Professional Documents
Culture Documents
19-Final Report PDF
19-Final Report PDF
Team # 19
2011-12-05
Names of Team Members:
Brian J. Nuessler
________________________
John M. Bais
________________________
Steven N. Young
________________________
Qiankun Zhao
________________________
UMSAE BAJA TRANSMISSION DESIGN
Letter of Transmittal
We are submitting to you this report, due December 6th, 2011, which outlines our final
design for the UMSAE Baja transmission. The report focuses on the features of our
design, as well as cost and technical analysis. The design is the result of considering a
number of alternatives, which were carefully screened based on our clients’ needs. If
you should have any questions concerning our report or project, please feel free to
contact me, John Bais, at 204-979-2073.
Sincerely,
John Bais
Team Leader
ii
UMSAE BAJA TRANSMISSION DESIGN
Abstract
The University of Manitoba SAE (UMSAE) Baja team is a school group that designs,
builds and races an off-road vehicle every year. The team has requested a re-design of
their powertrain system, as they have had problems with the operation of the vehicle at
last year‟s competition. This report describes the final design that will best meet the
needs of the Baja team. The design was chosen by narrowing down a list of concepts
based on the needs of the Baja team and the required technical specifications of the car‟s
powertrain. Four designs met those needs and were researched further after which a final
The design selected is an Infinitely Variable Transmission (IVT) system, which is created
gear set. The sun gear of the planetary set is driven directly by the engine and the ring
gear is driven through the CVT which is attached to the engine. Changing the CVT ratio
changes the speed of the ring gear which, in turn, creates a difference in the speed of the
ring and sun gears. This difference causes the planet gears to displace, which is the output
of the system to the wheels. A pair of gears reverses the direction of rotation of the ring
gear and a sprocket set is added to give the ability to easily change the overall reduction
ratio of the system. This system offers high low-speed torque while still providing a high
top speed and, for this reason, an IVT system will be the best option for the Baja team.
iii
UMSAE BAJA TRANSMISSION DESIGN
TABLE OF CONTENTS
1 Introduction............................................................................................. 1
1.1 Project Objectives ............................................................................ 2
1.2 Target Specifications ........................................................................ 3
1.2.1 Analysis of Customer Needs ....................................................... 3
1.2.2 Technical Specifications ............................................................. 4
3 Conclusion ............................................................................................. 24
4 Bibliography .......................................................................................... 25
iv
UMSAE BAJA TRANSMISSION DESIGN
LIST OF TABLES
TABLE III - TERMS USED TO DETERMINE THE FINAL RATIO OF IVT OUTPUT .......................................10
SYSTEM................................................................................................................................................................11
LIST OF FIGURES
Figure 3: The IVT powertrain system exploded view of assembly by Team Trans-Formers............................. 7
Figure 4: Engine RPM vs. velocity profiles for gears, CVT and IVT systems ..................................................... 8
Figure 11: 6160 AL plates, gear and pinion, and gear case enclosure .............................................................23
v
UMSAE BAJA TRANSMISSION DESIGN
1 Introduction
The UMSAE Baja team competes in an annual competition with a student-designed off-
road vehicle and has requested a redesign of its powertrain system. The current
powertrain system consists of a Polaris CVT clutch and a UMSAE Baja custom made
gear box. The custom gear box has high, low, and reverse settings, as well as a lockable
The gearbox will not stay in gear and slips into neutral when strong torque loads
are applied.
The UMSAE Baja team has a powertrain system design that goes from the stock engine to
the rear axle. The design should also include the driver controls for the system to improve
the ergonomics of the shifting system. The transmission system that will be designed
should allow for the tires to spin independently thus improving the vehicle‟s
manoeuvrability. At the same time, the system developed should have the versatility to
handle events such as the rock crawl where all four tires will not always be in contact with
the ground. The SAE competition rules state that a Briggs & Stratton Intek 20 engine
must be used by all teams, therefore the design is limited by those operating specifications
increased while reducing the system‟s weight, these are often contradictory objectives.
1
UMSAE BAJA TRANSMISSION DESIGN
The goal of this project is to improve the performance of the 2011 Baja powertrain design.
