Professional Documents
Culture Documents
8 HVDC - Chap11
8 HVDC - Chap11
High Voltage
Direct Current Transmission
Power Transmission was initially carried out in the early 1880s using Direct Current (d.c.). With the
availability of transformers (for stepping up the voltage for transmission over long distances and for stepping
down the voltage for safe use), the development of robust induction motor (to serve the users of rotary power),
the availability of the superior synchronous generator, and the facilities of converting a.c. to d.c. when
required, a.c. gradually replaced d.c. However in 1928, arising out of the introduction of grid control to the
mercury vapour rectifier around 1903, electronic devices began to show real prospects for high voltage direct
current (HVDC) transmission, because of the ability of these devices for rectification and inversion. The most
significant contribution to HVDC came when the Gotland Scheme in Sweden was commissioned in 1954 to be
the World's first commercial HVDC transmission system. This was capable of transmitting 20 MW of power
at a voltage of -100 kV and consisted of a single 96 km cable with sea return.
With the fast development of converters (rectifiers and inverters) at higher voltages and larger currents, d.c.
transmission has become a major factor in the planning of the power transmission. In the beginning all HVDC
schemes used mercury arc valves, invariably single phase in construction, in contrast to the low voltage
polyphase units used for industrial application. About 1960 control electrodes were added to silicon diodes,
giving silicon-controlled-rectifiers (SCRs or Thyristors).
In 1961 the cross channel link between England and France was put into operation. The a.c. systems were
connected by two single conductor submarine cables (64km) at 100kV with two bridges each rated at 80
MW. The mid-point of the converters was grounded at one terminal only so as not to permit ground currents to
flow. Sea return was not used because of its effect on the navigation of ships using compasses. The link is an
asynchronous link between the two systems with the same nominal frequency (60Hz).
The Sakuma Frequency Changer which was put into operation in 1965, interconnects the 50Hz and the 60Hz
systems of Japan. It is the first d.c. link of zero length, and is confined to a single station. It is capable of
transmitting 300 MW in either direction at a voltage of 250 kV.
In 1968 the Vancouver Island scheme was operated at +250 kV to supply 300 MW and is the first d.c. link
operating in parallel with an a.c. link.
In 1970 a solid state addition (Thyristors) was made to the Gotland scheme with a rating of 30MW at -
150kV.
Also in 1970 the Kingsnorth scheme in England was operated on an experimental basis. In this scheme
transmission of power by underground d.c. cable at 200 kV, 640 MW is used to reinforce the a.c. system
without increasing the interrupting duty of a.c. circuit breakers.
The first converter station using exclusively Thyristors was the Eel River scheme in Canada. Commissioned in
1972, it supplies 320 MW at 80 kV d.c. The link is of zero length and connects two a.c. systems of the same
nominal frequency (60Hz).
High Voltage Direct Current Transmission 185
The largest thyristors used in converter valves have blocking voltages of the order of kilovolts and currents of
the order 100s of amperes. In order to obtain higher voltages the thyristor valve uses a single series string of
these thyristors. With higher current ratings required, the valve utilizes thyristors directly connected in parallel
on a common heat sink.
The largest operational converter stations have ratings of the order of gigawatts and operate at voltages of 100s
of kilovolts, and maybe up to 1000 km in length.
The thyristors are mostly air cooled but may be oil cooled, water cooled or Freon cooled. With air cooled and
oil cooled thyristors the same medium is used as insulant. With the Freon cooled thyristors, SF6 may be used
for insulation, leading to the design of a compact thyristor valve.
Unlike an a.c. transmission line which requires a transformer at each end, a d.c. transmission line requires a
convertor at each end. At the sending end rectification is carried out, where as at the receiving end inversion is
carried out.
The capabilities of power transmission of an a.c. link and a d.c. link are different.
For the same insulation, the direct voltage Vd is equal to the peak value (2 x rms value) of the alternating
voltage Vd.
Vd = 2 Va
For the same conductor size, the same current can transmitted with both d.c. and a.c. if skin effect is not
considered.
Id = Ia
Thus the corresponding power transmission using 2 conductors with d.c. and a.c. are as follows.
The greater power transmission with d.c. over a.c. is given by the ratio of powers.
