Professional Documents
Culture Documents
PowerCut 1600
PowerCut 1600
INTRODUCTION
SPECIFICATIONS
MAIN SCHEMATIC
WIRING DIAGRAMS
REPLACEMENT PARTS
REMOVAL/
REPLACEMENT
PROCEEDURES
MECHANIZED
CONVERSION
GENERAL
PART NO DESCRIPTION
0558007230 PC1600 230/460V Console
0558007230F PC1600 230/460V BL Console
Service Manual
This manual provides service / troubleshooting 0558007237 PC1600 575V BL Console
instructions for PC1600 consoles beginning with 0558007636 PC1600 400V Console
Serial Number .........PCJ912015 0558007234 PC1600 400V CE Console
0558007883 PC1600 MECH 230/460V
0558007884 PC1600 MECH 400V CE
0558008323 PC1600 460V Console
Manual # 0558008016- Rev. 1 3/2009 (BL = Bilingual)
This Service Manual is for experienced technicians. If you are not fully familiar with
the principles of operation and safe practices for arc welding and cutting equipment,
we urge you to read our booklet, “Precautions and Safe Practices for Arc Welding,
Cutting, and Gouging,” Form 52-529. Do NOT permit untrained persons to install,
operate, or maintain this equipment. Do NOT attempt to install or operate this equip-
ment until you have read and fully understand these instructions. If you do not fully
understand these instructions, contact your supplier for further information. Be
sure to read the Safety Precautions before installing or operating this equipment.
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and ac-
companying labels and/or inserts when installed, operated, maintained and repaired in accordance with
the instructions provided. This equipment must be checked periodically. Malfunctioning or poorly main-
tained equipment should not be used. Parts that are broken, missing, worn, distorted or contaminated
should be replaced immediately. Should such repair or replacement become necessary, the manu-
facturer recommends that a telephone or written request for service advice be made to the Authorized
Distributor from whom it was purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manu-
facturer. The user of this equipment shall have the sole responsibility for any malfunction which results
from improper use, faulty maintenance, damage, improper repair or alteration by anyone other than the
manufacturer or a service facility designated by the manufacturer.
2
SECTIONS
Safety 1
Introduction 2
Specifications 3
Description of Operation 4
Schematic Section Map 4.0
main power switch S1 4.1
control transformer T2 4.2
input bridge BR1 4.3
CONTACTOR K1 4.4
VOLTAGE SELECTOR SWITCH SW2 4.5
main transformer T1 4.6
output DIODES 4.7
Plasma control / DISPLAY board pcb1 4.8
FILTERS L1-L2 4.9
POWER BOARD PCB2 4.10
POWER DRIVER PCB3 - PCB4 4.11
THERMAL SWITCH TS1 4.12
PILOT ARC CIRCUIT 4.13
HELP CODES 4.14
PRESSURE TRANSDUCER PT1 4.15
EMC FILTER (CE Units) PCB7 4.16
SOLENOID SOL1 4.17
REMOTE PCB6 4.18
torch pt38 4.19
Wiring Diagrams 5
Replacement Parts 6
MECHANIZED CONVERSION 7
errors 8
General Information 10
3
table of contents
2.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.0 Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 Power Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Parts In Place Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3 Power Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.4 Machine Operation Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.5 Component Locator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.0 Machine Testing / Troubleshooting / Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.0 Schematic Section Map 230/460V- 0558007542 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.0 Schematic Section Map 400V/400V CE- 0558007546 . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.0 Schematic Section Map 575V- 0558007544 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Main Power Switch S1 (36107) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2 Control Transformer T2 (0558007188/0558008546) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.3 Input Bridge (0558007068 / 0558007077)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.4 Contactor K1 (950247 / 0558002576) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.5 Voltage Selector Switch SW2 (0558007183) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.6 Main Transformer T1 (0558007189 / 0558007190 / 0558007191) . . . . . . . . . . . . . . . . . . 30
4.7 Output Diodes D101, D102 – (951185) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.8 PCB1 Control/Display Board (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.8.1 PCB1_Bias Supplies (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.8.2 PCB1_Display (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.8.3 PCB1_Error Amp / Current Reference (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.8.4 PCB1_Mode Switches (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.8.5 PCB1_Protection Circuit (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.8.6 PCB1_Gas Test Operate Switch (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.8.7 PCB1_PWM Circuit (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.8.8 PCB1_RS232 Input (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.8.9 PCB1_Current Reference (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.8.10 PCB1_Programming Port(0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.8.11 PCB1_Thermal Sensing Circuit (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.8.12 PCB1_I/O (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.8.13 PCB1_Microcontroller U5 (0558038317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.9 Input Inductor L1 (0558007149/ / 0558007151) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.9.1 Output Inductor (0558007152) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.10 Power PC Board (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.10.1 Power PC Board Schematic (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.10.2 Power PC Board Schematic 2 (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.10.3 Power Board_PCB2 Bias Supply Circuit (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.10.4 Power PC Board Over Current Protection (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.10.5 Power PC Board_Pilot Arc / IGBT Driver Circuit (0558038315) . . . . . . . . . . . . . . . . . . . . 58
4.10.6 Power PC Board Single Phase Detection (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.10.7 Power Board_PCB2 Control Relays (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.10.7 Power Board_PCB2 Control Relays (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.10.8 Power Board_PCB2 Voltage Selection Circuit (0558038315) . . . . . . . . . . . . . . . . . . . . . 62
4.10.9 Power Board_PCB2 CNC Interface (0558038315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4
table of contents
5
CONTENTS
6
CONTENTS
5. Keep everything dry, including cloth- C. Do not place your body between the
ing, work area, cables, torch/Piston, and power torch and work cables. Route cables on the same
source. side of your body.
6. Make sure that all parts of your body D. Connect the work cable to the
are insulated from work and from ground. workpiece as close as possible to the area being
welded.
7. Do not stand directly on metal or
the earth while working in tight quarters or a damp E. Keep welding power source and
area; stand on dry boards or an insulating platform cables as far away from your body as possible.
and wear rubber-soled shoes.
7
CONTENTS
3. If you develop momentary eye, nose, or Standard P-1, “Precautions for Safe Handling of
throat irritation while operating, this is an indication Compressed Gases in Cylinders”, which is avail-
that ventilation is not adequate. Stop work and take able from Compressed Gas Association, 1235 Jef-
necessary steps to improve ventilation in the work ferson Davis Highway, Arlington, VA 22202.
area. Do not continue to operate if physical dis-
comfort persists.
EQUIPMENT MAINTENANCE -- Faulty
4. Refer to ANSI/ASC Standard Z49.1 (see or improperly maintained equipment can
listing below) for specific ventilation recommenda- cause injury or death. Therefore:
tions.
1. Always have qualified personnel perform
5. WARNING: This product, when used for the installation, troubleshooting, and maintenance
welding or cutting, produces fumes or gases which work. Do not perform any electrical work unless
contain chemicals known to the State of California you are qualified to perform such work.
to cause birth defects and, in some cases, cancer.
(California Health & Safety Code §25249.5 et seq.) 2. Before performing any maintenance work
inside a power source, disconnect the power
source from the incoming electrical power.
2. Always secure cylinders in an upright posi- 6. Use equipment only for its intended pur-
tion by chain or strap to suitable hand trucks, un- pose. Do not modify it in any manner.
dercarriages, benches, walls, post, or racks. Never
secure cylinders to work tables or fixtures where
they may become part of an electrical circuit.
ADDITIONAL SAFETY INFORMATION -- For more information on safe practices for electric arc
welding and cutting equipment, ask your supplier for a copy of “Precautions and Safe Practices for
Arc Welding, Cutting and Gouging”, Form 52-529.
The following publications, which are available from the American Welding Society, 550 N.W. LeJuene
Road, Miami, FL 33126, are recommended to you:
4. AWS C5.3 - “Recommended Practices for Air Carbon Arc Gouging and Cutting”
8. ANSI/AWS F4.1, “Recommended Safe Practices for Welding and Cutting of Containers That Have
Held Hazardous Substances.”
Means immediate hazards which, if not avoided, will result in immediate, serious per-
sonal injury or loss of life.
Means potential hazards which could result in personal injury or loss of life.
9
CONTENTS
Engineering control must be used to reduce exposures to safe levels (in compliance
with the new PEL). The specific details of the standard are complex and may require
the assistance of an occupational health professional to reach full compliance
For additional information about Hexavalent Chromium contact your occupational health professional
and read the OSHA web page at http://www.osha.gov/SLTC/hexavalentchromium/
10
CONTENTS
For additional information about Hexavalent Chromium contact your occupational health professional
and read the OSHA web page at http://www.osha.gov/SLTC/hexavalentchromium/
11
CONTENTS
section 2 INTRODUCTION
2.0 Introduction
2.0 Introduction
2.1 General
The Powercut 1600 is a compact plasma cutting system. As shipped, the system is fully assembled and
ready to cut after being connected to input power and a source of compressed air (350 cfh @ 90 psi / 6.2
bar). The Powercut package uses the heavy-duty PT-38 (manual plasma) torch to deliver cutting power for
selected materials up to 1.50 inch (38.1 mm) thick and severing selected materials up to 1.75 inch (45 mm)
thick
2.2 Scope
The purpose of this manual is to provide qualified repair personnel with technical information which will as-
sist in troubleshooting and repairing malfunctions.
12
CONTENTS
section 3 SPECIFICATIONS
3.0 Power Specifications
3.0 Specifications
13
CONTENTS
section 3 SPECIFICATIONS
3.1 Power Up Sequence
When the machine is turned on, a self diagnostic test is performed to determine the condition of the torch.
Sequence of events
The operator turns on the power switch
The Power Board PCB-1 determines if the input voltage is correct and connects input power.
The Control Board PCB-1 enables the In-rush circuit.
Power Board Relay K1 closes and pre-charges the buss supply.
The machine performs a Parts-in-Place check (PIP) and displays this on the front panel display. (See PIP
test, below)
If the PIP test passes the machine is ready for operation.
Parts-In-Place
The PC1600 performs a Parts In Place (PIP) check during initial power-up. The following steps are pre-
formed automatically each time power is applied:
14
CONTENTS
section 3 SPECIFICATIONS
3.4 Machine Operation Flowchart
15
CONTENTS
section 3 SPECIFICATIONS
3.5 Component Locator
PC1600 Components
Symbol Description Section # 4.
