (excluding North American models)
b Listening mode and format indicators (➔ 32, 53) (➔ 29)
c Audyssey indicators (➔ 25, 45) f SLEEP indicator (➔ 24)
d Tuning indicators (➔ 28) g MUTING indicator (➔ 24)
h Message area
En
9
Rear Panel
North American and Taiwan models
a bc d e fg h i
jk l mn o
o h
a DIGITAL IN COAXIAL and OPTICAL jacks k SIRIUS antenna jack (North American models)
b COMPONENT VIDEO IN and OUT jacks l Composite video and analog audio jacks
c HDMI IN and OUT jacks (BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,
d PC IN jack GAME IN, PC IN, TV/CD IN)
e FM ANTENNA jack and AM ANTENNA terminal m ZONE 2 LINE OUT jacks
f MONITOR OUT V jack n SUBWOOFER PRE OUT jacks
g UNIVERSAL PORT jack o FRONT HIGH OR FRONT WIDE OR ZONE 2

SPEAKERS terminals
h SPEAKERS terminals
(CENTER, FRONT, SURR, SURR BACK OR See “Connecting the AV Receiver” for connection infor-
FRONT HIGH OR FRONT WIDE) mation (➔ 13 to 21).
i Power cord
j u REMOTE CONTROL jack
En
10
Remote Controller
Controlling the AV Receiver
To control the AV receiver, press RECEIVER to select

Receiver mode.
a h You can also use the remote controller to control
c Onkyo Blu-ray Disc/DVD player, CD player, and
other components.
b See “Entering Remote Control Codes” for more
details (➔ 63).
i For detailed information, see the pages in parentheses.

a ON/STANDBY button (➔ 22)
b REMOTE MODE/INPUT SELECTOR buttons
j (➔ 23)
c SP LAYOUT button (➔ 24)
d
d Arrow q/w/e/r and ENTER buttons
c *1
e SETUP button (➔ 38)
d f LISTENING MODE buttons (➔ 32)
a g DIMMER button (➔ 23)
e k h DISPLAY button (➔ 24)
i MUTING button (➔ 24)
l j VOL q/w button (➔ 23)
k RETURN button
l HOME button (➔ 24)
m SLEEP button (➔ 24)
f ■ Controlling the tuner

To control the AV receiver’s tuner, press TUNER (or
RECEIVER).
e You can select AM or FM by pressing TUNER repeatedly.
a Arrow q/w buttons (➔ 28)
b D.TUN button (➔ 28)
g c DISPLAY button
m
b d CH +/– button (➔ 29)
e Number buttons (➔ 28)
*1 VIDEO functions as a short cut of HOME.
En
11
About Home Theater
Enjoying Home Theater
Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your
own home—just like being in a movie theater or concert hall. With Blu-ray Discs, you can enjoy DTS and Dolby Digital.
With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.
You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).
a Front speakers
These output the overall sound. Their role in a home theater is to provide
a solid anchor for the sound image. They should be positioned facing the
a be fg listener at about ear level, and equidistant from the TV. Angle them inward
so as to create a triangle, with the listener at the apex.
b Center speaker
This speaker enhances the front speakers, making sound movements dis-
tinct and providing a full sound image. In movies it’s used mainly for dia-
log. Position it close to your TV facing forward at about ear level, or at the
same height as the front speakers.
c Surround speakers
These speakers are used for precise sound positioning and to add realistic
ambience. Position them at the sides of the listener, or slightly behind,
about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they should be
equidistant from the listener.
d Surround back speakers
These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix,
DTS-ES Discrete, THX Surround EX, etc. They enhance the realism of
surround sound and improve sound localization behind the listener. Posi-
cd tion them behind the listener about 2 to 3 feet (60 to 100 cm) above ear
level.
e Front high speakers
These speakers are necessary to enjoy Dolby Pro Logic IIz Height, and
Audyssey DSX™. They significantly enhance the spatial experience.
Position them at least 3.3 feet (100 cm) above the front speakers (prefera-
bly as high as possible) and at an angle slightly wider than the front speak-
ers.
Corner f Front wide speakers
position These speakers are necessary to enjoy Audyssey DSX. They significantly
enhance the spatial experience. Position them well outside of the front
speakers. See also http://www.audyssey.com/technology/dsx.html about
1/3 of wall
optimum speaker placement for Audyssey DSX.
position
g Subwoofer
Tip The subwoofer handles the bass sounds of the LFE (Low-Frequency
Effects) channel. The volume and quality of the bass output from your
• To find the best position for your subwoofer, while
subwoofer will depend on its position, the shape of your listening room,
playing a movie or some music with good bass,
and your listening position. In general, a good bass sound can be obtained
experiment by placing your subwoofer at various
by installing the subwoofer in a front corner, or at one-third the width of
positions within the room, and choose the one that
the wall, as shown.
provides the most satisfying results.
En
12
Connecting the AV Receiver
Connecting Your Speakers Speaker Connection Precautions
Read the following before connecting your speakers:
Speaker Configuration • (North American and Taiwan models) You can con-
The following table indicates the channels you should use nect speakers with an impedance of between 6 and 16
depending on the number of speakers that you have. ohms. If you use speakers with a lower impedance, and
For 7.1-channel surround-sound playback, you need seven use the amplifier at high volume levels for a long period
speakers and a powered subwoofer. of time, the built-in amp protection circuit may be acti-
vated.
Number of channels 2 3 4 5 6 7 7 7 8 8 9 9 9 • (European, Australian and Asian models) You can
Front speakers ✔✔✔✔✔✔✔✔✔✔✔✔✔ connect speakers with an impedance of between 4 and
Center speaker ✔ ✔✔✔✔✔✔✔✔✔✔ 16 ohms. If the impedance of any of the connected
Surround speakers ✔✔✔✔✔✔✔✔✔✔✔
speakers is 4 ohms or more, but less than 6 ohms, be sure
to set the minimum speaker impedance to “4ohms”
Surround back ✔ ✔✔
speaker*1*2 (➔ 40). If you use speakers with a lower impedance, and
use the amplifier at high volume levels for a long period
Surround back ✔ ✔✔
speakers*2 of time, the built-in protection circuit may be activated.
Front high speakers*2 ✔ ✔ ✔ ✔ • Disconnect the power cord from the wall outlet before
making any connections.
Front wide speakers*2 ✔ ✔ ✔✔
• Read the instructions supplied with your speakers.
*1 If you’re using only one surround back speaker, connect it to • Pay close attention to speaker wiring polarity. In other
the SURR BACK OR FRONT HIGH OR FRONT WIDE L words, connect positive (+) terminals only to positive (+)
terminals. terminals, and negative (–) terminals only to negative (–)
*2 Front high, surround back and front wide speakers cannot be terminals. If you get them the wrong way around, the
used at the same time. sound will be out of phase and will sound unnatural.
No matter how many speakers you use, a powered sub- • Unnecessarily long, or very thin speaker cables may
woofer is recommended for a really powerful and solid affect the sound quality and should be avoided.
bass.
• Be careful not to short the positive and negative wires.
To get the best from your surround sound system, you Doing so may damage the AV receiver.
need to set the speaker settings. You can do this automati-
• Make sure the metal core of the wire does not have con-
cally (➔ 26) or manually (➔ 40).
tact with the AV receiver’s rear panel. Doing so may
damage the AV receiver.
Attaching the Speaker Cable Labels
The AV receiver’s positive (+) speaker terminals are all
red (the negative (–) speaker terminals are all black).
Speaker Color
Front left, Front high left, Front wide left White
Front right, Front high right, Front wide right Red
Center Green
Surround left Blue
Surround right Gray
Surround back left, Zone 2 left Brown
Surround back right, Zone 2 right Tan
The supplied speaker cable labels are also color-coded and

you should attach them to the positive (+) side of each
speaker cable in accordance with the table above. Then all
you need to do is to match the color of each label to the
corresponding speaker terminal.
En
13
• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
Connecting the Speaker Cables

Screw-type speaker terminals
Strip 1/2" to 5/8" (12 to 15 mm) of 1/2" to 5/8"(12 to 15 mm)
insulation from the ends of the
speaker cables, and twist the bare
wires tightly, as shown.
Using Banana Plugs (North American models)

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.
• Do not insert the speaker code directly into the center hole of the speaker terminal.
Push-type speaker terminals

Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends of 3/8" to 1/2"(10 to 12 mm)
the speaker cables, and twist the bare wires tightly, as shown.
The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one
surround back speaker, connect it to the SURR BACK OR FRONT HIGH OR FRONT WIDE L terminals.
North American and Taiwan models Surround Surround Surround Surround

back right back left right left
speaker speaker speaker speaker
Front high Front high Front high Front high Front right Front left Center
right speaker/ left speaker/ right speaker/ left speaker/ speaker speaker speaker
Front wide Front wide Front wide Front wide
right speaker left speaker right speaker left speaker
Note
• The front wide speakers can also be connected to the FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals. When
doing so, set “Front High/Front Wide/Zone2” in Speaker Setup to “Front Wide” (➔ 41).
En • The front high or front wide speakers can also be connected to the SURR BACK OR FRONT HIGH OR FRONT WIDE SPEAK-
ERS terminals. When doing so, set “Surr Back/Front High/Front Wide” in Speaker Setup to “Front High” or “Front Wide” (➔ 41).
14
Using Dipole Speakers
Dipole speakers Normal speakers
You can use dipole speakers for the surround and surround
e e e e
back speakers. Dipole speakers output the same sound in two
directions. g g g
TV/screen g TV/screen
Dipole speakers typically have an arrow printed on them to
f a b a f f a b a f
indicate how they should be positioned. The surround dipole
speakers should be positioned so that their arrows point
toward the TV/screen, while the surround back dipole speak-
ers should be positioned so that their arrows point toward
each other, as shown. c c c c
a Front speakers
b Center speaker
c Surround speakers
d d d d
f Front wide speakers
g Subwoofers
Connecting a Powered Subwoofer
Using a suitable cable, connect the AV receiver’s

SUBWOOFER PRE OUT jack to an input on Powered subwoofer
your powered subwoofer, as shown. If your sub-
woofer is unpowered and you’re using an external
amplifier, connect the SUBWOOFER PRE OUT L E N T NE P T
jack to an input on the amp.

You can connect the powered subwoofer with two
SUBWOOFER PRE OUT jacks respectively.
The same signal is output from each jack. LINE INPUT
LINE INPUT
Bi-amping the Front Speakers
The FRONT L/R and SURR BACK OR FRONT

HIGH OR FRONT WIDE L/R terminal posts can be
used with front speakers and surround back speakers
respectively, or bi-amped to provide separate tweeter
and woofer feeds for a pair of front speakers that sup-
port bi-amping, providing improved bass and treble per-
formance.
• When bi-amping is used, the AV receiver is able to
drive up to a 5.1 speaker system in the main room.
Right Left
• For bi-amping, the FRONT L/R terminal posts con- speaker speaker
nect to the front speakers’ woofer terminals; the
SURR BACK OR FRONT HIGH OR FRONT
Tweeter (high)
WIDE L/R terminal posts connect to the front speak-
ers’ tweeter terminals. Woofer (low)
• Once you’ve completed the bi-amping connections
shown below and turned on the AV receiver, you must
set the “Speakers Type” setting to “Bi-Amp” to
enable bi-amping (➔ 41).
Important:
• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low)
terminals.
• Bi-amping can be used only with speakers that support bi-amping. Refer to your speaker manual. En
15
About AV Connections
Connected image with AV components
HDMI cable : Video & Audio Other cables : Video

: Audio
AV receiver AV receiver
Blu-ray Disc/ Blu-ray Disc/

TV, projector, etc. DVD player Game console TV, projector, etc. DVD player Game console
• Before making any AV connections, read the manuals supplied with your AV components.
• Don’t connect the power cord until you’ve completed and double-checked all AV connections. Right!
• Push plugs in all the way to make good connections (loose connections can cause noise or malfunc-
tions).
• To prevent interference, keep audio and video cables away from power cords and speaker cables.
Wrong!
AV Cables and Jacks
Signal Cable Jack Description

Video and HDMI HDMI
HDMI connections can carry digital video and audio.
Audio
Video Component video Y Component video separates the luminance (Y) and color
Green
difference signals (PB/CB, PR/CR), providing the best pic-
PB/CB Blue ture quality (some TV manufacturers label their compo-
PR/CR nent video sockets slightly differently).
Red
Composite video Composite video is commonly used on TVs, VCRs, and

V Yellow other video equipment.
Audio Optical digital OPTICAL Optical digital connections allow you to enjoy digital
audio sound such as PCM*, Dolby Digital or DTS. The audio
quality is the same as coaxial.
Coaxial digital Coaxial digital connections allow you to enjoy digital
audio Orange sound such as PCM*, Dolby Digital or DTS. The audio
quality is the same as optical.
Analog audio L White Analog audio connections (RCA) carry analog audio.
(RCA)
R Red
1/8" (3.5 mm) This cable carries analog audio.

Stereo mini plug
* Available sampling rate for PCM input signal is 32/44.1/48/88.2/96 kHz. Even 176.4/192 kHz is effective in case of the HDMI con-
nection.
Note
• The AV receiver does not support SCART plugs.
• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed.
Push plugs in all the way.
Caution
• To prevent shutter damage, hold the optical plug straight when inserting and removing.
En
16
Connecting Components with HDMI
VCR or DVD recorder/Digital Video Recorder
Game console
TV, projector, etc.
Personal
computer
Blu-ray Disc/DVD player
Camcorder
Satellite, cable, set-top box, etc.
Connect your components to the appropriate jacks. The default input assignments are shown below.
✔: Assignment can be changed (➔ 39).
Jack Signal Components Assignable

Input HDMI IN 1 Audio/Video Blu-ray Disc/DVD player ✔
HDMI IN 2 VCR or DVD recorder/Digital Video Recorder ✔
HDMI IN 3 Satellite, cable, set-top box, etc. ✔
HDMI IN 4 Game console ✔
HDMI IN 5 Personal computer ✔
AUX INPUT HDMI Camcorder
Output HDMI OUT TV, projector, etc.
Refer to “About HDMI” (➔ 72) and “Using an RIHD-compatible TV, Player, or Recorder” (➔ 73).
Tip
To listen to audio received by the HDMI IN jacks through your TV’s speakers:
• Set the “TV Control” setting to “On” (➔ 52) for an p-compatible TV.
• Set the “Audio TV Out” setting to “On” (➔ 51) when the TV is not compatible with p or the “TV Control” setting to “Off”.
• Set your Blu-ray Disc/DVD player’s HDMI audio output setting to PCM.
• To listen to TV audio through the AV receiver, see “Connecting External Components” (➔ 18).
Note
• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV
screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to
another input source, this may result in no sound from the AV receiver or the sound may be cut off.
• When the “Audio TV Out” setting is set to “On” (➔ 51) to hear from your TV’s speakers, by controlling the AV receiver’s volume,
the sound will be output from the AV receiver’s speakers, too. When the “TV Control” setting is set to “On” (➔ 52) to hear from
speakers of p-compatible TV, by controlling the AV receiver’s volume, the AV receiver’s speakers will produce sound while the
TV’s speakers are muted. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
■ Audio return channel (ARC) function

Audio return channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT of the
AV receiver. To use this function, you must select the TV/CD input selector.
• To use ARC function, you must select the TV/CD input selector, your TV must support ARC function and “HDMI
Control” is set to “On”(➔ 52).
En
17
Connecting External Components
The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to
the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.
Front Rear
A C B F D E
Connect your components to the appropriate jacks. The default input assignments are shown below.
✔: Assignment can be changed (➔ 40).
No. Jack Signal Components Assignable

A AUX INPUT LINE IN Analog audio Portable audio player
VIDEO Composite video Camcorder, etc
AUDIO L/R Analog audio
B COMPONENT IN 1 (BD/DVD) Component video Blu-ray Disc/DVD player ✔
VIDEO IN 2 (CBL/SAT) Satellite, cable, set-top box, etc. ✔
OUT TV, projector, etc.
C DIGITAL IN OPTICAL IN 1 (GAME) Digital audio Game console ✔
IN 2 (TV/CD) TV, CD player ✔
COAXIAL IN 1 (BD/DVD) Blu-ray Disc/DVD player ✔
IN 2 (CBL/SAT) Satellite, cable, set-top box, etc. ✔
D MONITOR OUT Composite video TV, projector, etc.
BD/DVD IN Analog audio and Blu-ray Disc/DVD player
VCR/DVR IN composite video VCR or DVD recorder/Digital
Video Recorder
CBL/SAT IN Satellite, cable, set-top box, etc.
GAME IN Game console
PC IN Analog audio Personal computer
TV/CD IN TV, CD player, Turntable*1,
Cassette tape deck, MD, CD-R
E UNIVERSAL PORT Analog audio/ Universal port optional dock
Video (UP-A1 etc.)
F PC IN Analog RGB Personal computer *2
En
18
Note
• When you connect to both AUX INPUT AUDIO jacks and AUX INPUT LINE IN jack at the same time, AUX INPUT LINE IN jack
will be given a higher priority.
• The AV receiver can output audio and video signals from the AUX INPUT jacks to the VCR/DVR OUT jacks.
*1 Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesn’t have it, you’ll need a commercially
available phono preamp.
If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer as
well as a phono preamp. See your turntable’s manual for details.
*2 When you connect your personal computer to PC IN and select PC input selector, video of the personal computer is output from
HDMI OUT. However, if you have assigned HDMI IN to the PC input selector, the AV receiver will output signals from HDMI IN
instead of signals from PC IN. To get the signals output from PC IN, select “- - - - -” for “PC” in the “HDMI Input” setting
(➔ 39).
• With connection D, you can listen and record audio from the external components while you are in Zone 2. You can lis-
ten and record audio from the external components in the main room; you can listen to the audio in Zone 2 as well.
• With connection C, you can enjoy Dolby Digital and DTS. (To record or listen in Zone 2 as well, use C and D.)
• With connection D, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to
connect the main stereo.
■ How to record the video
With the connections described above, you cannot record the video through the AV receiver. To make a connection for
video recording (➔ 31).
En
19
Connecting Onkyo u Components
Step 1: Note
Make sure that each Onkyo component is connected • Use only u cables for u connections. u cables are supplied
with an analog audio cable (connection D in the hookup with Onkyo players (DVD, CD, etc.).
examples) (➔ 18). • Some components have two u jacks. You can connect either
Step 2: one to the AV receiver. The other jack is for connecting addi-
tional u-capable components.
Make the u connection (see illustration below).
• Connect only Onkyo components to u jacks. Connecting other
Step 3: manufacturer’s components may cause a malfunction.
If you’re using an RI Dock, or cassette tape deck, • Some components may not support all u functions. Refer to
change the Input Display (➔ 25). the manuals supplied with your other Onkyo components.
• While Zone 2 is on, the System On/Auto Power On and Direct
With u (Remote Interactive), you can use the following Change u functions do not work.
special functions:
IN
■ System On/Auto Power On L
When you start playback on a component connected via R
TV/CD
u while the AV receiver is on Standby, the AV
receiver will automatically turn on and select that com- IN
ponent as the input source. L
REMOTE
■ Direct Change
R
CONTROL
BD/DVD
When playback is started on a component connected via

u, the AV receiver automatically selects that compo-
nent as the input source.
R L
■ Remote Control e.g., CD player

ANALOG
AUDIO OUT
You can use the AV receiver’s remote controller to con-

trol your other u-capable Onkyo components, point-
ing the remote controller at the AV receiver’s remote R
ANALOG
L
control sensor instead of the component. You must enter e.g., DVD player AUDIO OUT
the appropriate remote control code first (➔ 63).
Connecting Antenna
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use
the tuner.
Caution
North American and European, Australian and
Taiwan models Asian models • Be careful that you don’t injure yourself when
using thumbtacks.
Insert the plug fully Insert the plug fully

into the jack. into the jack.
Push. Insert wire. Release.
Assembling the AM loop antenna
Thumbtacks, etc.
Indoor FM antenna (supplied)
AM loop antenna (supplied)
Note
• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible
reception.
• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.
Tip
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.
En • If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM
antenna.
20
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your components. Use the following sections as a guide.
The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to
the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.
Video Connection Formats

Video component can be connected by using any one of the following video connection formats: composite video, com-
ponent video, or HDMI, the latter offering the best picture quality.
For optimal video performance, THX recommends that Video Signal Flow Chart
video signals pass through the system without upconver- Blu-ray Disc/DVD player, etc.
sion (e.g., component video input through to component
video output).
Composite Component HDMI
It is also recommended that you press VCR/DVR and
RETURN on the AV receiver at the same time. Select IN
“Skip” in the “VideoProcessor” setting by pressing
RETURN repeatedly on the display. To reset back to the AV receiver
original setting, press the same button at the same time.
Video input signals flow through the AV receiver as shown, MONITOR OUT
with composite video and component video sources all being
upconverted for the HDMI output.
The composite video and component video outputs pass TV, projector, etc.
through their respective input signals as they are.
When you connect audio component to an HDMI or COMPONENT input, you must assign that input to an input selector
(➔ 39).
■ Signal Selection
If signals are present at more than one input, the inputs will Signal Selection Example
be selected automatically in the following order of priority: Blu-ray Disc/DVD player, etc.
HDMI, component video, composite video.
However, for component video only, regardless of whether a
component video signal is actually present, if a component Composite Component HDMI
video input is assigned to the input selector, that component IN

video input will be selected. And if no component video
input is assigned to the input selector, this will be interpreted AV receiver
as no component video signal being present.
In the Signal Selection Example shown on the right, video MONITOR OUT
signals are present at both the HDMI and composite video
inputs, however, the HDMI signal is automatically selected
as the source and video is output by the HDMI outputs. TV, projector, etc.
Audio Connection Formats

Audio component can be connected by using any of the Audio Signal Flow Chart
following audio connection formats: analog, optical, coax- Blu-ray Disc/DVD player, etc.
ial, or HDMI.
When choosing a connection format, bear in mind that the
Analog Optical Coaxial HDMI
AV receiver does not convert digital input signals for ana-
log line outputs and vice versa. For example, audio signals IN
connected to an optical or coaxial digital input are not out- AV receiver *1 *1
*1
put by the analog VCR/DVR OUT.
OUT
Analog HDMI
If signals are present at more than one input, the inputs
will be selected automatically in the following order of pri- *1 *2
ority: HDMI, digital, analog. TV, projector, etc.
*1 Depends on the “Audio TV Out” setting (➔ 51).
*2 This setting is available, when “Audio Return Channel”
setting is set to “Auto” (➔ 52), you must select the TV/CD En
input selector and your TV must support ARC function.
21
Turning On/Off the AV Receiver
ON/STANDBY
STANDBY indicator
ON/STANDBY
RECEIVER
Front panel Remote controller
Turning On
Press ON/STANDBY on the front panel.
or
Press RECEIVER followed by ON/STANDBY on the remote controller.
The AV receiver comes on, the display lights, and the STANDBY indicator goes off.
Turning Off
Press ON/STANDBY on the front panel or the remote controller.
The AV receiver will enter Standby mode. To prevent any loud surprises when you turn on the AV receiver, always
turn down the volume before you turn it off.
En
22
Basic Operations
The on-screen menus appear only on a TV that is con- Displaying Source Information
nected to the HDMI OUT. If your TV is connected to
the MONITOR OUT V or the COMPONENT VIDEO You can display various information about the current
OUT, use the AV receiver’s display when changing input source as follows. (Components connected to the
settings. UNIVERSAL PORT jack are excluded.)
Press RECEIVER followed by DISPLAY repeat-

This manual describes the procedure using the edly to cycle through the available information.
remote controller unless otherwise specified.
Tip
Selecting the Language Used for the • Alternatively, you can use the AV receiver’s DISPLAY.
Onscreen Setup Menus The following information can typically be displayed.
You can determine the language used for the onscreen Input source &
setup menus. See “OSD Setup” (➔ 50). volume*1
Playing the Connected Component Signal format*2

or sampling fre-
■ Operating on the AV receiver quency
1 Use the input selector buttons to select the input

source.
Input & output
resolution
2 Start playback on the source component.

