Instruction Manual: & Warranty Card
Instruction Manual: & Warranty Card
4 Chapter 1: Introduction
4 Safety instructions
7 Recommendations
7 Special features
7 Getting started
8 Product set
9 Parts of the structure
10 Chapter 2: Operation
10 Assembly instructions (for juice)
12 Cooking steps
14 Cleaning and maintenance
16 Assembly instructions (for puree)
17 Reminder for user
19 Chapter 3: Troubleshooting
21 Chapter 4: Other
21 Specifications
22 Servicing
3
INTRODUCTION
SAFETY INSTRUCTIONS
Danger symbol
A reminder to user about high voltage.
Warning symbol
A reminder to user about the necessity of operating exactly according to the instructions.
IWhen using electrical appliances should take Do not use the device in areas where the air
the following precautions: can contain vapors of flammable substances.
Use the device according to the following Never attempt to open the device by
operation guide. yourself it could possibly be the reason
of an electrical shock, can lead to product
Install the device on a stable surface. malfunction and will invalidate the
manufacturers warranty. For repair and
Use only the tools which are the included maintenance, contact only authorized
in the product set. service centers meant for repair of products
under the trademark OURSSON.
To protect against risk of electrical shock
do not put the cord in water or other liquid. When moved from a cool to a warm place
If for some reason the water got into and vice versa unpack it before use and
the unit, contact an authorized service wait 1-2 hours without turning it on.
center (ASC) OURSSON AG.
In order to prevent electrical shock do not
For power supply use a power grid with immerse the entire product or the wires into
proper characteristics. the water.
4
INTRODUCTION
Be particularly careful and cautious when Make sure to disconnect the device from
using the device near children. the power grid before cleaning or changing
accessories.
Do not touch any moving parts, as this may
cause injury. Do not use the device outdoors.
The power cord is specially made relatively This appliance is not intended for use by
short in order to avoid the risk of injury. persons (including children) with reduced
physical, sensory or mental capabilities,
Do not allow the cord to hang over the
or lack of experience and knowledge.
sharp edge of the table or touch hot
They can only use the device under the
surfaces.
supervision of the person responsible for
Do not connect this device to a grid which their safety, or after instruction on the safe
is overloaded with other appliances: use of the device. Do not allow children to
it can lead to the fact that the device will not play with the product.
function properly.
Use the product for its intended purpose.
Do not install the device near gas and
electric stoves and ovens. This product is intended only for use
in the home.
After use, make sure to disconnect
the device from the power grid. If the power cord is damaged, it must be
replaced by a specialist from the authorized
Keep the device from bumps, falls, vibration service center ( ASC ) OURSSON AG
and other mechanical influences. to avoid danger.
5
OPERATION
Always make sure the device Weight of the device is approximately 6.45
is disconnected before cleaning. kg. Be careful and cautious when moving
it in order to avoid injury or damage to the
Do not use abrasive cleaning materials, device.
organic cleaning products (alcohol,
gasoline etc.). In order to avoid possible malfunctions of
the device, do not wash it in hot water with
When cleaning the device it is allowed to a temperature above 80, because some
use a small amount of neutral detergent. elements are made of silicone.
Make sure that the switch is in the If the mesh filter is damaged, stop using the
OFF position after each use. Before device and contact the authorized service
disassembling the device, also make sure center (ASC) OURSSON AG.
that the motor has stopped completely.
6
INTRODUCTION
Please read the instruction manual before Before using the cold press juice maker for the
using the device. Keep the manual after first time, please carefully wash it as described
reading for further use. in instructions. Your press juice maker is now
ready for use.
All illustrations in this manual are schematic
representations of real objects, which may
differ from the actual images.
SPECIAL FEATURES
7
INTRODUCTION
PRODUCT SET
8
INTRODUCTION
1 Feeding chute 1
2 Juice bowl cover
3 Pressure screw
4 Three-tier mesh filter 2
5 Rotating brush
6 Juice bowl
7 Spout for pulp
3
8 Spout for juice
9 Motor base
10 Puree bowl cover 4
11 Puree bowl 5
12 Pusher
13 Cleaning brush
14 Juice pitcher
15 Pulp container 6
7
NOTE! If the bowl is not installed
10 8
correctly on the motor base,
a protective mechanism is
triggered and the device does
not turn on. To turn on the
device, install and properly
fix the bowl on the base, as 11
9
12 13 14 15
9
OPERATION
Pressure
screw
Juice bowl
Mesh filter
Protection
mechanism
1. Install the juice bowl on motor base. 3. Insert the pressure screw in the center
Slowly rotate the bowl clockwise until of three-tier mesh filter as shown in Fig.3.
it stops (Fig.1).
