Professional Documents
Culture Documents
Depots Guidelines 2009
Depots Guidelines 2009
ISSUED BY
CLASS A Petroleum products liquids which have flash point below 210C (730 F)
e.g PMS
CLASS B Liquids which have a flash point from 210C (730 F) to 550 C (1500 F)
inclusive (e.g. DPK, HHK, ATK)
CLASS C Liquids which have a flash point above 550 C (1500 F) up to and
including 1000 C (2730 F) e.g. AGO.
RESTRICTED AREA The area within the boundaries of all depots, installations or jetties where
management exercises control over movements and operations.
HAZARDOUS AREA Within the restricted area specific sections are designated hazardous
because the atmosphere may be explosive (flammable).
IGNITION SOURCE Any source that supplies sufficient energy to ignite a flammable
atmosphere
2
TABLE OF CONTENTS
INTRODUCTION
PART ONE
PART TWO
2.1 Conditions Governing the Engineering Design of a Petroleum Product Depot.
2.1.1 Depot Configuration.
2.1.2 Project Execution Strategy/Quality
2.1.3 Process Safety Consideration/Ultilitis Provision.
2.1.4 Project Presentation
2.1.5 Grant of Approval to Construct (ATC)
2.1.6 Conditions Governing the Construction of a depot
2.1.7 Environmental and Safey Considerations
2.1.8 Approval to Commission.
2.5.5 Maintenance
PART THREE
3
3.12 Floating Roof tanks………………………………………………………21
3.13 Pumps
3.14 General Facilities
3.15 Quality Control…………………………………………………………..22
PART FOUR
PART FIVE
PART SIX
4
PART ONE
INTRODUCTION
1. Petroleum Products are stored in bulk in strategic depots scattered over the country. These facilities
which are provided for storing large volumes of liquids and gases can be classified as closed-storage
vessels or open-storage vessels. Closed-storage vessels include fixed roof tanks, pressure tanks,
floating roof tanks, and conservation tanks while open-storage vessels include open tanks, reservoirs,
2. In view of the volatile nature of hydrocarbon and gases stored in these facilities, it is imperative to
formulate guidelines and standards necessary for their proper handling and control.
In Nigeria petroleum industry, the control regulations for the construction and operation of depot
facilities are governed by the principal legislation of the Petroleum Act 1969. The regulations are made
pursuant to Section 9 e (v) & (vii) of the Petroleum Act 1969 Cap 350, No 51 which empowers the
Minister of Petroleum Resources to make regulation for the bulk supply, storage and distribution of
petroleum products. Some of the specific regulations include the Mineral Oils (Safety) Act 1963;
Petroleum Regulation 1967 Cap 350 Section 37; Oil Pipeline Act 1965; the Oil in Navigable Waters
Regulations 1968; Petroleum Refining Regulations 1974; Petroleum (Amendment) Regulations 1988;
Mineral Oils (Safety) Regulation 1997; and the Environmental Guidelines and Standards for the
5
PROCEDURE AND CONDITIONS TO BE FULFILLED BEFORE
THE GRANT OF APPROVAL TO CONSTRUCT/MODIFY
PETROLEUM PRODUCTS DEPOT
Pursuant to the provisions of the Petroleum (Amendment) regulations 1988, all applications
for approval to construct/modify construct or license a depot shall be addressed to the
Director, Department of Petroleum Resources office, situated at 7 Kofo Abayomi Street
Victoria Island, Lagos: to be accompanied with the following documents as applicable:.
a) A master plan drawn to scale, showing the site of the installation and the design of the storage
shed, tanks and facilities in all respect in sufficient details and any other relevant information
that may enable the project to be fully understood.
b) The description and quantity of petroleum products which the applicant desires to store and the
manner in which it will be stored, whether by surface or underground storage arrangements.
c) The name and location of the proposed depot, the location shall fulfill the provisions of sections
36 and 39 of the Petroleum Regulations of 1967 as applicable to the installation.
d) Codes, Standards and Specifications to be adopted in the design of the plant with specifications
of equipment and facilities to be installed.
e) Detailed description of laboratory facilities and equipment to be used for products quality
control and test methods to be used.
f) The parcel of land will not be less than (5) Five Hectares of land to allow for free flow of
traffic.
g) Service provisions such as good roads, electricity, water etc should have been provided ab –
initio
h) Truck Holding Bay: A reinforce concrete cement to atleast hold fifty trucks at a time shall be
mandatory
6
ACCOMPANYING DOCUMENTS
The following documents must accompany every application for approval to construct or
modify a hydrocarbon depot
1.3 Copies of the depot plan showing the existing or proposed building on the site and
relation of the site to roadways, water ways, rail roads, electrical distribution and Oil
Pipeline right of way and adjoining property.
1.4 Copies of equipment layout including all Piping & Instrumentation drawings
(P&IDs) of the proposed depot or modifications. A COREN registered engineer must
stamp all these drawings.
1.5 Copies of Fire Service report indicating that the proposed arrangements for
prevention of fire and containment of emergencies are satisfactory.
1.6 Copies of Police Report indicating that the proposed site and operations of the depot
will not constitute any traffic problems.
1.7 Copies of letter of consent and approval from the Town Planning Authority. The Town
Planning Authority stamps on all the Depot project buildings drawings are acceptable.
1.1.1 Copies of tax receipt or tax clearance certificate for the proceeding three years. A tax
exemption certificate issued to a newly incorporated company is acceptable.
