User'S Manual of FGSD / FGSW Web Smart Poe Switch
User'S Manual of FGSD / FGSW Web Smart Poe Switch
1
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Trademarks
Copyright © PLANET Technology Corp. 2015.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
PLANET 8/16/24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart Ethernet Switch User's Manual
2
User’s Manual of FGSD / FGSW Web Smart PoE Switch
TABLE OF CONTENTS
1. INTRODUCTION.................................................................................................................... 6
2. INSTALLATION ................................................................................................................... 16
3.1 Requirements..............................................................................................................................................29
4.2 System.........................................................................................................................................................38
4.2.1 System Information..............................................................................................................................................38
3
User’s Manual of FGSD / FGSW Web Smart PoE Switch
4.4 VLAN............................................................................................................................................................53
4.4.1 VLAN Overview ...................................................................................................................................................53
4
User’s Manual of FGSD / FGSW Web Smart PoE Switch
7. TROUBLESHOOTING....................................................................................................... 106
5
User’s Manual of FGSD / FGSW Web Smart PoE Switch
1. INTRODUCTION
Thank you for purchasing 8/16/24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart Ethernet Switch.
FGSD-1008HPS 8-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/ SFP combo Web Smart Switch
FGSW-1816HPS 16-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart Ethernet Switch
FGSW-2624HPS 24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart Ethernet Switch / 220W
FGSW-2624HPS4 24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart Ethernet Switch / 420W
“PoE Web Smart Switch” is used as an alternative name in this user’s manual.
Rubber Feet x4
Power Cord x1
If any item is found missing or damaged, please contact your local reseller for replacement.
6
User’s Manual of FGSD / FGSW Web Smart PoE Switch
1000X Fiber Optic 2 x SFP Slot 2 x SFP Slot 2 x SFP Slot 2 x SFP Slot
PoE+ Ports 8 16 24 24
PoE Budget 125 watts 220 watts 220 watts 420 watts
Enclosure 13” metal case 19” metal case 19” metal case 19” metal case
Centralized Power Management for Security and Public Service PoE Applications
To fulfill the needs of the high power consumption of PoE network applications, the FGSD / FGSW-series PoE Web Smart
Switch features the standard IEEE 802.3at Power over Ethernet Plus (PoE+) that combines up to 30 watts of power output
and data per port over one cat5E/6 Ethernet cable. It is designed specifically to meet the demand of the high power
consumption of network PDs (powered devices) such as IR, PTZ, speed dome cameras; and even box-type IP cameras with
built-in fan and heater. Compliant with both 802.3at and 802.3af standards, the series allows more flexibility in power
7
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Section 2, INSTALLATION
The section explains the functions of the Switch and how to physically install the PoE Web Smart Switch.
Section 7, TROUBLESHOOTING
The chapter explains how to troubleshoot the PoE Web Smart Switch.
Appendix A
The section contains cable information of the PoE Web Smart Switch.
8
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Layer 2 Features
Auto-MDI/MDI-X detection on each RJ45 port
Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
Supports broadcast storm control
Supports VLAN:
- IEEE 802.1Q tag-based VLAN, up to 32 VLANs groups, out of 4095 VLAN IDs
- Port-based VLAN, up to 16 VLAN groups
- MTU VLAN (Multi-tenant Unit VLAN)
Supports Link Aggregation
- 802.3ad Link Aggregation Control Protocol (LACP)
- Cisco ether-channel (Static Trunk)
Supports Spanning Tree Protocol
- STP, IEEE 802.1D Spanning Tree Protocol
- RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Provides port mirror (Many-to-1)
Quality of Service
2 priority queues on all switch ports
Traffic classification
- Port-based priority
- IEEE 802.1p-based priority
- IP TOS / DSCP-based priority
- TCP / UDP port-based QoS
Strict priority and Weighted Round Robin (WRR) CoS policies
9
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Multicast
Supports IGMP Snooping v1 and v2
Security
Physical port to MAC address binding
TCP/UDP port number filter: Forwarding or discarding typical network applications
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Management
Switch Management Interfaces
- Web switch management
- SNMP v1 switch management
Supports DHCP Option82 and DHCP Relay
Firmware upload/download via HTTP
Hardware reset button for system reboot or reset to factory default
PLANET smart discovery utility
10
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Hardware Specifications
Dimensions (W x D x H) 330 x 155 x 43.5 mm, 1U height 440 x 200 x 44.5 mm, 1U height
System:
Power (Green)
10/100BASE-TX PoE+ RJ45 Interfaces
10/100Mbps LNK/ACT (Green)
PoE In-Use (Orange)
LED 10/100/1000BASE-T RJ45 / SFP Interfaces
LNK/ACT (Green)
100/1000 (Green)
PoE Usage
30W, 60W, 90W, 120W (Orange) of FGSD-1008HPS
50W, 100W, 150W, 190W (Orange) of FGSW-1816HPS
Power Consumption Max. 150 watts / 511BTU Max. 240 watts / 816 BTU
11
User’s Manual of FGSD / FGSW Web Smart PoE Switch
PoE Power Output Per port 52V DC, max. 30.8 watts
Layer 2 Functions
Display each port’s speed duplex mode, link status, flow control status, auto
Port Status
negotiation status
TX / RX / Both
Port Mirroring
Many-to-1 monitor
PoE Setting PoE Status / PoE Port Setting / PoE Sequential / PoE Schedule
Management Functions
Standards Conformances
12
User’s Manual of FGSD / FGSW Web Smart PoE Switch
1000BASE-SX :
Cable 50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (varying on
Fiber-Optic SFP module)
Cable 1000BASE-LX :
9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/60/70/120
kilometers (varying on SFP module)
Environment
Temperature: 0 ~ 50 degrees C
Operating
Relative Humidity: 5 ~ 95% (non-condensing)
FGSW-2624HPS / FGSW-2624HPS4
Hardware Specifications
FGSW-2624HPS: TBD kg
Weight
FGSW-2624HPS4: TBD kg
13
User’s Manual of FGSD / FGSW Web Smart PoE Switch
System:
Power (Green)
10/100BASE-TX RJ45 Interfaces (Port1 to Port24):
10/100Mbps LNK/ACT (Green)
PoE In-Use (Orange)
LED 10/100/1000BASE-T RJ45 / SFP Interfaces (Port25 to Port26):
LNK/ACT (Green)
100/1000 (Green)
PoE Usage
50W, 100W, 150W, 190W (Orange) of FGSW-2624HPS
100W, 200W, 300W, 350W (Orange) of FGSW-2624HPS4
PoE Power Output Per Port 56V DC, Max. 30.8 watts
Layer 2 Functions
Display each port’s speed duplex mode, link status, flow control status, auto
Port Status
negotiation status and trunk status
TX / RX / Both
Port Mirroring
Many-to-1 monitor
14
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Management Functions
Standards Conformances
1000BASE-SX :
Cable 50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (varying on
Fiber-Optic SFP module)
Cable 1000BASE-LX :
9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/60/70/120
kilometers (varying on SFP module)
Environment
Temperature: 0 ~ 50 degrees C
Operating
Relative Humidity: 5 ~ 95% (non-condensing)
15
User’s Manual of FGSD / FGSW Web Smart PoE Switch
2. INSTALLATION
This section describes the hardware features and installation of the PoE Web Smart Switch on the desktop or rack mount. For
easier management and control of the PoE Web Smart Switch, familiarize yourself with its display indicators, and ports. Front
panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the PoE Web Smart
FGSD-1008HPS
FGSW-1816HPS
FGSW-2624HPS
FGSW-2624HPS4
■ Gigabit TP Interface
10/100/1000BASE-T Copper, RJ45 Twisted-pair: up to 100 meters.