H
Pd = _2__ = GDWSI XQLW\
Pa cos 3 GDWSI
J
In practice, a.c. transmission is carried out using either single circuit or double circuit 3 phase transmission
using 3 or 6 conductors. In such a case the above ratio for power must be multiplied by 2/3 or by 4/3.
In general, we are interested in transmitting a given quantity of power at a given insulation level, at a given
efficiency of transmission. Thus for the same power transmitted P, same losses PL and same peak voltage V,
we can determine the reduction of conductor cross-section Ad over Aa.
186 High Voltage Engineering - J R Lucas, 2001
Let Rd and Ra be the corresponding values of conductor resistance for d.c. and a.c. respectively, neglecting skin
resistance.
[2P/(Vm cos3@ Ra
2
power loss PL =
In the case of hvdc transmission, ground return (especially submarine crossing) may be used, as in the case of a
monopolar d.c. link. Also the single circuit bipolar d.c. link is more reliable, than the corresponding a.c. link,
as in the event of a fault on one conductor, the other conductor can continue to operate at reduced power with
ground return. For the same length of transmission, the impedance of the ground path is much less for d.c. than
for the corresponding a.c. because d.c. spreads over a much larger width and depth. In fact, in the case of d.c.
the ground path resistance is almost entirely dependant on the earth electrode resistance at the two ends of the
line, rather than on the line length. However it must be borne in mind that ground return has the following
disadvantages. The ground currents cause electrolytic corrosion of buried metals, interfere with the operation
of signalling and ships' compasses, and can cause dangerous step and touch potentials.
The d.c. insulation level for the same power transmission is likely to be lower than the corresponding a.c. level.
Also the d.c. line will only need two conductors whereas three conductors (if not six to obtain the same
reliability) are required for a.c. Thus both electrical and mechanical considerations dictate a smaller tower.
In contrast to the overhead line, in the cable breakdown occurs by puncture and not by external flashover.
Mainly due to the absence of ionic motion, the working stress of the d.c. cable insulation may be 3 to 4 times
higher than under a.c.
High Voltage Direct Current Transmission 187
Also, the absence of continuous charging current in a d.c. cable permits higher active power transfer, especially
over long lengths.
(Charging current of the order of 6 A/km for 132 kV). Critical length at 132 kV 80 km for a.c cable. Beyond
the critical length no power can be transmitted without series compensation in a.c. lines. Thus derating which
is required in a.c. cables, thus does not limit the length of transmission in d.c.
A comparison made between d.c. and a.c. for the transmission of about 1550 MVA is as follows. Six number
a.c. 275 kV cables, in two groups of 3 cables in horizontal formation, require a total trench width of 5.2 m,
whereas for two number d.c. 500 kV cables with the same capacity require only a trench width of about 0.7 m.
Under a.c. conditions, the current is not uniformly distributed over the cross section of the conductor. The
current density is higher in the outer region (skin effect) and result in under utilisation of the conductor cross-
section. Skin effect under conditions of smooth d.c. is completely absent and hence there is a uniform current
in the conductor, and the conductor metal is better utilised.
Since corona loss increases with frequency (in fact it is known to be proportional to f+25), for a given
conductor diameter and applied voltage, there is much lower corona loss and hence more importantly less radio
interference with d.c. Due to this bundle conductors become unnecessary and hence give a substantial saving
in line costs. [Tests have also shown that bundle conductors would anyway not offer a significant advantage
for d.c as the lower reactance effect so beneficial for a.c is not applicable for d.c.]
The d.c. link is an asynchronous link and hence any a.c. supplied through converters or d.c. generation do not
have to be synchronised with the link. Hence the length of d.c. link is not governed by stability.
o
In a.c. links the phase angle between sending end and receiving end should not exceed 30 at full-load for
o
transient stability (maximum theoretical steady state limit is 90 ).
With a.c. links, interconnections between power systems must be synchronous. Thus different frequency
systems cannot be interconnected. Such systems can be easily interconnected through hvdc links. For different
frequency interconnections both convertors can be confined to the same station.
In addition, different power authorities may need to maintain different tolerances on their supplies, even though
nominally of the same frequency. This option is not available with a.c. With d.c. there is no such problem.