1.1.3 Detailed Safety Case proposals for the depot project and shall be reviewed every 3
years
1.1.5 A certified cheque or bank draft of the stipulated non-refundable application Fees of
One hundred and fifty thousands Naira (N150,000.00) only made payable to Federal
Government of Nigeria - DPR Fees Account, Depot licenses shall be renewed every
year after due safety diligence inspection of the facility (Appendix 3, 4, & 5). Renewal
shall be subjected to same amount. All applications shall also has a DPR service charge
of Five hundred thousands Naira (N500,000.00) made payable to Department of
Petroleum Resources
1.1.6 Comprehensive reasons for the proposed depot modifications where applicable.
7
1.1.7 Possession of the requisite and relevant documents of approval from stakeholders
agencies e.g Nigeria Port Authority, NIWA for the construction of a jetty and
petroleum storage facility along the water way
Documents listed in 1.1 – 1.14 above shall be submitted in triplicates (original and two copies) as a
pre-condition for grant of “Approval to Construct” (ATC)
a) It shall be the responsibility of the DPR to ensure that all the above listed documents in section
2(ii) have been submitted.
b) A delegated officer of the DPR shall diligently review the submissions for completeness and
acceptability.
Such officer must ensure that relevant divisions of the Department have opportunity of
assessing the project (with their comments and or approvals collated) before conclusions can be
drawn on the project.
The delegated officer shall undertake a site inspection of the proposed location of the depot and
relate his findings to the engineering, safety and environmental submissions.
The assessment shall disallow the use and installation of obsolete technology and equipment in
the proposed depot.
c) The DPR shall formally invite the applicant for a presentation of the project work program as
soon as section 2 (iii) b above is satisfactory.
e) The Director, Department of Petroleum Resources, shall subsequently upon (d) above, grant
the approval to construct the depot to the applicant in writing.
f) The DPR shall simultaneously appoint a team of competent engineers and technicians who
will ensure compliance with international and national standards in equipment acquisition,
construction and entire facilities integrity.
8
1.3.1 DOCUMENTS/CONDITIONS REQUIRED FOR TRANSFER (TAKE-OVER) OF
DEPOTS
(n) Truck Holding Bay: A reinforce concrete cement to atleast hold fifty trucks at a time.
9
1.3.2 PETROLEUM DEPOT EQUIPMENT: INSTALLATION, MODIFICATIONS,
EXPANSION AND MAINTENANCE
a) The depot manager shall expressly inform the Director, Department of Petroleum Resources
or any officer delegated by him, of any equipment acquisition, installation, modification /
expansion of facilities giving sufficient notice and details for approval.
b) Modifications and expansion works shall be given equal attention like fresh projects in the
areas of engineering, safety and environmental concerns.
c) All pipeline and equipment breakdowns that affect normal depot operations shall be reported
immediately to the DPR representative along with the maintenance program which should be
received not later than 24hrs after such reports.
d) Every equipment replacements must be such that the design standard of the defective one is
not compromised.
e) Strategic equipment list and a two – year stock of maintenance spare parts or replacements
shall be kept at each depot.
f) It shall be the duty of the depot manager to adhere strictly to the maintenance instructions of
the depot equipment manufacturers.
g) Routine inspection of all equipment and pipeline shall be undertaken at every depot. Critical
laboratory equipment shall be tested / evaluated weekly for quality assurance. The manager
shall maintain a record and report of such inspection and shall make the documents available
to the DPR officials on demand.
h) The DPR shall be free to ask and obtain operational information and record from petroleum
depots unhindered.
i) Hoarding of operational information is to be treated as a breach of the license to operate a
petroleum depot which attracts a six calendar months suspension of operating license.
a) It shall be the duty of any individual or organization willing to operate a petroleum depot to
formally apply for approval to construct the depot from the Director, Department of Petroleum
Resources.
b) It shall be an offence for anyone to construct a petroleum depot without an approval of the
Director, Petroleum Resources. Offenders shall l have to
1. Pay a fine of Twenty Million Naira (N20,000,000:00) only before the application can be
considered and
2. Pay the stipulated non refundable fee for approval to construct a depot.
c) All licensed and operating depots are to apply and secure approval for all forms of
modifications, expansions, replacements and reconstructions within the licensed depot before
10
commencement of works. Any violation of this provision will attract a fine of Twenty Million
Naira (N20,000,000:00) only.
c) It shall be an offence to operate a petroleum depot without a written approval of the Director,
Department of Petroleum Resources. Contravention of this provision will attract a fine of
Twenty million (N20,000,000:00) naira only.
d) A depot constructed without a DPR approval shall have to pay additional fine of Twenty
Million Naira (N 20,000,000:00) naira only.
e) All the fines are exclusive of the stipulated application fee for approval to operate a petroleum
depot
a) It shall be the duty of the depot manager to formally apply to the Director, Department of
Petroleum Resources for a depot operating license after completion of construction works on a
petroleum depot for which approval to construct had earlier been granted.
b) The depot manager shall continue to apply for license renewal annually or as required from
time to time.
c) A petroleum depot without a valid current license shall not be allowed to operate until a valid
license is secured from the Director, Department of Petroleum Resources.
d) The depot manager shall submit copies of the manufacturer data and maintenance book for all
critical equipment.
e) The stock list of three years maintenance spares for all strategic equipment must be verified by
physical inspection in the warehouse as a condition for licensing a petroleum depot.
f) A list of competent and trained personnel for the depot operation and maintenance should be
made available to the DPR. The Department shall arrange to verify the competence of the
listed individuals as it deems fit before they can be cleared to work in petroleum depot. The
competence of these individuals shall cover expertise / skill in their job function as well as
safety.
i. Leak test for above the ground storage tanks (AST). Compulsory for all new tanks, to
be repeated at the tank age of five (5) and from 10years the exercise shall be repeated
every two years.
ii. Calibration of tanks
11
iii. Meter Proving
iv. Vacuum box test.
h) Appropriate safety and warning signs (“No Smoking”, “Unauthorized Person not Allowed”,
“Restricted Area”, “No Matches Allowed”, “All Vehicle Exhaust Pipe must be fitted with
Spark Arrestor” etc) must be displayed at the entrance to the facility and within the depot
installation.
i) The foregoing notwithstanding, all the provisions of Petroleum Act (Cap 150), Petroleum
Regulations 1967, must be satisfied before the depot could be considered for licensing. Then
filled Appendix 2
j) License / Approval to operate a petroleum depot facility will be granted by the Director,
Petroleum Resources or person assigned by him if the constructed depot fulfills all the
stipulated statutory requirements and has been inspected and recommended for an operating
license by scheduled officials of the Department.