16
User’s Manual of FGSD / FGSW Web Smart PoE Switch
■ Reset Button
On the left side of the front panel, the reset button is designed for rebooting the PoE Web Smart Switch without turning off
and on the power. The following is the summary table of Reset button functions:
The front panel LEDs indicate instant status of port links, data activity and system power, and help monitor and troubleshoot
when needed. Figures 2-2-A ~ 2-2-D show the LED indications of these PoE Web Smart Switches.
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
Lights: Indicates the link through that port is successfully established at 10/100Mbps.
LNK/ACT Green
Blinks: Indicates that the Switch is actively sending or receiving data over that port.
Lights: Indicates the port is providing 52V DC in-line power.
PoE In-Use Orange
Off: Indicates the connected device is not a PoE Powered Device (PD).
17
User’s Manual of FGSD / FGSW Web Smart PoE Switch
LNK/ACT Green Lights Indicates that the Switch is actively sending or receiving data over that port.
PoE Usage
30W Orange Lights to indicate the PoE power consumption has 30W or over.
60W Orange Lights to indicate the PoE power consumption has 60W or over.
90W Orange Lights to indicate the PoE power consumption has 90W or over.
120W Orange Lights to indicate the PoE power consumption has 120W or over.
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
18
User’s Manual of FGSD / FGSW Web Smart PoE Switch
LNK/ACT Green Blinks: Indicates that the Switch is actively sending or receiving data over that port.
Lights. Indicates the port is successfully established at 1000Mbps.
Slow
100/1000 Green Indicates the port is successfully established at 100Mbps.
Blink:
Off: Indicates the port is successfully established at 10Mbps.
LNK/ACT Green Blinks: Indicates that the Switch is actively sending or receiving data over that port.
PoE Usage
50W Orange Lights to indicate the PoE power consumption has equal 50W or over 50W.
100W Orange Lights to indicate the PoE power consumption has equal 100W or over 100W.
150W Orange Lights to indicate the PoE power consumption has equal 150W or over 150W.
190W Orange Lights to indicate the PoE power consumption has equal 190W or over 190W.
System / Alarm
LED Color Function
PWR Green Lights to indicate that the Switch has power.
19
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Lights: Indicates the link through that port is successfully established at 10/100Mbps.
LNK/ACT Green
Blinks: Indicates that the Switch is actively sending or receiving data over that port.
Lights: Indicates the port is providing DC in-line power.
PoE In-Use Orange
Off: Indicates the connected device is not a PoE Powered Device (PD).
LNK/ACT Green Lights. Indicates that the Switch is actively sending or receiving data over that port.
PoE Usage
50W Orange Lights to indicate the PoE power consumption has equal 50W or over 50W.
100W Orange Lights to indicate the PoE power consumption has equal 100W or over 100W.
FGSW-2624HPS
150W Orange Lights to indicate the PoE power consumption has equal 150W or over 150W.
190W Orange Lights to indicate the PoE power consumption has equal 190W or over 190W.
100W Orange Lights to indicate the PoE power consumption has equal 100W or over 100W.
200W Orange Lights to indicate the PoE power consumption has equal 200W or over 200W.
FGSW-2624HPS4
300W Orange Lights to indicate the PoE power consumption has equal 300W or over 300W.
400W Orange Lights to indicate the PoE power consumption has equal 400W or over 400W.
20
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The rear panel of the PoE Web Smart Switch indicates a DC inlet power socket. Figures 2-3-A ~2-3-D show the rear panel of
FGSD-1008HPS
FGSW-1816HPS
■ AC Power Receptacle
For compatibility with electric service in most areas of the world, the PoE Web Smart Switch’s power supply automatically
Plug the female end of the power cord firmly into the receptalbe on the rear panel of the PoE Web Smart Switch. Plug the
other end of the power cord into an electric service outlet and the power will be ready.
21
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The device is a power-required device, which means it will not work till it is powered. If your networks
should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device.
Power Notice: It will prevent you from network data loss or network downtime. In some areas, installing a surge
suppression device may also help to protect your PoE Web Smart Switch from being damaged by
22
User’s Manual of FGSD / FGSW Web Smart PoE Switch
read the following topics and perform the procedures in the order being presented. To install your PoE Web Smart Switch on a
To install the PoE Web Smart Switch on desktop or shelf, please follow these steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom of the PoE Web Smart Switch.
Step 2: Place the PoE Web Smart Switch on the desktop or the shelf near a DC or PoE-in power source, as shown in Figure
2-4.
Figure 2-4 Place the PoE Web Smart Switch on the desktop
Step 3: Keep enough ventilation space between the PoE Web Smart Switch and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1,
Connect the other end of the cable to the network devices such as printer server, workstation or router.
23
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Connection to the PoE Web Smart Switch requires UTP Category 5 network cabling with RJ45 tips. For
Connect the power plug of the power cable to a standard wall outlet.
When the PoE Web Smart Switch receives power, the Power LED should remain solid Green.
To install the PoE Web Smart Switch in a 19-inch standard rack, please follow the instructions described below.
Step 1: Place the PoE Web Smart Switch on a hard flat surface, with the front panel positioned towards the front side.
Step 2: Attach the rack-mount bracket to each side of the PoE Web Smart Switch with supplied screws attached to the package.
Figure 2-5 shows how to attach brackets to one side of the PoE Web Smart Switch.
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the PoE Web Smart Switch, use suitable screws to securely attach the brackets to the
rack, as shown in Figure 2-6.
24
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Step 6: Proceed with steps 4 and 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply power to the
PoE Web Smart Switch.
The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and
hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the PoE Web Smart
25
User’s Manual of FGSD / FGSW Web Smart PoE Switch
PLANET PoE Web Smart Switch supports both single mode and multi-mode SFP transceiver. The following list of approved
Connector
Model Speed (Mbps) Fiber Mode Distance Wavelength (nm) Operating Temp.
Interface
MGB-GT 1000 Copper -- 100m -- 0 ~ 60 ℃
Connector
Model Speed (Mbps) Fiber Mode Distance Wavelength (TX) Wavelength (RX) Operating Temp.
Interface
MGB-LA10 1000 WDM(LC) Single Mode 10km 1310nm 1550nm 0 ~ 60 ℃
26
User’s Manual of FGSD / FGSW Web Smart PoE Switch
It is recommended to use PLANET SFP on the PoE Web Smart Switch. If you insert an SFP
transceiver that is not supported, the PoE Web Smart Switch will not recognize it.
