Viewtenddoc Asp
Viewtenddoc Asp
Viewtenddoc Asp
GRAND SUMMARY
TOTAL AMOUNT
S. NO. DESCRIPTION AMOUNT DSR 2016 AMOUNT NON-DSR
(DSR + NON-DSR)
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount Non-DSR Amount
(DSR + NS)
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount NS Amount
(DSR + NS)
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount Non-DSR Amount
(DSR + NS)
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount NS Amount
(DSR + NS)
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount NS Amount
(DSR + NS)
2 SH-II STRUCTURED CABLING SYSTEM PASSIVE, IP-PBX SYSTEM & LOCAL-AREA NETWORK
37,90,025.00
(LAN)Rs. 37,90,025.00
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount NS Amount
(DSR + NS)
1 SH-I PASSENGER LIFT (2 Nos.) - 55,43,000.00 Rs. 55,43,000.00
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount NS Amount
(DSR + NS)
1 SH-I FIRE FIGHTING WORK 3,80,516.00 101,50,949.00 Rs. 105,31,465.00
Summary sheet for Construction of Shivpuri Institute of Technology at Shivpuri, Madhya Pradesh
Total Amount
S.No. Sub-head Description DSR Amount NS Amount
(DSR + NS)
1 SH-I TUBEWELLS PUMP - 1,62,200.00 Rs. 1,62,200.00
1.1 1.1.2 Carriage of materials by mechanical transport including loading, unloading and stacking 1,500.00 Cum 98.34 1,47,510.00
for earth - lead 1 Km.
1.2 2.10.1 Excavating trenches of required width for pipes, cables etc. including excavation for
sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out
the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in
depth including consolidating each deposited layer by ramming, watering etc. and
disposing of surplus excavated soil as directed, within a lead of 50m.- All kinds of soil
(Including Soft Rock)
a) 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. 3,300.00 Metre 138.05 4,55,565.00
b) 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 4,000.00 Metre 225.45 9,01,800.00
c) 2.10.1.3 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm 700.00 Metre 352.00 2,46,400.00
1.3 2.11 Extra for excavating trenches for pipes, cables etc. in all kinds of soil (Including Soft Rock)
for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item
for depth upto 1.5 metre).
a) Pipes, cables etc, not exceeding 80 mm dia. 1,200.00 Metre 175.32 2,10,384.00
b) Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 1,600.00 Metre 286.32 4,58,112.00
c) Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm 200.00 Metre 447.04 89,408.00
1.5 2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, 1,100.00 Cum 917.75 10,09,525.00
consolidating and dressing complete.
1.6 2.32 Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of 9,200.00 Sqm 3.65 33,580.00
the area cleared.
1.7 2.34 Supplying chemical emulsion in sealed containers including delivery as specified. 1,800.00 Ltr. 185.95 3,34,710.00
2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
1.8 2.35 Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti-termite
treatment (excluding the cost of chemical emulsion)
a) 2.35.2 Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 2,000.00 Metre 24.30 48,600.00
litres per linear metre including drilling and plugging holes etc.:
2.35.2.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration
b) 2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 8,500.00 Sqm 131.90 11,21,150.00
mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1
cement : 2 Coarse sand) to match the existing floor.
2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
c) 2.35.5 Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane 1,100.00 Metre 191.40 2,10,540.00
(in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at
downward angle of 45 degree at 150 mm centre to centre and sealing the same
2.1 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of
centering and shuttering - All work up to plinth level :
a) 4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone agg. 20 mm nominal size) 40.00 Cum 5,481.95 2,19,278.00
b) 4.1.5 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone agg. 20 mm nominal size). 40.00 Cum 4,927.00 1,97,080.00
c) 4.1.8 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone agg. 40 mm nominal size) 1,800.00 Cum 4,478.15 80,60,670.00
2.2 4.2 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)
including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses,
string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills,
fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering
and finishing :
4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 70.00 Cum 6,547.70 4,58,339.00
2.3 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for : 425.00 Sqm 193.95 82,429.00
4.3.1 Foundations, footings, bases for columns
2.4 4.10 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement 450.00 Sqm 263.10 1,18,395.00
: 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)
2.5 4.12 Extra for providing and mixing water proofing material in cement concrete work in doses by 1,200.00 Per 50 kg 47.95 57,540.00
2.6 4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 1,050.00 Sqm 450.35 4,72,868.00
6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40
mm nominal size, well rammed and consolidated and grouted with fine sand, including
necessary excavation, levelling & dressing & finishing the top smooth.
TOTAL CONCRETE WORK 96,66,599.00
3.1 5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 160.00 Cum 7,390.80 11,82,528.00
15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and
spiral stair cases above plinth level up to floor five level, excluding the cost of centering,
shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) :
3 graded stone aggregate 20 mm nominal size).
3.2 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :
a) 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 4,900.00 Sqm 193.95 9,50,355.00
b) 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses 450.00 Sqm 378.60 1,70,370.00
etc.
c) 5.9.3 Suspended floors, roofs, landings, balconies and access platform 28,000.00 Sqm 422.30 118,24,400.00
d) 5.9.4 Shelves (Cast in situ) 280.00 Sqm 422.30 1,18,244.00
e) 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers 18,000.00 Sqm 342.90 61,72,200.00
f) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and struts. 15,000.00 Sqm 467.85 70,17,750.00
g) 5.9.7 Stairs, (excluding landings) except spiral-staircases. 900.00 Sqm 419.35 3,77,415.00
h) 5.9.13 Vertical and horizontal fins individually or forming box louvers band, facias and eaves 100.00 Sqm 627.85 62,785.00
boards
i) 5.9.14 Extra for shuttering in circular work (20% of respective centering and shuttering items)
For Columns 1,800.00 Sqm 93.57 1,68,426.00
j) 5.9.15 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string 500.00 Sqm 193.95 96,975.00
courses, bands, copings, bed plates, anchor blocks and the like
k) 5.9.16.1 Edges of slabs and breaks in floors and walls - Under 20 cm wide 210.00 Metre 122.20 25,662.00
l) 5.9.17 Cornices and mouldings 180.00 Sqm 565.10 1,01,718.00
m) 5.9.19 Weather shade, Chajjas, corbels etc., including edges 650.00 Sqm 521.75 3,39,138.00
3.3 5.11 Extra for additional height in centering, shuttering where ever required with adequate 700.00 Sqm 171.50 1,20,050.00
bracing, propping etc., including cost of de-shutteringand decentering at all levels, over a
height of 3.5 m, for every additionalheight of 1 metre or part thereof (Plan area to be
measured).
5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
3.4 5.18 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 160.00 Sqm 814.55 1,30,328.00
graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire,
including centering and shuttering, roughening cleaning, fixing and finishing with cement
mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills
and soffits.
5.18.1 50 mm thick
3.5 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in 5,88,000.00 Kg 56.60 332,80,800.00
position and binding all complete upto plinth level.
5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.
3.6 5.22A Reinforcement for RCC work including straightening, cutting, bending, placing in position 14,26,000.00 Kg 56.60 807,11,600.00
and binding all complete. Above plinth level.
5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.
3.7 5.23 Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 450.00 Sqm 143.80 64,710.00
(1 Cement : 3 fine sand).
3.8 5.26 Providing and filling in position, blown bitumen in expansion joints. 1.00 Cum 50,192.70 50,193.00
3.9 5.28 Providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to 900.00 per cm 449.10 4,04,190.00
IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints. depth per
100 m
5.29 Providing and fixing sheet covering over expansion joints with iron screws as per design. 240.00 Mtr. 336.65 80,796.00
5.29.2.1 Aluminium fluted strips 3.15 mm thick - 150 mm wide
3.10 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 2,150.00 Mtr. 34.15 73,423.00
3.11 5.33 Providing and laying in position machine batched and machine mixed design mix M-25
grade cement concrete for reinforced cement concrete work, using cement content as per
approved design mix, including pumping of concrete to site of laying but excluding the cost
(Note :- Cement content considered in this item is @ 330 kg/cum.Excess/ less cement
used as per design mix is payable/recoverable separately).
3.11.1 5.33.1 a) All works upto plinth level 2,950.00 Cum 6,446.45 190,17,028.00
3.11.2 5.33.2 b) All works above plinth level upto floor V level 8,250.00 Cum 7,250.05 598,12,913.00
3.12 5.34 Extra for providing richer mixes at all floor levels.
Note:- Excess/less cement over the specified cement content used is payable
/recoverable separately.
5.34.1 Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content 1,850.00 Cum 69.50 1,28,575.00
considered in M-30 is @ 340 kg/cum)
3.13 5.43 Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design 1,150.00 Mtr. 584.10 6,71,715.00
for expansion joints.
5.43.1 200 mm wide.
TOTAL REINFORCED CEMENT CONCRETE WORK 2231,54,287.00
4.1 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in
foundation and plinth in:
a) 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 40.00 Cum 4,970.30 1,98,812.00
b) 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 1,450.00 Cum 4,751.65 68,89,893.00
4.2 6.34 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10
average compressive strength in super structure above plinth level up to floor V level in :
a) 6.34.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 250.00 Cum 6,359.65 15,89,913.00
b) 6.34.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 4,250.00 Cum 6,167.20 262,10,600.00
4.3 6.45 Half brick masonry with non modular fly ash bricks of class designation 10, conformingio 15,200.00 Sqm 769.50 116,96,400.00
IS :12894, in super structure above plinth and upto floor V level.
6.45.2 Cement mortar 1:4 (1 cement :4 coarse sand)
4.4 6.47 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 1,050.00 Cum 5,687.10 59,71,455.00
mm thick AAC blocks in super structure above plinth level up to floor V level with RCC
band at sill level and lintel level with approved block laying polymer modified adhesive
mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band
and reinforcement shall be made for seperately).
TOTAL BRICK WORK 525,57,073.00
5.1 7.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with 80.00 Cum 3,965.85 3,17,268.00
cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm
nominal size) upto plinth level with :
7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand)
5.2 7.2 Random rubble masonry with hard stone in superstructure above plinth level and upto floor 50.00 Cum 4,795.15 2,39,758.00
five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12
graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.
5.3 7.5 Extra for random rubble masonry with hard stone curved on plan for a mean radius not 50.00 Cum 481.70 24,085.00
exceeding 6 m.
TOTAL STONE WORK 5,81,111.00
6.1 8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and 490.00 Sqm 3,351.95 16,42,456.00
prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and
similar locations of required size, approved shade, colour and texture laid over 20 mm
thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,
mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and
polishing to edges to give high gloss finish etc. complete at all levels.
8.2.2.1 Granite of any colour and shade - Area of slab upto 0.50 sqm
6.2 8.3 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including
machine polishing to edge to give high gloss finish etc. complete as per design approved
by Engineer-in-Charge.
a) 8.3.1 a) Marble work 1,150.00 Mtr. 144.70 1,66,405.00
b) 8.3.2 b) Granite work 3,200.00 Mtr. 245.70 7,86,240.00
6.3 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen 450.00 Each 427.95 1,92,578.00
platform, vanity counter and similar location in marble/ Granite/stone work, including
necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges
etc. complete.
6.4 8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high 2,400.00 Sqm 231.50 5,55,600.00
gloss finish complete.
6.5 8.10 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 1,500.00 Sqm 2,831.95 42,47,925.00
75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate
width with chase cutter and embedding the stone in the chase with epoxy grout or with
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm
nominal size) as per direction of Engineer-in-charge and finished smooth.
6.6 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in 1,500.00 Sqm 2,937.70 44,06,550.00
linear as well as curvilinear portions of the building, all complete as per the architectural
drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar
1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white
cement slurry admixed with pigment of matching shade, including rubbing, curing and
polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
TOTAL MARBLE & GRANITE WORK 119,97,754.00
7.1 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, 30.00 Cum 92,743.05 27,82,292.00
wrought framed and fixed in position with hold fast lugs or with dash fasteners of required
dia & length (hold fast lugs or dash fastener shall be paid for separately).
9.1.1 Second class teak wood
7.2 9.12 Extra for providing frosted glass panes 4mm thick instead of ordinary float glass panes 200.00 Sqm 74.35 14,870.00
4mm thick in doors, windows& clerestory windows, shutters (Area of opening for glass
panes excluding portion inside rebate shall be measured)
7.3 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) 1,050.00 Sqm 2,488.95 26,13,398.00
decorative type, core of block board construction with frame of 1st class hard wood and
well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on
both faces of shutters.
9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
7.4 9.21 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- 1,550.00 Sqm 1,559.75 24,17,613.00
decorative type, core of block board construction with frame of 1st class hard wood and
well matched commercial 3 ply veneering with vertical grains or cross bands and face
veneers on both faces of shutters:
9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
7.5 9.22 Extra for Providing and fixing flush doors with decorative veneering instead of non 700.00 Sqm 394.90 2,76,430.00
decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)
9.22.1 On one side only
7.6 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all 2,100.00 Sqm 365.85 7,68,285.00
edges of flush door shutters (over all area of door shutter to be measured).
7.7 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 100.00 Sqm 127.75 12,775.00
7.8 9.33 Providing and fixing expandable fasteners of specified size with necessary plastic sleeves 2,500.00 Each 22.65 56,625.00
and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and
making good etc. complete.
9.33.4 50 mm long
7.9 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and 50.00 Each 556.45 27,823.00
a pair of lever handles with necessary screws etc. Complete (best make of approved
quality).
7.10 9.78 Providing and fixing bright finished brass night latch of approved quality including 50.00 Each 794.55 39,728.00
necessary screws etc. complete.
7.11 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door 60.00 Each 388.40 23,304.00
closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to
80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with
necessary accessories and screws etc. complete.
7.12 9.96 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not
less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade,
with nuts and screws etc. complete :
a) 9.96.1 300x16 mm 300.00 Each 212.45 63,735.00
b) 9.96.2 250x16 mm 410.00 Each 189.20 77,572.00
7.13 9.97 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less
than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with
necessary screws etc. complete :
a) 9.97.2 250x10 mm 800.00 Each 88.10 70,480.00
b) 9.97.4 150x10 mm 2,350.00 Each 64.30 1,51,105.00
7.14 9.100 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less
than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with
necessary screws etc. complete :
a) 9.100.1 125 mm 1,600.00 Each 51.10 81,760.00
b) 9.100.2 100 mm 1,300.00 Each 45.10 58,630.00
7.15 9.101 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic 960.00 Each 38.00 36,480.00
coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour
and shade, with necessary screws etc. complete.
9.101.2 Twin rubber stopper
7.16 9.102 Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of 420.00 Each 473.65 1,98,933.00
handles of approved quality for aluminium door, with necessary screws etc complete as
per direction of Engineer- in-charge.
7.17 9.127 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / 4,000.00 Sqm 518.00 20,72,000.00
matt/ suede finish with high density protective surface layer and reverse side of adhesive
bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved
quality.
9.127.2 1.0 mm thick
7.18 9.134 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with 600.00 Sqm 3,005.45 18,03,270.00
wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors,
windows and clerestory windows with necessary screws :
9.134.2.2 30 mm thick shutters - With ISI marked stainless steel butt hinges of required size
9.134.2.2.1 Second class teak wood
7.19 9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding 400.00 Each 124.40 49,760.00
window with necessary screws etc. complete.
7.20 9.151 Providing and fixing steel roller for uPVC sliding window with necessary screws etc. 400.00 Each 72.15 28,860.00
complete.
7.21 9.152 Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete. 400.00 Each 112.80 45,120.00
7.22 9.165 Providing and fixing bright /matt finished Stainless Steel handles of approved quality &
make with necessary screws etc all complete.
a) 9.165.1 125 mm 1,050.00 Each 89.70 94,185.00
b) 9.165.2 100 mm 850.00 Each 66.50 56,525.00
TOTAL WOOD WORK 139,21,558.00
8.1 10.1 Structural steel work in single section, fixed with or without connecting plate, including 900.00 Kg 58.45 52,605.00
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all
complete.
8.2 10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed 1,900.00 Kg 67.60 1,28,440.00
work, including cutting, hoisting, fixing in position and applying a priming coat of approved
steel primer all complete.
8.3 10.6 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, 75.00 Sqm 2,316.10 1,73,708.00
interlocked together through their entire length and jointed together at the end by end
locks, mounted on specially designed pipe shaft with brackets, side guides and
arrangements for inside and outside locking with push and pull operation complete,
including the cost of providing and fixing necessary 27.5 cm long wire springs
manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -
part 1 and M.S. top cover of required thickness for rolling shutters.
10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover
8.4 10.7 Providing and fixing ball bearing for rolling shutters. 24.00 Each 379.30 9,103.00
8.5 10.8 Extra for providing mechanical device chain and crank operation for operating rolling 30.00 Sqm 724.05 21,722.00
shutters.
10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area
8.6 10.14 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from
commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead
and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of
1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,
including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and
shock absorbers as specified and applying a coat of approved steel primer after pre-
treatment of the surface as directed by Engineer-in-charge:
10.14.1 Profile B
a) 10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb 1,900.00 Mtr. 340.35 6,46,665.00
b) 10.14.1.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for 800.00 Mtr. 332.30 2,65,840.00
separately)
10.14.2 Profile C
c) 10.14.2.1 Fixing with adjustable lugs with split end tail to each jamb 900.00 Mtr. 363.55 3,27,195.00
d) 10.14.2.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for 380.00 Mtr. 355.55 1,35,109.00
separately)
8.7 10.16 Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., 6,500.00 Kg 90.25 5,86,625.00
including cutting, hoisting, fixing in position and applying a priming coat of approved steel
primer, including welding and bolted with special shaped washers etc. complete.
8.8 10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, 900.00 Each 130.10 1,17,090.00
of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top
surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet
box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall
8.9 10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in 16,500.00 Kg 85.95 14,18,175.00
position and applying a priming coat of approved steel primer using structural steel etc. as
required.
10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
8.10 10.27 Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of
10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head,
comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame ,
concrete/ masonry, etc. as per direction of Engineer-in-charge.
a) 10.27.2 10 x 80 mm 600.00 Each 74.75 44,850.00
b) 10.27.3 10 x 120 mm 700.00 Each 91.80 64,260.00
c) 10.27.4 10 x 140 mm 750.00 Each 102.80 77,100.00
d) 10.27.5 10 x 160 mm 800.00 Each 125.65 1,00,520.00
8.11 10.28 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, 8,000.00 Kg 472.40 37,79,200.00
plates etc., including welding, grinding, buffing, polishing and making curvature (wherever
required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c
fixing the railing with necessary accessories & stainless steel dash fasteners, stainless
steel bolts etc., of required size, on the top of the floor or the side of waist slab with
suitable arrangement as per approval of Engineer-incharge, (for payment purpose only
weight of stainless steel members shall be considered excluding fixing accessories such
as nuts, bolts, fasteners etc.).
TOTAL STEEL WORK 79,48,207.00
9.1 11.3 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 100.00 Sqm 362.60 36,260.00
finished with a floating coat of neat cement, including cement slurry, but excluding the cost
of nosing of steps etc. complete.
11.3.1 40 mm thick with 20 mm nominal size stone aggregate
9.2 11.5 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm 160.00 Sqm 609.05 97,448.00
thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm
nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement
hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening
9.3 11.6 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse 30.00 Sqm 350.05 10,502.00
sand), finished with a floating coat of neat cement.
11.6.1 18 mm thick
9.4 11.13 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 300.00 Mtr. 52.50 15,750.00
11.13.1 40 mm wide and 4 mm thick
9.5 11.20 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with
neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and
cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse
sand).
a) 11.20.1 Light shade pigment using white cement 400.00 Sqm 906.75 3,62,700.00
b) 11.20.3 Dark shade pigment using ordinary cement 1,600.00 Sqm 716.35 11,46,160.00
9.6 11.23 Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by
Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4
coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing
complete with :
a) 11.23.2 Raj Nagar plain 200.00 Sqm 1,522.60 3,04,520.00
b) 11.23.4 Black Zebra 180.00 Sqm 1,389.05 2,50,029.00
c) 11.23.5 Udaipur green marble 4,400.00 Sqm 1,589.40 69,93,360.00
9.7 11.24 Extra for pre finished nosing to treads of steps of marble stone. 900.00 Mtr. 306.25 2,75,625.00
9.8 11.25 Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 250.00 Sqm 357.95 89,488.00
metre.
9.9 11.30 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 900.00 Sqm 813.10 7,31,790.00
(1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1
cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing
with same mortar.
11.30.1 Red sand stone
9.10 11.31 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. 450.00 Mtr. 84.85 38,183.00
9.11 11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness 6,500.00 Sqm 744.80 48,41,200.00
to be specified by the manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting,
risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white
cement mixed with pigment of matching shade complete.
9.12 11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be 8,400.00 Sqm 688.35 57,82,140.00
specified by the manufacturer) of 1st quality conforming t0o IS : 15622 of approved make
in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement
mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm
including pointing the joints with white cement and matching pigment etc., complete.
9.13 11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more 1,900.00 Sqm 822.45 15,62,655.00
(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of
approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick
cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @
3.3kg/sqm including grouting the joints with white cement and matching pigments etc.,
complete.
9.14 11.41 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the
manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of
approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1
cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting
the joints with white cement and matching pigments etc., complete.
a) 11.41.2 Size of Tile 600x600 mm 14,500.00 Sqm 1,119.40 162,31,300.00
b) 11.41.3 Size of Tile 800x800 mm 1,800.00 Sqm 1,414.95 25,46,910.00
9.15 11.46 Providing and laying Vitrified tiles in different sizes (thickness to be specified by
manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of
approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of
cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @
3.3kg/sqm including grouting the joint with white cement & matching pigments etc.
complete.
10.1 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 160.00 Each 187.60 30,016.00
(1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C.
sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse
sand) and a coat of neat cement, rounding the edges and making and finishing the outlet
complete.
10.2 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to
IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm
gap for thermal expansion, (i) Single socketed pipes.
a) 12.41.1 75 mm diameter 800.00 Metre 148.75 1,19,000.00
b) 12.41.2 110 mm diameter 1,600.00 Metre 236.35 3,78,160.00
10.3 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for
unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including
jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
c) 12.42.3.1 Single tee with door - 75x75x75 mm 100.00 Each 121.50 12,150.00
d) 12.42.3.2 Single tee with door - 110x110x110 mm 140.00 Each 181.55 25,417.00
10.4 12.43 Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised -
PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S.
screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1
cement : 4 coarse sand) and making good the wall etc. complete.
a) 12.43.1 75 mm 250.00 Each 182.55 45,638.00
b) 12.43.2 110 mm 950.00 Each 181.40 1,72,330.00
10.5 12.46 Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering 160.00 Each 66.45 10,632.00
Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing
not less than 100 gms.
10.6 12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work 1,400.00 Sqm 806.20 11,28,680.00
made of special sections, power pressed from M.S. sheets and galvanized with zinc
coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats
of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre
to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with
6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of
required length with nuts & bolts of required size and other end of angle hanger fixed with
intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to
centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered
flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed
in a direction perpendicular to G.I. intermediate channel with connecting clips made out of
2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels
0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of
ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long
dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and
perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,
including jointing and finishing to a flush finish of tapered and square edges of the board
with recommended jointing compound , jointing tapes , finishing with jointing compound in
3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for
board, all as per manufacturer's specification and also including the cost of making
openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels
suitably fixed, all complete as per drawings, specification and direction of the Engineer in
Charge but excluding the cost of painting with :
12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I
10.7 12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of 900.00 Sqm 550.40 4,95,360.00
corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness
with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns
epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should
have protective guard film of 25 microns minimum to avoid scratches during transportation
and should be supplied in single length upto 12 metre or as desired by Engineerin-charge.
The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with
EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding
the cost of purlins, rafters and trusses and including cutting to size and shape wherever
required.
10.8 12.51 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05
%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa
steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-
18 microns using self drilling/ self tapping screws complete :
a) 12.51.1 Ridges plain (500 - 600mm) 90.00 Metre 360.45 32,441.00
b) 12.51.6 Gutter (600 mm over all girth) 90.00 Metre 833.05 74,975.00
10.9 12.52 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true
horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel
sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner
with suitably spaced joints to get required length and of size 24x38 mm made from 0.30
mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size
24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main
"T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of
length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be
interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall
angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid
including, required cutting/making, opening for services like diffusers, grills, light fittings,
fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI
slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm
long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size
85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed
width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for
all heights as per specifications, drawings and as directed by Engineer-in-charge.
a) 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, 350.00 Sqm 1,041.95 3,64,683.00
and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm
(both sides inclusive) and electro statically polyester powder coated of thickness 60
microns (minimum), including factory painted after bending.
b) 12.52.4 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass 2,800.00 Sqm 1,005.35 28,14,980.00
fibre conforming to IS:2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm
at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with
non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79,
with 50 mm resin bonded glass wool backing.
TOTAL ROOFING 57,76,942.00
11.2 13.2.1 15 mm cement plaster on the rough side of single or half brick wall of mix :
a) 13.2.1 1:4 (1 cement: 4 fine sand) 200.00 Sqm 200.25 40,050.00
b) 13.2.2 1:6 (1 cement: 6 fine sand) 24,400.00 Sqm 185.20 45,18,880.00
11.4 13.4 15 mm cement plaster on the rough side of single or half brick wall of mix :
a) 13.4.1 1:4 (1 cement: 4 coarse sand) 50.00 Sqm 209.65 10,483.00
b) 13.4.2 1:6 (1 cement: 6 fine sand) 50.00 Sqm 194.60 9,730.00
11.5 13.11 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 24,200.00 Sqm 255.55 61,84,310.00
5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine
sand).
11.8 13.22 Extra for plastering exterior walls of height more than 10 m from ground level for every 4,500.00 Sqm 40.65 1,82,925.00
additional height of 3 m or part thereof.
11.9 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to 24,500.00 Sqm 118.70 29,08,150.00
prepare the surface even and smooth complete.
11.10 13.33 Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) :
a) 13.44.1 Flush/ Ruled pointing 250.00 Sqm 168.45 42,113.00
b) 13.44.2 Raised and cut pointing 250.00 Sqm 305.70 76,425.00
11.11 13.44 Finishing walls with water proofing cement paint of required shade: 3,800.00 Sqm 58.80 2,23,440.00
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm)
11.12 13.47 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of 22,000.00 Sqm 96.80 21,29,600.00
required shade:
13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of
exterior primer applied @ 2.20 kg/10 sqm)
11.14 13.60 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an 56,500.00 Sqm 84.45 47,71,425.00
even shade :
13.60.1 Two or more coats on new work
11.15 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even 4,500.00 Sqm 78.40 3,52,800.00
shade :
13.61.1 a) Two or more coats on new work
11.17 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved 30,800.00 Sqm 87.35 26,90,380.00
brand and manufacturer, over the plastered wall surface to prepare the surface even and
smooth complete.
