Advanced Diagnostics Ford Manual-Ford
Advanced Diagnostics Ford Manual-Ford
w w w . a d v a n c e d - d i a g n o s t i c s . c o m
™
COPYRIGHT 2013
CONTENTS
PAGE
APPLICATIONS 3
SPECIAL FUNCTIONS
PATS 1 & 2 (PETROL) 9 - 10
PATS 1 & 2 (DIESEL) 11 - 12
PATS GALAXY (DIESEL) 13 - 14
PATS 3 (SCP) 15 - 16
PATS 3 (SCP CODED) 17 - 18
PATS 3 (CAN CODED) 19
CODED 2007 TRANSIT 20 - 21
CODED 2007 FIESTA 22 - 23
CODED PROXIMITY 24 - 26
CODED NON-PROXIMITY 27 - 28
FALCON BEM 29
FALCON PCM 30
BA FALCON / SX TERRITORY 31
BF FALCON / SY TERRITORY 32 - 33
FG FALCON 34 - 36
FORD CODED 2014 37 - 43
VIN CHECKER 44
FORD Software
ADS100 Ford
FOCUS PUMA
FUSION/FIESTA SCORPIO
ESCORT/FIESTA 2
PIN
GENERAL OPERATION
There have been many variations on the original system fitted. This system has a separate PATS Amplifier, however
on subsequent systems the PATS module was incorporated into the Engine Management ECU.
SYSTEM OPERATION
The PATS system is a PASSIVE Anti-theft system which requires no special procedures for the driver to arm or disarm
the system. The system is operated by a transponder fitted within the ignition key’s body, which communicates with
the PATS module ignition transceiver mounted around the lock barrel.
The easy method of identifying a PATS vehicle is if the key has a small imprint showing where the transponder is
fitted. The code for the transponder is stored in memory within the PATS amplifier or the Engine Management ECU.
The PATS system reads the code when the ignition key is turned from position 0 to position 1. If the correct code is
received then the engine will start.
When vehicles are fitted with Diesel Smart Modules or EPIC, the PATS code is stored in these systems as well, and
requires clearing when new keys are programmed.
KEY OPERATION - UP TO 98 ¼ MY
Three keys are allocated to each vehicle, the first key which is inserted is known as the master and is usually identified
by it’s RED colour. The other keys that are used are known as slave keys and are usually BLACK with a RED insert. Up
to 16 keys can be programmed into the PATS system.
The newer systems are only supplied with 2 keys. Both keys are required to program further slave keys. Up to a
maximum of 8 keys can be programmed to this PATS system.
The LED indicator is used for the PATS system and also other Anti-theft systems fitted to the Ford vehicle range. When
the ignition is switched ON, the PATS LED will illuminate for 3 seconds while it performs a self-test, after which it
extuingishes. When the PATS system is armed and immobilised the vehicle, the PATS LED will flash quickly.
If there is a fault on the PATS system, and the engine can start, the PATS LED will illuminate for 60 seconds
continuously, and then flash the PATS fault code 10 times. If the engine is unable to start and disabled by the PATS
system, then the PATS LED will FLASH for 60 seconds and then flash the PATS fault code 10 times. PATS LED is
mounted either in the front headlining or next to the heater controls/clock.
The PATS system fitted to the Probe is unlike the other systems. The main difference is the system cannot be
diagnosed with the FDS2000 or the AD PROGRAMMING SYSTEM. Additional keys and re-programming of new keys are
performed in a different procedure as well.
GENERAL OPERATION
The system replaces the TIMED ACCESS, which was first used in 1994.
The new system replaces the TIMED ACCESS countdown timer with a security algorithm which will display an outcode
when you try to program keys. This outcode needs converting and an incode is required.
Advanced Diagnostics have developed a system which uses this incode and outcode system, however the way the system
works means that it is not 100% accurate and some vehicles cannot be programmed until the codes have been checked.
The system uses an internet system as described on the following pages, and requires web access when you are at the
vehicle, Advanced Diagnostics forum access and a valid AD100, MVP, TCODE, Codeseeker or DM100 serial number and
passcode to use the system.
NEW FIESTA
The new fiesta can be a difficult vehicle to program, as there are 2 systems TYPE 1 and TYPE 2.
The problem is that it is difficult to know which is the correct one, and therefore because you can communicate with both,
it means if you do not identify the correct system, then you have to try both types with the coded procedures.