1. Before we connect PoE Web Smart Switch to the other network device, we have to make sure both sides of the SFP
transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX, 1000Bas-LX to 1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male
To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male
2. Connect the other end of the cable to a device with SFP transceiver installed.
3. Check the LNK/ACT LED of the SFP slot on the front of the PoE Web Smart Switch. Ensure that the SFP transceiver is
operating correctly.
4. Check the Link mode of the SFP port if the link fails. To function with some fiber-NICs or Media Converters, user has to set
3. Lift up the lever of the MGB module and turn it to a horizontal position.
27
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Never pull out the module without lifting up the lever of the module and turning it to a
horizontal position. Directly pulling out the module could damage the module and the SFP
28
User’s Manual of FGSD / FGSW Web Smart PoE Switch
3. SWITCH MANAGEMENT
This chapter explains the methods that you can use to configure management access to the PoE Web Smart Switch. It
describes the types of management applications and the communication and management protocols that deliver data between
your management device (workstation or personal computer) and the system. It also contains information about port connection
options.
Requirements
SNMP Access
3.1 Requirements
Workstations running Windows 2000/XP, 2003, Vista/7/8, 2008, MAC OS9 or later, Linux, UNIX or other platforms
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above Workstation is installed with Web browser and JAVA runtime environment plug-in
It is recommended to use Internet Explore 8.0 or above to access PoE Web Smart Switch.
29
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The Web browser management is embedded in the PoE Web Smart Switch software and available for immediate use. Each of
these management methods has their own advantages. Table 3-1 compares the three management methods.
Web Browser Ideal for configuring the switch Security can be compromised (hackers
SNMP Agent Communicates with switch functions Requires SNMP manager software
on the network through a standard browser such as Microsoft Internet Explorer. After you set up your IP address for the switch,
you can access the PoE Web Smart Switch's Web interface applications directly in your Web browser by entering the IP address
30
User’s Manual of FGSD / FGSW Web Smart PoE Switch
You can then use your Web browser to list and manage the PoE Web Smart Switch configuration parameters from one central
location, just as if you were directly connected to the PoE Web Smart Switch's console port. Web Management requires either
Microsoft Internet Explorer 8.0 or later, Google Chrome, Safari or Mozilla Firefox 1.5 or later.
The following web screen based on FGSW-1816HPS will be the same as that of
FGSD-1008HPS and FGSW-2624HPS / FGSW-2624HPS4.
Figure 3-2 Web Main Screen of the PoE Web Smart Switch
Network Manager, HP Openview Network Node Management (NNM) or What’s Up Gold. This management method requires
the SNMP agent on the switch and the SNMP Network Management Station to use the same community string. This
management method, in fact, uses two community strings: the get community string and the set community string. If the
SNMP Network Management Station only knows the set community string, it can read and write to the MIBs. However, if it only
knows the get community string, it can only read MIBs. The default gets and set community strings for the PoE Web Smart
31
User’s Manual of FGSD / FGSW Web Smart PoE Switch
site is an ideal solution. The following installation instructions are to guide you to running the Planet Smart Discovery Utility.
If there are two LAN cards or above in the same administrator PC, choose a different LAN card
by using the “Select Adapter” tool.
3. Press the “Refresh” button for the currently connected devices in the discovery list as the screen shows below:
32
User’s Manual of FGSD / FGSW Web Smart PoE Switch
1. This utility shows all necessary information from the devices, such as MAC Address, Device Name, firmware version and
Device IP Subnet address. It can also assign new password, IP subnet address and description to the devices.
2. After setup is completed, press the “Update Device”, “Update Multi” or “Update All” button to take effect. The meaning
of the 3 buttons above are shown below:
Update Device: use the current setting on one single device.
Update All: use the current setting on whole devices in the list.
The same functions mentioned above also can be found in “Option” tools bar.
3. To click the “Control Packet Force Broadcast” function, it allows you to assign a new setting value to the Web Smart
Switch under a different IP subnet address.
4. Press the “Connect to Device” button and the Web login screen appears in Figure 3-2.
5. Press the “Exit” button to shut down the Planet Smart Discovery Utility.
33
User’s Manual of FGSD / FGSW Web Smart PoE Switch
4. WEB CONFIGURATION
This section introduces the configuration and functions of the Web-based management.
The Web-based Management supports Internet Explorer 8.0. It is based on Java Applets with an aim to reduce network
bandwidth consumption, enhance access speed and present an easy viewing screen.
By default, IE8.0 or later version does not allow Java Applets to open sockets. The user has to
explicitly modify the browser setting to enable Java Applets to use network ports.
The PoE Web Smart Switch can be configured through an Ethernet connection, making sure the manager PC must be set on
For example, the default IP address of the PoE Web Smart Switch is 192.168.0.100, then the manager PC should be set at
192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
If you have changed the default IP address of the PoE Web Smart Switch to 192.168.1.1 with subnet mask 255.255.255.0 via
console, then the manager PC should be set at 192.168.1.x (where x is a number between 2 and 254) to do the relative
http://192.168.0.100
34
User’s Manual of FGSD / FGSW Web Smart PoE Switch
2. When the following login screen appears, please enter "admin" as the default username and “admin” as the password
(unless you have changed these, in which case use your own login details) to log in the main screen of the PoE Web
The following web screen based on FGSW-1816HPS will be the same as that of
FGSD-1008HPS and FGSW-2624HPS / FGSW-2624HPS4.
After entering the username and password, the main screen appears as Figure 4-3.
35
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Now, you can use the Web management interface to continue the switch management or manage the PoE Web Smart Switch
by Web interface. The Switch Menu on the left of the web page let you access all the commands and statistics the PoE Web
For security reason, please change and memorize the new password after this first setup.
to access the PoE Web Smart Switch using the Web browser of your choice. This chapter describes how to use the PoE Web
Main Screen
Main Functions Menu SFP Port Link Status
Copper Port Link Status
Panel Display
The web agent displays an image of the PoE Web Smart Switch’s ports. The Mode can be set to display different information for
the ports, including Link up or Link down. Clicking on the image of a port opens the Port Statistics page.
The port statuses are illustrated as follows:
36
User’s Manual of FGSD / FGSW Web Smart PoE Switch
RJ45 Ports
SFP Ports
Main Menu
Using the onboard web agent, you can define system parameters, manage and control the PoE Web Smart Switch, and all its
ports, or monitor network conditions. Via the Web-Management, the administrator can set up the PoE Web Smart Switch by
selecting the functions those listed in the Main Function. The screen in Figure 4-1-2 appears.
37
User’s Manual of FGSD / FGSW Web Smart PoE Switch
4.2 System
Use the System menu items to display and configure basic administrative details of the PoE Web Smart Switch. Under the
System, the following topics are provided to configure and view the system information: This section has the following items:
■ Password Setting Configure new user name and password on this page.
The System Info page provides information for the current device information. System Info page helps a switch administrator to
identify the hardware MAC address, software version and system uptime. The screens in Figure 4-2-1 appear.
Object Description
Comment Describes the PoE Web Smart Switch. Up to 15 characters is allowed for the
Device Description.