TOTAL FINISHING WORK 310,07,790.00
12.1 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity 12,500.00 Sqm 90.10 11,26,250.00
after excavating earth to an average of 22.5 cm depth, dressing to camber and
consolidating with road roller including making good the undulations etc. and re-rolling the
sub grade and disposal of surplus earth with lead upto 50 metres.
12.2 16.2 Extra for compaction of earth work in embankment under optimum moisture conditions to 1,400.00 Cum 10.70 14,980.00
give at least 95% of the maximum dry density (proctor density).
12.4 16.4 Laying spreading and compacting stone aggregate of specified sizes to WBM 4,800.00 Cum 449.10 21,55,680.00
specifications including spreading in uni form thickness, hand picking, rolling with 3
wheeled road/vibratory roller 8-10 tonne in stages to proper grade and camber, applying
and brooming requisite type of screening/binding material to fill up interstics of coarse
aggregate watering and compacting to the required density.
12.5 16.18 Fencing with angle iron post placed at required distance embedded in cement concrete 900.00 Metre 12.65 11,385.00
blocks, every 15th post, last but one end post and corner post shall be strutted on both
sides and end post on one side only and provided with horizontal lines and two diagonals
interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum),
between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost
of posts, struts, earth work and concrete work to be paid for separately). Payment to be
made per metre cost of total length of barbed wire used.
16.18.1 With G.I. barbed wire
12.6 16.30 Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including 12,500.00 Sqm 36.40 4,55,000.00
heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on
bitumen boiler, cleaning and preparing the existing road surface as per specifications :
12.7 16.57 Providing and laying Bituminous concrete using crushed stone aggregates of specified
grading, premixed with bituminous binder and filler, transporting the hot mix to work site by
tippers, laying with paver finisher equiped with electronic sensor to the required grade,
level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to
achieve the desired compaction and density as per specification, complete and as per
directions of Engineer-in-Charge.
16.57.1 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by 500.00 Cum 7,863.85 39,31,925.00
weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in
Batch Type Hot Mix Plant of 100-120 TPH capacity.
12.8 16.59 Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick
aluminum sheet, face to be fully covered with high intensity encapsulated type heat
activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and
silver white or other colour combination including subject matter, message (bi-lingual),
symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive
backing which shall be activated by applying heat and pressure conforming to class -2 of
ASTM-D-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20 cm
c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant
measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical
post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size
100x100x5 mm at the bottom end and including making holes in pipes, angles flats,
providing & fixing M.S. message plate of required size, steel work to be painted with two or
more coats of synthetic enamel paint of required shade and of approved brand &
manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to
be painted in black and white colours).Backside of aluminum sheet to be painted with two
or more coats of epoxy paint over and including appropriate priming coat including all
leads and lifts etc. complete as per drawing , specification and direction of Engineer--
incharge.
a) 16.59.1 Mandatory/regulatory sign boards of 900 mm diametre with part as length of 3750 mm 50.00 Sqm 4,786.35 2,39,318.00
b) 16.59.2 Cautionary /warning sign boards of equilateral triangular shape having each side of 900 25.00 Sqm 3,464.05 86,601.00
mm with support length of 3650 mm
12.9 16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade 150.00 Cum 5,012.65 7,51,898.00
cement in position to the required line ,level and curvature jointed with cement mortar 1:3
(1 cement : 3 coarse sand) including making joints with or without grooves (thickness of
joints except sharp curve shall not be more than 5mm) including making drainage opening
12.1 16.71 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm 200.00 Sqm 594.15 1,18,830.00
made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and
washers as required complete as per the direction of Engineer-in-charge.
12.11 16.91 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot 2,400.00 Sqm 638.95 15,33,480.00
path, park & lawns driveway or light & traffic parking etc. of required strength, thickness &
size/ shape, made by table vibratory method using PU mould, laid in required colour &
pattern over 50mm thick compacted bed of course sand, compacting and proper
embedding/laying of inter locking paver blocks into the sand bedding layer through
vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver
blocks as per required size and pattern, finishing and sweeping extra sand, all complete as
per manufacturer's specifications & direction of Engineer-in-Charge.
16.91.2 80mm thick Cement concrete paver block of M-30 grade with approved colour, design &
pattern.
TOTAL ROAD WORKS : 180,95,492.00
13.1 17.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand 10.00 Each 3,494.20 34,942.00
cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe,
with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good the walls and floors wherever
required:
17.1.1 White Vitreous china Orissa pattern W.C. pan of size
580x440 mm with integral type foot rests
13.2 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm 385.00 Each 1,817.35 6,99,680.00
C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting
and making good the walls wherever require:
17.7.4 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P.
brass pillar tap
13.3 17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. 50.00 Each 2,476.60 1,23,830.00
brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting
and making good the walls wherever required :
17.10.2.1 Kitchen sink without drain board - 610x510 mm bowl depth 200 mm
13.4 17.11 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass 20.00 Each 3,211.45 64,229.00
chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary
C.P. brass unions complete, including painting of fittings and brackets, cutting and making
good the wall wherever required :
17.11.2 Size 600x450x200 mm
13.5 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste 425.00 Each 73.25 31,131.00
fittings complete.
17.28.2.1 Flexible pipe - 32 mm dia
13.6 17.31 Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved 400.00 Each 817.95 3,27,180.00
quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P.
brass screws and washers complete.
13.7 17.69 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality
and colour.
a) 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 360.00 Each 82.55 29,718.00
gms
b) 17.69.2 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 70.00 Each 98.80 6,916.00
gms
13.8 17.7 Providing and fixing PTMT Bottle Trap for Wash basin and sink.
a) 17.70.1 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 380.00 Each 293.95 1,11,701.00
260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water
seal, weighing not less than 260 gms
b) 17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 70.00 Each 305.55 21,389.00
260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water
seal, weighing not less than 263 gms
13.9 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with 70.00 Each 422.70 29,589.00
CP brass screws with concealed fittings arrangement of approved quality and colour.
17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88
mm, weighing not less than 190 gms.
13.10 17.78 Providing and fixing white vitreous china extended wall mounting water closet of size 350.00 Each 9,685.70 33,89,995.00
780x370x690 mm of approved shape including providing & fixing white vitreous china
cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8
litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
13.11 17.80 Providing and fixing white vitreous china battery based infrared sensor operated urinal of 150.00 Each 5,162.20 7,74,330.00
approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml
consumption), having water inlet from back side, including fixing to wall with suitable
brackets all as per manufacturers specification and direction of Engineer-in-charge.
TOTAL SANITARY INSTALLATIONS 56,44,630.00
14.1 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply, including all CPVC plain & brass threaded fittings, including
fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with
one step CPVC solvent cement and testing of joints complete as per direction of Engineer
in Charge. Internal work - Exposed on wall
a) 18.7.2 20 mm nominal outer dia Pipes 1,800.00 Metre 179.95 3,23,910.00
b) 18.7.3 25 mm nominal outer dia Pipes 1,000.00 Metre 216.20 2,16,200.00
c) 18.7.4 32 mm nominal outer dia Pipes 900.00 Metre 289.05 2,60,145.00
d) 18.7.5 40 mm nominal outer dia Pipes 400.00 Metre 385.50 1,54,200.00
e) 18.7.6 50 mm nominal outer dia Pipes 300.00 Metre 548.55 1,64,565.00
14.2 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the
pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step
CPVC solvent cement and the cost of cutting chases and making good the same including
testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc.
a) 18.8.2 20 mm nominal outer dia Pipes 3,800.00 Metre 284.85 10,82,430.00
14.3 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply including all CPVC plain & brass threaded fittings This includes
jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing
of joints complete as per direction of Engineer in Charge.
External work
a) 18.9.3 25 mm nominal outer dia Pipes 700.00 Metre 191.65 1,34,155.00
b) 18.9.4 32 mm nominal outer dia Pipes 700.00 Metre 250.55 1,75,385.00
c) 18.9.5 40 mm nominal outer dia Pipes 600.00 Metre 321.15 1,92,690.00
d) 18.9.6 50 mm nominal outer dia Pipes 200.00 Metre 484.25 96,850.00
e) 18.9.7 62.50 mm nominal inner dia Pipes 350.00 Metre 1,081.75 3,78,613.00
f) 18.9.8 75 mm nominal inner dia Pipes 700.00 Metre 1,201.05 8,40,735.00
14.4 18.13 Making connection of G.I. distribution branch with G.I. main of following sizes by providing
and fixing tee, including cutting and threading the pipe etc. complete :
18.13.1 25 to 40 mm nominal bore 38.00 Each 394.15 14,978.00
14.5 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed
a) 18.17.1 25 mm nominal bore 76.00 Each 428.20 32,543.00
b) 18.17.2 32 mm nominal bore. 64.00 Each 500.75 32,048.00
c) 18.17.3 40 mm nominal bore. 60.00 Each 584.70 35,082.00
14.6 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with
plastic floats complete :
a) 18.18.1 15 mm nominal bore 50.00 Each 287.25 14,363.00
b) 18.18.2 20 mm nominal bore 20.00 Each 327.05 6,541.00
c) 18.18.3 25 mm nominal bore 20.00 Each 331.95 6,639.00
14.7 18.21 Providing and fixing unplasticised PVC connection pipe with brass unions : 1,100.00 Each 67.80 74,580.00
18.21.2.1 45 cm length - 15 mm nominal bore
14.8 18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 230.00 Each 71.65 16,480.00
18.22.1 100 mm diameter
14.9 18.27 Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS -
1536
18.27.1 100 mm diameter pipe 250.00 Metre 1,078.25 2,69,563.00
14.10 18.32 Constructing brick masonry chamber 30x30x50cms inside with 1st class brick work in
cement mortar 1:5 (1 cement : 5 fine sand) for stop cock with CI surface box
100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)necessary
excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate
40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement 3 coarse
sand) 12mm thick finished with a floating coat of neat cement complete as per standard
design. (For Garden Hydrant)
18.32.1 With FPS bricks (Class I) 50.00 Each 1,195.35 59,768.00
14.11 18.33 Constructing masonry Chamber 60X60X75 cm, inside with 75 class designation brick work
in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100
mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and
RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm
nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10
graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3
(1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement
complete as per standard design:
18.33.1 With common burnt clay F.P.S (non modular) bricks of classs designation 7.5 10.00 Each 6,849.60 68,496.00
14.12 18.34 Constructing masonry Chamber 90X90X100 cm, inside with 75 class designation brick
work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box
100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid
and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm
nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10
graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3
(1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement
complete as per standard design:
14.13 18.34.1 With common burnt clay F.P.S (non modular) bricks of classs designation 7.5 10.00 Each 11,842.75 1,18,428.00
14.14 18.41 Providing and filling sand of grading zone V or coarser grade all-round the GI/CPVC pipes
in external work.
a) 18.41.3 25 mm nominal outer dia Pipes 700.00 Metre 69.50 48,650.00
b) 18.41.4 32 mm nominal outer dia Pipes 700.00 Metre 71.30 49,910.00
c) 18.41.5 40 mm nominal outer dia Pipes 600.00 Metre 72.25 43,350.00
d) 18.41.6 50 mm nominal outer dia Pipes 200.00 Metre 74.95 14,990.00
e) 18.41.7 65 mm nominal outer dia Pipes 350.00 Metre 118.30 41,405.00
f) 18.41.8 80 mm nominal outer dia Pipes 700.00 Metre 121.90 85,330.00
14.15 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 3,00,000.00 Per Litre 7.25 21,75,000.00
12701 marked, with cover and suitable locking arrangement and making necessary holes
for inlet, outlet and overflow pipes but without fittings and the base support for tank.
18.48.1 Circular tank
14.16 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 435.00 Each 371.70 1,61,690.00
18.49.1 15 mm nominal bore
14.17 18.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS 500.00 Each 492.55 2,46,275.00
standards and weighing not less than 690 gms.
18.51.1 15 mm nominal bore
14.18 18.52 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved 310.00 Each 545.95 1,69,245.00
make conforming to IS:8931.
18.52.1 15 mm nominal bore
14.19 18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved 1,150.00 Each 475.70 5,47,055.00
quality conforming to IS:8931
18.53.1 15 mm nominal bore
14.20 18.58 Providing and fixing PTMT grating of approved quality and colour.
a) 18.58.1.1 Circular type - 100 mm nominal dia 280.00 Each 32.75 9,170.00
b) 18.58.1.2 Circular type - 125 mm nominal dia with 25 mm waste hole 470.00 Each 45.55 21,409.00
14.21 18.60 Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and 1.00 Each 3,104.90 3,105.00
tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces
if required will be paid separately):
18.60.1 100mm dia nominal bore
TOTAL WATER SUPPLY 83,85,971.00
15.1 19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of
cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints
etc. complete ::
a) 19.1.1 100 mm diameter 400.00 Metre 216.25 86,500.00
b) 19.1.2 150 mm diameter 800.00 Metre 327.05 2,61,640.00
15.2 19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone
aggregate 40 mm nominal size) all-round S.W./R.C.C. pipes including bed concrete as per
standard design:
a) 19.2.1 100 mm diameter S.W. / RCC pipe 400.00 Metre 622.95 2,49,180.00
b) 19.2.2 150 mm diameter S.W. / RCC pipe 800.00 Metre 761.85 6,09,480.00
c) 19.2.4 250 mm diameter S.W. / RCC pipe 1,500.00 Metre 1,027.00 15,40,500.00
15.3 19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone
aggregate 40 mm nominal size) up to haunches of S.W./RCC pipes including bed concrete
as per standard design :
19.3.4 300 mm dia. R.C.C. pipe 2,200.00 Metre 656.60 14,44,520.00
15.4 19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating
brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside)
the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as
per standard design:
a) 19.4.1 100 x 100 mm size P type 110.00 Each 1,602.40 1,76,264.00
19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
15.5 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed
with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand)
including testing of joints etc. complete :
a) 19.6.1 100 mm dia. R.C.C. pipe 100.00 Metre 325.55 32,555.00
b) 19.6.2 150 mm dia. R.C.C. pipe 150.00 Metre 356.70 53,505.00
c) 19.6.3 250 mm dia. R.C.C. pipe 1,500.00 Metre 482.05 7,23,075.00
d) 19.6.4 300 mm dia. R.C.C. pipe 2,200.00 Metre 518.55 11,40,810.00
e) 19.6.5 450 mm dia. R.C.C. pipe 450.00 Metre 720.95 3,24,428.00
f) 19.6.6 500 mm dia. R.C.C. pipe 80.00 Metre 950.30 76,024.00
g) 19.6.7 600 mm dia. R.C.C. pipe 100.00 Metre 1,397.10 1,39,710.00
h) 19.6.9 800 mm dia. R.C.C. pipe 50.00 Metre 1,770.85 88,543.00
15.6 19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand )
with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded
stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making
channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size) finished with a floating coat of neat cement complete as per standard
design :
19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610
mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight
of cover 23 kg and weight of frame 15 kg) :
19.7.1.2 With Sewer bricks conforming to IS : 4885 80.00 Each 8,678.85 6,94,308.00
15.8 19.9 Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m
dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm
thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of
neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm
nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat
of neat cement all complete as per standard design:
19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm
internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less
than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation,
foot rests and 12 mm thick cement plaster at the external surface shall be paid for
separately) :
19.9.1.2 With Sewer bricks conforming to IS : 4885 70.00 Each 8,743.70 6,12,059.00
15.9 19.10 Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to
1.67m.
19.10.2 With Sewer bricks conforming IS : 4885 20.00 Metre 5,020.95 1,00,419.00
15.10 19.11 Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at
top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with
cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement
foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm
nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat
15.11 19.12 Extra depth for circular type manhole 1.22m internal dia (at bottom)
beyond 1.68 m to 2.29 m :
19.12.2 With Sewer bricks conforming IS : 4885 150.00 Metre 6,505.15 9,75,773.00
15.12 19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as 500.00 Each 327.90 1,63,950.00
per IS: 10910 on 12mm dia steel bar conforming to IS :1786 having minimum cross section
as 23 mm x 25 mm and over all minimum length 263mm and width as 165mm with
minimum 112mm space between protruded legs having 2mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring projections on tail length
on 138mm as per standard drawing and suitable to with stand the bend test and chemical
resistance test as per specifications and heaving manufactures permanent identification
mark to be visible even after fixing " including fixing in manholes with 30x20x15 cm cement
concrete block 1:3:6: (1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal
size) complete as per design.
15.13 19.19 Providing and fixing in position precast RCC manhole cover and frame of required shape
and approved quality.
19.19.3.1 HD-20 circular shape 560 mm internal diameter. 8.00 Each 1,300.95 10,408.00
15.16 19.21 Making connection of drain or sewer line with existing manhole including breaking into and
making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement
mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and
making necessary channels for the drain etc. complete :
19.21.2 For pipes 250 to 300 mm diameter 20.00 Each 463.45 9,269.00
15.17 19.27 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar
1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating
16.1 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with
extruded built up standard tubular sections/ appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required
dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and
sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed mechanically wherever required including
cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the directions of Engineer-in-
charge. (Glazing, panelling and dash fasteners to be paid for separately) :
a) 21.1.1 For fixed portion 6,850.00 Kg 391.80 26,83,830.00
21.1.1.3 Polyester powder coated aluminium (minimum thickness of polyester powder coating 50
micron).
b) 21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots 33,500.00 Kg 452.40 151,55,400.00
and making provision for fixing of fittings wherever required including the cost of EPDM
rubber / neoprene gasket / rolleres required.
21.1.2.3 Polyester powder coated aluminium (minimum thickness of polyester powder coating 50
micron)
16.2 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions
etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings
and the directions of engineer-in-charge.
21.3.1 a) With float glass panes of 4.00 mm thickness 225.00 Sqm 741.50 1,66,838.00
21.3.2 a) With float glass panes of 5.50 mm thickness 1,250.00 Sqm 1,003.95 12,54,938.00
16.3 21.4 Providing and fixing double action hydraulic floor spring of approved brand and 80.00 Each 2,054.40 1,64,352.00
manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with
double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting
floors, embedding in floors as required and making good the same matching to the existing
floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with
slide plate etc. complete as per the direction of Engineer-in-charge.
21.4.1 With stainless steel cover plate minimum 1.25 mm thickness
16.4 21.8 Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by providing 1,000.00 Metre 62.45 62,450.00
weather silicon sealant over backer rod of approved quality as per architectural drawings
and direction of Engineer-in-Charge complete
21.8.1 Upto 5mm depth and 5mm width
16.5 21.10 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, 780.00 Sqm 3,176.20 24,77,436.00
ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air
gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant
(Both primary and secondary sealant) etc. as per specifications, drawings and direction of
Engineer-in-charge complete.
16.6 21.11 Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of 1,600.00 Each 211.60 3,38,560.00
approved quality with necessary stainless steel screws etc. to the side hung windows as
per direction of Engineerin-charge complete.
21.11.1 205 X 19 mm
16.7 21.17 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required 5,100.00 Kg 408.85 20,85,135.00
shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved
design/pattern, with approved standard section and fixed to the existing window frame with
C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to
proper opening size for fixing and operation of handles and fixing approved anodised
aluminium standard section around the opening, all complete as per requirement and
direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
16.8 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved 160.00 Sqm 4,608.85 7,37,416.00
brand and manufacture, including providing and fixing top & bottom pivot & spring type
fixing arrangement and making necessary holes etc. for fixing required door fittings, all
complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be
paid separately).
TOTAL ALUMINIUM WORK 251,26,355.00
17.1 22.1 Providing and laying integral cement based treatment for water proofing on horizontal
surface at all depth below ground level for under ground structures as directed by Engineer-
in-Charge and consisting of : i) Ist layer of 22 mm to 25 mm thick approved and specified
rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand)
mixed with water proofing compound conforming to IS:2645 in the recommended
proportion over the leveling course (leveling course to be paid separately). Joints sealed
and grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of 25
mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing
compound in recommended proportions. iii) Finishing top with stone aggregate of 10 mm
to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.
17.2 22.2 Providing and laying integral cement based treatment for water proofing on the vertical
surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with
water proofing compound conforming to IS:2645 in recommended proportions with a gap
of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps
with neat cement slurry mixed with water proofing compound and finishing the exterior of
stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat
cement punning mixed with water proofing compound in recommended proportion
complete at all levels and as directed by Engineer-in-charge :
22.2.1 Using rough kota stone. 600.00 Sqm 1,253.30 7,51,980.00
17.3 22.4 Providing and Placing in position suitable PVC water stops conforming to IS:12200 for
construction/ expansion joints between two RCC members and fixed to the reinforcement
with binding wire before pouring concrete etc. complete :
22.4.1 Serrated with central bulb (225 mm wide, 8-11 mm thick) 180.00 Metre 254.15 45,747.00
17.4 22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by 1,450.00 Sqm 298.30 4,32,535.00
applying cement slurry mixed with water proofing cement compound consisting of applying
: a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement
compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second
layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @
0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing
for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints,
17.5 22.6 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry 8,500.00 Sqm 395.00 33,57,500.00
mixed with water proofing cement compound consisting of applying:
a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with
water proofing cement compound @ 0.253 kg/sqm.
b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of
joints of fibre cloth should not be less than 10 cm.
c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed
with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm.
This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire
treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all
around.
d) fourth and final layer of white ceramic glazed tile with cement mortar (which will be paid
for separately.For the purpose of measurement the entire treated surface will be
measured.
18.1 23.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method
prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing
and submitting strata chart/bore log, including hire & running charges of all equipments,
tools, plants & machineries required for the job, all complete as per direction of Engineer
in-charge, upto 90 metre depth below ground level.
23.1.1.1 All types of soil - 300 mm dia. 450.00 Metre 370.70 1,66,815.00
18.2 23.2 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method
prescribed in IS: 2800 (part I), including collecting samples from different strata,
preparing and submitting strata chart/bore log, including hire & running charges of
all equipments, tools, plants & machineries required for the job, all complete as per
direction of Engineer in-charge, beyond 90 metre & upto 150 metre depth below ground
level.
23.2.1.1 All types of soil - 300 mm dia. 60.00 Metre 432.45 25,947.00
18.3 23.3 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized
PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including
required hire and labour charges, fittings & accessories etc. all complete, for all depths, as
per direction of Engineer in-charge
23.3.2 150 mm nominal size dia 320.00 Metre 572.30 1,83,136.00
18.4 23.4 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized
PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire &
labour charges, fittings & accessories etc. all complete, for all depths, as per direction of
Engineer-in-charge.
23.4.2 150 mm nominal size dia 190.00 Metre 529.35 1,00,577.00
18.5 23.5 Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in 44.00 Cum 921.90 40,564.00
recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of
Engineer-in-charge.
18.6 23.6 Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the 36.00 Cum 1,038.05 37,370.00
recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts,
all complete as per direction of Engineer-incharge.
18.7 23.7 Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in 45.00 Cum 1,038.05 46,712.00
recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per
direction of Engineer in-charge.
18.8 23.8 Gravel packing in tubewell construction in accordance with IS: 4097, including providing 25.00 Cum 1,175.60 29,390.00
gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all
complete as per direction of Engineer-in-charge.
18.9 23.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to 450.00 Hour 542.20 2,43,990.00
establish maximum rate of usable water yield without sand content (beyond
permissible limit), with required capacity air compressor, running the compressor for
required time till well is fully developed, measuring yield of well by "V" notch
method or any other approved method, measuring static level & draw down etc. by
step draw down method, collecting water samples & getting tested in approved
laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air
compressor, tools & accessories etc., all as per requirement and direction of
Engineer-in-charge.
18.10 23.13 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top
of bore well housing/ casing pipe, removable as per requirement, all complete for
borewell of:
23.13.2 150 mm dia 5.00 Each 182.95 915.00
18.11 23.14 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of
tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size
complete.
23.14.2 150 mm clamp. 5.00 Each 1,017.70 5,089.00
18.12 23.15 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly
of tubewell as per IS:2800 (part I).
23.15.2 150 mm dia 5.00 Each 230.75 1,154.00
TOTAL RAIN WATER HARVESTING & TUBEWELLS 8,81,659.00
19.1 25.2 Designing, fabricating, testing, protection, installing and fixing in position semi (grid) 350.00 Sqm 2,409.90 8,43,465.00
unitized system of structural glazing (with open joints) for linear as well as curvilinear
portions of the building for all heights and all levels, including:
a) Structural analysis & design and preparation of shop drawings for the specified design
loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times
design wind pressure without any failure), including functional design of the aluminum
sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and
splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather
silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM
gaskets for water tightness, pressure equalisation & drainage and protection against fire
hazard including:
b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5
brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional
movement for achieving perfect verticality and fixing structural glazing system rigidly to the
RCC/ masonry/structural steel framework of building structure using stainless steel anchor
fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc.
of stainless steel grade 316, of the required capacity and in required numbers.
c) Providing and filling, two part pump filled, structural silicone sealant and one part
weather silicone sealant compatible with the structural silicone sealant of required bite size
in a clean and controlled factory / work shop environment , including double sided spacer
tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per
the approved sealant design, within and all around the perimeter for holding glass.
d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of
sizes, shapes and profiles, as required as per the site conditions, to seal the gap between
the building structure and all its interfaces with curtain glazing to make it watertight.
e) PMaking provision for drainage of moisture/ water that enters the curtain glazing system
to make it watertight, by incorporating principles of pressure equalization, providing
suitable gutter profiles at bottom (if required), making necessary holes of required sizes
and of required numbers etc. complete. This item includes cost of all inputs of designing,
labour for fabricating and installation of aluminium grid, installation of glazed units, T&P,
scaffolding and other incidental charges including wastages etc., enabling temporary
structures and services, cranes or cradles etc. as described above and as specified. The
item includes the cost of getting all the structural and functional design including shop
drawings checked by a structural designer, dully approved by Engineer-in-charge. The
item also includes the cost of all mock ups at site, cost of all samples of the individual
components for testing in an approved laboratory, field tests on the assembled working
structural glazing as specified, cleaning and protection till the handing over of the building
for occupation. In the end, the Contractor shall provide a water tight structural glazing
having all the performance characteristics etc. all complete as required, as per the
Architectural drawings, as per item description, as specified, as per the approved shop
drawings and as directed by the Engineer- in-Charge.
Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded
aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof
stainless steel wire mesh shall be paid for separately under relevant items under this sub-
head. However, for the purpose of payment, only the actual area of structural glazing
(including width of grooves ) on the external face shall be measured in sqm. up to two
decimal places.
Note:- 2. The following performance test are to be conducted on structural glazing system
if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated
by NABL(National Accreditation Board for Testing and Calibration Laboratories),
Department of Science & Technologies, India. Cost of testing is payable separately. The
NIT approving authority will decide the necessity of testing on the basis of cost of the work,
cost of the test and importance of the work. Performance Testing of Structural glazing
system Tests to be conducted in the NBL Certified laboratories
1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to
+300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr
2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method
for a range up to 2000 ml.