Input source &
See also:
listening mode*3
• “Controlling Other Components” (➔ 62)
• “Controlling iPod” (➔ 58) *1 When AM or FM radio is used, the band, preset number, and
• “Listening to the Radio” (➔ 28) frequency are displayed.
3 To adjust the volume, use the MASTER VOLUME
control.
*2 If the input signal is analog, no format information is dis-
played. If the input signal is PCM, the sampling frequency is
displayed. If the input signal is digital but not PCM, the signal
4 Select a listening mode and enjoy! format is displayed.
See also: Information is displayed for about three seconds, then the pre-
• “Using the Listening Modes” (➔ 32) viously displayed information reappears.
*3 The input source is displayed with the default name even
• “Audyssey” (➔ 45)
when you have entered a custom name in “Name Edit”
(➔ 47).
■ Operating with the remote controller
1 Press RECEIVER followed by INPUT SELEC-

TOR.
Setting the Display Brightness
2 Start playback on the source component. You can adjust the brightness of the AV receiver’s display.
See also:
Press RECEIVER followed by DIMMER repeat-
• “Controlling Other Components” (➔ 62)
edly to select: dim, dimmer, or normal brightness.
• “Controlling iPod” (➔ 58)
• “Listening to the Radio” (➔ 28)
Tip
3 To adjust the volume, use VOL q/w. • Alternatively, you can use the AV receiver’s DIMMER (North
4
American and Taiwan models).
Select a listening mode and enjoy!
See also:
• “Using the Listening Modes” (➔ 32)
En
23
Muting the AV Receiver Using the Home Menu
You can temporarily mute the output of the AV receiver. The Home menu provides you quick access to frequently
used menus without having to go through the long stan-
Press RECEIVER followed by MUTING. dard menu. This menu enables you to change settings and
The output is muted and the MUTING indicator view the current information.
flashes on the display.
1 Press RECEIVER followed by Home.
Tip The following information will be superimposed on
the TV screen.
• To unmute, press MUTING again or adjust the volume.
• The Mute function is cancelled when the AV receiver is set to BD/DVD
Standby.
Audio Bass
Video Treble 0dB
Info Subwoofer Level
Using the Sleep Timer Input Sel
Listening Mode
Center Level
Dynamic EQ
•
Dynamic Volume
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
Press RECEIVER followed by SLEEP repeatedly 2 Use q/w/e/r to make the desired selection.
to select the required sleep time. Àudio*1
The sleep time can be set from 90 to 10 minutes in You can change the following settings: “Bass”,
10 minute steps. “Treble”, “Subwoofer Level”, “Center
The SLEEP indicator lights on the display when the Level”, “Dynamic EQ”, “Dynamic Volume”,
sleep timer has been set. The specified sleep time “Late Night”, “Music Optimizer”, “Re-EQ”,
appears on the display for about five seconds, then “Re-EQ(THX)”, and “Audio Selector”.
the previous display reappears. See also:
• “Using the Audio Settings” (➔ 52)
Tip
`Video*2
• If you need to cancel the sleep timer, press SLEEP repeatedly
You can change the following settings: “Wide
until the SLEEP indicator goes off.
• To check the time remaining until the AV receiver sleeps, press
Mode” and “Picture Mode”. The remote con-
SLEEP. Note that if you press SLEEP while the sleep time is troller’s VIDEO acts as a shortcut for this
being displayed, you’ll shorten the sleep time by 10 minutes. menu.
See also:
Selecting Speaker Layout • “Picture Adjust” (➔ 48)
Ìnfo*3*4
You can prioritize which speakers you want to use. You can view the information of the following
items: “Audio”, “Video”, and “Tuner”.
Press RECEIVER followed by SP LAYOUT Ìnput*4*5
repeatedly. You can select the input source while viewing
`Speaker Layout:FH: the information as follows: the name of input
The sound from front high speakers is output selectors, input assignments, and radio infor-
by priority. mation, and ARC function setting.
`Speaker Layout:FW: Press ENTER to display the current input
The sound from front wide speakers is output source, followed by q/w to select the desired
by priority. input source. Pressing ENTER again switches
`Speaker Layout:SB: to the selected input source.
The sound from surround back speakers is out- `Listening Mode
put by priority. You can select the listening modes that are
grouped in the following categories: MOVIE/
Note TV, MUSIC, GAME, and THX.
• If the “Speakers Type” setting is set to “Bi-Amp” (➔ 41), or Use q/w to select the category and e/r to
Powered Zone 2 is being used (➔ 56), this setting cannot be select the listening mode. Press ENTER to
selected. switch to the selected listening mode.
• When the listening mode that doesn’t support front high, front
wide or surround back speakers is used, the setting cannot be
selected.
En
24
Note Using Headphones
*1 If Pure Audio (European, Australian and Asian) or Direct
listening mode is selected, “Dynamic EQ” and Connect a pair of stereo headphones with a stan-
“Dynamic Volume” cannot be selected. dard plug (1/4 inch or 6.3 mm) to the PHONES
*2 Only when you have selected “Custom” in the “Picture jack.
Mode” (➔ 48), pressing ENTER allows you to adjust the fol-
lowing items via the Home menu; “Brightness”, “Contrast”,
“Hue”, and “Saturation”. Press RETURN to return to the Note
original Home menu. • Always turn down the volume before connecting your head-
*3 Depending on the input source and listening mode, not all phones.
channels shown here output the sound. • While the headphones plug is inserted in the PHONES jack, the
*4 When you have entered a custom name in “Name Edit” speakers are turned off. (The Powered Zone 2 speakers are not
(➔ 47), the input source is displayed with that name. But turned off.)
even if not, the component name may be displayed if the AV • When you connect a pair of headphones, the listening mode is
receiver receives it via HDMI connection (➔ 17). set to Stereo, unless it’s already set to Stereo, Mono, Direct, or
*5 For the PORT input selector, the name of Universal Port Pure Audio (European, Australian and Asian models).
Option Dock will be displayed. • Only the Stereo, Direct, Pure Audio (European, Australian and
Asian models), and Mono listening modes can be used with
headphones.
Changing the Input Display
When you connect an u-capable Onkyo component, you Audyssey 2EQ® Room Correction and
must configure the input display so that u can work Speaker Setup
properly.
This setting can be done only from the front panel. With the supplied calibrated microphone, Audyssey 2EQ
automatically determines the number of speakers con-
1 Press TV/CD, GAME or VCR/DVR so that “TV/
CD”, “GAME” or “VCR/DVR” appears on the
nected, their size for purposes of bass management, opti-
mum crossover frequencies to the subwoofer (if present),
display. and distances from the primary listening position.
Audyssey 2EQ then removes the distortion caused by
room acoustics by capturing room acoustical problems
over the listening area in both the frequency and time
domain. The result is clear, well-balanced sound for every-
one. Enabling Audyssey 2EQ allows you to also use
Audyssey Dynamic EQ™, which maintains the proper
octave-to-octave balance at any volume level (➔ 45).
Before using this function, connect and position all of
2 Press and hold down TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
your speakers.
If “Dynamic EQ” is set to “On” (➔ 45), the “Equalizer”
Repeat this step to select “MD”, “CDR”, “DOCK” setting will be set to “Audyssey” (➔ 42). On the other
or “TAPE”. hand, if it is set to “Off”, the “Dynamic Volume” setting
For the TV/CD input selector, the input display will be set to “Off” (➔ 46).
changes in this order: It takes about 15 minutes to complete Audyssey 2EQ
TV/CD → MD → CDR Room Correction and Speaker Setup for three positions.
→
TAPE →
DOCK
→ Total measurement time varies depending on the number
of speakers.
For the GAME input selector, the setting changes in
this order:
GAME ↔ DOCK
For the VCR/DVR input selector, the setting

changes in this order:
VCR/DVR ↔ DOCK
Note
• DOCK can be selected for the TV/CD, GAME or VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (➔ 62).
En
25
Using Audyssey 2EQ® 1 Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV receiver
To create a listening environment in your home theater is connected.
that all listeners will enjoy, Audyssey 2EQ takes measure-
ments at up to three positions within the listening area. 2 Set the speaker setup microphone at the Main Lis-
tening Position 1, and connect it to the SETUP
Position the microphone at ear height of a seated listener
with the microphone tip pointed directly at the ceiling MIC jack.
using a tripod. Do not hold the microphone in your hand SETUP MIC jack
during measurements as this will produce inaccurate
results. Speaker setup
microphone
a First measurement position
Also referred to as the Main Listening Position this
refers to the most central position where one would
normally sit within the listening environment. 2EQ
uses the measurements from this position to calculate
speaker distance, level, polarity, and the optimum The speaker setting menu appears.
crossover value for the subwoofer. Note
b Second measurement position • The on-screen setup menus appear only on a TV that is
The right side of the listening area. connected to the HDMI OUT. If your TV is connected to
c Third measurement position the MONITOR OUT V or the COMPONENT VIDEO
OUT, use the AV receiver’s display when changing set-
The left side of the listening area.
tings.
The distances from position a to b and a to c must be
at least 1 meter. 3 When you’ve finished making the settings, press
ENTER.
2EQ: Auto Setup

TV
Speakers Type Normal
Speaker Terminal Assign

Front High/Front Wide/Zone2 Front High
SurrBack/Front High/Front Wide Surr Back
If your front speakers are bi-amped, you must select

“Bi-Amp” in the “Speakers Type” setting (➔ 41).
For hookup information, see “Bi-amping the Front
Speakers” (➔ 15).
: Listening area a to c: Listening position
4 Press ENTER.
Note Audyssey 2EQ Room Correction and Speaker Setup
• Make the room as quiet as possible. Background noise and Radio starts.
Frequency Interference (RFI) can disrupt the room measure- Test tones are played through each speaker as
ments. Close windows, televisions, radios, air conditioners, flu- Audyssey 2EQ Room Correction and Speaker Setup
orescent lights, home appliances, light dimmers, or other runs. This process takes a few minutes. Please
devices. Turn off the cell phone (even if it is not in use) or place refrain from talking during measurements and do
it away from all audio electronics.
not stand between speakers and the microphone.
• The microphone picks up test tones which played through each
speaker as Audyssey 2EQ Room Correction and Speaker Setup Do not disconnect the speaker setup microphone
run. during Audyssey 2EQ Room Correction and
• Audyssey 2EQ Room Correction and Speaker Setup cannot be Speaker Setup, unless you want to cancel the setup.
5
performed while a pair of headphones is connected. Place the setup microphone at the next position,
and then press ENTER.
Audyssey 2EQ performs more measurements. This
takes a few minutes.
6 When prompted, repeat step 5.
En
26
7 Use q/w to select an option, and then press The options are:
` Retry:
ENTER.
Try again.
2EQ: Auto Setup ` Cancel:
- - Review Speaker Configuration - - Cancel Audyssey 2EQ Room Correction and
Subwoofer Yes
Front Full Band
Speaker Setup.
TV
Center 40Hz
Surround 100Hz
• Ambient noise is too high.
Front Wide None
Front High 100Hz
The background noise is too loud. Remove the source of
Surr Back
Surr Back Ch
120Hz
2ch
the noise and try again.
• Speaker Matching Error!
Save
Cancel The number of speakers detected was different from
that of the first measurement. Check the speaker con-
The options are: nection.
` Save: • Writing Error!
Save the calculated settings and exit
This message appears if saving fails. Try saving again.
Audyssey 2EQ® Room Correction and Speaker
If this message appears after 2 or 3 attempts, contact
Setup.
your Onkyo dealer.
` Cancel:
• Speaker Detect Error
Cancel Audyssey 2EQ Room Correction and
This message appears if a speaker is not detected. “No”
Speaker Setup.
means that no speaker was detected.
Note
Tip
• You can view the calculated settings for the speaker con-
figuration, speaker distances, and speaker levels by using • See “Speaker Configuration” for appropriate settings (➔ 13).
e/r.
Changing the Speaker Settings Manually
8 Disconnect the speaker setup microphone.
You can manually make changes to the settings found dur-
ing Audyssey 2EQ Room Correction and Speaker Setup.
Note See also:
• When Audyssey 2EQ Room Correction and Speaker Setup is • “Speaker Configuration” (➔ 41)
complete, the “Equalizer” will be set to “Audyssey” (➔ 42). • “Speaker Distance” (➔ 42)
The Audyssey indicator will light (➔ 9).
• “Level Calibration” (➔ 42)
• You can cancel Audyssey 2EQ Room Correction and Speaker
Setup at any point in this procedure simply by disconnecting the • “Equalizer Settings” (➔ 42)
setup microphone. Note
• Do not connect or disconnect any speakers during
• Please note that THX recommends any THX main speakers be
Audyssey 2EQ Room Correction and Speaker Setup.
set to “80Hz(THX)”. If you set up your speakers using
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey 2EQ Room Correction and Speaker Setup starts.
Audyssey 2EQ Room Correction and Speaker Setup, please
• Changes to the room after Audyssey 2EQ Room Correction and make sure manually that any THX speakers are set to 80 Hz
Speaker Setup requires you run Audyssey 2EQ Room Correc- (THX) crossover (➔ 40).
tion and Speaker Setup again, as room EQ characteristics may • Sometimes due to the electrical complexities of subwoofers and
have changed. the interaction with the room, THX recommends setting the level
and the distance of the subwoofer manually.
• Sometimes due to interaction with the room, you may notice
Error Messages
irregular results when setting the level and/or distance of the
While Audyssey 2EQ Room Correction and Speaker main speakers. If this happens, THX recommends setting them
Setup is in progress, one of the error messages below may manually.
appear.
Using a Powered Subwoofer
2EQ: Auto Setup
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
Ambient noise is too high.
detected by Audyssey 2EQ Room Correction and Speaker
Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the subwoofer’s
Retry volume to the half-way point, set it to its highest crossover
Cancel
frequency, and then try running Audyssey 2EQ Room
Correction and Speaker Setup again. Note that if the vol-
Error message
ume is set too high and the sound distorts, detection issues
may occur, so use an appropriate volume level. If the sub-
woofer has a low-pass filter switch, set it to Off or Direct.
Refer to your subwoofer’s instruction manual for details. En
27
Listening to the Radio
■ Manual tuning mode
This section describes the procedure using the but-
1
tons on the front panel unless otherwise specified.
Press TUNING MODE so that the AUTO indicator
goes off on the display.
2
Using the Tuner Press and hold TUNING q/w.
With the built-in tuner you can enjoy AM and FM radio The frequency stops changing when you release the
stations. You can store your favorite stations as presets for button.
quick selection. Press the buttons repeatedly to change the frequency
This model changes FM/AM frequency in 200/10kHz (or one step at a time.
50/9kHz) steps.
In manual tuning mode, FM stations will be in mono.
Listening to the Radio Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
Press TUNER to select either “AM” or “FM”. impossible to get good reception. In this case, switch to
In this example, FM has been selected. manual tuning mode and listen to the station in mono.
Each time you press TUNER, the radio band
■ Tuning into stations by frequency
changes between AM and FM.
You can tune into AM and FM stations directly by enter-
Band Frequency ing the appropriate frequency.
1 On the remote controller, press TUNER repeat-

edly to select “AM” or “FM”, followed by D.TUN.
(Actual display depends on the country.)
Tuning into Radio Stations

(Actual display depends on the country.)
■ Auto tuning mode
2 Within 8 seconds, use the number buttons to enter
1 Press TUNING MODE so that the AUTO indicator
lights on the display.
the frequency of the radio station.
For example, to tune to 87.50 (FM), press 8, 7, 5, 0.
2
If you have entered the wrong number, you can retry
Press TUNING q/w.
after 8 seconds.
Searching stops when a station is found.
When tuned into a station, the TUNED indicator lights.

When tuned into a stereo FM station, the FM STEREO
indicator lights on the display, as shown.
FM STEREO
AUTO
TUNED
En
28
Presetting FM/AM Stations Using RDS (excluding North American
models)
You can store a combination of up to 40 of your favorite
FM/AM radio stations as presets.
RDS works only in areas where RDS broadcasts are
1 Tune into the FM/AM station that you want to
store as a preset.
available.
See the previous section. When tuned into an RDS station, the RDS indicator lights.
2 Press MEMORY. What is RDS?