TYPE 1
TYPE 2
When you try to ADD or CLEAR the system, the MAIN RELAY will click and the FUEL PUMP will run for a brief second, this
indicates it is a TYPE 2 system.
Also TYPE 2 systems tend to have CHROME BEZEL/EDGING on the instrument cluster.
Ford have updated their coded system from 2007 for Transit, Mondeo, S Max and later Fiesta.
The system operates on the same principle as the earlier coded vehicles i.e. it requires an Incode and Outcode via our
website.
1. The remote part of the key is programmed when the keys are programmed.
2. Once the keys have been erased, the new keys need to be programmed individually using the ADD KEY function.
IMPORTANT: These keys are not cycled in at the end, please follow the on screen instructions.
GENERAL OPERATION
FORD SYSTEMS
IGNITION ON
MIN CLEAR
TIMED CODED BEFORE
SYSTEM NO. OF TIME
ACCESS ACCESS CONNECTING
KEYS (Minutes)
TESTER (*)
PATS 1 3 8:00
PATS 2 3 8:00
NON PROX 2 -
BA FALCON 2 10:00
BF FALCON 2 -
(*) TURN IGNITION ON AND LET IMMOBILISER LED STOP FLASHING. THEN CONNECT TESTER
SPECIAL FUNCTIONS
+ GM / OPEL
+ HONDA / ACURA
+ HYUNDAI
+ INFINITI
+ AUS
+ EURO SWITCH IGNITION ON KEYS PROGRAMMED: 2
+ S. AMERICA
ECU IDENTIFICATION
+ BY VEHICLE
SWITCH IGN. ACCESSORY
+ BY SYSTEM ECU IDENTIFICATION
FAULT CODES IGNITION STATUS: ON
+ ESCAPE ******
+ ESCORT/ORION BACK TO ABORT
+ EXPOLRER
+ FAIRLANE
+ PETROL
KEYS PROGRAMMED: 0
SPECIAL FUNCTIONS
PROGRAM KEYS
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
SPECIAL FUNCTIONS
+ GM / OPEL
+ HONDA / ACURA
+ HYUNDAI
+ INFINITI
+ AUS
+ EURO SWITCH IGNITION ON CLEAR TIME: 8.00
+ USA
+ S. AMERICA
ECU IDENTIFICATION
THE TESTER WILL NOW CLEAR THE
THE FOLLOWING PROCEDURE SYSTEM WHICH WILL TAKE APPROX
SHOWS ‘BY VEHICLE’ SELECTION. 8 MINUTES.
IF ‘BY SYSTEM’ IS CHOSEN THEN THE FOLLOWED BY APPROX 15 MINS TO
PATS 2 DIESEL
SYSTEM TYPE WHERE KNOWN IS CLEAR THE DSM MODULE.
SHOWN IN THE APPLICATION PAGES
+ BY VEHICLE
TIME REQUIRED 8:00
+ BY SYSTEM ECU IDENTIFICATION
FAULT CODES
******
> SPECIAL FUNCTIONS BACK TO ABORT
+ ESCAPE ******
+ ESCORT/ORION BACK TO ABORT
+ EXPOLRER
+ FAIRLANE
VEHICLE SELECTION
+ PETROL
+ DIESEL KEYS PROGRAMED 2 SWITCH IGNITION OFF
SPECIAL FUNCTIONS
KEYS PROGRAMMED: 0
PROGRAM KEYS
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
SPECIAL FUNCTIONS
+ USA ******
WAITING TO CLEAR
+ S. AMERICA
BACK TO ABORT
ECU IDENTIFICATION
7 MO953257AB V41 V
THE FOLLOWING PROCEDURE
SHOWS ‘BY VEHICLE’ SELECTION. V BC 2 3 PLEASE ENTER THE TOTAL NUMBER
IF ‘BY SYSTEM’ IS CHOSEN THEN THE OF KEYS YOU REQUIRE TO
K
SYSTEM TYPE WHERE KNOWN IS PROGRAM
SHOWN IN THE APPLICATION PAGES
SPECIAL FUNCTIONS
PLEASE PROGRAM
ADDITIONAL KEYS
SPECIAL FUNCTIONS
PATS 3 (SCP)
KEY PROGRAMMING
07 >
VEHICLE SELECTION
+ FORD MIN KEYS REQUIRED: 2
VEHICLE SELECTION DIAGNOSTIC MENU The tester will now start to clear the
PATS system from memory.