4. Install the cover. Place the juice bowl cover
2. Install the three-tier mesh filter in the on the juice bowl so that the mark on the
rotating brush before installing it in the juice bowl coincides with the mark on the cover.
bowl. Install the three-tier mesh filter with a Then, slowly turn the bowl cover clockwise
rotating brush so that the mark on the mesh until the mark on the cover coincides
filter coincides with the mark on the bowl as with the mark on the handle, as shown
shown in Fig. 2. in Fig. 4, Fig. 5.
Marks on the
bowl cover
Rotating brush
Marks on the
juice bowl
Marks on the
bowl handle
Motor base
2 4
10
OPERATION
Bowl cover
Juice
Marks on the pitcher
bowl handle
5 7
5. To install the silicone baffle for spout, place 6. Plug the device to the outlet. Place the
the baffle as shown in Fig. 6. Then, install juice pitcher and the pulp container around
the free end of the baffle into the hole the motor base under the corresponding
located at the bottom of the spout for pulp. spouts, as shown in Fig. 7.
Fixing
silicone baffle Insertion hole
Bowl
with installed
baffle
Silicone
baffle
Insertion
direction
6
11
OPERATION
COOKING STEPS
2. Turn on the device, pressing the button 3. Using the pusher, place the washed and
on its back. (Fig.1). The switch has three peeled (if needed) ingredients in the feeding
positions: chute. Remove the seeds from fruit with
large seeds, such as plums, apricots and
ON Turns on the device;
peaches, before placing them in the chute.
OFF Shutdown, stops the motor;
4. When the juice is ready, turn off the device
REV Reverse. and unplug it from outlet (Fig. 2).
1 2
ON ON
Pusher
REV REV
ON ON
REV REV
Push
Push
ON Reverse ON Reverse
12
OPERATION
NOTE! Do not use spoons or any If pressure screw abruptly stops rotating,
first turn off the device. Then switch the button
other foreign objects to remove
to the bottom position REV to remove the
pulp from the spout, as this
ingredients that block the pressure screw.
may damage the device. Then turn on the device.
If that does not help, unplug the device from the
outlet, disassemble and clean it, as described.
Turn on Turn off Reverse.
NOTE! Use only the pusher included
in the product set to push
ingredients in feeding chute.
It is strictly forbidden to push
ingredients with hands, as this
may cause injury.
Turn on
ON
Turn on
OFF OFF
NOTE! Fresh juices should be
consumed immediately. Reverse
13
OPERATION
4 5
14
OPERATION
5. Do not immerse the motor base in water. 6. After cleaning, dry thoroughly all the parts of
Clean it with a damp soft cloth. the device. Store in a clean, dry place.
15
OPERATION
ASSEMBLY INSTRUCTIONS
(FOR PUREE)
1. Install the puree bowl on motor base. Then, slowly turn the bowl cover clockwise
Slowly rotate the bowl clockwise until until the mark on the cover coincides
it stops (Fig. 1). with the mark on the handle, as shown
in Fig. 3, Fig. 4.
Puree bowl
cover
Puree bowl
Marks on the
bowl cover
Marks on the
bowl handle
Motor base 1 3
Pressure
screw
Bowl cover
Marks on the
bowl handle
Motor base
2 4
2. Install the pressure screw in the center of the Use the puree bowl to grind the following
bowl, as shown in Fig. 2. products: garlic, ginger, chili pepper, spices,
sauces, baby food.
3. Install the cover. Place the puree bowl cover
on the puree bowl so that the mark on the
bowl coincides with the mark on the cover.
16
OPERATION
For juice: install the juice bowl on motor When juicing finishes, you can switch
base. Slowly rotate the bowl clockwise the device on REV (reverse) mode for
until it stops. After that, install the rotating 2-5 seconds for easier disassembly.
brush, the three-tier mesh filter and the
pressure screw. Close the bowl with cover 3. If the device is overloaded or the products
by turning it clockwise until it stops. are too hard or sticky, the screw can stop.
If pressure screw abruptly stops rotating,
For puree: install the puree bowl on motor first turn off the device. Then use the
base. Slowly rotate the bowl clockwise reverse function REV for 3-5 seconds.
until it stops. After that, install the pressure Then turn on the device. This procedure
screw. Close the bowl with cover by can be repeated several times.
turning it clockwise until it stops.