This project will focus on the analysis of the current system and the design of a new
transmission system for the Baja vehicle. The design will also include analyses,
calculations, and full justification of all components involved in the final design.
● Able to provide gearing to keep the engine within the optimum power band
2
UMSAE BAJA TRANSMISSION DESIGN
The aim is to produce a design that meets all of the above requirements so that the Baja
To optimize the design of a new Baja transmission system and aid in the selection of
feasible power transmitting alternatives, a table of customer needs has been made
according to the corresponding technical specifications. The metrics associated with the
technical specifications are identified and listed, as well as their current and target values.
The transmission design must satisfy the customer needs in Table I below. Each customer
need has a corresponding importance value ranging from 1 to 3, with 1 being the most
3
UMSAE BAJA TRANSMISSION DESIGN
The technical requirements of our design, based on the needs of our customer, are
Thirteen concepts were developed, and the team then screened those concepts on how
well they met the basic needs of our customer. This produced four design concepts which
were then scored based on their technical abilities. The final design concept was chosen
4
UMSAE BAJA TRANSMISSION DESIGN
After doing an in-depth concept analysis on the designs that were being considered, the
team decided that an Infinitely Variable Transmission (IVT) system would be the best
choice, as it scored well in all of the technical specification categories. An IVT powertrain
A CVT is essentially a pair of pulleys with tapered walls that are able to move in and out.
This allows for a continuous range of gear ratios where no gear shifting occurs. This is
beneficial when compared to gears which can only provide a small number of different
ratios. Gears are relatively inefficient when it comes to reductions as the engine is not
kept within its optimum power band, but rather fluctuates around the optimum operating
point. A CVT however, provides this continuous range in the forward direction only and
the reduction is only available from a certain minimum speed. This is due to the fact that
the weights in the pulleys control the ratio. A continuous range is not offered in reverse. It
would be beneficial for the forward range to be available from the instant the car starts to
move. Therefore, converting a CVT to an IVT will provide the benefits of a CVT while
In order to convert a CVT into an IVT, a planetary gear set must be used and the engine
must also operate differently. A planetary set is made up of a sun gear, a ring gear, and
multiple planet gears. The planet gears mesh with the ring and sun gears, which spin in
opposite directions. When the angular velocity of the ring and sun gears are equal, the
displacement of the planet gears, and therefore the output of the system, will be zero. By
5
UMSAE BAJA TRANSMISSION DESIGN
changing the ratio of the CVT, the ring and sun gears rotate at different speeds relative to
Sun
the pulleys would be controlled by weights that would change the ratio as the speed
increases. For an IVT, the engine runs at the desired optimum point at all times, which
would keep the sun gear and the CVT primary clutch rotating at a constant speed. The
CVT controls the speed of the ring gear. The difference in the speed of the two gears is
As discussed in the last section, an IVT can be built using a CVT and a planetary gear set.
This section details the features of an IVT system as well as methods of controlling it.
6
UMSAE BAJA TRANSMISSION DESIGN
A render of the IVT powertrain system can be seen in Figure 2 and Figure 3.
Figure 3: The IVT powertrain system exploded view of assembly by Team Trans-Formers
7
UMSAE BAJA TRANSMISSION DESIGN
2.1.1 Performance
The powertrain system directly affects the performance of the vehicle. The IVT
CVT system in the sense that there is no need to shift between gears while accelerating. In
the CVT system the engine RPM follows a linear curve. The IVT holds the engine at a
constant RPM from the neutral position to the maximum velocity. Figure 4 shows the
profiles of the engine RPM verses velocity for a powertrain system using gears, CVT and
IVT.
Figure 4: Engine RPM vs. velocity profiles for gears, CVT and IVT systems
Since the engine can be held at a constant RPM, which can easily be adjusted by the
driver, the maximum power from the engine can always be obtained. Having the engine
produce maximum power at virtually all times means that not only will the IVT
8
UMSAE BAJA TRANSMISSION DESIGN
powertrain system deliver substantial low end torque and high end top speed, but it will
also deliver full mid-range performance. Also, the IVT system places less stress on the
engine, as it is held at a constant RPM and doesn`t fluctuate. Consistent RPM is ideal for
the Brigg`s and Stratton engine which is not designed for racing applications.