+ MONDEO ECU IDENTIFICATION
+ TRANSIT CONNECT
VEHICLE SELECTION
+ MANUAL After clearing, cycle the key in the
ignition from ON to OFF and then back
+ AUTOMATIC KEYS PROGRAMED 2 to ON. Then remove.
Repeat for second key.
SPECIAL FUNCTIONS
PATS 3 (SCP)
KEY PROGRAMMING ADD KEY
DIAGNOSTIC MENU
Check the anti-theft warning light for
each key. It should turn on for 2 ECU IDENTIFICATION
seconds and then go off with each key.
FAULT CODES
.
Rapid flashing means either the key is
ACTUATORS
faulty or un-programmed.
> SPECIAL FUNCTIONS
NOTES :
1. If an error is made, leave the ign on
for 20 sec & insert both keys and turn
ign ON. Then try starting again. PRESS ENTER KEY
2. If the diagnostic session is called
before other systems are allowed to
settle, the counter will show 0.00 and DIAGNOSTIC MENU
access denied or coded
CLEAR / ERASE PATS
access.
KEYS PROGRAMMED
ADD KEY
NOTES:
1. This function is not available on
every vehicle e.g. Fleet vehicles
SPECIAL FUNCTIONS
+ HYUNDAI
+ INFINITI PRESS ENTER KEY PRESS ENTER KEY
+ TRANSIT CONNECT
+ TRANSIT
+ PETROL
+ DIESEL KEYS PROGRAMED 2
97 / 98 KEYS PROGRAMMED
07 >
SPECIAL FUNCTIONS
DIAGNOSTIC MENU
CLEAR / ERASE PATS
KEYS PROGRAMMED
ADD KEY
CODED ACCESS
KEYS PROGRAMMED: 2
ACCESS GRANTED
ADD KEY
READING KEY
KEYS PROGRAMMED: 2
BACK’ TO EXIT
ENTER’ TO PROGRAM
NEXT KEY
SPECIAL FUNCTIONS
+ GM (USA)
+ GM / OPEL 05 FOCUS PATS 3 CAN ACCESS GRANTED
+ HONDA / ACURA (P.C.M)
+ HYUNDAI
+ INFINITI PRESS ENTER KEY
+ GRANADA / SCORPIO
+ KA
+ LTD
VEHICLE SELECTION
+ PETROL
SPECIAL FUNCTIONS
REMOTE IS PROGRAMMED AT
THE SAME TIME AS THE KEY. SWITCH IGNITION ON PROCEDURE COMPLETE
+ S. AMERICA
+ TRANSIT CONNECT
+ TRANSIT
SPECIAL FUNCTIONS
ADD KEY
ADD KEY
KEYS PROGRAMMED: 2
BACK’ TO EXIT
ENTER’ TO PROGRAM
NEXT KEY
ADD KEY
PROCEDURE COMPLETE
FINISHED
SPECIAL FUNCTIONS
+ FORD
+ GM (USA) PATS 3 CAN KEYS PROGRAMED 2
SPECIAL FUNCTIONS
IGNIITION ON
ADDITIONAL KEYS
IGNITION ON
ADDITIONAL KEYS
SUCCESS
SPECIAL FUNCTIONS
CODED PROXIMITY
KEY PROGRAMMING
VEHICLE SELECTION KEYS PROGRAMMED
+ NON PROXIMITY
REMOTE IS PROGRAMMED AT THE
SAME TIME AS THE + PROXIMITY KEYS PROGRAMED: 2
PROXIMITY FOB.
PROG KEYS IN CABIN: 0
MIN 2 KEYS MUST BE
PROGRAMMED
SPECIAL FUNCTIONS
CODED PROXIMITY
KEY PROGRAMMING
PROGRAM PROX FOB PROGRAM PROX FOB
PRESS UNLOCK
REMOVE BLANKING INSERT FROM
SUCCESS KEY SLOT ON THE STEERING FOR 15 SEC
COLUMN.
PROX FOB 2
PLACE PROX FOB 1 IN
2 KEYS REQUIRED
SUCCESS
EMERGENCY KEY SLOT
PROGRAM TRANSPONDER
PROGRAM TRANSPONDER
PROGRAM PROX FOB
PROGRAM TRANSPONDER
PROGRAM TRANSPONDER
TRANSPONDER 2
THE PROX FOB MUST BE INSIDE REMOVE PROX FOB FROM
THE VEHICLE CABIN WHILST BEING EMERGENCY KEY SLOT SUCCESS
PRESSED.