The preset number flashes.
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed by
the European Broadcasting Union (EBU) and is available
in most European countries. Many FM stations use it these
3 While the preset number is flashing (about 8 sec- days. In addition to displaying text information, RDS can
onds), use PRESET e/r to select a preset from 1 also help you find radio stations by type (e.g., news, sport,
through 40. rock, etc.).
4 Press MEMORY again to store the station or chan-

nel.
The AV receiver supports four types of RDS information:
■ PS (Program Service)
The station or channel is stored and the preset num- When tuned to an RDS station that’s broadcasting PS
ber stops flashing. information, the station’s name will be displayed. Press-
Repeat this procedure for all of your favorite FM/ ing DISPLAY will display the frequency for 3 seconds.
AM radio stations.
■ RT (Radio Text)
When tuned to an RDS station that’s broadcasting text
Note
information, the text will be shown on the display as
• You can name your radio presets for easy identification (➔ 47). described in the next section.
Its name is displayed instead of the band and frequency.
■ PTY (Program Type)
Selecting Presets This allows you to search for RDS radio stations by type
(➔ 30).
To select a preset, use PRESET e/r on the AV ■ TP (Traffic Program)
receiver, or the remote controller’s CH +/–. This allows you to search for RDS radio stations that
broadcast traffic information (➔ 30).
Tip Note
• You can also use the remote controller’s number buttons to select • In some cases, the text characters displayed on the AV receiver
a preset directly. may not be identical to those broadcast by the radio station. Also,
unexpected characters may be displayed when unsupported
Deleting Presets characters are received. This is not a malfunction.
• If the signal from an RDS station is weak, RDS data may be
displayed intermittently or not at all.
1 Select the preset that you want to delete.
See the previous section. When tuned to an RDS station that’s broadcasting text
2 While holding down MEMORY, press TUNING
MODE.
information, the text can be displayed.
The preset is deleted and its number disappears from Displaying Radio Text (RT)
the display.
Press RT/PTY/TP once.
The RT information scrolls across the display.
Note
• The message “Waiting” may appear while the AV receiver waits
for the RT information.
• If the message “No Text Data” appears on the display, no RT
information is available.
En
29
Finding Stations by Type (PTY) ■ RDS program types (PTY)
You can search for radio stations by type. Type Display

None None
1 Press RT/PTY/TP twice. News reports News
The current program type appears on the display. Current affairs Affairs
2 Use PRESET e/r to select the type of program Information

Sport
Info
Sport
you want.
See the table shown later in this chapter. Education Educate
3
Drama Drama
To start the search, press ENTER.
Culture Culture
The AV receiver searches until it finds a station of
the type you specified, at which point it stops briefly Science and technology Science
before continuing with the search. Varied Varied
4
Pop music Pop M
When a station you want to listen to is found, press
Rock music Rock M
ENTER.
Middle of the road music Easy M
If no stations are found, the message “Not Found”
appears. Light classics Light M
Serious classics Classics
Listening to Traffic News (TP) Other music Other M
Weather Weather
You can search for stations that broadcast traffic news. Finance Finance
Children’s programmes Children
1 Press RT/PTY/TP three times. Social affairs Social
If the current radio station is broadcasting TP (Traf- Religion Religion
fic Program), “[TP]” will appear on the display, and
Phone in Phone In
traffic news will be heard as and when it’s broadcast.
Travel Travel
If “TP” without square brackets appears, this means
Leisure Leisure
that the station is not broadcasting TP.
Jazz music Jazz
2 To locate a station that is broadcasting TP, press
ENTER.
Country music Country
National music Nation M
The AV receiver searches until it finds a station that’s
Oldies music Oldies
broadcasting TP.
Folk music Folk M
If no stations are found, the message “Not Found”
Documentary Document
appears.
Alarm test TEST
Alarm Alarm!
En
30
Recording
This section explains how to record the selected input source to a component with recording capability, and how to record
audio and video from different sources.
Connecting a Recording Component

3 On the source component, start playback.
If you select another input source during recording,
that input source will be recorded.
Recording Separate AV Sources

Here you can record audio and video from completely
separate sources, allowing you to overdub audio onto your
video recordings. This function takes advantage of the fact
that when an audio-only input source (TV/CD) is selected,
L R the video input source remains unchanged.
AUDIO
IN
VIDEO
IN In the following example, audio from the CD player con-
nected to the TV/CD IN and video from the camcorder
connected to the AUX INPUT VIDEO jack are recorded
by the VCR connected to the VCR/DVR OUT jacks.
VCR, Cassette, CDR,
DVD recorder MD, etc. Camcorder
Note
• The AV receiver must be turned on for recording. Recording is
not possible while it’s in Standby mode.
• If you want to record directly from your TV or playback VCR to
the recording VCR without going through the AV receiver, con-
nect the TV/VCR’s audio and video outputs directly to the
recording VCR’s audio and video inputs. See the manuals sup-
plied with your TV and VCR for details.
• Video signals connected to composite video inputs can be
recorded only via composite video outputs. If your TV/VCR is
connected to a composite video input, the recording VCR must
be connected to a composite video output.
• The surround sound and DSP listening modes cannot be
recorded.
• Copy-protected Blu-ray Disc/DVDs cannot be recorded.
• Sources connected to a digital input cannot be recorded. Only
analog inputs can be recorded.
• DTS signals will be recorded as noise, so don’t attempt analog
recording of DTS CDs or LDs.
• While the listening mode is set to Pure Audio, no image is pro-
CD player VCR
vided because the power is turned off for the video circuit. If you
want to make recordings, select other listening mode. (Euro-
pean, Australian and Asian models) : Video signal
: Audio signal
AV Recording
Audio sources can be recorded to a recorder (e.g., cassette 1 Prepare the camcorder and CD player for play-
back.
deck, CDR, MD) connected to the VCR/DVR OUT jacks.
Video sources can be recorded to a video recorder (e.g., 2 Prepare the VCR for recording.
VCR, DVD recorder) connected to the VCR/DVR OUT
jack. 3 Press AUX input selector.
1 Use the input selector buttons to select the source 4 Press TV/CD input selector.
that you want to record. This selects the CD player as the audio source, but
You can watch the source while recording. The AV leaves the camcorder as the video source.
receiver’s MASTER VOLUME control has no effect
on recording.
5 Start recording on the VCR and start playback on
the camcorder and CD player.
2 On your recorder, start recording. The video from the camcorder and the audio from
the CD player are recorded by the VCR.
En
31
Using the Listening Modes
Selecting Listening Modes
See “About Listening Modes” for detailed information about the listening modes (➔ 33).
Listening Mode Buttons
(North American and Taiwan models)

Press RECEIVER first.
MOVIE/TV, MUSIC, GAME
(European, Australian and Asian models)
MUSIC GAME
MOVIE/TV THX
PURE AUDIO MOVIE/TV, MUSIC, GAME
MOVIE/TV button PURE AUDIO button and indicator

This button selects the listening modes intended for use (European, Australian and Asian models)
with movies and TV. This button selects the Pure Audio listening mode.
MUSIC button When this mode is selected, the AV receiver’s display
This button selects the listening modes intended for use and video circuitry are turned off. The indicator lights
with music. when this mode is selected. Pressing this button again
will select the previous listening mode.
GAME button
This button selects the listening modes intended for use
with video games.
THX button
This button selects the THX listening modes.
• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV
receiver with a digital audio connection (coaxial, optical, or HDMI).
• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source
Information” (➔ 23).
• While a pair of headphones is connected, you can select the following listening modes: Pure Audio (European, Australian and
Asian models), Mono, Direct, and Stereo.
• The listening modes cannot be used while you are listening to sound through your TV speakers coming from components
connected to the AV receiver (“TV Sp On” appears on the front panel).
En
32
About Listening Modes
The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidel-
ity and stunning surround sound.
Explanatory Notes
e
g a f
b
SP LAYOUT
d c
a Front speakers
LISTENING MODE b Center speaker
c Surround speakers
f Front wide speakers
g Subwoofers
■ Input Source
The following audio formats are supported by the listening mode.
A This is mono (monophonic) sound.

S This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two
speakers.
D This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth sub-
woofer channel (called the point-one channel).
F This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two
additional speakers that provide greater sound envelopment and more accurate positioning of sounds.
G This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth
channel from existing DTS 5.1 encoded material.
H This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel
sources.
■ Speaker Layout
The illustration shows which speakers are activated in each channel. See “Speaker Configuration” for the speaker setup
(➔ 41).
Z X C N
Press RECEIVER followed by SP LAYOUT repeatedly to

select the speakers you want to use; front high, front
wide, or surround back.
En
33
Listening Modes
Listening Mode Description Input Speaker

Source Layout
Pure Audio*1 In this mode, the display and video circuitry are turned off, minimizing pos- A ZXC
sible noise sources for the ultimate in high-fidelity audio reproduction. (As S N* 2
Pu r e Aud i o the video circuitry is turned off, only video signals input through HDMI IN D
can be output from HDMI OUT.)
F
Direct In this mode, audio from the input source is output without surround-sound G
processing. The “Sp Config” (presence of speakers), “Sp Distance” and H
D i r ec t “A/V Sync” settings are enabled, but much of the processing set via HOME
is disabled. See “Advanced Setup” for more details (➔ 38).
Stereo Sound is output by the front left and right speakers and subwoofer. A ZXC
S N
S t e r eo
D
Mono Use this mode when watching an old movie with a mono soundtrack, or use F
it with the foreign language soundtracks recorded in the left and right chan-
Mo n o G
nels of some movies. It can also be used with DVDs or other sources contain-
H
ing multiplexed audio, such as karaoke DVDs.
Multichannel This mode is for use with PCM multichannel sources. D XCN
Mu l t i c h
Dolby Pro Logic IIx*3 Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel play- S XCN
Dolby Pro Logic II back. It provides a very natural and seamless surround-sound experience that
fully envelops the listener. As well as music and movies, video games can
PL Mo v i e also benefit from the dramatic spatial effects and vivid imaging. If you’re not
using any surround back speakers, Dolby Pro Logic II will be used instead
PL Mu s i c of Dolby Pro Logic IIx.
• Dolby PLIIx Movie
PL Game Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g.,
TV, DVD, VHS).
P L x Mo v i e • Dolby PLIIx Music
Use this mode with any stereo or Dolby Surround (Pro Logic) music source
P L x Mu s i c (e.g., CD, radio, cassette, TV, VHS, DVD).
• Dolby PLIIx Game
Use this mode with video games, especially those that bear the Dolby Pro
P L x Game
Logic II logo.
• Dolby PLIIx Movie and Dolby PLIIx Music D N
These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel
sources for 7.1-channel playback.
Dolby Pro Logic IIz Dolby Pro Logic IIz Height is designed to more effectively use existing S N* 4
Height program material when height channel speaker outputs are present. Dolby D
Pro Logic IIz Height can be used to upmix a variety of sources from movies F
PL z He i g h t and music, but are particularly well-suited to upmix game content.
Dolby EX These modes expand 5.1-channel sources for 6.1/7.1-channel playback. D N* 5
They’re especially suited to Dolby EX soundtracks that include a matrix- H
Do l b y EX encoded surround back channel. The additional channel adds an extra dimen-
sion and provides an enveloping surround sound experience, perfect for
Do l b y D EX rotating and fly-by sound effects.
Dolby Digital In this mode, audio from the input source is output without surround-sound D XCN
processing. “Sp Config” (presence of speakers), “Crossover”, “Sp Dis-
Do l b y D tance”, “A/V Sync” and much of the processing set via HOME are enabled.
Dolby Digital Plus*6 See “Advanced Setup” for more details (➔ 38). D XCN
Do l b y D+ F XCN*2
Dolby TrueHD D XCN
T r u e HD F XCN*2
DTS D XCN
DTS
En
34
Source Layout
DTS-HD High (Continued from the previous page.) D XCN
Resolution Audio
F XCN*2
D T S – HD HR
DTS-HD Master D XCN
Audio
F XCN*2
D T S – HD MS T R
DTS Express S XCN
D
DTS Exp r ess
DSD*7 D XCN
DSD
DTS 96/24*8 This mode is for use with DTS 96/24 sources. This is high-resolution DTS D XCN
with a 96 kHz sampling rate and 24-bit resolution, providing superior fidel-
DTS 96 / 24 ity. Use it with DVDs that bear the DTS 96/24 logo.
DTS-ES Discrete*9 This mode is for use with DTS-ES Discrete soundtracks, which use a dis- G N* 5
crete surround back channel for true 6.1/7.1-channel playback. The seven
ES D i s c r e t e totally separate audio channels provide better spatial imaging and 360-
degree sound localization, perfect for sounds that pan across the surround
channels. Use it with DVDs that bear the DTS-ES logo, especially those with
a DTS-ES Discrete soundtrack.
DTS-ES Matrix*9 This mode is for use with DTS-ES Matrix soundtracks, which use a matrix- G N* 5
encoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that
ES Ma t r i x bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.
DTS Neo:6 This mode expands any 2-channel source for up to 7.1-channel playback. It S XCN*5
uses seven full-bandwidth channels of matrix decoding for matrix-encoded
Ne o : 6 material, providing a very natural and seamless surround sound experience
that fully envelops the listener.
N e o : 6 C i n e m a • Neo:6 Cinema
Use this mode with any stereo movie (e.g., TV, DVD, VHS).
N e o : 6 M u s i c • Neo:6 Music
Use this mode with any stereo music source (e.g., CD, radio, cassette, TV,
VHS, DVD).
This mode uses Neo:6 to expand 5.1-channel sources for 6.1/7.1-channel D N* 5
playback.
Audyssey DSX*10 Audyssey DSX™ is a scalable system that adds new speakers to improve sur- D N
round impression. Starting with a 5.1 system Audyssey DSX first adds Wide F
A u d y s s e y DSX channels for the biggest impact on envelopment. Research in human hearing G
has proven that information from the Wide channels is much more critical in
PL Mo v DSX the presentation of a realistic soundstage than then Back Surround channels
found in traditional 7.1 systems. Audyssey DSX then creates a pair of Height
PL Mu s DSX channels to reproduce the next most important acoustical and perceptual
cues. In addition to these new Wide and Height channels, Audyssey DSX
PL Gam DSX applies Surround Envelopment Processing to enhance the blend between the
front and surround channels.
*10
Ne o : 6 C D S X The combination of Dolby Pro Logic II and Audyssey DSX modes can S N
be used.
Ne o : 6 M D S X The combination of Neo:6 Cinema/Music and Audyssey DSX*10 modes S N
can be used.
En
35
Source Layout
THX Founded by George Lucas, THX develops stringent standards that ensure D CN
movies are reproduced in movie theaters and home theaters just as the direc- F
THX C i n ema tor intended. THX Modes carefully optimize the tonal and spatial character- G
istics of the soundtrack for reproduction in the home-theater environment.
THX Mu s i c They can be used with 2-channel matrixed and multichannel sources. Sur-
round back speaker output depends on the source material and the selected
THX Game s listening mode.
• THX Cinema
THX S2 C i n THX Cinema mode corrects theatrical soundtracks for playback in a home
theater environment. In this mode, THX Loudness Plus is configured for
cinema levels and Re-EQ, Timbre Matching, and Adaptive Decorrelation
THX S 2 Mu s
are active.
• THX Music
THX S 2 Gam
THX Music mode is tailored for listening to music, which is typically mas-
tered at significantly higher levels than movies. In this mode, THX Loud-
THX Su r r EX ness Plus is configured for music playback and only Timbre Matching is
active.
• THX Games
THX Games mode is meant for spatially accurate playback of game audio,
which is often mixed similarly to movies but in a smaller environment. THX
Loudness Plus is configured for game audio levels, with Timbre Matching
active.
The combination of Dolby Pro Logic II/IIx*3 and THX Cinema/Music/ S CN
Games modes can be used. D
H
The combination of Dolby Pro Logic IIz Height*4 and THX Cinema/ S N
Music/Games modes can be used. D
F
G
H
The combination of DTS Neo:6 and THX Cinema/Music/Games modes S CN
can be used. D
F
H
• THX Select2 Cinema D N
This mode expands 5.1-channel sources for 7.1- channel playback. It does F
this by analyzing the composition of the surround source, optimizing the
ambient and directional sounds to produce the surround back channel out-
put.
• THX Select2 Music
This mode is designed for use with music. It expands 5.1-channel sources
for 7.1-channel playback.
• THX Select2 Games
This mode is designed for use with video games. It can expand 5.1-channel
sources for 6.1/7.1-channel playback.
• THX Surround EX
This mode expands 5.1-channel sources for 6.1/7.1- channel playback. It’s
especially suited to Dolby Digital EX sources. THX Surround EX, also
known as Dolby Digital Surround EX, is a joint development between
Dolby Laboratories and THX Ltd.
En
36
Onkyo-Original DSP Listening Modes

Source Layout
Orchestra Suitable for classical or operatic music, this mode emphasizes the surround A CN*11
channels in order to widen the stereo image, and simulates the natural rever- S
Or ches t r a beration of a large hall. D
Unplugged Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the G
front stereo image, giving the impression of being right in front of the stage. H
Un p l u g g e d
Studio-Mix Suitable for rock or pop music, listening to music in this mode creates a
lively sound field with a powerful acoustic image, like being at a club or rock
S t u d i o –M i x concert.
TV Logic This mode adds realistic acoustics to TV shows produced in a TV studio,
surround effects to the entire sound, and clarity to voices.
TV Log i c
Game-RPG Use this mode when playing role playing game discs.
G ame – RPG
Game-Action Use this mode when playing action game discs.
Game – A c t i o n
Game-Rock Use this mode when playing rock game discs.
Game –Ro c k
Game-Sports Use this mode when playing sports game discs.
Game – S p o r t s
All Ch Stereo Ideal for background music, this mode fills the entire listening area with ste- A XCN*11
reo sound from the front, surround, and surround back speakers. S
A l l Ch S t
D
Full Mono In this mode, all speakers output the same sound in mono, so the sound you F
hear is the same regardless of where you are within the listening room.
Fu l l Mo n o G
H
T-D (Theater- With this mode you can enjoy a virtual surround sound even with only two or ZXC
Dimensional) three speakers. This works by controlling how sounds reach the listener’s left N
and right ears. Good results may not be possible if there’s too much reverb,
T–D so we recommend that you use this mode in an environment with little or no
natural reverb.
Note
*1 (North American and Taiwan models) This listening mode is not available.
*2 When the input source contains the encoded front high or front wide channel, the corresponding speakers output the sound.
*3 If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.
*4 Surround back and front wide speakers are not supported.
*5 Front high and front wide speakers are not supported.
*6 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.
*7 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better
sound according to the player. In that case, set the output setting on the player side to PCM.
*8 Depending on the input source, DTS is used.
*9 If there are no surround back speakers, DTS is used.
*10 • This listening mode can be selected only when all the following conditions are satisfied:
a.Center speaker is connected.
b.Either of front high or front wide speakers is connected.
• Output can be switched between front high or front wide speakers by pressing SP LAYOUT [depending on the “Speaker Config-
uration” setting (➔ 41)].
*11 Output can be switched between front high, front wide or surround back speakers by pressing SP LAYOUT [depending on the
“Speaker Configuration” setting (➔ 41)].
• The listening modes cannot be selected with some source formats.
En
37
Advanced Setup
On-screen Setup Menus Common Procedures in Setup Menu
The on-screen setup menus appear only on a TV that Remote indicator

is connected to the HDMI OUT. If your TV is con-
nected to the composite video MONITOR OUT or the
COMPONENT VIDEO OUT, use the AV receiver’s
display when changing settings. RECEIVER
This manual describes the procedure using the

ENTER
remote controller unless otherwise specified. q/w/e/r
SETUP RETURN
MENU
a 1. Input/Output Assign
b 2. Speaker Setup The on-screen setup menus appear on the connected TV
c 3. Audio Adjust
and provide a convenient way to change the AV receiver’s
d 4. Source Setup
5. Listening Mode Preset various settings. Settings are organized into nine catego-
e
f 6. Miscellaneous ries on the main menu.
g 7. Hardware Setup Carry out the settings by using the on-screen display.
h 8. Remote Controller Setup
i 9. Lock Setup 1 Press RECEIVER followed by SETUP.
The following menu appears.
a Input/Output Assign f Miscellaneous (➔ 50)
(➔ 39) MENU
6. Miscellaneous
1. Input/Output Assign
1. Input/Output Assign 1. Volume Setup 2. Speaker Setup
2. OSD Setup 3. Audio Adjust
1. Monitor Out 4. Source Setup
2. HDMI Input 5. Listening Mode Preset
3. Component Video Input 6. Miscellaneous
4. Digital Audio Input 7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
b Speaker Setup (➔ 40) g Hardware Setup
(➔ 50)
2. Speaker Setup Tip
1. Speaker Settings 7. Hardware Setup • If the main menu doesn’t appear, make sure the appropri-
2. Speaker Configuration
3. Speaker Distance 1. Remote ID ate external input is selected on your TV.
4. Level Calibration 2. Tuner
2
5. Equalizer Settings 3. HDMI
6. THX Audio Setup Use q/w to select a menu, and then press ENTER.
c Audio Adjust (➔ 44) h Remote Controller

Setup (➔ 62)
3 Use q/w to select target and then press ENTER.
1.
3. Audio Adjust
Multiplex/Mono 8. Remote Controller Setup
4 Use q/w to select option and e/r to change the
2. Dolby setting.
3. DTS 1. Remote Mode Setup
4.
5.
Audyssey DSX
Theater-Dimensional
Press SETUP to close the menu.
6. LFE Level Press RETURN to return to the main menu.
d Source Setup (➔ 45) i Lock Setup (➔ 52)

Note
4. Source Setup 9. Lock Setup • This procedure can also be performed on the AV receiver by
1. Audyssey Lock using SETUP, arrow buttons, and ENTER.
2. IntelliVolume
3. A/V Sync • During Audyssey 2EQ® Room Correction and Speaker Setup,
4. Name Edit
5. Picture Adjust messages, etc., that are displayed on the TV screen will appear
in the Display.
e Listening Mode Preset
(➔ 49)
5. Listening Mode Preset