12
PART TWO
SECTION I
i) Final depot configuration including detailed Piping and Instrumentation Diagram (P&ID)
of the various units, utilities and offsite facilities.
Every applicant for approval to construct a depot shall make a technical presentation of the entire project to DPR
and shall be required to submit
13
i) The names of prospective fabrication and construction contractors and the fabrication
program.
ii) The yard in which all vessels, columns and ancillary equipment would be fabricated.
iii) Arrangements for statutory monitoring of the various stages of equipment fabrications by
officials of DPR.
SECTION II
i) Submit the detailed engineering of the depot to the Department of Petroleum Resources
as specified in section 2.4 of these guidelines for review and approval.
ii) Make a comprehensive presentation on the project design to DPR
Having satisfied the requirements in section 2.1 (i & ii) above, the Honorable Minister may grant
the applicant the construction license upon recommendation from the DPR.
The applicant can subsequently proceed with the Procurement and Construction phase of the
project.
i) The depot owner shall provide the Department of Petroleum Resources with the following
information for necessary reviews and approval before the commencement of fabrication:
a). The name and job references of the company appointed as quality control inspectors
and Curriculum Vitae (CV) of its principal technical staff.
b). All fabrication and welding procedures.
These procedures shall generally follow the relevant specifications in the under-listed
documents:
1. American Welding Society – Structural Welding Code A.W.S.D.1.1 88 and the
subsequent revisions.
2. API Standards 1104 – 17th and subsequent editions for welding of pipelines and related
facilities.
ii) At the completion of fabrication, the quality control inspecting company shall compile a
report confirming that all materials used were strictly in accordance with approved
specifications as verified through steel mill certificates with the approved Standards and
Codes of Practice. The quality control inspection shall be by Non-Destructive Examination
14
(NDE). Consequently, inspection and certification of all welded parts of vessels, columns
and piping shall be by any of the following techniques as applicable viz.:
iii)
a). Liquid Penetrant Technique
b). Magnetic Particle Technique
c). Radiographic Technique
d). Ultrasonic Technique
A comprehensive report of the inspection so carried out shall be forwarded to the
Department through the depot owner.
These shall include all available meteorological parameters, such as the prevailing wind
direction, maximum wind velocity, maximum and minimum atmospheric temperature, relative
humidity, rainfall, local flood or tide conditions.
a) All environmental parameters shall be obtained from independent site survey with all
the data gathered being properly documented.
b) Soil test and geo-technical investigations shall be carried out for foundation or load-
carrying characteristics of the site.
c) Contour maps (site plan), showing ground elevations shall be prepared
d) Effect of borehole water withdrawal on ground water table shall be investigated and
result submitted.
a) There shall be a detailed Environmental Impact Assessment (EIA) study of the area as
provided for in the National Environmental Guidelines and Standards for the Petroleum
Industries in Nigeria (EGASPIN) as issued by the DPR before commencement of
construction.
b) The general layout of the location and provisions for all waste disposal in the depot
shall comply with the applicable specifications in the EGASPIN
c) The depot shall be equipped with adequate provisions for containing and handling spills
and accidental discharge of potential contaminants.
d) All the systems and components of the depot shall be designed to withstand any
anticipated extremes of environmental phenomena on location.
e) The provision of effluent and recipient water quality monitoring shall be in accordance
with the EGASPIN
15
2.5.3 SAFETY FACTORS
a) All offices, warehouses and process buildings shall be constructed with utmost
consideration for the safety of the workers and equipment. Laboratory building
construction shall take into consideration the safety of personnel and provision of
adequate ventilation as well as that for proper disposal of waste.
b) Material Safety Sheet (MSS) shall be prepared in respect of all potentially hazardous
chemicals and materials.
c) Emergency alarm system and evacuation programs shall conform to Standards Industry
Practice to the satisfaction of the Honorable Minister.
d) Fire sensors and gas detection and alarm system shall be installed at strategic points of
the depot and its offsite facilities. In addition, adequate fire mitigation systems shall be
provided at all identified fire risk areas of the depot.
SECTION III
1) A qualified depot manager is appointed and his appointment is notified in writing to the
Minister of Petroleum Resources.
2) Completion of all fiscalization equipment and systems to approved standards.
3) Availability of adequate spare parts and other operating consumable materials in the
warehouse appropriately codified and organized.
4) Availability of commissioning spare parts, apart from operating spare parts, all properly
coded and arranged in the warehouse.
5) Approved operating manuals, maintenance manuals, mechanical catalogues, would have
all been supplied, subject to appropriate modifications after commissioning.
6) Approved operating and maintenance organization and availability of trained manpower
in sufficient strength.
7) Functional and effective fire prevention and fighting organization already in existence.
8) Functional and effective Safety enforcement Organization and Policies already in
existence.
9) All approved engineering drawings in agreed numbers of copies have been supplied by
the contractor, subject to modifications to reflect changes during construction.
10) The quality control laboratory is completed and functional.
11) A well-staffed and equipped First Aid Administration is in place.
12) All other provisions, which are reasonably required to facilitate effective commissioning
of the depot, have been made.
13) An effective and international applicable materials codification and management system
is in place.
14) Confirmation that all-environmental protection standards and during design have been
met.