SPECIAL FUNCTIONS
CODED PROXIMITY
KEY PROGRAMMING
PROGRAM TRANSPONDER
PROGRAM KEYS
2 KEYS PROGRAMMED
DO YOU WANT TO PROG
ADDITIONAL KEYS
IF ANOTHER KEY REQUIRES
PROGRAMMING THE PROCESS
WILL BE REPEATED.
FINISHED
SPECIAL FUNCTIONS
+ FORD
+ GM (USA) SWITCH IGNITION ON PROCEDURE COMPLETE
+ GM / OPEL
+ HONDA / ACURA
+ HYUNDAI
+ INFINITI PRESS ENTER KEY PRESS ENTER KEY
VEHICLE SELECTION
ECU IDENTIFICATION IMPORTANT
+ AUS
+ EURO ONCE THE CORRECT CODE HAS
PATS NON-PROX CAN BEEN ACCEPTED DO NOT
+ USA DISCONNECT TESTER.
PRESS ENTER AND SELECT ADD
+ S. AMERICA KEY FUNCTION TO NOW PROGRAM
A KEY
VEHICLE SELECTION
DIAGNOSTIC MENU ADD KEY
+ PETROL
CLEAR / ERASE PATS KEYS PROGRAMMED: 1
+ DIESEL
ADD KEY BACK’ TO EXIT
VEHICLE SELECTION
REMOVE KEY FROM IGNITION AND
96 > 97 INSERT NEXT KEY TO BE
PROGRAMMED.
97 > 98
KEYS PROGRAMED 2
98 > 07
+07 >
SPECIAL FUNCTIONS
ADD KEY
ADD KEY
KEYS PROGRAMMED: 2
BACK’ TO EXIT
ENTER’ TO PROGRAM
NEXT KEY
ADD KEY
PROCEDURE COMPLETE
FINISHED
SPECIAL FUNCTIONS
FALCON - BEM
KEY PROGRAMMING
+ HONDA / ACURA
+ HYUNDAI
+ INFINITI PRESS ENTER KEY
+ USA
+ S. AMERICA
VEHICLE SELECTION
+ AU FALCON
+ BA FALCON SWITCH IGNITION OFF
+ BF FALCON
+ PCM
BACK TO ABORT
BACK TO ABORT
SPECIAL FUNCTIONS
FALCON - PCM
KEY PROGRAMMING
+ USA
+ S. AMERICA
+ BF FALCON
******
BACK TO ABORT
ACCESS GRANTED
SWITCH IGNITION ON
BACK TO ABORT
PROCEDURE COMPLETE
FALCON PCM PATS
SPECIAL FUNCTIONS
BA FALCON / SX TERRITORY
KEY PROGRAMMING
DIAGNOSTIC MENU
+ HYUNDAI
+ INFINITI PRESS ENTER KEY PRESS ENTER KEY
+ USA
+ S. AMERICA
TIMED ACCESS
VEHICLE SELECTION
GAINING ACCESS
+ AU FALCON
TIME REQUIRED 10:00
+ BA FALCON SWITCH IGNITION OFF
+ BF FALCON ******
ACCESS STATUS
IN PROGRESS
BACK TO ABORT
SPECIAL FUNCTIONS
BF FALCON / SY TERRITORY
KEY PROGRAMMING
DIAGNOSTIC MENU
ECU IDENTIFICATION
TURN IGNITION ON AND LEAVE FOR
30 SECONDS BEFORE CONNECTING > SPECIAL FUNCTIONS
THE TESTER.
+ GM / OPEL
+ HONDA / ACURA
+ HYUNDAI
+ INFINITI PRESS ENTER KEY
+ EURO
CONTINUE
+ USA
+ S. AMERICA
ECU IDENTIFICATION
SPECIAL FUNCTIONS
BF FALCON / SY TERRITORY
KEY PROGRAMMING PARAMETER RESET
TO COMPLETE THE
When ENTER pressed PROGRAMMING PROCEDURE
SWITCH IGNITION OFF
door locks will lock PLEASE DISCONNECT THE
TESTER AND RE-START.