1. BD/DVD
2. VCR/DVR
3. CBL/SAT
4. GAME
5. PC
6. AUX
7. TUNER
En 8. TV/CD
9. PORT
38
Explanatory Notes Composite video,
component video HDMI
a Main Menu Speaker Setup IN
b Subwoofer
c Yes:
Select if a subwoofer is connected. OUT
Composite video, HDMI
No: component video
Select if no subwoofer is connected. Here are the default assignments.
a Menu selection
b Setting target Input selector Default assignment
c Setting options (default setting underlined) BD/DVD HDMI1
VCR/DVR HDMI2
CBL/SAT HDMI3
Input/Output Assign
GAME HDMI4
PC HDMI5*1
Main Menu Input/Output Assign
AUX FRONT (Fixed)
TUNER - - - - - (Fixed)
Monitor Out
TV/CD -----
You can specify the output resolution for the HDMI OUT PORT -----
and COMPONENT VIDEO MONITOR OUT and have
the AV receiver upconvert the picture resolution as neces- ■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,
sary to match the resolution supported by your TV. TV/CD, PORT
` HDMI1, HDMI2, HDMI3, HDMI4, HDMI5:
■ Resolution Select a corresponding HDMI input that the video
`Through: component has been connected.
Select this to pass video through the AV receiver at ` - - - - -:
the same resolution and with no conversion. Select this to output composite video and component
Àuto: video sources from the HDMI OUT. The video sig-
Select this to have the AV receiver automatically nal from HDMI output is configured in “Component
convert video at resolutions not supported by your Video Input” (➔ 40).
TV. *1 If you connect your personal computer to PC IN, you must
`480p (480p/576p): assign “- - - - -” to the “PC” input selector.
Select this for 480p or 576p output and video con- • “AUX” is used only for input from the front panel.
version as necessary. • Each HDMI input cannot be assigned to two input selec-
`720p: tors or more. When HDMI1 - HDMI5 have already
Select this for 720p output and video conversion as been assigned, you must set first any unused input selec-
necessary. tors to “- - - - -” or you will be unable to assign HDMI1
`1080i: - HDMI5 to input selector.
Select this for 1080i output and video conversion as
Note
necessary.
• When an HDMI IN is assigned to an input selector as explained
`1080p: here, the digital audio input for that input selector is automati-
Select this for 1080p output and video conversion as cally set to the same HDMI IN (➔ 40, Digital Audio Input).
necessary. • TUNER selector cannot be assigned and is fixed at the “- - - - -”
option.
HDMI Input • If you connect a component (such as UP-A1 Dock that seated
iPod) to UNIVERSAL PORT jack, you cannot assign any input
If you connect a video component to an HDMI input, you to PORT selector.
must assign that input to an input selector. For example, if • Do not assign the component connected with the HDMI input to
you connect your Blu-ray Disc/DVD player to HDMI TV/CD selector when you set “TV Control” setting to “On”
IN 2, you must assign “HDMI2” to the “BD/DVD” input (➔ 52). Otherwise, appropriate CEC (Consumer Electronics
selector. Control) operation will not be guaranteed.
If you’ve connected your TV to the AV receiver with an
HDMI cable, composite video and component video
sources can be upconverted* to HDMI. See “Video Con-
nection Formats” for more information on video signal
flow and upconversion (➔ 21).
En
39
Component Video Input Note
If you connect a video component to a component video • When an HDMI IN is assigned to an input selector in “HDMI
input, you must assign that input to an input selector. For Input” (➔ 39), this input assignment is automatically set to the
same HDMI IN. And in addition to the usual inputs (e.g.,
example, if you connect your Blu-ray Disc/DVD player to
COAX1, COAX2, etc.), you can also select HDMI inputs.
COMPONENT VIDEO IN 2, you must assign “IN2” to
• Available sampling rate for PCM signals from a digital input
the “BD/DVD” input selector. (optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
Here are the default assignments. • If you connect a component (such as UP-A1 Dock that seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
Input selector Default assignment input to PORT selector.
BD/DVD IN1
VCR/DVR ----- Speaker Setup
CBL/SAT IN2
GAME ----- Main menu Speaker Setup
PC -----
AUX -----
Some of the settings in this section are set automatically
by Audyssey 2EQ® Room Correction and Speaker
TUNER - - - - - (Fixed)
Setup function (➔ 25).
TV/CD -----
PORT ----- Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, manually, which is useful if you change one of the con-
TV/CD, PORT nected speakers after using Audyssey 2EQ Room Correc-
` IN1, IN2: tion and Speaker Setup function.
Select a corresponding component video input that
the video component has been connected. Note
` - - - - -: These settings are disabled when:
Select if you are using HDMI output, not component • a pair of headphones is connected, or
video output, to output composite video and compo- • the “Audio TV Out” setting is set to “On” (➔ 51) and an input
nent video sources. selector other than HDMI is selected.
Note
Speaker Settings
• If you connect a component (such as UP-A1 Dock that seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to PORT selector. If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
Digital Audio Input again (➔ 25).
If you connect a component to a digital audio input, you If the impedance of any speaker is 4 ohms or more but less
must assign that input to an input selector. For example, if than 6, set the minimum speaker impedance to 4 ohms.
you connect your CD player to the OPTICAL IN 1, you
If you bi-amp the front speakers, you must change the
must assign “OPT1” to the “TV/CD” input selector.
“Speakers Type” setting (➔ 41).
Here are the default assignments.
For hookup information, see “Bi-amping the Front Speak-
Input selector Default assignment ers” (➔ 15).
BD/DVD COAX1 Note
VCR/DVR ----- • When bi-amping is used, the AV receiver is able to drive up to
CBL/SAT COAX2 5.1 speakers in the main room.
GAME OPT1 • Before you change these settings, turn down the volume.
PC ----- ■ Speaker Impedance
AUX ----- ` 4ohms:
TUNER - - - - - (Fixed) Select if the impedance of any speaker is 4 ohms or
TV/CD OPT2 more but less than 6.
PORT ----- ` 6ohms:
Select if the impedances of all speakers are between
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, 6 and 16 ohms.
TV/CD, PORT
Note
` COAX1, COAX2, OPT1, OPT2:
• (North American and Taiwan models) Speakers with an
Select a corresponding digital audio input that the
impedance of less than 6 ohms are not supported.
component has been connected.
` - - - - -:
Select if the component is connected to an analog
En audio input.
40
■ Speakers Type ■ Subwoofer
`Normal: ` Yes:
Select this if you’ve connected your front speakers Select if a subwoofer is connected.
normally. ` No:
`Bi-Amp: Select if no subwoofer is connected.
Select this if you’ve bi-amped your front speakers.
■ Front
Note ` Full Band
• Powered Zone 2 cannot be used if “Speakers Type” is set to ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
“Bi-Amp” (➔ 56). 200Hz
■ Speaker Terminal Assign Note
Front High/Front Wide/Zone2 • If the “Subwoofer” setting is set to “No”, the “Front” setting is
With this setting, you can specify the speakers con- fixed at “Full Band”.
nected to FRONT HIGH OR FRONT WIDE OR ■ Center*1, Surround*1, Surr Back*2*3*4*5
ZONE 2 SPEAKERS terminals.
` Full Band
`Front High:
` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
Front high speakers can be used.
200Hz
`Front Wide:
` None:
Front wide speakers can be used.
Select if no speaker is connected.
`Zone2:
Zone 2 speakers can be used. (Powered Zone 2 ■ Front Wide*1*2*4*6, Front High*1*2*4*7
enabled). ` Full Band
Note ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
• If the “Speakers Type” setting is set to “Bi-Amp”, or Powered
200Hz
Zone 2 cannot be used. ` None:
Select if no speaker is connected.
SurrBack/Front High/Front Wide
With this setting, you can specify the speakers con- Note
nected to SURR BACK OR FRONT HIGH OR *1 “Full Band” can be selected only when “Full Band” is
FRONT WIDE SPEAKERS terminals. selected in the “Front” setting.
*2 If the “Surround” setting is set to “None”, this setting cannot
`Surr Back:
be selected.
Surround back speakers can be used.
*3 If the “Surround” setting is set to anything other than “Full
`Front High: Band”, “Full Band” cannot be selected here.
Front high speakers can be used. *4 If the “Speakers Type” setting is set to “Bi-Amp” (➔ 41), or
`Front Wide: Powered Zone 2 is being used (➔ 56), this setting cannot be
Front wide speakers can be used. selected.
*5 If you have selected other than “Surr Back” in the “Surr-
Note
Back/Front High/Front Wide” setting, this setting cannot be
• If the “Speakers Type” setting is set to “Bi-Amp”, or Powered selected.
Zone 2 cannot be used. *6 If you have selected other than “Front Wide” in the “Front
• If “Front High” is selected in the “Front High/Front Wide/ High/Front Wide/Zone2” or “SurrBack/Front High/Front
Zone2” setting, you cannot select “Front High” here. Wide” setting, this setting cannot be selected.
• If “Front Wide” is selected in the “SurrBack/Front High/ *7 If you have selected other than “Front High” in the “Front
Front Wide” setting, you cannot select “Front Wide” here. High/Front Wide/Zone2” or “SurrBack/Front High/Front
Wide” setting, this setting cannot be selected.
Speaker Configuration
■ Surr Back Ch
With these settings, you can specify which speakers are ` 1ch:
connected and a crossover frequency for each speaker. Select if only one surround back speaker L is con-
Specify “Full Band” for speakers that can output low fre- nected.
quency bass sounds adequately, for example, speakers ` 2ch:
with a good sized woofer. For smaller speakers, specify a Select if two (left and right) surround back speakers
crossover frequency. Sounds below the crossover fre- are connected.
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the Note
optimum crossover frequencies. If you set up your speak- • If the “Surr Back” Setting is set to “None” (➔ 48), this setting
ers using Audyssey 2EQ® Room Correction and Speaker cannot be selected.
Setup, please make sure manually that any THX speakers
are set to “80Hz(THX)” crossover.
En
41
■ LPF of LFE Here you can adjust the level of each speaker with the
(Low-Pass Filter for the LFE Channel) built-in test tone so that the volume of each speaker is the
` 80Hz, 90Hz, 100Hz, 120Hz same at the listening position.
With this setting, you can specify the cutoff frequency ■ Left, Front Wide Left, Front High Left, Center*1,
of the LFE channel’s low-pass filter (LPF), which can Front High Right, Front Wide Right, Right, Surr
be used to filter out unwanted hum. The LPF only Right, Surr Back Right, Surr Back Left, Surr Left
applies to sources that use the LFE channel.
` –12dB to 0dB to +12dB in 1 dB step.
Note
■ Subwoofer*1
• If you’re using THX-certified speakers, select “80Hz”.
` –15dB to 0dB to +12dB in 1 dB step.
■ Double Bass Note
• Speakers that you set to “No” or “None” in the
This setting is set automatically by Audyssey 2EQ® “Speaker Configuration” cannot be selected (➔ 41).
Room Correction and Speaker Setup function (➔ 25). • The speakers cannot be calibrated while the AV receiver is
muted.
With the Double Bass function, you can boost bass out- • The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at vol-
put by feeding bass sounds from the front left, right, and
ume settings below this, be careful because the test tone will be
center channels to the subwoofer. much louder.
` On: *1 For the center speaker and subwoofer, the level settings made
Double Bass function on. by using the Home menu are saved (➔ 24).
` Off: Tip
Double Bass function off.
• If you’re using a handheld sound level meter, adjust the level of
Note each speaker so that it reads 75 dB SPL at the listening position,
• This function can be set only if the “Subwoofer” setting is set to measured with C-weighting and slow reading.
“Yes”, and the “Front” setting is set to “Full Band”.
• If you’re using THX-certified speakers, select “Off”. Equalizer Settings
Speaker Distance
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function (➔ 25).
Room Correction and Speaker Setup function (➔ 25). With the Equalizer settings, you can adjust the tone of
speakers individually with a 5-band equalizer. The volume
Here you can specify the distance from each speaker to the of each speaker can be set (➔ 42).
listening position so that the sound from each speaker
■ Equalizer
arrives at the listener’s ears as the sound designer
intended. ` Manual:
You can adjust the equalizer for each speaker manu-
■ Unit ally. If you selected “Manual”, continue with this
` feet: procedure.
Distances can be set in feet. Range: 1ft to 30ft in
1 foot steps. 1 Press w to select “Channel”, and then use e/
` meters: r to select a speaker.
Distances can be set in meters. Range: 0.3m to 9.0m
in 0.3 meter steps.
2 Use q/w to select a frequency, and then use
the e/r to adjust the level at that frequency.
(The default setting varies from country to country.) The volume at each frequency can be adjusted
■ Left, Front Wide Left, Front High Left, Center, from –6dB to 0dB to +6dB in 1 dB steps.
Front High Right, Front Wide Right, Right, Surr Tip
Right, Surr Back Right, Surr Back Left, Surr • Low frequencies (e.g., 63Hz) affect bass sounds;
Left, Subwoofer high frequencies (e.g., 16000Hz) affect treble
` Specify the distance from the each speaker to your lis- sounds.
3
tening position.
Use q to select “Channel”, and then use e/r
Note to select another speaker.
• Speakers that you set to “No” or “None” in the Speaker Config- Repeat steps 1 and 2 for each speaker.
uration cannot be selected (➔ 41). You cannot select speakers that you set to “No”
or “None” in the “Speaker Configuration”
Level Calibration (➔ 41).

En Room Correction and Speaker Setup function (➔ 25).
42
Àudyssey: ■ BGC
This is selected automatically by Audyssey 2EQ® ` Off:
Room Correction and Speaker Setup function. The Select this to turn off BGC.
Audyssey Dynamic Volume indicator will light ` On:
(➔ 9) and “Dynamic EQ” and “Dynamic Volume” Select this to turn on BGC.
become available (➔ 45).
Note
Òff:
• This setting is only available if “THX Ultra2/Select2 Sub-
No Audyssey 2EQ equalizing will apply.
woofer” is set to “Yes”.
Note
■ Loudness Plus
• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or
“16000Hz”. And for the subwoofer, “25Hz”, “40Hz”, “63Hz”, ` Off:
“100Hz”, or “160Hz”. Select this to turn off Loudness Plus.
• While the Direct or Pure Audio (European, Australian, and ` On:
Asian models) listening mode is selected, the equalizer settings Select this to turn on Loudness Plus.
have no effect.
• Audyssey equalizing does not work for DSD sources. ■ Preserve THX Settings
` Yes:
THX Audio Setup Audyssey Dynamic EQ™ /
Audyssey Dynamic Volume™ will not be active in
With the “SurrBack Speaker Spacing” setting, you can THX listening mode.
specify the distance between your surround back speakers. ` No:
If you’re using a THX-certified subwoofer, set the “THX Audyssey Dynamic EQ /
Ultra2/Select2 Subwoofer” setting to “Yes”. You can Audyssey Dynamic Volume will be active in THX
then apply THX’s Boundary Gain Compensation (BGC) listening mode depending on the setting.
to compensate the perceived exaggeration of low frequen-
Note
cies for listeners sitting very close to a room boundary
(i.e., wall). • This setting is fixed at “Yes” if “Loudness Plus” is set to “On”.
You can also set the THX Loudness Plus. When the
“Loudness Plus” is set to “On”, it is possible to enjoy THX Loudness Plus
even subtle nuances of audio expression at low volume. THX Loudness Plus is a new volume control technology
This result is only available when the THX listening mode featured in THX Ultra2 Plus™ and THX Select2 Plus™
is selected. Certified receivers. With THX Loudness Plus, home
theater audiences can now experience the rich details in
■ SurrBack Speaker Spacing
a surround mix at any volume level. A consequence of
`< 1ft (< 0.3m): turning the volume below Reference Level is that cer-
Select this if your surround back speakers are tain sound elements can be lost or perceived differently
between 0 and 1 foot (0–30 cm) apart. by the listener. THX Loudness Plus compensates for the
`1 ft - 4 ft (0.3 m - 1.2 m): tonal and spatial shifts that occur when the volume is
Select this if your surround back speakers are reduced by intelligently adjusting ambient surround
between 1 and 4 feet (0.3–1.2 m) apart. channel levels and frequency response. This enables
`> 4ft (> 1.2m): users experience the true impact of soundtracks regard-
Select this if your surround back speakers are more less of the volume setting. THX Loudness Plus is auto-
than 4 feet (1.2 m) apart. matically applied when listening in any THX listening
Note mode. The new THX Cinema, THX Music, and THX
Cannot be set if “Surr Back Ch” is set to “1ch” (➔ 41), Games modes are tailored to apply the proper THX
“Speakers Type” is set to “Bi-Amp” (➔ 41), “Surr Loudness Plus settings for each type of content.
Back” is set to “None” (➔ 41), or Powered Zone 2 is
being used (➔ 56).
■ THX Ultra2/Select2 Subwoofer
`No:
Select this if you do not have a THX-certified sub-
woofer.
`Yes:
Select this if you have a THX-certified subwoofer.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot be
selected (➔ 41).
En
43
With this setting, you can broaden the width of the front
Audio Adjust
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
Main menu Audio Adjust
Dimension
With the Audio Adjust functions and settings, you can ` –3 to 0 to +3
adjust the sound and listening modes as you like.
With this setting, you can move the sound field forward
or backward when using the Dolby Pro Logic IIx Music
Multiplex/Mono
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
■ Multiplex
If the stereo image feels too wide, or there’s too much
This setting determines which channel of a stereo multi-
surround sound, move the sound field forward to
plex source is output. Use it to select audio channels or
improve the balance. Conversely, if the stereo image
languages with multiplex sources, multilingual TV
feels like it’s in mono, or there’s not enough surround
broadcasts, and so on.
sound, move it backward.
Input Channel
Center Width
` Main:
` 0 to 3 to 7
The main channel is output.
With this setting, you can adjust the width of the sound
` Sub:
from the center speaker when using the Dolby Pro
The sub channel is output.
Logic IIx Music listening mode. Normally, if you’re
` Main/Sub: using a center speaker, the center channel sound is out-
Both the main and sub channels are output. put by only the center speaker. (If you’re not using a
■ Mono center speaker, the center channel sound will be distrib-
This setting specifies the channel to be used for playing uted to the front left and right speakers to create a phan-
any 2-channel digital source such as Dolby Digital, or tom center). This setting controls the front left, right,
2-channel analog/PCM source in the Mono listening and center mix, allowing you to adjust the weight of the
mode. center channel sound.
Input Channel ■ PLIIz Height Gain
` Left + Right: The Height Gain Control in Dolby Pro Logic IIz
Both the left and right channels are output. enables the listener to select how much gain is applied
` Left: to the front high speakers. There are three settings,
Only the left channel is output. “Low”, “Mid” and “High”, and the front high speakers
` Right: are accentuated in that order. While “Mid” is the default
Only the right channel is output. listening setting, the listener may adjust the Height Gain
Control to their personal preference.
Output Speaker
` Low:
` Center:
Low PLIIz Height Gain becomes active.
Mono audio is output by the center speaker.
` Mid:
` Left / Right:
Medium PLIIz Height Gain becomes active.
Mono audio is output by the front left and right
speakers. ` High:
High PLIIz Height Gain becomes active.
This setting determines which speakers output mono
audio when the Mono listening mode is selected. Note
• If the “Front High” settings is set to “None” (➔ 41), this setting
Note
cannot be selected.
• If the “Center” setting is set to “None” (➔ 41), this setting is
fixed at “Left / Right”. ■ Dolby EX
This setting determines how Dolby EX encoded signals
Dolby are handled. This setting is unavailable if no surround
back speakers are connected. This setting is effective
■ PLIIx Music (2ch Input) with Dolby Digital, Dolby Digital Plus and Dolby
These settings apply to only 2-channel stereo sources. TrueHD only.
If you’re not using any surround back speakers, these Dolby EX
settings apply to Dolby Pro Logic II, not Dolby Pro ` Auto:
Logic IIx. If the source signal contains a Dolby EX flag, the
Panorama Dolby EX or THX Surround EX listening mode is
` On: used.
Panorama function on. ` Manual:
` Off: You can select any available listening mode.
Panorama function off.
En
44
Note LFE Level
• If the “Surr Back” setting is set to “None” (➔ 41), this setting
cannot be selected. ■ Dolby Digital*1, DTS*2, Multich PCM, Dolby
• If the “Front High” or “Front Wide” setting is enabled (➔ 41), TrueHD, DTS-HD Master Audio, DSD*3
this setting is fixed at “Manual”. ` –QdB, –20dB, –10dB, or 0dB
With these settings, you can set the level of the LFE (Low
DTS Frequency Effects) channel individually for each input
sources.
■ Neo:6 Music If you find that low-frequency effects are too loud when
Center Image using one of these sources, change the setting to –20 dB or
`0 to 2 to 5 –Q dB.
The DTS Neo:6 Music listening mode creates 6-channel *1 Dolby Digital and Dolby Digital Plus sources
surround sound from 2-channel stereo sources. With *2 DTS and DTS-HD High Resolution sources
this setting, you can specify by how much the front left *3 DSD (Super Audio CD) sources
and right channel output is attenuated in order to create
the center channel. Source Setup
Setting a value “0” in the middle is set to hear a sound.
Sound is spread in left and right (the outside) so that the Items can be set individually for each input selector.
set value is made big. Please adjust by liking.
Preparation
Audyssey DSX™ Press the input selector buttons to select an input source.
■ Soundstage Main menu Source Setup

`–3dB, to Reference to +3dB
With this setting, you can adjusts the soundstage when
using Audyssey DSX™. Audyssey
Note When Audyssey 2EQ® Room Correction and Speaker