INDUCTOR INPUT
L1
REACTOR LINE 3 PHASE 9
L2 INDUCTOR OUTPUT
T1 TRANSFORMER MAIN 6
T2 TRANSFORMER CONTROL 2
BR1 BRIDGE RECTIFIER 110A 1600V 3
Q101,102 IGBT DUAL 150A 600V
5
Q103 IGBT 50A 1200V
D101,102 DIODE MODULE 100A 600V 7
PCB1 PC BOARD - CONTROL / DISPLAY 8
PCB2 PC BOARD - POWER 10
PCB3,4 PC BOARD - DRIVER BOARD 11
PCB5 PC BOARD - PILOT ARC DRIVER BOARD 13
PCB6 PC BOARD - REMOTE 18
PCB7 PC BOARD - EMC FILTER 50A 16
RELAY SPST 24VAC 20A(110VDC) w/ MAG BLOWOUT
K1 4
CONTACTOR 3P 40A 24VAC
M1 FAN 6” 230CFM 230V 2
SW1 SWITCH POWER 3P 60A 600V 1
SW2 SWITCH VOLTAGE SELECTOR 5
TS1 SWITCH THERMAL N/C 176°F
12
TS2 SWITCH THERMAL N/C 176°F - Solder
SOL1 SOLENOID 17
C37, C40,
BUSS CAPACITORS 10.16
C44,C47,
C101, C102,
BUSS CAPACITORS 10.16
C103, C104
16
CONTENTS
5
1 4
3 6 9
7
9 11 10
13
12 17
2
8 15 18
17
CONTENTS
SECTION 4 description of operation
4.0 Schematic Section Map 400V/400V CE- 0558007546
16 1
4 9
3
1 7
16 11 10
6
13
12 17
2
8 15 18
18
CONTENTS
SECTION 4 description of operation
4.0 Schematic Section Map 575V- 0558007544
1 4
3
9
11
7
16 10
6
13
12 17
2
8 15 18
19
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.1 Main Power Switch S1 (36107)
The main Power Switch is located on the front panel of the unit and passes main input power to the unit.
The switch is a triple pole, single throw, rotary type switch, rated for 63 amps of input current at 690 VAC.
T6 current transformer, located on the B leg of the S1 output is used to monitor for a single phasing condi-
tion. See section 4.10.6 for more information.
Switch testing:
With power disconnected from the unit:
Switch open:
From pole L1 of the switch to T1 of the switch - open Or High resistance
From pole L2 of the switch to T2 of the switch - open Or High resistance
From pole L3 of the switch to T3 of the switch - open Or High resistance
Switch Closed:
From pole L1 of the switch to T1 of the switch low resistance or shorted
From pole L2 of the switch to T2 of the switch low resistance or shorted
From pole L3 of the switch to T3 of the switch low resistance or shorted
20
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.2 Control Transformer T2 (0558007188/0558008546)
The auxiliary control transformer is used to step-down the input voltage to levels that can be used as sup-
ply voltages for the logic circuits in the PC1600. Since the PowerCut 1600 is available in with different input
voltage configurations, the control transformer has a multiple tap primary to allow it to be used in all ver-
sions. T2 supplies the following AC voltages to the bias supply circuits on the Power Board PCB3:
21
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.2 Control Transformer T2 (0558007188/0558008546)
Transformer T2 (0558007188)
Resistance
Lead Color Input Voltage
Leads Ohms
H1 RED Common
H2 GREY 230 H1 - H2 < 1 ohm
H3 BLUE 400 H1 -H3 < 1 ohm
H4 WHITE 460 H1 - H4 < 1 ohm
H5 ORANGE 575 H1 - H5 < 1 ohm
Output Voltage
X1/X2 RED/YELLOW 24 VAC X1 - X2 < 1 ohm
X3 BROWN 18 VAC X3 - X4 < 1 ohm
X4 BLACK CT 0 V
X5 YELLOW 18VAC X4 - X5 < 1 ohm
X6/X7 VIOLET 24 VAC X6 - X7 < 1 ohm
H1-H2 is excitation voltage
Ohms test Primary to Secondary. Any H connection to any X must
read “OPEN”
22
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.2 Control Transformer T2 (0558007188/0558008546)
23
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.2 Control Transformer T2 (0558007188/0558008546)
LEAD LIST
POINT COLOR LENGTH TERMINATION
TERMINAL VOLTAGE
H1 RED 12 AMP 2-520183-2
H1 - H2* 230 H2 GRAY 13 STRIP .38
H1 - H3 575.0 ± 1.0% H3 ORANGE 11 STRIP .38
X1 - X2 25.5V ± 1.0% X1 RED/YELLOW 12 STRIP .25
X3 - X4 20.5V ± 1.0% X2 RED/YELLOW 12 STRIP .25
X3 - X5 41.0V ± 1.0% X3 BROWN 12 STRIP .25
X6 - X7 26.8V ± 1.0% X4 BLACK 12 STRIP .25
X5 YELLOW 12 STRIP .25
*H1-H2 COIL IS EXCITATION WINDING
X6 VIOLET 12 STRIP .25
X7 VIOLET 12 STRIP .25
24
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.2.1 Axial Fan (951182)
The side mounted fan M1 is used to circulate cooling air across the active devices, (the IGBTs, IBR and
D101 and D102) inside the cabinet. The fan starts when the torch trigger is depressed and will continue to
run for up to seven minutes after the cut has ceased. There is a variable timing circuit at work here. The
timing circuit will keep the fan running for the same amount of time the torch was cutting. In other words,
if the torch was turned on for two minutes, the fan will continue to run for two minutes after the torch was
turned off. This 1:1 ratio will work up to a maximum of seven minutes. The maximum fan on time is seven
minutes after the torch is turned off.
Testing:
Open circuit resistance is 150 Ohms.
Specifications:
5.9 DIA. x 2.16 In., 247.2 CFM
230V 60Hz/ 55dB(A)/ -40 ~ +55°C
Metal housing and impeller
Shaded pole motor, air output over struts
Elec. connection via 2 leads AWG 18, 14 in. (365
mm) from outer edge of housing.
Mass = 38.8 oz (1100g)
.4 50 Hz 100
Static Pressure
6.375
.3
.2 50
6.75
.1
0 0
2.1875 5.875 OD 0 50 100 150 200 250 300 CFM
25
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.3 Input Bridge (0558007068 / 0558007077))
The input bridge is a 3 phase, full wave rectifier, which converts the AC input voltage to DC. The device is
designed to deliver a maximum current of 160 Amps of forward current.
Primary AC power enters the rectifier where it is rectified by the six diodes inside BR1. The rectified output
is coupled to the buss supply capacitors and the L1 input inductor.
A “precharge” Inrush circuit is mounted to the output of L1 and is in parallel with the Main Contactor. This
circuit allows the Buss supply to charge gradually during initial power up. When the operator closes the
torch trigger, the Main Contactor is used to supply full current output to the buss supply.
Testing: 760K Ohm forward resistance, reverse resistance - high resistance (1.5 Meg-Ohm or greater) out
of circuit. In circuit resistance is 99 K Ohm.
26
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.3 Input Bridge (0558007068 / 0558007077))
27
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.4 Contactor K1 (950247 / 0558002576)
The Main Contactor Relay K1 is the main power relay on this unit. When the torch switch is closed, the con-
trol board PCB1 supplies 24VAC to the coil of the relay. This allows the relay to energize which allows full
power to be applied to the filter buss.
DESCRIPTION:
AMPS: 40 INDUCTIVE
NO. OF POLES: 3
COIL VOLTAGE: 24
MAIN TERMINAL: BOX LUGS ON BOTH SIDE & DOUBLE
QUICK CONNECT ON LINE & LOAD
AUX. PWR. & COIL TERMINALS: .250 QUICK CONNECT
WIRE RANGE : 14-6 AWG
UL RECOGNIZED
CONTACTOR TO BE SUPPLIED WITH COVER OVER
CONTACTS
MTG SCREW = #10
NOTE: GRAPHIC FOR REFERENCE ONLY
28
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.5 Voltage Selector Switch SW2 (0558007183)
The Voltage Selector Switch is a three position switch designed to alter the configuration of the filter bus
to accommodate 230 VAC or 460 VAC input voltages. This switch is only in the 230/460 VAC selectable
models.
The filter caps are configured in two different ways in the PC1600 230/460 model, dependant upon the
input voltage. The power selector switch SW2 will place the four filter capacitors in either a series configu-
ration or in a parallel pair configuration.
The Voltage Selector switch is a three position switch with a center “Off” position. If this switch is changed
during normal operation, the system will shut down to prevent damage to the unit. The unit will remain inop-
erable until it is shut off and powered back up. If the voltage input is incorrect, the machine will give you a
voltage fault.
29
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.6 Main Transformer T1 (0558007189 / 0558007190 / 0558007191)
The Main Transformer T1 accepts the 18.5 KHz AC power from the IGBTs and steps the voltage down be-
fore sending it to the output diodes where it is rectified to DC before being sent out to the torch.
30
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.6 Main Transformer T1
31
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.7 Output Diodes D101, D102 – (951185)
OUT OF
+ - IN CIRCUIT
CIRCUIT
1 2 OPEN 20K
1 3 3.8K 14K
2 3 7.8K 4.8K
2 1 3.8K 900 ohms
3 1 OPEN 900 ohms
3 2 OPEN 12.2K
32
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8 PCB1 Control/Display Board (0558038317)
Description:
The main control board is responsible for most of the control functions of the PC1600. This board controls
the Pulse Width Modulator, CNC interface, power up sequence, gas pressure control, error signals and the
display. The board receives its’ power from the power board bias supplies to operate and also creates a
5VDC bias supply on board.
For the purpose of explanation and troubleshooting the board is broken down into sub-circuits. Board level
repair is not recommended.
33
CONTENTS
SECTION 4 description of operation
4.8 PCB1 Control Board (0558038317)
7 1
3
12
12
11 9
13
8 PCB1
6
5 10
4 2
34
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.1 PCB1_Bias Supplies (0558038317)
POWER
The Board receives +15 VDC and -15 VDC from the power board via the ribbon cable at J1. The +15 VDC
is connected on J1 pins 1 -4 (to divide the current among the 4 conductors) and passed to the +5VDC sup-
ply circuit and also distributed to the different circuits on the board.
The negative 15 VDC is brought in on the J1 connection at pins 5 and 6 , and then sent to the board cir-
cuits.
+5VDC Supply
The +15 VDC input is branched off to supply U1 which is being used as the regulator for the +5 VDC sup-
ply. This voltage is distributed throughout the board and to the current reference pot R69.
35
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.2 PCB1_Display (0558038317)
The Main control board microcontroller outputs the digital signals to the display driver chips. These chips
then drive the displays mounted on the control board.
36
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.3 PCB1_Error Amp / Current Reference (0558038317)
The Control board sets the current output level and receives the error signals from the hall sensors mount-
ed on the power board. The control board micro controller receives the current reference input current
reference circuit and then outputs that on U5 pin 47 as the SDO signal. This combined with the clock signal
SCK on U5 pin 45 set the current reference level on U4 and U6. These reference signals are summed
against the signals from the hall sensors to set the current signal.