3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method
for a range upto 2000 ml
4. Structural Performance Deflection and deformation by static air pressure test (1.5 times
desing wind pressure without any failure) as per ASTME-330-10 testing method for a
range upto 50 mm
5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for
Qualitative test. Tests to be conducted on site.
5. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto
2000 ml
19.2 25.3 Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically- 350.00 Sqm 3,730.70 13,05,745.00
sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as
required and specified, comprising of an outer heat strengthened float glass 6mm thick, of
approved colour and shade with reflective soft coating on surface # 2 of approved colour
and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm
wide, dessicants, including primary seal and secondary seal (structural silicone sealant)
etc. all complete for the required performances, as per the Architectural drawings, as per
the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The
IGUs shall be assembled in the factory/ workshop of the glass processor.(Payment for
fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)For payment,
only the actual area of glass on face # 1 of the glass panels (excluding the areas of the
grooves and weather silicone sealant) provided and fixed in position, shall be measured in
sqm.
(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, +
12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties
as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light
reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3
W/m2 degree K etc. The properties of performance glass shall be decided by technical
sanctioning authority as per the site requirement.
19.3 25.4 Extra for openable side / top hung vision glass panels (IGUs) including providing and 30.00 Sqm 2,941.60 88,248.00
supplying at site all accessories and hardwares for the openable panels as specified and
of the approved make such as heavy duty stainless steel friction hinges, min 4 -point
cremone locking sets with stainless steel plates, handles, buffers etc. including necessary
stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the
Architectural drawings, as per the approved shop drawings, as specified and as directed
by the Engineer- in-Charge.
TOTAL STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL 22,37,458.00
EARTH WORK
1.0 NS Earth work in excavation for foundation trenches or drains, all areas, in all kind of soil, 21,000.00 Cum 280.00 58,80,000.00
ordinary/soft rock by mechanical means (Hydraulic excavator) / manual means for all
depth and width including getting out the excavated soil, loading, unloading, disposal of
the surplus excavated soil / soft rock for all lead and lift as directed by Engineer-in-charge.
2.0 NS Filling available excavated earth in trenches, plinth, sides of foundations etc. in layers not 11,500.00 Cum 90.00 10,35,000.00
exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, all
lead and lift. (Excavated fractured rock upto 40mm size shall also be considered for filling)
with minimum of 90% of Relative density.
3.0 NS Supplying and filling up ground depressions, in plinth, area development, roads on
slopes/embankments with Moorum Soil transported from borrow areas arranged by the
contractor at his own cost, including excavation, loading, transportation and unloading of
suitable materials to the filling site, loosening, laying and spreading in layers, breaking
lumps, compacting each layer not exceeding 300 mm compacted thickness to minimum of
specified relative density, dressing to the required slopes/shapes, level, in camber for road
embankments/paving, finishing of surfaces, all leads and lifts in respect of excavation,
transportation and placement of fill material, complete as per specifications, drawings and
directions of the Engineer. compacted volume in filling only shall be measured for
payment.
a) Minimum of 90% of Relative density. 36,000.00 Cum 220.00 79,20,000.00
b) Minimum of 95% of Relative density. 24,000.00 Cum 225.00 54,00,000.00
TOTAL EARTH WORK 202,35,000.00
R.C.C. WORK
4.0 NS Less for not pumping of Design Mix concrete to site for laying. 600.00 Cum -232.00 -1,39,200.00
5.0 NS Deduct for using Cement PPC instead of OPC-43 in all cement work 50,000.00 Qtls. -23.00 -11,50,000.00
6.0 NS Designing, supplying and fixing rebars in already cast conrete, including drilling, cleaning
hole with air blow out & wire brush and injecting ETA certified epoxy based chemical for
rebar fixing in dry, water saturated condition / submerged holes condition for 8mm to
32mm dia, with the help of dispenser into a hole diameter and depth as per manufacturer
specification, at all levels & locations for fixing high strength deformed steel reinforcement
bars of Grade Fe 500D (cnforming to IS: 1786). Chemical should be made of two
components consisting of resin and hardener in theratio 5:1 in a foil pack of 330/500 ml.
The chemical should not propagate corrosin of rebar and should be tested for it as per
SGK or equivalent certificate.
a) 10 mm dia 100.00 Each 415.00 41,500.00
b) 12 mm dia 100.00 Each 580.00 58,000.00
Core Cutting
7.0 NS Providing accurate and clean holes of 25 to 200 mm dia range without vibration with wet
drilling through diamond coring tool system for passing conduits, cable, pipes etc. The
holes drilled should have following characteristics:
1. The system should be capable of cutting reinforcement upto 28 mm.
2. The hole geometry should be absolutely round as per the diameter of hole required.
3. The system should be vibration free - means it should not damage the structur in the
vicnity of hole being drilled.
4. Repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement
: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing
complete so as to make it leak proof.
a) Depth upto200 mm 1,700.00 Each 275.00 4,67,500.00
R.C.C. WORK -7,22,200.00
BRICK WORK
8.0 NS Extra for using cement flyash F.P.S. (non modular) brick of class designation 7.5 in place 21,25,000.00 Each 1.20 25,50,000.00
of clay brick in brick work at all floor level:
TOTAL BRICK WORK 25,50,000.00
WOOD WORK
9.0 NS Providing and fixing bright /matt finished Stainless Steel Sliding door bolt of approved
quality & make with necessary screws etc all complete.
a) a) 300x16 mm 225.00 Each 360.00 81,000.00
10.0 NS Providing and fixing bright /matt finished Stainless Steel Tower bolt of approved quality &
make with necessary screws etc all complete.
a) a) 250x10 mm 550.00 Each 150.00 82,500.00
b) b) 150x10 mm 1,550.00 Each 110.00 1,70,500.00
11.0 NS Providing and fixing bright /matt finished Stainless Steel hanging door stopper of approved 600.00 Each 65.00 39,000.00
quality & make with necessary screws etc all complete.
a) Twin rubber stopper
TOTAL WOOD WORK 4,62,600.00
STEEL WORK
12.0 NS Supplying, fitting & fixing at all levels MS chequered plate as per direction of Engineer in 500.00 Kg 62.00 31,000.00
charge on MS angle support welded properly including necessary anchoring arrangement
as per drawing compete with three coat of synthetic enamel paint over a coat of appoved
steel primer.
13.0 NS Supplying, fitting & fixing MS rod at all levels of dia upto 40mm as per drawing complete 500.00 Kg 55.00 27,500.00
with three coat of synthetic enamel paint over a coat of appoved steel primer.
TOTALSTEEL WORK 58,500.00
14.0 NS Providing and fixing 18mm thick Granite stone in Dado / wall lining in cement mortar 1:3 450.00 Sqm 4,110.00 18,49,500.00
(1cement : 3 coarse sand) including pointing with white cement mortor with an admixture
of pigment to match the granite shade including rubbing & polishing complete at all levels
as per direction of Engineer-in-charge.
15.0 NS Prepolished Kota stone slab 18mm thick in flooring, steps over 20 mm (average) thick 5,500.00 Sqm 1,440.00 79,20,000.00
base laid over and jointed with grey cement slurry mixed with pigment to match the shade
of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1
cement : 4 coarse sand) :
16.0 NS Prepolished Kota stone slabs 18 mm thick in risers of steps, skirting, dado and pillars laid 900.00 Sqm 1,480.00 13,32,000.00
on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with
grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing
and polishing complete.
17.0 NS Extra for Kota stone in treads of steps and risers using single length up to 2.00 metre. 240.00 Sqm 28.00 6,720.00
18.0 NS Providing and fixing Glass mossaic tiles at finished plain wall surface of size 10 mm x 10 25.00 Sqm 1,850.00 46,250.00
mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in-
Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved
adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is
inclusive of all operation, material and required pattern approved by Engineer-in-Charge.
Recommended Brand - Bisazza, Paladio or Cora.
TOTAL FLOORING AND STONE WORK 111,54,470.00
ROOFING
19.0 NS Providing & fixing trap door in the false ceiling using 19 mm thick commercial block board 12.00 Sqm 2,200.00 26,400.00
laminated with approved finish 1mm thick laminate with necessary 2nd Class teak frame
work of size 2" x 1.5", Oak wood mouldings as per Architects drawing, brass hinges,
latches etc. complete in all respect as directed by Engineer-in-charge.
20.0 NS Extra for Providing 15 mm thick mineral fibre board tile manufactured from high density 2,000.00 Sqm 345.00 6,90,000.00
glass wool /rock wool of size 595mmx595mm with rebated edge having an NRC (Noise
Reductin Coefficient) of 0.7 or more, light reflectance not less than 83% and able to
withstand a permanrnt ambient RH upto 95% without sagging of Armstrong or similar make
as per manufacturer specifications in place of perforated gypsum board in Item No. 10.7
(b) (DSR Item no 12.52.4)
TOTAL ROOFING 7,16,400.00
FINISHING WORK
21.0 NS Providing and fixing 24 gauge 12 mm size galvanised chicken wire mesh of approved 4,800.00 Sqm 75.00 3,60,000.00
width at junctions of concrete, brick work, below POP and other locations, as required,
including necessary laps and U shape galvanised wire nails complete as per direction of
Engineer-in-Charge.
TOTAL FINISHING WORK 3,60,000.00
ROAD WORKS :
22.0 NS Providing and fixing plain Cement concrete Grass Pavers 400x400x60mm on footpath on 450.00 Sqm 770.00 3,46,500.00
roads and filling of earth and grassing with Doop grass in the Grass pavers etc complete
for development of grass
23.0 NS Supplying and laying 40mm stone aggrgate to the reqiured area in required thickness, 50.00 Cum 1,560.00 78,000.00
including all leads and lift.
TOTAL ROAD WORK 4,24,500.00
SANITARY INSTALLATION
24.0 NS Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes
for soil, waste and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including
all The pipes will be supported with threaded GI rods & clamps on 50x50x5 mm slotted
angle. The cost will include all support arrangements. The work includes commissioning of
all pipes lines as per drawings and specifications and as directed by Engineer-in-charge at
site, necessary specials and fittings (confirming to IS : 14735) i.e. bends, tees, junctions
(with or without doors), reducers, WC connectors, couplers, cowels, clamps, rubber rings,
cleanouts, MS holder bat clamp, Y sections, Connections in trap/ manholes etc. fixing at
wall/ceiling/floor level supported by clamp & hangers etc. in concealed / inside duct / under
floor & basement ceiling / external work etc. including chase/ core cutting as required,
excavation and back filiing in all kind of soils, suspended from floor under false ceiling or
embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete
(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) includingcost
of shuttering for proper completion of the work, breaking and making good the walls and
floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS :
5382. The pipes will be supported with threaded GI rods & clamps on 50x50x5 mm slotted
angle.The cost will include all support arrangements. The work includes commissioning of
all pipes lines as per drawings and specifications and as directed by engg-in-charge at
site.
a) NS 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 1,200.00 Mtr. 450.00 5,40,000.00
b) NS 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 700.00 Mtr. 660.00 4,62,000.00
25.0 Providing and fixing UPVC Floor Trap of self cleansing design with CP Jali complete in all
respects including cost of cutting and making good the walls & floors
a) NS Plain Floor Trap (4" Ht) 110*75 mm 150.00 Each 370.00 55,500.00
b) NS Plain Floor Trap (4" Ht) 110*110 mm 350.00 Each 460.00 1,61,000.00
26.0 NS Providing and fixing health faucet with 1 m long flexible tube and wall hook including all 250.00 Each 1,250.00 3,12,500.00
fittings (Jaquar Cat No.ALD 573) or approved equivalent.
27.0 NS Providing and fixing 15mm C.P brass kitchen sink mixer with swinging spout complete. 50.00 Each 2,740.00 1,37,000.00
Including cutting and making good the walls wherever required
C.P. brass mixing fitting Jaquar cat. No. CON-319KN or approved equivalent.
28.0 NS Providing and fixing toilet paper holder including cutting and making good the walls where 200.00 Each 725.00 1,45,000.00
required. Make - Jaquar CA209 or equivalent.
29.0 NS Providing and fixing shower set comparising of following including cutting and making 60.00 Each 5,700.00 3,42,000.00
good the walls where required
i) One No. CP Brass wall mixer bath spout Jaquar Model CON-273 KNUPR or approved
equivalent).
ii) One No. CP Brass over head shower with arm Jaquar Model OHS-1709 + SHA-477 or
approved equivalent).
Shower set as described above
30.0 NS Providing and fixing of C.P. brass soap dish (Make Jaquar Cat No. ACN-1131N or 200.00 Each 620.00 1,24,000.00
equivalent) fixed with C.P. brass screws complete in all respects.
31.0 NS Providing and fixing of C.P. brass 600 mm size towel rail (Make Jaquar Cat No. ACN- 200.00 Each 1,200.00 2,40,000.00
1111NM or equivalent) fixed with C.P. brass screws complete in all respects.
TOTAL SANITARY INSTALLATION 25,19,000.00
WATER SUPPLY
32.0 NS Providing and fixing C.P. brass twin bib cock of approved quality conforming to IS:8931 80.00 Each 550.00 44,000.00
a) 15 mm nominal bore
33.0 NS Providing and fixing forged brass ball valve of brass body with hard chrome plated steel
ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP
threads complete in all respects.
a) NS 25 mm dia 8.00 Each 750.00 6,000.00
b) NS 32 mm dia 10.00 Each 1,280.00 12,800.00
c) NS 40 mm dia 12.00 Each 1,980.00 23,760.00
34.0 NS Providing and fixing lever operated butterfly valve conforming to IS:13095-91 PIN 1.6
including necessary companion flanges, bolts and nuts complete.
a) NS 50 mm dia 6.00 Each 2,510.00 15,060.00
b) NS 65 mm dia 10.00 Each 2,830.00 28,300.00
c) NS 80 mm dia 10.00 Each 3,250.00 32,500.00
d) NS 100 mm dia 4.00 Each 4,220.00 16,880.00
e) NS 150 mm dia 2.00 Each 5,710.00 11,420.00
35.0 NS Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,including cutting and
including trenching and refilling etc..(External work)
a) NS 100 mm dia pipe 250.00 Metre 1,520.00 3,80,000.00
b) NS 150 mm dia pipe 100.00 Metre 2,210.00 2,21,000.00
36.0 NS Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved
quality.
a) NS 100 mm dia pipe 250.00 Metre 52.00 13,000.00
b) NS 150 mm dia pipe 100.00 Metre 72.00 7,200.00
37.0 NS Providing and laying of HDPE pipes confirming to IS: 4984 type PE-80 (6 kg/cm2)
including all fittings wherever required e.g., tees, bends of any degree, couplings,
adapters, plugs, unions etc. and jointing as manufacturer recommondation etc. including
necessary excavation and refilling complete in all respects. (For irrigation water Supply
a) NS 40 mm O.D. Pipe 150.00 Metre 260.00 39,000.00
b) NS 50 mm O.D. Pipe 150.00 Metre 380.00 57,000.00
c) NS 63 mm O.D. Pipe 80.00 Metre 540.00 43,200.00
d) NS 90 mm O.D. Pipe 120.00 Metre 880.00 1,05,600.00
e) NS 110 mm O.D. Pipe 450.00 Metre 1,140.00 5,13,000.00
TOTAL WATER SUPPLY 15,69,720.00
DRAINAGE
38.0 NS Making connection of drain or sewer line with existing manhole including breaking into and 4.00 Each 1,000.00 4,000.00
making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement
mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and
making necessary channels for the drain etc. complete :
ALUMINIUM WORK
39.0 NS Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and 1,800.00 Sqm 1,050.00 18,90,000.00
clerestory windows using wire gauge with average width of aperture 1.4 mm in both
directions with wire of dia. 0.50 mm all complete.
40.0 NS Providing and fixing approved brand and manufacture SS 304 grade D type 1200mm Pull 20.00 Per 3,800.00 76,000.00
Handle with 32mm dia fixed with SS screws etc. complete in all respects as per Pair
manufacturers' specifications & as directed by Engineer-in-charge.
41.0 NS Providing and fixing approved brand and manufacture SS 304 grade D type 300mm Pull 20.00 Per 1,110.00 22,200.00
Handle with 22mm dia fixed with SS screws etc. complete in all respects as per Pair
manufacturers' specifications & as directed by Engineer-in-charge.
42.0 NS Providing and fixing approved brand and manufacture SS 304 grade Patch Lock with 20.00 Each 3,850.00 77,000.00
Cylinder fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
43.0 NS Providing and fixing approved brand and manufacture SS 304 grade Door Closer fixed 24.00 Each 1,750.00 42,000.00
with SS screws etc. complete in all respects as per manufacturers' specifications & as
directed by Engineer-in-charg
44.0 NS Providing and fixing approved brand and manufacture SS 304 grade Mortice handle D type 20.00 Each 950.00 19,000.00
fixed with SS screws etc. complete in all respects as per manufacturers' specifications &
as directed by Engineer-in-charge.
45.0 NS Providing and fixing approved brand and manufacture SS 304 grade Mortice lock with key 20.00 Each 1,240.00 24,800.00
cylinder fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-incharge.
46.0 NS Providing and fixing approved brand and manufacturer SS 304 grade S.S dead lock fixed 50.00 Each 580.00 29,000.00
with SS screws etc. complete in all respects as per manufacturer's specifications & as
directed by Engineer-in-charge.
47.0 NS Extra for providing and fixing toughened glass in aluminium door, window, ventilator 480.00 Sqm 380.00 1,82,400.00
shutters and partitions etc. complete as per the architectural drawings and the directions of
engineer-in-charge.
a) Toughened glass panes of 5.50 mm thickness
48.0 NS Providing and fixing Hand Bar 32mm dia, 1.00 M long of SS 304 grade with SS screws etc. 40.00 Mtr. 410.00 16,400.00
complete in all respects as per specifications & as directed by Engineer-in-charge.
TOTAL ALUMINIUM WORK 23,78,800.00
TUBEWELLS
49.0 NS Providing and fixing 80mm dia GI pipes to IS:1239 heavy class with fittings. 180.00 Metre 915.00 1,64,700.00
50.0 NS Providing and fixing lever operated butterfly valve conforming to IS:13095-91 PIN 1.6 2.00 Each 2,980.00 5,960.00
including necessary companion flanges, bolts and nuts complete.
a) 80mm dia
51.0 NS Providing and fixing C.I. Wafer type flanged non-return valves with bolts, nuts, washers & 2.00 Each 4,650.00 9,300.00
companion flanges complete.
a) 80mm dia
TOTAL TUBEWELLS 1,79,960.00
1.1 2.1 Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of 1,800.00 Cum 45.85 82,530.00
serviceable materials and then disposing of surplus soil, by spreading and neatly
leveling within a lead of 50 m and making up the trenched area to proper levels by
filling with earth or earth mixed with sludge or/and manure before and after flooding
trench with water (excluding cost of imported earth, sludge or manure).
1.2 2.2 Supplying and stacking of good earth at site including royalty and carriage up to 1 km 3,000.00 Cum 332.55 9,97,650.00
(earth measured in stacks will be reduced by 20% for payment).
1.3 2.3 Supplying and stacking at site dump manure from approved source, including carriage
up to 1 km (manure measured in stacks will be reduced by 8% for payment) :
a) 2.3.1 Screened through sieve of I.S. designation 20 mm 300.00 Cum 170.70 51,210.00
b) 2.3.2 Screened through sieve of I.S. designation 16 mm 300.00 Cum 192.05 57,615.00
c) 2.3.2 Screened through sieve of I.S. designation 4.75 mm 300.00 Cum 209.15 62,745.00
1.4 2.7 Fine dressing of the ground 24,000.00 Sqm 2.15 51,600.00
1.5 2.8 Spreading of sludge, dump manure and / or good earth in required thickness as per 900.00 Cum 30.95 27,855.00
direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be
paid separately).
1.6 2.9 Mixing earth and sludge or manure in the required proportion specified or directed by 900.00 Cum 21.35 19,215.00
the Officer-in-charge.
1.7 2.10 Grassing with selection No.1 grass including watering and maintenance of the lawn for
30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing
including supplying good earth, if needed (the good earth if needed shall be paid for
separately).
a) 2.10.1 In rows 5 cm apart in both directions 15,000.00 Sqm 10.40 1,56,000.00
1.8 2.14 Grassing with selection No.1 grass including watering and maintenance of the lawn for
30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing
including supplying good earth, if needed (the good earth if needed shall be paid for
separately).
a) 2.14.1 Holes 1.2 m dia and 1.2 m deep 250.00 Each 236.75 59,188.00
b) 2.14.2 Holes 90 cm dia, and 90 cm deep 250.00 Each 101.40 25,350.00
c) 2.14.3 Holes 60 cm dia, and 60 cm deep 250.00 Each 31.15 7,788.00
d) 2.14.4 Holes 45 cm dia, and 45 cm deep 150.00 Each 13.40 2,010.00
1.0 NS Supply & Planting best quality trees inclusive of cultivation of trees bead to required
depth. All trees / plants to be approved before planting including watering &
maintenance for 180 days.
Trees
i) NS AZADIRACHTA INDICA (Height 10'-12') 60.00 Each 1,162.00 69,720.00
ii) NS ALSTONIA SCHLORIS (Height 10'-12') 20.00 Each 1,162.00 23,240.00
iii) NS CASSIA FISTULA (Height 8'-10') 25.00 Each 1,162.00 29,050.00
iv) NS CHORISIA SPECIOSA (Height 8'-10') 25.00 Each 1,162.00 29,050.00
v) NS FICUS INFECTORIA (Height 8'-10') 30.00 Each 1,162.00 34,860.00
vi) NS GREVILLEA ROBUSTA (Height 8'-10') 250.00 Each 1,162.00 2,90,500.00
vii) NS PLUMERIA ALBA (Height 8'-10') 20.00 Each 1,162.00 23,240.00
viii) NS WASHINGTONIA FILIFERA 1.4 stem 60.00 Each 1,162.00 69,720.00
ix) NS KAGELIA PINNATA (Height 8'-10') 20.00 Each 1,162.00 23,240.00
x) NS MIMOSOPS ELENGI (Height 8'-10') 35.00 Each 1,162.00 40,670.00
xi) NS LAGERSTROEMIA FLOSREGINA (Height 8'-10') 4.00 Each 1,162.00 4,648.00
xii) NS ERICA PALM (Height 6'-8') 4.00 Each 1,162.00 4,648.00
xiii) NS MANGOES (Height 5'-6') 45.00 Each 581.00 26,145.00
Hedges
i) NS CHANDANI (TABERNEMONTANA CORONARIA) (Height 1'-2') 120.00 Each 929.00 1,11,480.00
ii) NS IRISCENE 400.00 Each 697.00 2,78,800.00
iii) NS MELIA AZERDARCH 3.00 Each 1,162.00 3,486.00
1.0 NS-1 Supply,Installation, testing and commissioning of 12-15W LED light fixture fitted Nos 3500 1,720.00 60,20,000.00
with LED lamp including driver etc. as required suitable for ceiling mounting, (Type:
Bajaj:BGSLO sleek surface 15 WH SQ or Surya SLE DLS 12W 6K stellar SQ or
Wipro:LD80-101-XXX-60-SM or Goldwyn or Philips). connections as required as per
site conditions.
2.0 NS-2 Supply,Installation, testing and commissioning of 9-10W LED light fixture fitted with Nos 800 1,130.00 9,04,000.00
LED lamp including driver etc. as required suitable for ceiling mounting, (Type:
Bajaj:BGSLO Sleek Surface 8 WH SQ or Surya SLE DLS 10W 4K Stellar SQ or
Wipro or Philips.) connections as required as per site conditions.
3.0 NS-3 Supply,Installation, testing and commissioning of 1200mm length,1x18-24W,LED Nos 1800 1,074.00 19,33,200.00
type light fixture of comprising frame fitted with LED lamp, including driver etc.
suitable for wall/ceiling mounted as required as per site conditions ( Goldwyn T8-
A20, Wipro LL20-221-XXX-65-NE,Surya SLE BT 20, Bajaj: BCLSB 18WH,
Philips:BN150W LED 20-6500). connections as required as per site conditions.
4.0 NS-4 Supply,Installation, testing and commissioning of 600mm length,1x10-12W,LED Nos 800 790.00 6,32,000.00
type light fixture of comprising frame fitted with LED lamp, including driver etc.
suitable for wall/ceiling mounted as required as per site consitions( Bajaj: BCLSB
10WH, Goldwyn T8-A10 , Wipro LL20-111-XXX-65-NE or Surya SLE BT
10,Philips:BN 150W LED 12S-6500).connections as required as per site conditions.
5.0 NS-5 Supply,Installation,testing and commissioning of 16-20W LED (1 feet X 1 feet) light Nos 600 4,000.00 24,00,000.00
fixture fitted with LED lamp including driver etc. as required suitable for ceiling
mounting, (Type: Bajaj:BCTBLS 18 ZT WH or Goldwyn or Wipro or Surya SLE DS
20 11S or Philips). connections as required as per site conditions.
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
7.0 NS-7 Supply,Installation,testing and commissioning of 30-38W LED (2 feet X 2 feet) light No. 100 5,878.00 5,87,800.00
fixture fitted with LED lamp including driver etc. as required suitable for ceiling
mounting, (Type: Bajaj:BZSSQL 36W WH or Goldwyn or
Wipro:CRCO10SO38HP57G1 or Surya SLE DS 36 22S or Philips:SM365C LED-33-
6500 PSE-OD (white)). connections as required as per site conditions.
8.0 NS-8 Supply,Installation, testing and commissioning of 6-10W LED light fixture fitted with Each 450 1,130.00 5,08,500.00
LED lamp including driver etc. as required for wall mounting, (Type: Bajaj / Wipro:-
Garnet wall light 7W/Philips: 35022 oriel LED Wall light 12W ).connections as
required as per site conditions.
9.0 NS-9 Supply, Installation, Testing and Commissioning of 20W LED PENDANT LIGHT Each 10 11,740.00 1,17,400.00
.Similar to Philips 31145/31 Mesa
10.0 NS-10 Supply, Installation, Testing and Commissioning of 24W LED DECORATIVE Each 80 11,740.00 9,39,200.00
PENDANT/SURFACE MOUNTED LIGHT.Similar to Philips 31145/31 Mesa.
11.0 NS-11 Supply,Installation, testing and commissioning of 6-10W LED bulk head light fixture, Each 360 1,130.00 4,06,800.00
fitted with LED lamp, including driver etc. as required for ceiling/wall mounting,
(Type: Bajaj:BIBWP 10W LED , Philips: WT202W LED6S PSU ,Wipro LW03-850-
XXX-57-XX, Surya :SLE BLH 10W) connections as required as per site conditions.
12.0 NS-12 Supply,Installation, testing and commissioning of 8W LED fixture, fitted with LED No. 120 1,130.00 1,35,600.00
lamp, including driver etc. as required for recess mounting, (Type: Bajaj: BGSLO
sleek 8W SQ, Goldwyn ,Wipro: LD81-530-XXX-60-XX,Surya: SLE DLR 10W 6K
stellar SQ ). connections as required as per site conditions.