MAC Address The MAC Address of this PoE Web Smart Switch.
38
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Button
4.2.2 IP Configurations
The IP configuration includes the IP Address, Subnet Mask and Gateway. The configured column is used to view or change the
IP configuration. Fill out the IP Address, Subnet Mask and Gateway for the device. The screens in Figure 4-2-2 appear.
Object Description
Subnet Mask Provide the subnet mask of this switch in dotted decimal notation.
Button
39
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This page provides a configuration of the current User name and Password. After the setup is completed, please press “Apply”
button to take effect. Please log in web interface with new user name and password and the screens in Figure 4-2-3 appear.
Object Description
Button
This section provides reset the PoE Web Smart Ethernet Switch to factory default mode, the screen in Figure 4-2-4 appears.
Button
40
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Press the “Factory Default” button to take affect. After finishing the operation, the following screen in Figure 4-2-5 appears,
and please press the “Reboot” button to return back to the Web login screen. After inputting default username and password,
continue the PoE Web Smart Ethernet Switch management.
This section provides firmware upgrade of the PoE Web Smart Ethernet Switch, the screen in Figure 4-2-6 appears. Before
Firmware Update, it will ask for the Password to confirm this procedure.
Object Description
Button
41
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Key-in the password and press the “Update” button to take effect. After pressing the “Update” button, the screen in Figure
4-2-7 appears. The warning message is for double confirmation.
Press the “OK” button for starting the firmware upgrade process and the screen in Figure 4-2-8 appears.
When the following screen appears, press the “Browser” button to find the firmware location administrator PC as the screen in
After finding the firmware location from administrator PC, press the “Update” button to start the firmware upgrade process. The
When firmware upgrade process is completed, the following screen appears. Please press the “continue” button and wait for
system reboot. After the device reboot, use the latest firmware of the PoE Web Smart Ethernet Switch.
42
User’s Manual of FGSD / FGSW Web Smart PoE Switch
1. Recommend using IE 8.0 or FireFox browser tools for firmware upgrade process.
2. Firmware upgrade needs several minutes. Please wait awhile, and don’t power off the PoE Web
4.2.6 Reboot
The Reboot page enables the device to be rebooted from a remote location. Once the Confirm button is pressed, user has to
re-login the Web interface about 60 seconds later. The Reboot Switch screen in Figure 4-2-12 appears and click to reboot the
system.
Press the “Confirm” button to reboot the PoE Web Smart Ethernet Switch. After device reboot is completed, the Web login
screen appears and login for further management.
43
User’s Manual of FGSD / FGSW Web Smart PoE Switch
。 Port Mirroring Set the source and target ports for mirroring
This page displays current port configurations and status. Ports can also be configured here. The table has one row for each
44
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Tx/Rx Ability Indicates the port state operation. Possible statuses are:
Auto-Negotiation Enable and Disable. Being set as Auto, the speed and duplex mode are
negotiated automatically. When you set it as Disable, you have to set the speed
and duplex mode manually
Enable – Start up the Auto negotiation.
Speed Select any available link speed for the given switch port. Draw the menu bar to
select the mode.
10M – Set up 10M Force mode.
Duplex Select any available link duplex for the given switch port. Draw the menu bar to
select the mode.
Full - Force sets Full-Duplex mode.
Pause When Auto Speed is selected for a port, this section indicates the flow control
capability that is advertised to the link partner. When a fixed-speed setting is
selected, that is what is used. The current Rx column indicates whether pause
frames on the port are obeyed. The current Tx column indicates whether pause
frames on the port are transmitted. The Rx and Tx settings are determined by the
result of the last Auto-Negotiation. Check the configured column to use flow
control.
This setting is related to the setting for Configured Link Speed.
Back Pressure Select the back pressure mode of the port. Back pressure mode is used with half
duplex mode to disable ports from receiving messages. Back pressure mode is
enabled by default. The possible field values are:
Enable – Start up the back pressure mode.
Address Learning Switches remember the source hardware address of each frame received on an
interface, and they enter this information into a MAC database called a
forward/filter table.
Enable - Start up the Address Learning.
Select Port No. Select port number for this check box list.
45
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Button
Configure port Mirroring on this page. This function provides the monitoring of network traffic that forwards a copy of each
incoming or outgoing packet from one port of a network Switch to another port where the packet can be studied. It enables the
To debug network problems, selected traffic can be copied, or mirrored, to a mirror port where a frame analyzer can be
The PoE Web Smart Switch can unobtrusively mirror traffic from any port to a monitor port. You can then attach a
protocol analyzer to this port to perform traffic analysis and verify connection integrity.
1. All frames received on a given port (also known as ingress or source mirroring).
2. All frames transmitted on a given port (also known as egress or destination mirroring).
46
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Source Port Frames transmitted / received from these ports are mirrored to the mirroring port.
Button
47
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This page provides the selection of the ingress and egress bandwidth preamble. The Bandwidth Control Setting and Status
Object Description
Port No Select port number for this drop-down list to enable the function.
Speed Base Configure the speed limitation mode. The possible field values are:
Low
Tx/Rx bandwidth limitation (Kbps) = Tx/Rx Rate (0~255) x 32Kbps (Port 1~Port 18)
High
Tx/Rx bandwidth limitation (Kbps) = Tx/Rx Rate (0~255) x 256Kbps (10/100Mbps ports)
Tx/Rx bandwidth limitation (Kbps) = Tx/Rx Rate (0~255) x 2048Kbps (Gigabit ports).
Buttons
48
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
49
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This section introduces detailed settings of Broadcast Storm Control function of PoE Web Smart Ethernet Switch. There is an
unknown unicast storm rate control, unknown multicast storm rate control, and a broadcast storm rate control. These only affect
flooded frames, i.e. frames with a (VLAN ID, DMAC) pair not present on the MAC Address table. The broadcast storm control is
used to block the excessive broadcast packets, the number ranging from 1 to 63. For example, the broadcast storm of the
port1~6 are enabled and threshold is set to 10. The broadcast packets will be dropped when broadcast packets are more than
The Storm Control Global Setting and Information screen in Figure 4-3-6 appears.
Object Description
Valid values are in the range from 1 to 63; Per unit is 50us for Gigabit speed,
Enable Port Select port number for this checkbox list to enable the function.
Button
50
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This page provides an overview of traffic statistics for all switch ports. The Port Statistics screen in Figure 4-3-7 appears.
Object Description
Counter Mode Select displayed counter mode for this drop-down list.
Selection Options:
framing characters.
51
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The total number of events in which packets were dropped due to lack of
resources.
Buttons
52
User’s Manual of FGSD / FGSW Web Smart PoE Switch
4.4 VLAN
A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical
layout. VLAN can be used to combine any collection of LAN segments into an autonomous user group that appears as a single
LAN. VLAN also logically segment the network into different broadcast domains so that packets are forwarded only between
ports within the VLAN. Typically, a VLAN corresponds to a particular subnet, although not necessarily.
VLAN can enhance performance by conserving bandwidth, and improve security by limiting traffic to specific domains.