37
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.4 PCB1_Mode Switches (0558038317)
The Mode select switch (SW4) is a three position switch used to determine the mode of machine operation.
In the up position the unit is in “Gas Test” mode, allowing air to flow through the torch for setting inlet pres-
sures.
In the center position, Normal Mode, the unit is in “Operate Mode.
In the down position,(Trigger Lock) the torch trigger can be released after an arc is established and the arc
will continue until the trigger is activated and released a second time.
SW4 is hard mounted directly to the control board, allowing the toggle to extend through the front panel.
Gas Test
Normal
Trigger Lock
38
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.5 PCB1_Protection Circuit (0558038317)
The Protection Circuit is designed to prevent the PC1600 from producing output current without a trigger
signal present. The comparator circuit senses if output current is above zero when the pwm_engage signal
is not present. It automatically shuts down the pwm circuit if that condition exists. This a redundant control
to ensure that a single circuit failure does not result in a dangerous output condition.
39
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.6 PCB1_Gas Test Operate Switch (0558038317)
The Display switch on the PCB1 control board allows the operator to choose the units of measurement for
the Gas, in Pounds per Squire Inch (PSIG) or in (Bars) to be displayed on the front panel LED display.
SW1-2 has no function. SW1 is hard mounted to the Main Control board.
With SW1-1 in the OFF position the unit will display gas pressure in PSI units.
With SW1-1 in the ON position the unit will display gas pressure in BAR units.
40
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.7 PCB1_PWM Circuit (0558038317)
Adjustment
Adjust R29 to read 38 KHz at TP1
Adjust R43 to read 1.45 VDC at TP3
41
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.8 PCB1_RS232 Input (0558038317)
The Serial Input circuit is used for the Power Board PCB2 to communicate to the Main Control Board. This
is an RS232 interface and is used primarily for the Power Board to identify itself to the Main Control board.
42
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.9 PCB1_Current Reference (0558038317)
The output current level of the PC1600 is set from the board mounted potentiometer (R69) that extends
through the front panel of the console.
The wiper of this pot is connected to the microcontroller through resistor R468. The pot is connected across
5 volts and ground. The resulting voltage divider from the wiper varies the voltage sent to the microcon-
troller. This varies the output of the PWM circuit, and so, varying the current output of the PC1600.
43
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.10 PCB1_Programming Port(0558038317)
The programming port on the board is used to program the main control board microcontroller at the fac-
tory. Field programming of the unit is not necessary.
The Main Control Board has a temperature sensing circuit built into it for circuit protection. If the tempera-
ture in the case exceeds 40 degrees centigrade(104 deg F), the microcontroller will shut down the unit.
The precision temperature sensor TH1 is connected to a comparator, U7A. When the voltage out from TH1
exceeds 400 millivolts the comparator sends out a signal to the microcontroller and the microcontroller
shuts the unit down.
44
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.12 PCB1_I/O (0558038317)
The control board sends and receives signals across the two ribbon cables connecting the Main Control
board to the Power Board. These two ribbon cables connected to the Main Control Board at J1 and J2 are
the I/O bus of the unit.
Control board J1 connects to Power board J4
Control board J2 connects to Power board J7
45
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.12 PCB1_I/O (0558038317)
J1 I/O Values
Signal Pin Value
+15 VDC 1
+15 VDC 2
+15 VDC
+15 VDC 3
+15 VDC 4
-15 VDC 5
-15 VDC
-15 VDC 6
Closes the Bus Charger Relay K1 on the Power Board
Bus Charger 7
PCB2
Closes the Mains Contactor Relay RL3 on the Power
MainsContactor 8
Board PCB2
Fan 9 Closes the Fan Relay RL2 on the Power Board PCB2
NONE 10 NOT USED
11 Output Inductor Thermal Switch TS2
Thermal HS 12 Heat Sink Thermal Switch TS1
Fault Bit 0 13 Fault bit output to CNC
Arc On 14 Arc On signal to the CNC
Pilot Arc On 15 Pilot Arc On signal to the CNC
Corner 16
M_Start 17 Torch Switch input
Turns on the Gas Valve Relay RL1 on the Power Board
Gas Valve 18
PCB2
he Microcontroller on the Main Control Board contains the programming necessary to run the PC1600.
Here the unit receives signals from the power board– (Start signal, current reference, Pilot Arc level …) and
acts upon them so as to get the plasma console to operate. Based on the input signals the microcontroller
will generate output signals to turn on the contactors, relays and pulses required to make the unit function.
The microcontroller also generates error messages and drives the front panel display.
The Microcontroller is not user programmable. Should a problem arise with the microcontroller or the Main
Control board, we recommend replacing the PCB.
46
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.14 PCB1 Layout (0558038317)
47
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.15 PCB1 BOM (0558038317)
PCB1 COMPONENTS
ITEM QTY DESCRIPTION SYMBOL
1 1 DRILLED BOARD
2 2 CAP, NET. 9 PIN SIP, 0.01uF CN1,CN2
3 2 CAP, 4.7uF, 50VDC, ALUM C1,C3
C2,C5,C7,C15,C19,C21,C25,C29,
4 13 CAP, 0.22uF, 100VDC, CER
C30,C32,C40,C44,C48
5 2 CAP, 0.0068uF, 100VDC, MET-POLY C4,C13
C6,C17,C18,C23,C24,C31,C41,C4
6 12 CAP, 0.01uF, 100VDC, FILM
2,C50,C51,C52,C53
7 2 CAP, 120uF, 25VDC, ALUM, ELECT. C8,C11
C9,C20,C22,C27,C28,
8 9 CAP, 0.1uF, 100VDC, FILM
C33,C36,C43,C45
9 4 CAP, 0.001uF, 100VDC, FILM C10,C14,C35,C46
10 2 CAP, 0.022uF, 100VDC, CER C12,C16
11 3 CAP, 560pF, 63VDC, MET-POLY C26,C34,C39
12 1 CAP, 47uF, 35VDC, ELECT. C37
13 3 CAP, 27pF, 300VDC, MICA C38,C47,C49
14 2 DIODE, ZENER, 5.6V, 1N4734A D1,D15
15 1 DIODE, SCHOTTKY, 31DQ05 D2
D3,D4,D5,D6,D7,D8,D9,D10,D11,
16 11 DIODE, SCHOTTKY, 11DQ05
D12,D13
17 1 DIODE, MUR160 D14
18 2 HEADER, HORIZ. RIBBON, 24 PIN J1,J2
19 1 HEADER, HORIZ, AMP, 5 PIN J3
20 1 INDUCTOR, 115uH, PE53820 L1
21 2 TRANSISTOR, FET, IRLD014 Q1,Q2
22 2 RES, NET. 8 PIN SIP, 10K RN1,RN5
23 1 RES, NET. 16 PIN DIP, 47 RN3
24 5 RES, NET. 16 PIN DIP, 470 RN4,RN6,RN8,RN9,RN10
25 1 RES, NET. 16 PIN DIP, 1K RN7
26 4 RES, 10, .25W, 1% R1,R15,R71,R76
27 1 RES, 2.8K, .25W, 1% R2
28 1 RES, TRIMPOT, 500 R3
R4,R7,R11,R12,R14,R17,R20,R22
,R23,R24,R25,R28,R30,R37,R45,
29 28 RES, 1K, .25W, 1%
R50,R51,R57,R58,R83,R85,R86,
R89,R90,R91,R92,R93,R98
48
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.8.15 PCB1 BOM (0558038317)
PCB1 COMPONENTS
ITEM QTY DESCRIPTION SYMBOL
30 8 RES, 10K, .25W, 1% R5,R19,R52,R59,R73,R78,R84,R87
31 10 RES, 4.99K, .25W, 1% R6,R18,R35,R36,R39,R40,R46,R48,R49,R64
R8,R13,R47,R53,R55,R62,R63,R68,R72,R75,
32 16 RES, 499, .25W, 1%
R79,R88,R94,R95,R96,R97
49
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.9 Input Inductor L1 (0558007149/ / 0558007151)
The Input Inductor L1 is a line reactor inductor used to filter out line noise in the 400 and 575 VAC units.
This is a three gang unit of three 170 micro-Henrys capable of passing 22 amps of current.
The Input Inductor L1 is a line reactor inductor used to filter out line noise in the 230 and 460 VAC units.
This is a 300 micro-Henry, 150 Amp unit.
50
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.9.1 Output Inductor (0558007152)
51
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10 Power PC Board (0558038315)
The power board in the PC1600 allows the power connections to be made in a solid, central way that
makes short power runs with hi power carrying capacity. All of the power carrying components are mount-
ed to PCB2.
52
CONTENTS
SECTION 4 description of operation
4.10.1 Power PC Board Schematic (0558038315)
8 7
7 19
17
20
9
15 13
17 11
18
5 11
16 17
12
10
6 4
53
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.2 Power PC Board Schematic 2 (0558038315)
8
14
54
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.3 Power Board_PCB2 Bias Supply Circuit (0558038315)
The Bias supply circuit provides the power necessary to operate the onboard circuitry of the PC1600. This
section provides three output voltages to the unit; +15VDC, -15VDC and +5 VDC.
Two 18 VAC inputs are applied to the board at J20 Pins 4, 5 and 6, With pin 5 being the grounded center
tap off the transformer.
This AC power is applied to a full wave rectifier, BR1 where it is converted to a pulsing 25 VDC. This puls-
ing DC is then filtered and passed to the regulator circuits.
The positive 15 VDC supply is filtered by C71 and C72, a pair of 1000 mfd capacitors. This power is then
connected to a five pin adjustable voltage regulator, U13. Output voltage is set by the voltage divider com-
prised of R94, R95 and R96. Pin 4 of the voltage regulator is connected to R95 a 500 trim pot that is used
to adjust the output voltage of the regulator. Output power is turned on or off by turning on the mosfet Q4.
When Q4 is forward biased, the Mosfet conducts and places a low on pin 5 of the regulator U13. The Q4
MOSFET is turned on by the microcontroller on the Power Board PCB2.
Power output from the regulator is filtered by C73 and C76, a pair of 1000 mfd capacitors, before being
passed to the needed circuitry.
The Negative output of the rectifier bridge BR1 is connected to Q5, which acts as a series pass device.
When Q5 is turned on, it allows power to be passed to the negative voltage regulator. Q5 is turned on when
Q6 is conducting. Q6 is placed in conduction when the microcontroller passes the enable_n15 signal to
the base of Q6. In this manner, the microcontroller on the Power Board can control the power supply. Once
Q5 is turned on and passing current, the negative supply is filtered by C77, a 1000 mfd filter capacitor. This
filtered output is then fed to U15 a three pin -15VDC regulator.
The +5vdc supply is fed from the positive filter section (C71 and C72) and connected to a three pin adjust-
able regulator U14. The output of this regulator is varied by R112 a 500 Ohm trim pot. This supply is always
active whenever the machine is powered up.