THEN SELECT PARAMETER
RESET
DISCONNECT TESTER
AND PERFORM SWITCH IGNITION ON
PARAMETER RESET
SPECIAL FUNCTIONS
FG FALCON
KEY PROGRAMMING KEY PROGRAMMING KEY PROGRAMMING
TIME : 09
PRESS ENTER KEY PRESS ENTER KEY
+ FAIRLANE
+ AU FALCON SWITCH IGNITION ON
+ BF FALCON
+ FG FALCON TIME : 07
2 KEYS REQUIRED
CONTINUE
SPECIAL FUNCTIONS
FG FALCON
KEY PROGRAMMING KEY PROGRAMMING KEY PROGRAMMING
DISCONNECT TESTER
RECONNECT AND INCODE OUTCODE SWITCH IGNITION ON
PERFORM PARAMETER
RESET ON ICM
+ BEM
+ ICM ACCESS GRANTED FG FALCON
+ PCM
VIN : 6FPAAAJGSWA123456
PCM
SPECIAL FUNCTIONS
FG FALCON
KEY PROGRAMMING KEY PROGRAMMING
*******
******* *******
*******
SWITCH IGNITION ON
SPECIAL FUNCTIONS
KEYS PROGRAMMED
CLEAR KEYS
WARNING
LEAVE IGNITION OFF
ALL KEYS WILL BE CLEARED
CONTINUE?
SPECIAL FUNCTIONS
CODED ACCESS
SUCCESS
ONLINE DATA REQUEST
REQUIRED TO COMPLETE
FORD CODED
PLEASE WAIT GENERATING
REQUEST.
PROCEDURE
STEP 1
SPECIAL FUNCTIONS
CLEAR KEYS
NOW TYPE IN THE FINAL SUCCESS
DATA CODE DISPLAYED ON
CYCLE KEYS TO PROGRAM
YOUR SMART PHONE INTO
THE TESTER KEYS PROGRAMMED :2
FORD CODED
__ __ __
CHECK REMOTES WORK AND
THE KEY STARTS THE
VEHICLE
1 2 3 4 5
6 7 8 9 0
FORD CODED
63 AA 4D
CODED ACCESS
SUCCESS
CLEAR KEYS
SUCCESS
CYCLE KEYS TO PROGRAM
KEYS PROGRAMMED :0
SPECIAL FUNCTIONS
VEHICLE SELECTION
ECU IDENTIFICATION FORD CODED
+ B MAX
PLEASE WAIT GENERATIING
+ C MAX
FORD PROX REQUEST
+ COUGAR
USE THE QR CODE MOBILE APP TO
+ GALAXY
GET RESPONSE
+ FUSION
PRESS F3 TO MANUALLY ENTER
+ FOCUS
PRESS ENTER KEY CODE USING WEBSITE
SPECIAL FUNCTIONS
FORD CODED
PLEASE WAIT GENERATING
REQUEST.
USE THE QR CODE MOBILE APP
TO GET RESPONSE.
PRESS F3 TO MANUALLY ENTER
CODE USING WEB SITE
PRESS ENTER KEY
123.. >
FORD CODED SCAN THE QR CODE
IF YOU HAVE A FORD DEALER
__ __ __ DISPLAYED ON THE TESTER
LOGIN - ENTER IT HERE TO
WITH YOUR SMARTPHONE
GAIN INSTANT ACCESS.
OR
SELECT 123… TO GET FULL
IF NOT SELECT NONE TO
CODE TO INPUT INTO THE
CONTINUE. 1 2 3 4 5 AD WEBSITE
F4 2E E2
CODED ACCESS
FORD CODED
SEC WAIT __ __ __
THIS MAY TAKE UP TO 5 HOURS
SPECIAL FUNCTIONS
+ GM / OPEL
+ HONDA / ACURA
+ HYUNDAI
PRESS ENTER KEY + INFINITI PRESS ENTER KEY
+ S. AMERICA
VEHICLE SELECTION
REPEAT THE PROCEDURE 98 > 04
FOR THE SECOND PROX KEY
05 > 11
2011 >
SPECIAL FUNCTIONS
123.. >
KEYS PROGRAMMED CLEAR TRANSPONDERS
PROGRAM TRANSPONDERS
CLEAR KEYS
SUCCESS
WARNING
ALL KEYS WILL BE CLEARED
CONTINUE?
VIN CHECKER
The Ford VIN checker is used to determine the production date of the vehicle.