Another advantage the IVT system has over a traditional transmission where gears are
used is that there is no impact to the system that is normally associated with shifting from
one gear to the next. Also, without a need to shift gears into reverse, there is no chance
that the powertrain system can ever be engaged in two settings at the same time.
In addition to the overall performance of the vehicle, the IVT system also allows the
engine to be lowered to the bottom of the frame. The engine contributes a large portion of
the overall weight of the powertrain system, and by keeping the engine lower, the center
of gravity will also be lowered which will improve the handling of the Baja vehicle.
The final gear ratio reduction of an IVT system occurs through a series of reductions from
each component. Changing one component can greatly affect the final ratio. However the
components. The features of the IVT system, as well as how other components in the
powertrain are affected by the IVT will be explained it the following sections. The
equation for the final ratio of the system and the description of the variable used is given
below. Descriptions of the variables in the equation for the final output ratio are outlined
in TABLE III.
9
UMSAE BAJA TRANSMISSION DESIGN
TABLE III - TERMS USED TO DETERMINE THE FINAL RATIO OF IVT OUTPUT
Variable Details
Ns # of teeth on sun gear
Nr # of teeth on ring gear
Ae Angular displacement of the engine
Rcvt Ratio delivered from the CVT
Rsp Ratio delivered from the sprockets
Rg Ratio delivered from the gear and pinion
Rd Ratio delivered from the differential
Rf Overall angular displacement of the engine to the rear axle
{ }
The design of this powertrain system is unique in the sense that the overall ratios can be
easily adjusted. As a result, many different CVTs and differentials can be used and
interchanged with the current ones used. The accommodation of different CVTs and
differentials is possible because the ratio of the sprockets within the powertrain system
plays a large a role in the ratio of the entire system. A small change to the ratio in the
sprockets generates a large change in the maximum and minimum ratios seen from the
input to output of the powertrain system. The sprockets are easily accessible and new
sprockets are readily available on the market. An example of how the system could be
updated by adjusting the sprockets is seen in TABLE IV. If the current Polaris CVT was
replaced with the CVTech clutch, the maximum speed theoretically achievable would be
an unrealistic 166.7 km/hr. However, the ratio is corrected with only a small change in
10
UMSAE BAJA TRANSMISSION DESIGN
The ability of the system to accommodate the exchange of the clutch and differential
means that the system can be progressed as better components become available.
2.1.2.2 Differential
The engine within the IVT powertrain system has been rotated by 90 degrees so that the
input shaft from the engine now rotates perpendicular to the rear axle. The previous
UMSAE Baja vehicles have always had the engine positioned so that the input shaft of the
engine was parallel to the rear axle. Having the input shaft of the engine perpendicular to
the rear axle is an attractive feature because there is a greater variety of locking
differentials available on the market that have this orientation. The Baja team currently
11
UMSAE BAJA TRANSMISSION DESIGN
The Polaris Ranger rear locking differential is used for this design because of its
availability to the Baja team. This differential is designed to handle a larger amount of
torque and is therefore heavier and bulkier than what is needed for the Baja vehicle.
Nevertheless, as previously stated the differential can be interchanged for a new model as
The CVT clutch is used to change the output ratio of the powertrain system. However,
since the engine is always held at a constant rpm, instead of the position of the CVT being
automatically adjusted by the rpm of the engine, the CVT position will be adjusted by
driver input. The CVT can be adjusted by the use of either a linear actuator or by
mechanical linkages. For the scope of this project the linear actuator is recommended
because of its simplicity of manufacturing and integration into the system. The linear
12
UMSAE BAJA TRANSMISSION DESIGN
The weights and spring on the CVT that normally control the position of the tapered walls
are not needed for the IVT powertrain system and can therefore be removed as seen in
Figure 6.