55
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.3 Power Board_PCB2 Bias Supply Circuit (0558038315)
56
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.4 Power PC Board Over Current Protection (0558038315)
The power board uses a pair of current transformers to detect an over current condition on the output of
the PC1600. In the event the output exceeds the rated current, the induced signal in the transformers shuts
down the power circuit at the control board microcontroller.
The output from each of the IGBTs is passed to the output transformer through the Current Transformers L1
and L2. The output of these transformers is rectified and then connected to a buffering IC. When the output
of this op amp exceeds the error threshold, the control board micro shuts down the PWM and sends an er-
ror to the display.
When the PC1600 is operating, current flowing out of Q101 to the output transformer flows through a wire
that passes through the Current Transformer L2. The expanding and contracting magnetic field of the wire
induces a voltage in the Current Transformer. The output of this transformer is connected to a full wave
bridge, D12, where it is rectified and passed to op amp U10A on pin 3 for buffering. The output of U10A on
pin 1 passes through D10 and is sent to the main control board PCB1 as signal bridge_peak. When this
voltage exceeds 2.75 VDC the main control board PCB1 will shut down the PWM and send an error to the
display.
When the PC1600 is operating, current flowing out of Q102 to the output transformer flows through a wire
that passes through the Current Transformer L1. The expanding and contracting magnetic field of the wire
induces a voltage in the Current Transformer. The output of this transformer is connected to a full wave
bridge, D14, where it is rectified and passed to op amp U11B on pin 5 for buffering. The output of U11B on
pin 7 passes through D15 and is sent to the main control board PCB1 as signal bridge_peak. When this
voltage exceeds 2.75 VDC the main control board PCB1 will shut down the PWM and send an error to the
display.
It should be noted that the 2.75 VDC is the greater of the two outputs of the current transformers. If either
one of them puts out a signal greater than 2.75 volts DC, the PWM circuit will shut down. These two signals
are compared and the greater of the two is present at R73 before passing to the main control board.
57
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.5 Power PC Board_Pilot Arc / IGBT Driver Circuit (0558038315)
The Pilot Arc IGBT is gated on from the Main Power board PCB-2 via an IC on the power board.
The Pilot Arc IGBT is gated on from U9 Pin 7. This output is enabled when the microcontroller toggles
on the PA relay signal to U9 pin 3. This places a high on U9 pin 7 that forward biases the Pilot Arc IGBT,
through the pilot arc driver board PCB-5.
58
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.6 Power PC Board Single Phase Detection (0558038315)
The power board monitors the the input power for loss of a phase when in three phase operation. This is
important as the microcontroller monitors the output duty cycle of the machine. The PC1600 is rated for
60% duty cycle at 90 amps of output current in three phase operation, and 40% duty cycle at 90 amps of
output current in single phase operation. Should the unit exceed the duty cycle, the microcontroller will shut
the machine down when the duty cycle limit is reached to prevent damage to the machine.
The single phase detection circuit monitors the output of T6. The AC voltage here is rectified by full wave
bridge D13. The output is then filtered by C61 and passed to the power board microcontroller as signal
mains_current.. A loss of voltage at T6 results in the loss of the mains_current signal. This loss tells the
micro control that the unit has lost a power input phase.
59
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.7 Power Board_PCB2 Control Relays (0558038315)
The Power Board has seven relays mounted on it. One is used as part of the Inrush circuit, and will be dis-
cussed there (See section 4.10.12, Inrush circuit)
The remaining relays RL1 – RL4, control other functions of the PC1600.
RL1 is the gas solenoid control relay. This relay is closed when the unit is commanded to flow air for pre-
flow, cutting operations and postflow. The signal used to close this relay comes from the control board.
RL2 is the fan relay. The fan relay closes when the unit begins a cutting operation. The fan will run as long
as the unit is cutting and will continue to run for seven and a half minutes after the unit has ceased cutting.
The signal used to close this relay comes from the control board.
RL3 is the main contactor relay. This relay closes the main contactor during cutting operations. The signal
used to close this relay comes from the control board.
RL4 – not used at this time
RL5 460 Off relay. This relay opens when 460 volts AC is NOT the input voltage
RL6 230 On relay. This relay closes when 230 VAC IS the input voltage.
60
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.7 Power Board_PCB2 Control Relays (0558038315)
61
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.8 Power Board_PCB2 Voltage Selection Circuit (0558038315)
The input voltage selection is controlled by the, manually set, position of S2 however the voltage selection
circuit on the power board will tell the power board micro-controller that the input power is 230 or any other
voltage. This allows the power board to render some protection against major damage should the incor-
rect voltage be applied. Two relays, RL5 and RL6 provide the logic for the micro based on signals from the
input.
It is the combination of these two signals and the V bias signal that tells the power board micro controller to
energize RL5 (the NOT 460 VAC relay) and RL6 (the 230 VAC relay). If the input power switch is changed
during operation, this circuit will notify the microcontroller and the unit will be disabled until it is powered
down and powered back up. If the input voltage is not correct (230 VAC applied while the input switch is in
the 460 VAC position) the power board micro will not enable the systems +/- 15VDC bias voltages.
62
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.8 Power Board_PCB2 Voltage Selection Circuit (0558038315)
The input voltage selection is controlled by the, manually set, position of S2 however the voltage selection
circuit on the power board will tell the power board micro-controller that the input power is 230 or any other
voltage. This allows the power board to render some protection against major damage should the incor-
rect voltage be applied. Two relays, RL5 and RL6 provide the logic for the micro based on signals from the
input.
It is the combination of these two signals and the V bias signal that tells the power board micro controller to
energize RL5 (the NOT 460 VAC relay) and RL6 (the 230 VAC relay). If the input power switch is changed
during operation, this circuit will notify the microcontroller and the unit will be disabled until it is powered
down and powered back up. If the input voltage is not correct (230 VAC applied while the input switch is in
the 460 VAC position) the power board micro will not enable the systems +/- 15VDC bias voltages.
63
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.9 Power Board_PCB2 CNC Interface (0558038315)
The PC1600 is designed to be used in a mechanized environment. The CNC interface connector J8 is used
to connect to the Remote board PCB6, which will interface with a CNC via the J2 Amphenol plug.
The J8 connector passes all signals but one, the external reference signal, to the main control board PCB1
through the PCB2 J4 - PCB1 J1 ribbon cable. The external reference signal, used to set the output current
of the PC1600 remotely, is connected to the main control board through the PCB2 J7 – PCB1 J2 ribbon
cable.
64
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.10 Power Board_PCB2 Output Circuit (0558038315)
The Output Circuit on the power board consists of the rectifier diodes, the snubber, the output inductor and
a pair of Hall sensors.
The output diodes D103 and 104 are connected directly to the power board. AC Power from the output
transformer is connected to these two diodes at the negative terminals. This 18 KHz output is rectified to
DC and then passed through the Hall sensors and out to the Electrode, Pilot Arc Lead and Work lead.
The Hall devices sense the current level and send a current sense signal to the control board where it is
used internally by the microprocessor and sent to the display board.
Hall sensor T5 detects torch and pilot arc current. Hall sensor T4 detects only the work current.
65
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.11 Power Board_PCB2 V-Arc Circuit (0558038315)
The V-Arc circuit is designed to notify the microcontroller on the Control board PCB1 of a low output volt-
age situation. Voltage input from the two tertiary windings is connected to the Power board PCB2. This
square wave AC is divided and connected to an electronic rectifier that outputs a DC reference voltage that
is connected to the Microcontroller of PCB1.
Voltage input on J14 and J15 from the tertiary windings of the main transformer are connected in phase
and passed first through a Ferrite inductor before being connected across a voltage divider network. Once
divided, the signal is connected to the non inverting input of U12b and passed out to a rectifier diode, D5.
This out put is divided again and connected to the non inverting input of U8A. This output is filtered by
66
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.12 Power Board_PCB2 Inrush Circuit (0558038315)
The Inrush circuit is designed to allow the filter buss to charge up at a lower current level so that when the
unit begins cutting the initial current draw does not cause an excessive current surge condition which could
damage the unit.
When the on board relay K1 closes, the filter capacitors charge through the thermistors R62 and R67.
These two thermistors restrict the amount of current drawn by the filter caps during their initial charge.
When the torch switch closes the control board PCB1 will then close the mains contactor K1 on the chassis
to allow full output current to be drawn through the mains contactor.
67
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.13 Power Board_PCB2 Pressure Transducer (0558038315)
The pressure transducer circuit provides the voltage to operate the pressure transducer and accepts the
gas pressure signal back from the device. This signal is then passed to the Main Control board.
The pressure transducer receives +5 volts DC across J10 pin 3 (+5 VDC) and pin 2 (DC common) The sig-
nal is returned from the transducer on pin 1. This signal is coupled to main control board on J7 pin 19 and
ranges from 0.2 to 4.9 VDC. This is equal to 0 – 100 psi of input pressure.
68
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.14 Power Board_PCB2 Relay Boost Circuit (0558038315)
The Relay Boost circuit provides a source of power to trip the source voltage relays in the event that the AC
three phase input voltage is below 210 VAC in the 230 VAC mode.
In the event that the input power is low Q7 is turned on and conducts sending source voltage down to Q8.
The microcontroller gates on Q8 with a series of pulses that charge C84 to approximately 14 VDC. This al-
lows the 12 VDC relays to close in the voltage protection circuit.
69
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.15 Power Board_PCB2 Torch Trigger Circuit (0558038315)
The Torch Trigger circuit consists of a 24 VAC signal that is rectified and passed to an opto isolator. The
output of the opto isolator is then connected to the to the control board as the START signal.
24VAC is sent out on J12 pin 2 and routed to either the PT38 torch trigger or to a CNC. Once the torch
switch is closed, the 24VAC is returned on J9 pin 2 and sent to D3, a full wave bridge. This rectifies the AC
signal and sends DC power out to the opto-isolator U7 to fire it. Once the opto-isolator is fired, the output
of U7 pin 5 is then sent to the control board via J4 pin 17.
70
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.16 Buss Supply/IGBT
71
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.16 Power Board_PCB2 Filter Buss/IGBT Circuit (0558038315)
The Inverter blocks of the PC1600 is where the stored energy in the buss supply (DC power) is converted
to AC and supplied on to the output bridge. Two half bridge inverters are used (allows 230/460 switching)
and the output from them is combined at the secondary of the main transformers (T1-A and T1-B).
Components used: 2- twin IGBT transistors, Q101 and Q102
4-Electrolytic Capacitors, C37, C40, C44 and C47
2- Main transformers T1-A and T1-B
The Filter Buss capacitors receive power from either the pre-charge of the inrush circuit or from the main
contactor K1. (See the inrush circuit for more detail) Once the bus is fully charged, each of the four filter
caps will have a nominal voltage of 162 VDC across it’s terminals. The filter caps then reduce the ripple
on the rectified voltage and supply the filtered bus voltage to the IGBT circuits. Each IGBT circuit (or half-
bridge) will have a nominal buss voltage of 325 VDC, whether configured for 230 VAC input or 460 VAC
input.
