Professional Documents
Culture Documents
A Seminar Report On UNMANNED AERIAL VEHICLE
A Seminar Report On UNMANNED AERIAL VEHICLE
Seminar Report
On
UNMANNED AERIAL VEHICLE
By
B one
EGME
Submitted for partial fulfillment of the requirements for award the degree of
BACHELOR OF TECHNOLOGY
(Mechanical Engineering)
Submitted to-
Mechanical Department
1|Page
TABLE OF CONTENTS
Chapter No. Description Page No.
1) Frount Page 1
2) Table of Content 2
3) Abstract 3
4) Introduction 4
5) UAV TYPES 6
6) Technical Specification 7
7) Block Diagram 8
8) Component of UAV 9
9) Advantages 15
10) Disadvantages 17
11) Discussion 18
12) Conclusion 20
2|Page
Abstract
UAV is an aerial vehicle operated to fly independently and. They are controlled by pilots on
ground or simultaneously driven. They are called rotorcrafts because unlike a fixed wing aircraft,
here lift is generated by a set of revolving narrow-chord aerofoils. Drones are actually very
fascinating and in this project we are going to study about them, their components and about its
widespread applications that determine its scope for the future. They are a mixture of streams of
Electronics, Mechanical and especially Aviation.
Drones are of different types and have different configurations for example, bicopters, tricopters,
UAV, hexacopters, octocopters, etc. They have different uses and accordingly respective
configurations are used. Hexacopters and Octocopters have better stability and yaw configuration.
Control of motion of vehicle is achieved by altering the rotation rate of one or motor discs, thereby
changing its torque load and thrust/lift characteristics. The use of four rotors in a UAV allow the
individual rotors to have a smaller diameter than the equivalent helicopter rotor, which allows
them to possess less kinetic energy during flight.
UAV have different structures and designs according to the work needed to be done by it.
Components like motors, batteries, electronic speed controllers (ESC‟s) also vary according to the
power needed and work done by the UAV. Also enhancements like GPS trackers or cameras or
infrared cameras are used so that they could add value to missions like disaster relief, search and
rescue, agriculture and 3D mapping of the geography of an area.
These widespread applications outshine the disadvantages which are rectifiable and hence this
makes it a very productive technology in today‟s world. It is supposed to appear into full time
existence in the coming years. But every technology has merits as well as demerits. It is up to us to
use technology productively to enhance the people as well as the planet instead of using them
destructively. For instance, exploitation of drones by using them for spying and other lethal
purposes that can harm people
3|Page
Introduction:
An unmanned aerial vehicle (UAV), also known as a unmanned aircraft system (UAS), remotely
piloted aircraft (RPA) or unmanned aircraft, is a machine which functions either by the remote
control of a navigator or pilot (called a Combat Systems Officer on UCAVs) or autonomously, that
is, as a self-directing entity. One can differentiate the UAVS from missiles as the UAVS are not
remotely guided by an operator, while the missiles are remotely operated by a user at the military
base. UAVS can fly autonomously and donot carry a human operator. Although UAVS come in
two varieties one are remotely operated and the second type of them fly without any help.
The birth of US UAVS took when the United States Air Force is considered about losing of pilots
over the hostile territory, began considering about the UAVS.
History:
The earliest attempt at a powered unmanned aerial vehicle was A. M. Low's "Aerial Target" of
1916. Nikola Tesla described a fleet of unmanned aerial combat vehicles in 1915. A number of
remote-controlled airplane advances followed, including the Hewitt-Sperry Automatic Airplane,
during and after World War I, including the first scale RPV (Remote Piloted Vehicle), developed
by the film star and model airplane enthusiast Reginald Denny in 1935. More were made in the
technology rush during World War II; these were used both to train antiaircraft gunners and to fly
attack missions. Jet engines were applied after World War II, in such types as the Teledyne Ryan
Firebee I of 1951, while companies like Beechcraft also got in the game with their Model 1001 for
the United States Navy in 1955. Nevertheless, they were little more than remote-controlled
airplanes until the Vietnam Era.
In the United States, the United States Navy and shortly after the Federal Aviation Administration
has adopted the name unmanned aircraft (UA) to describe aircraft systems without the flight crew
on board. More common names include: UAV, drone, remotely piloted vehicle (RPV), remotely
piloted aircraft (RPA), remotely operated aircraft (ROA), and for those "limited-size" (as defined
by the FAI) unmanned aircraft flown in the USA's National Airspace System, flown solely for
recreation and sport purposes such as models and radio control (R/Cs), which are generally flown
4|Page
under the voluntary safety standards of the Academy of Model Aeronautics, the United States'
national aeromodeling organization.