• If the “Center” setting is set to “None”, or both “Front High” Setup is complete, the “Equalizer” (➔ 42) will be set to
and “Front Wide” settings are set to “None” (➔ 41), this setting “Audyssey” and the “Dynamic EQ” will be set to “On”.
cannot be selected.
■ Dynamic EQ
` Off:
Theater-Dimensional
Audyssey Dynamic EQ™ off.
` On:
■ Listening Angle
Audyssey Dynamic EQ on.
`Wide:
The Dynamic EQ indicator will light (➔ 9).
Select if the listening angle is 40 degrees.
With Audyssey Dynamic EQ, you can enjoy great
`Narrow:
sound even when listening at low volume levels.
Select if the listening angle is 20 degrees.
Audyssey Dynamic EQ solves the problem of deterio-
With this setting, you can optimize the Theater-Dimen-
rating sound quality as volume is decreased by taking
sional listening mode by specifying the angle of the
into account human perception and room acoustics. It
front left and right speakers relative to the listening
does so by selecting the correct frequency response and
position. Ideally, the front left and right speakers should
surround volume levels moment-by-moment so that the
be equidistant from the listening position and at an
content sounds the way it was created at any volume
angle close to one of the two available settings.
level — not just at reference level.
Front left speaker Front right speaker Note
• If Pure Audio (European, Australian and Asian models) or
20°/40° Direct listening mode is selected, this setting cannot be selected.
En
45
■ Reference Level • When “Dynamic Volume” is set to effective, “Equalizer” is set
Audyssey Dynamic EQ™ Reference Level Offset to “Audyssey” (➔ 42) and “Dynamic EQ” is set to “On”.
When “Dynamic EQ” is set to “Off”, “Dynamic Volume”
` 0dB:
becomes “Off” automatically.
It should be used when listening to movies. • When “Dynamic Volume” is set to effective, the Dynamic Vol
` 5dB: indicator will light (➔ 9).
Select this setting for content that has a very wide • If Pure Audio (European, Australian and Asian models) or
dynamic range, such as classical music. Direct listening mode is selected, this setting cannot be selected.
` 10dB: Audyssey 2EQ then removes the distortion caused by
Select this setting for jazz or other music that has a room acoustics by capturing room acoustical problems
wider dynamic range. This setting should also be over the listening area in both the frequency and time
selected for TV content as that is usually mixed at domain. The result is clear, well-balanced sound for every-
10 dB below film reference. one. Enabling Audyssey 2EQ allows you to also use
` 15dB: Audyssey Dynamic EQ, which maintains the proper
Select this setting for pop/rock music or other pro- octave-to-octave balance at any volume level.
gram material that is mixed at very high listening Before using this function, connect and position all of
levels and has a compressed dynamic range. your speakers.
Movies are mixed in rooms calibrated for film refer-
ence. To achieve the same reference level in a home the- About Audyssey Dynamic EQ
ater system each speaker level must be adjusted so that Audyssey Dynamic EQ solves the problem of deterio-
–30 dBFS band-limited (500 Hz to 2000 Hz) pink noise rating sound quality as volume is decreased by taking
produces 75 dB sound pressure level at the listening into account human perception and room acoustics.
position. A home theater system automatically cali- Dynamic EQ selects the correct frequency response and
brated by Audyssey 2EQ® will play at reference level surround levels moment-by-moment at any user-
when the master volume control is set to the 0 dB posi- selected volume setting. The result is bass response,
tion. At that level you can hear the mix as the mixers tonal balance, and surround impression that remain con-
heard it. stant despite changes in volume. Dynamic EQ combines
Audyssey Dynamic EQ™ is referenced to the standard information from incoming source levels with actual
film mix level. It makes adjustments to maintain the ref- output sound levels in the room, a prerequisite for deliv-
erence response and surround envelopment when the ering a loudness correction solution.
volume is turned down from 0 dB. However, film refer- Audyssey Dynamic EQ works in tandem with
ence level is not always used in music or other non-film Audyssey 2EQ to provide well-balanced sound for
content. Audyssey Dynamic EQ Reference Level Offset every listener at any volume level.
provides three offsets from the film level reference
(5 dB, 10 dB, and 15 dB) that can be selected when the
About Audyssey Dynamic Volume
mix level of the content is not within the standard.
Audyssey Dynamic Volume solves the problem of large
Note variations in volume level between television programs,
• If “Dynamic EQ” setting is set to “Off”, this setting cannot be commercials, and between the soft and loud passages of
selected. movies. Dynamic Volume looks at the preferred volume
setting by the user and then monitors how the volume of
■ Dynamic Volume
program material is being perceived by listeners in real
` Off:
time to decide whether an adjustment is needed. When-
Audyssey Dynamic Volume™ off.
ever necessary, Dynamic Volume makes the necessary
` Light: rapid or gradual adjustments to maintain the desired
Light Compression Mode becomes active. playback volume level while optimizing the dynamic
` Medium: range. Audyssey Dynamic EQ is integrated into
Medium Compression Mode becomes active. Dynamic Volume so that as the playback volume is
` Heavy: adjusted automatically, the perceived bass response,
Heavy Compression Mode becomes active. This set- tonal balance, surround impression, and dialog clarity
ting affects volume the most, causing all sounds to remain the same whether watching movies, flipping
be of equal loudness. between television channels, or changing from stereo to
Note surround sound content.
• Even if you have selected other than “Audyssey” in “Equalizer”
setting after performing Audyssey 2EQ® Room Correction and
Speaker Setup, selecting “On” in the “Dynamic EQ” will
change the “Equalizer” setting to “Audyssey” (➔ 42).
• If you would like to use Audyssey Dynamic Volume, when
using THX listening modes, set “Loudness Plus” setting to
“Off” and set “Preserve THX Settings” setting to “No” (➔ 43).
En
46
IntelliVolume Name input area
■ IntelliVolume 4 - 4. Name Edit BD/DVD

`–12dB to 0dB to +12dB in 1 dB steps. Name
With IntelliVolume, you can set the input level for each a b c d e f g h i j k l m
input selector individually. This is useful if one of your n o p q r s t u v w x y z
1 2 3 4 5 6 7 8 9 0 – `
source components is louder or quieter than the others. { } | : < > ?
Shift Space Back Space OK
Use e/r to set the level.
If a component is noticeably louder than the others, use e +10 Shift CLR All Erase
to reduce its input level. If it’s noticeably quieter, use r to

increase its input level. A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
Note ! @ # $ % ^ & ( ) _ ~
[ ] ; ’ , . /
• IntelliVolume does not apply for Zone 2. Shift Space Back Space OK
+10 Shift CLR All Erase

A/V Sync
■ A/V Sync
`0ms to 200ms in 10 ms steps. Shift*1:
When using your DVD player’s progressive scanning Switches the displayed character.
function, you may find that the picture and sound are out (Left)/ (Right):
of sync. With the A/V Sync setting, you can correct this Selected when the cursor is moved within
by applying a delay to the audio signal. the Name input area.
To view the TV picture while setting the delay, press BackSpace*2:
ENTER. “BackSpace” moves the cursor backward
To return to the previous screen, press RETURN. one character space. In addition, “Back-
Space” deletes the character to the left of the
If HDMI Lip Sync is enabled (➔ 51) and your TV or dis- cursor.
play supports HDMI Lip Sync, the displayed delay time Tip
will be the summation of the A/V Sync delay time and the *1 You can also be performed on the remote con-
HDMI Lip Sync delay time. The HDMI Lip Sync delay troller by using +10.
time is displayed underneath in parentheses. *2 Press CLR on the remote controller, you can
Note delete all characters in the input.
• A/V Sync is disabled when the Pure Audio (European, Austra-
OK:
lian and Asian models) listening mode is selected, or when the Selects when the entry is complete.
Direct listening mode is used with an analog input source.
Name Edit
You can enter a custom name for each individual input
selector and radio preset for easy identification. When To correct a character:
entered, the custom name will appear on the display.
The custom name is edited using the character input 1 Use q/w/e/r to select “ ”(Left) or
screen. “ ”(Right), and then press ENTER.
■ Name 2 Press ENTER several times to select the incor-
rect character (The cursor moves one letter
1 Use q/w/e/r to select a character, and then each time ENTER is pressed).
press ENTER.
Repeat this step to enter up to 10 characters.
3 Use q/w/e/r to select the correct character,
and then press ENTER.
2 When you’ve finished, to store a name, be sure
Note
to use q/w/e/r to select “OK”, and then press
ENTER. Otherwise it will not be saved. • To name a radio preset, use TUNER to select AM or FM, and
then select the preset (➔ 47).
• You cannot enter a custom name for SIRIUS radio presets.
To restore a custom name to the default, erase the custom
name by entering an empty white space for each letter.
En
47
Picture Adjust ` Zoom:
Using Picture Adjust, you can adjust the picture quality

and reduce any noise appearing on the screen.
To view the TV picture while setting, press ENTER. To
return to the previous screen, press RETURN.
Note
• If you are using the analog RGB input, the following settings are
not available: “Film Mode”, “Edge Enhancement”, and “Noise
Reduction”.
■ Game Mode
` Off:
Game Mode off.
` On:
Game Mode on.
` Wide Zoom:
If video signal delay occurs during playback on a video
component (i.e. game console), select the corresponding
input source and set the “Game Mode” setting to “On”.
The delay will decrease but in return the picture quality
will become poor.
■ Wide Mode*1*2
This setting determines the aspect ratio.
Note
• When the “Game Mode” is set to “On”, this setting is fixed at
“Full”.
` 4 : 3:
` Auto:
According to the input signals and monitor output
setting, the AV receiver automatically selects the
“4 : 3”, “Full”, “Zoom” or “Wide Zoom” mode. For
the monitor output setting (➔ 39).
■ Picture Mode*1*2
` Thru:
The following settings are set to the default values:
“Film Mode”, “Edge Enhancement”, “Noise
Reduction”, “Brightness”, “Contrast”, “Hue” and
` Full: “Saturation”
` Custom:
You can set the following settings as you like: “Film
Mode”, “Edge Enhancement”, “Noise Reduction”,
“Brightness”, “Contrast”, “Hue” and “Saturation”
` Cinema:
Selected when the picture source is movie film, etc.
` Game:
Select to use in connecting a game console.
With Picture Mode, you can change the following settings
to be suitable for the movie or game screen by one opera-
tion; “Film Mode”, “Edge Enhancement”, “Noise
Reduction”, “Brightness”, “Contrast”, “Hue” or “Satu-
ration”.
En
48
■ Film Mode*2 ■ Saturation*1*2
`Video: ` –50 to 0 to +50
Does not process in either “3 : 2” or “2 : 2”. With this setting you can adjust saturation. “–50” is
Àuto: the weakest color. “+50” is the strongest color.
Adjusts to the picture source, automatically selecting Tip
“Picture Mode”. *1 This procedure can also be performed on the remote controller
`3 : 2: by using the Home menu (➔ 24).
Selected when the picture source is movie film, etc. *2 Press CLR if you want to reset to the default value.
`2 : 2:
Selected when the picture source is computer graph-
Listening Mode Preset
ics, animation, etc.
The AV receiver will adjust to the picture source, process- You can assign a default listening mode to each input
ing in either “3 : 2” or “2 : 2” (Film Mode). It automati- source that will be selected automatically when you select
cally converts the source to the appropriate progressive each input source. For example, you can set the default lis-
signal and reproduces the natural quality of the original tening mode to be used with Dolby Digital input signals.
picture. You can select other listening modes during playback, but
When the “Film Mode” setting is set to “Auto”, the AV the mode specified here will be resumed once the AV
receiver automatically detects the picture source and in receiver has been set to Standby.
either “3 : 2” or “2 : 2”. However, there may be times
Main menu Listening Mode Preset
when you will get a better picture by setting “Film Mode”
yourself. 1 Use q/w to select the input source that you want to
set, and then press ENTER.
Note The following menu appears.
• If the “Game Mode” setting is set to “On” (➔ 48), this setting
is fixed at “Video”. 5. Listening Mode Preset
1. BD/DVD
■ Edge Enhancement*2 2.
3.
VCR/DVR
CBL/SAT
`0 to +10 4.
5.
GAME
PC
6. AUX
With this setting you can adjust the sharpness of edges in 7. TUNER
8. TV/CD
the picture. “0” is the softest. “+10” is the sharpest. 9. PORT
■ Noise Reduction*2 For TUNER input selector only “Analog” will be

Òff: available.
Noise reduction off.
Note
`Low:
• If you connect an input component (such as UP-A1 series
Low noise reduction.
Dock that seated iPod) to the UNIVERSAL PORT jack,
`Mid: you can assign only listening modes for the analog sound
Medium noise reduction. to PORT selector.
`High:
High noise reduction. 2 Use q/w to select the signal format that you want
With this setting, you can reduce noise appearing on the to set, and then use e/r to select a listening mode.
screen. Only listening modes that can be used with each
input signal format can be selected (➔ 33 to 37).
Note The “Last Valid” option means that the listening
• If the “Game Mode” setting is set to “On” (➔ 48), this setting mode selected last will be used.
is fixed at “Off”.
■ Analog / PCM
■ Brightness*1*2
With this setting, you can specify the listening mode to
`–50 to 0 to +50
be used when an analog (CD, TV, LD, VHS, MD, turn-
With this setting you can adjust the picture bright-
table, radio, cassette, cable, satellite, etc.) or PCM digi-
ness. “–50” is the darkest. “+50” is the brightest.
tal (CD, DVD, etc.) audio signal is played.
■ Contrast*1*2
■ Mono/Multiplex Source
`–50 to 0 to +50
With this setting you can adjust contrast. “–50” is the
be used when a mono digital audio signal is played
least. “+50” is the greatest.
(DVD, etc.).
■ Hue*1*2
■ 2ch Source
`–20 to 0 to +20
With this setting, the default listening mode for 2-chan-
With this setting you can adjust the red/green bal-
nel (2/0) stereo sources in a digital format, such as
ance. “–20” is the strongest green. “+20” is the
Dolby Digital or DTS.
strongest red.
En
49
■ Dolby D/Dolby D +/TrueHD ■ Headphone Level
With this setting, you can specify the listening mode to ` –12dB to 0dB to +12dB
be used when a Dolby Digital or Dolby Digital Plus for- With this preference, you can specify the headphone vol-
mat digital audio signal is played (DVD, etc.). Specifies ume relative to the main volume. This is useful if there’s a
the default listening mode for Dolby TrueHD sources, volume difference between your speakers and your head-
such as Blu-ray or HD DVD (input via HDMI). phones.
■ DTS/DTS-ES/DTS-HD
OSD Setup
be used when a DTS or DTS-HD High Resolution for-
■ On Screen Display
mat digital audio signal is played (DVD, LD, CD, etc.).
Specifies the default listening mode for DTS-HD Mas- This preference determines whether operation details
ter Audio sources, such as Blu-ray or HD DVD (input are displayed on-screen when an AV receiver function is
via HDMI). adjusted.
` On:
■ Other Multich Source Displayed.
Specifies the default listening mode for multichannel ` Off:
PCM sources from HDMI IN such as DVD-Audio, and Not displayed.
DSD multichannel sources such as Super Audio CD. Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
Miscellaneous ■ TV Format (European, Australian and Asian
models)
Main menu Miscellaneous
For the on-screen setup menus to display properly, you
must specify the TV system used in your area.
Volume Setup ` Auto:
Select this to automatically detect the TV system
■ Volume Display from the video input signals.
` Absolute: ` NTSC:
Display range is “Min”, 1 through 99, “Max”. Select this if the TV system in your area is NTSC.
` Relative (THX): ` PAL:
Display range is –QdB, –81dB through +18dB. Select this if the TV system in your area is PAL.
With this setting, you can choose how the volume level is
■ Language
displayed.
` English, Deutsch, Français, Español, Italiano, Ned-
The absolute value 82 is equivalent to the relative value
0 dB. erlands, Svenska, 中文
This setting determines the language used for the on-
■ Muting Level screen setup menus.
` –QdB (fully muted), –50dB to –10dB in 10 dB steps.
This setting determines how much the output is muted Hardware Setup
when the muting function is used (➔ 24).
■ Maximum Volume Main menu Hardware Setup
` Off, 50 to 99 (Absolute display)
` Off, –32dB to +17dB (Relative display) Remote ID
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”. ■ Remote ID
` 1, 2, or 3
■ Power On Volume
When several Onkyo components are used in the same
` Last, Min, 1 to 99 or Max (Absolute display)
room, their remote ID codes may overlap. To differenti-
` Last, –Q dB, –81dB to +18dB (Relative display) ate the AV receiver from the other components, you can
With this preference, you can specify the volume set- change its remote ID from “1”, to “2” or “3”.
ting to be used each time the AV receiver is turned
on. Note
To use the same volume level that was used when the AV • If you do change the AV receiver’s remote ID, be sure to change
receiver was turned off, select “Last”. the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
The “Power On Volume” cannot be set higher than the
“Maximum Volume” setting.
En
50
Changing the Remote Controller’s ID • With some TVs and input signals, no sound may be output even
when this setting is set to “On” (➔ 52).
1 While holding down RECEIVER, press and hold
down SETUP until the remote indicator lights
• When the “Audio TV Out” setting is set to “On”, or “TV Con-
trol” is set to “On” (➔ 52) and you’re listening through your
(about 3 seconds) (➔ 38). TV’s speakers (➔ 17), if you turn up the AV receiver’s volume
control, the sound will be output by the AV receiver’s front left
2 Use the number buttons to enter ID 1, 2, or 3. and right speakers. To stop the AV receiver’s speakers producing
The remote indicator flashes twice. sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
TUNER ■ Lip Sync
For FM/AM tuning to work properly, you must specify the ` Disable:
FM/AM frequency step used in your area. Note that when HDMI lip sync disabled.
this setting is changed, all radio presets will be deleted. ` Enable:
HDMI lip sync enabled.
■ FM/AM Frequency Step (North American and
The AV receiver can be set to automatically correct any
Taiwan models)
delay between the video and the audio, based on the data
`200k/10kHz:
from the connected monitor.
Select if 200 k/10 kHz steps are used in your area.
`50k/9kHz: Note
Select if 50 k/9 kHz steps are used in your area. • This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
■ AM Frequency Step (European, Australian and • You can check the amount of delay being applied by the HDMI
Asian models) Lip Sync function on the A/V Sync screen.
`10kHz:
■ HDMI Control (RIHD)
Select if 10 kHz steps are used in your area.
` Off:
`9kHz:
Select if 9 kHz steps are used in your area. p disabled.
` On:
SIRIUS Settings (North American models) p enabled.
This function allows p-compatible components
See the separate Satellite Radio Guide for more informa- connected via HDMI to be controlled with the AV receiver
tion. (➔ 72 to 73).
■ SAT Radio Mode Note
If you connect a SIRIUS Satellite Radio antenna to the • When set to “On” and close the menu, the name of connected
AV receiver (sold separately), set this setting to “SIR- p-compatible components and “RIHD On” are dis-
IUS”. played on the AV receiver.
“Search…” → “(name)” → “RIHD On”
■ Antenna Aiming
When the AV receiver cannot receive the name of the compo-
■ SIRIUS Parental Lock nent, it is displayed as “Player*” or “Recorder*”, etc (“*” means
These items are for use with SIRIUS Satellite Radio. the number of two or more component).
It’s not available if “SAT Radio Mode” is set to When set to “Off” and close the menu, “RIHD Off” are dis-
played on the AV receiver.
“None”.
“Disconnect” → “RIHD Off”
• When an p-compatible component is connected to the
HDMI AV receiver via the HDMI cable, the name of the connected
component is displayed on the AV receiver display. For example,
■ Audio TV Out while you are watching TV broadcasting, if you operate a
Òff: Blu-ray Disc/DVD player (being powered on) by the remote
HDMI audio is not output. control of the AV receiver, the name of the Blu-ray Disc/DVD
Òn: player is displayed on the AV receiver.
• Set to “Off” when a connected piece of equipment is not com-
HDMI audio is output.
patible or it is unclear whether the equipment is compatible or
This preference determines whether audio received at the not.
HDMI IN is output by the HDMI OUT. You may want to • If movement is unnatural when set to “On”, change the setting
turn this preference on if your TV is connected to the to “Off”.
HDMI OUT and you want to listen to the audio from a • Refer to the connected component’s instruction manual for
component that’s connected to an HDMI IN, through your details.
TV’s speakers. Normally, this should be set to “Off”.
Note
• If “On” is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, “TV Sp On” appears on the display.
• When “TV Control” is set to “On”, this setting is fixed to En
“Auto”.
51
■ Audio Return Channel Note
` Off:
• Do not assign the component connected with the HDMI input to
Select “Off” if you don’t want to use audio return the TV/CD selector when you set “TV Control” setting to “On”.
channel (ARC) function. Otherwise, appropriate CEC (Consumer Electronics Control)
` Auto: operation is not guaranteed.
The audio signal from your TV tuner can be sent to • Set to “Off” when the TV is not compatible or when it is unclear
the HDMI OUT of the AV receiver. whether the TV is compatible or not.
Audio return channel (ARC) function enables an HDMI • The “TV Control” setting can be set only when the “HDMI
1.4 capable TV to send the audio stream to the HDMI Control” (➔ 51) and “Power Control” settings are both set to
OUT of the AV receiver. To use this function, you must “On”.
• Refer to the connected component’s instruction manual for
select the TV/CD input selector and your TV must support
details.
ARC function.
Note After changing the settings of the “HDMI Control”,
• The “Audio Return Channel” setting can be set only when the “Audio Return Channel”, “Power Control”, or “TV
“HDMI Control” setting is set to “On”. Control”, turn off the power to all connected pieces of
• This setting is set to “Auto” automatically when the “HDMI
equipment and then turn them on again. Refer to the
Control” is set to “On” first time.
user’s manuals for all connected pieces of equipment.
■ Power Control
` Off: Lock Setup
Power Control disabled.
` On: With this preference, you can protect your settings by
Power Control enabled. locking the setup menus.
To link the power functions of p-compatible com- Main menu Lock Setup
ponents connected via HDMI, select “On”.
This setting is set to “On” automatically when the ■ Setup
“HDMI Control” is set to “On” first time. ` Locked:
Note Setup menus locked.
` Unlocked:
• The “Power Control” setting can be set only when the “HDMI
Control” setting is set to “On”.
Setup menus not locked.
• HDMI power control only works with p-compatible When the setup menus are locked, you cannot change any
components that support it and may not work properly with setting.
some components due to their settings or compatibility.
• When set to “On”, power consumption will increase. Using the Audio Settings
• When set to “On”, regardless of whether the AV receiver is On
or in Standby, both audio and video stream from an HDMI input You can change various audio settings from the Home
will be output to the TV or other components via HDMI connec- menu (➔ 24).
tion (HDMI pass through function). When the HDMI pass
through function activates in standby mode, HDMI THRU indi- Note
cator will light. These settings are disabled when:
• The power consumption during standby mode will increase dur-
• a pair of headphones is connected, or
ing the HDMI pass through function; however in the following
• the “Audio TV Out” setting is set to “On” (➔ 51) and an input
cases, the power consumption can be saved:
selector other than HDMI is selected.
1. The TV is in standby mode.
2. You are watching a TV program.
• Refer to the connected component’s instruction manual for Tone Control Settings
details.
You can adjust the bass and treble for the front speakers,
■ TV Control except when the Direct, Pure Audio (European, Austra-
` Off: lian and Asian models) or THX listening mode is
TV Control disabled. selected.
` On: ■ Bass
TV Control enabled. ` –10dB to 0dB to +10dB in 2 dB steps.
Set to “On” when you want to control the AV receiver You can boost or cut low-frequency sounds output
from an p-compatible TV that is connected to by the front speakers.
HDMI.
■ Treble
` –10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output
by the front speakers.
En
52
Note Note
• To bypass the bass and treble tone circuits, select the Direct, Pure • The effect of the Late Night function depends on the material
Audio (European, Australian and Asian models) or THX lis- that you are playing and the intention of the original sound
tening mode. designer, and with some material there will be little or no effect
• Alternatively, you can use the AV receiver’s TONE and TONE when you select the different options.
LEVEL +/– (➔ 54). • The Late Night function can be used only when the input source
is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.
Speaker Levels • The Late Night function is set to “Off” when the AV receiver is
set to Standby. For Dolby TrueHD sources, it will be set to
You can adjust the volume of each speaker while listening “Auto”.
to an input source.
These temporary adjustments are cancelled when the AV Music Optimizer
receiver is set to Standby. To save the setting you made
The Music Optimizer function enhances the sound quality
here, go to “Level Calibration” (➔ 42) before setting the
of compressed music files. Use it with music files that use
AV receiver to Standby.
“lossy” compression, such as MP3.
■ Subwoofer Level
■ Music Optimizer
`–15dB to 0dB to +12dB in 1 dB steps.
` Off:
■ Center Level Music Optimizer off.
`–12dB to 0dB to +12dB in 1 dB steps. ` On:
Note Music Optimizer on. The M.Opt indicator will light
(➔ 9).
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in the Note
“Speaker Configuration” (➔ 41) cannot be adjusted. • The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and ana-
Audyssey Settings log audio input signals. The Music Optimizer is disabled when
the Direct or Pure Audio (European, Australian and Asian
■ Dynamic EQ models) listening mode is selected.
• The setting is stored individually for each input selector.
■ Dynamic Volume
See “Dynamic EQ” and “Dynamic Volume” of “Source Re-EQ
Setup” (➔ 45).
With the Re-EQ function, you can compensate a
Late Night soundtrack whose high-frequency content is too harsh,
making it more suitable for home theater viewing.
With the Late Night function, you can reduce the dynamic
■ Re-EQ
range of Dolby Digital material so that you can still hear
quiet parts even when listening at low volume levels— ` Off:
ideal for watching movies late at night when you don’t Re-EQ Function off.
want to disturb anyone. ` On:
Re-EQ Function on.
■ Late Night This function can be used with the following listening
For Dolby Digital and Dolby Digital Plus sources, the modes: Dolby Digital, Dolby Digital Plus,
options are: Dolby TrueHD, Multichannel, DTS, DTS-HD High Reso-
Òff: lution Audio, DTS-HD Master Audio, DTS Express,
Late Night function off. DSD, Dolby EX, Dolby Pro Logic IIz Height, Dolby
`Low: PLIIx Movie, Neo:6 Cinema and 5.1-channel source +
Small reduction in dynamic range. Neo:6.
`High:
■ Re-EQ(THX)
Large reduction in dynamic range.
` Off:
For Dolby TrueHD sources, the options are: Re-EQ (THX) Function off.
Àuto: ` On:
The Late Night function is set to “On” or “Off” Re-EQ (THX) Function on.
automatically. This function can be used with the following listening
Òff: modes: THX Cinema, THX Surround EX, and
Late Night function off. THX Select2 Cinema.
Òn:
Note
Late Night function on.
• Settings for the Re-EQ function are kept in each listening mode.
However, in THX listening mode, when the AV receiver is
turned off, it will return to “On”.
En
53
Audio Selector Setting the Incoming Digital Signal (Fixed
Mode)
You can set priorities of audio output when there are both
digital and analog inputs. By pressing ENTER while selecting “HDMI”, “COAX”,
“OPT” in the “Audio Selector”, you can specify the input
■ Audio Selector
signal in the Fixed Mode. Pressing ENTER again allows
` ARC:
you to return to the “Audio Selector” setting.
The audio signal from your TV tuner can be sent to
Normally, the AV receiver detects the signal format auto-
the HDMI OUT of the AV receiver.*1
matically. However, if you experience either of the follow-
With this selection the TV’s audio can be automati-
ing issues when playing PCM or DTS material, you can
cally selected as a priority among other assignments.
manually set the signal format to PCM or DTS.
` HDMI:
• If the beginnings of tracks from a PCM source are cut
This can be selected when HDMI IN has been
off, try setting the format to PCM.
assigned as an input source. If both HDMI (HDMI
IN) and digital audio inputs (COAXIAL IN or OPTI- • If noise is produced when fast forwarding or reversing a
CAL IN) have been assigned, HDMI input is auto- DTS CD, try setting the format to DTS.
matically selected as a priority. ` Auto:
` COAX: The format is detected automatically. If no digital
This can be selected when COAXIAL IN has been input signal is present, the corresponding analog
assigned as an input source. If both coaxial and opti- input is used instead.
cal inputs have been assigned, coaxial input is auto- ` PCM:
matically selected as a priority. Only 2-channel PCM format input signals will be
` OPT: heard. If the input signal is not PCM, the PCM indi-
This can be selected when OPTICAL IN has been cator will flash and noise may also be produced.
assigned as an input source. If both coaxial and opti- ` DTS:
cal inputs have been assigned, optical input is auto- Only DTS (but not DTS-HD) format input signals
matically selected as a priority. will be heard. If the input signal is not DTS, the DTS
` Analog: indicator will flash and there will be no sound.
The AV receiver always outputs analog signals. Note
Note • The setting is stored individually for each input selector.
• The setting will be reset to “Auto” when you change the setting
• The setting is stored individually for each input selector.
in the “Audio Selector” (➔ 54).
• This setting can be made only for the input source that is
assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.
*1 You can select “ARC” if you select the TV/CD input selector. Adjusting the Bass & Treble
But you cannot select it if you’ve selected “Off” in the “Audio
Return Channel” setting (➔ 52). You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio (European, Australian
and Asian models) or THX listening mode is selected.
1 Press TONE on the AV receiver repeatedly to