Capacitor Information
72
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.16 Buss Supply
Note: In the early models of the PC1600, the power board labeled the Buss supply capacitors with num-
bers that are different than the schematic.
Conversion Information:
Early model label Current models
C37 C104
C40 C102
C44 C103
C47 C101
Buss Supply
The inverter block filter section, known as the Buss Supply, comprises C37, C40, C44, C47, R14 and R15.
The purpose of this section is to transform the pulsating DC to a level DC operating voltage.
The drawing below represents the output of the input bridge BR1.
Buss Supply
The inverter block filter section, known as the Buss Supply, comprises C37, C40, C44, C47, R14 and R15.
The purpose of this section is to transform the pulsating DC to a level DC operating voltage.
73
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.16 Filter Buss
The drawing below represents the output of the input bridge BR1.
The bulk of the filtering is done when the capacitors C37,C40, C44, C47 charge. These large value capaci-
tors act as a well, resisting changes in voltage with an ebb and flow effect, charging and discharging in
contrast to the rise and fall of their input voltage. A graphical representation of this is shown in the drawing
below.
The resistors R14 & R15, are in place to bleed off the residual voltage in the capacitors once the power
supply is de-energized, and so they are referred to as “bleeder resistors”.
DCV
74
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.16 Power Board_PCB2 Filter Buss/IGBT (0558038315)
When the converter is on, the IGBT circuit delivers an 18.5 KHz AC power to the main transformers. The
IGBTs are gated on by signals from the driver boards and regulate the output of the PC 1600 (see Section
4.10.21).
Some filter capacitors hold charges for long periods of time. Charged capacitors can present a shock
hazard. It is not safe to assume the capacitors have been drained even if there is a bleeder resistor across
them. Technicians who work with high voltage supplies use a shorting rod or a shorting stick to be certain
that all the filters are drained before working on the equipment. High-energy capacitors can discharge vio-
lently, so it is important that the shorting rod contain a high- wattage resistor of around 20 ohms to keep the
discharge current reasonable.
The filter caps are configured in two different ways in the PC1600 230/460 model, dependant upon the in-
put voltage. The power selector switch S3 will place the four filter capacitors in either a series configuration
or in a parallel pair configuration.
In the 460 VAC mode of operation, the four capacitors are placed in series – all four capacitors connected
in a daisy chain, each capacitor dropping 162.5 VDC. (See Section 4.10.16 “Series connected”)
In the 230 VAC mode of operation, the four capacitors are divided up into two pairs. Each pair has two ca-
pacitors in series and then the pairs are placed in parallel with one another. (See Section 4.10.16 “Parallel
connected”) again each capacitor supplying 162.5 VDC.
In 400 VAC and 575 VAC units, the capacitors are in series. There is no power selector switch in the 400
VAC or the 575VAC units.
75
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.17 Power Board_PCB2 Microcontroller Circuit (0558038315)
The Microcontroller on the Power Board is responsible for the voltage selection logic and for identifying
itself to the main control board PCB1 across the serial interface. Pulses for the Pilot Arc IGBT driver are
developed here and sent to the driver circuit.
Also see:
Section 4.10.5 Pilot Arc Driver
Section 4.10.8 Input Voltage Selection
76
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.18 Power Board_PCB2 Thermal Switch Circuit (0558038315)
The Thermal switch circuit supplies +15 VDC out to the Thermal switch. This is then passed through the
thermal switch and returned to the power board where the voltage is passed to ground. The output of this
circuit is a logic low that is sent to the microcontroller on the Main Control Board PCB1. If the Thermal
switch opens, this will place a logic high on the microcontroller input and set a thermal fault on the PC1600.
The thermal interlock is “self-resetting” When the temperature of the monitored device cools to an accept-
able operating temperature, the fault is reset and output will return.
77
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.19 Power Board_PCB2 Gate Driver Circuit (0558038315)
The gate driver circuit accepts the gate pulses from the control board. Here the 19 KHz pulsed signals are
buffered and then sent to the IGBT driver boards.
Gate pulses from the control board are input on J7 pins 1 and 3. These are routed to U1 and U3 respec-
tively which buffers the signals and drives the power MOSFETs, Q1 and Q2, used to supply pulses to the
Power Driver boards PCB3 and PCB4.
78
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.20 Power Board_PCB2 RS232 Interface (0558038315)
The control board has an RS232 interface built into it that connects to the control board through the J7
ribbon cable header (header J2 on the control card). This is used for communication between the power
board controller and the main controller. This communication channel is also used for computer testing of
the machine, accessed through the J5 connector on the power board
79
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.21 Power Board_PCB2 Layout (0558038315)
80
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.21 Power Board_PCB2 BOM (0558038315)
81
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.21 Power Board_PCB2 BOM (0558038315)
R1,R5,R7,R8,R18,R25,R27,R28,R29R32,R35,
59 19 RES, 1K, 0.25W, 1%
R45,R49,R66,R77,R80,R93R111,R125
R2,R3,R12,R13,R14,R19,R24,R39,R55,R57,
60 19 RES, 100, 0.25W, 1% R60,R63,R65,R69,R73,R117,R118,
R121,R129
R23,R31,R34,R37,R41,R42,R43,R47,R48,
65 16 RES, 10K, 0.25W, 1%
R50,R51,R54,R68,R104,R126,R128
82
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.10.21 Power Board_PCB2 BOM (0558038315)
83
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.11 Power Driver _ PCB3 / PCB4 (0558038335)
84
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.11 Power Driver (0558038335)
85
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.11 Power Driver _ PCB3 / PCB4 (0558038335)
86
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.12 Thermal Switch TS1 (951085)
The thermal switch mounted on the heat sink between the IGBTs is a normally closed bimetallic switch that
will open if the temperature of the output inductor exceeds 176° F. The switch will remain open until the in-
ductor cools to 156° F. The switch is physically attached to the heat sink and connected to the power board
at J1. This switch is electrically connected to the Main Control Board Microcontroller through the PCB2
J4/PCB1 J1 ribbon cable. When TS1 opens, it drives error code 4, shutting down the IGBTs until the unit
cools. TS1 will “self reset” at 156° F allowing normal operation of the PC1600.
87
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.12 Thermal Switch TS2 (055807892)
The thermal switch mounted on the output inductor is a normally closed bimetallic switch that will open if
the temperature of the Output inductor exceeds 176° F. The switch will remain open until the inductor cools
to 156° F.
The switch is physically attached to the heat sink and connected to the power board at J16. This switch
is electrically connected to the Main Control Board Microcontroller through the PCB2 J4/PCB1 J1 ribbon
cable.
Note: When replacing TS2 a thin, uniform coating of heat sink compound must be applied to the mounting
surfaces.
88
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.13 Pilot Arc Driver Board PCB5 (05580038344)
The Pilot Arc IGBT is gated on when power is needed for pilot arc. The Main Power board PCB2 supplies
a signal form J23 pin 1 and 3 to the IGBT driver board (PCB5). A 12 VAC signal is received in on PCB5
pins 1 and 2, conditioned, filtered and then passed on to the gate connection of Q103 (pilot arc IGBT).
89
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.13 Pilot Arc Driver _ PCB5 (0558038344)
90
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.14 Help Codes
Primary over-
11 Converter failure. Send unit to an ARS for repair.
current
Single phase
Exceeded single phase duty cycle
12 operation, Operate within proper duty cycle rating.
rating.
shutdown
OCV (open circuit Voltage or current not detected Send unit to an Authorized Repair
13
voltage) failure when test (PIP) is performed. Station for repair.
91
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.15 Pressure Transducer (0558006148)
The Pressure Transducer is a 4 – 100 PSI unit designed to output 0 to 4.5 VDC to the control board as
feedback for the pressure output to the torch.
92
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.15 Pressure Transducer (0558006148)
93
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.16 EMC Filter 50A _ PCB7 ( CE Units _ 0455803880)
The EMC Filter board is used on the 575VAC/460VAC and 400 VAC CE units to further reduce the electro-
magnetic interference of the unit.
NOTE: This component is rated for handle 3 phase currents (50 amps Max).Single phase usage will cause
failure to the EMC filter.
94
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.17 Solenoid SOL1 (0558007072)
The Gas Solenoid SOL1 is a 24 VAC normally closed gas solenoid rated for 100 PSI. The valve is used as
a on/off control for the gas flow through the PC1600.
When the operator activates the torch trigger on the PC1600, the microcontroller on the main control board
sends a gas valve command to the power board PCB2. This command closes the contacts of relay RL1,
which applies 24 VAC to J13 pin 1 and pin 2 then to the gas solenoid coil.
95
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.18 Remote_PCB6 (0558038337)
The Remote Interface board allows the PC1600 to be controlled by a CNC in a mechanized plasma con-
figuration. This circuit board plugs into the Power Board and has a cable routed from the board to the front
panel of the PC1600 for the CNC interface. Reference Mechanized Conversion Kit Installation Instructions
for PC-1300/1600 part number 0558008079 for installation and conversion instructions if this unit did not
come with this option installed.
This circuit board accepts the following signals from the CNC:
The external reference input is a 0 – 10 VDC signal that is divided by two and sent to the Power Board
PCB2 for routing to the Control board PCB1.Reference the schematic.
The start signal will start and stop the power supply on CNC command. Reference the schematic.
The Corner signal is routed to the microcontroller on PCB1. When this signal is sent from the CNC, the
microcontroller ramps down the current to a level determined in software.
The ARC ON signal is sent to the CNC from the power supply. When the arc is detected by the PC1600,
PCB1 sends an active low signal to PCB6 P1 pin 8 which allows relay RL2 to close. This passes the ARC
ON signal out to the CNC.
When the PC1600 detects an internal fault the microcontroller on PCB1 puts an active low on PCB6 P1 pin
7 allowing relay RL1 to close and pass a fault signal out to the CNC.
96
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.18 Remote_PCB6 (0558038337)
97
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.18 Remote_PCB6 (0558038337) BOM
98
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
Cuts 1-1/2 in. (38 mm); severs 1-3/4 in. (45 mm)
Current Capacity 90 amps @ 100% duty cycle
Air Supply 400 cfh @ 80 psig (189 l/min @ 5.5 bar)
Length of Service Lines 25 (7.6 m) or 50 ft (15.2 m)
Dimensions
Overall Length 8.2 in. (208 mm)
Length of Head 3.0 in. (76 mm)
Torches and torch body assemblies are supplied without electrode, nozzle, heat shield and swirl baffle.