+ FORD
+ GM (USA) JUL 98
+ GM / OPEL
+ HONDA / ACURA
+ HYUNDAI
+ INFINITI PRESS ENTER KEY
+ USA
+ S. AMERICA
YES = ENTER NO = BACK
VEHICLE SELECTION
S– MAX
TRANSIT CONNECT
TRANSIT
WINDSTAR
+ FORD BY SYSTEM
+ FORD VIN CHECK
SWITCH IGNITION ON
FORD CALCULATOR
ENTER LAST 7 DIGITS
OF VIN NUMBER
_______
1 2 3 4 5
6 7 8 9 0
FORD CALCULATOR
WM60543
44 Version 3.2 JULY 2014 Copyright 2014
COPYRIGHT 2013
GENERAL
If communication is made with the vehicle, and then no communication is experienced later or the communication is
random, check battery voltage and ensure it is at least 12.2 volts., particularly important on SCP , and all Transits
A new function has been introduced on the WDS which enables the dealer to disable the additional key function. This is
mainly used on fleet vehicles and hire companies to stop unauthorized key’s being added. If a system will not accept
additional keys, it may be because this has been enabled.
Fleet mode (unable to add a key) is disabled by clearing the PATS and DSM (diesel only) and reprogramming all keys.
When programming SCP systems, turn IGN ON before connecting TESTER or ADC110B to Diagnostic socket, then wait
for dashboard lights to settle, connect TESTER - otherwise a timed access system may display “access denied”.
Intermittent start with fault code 12- replace faulty aerial pick up.
If an incorrect key is used to try and start the engine, the correct key must be inserted and left in the IGN position for
at least 20 seconds, then switched OFF then back ON before the vehicle starts.
Fault Code 0 is an ECU trouble code, if this is set and cannot be cleared, then there is a problem with the ECU.
Normally the only way to fix this is to return the ECU for testing or replace it.
Fault Code 1000 is an ECU trouble code. This code can be set automatically if the vehicle has not been driven. The
code refers to the OBD drive cycle. In some instances it is not possible to program new keys if this code is set. Please
follow the following instructions if the code cannot be cleared or the keys cannot be programmed.
The OBD drive cycle code P1000 is the monitor code which monitors a number of the OBD parameters. This code can
be cleared by driving the vehicle or running the engine for around 5 minutes at a steady RPM and acceleration cycles.
The smoother the driving condition the quicker the code will be cleared.
If no keys are available, then the ECU can be disconnected for 30-45 minutes, which will also reset the system.
SELF DIAGNOSIS
The PATS system has it’s own self diagnosis test procedure which flashes codes. The PATS LED will flash quickly for 1
minute, and then start flashing the fault code as follows:-
A B C D
Code 11 Transceiver not connected
Code 12 Transceiver
Code 13 No key data received
Code 14 Part of the transponder code received
Code 15 Wrong transponder key
Code 21 Less than the minimum keys required programmed
Code 22 Failed diesel pump control unit identification
Code 23 The response code between pump control unit & powertrain
Code 31 DSM Communication
Code 32 DSM Communication
Code 34 DSM Communication
NOTE : If there are no fault codes, DO NOT clear fault codes as this can cause fault 1000 to be enabled.
Ford Escort, no communication with TESTER, switched Ignition OFF and ON very quickly, and communication gained.
Conclusion was bad connection on ignition switch.
DO NOT insert a blue chip transponder key into a red key system.
A new master key can only be programmed using the FDS2000 or the AD PROGRAMMING systems. Further slaves can
be added without any specialist equipment as follows :-
1. Insert master key, and turn to Position 2. PATS LED should illuminate.
2. Switch ignition from position 2 to position 0, and remove key. PATS LED will illuminate for 2 seconds. PATS
system is now in programming mode for 10 seconds.
3. Insert the new slave key, and turn from Position 0 to Position 2. PATS LED will flash once if successful.
4. Repeat for all new slave keys.
GALAXY
MANUAL PROGRAMMING PROCEDURES DO NOT WORK ON ANY FORD GALAXY VEHICLES.
PROBE
PROGRAMMING NEW/ADDITIONAL KEYS (2 or more keys available)
1. Using one of the existing keys (This becomes KEY 1), insert into ignition switch.
NOTE : When requested to turn the key ON or OFF, the time should not be less than 1 Second or more than 2
Seconds between operations. Unless stated otherwise.
2. Turn the Key to IGNITION ON and then OFF five times, stopping at the OFF position.
NOTE : PATS LED Should remain ON with the key in the OFF position.
3. Turn the IGNITION ON using KEY 1., within 15 seconds of step 2.
4. Turn the IGNITION OFF and remove KEY 1.
5. Insert KEY 2 within 60 seconds of PATS LED illuminating.
6. Turn ign ON and start engine with KEY 2. PATS LED will extinguish after 1-2 sec and engine remain running if
key is accepted.