select either “Bass” or “Treble”.
2 Use TONE LEVEL +/– on the AV receiver to

adjust.
■ Bass
■ Treble
See “Bass” and “Treble” in “Tone Control Settings”
(➔ 52).
Note
• To bypass the bass and treble tone circuits, select the Direct, Pure
Audio (European, Australian and Asian models) or THX lis-
tening mode.
• This procedure can also be performed on the remote controller
by using the Home menu (➔ 24).
En
54
Zone 2
In addition to your main listening room, you can also enjoy playback in the other room, or as we call Zone 2. And, you
can select a different source for each room.
Connecting Zone 2 Connecting Your Zone 2 Speakers to an

Amp in Zone 2
There are two ways you can connect Zone 2 speakers:
This setup allows 7.1-channel playback in your main lis-
1. Connect them directly to the AV receiver.
tening room and 2-channel stereo playback in Zone 2,
2. Connect them to an amp in Zone 2.
with a different source in each room.
Connecting Your Zone 2 Speakers Directly
to the AV receiver Hookup
• Use an RCA audio cable to connect the AV receiver’s
This setup allows 5.1-channel playback in your main room ZONE 2 LINE OUT L/R jacks to an analog audio input on
and 2-channel stereo playback in Zone 2, with a different your Zone 2 amp.
source in each room. This is called Powered Zone 2, as the • Connect your Zone 2 speakers to the speaker terminals on
Zone 2 speakers are powered by the AV receiver. Note that your Zone 2 amp.
when Powered Zone 2 is turned off, you can enjoy 7.1-
channel playback in your main room.
Main room
To use this setup, you must set the “Front High/Front

Wide/Zone2” setting to “Zone2” (➔ 56). TV
Hookup AV receiver
• Connect your Zone 2 speakers to the AV receiver’s FRONT
HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS L/R
terminals.
Main room
TV
Zone 2
AV receiver IN
R L
Receiver/
integrated amp
(North American/
Taiwan models) (Other models)
Note
• The Zone 2 volume must be set on the Zone 2 amp.
R L R L
Zone 2 Zone 2
Note
• With this setup, the Zone 2 volume is controlled by the AV
receiver.
• Powered Zone 2 cannot be used if “Speakers Type” is set to
“Bi-Amp” (➔ 41). En
55
Setting the Powered Zone 2 Using Zone 2
If you’ve connected your Zone 2 speakers to the AV This section explains how to turn Zone 2 on and off, how
receiver, as explained in “Connecting Your Zone 2 Speak- to select an input source for Zone 2, and how to adjust the
ers Directly to the AV receiver” (➔ 55), you must set the volume for Zone 2.
“Front High/Front Wide/Zone2” setting to “Zone2”.
Controlling Zone 2 from the AV receiver
Menu Speaker Setup
1 In the “Speaker Setup” menu, select “Speaker

Settings”, and then press ENTER. ZONE 2 OFF – /+
2 Use q/w to select “Front High/Front Wide/Zone2”

and e/r to select “Zone2”.
`Zone2:
Zone 2 speakers can be used (Powered Zone 2
enabled).
Note
• When “Zone2” is selected and Zone 2 turned on, the Zone 2
speakers connected to the FRONT HIGH OR FRONT WIDE ZONE 2 indicator Input selector buttons
OR ZONE 2 SPEAKERS L/R terminals output sound, but the
1
surround back, front high or front wide speakers connected to the
To turn on Zone 2 and select an input source, press
SURR BACK OR FRONT HIGH OR FRONT WIDE
ZONE 2 followed by an input selector button
SPEAKERS L/R terminals do not. When “Zone2” is selected
and Zone 2 turned off, the surround back, front high or front within 8 seconds.
wide speakers output sound as normal. Zone 2 turns on, the ZONE 2 indicator lights.
• When the “Front High/Front Wide/Zone2” setting is set to
“Zone2” and the input selector of Zone 2 is selected, power con- To select AM or FM, press the TUNER input selec-
sumption on standby mode slightly increases. tor button repeatedly.
• Powered Zone 2 cannot be used if “Speakers Type” is set to (North American models) You can also select SIR-
“Bi-Amp” (➔ 41).
IUS.
To select the same source as that of the main room,

press ZONE 2 repeatedly until “Z2 Selector:
Source” appears on the display.
Note
• You cannot select different AM or FM radio stations for
your main room and Zone 2. The same FM/AM radio sta-
tion will be heard in each room.
2 To turn off Zone 2, press OFF.
Note
• While Powered Zone 2 is being used, listening modes that
require surround back speakers or front high speakers or front
wide speakers (6.1/7.1), such as Dolby Digital EX, DTS-ES,
THX Select2 Cinema, Dolby Pro Logic IIz height, and
Audyssey DSX™ are unavailable.
• When the “Front High/Front Wide/Zone2” setting is set to
“Zone2” and the input selector of Zone 2 is selected, power con-
sumption on standby mode slightly increases.
En
56
Controlling Zone 2 with the Remote Adjusting the Volume for Zone 2
Controller
■ Operating with the remote controller
ON/STANDBY
ZONE2 1 Press ZONE2.
2
Input selector buttons
Use VOL q/w to adjust the volume.
MUTING
■ Operating on the AV receiver
VOLq/w
1 Press ZONE 2 (the ZONE 2 indicator and Zone 2

selector on the display flashes).
2 Use –/+ within 8 seconds to adjust the volume.

1 Press ZONE2 and then press ON/STANDBY.
Zone 2 turns on, the ZONE 2 indicator lights.
If your Zone 2 speakers are connected to a receiver or inte-
2 To select an input source for Zone 2, press
ZONE2, followed by an input selector button.
grated amp in Zone 2, use its volume control to adjust the
volume.
To select AM or FM, press the TUNER input selec-
tor repeatedly. Muting Zone 2
(North American models) You can also select SIR-
IUS. ■ Operating with the remote controller
Note
Press ZONE2 followed by MUTING.
• You cannot select different AM or FM radio stations for
your main room and Zone 2. The same FM/AM radio sta-
tion will be heard in each room. Tip
3 To turn off Zone 2, press ZONE2 followed by ON/

STANDBY.
• To unmute, press ZONE2 followed by MUTING again.
Note
• Only analog input sources are output by the ZONE 2 LINE
Note OUT and FRONT HIGH OR FRONT WIDE OR ZONE 2
SPEAKERS L/R terminals. Digital input sources are not out-
• To control Zone 2, you must press the remote controller’s
put. If no sound is heard when an input source is selected, check
ZONE2 first.
if it’s connected to an analog input.
• While Powered Zone 2 is being used, listening modes that
require surround back speakers or front high speakers or front
wide speakers (6.1/7.1), such as Dolby Digital EX, DTS-ES,
THX Select2 Cinema, Dolby Pro Logic IIz height, and
Audyssey DSX™ are unavailable.
• While Zone 2 is on, u functions will not work.
• You cannot select different AM or FM radio stations for your
main room and Zone 2. The same FM/AM radio station will be
heard in each room. For example, if you have an FM station for
the main room, that station will also be used in Zone 2.
• Zone 2 can also be unmuted by adjusting the volume.
En
57
Controlling iPod
Connecting an Onkyo Dock
B C A
*1
No. Onkyo Dock Cable Note Page

A UP-A1 Dock — • When UP-A1 Dock that seated iPod is (➔ 59)
(Universal Port Option Dock) connected, the power consumption on
standby mode slightly increases.
• You can control your iPod when
“PORT” is selected as the input source.
• See the UP-A1 Dock’s instruction man-
ual for more information.
B ND-S1 Optical digital audio • See the ND-S1’s instruction manual for (➔ 59)
more information.
*1 The ND-S1’s audio outputs are digi-
tal outputs. If the digital audio input
Coaxial digital audio on your AV receiver cannot be
assigned to an input selector whose
Input Display can be set to “DOCK”,
do not connect the u cable, other-
u cable*1 wise a malfunction may occur.
C RI Dock Analog audio (RCA) • See the RI Dock’s instruction manual (➔ 60)
for more information.
*1 To use u (Remote Interactive), you
must make an analog audio connec-
Component video tion (RCA) between the AV receiver
and the RI Dock.
Y
PB/CB
PR/CR
Composite video
u cable*1
Models sold are different depending on the region.

En
58
■ Using Your iPod models Alarm Clock
Using the Onkyo Dock
You can use your iPod models Alarm Clock function to
automatically turn on your iPod and the AV receiver at a
Dock is sold separately. specified time. The AV receiver’s input source will auto-
For the latest information on the Onkyo Dock compo- matically be set to the PORT selector.
nents, see the Onkyo web site at:
Note
http://www.onkyo.com
Before using the Onkyo Dock components, update • To use this function, your iPod must be in the UP-A1 Dock, and
the UP-A1 Dock must be connected to the AV receiver.
your iPod with the latest software, available from the
• This function works only in the Standard mode (➔ 61).
Apple web site.
• When you use this function, be sure to set the AV receiver’s vol-
For supported iPod models, see the instruction man- ume control to a suitable level.
ual of the Onkyo Dock. • When Zone 2 is turned on, you can’t use this function.
• You cannot use this function for sound effects on your iPod.
UP-A1 Dock
■ Charging Your iPod models Battery
With the UP-A1 Dock, you can easily play the music, The UP-A1 Dock charges your iPod models battery while
photo, or movie stored on your Apple iPod through the AV your iPod is in the UP-A1 Dock and connected to the
receiver and enjoy great sound. UNIVERSAL PORT jack on the AV receiver. While your
You can use the AV receiver’s remote controller to operate iPod is seated in the UP-A1 Dock, its battery will be
your iPod. charged when the AV receiver is set to “On” or “Standby”.
■ Basic Operation Note

• When UP-A1 Dock that seated iPod is connected, the power
consumption on standby mode slightly increases.
The AV receiver may take several seconds to startup, so
you might not hear the first few seconds of the first ■ Status Messages
song. • PORT Reading
The AV receiver is checking the connection with the
Auto Power On dock.
If you start iPod playback while the AV receiver is on • PORT Not Support
Standby, the AV receiver will automatically turn on and
The AV receiver do not support the connected dock.
select your iPod as the input source.
• PORT UP-A1
Direct Change
UP-A1 Dock is connected.
If you start iPod playback while listening to another input
source, the AV receiver will automatically select your iPod Note
as the input source. • The AV receiver displays the message “UP-A1” for several sec-
Using the AV receiver’s Remote Controller onds after recognizing the UP-A1.
You can use the AV receiver’s remote controller to control • When the status message is not displayed on the AV receiver’s
basic iPod functions (➔ 60). display, check the connection to your iPod.
ND-S1
■ Operating Notes
• Functionality depends on your iPod model and generation. With the ND-S1 Digital Media Transport, you can easily
• Before selecting a different input source, stop iPod playback play the music stored on your iPod through the AV
to prevent the AV receiver from selecting the iPod input receiver and enjoy great sound.
source by mistake. The ND-S1 processes the digital audio signal directly
• If any accessories are connected to your iPod, the AV receiver from your iPod for high-quality digital audio output (opti-
may not be able to select the input source properly.
cal or coaxial).
• When connecting UP-A1 Dock to the radio tuner UP-HT1
(North American models)/UP-DT1 (European, Australian
Note
and Asian models) with AUTO selected by the tuner’s Mode
Selector switch, you can switch the input source between UP- • You must select “iPod” using ND-S1’s iPod/PC button.
A1 Dock and the tuner, by pressing PORT repeatedly on the • Set the AV receiver’s Input Display to “DOCK” (➔ 25).
front panel.
• While your iPod is in the UP-A1 Dock, its volume control has
no effect. If you adjust your iPod models volume control while
it’s in the UP-A1 Dock, make sure it’s not set too high before
you reconnect your headphones.
• The Auto Power On function will not work if you set your
iPod in the UP-A1 Dock while it is playing.
• When Zone 2 is turned on, you can’t use Auto Power On and
Direct Change functions.
• Do not turn off the power with the iPod still connected to this
unit via the UP-A1 Dock.
• Set your iPod in the UP-A1 Dock after the AV receiver turns
En
on.
59
RI Dock
■ Operating Notes
With the RI Dock, you can easily play the music stored on • Use the AV receiver’s volume control to adjust the playback
your Apple iPod through the AV receiver and enjoy great volume.
sound, and watch iPod slideshows and videos on your TV. • While your iPod is inserted in the ND-S1 or RI Dock, its vol-
In addition, the onscreen display (OSD) allows you to ume control has no effect. If you adjust your iPod models vol-
ume control while it’s in the UP-A1 Dock, make sure it’s not set
view, navigate, and select your iPod’s contents on your
too high before you reconnect your headphones.
TV, and with the supplied remote controller, you can con-
trol your iPod from the comfort of your sofa. You can even
use the AV receiver’s remote controller to operate your Note
iPod. • On the 5th generation iPod and iPod nano, the click wheel is
disabled during playback. For ND-S1, use iPod button to start
Note and stop playback and the remote controller to control other iPod
• Enter the appropriate remote control code before using the AV functions.
receiver’s remote controller for the first time (➔ 63).
• Connect the RI Dock to the AV receiver with an u cable
(➔ 58).
Controlling Your iPod
• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/ By pressing REMOTE MODE that’s been programmed
DOCK”.
with the remote control code for your Dock, you can con-
• Set the AV receiver’s Input Display to “DOCK” (➔ 25).
trol your iPod in the Dock.
■ System Function See “Entering Remote Control Codes” for details on
System On entering a remote control code (➔ 63).
When you turn on the AV receiver, the ND-S1, RI Dock See the Dock’s instruction manual for more information.
and iPod turn on automatically. In addition, when the
■ UP-A1 Dock
ND-S1, RI Dock and iPod are on, the AV receiver can be
turned on by pressing ON/STANDBY. PORT is preprogrammed with the remote control code for
controlling a Dock with Universal Port connector.
Auto Power On
You can control your iPod when “PORT” is selected as
If you press the remote controller’s 1 while the AV
the input source.
receiver is on Standby, the AV receiver will automatically
turn on, select your iPod as the input source, and your
Without the RI Control
iPod will start playback.
Direct Change You must enter a remote control code 82990 first (➔ 63).
If you start iPod playback while listening to another input
■ ND-S1
source, the AV receiver will automatically switch to the
• Select “iPod” using ND-S1’s iPod/PC button.
input to which the ND-S1 and RI Dock is connected.
Using the AV receiver’s Remote Controller ■ RI Dock
You can use the AV receiver’s remote controller to control • Set the RI Dock’s RI MODE switch to “HDD” or
basic iPod functions. “HDD/DOCK”.
Using Your iPod models Alarm Clock • ON/STANDBY may not work with a remote control
If you use the Alarm Clock function on your iPod to start code (without u). In this case, make an u connection
playback, the AV receiver will automatically turn on at the and enter a remote control code 81993 (with u).
specified time and select your iPod as the input source.
Note
With the RI Control
• Linked operations do not work with video playback or when the In this case, make an u connection and enter a remote
alarm is set to play a sound.
• If you use your iPod with any other accessories, iPod playback
control code 81993 (with u).
detection may not work. • Set the AV receiver’s Input Display to “DOCK” (➔ 25).
• This function works only in the Standard mode (➔ 61).
En
60
✔: Available buttons
Press the appropriate REMOTE
MODE first. Onkyo Dock
UP-A1 Dock
u Dock
ND-S1
a f
Buttons
a ON/STANDBY 9 ✔ ✔*1
g b TOP MENU ✔*5 ✔*6
c q/w/e/rENTER ✔ ✔*5 ✔
h
PLAYLIST e/r ✔*3 ✔ ✔
i d 1, 3, 2, 5, 4, ✔ ✔ ✔
7, 6
e REPEAT ✔ ✔ ✔
b j
RANDOM ✔ ✔ ✔
c PLAY MODE ✔*4 ✔*5 ✔*4
k f DISPLAY*7 ✔*2 ✔*5 ✔
g MUTING ✔ ✔*5 ✔
h ALBUM +/– ✔ ✔ ✔
i VOL q/w ✔ ✔*5 ✔
d j MENU ✔*5 ✔
k RETURN ✔
• With some iPod models, generations and RI Docks, certain buttons may not work as expected.
• For detailed operation of the iPod, please refer to the instruction manual of RI Dock.
*1 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Your iPod may not respond the first time you press this
button, in which case you should press it again.
This is because the remote controller transmits the On and Standby commands alternately, so if your iPod is already on, it will
remain on when the remote controller transmits an On command.
Similarly, if your iPod is already off, it will remain off when the remote controller transmits an Off command.
*2 Press DISPLAY to change the following modes:
Standard mode
Nothing is displayed on your TV and you navigate and select your contents by using your iPod models display.
Only this mode can playback the video.
Extended mode (Music)
Playlists (artists, albums, songs, and so on) are displayed on your TV, and you can navigate and select your music while looking at
your TV.
Extended mode (Video)
Playlists (Movies, Music Videos, TV Shows, Video Podcasts, or Rentals) are displayed on your TV, and you can navigate and select
your video while looking at your TV.
*3 In Extended mode (see *2), PLAYLIST is used as the page jump button.
With the page modes, you can quickly locate your favorite songs even when your song lists, artist lists, and so on are very long.
*4 Resume mode
With the Resume function, you can resume playback of the song that was playing when you removed your iPod from the RI Dock or
Standard mode is selected.
*5 Operation can be performed if you connect ND-S1 with an u cable.
*6 TOP MENU works as a Mode button when used with a DS-A2 RI Dock.
*7 DISPLAY turns on backlight for 30 seconds.
Note
• In Extended mode (see *2), the playback will be continued even if the AV receiver is turned off.
• In Extended mode (see *2), you cannot operate your iPod directly.
• In Extended mode (see *2), it may take some time to acquire the contents.
En
61
Controlling Other Components
You can use the AV receiver’s remote controller
(RC-765M) to control your other AV components, includ- 5 Use q/w to select category, and then press
ENTER.
ing those made by other manufacturers. This section
The brand name input panel appears.
explains how to enter the remote control code (with the
default underlined) for a component that you want to con- 8–1. Remote Mode Setup TV
trol: DVD, TV, CD, etc. Category TV
Brand
Preprogrammed Remote Control A B C D E F G H I J K L M
Codes N
1
O
2
P
3
Q R
4 5
S
6
T
7
U
8
V W
9 0
X
–
Y
& @
Z
Space Back Space Search
The following REMOTE MODE are preprogrammed