A VLAN is a collection of end nodes grouped by logic instead of physical location. End nodes that frequently communicate with
each other are assigned to the same VLAN, regardless of where they are physically on the network. Logically, a VLAN can be
equated to a broadcast domain, because broadcast packets are forwarded to only members of the VLAN on which the
Port-based VLAN
Port-based VLAN limit traffic that flows into and out of switch ports. Thus, all devices connected to a port are members of
the VLAN(s) the port belongs to, whether there is a single computer directly connected to a switch, or an entire
department.
On port-based VLAN, NICs do not need to be able to identify 802.1Q tags in packet headers. NICs send and receive
normal Ethernet packets. If the packet's destination lies on the same segment, communications take place using normal
Ethernet protocols. Even though this is always the case, when the destination for a packet lies on another switch port,
VLAN considerations come into play to decide if the packet is dropped by the Switch or delivered.
53
User’s Manual of FGSD / FGSW Web Smart PoE Switch
the entire network (assuming all switches on the network are IEEE 802.1Q-compliant).
VLAN allow a network to be segmented in order to reduce the size of broadcast domains. All packets entering a VLAN will
only be forwarded to the stations (over IEEE 802.1Q enabled switches) that are members of that VLAN, and this includes
VLAN can also provide a level of security to your network. IEEE 802.1Q VLAN will only deliver packets between stations
that are members of the VLAN. Any port can be configured as either tagging or untagging. The untagging feature of IEEE
802.1Q VLAN allows VLAN to work with legacy switches that don't recognize VLAN tags in packet headers. The tagging
feature allows VLAN to span multiple 802.1Q-compliant switches through a single physical connection and allows
Any port can be configured as either tagging or untagging. The untagging feature of IEEE 802.1Q VLAN allows VLAN to
work with legacy switches that don’t recognize VLAN tags in packet headers. The tagging feature allows VLAN to span
multiple 802.1Q-compliant switches through a single physical connection and allows Spanning Tree to be enabled on all
Tag - The act of putting 802.1Q VLAN information into the header of a packet.
Untag - The act of stripping 802.1Q VLAN information out of the packet header.
1. No matter what basis is used to uniquely identify end nodes and assign these nodes VLAN
membership, packets cannot cross VLAN without a network device performing a routing
2. The PoE Web Smart Switch supports IEEE 802.1Q VLAN. The port untagging function can be
used to remove the 802.1 tag from packet headers to maintain compatibility with devices that
are tag-unaware.
3. The PoE Web Smart Switch's default is to assign all ports to a single 802.1Q VLAN named
DEFAULT_VLAN. As new VLAN is created, the member ports assigned to the new VLAN will
be removed from the DEFAULT_ VLAN port member list. The DEFAULT_VLAN has a VID = 1.
54
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The VLAN Basic Information page displays basic information on the VLAN type supported by the PoE Web Smart Switch.
Object Description
VLAN Mode Display the current VLAN mode used by this PoE Web Smart Switch.
Options:
Port-based
The default VLAN mode is “Port-based VLAN” from the VLAN mode. The screen in Figure 4-4-2 appears.
This section introduces detailed information of IEEE 802.1Q VLAN function of PoE Web Smart Ethernet Switch. To execute
“Tag-based VLAN” mode from VLAN mode, press the “Change VLAN mode” button to enable the 802.1Q VLAN function.
One screen in Figure 4-4-3 will appear, asking for confirming the swap VLAN mode.
55
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Press the “Continue” button and the current Port-based VLAN mode will swap to the Tag-based VLAN mode. The Screen in
Figure 4-4-4 will appear.
Object Description
Display the current VLAN mode used by this PoE Web Smart Switch.
VLAN Mode
Options:
Tag-based VLAN
Port-based VLAN
Options:
Options:
Add Tag
Don’t Care
Remove Tag
56
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Buttons
This page introduces detailed information of VLAN Member function of switch. It has two of VLAN Member types, one is for
Port-based VLAN mode and one is for Tag-based VLAN mode. Both Figures 4-4-5 and 4-4-6 show the type of VLAN Member.
Object Description
Select port number for this drop-down list to enable the function.
Port
Buttons
57
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
PVID must be the same as the VLAN ID whose port belongs to VLAN group, or
Enable / Disable the selected port to join its VLAN member group
VLAN Member Port
Buttons
58
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This setting is exclusive to VLAN setting on “VLAN member setting”. When VLAN member setting is updated, multi-to-1 setting
will be void and vice versa. The “disabled port” means the port is excluded in this setting. The function is for Port-based VLAN
only. All ports excluded in this setting are treated as the same VLAN group. Figure 4-4-7 shows the Multi to 1 Setting.
Object Description
Button
59
User’s Manual of FGSD / FGSW Web Smart PoE Switch
enables you to assign various grades of network service to different types of traffic, such as multi-media, video, protocol-specific,
QoS reduces bandwidth limitations, delay, loss, and jitter. It also provides increased reliability for delivery of your data and
allows you to prioritize certain applications across your network. You can define exactly how you want the switch to treat
Assigning priorities to traffic (for example, to set higher priorities to time-critical or business-critical
applications).
Provide predictable throughput for multimedia applications such as video conferencing or voice
Improve performance for specific types of traffic and preserve performance as the amount of traffic
grows.
The QoS page of the PoE Web Smart Switch contains three types of QoS mode – the First-In-First-Out mode,
All-High-before-Low mode or Weighted-Round-Robin mode can be selected. All the three modes rely on predefined fields
within the packet to determine the output queue.
First-In-First-Out Mode –The output queue assignment is determined with first-come, first-served (FCFS) behaviour.
All-High-before-Low Mode - The output queue assignment is determined by the ToS or CoS field in the packets with strict
priority.
Weighted-Round-Robin Mode –The output queue assignment is determined by the ToS or CoS field in the packets with
scheduling discipline policy.
The PoE Web Smart Switch supports eight priority level queues; the queue service rate is based on the WRR (Weight Round
Robin). The WRR ratio of high-priority and low-priority can be set to 4:1 or 8:1 or any.
60
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
61
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
62
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The TCP/UDP Port-based QoS and Information screen in Figure 4-5-3 appears.
63
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Options:
Low - The output queue assignment is determined with low priority mode
High - The output queue assignment is determined with high priority mode
TCP/UDP port QoS Configure QoS Override function for this drop-down list
function Options:
Override
Not Override
Button
64
User’s Manual of FGSD / FGSW Web Smart PoE Switch
4.6 Security
This section is to control the access to the PoE Web Smart Switch, including the MAC Address Filter and TCP/UDP Filter.
TCP/UDP Filter
The MAC Address Filter and Information screen in Figure 4-6-1 appears.
Object Description
Binding Configure MAC address binding function from this drop-down list.
Options:
65
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Enable
Disable
Buttons
Object Description
Function Enable Configure TCP/UDP Filte function for this drop-down list.
Enable
Disable
Port Filtering Rule Configure Port Filtering Rule function for this drop-down list.
Forward- The selected protocol will be forwarded and the other protocols will be
dropped.