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
14.0 NS-14 Supply,Installation, testing and commissioning of 36-42W weather proof LED No. 20 6,000.00 1,20,000.00
fixture, fitted with LED lamp, including driver etc. as required for recess/ceiling
mounting, (Type: Bajaj:-BIPC 40WLED, Goldwyn WP01 12 ,Wipro LE20-491-XXX-
57-XX, Surya SLE BJPC 218 LED),colour temp 6500K connection as per site
conditions.
15.0 NS-15 Supply,Installation, testing and commissioning of 100W LED flood light type No. 20 13,020.00 2,60,400.00
luminaire housing shall be of corrosion free, pressure die cast aluminium,
comprising of toughened clear front glass, LED chips, mounted on suitable designed
aluminium heat sink with high thermal conductivity for better heat dissipation, fitted
with integral drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket
lining complying to IP 65 class of protection.(Type: Bajaj: BARFEG 100W LED or
Goldwyn XB 01 51 or Wipro LR18-971-XXX-57-XX or Surya SLE FL 100W IP65
LUMOS). connections as required as per site conditions.
16.0 NS-16 Supply,Installation, testing and commissioning of 160W LED flood light type No. 20 22,340.00 4,46,800.00
luminaire housing shall be of corrosion free, pressure die cast aluminium,
comprising of toughened clear front glass, LED chips, mounted on suitable designed
aluminium heat sink with high thermal conductivity for better heat dissipation, fitted
with integral drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket
lining complying to IP 65 class of protection.(Type: Bajaj: BARFEG 160W LED or
Goldwyn XB 01 50 or Wipro LF08-172-120-57-XX or Surya SLE FL 160W IP65
LUMOS). connections as required as per site conditions.
17.0 NS-17 Supply,Installation, testing and commissioning of IP 68 ,18-20W LED underwater No. 10 6,940.00 69,400.00
luminaire for swimming pool/splash pool, suitable for use with AC 12V with provision
of loop in & loop out , complete as required including driver, 230/12V AC
transformer,Junction box,etc including connections as required.
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
19.0 NS-19 Supply of 225 mm sweep Exhaust fan(metal body) suitable for single phase, No. 200 2,000.00 4,00,000.00
230V,speed preferably in the range of 1350-1450 rpm rpm, AC supply complete
with motor, capacitor, guard, mounting brackets, all accessories of
(Bajaj/Crompton/Khaitan/Orient) make.
20.0 NS-20 Supply of 300 mm sweep Exhaust fan(metal body) suitable for single phase, No. 200 2,200.00 4,40,000.00
230V,speed preferably in the range of 1350-1450 rpm , AC supply complete with
motor, capacitor,guard, mounting brackets, all accessories of
(Bajaj/Crompton/Khaitan/Orient) make.
21.0 NS-21 Supply of 450 mm sweep Exhaust fan(metal body) suitable for single phase, No. 15 5,500.00 82,500.00
230V,speed 930-980 rpm, AC supply complete with motor, capacitor,guard,
mounting brackets, all accessories of (Bajaj/Crompton/Khaitan/Orient) make.
22.0 NS-22 Supply and fixing of 400 mm sweep Bracket fan suitable for single phase, 230V, AC No. 25 4,000.00 1,00,000.00
supply complete with motor, capacitor mounting brackets, including all accessories
swing & speed pull-cord control and of (Bajaj/Crompton/Khaitan/Orient) make
including connection as required.
23.0 NS-23 Supply of Ceiling fan with 600mm sweep, double ball bearing motor, capacitor, three Nos 25 2,800.00 70,000.00
MS blades die cast Al housing in stove enameled white with, suspension rod
including all accessories of (Bajaj/Crompton/Khaitan/Orient) make.
24.0 NS-24 Supply of Ceiling fan with 1200mm sweep, double ball bearing motor, capacitor, Nos 1500 3,000.00 45,00,000.00
three MS blades die cast Al housing in stove enameled white with, suspension rod
including all accessories of (Bajaj/Crompton/Khaitan/Orient) make.(5 star rated)
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
26.0 NS-26 Supplying, installation, testing & Commissioning of Self contained Each 30 2,880.00 86,400.00
emergency light units 1x9 watt double sided for wall / ceiling mounting with
suspension / mounting kit, lamps, inbuilt standby battery (for 2 hours backup) and
battery charger etc. in suitable as approved make.
h 20 Kva UPS operating in parallel redundant configuration (for Emergency No. 4 7,07,500.00 28,30,000.00
Lighting,Work Stations, Fire Alarm, Server and CCTV). (Academic Block)
28.0 NS-28 Supplying and fixing 63 A, 415 V, TPN Industrial type socket outlet, with 4 pole and Each 150 4,342.00 6,51,300.00
earth, metal enclosed plug top alongwith 63 A, C curve, TPMCB, in sheet steel
enclosure, on surface or in recess, with chained metal cover for the socket out let
and complete with connections, testing and commissioning etc. as required.
29.0 NS-29 Supplying and fixing 125 A, 415 V, TPN Industrial type socket outlet, with 4 pole and Each 100 6,947.00 6,94,700.00
earth, metal enclosed plug top alongwith 125 A, C curve, TPMCCB, in sheet steel
enclosure, on surface or in recess, with chained metal cover for the socket out let
and complete with connections, testing and commissioning etc. as required.
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
30.0 NS-30 Supplying and installing following size of Ladder type M.S. cable trays with
perforation not more than 17.5%, in convenient sections, joined with connectors,
suported from the wall with M.S. supprots including bolts & nuts, painting supprots
etc as required.
a 600mm wide Metre 100 1,302.00 1,30,200.00
b 450mm wide Metre 200 1,042.00 2,08,400.00
c 300mm wide Metre 200 781.00 1,56,200.00
31.0 NS-31 Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet)
race ways for electrical & LV wiring including neoprene gasket in joints, cutting
the floor & jaming the race way / hanging in ceiling, supporting arrangement
as approved by consultant / architect with all necssary hard ware (including
civil work) as per site requirement. The thickness of raceway & cover shall be as
per technical specification.
31.1 a 75 mm wide x 40 mm deep. Meter 400 487.00 1,94,800.00
31.2 b 100 mm wide x 50 mm deep. Meter 300 774.00 2,32,200.00
31.3 c 150 mm wide x 50mm deep. Meter 75 911.00 68,325.00
31.4 d 200 mm wide x 75 mm deep. Meter 60 1,366.00 81,960.00
31.5 e 250 mm wide x 75 mm deep. Meter 50 1,671.00 83,550.00
31.6 f 300 mm wide x 100 mm deep. Meter 50 2,171.00 1,08,550.00
32.0 NS-32 Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for
electrical & LV wiring including, cutting the floor & jaming the junction box /
hanging in ceiling, supporting arrangement as approved by consultant / architect
with all necssary hard ware (including civil work).(Junction box to be provided
as per drawing/ as per site requirement & as per specification). The thickness of
junction box shall be a as per thechnical specification.
32.1 a 100 mm wide x 50 mm deep. Set 80 424.00 33,920.00
32.2 b 150 mm wide x 50 mm deep. Set 50 530.00 26,500.00
32.3 c 200 mm wide x 50 mm deep. Set 30 672.00 20,160.00
32.4 d 250 mm wide x 100 mm deep. Set 25 824.00 20,600.00
32.5 e 300 mm wide x 100 mm deep. Set 10 1,476.00 14,760.00
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
34.0 NS-34 Supply, fixing and testing of 30 pair solderless telephone tag block in 1.6mm thick No. 50 1,300.00 65,000.00
sheet pre galvanised MS box duly painted by enamel paint on primer coat with
hinged and locking arrangement of suitable size for cables including termination of
cables etc. complete as required
35.0 NS-35 Supply, fixing and testing of 10 pair solderless telephone tag block in 1.6mm thick No. 50 800.00 40,000.00
sheet pre galvanised MS box duly painted by enamel paint on primer coat with
hinged and locking arrangement of suitable size for cables including termination of
cables etc. complete as required
36.0 NS-36 Supply, fixing and testing of 100 pair solderless telephone tag block in 1.6mm thick No. 10 3,000.00 30,000.00
sheet pre galvanised MS box duly painted by enamel paint on primer coat with
hinged and locking arrangement of suitable size for cables including termination of
cables etc. complete as required
37.0 NS-37 Supplying and drawing of 30 pair 0.5 sq mm FRLS PVC insulated annealed Metre 1000 80.00 80,000.00
copper conductor, unarmored telephone cable in the existing surface/ recessed
steel/ PVC conduit as required.
38.0 NS-38 Supplying and drawing of 10 pair 0.5 sq mm FRLS PVC insulated annealed Metre 1000 40.00 40,000.00
copper conductor, unarmored telephone cable in the existing surface/ recessed
steel/ PVC conduit as required.
39.0 NS-39 Supplying and fixing following rating, three pole, 415 volts, MCB,16KA, in the existing
MCB DB complete with connections, testing and commissioning etc. as required. "C"
curve
a 40 amps Each 80 1,042.00 83,360.00
b 63 amps Each 70 1,302.00 91,140.00
S.No. N.S. item Description of Item Unit Qty. Rate (Rs) Amount (Rs)
Earthing
1.0 5.2 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing Each 30 3,672.00 1,10,160.00
masonry enclosure with cover plate having locking arrangement and watering pipe etc. with
charcoal/ coke and salt as required
2.0 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and Set 30 4,327.00 1,29,810.00
providing masonry enclosure with cover plate having locking arrangement and watering pipe
of 2.7 metre long etc. with charcoal/ coke and salt as required.
3.0 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and Set 10 8,289.00 82,890.00
providing masonry enclosure with cover plate having locking arrangement and watering pipe
of 2.7 metre long etc. with charcoal/ coke and salt as required.
4.0 5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, Meter 300 85.00 25,500.00
including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing
shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
5.0 5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. Meter 200 351.00 70,200.00
pipe from earth electrode including connection with G.I. nut, bolt,
spring, washer excavation and re-filling etc. as required.
6.0 5.14 Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as Meter 500 698.00 3,49,000.00
required.
7.0 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as Meter 500 129.00 64,500.00
required
8.0 5.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with Meter 500 23.00 11,500.00
existing surface/ recessed conduit/ submain wiring/ cable as required.
9.0 5.20 Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as Meter 150 1,283.00 1,92,450.00
required.
MV cable laying
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
III EXTERNAL ELECTRIFICATION WORKS( ERECTION) DSR based
10.0 7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV -
grade of following size direct in ground including excavation, sand cushioning, protective
covering and refilling the trench etc as required.
a 7.1.1 Upto 35 sq. mm Meter 2800 206.00 5,76,800.00
b 7.1.2 Above 35 sq. mm and upto 95 sq. mm Meter 1800 214.00 3,85,200.00
c 7.1.3 Above 95 sq. mm and upto 185 sq. mm Meter 1800 223.00 4,01,400.00
d 7.1.4 Above 185 sq. mm and upto 400 sq. mm Meter 1800 248.00 4,46,400.00
11.0 7.2 Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV -
grade of following size direct in ground in the same trench in one tier horizontal formation
including excavation, sand cushioning, protective covering and refilling the trench etc as
required.
a 7.2.1 Upto 35 sq. mm Meter 2800 141.00 3,94,800.00
b 7.2.2 Above 35 sq. mm and upto 95 sq. mm Meter 500 149.00 74,500.00
c 7.2.3 Above 95 sq. mm and upto 185 sq. mm Meter 500 158.00 79,000.00
d 7.2.4 Above 185 sq. mm and upto 400 sq. mm Meter 1400 183.00 2,56,200.00
12.0 7.5 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of
following size in the existing RCC/ HUME/ METAL pipe as required.
a 7.5.1 Upto 35 sq. mm Metre 650 18.00 11,700.00
b 7.5.2 Above 35 sq. mm and upto 95 sq. mm Metre 1400 28.00 39,200.00
c 7.5.3 Above 95 sq. mm and upto 185 sq. mm Metre 500 37.00 18,500.00
d 7.5.4 Above 185 sq. mm and upto 400 sq. mm Metre 500 65.00 32,500.00
13.0 7.6 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of
following size in the existing masonry open duct as required.
a 7.6.1 Upto 35 sq. mm Metre 550 14.00 7,700.00
b 7.6.2 Above 35 sq. mm and upto 95 sq. mm Metre 350 22.00 7,700.00
c 7.6.3 Above 95 sq. mm and upto 185 sq. mm Metre 100 31.00 3,100.00
d 7.6.4 Above 185 sq. mm and upto 400 sq. mm Metre 900 56.00 50,400.00
14.0 7.7 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV
grade of following size on wall surface as required.
a 7.7.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Metre 150 25.00 3,750.00
b 7.7.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) Metre 550 72.00 39,600.00
c 7.7.3 Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) Metre 50 84.00 4,200.00
d 7.7.4 Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) Metre 500 120.00 60,000.00
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
III EXTERNAL ELECTRIFICATION WORKS( ERECTION) DSR based
15.0 7.8 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV -
grade of following size on cable tray as required.
a 7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Meter 5200 21.00 1,09,200.00
b 7.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) Meter 800 49.00 39,200.00
c 7.8.3 Above 95 sq. mm and upto 185 sq. mm (clamped with 40/25x3mm MS flat clamp) Meter 500 61.00 30,500.00
d 7.8.4 Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) Meter 500 96.00 48,000.00
16.0 7.9 Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : Each 200 333.00 66,600.00
4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm
X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.
HT CABLE LAYING:
17.0 8.7 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 33 KV
grade of following size in the existing RCC/HUME/ METAL pipe as required.
a 8.7.2 Above 120 sq. mm and upto 400 sq. mm Meter 450 68.00 30,600.00
18.0 8.8 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 33KV
grade of following size in the existing masonry open duct as required.
a 8.8.2 Above 120 sq. mm and upto 400 sq. mm Meter 50 58.00 2,900.00
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
III EXTERNAL ELECTRIFICATION WORKS( ERECTION) DSR based
n 9.1.34 4 X 25 sq. mm (28mm) Each 30 258.00 7,740.00
21.0 10.8 Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete
with all accessories including lugs suitable for following size of 3 core, XLPE aluminiumconductor
cable of 33 kV grade as required.
a 10.8.3 240 sq. mm Each 1 21,224.00 21,224.00
23.1 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm -
internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23
kg and weight of frame 15 kg) :
19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 50 8,063.00 4,03,150.00
-
TOTAL: EXTERNAL ELECTRIFICATION WORKS( ERECTION) DSR based 54,70,696.00
2.0 NS-2 33KV, SINGLE BREAKER PANEL- (INDOOR TYPE) Set 1 9,15,000.00 9,15,000.00
33 KV VCB Single Breaker Panel Board as Icomming / Outgoing shall be metal clad floor mounting
complete as per specification and as described.
630 A VCB Breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV rated, totally enclosed,
air insulated metal clad housing, floor mounting, horizontal isolation, vermin proof, fully
interlocked horizontal drawout type having isolation features and control devices complete with the
following.
Manually and motor operated, spring charged (release closing mechanism) trip free type, triple
pole truck mounted draw out, VCB, incorporating mechanical as well as electrical ON/OFF
indication. Spring charge/discharge mechanical indication"OFF" push buttons for emergency trip
(shrouded) test/service position limit switches with 6 NO/6NC breaker auxilliary contacts in
service position, 24 Volts DC shunt trip coil and strip heater to prevent moisture absorption.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
relevant IS Standards and complete as required.
One no. numerical microprocessor based three phase over current (IDMT element) with earth fault
relay with instantaneous elements.
1 No. Anti Pumping device.
1 No. Circuit breaker control switch for electrical (T/N/C).
1 No. limit switch for test & service position.
1 No. Voltmeter (0-36KV) with selector switch. (96mm square).
1 No. Ammeter (0-100Amp) with selector switch. (96mm square).
1 No. electronic type digital energy analyser having 30 days memory and parameters of KW,
KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.
1 Set of following indicating lamps.
Red, Yellow & Blue for phase indication.
Amber for Trip indication.
Red `ON' Green `OFF'
Spring charge indication.
Auto trip indication.
1 No. hooter with hooter acceptance and reset push button.
1 No. master trip relay. (Electromechanical Type)
1 No. Over voltage relay. (Static Type)
1 No. Under voltage relay. (Static Type)
12 window announciator for all electrical and transformer fault.
1 No.Trip ckt supervision relay (Electromechanical Type)
1 Set of fuses, ferrules, wiring etc. as required.
1 Set of battery and battery charger suitable for 12 Hour backup for all control supply.
2 No. control Transformer of 1KVA for giving supply to indication lamps etc having 33 KV/415-
230V AC rating epoxy cast resin dry type Transformer. The connection for control transformer
shall be taken from the cable side before the circuit breaker tapping.
Note: All spare contacts of breaker or any other equipment inside the breaker shall be
wired upto the outgoing terminal strip with appropriate ferrules / coding. The terminal strip
rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum
size strip suitable for 4/6sqmm.
3.0 NS-3 33 KV HT VCB Three Breaker Panel Board (Indoor Type) (1 Incomming + 4 Outgoing) Set 1 28,80,000.00 28,80,000.00
33 KV Three Breaker Vacuum Circuit Breaker Panel Board as 1 Incomming & 4 Outgoing
shall be metal clad floor mounting complete as per specification and as described.
630 A Vacuum circuit breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV rated, totally
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
enclosed,air insulated metal clad housing, floor mounting, horizontal isolation, vermin proof,
fully interlocked horizontal drawout type having isolation features and control devices
complete with the following.
Manually and motor operated, spring charged (release closing mechanism) trip free type,triple
pole truck mounted draw out, vacuum circuit breaker, incorporating mechanical as well as
electrical ON/OFF indication. Spring charge/discharge mechanical indication"OFF" push buttons
for emergency trip (shrouded) test/service position limit switches with 6 NO/6 NC breaker
auxilliary contacts in service position, 24 Volts DC shunt trip coil and strip heater to prevent
moisture absorption.
INCOMING PANEL - 1 NO.
1 No 630 A Vacuum circuit breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV
rated, totally enclosed,air insulated metal clad housing, floor mounting, horizontal isolation,vermin
proof,fully interlocked horizontal drawout type having isolation features and control devices
complete with the following:
3 No. Single Phase double core current transformer 120/5 Amp epoxy cast insulated class of
insulation E.
Core 1-15VA burden class 1.0 for metering.
Core 2-15VA burden class 5P20 for protection.
P.T's of 33KV/1.732, 110V/1.732, 100VA with suitable rating H.T. & L.T. fuse conforming to
relevant IS Standards and complete as required.
One no. numerical microprocessor based three phase over current (IDMT element) (2 O/C+1E/F)
with earth fault relay with instantaneous elements.
1 No. Anti Pumping device.
1 No. Circuit breaker control switch for electrical (T/N/C).
1 No. limit switch for test & service position.
1 No. Voltmeter (0-36KV) with selector switch. (96mm square).
1 No. Ammeter (0-100Amp) with selector switch. (96mm square).
1 No. electronic type digital energy analyser having 30 days memory and parameters of KW,
KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.
1 Set of following indicating lamps.
Red, Yellow & Blue for phase indication.
Amber for Trip indication.
Red `ON' Green `OFF'
Spring charge indication.
Auto trip indication.
1 No. hooter with hooter acceptance and reset push button.
1 No. master trip relay. ( Electromechanical Type )
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 No.Trip ckt supervision relay. (Electromechanical Type )
600A color coded heat shrinkable sleeved TP Copper busbar of 350 MVA fault rating.
1 Set of fuses, ferrules, wiring etc. as required.
1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete as required.
2 No. control Transformer of 1KVA for giving supply to indication lamps etc having 33KV/415-230V
AC rating epoxy cast resin dry type Transformer. The connection for control transformer shall be
taken from the cable side before the circuit breaker tapping.
Note: All spare contacts of breaker or any other equipment inside the breaker shall be
wired upto the outgoing terminal strip with appropriate ferrules / coding. The terminal strip
rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum
size strip suitable for 4/6sqmm.
OUTGOING PANEL - 4 NO. (Each outgoing feeder shall have following)
1 No 630 A Vacuum circuit breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV
rated, totally enclosed,air insulated metal clad housing, floor mounting, horizontal isolation,vermin
proof,fully interlocked horizontal drawout type having isolation features and control devices
complete with the following:
3 No. Single Phase double core current transformer 60/5 Amp epoxy cast insulated class of
insulation E.
Core 1-15VA burden class 1.0 for metering.
Core 2-15VA burden class 5P20 for protection.
One no. numerical microprocessor based three phase over current (IDMT element) (2 O/C+1E/F)
with earth fault relay with instantaneous elements.
1 No. Anti Pumping device.
1 No. Circuit breaker control switch for electrical (T/N/C).
1 No. limit switch for test & service position.
1 No. Voltmeter (0-36KV) with selector switch. (96mm square).
1 No. Ammeter (0-50Amp) with selector switch. (96mm square).
1 No. electronic type digital energy analyser having 30 days memory and parameters of KW,
KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.
1 Set of following indicating lamps.
Red, Yellow & Blue for phase indication.
Amber for Trip indication.
Red `ON' Green `OFF'
Spring charge indication.
Auto trip indication.
1 No. hooter with hooter acceptance and reset push button.
1 No. master trip relay. ( Electromechanical Type)
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 No.Trip ckt supervision relay (Electromechanical Type)
1 Set of fuses, ferrules, wiring etc. as required.
3 No. VAA33 auxiliary relay for transformer fault, alarm and trip.
12 Annunciator window for all electrical and transformer fault.
Note: All spare contacts of breaker or any other equipment inside the breaker shall be
wired upto the outgoing terminal strip with appropriate ferrules / coding. The terminal strip
rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum
size strip suitable for 4/6sqmm.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
vibration isolation pads, extended cable termination box, grouting bolts, first charge of engine oil,
gear oil, high speed diesel oil, 24 volt maintenance free chargeable battery set with Trickle / Boost
Battery charger, interface card for BMS connectivity complete as required of rating 415 Volts, 3
phase, 50 Hz. AC alternator coupled to Diesel Engine complete with all accessories. NOC from
concerned goverment authority for installation and operation of D.G. set shall be taken by
contractor conforming to CPCB norms
7.1 a 500 KVA D.G. Set with suitable capacity of day oil fuel Tank with electronic governer with Set 1 28,80,000.00 28,80,000.00
electronic control panel for sychronizing.
7.2 b 250 KVA D.G. Set with suitable capacity of day oil fuel Tank with electronic governer with Set 1 14,20,000.00 14,20,000.00
electronic control panel for sychronizing.
Insulation and cladding for exhaust ducting inside genset room area and outside using 75 Sq. M 20 1,345.00 26,900.00
mm thick rockool of density 144 Kg/ M3 & 24 SWG Aluminium Sheet.
8.3 c MS structure for supporting of DG emission, exhaust piping with RCC foundation and in cable Kg. 1500 43.00 64,500.00
trench for cable support etc. complete in all respect.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
Continuously tapered multifaceted and polygonal cross section High mast as per detailed
specification & details given
a) 1 or 2 sections having suitable sectional length with slip joints between sections without any
circumpherencial welding.
b) Double drum winch with separate handle for motorised and manual operation of winch with a
torque limiting device for safe docking of carriage.
c) Raising/lowering type lantern carriage designed to carry 08 nos luminaries; control gear box,
junction box and top pulley assemble with weather proof cover.
d) Necessary suitable length for lowering & rising of lantern carriage of stainless steel wire ropes of
7/19 construction(with minimum 6mm dia) and multicore flexible copper power cable
e) Hinged service door in base section base plate earthing terminal.
f) Suitable arrangement for supply distribution with termination of suitable size underground cable
in high mast.
g) Complete with other provision for execution in the confirmation with detailed technical
specifications.
h) Lightning conductor finial made of 25mm dia 300 mm long G.I.tube having single prong.
i) Integral single power tool (electrical) for lowering & raising of high mast with separate manually
operated system.
j) Anchor plate, templates, foundation bolts manufactured from special steel along with nuts
10.1 a 16 meter High mast (two sections) Each 1 86,420.00 86,420.00
10.2 b 12 meter high mast (one sections) Each 5 65,290.00 3,26,450.00
10.3 c 250W +/-5W LED Flood Light Luminaire with System lumen output more than 25000 lm with Each 40 51,500.00 20,60,000.00
Special Optical Grade Borosilicate Glass Lens having distribution of option of 60/90/120 Deg Beam
Angle. LED Flood Light Shall be made up of Die cast aluminium housing with seperate LED &
Driver componet. The Luminaire shall be complete IP 65 for optical & Control Gear Compartment.
The Optical compartment shall be covered with heat resistant toughned glass for safety and shall
have excelent thermal management with specially designed integral cooling fins on housing. The
LEDs used in the product shall be reputed make like Lumiled USA/Cree USA/Citizen Japan/Nichia
Japan only. The Luminaire shall have multiple COB Type high efficiency LEDs to get sufficient light
O/P from Luminaire having LED Chip Lumen of more than 120 Lm/W. The LED shall be tested
with LM80-08 standard with useful life of 50000 Hrs. at L70. The LEDs used in Flood Light shall
have CCT of ANSI Bin 5000K with CRI of 70. LEDs used must be tested as per EN62471 for
Photobiological Safety of humans, The LED flood Light shall be of Integral type. The input voltage
range shalll be 100V to 300V. The LED Driver shall with Over voltage, Under Voltage, Short Circuit
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
10.4 d Dust vermin and weather proof out door compartmentalized feeder pillar of suitable size made of Each 7 38,800.00 2,71,600.00
2.0 mm M.S. sheet complete with the following:-
a) Canopy at top, IP 55
b) Hinged door open able on both side with heavy duty locking system.- 02 nos
c) Base frame with detachable cover on all sides made out of 2.0 mm steel sheet.
d) Legs of suitable length make out of 40mm x 40mm x 6mm angle iron including grouting the legs
in 1:2:4 CC (1 Cement 2 coarse sand 4 stone aggregate of 40 mm nominal size).
e) Knock out holes at bottom for cable entry
f) Earthing stud- 02 nos
g) Powder coated of approved shade.
h) 63 amps TPN MCB, 16K breaking capacity- 01 No,
i) 40 Amps TP air brake contactor
j) 24 hour Electronic timer 01 No
k) Heavy duty godown lock- 02 Nos.
l) power tool control with with 02 nos 09 Amps contactors
m) raise/lower push button
n) Termination incoming/outgoing cables with suitable sizes of ferrules & compression gland
o) O/L and SPP motor protection.