The term unmanned aircraft system (UAS) emphasizes the importance of other elements beyond
an aircraft itself. A typical UAS consists of the:
5|Page
UAV Types:
UAVs typically fall into one of six functional categories (although multi-role airframe platforms
are becoming more prevalent):
Target and decoy – providing ground and aerial gunnery a target that simulates an enemy
aircraft or missile
Combat – providing attack capability for high-risk missions (see Unmanned combat air
vehicle)
Civil and Commercial UAVs – UAVs specifically designed for civil and commercial
applications
They can also be categorised in terms of range/altitude and the following has been advanced as
relevant at such industry events as ParcAberporth Unmanned Systems forum:
MALE (medium altitude, long endurance) up to 30,000 ft (9,000 m) and range over 200 km
HALE (high altitude, long endurance) over 30,000 ft (9,100 m) and indefinite range
6|Page
TECHNICAL SPECIFICATIONS
While the overall goals, strategies and objectives have been stated, the specifications of the
components will be determined as they are identified for their applicability in the project. The
technical specifications are divided in the following in engineering module on the basis of
application and engineering involved. The modules are represented in Table 3.1.
7|Page
Block Diagram of a UAV
MOTORS
DRIVERS
M D D M
O R R O
T I I T
O V V O
MICROCONTROLLER
R E E R
S R R S
S S
DRIVERS
MOTORS
8|Page
Components of a UAV
The main components used for construction of a UAV are the frame, propellers (either
fixed-pitch or variable-pitch), and the electric motors. For best performance and simplest
control algorithms, the motors and propellers should be placed equidistant. Recently,
carbon fiber composites have become popular due to their light weight and structural
stiffness. The electrical components needed to construct a working UAV are similar to
those needed for a modern RC helicopter, which include the electronic speed control
module, on-board computer or controller board, and battery.
Frame:
It is the structure that holds or houses all the components together. They are designed to be strong
and lightweight. To decide the appropriate frame for the copter 3 factors, i.e. weight, size and
materials used are considered. The frame should be rigid and able to minimize the vibrations from
the motors. It consists of 2-3 parts which are not necessarily of the same material:
Four motor brackets connecting the motors to the end of the arms
The main components used for construction of a UAV are the frame, propellers (either fixed-pitch
or variable-pitch), and the electric motors. [2] For best performance and simplest control
algorithms, the motors and propellers should be placed equidistant. Recently, carbon fiber
composites have become popular due to their light weight and structural stiffness. [2] The
electrical components needed to construct a working UAV are similar to those needed for a
modern RC helicopter, which include the electronic speed control module, on-board computer or
controller board, and battery.
9|Page
Frames are usually made of:
Carbon Fiber- Carbon fiber is the most rigid and vibration absorbent but it is the most
expensive too.
Aluminium- Hollow aluminium square rails are the most popular for the arms due to its
light weight, rigidness and affordability. [2] However aluminium can suffer from motor
vibrations, as the damping effect is not as good as carbon fiber. In cases of severe
vibration problem, it could mess up sensor readings.
Wood/ Plywood /MDF (Medium-density fibreboard)- Wood boards like MDF plates
could be used for the arms as they are better at absorbing the vibrations than aluminium.
[2] Unfortunately the wood is not a very rigid material and can break easily if the UAV
crashes.
For the center plate, plywood is most commonly used because of its light weight, easy
to work factor and good vibration absorbing features. [2] As for arm length, “motor-to-
motor distance” is sometimes used, meaning the distance between the
center of one motor to that of another motor of the same arm. [3] The motor to motor distance usually
depends on the diameter of the propellers in order to have enough space between the propellers
2) Rotors or Motors :
The purpose of motors is to spin the propellers. Brushless DC motors provide the necessary
thrust to propel the craft. Each rotor needs to be controlled separately by a speed controller.
They are a bit similar to normal DC motors in the way that coils and magnets are used to drive
the shaft. [2] Though the brushless motors do not have a brush on the shaft which takes care of
switching the power direction in the coils, and that‟s why they are called brushless. Instead
the brushless motor have three coils on the inner (center) of the motor, which is fixed to the
mounting. On the outer side, it contains a number of magnets mounted to a cylinder that is
attached to the rotating shaft. So the coils are fixed which means wires can go directly to them
and therefore there is no need for a brush. Brushless motors spin in much higher speed and use
less power at the same speed than DC motors. Also they don‟t lose power in the brush-transition
10 | P a g e
like the DC motors do, so it‟s more energy efficient. The Kv(kilovolts)-rating in a motor
indicates how many RPMs (Revolutions per minute) the
motor will do if provided with x-number of volts.
The higher the kV rating is, faster the motor spins at a constant voltage.