13
UMSAE BAJA TRANSMISSION DESIGN
The modifications to the Polaris P90 CVT can easily be performed by a hand milling
operation. The Polaris P90 CVT clutch has been recommended for the IVT powertrain
system because the Baja team currently has access to one. The Polaris P90 CVT clutch is
designed to handle a greater torque and horsepower then the Baja engine can produce. A
CVTech clutch would be an alternative that would offer a smaller and lighter option in the
2.1.3 Controls
The output of an engine in a normal vehicle is controlled by a foot pedal that has a direct
effect on the speed of the vehicle. However, because an IVT does not produce an output
the same way as a normal vehicle would, the methods of controlling it are different as
well. To control the IVT powertrain system the foot petal, throttle control and hand
The IVT powertrain is controlled in a very different way than most automotive powertrain
systems. The “gas pedal” of the system will not control the throttle position. Instead the
foot pedal will control the Polaris P90 secondary clutch position through a linear actuator.
In other words, the driver would be in control of the overall power train ratio not the
engine power. The IVT system would require more driver-training than a traditional
14
UMSAE BAJA TRANSMISSION DESIGN
Since the throttle to the engine is held at a constant position, the control can be
independent of the foot controlled “gas pedal”. The throttle control will be on the dash
board of the vehicle and will hold its position after the driver has selected the desired
position. To maximise power during racing applications, the throttle can be set to the
optimum limit. To conserve fuel and reduce noise, a lower throttle position can be
selected. While in forward drive, the only input from the driver to the IVT system is
through the “gas pedal”, allowing the driver to keep both hands on the wheel to increase
performance.
To reverse the vehicle with the IVT system, the driver will need to remove their foot from
the “gas pedal” and pull the reverse lever. The reverse lever moves the CVT position past
the neutral zone and into the reverse zone. Since very little time is spent in reverse,
coupled with the slow associated speeds, it was determined that the reverse lever would
be held to engage motion and spring back to neutral upon release. When the reverse lever
is released, the car will be instantly ready to drive forward without the need for additional
driver input.
A lever that controls the locking and unlocking of the differential is also required. There
is a switch directly on the differential that controls the locking mechanism. A simple
mechanical linkage consisting of a push pull cable will be used to complete this task.
It is recommended that the reverse lever and the differential lever be placed on opposite
15
UMSAE BAJA TRANSMISSION DESIGN
2.2 Operation
The IVT system designed for the UMSAE Baja team uses the planetary system to achieve
an infinite range in ratio output between maximum speed in the forward direction and
reverse direction. A simplified schematic of the IVT system can be seen in Figure 7.
Ring
Planets
Sun gear
P
i
n
Engine Differential
i
o
n
G
e
a
r
Sprockets
CVT
output shaft of the engine are the primary CVT pulley and the sun gear of the planetary
system. The primary and secondary pulleys of the CVT are connected through the belt of
the CVT and as a result the output of the CVT is still rotating in a counter clockwise
16
UMSAE BAJA TRANSMISSION DESIGN
direction. From the output shaft of the CVT the first sprocket is connected. The first and
second sprockets are connected via chain and are both spinning in the counter clockwise
direction. The shaft that holds the second sprocket also holds the first gear. The second
gear transfers the rotation from the first gear to the case of the ring gear. The second gear
provides the change in rotation for the ring gear necessary for the IVT to operate. The
sun gear and the ring gear work together to control the output of the planetary gear carrier.
The planetary gear carrier can rotate either in a clockwise or counter clockwise direction
depending on the relative speeds of the ring and sun gears. The planetary gear carrier is
directly connected to the input of the differential. Finally the differential is connected to
2.2.1 Gears
A pair of gears is required in the IVT system to transmit power from the sprocket to the
ring gear, as well as reverse the direction of rotation. To determine the required size of
these gears, a decision was required as to the gear ratio, as well as the diameters of the
gears. It was decided that the desired ratio through the gears and sprockets should to be
0.9:1. That ratio was assigned to the gears, meaning the sprockets could then have a ratio
of 1:1. The diameters of the gears were limited by the center to center distance between
the shaft going from the CVT to the sprocket and the shaft going from the engine to the
sun gear. These maximum pitch diameters of 4.5 and 5 inches respectively were noted
and, using the desired gear ratio, the appropriate gears were found.