16
2.5.5 MAINTENANCE
b) The depot facilities shall be periodically examined for corrosion detection and corrosion
protection systems and devices installed shall be checked regularly to ensure effective
performance. All these anti-corrosion performance monitoring shall be carried out in
accordance with current NACE (National Association of Corrosion Engineers) Standards
and procedures.
APPENDIX II
DESIGN CONSIDERATIONS
The design parameters shall generally follow but not limited to the specifications outlined in the
current editions of:
17
PART THREE
The operation of depots and installations demand diligence to avoid spills, explosions and fire. This
implies among others that a competent person must always be available during all the operations
particularly during the discharge or loading at the installations or depots. Furthermore, frequent
observations should be made on ship-to-shore connections and pressure gauges. Appropriate warning
signs must be displayed where necessary. Highlights of the key activities in the operations of depots
and installations include:
a) All custody transfer meters at petroleum depots shall be calibrated once a month in the
presence of the DPR representative.
b) It shall be the duty of the depot manager to ensure that all meters used for pipeline transfers
and tanker loadings are proved in line with (a) above.
c) Every functional custody transfer or loading meter that undergoes maintenance in between the
stipulated meter proving cycle shall be re-calibrated and proved after the maintenance
exercise.
d) The DPR resident officer at the depot shall program the monthly meter proving exercise and
inform the depot manager who shall in turn comply.
e) It shall be an offence for any depot manager to operate with a defective or unproved meter.
The offence attracts the immediate suspension of such manager and sealing up of the relevant
loading arms at the depot.
f) All existing meter proving procedures shall be complied with in line with good oil field
practices.
18
3.3 SAFETY AT PETROLEUM DEPOTS
a) A security wall or fence of not less than 3m high shall normally surround all installations
and/or depots to prevent the entry of all unauthorized persons.
b) Safe distances must be maintained for positioning of storage tanks, product reception and
loading facilities in a depot to ensure safety and effective control in case of spillages,
accidents and other emergences.
i) Petroleum Storage tanks should be placed such that any hydrocarbon vapor will have
diffused into the atmosphere to a concentration well below the lower flammable limit
before reaching any area which may be designated as hazardous.
ii) The layout of the tanks should take cognizance of accessibility for fire fighting.
iii) Tables 1 to 3 below present standard design layout guidelines for storage tanks
classification (I, II, and III) at petroleum depots or installations.
CLASSIFICATION DEFINITION:
CLASS „I‟ Fixed roof above ground tanks storing classes A, B and C
petroleum products at installations
CLASS „II‟ Floating roof tanks storing classes A and B petroleum products at
installations and
19
TABLE 1
FACTOR RECOMMENDED
DISTANCES
Between a group of small tanks and any tank outside the 15m
group.
Between tanks not being part of small tanks. 15m < ½ (DL + DS) > 10m.
Between a tank and any filling point, filling shed or building. 15m
INDEX:
20
FIXED ROOF ABOVE GROUND TANKS STORING CLASS I, II (2) AND III (2)
PETROLEUM
TABLE 2.0
LOCATION AND SPACING FOR FLOATING ROOF TANKS STORING CLASS I AND II (2)
PETROLEUM INSTALLATION
Between a floating roof tank and a fixed roof tank. 15m. < ½ DL >10m.
TABLE 3.0
a) Tank Compound-
The net capacity of a tank compound formed within the main bundwall, or the net capacity
of a suitable depression should be 110% of the capacity of the largest tank in the case of
class I and II storage tanks.
If the leakage or spillage is anticipated in class II and class III petroleum products storage,
that could cause damage to third party property, drainage systems, rivers or waterways, a
low bundwall should be constructed around the tank age.
The roadways and packing areas should be such that the main roads are suitably surfaced
and drained. Those carrying traffic in two directions should not be less than 6m wide and
single traffic lines should not be less than 4m wide.
21
A separate parking area shall be provided for petroleum tankers in order that road-ways
and loading areas should not be used for parking. It is advantageous if car park can be
constructed outside the main security fence of the installations or depot
Road near loading or unloading facilities for class I or class II (2) petroleum should be at a
safe distance from boundary. This distance should normally be at least 15m but in small
depots, it may be reduced to 10m.
c) Power House
The location of the boiler house, power plant and fire pump house should be located in
non-hazardous areas and where the equipment can be safely operated in the event of a fire
or spillage
d) Environmental Control
Provision should be made for drainage channels from the tank drain valves. These drainage
channels should run to one or more oil interceptor should be cited away from the
boundaries and hazardous areas and within easy access for inspection, cleaning and
maintenance.
Adequate lighting should be provided for night operations. This should enhance safety of
personnel and provide for operations to be carried out in a safe manner for the maintenance
of security.
e) Pumps
These are generally grouped together in one area or individual sited to suit operational and
constructional convenience.
They should preferably be installed above ground level and in the open air outside the tank
compound except severe climatic conditions are experienced.
Pump for class I or II (2) petroleum should be located not less than 15m from the boundary
but in the case of small depots, this distance may be reduced to 10m.
Pumps driven by gasoline and diesel engine shall not be operated in a hazardous area.
Diesel engines should be installed above ground level to avoid their operation in an
accumulation of flammable vapor. There should be a means of rapid shutdown of the unit
in event of emergency.
3.5 Bulk Road And Rail Vehicle Loading and Unloading Facilities
Over-filling, splash loading and free fall of product shall be avoided during loading
operations.
22
The layout of road loading or unloading facilities should incorporate ease of tank vehicle
access and exit without the need for reversing.
Suitable barriers which may include clamps, locks or other means of control shall be
employed to prevent unauthorized train movement, or access by locomotives while rail
tank cars are still connected to the loading or unloading facilities.
Efficient catches shall be employed to hold railway line gates open when required.