11.0 NS-11 Flange mounted hot dip Galvanized Octangonal Pole of 7 Mtr height made from 3.5 mm thick HT Each 60 11,700.00 7,02,000.00
Steel plate, having top dia-90mm & bottom dia of 155 mm complete with window with flash cover at
a height of 500mm from the base for cable termination block etc and galvanized base plate of size
220 mm x 220mm x 12 mm thick on existing cement concrete pedestal as required including
supplying and fixing the following in the window box provided for cable termination as per direction
of engineer incharge:-
a) Supplying and fixing 6mm thick laminated mounted sheet inside the window mounted on and
including providing and welding 02 nos G.I. strips 4mm thick of suitable length and having suitable
size tapped holes as reqd.
b) Supplying and fixing 63 Amps terminal block, suitable for 10 sq.mm conductor- 04 nos &
shorting links- 05 nos. on DIN Channel including providing. And fixing DIN Channel of suitable
length- 01 nos on the existing laminated sheet.
c) Supplying and fixing 6 Amps, SPMCB, C characteristics curve- 02 nos, Earth stud 02 nos,
welded at suitable height, washers, springs washers & nuts.
d) M - 20 reinforced cement concrete foundation of size 550mm x 550mm wide and 1200 mm
deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of
cold twisted bars of 12 mm dia- 1200 mm long (approx)- 08 nos and reinforcement ring of cold
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
12.0 NS-12 Flange mounted hot dip Galvanized Octangonal Pole of 9 Mtr height made from 4 mm thick HT Each 28 19,600.00 5,48,800.00
Steel plate, having top dia-90mm & bottom dia of 185 mm complete with window with flash cover at
a height of 500mm from the base for cable termination block etc and galvanized base plate of size
220 mm x 220mm x 12 mm thick on existing cement concrete pedestal as required including
supplying and fixing the following in the window box provided for cable termination as per direction
of engineer incharge:-
a) Supplying and fixing 6mm thick laminated mounted sheet inside the window mounted on and
including providing and welding 02 nos G.I. strips 4mm thick of suitable length and having suitable
size tapped holes as reqd.
b) Supplying and fixing 63 Amps terminal block, suitable for 10 sq.mm conductor- 04 nos &
shorting links- 05 nos. on DIN Channel including providing. And fixing DIN Channel of suitable
length- 01 nos on the existing laminated sheet.
c) Supplying and fixing 6 Amps, SPMCB, C characteristics curve- 02 nos, Earth stud 02 nos,
welded at suitable height, washers, springs washers & nuts.
d) M - 20 reinforced cement concrete foundation of size 550mm x 550mm wide and 1200 mm
deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of
cold twisted bars of 12 mm dia- 1200 mm long (approx)- 08 nos and reinforcement ring of cold
13.0 NS-13 72W LED street light type luminaire housing shall be of corrosion free, pressure die cast Each 60 9,900.00 5,94,000.00
aluminium, comprising of polycarbonate cover or better, LED chips, mounted on suitable designed
aluminium heat sink with high thermal conductivity for better heat dissipation, fitted with integral
drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket lining complying to IP
65/66 class of protection (Type: Philips: BRP410 LED CW 072 MR FG S1 PSU GR or Bajaj:
BRTFG 72W LED or Crompton or Wipro: LR02-781-XXX-57-XX or Surya: SLE UL 72W IP66
LXN) connections as required as per technical specification.
14.0 NS-14 90W LED street light type luminaire housing shall be of corrosion free, pressure die cast Each 28 12,800.00 3,58,400.00
aluminium, comprising of polycarbonate cover or better, LED chips, mounted on suitable designed
aluminium heat sink with high thermal conductivity for better heat dissipation, fitted with integral
drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket lining complying to IP
65/66 class of protection (Type: Bajaj:BRTFG 90W LED or Wipro:LR02-102-XXX-57-XX or
Surya: SLE UL 90W IP66 LXN or Goldwyn: XS 04 19 Jupiter) connections as required as per
technical specification.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
15.0 NS-15 Decorative lighting pole 4000 mm height, 4X 100W LED flood light type luminaire housing Each 1 60,470.00 60,470.00
shall be of corrosion free, pressure die cast aluminium, comprising of toughened clear front glass,
LED chips, mounted on suitable designed aluminium heat sink with high thermal conductivity for
better heat dissipation, fitted with integral drivers, stainless steel toggle clips & neoprene/ synthetic
rubber gasket lining complying to IP 65 class of protection.(Type: Philips:-BVP410 LED 107CW HE
NB FG S3 XT or Bajaj: BARFEG 100W LED or Crompton LSFO-72-CDL or Wipro LR18-971-XXX-
57-XX or Surya SLE FL 100W IP65 LUMOS). connections as required as per site conditions.
16.0 NS-16 Solar street light system shall be SPV module, based White Light Emitting Diode (W-LED) (20W) Set 20 39,740.00 7,94,800.00
including all fittings and fixtures, battery and mounted on a pole of suitable height (minimum 4.0
mt), charger controller, protection, including foundation, earthing with 5 years comprehensive
warranty with complete as required. The broad details as specify : PV Module - 75 Wp, module
efficiency should not be less than 13.5 % with IEC 61215 certified, Battery - Lead acid Tubular
Flooded / VRLA , 12V- 75 AH @ C/10, Duty Cycle - Dusk to dawn. The details shall be as per
specification as specified.
17.0 NS-17 3.0Mtr, 65mm dia GI pole with finished powder coated, base plate 300 x 300 x 3mm GI reducer & No. 45 12,090.00 5,44,050.00
nipple for mounting the fitting, 4 nos. foundation bolts. It consists of junction box shall be inside the
pole with suitable MCB control & loop-in loop-out arrangement (Make : BIS Approved make)
complete as required as per technical specification.
18.0 NS-18 30/40W LED Post Top Lantern type luminaire housing shall be of corrosion free, cast aluminium No. 45 8,200.00 3,69,000.00
spigot, comprising of acrylic diffuser, LED chips, mounted on suitable designed aluminium heat
sink with high thermal conductivity for better heat dissipation, fitted with integral drivers, stainless
steel toggle clips & neoprene/ synthetic rubber gasket lining complying to IP 65 class of protection
(Type: Philips or Bajaj: BGCL 40W LED or Crompton: LPTO-40/CDL or Wipro or Surya: SLE PT
30W-GMP) connections as required as per technical specification.
19.0 NS-19 30/40W LED Gate light fixture with necessary driver, lamp, connections, wiring & etc. complying to No. 10 4,200.00 42,000.00
IP 65 class of protection complete as required. (Philips or Bajaj:-BGCS 40W LED or Crompton or
Wipro: or Surya: SLE PT 30W-ETP)
20.0 NS-20 9W LED spike light fixture with necessary driver, lamp, connections, mounting arrangement-spike, No. 20 4,300.00 86,000.00
wiring & etc. complying to IP 65 class of protection complete as required. (Philips:-BGP311 3xLED-
HP/WW 220-240V 12 1N or Bajaj:-BGSBL 9W LED WW or Crompton: or Wipro:LF05-600-055-27-
XX or Surya: SLE SPLR 9W)
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
21.0 NS-21 9-10W LED Bollard light fixture with necessary driver lamp, connections, wiring & etc. complying to No. 60 3,800.00 2,28,000.00
IP 65 class of protection complete as required. (Philips:BCP150 LED150/WW PSU 220-240V
7043 or Bajaj:BGBOL 605 9W LED or Crompton or Wipro: CRLA11008HP57-08 or Surya: SLE
BL 10W-550)
22.0 NS-22 3/4W LED Step light fixture with necessary driver, lamp, connections, mounting arrangement - No. 48 1,900.00 91,200.00
wiring & etc. complying to IP 65 class of protection, complete as required. (Philips:- BWG150
LED50/WW PSU 220-240V IP67 7043 or Bajaj: BLSGV 4W or Crompton: or Wipro:-LT54-002-
XXX-WW-XX or Surya: SLE STL 3W)
23.0 NS-23 IP 68 ,18-20W LED underwater luminaire for swimming pool/splash pool, suitable for use with AC No. 5 4,300.00 21,500.00
12V with provision of loop in & loop out , complete as required including driver, 230/12V AC
transformer,Junction box,etc including connections as required.
24.0 NS-24 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required Meter 600 206.00 1,23,600.00
26.0 NS-26 1.1KV grade multicore aluminium conductor XLPE insulated and PVC sheathed armoured cable
conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule
by architect / consultant) of following sizes.
26.1 a 3.5 core, 300 sq.mm. Meter 3600 1,502.00 54,07,200.00
26.2 b 3.5 core, 240 sq.mm. Meter 900 1,225.00 11,02,500.00
26.3 c 3.5 core, 185 sq.mm. Meter 500 972.00 4,86,000.00
26.4 d 3.5 core, 150 sq.mm. Meter 2200 780.00 17,16,000.00
26.5 e 3.5 core, 120 sq.mm. Meter 800 658.00 5,26,400.00
26.6 f 3.5 core, 95 sq.mm. Meter 800 527.00 4,21,600.00
26.7 g 3.5 core, 70 sq.mm. Meter 800 540.00 4,32,000.00
26.8 h 3.5 core, 50 sq.mm. Meter 400 312.00 1,24,800.00
26.9 i 3.5 core, 35 sq.mm. Meter 900 242.00 2,17,800.00
26.10 j 4 core, 25 sq.mm. Meter 900 200.00 1,80,000.00
26.11 k 4 core, 16 sq.mm. Meter 2800 159.00 4,45,200.00
26.12 l 4 core, 10 sq.mm. Meter 2800 140.00 3,92,000.00
26.13 m 4 core, 6 sq.mm. Meter 200 111.00 22,200.00
26.14 n 4 core, 4 sq.mm. Meter 200 88.00 17,600.00
26.15 o 2 core, 10 sq.mm. Meter 3600 155.00 5,58,000.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
26.16 p 2 core, 6 sq.mm. Meter 3200 99.00 3,16,800.00
27.00 NS-27 32 Amp 3 phase, 415 volt, 50 Hz water tight (IP-55) socket outlet with interlocking switch complete Nos 5 5,550.00 27,750.00
with all fixing accessories.
28.00 NS-28 single phase 240 Volt, 50 Hz, water tight (IP-55) socket outlet with interlocking switch
complete with all the fixing accessories as below.
28.1 a 32 Amps Nos 10 5,550.00 55,500.00
28.2 b 20 Amps Nos 10 4,225.00 42,250.00
29.00 NS-29 Movement detectors (Infrared Type) Inbuilt ambient light sensor with adjustable lux level 5 to Nos 150 3,440.00 5,16,000.00
600 lux, adjustable time delay from 1 minute to 15 minute, adjustable detection range 0 to 12
meter. The movement detector shall have lens, 360 deg and coverage area shall not be less than
48 sq. meter if height is 2.7 meter. The contact rating shall be suitable for 2000 watt light load.
30.00 NS-30 Following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable including
termination complete as required in existing cable tray.
30.1 a 1C x 35 sq.mm PVC Insulated cu wire including termination etc. for server earthing. Meter 400 295.00 1,18,000.00
30.2 b 1C x 25 sq.mm PVC Insulated cu wire including termination etc. for server earthing. Meter 350 198.00 69,300.00
30.3 c 1C x 16 sq.mm PVC Insulated cu wire including termination etc. for server earthing. Meter 800 138.00 1,10,400.00
30.4 d 1C x 6 sq.mm PVC Insulated cu wire including termination etc. for UPS DB & HUB Room Rack Meter 150 70.00 10,500.00
earthing.
31.00 NS-31 Earthing Junction Box size - 400mm x 300mm x 80mm made out of 2.0mm CRCA sheet with Set 10 2,748.00 27,480.00
seven tank process & powder coating, earthing link (32mm x 6mm copper strip) front door with
glass as complete as required.
32.00 NS-32 Insulating mat 1000 mm. Wide to withstand 1.1 KV, 2.0 mm thick dielectric strength as per latest IS Meter 150 2,590.00 3,88,500.00
DISTRIBUTION PANEL
33.00 NS-33 MAIN L.T. PANELS
MAIN L.T. PANEL CUM CAPACITOR PANEL-
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
Main LT Panel - The panel will be totally enclosed type with, free standing, floor mounted,
indoor duty, dust & vermin proof, front operated, electrical panel fabricated from 2 mm thick
CRCA Sheet as per specifications & drawing laid in this document and will be complete with the
main and auxiliary bus bars, ammeter, ammeter selector switch, voltmeter, voltmeter selector
switch, indication lamps, CT's, protection MCB, interconnection wiring, earth bus and will be
powder coated finish with 70 micron thickness. All the busbar joint shall be protected by clip
on type sleeve. The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3
phase, 50 Hz, 3 phase 4 wire supply system and having following incomming and outgoing Air
Circuit Breakers, MCCB as per the drawing and specification. Fault level of panel shall be 50 KA.
Each incoming / outgoing breaker shall have microprocessor release with adjustable over
current, short circuit & earth fault protection with instantaneous as mentioned in
specification. The Panel will be made as per detailed specifications & drawings forming part of this
document.
(Each Incomming / Outgoing MCCB shall have microprocessor release and variable current
setting from front, adjustable overcurrent, short circuit & earth fault protection, front
extended lockable handle, pad lockable in off position, shrouding on incomer side,
termination shall be suitable for aluminium bus bars / cables and as per specification.)
INCOMING
2 No. 2500 Amp FP MDO horizontal drawout type Air Circuit Breaker microprocessor
based releases for O/C,S/C & earth fault protection with instantaneous. (For Incommer) (50
KA)
BUSCOUPLER
1 Nos. 2500Amp FP MDO horizontal drawout type Air Circuit Breaker as buscoupler with
interlocking arrangement with incomers. (50 KA)
1 Sets of indicating lamps for ON & OFF of bus coupler.
BUSBARS
3000 Amp TPN busbars of aluminium alloy as per SLD+C322
OUTGOING
EACH OUTGOING FEEDER SHALL HAVE DIGITAL ENERGY METER & ALL THE METER
SHALL HAVE MAXIMUM DEMAND RECORDER FACILITY.
2 Nos. 1000A FP MDO ACB with microprocessor based over current, short circuit, earth fault
protections, ON /OFF /TRIP indication.
2 Nos. 800A FP MDO ACB with microprocessor based over current, short circuit, earth fault
protections, ON /OFF /TRIP indication.
2 Nos. 630 Amp TP MCCB.
9 Nos. 400 Amp TP MCCB.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
8 Nos. 250 Amp TP MCCB.
4 Nos. 160 Amp TP MCCB.
2 Nos. 125 Amp TP MCCB.
5 Nos. 63 Amp TP MCB.
INSTRUMENTS
2 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB
(96mm square) (one for each Incoming Breaker).
2 No. 0 to 2500 Amp digital ammeter (96mm square) with CT's.
2 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker).
2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).
2 Sets trip circuit healthy indicating lamp (one set for each incoming breaker).
2 Sets auto trip indicating lamp (one set for each incoming breaker).
2 Set of CT's one of 800/ 5Amp ratio for APFC relay.
2 Nos. Frequency meter (one for each Incoming Breaker).
2 Nos. master trip relay (one for each Incoming Breaker).
2 Nos. 3 phase, over voltage & under voltage relay.
2 Nos. 3 phase, phase reversal relay with single phasing preventor.
2 Nos. 6 window announciator with hooter, accept & reset push button.
01 Set of Mechanical Interlocking for Incomming & Bus coupler breaker.
300 KVAR CAPACITOR BANK PANEL - 02 SET. (EACH SET SHALL HAVE
FOLLOWING)-
INCOMING
1 Nos. 630 Amp TPN Moulded Case Circuit Breaker. (Already Considered in Main.
L.T. Panel Outgoing)-
1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB
(96mm square).
1 No. 0 to 800 Amp digital ammeter (96mm square) with CT's)
1 Sets of phase indicating lights (RYB) with protection fuses.
1 Sets breaker 'ON' & 'OFF' indicating lamp.
12 Step Automatic Power Factor Correction relay (APFC relay).
BUSBARS
1000 Amp TPN busbars of aluminium alloy as per SLD.
OUTGOING
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
4 Nos. 125 Amp TP MCCB.
5 Nos. 63 Amp TP MCCB.
3 Nos. 32 Amp TP MCCB.
3 Nos. capacitor duty contactor (one for each 50KVAR capacitor unit).
5 Nos. capacitor duty contactor (one for each 25KVAR capacitor unit).
3 Nos. capacitor duty contactor (one for each 10/5KVAR capacitor unit).
3 Nos. 50 KVAR Capacitor Bank.
5 Nos. 25 KVAR Capacitor Bank.
2 Nos. 10 KVAR Capacitor Bank.
1 Nos. 5 KVAR Capacitor Bank.
12 sets of push button stations Red and Green for manual operation of capacitor units with
auto/manual selector switches.
1 No. Indicating lamp for each 50 / 25 / 10 / 5 KVAR capacitor unit to indicate that the
unit is 'ON'.
1 No. Toggle switch for changing automatic to manual operation of capacitor units.
Power factor meter.
Main L.T. Panel Cum Synchronizing Panel Describe as above. Set 1 51,50,000.00 51,50,000.00
34.00 NS-34 DG Synchronizing Cum Changeover Panel (1x500 KVA+1x250 KVA+1X500 KVA+ 2X1600
KVA TRANSFORMER) (2x500+1x250KVA D.G. set shall have
synchronized &Load Management function.)
Main DG Control panel with D.G. Synchronizing controller & Micro PLC, this will be floor mounted,
free standing, compartmentalized, indoor duty, dust proof, vermin proof, front operated, electrical
panel fabricated, painted and manufactured exactly as per specifications laid in this document
and will be complete with the main and auxiliary bus bars, interconnection, earth
terminals, earth bus and will be powdered coated finished. All the busbar joint shall be protected
by clip on type sleeve. The DG control panel shall use all draw out 3 position withdrawn
type breakers suitable for 415 V AC, 3 phase, 50 Hz, 4 wire supply system and will have fault
level of 50 KA or as required as per consultant approval. The panel will be made as
per detailed specifications and drawings forming part of this document. (Under no case
temperature of LT Panel shall be more at any point of the panel, otherwise necessary
exhaust fan shall be have to provided) Bus bar calculations considering temperature
derating, enclosure derating, sleeving derating must be done and submitted for checking.
(The D.G.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
Contractor shall make complete protection curves and discrimination chart for relay settings and
shall adjust all these readings at site. The bus bar size shall not be less than the ampere sizes
mentions after derating. The bidder will show exact calculations & compare the figure of 0.66 and
final calculations will be adopted for more stringent condition. each incommer shall have
surge protection device. Any additional requirement of Micro PLC, hardware, software,
auxiliary relays etc shall be considered in this item to full fill the above function.The PCC
panel will comprise of the following :
Each incoming / outgoing breaker shall have microprocessor release with adjustable over
current, short circuit & earth fault protection with instantaneous as mentioned in
specification. The Panel will be made as per detailed specifications & drawings forming part of
this document. Fault level of panel shall be 50 KA.
All the MCCB up to 250 Amp shall have thermal release with adustable overload, short
circuit & earth fault protection and above shall have microprocessor release with adjustable
overload, short circuit & earthfault protection. The panel shall be manufactured as per BOQ, tech
specification and drawing.
One set of Generator control relay for Each D.G. Set with accessories for AMF, Load
Management, Synchronizing and Interlocking through micro PLC.
1 Nos. 800A feeder incomer and Each incomer breaker feeder shall have following: (For
500 KVA D.G. Set)-
One number incomer 3P 800 amps EDO breaker with 400 Amp TP neutral contactor. Each
breaker shall have microprocessor based releases for O/C,S/C & earth fault protection with
instantaneous.
3 Nos. indicating lamps to show the incoming power along with HRC fuses.
1 No digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector switch.
1 No. Load Manager EM 6400 with RS 485 port
1 no. REF relay
Announciation window to cover LLOP, HWT, OIL Pressure, U/V, O/V, U/F, O/F, O/C, E/F, REF
relay faults shall be provided. 2 nos phase reversal relay shall be provided.
Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other faults.
Initially U/V & U/F will be bye passed till oil pressure is picked up.
Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G. fails to
start.
Generator start /stop facility through push button from panel, necessary cranking relay shall
be provided.
Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter. D.C voltmeter and
ammeter will be analouge type.
Whenever D.G. stop through PB, load shall be disconnected first.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 Nos. 800A feeder incomer and Each incomer breaker feeder shall have following: (For
500 KVA D.G. Set)-
One number incomer 3P 800 amps EDO breaker with 400 Amp TP neutral contactor. Each
breaker shall have microprocessor based releases for O/C,S/C & earth fault protection with
instantaneous.
3 Nos. indicating lamps to show the incoming power along with HRC fuses.
1 No digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector switch.
1 No. Load Manager EM 6400 with RS 485 port
1 no. REF relay
Announciation window to cover LLOP, HWT, OIL Pressure, U/V, O/V, U/F, O/F, O/C, E/F, REF
relay faults shall be provided. 2 nos phase reversal relay shall be provided.
Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other faults.
Initially U/V & U/F will be bye passed till oil pressure is picked up.
Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G. fails to
start.
Generator start /stop facility through push button from panel, necessary cranking relay shall
be provided.
Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter.
D.C voltmeter and ammeter will be analouge type.
Whenever D.G. stop through PB, load shall be disconnected first.
1 Nos. 400A feeder incomer and Each incomer breaker feeder shall have following: (For
250 KVA D.G. Set)-
One number incomer 4P 400 amps moulded case circuit breaker with 400 Amp 4P power
contactor. Each breaker shall have microprocessor based releases for O/C,S/C & earth fault
protection with instantaneous.
3 Nos. indicating lamps to show the incoming power along with HRC fuses.
1 No digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector switch.
1 No. Load Manager EM 6400 with RS 485 port
Announciation window to coverthe common fault.
Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other faults.
Initially U/V & U/F will be bye passed till oil pressure is picked up.
Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G. fails to
start.
Generator start /stop facility through push button from panel, necessary cranking relay shall
be provided.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
Suitable battery charger for 12V 360 AH with d.c voltmeter & d.c ammeter.
D.C voltmeter and ammeter will be analouge type.
Whenever D.G. stop through PB, load shall be disconnected first.
INCOMING FROM MAIN L.T. PANEL-
2 No. 1000 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker
microprocessor based releases for O/C,S/C & earth fault protection with instantaneous.
(For Incommer) (50 KA)
BUSCOUPLER
1 Nos. 1000 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker as
buscoupler with interlocking arrangement with incomers. (50 KA)
1 Nos. 800 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker as
buscoupler with interlocking arrangement with incomers. (50 KA)
2 Sets of indicating lamps for ON & OFF of bus coupler.
BUSBARS
1250 Amp TPN busbars of aluminium alloy as per SLD.
OUTGOING
ALL THE METER SHALL HAVE DUAL SOURCE ELECTRONIC ENERGY
METER WITH MAXIMUM DEMAND RECORDER FACILITY.
01 Nos 630A TP MCCB Moulded Case Circuit Breaker.
04 Nos 400A TP Moulded Case Circuit Breaker.
08 Nos 250A TP Moulded Case Circuit Breaker.
07 Nos 160A TP Moulded Case Circuit Breaker.
03 Nos 125A TP Moulded Case Circuit Breaker.
04 Nos 100A TP Moulded Case Circuit Breaker.
04 Nos 63A TP Moulded Case Circuit Breaker.
INSTRUMENTS
5 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB
(96mm square) (one for each Incoming Breaker).
4 No. 0 to 630/800 Amp digital ammeter (96mm square) with CT's.
2 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker).
2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).
2 Sets trip circuit healthy indicating lamp (one set for each incoming breaker).
2 Sets auto trip indicating lamp (one set for each incoming breaker).
2 Nos. Multifunction Meter (one for each Incoming Breaker).
BATTERY & BATTERY CHARGER
1 No. 24V, 72AH SMF Battery with suitable battery charger for control supply.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
Synchronizing Cum Changeove Panel Described as above. Set 1 37,87,500.00 37,87,500.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
300 Amp TPN aluminium busbar.
OUTGOING
06 No. 100 Amp FP MCCB
01 No of control / power wiring.
Panel described as above Set 2.00 1,32,000.00 2,64,000.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
01 No of control / power wiring.
Panel described as above Set 1 1,74,800.00 1,74,800.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
100 Amp TPN aluminium busbar.
OUTGOING
03 No. 40 Amp TPN Miniature Circuit Breaker
01 No of control / power wiring.
Panel described as above Set 1.00 47,500.00 47,500.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 No of control / power wiring.
Panel described as above Set 2.00 2,79,400.00 5,58,800.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.
1 No. 100 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set of Electronic KWH Meter.
BUS BARS
125 Amp TPN aluminium bus bar.
OUTGOING
03 No. 63 Amp TPN Miniature Circuit Breaker.
02 No. 40 Amp TPN Miniature Circuit Breaker.
1 No of control / power wiring.
Panel described as above Set 6.00 71,500.00 4,29,000.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
BUS BARS
100 Amp TP+2N copper bus bar.
OUTGOING
06 Nos 40 Amp FP Miniature Circuit Breaker.
02 Nos 25 Amp DP Miniature Circuit Breaker.
1 No of control / power wiring.
Panel described as above Set 2.00 76,800.00 1,53,600.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.
1 No.63 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set of Electronic KWH Meter.
BUS BARS
100 Amp TPN aluminium busbar.
OUTGOING
05 No. 40 Amp TPN Miniature Circuit Breaker.
1 No of control / power wiring.
Panel described as above Set 1 1,51,900.00 1,51,900.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
300 Amp TPN aluminium bus bar.
OUTGOING
EACH OUTGOING SHALL HAVE ELECTRONIC KWH METER WITH MAXIMUM DEMAND
RECORDING FACILITY.
2 Nos 125 Amp FP Moulded Case Circuit Breaker
5 Nos 63 Amp TPN MCB
10 Nos 40 Amp TPN MCB
1 No of control / power wiring.
Panel described as above Set 1.00 74,440.00 74,440.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
1 No.800 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set of Electronic KWH Meter
BUS BARS
800 Amp TPN aluminium busbar.
OUTGOING
01 No. 400 Amp FP Moulded Case Circuit Breaker.
04 No. 315 Amp FP Moulded Case Circuit Breaker.
01 No. of control / power wiring.
Panel described as above Set 1.00 6,26,000.00 6,26,000.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
04 No. 250 Amp TP MCCB.
02 No. 125 Amp TP MCCB.
01 No. 63 Amp TP MCCB.
Panel described as above Set 1.00 4,61,000.00 4,61,000.00
40.00 NS-40 Cable Tray Supports System with mounting accessories, necessary bands, couplers,
including bolts & nuts etc. as required on beams or trenches or on wall or columns.
Ladder type cable trays of following sizes:
40.1 a. 600mm wide Mtr. 90 950.00 85,500.00
40.2 b. 450mm wide Mtr. 90 690.00 62,100.00
40.3 c. 300mm wide Mtr. 90 518.00 46,620.00
41.00 NS-41 Telescopic trolley (For Indoor Circuit Breaker Maintance) No 2 47,515.00 95,030.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
items (Rs.) (Rs)
III EXTERNAL ELECTRIFICATION WORKS (SUPPLY)- NS item
42.00 NS-42 Single Core 2.5 sq.mm Copper Conductor PVC insulated wires in the lighting poles form junction
box to lighting fixtures, as required.
a. Red Colour Mtr. 1000 48.00 48,000.00
b. Black Colour Mtr. 1000 48.00 48,000.00
c. Green Colour Mtr. 1000 48.00 48,000.00
45.00 NS-45 Maintenance free earthing System/ Ground Enhancing Material Earthing System using copper Lot 1 21,590.00 21,590.00
bonded earth rods and Ground Enhancement Material, as per scope of work and technical
specifications and as per IEEE 80 (14.5 d) standard, including measurement of soil resistivity
before start of work and earthing system resistance after completion of work.