Suitable gears were found on Martin Sprocket‟s website that will fit within the size limits
of the design. The diameter of the driving gear is 5 inches, while the diameter of the
driven gear is 4.5 inches. The slowest speed that the gears will experience corresponds to
17
UMSAE BAJA TRANSMISSION DESIGN
the maximum torque and it was possible to calculate the minimum face width of both
gears (calculations shown in Appendix B). The minimum face width was found to be 0.3
inches for both gears, but it was decided a width of 0.5 inches was more appropriate as
alignment could be an issue with very thin gears. The gears offered by Martin Sprocket
come with face widths of about 3.5 inches. The gears must therefore be cut down to the
desired width of 0.5 inches. The final dimensions of the gears are outlined in TABLE V.
Sprockets and chains are used to transmit power from the output of CVT to the ring gear
of the planetary gear set. They are more compact, lighter, and efficient compare to spur
gears. Another beneficial feature is that the sprockets and chains can be isolated from the
main transmission casing so that they are easily accessible from the outside. Since the
overall gear ratio is very sensitive to the change in ratio between the sprockets, the Baja
team has the freedom to adjust the overall gear ratio very easily by changing to a different
A Briggs & Stratton 10 HP Intek Pro Engine is used for the power source for the system.
According to the CVT design, the maximum rpm at front sprocket would be 5000rpm.
Based on the gear ratio optimizations, it is determined that a 1:1 ratio for the sprockets
and chains system would be optimal. By considering the power rating and maximum rpm
18
UMSAE BAJA TRANSMISSION DESIGN
it was decided to use 15 teeth 520 steel sprockets from Kawasaki for both front and back
sprockets and a DID 520 ATV X-Ring chain. A sprocket and chain system summary is
listed in TABLE VI and detailed calculations for the sprocket chain set up are provided in
To make the IVT transmission system cost effective, it was decided to purchase parts that
that are commercially available. Since the UMSAE Baja team consists of student
volunteers, the manufacturing and labour cost to implement the design will not be a factor.
This means that only cost to develop this IVT transmission system will be the cost of
parts and material. Since the Baja team is a non-profit student organization, most of the
parts required are either donated or discounted through sponsors. Therefore, the team will
be able to implement the whole IVT transmission system for an estimated cost of less than
$1900 CAD. A detailed cost breakdown is listed in Appendix C page 39 and the bill of
19
UMSAE BAJA TRANSMISSION DESIGN
2.4 Manufacturing
The IVT system will be largely comprised of purchased parts. Many of the major
components for the IVT powertrain system will be purchased and modified to work with
the system. The modification and manufacturing of the main components will be
explained in this section of the report. It should be noted that the UMSAE Baja team has
The P90 Polaris CVT will have the weights that control the automatic shifting removed
and an adapter will connect it to the linear actuator. This can be seen in Figure 8.
20
UMSAE BAJA TRANSMISSION DESIGN
The actuator assembly will have a bearing housing and adaptor attached to the end of its
shaft. The housing connects the actuator to CVT adaptor and allows the CVT to spin
freely. The housing and adaptor will need to be custom made. It is not a complicated part
and can be produced on a standard lathe and milling machine. The actuator housing and
The planetary gear system will be bought and will only require a small modification. The
second gear in the IVT system must be connected to the ring gear concentrically. This is
accomplished by making the rotating output flange. The rotating output flange can also be
produced with a standard lathe and drilling operations. The rotating output flange can be
seen in Figure 9.