Materials used in the construction of the loading and unloading structures shall be non-
combustible. Boundaries should consist of an approved form of secure fence. It could be of
chain link fencing, steel paling, brick, mass concrete or post and slap concrete
construction.
a) All ship‟s personnel using shore facilities for cooking, resting or recreating should be well
versed with relevant depot and installation regulations regarding smoking or the use of
naked lights.
d) The installation / depot Manager or his representative should discuss and agree with officer
in charge of the ship, the sequence of operations, maximum pumping rates and pressure for
each product, and a signal system for discharging or loading control including emergency
stoppage.
e) If the vessels carry class A and other classes of petroleum products, flash points should be
checked to ensure that no cross contamination is occurring.
f) All necessary precautions shall be taken to avoid spillages into waterways and in addition,
floating booms should be provided.
g) Valves should be checked to ensure that they are in good working order.
h) The operator in charge of the flexible ship-to-shore connections and other discharge
equipment should constantly check the pressure gauges and in event of excessive rise in
pressure, arrange for pumping operations to be stopped immediately until the cause is
identified and duly rectified.
23
i) Operational facilities that protect man and equipment against static electricity, lighting and
electric current shall be provided.
Safety precautions while loading and unloading rail tanks cars include:
a) No major repairs should be permitted while loading and unloading rail cars.
b) Loading and unloading arms or hoses should be properly stowed after use.
c) Loading and unloading arms, hoses and connections must be clearly identified, by
either color-coding or nameplates, to indicate the grade of product for which they
are applicable.
e) In case of fire outbreak, the supply of product cut-off and effort must be
concentrated to contain/put off the fire. In addition to that, the nearest area office of
the fire fighting authority and DPR must be notified. Operations will be allowed
after thorough investigation by DPR and other relevant government agency.
Commencement of operation shall be permitted when adequate measures have been
put in place to prevent similar and foreseeable fire outbreak in the depot or
installation.
It is necessary to establish prior to gauging and sampling product, clear procedure for receipt of
products into the storage tanks at depots and installations. We should ensure that each tank is
clearly marked with tank numbers:
(b) Dip hatches for manual gauging of tanks storing class I or II (2) petroleum should be
opened as when necessary, consistent with obtaining tank gauging for control of
inventory and tank filling.
24
(c) If a tank is filled with more than one dip hatch, only one should be opened at a time.
The dip hatches should be closed when not operational.
(d) When atmospheric conditions (electric storm, hail, flying sand) create risk of static or
other hazards, manual gauging should be stopped.
(e) A minimum of 30 minutes should elapse between the commencement of gauging and
the end of tank filling operations for class I, II and III petroleum.
(f) In the case of floating roof tanks, a gauging well, which is normally at the top of
access, stair way should be used. This eliminates the need to descend on to the roof.
(g) Automatic gauging equipment should be checked against manual dips at periodic
intervals. A check on the fitting provided in floating gauges is recommended. This
will ensure that the float is on the surface.
Water could be introduced into a tank from a ship or if a water plug clears pipeline. Water
bottoms in tank cause internal corrosion of tank bottom and lower shell plates. Water should be
removed as soon as possible after the tank contents have settled. Water drawn off from tanks
should be passed through an interceptor before passing to any external drainage system.
The roof of a floating roof tanks should be examined frequently to ensure that they are floating
evenly and not sticking. This is highly recommended during heavy rains or in freezing water.
Valves on drains should be closed when the operation is completed, to prevent loss of product
in the event of failure of the internal drain line. It is also recommended to ensure that the inlet
velocity (until the inlet of the tank is completely submerged, and until the pipeline is free of any
water or air) should not exceed 1mn. per second. This would avoid the build-up of static
charges when filling a tank with classes II, III petroleum static accumulator products or I. This
may create a flammable atmosphere in the tank ullage space by vaporization or formation of
the mist.
To ensure proper drainage of tank enclosures, normal gravity drainage could be applied or
alternatively by means of manually controlled pump, or by siphon drain. Furthermore, water
from tank enclosures should pass through an oil interceptor before passing to any outside
drainage system or watercourse. A valve by-pass round the interceptor would provide for
controlling flow of uncontaminated water in exceptional storm conditions or the release of fire
fighting water.
25
3.9.4 PUMPS
All pumps should be inspected regularly particularly for abnormal noise, signs of over-heating,
gland leakage, alignment and general condition. In the case of power driven pump, the motor
and control gear tested for continuity, earthling and insulation resistance. All positive
displacement pumps should have a by- pass relief valve.
In all operations, pumps should not be left to run against a closed delivery valve, as it would
cause churning, over-heating of pump and product.
In all depots and installations, support facilities like boilers compressed air, oil interceptors are
provided. Good oilfield practice recommends a effective means of handling each structure in a
depot such as:
(a) Boilers- The basic safety procedure for running boilers is similar and it should be
complied with regardless of the boiler being automatic or manual type. The operators
should understand the reason for each specific inspection. Water gauges should be
tested and blown down at least twice per shift to ensure that they are working
correctly. Low and High-level alarms and flame failure protection should be tested
weekly, unless a continuous blow down system is installed, the frequency of blowing
down of the boiler should be in accordance with the prescribed boiler water control
procedure.
(b) Compressed Air. - Air receives which are in constant use should be drained of water
daily, or an automatic water drain installed. Failure to ensure adequate drainage of
water would lead to corrosion of the air receiver.
(c) Oil Interceptors- All oil interceptors should be regularly inspected and routinely
cleaned. If oil and dirt are allowed to accumulate in the oil interceptor unattended, the
oil interceptor looses its effectiveness.
26
Vapour Pressure
Sulphur
Lead
Research Octane Number (RON)
Existence Gum Tester
Pour Point Tester
Fridge
Freezers
Sampling bottles (Glass & Plastics)
It shall be an offence to discharge off-Spec Petroleum Product into a licensed storage facility or
diversion of such product to unknown location
Contravention of this provision will attract a fine of Twenty million Naira (N20,000,000.00) or
5% of the cost and freight of the product.