11 | P a g e
precise speeds to achieve accurate flight, the ESC is very important. This firmware in a
ESC changes the refresh rate of the ESC so the motors get many more instructions per
second from the ESC, thus have greater control over the UAV‟s behavior. The frequency
of the signals also vary a lot, but for a UAV it is preferred if the controller supports high
enough frequency signal, so the motor speed can be adjusted quick enough for optimal
stability
Propellers:
A UAV has four propellers, two “normal” propellers that spin counter- clockwise, and two
“pusher” propellers that spin clockwise to avoid body spinning. [3] By making the propeller
pairs spin in each direction, but also having opposite tilting, all of them will provide
lifting
thrust without spinning in the same
direction. This makes it possible for the copter
to stabilize the yaw rotation, which is the
rotation around itself.
12 | P a g e
Radio Transmitter and Receiver :
The radio transmitter and receiver allows to control the UAV. Four channels for a basic UAV
is required .Using a radio with 8 channels, so there is more flexibility is recommended. UAV
can be programmed and controlled in many different ways but the most common ones are by
RC transmitter in either Rate (acrobatic) or Stable mode. [2] The difference is the way the
controller board interprets the orientations feedback together with the RC transmitter
joysticks. In Rate mode only the Gyroscope values are used to control the UAV. The
joysticks on the RC transmitter are then used to control and set the desired rotation speed of
the 3 axes, though if the joysticks are released, it does not automatically balance again. [3]
This is useful when the UAV is required to do stunts like tilting it a bit to the right. The speed
of the 4 motors will be adjusted automatically and constantly to keep the UAV balanced.
Flight Controller:
The flight control board is regarded as the „brain‟ of the UAV. [2] It houses the sensors such
as the gyroscopes and accelerometers that determine how fast each of the UAV‟s motors spin.
Flight control boards range from simple to highly complex. An affordable, easy to set up,
having a strong functionality
The accelerometer measures acceleration and force, so downward gravity can be measured
too. It has 3 axis sensors, so the orientation can be worked upon also.
13 | P a g e
A gyroscope measures angular velocity or rotational speed around the three axis.
If accelerometer only is used then we can measure the orientation with reference to the
surface of earth. Sometimes the accelerometer can be very sensitive and unstable
because when the motor vibration is bad, the orientation is messed up. [2] Therefore a
gyroscope is used as a solution to this problem.
The gyroscope too drifts a lot. When the sensor rotates, the gyroscope will give the
angular velocity. But when it stops rotating, it doesn‟t necessarily go back to 0 deg/s.
The gyroscope readings will provide an orientation that continues to move slowly
(drifts) even when the sensor stops rotating. [3] Hence both the accelerator and the
gyroscope sensors have to be used together to obtain a productive orientation.
14 | P a g e
Advantages of UAV
The main merit of UAV and similar unmanned aerial vehicles is their small size, due to
which they could traverse in narrow conditions.
The use of drones has tremendously grown in a short span of time owing to the long flying
time in contrast to the manned aircrafts. [6] Without a human pilot, drones can operate for
significantly longer without fatigue than airplanes. Moreover, drone operators can easily
hand off controls of a drone without any operational downtime. They are remote controlled,
so no danger will be there to the crew.
They contain a whole lot of widespread applications, in day to day lives, domestic purposes
and national to international purposes.
Does not require mechanical linkages to change the pitch angle at the blade as it
spins.
Four small rotors have smaller diameter than one large helicopter rotor.
Takes less damage to rotors.
No need for a tail rotor which generates no lift.
Easier to build four small blades compared to large one.
Due to ease in construction and control, they are used in amateur model aircrafts
project.
They can traverse through difficult terrains because of their small size and there is
less risk of damage too.
They can save lives. [6] They greatly reduce putting military manpower in combat
They are significantly cheaper and the cost in fuel and maintenance is way lower than regular
airplanes.
UAV are smaller and are able to fly lower than traditional airplanes and the risk level to
military hardware is comparatively low.
Drones increase surveillance, reconnaissance, and general military intelligence.
15 | P a g e
UAV in agricultural use for
detecting lands for
appropriate plant growth
16 | P a g e
Disadvantages of UAV
Though drones possess a lot of advantages there are some concerns which should be thought about.
[6] They include:
1) Drones also contain limitations. For instance, they cannot communicate with civilians for more
detailed intelligence. Drones cannot capture surrendering military personnel, abandoned
hardware, or military bases. They cannot go from door to door (at least till now this facility is
not yet available). [6] Drone warfare causes collateral damages in civilian lives and property, as
well as traditional warfare too.