Order complete spare parts kits or individual components shown with PT-38 parts breakdown in section 2.3
Spare Parts Kits.
99
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
Nozzle
90A = 0558007680
70A = 0558005219
Torch On 40A = 0558007682
Electrode
Torch Off
0558005220
Retaining Cup
0558007549
Handle Set
Gas Baffle 0558006735
90A = 0558004870
Screw Blk Ox #6 x .5 Long
61950852
40-70A = 0558005217
Trigger Spring
0558006799 Trigger Switch
Torch Trigger 0558007878
0558006796
100
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
Cap
0558006790
Screw 0.164x32x.12
61330890
101
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
O-Ring
Cap
2223489
0558006790
Piston
0558006791
O-Ring
5W51
Brazed Body
0558006789
102
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
103
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
104
CONTENTS
SECTION 4 DESCRIPTION OF OPERATION
4.19 PT38 Plasma Torch
105
CONTENTS
section 5 WIring diagrams
5.1 Wiring Diagram 230/460 Volt (0558007543)
106
CONTENTS
section 5 WIring diagrams
5.1 Wiring Diagram 230/460 Volt (0558007543)
107
CONTENTS
section 5 WIring diagrams
5.1 Wiring Diagram 230/460 Volt (0558007543)
108
CONTENTS
section 5 WIring diagrams
5.2 Wiring Diagram 400/400V CE (0558007547)
109
CONTENTS
section 5 WIring diagrams
5.2 Wiring Diagram 400/400V CE (0558007547)
110
CONTENTS
section 5 WIring diagrams
5.2 Wiring Diagram 400/400V CE (0558007547)
111
CONTENTS
section 5 WIring diagrams
5.3 Wiring Diagram 575V (0558007545)
112
CONTENTS
section 5 WIring diagrams
5.3 Wiring Diagram 575V (0558007545)
113
CONTENTS
section 5 WIring diagrams
5.3 Wiring Diagram 575V (0558007545)
114
CONTENTS
blank
115
CONTENTS
6.1 General
Always provide the serial number of the unit on which the parts will be used. The serial number is
stamped on the unit nameplate.
6.2 Ordering
To ensure proper operation, it is recommended that only genuine ESAB parts and products be used
with this equipment. The use of non-ESAB parts may void your warranty.
Be sure to indicate any special shipping instructions when ordering replacement parts.
Refer to the Communications Guide located on the back page of this manual for a list of customer ser-
vice phone numbers.
Note
Bill of material items that have blank part numbers are provided for customer information
only. Hardware items should be available through local sources.
116
CONTENTS
T1
230/460V pn: 0558007189 SW2
400V pn: 0558007190 pn: 0558007183
575V PN:0558007191
T2
pn: 0558007188
L2 C37,40,44,47
pn: 0558007152 pn: 0558007162
R13
L1
pn: 17300001
230/460V pn:0558007151
400/575V pn: 0558007149
117
CONTENTS
PRESSURE TRANSDUCER
pn: 0558006148
PCB2
PCB3, PCB4
pn: 0558038335
SOL1
K1 pn: 0558007072
PRESSURE REGULATOR
pn: 0558007071
118
CONTENTS
PCB5
pn: 0558038344
Q103 PCB1
pn: 0558007866 pn: 0558038317
SW2
pn: 0558007183
Q101 - Q102
BR1
PCB2
119
CONTENTS
section 6 replacement parts
6.3 Front (0558007540)
120
CONTENTS
section 6 replacement parts
6.3 Front BOM
121
CONTENTS
section 6 replacement parts
6.3 Right Interior View (0558007540)
122
CONTENTS
section 6 replacement parts
6.3 Right Interior View BOM
PC1600 REPLACEMENT PARTS
ITEM QTY P/N DESCRIPTION SYMBOL
1 1 0558007196M BASE
2 1 0558007202 BRACKET FAN
4 1 0558007201 BRACKET FMR
5 1 0558007203 SHELF
7 1 0558007204 BO PCB
14 SEE SECT 6.4 INDUCTOR INPUT L1
15 1 0558007152 INDUCTOR OUTPUT L2
16 FMR MAIN 230/460V T1
SEE SECT 6.4
17 FMR CONTROL 208/230/400/460V T2
HEATSINK (SCREEN TOOL
23 1 0558007154
0558954072)
38 1 17300001 RESISTOR 1 OHM 300W R13
41 1 17712001 RESISTOR 0.1 OHM 25W 5% R2
42 1 0558008454 KIT FAN 6” 230CFM 230V w/ PLUG M1 / P3
SWITCH THERMAL N/C 176°F -
46 1 0558007892 TS2
Solder
STANDOFF NYLON FEMALE #6-32
89 4 0558007212 HE 3/4” LG
90 2 0558007211 BRACKET ANGLE GLASTIC
GROMMET RUBBER 0.44ID 0.56GD
107 1 993837 .06W
GROMMET RUBBER 2.50ID 2.75GD
110 8 0558007070 .06W
114 1.63’ 99510498 TUBING PVC, 600V, 1/2” BLACK
115 .38’ 2132496 TUBING PVC, 600V, 5/8” BLACK
116 .33’ 90863100 HEATSHRINK 1” BLACK
STRIP RUBBER FOAM 0.25 WIDE
118 1.75’ 22529001 .063 THK.
TERM, WIRE JOINT INS, 18-16
124 2 634736 AWG
126 1 46N08 ROD THREADED #8-32 9.75” LG
127 2 647182 WASHER INSULATING MICA
128 2 91W19 WASHER CENTERING
136 61325826 SCREW SQ PAN TRI #4-40 .38
137 AR 61325849 SCREW SQ PAN TRI #6-32 .25
141 AR 61325902 SCREW SQ PAN TRI #10-24 .50
145 AR 61328087 SCREW HE WSH TRI 1/4-20 .50
149 AR 61341087 SCREW HE CAP 1/4-20 .50
151 2 04S04060 SCREW PHL PAN SST M4 60
153 AR 61327747 SCREW HE WSH TAP #8 .4 RIBBED
159 AR 64304887 WASHER FLAT #8
160 AR 64304050 WASHER FLAT #10
164 AR 64302837 WASHER LOCK #4
165 AR 64302860 WASHER LOCK #6
166 AR 64302887 WASHER LOCK #8
167 AR 64302920 WASHER LOCK #10
168 AR 64302996 WASHER LOCK 1/4
171 AR 64307887 WASHER LOCK ET #8
175 AR 04W10041 WASHER LOCK M4
178 AR 63300886 NUT #8-32
179 AR 63300916 NUT #10-24
180 AR 63300100 NUT 1/4-20
207 AR 180W68 TYWRAP SM 4”
208 AR 631507 TYWRAP MED 5.5”
209 AR 180W66 TYWRAP LG 7.25”
213 AR 76200103 SOLDER .031 DIA
COMPOUND ELECTRICAL JOINT
215 AR 73585980 ALCOA #2
123
CONTENTS
section 6 replacement parts
6.3 Top (0558007540)
124
CONTENTS
section 6 replacement parts
6.3 Top BOM
125
CONTENTS
section 6 replacement parts
6.3 Left Inside (0558007540)
126
CONTENTS
section 6 replacement parts
6.3 Left Inside BOM
45 1 951085 SWITCH THERMAL N/C 176°F TS1
CONNECTOR IDC 6 PIN 22awg
58 1 0558003430 - Red PT P1
62 1 0558003429 COVER IDC CONNECTOR 6 PIN
HOUSING UNIV CAP 12 POS
67 1 951109 - Wht J1
KIT TRANSDUCER PRESSURE
72 1 0558008354 2-100 PSI w/ HOSE PT
VALVE SOLENOID 3-WAY 75
73 1 0558007072 PSID 24VAC SOL1
REGULATOR PRESSURE 7-125
74 1 0558007071 PSI
ELBOW 90° 1/4 OD TUBE
76 1 0558007075 1/8NPTM
ELBOW 90° 5/16 OD TUBE
77 2 0558004184 1/4NPTM
78 2 0558006292 ELBOW STREET 90° 1/4NPT
79 1 0558005635 COUPLING BODY QD 1/4NPTM
80 1 67101075 NIPPLE 1/4NPT 7/8”LG
KIT HOSE POLYURETHANE 3/16
82 1 0558008083 ID 5/16 OD Red (21”)
83 - - -
GROMMET RUBBER (0.12-0.31)
105 1 0558007073 ID 0.50GD .06W
GROMMET RUBBER 0.31ID
106 5 97W34 0.44GD .06W
GROMMET RUBBER 0.44ID
107 1 993837 0.56GD .06W
GROMMET RUBBER 0.63ID
108 6 92W57 0.88GD .06W
GROMMET RUBBER 2.50ID
110 8 0558007070 2.75GD .06W
113 1.13’ 90861726 TUBING PVC, 300V, #1 BLACK
SHEET INSULATING (6.25” 3”)
117 1 0558008065 Nome
122 SEE SECT 6.4 POWER CORD 6awg 4 Conductor
136 61325826 SCREW SQ PAN TRI #4-40 .38
137 AR 61325849 SCREW SQ PAN TRI #6-32 .25
139 AR 61325878 SCREW SQ PAN TRI #8-32 .38
140 AR 61325881 SCREW SQ PAN TRI #8-32 .63
141 AR 61325902 SCREW SQ PAN TRI #10-24 .50
147 AR 61308903 SCREW PHL PAN #10-24 .625
SCREW HE WSH TAP #8 .4
153 AR 61327747 RIBBED
158 AR 64304860 WASHER FLAT #6
160 AR 64304050 WASHER FLAT #10
162 AR 05W01055 WASHER FLAT M5
164 AR 64302837 WASHER LOCK #4
165 AR 64302860 WASHER LOCK #6
167 AR 64302920 WASHER LOCK #10
171 AR 64307887 WASHER LOCK ET #8
176 AR 05W10051 WASHER LOCK M5
179 AR 63300916 NUT #10-24
182 AR 63610862 NUT LOCK NYLON SST #6-32
184 AR 99510492 RIVET 1/8 (.032-.125)
207 AR 180W68 TYWRAP SM 4”
BASE TYWRAP SNAP-IN
211 AR 99511578 .218MH
COMPOUND HEATSINK DOW
214 AR 73585976 340 - White
COMPOUND ELECTRICAL
215 AR 73585980 JOINT ALCOA #2
ADHESIVE THREADLOCKER
218 AR 73585435 LOCTITE 242 - Blue
127
CONTENTS
section 6 replacement parts