Block- The selected protocol will be dropped and the other protocols will be
forwarded.
66
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The egress traffic will be checked whether Port Filter Rule is to drop or to forward
packets
Button
67
User’s Manual of FGSD / FGSW Web Smart PoE Switch
bridges or routers. This allows the switch to interact with other bridging devices in your network to ensure that only one route
exists between any two stations on the network, and provide backup links which automatically take over when a primary link
goes down. The spanning tree algorithms supported by this switch include these versions:
The IEEE 802.1D Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol allow for the blocking of links
between switches that form loops within the network. When multiple links between switches are detected, a primary link is
established. Duplicated links are blocked from use and become standby links. The protocol allows for the duplicate links to be
used in the event of a failure of the primary link. Once the Spanning Tree Protocol is configured and enabled, primary links are
established and duplicated links are blocked automatically. The reactivation of the blocked links (at the time of a primary link
failure) is also accomplished automatically without operator intervention.
This automatic network reconfiguration provides maximum uptime to network users. However, the concepts of the Spanning
Tree Algorithm and protocol are a complicated and complex subject and must be fully researched and understood. It is possible
to cause serious degradation of the performance of the network if the Spanning Tree is incorrectly configured. Please read the
following before making any changes from the default values.
Creates a single spanning tree from any combination of switching or bridging elements.
Creates multiple spanning trees – from any combination of ports contained within a single switch, in user specified
groups.
Automatically reconfigures the spanning tree to compensate for the failure, addition, or removal of any element in
the tree.
The path cost to the root associated with each switch port
STP communicates between switches on the network using Bridge Protocol Data Units (BPDUs). Each BPDU contains the
following information:
The unique identifier of the switch that the transmitting switch currently believes is the root switch
68
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The switch sends BPDUs to communicate and construct the spanning-tree topology. All switches connected to the LAN on
which the packet is transmitted will receive the BPDU. BPDUs are not directly forwarded by the switch, but the receiving switch
uses the information in the frame to calculate a BPDU, and, if the topology changes, initiates a BPDU transmission.
The shortest distance to the root switch is calculated for each switch
A designated switch is selected. This is the switch closest to the root switch through which packets will be forwarded
to the root.
A port for each switch is selected. This is the port providing the best path from the switch to the root switch.
It is to make the root port a fastest link. If all switches have STP enabled with default settings, the switch with the lowest MAC
address in the network will become the root switch. By increasing the priority (lowering the priority number) of the best switch,
STP can be forced to select the best switch as the root switch.
When STP is enabled using the default parameters, the path between source and destination stations in a switched network
might not be ideal. For instance, connecting higher-speed links to a port that has a higher number than the current root port can
cause a root-port change.
The BPDUs take some time to pass through a network. This propagation delay can result in topology changes where a port that
transitioned directly from a Blocking state to a Forwarding state could create temporary data loops. Ports must wait for new
network topology information to propagate throughout the network before starting to forward packets. They must also wait for
the packet lifetime to expire for BPDU packets that were forwarded based on the old topology. The forward delay timer is used to
allow the network topology to stabilize after a topology change. In addition, STP specifies a series of states a port must
transition through to further ensure that a stable network topology is created after a topology change.
Each port on a switch using STP exists is in one of the following five statuses:
Listening – the port is waiting to receive BPDU packets that may tell the port to go back to the blocking state
Learning – the port is adding addresses to its forwarding database, but not yet forwarding packets
Disabled – the port only responds to network management messages and must return to the blocking state first
69
User’s Manual of FGSD / FGSW Web Smart PoE Switch
You can modify each port status by using management software. When you enable STP, every port on every switch in the
network goes through the blocking status and then transitions through the statuses of listening and learning at power up. If
properly configured, each port stabilizes to the forwarding or blocking statis. No packets (except BPDUs) are forwarded from, or
received by, STP enabled ports until the forwarding status is enabled for that port.
2. STP Parameters
consisting of links between one or more switches. The port level constructs a spanning tree consisting of groups of one or more
ports. The STP operates in much the same way for both levels.
On the switch level, STP calculates the Bridge Identifier for each switch and then sets the Root
On the port level, STP sets the Root Port and the Designated Ports.
The following are the user-configurable STP parameters for the switch level:
Bridge Identifier(Not user A combination of the User-set priority and 32768 + MAC
70
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Maximum Age Timer Measures the age of a received BPDU for a 20 seconds
Forward Delay Timer The amount time spent by a port in the 15 seconds
blocking status.
The following are the user-configurable STP parameters for the port or port group level:
Port Cost A value used by STP to evaluate paths – 200,000-100Mbps Fast Ethernet ports
STP calculates path costs and selects the 20,000-1000Mbps Gigabit Ethernet
path 0 - Auto
Port cost 0
as set at the factory; unless, it is absolutely necessary. The user changeable parameters in the Switch are as follows:
71
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Priority – A Priority for the switch can be set from 0 to 65535. 0 is equal to the highest Priority.
Hello Time – The Hello Time can be from 1 to 10 seconds. This is the interval between two transmissions of BPDU packets sent
by the Root Bridge to tell all other Switches that it is indeed the Root Bridge. If you set a Hello Time for your Switch, and it is not
the Root Bridge, the set Hello Time will be used if and when your Switch becomes the Root Bridge.
The Hello Time cannot be longer than the Max. Age. Otherwise, a configuration error will
occur.
Max. Age – The Max Age can be from 6 to 40 seconds. At the end of the Max Age, if a BPDU has still not been received from
the Root Bridge, your Switch will start sending its own BPDU to all other Switches for permission to become the Root Bridge. If it
turns out that your Switch has the lowest Bridge Identifier, it will become the Root Bridge.
Forward Delay Timer – The Forward Delay can be from 4 to 30 seconds. This is the time any port on the
Switch spends in the listening status while moving from the blocking status to the forwarding status.
Port Priority – A Port Priority can be from 0 to 240. The lower the number, the greater the probability the port will be chosen as
the Root Port.
Port Cost – A Port Cost can be set from 0 to 200000000. The lower the number, the greater the probability the port will be
chosen to forward packets.
3. Illustration of STP
A simple illustration of three switches connected in a loop is depicted in the below diagram. In this example, you can anticipate
If switch A broadcasts a packet to switch B, switch B will broadcast it to switch C, and switch C will broadcast it to back to switch
A and so on. The broadcast packet will be passed indefinitely in a loop, potentially causing a network failure. In this example,
STP breaks the loop by blocking the connection between switch B and C. The decision to block a particular connection is based
on the STP calculation of the most current Bridge and Port settings.
Now, if switch A broadcasts a packet to switch C, then switch C will drop the packet at port 2 and the broadcast will end there.