21
UMSAE BAJA TRANSMISSION DESIGN
The spur gear and pinion will be produced from Martin Sprocket Inc. gear blanks made of
1144 steel [4]. The UMSAE Baja team is sponsored by Martin sprocket and has machined
22
UMSAE BAJA TRANSMISSION DESIGN
and heat treated gear blanks like these in the past. Therefore there will be no issue with
fabrication these gears for the Baja team. The gear and pinion will need to be machined to
The main support and frame of the IVT planetary system is made from 6061 Al plates as
seen in Figure 11. This structural plate can be machined on a 3 axis CNC machine
available to the UMSAE Baja team. The gear case enclosure is comprised of two parts:
the front plate and the center enclosure seen in Figure 11. The gear case enclosure can be
produced in a several different ways. The center pattern of the enclosure can be cut out
with a water jet cutter. The critical sections of the gear case, such as bearing locations,
would call for additional machining to achieve the needed tolerances. If water jet cutting
is not available, the gear case can be machined by a 3 axis CNC machine. The front plate
Gear Case
Front Plate
Center Pattern
Figure 11: 6160 AL plates, gear and pinion, and gear case enclosure
23
UMSAE BAJA TRANSMISSION DESIGN
3 Conclusion
The purpose of this project was to design a powertrain system for the UMSAE Baja team.
The request for the redesign of the current powertrain system was in response to the
performance issues from the 2011transmission. The 2011 powertrain design was
comprised of the standard Brigg‟s & Stratton engine, a P90 Polaris CVT and a custom
transmission (IVT).
Unlike a gear style of transmission where only finite ratios can be achieved, the IVT
system allows for a wide range of ratio outputs. The full range of output ratios extends
from full speed in the forward direction, through neutral, to a full output speed in the
reverse direction. The IVT system delivers better performance because it allows the
engine to operate at its maximum power output at all times. The IVT offers a top
theoretical forward speed of 85 [km/hr] and a reverse speed of 1.2 [km/hr]. Another
attractive feature of the IVT system is that the overall system output ratio can be altered
The IVT designed, meets or surpasses all the requirements requested from the UMSAE
Baja team. The powertrain system was given a budget of $5,000. The IVT powertrain will
cost the UMSAE Baja team $1,854.34 CAD and is therefore under budget. The new IVT
powertrain system was designed with the UMSAE Baja team in mind so that every part of
the system will be within the manufacturing capabilities of the Baja Team. The IVT
system is a rugged design that will withstand the demands of the UMSAE Baja
24
UMSAE BAJA TRANSMISSION DESIGN
4 Bibliography
[2] Continuously Variable Transmission. (2008, Sep.). How to Convert a CVT Into a
[3] DID Chain Inc. (2010, Sep.). DID Racing Chain [Online].
[4] Martin Sprocket & Gear, Inc. (2010, Oct.). Spur Gears [Online].
[5] Robert L. Mott, Machine Elements in Mechanical Design, 4th ed. USA: Pearson
Available:http://www.rexnord.com.br/webpts/inbox/downloads/8/16%20-
25
APPENDIX A.- ALTERNATIVE CONCEPTS
UMSAE BAJA TRANSMISSION DESIGN
Multiple designs were considered, and the final design was chosen based on the screening
Screening Matrix
Table 1 below was used to choose four designs to be considered for a final design.
Design Options
27
UMSAE BAJA TRANSMISSION DESIGN
Needs
1 - must transfer power from the engine to the wheels
2 - must be optimized for each dynamic event
3 - must be durable
4 - provide different gear ratios
5 - must be easily manufactured
6 - must be able to operate in a variety of terrains
7 - must be packaged to keep the center of mass as low as possible
8 - minimal power losses
9 - cost effective
10 - relatively small
11 - relatively light
Designs
1/2 - multiple planetary gears or planetary gears with a CVT
3 - hydraulic system powered by engine
4/5 - chain drive or belt drive
6 – dual CVT directly from the engine to the rear wheels
7 - electric motor(s) powered by generator which is connected to the engine
8 - pneumatic system gets power from air tank connected to compressor connected to
engine
9 - fan boat propeller powered by engine
10 - bicycle-style sprockets
11 - rocket powered
12 - cone-style CVT
13 - friction wheels
28
UMSAE BAJA TRANSMISSION DESIGN
Scoring Matrix
A sample of the concept scoring process is shown below. This particular scoring matrix is
for a powertrain system comprised entirely of sprockets and chains, similar to a bicycle.