6.3 Left Inside2 (0558007540)
128
CONTENTS
section 6 replacement parts
6.3 Left Inside2 BOM
PC1600 REPLACEMENT PARTS
ITEM QTY P/N DESCRIPTION SYMBOL
18 - 952002 TOROIDAL CORE L3
19 1 0558007180 BUSSBAR DIODE (+)
20 1 0558007181 BUSSBAR DIODE (-)
29 1 0558038317 PC BOARD - CONTROL / DISPLAY PCB1
PC BOARD - POWER 90 AMP -
30 SEE SECT 6.4 PCB2
230/460, 400V
31 2 0558038335 PC BOARD - DRIVER POWER PCB3,4
33 SEE SECT 6.4 PC BOARD - REMOTE PCB6
49 1 0558007738 KIT MOV 625VAC 230J D1,2,3
51 SEE SECT 6.4 KIT JUMPER - MECHANIZED LOGIC P11
55 2 0558007217 ASSY RIBBON CABLE 24 PIN 12” P1/P4 , P2/P7
56 8 952064 CONNECTOR IDC 2 PIN 20awg - Yel P9,12-17,19
57 1 952067 CONNECTOR IDC 3 PIN 20awg - Yel P10
60 8 952065 COVER IDC CONNECTOR 2 PIN
61 1 952068 COVER IDC CONNECTOR 3 PIN
CONNECTOR MINI-COMBICON 2
63 3 0558007184 PIN P1,3,21
CONNECTOR MINI-COMBICON 8
64 1 0558007185 PIN P20
65 CONNECTOR COMBICON 3 PIN P44
66 SEE SECT 6.4 CONNECTOR COMBICON 10 PIN P1
68 RECEPTACLE / CABLE ASSY 14 PIN J2
85 4 0558007160 SPACER ALUM #10 ID 1.0” LG
86 5 0558007159 SPACER ALUM 1/4 ID 7/16” LG
STANDOFF ALUM FEMALE #6-32
87 6 0558007158 HE 1-1/8” LG
88 6 0558007078 STANDOFF PLASTIC PCB 7/8” LG
91 1 0558007891 SPACER CABLE BUNDLE
116 .33’ 90863100 HEATSHRINK 1” BLACK
SCREW SQ PAN TRI #10-32 .38 w/
131 AR 61387910 LW
SCREW PHL HE #10-32 .50 w/ FLW
132 AR 0558006557 Blk
133 10 0558002087 SCREW PHL HE w/ FLW M5 12
134 5 0558006737 SCREW PHL HE w/ FLW M6 12
138 AR 61325851 SCREW SQ PAN TRI #6-32 .38
142 AR 61325087 SCREW SQ PAN TRI 1/4-20 .50
143 AR 61325090 SCREW SQ PAN TRI 1/4-20 1.00
148 4 61308904 SCREW PHL PAN SST #10-32 1.50
149 AR 61341087 SCREW HE CAP 1/4-20 .50
150 AR 05S12025 SCREW SKT HE M5 25 Blk
153 AR 61327747 SCREW HE WSH TAP #8 .4 RIBBED
165 AR 64302860 WASHER LOCK #6
167 AR 64302920 WASHER LOCK #10
168 AR 64302996 WASHER LOCK 1/4
176 AR 05W10051 WASHER LOCK M5
179 AR 63300916 NUT #10-24
180 AR 63300100 NUT 1/4-20
206 SEE SECT 6.4 CLAMP CABLE STEEL .375 DIA
207 AR 180W68 TYWRAP SM 4”
208 AR 631507 TYWRAP MED 5.5”
209 AR 180W66 TYWRAP LG 7.25”
210 AR 950908 TYWRAP PUSH-IN LG 6.75”
COMPOUND ELECTRICAL JOINT
215 AR 73585980 ALCOA #2
129
CONTENTS
section 6 replacement parts
6.3 Rear View (0558007540)
130
CONTENTS
section 6 replacement parts
6.3 Rear View BOM
131
CONTENTS
section 6 replacement parts
6.3 Front/Rear Isometric Views (0558007540)
132
CONTENTS
section 6 replacement parts
6.3 Front/Rear Isometric Views BOM
133
CONTENTS
section 6 replacement parts
6.4 Model Specific Parts BOM
MECH 230/460V
MECH 400V CE
0558007230F
230/460V BL
0558008323
0558007884
0558007234
0558007883
0558007230
0558007636
0558007237
230/460V
575V BL
400V CE
400V
460V
ITEM # Part # Description Symbol
INSULATOR SM EMC
1 1 12 0558008672
FILTER PCB Kydex
1 1 1 0558007151 INDUCTOR INPUT
REACTOR LINE 3 PHASE
1 1 1 0558007149
14 22A L1
REACTOR LINE CE 3
1 1 0558008732
PHASE 22A
1 1 1 1 0558007189 XFMR MAIN 230/460V
1 16 0558007191 XFMR MAIN 575V T1
1 1 1 0558007190 XFMR MAIN 400V
XFMR CONTROL
1 1 1 1 1 1 1 0558007188
17 208/230/400/460V T2
1 0558008546 XFMR CONTROL 230/575V
BUSSBAR 3PH
2 2 2 21 0558007527
CONTACTOR
BRIDGE RECTIFIER 110A
1 1 1 1 1 0558007068
1600V
24 BR101
BRIDGE RECTIFIER 160A
1 1 1 0558007077
1600V
0558006151 IGBT DUAL 150A 600V
2 2 2 2 2 2 2 25 0558008052 IGBT DUAL 200A 600V Q101,102
2 0558005462 IGBT DUAL 150A 1200V
PC BOARD - POWER 90
1 1 1 1 1 1 1 0558038323 AMP - 230/460, 400V
USE Dwg# 0558038315
30 PCB2
PC BOARD - POWER 90
1 0558038347 AMP - 575V
USE Dwg# 0558038315
1 33 0558038337 PC BOARD - REMOTE PCB6
PC BOARD - EMC FILTER
1 1 34 455803880 PCB7
35A
CAPACITOR ALUM 4100uF
4 4 4 4 4 0558007161
300VDC
36 C101-104
CAPACITOR ALUM 5400uF
4 4 4 0558007162
300VDC
RELAY SPST 24VAC
1 1 1 1 1 0558002576 20A(110VDC) w/ MAG
37 BLOWOUT K1
CONTACTOR 3P 40A
1 1 1 950247
24VAC
134
CONTENTS
section 6 replacement parts
6.4 Model Specific Parts BOM
MECH 230/460V
MECH 400V CE
0558007230F
230/460V BL
0558008323
0558007884
0558007234
0558007883
0558007230
0558007636
0558007237
230/460V
575V BL
400V CE
400V
460V
ITEM # Part # Description Symbol
SWITCH VOLTAGE
1 1 1 44 0558007183 SW2
SELECTOR
KIT JUMPER -
1 1 51 0558008111 P11
MECHANIZED LOGIC
1 1 1 1 1 0558954069 OVERLAY Bilingual Codes
52
1 1 1 0558954070 OVERLAY Plain
CONNECTOR COMBICON
1 1 65 951005 P44
3 PIN
CONNECTOR COMBICON
1 1 66 951016 P1
10 PIN
RECEPTACLE / CABLE
1 1 68 0558007890 J2
ASSY 14 PIN
ADAPTOR 1/4NPTM 1/4 ID
1 1 1 81 30354
HOSE
STRAIN RELIEF SEALED
1 1 95 526652
1/2” ZINC
1 1 96 2062151 LOCKNUT CONDUIT 1/2”
1 2 2 2 2 1 1 103 23610197 PLUG HOLE .875 DIA
CLOSURE TAPERED
1 1 1 1 1 111 60909075
CAPLUG #4
POWER CORD 6awg 4
1 1 1 0558007192
Conductor
POWER CORD 10awg 4
1 1 1 122 0558007193
Conductor
POWER CORD CE 6mm 4
1 1 0558007194
Conductor
TERM, WIRE JOINT INS,
2 2 2 2 2 2 2 124 634736
18-16 AWG
SCREW SLT PAN TAP #10
4 4 4 154 61326903
x .38
LABEL RATING
1 1 1 0558954073
208/230/460V PC-1600
LABEL RATING 460V PC-
1 0558954152
1600
LABEL RATING 575V PC-
1 186 0558954074
1600
LABEL RATING 400V PC-
1 0558954075
1600
LABEL RATING 400V CE
1 1 0558954161
PC-1600
135
CONTENTS
section 6 replacement parts
6.4 Model Specific Parts BOM
MECH 230/460V
MECH 400V CE
0558007230F
230/460V BL
0558008323
0558007884
0558007234
0558007883
0558007230
0558007636
0558007237
230/460V
575V BL
400V CE
400V
460V
ITEM # Part # Description Symbol
LABEL WARNING
1 1 190 0558954085 GENERAL ARC WELD &
CUT French
LABEL CAUTION
1 1 1 196 0558954064 VOLTAGE SELECT
SWITCH Bilingual
1 1 198 954565 LABEL CE - Trash Bin
LABEL CONSUMABLE
1 1 1 1 1 0558954090 BREAKDOWN PT-38
Bilingual
200 LABEL CONSUMABLE
1 0558954137
BREAKDOWN PT-38 CE
LABEL CONSUMABLE
1 1 0558954159
BREAKDOWN PT-37 (90A)
LABEL CUSTOMER
1 1 1 1 202 0558954034
ASSISTANCE
1 1 1 1 203 954506 LABEL ISO 9001
CLAMP CABLE STEEL
1 1 206 2235784
.375 DIA
WIRE KIT VOLTAGE
1 1 1 223 0558007207
SELECTOR SWITCH
WIRE KIT DUAL VOLTAGE
1 1 1 224 0558007208
POWER
WIRE KIT SINGLE
1 1 1 1 1 225 0558007209
VOLTAGE POWER
1 1 226 0558007210 WIRE KIT CE 400V
136
CONTENTS
section 7 mechanized conversion
7.0 MECHANIZED CONVERSION
137
CONTENTS
section 7 mechanized conversion
2. Assemble the strain relief onto the 14 pin cable as shown and partially tighten.
3. Remove the hole plug on the top right side of the back of the unit.
138
CONTENTS
section 7 mechanized conversion
4. Cut the tie wraps, unplug control transformer wires to allow for easier cable
routing (on a multi-voltage unit unplug voltage select switch wires also).
139
CONTENTS
section 7 mechanized conversion
7. Tighten the strain relief nut from the inside first ..;.....
pin 1 is blank
140
CONTENTS
section 7 mechanized conversion
10. Connect the pc board to the main power control board as shown below.
Secure the pc board to the frame with the screw provided.
fast-on connectors
141
CONTENTS
section 7 mechanized conversion
14. Route the "2-wire cable" downward b ehind the shelf brace.
15. Locate the 3-pin connector on the existing main power control board
3-pin connector
16. Align the 3-pin connector with the pc board header to identify which end of the connector aligns with
the "+" and "-" on the pc board. On the connector, insert the red wire to the "+" and black wire to the "-"
from the "2-wire cable" as shown and tighten.