Setting-up STP using values other than the defaults, can be complex. Therefore, you are advised to keep the default factory
settings and STP will automatically assign root bridges/ports and block loop connections. Influencing STP to choose a particular
switch as the root bridge using the Priority setting, or influencing STP to choose a particular port to block using the Port Priority
72
User’s Manual of FGSD / FGSW Web Smart PoE Switch
73
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The switch with the lowest Bridge ID (switch C) was elected the root bridge, and the ports were selected to give a high port cost
between switches B and C. The two (optional) Gigabit ports (default port cost = 20,000) on switch A are connected to one
(optional) Gigabit port on both switch B and C. The redundant link between switch B and C is deliberately chosen as a 100 Mbps
Fast Ethernet link (default port cost = 200,000). Gigabit ports could be used, but the port cost should be increased from the
default to ensure that the link between switch B and switch C is the blocked link.
Object Description
-Disable
-STP
-RSTP
Bridge Priority Controls the bridge priority. Lower numeric values have better priority. The bridge
(0~61440) priority plus the MSTI instance number, concatenated with the 6-byte MAC
74
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Hello Time (1~10 Sec) The time that controls the switch to send out the BPDU packet to check STP
-Default: 2
Max Age (6~40 Sec) The maximum age of the information transmitted by the Bridge when it is the Root
-Default: 20
Forward Delay (4~30 The delay used by STP Bridges to transition Root and Designated Ports to
Sec) Forwarding (used in STP compatible mode). Valid values are in the range 4 to 30
seconds
-Default: 15
-Maximum: 30
Object Description
75
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Button
Object Description
Priority (0~240) Controls the port priority. This can be used to control priority of ports having
-Default: 128
76
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Path Cost Controls the path cost incurred by the port. The Auto setting will set the path cost
(1~200000000) as appropriate by the physical link speed, using the 802.1D recommended
values. Using the Specific setting, a user-defined value can be entered. The path
cost is used when establishing the active topology of the network. Lower path
cost ports are chosen as forwarding ports in favor of higher path cost ports. Valid
Object Description
Button
77
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Aggregation multiplies the bandwidth between the devices, increases port flexibility, and provides link redundancy.
Each LAG is composed of ports of the same speed, set to full-duplex operations. Ports in a LAG, can be of different media types
(UTP/Fiber, or different fiber types), provided they operate at the same speed.
Aggregated Links can be assigned manually (Port Trunk) or automatically by enabling Link Aggregation Control Protocol
Aggregated Links are treated by the system as a single logical port. Specifically, the Aggregated Link has similar port attributes
Static LAGs (Port Trunk) – Force aggregared selected ports to be a trunk group.
Link Aggregation Control Protocol (LACP) LAGs - LACP LAG negotiate Aggregated Port links with other
LACP ports located on a different device. If the other device ports are also LACP ports, the devices establish
78
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner
Systems that require high speed redundant links. Link aggregation lets you group up to eight consecutive ports into a single
dedicated connection. This feature can expand bandwidth to a device on the network. LACP operation requires full-duplex mode,
Port link aggregations can be used to increase the bandwidth of a network connection or to ensure fault recovery. Link
aggregation lets you group up to 8 consecutive ports into a single dedicated connection between any two the Switch or other
Layer 2 switches. However, before making any physical connections between devices, use the Link aggregation Configuration
menu to specify the link aggregation on the devices at both ends. When using a port link aggregation, note that:
The ports used in a link aggregation must all be of the same media type (RJ45, 100 Mbps fiber).
The ports that can be assigned to the same link aggregation have certain other restrictions (see below).
The ports at both ends of a connection must be configured as link aggregation ports.
None of the ports in a link aggregation can be configured as a mirror source port or a mirror target port.
All of the ports in a link aggregation have to be treated as a whole when moved from/to, added or deleted from a
VLAN.
The Spanning Tree Protocol will treat all the ports in a link aggregation as a whole.
Enable the link aggregation prior to connecting any cable between the switches to avoid creating a data loop.
Disconnect all link aggregation port cables or disable the link aggregation ports before removing a port link
It allows a maximum of 8 ports to be aggregated at the same time. The PoE Web Smart Switch support Gigabit Ethernet ports
(up to 8 groups). If the group is defined as a LACP static link aggregationing group, then any extra ports selected are placed in a
standby mode for redundancy if one of the other ports fails. If the group is defined as a local static link aggregationing group,
then the number of ports must be the same as the group member ports.
Use the Link Aggregation Menu to display or configure the Trunk function. This section has the following items:
79
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This page allows configuring Link Aggregation Settings. The Link Aggregation Settings screens in Figure 4-8-2 appears.
Object Description
If the LACP partner wants to form a larger group than is supported by this device
then this parameter will control which ports will be active and which ports will be
Algorithm MAC Address Source: The MAC Address Source can be used to calculate the
80
User’s Manual of FGSD / FGSW Web Smart PoE Switch
MAC Address Source & Destination: The MAC Address Source & Destination
can be used to calculate the port for the frame.
Member Select port number for this drop down list to esatablish Link Aggregation.
LACP: LACP LAG negotiate Aggregated Port links with other LACP ports
located on a different device. If the other device ports are also LACP ports,
Operation Key The Key value incurred by the port, range 1-65535 . The Auto setting will set the
Using the Specific setting, a user-defined value can be entered. Ports with the
same Key value can participate in the same aggregation group, while ports with
Time Out The Timeout controls the period between BPDU transmissions.
Short will transmit LACP packets each second, while Long will wait for 30
Activity The Role shows the LACP activity status. The Active will transmit LACP packets
per second, while Passive will wait for a LACP packet from a partner (speak if
spoken to).
Buttons
81
User’s Manual of FGSD / FGSW Web Smart PoE Switch
The DHCP option 82 enables a DHCP relay agent to insert specific information into a DHCP request packets when forwarding
client DHCP packets to a DHCP server and remove the specific information from a DHCP reply packets when forwarding server
DHCP packets to a DHCP client. The DHCP server can use this information to implement IP address or other assignment
Circuit ID (option 1)
Remote ID (option2).
The Circuit ID sub-option is supposed to include information specific to which circuit the request came in on.
The Remote ID sub-option was designed to carry information relating to the remote host end of the circuit.
The definition of Circuit ID in the switch is 4 bytes in length and the format is "vlan_id" "module_id" "port_no". The parameter of
"vlan_id" is the first two bytes representing the VLAN ID. The parameter of "module_id" is the third byte for the module ID (in
standalone switch it always equals 0; in stackable switch it means switch ID). The parameter of "port_no" is the fourth byte and it
The Remote ID is 6 bytes in length, and the value equals the DHCP relay agent’s MAC address.
This page allows configuring DHCP Relay Agent Settings. The Link Aggregation Settings screens in Figure 4-9-1 appears.
Object Description
DHCP Relay Status Indicates the DHCP relay mode operation. Possible modes are:
82
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Enabled: Enable DHCP relay mode operation. When enabling DHCP relay mode
operation, the agent forwards and transfers DHCP messages between the clients
and the server when they are not on the same subnet domain. And the DHCP
DHCP Relay Hops Configure the DHCP Relay Hops Count Limit settings.
DHCP Relay Option 82 Indicates the DHCP relay information mode option operation. Possible modes
Status are:
Enabled: Enable DHCP relay information mode operation. When enabling DHCP
relay information mode operation, the agent inserts specific information
(option82) into a DHCP message when forwarding to DHCP server and removing
it from a DHCP message when transferring to DHCP client. It only works under
Button
This page allows configuring DHCP Relay Server Settings. The DHCP Relay Server settings screens in Figure 4-9-2 appears.