188 High Voltage Engineering - J R Lucas, 2001
When an a.c. transmission system is extended, the fault level of the whole system goes up, sometimes
necessitating the expensive replacement of circuit breakers with those of higher fault levels. This problem can
be overcome with hvdc as it does not contribute current to the a.c. short circuit beyond its rated current. In fact
it is possible to operate a d.c. link in "parallel" with an a.c. link to limit the fault level on an expansion. In the
event of a fault on the d.c line, after a momentary transient due to the discharge of the line capacitance, the
current is limited by automatic grid control. Also the d.c. line does not draw excessive current from the a.c.
system.
In the case of an a.c. tie line, the power cannot be easily controlled between the two systems. With d.c. tie
lines, the control is easily accomplished through grid control. In fact even the reversal of the power flow is just
as easy.
Expensive Convertor Stations are required at each end of a d.c. transmission link, whereas only transformer
stations are required in an a.c. link.
Convertors require much reactive power, both in rectification as well as in inversion. At each convertor the
reactive power consumed may be as much at 50% of the active power rating of the d.c. link. The reactive
power requirement is partly supplied by the filter capacitance, and partly by synchronous or static capacitors
that need to be installed for the purpose.
Convertors generate a lot of harmonics both on the d.c. side and on the a.c. side. Filters are used on the a.c.
side to reduce the amount of harmonics transferred to the a.c. system. On the d.c. system, smoothing reactors
are used. These components add to the cost of the convertor.
Due to the absence of a natural current zero with d.c., circuit breaking is difficult. This is not a major problem
in single hvdc link systems, as circuit breaking can be accomplished by a very rapid absorbing of the energy
back into the a.c. system. (The blocking action of thyristors is faster than the operation of mechanical circuit
breakers). However the lack of hvdc circuit breakers hampers multi-terminal operation.
Power is generally used at low voltage, but for reasons of efficiency must be transmitted at high voltage. The
absence of the equivalent of d.c. transformers makes it necessary for voltage transformation to carried out on
the a.c. side of the system and prevents a purely d.c. system being used.
High Voltage Direct Current Transmission 189
Due to the problems of commutation with d.c. machines, voltage, speed and size are limited. Thus
comparatively lower power can be generated with d.c.
The hvdc system has a lower line cost per unit length as compared to an equally reliable a.c. system due to the
lesser number of conductors and smaller tower size. However, the d.c. system needs two expensive convertor
stations which may cost around two to three times the corresponding a.c. transformer stations. Thus hvdc
transmission is not generally economical for short distances, unless other factors dictate otherwise. Economic
considerations call for a certain minimum transmission distance (break-even distance) before hvdc can be
considered competitive purely on cost.
Estimates for the break even distance of overhead lines are around 500 km with a wide variation about this
value depending on the magnitude of power transfer and the range of costs of lines and equipment. The break-
even distances are reducing with the progress made in the development of converting devices.
a.c.
cost/MW
80
d.c.
70
60
50
40
30
20
10
Figure 11.1 shows the comparative costs of d.c. links and a.c. links with distance, assuming a cost variation of
5% for the a.c. link and a variation of 10% for the d.c. link.
For cables, the break-even distance is much smaller than for overhead lines and is of the order of 25 km for
submarine cables and 50 km for underground cables.
190 High Voltage Engineering - J R Lucas, 2001
11.2 Convertor arrangements and operation
The three-phase six-valve bridge rectifier is almost exclusively used in high voltage direct current applications.
This is shown in figure 11.2.
+
choke
1 3 5
R
B 4 6 2
Y
The 6-valve bridge connection gives double the direct voltage as output compared to the simple 3-phase
rectifier. The convertor transformer may either be wound star-star as shown, or as star-delta (or even as delta-
0
star or delta-delta). The ripple of each of these connections is the same, but are phase shifted by 30 in output
with respect to each other. To obtain a smoother output, two bridges (one star-star and the other star-delta) may
be connected together to give the twelve pulse connection.
For the 6-valve bridge, with zero firing delay, the voltage waveforms across the thyristors are shown in figure
11.3. At any given instant, one thyristor valve on either side is conducting. The conducting period for the
thyristor valve R1 is shown on the diagram.
R1 Y3 B5 R1
Y6 B2 R4 Y6
The corresponding d.c. output voltage waveforms are shown in figure 11.4.
It can be shown that for the 6-valve bridge, the total r.m.s. ripple is of the order of 4.2% of the d.c. value (for
zero delay . DQG]HURFRPPXWDWLRQ 7KHULSSOHRIFRXUVHLQFUHDVHVZLWKWKHGHOD\DQJOHDQGKDVD
value oIDERXWDW.