27
PART FOUR
4.0 GUIDELINES FOR PETROLEUM PRODUCTS TRANSFERS AT DEPOTS/JETTIES
a) Transfer of Hydrocarbons
1. The transfer of any petroleum products from one petroleum depot/Jetty to another or
from a refinery to a depot/jetty shall be done only with the consent and approval of the
Director, Department of Petroleum Resources or any officer delegated by him.
2. It shall be the duty of the depot manager of the depot to expressly inform the Director,
(or his delegated officer), of his program to transfer petroleum product from his depot to
an identified duly licensed depot by completing the product transfer format.
4. The resident DPR Officer shall inform the receiving depot of the commencement date
and time of the petroleum products transfer and the expected arrival date and time.
5. It shall be an offence for any depot to open a transfer valve without an officer of the
DPR. The offence shall be punishable by suspension of depot license of the offender for
one (1) calendar year or a fine of One Million Naira (1,000,000.00)
28
4.1 Reception at the Destination Depot:
a) All petroleum depots shall install pipeline inter phase monitors on their inter depot pipeline for
the purpose of monitoring products quality before arrival at the products reception area (PRA).
b) Off-specification products shall be pumped to appropriate slop tanks. The expected inter phase
for downstream transfers is either AGO / DPK or PMS / AGO. Hence each depot is to
maintain a tank for each class of inter phase.
c) The depot manager shall on daily basis take composite sample of the slop tanks, conduct
laboratory analysis of the sample and make the result available to the resident DPR officer.
The sampling and shall be in the presence of a DPR official.
d) The depot manager shall not transfer, utilize, sell, blend or take any portion of the content of
these tanks without a satisfactory application and express approval of the Director, Department
of Petroleum Resources or his delegated officer.
e) The inlet valve into the nominated reception tank shall be opened only by consent and express
approval of the DPR resident official.
a) All the requirements of section 3.1.1(a) of this guideline shall be met satisfactorily for intra
depot tank-to-tank petroleum products transfer.
b) There shall be products quality compatibility established by the depot manager and witnessed /
confirmed by the resident DPR officer at a depot before a tank-to-tank transfer can take place.
Moreover, the source tank shall not be made to pump below 105% of its dead stock while the
receiving tank should not attain a level above the calibrated safe maximum.
c) The content of the service pipeline in quantity, quality and type shall be such that
contamination or adulteration shall not occur during or after the transfer.
d) The initial and final readings of the on-line meter shall be documented for products
accountability.
29
e) Products quality analysis shall be performed on the active storage tanks before and after the
operations. The results and samples shall be kept in the depot to the knowledge of the resident
DPR officer until 14 days after the content of the receiving tank has been distributed for public
consumption.
f) Contents of slop tanks shall normally be pumped back to the nearest refinery for further
processing
a) On no account should a tank under intra-or inter-depot transfers be nominated for public
distribution same day without carrying the requisite quality certification.
b) The following preparatory information must be ready in a depot before a petroleum storage
tank is nominated for loading:
A list of all requests to load a brand of petroleum product and a summary of the
requests.
The quantity / quality record of all tanks containing the requested product.
c) It shall be the duty of the depot manager to select a storage tank and an alternative, where there
are more than one tank containing the same product in the depot, that can accommodate the
total requested volume of the product; such tank must be containing on-spec product.
d) The above shall be done, at close of work, on a day before the loading date.
e) On the loading date, the tank shall be re fiscalised and sampled at 6:00 AM in the presence of a
DPR inspector who shall also witness the calculations and laboratory analysis. The results
obtained shall be used to confirm previous tank nominations if consistent.
f) In the event of contradictions, the consistent alternative storage tank shall be nominated.
g) In the event that there is no consistent tank,
1. The loading/lifting of the reference product shall be deferred to the next day to allow for
proper tank nomination if the failing parameter is the product quality. The deferment shall
immediately be communicated to the DPR resident officer and thereafter to the costumers.
2. The tank fiscalisation shall be repeated and if the difference between the final stock of the
previous day and that of the loading day is such that physical environmental conditions can
justify, and there is perfect repeatability of the tank quantity on the loading date, the new
quantity shall be upheld and the petroleum product tank can be confirmed by the DPR for
loading on that day.
a) There shall be no transfer of any petroleum product to loading arms in a depot except the tank
has been nominated for loading in line with provisions of section 3.1.3 above.
30
b) It shall be the duty of the depot manager to indicate the specific loading bay and relevant arm
that a nominated tank shall supply on the loading day. He shall make the program available to
the resident DPR official along with the loading arm meter number, its last date of calibration,
meter tolerance, and the initial meter reading.
c) The DPR inspector shall crosscheck this information before commencement of loading. He
shall also record the functional state of the loading arms.
d) The DPR shall refuse the transfer of petroleum product to a loading arm if
1. The tank was not properly nominated in line with section 3.1.3 a above
2. The tank level gauge / side glass is faulty
3. The loading pump has leakage or outstanding maintenance that may cause a total
breakdown / fire during operation
4. The arm meters have not been calibrated or proved for upwards of one month
5. The meters were proved and the tolerance is greater than +2% or if there was no consistent
repeatability.
6. The meter proving frequency exceed twice in a month after correction of some faults or
maintenance.
7. The arms and elbows are leaking petroleum product
8. The loading arm bay has no earthen clamps or if the clamps are defective.
9. The arm is not being manned by a competent loader.
10. The time is before 0800hrs or after 1530hrs on a working day (Monday to Friday) and if the
loading date falls on a Sunday.
Saturday loading shall be between 0800hrs and 1200 noon. Exceptions to this timing shall
be as approved by the Director, DPR or any officer so delegated and the depot manager
shall apply for it in emergency situations.