142
CONTENTS
section 7 mechanized conversion
driver pc board
5-pin jumper
mounting pillars
143
CONTENTS
section 7 mechanized conversion
20. Trim all tie wraps and replace the unit's cover.
144
CONTENTS
section 8 ErrorS
8.0 ERRORS
8.0 Error 13
Error Number 13
SW1
Error 13
Possible cause: E13 says that the machine failed the PIP test because no current was detected. Check the
following
1- Consumables, anything that would prevent the electrode from touching the nozzle
2- Open torch leads, check power cable and pilot arc leads
3- Tertiary winding, check connections and wires at J14 and J15.
SW1
145
CONTENTS
section 8 errorS
8.0 Error 13
Reset
146
CONTENTS
section 8 ErrorS
8.1 Error 15
Error 15
Possible cause: E15 says that the machine failed to get voltage buildup on the Buss Capacitors
C101,C102,C103, and C104.
1- Check input power
2- Check input bridge output
3- Check “pre-charge circuit” on power board. If the power board has just been replaced check posi-
tion of J15, try position 1 and2 first, if error 15.
Err 15 must be rest internally in Program version 1, 1.01 and 1.02. With version 1.03, it is rest by pow-
ering down and powering up the PC1600
147
CONTENTS
section 9 Program Changes
9.0 Program Changes
Program changes:
Program Rev # Date Change
148
CONTENTS
SECTION 10 General information
10.0 General Information
10.1 Maintenance
A maintenance schedule should be created and based on the following variables, amount of usage, place-
ment of machine and cleanliness of local environment. A maximum time between should be no more the
90 days.
External: Check work cable for worn insulation and confirm tight electrical connections. Check safety
ground ground at work piece and at power source. Check torch cables for worn insulation and confirm tight
electrical connections. Drain any moisture from the bowl of the input filter / regulator.
Internal: Check for discolored connections as they indicate a loose connection. Check all plugs, fittings
and electrical connections for tightness. Make sure cables and hoses are not damaged, flattened or kinked.
With input power disconnected and wearing proper eye and face protection, blow out accumulated dirt and
foreign materials for the inside of unit. Extra attention should be given to the finned heatsinks.
Water or oil occasionally accumulates in compressed lines. Be sure to direct the first blast of air
away from the equipment to avoid damage to the EPP400
149
CONTENTS
SECTION 10 General information
10.2 Electrostatic Discharge
WARNING!
STATIC ELECTRICITY can damage circuit
boards and electronic components.
• Observe precautions for handling electrostatic
sensitive devices.
• Use proper static-proof bags and boxes.
What is ESD?
A sudden transfer or discharge of static electricity from one object to another. ESD stands forElec-
trostatic Discharge.
ESD can cause damage to sensitive electrical components, but is not dangerous to people.ESD
damage occurs when an ungrounded person or object with a static charge comes intocontact with
a component or assembly that is grounded. A rapid discharge can occur,causing damage. This
damage can take the form of immediate failure, but it is more likelythat system performance will be
affected and the component will fail prematurely.
ESD damage can be prevented by awareness. If static electricity is prevented from buildingup on
you or on anything at your work station, then there cannot be any static discharges.Nonconductive
materials (e.g. fabrics), or insulators (e.g. plastics) generate and hold staticcharge, so you should
not bring unnecessary nonconductive items into the work area. It is obviously difficult to avoid all
such items, so various means are used to drain off anystatic discharge from persons to prevent
the risk of ESD damage. This is done by simpledevices: wrist straps, connected to ground, and
conductive shoes.
Work surfaces, carts and containers must be conductive and grounded, use only antistaticpackag-
ing materials. Overall, handling of ESD–sensitive devices should be minimized to prevent damage.
150
CONTENTS
SECTION 10 General information
10.3 Ohm’s and Watt’s Laws
151
CONTENTS
SECTION 10 General information
10.4 Glossary
Device in series with a load which opens the circuit if its current
Fn FUSE n A, n V rating (A) is exceeded.
A diode that permits high current flow without damage, the reverse
Dn ZENER DIODE voltage remains almost constant over a wide range of currents, used
esp. to regulate voltage.
Dn LIGHT EMITTING Semiconductor diode that emits light when conducting current
DIODE
SILICON Device having primary and secondary inductors for altering a-c signal
SCR CONTROLLED amplitudes, impedance matching,and isolation purposes. . A reverse
RECTIFIER blocking triode thyristor
Wound wire device; current through the coil generates a electro-
Ln COIL magnetic field causing inductive reactance, which increases with
number of turns and density.
Wound wire device with a primary and secondary coil(s) which increases
Tn TRANSFORMER or decreases voltage applied to the primary based on coil and core
configuration. 1:1 transformers are used for isolation.
Identifies the earth (ground) connection. NOTE: Not for a protective
GROUND earth connection.
152
CONTENTS
SECTION 10 General information
10.4 Glossary
Mn Mn MOTOR n Ø,HP,V A device which converts electrical energy to mechanical energy (motion).
n
n
n
n
or Kn RELAY n A, n V Electro-mechanical device for opening / closing a circuit.
n
or
WIRE NODE Schematic representation of physical connection of wires.
Short for binary digit, the smallest unit of information processed by a computer.
BIT A single bit can hold only one of two values: 0 or 1.
As used in this manual BitI refers to input data, and BitO refers to output data.
153
CONTENTS
SECTION 10 General information
10.4 Glossary
LOGIC SYMBOLS
OR
INPUT OUTPUT
A A B X = A+B
X OR GATE
B 0 0 0
0 1 1
1 0 1
1 1 1
A NAND gate can have two or more inputs. The 'o' on the output means
'not' showing that it is a Not AND gate. The output of a NAND gate is
true unless all its inputs are true.
NAND
A INPUT OUTPUT
X NAND GATE A B X=A B
B
0 0 1
0 1 1
1 0 1
1 1 0
A NOR gate can have two or more inputs. The 'o' on the output means
'not' showing that it is a Not OR gate. The output of a NOR gate is true
when none of its inputs are true.
NOR
INPUT OUTPUT
A A B X=A+B
X NOR GATE
B 0 0 1
0 1 0
1 0 0
1 1 0
A NOT gate can only have one input. The 'o' on the output means 'not'.
The output of a NOT gate is the inverse (opposite) of its input, so the
output is true when the input is false. A NOT gate is also called an
inverter.
A X NOT NOT
INPUT OUTPUT
(INVERTER)
A X=A
0 1
1 0
154
CONTENTS
SECTION 10 General information
10.5 Meter Use
In all series circuits, the total circuit voltage is dropped across the load or electrical devices. The higher the
resistance of the load the higher the voltage drop. The lower the load resistance the lower the voltage drop.
An open contact in a branch circuit with a load will show a high voltage drop because the meter and the
open switch have a very high resistance when compared to the load. While a closed contact that has a me-
ter across, it shows a very low voltage drop since the resistance across the switch is lower than the load.
So, using the meter set at the proper voltage range you can test if the contacts are closed or open.
155
CONTENTS
SECTION 10 General information
10.6 Ohm Testing
156
CONTENTS
SECTION 10 General information
10.7 Diode Testing
157
CONTENTS
SECTION 10 General information
10.8 Ripple
158
CONTENTS
SECTION 10 General information
10.9 Voltage Measurement
159
CONTENTS
SECTION 10 General information
10.10 Generic IGBT Testing
Since IGBT gates are insulated from any other conducting region, care should be taken to prevent static
build up, which could possibly damage gate oxides. All IGBT modules are shipped from the factory with
conductive foam contacting the gate and emitter sense pins. Always ground parts touching the gate pins
during installation. In general, standard ESD predictions application to FETs should be followed.
When mounting IGBT modules on a heatsink, certain precautions should be taken to prevent any damage
against a sudden torque. If a sudden torque (“one-sided tightening”) is applied at only one mounting termi-
nal the ceramic insulation plate or silicon chip inside the module may get damaged.
The mounting screws are to be fastened in the order shown below, also, care must be taken to achieve
maximum contact (i.e. minimum contact thermal resistance) for the best heat dissipation.
Application of a thermal pad on the contact surface improves it thermal conductivity. See Replacement
Parts section for the required pad.
When an IGBT fails in these “inverter” units, BOTH IGBTs must be replaced. Failure of a transistor will sub-
ject stress into the circuit, and on the input bridge. It is advised that the input bridge also be replaced when
a transistor failure has occurred.
Two-Point Mounting Four-Point Mounting
Temporary Tighting ------ 1 2 Temporary Tighting ------ 1 2 3 4
Final Tightening ------ 2 1 Final Tightening ------ 4 3 2 1
1 1
3
4
2
2
160
CONTENTS
SECTION 10 General information
10.10.1 IGBT Testing
With meter on “OHMS (:)” setting, measure resistance Connect a 9 VDC battery with the negative on the Emitter
by placing the red (+) lead on the Collector (C1) and (E1) and the positive on the Gate (G1). The meter should
the black (-) lead on the Emitter (C2E1) of the IGBT. register a low reading.
The Gate should remain on once it has activated. Short the Emitter / Gate (G1-E1) leads to turn the IGBT off.
161
CONTENTS
SECTION 10 General information
10.10.1 IGBT Testing
With meter on “OHMS (:)” setting, measure resistance by Connect a 9 VDC battery with the negative on the Emitter
placing the red (+) lead on the Collector (C3 E1) and the (E2) and the positive on the Gate (G2). The meter
black (-) lead on the Emitter (E2) of the IGBT. should register a low reading.
The Gate should remain on once it has activated. Short the Emitter / Gate (G2-E2) leads to turn the IGBT
off.
162
CONTENTS
SECTION 10 General information
10.10.1 IGBT Testing
163
CONTENTS
SECTION 10 General information
10.10.1 IGBT Information
IGBT TESTING
NOTE:
Small amounts of dirt between mating surfaces can cause com-
ponent failure or degraded performance; DO NOT use silicon
seal or other adhesives in place of thermal paste.
164
CONTENTS
SECTION 10 General information
10.11 Buss Supply Power Control / IGBT / MOSFET Testing
IGBT Tester
1. Connect as shown
2. Led On = Shorted Junction, Replace Part
3. Press Push-button Switch:
Led On = Good
Led Off = Bad Or Open, Replace Part
NOTE:
Black lead always on emitter
Red lead always on collector
Yellow on gate connections
G1 = GATE 1
G2 = GATE 2
E1 = EMITTER 1
E2 = EMITTER 2
C1 = COLLECTOR 1
C2 = COLLECTOR 2
1. Connect as shown
2. Led On = Shorted Junction, Replace Part
3. Press Push-button Switch:
Led On = Good
Led Off = Bad Or Open, Replace Part
G = Gate
D = Drain
S = Source
165
CONTENTS
Index
166
CONTENTS
revision history
167
ESAB subsidiaries and representative offices
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
ESAB AB
SE-695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
101217