Professional Documents
Culture Documents
HydrolysisH PDF
HydrolysisH PDF
Experiment No. 8
Reaction Kinetics
Abstract:
The hydrolysis of an ester (ethyl acetate) in acidic solution will be studied for different
temperatures. For each temperature, the progress of the reaction will be tracked by
pH measurements after certain time steps, which will in turn yield the reaction rates.
Using the Eyring model, the temperature dependent reaction rates will be used to
calculate activation energy and entropy.
1. Theory
The reaction of ester hydrolysis is chosen for this experiment for practical reasons.
First, it takes place with rather low rates, so that changes can be observed on time
scales of minutes. Second, it requires an acid as catalyst. The amount of products
can thus be followed as a function of time by extracting small amounts (= aliquots)
from the reacting solution at certain time intervals. Diluting these aliquots by water
will virtually stop the reaction and allow for an analysis without any hurry. Third, the
product itself is an acid, so that its concentration can be easily and precisely
determined by titration.
In the following, we will first summarize the most important facts about acid-base
reactions and the procedure of titration, i.e., the tool to follow the progress of our
model reaction. We will then have a closer look at the reaction itself. The final two
sections of theory concern the determination of the rate constant and the
interpretation of its behaviour as a function of temperature.
Arrhenius defined an acid as a substance that increases the hydrogen ion (H+)
concentration of an aqueous solution, and a base as a substance that increases the
hydroxide ion (OH-) concentration. According to the Brønsted-Lowry theory of acids
and bases, any substance that gives up a proton is an acid (proton donor), and any
substance that can combine with a proton and remove it from solution is a base
(proton acceptor). In aqueous solution, acids (base) are classified as either strong or
weak. Strong acids (bases) are completely dissociated or ionized. Weak acids
(bases) dissociate only partially. When an acid (base) loses its proton (hydroxide), it
becomes the conjugate base (acid). Ionized means that a (H+) is transferred from the
acid molecule to a water molecule, to form a hydronium ion (H3O+). Completely
ionized means that each acid molecule transfers its acidic hydrogen atom as ion to a
water molecule. For the case of incomplete ionization, only a fraction of the acid
molecules loses their acidic hydrogen atoms.
equation (1.1) and for the example of the reaction between NaOH and HCl in
equation (1.2).
Acid (aq) + Base (aq) ↔ Water (l) + Salt (aq) reaktion (0.1)
HCl (aq) + NaOH (aq) ↔ H2O (l) + NaCl (aq) reaktion (0.2)
Other types of acid-base reactions besides reactions of strong acids and bases are
reactions of strong acids/bases and weak bases/acids (see any basic textbook of
chemistry for further information).
The acidity or basicity of a solution is given by the pH value. It can be calculated via
+ +
pH = - log10 ([H3O ]), where [H3O ] denotes the concentration of the hydronium ions
and is given in mol / litre. A pH value of 7 describes a neutral solution. Is the value
lower than 7, the solution becomes acidic, and if it is bigger than 7, the solution
becomes alkaline.
The amount of acid (base) present in a solution can for example be determined by
titration. This involves adding a standardized solution called titrant (from a burette) to
a flask containing the sample, called analyte, until the solution is neutralized. Neutral-
ization means determining the stoichiometric point (also known as equivalence
point), at which the amount of substance of the protons (or proton acceptors) n1 of
the titrant equals the amount of substance of the proton acceptors (or protons) n2 of
the analyte.
The stoichiometric point can for instance be optically detected, by adding a so called
indicator to the analyte. Depending on the pH value of the analyte, the chemical
structure of the indicator changes and hence it changes the colour of the solution.
A common indicator, also used in this experiment, is phenolphthalein, shown in
figure 1. It turns colourless in acidic solutions and pink in basic solutions. If the
concentration of indicator is particularly strong, it can appear purple.
CH3 C
O CH 2 CH3
+
The formal reaction equation of the H -ion catalysed hydrolysis of the ethyl acetate is
shown in Figure 3, where k1 and k2 describe the reaction rate constants of the
forward and reverse reaction, respectively.
O O
k1
CH3 C + H 2O + H+ CH3 C + H3CCH 2OH + H +
k2
O CH 2CH3 OH
Figure 3. Reaction scheme for the H+-ion catalysed hydrolysis of ethyl acetate.
In our experiment, H2O will be available in excess, which shifts the equilibrium
virtually fully to the right hand side. For completeness, Figure 4 shows the reaction
mechanisms with all its intermediate steps.