7. Turn IGNITION OFF and remove KEY 2.
8. Insert KEY 3 within 15 seconds of removing KEY 2.
9. Turn IGNITION ON and start engine with KEY 3. PATS LED will extinguish after 1-2 seconds and engine remain
running if key is accepted.
10. Turn IGNITION OFF and remove KEY 3. Repeat as necessary for additional keys.
Programming new key(s) when no keys are available can only be completed by a FORD dealer.
1. On some vehicles a function is available to add a key without deleting the old keys. This takes the normal 10
minutes security access time.
2. If the procedure is not followed then a further security access time of 10 minutes will be required.
3. Some vehicles, especially fleets and hire companies have this feature disabled, and the normal clear down
procedure will be required.
iD 33 Transponder
iD 42 Transponder
iD 44 Transponder
iD 63 Transponder
NOTE: To make a copy of the key or replace the immobilizer system component parts (the key(s), steering lock, im-
mobilizer unit, and/or PCM), the customer should bring all keys to the dealer. This is because the previously pro-
grammed key IDs are erased when reprogramming the key IDs into the immobilizer unit and PCM.
NOTE: If the customer has only one valid key when replacing the immobilizer system component parts, the dealer
should contact a distributor to obtain the code word.
NOTE: To replace the immobilizer unit or PCM, there should be at least one valid key. Otherwise, both the immobilizer
unit and PCM should be replaced.
NOTE: The immobilizer unit and PCM cannot be changed from one car to another. If an immobilizer unit or PCM is re-
placed with one from another car, the engine will not start. Reprogramming of the IDs and code word of an immobi-
lizer unit that has already been programmed is not possible.
NOTE: The immobilizer unit and PCM should not be newly replaced as a trial during troubleshooting. If this is done, the
ID and code word will be programmed into the new unit and it cannot be used for other cars even if you find that the
old unit was normal.
NOTE: Confirm that all keys registered can start the engine after the reprogram procedure. When confirming, wait for
more than 5 seconds before inserting the next key.
NOTE: When the customer does not need to register more than two keys, the following procedures can be stopped
after registering two keys.
NOTE: If the key cannot be registered in spite of the fact that the immobilizer system operates normally, there may be
a malfunction with the key reminder switch or wiring harness.
NOTE: If no specific time interval is given, each step should be performed within 30 seconds of the previous step.
Key Replacement or Addition when the customer has two or more valid keys
1. NOTE: Key Replacement or Addition When the customer has two or more valid keys
2. Cut new transponder-equipped key(s).
3. Insert key 1 into the steering lock and hold for 1 second or more.
4. Remove and insert key 1 five times at no more than 1-second intervals.
5. After the final key insertion, verify that the security light flashes.
6. Remove the key from the steering lock and verify that the security light goes off.
7. Insert key 2 into the steering lock and turn the key to the ON position.
8. Verify that the security light illuminates for 1—2 seconds.
9. After verifying that the security light goes off, turn the key to the LOCK position and remove from the steering
lock.
10. Insert key 3 into the steering lock and turn the key to the ON position.
11. Verify that the security light illuminates for 1—2 seconds.
12. After verifying that the security light goes off, turn the key to the LOCK position.
13. If there are 4—8 keys (valid and/or new keys), repeat Step 5 with each key.
14. Wait for 30 seconds.
15. After reprogramming, clear DTCs stored in the PCM.
1. NOTE: If no specific time interval is given, each step should be performed within 30 seconds of the previous
step.
2. Remove and insert key 1 five times at no more than 1-second intervals.
3. After the final key insertion, verify that the security light flashes. (300 ms ON—300 ms OFF)
4. Wait for 5 minutes until the security light flashes at 1.2-second intervals.
5. Input the code word. For additional information, refer to Code Word Input Procedure in this procedure.
6. After verifying that the security light has switched from flashing to straight illumination, turn the key to the ON
position.
7. After verifying that the security light goes off, turn the key to the LOCK position and remove from the steering
lock.
8. Insert key 2 into the steering lock and turn the key to the ON position.
9. Verify that the security light illuminates for 1—2 seconds.
10. After verifying that the security light goes off, turn the key to the LOCK position and remove from the steering
lock.
11. Insert key 3 into the steering lock and turn the key to the ON position.
12. Verify that the security light illuminates for 1—2 seconds.
13. After verifying that the security light goes off, turn the key to the LOCK position.
14. If there are 4—8 keys (valid and/or new keys), repeat Step 5 with each key.
15. Wait for 30 seconds.
16. After reprogramming, clear DTCs stored in the PCM.
PRECAUTIONS
IN PARTICULAR : For vehicles fitted with STOP/START technology, the battery leads
must not be shorted together when the battery is disconnected as this can lead to damage to the car and
potential personal injury.