High Voltage Direct Current Transmission 191
With the 12 pulse bridge, the r.m.s. ripple is of the order of 1.03% of the d.c. value (for . DQG DQG
LQFUHDVHVWRDERXWDW.
The use of a choke reduces the ripple appearing in the direct current transmitted.
If E is the r.m.s. line-to-line voltage, then if . WKHQWKHGLUHFWYROWDJHRXWSXWLVJLYHQE\HTXDWLRQ
(11.1).
E 3 3
V do = 2x x 2x cos d
2 - 3
3
3 2 1
= E. . 2 x sin
3 3
3 2
V do = . E = 1.350 E (11.1)
11.2.1 Control angle (Delay angle)
The control angle for rectification (also known as the ignition angle) is the angle by which firing is delayed
beyond the natural take over for the next thyristor. The transition could be delayed using grid control. Grid
control is obtained by superposing a positive pulse on a permanent negative bias to make the grid positive.
Once the thyristor fires, the grid loses control.
Assuming no commutation (2 thyristors on same side conducting simultaneously during transfer), the voltage
waveforms across the thyristors as shown in figure 11.5.
R1 Y3 B5 R1
Y6 B2 R4 Y6
Vd = 2 x x 2x
2
cos d
3 - 3 +
3 2 1
= E. . sin + + sin -
3 3 3
3 2
Vd= E cos = V do cos (11.2)
The commutation period between two thyristors on the same side of the bridge is the angle by which one
thyristor commutates to the next. During this period WKHYROWDJHDWWKHHOHFWURGHIROORZVPHDQYROWDJHRIWKH
2 conducting thyristors on the same side. This is shown in figure 11.6.
192 High Voltage Engineering - J R Lucas, 2001
R1 w Y3 B5 R1
With both the delay angle and commutation being present, the magnitude of the direct voltage may be
determined from equation (11.3) as follows.
+
E 3 3
Vd = 2 2
2
f ( ) d
3 - 3 +
- 3 + +
+
3 2E
(cos ( + ) + cos ) . d +
3
= 1 2
cos . d
3
2 3
- 3 + - 3 + +
V do [ cos + cos ( + )]
Vd = (11.3)
2
An alternate method of derivation of the result is based on comparison of similar areas on the waveform.
Figure 11.7 gives the necessary information.
. .
B2
A1 B1
A2
=0 + 2/3++ + ++
. .
B3 A3
In this integral, in graphical form, area A1 can be replaced by area B1. Similarly, area A2 can be replaced by
area B2 and area A3 by area B3. The integral equation then reduces to the form shown below.
-
3 2E
Vd=
2
sin d
+
=
3 2E
[ cos ( + ) - cos ( - ) ]
2
Vd=
3 2E
[ cos + cos ( + ) ]
2
= 0 [ cos + cos ( + )]
V
2
Commutation is a result of the a.c. system inductance Lc, which does not allow the current through a thyristor
to extinguish suddenly. Thus the larger the current the larger the commutation angle
If the extinction angle for rectifier operation w is defined as w = .WKHQ9d can be written as in equation
11.4.
Consider the commutation between thyristors 1 & 3 in the bridge circuit shown in figure 11.8. Let ic be the
commutation current. The commutation current is produced by the voltage ec which is the line voltage between
phases 1 and 2.
V d = 21 [ cos + cos w ] (11.4)
+
Ld Id
1 3 5
ic
Lc
E1 ec
Lc 4 6 2
E2
E 2
ec = E 2 - E 1 = cos ( t + ) - cos ( t - )
3 3 3
= 2 E sin t
This can also be written in the following form, with ic = 0 at the start of commutation and ic = Id at the end of
commutation.
194 High Voltage Engineering - J R Lucas, 2001
d ic
ec = 2 L c
dt
w
1
2 2 E sin t d ( t ) = Lc I d
E
i.e. ( cos - cos w ) = Lc I d
2
2 Lc
cos - cos w = Id (11.5)
E
2
cos + cos w = V d (11.6)
Vo
Equation 11.4 can also be written of the form of equation (11.6).