29
UMSAE BAJA TRANSMISSION DESIGN
30
UMSAE BAJA TRANSMISSION DESIGN
All of the terms used to solve the ratio delivered from the IVT system is given in TABLE
III. It should be noted that the angular displacement of the sun gear(As) is equivalent to
To determine the ratios for the IVT system the problem was first simplified. Starting with
the planetary system two situations were combined by superposition. The two situations
are; when the ring gear is locked in place (sun gear input, planet carrier output) and when
the sun gear is locked in place (ring gear input, planetary carryout output). The equations
Variable Description
Ns # of teeth on sun gear
Nr # of teeth on ring gear
Ar Angular displacement of ring gear
As/Ae Angular displacement of sun gear/engine
Acr Angular displacement of planet carrier with ring gear free to spin and sun gear locked
Acs Angular displacement of planet carrier with sun gear free to spin and ring gear locked
Ac Overall angular displacement of the planet carrier
Rcvt Ratio delivered from the CVT
Rsp Ratio delivered from the sprockets
Rg Ratio delivered from the gear and pinion
Rd Ratio delivered from the differential
Rf Overall angular displacement of the engine to the rear axle
31
UMSAE BAJA TRANSMISSION DESIGN
The input from the ring gear and sun gear will have a cancelling effect on the output of
the planet carrier. The rotation of the ring gear can be related to the rotation of the sun
gear through the CVT, the sprockets and the gears. The differential changes the overall
final output of the system in a linear fashion. Using this information the following
By rearrange these equations the overall ratio of the powertrain system can be determined.
Also it will be possible to use the equation to manipulate the overall ratios by changing
the internal rations between the components. The equation for the overall ratio of the IVT
system is as follows.
{ }
32
UMSAE BAJA TRANSMISSION DESIGN
Ratio = 0.9:1
33
UMSAE BAJA TRANSMISSION DESIGN
Maximum allowable bending stress number for flame-hardened steel (st,max) = 45 ksi
(Table 9-3)
Maximum allowable bending stress number for flame-hardened steel (sC,max) = 170 ksi
(Table 9-3)
The values for st and sC were obtained by varying the face width until the stress numbers
were below the acceptable values. The final minimum face width is:
34
UMSAE BAJA TRANSMISSION DESIGN
Based on Manufactures specification DID 520 ATV X-Ring chain has a pitch of 5/8
inches [3].
Since the best sprockets ratio is determined to be 1:1, therefore both sprockets will have
15 teeth.
On ratios of less than 3:1, wrap will always be at least 120° in a two sprocket system. The
minimum center distance to avoid interference between the two sprockets can be
( )
Where:
For the purpose of our design the actual center distance between sprockets will be used as
( ) ( )
35
UMSAE BAJA TRANSMISSION DESIGN
Since the ratio is 1:1, then the angle of wrap for each sprocket would be the same and can
be determined as:
Where:
36
UMSAE BAJA TRANSMISSION DESIGN
37
UMSAE BAJA TRANSMISSION DESIGN
The cost of the IVT powertrain system was broken down into three sections. The three
sections are the normal cost, sponsored cost and current cost. The normal cost is the full
price without any sponsorship or in-kind donations. The sponsored cost is the amount the
IVT system would cost the UMSAE Baja team from sponsors. The current cost of the
system takes into account not only the sponsorship discounts and in-kind donation, but
also the parts and material the Baja team already has. An example of this is the Polaris
P90 CVT. Polaris is a sponsor and therefore the Baja team received a discount on the part,
but the Baja team already has a P90 CVT in their possession that could be used for the
IVT system. Therefore, the current cost of the P90 CVT is free to the Baja team.
Major components for the IVT system that are listed as a current cost of $0.00 are either
in-kind donations from the Baja sponsors or the Baja team already has these components
from previous years. The material costs are estimated from the current cost of materials
from AED motor sports. AED motor sport offers a discount for all the metals that will be
used for the IVT system. Hardware such as bearings and fasteners are donated to the Baja
The detailed breakdown and summary of the cost from the IVT system are outlined in
table 4 .
38
UMSAE BAJA TRANSMISSION DESIGN
Components Series
Sprocket x2
Chain
Automation
AL 7075
39