EST Introductory Laboratory (Physical Chemistry), Exp. No. 8: Kinetics | Ester Hydrolysis 5
OH
O OH
H+ H2O
CH3 C CH3 C CH3 C OCH 2CH3
O CH 2CH3 O CH 2CH3
H O H
OH OH
+
H+ H
CH 3 C OCH 2 CH 3 CH 3 C OCH 2 CH 3
H
OH OH
- H3CCH2OH OH OH OH
OH OH OH
O
H+
CH3 C
OH
The rate equation of the ester hydrolysis in Figure 3 may be written as:
d[EA]
= −k1[EA][H2O][H+ ] + k 2 [S][HAc][H+ ] (0.3)
dt
[EA] = concentration of ethyl acetate,
Since the experiment is carried out in a solution of a strong acid (HCl) that serves as
+
catalyst, the concentration of [H ] will not change during the reaction. Though the
generation of acetic acid (HAc; weak acid) from the hydrolysis goes along with a
+
slight increase in the [H ] concentration, this effect is too little to have an effect on
the reaction rate. The equation (0.3) can thus be simplified to:
d[EA]
= −k1[EA][H2O] + k 2 [HAc][A] (0.4)
dt
Also water is present in such excess that its concentration remains unchanged
during the reaction and can thus be included into the rate constant. On the other
hand, this excess reduces the possibility of the reverse reaction so that the term
k2[HAc][A] can be neglected. Thus, the rate constant equation (0.4) becomes a
"pseudo first order" reaction under these circumstances.
d[E]
= −k '[E] (0.5)
dt
k ' = k1[H2O]
EST Introductory Laboratory (Physical Chemistry), Exp. No. 8: Kinetics | Ester Hydrolysis 7
The temperature dependence of the reaction rate constant can be expressed with
the Arrhenius equation:
−Ea
k = A ⋅ e RT (0.6)
kBT #
k= K (0.7)
h
kB = Boltzmann's constant
h = Planck's constant
#
K = equilibrium constant of the transition state of the reaction
For the transition state the Gibbs energy can be written as follows:
By setting up two equations for the rate constants k(T1) and k(T2), at the different
temperatures, T1 and T2, and by dividing those two equations, the following
expression is obtained:
∆S # ∆H#
exp exp −
k 2 (T2 ) T2
= R RT2
k1(T1 ) T2 ∆S # ∆H#
exp e xp − (0.10)
R RT1
k 2 (T2 ) T2 ∆H# 1 1
= exp −
k1(T1 ) T2 R T1 T2
From equation (0.10), ∆G 0# , ∆H #0 und ∆S0# for the transition state can be calculated.
EST Introductory Laboratory (Physical Chemistry), Exp. No. 8: Kinetics | Ester Hydrolysis 8
2. Experimental Procedure
Experimental steps:
At any time (t) the volume of the titrant (Vt, NaOH) is measured (with a burette) and
noted. For a complete reaction, a volume V∞ for the titrant can be determined. Since
a complete hydrolysis can not be achieved experimentally, it has to be determined
theoretically. The final volume V∞ (equation (1.11)) contains on the one hand the
volume necessary to neutralise the HCl (VHCl) and on the other hand the volume to
neutralise the acetic acid formed from the ethyl acetate (VHAc).
Let’s first concentrate on the volume VHCl, which is needed to neutralise the HCl
included in the 5 ml samples (from the mixed solution: HCl + Ester). The volume can
be expressed by equation (1.12), where Vx stands for the prior determined titrant
volume to neutralise 5 ml of the heated HCl (as described under point 3 of the
experimental procedure). VS stands for the volume of the reaction solution. Due to
the non-ideal reaction solution its total volume is not 105 ml, but should be assumed
to be only 104.6 ml.
VX ⋅100 ml
VHCl = (0.12)
VS
To determine the titrand volume VE needed to neutralise the acetic acid formed after
complete hydrolysis in a aliquot of 5 ml of the mixed solution, it is only necessary to
know the initial concentration of our ethyl acetate. All the needed data for further
calculations at different temperatures are given in table 1.
Ethyl acetate
V [ml] 5
M [g/mol] 88.11
The amount of substance (n) of the initial ethyl acetate is given by equation (1.13).
m V ⋅ ρ 5ml ⋅ρ
n= = = (0.13)
M M M
The amount of substance of ethyl acetate in a 5 ml sample (nE) pipetted from the
reaction solution is given by equation (1.14).
To calculate the volume of the needed titrant, nE has to be equal to the amount of
substance of the NaOH (nOH), which leads to equation (1.15). Here cOH is the
concentration of the NaOH, obtained in step 1 of the experimental procedure and
VHAc is the volume of NaOH needed to neutralise the formed acetic acid.
Combining equation (0.14) and (0.15), VHAc can be expressed with equation (1.16).
1 1 25ml ⋅ρ
VHAc = ⋅ nE = ⋅ (0.16)
cOH cOH VS ⋅ M
Now the final titrand volume V∞ can be calculated and results in:
VX ⋅100 ml 1 25ml ⋅ ρ
V∞ = + ⋅ (0.17)
VS cOH VS ⋅ M
VHCl VHAc
Results Sheet
Names: _______________________
_______________________
_______________________
2. Hydrolysis at T1 = 298.15 K
used NaOH
Vtitr / mL
3. Hydrolysis at T1 = 308.15 K
used NaOH
Vtitr / mL
Colloquium topics
Basics of chemical kinetics
• Definition of the reaction rate
• Extend of reaction, order and molecularity of a reaction
• Rate law’s (zero, first, second order)
• Determination of the reaction order
• Relation between kinetics and thermodynamics
• Temperature dependence of the reaction rate
Further reading
Titration: http://www.dartmouth.edu/~chemlab/techniques/titration.html