From equations (11.5) and (11.6) w may be eliminated to give the equation (11.7).
cos = V d + Lc I d
V0 2E
3 2E 3 Lc
V 0 = , cos = V d +
V0 V0
3 Lc
V d = V 0 cos - Id (11.7)
It can also be shown that equation (11.7) can be rewritten in terms of the extinction angle w instead of the
ignition angle .DVLQHTXDWLRQ
3 Lc
V d = V 0 cos w + Id (11.8)
Equation (11.7) suggests that the convertor may be represented by a no load d.c. output voltage Vo cos .
5 &/c,d
HFFFFFFFFI
HFFFFFFFFFFMLFFFFFFFFFFFFF
GJFFFFFFFFK
G G
GG
9RFRV.FFOFFG
FNFG9d
G G
GG
GG
JFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Figure 11.9 - Equivalent circuit for Rectifier
and a series fictitious resistance &/c/ as shown in figure 11.9. The fictitious resistor does not however
consume any active power.
High Voltage Direct Current Transmission 195
11.2.3 Current Waveforms
If Commutation is not considered, the current waveforms through each thyristor (assuming a very high value of
inductance Ld in the d.c. circuit to give complete smoothing) is a rectangular pulse lasting exactly one-third of a
cycle. This is shown in figure 11.10 for the cases without delay and with delay.
V1 _._ V1
I1
Id
. ZLWK.
Figure 11.10 - Thyristor current waveforms (
When commutation is considered, the rise and fall of the current waveforms would be modified as they would
no longer be instantaneous, as shown in figure 11.11.
V1 V1
I1 I1
Since each phase has 2 thyristors on the opposite half cycles, the a.c. current waveform on the secondary side
of the transformer has a non-sinusoidal waveform as shown in figure 11.12.
V1 V1
I1 I1
__|
If commutation angle is not considered, we can easily calculate the r.m.s. value of the a.c. current on the
transformer secondary Is as in equation (11.9).
196 High Voltage Engineering - J R Lucas, 2001
1 2
Is= . . I d2 = 2
I = 0.8165 I d
3 d (11.9)
3
Usually harmonic filters are provided on the a.c. system, so that only the fundamental component need to be
supplied/absorbed from the a.c. system. From Fourier analysis, it can be shown that the fundamental
component is given as follows, resulting in equation (11.10).
1 2 3
I = I max = . . I d cos t d ( t )
2 2 - 3
2 6
I= I d 2 sin = I d = 0.78 I d (11.10)
3
If filters were not provided, it can be shown, using the Fourier series analysis, that the r.m.s. ripple on the a.c.
system would be 0.242 Id (or 31 % of the fundamental)
Note: For normal operation neglecting the commutation angle, in the above calculations of the alternating
current, gives rise to an error only of the order of 1%.
As can be seen from the voltage and current waveforms on the a.c. side, the current lags the voltage due to the
presence of the delay angle .DQGWKHFRPPXWDWLRQDQJOH7KXVVLQFHRQO\DFWLYHSRZHULVWUDQVPLWWHGLQD
d.c. link, the convertor must consume the reactive power.
Since the convertor consumes reactive power, there will be a power factor associated with the convertor on the
a.c. side. This can be calculated as follows.
Since the convertor does not consume any active power, there must be power balance.
Vd Id = 3 E I cos 3
Thus if a high inductance is connected with the load, the limit of power transfer under rectification is . .
o
However, if no inductance were present with the load ( i.e. Ld=0) then the voltage and the current waveforms
would become identical in shape (since the load is purely resistive). Under these conditions, the voltage cannot
go negative at any instant of time, since the current cannot flow in the opposite direction through the thyristors.
The power transmitted would then become zero only at . . Figure 11.13 shows typical output current
o
Id Id
Ld = Ld = 0
In section 11.3.3 it was seen that the current waveform on the secondary side of the convertor transformer was
as shown in figure 11.14
Id
-
-
-Id
The same current waveform appears on the primary side of the convertor transformer (a.c. system) when the
winding connection is star-star, if no filters are present. If filters are present they would filter out some of the
harmonics and make the a.c system currents more or less sinusoidal.
When the convertor transformer is delta-star connected, the corresponding primary current waveforms would
be as shown in figure 11.15.
2Id/3
Id/3
-
-2Id/3
Each of the waveforms shown in figures 11.14 and 11.15 contain the same harmonics (6k1) with their
amplitudes inversely proportional to the harmonic number. The polarities of some of the components of the
two waveforms are opposite, so that when a star-star and delta-star convertor bridge are connected in cascade,
only the (12k1) harmonics remain. Thus less filtering is required. Further when commutation is present, the
harmonic amplitudes reduce due to smoothing action.