4. If you cannot open the cover, switch
Disassembly order the device on REV (reverse) mode for
2-5 seconds. This will make fruit and
First, remove the bowl cover by turning vegetables, which are stuck in the device
it counterclockwise. After that, remove the and block the cover, move in the opposite
remaining parts of device in reverse order direction. Turn off the device and remove
of assembling it. Rinse all the removable the cover, slowly rotating it.
parts under running water with a cleaning
brush, dry them thoroughly and store 5. Pretreating products:
in a clean, dry place.
Hard products, such as carrots, radish
2. How to place products: and other root vegetables should be cut
into 2cm pieces.
If needed, the products have to be
pretreated, washed, peeled or cut into Sticky and fibrous products (greens).
pieces. Add the products slowly as the If stems are thick, cut them and separate
speed operation is low (the pressure from leaves.
17
OPERATION
Pretreating fruit.
18
TROUBLESHOOTING
Device does not work on Check whether the power cord is connected
to the outlet. If the device is not connected, plug
it to the outlet.
Decreased juice rate, pulp Check whether the device is assembled correctly.
contains too much liquid If not, disassemble and reassemble according
to the instructions.
The device has stopped working Make sure the amount of fruit and vegetables
is not too large and the motor is not overloaded.
19
TROUBLESHOOTING
Bowl cover does not open When juicing finishes, switch the device
properly on REV (reverse) mode for 2-5 seconds for
easier disassembly and use more power to rotate
the cover counterclockwise.
20
OTHER
Specifications
Model JM8002
Weight, kg 6,45
Note! Only a qualified specialist of an authorized service center OURSSON AG can repair
the juice maker.
21
OTHER
SERVICING
22
OTHER
3. OURSSON AG sets for its products the If the defect was a result of careless
following terms of use and warranty handling, use for other purpose, violations
periods: of conditions and rules of operation set
forth in the instruction manual, including
Terms of Warranty
Product name as a result of exposure to high or low
use Period
Microwave ovens, temperatures, high humidity or dust, traces
breadmakers, 60 12 of opening the device independently and/
induction hobs or self-repair, mismatch state standards
Multicookers, for power grids, getting liquids, insects or
kitchen processors other foreign objects, substances inside
electric kettles, the device, as well as long-term use of the
electric grills, product in extreme operational modes.
hand blenders,
If the defect of the product was a result of
hand mixers, meat 36 12
grinders, blenders, unauthorized attempts to test the product
toasters, airpots, or make any changes in its construction
toasters, juicers, or software programs, including repair or
steamers, coffee maintenance in unauthorized service centers.
makers, choppers If the defect of the product was a result
Kitchen scales 24 12 of use of non-standard and/or low quality
equipment, accessories, spare parts,
4. Warranty obligations OURSSON AG shall batteries.
not apply to the following products, if their If the defect of the product is associated
replacement is assumed and is not connected with its use in conjunction with additional
with disassembling products: equipment (accessories), other than
Batteries. additional equipment recommended by
Cases, straps, cords for carrying, mounting OURSSON AG for use with this product.
accessories, tools, documentation that OURSSON AG is not responsible for
came with the product. the quality of the additional equipment
(accessories) manufactured by third parties,
5. Warranty does not cover defects caused for the quality of its products together with
due to violations of the rules of consumer use, such equipment, as well as the quality of
storage or transportation of the goods, actions the work of the additional equipment of
of third parties or force majeure, including but OURSSON AG together with the products
not limited to the following cases: of other manufacturers.
23
OTHER
24
OTHER
Using the product when after the terms Product Recycling and Disposal
of use (lifetime):
After the expiration of the lifetime,
1. Lifetime set by OURSSON AG for this the product cannot be disposed with
product applies only when the product is another household waste. Instead, it
used exclusively for personal, family or shall be deposited in the appropriate
household needs, as well as the consumer recycling collection point for electrical and
observes the correct operation, storage electronic equipment for proper treatment
and transportation of products. Under the and disposal in accordance with federal or
condition of careful handling of the product local law. By disposing correctly this product,
and compliance with the rules of operation you will help to conserve natural resources
the actual life may exceed the lifetime set and preventing the product from damaging
by OURSSON AG. the environment and human health. For
more information on the collection point and
2. At the end of the product lifetime, you recycling of this product, please contact your
should contact an authorized service center local municipal authorities or the enterprise for
for to conduct a preventive maintenance of household waste disposal.
the product and determine the suitability
for further use. Work on conducting a
preventive maintenance of the products is
also made in service centers on paid basis.
