Scribd Logo
Upload

Welcome to Scribd!

  • 118 views

    Zzze) I (ZFRP: QW-163 Acceptance Criteria - Bend Tests QW-163 Acceptance Criteria - Bend Tests

    Uploaded by

    SARSAN NDT
    This document provides specifications for testing welded joints. It describes requirements for bend tests, notch toughness tests using Charpy V-notch and drop weight methods, and fillet weld tests. For bend tests, any discontinuities in the weld cannot be more than 1/8 inch wide, and for cladding cannot be more than 1/16 inch wide. Notch toughness tests must meet standards for location and orientation. Fillet weld tests involve preparing coupons and cutting specimens to specified dimensions from production mockups or welded joints to test fracture properties and for macroexamination.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content

    Zzze) I (ZFRP: QW-163 Acceptance Criteria - Bend Tests QW-163 Acceptance Criteria - Bend Tests

    Uploaded by

    SARSAN NDT
    118 views1 page
    This document provides specifications for testing welded joints. It describes requirements for bend tests, notch toughness tests using Charpy V-notch and drop weight methods, and fillet weld tests. For bend tests, any discontinuities in the weld cannot be more than 1/8 inch wide, and for cladding cannot be more than 1/16 inch wide. Notch toughness tests must meet standards for location and orientation. Fillet weld tests involve preparing coupons and cutting specimens to specified dimensions from production mockups or welded joints to test fracture properties and for macroexamination.

    Original Description:

    hypiu

    Original Title

    181.2

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides specifications for testing welded joints. It describes requirements for bend tests, notch toughness tests using Charpy V-notch and drop weight methods, and fillet weld tests. For bend tests, any discontinuities in the weld cannot be more than 1/8 inch wide, and for cladding cannot be more than 1/16 inch wide. Notch toughness tests must meet standards for location and orientation. Fillet weld tests involve preparing coupons and cutting specimens to specified dimensions from production mockups or welded joints to test fracture properties and for macroexamination.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    118 views1 page

    Zzze) I (ZFRP: QW-163 Acceptance Criteria - Bend Tests QW-163 Acceptance Criteria - Bend Tests

    Uploaded by

    SARSAN NDT
    This document provides specifications for testing welded joints. It describes requirements for bend tests, notch toughness tests using Charpy V-notch and drop weight methods, and fillet weld tests. For bend tests, any discontinuities in the weld cannot be more than 1/8 inch wide, and for cladding cannot be more than 1/16 inch wide. Notch toughness tests must meet standards for location and orientation. Fillet weld tests involve preparing coupons and cutting specimens to specified dimensions from production mockups or welded joints to test fracture properties and for macroexamination.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 1

    2010 SECTION IX

    When specimens wider than 11⁄2 in. (38 mm) are to be location, and the orientation shall be as given in the Section
    bent as permitted in figure QW-462.2, the test jig mandrel requiring such tests.
    must be at least 1⁄4 in. (6 mm) wider than the specimen When qualifying pipe in the 5G or 6G position, the
    width. notch-toughness specimens shall be removed from the
    shaded portion of figure QW-463.1(f).
    QW-163 Acceptance Criteria — Bend Tests
    The weld and heat-affected zone of a transverse weld- QW-180 FILLET-WELD TESTS
    bend specimen shall be completely within the bent portion
    QW-181 Procedure and Performance
    of the specimen after testing.
    Qualification Specimens
    The guided-bend specimens shall have no open disconti-
    nuity in the weld or heat-affected zone exceeding 1⁄8 in. QW-181.1 Procedure. The dimensions and preparation
    (3 mm), measured in any direction on the convex surface of the fillet-weld test coupon for procedure qualification
    of the specimen after bending. Open discontinuities as required in QW-202 shall conform to the requirements
    occurring on the corners of the specimen during testing in figure QW-462.4(a) or figure QW-462.4(d). The test
    shall not be considered unless there is definite evidence coupon for plate-to-plate shall be cut transversely to pro-
    that they result from lack of fusion, slag inclusions, or vide five test specimen sections, each approximately 2 in.
    other internal discontinuities. For corrosion-resistant weld (50 mm) long. For pipe-to-plate or pipe-to-pipe, the test
    overlay cladding, no open discontinuity exceeding 1⁄16 in. coupon shall be cut transversely to provide four approxi-
    (1.5 mm), measured in any direction, shall be permitted mately equal test specimen sections. The test specimens
    in the cladding, and no open discontinuity exceeding 1⁄8 in. shall be macro-examined to the requirements of QW-183.
    (3 mm) shall be permitted along the approximate weld QW-181.1.1 Production Assembly Mockups. Pro-
    interface. duction assembly mockups may be used in lieu of
    QW-181.1. The mockups for plate-to-shape shall be cut
    transversely to provide five approximately equal test speci-
    QW-170 NOTCH-TOUGHNESS TESTS

    ZZZE]I[ZFRP
    mens not to exceed approximately 2 in. (50 mm) in length.
    QW-171 Notch-Toughness Tests — Charpy For pipe-to-shape mockups, the mockup shall be cut trans-
    V-Notch versely to provide four approximately equal test specimens.
    QW-171.1 General. Charpy V-notch impact tests shall For small mockups, multiple mockups may be required to
    be made when required by other Sections. obtain the required number of test specimens. The test
    Test procedures and apparatus shall conform to the specimens shall be macro-examined to the requirements
    requirements of SA-370. of QW-183.
    QW-171.2 Acceptance. The acceptance criteria shall QW-181.2 Performance. The dimensions and the prep-
    be in accordance with that Section specifying impact aration of the fillet-weld test coupon for performance quali-
    requirements. fication shall conform to the requirements in figure
    QW-171.3 Location and Orientation of Test QW-462.4(b) or figure QW-462.4(c). The test coupon for
    Specimen. The impact test specimen and notch location plate-to-plate shall be cut transversely to provide a center
    and orientation shall be as given in the Section requiring section approximately 4 in. (100 mm) long and two end
    such tests. sections, each approximately 1 in. (25 mm) long. For pipe-
    When qualifying pipe in the 5G or 6G position, the to-plate or pipe-to-pipe, the test coupon shall be cut to
    notch-toughness specimens shall be removed from the provide two quarter sections test specimens opposite to
    shaded portion of figure QW-463.1(f). each other. One of the test specimens shall be fracture
    tested in accordance with QW-182 and the other macro-
    examined to the requirements of QW-184. When qualifying
    QW-172 Notch-Toughness Tests — Drop Weight
    pipe-to-plate or pipe-to-pipe in the 5F position, the test
    QW-172.1 General. Drop weight tests shall be made
    specimens shall be removed as indicated in figure
    when required by other Sections.
    QW-463.2(h).
    Test procedures and apparatus shall conform to the
    requirements of ASTM Specification E 208. QW-181.2.1 Production Assembly Mockups. Pro-
    duction assembly mockups may be used in lieu of the fillet-
    QW-172.2 Acceptance. The acceptance criteria shall weld test coupon requirements of QW-181.2.
    be in accordance with that Section requiring drop weight (a) Plate-to-Shape
    tests. (1) The mockup for plate-to-shape shall be cut trans-
    QW-172.3 Location and Orientation of Test versely to provide three approximately equal test specimens
    Specimen. The drop weight test specimen, the crack starter not to exceed approximately 2 in. (50 mm) in length. The

    You might also like