2.0 NS-2 33KV, SINGLE BREAKER PANEL- (INDOOR TYPE) Set 1.00 21,500.00 21,500.00
33 KV VCB Single Breaker Panel Board as Icomming / Outgoing shall be metal clad floor
mounting complete as per specification and as described.
630 A VCB Breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV rated, totally
enclosed, air insulated metal clad housing, floor mounting, horizontal isolation, vermin
proof, fully interlocked horizontal drawout type having isolation features and control
devices complete with the following.
Manually and motor operated, spring charged (release closing mechanism) trip free type,
triple pole truck mounted draw out, VCB, incorporating mechanical as well as
electrical ON/OFF indication. Spring charge/discharge mechanical indication"OFF"
push buttons for emergency trip (shrouded) test/service position limit switches with 6
NO/6NC breaker auxilliary contacts in service position, 24 Volts DC shunt trip coil and
strip heater to prevent moisture absorption.
INCOMING PANEL - 1 NO. (Incoming Panel shall have following)-
1 No 630 A VCB Breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV rated,
totally enclosed, air insulated metal clad housing, floor mounting, horizontal isolation,
vermin proof, fully interlocked horizontal drawout type having isolation features and control
devices complete with the following:
3 No. Single Phase double core current transformer 120/5-5 Amp epoxy cast resin
insulated class of insulation E.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
Core 1-15VA burden class 1.0 for metering.
Core 2-15VA burden class 5P20 for protection.
P.T's of 33KV/1.732, 110V/1.732, 100VA with suitable rating H.T. & L.T. fuse
conforming to relevant IS Standards and complete as required.
One no. numerical microprocessor based three phase over current (IDMT element) with
earth fault relay with instantaneous elements.
1 No. Anti Pumping device.
1 No. Circuit breaker control switch for electrical (T/N/C).
1 No. limit switch for test & service position .
1 No. Voltmeter (0-36KV) with selector switch. (96mm square).
1 No. Ammeter (0-100Amp) with selector switch. (96mm square).
1 No. electronic type digital energy analyser having 30 days memory and parameters of
KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all
accessories.
1 Set of following indicating lamps.
Red, Yellow & Blue for phase indication.
Amber for Trip indication.
Red `ON' Green `OFF'
Spring charge indication.
Auto trip indication.
1 No. hooter with hooter acceptance and reset push button.
1 No. master trip relay. (Electromechanical Type)
1 No. Over voltage relay. (Static Type)
1 No. Under voltage relay. (Static Type)
12 window announciator for all electrical and transformer fault.
1 No.Trip ckt supervision relay (Electromechanical Type)
1 Set of fuses, ferrules, wiring etc. as required.
1 Set of battery and battery charger suitable for 12 Hour backup for all control
supply.
2 No. control Transformer of 1KVA for giving supply to indication lamps etc having 33
KV/415-230V AC rating epoxy cast resin dry type Transformer. The connection for control
transformer shall be taken from the cable side before the circuit breaker tapping.
Note: All spare contacts of breaker or any other equipment inside the breaker shall
be wired upto the outgoing terminal strip with appropriate ferrules / coding. The
terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
providing minimum size strip suitable for 4/6sqmm.
3.0 NS-3 33 KV HT VCB Three Breaker Panel Board (Indoor Type) (1 Incomming Set 1.00 43,100.00 43,100.00
+ 4 Outgoing)
33 KV Three Breaker Vacuum Circuit Breaker Panel Board as 1 Incomming & 4
Outgoing shall be metal clad floor mounting complete as per specification and as
described.
630 A Vacuum circuit breaker of (350 MVA) 18.4 KA ruputuring capacity at 33 KV
rated, totally enclosed,air insulated metal clad housing, floor mounting, horizontal
isolation, vermin proof, fully interlocked horizontal drawout type having isolation
features and control devices complete with the following.
Manually and motor operated, spring charged (release closing mechanism) trip free
type,triple pole truck mounted draw out, vacuum circuit breaker, incorporating
mechanical as well as electrical ON/OFF indication. Spring charge/discharge
mechanical indication"OFF" push buttons for emergency trip (shrouded) test/service
position limit switches with 6 NO/6 NC breaker auxilliary contacts in service position, 24
Volts DC shunt trip coil and strip heater to prevent moisture absorption.
INCOMING PANEL - 1 NO.
1 No 630 A Vacuum circuit breaker of (350 MVA) 18.4 KA ruputuring capacity at
33 KV rated, totally enclosed,air insulated metal clad housing, floor mounting, horizontal
isolation,vermin proof,fully interlocked horizontal drawout type having isolation features
and control devices complete with the following:
3 No. Single Phase double core current transformer 120/5 Amp epoxy cast insulated class
of insulation E.
Core 1-15VA burden class 1.0 for metering.
Core 2-15VA burden class 5P20 for protection.
P.T's of 33KV/1.732, 110V/1.732, 100VA with suitable rating H.T. & L.T. fuse
conforming to relevant IS Standards and complete as required.
One no. numerical microprocessor based three phase over current (IDMT element) (2
O/C+1E/F) with earth fault relay with instantaneous elements.
1 No. Anti Pumping device.
1 No. Circuit breaker control switch for electrical (T/N/C).
1 No. limit switch for test & service position .
1 No. Voltmeter (0-36KV) with selector switch. (96mm square).
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 No. Ammeter (0-100Amp) with selector switch. (96mm square).
1 No. electronic type digital energy analyser having 30 days memory and parameters of
KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all
accessories.
1 Set of following indicating lamps.
Red, Yellow & Blue for phase indication.
Amber for Trip indication.
Red `ON' Green `OFF'
Spring charge indication.
Auto trip indication.
1 No. hooter with hooter acceptance and reset push button.
1 No. master trip relay. ( Electromechanical Type )
1 No.Trip ckt supervision relay. (Electromechanical Type )
600A color coded heat shrinkable sleeved TP Copper busbar of 350 MVA fault rating.
1 Set of fuses, ferrules, wiring etc. as required.
1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete as required.
2 No. control Transformer of 1KVA for giving supply to indication lamps etc having
33KV/415-230V AC rating epoxy cast resin dry type Transformer. The connection for
control transformer shall be taken from the cable side before the circuit breaker tapping.
Note: All spare contacts of breaker or any other equipment inside the breaker shall
be wired upto the outgoing terminal strip with appropriate ferrules / coding. The
terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to
OUTGOING PANEL - 4 NO. (Each outgoing feeder shall have following)
1 No 630 A Vacuum circuit breaker of (350 MVA) 18.4 KA ruputuring capacity at
33 KV rated, totally enclosed,air insulated metal clad housing, floor mounting, horizontal
isolation,vermin proof,fully interlocked horizontal drawout type having isolation features
and control devices complete with the following:
3 No. Single Phase double core current transformer 60/5 Amp epoxy cast insulated class
of insulation E.
Core 1-15VA burden class 1.0 for metering.
Core 2-15VA burden class 5P20 for protection.
One no. numerical microprocessor based three phase over current (IDMT element) (2
O/C+1E/F) with earth fault relay with instantaneous elements.
1 No. Anti Pumping device.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 No. Circuit breaker control switch for electrical (T/N/C).
1 No. limit switch for test & service position .
1 No. Voltmeter (0-36KV) with selector switch. (96mm square).
1 No. Ammeter (0-50Amp) with selector switch. (96mm square).
1 No. electronic type digital energy analyser having 30 days memory and parameters of
KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all
accessories.
1 Set of following indicating lamps.
Red, Yellow & Blue for phase indication.
Amber for Trip indication.
Red `ON' Green `OFF'
Spring charge indication.
Auto trip indication.
1 No. hooter with hooter acceptance and reset push button.
1 No. master trip relay. ( Electromechanical Type)
1 No.Trip ckt supervision relay (Electromechanical Type)
1 Set of fuses, ferrules, wiring etc. as required.
3 No. VAA33 auxiliary relay for transformer fault, alarm and trip.
12 Annunciator window for all electrical and transformer fault.
Note: All spare contacts of breaker or any other equipment inside the breaker shall
be wired upto the outgoing terminal strip with appropriate ferrules / coding. The
terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to
providing minimum size strip suitable for 4/6sqmm.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
8.2 b Insulation of above pipe with rockwool of min 75mm. thickness min. 144Kg/ m3
density and 26 SWG Aluminium cladding inside & outside DG room complete. Insulation
will be done in such a way that temperature surrounding it shall not exceed 7
deg. beyond ambient. The above specifications shall be based on calculation
subject to minimum ratings given above.
Insulation and cladding for exhaust ducting inside genset room area and outside Sqm 20 432.00 8,640.00
using 75 mm thick rockool of density 144 Kg/ M3 & 24 SWG Aluminium Sheet.
8.3 c MS structure for supporting of DG emission, exhaust piping with RCC foundation and Kg. 1200 8.00 9,600.00
in cable trench for cable support etc. complete in all respect.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
g) Complete with other provision for execution in the confirmation with detailed technical
specifications.
h) Lightning conductor finial made of 25mm dia 300 mm long G.I.tube having single prong.
i) Integral single power tool (electrical) for lowering & raising of high mast with separate
manually operated system.
j) Anchor plate, templates, foundation bolts manufactured from special steel along with
nuts washers etc
k)Design & casting of RCC Foundation
10.4 d Dust vermin and weather proof out door compartmentalized feeder pillar of suitable size Each 7 4,300.00 30,100.00
made of 2.0 mm M.S. sheet complete with the following:-
a) Canopy at top, IP 55
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
b) Hinged door open able on both side with heavy duty locking system.- 02 nos
c) Base frame with detachable cover on all sides made out of 2.0 mm steel sheet.
d) Legs of suitable length make out of 40mm x 40mm x 6mm angle iron including grouting
the legs in 1:2:4 CC (1 Cement 2 coarse sand 4 stone aggregate of 40 mm nominal size).
e) Knock out holes at bottom for cable entry
f) Earthing stud- 02 nos
g) Powder coated of approved shade.
h) 63 amps TPN MCB, 16K breaking capacity- 01 No,
i) 40 Amps TP air brake contactor
j) 24 hour Electronic timer 01 No
k) Heavy duty godown lock- 02 Nos.
l) power tool control with with 02 nos 09 Amps contactors
m) raise/lower push button
n) Termination incoming/outgoing cables with suitable sizes of ferrules & compression
gland
o) O/L and SPP motor protection.
11.0 NS-11 Flange mounted hot dip Galvanized Octangonal Pole of 7 Mtr height made from 3.5 mm Each 60 2,590.00 1,55,400.00
thick HT Steel plate, having top dia-90mm & bottom dia of 155 mm complete with window
with flash cover at a height of 500mm from the base for cable termination block etc and
galvanized base plate of size 220 mm x 220mm x 12 mm thick on existing cement
concrete pedestal as required including supplying and fixing the following in the window
box provided for cable termination as per direction of engineer incharge:-
a) Supplying and fixing 6mm thick laminated mounted sheet inside the window mounted
on and including providing and welding 02 nos G.I. strips 4mm thick of suitable length and
having suitable size tapped holes as reqd.
b) Supplying and fixing 63 Amps terminal block, suitable for 10 sq.mm conductor- 04 nos
& shorting links- 05 nos. on DIN Channel including providing. And fixing DIN Channel of
suitable length- 01 nos on the existing laminated sheet.
c) Supplying and fixing 6 Amps, SPMCB, C characteristics curve- 02 nos, Earth stud 02
nos, welded at suitable height, washers, springs washers & nuts.
d) M - 20 reinforced cement concrete foundation of size 550mm x 550mm wide and 1200
mm deep i/c excavation of earth, providing cutting, bending and placing in position,
reinforcement of cold twisted bars of 12 mm dia- 1200 mm long (approx)- 08 nos and
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
reinforcement ring of cold twisted bar of 8 mm dia-190 spacing centre to centre (approx)-
as required with positioning of foundation bolts as shown in the item given below and
providing 63 mm (O.D.) PVC Pipe of suitable length for cable entry & exit as required.
e) 04 nos, M20X470mm j-type (EN8grade) foundation bolt (total length 600mm) with nuts,
12.0 NS-12 Flange mounted hot dip Galvanized Octangonal Pole of 9 Mtr height made from 4 mm Each 30 2,590.00 77,700.00
thick HT Steel plate, having top dia-90mm & bottom dia of 185 mm complete with window
with flash cover at a height of 500mm from the base for cable termination block etc and
galvanized base plate of size 220 mm x 220mm x 12 mm thick on existing cement
concrete pedestal as required including supplying and fixing the following in the window
box provided for cable termination as per direction of engineer incharge:-
a) Supplying and fixing 6mm thick laminated mounted sheet inside the window mounted
on and including providing and welding 02 nos G.I. strips 4mm thick of suitable length and
having suitable size tapped holes as reqd.
b) Supplying and fixing 63 Amps terminal block, suitable for 10 sq.mm conductor- 04 nos
& shorting links- 05 nos. on DIN Channel including providing. And fixing DIN Channel of
suitable length- 01 nos on the existing laminated sheet.
c) Supplying and fixing 6 Amps, SPMCB, C characteristics curve- 02 nos, Earth stud 02
nos, welded at suitable height, washers, springs washers & nuts.
d) M - 20 reinforced cement concrete foundation of size 550mm x 550mm wide and 1200
mm deep i/c excavation of earth, providing cutting, bending and placing in position,
reinforcement of cold twisted bars of 12 mm dia- 1200 mm long (approx)- 08 nos and
reinforcement ring of cold twisted bar of 8 mm dia-190 spacing centre to centre (approx)-
as required with positioning of foundation bolts as shown in the item given below and
providing 63 mm (O.D.) PVC Pipe of suitable length for cable entry & exit as required.
e) 04 nos, M20X470mm j-type (EN8grade) foundation bolt (total length 600mm) with nuts,
13.0 NS-13 72W LED street light type luminaire housing shall be of corrosion free, pressure die cast Each 65 863.00 56,095.00
aluminium, comprising of polycarbonate cover or better, LED chips, mounted on suitable
designed aluminium heat sink with high thermal conductivity for better heat dissipation,
fitted with integral drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket
lining complying to IP 65/66 class of protection (Type: Philips: BRP410 LED CW 072 MR
FG S1 PSU GR or Bajaj: BRTFG 72W LED or Crompton or Wipro: LR02-781-XXX-57-XX
or Surya: SLE UL 72W IP66 LXN) connections as required as per technical specification.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
14.0 NS-14 90W LED street light type luminaire housing shall be of corrosion free, pressure die cast Each 30 863.00 25,890.00
aluminium, comprising of polycarbonate cover or better, LED chips, mounted on suitable
designed aluminium heat sink with high thermal conductivity for better heat dissipation,
fitted with integral drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket
lining complying to IP 65/66 class of protection (Type: Bajaj:BRTFG 90W LED or
Wipro:LR02-102-XXX-57-XX or Surya: SLE UL 90W IP66 LXN or Goldwyn: XS 04 19
Jupiter) connections as required as per technical specification.
15.0 NS-15 Decorative lighting pole 4000 mm height, 4X 100W LED flood light type luminaire Each 1 6,900.00 6,900.00
housing shall be of corrosion free, pressure die cast aluminium, comprising of toughened
clear front glass, LED chips, mounted on suitable designed aluminium heat sink with high
thermal conductivity for better heat dissipation, fitted with integral drivers, stainless steel
toggle clips & neoprene/ synthetic rubber gasket lining complying to IP 65 class of
protection.(Type: Philips:-BVP410 LED 107CW HE NB FG S3 XT or Bajaj: BARFEG
100W LED or Crompton LSFO-72-CDL or Wipro LR18-971-XXX-57-XX or Surya SLE FL
100W IP65 LUMOS). connections as required as per site conditions.
16.0 NS-16 Solar street light system shall be SPV module, based White Light Emitting Diode (W- Set 25 2,590.00 64,750.00
LED) (20W) including all fittings and fixtures, battery and mounted on a pole of suitable
height (minimum 4.0 mt), charger controller, protection, including foundation, earthing with
5 years comprehensive warranty with complete as required. The broad details as specify :
PV Module - 75 Wp, module efficiency should not be less than 13.5 % with IEC 61215
certified, Battery - Lead acid Tubular Flooded / VRLA , 12V- 75 AH @ C/10, Duty Cycle -
Dusk to dawn. The details shall be as per specification as specified.
17.0 NS-17 3.0Mtr, 65mm dia GI pole with finished powder coated, base plate 300 x 300 x 3mm GI No. 50 2,590.00 1,29,500.00
reducer & nipple for mounting the fitting, 4 nos. foundation bolts. It consists of junction box
shall be inside the pole with suitable MCB control & loop-in loop-out arrangement (Make :
BIS Approved make) complete as required as per technical specification.
18.0 NS-18 30/40W LED Post Top Lantern type luminaire housing shall be of corrosion free, cast No. 50 863.00 43,150.00
aluminium spigot, comprising of acrylic diffuser, LED chips, mounted on suitable designed
aluminium heat sink with high thermal conductivity for better heat dissipation, fitted with
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
integral drivers, stainless steel toggle clips & neoprene/ synthetic rubber gasket lining
complying to IP 65 class of protection (Type: Philips or Bajaj: BGCL 40W LED or
Crompton: LPTO-40/CDL or Wipro or Surya: SLE PT 30W-GMP) connections as required
as per technical specification.
19.0 NS-19 30/40W LED Gate light fixture with necessary driver, lamp, connections, wiring & etc. No. 10 863.00 8,630.00
complying to IP 65 class of protection complete as required. (Philips or Bajaj:-BGCS 40W
LED or Crompton or Wipro: or Surya: SLE PT 30W-ETP)
20.0 NS-20 9W LED spike light fixture with necessary driver, lamp, connections, mounting No. 30 863.00 25,890.00
arrangement-spike, wiring & etc. complying to IP 65 class of protection complete as
required. (Philips:-BGP311 3xLED- HP/WW 220-240V 12 1N or Bajaj:-BGSBL 9W LED
WW or Crompton: or Wipro:LF05-600-055-27-XX or Surya: SLE SPLR 9W)
21.0 NS-21 9-10W LED Bollard light fixture with necessary driver lamp, connections, wiring & etc. No. 70 863.00 60,410.00
complying to IP 65 class of protection complete as required. (Philips:BCP150
LED150/WW PSU 220-240V 7043 or Bajaj:BGBOL 605 9W LED or Crompton or Wipro:
CRLA11008HP57-08 or Surya: SLE BL 10W-550)
22.0 NS-22 3/4W LED Step light fixture with necessary driver, lamp, connections, mounting No. 50 431.00 21,550.00
arrangement - wiring & etc. complying to IP 65 class of protection, complete as required.
(Philips:- BWG150 LED50/WW PSU 220-240V IP67 7043 or Bajaj: BLSGV 4W or
Crompton: or Wipro:-LT54-002-XXX-WW-XX or Surya: SLE STL 3W)
23.0 NS-23 IP 68 ,18-20W LED underwater luminaire for swimming pool/splash pool, suitable for use No. 10 1,295.00 12,950.00
with AC 12V with provision of loop in & loop out , complete as required including driver,
230/12V AC transformer,Junction box,etc including connections as required.
24.0 NS-24 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required Meter 600 43.00 25,800.00
26.0 NS-26 1.1KV grade multicore aluminium conductor XLPE insulated and PVC sheathed
armoured cable conforming to relevant IS. (Cable shall be purchased only after
approval of cable schedule by architect / consultant) of following sizes.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
26.1 a 4 core, 6 sq.mm. Meter 200 21.00 4,200.00
26.2 b 4 core, 4 sq.mm. Meter 200 21.00 4,200.00
26.3 c 2 core, 10 sq.mm. Meter 2000 13.00 26,000.00
26.4 d 2 core, 6 sq.mm. Meter 3000 13.00 39,000.00
27.00 NS-27 32 Amp 3 phase, 415 volt, 50 Hz water tight (IP-55) socket outlet with interlocking switch Nos 5 863.00 4,315.00
complete with all fixing accessories.
28.00 NS-28 single phase 240 Volt, 50 Hz, water tight (IP-55) socket outlet with interlocking
switch complete with all the fixing accessories as below.
28.1 a 32 Amps Nos 10 863.00 8,630.00
28.2 b 20 Amps Nos 10 863.00 8,630.00
29.00 NS-29 Movement detectors (Infrared Type) Inbuilt ambient light sensor with adjustable lux Nos 350 863.00 3,02,050.00
level 5 to 600 lux, adjustable time delay from 1 minute to 15 minute, adjustable detection
range 0 to 12 meter. The movement detector shall have lens, 360 deg and coverage area
shall not be less than 48 sq. meter if height is 2.7 meter. The contact rating shall be
suitable for 2000 watt light load.
30.00 NS-30 Following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable
including termination complete as required in existing cable tray.
30.1 a 1C x 35 sq.mm PVC Insulated cu wire including termination etc. for server earthing. Meter 400 21.00 8,400.00
30.2 b 1C x 25 sq.mm PVC Insulated cu wire including termination etc. for server earthing. Meter 350 21.00 7,350.00
30.3 c 1C x 16 sq.mm PVC Insulated cu wire including termination etc. for server earthing. Meter 800 21.00 16,800.00
30.4 d 1C x 6 sq.mm PVC Insulated cu wire including termination etc. for UPS DB & HUB Room Meter 150 13.00 1,950.00
Rack earthing.
31.00 NS-31 Earthing Junction Box size - 400mm x 300mm x 80mm made out of 2.0mm CRCA sheet Set 10 863.00 8,630.00
with seven tank process & powder coating, earthing link (32mm x 6mm copper strip) front
door with glass as complete as required.
32.00 NS-32 Insulating mat 1000 mm. Wide to withstand 1.1 KV, 2.0 mm thick dielectric strength as per Meter 150 172.00 25,800.00
latest IS
DISTRIBUTION PANEL
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
33.00 NS-33 MAIN L.T. PANELS
MAIN L.T. PANEL CUM CAPACITOR PANEL-
Main LT Panel - The panel will be totally enclosed type with, free standing, floor
mounted, indoor duty, dust & vermin proof, front operated, electrical panel fabricated
from 2 mm thick CRCA Sheet as per specifications & drawing laid in this document and
will be complete with the main and auxiliary bus bars, ammeter, ammeter selector
switch, voltmeter, voltmeter selector switch, indication lamps, CT's, protection MCB,
interconnection wiring, earth bus and will be powder coated finish with 70 micron
thickness. All the busbar joint shall be protected by clip on type sleeve. The Main LT
Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase
4 wire supply system and having following incomming and outgoing Air Circuit Breakers,
MCCB as per the drawing and specification. Fault level of panel shall be 50 KA.
Each incoming / outgoing breaker shall have microprocessor release with adjustable
over current, short circuit & earth fault protection with instantaneous as
mentioned in specification. The Panel will be made as per detailed specifications &
drawings forming part of this document.
(Each Incomming / Outgoing MCCB shall have microprocessor release and variable
current setting from front, adjustable overcurrent, short circuit & earth fault
protection, front extended lockable handle, pad lockable in off position, shrouding on
incomer side, termination shall be suitable for aluminium bus bars / cables and as per
specification.)
INCOMING
2 No. 2500 Amp FP MDO horizontal drawout type Air Circuit Breaker
microprocessor based releases for O/C,S/C & earth fault protection with
instantaneous. (For Incommer) (50 KA)
BUSCOUPLER
1 Nos. 2500Amp FP MDO horizontal drawout type Air Circuit Breaker as buscoupler with
interlocking arrangement with incomers. (50 KA)
1 Sets of indicating lamps for ON & OFF of bus coupler.
BUSBARS
3000 Amp TPN busbars of aluminium alloy as per SLD+C322
OUTGOING
EACH OUTGOING FEEDER SHALL HAVE DIGITAL ENERGY METER & ALL THE
METER SHALL HAVE MAXIMUM DEMAND RECORDER FACILITY.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
2 Nos. 1000A FP MDO ACB with microprocessor based over current, short circuit, earth
fault protections, ON /OFF /TRIP indication.
2 Nos. 800A FP MDO ACB with microprocessor based over current, short circuit, earth
fault protections, ON /OFF /TRIP indication.
2 Nos. 630 Amp TP MCCB.
9 Nos. 400 Amp TP MCCB.
8 Nos. 250 Amp TP MCCB.
4 Nos. 160 Amp TP MCCB.
2 Nos. 125 Amp TP MCCB.
5 Nos. 63 Amp TP MCB.
INSTRUMENTS
2 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective
SP MCB (96mm square) (one for each Incoming Breaker).
2 No. 0 to 2500 Amp digital ammeter (96mm square) with CT's.
2 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming
breaker).
2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker) .
2 Sets trip circuit healthy indicating lamp (one set for each incoming breaker) .
2 Sets auto trip indicating lamp (one set for each incoming breaker) .
2 Set of CT's one of 800/ 5Amp ratio for APFC relay.
2 Nos. Frequency meter (one for each Incoming Breaker).
2 Nos. master trip relay (one for each Incoming Breaker) .
2 Nos. 3 phase, over voltage & under voltage relay.
2 Nos. 3 phase, phase reversal relay with single phasing preventor.
2 Nos. 6 window announciator with hooter, accept & reset push button.
01 Set of Mechanical Interlocking for Incomming & Bus coupler breaker.
300 KVAR CAPACITOR BANK PANEL - 02 SET. (EACH SET SHALL HAVE
FOLLOWING)-
INCOMING
1 Nos. 630 Amp TPN Moulded Case Circuit Breaker. (Already Considered in
Main. L.T. Panel Outgoing)-
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective
SP MCB (96mm square).
1 No. 0 to 800 Amp digital ammeter (96mm square) with CT's)
1 Sets of phase indicating lights (RYB) with protection fuses.
1 Sets breaker 'ON' & 'OFF' indicating lamp.
12 Step Automatic Power Factor Correction relay (APFC relay).
BUSBARS
1000 Amp TPN busbars of aluminium alloy as per SLD.
OUTGOING
4 Nos. 125 Amp TP MCCB.
5 Nos. 63 Amp TP MCCB.
3 Nos. 32 Amp TP MCCB.
3 Nos. capacitor duty contactor (one for each 50KVAR capacitor unit).
5 Nos. capacitor duty contactor (one for each 25KVAR capacitor unit).
3 Nos. capacitor duty contactor (one for each 10/5KVAR capacitor unit).
3 Nos. 50 KVAR Capacitor Bank.
5 Nos. 25 KVAR Capacitor Bank.
2 Nos. 10 KVAR Capacitor Bank.
1 Nos. 5 KVAR Capacitor Bank.
12 sets of push button stations Red and Green for manual operation of capacitor
units with auto/manual selector switches.