198 High Voltage Engineering - J R Lucas, 2001
Note: During normal operation of the convertor as a rectifier, the delay angle .LVVPDOODERXW ), while the
0
0
commutation angle is comparatively larger (about 20 ).
11.2.6 Inversion
Because the thyristors conduct only in one direction, the current in a convertor cannot be reversed. Power
reversal can only be obtained by the reversal of the direct voltage (average value) Vd.
For inversion to be possible, a high value of inductance must be present, and the delay angle .!0, since Vd
changes polarity at this angle. The theoretical maximum delay for inversion would occur at . 0.
Thus it is common practice to define a period of advance from this point rather than a delay from the previous
cross-over as defined for rectification. Thus we define -.DVWKHLJQLWLRQ angle for inversion or the angle
RIDGYDQFH6LPLODUO\WKHH[WLQFWLRQDQJOHLVDOVRGHILQHGDV/ - w. The definition of the commutation
DQJOHLVXQFKDQJHG7KXV /
It must be noted, that unlike with rectification which can be operated with . LQYHUVLRQFDQQRWEHFDUULHG
RXWZLWK VLQFHDPLQLPXPDQJOH/0 is required for deionisation of the arc and regaining grid control.
Thus we have the practical relationship /0 < 3UDFWLFDOYDOXHVRI/0 lie between 10 and 80.
R4 Y6 B2
B5 R1 Y3
Inversion cannot of course be carried out without a d.c. power source. Further, to obtain the necessary
frequency for the a.c. on inversion, the commutation voltage is obtained from either synchronous machines or
from the a.c. system fed. In isolated systems, L C circuits may also be sometimes used for the purpose. Figure
11.16 shows the thyristor voltage waveforms for inversion.
During inversion, each thyristor conducts during the negative half cycle, so that the direct voltage waveform
and the corresponding current has the form shown in figure 11.17.
Since the direct voltage is always negative during inversion, it is common practice to omit the negative sign
from the expression.
The power factor of the invertor can be shown to be given by the equation
The control characteristics of the convertor are the plots of the variation of the direct voltage against the direct
current. These are described in the following sections.
11.3.1 Natural Voltage Characteristic (NV) and the Constant Ignition Angle (CIA) control
Vd
N.V. Characteristic of Rectifier
Vo
9RFRV.
C.I.A. Control
Id
The Invertor is usually operated at constant extinction angle. This has the characteristic equation given by Vd
= V0 cos /-&/c/,d. This is shown in figure 11.19.
200 High Voltage Engineering - J R Lucas, 2001
0
Id
9RFRV/&($FRQWURO
Vd
In a d.c. link it is common practice to operate the link at constant current rather than at constant voltage. [Of
course, constant current means that current is held nearly constant and not exactly constant].
In constant current control, the power is varied by varying the voltage. There is an allowed range of current
settings within which the current varies.
The complete characteristic of each convertor has the N.V. characteristic and equipped with C.C. control and
the C.E.A. control. This is shown in figure 11.20 for a single convertor.
Vd
N.V. Characteristic of Rectifier
Vo
9RFRV.
C.C. control
Ids Id
Inversion
9RFRV/
9RFRV/R&($FRQWURO
Vd
Note: The constant current controller adjusts the firing angle .VRWKDWWKHFXUUHQWLVPDLQWDLQHGDWDVHWYDOXH
even for short-circuits on the d.c. line. The C.C. control is present in the invertor too, although the invertor is
not usually operated in that region. The rectifier is normally operated in the C.C. region while the invertor is
operated in the C.E.A. region.
High Voltage Direct Current Transmission 201
11.3.5 Compounding of Convertors
Figure 11.21 shows a system of 2 convertors, connected by a hvdc link. Both convertors are provided with
CEA and CC control so that either can work as a rectifier or an invertor. The compounded characteristics are
shown in figure 11.22.
convertor A convertor B
3-phase ac hvdc link
Id
Phase
C.E.A.
Advance Control for
Control
Circuit
E Convertor B
Id
C.C. Control for
Idm Control
Ids Convertor A
Figure 11.21 - Compounding of Convertors
The margin setting Idm between the current setting Ids for the invertor and for the rectifier is usually kept at
about 10% to 20% of the current setting. The setting of the convertor operating as rectifier is kept higher than
the setting of that as invertor by the margin setting Idm.