REMOTE PROGRAMMING
Transit (2000.5MY)
Procedure
1. Close all the doors.
2. Turn Ignition key from position 0 to II eight times within 10 seconds.
3. Make sure the vehicle locks and unlocks the doors.
4. Press the remote transmitter button within 20 seconds., and make sure the vehicle locks and unlocks all the doors.
5. Up to 20 seconds is allowed to programme the next remote transmitter.
6. To programme additional remote transmitters, repeat steps 4 and 5.
7. Turn the ignition key to position 0 to exit the programming mode.
Note : If programming ends with no new remote transmitters, the originals are retained.
Note : The anti-theft alarm and double locking module will exit programming mode automatically if four new remote
transmitters have been programmed or if no new remote transmitters programmed within the 20 second
programming mode.
REMOTE PROGRAMMING
NOTE : The first Cougars were 3 seconds instead of 6, and 20 seconds instead of 10.
REMOTE PROGRAMMING
Additional Information
A maximum of four keyless entry remote transmitters can be programmed to the central security module (CSM). Pro-
gramming must be done at the same time for all the
transmitters.
Note: To enter programming mode, make sure that the vehicle battery is fully charged and the anti-theft system is not
armed or triggered (if equipped).
1. Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during programming.
2. Turn the ignition switch from position I to position II at least four times in six seconds.
3. Turn the ignition switch to position I.
4. The CSM is now in the learning mode.
5. Press and hold one of the buttons on the remote transmitter until a chime sounds. This indicates a new
transmitter code has successfully received.
6. After each successful programming is completed, another 10 second learning mode is automatically entered, up
to a maximum of four times.
7. To program additional transmitters, repeat from step 5.
8. The system will leave the learning mode after the ignition switch is turned to position III, or if no new
transmitter is programmed during the 10 seconds, or if four remote transmitters have been programmed.
Note: An incorrect programming procedure does not effect the stored codes.
9. After successful programming, only the new programmed transmitters will be accepted.
10. Test all the programmed transmitters, by activating and deactivating the locking/unlocking functions.
1. The unlocking mode can be changed by pressing the locking and unlocking buttons on the remote transmitter
simultaneously for a minimum of four seconds.
2. The change is indicated by the turn signal lamps flashing twice.
3. The mode can be carried out as often as required by repeating step 11.
1. The unlocking mode can be changed by pressing the locking and unlocking buttons on the remote transmitter
simultaneously for a minimum of four seconds.
2. The change is indicated by the turn signal lamps flashing twice.
3. The mode can be carried out as often as required by repeating step 14.
Programming transmitters.
1. Insert the ignition key and turn it from position II to position 0 and back four times within three seconds.
2. Remove the ignition key. The module remains in learning mode for 20 seconds and the anti-theft warning
system light stays on continuously.
3. Press one of the transmitter buttons. The signal is learned by the module and indicated by a flashing anti-theft
warning system light. If necessary, repeat the procedure for other transmitters after two seconds.
4. Wait until the module programming is complete, or switch the ignition to ON.
Notes:
A maximum of four keyless entry remote transmitters can be programmed to the central security
module.
Programming must be done at the same time for all the transmitters.
To enter programming mode, make sure that the vehicle battery is fully charged and the anti-
theft
system is not armed or triggered (if equipped).
Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during
programming.
5. Turn the ignition switch from the OFF position to the ON position four times within three seconds to enter the
learning mode. Turn the ignition switch from the OFF position. The central security module will remain in the
learning mode for 20 seconds indicated by the LED in the instrument panel being illuminated continuously.
6. Press any button on the remote transmitter being programmed. When the signal from the remote transmitter is
accepted by the central security module, the LED will flash.
7. To program additional transmitters, repeat from step 6, with a two second delay after the LED flashes.
8. To exit the learning mode, turn the ignition switch to the ON position. If no transmitter signal is received by the
central security module for 20 seconds, the system will automatically exit the learning mode.
9. Test all the programmed transmitters, by activating and deactivating the locking functions.
REMOTE PROGRAMMING
An example key is pictured below, the remote part of the key is BLUE in colour to distinguish it is the new system.
w w w . a d v a n c e d - d i a g n o s t i c s . c o m
™