25
OTHER
Date of manufacture
Each product has a unique serial number in
Note! To avoid misunderstandings,
the form of alphanumeric row and is duplicated
we highly recommend you to
with a barcode that contains the following
read carefully the instruction
information: name of the product group, date
manual and the warranty
of manufacture, serial number of the product.
obligations. Check the
Serial number is located on the rear of the
correctness of the warranty
product, on the package and the warranty
card. card. Warranty card is valid
only if the following are
correctly and clearly stated:
model, serial number, date
JM1225011234567
of purchase, clear stamps,
1 2 3 4
buyers signature. The serial
number and the model of the
1 The first two letters - correspondence to the
device must be the same as
product group (juice maker JM).
in the warranty card. If these
2 The first two digits year of manufacture.
conditions are not fulfilled
3 The second two digits week of
or the data specified in the
manufacture.
4 The last two digits serial number of
warranty card was changed,
product. the warranty card is invalid.
26
OURSSON AG hotline provides complete information about the companys activity in Russia, CIS and Baltic countries.
Professional operators quickly answer to any question. You can contact the unified center for service support, for
recommendations about the setup and connection, to get information about local sales, with questions about the
promotions and yearly drawings conducted by the company, as well as with any other questions about the company's
activities on the territory of Russia, CIS and Baltic countries.
Any questions? Call us, we can help!
Hotline OURSSON AG (free calls from landline phones)
8 800 100 8708.
The hotline work schedule is: Monday-Friday from 9:00 to 20:00 (Moscow time). Saturday, Sunday and public holidays
are rest days.
This manual is under protection of international and Russian copyright law. Any unauthorized use of the instructions,
including copying, printing and distribution, but not limited to, involves the application of the guilty person to civil
liability and criminal liability in accordance with Article 146 of the Criminal Code and the administrative responsibility in
accordance with Article 7.12 of the Administrative Code (previously Article 150.4).
Contact information:
1. Manufacturer of goods - OURSSON AG (Orson AG) Utokvay 39, 8008 Zurich, Switzerland.
2. Organization authorized to accept and meet the demands for the goods of poor quality, - BBK Service Center,
109202, Moscow, Fraser Highway 17A, 1A.
OURSSON AG
MADE IN KOREA
WARRANTY CARD
A Filled by the service center
Filled by the selling company
DATE OF RECEPTION
DATE OF RECEPTION DATE OF ISSUE
ORDER NUMBER service
DATE OF ISSUE DEFECT DESCRIPTION center
service stamp
center SPECIALIST
SPECIAL NOTES stamp
IRS CODE
WARRANTY CARD
B Filled by the service center
Filled by the selling company
DATE OF RECEPTION
DATE OF RECEPTION DATE OF ISSUE
ORDER NUMBER service
DATE OF ISSUE DEFECT DESCRIPTION center
service stamp
center SPECIALIST
SPECIAL NOTES stamp
IRS CODE
WARRANTY CARD
C Filled by the service center
Filled by the selling company
DATE OF RECEPTION
DATE OF RECEPTION DATE OF ISSUE
ORDER NUMBER service
DATE OF ISSUE DEFECT DESCRIPTION center
service stamp
center SPECIALIST
SPECIAL NOTES stamp
IRS CODE
Warranty card
Filled by the selling company
WARRANTY
DEVICE
MODEL
SERIAL NUMBER
DATE OF SALE
SELLING COMPANY
Please ask the seller to fill completely the warranty card and the warranty
Note! tickets.
WARRANTY CARD
Filled by the selling company
DEVICE
MODEL
service
SERIAL NUMBER
center
DATE OF SALE stamp
SELLING COMPANY
WARRANTY CARD B
Filled by the selling company
DEVICE
MODEL
service
SERIAL NUMBER
center
DATE OF SALE stamp
SELLING COMPANY
WARRANTY CARD C
Filled by the selling company
DEVICE
MODEL
service
SERIAL NUMBER
center
DATE OF SALE stamp
SELLING COMPANY
Hotline OURSSON AG
(free calls from landline phones): www.oursson.ru
8 800 100 8 708
This file was downloaded from the site
mans.io
Samsung
Pioneer
Alpine
LG
Dell
Sharp
Sony
Philips
Epson
Netgear