GEK - 91716 Shipping Instructions 5GDY106
GEK - 91716 Shipping Instructions 5GDY106
SCOPE
This publication explains the procedure for preparing the GDY106 Motorized Wheel for shipment. Included are
methods for locking the rotor, prep for shipping, securing the motorized wheel to the shipping skid, securing the motor-
ized wheel/skid to the flatbed, and the dimensions for building the skid.
NOTE: If assembled Motorized Wheel is to be transported a distance necessitating the use of a shipping
skid, the rotor must be locked.
1
2
4
5
REF. DESCRIPTION
1 TIE WRAP
2 TAG
3 BAR
4 BRAKE ADAPTER
5 SHIPPING BOLT
Copyright 2002 General Electric Company. All rights reserved. This copyrighted document may be reproduced free of charge by General
Electric Company customers (OEM’s) and their customers, if such reproduction is used exclusively in connection with equipment used in
those customers’ internal operations.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation, or mainte-
nance. Should further information be desired or should particular problems arise which are not covered sufficiently for the user’s purposes, the matter should be referred to the General
Electric Company. Any applicable Federal, State or local regulations or company safety or operating rules must take precedence over any instructions given in this material. GE has no
obligation to keep the material up to date after the original publication.
THERE ARE NO WARRANTIES OF ACCURACY, MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE.
Verify numbers for parts, tools, or material by using the Renewal Parts or Tool Catalogs, or contact your
General Electric representative for assistance.
Do not order from this publication.
GEK–91716, Shipping Instructions For 5GDY106 Motorized Wheel
1. Place two bars (3) behind the brake adapter (4). Align the two bars with two of the holes in the brake adapter.
2. Install shipping bolts (5) through two of the holes in the brake adapter (4) against the bars (3).
3. Tighten the shipping bolts against the bars (3) with 30 ft.–lbs. of torque.
5. Attach a WARNING tag (2) to each of the two bars (3) with a tie wrap (1), or connect the locking bars with one tie
wrap and a WARNING tag.
3. Slush mounting flange, brake hub, and all external unpainted, machined surfaces with Ferrocote 5856 BF rust
inhibitor, GE ID No. 41A330160P1 (available from the Quaker Chemical Corp).
3 REF. DESCRIPTION
1 FLANGE END BAND
1
2 5GEB16 MOTOR
3 SHIPPING SKID
4 HUB END BAND
2
Shipping Instructions For 5GDY106 Motorized Wheel, GEK–91716
1. Place the shipping skid (3) on two pieces of scrap lumber. (This is to allow banding.)
WARNING: The weight of a complete GDY106 less brakes, tires, rims and tire mounting hardware is
approximately 40,000 lbs. Use the proper crane, cables, and devices when moving the wheel motor.
2. Lift the motorized wheel using two heavy duty hoist rings through the flange holes and a chain sling around the
hub. Use lifting cables rated for a load of at least 40,000 lbs.
NOTE: An alternate way of lifting the motorized wheel is to use two chain slings, one between the flange
and the brake and one around the hub for straight lifting. Do not lift AC Wheel with the lifting lugs on the
GEB16 motor or by using chain slings around the motor.
WARNING: If the cables used for lifting the wheel motor are not in a vertical alignment the resulting ten-
sion will be higher than 40,000 lbs. Use lifting cables rated for the appropriate load in these cases.
3. Place the motor on the skid: the bottom of the flange fits into the slot and the wheel hub rests on the curved part
of the skid cradle.
4. Cover the parking brake end with sheet plastic.
5. Secure the motorized wheel to the skid with two metal shipping bands as follows:
b. Place the wheel hub–end band (4) around the wheel hub and skid, centered with the skid cradle.
3
GEK–91716, Shipping Instructions For 5GDY106 Motorized Wheel
18.00
FIT TO 1
CURVATURE
OF HUB
1 FIT TO
CURVATURE 12.00
OF FLANGE
18.00
1
72.00
66.00 40.00
3 4
5 5
21.00 2 1
12.00 2
144.00 REF.
REF. DESCRIPTION
1 BOTTOM SUPPORT – HARDWOOD 3X6X144
2 CROSS SUPPORT – HARDWOOD 3X6X72
3 HUB SUPPORT – HARDWOOD 4X6X72
4 HUB SUPPORT – HARDWOOD 2X6X72
5 HUB SUPPORT – PLYWOOD 3/4X11X72
GE Transportation
Systems
2901 East Lake Road
NEW 12/02 BWV Erie, Pennsylvania 16531
PRINTED
IN
U.S.A.
E