2) According to civilians drones are viewed as an invasion force. The mere presence of drones has
been known to convert civilians into military combats. Furthermore, when drones cause
collateral damage, such as killing civilians and damaging civilian property, the opinions of
civilians decrease even more so. [6] Additionally, some cultures believe the use of drones as
not brave and cold hearted. As a result, drones are sometimes counterproductive by more
destabilizing some regions.
3) Some drone pilots or operators have difficulty switching between combat mode at
work and civilian mode while not working.
This is especially difficulty when drone pilots have minimal transition periods between
work and personal.
4) The worst scenario is when drones or a fleet of drones have been commandeered or
taken control by the enemy. [6] While security measures help make this possibility
more difficult, it will never be impossible.
5) Exploitation of usage of drones could be done, for instance, spying (to the extent of
harming someone) that infringes privacy and confidentiality.
6) Battery power may be restricted and may require frequent charging.
7) Very limited funds coupled with ambitious design schedule. [6] Greater ambition
leads to more complex calculation and design.
But nevertheless, the advantages of UAV outweigh the disadvantages, and they are
worked upon so that optimum use of drones could be implied.
17 | P a g e
Discussions
UAV or drones first came to application as small toys, or school/university projects and then
no sooner began to garner widespread attention- used in big-budget movies, photography of
high profile sports, agricultural use to rectify lands and detect levels of pesticides as well as
other components like nitrogen in plants, search and rescue, land mapping, military.etc. The
commercial as well as private use of drones is enlarging.
The main point is that with growing progress in technology, drones too are coming in
different shapes, sizes and configuration (UAV, hexacopters, etc.) for better load and yaw
stability. Moreover, extended components like camera, water- resistant components or GPS
tracker make it easy in missions of combating, surveillance and especially search and rescue.
After 10 years, the market for commercial drones will reach $1.7 billion. Each year, $6.4
billion is being spent developing drone technology. The drones are even providing new job
opportunities. 70,000 new drone-related jobs are projected within the next three years in USA
alone. 100,000 new jobs are expected till 10 years. Moreover, schools are offering drone
degrees & programs in order to provide a trained workforce capable of meeting this demand.
This may also prove that there is no need for people to fear about losing their jobs because of
replacement by robots or drones.
But there are also some concerns like all the new leading technologies. It is important to plan
appropriately to achieve a productive outcome. Privacy among being the major concern in
warfares, could be used as a means of spying which is mere exploitation and negative use of
UAV technology.
Since the advantages of UAV technology are more than its demerits (are very well
rectifiable), then according to drone experts, drones will be “in trend” within next 10 to 20
years.
There is a wide scope that with its extending use in almost every field and with greater
powerful components, drones will surely come into full time existence.
Hence UAV will very soon start taking over larger roles in a variety of jobs.
18 | P a g e
Indian UAVS:
DRDO AURA is a stealthy unmanned combat air vehicle
DRDO Nishant
DRDO Netra
DRDO Rustom
Lakshya PTA
Ulka
Fluffy
Pawan UAV
Kapothaka
19 | P a g e
Conclusion
Drones will soon take on be an imperative existence in the coming future. They will be
seen taking up larger roles for a variety of jobs including business in the immediate future
They could become a part of our daily lives, from smallest details like delivering groceries
to changing the way farmers manage their crops to revolutionizing private security, or
maybe even aerial advertising. Today, UAV are capturing news video, recording vacation
travel logs, filming movies, providing disaster relief, surveying real estate and delivering
packages.
They are categorized according to their corresponding uses. Some are for military
purposes provided with missiles and bombs, some for surveillance and reconnaissance
purposes.
Agriculture is predicted to be the dominant market for UAV operations. In Japan drones
are flown for the past 20 years. Lot of the farmlands over there are on steep hillsides, and
those vehicles can treat an acre in five minutes which is very difficult or even impossible to
do so with a tractor.
The innumerable advantages of drones lead to their growth in a short span of time. They
have a few demerits but those can be rectified. Today most drones are controlled by either
softwares or other computer programs. The components of a drone also vary based on what
type of work needs to be done and how much payload needs to be carried. Outrunners,
batteries, electronic speed controllers all come in different ranges according to the type of
work needed to be done by the UAV.
UAV are a great provisional craft that could get in between airplanes and helicopters and
are hence easier to fly all the time. Beside realtime 3Dflight, such as inverted flight, UAV
give a more acrobatic feel to its flyers. UAV offers to be a great balance between cost ,
capability, and performance. The only problem is when funds are coupled with highly
ambitious projects. A solution for this could be to gradually improvise on inventing UAV
with new enhancements and new designs. Hence UAV have an exemplarily bright future.
The onus lies upon us whether we productively use it or destructively use it.
20 | P a g e