1 No. Indicating lamp for each 50 / 25 / 10 / 5 KVAR capacitor unit to indicate
that the unit is 'ON'.
1 No. Toggle switch for changing automatic to manual operation of capacitor units.
34.00 NS-34 DG Synchronizing Cum Changeover Panel (1x500 KVA+1x250 KVA+1X500 KVA+
2X1600 KVA TRANSFORMER) (2x500+1x250KVA D.G. set shall have
synchronized &Load Management function.)
Main DG Control panel with D.G. Synchronizing controller & Micro PLC, this will be floor
mounted, free standing, compartmentalized, indoor duty, dust proof, vermin proof, front
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
operated, electrical panel fabricated, painted and manufactured exactly as per
specifications laid in this document and will be complete with the main and
auxiliary bus bars, interconnection, earth terminals, earth bus and will be powdered
coated finished. All the busbar joint shall be protected by clip on type sleeve. The DG
control panel shall use all draw out 3 position withdrawn type breakers suitable for
415 V AC, 3 phase, 50 Hz, 4 wire supply system and will have fault level of 50 KA or as
required as per consultant approval. The panel will be made as per detailed
specifications and drawings forming part of this document. (Under no case
temperature of LT Panel shall be more at any point of the panel, otherwise
necessary exhaust fan shall be have to provided) Bus bar calculations considering
temperature derating, enclosure derating, sleeving derating must be done and
submitted for checking.
Contractor shall make complete protection curves and discrimination chart for relay
settings and shall adjust all these readings at site. The bus bar size shall not be less
than the ampere sizes mentions after derating. The bidder will show exact calculations &
compare the figure of 0.66 and final calculations will be adopted for more stringent
condition. each incommer shall have surge protection device. Any additional
requirement of Micro PLC, hardware, software, auxiliary relays etc shall be
considered in this item to full fill the above function.The PCC panel will comprise
of the following :
Each incoming / outgoing breaker shall have microprocessor release with adjustable
over current, short circuit & earth fault protection with instantaneous as
mentioned in specification. The Panel will be made as per detailed specifications &
drawings forming part of this document. Fault level of panel shall be 50 KA.
All the MCCB up to 250 Amp shall have thermal release with adustable overload,
short circuit & earth fault protection and above shall have microprocessor release
with adjustable overload, short circuit & earthfault protection. The panel shall be
manufactured as per BOQ, tech specification and drawing.
One set of Generator control relay for Each D.G. Set with accessories for AMF, Load
Management, Synchronizing and Interlocking through micro PLC.
1 Nos. 800A feeder incomer and Each incomer breaker feeder shall have
following: (For 500 KVA D.G. Set)-
One number incomer 3P 800 amps EDO breaker with 400 Amp TP neutral contactor.
Each breaker shall have microprocessor based releases for O/C,S/C & earth fault
protection with instantaneous.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
3 Nos. indicating lamps to show the incoming power along with HRC fuses.
1 No digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector
switch.
1 No. Load Manager EM 6400 with RS 485 port
1 no. REF relay
Announciation window to cover LLOP, HWT, OIL Pressure, U/V, O/V, U/F, O/F, O/C,
E/F, REF relay faults shall be provided. 2 nos phase reversal relay shall be
provided.
Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other
faults.
Initially U/V & U/F will be bye passed till oil pressure is picked up.
Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G.
fails to start.
Generator start /stop facility through push button from panel, necessary cranking
relay shall be provided.
Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter.
D.C voltmeter and ammeter will be analouge type.
Whenever D.G. stop through PB, load shall be disconnected first.
1 Nos. 800A feeder incomer and Each incomer breaker feeder shall have
following: (For 500 KVA D.G. Set)-
One number incomer 3P 800 amps EDO breaker with 400 Amp TP neutral contactor.
Each breaker shall have microprocessor based releases for O/C,S/C & earth fault
protection with instantaneous.
3 Nos. indicating lamps to show the incoming power along with HRC fuses.
1 No digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector
switch.
1 No. Load Manager EM 6400 with RS 485 port
1 no. REF relay
Announciation window to cover LLOP, HWT, OIL Pressure, U/V, O/V, U/F, O/F, O/C,
E/F, REF relay faults shall be provided. 2 nos phase reversal relay shall be
provided.
Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other
faults.
Initially U/V & U/F will be bye passed till oil pressure is picked up.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G.
fails to start.
Generator start /stop facility through push button from panel, necessary cranking
relay shall be provided.
Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter.
D.C voltmeter and ammeter will be analouge type.
Whenever D.G. stop through PB, load shall be disconnected first.
1 Nos. 400A feeder incomer and Each incomer breaker feeder shall have
following: (For 250 KVA D.G. Set)-
One number incomer 4P 400 amps moulded case circuit breaker with 400 Amp 4P power
contactor. Each breaker shall have microprocessor based releases for O/C,S/C & earth
fault protection with instantaneous.
3 Nos. indicating lamps to show the incoming power along with HRC fuses.
1 No digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector
switch.
1 No. Load Manager EM 6400 with RS 485 port
Announciation window to coverthe common fault.
Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other
faults.
Initially U/V & U/F will be bye passed till oil pressure is picked up.
Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G.
fails to start.
Generator start /stop facility through push button from panel, necessary cranking
relay shall be provided.
Suitable battery charger for 12V 360 AH with d.c voltmeter & d.c ammeter.
D.C voltmeter and ammeter will be analouge type.
Whenever D.G. stop through PB, load shall be disconnected first.
INCOMING FROM MAIN L.T. PANEL-
2 No. 1000 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker
microprocessor based releases for O/C,S/C & earth fault protection with
instantaneous. (For Incommer) (50 KA)
BUSCOUPLER
1 Nos. 1000 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker as
buscoupler with interlocking arrangement with incomers. (50 KA)
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 Nos. 800 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker as
buscoupler with interlocking arrangement with incomers. (50 KA)
2 Sets of indicating lamps for ON & OFF of bus coupler.
BUSBARS
1250 Amp TPN busbars of aluminium alloy as per SLD.
OUTGOING
ALL THE METER SHALL HAVE DUAL SOURCE ELECTRONIC ENERGY
METER WITH MAXIMUM DEMAND RECORDER FACILITY.
01 Nos 630A TP MCCB Moulded Case Circuit Breaker.
04 Nos 400A TP Moulded Case Circuit Breaker.
08 Nos 250A TP Moulded Case Circuit Breaker.
07 Nos 160A TP Moulded Case Circuit Breaker.
03 Nos 125A TP Moulded Case Circuit Breaker.
04 Nos 100A TP Moulded Case Circuit Breaker.
04 Nos 63A TP Moulded Case Circuit Breaker.
INSTRUMENTS
5 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective
SP MCB (96mm square) (one for each Incoming Breaker).
4 No. 0 to 630/800 Amp digital ammeter (96mm square) with CT's.
2 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming
breaker).
2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker) .
2 Sets trip circuit healthy indicating lamp (one set for each incoming breaker) .
2 Sets auto trip indicating lamp (one set for each incoming breaker) .
2 Nos. Multifunction Meter (one for each Incoming Breaker) .
BATTERY & BATTERY CHARGER
1 No. 24V, 72AH SMF Battery with suitable battery charger for control supply.
Synchronizing Cum Changeove Panel Described as above. Set 1 1,29,000.00 1,29,000.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
CT's, internal wiring with suitable size wires / cable, interconnection, painting
complete as per specification & drawing. All the incomming and outgoing MCCB
shall have 50KA / 35 KA Ics. All the MCCB up to 250 Amp shall have thermal release with
adustable overload and short circuit protection and above shall have microprocessor
release with adjustable overload, short circuit & earthfault protection.
35.1 a ELECTRICAL PANEL (BOYS HOSTEL & GIRLS HOSTEL) (Normal-Raw power)
INCOMING
1 Nos 400 Amp FP Moulded Case Circuit Breaker
1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.
1 No.400 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set of Electronic KWH Meter
BUS BARS
500 Amp TPN aluminium busbar.
OUTGOING
03 No. 160 Amp FP Moulded Case Circuit Breaker.
03 No. 125 Amp FP Moulded Case Circuit Breaker.
01 No. of control / power wiring.
Panel described as above Set 2.00 14,685.00 29,370.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
Panel described as above Set 2.00 6,900.00 13,800.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 Set of Electronic KWH Meter.
BUS BARS
100 Amp TPN aluminium busbar.
OUTGOING
03 No. 40 Amp TPN Miniature Circuit Breaker
01 No of control / power wiring.
Panel described as above Set 1.00 4,320.00 4,320.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
EACH OUTGOING SHALL HAVE ELECTRONIC KWH METER WITH MAXIMUM
DEMAND RECORDING FACILITY.
1 Nos 125 Amp FP Moulded Case Circuit Breaker
05 Nos 100 Amp FP Moulded Case Circuit Breaker
1 No of control / power wiring.
Panel described as above Set 2.00 8,600.00 17,200.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 No of control / power wiring.
Panel described as above Set 2.00 2,160.00 4,320.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
35.16 p UPS PANEL-1 (ACADEMIC BLOCK)
INCOMING
1 Nos 63 Amp FP MCB
1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.
1 No. 63 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set of Electronic KWH Meter.
BUS BARS
100 Amp TP+2N copper bus bar.
OUTGOING
06 Nos 40 Amp FP Miniature Circuit Breaker.
02 Nos 25 Amp DP Miniature Circuit Breaker.
1 No of control / power wiring.
Panel described as above Set 2.00 4,300.00 8,600.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 No. 63 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set of Electronic KWH Meter.
BUS BARS
100 Amp TPN aluminium bus bar.
OUTGOING
03 Nos 40 Amp TPN Miniature Circuit Breaker.
1 No of control / power wiring.
Panel described as above Set 1 4,300.00 4,300.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
BUS BARS
300 Amp TPN aluminium bus bar.
OUTGOING
03 Nos 63 Amp TPN Miniature Circuit Breaker.
12 Nos 63 Amp TPN Miniature Circuit Breaker with Electronic Energy Meter.
2 Nos 63 Amp TPN Miniature Circuit Breaker
1 No of control / power wiring.
Panel described as above Set 1 8,600.00 8,600.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
OUTGOING
04 No. 100 Amp TPN MCB.
02 No. 40 Amp DP MCB.
1 No of control / power wiring.
Panel described as above Set 2.00 8,600.00 17,200.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
36.2 b 40 Amp FP Set 9.00 1,727.00 15,543.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set 24 Hrs TSQ Timer
1 Set 100 Amp, 4P Contactor & A/M switch and Push Button.
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
BUS BARS
100 Amp TPN aluminium busbar.
OUTGOING
09 No. 25 Amp DP MCB.
03 No. 63 Amp TPN MCB.
Panel described as above Set 2.00 12,900.00 25,800.00
40.00 NS-40 Cable Tray Supports System with mounting accessories, necessary bands,
couplers, including bolts & nuts etc. as required on beams or trenches or on wall or
columns.
Ladder type cable trays of following sizes:
40.1 a. 600mm wide Mtr. 90.00 172.00 15,480.00
40.2 b. 450mm wide Mtr. 90.00 172.00 15,480.00
40.3 c. 300mm wide Mtr. 90.00 172.00 15,480.00
41.00 NS-41 Telescopic trolley (For Indoor Circuit Breaker Maintance) No 2.00 864.00 1,728.00
42.00 NS-42 Single Core 2.5 sq.mm Copper Conductor PVC insulated wires in the lighting poles form
junction box to lighting fixtures, as required.
a. Red Colour Mtr. 900.00 13.00 11,700.00
b. Black Colour Mtr. 900.00 13.00 11,700.00
c. Green Colour Mtr. 900.00 13.00 11,700.00
S.No. Non- Description of Item Unit Qty. Unit Rate Total Amount
DSR (Rs.) (Rs)
items
III EXTERNAL ELECTRIFICATION WORKS (Erection)- NSR ITEM
45.00 NS-45 Maintenance free earthing System/ Ground Enhancing Material Earthing System using Lot 1.00 4,300.00 4,300.00
copper bonded earth rods and Ground Enhancement Material, as per scope of work and
technical specifications and as per IEEE 80 (14.5 d) standard, including measurement of
soil resistivity before start of work and earthing system resistance after completion of
work.
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
POINT WIRING
1.0 1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5
sq.mm FRLS PVC insulated copper conductor single core cable in surface /
recessed steel conduit conduit, with modular switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated
copper conductor single core cable etc as required.
a 1.3.3 Group C Point 2500 1,037.00 25,92,500.00
2.0 1.4 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated Point 40 1,094.00 43,760.00
copper conductor single core cable in surface / recessed steel conduit, 2 way
modular switch, modular plate, suitable GI box and earthing the point with 1.5
sq.mm. FRLS PVC insulated copper conductor single core cable etc as
required.
3.0 1.5 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper Meter 35000 239.00 83,65,000.00
conductor single core cable in surface/ recessed steel conduit alongwith 1 No
4 sq. mm FRLS PVC insulated copper conductor single core cable for loop
earthing as required.
4.0 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following
sizes of FRLS PVC insulated copper conductor, single core cable in
surface/ recessed steel... conduit as required.
CIRCUIT / SUBMAIN WIRING
a 1.7.2 2x2.5 sq mm + 1x2.5 sq mm earth wire Meter 20000 206.00 41,20,000.00
b 1.7.4 2x6 sq mm + 1x6 sq mm earth wire. Meter 4000 324.00 12,96,000.00
c 1.7.5 4x2.5 sq mm + 2x2.5 sq mm earth wire. Meter 1000 392.00 3,92,000.00
d 1.7.8 4x4 sq mm + 2x4 sq mm earth wire. Meter 500 374.00 1,87,000.00
e 1.7.9 4x6 sq mm + 2x6 sq mm earth wire. Meter 4000 518.00 20,72,000.00
f 1.7.10 4x10 sq mm + 2x6 sq mm earth wire. Meter 4000 653.00 26,12,000.00
g 1.7.11 4x16 sq mm + 2x6 sq mm earth wire. Meter 3000 930.00 27,90,000.00
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
6.0 1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated Point 400 809.00 3,23,600.00
copper conductor single core cable in surface / recessed medium class
PVC conduit, 2 way modular switch, modular plate, suitable GI box and
earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor
single core cable etc as required.
7.0 1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper Meter 60000 168.00 100,80,000.00
conductor single core cable in surface/ recessed medium class PVC
conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor
single core cable for loop earthing as required.
8.0 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following -
sizes of FRLS PVC insulated copper conductor, single core cable in
surface/ recessed medium class PVC conduit as required.
CIRCUIT / SUBMAIN WIRING -
a 1.14.1 2x1.5 sq mm + 1x1.5 sq mm earth wire Meter 5000 112.00 5,60,000.00
b 1.14.2 2x2.5 sq mm + 1x2.5 sq mm earth wire Meter 20000 137.00 27,40,000.00
c 1.14.3 2x6 sq mm + 1x6 sq mm earth wire. Meter 2000 168.00 3,36,000.00
d 1.14.5 2x10 sq mm + 1x6 sq mm earth wire. Meter 3000 299.00 8,97,000.00
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
9.0 1.17 Wiring with the following sizes of FRLS insulated copper conductor single core -
cables in existing surface/recessed M.S. conduit etc. as complete as required
(includiing conuits for Fire Detection & PA system cabling)
a 1.17.2 2 x 1.5 sq.mm Meter 20000 37.00 7,40,000.00
b 1.17.12 3 x 2.5 sq.mm Meter 1000 75.00 75,000.00
c 1.17.21 3 x 4.0 sq.mm Meter 1000 111.00 1,11,000.00
10.0 1.18 Supplying and drawing following pair 0.5 sq mm FRLS PVC insulated
annealed copper conductor, unarmored telephone cable in the existing
surface/ recessed steel/ PVC conduit as required.
a 1.18.2 2 Pair Metre 8000 19.00 1,52,000.00
11.0 1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper Meter 3000 29.00 87,000.00
conductor PE insulated, shielded with fine tinned copper braid and
protected with PVC sheath in the existing surface/ recessed steel/ PVC
conduit as required.
12.0 1.20 Supplying and fixing of following sizes of STEEL conduit alonwith the -
accessories in surface/recess including painting in case of surface conduit, or
cutting the wall and making good the same in case of recessed conduit as
required. (Conuits for structural cabling & CCTV cabling)
a 1.20.1 20 mm dia Meter 8000 126.00 10,08,000.00
b 1.20.2 25 mm dia Meter 10000 147.00 14,70,000.00
c 1.20.3 32 mm dia Meter 8000 198.00 15,84,000.00
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
14.0 1.22 Supplying and fixing metal box of following sizes (nominal size) on surface or
in recess with suitable size of phenolic laminated sheet cover in front including
painting etc as required.
a 1.22.4 150 mm X 150 mm X 60 mm deep Each 200 168.00 33,600.00
b 1.22.7 200 mm X 150 mm X 60 mm deep Each 200 194.00 38,800.00
15.0 1.24 Supplying and fixing following modular switch/ socket on the existing
modular plate & switch box including connections but excluding modular
plate etc. as required.
a 1.24.1 5/6 amps switch Each 4000 84.00 3,36,000.00
b 1.24.3 15/16 amp switch Each 2000 114.00 2,28,000.00
c 1.24.4 3 pin 5/6 amp socket outlet Each 4000 81.00 3,24,000.00
d 1.24.5 6 pin 15/16 amp socket outlet Each 2000 153.00 3,06,000.00
e 1.24.6 Telephone Socket Outlet Each 400 96.00 38,400.00
f 1.24.7 TV anteena Socket Outlet Each 150 97.00 14,550.00
-
16.0 1.25 Supplying and fixing two module stepped type electronic fan regulator on the Each 1800 288.00 5,18,400.00
existing modular plate switch box including connections but excluding modular
plate etc. as required.
-
17.0 1.26 Supplying and fixing modular blanking plate on the existing modular plate & Each 500 24.00 12,000.00
switch box excluding modular plate as required.
-
18.0 1.27 Supplying and fixing following size/ modules, GI box alongwith modular -
base & cover plate for modular switches in recess etc as required.
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
-
25.0 1.50 Installation of exhaust fan in the existing opening, including making good the -
damage, connection, testing, commissioning etc. as required.
a 1.50.1 Upto 450 mm sweep Each 400 224.00 89,600.00
-
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
S.No. DSR 2016 Description of Item Unit Qty. Rate (Rs) Amount (Rs)
b) Indoor Unit
i NSR VRF CASSETTE : 3.18 Tons 6.00 Nos. 56,260.00 3,37,560.00
ii NSR VRF CASSETTE : 2.55 Tons 4.00 Nos. 53,095.00 2,12,380.00
iii NSR VRF CASSETTE : 2.02 Tons 1.00 Nos. 51,075.00 51,075.00
iv NSR VRF CASSETTE : 1.59 Tons 2.00 Nos. 49,065.00 98,130.00
v NSR VRF CASSETTE : 1.025 Tons 7.00 Nos. 47,395.00 3,31,765.00
vi NSR MID STATIC DUCTED : 4.55 TR 16.00 Nos. 1,18,710.00 18,99,360.00
vii NSR High STATIC DUCTED : 7.96 TR 3.00 Nos. 1,50,725.00 4,52,175.00
d) Indoor Unit
i NSR VRF CASSETTE : 2.55 Tons 3.00 Nos. 53,095.00 1,59,285.00
ii NSR VRF CASSETTE : 2.02 Tons 5.00 Nos. 51,075.00 2,55,375.00
iii NSR VRF CASSETTE : 1.59 Tons 5.00 Nos. 49,065.00 2,45,325.00
iv NSR VRF CASSETTE : 1.025 Tons 9.00 Nos. 47,395.00 4,26,555.00
v NSR MID STATIC DUCTED : 4.55 TR 15.00 Nos. 1,18,710.00 17,80,650.00
f) Indoor Unit
i NSR VRF CASSETTE : 3.18 Tons 30.00 Nos. 56,260.00 16,87,800.00
ii NSR VRF CASSETTE : 2.55 Tons 6.00 Nos. 53,095.00 3,18,570.00
iii NSR VRF CASSETTE : 2.02 Tons 2.00 Nos. 51,075.00 1,02,150.00
iv NSR VRF CASSETTE : 1.025 Tons 22.00 Nos. 47,395.00 10,42,690.00
h) Indoor Unit
i NSR VRF CASSETTE : 3.18 Tons 24.00 Nos. 56,260.00 13,50,240.00
ii NSR VRF CASSETTE : 2.55 Tons 6.00 Nos. 53,095.00 3,18,570.00
iii NSR VRF CASSETTE : 2.02 Tons 2.00 Nos. 51,075.00 1,02,150.00
iv NSR VRF CASSETTE : 1.025 Tons 22.00 Nos. 47,395.00 10,42,690.00
i) NSR Imported fittings Y-joints and headers etc. 187.00 Nos. 5,380.00 10,06,060.00
j) NSR Main centrallised controller suitable for indoor units. (one for A1 & one for A2). 4.00 Nos. 1,04,540.00 4,18,160.00
"SUB-TOTAL-SH-I" 301,00,853.00
2 Refrigerant Piping
Providing, fixing, testing and commissioning of Interconnecting refrigerant pipe
work with (19 mm / 13 mm thick)tubular nitrile rrubber insulation between each
set of indoor & outdoor units as per specifications, all piping inside the room
shall be properly supported with G.I hanger as per specification and
drawings.The Exposed pipe shall be covered with U.V barrier coating with the
use of 5 mil glass cloth .Exterior pipe shall be layed on cable tray of 16 S.W.G
and shall be further covered with similar run of cable tray duly covered with G.I
Sheet of 18 S.W.G for mechanical protection.
2.1 NSR 41.3 mm O.D.(insulation : 19 mm) 350.00 Rm 2,066.00 7,23,100.00
2.2 NSR 34.9 mm O.D.(insulation : 19 mm) 250.00 Rm 1,876.00 4,69,000.00
2.3 NSR 28.6 mm O.D.(insulation : 19 mm) 200.00 Rm 1,557.00 3,11,400.00
2.4 NSR 22.2 mm O.D.(insulation : 13 mm) 155.00 Rm 1,314.00 2,03,670.00
2.5 NSR 19.1 mm O.D.(insulation : 13 mm) 654.00 Rm 1,024.00 6,69,696.00
2 Drain Piping
Providing and fixing of rigid PVC piping complete with fittings, supports as per
specifications and duly insulated with 6 mm thick XLPE polythylene insulation as
per specification and drawings.
2.1 NSR 50 mm dia 150.00 Rm 374.00 56,100.00
2.2 NSR 40 mm dia 412.00 Rm 284.00 1,17,008.00
2.3 NSR 32 mm dia 1,050.00 Rm 256.00 2,68,800.00
2.4 NSR 25 mm dia 275.00 Rm 193.00 53,075.00
"SUB-TOTAL-SH-II" 44,68,349.00
SH-III VENTILATION
1 Inline Fans
Providing, fixing, testing and commissioning of inline fans of G.I. construction,
complete with centrifugal fan with motor, canvass connection at inlet & outlet
complete with MCB & relays, cabling & earthing (with 5 Rm) as per specification
and drawings.
1.1 NSR 500 cfm @ 20 MM Static Pressure 16.00 Nos. 15,650.00 2,50,400.00
1.2 NSR 400 cfm @ 15 MM Static Pressure 16.00 Nos. 14,460.00 2,31,360.00
2 Propellar Fans
Providing, fixing, testing and commissioning of Propellar fans of complete with
centrifugal fan with motor, as per specification and drawings.
2.1 NSR 100 mm dia 6.00 Nos. 2,095.00 12,570.00
"SUB-TOTAL-SH-III" 11,15,610.00
1 Ducting
2 NSR Providing, fixing, testing and commissioning of site made ducting along with all
supports, hangers, vanes, splitters, neoprone gasket for zero leakage as per
specification and drawings.
G.I. Sheet Metal Ducting (Rectangular)
2.1 NSR 0.63 mm (24 Ga) 1,850.00 Sqm 665.00 12,30,250.00
2.2 NSR 0.80 mm (22 Ga) 650.00 Sqm 754.00 4,90,100.00
2.3 NSR 1.00 mm ( 20 Ga) - Sqm -
2.4 NSR 1.2 mm ( 18 GA) - Sqm -
Insulation
3 NSR Providing and fixing of XLPE polythylene / nitrile rubber insulation with proper
adhesive on ducts complete as per specifications and drawings.
3.1 NSR 19 mm thk 1,150.00 Sqm 843.00 9,69,450.00
6 Grilles/Diffusers
Providing and fixing of aluminium extruded powder coated supply and return air
grilles/diffusers as per specifications and drawings including fixing frame in false
ceiling/walls as per specification and drawings.(Colour approval from Arch.)
6.1 NSR Aluminium supply grill with damper. 25.00 Sqm 7,545.00 1,88,625.00
6.2 NSR Aluminium return grill without damper. 15.00 Sqm 5,770.00 86,550.00
6.3 NSR Aluminium supply Diffusers with damper. 5.00 sqm 9,320.00 46,600.00
6.4 NSR Aluminium return Diffusers without damper. 5.00 sqm 7,545.00 37,725.00
10 NSR Providing and fixing of XLPE polythylene / nitrile rubber UNDERDECK insulation 1,400.00 Sqm 632.00 8,84,800.00
with proper adhesive on SLABS/BEAMS complete as per specifications and
drawings ON EXPOSED ROOF LEVEL .
1 ELECTRICAL PANEL
Desgn,fabrication,assemble,wiring and supply of front operated cubicle type
compartmentalized, front access free standing, dust and vermin proof main
switchnoards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system
suitable for fault level of required value symmetrical at 415 volts,fabricated from 2
mm thick CRCA MS sheets with hinged, gaketted and lockable doors of 1.6 mm
thick having sturctural reinforcement with suitable angle/channel/T/flat sections
including 3 mm thick gland plates on top and bottom and including GI earth strip
of required size with 2 nos earthing terminals and including powder coated paint
finish of approved shade over metal surface cleaned and treated with seven tank
process complete with interconnections etc. as per specifications. as required.
and as below.
1.2 NSR MCC-2(ADMIN BLOCK FIRST FLOOR) 1.00 Set 1,80,530.00 1,80,530.00
Incoming
1 No 250 amps, 35 KA, TPN MCCB thermal magnetic release for short circuit,
O/C and E/F protection with adjustable setting as per specification suitable to
receive armoured cable.
i. 0-500 volts Digital voltmeter with selector switch and protection fuses. - 1 Set
ii. 0-300 amps, ammeter. with CT's ratio and selector switch- 1 Set
iii. Phase indicating lamps with MCB's Protection. 3 Sets
Main bus bar rated at 300 amps 4 pole, 25 KA with heat shrinkable sleeve and
shall be of aluminium.