Vd
Vo N.V. Characteristic of A
A as Rectifier
B as Invertor changed C.C. control of A
C.C. control of A (A as rectifier)
for A as invertor
IdsIdm Ids+Idm
Ids
A as Invertor
B as Rectifier
Vd
Figure 11.22 - Compounded characteristic of Convertors
The usual operating point for power transfer is the intersection of the CC control of the rectifier and the CEA
control of the invertor. (For comparison, the characteristics of convertor B has been drawn inverted). It must
also be ensured by proper tap changing that the N.V. characteristic of the convertor operating in the
rectification mode is higher than the C.E.A. characteristic of the invertor, as Vo of the two ends are not
necessarily equal.
202 High Voltage Engineering - J R Lucas, 2001
With convertor A operating as rectifier, and convertor B operating as invertor, the steady state current under all
circumstances will remain within the upper limit (Ids + Idm) and the lower limit Ids. That is, the system direct
current will not change by more than Idm under all operating conditions. By reversing the margin setting Idm,
that is making the setting of convertor B to exceed that of A, power flow can be automatically reversed.
Convertor B will then operate as a rectifier and A as an invertor. The reversal of power occurs as a result of the
reversal of polarity of the voltage.
The convertor operating equations for voltage Vd and current Id are expressed as follows.
3 2 E ( cos + cos w )
Vd=
2
E
Id = ( cos - cos w )
2 Lc
Vd o
w =0
o w =15
o
1.0 w =30
o
w =45
o o
=150 w =60
o o
=135 w =75
o
0.5 =180
o o
=120 =165
o
w =90
o
=105
w =105
o Id
0 =90
o
0.5o =60
o 1.0
=30 w =120
o
o o
=15 =45
o
w =135 w =165o
o
-0.5 w =180
o
w =150 o
=75
o
=60
o
-1.0 =45
o
o =30
=0 o
=15
Figure 11.23 - Per unit convertor chart
It is useful to draw the convertor chart in per unit. For this purpose the natural selection for the base voltage is
the maximum direct voltage output Vdo. There is no such natural current base. Thus it is convenient to select
the constant appearing in equation (11.5) for current as the base quantity. Thus the selected base quantities are
as given in equation (11.15).
High Voltage Direct Current Transmission 203
3 2E E
V base = , I base = (11.15)
2 Lc
With these base quantities, the per unit voltage Vd and per unit current Id are given as follows.
which give the simple per unit characteristic equations (11.16) and (11.17).
In the chosen per unit system, constant delay angle control (or the natural voltage characteristic) correspond to
straight lines with slope (-) 0.5 on the per unit voltage-current chart. Similarly constant extinction angle control
correspond to straight lines with slope (+) 0.5.
Since voltages are measured in the opposite direction for inversion, these equations may be rewritten in their
more usual form as in equations (11.18) and (11.19).
From the characteristics, the constant commutation angle characteristic may be obtained by subtraction as
follows.
-/RU Z-.
D.C. links are classified into Monopolar links, Bipolar links, and Homopolar links.
In the case of the monopolar link there is only one conductor and the ground serves as the return path. The link
normally operates at negative polarity as there is less corona loss and radio interference is reduced. Figure
11.23 (a) shows a monopolar link.
The bipolar links have two conductors, one operating at positive polarity and the other operating at negative
polarity. The junction between the two convertors may be grounded at one or both ends. The ground does not
normally carry a current. However, if both ends are grounded, each link could be independently operated when
necessary. This is shown in figure 11.23 (b).
204 High Voltage Engineering - J R Lucas, 2001
As was mentioned earlier, the harmonics present on the a.c. system are (6k1). Thus the a.c. harmonic filters
are tuned to the 5th, 7th, 11th, and 13th harmonics to reduce the harmonic content in the voltages and currents
in the a.c. network to acceptable levels. Higher harmonics would not penetrate very far into the a.c. system.
The harmonics are mainly present in the a.c. current as the a.c. voltage is heavily dependant on the a.c. system
itself.
The Harmonics present on the d.c. side are mainly on output voltage. These are in multiples of 6 as the
waveform repeats itself 6 times. The d.c. current is smoothed by the smoothing reactors.