11. The pipeline line from the nominated tank to the loading arm contains a product that is not
the same as the tank content
12. There is pipeline or on-line valve leakage between the tank and the loading arm
13. There is insufficient hazard protection at the loading bay
e) As soon as a tank to loading arm transfer of a petroleum product is approved, the tank initial
level and hence the volume is recorded, the main outlet valve of the tank, which should
otherwise be under lock by the DPR, shall be opened.
f) Confirmatory product quality test of the first compartment of the first tanker or wagon shall be
performed. Product loading shall continue as programmed except when the confirmatory test
result is at variance with that of the tank composite sample obtained earlier on the loading day.
g) This transfer shall terminate when the program is achieved or when an emergency that
endangers the depot equipment / personnel / environment develops. The tank final level shall
thereafter be taken and the tank main outlet valve closed by the DPR.
31
PART FIVE
FIRE PROTECTION
5.0 GENERAL
In all oil installations and depots, consideration should be given to the design
Adequate provisions must also be made for fire fighting equipment for the rapid
In all oil installations and depots, serious consideration should be given to the design,
construction and layout to minimize the possibility of out break of fire. However, adequate
provisions must also be made for fire fighting equipment for the rapid extinction of any fire at
its initial stage.
LAYOUT
The general layout of facilities in installations and depot should be such that adequate fire
fighting access exists. Points of entry should be limited to the minimum necessary to prevent
access of unauthorized persons to the premises. Roadways of hard surfaced tracks should be
provided for mobile equipment and personnel to hydrants in order to permit effective and safe
use of equipment. Fire fighting equipment and hydrants should be located so that they can be
approached from different directions.
The entrances to buildings and access to fire fighting equipment should be kept clear of
obstruction at all lines. Any devices (matches, lighters etc) that may cause spark or flame
should be prohibited. Vegetation that is liable to dry out and become a fire hazard should be
kept short and all cuttings should be removed.
It is essential to ensure that adequate provisions are made for fire fighting on tanks viz:
(a) There should be provision of mobile equipment off or fixed connections for the application
of cooling water to fixed roof tanks containing class I or II (2) petroleum. Fixed water
drenchers are not always necessary in the case of floating roof tanks
(b) Fixed connections should be considered for tanks containing classes I and II petroleum
portable foam equipment should be provided in compliance with the guidelines of the
International Oil Tanker and Terminal Safety Guide as contained in Table
32
Table 4.0
Offices and Stores for dry good etc One 9 liters water type extinguisher per
100 sq. m of floor area. A fixed hose reel
may be alternatively provided.
Pump houses and pump area class I One 11kg dry chemical extinguisher per
petroleum – two pump to a maximum of four
extinguishers per four pumps with a
Class II & III petroleum maximum of two extinguishers.
Road Vehicle loading and unloading One 11kg dry chemical extinguisher per
gantries two vehicles loading or unloading position.
Rail car loading or unloading sidings One 11kg dry chemical extinguisher per
30m of siding.
33
Ship discharge or loading berths Two 11kg dry chemical extinguisher per
group of discharging or loading points. In
addition, for larger discharging or loading
facilities on 75kg dry chemical mobile unit.
2. The layout is such that adequate provisions are made for escape in the event fire and access
to fire fighting.
4. Fire drills are arranged at suitable intervals, which must include activation of fire fighting
equipment. Records must be kept of all observations.
5. Conspicuous notices should be placed at all entrances to the depots and installations
prohibiting the entry of persons smoking or carrying matches or lighters must be displayed.
Furthermore, the gantry is a hazardous area and all efforts should be geared towards ensuring
that due care is maintained always at this location. In case of any case of any spillages, it should
be diluted with water to reduce the creation of hazardous atmosphere before appropriate steps are
taken to address the problem of the spillage.
34
6.4 WELFARE AND PERSONNEL PROTECTION
The need to ensure the welfare and protection of all staff and individuals who may have cause
to be in depots and installations could not be overemphasized. These could however be
discussed as follows:
In depots and installations it is necessary that First Aid facilities for personnel should be
provided. Furthermore equipment should be always in good condition. Following recent
developments, Clinic manned trained Nurses and/or Medical Doctors are gaining greater
popularity in modern depots and installations. Standing arrangement should be made for
ambulance or medical aid. All employee should be well trained and verse with procedure for
artificial respiration and the treatment of persons suffering from electric shock. Resuscitation
equipment should be provided and a competent person always available in the
depots/installations
In depots and service station it happen that the skin gets in contact with the product. Naturally,
all petroleum products contain one chemical that should not ideally get in contact with the skin.
To reduce and/or eliminate contamination with the petroleum product, good oilfield practice
recommends among others the followings:
(a) The contaminated part of the body should be thoroughly and immediately washed with
soap and water. In the case of clothing‟s that are contaminated, they should be dry-
cleaned before re-use.
(b) If any light petroleum product is accidentally swallowed, the victim should be
immediately rushed to a Doctor or Nurse for medical attention.
(c) Skin contact with petroleum product should be avoided as far as possible.
35
6.4.3 WELFARE
The need for adequate washing facilities, drinking water and sanitation in depots and
installations cannot be overemphasized. Good oil practice recommend among others the
following:
(a) Provisions should always be made for adequate facilities for washing, drinking and
sanitation.
(d) Special attention is necessary where product vapor, mist or dust may occur, as general
ventilation should be adequate for comfort.
In all, the phases of activities in the depots and installations, relevant personnel protection
equipment should be provided. They may include; headgear, goggles, overalls, gloves and
footwear.
Furthermore, the supervisors should ensure that appropriate notice is displayed, and that the
employees put on the necessary safety protection gadgets.