OUTGOING
2Nos. 100 amps TPN MCCB as Outgoing for 1 No. of 60 HP & 1 No. for 56 HP
Machine .
1 Nos. Spare space for 100 amps MCCB rating Outgoing.
1.3 NSR MCC-3(ADMIN BLOCK SECOND FLOOR) 1.00 Set 1,34,528.00 1,34,528.00
Incoming
1 No 300 amps, 35 KA, TPN MCCB thermal magnetic release for short circuit,
O/C and E/F protection with adjustable setting as per specification suitable to
receive armoured cable.
1.4 NSR MCC-3(ADMIN BLOCK THIRED FLOOR) 1.00 Set 2,17,070.00 2,17,070.00
Incoming
1 No 250 amps, 35 KA, TPN MCCB thermal magnetic release for short circuit,
O/C and E/F protection with adjustable setting as per specification suitable to
receive armoured cable.
i. 0-500 volts Digital voltmeter with selector switch and protection fuses. - 1 Set
ii. 0-300 amps, ammeter. with CT's ratio and selector switch- 1 Set
iii. Phase indicating lamps with MCB's Protection. 3 Sets
Main bus bar rated at 300 amps 4 pole, 25 KA with heat shrinkable sleeve and
OUTGOING
2 Nos. 100 amps TPN MCCB as Outgoing for 2 No. of 50 HP Machine AND 1
NO. 63 AMPS TPN MCCB as outgoing for 32 H.P Machine.
1 Nos. Spare space for 100 amps MCCB rating Outgoing.
Cable/Pipe Tray
2 Providing and fixing of cable/pipe tray for running refrigerant piping and cable
alongwith control wiring etc. tray should be properly clamped and hang with all
connected accessories and it should be of following sizes.
2.1 NSR 300 x 50 x 2 mm (Thickness) 350.00 Rm 588.00 2,05,800.00
2.2 NSR 150 x 50 x 2 mm (Thickness) 250.00 Rm 373.00 93,250.00
Earthing
5 Providing & fixing of double loop earthing on surface or in rececess with GI for
loop earthing complete as per specifications & as required of following sizes :
5.1 NSR 25 x 3 mm GI Strip 300.00 RMTR 95.00 28,500.00
5.2 NSR 8 SWG dia. GI wire 200.00 RMTR 59.00 11,800.00
5.3 NSR 6 SWG dia. GI wire R.O RMTR
SECTION - I- PASSIVE
1 NS Supply , Installtion , Testing and comissioning of armoured 6 core mtr 1500 136.00 2,04,000.00
multimode OFC cable for interfloor switch connectivity
2 NS Supply , Installtion , Testing and comissioning of 12 port loaded LIU with Nos 10 14,037.00 1,40,370.00
adaptor plates , pigtel cables for connections
3 NS Supply, Installtion , Testing and comissioning of 24 port loaded LIU for Nos 5 32,773.00 1,63,865.00
core switch to access switch connectivity over fiber
4 NS Supply, Installtion , Testing and comissioning of SC-LC multimode fiber Nos 96 2,410.00 2,31,360.00
patch cord
5 NS Supply , Installtion , Testing and comissioning of LC-LC multimode fiber Nos RO 2410.00 -
patch cord
6 NS Supply , Installtion , Testing and comissioning of CAT 6 UTP cable solid mtr 49100 32.00 15,71,200.00
copper conductors
7 NS Supply installation testing and commissioning category 6 Series I/Os with Nos 720 280.00 2,01,600.00
Toolless mechanism for Data & Voice
8 NS Supply , Installtion , Testing and comissioning of loaded 24 port CAT6 Nos 35 9,447.00 3,30,645.00
jack panel with Toolless mechanism for Data & Voice
9 NS Supply , Installtion , Testing and comissioning of CAT6 patch cord 3 feet Nos 720 299.00 2,15,280.00
for rack side switch termination For Data & Voice
10 NS Supply , Installtion , Testing and comissioning of CAT6 patch cord 7 feet Nos 720 386.00 2,77,920.00
for user termination to information outlet For Data & Voice
11 NS Supply , Installtion , Testing and comissioning of 1 or 2 port face plate Nos 720 154.00 1,10,880.00
white for I/O fixing at user side For Data & Voice
12 NS Supply , Installtion , Testing and comissioning of 15 U wall mount rack Nos 17 13,015.00 2,21,255.00
with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts
For Data & Voice
13 NS Supply, Installtion , Testing and comissioning of 42 U (600W/ 1000D) floor Nos 2 60,825.00 1,21,650.00
mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of
hardware pkts
FAULT ISOLATOR
3 NS Supply, installing, testing and commissioning of addressable type Fault Nos. 27 4,888.00 1,31,976.00
Isolators for isolating shorted, de wired and loose circuits between two
successive fault isolators with automatic resetting arrangement.
CONTROL MODULES
4 NS Supply, installing, testing and commissioning of addressable and Nos. 16 5,666.00 90,656.00
automatic commandable control modules for:
Hooters Circuit
Sounders
5 NS Supply, Installation, Testing and Commissioning of Sounders with strobe Nos. 16 4,000.00 64,000.00
(UL 9th Edition Approved and NFPA compliant) complete as required.
REPEATER PANEL
7 NS Supply, installing, testing and commissioning of Repeator panel with No. 1 195529.00 1,95,529.00
minimum 80 character LCD Display complete with accessories as
required.
PA CONTROLLER
8 NS SITC of 4 zone IP based, digital Voice Alarm controller expandable upto 8 Nos. 1 3,49,953.00 3,49,953.00
zones. The voice alarm controller should be able to connect directly over
Ethernet. It should have functions like the audio playing, zone control, fault
monitoring, log recording, volume control and amplifier switchover. The
Voice alarm controller should also have the following functions:
. 255 Priorities
. Time schedule broadcasts
. Capable of amplifier redundancy
. 4 trigger inputs/outputs
DIGITAL AMPLIFIERS
9 NS SITC of 1X500W Class-D Amplifier with 1 independent channel and can Nos. 3 2,36,968.00 7,10,904.00
provide automatic re-settable overcurrent, overload, overheating,
overvoltage, under-voltage and DC protection
500 Watts
PAGING STATION
11 NS SITC of IP based Networkable touch screen paging station for selection of Nos. 1 85,877.00 85,877.00
zones, supervision of system status, setting of scheduled broadcasts with
12 NS Supply & laying of Fire Survival Armoured cable (HPSR) High RM RO 126.00 -
Performance Silica Rubber, size 1.5 sq mm x 2 core Copper, as per BS
7629 code, LPCB certified, 950C rating for three hours for fire alarm
system
13 NS Supply, Installation, Testing and Commissioning of the GUI based main Nos 1 3,50,508.00 3,50,508.00
network Fire Detection, Digital PAVA and 2 way communication common
software which must be capable of graphically representing each facility
being monitored with floor plans and icons depicting the actual locations of
the various systems; and / or sensors locations. The GUI software shall be
located in control room on the ground floor and shall monitor all the Floor
Fire Detection, Digital PAVA and 2 way communication panel connected
with each other. The software shall provide the facility to Monitor, Control
all the Digital PAVA as well as 2 way communication from main control
room using voice signals over Fire Network along with the Fire detection
signal. (UL 9th Edition Approved and NFPA compliant) complete as
required. The cost will also include the latest PC with the follwing
configuration.
14 NS Supply, installing, testing and commissioning of 2 way communication Fire Nos 8 10,500.00 84,000.00
Fighter's Telephone Jack
15 NS Supply, installing, testing and commissioning of 2 way communication Fire Nos 16 26,500.00 4,24,000.00
Fighter's Handset
2 18.34 Constructing masonry Chamber 90X90X100 cm, inside with 75 class designation
brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I.
surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep
(inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4
graded stone sggregate 20 mm nominal size) necessary excavation foundation
concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse
sand) 12 mm thick finished with a floating coat of neat cement complete as per
standard design:
2.1 18.34.1 With common burnt clay F.P.S (non modular) bricks of classs designation 7.5 Each 11.00 11,672.35 1,28,396.00
2 NS Supplying, Installing, testing and commissioning offire hydrant multi stage Set 1.00 5,59,400.00 5,59,400.00
pump capable of delivering 2850 Lpm @ 70.0m head coupled to water
coiled diesel engine of adequiate HP. It shall be fitted with a radiator on a
common base frame with complete ancilalary units such as calling system,
non return value, Y strainers, fuel tank of 200 lts capacity. Pressure guage,
pressure switch, cables, earth strip etc. Control panel shall be per specification
stated in item No.105. (Cost of control pannel is not included)
3 NS Supplying, Installing, testing and commisioning electrically driven jockey Nos 1.00 96,800.00 96,800.00
pump of capacity 180 Lpm at 75.0m head with all the necessary
accessories viz. Pressure guages etc., operating on 3Ph 50Hz, 400/440 V AC
supply including foundation, bolts, earth strip etc.,Control panel shall be per
specification stated in item No.105. (Cost of control pannel is not included)
4 NS Supply installing, testing and commissioning of COMMON control panel for Nos 1.00 20,200.00 20,200.00
firefighting system consisting of one Diesel engine as common standby & electrical
motor driven 60 HP Main fire pump, 35 HP sprinkler pump and Jockey pump of
12.5 HP consisting of the following:
INCOMING:
1 No. 230 Amps MCCB
1 No. Set of 400 Amps. TPN AL. Bus bars
1 No. 0-250 Amps. Ammeter, 1No. 0-500V voltmeter with phase selector switch,
etc. complete
OUTGOING for Main Electric Hydrant Pump:
Remote starting controlling through pressure switch
1 No. 125 Amps MCCB
1 No. star delta starter suitable for 60 HP
5 NS Providing and fixing Dual plate (Wafer type) check valve (non return valve) of Class
PN 16, having cast iron body, stainless steel disc (AISI 316), trim and spring of
approved make. including a set of MS flanges, required nos. of nut & bolts all
complete.
a) 150 mm dia Nos 4.00 6,314.00 25,256.00
b) 100 mm dia Nos 11.00 4,560.00 50,160.00
c) 80 mm dia Nos 1.00 3,134.00 3,134.00
8 NS SITC of 63mm dia single headed Gun metal Hydrant value with black cap and Nos. 100.00 7,930.00 7,93,000.00
wheet as per IS 5290 etc., complete Make: WINCO / NEW Age.
9 NS SITC of Hose cabinet made out of 18 gauge M.S. Sheet with double glass door Nos. 64.00 4,372.00 2,79,808.00
with locking arrangement and painted with two coats of Fire red Enamel paint at
outer side of the box and two coats of white enamel paint at inner side of
the box is to accommodate 2 nos. of Fire hose. box size 20"x24"x 1 0"
10 NS Providing and fixing two way fire service inlet to the 100mm dia GI 'C' class pipe Nos. 11.00 22,672.00 2,49,392.00
wet riser to be house in MS bolt with glass cover for front side.etc. complete.
11 NS Providing and fixing Four way fire service inlet to the 100mm dia GI 'C' class pipe Nos. 2.00 28,667.00 57,334.00
wet riser to be house in MS bolt with glass cover for front side.etc. complete.
12 NS Providing and fixing dual type pressure switch suitable for 1-10kg/m2 Nos. 3.00 7,660.00 22,980.00
including electrical connection setting of cut-in and cut off pressure complete in all
respects etc. complete.
13 NS Providing and fixing dial type pressure gauge with isolation cock and Nos. 5.00 3,385.00 16,925.00
chromeplated copper pipe etc complete
100mm dia calibration 0-10 kg/sq.cm
Fire Extinguishers
15 NS Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S Nos. 64.00 11,070.00 7,08,480.00
cylinderical body,squeeze lever discharge valve fitted with internal dischargetube,
30cms long high pressure discharge hose, discharge nozzle, suspension bracket,
confirming to IS : 934 finished externally with red enamel paint and fixed to wall
with brackets with rawl plug/dash fasteners complete with internal charge. Capacity
4.5 kg. I.S.I. Marked.
16 NS Providing 9 Ltr Fire Extinguisher, AFFF Foam Type, Stored Pressure Type, Nos. 2.00 5,368.00 10,736.00
Pressure Gouge, Gross Wreight 14.6 Kg, empty Weight 5.6Kg, Can Height
611 MM Diameter 175 MM, Discharge Time Less than 60 Sees, Controllable
discharge mechanism, Range minimum 6 Meters, Applicable on Class A,8&C
A Rating 13A, 8 Rating 558, Can Constrution . Deep drawn & Co, Mig welded,
Valve construction; Forging & Machining, Internal Coating of Can : Epoxy
Powder coatingm, External Coating of Can : Epoxy Polyster Powder coating,
sheet metal thickness, 2.0 MM, lSI and EN Approved, Helium Leak Detection
Tested, 1 Year Warranty.
Capacity : 9 Litres
Fire Hose
18 NS SITC of RRL Fire hose of 63mm dia 15m length as per IS 84.23 binded with one Nos. 200.00 8,134.00 16,26,800.00
set of male and female lnstantainious Gun metal couping as per IS 903
WINCO/NEW AGE
Hose Reel
19 NS SITC of Hose reel cane M.S. Pressed reel of 600mm dia and swing upto 170 - Nos. 53.00 4,880.00 2,58,640.00
degree with "L" shape carrier
20 NS SITC of 19mm dia with wire binded Nylon hose. length of 36.5 mtrs. Nos. 53.00 5,287.00 2,80,211.00
21 NS SITC of Gun metal AIR RELEASE VALVE SIZE OF 25mm dia Nos. 11.00 2,135.00 23,485.00
22 NS Excavation in all sorts of soil for laying pipes upto 2OOmm dia including cum 610.80 152.00 92,842.00
forming bottom surface to required level, refilling selected excavated earth around
the pipe in layers of 150mm thick, watering consolidating and disposing off
the surplus earath within the sties or as directed by the site engineer etc.,
complete Depth upto 1.0m.
23 NS Providing and fixing in positionGM gate valve with C.l wheel of approved Nos. 70.00 695.00 48,650.00
quality (screwed end) 50mm nominal bore including cost of all materials, labour
and HOM of equipments with all leads complete as per specifications.
24 NS Y ' Strainer - CI `Y' strainer with bronze perforated sheet basket including
rubber gasket, flanges, nuts, bolts and washers, complete as required.
25 NS Designing, providing and fixing Orifice plate made out of stainless steel
plate (thickness as per specification) for following size of pipe to reduce pressure
upto 3.5 Kg/sqcm complete in all respects.
a) 80mm dia 106.00 2,070.00 2,19,420.00
27 NS Supplying and fixing Air vessel 300mm dia inlet, 25mm drain, 25mm dia connection Nos. 1.00 31,410.00 31,410.00
for air release valve including legs, painting with red oxide primer and finished
with fire red enamel paint. It shall be inclusive of all relevent pipes, valves, specials
upto pump header and other accessaries as per local fire brigade standard.
28 NS Supplying and fixing MS Cabinet (size 600 x 450 x 150mm) fabricated from 16 Nos. 42.00 4,370.00 1,83,540.00
gauge M.S.Sheet with full front glass door and locking arrangement for
placing spare sprinklers including fire man axe.
29 NS Providing & fixing butterfly valve (Body : Grey Cast Iron, Shaft : SS, Disc : SG
Iron (Rilson coated), Liner : HT - EPDM) (upto 150mm dia with hand lever
operation & above with gear box operation). Tested to a pressure not less
than 15 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers &
painting complete as required.
80mm nominal dia Nos. 44.00 3,445.00 1,51,580.00
100mm nominal dia Nos. 1.00 4,110.00 4,110.00
150mm nominal dia Nos. 8.00 5,185.00 41,480.00
200mm nominal dia Nos. 2.00 8,997.00 17,994.00
2.0 NS Supply, Installation,Testing & Commisioning of Fire Graphics Software Set - 9,01,710.00 -
Winmag to be loaded on PC to monitor the Floor wise Fire Detection
System.
3.0 NS Supply, Installation, Testing & Commissioning of UL Listed and FM Set - 88,810.00 -
approved active repeater panel. The panel shall be able to give location of all
fire and fault and Isolation conditions of addressable units of main Fire Alarm
panel via the address codes and also having remote-system- control
capabilities. The panel shall have a 2x4-3/4 Size VGA monochrome
LCD display and having maximum 320 (8 x 40) Characters in the display and
complete as required as per specification.
4.0 NS Supply, Installation,Testing & Commisioning of Analog Addressable Nos. 600.00 2,445.00 14,67,000.00
Intelligent multisensor detector with two inbuilt optical smoke sensors with light
angles as well as additional heat detector sensor with decentralise
intelligence, soft addressable Photothermal type with inbuilt fault isolator as
5.0 NS SITC of 2x1.5 Sq.mm copper armoured cable with Termination etc . Nos. 700.00 154.00 1,07,800.00
6.0 NS Supply, Installation, Testing & Commisioning of Analogue Addressable Nos. 4.00 2,447.00 9,788.00
Intelligent Heat Detector with fixed & rate of rise temperature function with
decentralise intelligence , soft addressable type, with inbuilt fault isolator as
per NFPA style 7 wiring complete with base as required.
7.0 NS Supply, Installation, Testing & Commissioning of UL listed and FM Nos. 23.00 2,538.00 58,374.00
approved Manual Pull Station complete as required as per specification.
8.0 NS Supply, installation, testing and commissioning of addressable control module Nos. 11.00 2,447.00 26,917.00
complete as per specification.
9.0 NS Supply, installation, testing and commissioning of addressable monitor module Nos. 12.00 2,537.00 30,444.00
complete as per specification.
10.0 NS Supply Installation, Testing & Commissioning of wall mounting loop Nos. 25.00 2,899.00 72,475.00
powered addressable type hooter with all accessories.
11.0 NS Supply Installation, Testing & Commissioning of Response Indicator single LED / 2 Nos. 306.00 158.00 48,348.00
LED.
1.0 NS Supply, Lowering, installation & testing of KSB make submersible pumping set 2.00 Each 61,500.00 1,23,000.00
with 7.5 HP motor 4 stage pump suitable for 20 / 26 / 30 / 38 / 40 / 45 / 50 m3 hr.
at 42 / 38 / 36 / 32 / 29 / 25 / 20 mtr. Head respectively. With Three Phase.
(Model: 273/4)
2.0 NS Providing & fixing cable 6 sq.mm. From submersible pump to panel board. 140.00 Metre 140.00 19,600.00
3.0 NS Providing & fixing Panel Board for submersible pump fitted with DOL 2.00 Each 9,800.00 19,600.00
starter ammeter, voltmeter single phase preventer standard/indo/cop
make MCB of off switch push bottom duly wired and made out of 16/18 SWG
sheet.
1.0 Supply, installation, testing & commissioning of vertical inline multistage pumping
set (Imported) with Stainless steel-304 body, Stainless steel-304 impeller,
Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with
mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10%
volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with
gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm
I section base plate bolted to cement concrete foundations complete.Vendor to
submit performance curves and technical catalogue of the proposed model for
review and information.
A In Water Supply Pump Room
1.1 NS Filter Feed Pump (Dom. Water) 1.00 Set 2,80,000.00 2,80,000.00
Set of Three Pumps ( 2 Working+ 1 Standby)
Capacity 5.0 lps
Head 25 m
1.2 NS Water Make up Pump to STP Area 1.00 Set 1,70,000.00 1,70,000.00
Set of Two Pumps( 1 Working+ 1 Standby)
Capacity 5.0 lps
Head 30 m
HP 5 HP Approxi
3.0 Supply, installing, testing and commissioning of submersible single stage single
entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to
TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power
supply with mechanical seal, pump connector unit with rubber diaphram and
bend, vertical discharge pipe, guide pipe and chain in built level controller,
sequence running controller, dry running Protection complete in all respects.
(Pumps shall be installed in a set of two pumps One working and One
standby)
3.1 NS Water Supply Pump 1.00 Set 1,05,000.00 1,05,000.00
(Pumps to be suitable to handle solids upto 12 mm size)
Capacity - 4.0 LPS (Each)
Head - 10 M
H.P. - 1.5 HP Approx.
5.0 Providing and fixing galvanized slotted cable trays supported from ceiling at
intervals of 60 cms on both ends including cable clips with nuts and bolts
welding of support rods with ceiling inserts or by drilling and installing expandable
fasteners, cutting and making good complete
5.1 NS 300 mm wide (for horizontal at ceiling level) 50.00 Metre 850.00 42,500.00
5.2 NS 150 mm wide (For vertical drops) 50.00 Metre 650.00 32,500.00
6.0 NS Providing and fixing motor control centre fabricated from 14g M.S. sheet with
stove enamelled finish and comprising of :-
For Water Supply Pumps (At Pump Room)
Incoming:-
One incoming main TPN MCCB of 200 amp, 35KA required rating.
Fully taped aluminum TPN 200 Amp. bus bar of required capacity in a
separate bus bar chamber
1 no. voltmeter with VSS.
3 Nos. LED type Phase indication lamps (R,Y,B) with 2A control MCB
one set of LED type ON, OFF indication lamps. (R,G)
Outgoings:-
03 No. TPN MCCB of 125 A with 25 KA service breaking capacity for
domestic water hydropneumatic pumps. (Only connection to inbuilt panel
of Domestic water hydropneumatic system)
01 Nos. Amp meters with (0-160 A) with required CT ratio and 2A control MCB,
LED type ON/OFF/Trip indication lamps with auto manual selector switch.
07 Nos. TPN MCB of 32 A with 10 KA service breaking capacity for filter feed
pumps, water make up pumps to STP area & sump pumps 2.0/7.5 HP motor.
07 Nos. Amp meters with (0- 50 A) with required CT ratio and 2A control MCB,
LED type ON/OFF/Trip indication lamps with auto manual selector switch.
07 Nos. Auto DOL Starter for 2.0-7.5 HP motor. Each shall have Auto/
Manual selector switch, over load relay, single phasing preventor,
ON/OFF/ Trip indication lamps, ON/OFF push Buttons, contactor and
suitable No. of Potential free contacts for remote / local operations,
indication & interlocking and Building Management system.
10.0 Supply of skid mounted fully automatic Reverse Osmosis System of output
capacity 150 litres / hour designed at a minimum Flux at inlet complete as
required with the following items:
Garnet Filter (GF) - 1 No.
Media for GF - 1 LOT
Antiscalant Dosing System with level sensors - 1 Lot
Cartridge Filter - 1 No.
High pressure pump - 2 Nos (1W + 1St).
R.O. Block - 1 No.
1.0 Sewage Treatment Plant Based on Advance MBBR (Moving Bed Bio
Reactor) Technology :
Design, supply installation, testing, commissioning and approval from
pollution control board of Sewage treatment Plant of 250 KLD including
preparation of report / drawing as per pollution control board requirement,
arrangement of raw sewage for testing and commissioning (Excluding
excavation, back filling & disposal of surplus earth and any type of Civil
construction work) for the following duty:
Nature of effluent - Domestic Sewage from toilets/kitchen use.
Flow Rate -250 KLD
Sewage Incoming Characteristics
pH - 6.5 - 8.5
BOD5 - upto 250 - 400 Mg/L
S. Solid - 200 to 500 Mg/L
COD 5 - Upto 600 Mg/L
Oil & Grease - 50 Mg/L
3.0 NS Supply, installation, testing & commissioning of magnetic type flow meter at the 1.00 Each 75,000.00 75,000.00
outlet point of raw sewage transfer pump of 80 mm size suitable for 0 - 50 KLH
flow.
4.0 Supply, installation, testing & commissioning of twin type rotary air blower with
accoustic encloser, driven through V belt or directly coupled through flexible
coupling to a TEFC motor of suitable HP Suitable for 415 10% volts, 3 phase,
50 cycles A/C supply.
4.1 NS Capable of delivering 300 cum/hr of free air at 0.5 kg/cm2. 2.00 Each 1,85,000.00 3,70,000.00
5.0 NS Supply, installation, testing & commissioning of Air piping shall comprise of pipes 1.00 Lot 1,45,000.00 1,45,000.00
droppers/ laterals with M S (epoxy coated) Header complete with all fittings such
as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle
flanges etc including cutting holes in wall, makes chases in wall and making
good the same. Contactor to submit detailed P&I indicating their proposal.
7.0 NS Supply, installation, testing & commissioning of coarse air diffusers 1.00 Lot 40,000.00 40,000.00
capable of delivering 3-6 cum/hr in equalization tank and sludge holding tank
for providing areation.
8.0 NS Supply, installation, testing and commissioning of PVC tube deck settling media 1.00 Job 1,45,000.00 1,45,000.00
to be installed in Tube Settling Tank. The Media to be supported on MSEP frame
with baffle plate & overflow launder.
9.0 NS Controllers with low voltage relays, stainless steel probes and pvc shroud, control 1.00 Set 18,000.00 18,000.00
cabling as required length. (No of probes as required for function of each
controller).
Drainage Sump Pumps level controller
To cut off duty pump on low water level in the sump and to start one pump when
high level in the sump and start both pumps when sump is over flowing.
15.0 NS Solenoid Valves for automatic operation of the complete system 1.00 Set 41,000.00 41,000.00
16.0 NS Electrical Panel for the complete system 1.00 Set 1,45,000.00 1,45,000.00
17.0 NS Piping and Valves - UPVC / CPVC SCH 10 1.00 Job 76,000.00 76,000.00
18.0 NS Skid for the complete system in SS 304 1.00 Job 52,000.00 52,000.00
19.0 NS Backwash Tank of capacity 5000 Litre including drain, overflow connection 1.00 Set 74,000.00 74,000.00
20.0 NS Supply, installation, testing & commissioning of metering pump type 1.00 Each 30,000.00 30,000.00
chemical doser with motorize ajector, shaft & blade SS 304 material with 100 lits.
PVC/HDPE solution tank, injection fitting assembly, suction and delivery
hose upto the point of injection, capacity 0-6 lph, complete in all respects.
23.0 NS Supply, installation, testing & commissioning of Filter Press of Plate size 24" x 1.00 Set 4,10,000.00 4,60,000.00
24" x 18 Nos. plate with Screw feed pumps of 2 M3/Hr @ 40 M head
capacity (1 working + 1 standby) complete in all respects.
24.0 NS Approval from pollution control board at initial & various other stages of 1.00 Job 1,75,000.00 1,75,000.00
works including preparation of report / drawings as per pollution control
board requirement, arrangement of raw sewage for testing &
commissioning. Contractor shall include the cost of all chemicals
(consumed during testing & commissioning and the cost of such items of works
which are not explicitly mentioned above, but are mandatory to have pollution
board approval.
Notes :
a) All MCCBs / MCBs shall be of 15 KA breaking capacity and suitable for motor
duty application.
b) All motor starters shall be provided with Automatic level controller.
c) DOL starters shall be used for motors below 10HP and Star-Delta Starters for
other motors .
d) Provision shall be made for providing potential free contacts to all pumps starters.
MCC for all STP equipments / pumps as described above. 1.00 Job 7,25,000.00 7,25,000.00