with remote control codes for controlling the components
listed. You do not need to enter a remote control code to
control these components.
6 Use q/w/e/r to select a character, and then press
ENTER.
For details on controlling these components, see the pages Repeat this step from the 1st character to the 3rd
indicated. character of the brand name.
When you have entered the 3rd character, select
BD/DVD Onkyo Blu-ray Disc player (➔ 64)
“Search” and press ENTER.
TV/CD Onkyo CD player (➔ 64) After searching, a list of the brand name appears.
PORT Onkyo Universal Port Option (➔ 60)
8–1. Remote Mode Setup TV
Category TV
Looking up for Remote Control Code
You can look up for appropriate remote control code from Sonawa
on-screen setup menu. Sonber
Songba
Sonic
Note Soniko
Not Listed
• This setting can be carried out by using On-screen Setup Menu
only.
If the brand name is not found:
Main menu Remote Controller Setup Use r to select “Not Listed”, and then press
1 Press RECEIVER followed by SETUP. ENTER.
The main menu appears onscreen. The brand name input panel appears.
2 Use q/w to select “Remote Controller Setup”, and 7 Use q/w to select brand, and then press ENTER.
then press ENTER. After searching, a remote control code and the input
The “Remote Controller Setup” menu appears. procedure appear. Try it.
8. Remote Controller Setup Remote control code
1. Remote Mode Setup (Number of search results)
8–1. Remote Mode Setup TV

Code 11339
3 Press ENTER. 1. While holding down Remote Mode [TV],

press and hold down [DISPLAY] (3 seconds).
2. Enter the 5-Digit remote control code.
3. Push some key to see if the TV responds.
8–1. Remote Mode Setup 4. Push Remote Mode [RECEIVER].
5. Choose “Works” or “Doesn’t work”.
TV
BD/DVD
VCR/DVR
CBL/SAT Works
GAME Doesn’t work (try next Code)
PC
AUX
TV/CD
8 If you can control component, use q/w to select
4
“Works”, and then press ENTER.
Use q/w to select remote mode, and then press
ENTER. The “Remote Mode Setup” menu appears.
The category selection menu appears.
If you cannot control component, use q/w to select
8–1. Remote Mode Setup TV “Doesn’t work (try next code)” and press ENTER.
TV The next code is appear.
TV/DVD
TV/VCR
En
62
Entering Remote Control Codes 2 Enter the appropriate remote control code for
REMOTE MODE.
You’ll need to enter a code for each component that you • BD/DVD
want to control. `31612:
Onkyo DVD player with u
1 Look up the appropriate remote control code in
the separate Remote Control Codes list.
• TV/CD
`71327:
The codes are organized by category (e.g., DVD
player, TV, etc.). Onkyo CD player with u
`42157:
2 While holding down REMOTE MODE to which
you want to enter a code, press and hold down
Onkyo cassette tape deck with u
DISPLAY (about 3 seconds). • PORT
The remote indicator lights. `81993:
Onkyo Dock
Note See the previous section for how to enter remote
• Remote control codes cannot be entered for RECEIVER control codes.
and ZONE 2.
• Only TV remote control codes can be entered for TV. Note
• Except for RECEIVER, TV and ZONE 2, remote control • When using a cassette tape deck connected via u, press
codes from any category can be entered as REMOTE and hold TV/CD to switch to TAPE.
3
MODE. However, these buttons also work as input selec-
Press REMOTE MODE, point the remote control-
tor buttons (➔ 23), so choose a REMOTE MODE that
corresponds with the input to which you connect your ler at the AV receiver, and operate the component.
component. For example, if you connect your CD player
to the CD input, choose TV/CD when entering its remote If you want to control an Onkyo component by pointing
control code. the remote controller directly at it, or you want to control
3 Within 30 seconds, use the number buttons to

enter the 5-digit remote control code.
an Onkyo component that’s not connected via u, use the
following remote control codes:
The remote indicator flashes twice. • BD/DVD
If the remote control code is not entered success- ` 30627:
fully, the remote indicator will flash once slowly. Onkyo DVD player without u
• TV/CD
Note ` 71817:
• The remote control codes provided are correct at the time of
Onkyo CD player without u
printing, but are subject to change. ` 11807:
Onkyo TV
If you want to control an Onkyo component by pointing the
Remote Control Codes for Onkyo remote controller directly at it, use the following remote
Components Connected via u control codes:
` 32900:
Onkyo components that are connected via u are con- Onkyo Blu-ray Disc player
trolled by pointing the remote controller at the AV
` 32901:
receiver, not the component. This allows you to control
Onkyo HD-DVD player
components that are out of view, in a rack, for example.
` 70868:
1
Onkyo MD recorder
Make sure the Onkyo component is connected
` 71323:
with an u cable and an analog audio cable
Onkyo CD recorder
(RCA).
` 82990:
See “Connecting Onkyo u Components” for
Onkyo Dock
details (➔ 20).
Note
• If you connect a cassette tape deck to the TV/CD IN jack, or
connect an RI Dock to the to the TV/CD IN or VCR/DVR IN or
GAME IN jacks, for u to work properly, you must set the Input
Display accordingly (➔ 25).
En
63
Resetting REMOTE MODE Buttons Controlling Other Components
You can reset a REMOTE MODE to its default remote By pressing REMOTE MODE that’s been programmed
control code. with the remote control code for your component, you can
control your component as below.
1 While holding down REMOTE MODE that you
want to reset, press and hold down HOME until
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
the remote indicator lights (about 3 seconds). (➔ 63).
2 Within 30 seconds, press REMOTE MODE again.
Controlling a TV
The remote indicator flashes twice, indicating that
the button has been reset. TV is preprogrammed with the remote control code for
Each of REMOTE MODE is preprogrammed with a controlling a TV that supports the p*1 (limited to
remote control code. When a button is reset, its pre- some models). The TV must be able to receive remote
programmed code is restored.
control commands via p and be connected to the
AV receiver via HDMI. If controlling your TV via
Resetting the Remote Controller p doesn’t work very well, program your TV’s
remote control code into TV and use the TV remote mode
You can reset the remote controller to its default settings. to control your TV.
1 While holding down RECEIVER, press and hold

down HOME until the remote indicator lights
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
(about 3 seconds).
2 Within 30 seconds, press RECEIVER again. BD/DVD is preprogrammed with the remote control code
for controlling a component that supports the p*1
The remote indicator flashes twice, indicating that
the remote controller has been reset. (limited to some models). The component must be able to
receive remote control commands via p and be
connected to the AV receiver via HDMI.
*1 The p supported by the AV receiver is the CEC

system control function of the HDMI standard.
En
64
✔: Available buttons
Press the appropriate REMOTE
MODE first. Components
DVD player/DVD recorder
CD player/CD recorder
Cassette tape deck

Blu-ray Disc player
Satellite receiver
HD DVD player
Cable receiver
a i
MD recorder
VCR/PVR
TV
Buttons
j a ON/STANDBY ✔ ✔ ✔ ✔ ✔ ✔
9
k b 9, INPUT, ✔
TV VOL q/w
b ✔ ✔ ✔
c GUIDE
TOP MENU ✔
d q/w/e/r ✔ ✔ ✔ ✔ ✔
c l ENTER
e SETUP ✔ ✔ ✔ ✔ ✔
d f 1, 3, 2, 5, ✔*1 ✔ ✔ ✔ ✔ ✔*3
4, 7, 6
e m g SEARCH ✔*1*2 ✔*1 ✔*2 ✔*2 ✔
REPEAT ✔*1*2 ✔ ✔*2 ✔*2 ✔
n RANDOM ✔*1*2 ✔*1 ✔*2 ✔*2 ✔
PLAY MODE ✔*1*2 ✔*1 ✔*2 ✔*2 ✔
h Number: 1 to 9, 0 ✔ ✔ ✔ ✔ ✔
f Number: +10 ✔*1 ✔*1 ✔ ✔ ✔
i DISPLAY ✔ ✔ ✔ ✔ ✔
j MUTING ✔ ✔ ✔ ✔ ✔ ✔
g k CH +/– ✔ ✔ ✔ ✔
DISC +/– ✔ ✔
l PREV CH ✔ ✔ ✔
MENU ✔
h m RETURN ✔ ✔ ✔ ✔
n AUDIO ✔*1 ✔*1 ✔
o CLR ✔ ✔ ✔ ✔ ✔
o
*1 The p function is not supported. The p sup-
ported by the AV receiver is the CEC system control function
of the HDMI standard.
*2 These buttons function as colored buttons or A, B, C, D but-
tons.
*3 3 (Pause) functions as reverse playback.
Note
• See the “Controlling Your iPod” about the operation of iPod
(➔ 60).
Note
• With some components, certain buttons may not work as
expected, and some may not work at all.
En
65
Troubleshooting
If you have any trouble using the AV receiver, look for a ■ The STANDBY indicator flashes red
solution in this section. If you can’t resolve the issue your- The protection circuit has been activated. Remove —
self, contact your Onkyo dealer. the power cord from the wall outlet immediately.
Disconnect all speaker cables and input sources, and
leave the AV receiver with its power cord discon-
If you can’t resolve the issue yourself, try resetting the
nected for 1 hour. After that, reconnect the power
AV receiver before contacting your Onkyo dealer. cord and set the volume to maximum. If the AV
To reset the AV receiver to its factory defaults, turn it receiver stays on, set the volume to minimum, dis-
on and, while holding down VCR/DVR, press ON/ connect the power cord, and reconnect your speakers
STANDBY. “Clear” will appear on the display and and input sources. If the AV receiver turns off when
the AV receiver will enter Standby mode. you set the volume to maximum, disconnect the
power cord, and contact your Onkyo dealer.
Audio
■ There’s no sound, or it’s very quiet
Note that resetting the AV receiver will delete your Make sure that the digital input source is selected 40
radio presets and custom settings. properly.
Make sure that all audio connecting plugs are pushed 16
in all the way.
Make sure that the inputs and outputs of all compo- 17-20
Remote indicator nents are connected properly.
Make sure that the polarity of the speaker cables is 13
correct, and that the bare wires are in contact with
the metal part of each speaker terminal.
Make sure that the input source is properly selected. 23
RECEIVER Make sure that the speaker cables are not shorting. 13
Check the volume. The AV receiver is designed for —
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
HOME If the MUTING indicator is flashing on the display, 24
press the remote controller’s MUTING to unmute
the AV receiver.
To reset the remote controller to its factory defaults, While a pair of headphones is connected to the 25
while holding down RECEIVER, press and hold down PHONES jack, no sound is output by the speakers.
HOME until the remote indicator lights (about 3 sec- If there’s no sound from a DVD player connected to —
onds). Within 30 seconds, press RECEIVER an HDMI IN, check the DVD player’s output set-
tings, and be sure to select a supported audio format.
again.
Check the digital audio output setting on the con- —
nected device. On some game consoles, such as
The on-screen setup menus appear only on a TV that those that support DVD, the default setting is off.
is connected to the HDMI OUT. If your TV is con- With some DVD-Video discs, you need to select an —
nected to the MONITOR OUT V or the COMPO- audio output format from a menu.
NENT VIDEO OUT, use the AV receiver’s display If your turntable uses an MC cartridge, you must —
when changing settings. connect an MC head amp, or an MC transformer.
Make sure that none of the connecting cables are —
bent, twisted, or damaged.
Power Not all listening modes use all speakers. 33
■ Can’t turn on the AV receiver Specify the speaker distances and adjust the individ- 42
ual speaker levels.
Make sure that the power cord is properly plugged —
Make sure that the speaker setup microphone is not —
into the wall outlet.
still connected.
Unplug the power cord from the wall outlet, wait five —
The input signal format is set to PCM or DTS. Set it 54
seconds or more, then plug it in again.
to Auto.
En
66
■ Only the front speakers produce sound With some DVD-Video discs, you need to select an —
When the Stereo or Mono listening mode is selected, — audio output format from a menu.
only the front speakers and subwoofer produce Depending on the input signal, some listening modes 33–37
sound. cannot be selected.
In the Mono listening mode, only the front speakers 44
output sound if the “Output Speaker” setting is set ■ Can’t select the Pure Audio listening mode
to “Left/Right”.
(European, Australian and Asian models) The —
Check the Speaker Configuration. 41 Pure Audio listening mode cannot be selected while
Zone 2 is on.
■ Only the center speaker produces sound
If you use the Dolby Pro Logic IIx Movie, Dolby Pro — ■ Can’t get 6.1/7.1 playback
Logic IIx Music, or Dolby Pro Logic IIx Game lis- If no surround back speakers, front wide and front —
tening mode with a mono source, such as an AM high speakers are connected, or the Zone 2 speakers
radio station or mono TV program, the sound is con- are being used, 6.1/7.1 playback is not possible.
centrated in the center speaker.
You can not always select all of the listening modes, 33–37
In the Mono listening mode, only the front speakers 44 depending on the number of the speakers connected.
output sound if the “Output Speaker” setting is set
to “Center”.
■ The speaker volume cannot be set as required
Make sure the speakers are configured correctly. 41
(The volume cannot be set to +18.0 dB)
■ The surround speakers produce no sound Check to see if a maximum volume has been set. 50
If the volume level of each individual speaker has 25, 42
When the T-D (Theater-Dimensional), Stereo or — been adjusted to high positive values, then the maxi-
Mono listening mode is selected, the surround
mum master volume possible may be reduced. Note
speakers produce no sound.
that the individual speaker volume levels are set
Depending on the source and current listening mode, — automatically after the Audyssey 2EQ® Room Cor-
not much sound may be produced by the surround rection and Speaker Setup function has been com-
speakers. Try selecting another listening mode. pleted.
Make sure the speakers are configured correctly. 41
■ Noise can be heard
■ The center speaker produces no sound
Using cable ties to bundle audio cables with power —
When the Stereo or Mono listening mode is selected, — cords, speaker cables, and so on may degrade the
the center speaker produces no sound. audio performance, so don’t do it.
In the Mono listening mode, only the front speakers 44 An audio cable may be picking up interference. Try —
output sound if the “Output Speaker” setting is set repositioning your cables.
to “Left/Right”.
Make sure the speakers are configured correctly. 41 ■ The Late Night function doesn’t work
Make sure the source material is Dolby Digital, 53
■ The front high, front wide and surround back Dolby Digital Plus, and Dolby TrueHD.
speakers produce no sound
Depending on the current listening mode, no sound 33 ■ About DTS signals
may be produced by the front high, front wide and When DTS program material ends and the DTS bit- —
surround back speakers. Select another listening stream stops, the AV receiver remains in DTS listen-
mode. ing mode and the DTS indicator remains on. This is
Not much sound may be produced by the front high, — to prevent noise when you use the pause, fast for-
front wide and surround back speakers with some ward, or fast reverse function on your player. If you
sources. switch your player from DTS to PCM, because the
Make sure the speakers are configured correctly. 41 AV receiver does not switch formats immediately,
While Powered Zone 2 is being used, playback in the 55 you may not hear any sound, in which case you
main room is reduced to 5.1-channels and the front should stop your player for about three seconds, and
high, front wide and surround back speakers produce then resume playback.
no sound. With some CD and LD players, you won’t be able to —
playback DTS material properly even though your
player is connected to a digital input on the AV
■ The subwoofer produces no sound
receiver. This is usually because the DTS bitstream
When you play source material that contains no — has been processed (e.g., output level, sampling rate,
information in the LFE channel, the subwoofer pro- or frequency response changed) and the AV receiver
duces no sound. doesn’t recognize it as a genuine DTS signal. In such
Make sure the speakers are configured correctly. 41 cases, you may hear noise.
When playing DTS program material, using the —
■ There’s no sound with a certain signal format pause, fast forward, or fast reverse function on your
player may produce a short audible noise. This is not
Check the digital audio output setting on the con- — a malfunction.
nected device. On some game consoles, such as
those that support DVD, the default setting is off. En
67
■ The beginning of audio received by an HDMI IN ■ The on screen display does not appear
can’t be heard Depending on the input signal, the on screen display 50
Since it takes longer to identify the format of an — may not appear when the input signal from the
HDMI signal than it does for other digital audio sig- HDMI IN is output to a device connected to the
nals, audio output may not start immediately. HDMI OUT.
Video Tuner
■ There’s no picture ■ Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t light
Make sure that all video connecting plugs are pushed 16
in all the way. Relocate your antenna. —
Make sure that each video component is properly 17, 18, Move the AV receiver away from your TV or com- —
connected. 58 puter.
If your TV is connected to the HDMI OUT, select 39 Listen to the station in mono. 28
“- - - - -” in the “HDMI Input” setup to watch com- When listening to an AM station, operating the —
posite video, and component video sources. remote controller may cause noise.
If the video source is connected to a component 18, 39 Passing cars and airplanes can cause interference. —
video input, you must assign that input to an input
Concrete walls weaken radio signals. —
selector, and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI- If nothing improves the reception, install an outdoor —
TOR OUT. antenna.
If the video source is connected to a composite video 18
input, your TV must be connected to the HDMI Remote Controller
OUT or the corresponding composite video output.
If the video source is connected to an HDMI input, 17, 39 ■ The remote controller doesn’t work
you must assign that input to an input selector, and
Before operating this unit, be sure to press —
your TV must be connected to the HDMI OUT.
RECEIVER.
While the Pure Audio listening mode is selected, the —
video circuitry is turned off and only video signals Make sure that the batteries are installed with the 4
correct polarity.
input through HDMI IN can be output.
Install new batteries. Don’t mix different types of 4
On your TV, make sure that the video input to which —
batteries, or old and new batteries.
the AV receiver is connected is selected.
Make sure that the remote controller is not too far 4
away from the AV receiver, and that there’s no
■ There’s no picture from a source connected to
obstruction between the remote controller and the
an HDMI IN AV receiver’s remote control sensor.
Reliable operation with an HDMI-to-DVI adapter is 73 Make sure that the AV receiver is not subjected to —
not guaranteed. In addition, video signals from a PC direct sunshine or inverter-type fluorescent lights.
are not guaranteed. Relocate if necessary.
When the Resolution is set to any resolution not sup- 39 If the AV receiver is installed in a rack or cabinet —
ported by the TV, no video is output by the HDMI with colored-glass doors, the remote controller may
outputs. not work reliably when the doors are closed.
If the message Resolution Error appears on the AV — Make sure you’ve selected the correct remote con- 11, 64
receiver’s display, this indicates that your TV does troller mode.
not support the current video resolution and you When using the remote controller to control other —
need to select another resolution on your DVD manufacturers’ AV components, some buttons may
player. not work as expected.
Make sure you’ve entered the correct remote control 63
■ The on-screen menus don’t appear code.
(European, Australian and Asian models) Specify 50 Make sure to set the same ID on both the AV receiver 50
the TV system used in your area in the TV Format and remote controller.
Setup.
On your TV, make sure that the video input to which — ■ Can’t control other components
the AV receiver is connected is selected.
If it’s an Onkyo component, make sure that the u 20
When the AV receiver doesn’t connect TV with —
cable and analog audio cable are connected properly.
HDMI, onscreen menus are not displayed.
Connecting only an u cable won’t work.
Make sure you’ve selected the correct remote con- 11, 64
■ The picture is distorted
troller mode.
(European, Australian and Asian models) Specify 50 If you’ve connected a cassette tape deck, to the TV/ 25
the TV system used in your area in the TV Format. CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN or VCR/DVR IN jacks, for the remote
controller to work properly, you must set the display.
If you cannot operate it, you will need to enter the 62
En appropriate remote control code.
68
To control another manufacturer’s component, point 63 ■ The AV receiver unexpectedly selects your iPod
the remote controller at that component. as the input source
To control an Onkyo component that’s connected via 63 Always pause iPod playback before selecting a dif- —
u, point the remote controller at the AV receiver. ferent input source. If playback is not paused, the
Be sure to enter the appropriate remote control code Direct Change function may select your iPod as the
first. input source by mistake during the transition
To control an Onkyo component that’s not connected 63 between tracks.
via u, point the remote controller at the compo-
nent. Be sure to enter the appropriate remote control
code first.
Recording
The entered remote control code may not be correct. — ■ Can’t record
If more than one code is listed, try each one.
On your recorder, make sure the correct input is —
selected.
UP-A1 Dock for iPod To prevent signal loops and damage to the AV —
receiver, input signals are not fed through to outputs
■ There’s no sound with the same name (VCR/DVR IN to VCR/DVR
Make sure your iPod is actually playing. — OUT).
Make sure your iPod is inserted properly in the — When the Pure Audio listening mode is selected, —
Dock. recording is not possible because no video signals
are output. Select another listening mode.
Make sure the UP-A1 Dock is connected to the UNI- —
VERSAL PORT jack on the AV receiver.
Make sure the AV receiver is turned on, the correct — Zone 2
input source is selected, and the volume is turned up.
Make sure the plugs are pushed in all the way. — ■ There’s no sound
Try resetting your iPod. — Only components connected to analog inputs can be —
played in Zone 2.
■ There’s no video
■ The Zone 2 speakers produce no sound
Make sure that your iPod’s TV OUT setting is set to —
On. Powered Zone 2 cannot be used if “Speakers Type” 41
Make sure the correct input is selected on your TV or — is set to “Bi-Amp”.
the AV receiver. To use the Zone 2 speakers, you must set the “Front 56
Some versions of the iPod do not output video. — High/Front Wide/Zone2” setting to “Zone2”.
■ The AV receiver’s remote controller doesn’t Others