It is recommended also that the employees be taught safe procedures and the importance of
abiding with relevant safety regulations. All employees should be taught how to execute their
work safely and to report accidents immediately. It is recommended that .few minutes‟ safety
talk prior to commencement of the day‟s activities is advised.
36
PART SIX
6.1 DEPOTS
a) Fiscalisation of the product tanks at the following operational intervals; i) before and
after products reception; (ii) At least 30 minutes after products reception (iii) before
and after loading operations.
b) Participate in products sampling and quality laboratory analysis to ascertain products
specifications.
c) Carry out routine inspection of Depots/Jetties facilities in order to ensure compliance
with operating Procedures and Standards
d) Keep records of the number of trucks loaded in the depot; stamping of marketers
waybill and ensure compliance with appropriate colour identification code.
e) Ensure that products are sold only to DPR licensed companies and accurate delivery
to designated trucks.
f) Ensure that products are sold only to DPR licensed companies and accurate delivery
to designated trucks.
g) Yearly appraisal on depot/jetties safety facilities and review of meter
proving/maintenance programme.
6.2 JETTIES
37
Appendix 1
CHECK LIST
Product Details Total No. Capacity of Each Tank (Liters / Vol. Applied for
Products
or Specification Of Tank(s) MT.) (Liters / MT.)
LPG
LNG
CNG
PMS
KERO
AGO
LUBE OIL
SLOP
OTHERS
38
Name of Depot Manager: ____________________________________________________
1. The above inclusions are adequate / not adequate for issuance of Approval to Construct a
Petroleum Depot (Please Circle your Conclusion).
2. Recommendation__________________________________________________________
_________________________________________________________________________
__________________________________________________________________________
Date……………………….……
Name_____________________ ___________________________
Signature and Date
4. DPR HQ Validation _________________________________________________________
____________________________________________________________________________
______________________________________
Signature and Date
39
Appendix ii
CHECK LIST
PETROLEUM PRODUCTS DEPOT CHECKLIST
(Print in capital letters only)
Field Office__________________________
Identification Code____________________
Name of Company: (As in Cert of Inc.) __________________________________________________
Regd. Address: _______________________________________________________________________
Location of Facility: ___________________________________________________________________
LGA _______________________________ State: ________________________________________
40
Product Details or Total No. Of Capacity of Each Tank (Liters / Vol. Applied for (Liters /
Products
Specification Tank(s) MT.) MT.)
LPG
LNG
CNG
PMS
KERO
AGO
LUBE OIL
SLOP
OTHERS
1. The above inclusions are adequate / not adequate for issuance of License to Operate the Petroleum Depot (Please
Circle your Conclusion).
2. Recommendation__________________________________________________________
__________________________________________________________________________
Name of Inspectors
________________________________ ________________________________
Signature and Date
________________________________ ________________________________
Signature and Date
________________________________ ________________________________
Signature and Date
Name of Head of Department ______________________ _____________________
Signature and Date
3. OPSCON’S Comment _______________________________________________________
____________________________________________________________________________
Name_____________________ ___________________________
Signature and Date
4. DPR HQ Validation _________________________________________________________
____________________________________________________________________________
Name of Officer _______________________ ___________________________
Signature and Date
5. License to Operate granted by _________________________
______________________________________
Signature and Date
41
Appendix iii
DEPOT INSPECTION REPORT
1.0 LOCATION_________________________________________________________________________________
42
Appendix iv. 2.0 TRUCKS LOADING AREA
LOADING DAT E
B AY ARM METER P UM P METER P RO DUCT COMMENT
NO . NO . NO . NO . PROVED
43
2.1 TRUCK LOADING AREA:
3.0 LABORATORY
API SEPERATOR
______________________________________________________________________________
______________________________________________________________________________________
SKIMMERS
______________________________________________________________________________________
45
5.0 GENERAL SAFETY PROVISIONS
FIRE EXTINGUISHERS
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
SAFETY WEARS
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
SAFETY SIGNS
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
FIRE TRUCKS
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
SPARK ARRESTORS
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
HYDRANT SYSTEM
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
____________________________________________________________________________________
NAME & SIGNATURE OF DPR STAFF
46
Appendix v
SECTION A:
1. Name of Applicant/Company:
………………………………………………………………..……………
………………….………………………………………………………………………………
…………………..
c. Depot [ ]
5. State whether application is for a NEW Licence or RENEWAL Licence, and the
corresponding year(s):
……………………………………………………………………………………….
47
If RENEWAL, please attach photocopy of the expiring license
6. Storage Capacity:
8. Has the petroleum station‟s draft Management Agreement been verified and endorsed by the
DPR? {YES/NO/Not Applicable}.
9. I/We hereby certify that all the information given above are correct.
…………………………………………………………………………………………………
………………………
(in words)
…………………………………….………………………………
……………………………
48
SECTION B: TO BE COMPLETED BY THE SPONSORING MARKETING COMPANY ONLY
We hereby undertake to sponsor this application for the grant of license to store and sell. (Petroleum
Decree 1969).
Note
a. Where an applicant obtains product(s) from more than one company, applications should be
channeled through only one company.
b. Application not properly filled will be rejected and fees in respect of such rejected application
will neither be refunded nor transferred on to any other application
c. An application must be submitted in respect of each Category (under 4 above) Bank Draft to
be made payable to the:
d. Whereas Pressure Test Certificate and Report are required ensure that duly signed
ORIGINAL CERTIFICATE are forwarded to LAGOS through respective zonal office of the
DEPARTMENT OF PETROLEUM RESOURCES (DPR).
…………………………………………………………
……………………………………………
49
SECTION C: DEPARTMENT OF PETROLEUM R ESOURCES Use Only
(in words)
………………………………………………..…………………..
………………………………………………
Licence Number:
…………………………………………….……………………………………………………………
…………………………………….. …………………………………………………..
…………………
50