control your iPod
■ The sound changes when I connect my
Make sure your iPod is properly inserted in the —
Dock. If your iPod is in a case, it may not connect headphones
properly to the Dock. Always remove your iPod When a pair of headphones is connected, the listen- —
from the case before inserting it into the Dock. ing mode is set to Stereo, unless it’s already set to
The iPod cannot be operated while it’s displaying the — Stereo, Mono, Direct, or Pure Audio. (Pure Audio
Apple logo. listening mode is not available for North American
Make sure you’ve selected the right remote mode. — models.)
When you use the AV receiver’s remote controller, —
point it toward your AV receiver. ■ The speaker distance cannot be set as required
When connecting UP-A1 Dock to the radio tuner — In some cases, corrected values suitable for home —
UP-HT1 (North American models)/UP-DT1 theater use may be set automatically.
(European, Australian and Asian models) with
AUTO selected by the tuner’s Mode Selector switch, ■ The display doesn’t work
you can switch the input source between UP-A1
Dock and the tuner, by pressing PORT repeatedly The display is turned off when the Pure Audio listen- —
on the front panel. ing mode is selected.
If you still can’t control your iPod, start playback by —
pressing your iPod’s Play button. Remote operation ■ How do I change the language of a multiplex
should then be possible. source
Try resetting your iPod. —
Use the “Multiplex” setting on the “Audio Adjust” 44
Depending on your iPod, some buttons may not — menu to select “Main” or “Sub”.
work as expected.
■ The u functions don’t work
To use u, you must make an u connection and an 20
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected dig-
itally. En
69
■ The functions System On/Auto Power On and
Important Note Regarding Video Playback
Direct Change don’t work for components
connected via u The AV receiver can upconvert component video and
These functions don’t work when Zone 2 is turned 20 composite video sources for display on a TV connected to
on. the HDMI OUT. However, if the picture quality of the
source is poor, upconversion may make the picture worse
■ When performing “Audyssey 2EQ® Room or disappear altogether.
Correction and Speaker Setup”, the In this case, try the following:
measurement fails showing the message
“Ambient noise is too high.”. 1 If the video source is connected to a component
video input, connect your TV to the COMPO-
This can be caused by any malfunction in your —
speaker unit. Check if the unit produces normal NENT VIDEO OUT.
sounds. If the video source is connected to a composite video
input, connect your TV to the MONITOR OUT V.
■ The following settings can be made for the
composite video inputs 2 On the main menu, select “1. Input/Output
Assign”, and then select “2. HDMI Input”.
You must use the buttons on the unit to make these set- Select the relevant input selector, and assign it to
tings. “- - - - -” (➔ 39).
3
1. While holding down the input selector button for the input
source that you want to set, press SETUP.
On the main menu, select “1. Input/Output
2. Use e/r to change the setting. Assign”, and then select “3. Component Video
3. Press the input selector button for the input source that you Input” (➔ 40):
want to set when you’ve finished.
If the video source is connected to COMPONENT
• Video Attenuation VIDEO IN 1, select the relevant input selector, and
This setting can be made for the BD/DVD, VCR/DVR, assign it to “IN1”.
CBL/SAT, GAME, or AUX input.
If you have a games console connected to the composite If the video source is connected to COMPONENT
video input, and the picture isn’t very clear, you can VIDEO IN 2, select the relevant input selector, and
attenuate the gain. assign it to “IN2”.
Video ATT:OFF: (default). If the video source is connected to composite video
Video ATT:ON: Gain is reduced by 2 dB. input, select the relevant input selector, and assign it
to “- - - - -”.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.
En
70
Specifications
Amplifier Section General
Rated Output Power Power Supply (North American and Taiwan)

All channels: (North American) AC 120 V, 60 Hz
100 watts minimum continuous power (European) AC 230 V, 50 Hz
per channel, 8 ohm loads, 2 channels (Others) AC 220 - 240 V, 50/60 Hz
driven from 20 Hz to 20 kHz, with a Power Consumption (North American) 6.3 A
maximum total harmonic distortion of (Others) 620 W
0.08% (FTC)
125 watts minimum continuous power Stand-by Power Consumption
per channel, 6 ohm loads, 2 channels (North American and Taiwan) 0.2 W
driven at 1 kHz, with a maximum total (Others) 0.3 W
harmonic distortion of 0.1% (FTC) Dimensions 435 mm × 176 mm × 329 mm
115 watts minimum continuous power (W × H × D) 17-1/8" × 6-15/16" × 12-15/16"
per channel, 8 ohm loads, 2 channels
driven at 1 kHz, with a maximum total Weight 11.5 kg (25.4 lbs.)
harmonic distortion of 0.7% (FTC)
(Others) ■ HDMI
7 ch × 160 W at 6 ohms, 1 kHz, 1 ch driven
(IEC) Input IN 1, IN 2, IN 3, IN 4, IN 5, AUX INPUT
Maximum Effective Output Power Output OUT
(Asian) Video Resolution 1080p
7 ch × 175 W at 6 ohms, 1 kHz, 1 ch driven
Audio Format Dolby TrueHD, DTS Master Audio,
(JEITA) DVD-Audio, DSD
Dynamic Power 240 W (3 Ω, Front) Supported 3D, Audio Return Channel, Deep Color,
210 W (4 Ω, Front) x.v.Color, LipSync, CEC
120 W (8 Ω, Front)
THD (Total Harmonic Distortion)
■ Video Inputs
(North American and Taiwan)
0.08% (Power Rated)
(Others) Component IN 1, IN 2
0.08% (1 kHz, 1 W) Composite BD/DVD, VCR/DVR, CBL/SAT, GAME,
Damping Factor 60 (Front, 1 kHz, 8 Ω) AUX
Input Sensitivity and Impedance Analog RGB input PC IN
200 mV/47 kΩ (LINE)
■ Video Outputs
Output Level and Impedance
200 mV/2.2 kΩ (REC OUT) Component OUT
Frequency Response 5 Hz - 100 kHz/+1 dB, -3 dB (DSP bypass) Composite MONITOR OUT, VCR/DVR OUT
Tone Control Characteristics
±10 dB, 50 Hz (BASS) ■ Audio Inputs
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio 106 dB (LINE, IHF-A) Digital Optical: 2
Speaker Impedance (North American and Taiwan) 6 Ω - 16 Ω Coaxial: 2
(Others) 4 Ω - 16 Ω Analog BD/DVD, VCR/DVR, CBL/SAT, GAME,
PC, TV/CD, AUX
Video Section
■ Audio Outputs
Input Sensitivity/Output Level and Impedance
Analog VCR/DVR, ZONE2 Line Out
1 Vp-p/75 Ω (Component Y)
Subwoofer Pre Outputs
0.7 Vp-p/75 Ω (Component PB/CB, PR/CR)
1 Vp-p/75 Ω (Composite) 2
Component Video Frequency Response Speaker Outputs Main (L, R, C, SL, SR, SBL, SBR, FHL,
FHR) + ZONE2 / Front Wide (L, R)
5 Hz - 100 MHz/+0 dB, -3 dB
Phones 1 (6.3 ø)
Tuner Section
■ Others
FM Tuning Frequency Range MIC 1

(North American) 87.5 MHz - 107.9 MHz Universal Port 1
(European) 87.50 MHz - 108.00 MHz, RI 1
RDS
(Taiwan) 87.5 MHz - 108.0 MHz
(Others) 87.5 MHz - 108.0 MHz, RDS Specifications and features are subject to change
AM Tuning Frequency Range without notice.
(North American) 530 kHz - 1710 kHz
(Others) 522/530 kHz - 1611/1710 kHz
Preset Channel 40
Digital Tuner (North American models)
En
SIRIUS
71
About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital
interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video compo-
nents. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a
single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichan-
nel digital audio, and multichannel PCM).
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays with
a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays,
resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can
display the picture.
The AV receiver’s HDMI interface is based on the following:

Audio Return Channel, 3D, x.v.Color, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution
Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM
Supported Audio Formats

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD
Master Audio)
Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.
About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital
video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.
*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999.
*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s
designed to protect video content and requires a HDCP-compatible device to display the encrypted video.
*3 DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this
open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance
PCs and digital displays.
Note
• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by
using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for
audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.
• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or
there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for
details.
En
72
Using an RIHD-compatible TV, Player, or Recorder
p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo
components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over
HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, opera-
tion with components other than p-compatible components cannot be guaranteed.
■ About p-compatible components ■ Operations that can be performed with p

The following components are p-compatible. (As connection
of February 2010) See the Onkyo web site for latest infor- For p-compatible TV
mation. The following linked operation is possible by connecting
TV the AV receiver to an p-compatible TV.
• Panasonic VIERA Link compatible TV • The AV receiver will enter Standby mode when the
• Toshiba REGZA-LINK compatible TV power of the TV is turned to Standby.
• Sharp TV (See Onkyo web site for latest information on • You can set on the menu screen of the TV to either out-
compatible models.) put the audio from the speakers connected to the AV
Players/Recorders receiver, or from the speakers of the TV.
• Onkyo and Integra p-compatible players • It is possible to output the video/audio from the antenna
• Panasonic VIERA Link compatible players and record- or from the input jack of the TV from the speakers con-
ers (only when used together with Panasonic VIERA nected to the AV receiver. (A connection such as optical
Link compatible TV) digital cable or similar is required above the HDMI
• Toshiba REGZA-LINK compatible players and record- cable.)
ers (only when used together with Toshiba REGZA- • Input to the AV receiver can be selected with the remote
LINK compatible TV) controller of the TV.
• Sharp players and recorders (only when used together • Operations such as volume adjustment or similar for the
with Sharp TV) AV receiver can be performed from the remote controller
of the TV.
* Models other than those mentioned above may have some For p-compatible players/recorders
interoperability if compatible with CEC which is part of the The following link operation is possible by connecting the
HDMI Standard, but operation cannot be guaranteed. AV receiver to an p-compatible player/recorder.
Note • When the playback is started on the player/recorder,
• Do not connect the p-compatible component more than input of the AV receiver will switch to the HDMI input
the following number to the HDMI input terminal so that the of the player/recorder that is playing back.
linked operations work properly. • Operation of the player/recorder is possible with the
–Blu-ray Disc/DVD player is up to three. remote controller supplied with the AV receiver.
–Blu-ray Disc recorder/DVD recorder/Digital Video Recorder is
up to three. * Not all functions may operate depending on the model.
–Cable/Satellite Set-top box is up to four.
• Do not connect the AV receiver to the other AV receiver/AV
amplifier via HDMI.
• When the p-compatible component more than the
above-mentioned is connected, the linked operations are not
guaranteed.
En
73
■ How to connect and setup
3 Confirm the settings.
1
1. Turn on the power for all connected components.
Confirm the connecting and setting.
2. Turn off the power of the TV, and confirm that
1. Connect the HDMI OUT jack to the HDMI input
the power of the connected components is turned
jack of the TV.
off automatically with the link operation.
Blu-ray Disc/DVD player, etc. 3. Turn on the power of the Blu-ray Disc/DVD
player/recorder.
4. Start playback of the Blu-ray Disc/DVD player/
HDMI recorder, and confirm the following.
connection • The power of the AV receiver is turned on
automatically, and input with the Blu-ray
AV receiver Disc/DVD player/recorder connected is
selected.
DIGITAL AUDIO HDMI • The power of the TV is turned on automati-
connection connection cally, and input with the AV receiver con-
(OPTICAL) nected is selected.
5. Following the operating instructions of the TV,
select “Use the TV speakers” from the menu
TV, projector, etc. screen of the TV, and confirm that the audio is
2. Connect the audio output from the TV to the output from the speakers of the TV, and not from
OPTICAL IN 2 jack of the AV receiver using an the speakers connected to the AV receiver.
optical digital cable. 6. Select “Use the speakers connected from the AV
receiver” from the menu screen of the TV, and
Note
confirm that the audio is output from the speak-
• When the audio return channel (ARC) function is used
ers connected to the AV receiver, and not from
with TV for HDMI 1.4, it should not be this connection
(➔ 52). the TV speakers.
3. Connect the HDMI output of the Blu-ray Disc/ Note
DVD player/recorder to the HDMI IN 1 jack of • Perform the above operations when you initially use the
the AV receiver. AV receiver, when the settings of each component are
changed, when the main power of each component is
Note
turned off, when the power cable is disconnected from the
• It is necessary to assign the HDMI input when connecting power supply, or when there has been a power outage.
the Blu-ray Disc/DVD player/recorder to other jacks
(➔ 39). Do not assign the components connected to the 4 Operate with the remote controller.
HDMI IN to the TV/CD input at this time. Appropriate For buttons that can be operated (➔ 64).
CEC (Consumer Electronics Control) operation can not be
Note
guaranteed.
• Audio from DVD-Audio or Super Audio CD may not out-
2 Change each item in the “HDMI Setup” as below: put from the TV speakers. You will be able to output the
• HDMI Control (RIHD): On audio from the TV speakers by setting the audio output of
• Audio Return Channel (ARC): Auto the DVD player to 2ch PCM. (It may not be possible
• Power Control: On depending on the player models.)
• Even if you set to output audio on the TV speakers, audio
• TV Control: On
will be output from the speakers connected to the AV
receiver when you adjust the volume or switch the input
See for details of each setting (➔ 51, 52). on the AV receiver. To output audio from the TV speakers,
re-do the operations on the TV.
• Do not connect the u cable when connecting to the u
and u audio control compatible components.
• When you select anything other than the HDMI jack
where the AV receiver is connected as the input on the TV,
input on the AV receiver will be switched to “TV/CD”.
• The AV receiver will automatically power on in conjunc-
tion when it determines it to be necessary. Even if the AV
receiver is connected to an p compatible TV or
player/recorder, it will not power on if it is not necessary.
It may not power on in conjunction when the TV is set to
output audio from the TV.
• Linked functions with the AV receiver may not work
depending on the model. Operate the AV receiver directly
in such cases.
En
74
Video Resolution Chart
The following tables show how video signals at different resolutions are output by the AV receiver.
NTSC/PAL
✔: Output
Output HDMI COMPONENT COMPOSITE

1080p 1080i 720p 480p/ 480i/ 1080p 1080i 720p 480p/ 480i/ 480i/576i
Input 576p 576i 576p 576i
HDMI 1080p ✔
1080i ✔ ✔ ✔
720p ✔ ✔ ✔
480p/576p ✔ ✔ ✔ ✔
480i/576i ✔ ✔ ✔ ✔ ✔
COMPONENT 1080p ✔ ✔
1080i ✔ ✔ ✔ ✔
720p ✔ ✔ ✔ ✔
480p/576p ✔ ✔ ✔ ✔ ✔
480i/576i ✔ ✔ ✔ ✔ ✔ ✔
COMPOSITE 480i/576i ✔ ✔ ✔ ✔ ✔ ✔
PC (D-Sub)*1 ✔ ✔ ✔ ✔
*1 Available resolution:
[640 × 480 60/67/73/75 Hz], [800 × 600 56/60/72/75 Hz], [1024 × 768 60/70/75 Hz], [1152 × 864 75 Hz], [1152 × 870 75 Hz],
[1280 × 720 60/75 Hz], [1280 × 768 60 Hz], [1280 × 960 60/75 Hz], [1280 × 1024 60/70/75 Hz], [1360 × 768 60 Hz],
[1400 × 1050 60 Hz], [1600 × 1200 60 Hz], [1680 × 1050 60 Hz], [1920 × 1080 60 Hz]
En
75
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
ONKYO CHINA LIMITED
Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung,
N.T., Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
Y1002-1
SN 29400239
(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 4 0 0 2 3 9 *

Manual Onkyo TX-SR608

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Onkyo TX-SR608

Uploaded by

Copyright:

Available Formats

Contents

AV Receiver Introduction ...................................2

Turning On & Basic Operations ......22

Instruction Manual Advanced Operations .................38

Controlling iPod & Other

Thank you for purchasing an Onkyo AV Receiver.

Important Safety Instructions

Declaration of Conformity Aiming the Remote Controller

SIRIUS, XM and all related marks and logos are trademarks

THX Select2 Plus

a ON/STANDBY button (➔ 22) n TUNING, PRESET (➔ 28 to 29), arrow and

For detailed information, see the pages in parentheses.

e FM ANTENNA jack and AM ANTENNA terminal m ZONE 2 LINE OUT jacks

f MONITOR OUT V jack n SUBWOOFER PRE OUT jacks

g UNIVERSAL PORT jack o FRONT HIGH OR FRONT WIDE OR ZONE 2

To control the AV receiver, press RECEIVER to select

i For detailed information, see the pages in parentheses.

f ■ Controlling the tuner

*1 VIDEO functions as a short cut of HOME.

The supplied speaker cable labels are also color-coded and

Connecting the Speaker Cables

Using Banana Plugs (North American models)

Push-type speaker terminals

North American and Taiwan models Surround Surround Surround Surround

European, Australian and Asian models

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s

jack to an input on the amp.

Bi-amping the Front Speakers

The FRONT L/R and SURR BACK OR FRONT

HDMI cable : Video & Audio Other cables : Video

Blu-ray Disc/ Blu-ray Disc/

Signal Cable Jack Description

Composite video Composite video is commonly used on TVs, VCRs, and

1/8" (3.5 mm) This cable carries analog audio.

VCR or DVD recorder/Digital Video Recorder

Satellite, cable, set-top box, etc.

Jack Signal Components Assignable

■ Audio return channel (ARC) function

No. Jack Signal Components Assignable

■ System On/Auto Power On L

When you start playback on a component connected via R

ponent as the input source. L

When playback is started on a component connected via

■ Remote Control e.g., CD player

You can use the AV receiver’s remote controller to con-

the appropriate remote control code first (➔ 63).

Insert the plug fully Insert the plug fully

Video Connection Formats

video input is assigned to the input selector, that component IN

Audio Connection Formats

Front panel Remote controller

Press RECEIVER followed by DISPLAY repeat-

Playing the Connected Component Signal format*2

1 Use the input selector buttons to select the input

2 Start playback on the source component.

1 Press RECEIVER followed by INPUT SELEC-

For the VCR/DVR input selector, the setting

2EQ: Auto Setup

Speaker Terminal Assign

If your front speakers are bi-amped, you must select

6 When prompted, repeat step 5.

1 On the remote controller, press TUNER repeat-