Object Description
83
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Buttons
This page allows configuring VLAN MAP Relay Agent Settings. The VLAN MAP Relay Agent settings screens in Figure 4-9-4
appears.
Object Description
Object Description
84
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Buttons
85
User’s Manual of FGSD / FGSW Web Smart PoE Switch
central-controlled IP phone system, IP camera system and AP group for the enterprise. For instance, cameras / APs can be
easily installed around the corner in the company for surveillance demands or build a wireless roaming environment in the office.
Without the power-socket limitation, the 8/16/24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart
Ethernet Switch makes the installation of cameras or WLAN APs easier and more efficient.
PD Classifications
A PD may be classified by the PSE based on the classification information provided by the PD. The intent of PD classification is
to provide information about the maximum power required by the PD during operation. However, to improve power management
The PD is classified based on power. The classification of the PD is the maximum power that the PD will draw across all input
A PD will return Class 0 to 4 in accordance with the maximum power draw as specified by Table 4-10-1.
12.95 watts (or to 15.4 watts for AF mode) Mid power or High power
0 Default
25.5 watts (or to 30.8 watts for AT mode)
86
User’s Manual of FGSD / FGSW Web Smart PoE Switch
3~5 watts for un-interrupt power system and power control system.
IP Surveillance
Enterprise, Museum, Campus, Hospital, Bank, can install IP Camera
PoE Splitter
PoE Splitter split the PoE 48V DC over the Ethernet cable into 5/12V DC
3~12 watts power outlet locations, which eliminate the costs for additional AC wiring
High PoE Splitter split the PoE 52V DC over the Ethernet cable into
24/12V DC power output. It frees the device deployment from restrictions
due to power outlet locations, which eliminate the costs for additional AC
3~25 watts wiring and reduces the installation time.
High Power Speed Dome
87
User’s Manual of FGSD / FGSW Web Smart PoE Switch
In a power over Ethernet system, operating power is applied from a power source (PSU-power supply unit) over the LAN
infrastructure to powered devices (PDs), which are connected to ports. Under some conditions, the total output power required
by PDs can exceed the maximum available power provided by the PSU. The system may a prior be planed with a PSU capable
of supplying less power than the total potential power consumption of all the PoE ports in the system. In order to maintain the
The PSU input power consumption is monitored by measuring voltage and current .The input power consumption is equal to the
system’s aggregated power consumption .The power management concept allows all ports to be active and activates additional
ports, as long as the aggregated power of the system is lower than the power level at which additional PDs cannot be
connected .When this value is exceeded, ports will be deactivated, according to user-defined priorities. The power budget is
managed according to the following user-definable parameters: maximum available power, ports priority, maximum allowable
This section allows the user to see the current status of PoE; screen in Figure 4-10-1 appears.
Object Description
Power Supply Budget Configure the total watts usage of PoE Switch.
Status
Consumption
PoE Port 1~8 Display the current operating temperature of PoE chip unit 1.
PoE Port 9~16 Display the current operating temperature of PoE chip unit 2.
88
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This section allows the user to inspect and configure the current PoE port settings as Figure 4-10-2 shows.
Object Description
802.3at mode.
This function wil affect PoE power reservation on Classification power limit mode
only, as 802.3af mode, system is going to reserve 15.4W maximum for PD that
supported Class3 level. As IEEE 802.3at mode, system is going to reserve 30.8
watts for PD that support Class4 level. From class1 to class3 level on the
802.3at mode will be reserved the same PoE power with 802.3af mode.
Priority The Priority represents PoE ports priority. There are three levels of power priority
named 1 (Low), 2 (High) and 3 (Critical).
The priority is used in the case when total power consumption has been over
total power budget. In this case the port with the lowest priority will be turn off,
and offer power for the port of higher priority.
1: Low mode.
2: High mode.
3: Critical mode.
Power Allocation It can limit the port PoE supply watts. Per port maximum value must less than
30.8 watts, total ports values must less than the Power Reservation value. Once
power overload detected, the port will auto shut down and keep on detection
mode until PD’s power consumption lower than the power limit value
Port No. Select the ports to apply the PoE Port Setting
89
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Class Display the class of the PD attached to the port, as established by the
classification process. Class 0 is the default for PDs. The PD is powered based
Table 4-10-1.
Priority The Priority shows the port's priority configured by the user.
Power Used [W] The Power Used shows how much power the PD currently is using.
Power Allocation [W] Display PoE port maximum output value of PoE Port Setting
Button
90
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This page allows the user to configure the PoE Ports started up interval time. PoE delay is to delay power feeding when the
The PoE port will start providing power after the whole system program has finished running.
Object Description
Delay Time (0 ~ 300) Allows user to configure the PoE Port Start Up interval time.
seconds
Port No. Select the ports to apply the Port Sequential function
The PoE Port Sequential Setting Status screen in Figure 4-10-5 appears.
91
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Button
92
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Recovery (PC Allow to recovery current configuration to switch. Use “Browser” button to select
Switch) file which you want to reload to switch and type in the switch password.
Buttons
93
User’s Manual of FGSD / FGSW Web Smart PoE Switch
for feature processing. The overall purpose of IGMP Snooping is to limit the forwarding of multicast frames to only ports that are
Computers and network devices that want to receive multicast transmissions need to inform nearby routers that they will
become members of a multicast group. The Internet Group Management Protocol (IGMP) is used to communicate this
information. IGMP is also used to periodically check the multicast group for members that are no longer active. In the case
where there is more than one multicast router on a sub network, one router is elected as the ‘queried’. This router then keeps
track of the membership of the multicast groups that have active members. The information received from IGMP is then used to
determine if multicast packets should be forwarded to a given sub network or not. The router can check, using IGMP, to see if
there is at least one member of a multicast group on a given subnet work. If there are no members on a sub network, packets
94
User’s Manual of FGSD / FGSW Web Smart PoE Switch
95
User’s Manual of FGSD / FGSW Web Smart PoE Switch
IGMP version 1 is defined in RFC 1112. It has a fixed packet size and no optional data.
Octets
0 8 16 31
Type Meaning
IGMP packets enable multicast routers to keep track of the membership of multicast groups, on their respective sub networks.
The following outlines what is communicated between a multicast router and a multicast group member using IGMP.
A host will never send a report when it wants to leave a group (for version 1).
A host will send a “leave” report when it wants to leave a group (for version 2).
Multicast routers send IGMP queries (to the all-hosts group address: 224.0.0.1) periodically to see whether any group members
exist on their sub networks. If there is no response from a particular group, the router assumes that there are no group members
on the network.
The Time-to-Live (TTL) field of query messages is set to 1 so that the queries will not be forwarded to other sub networks.
96
User’s Manual of FGSD / FGSW Web Smart PoE Switch
IGMP version 2 introduces some enhancements such as a method to elect a multicast queried for each LAN, an explicit leave
The states a computer will go through to join or to leave a multicast group are shown below:
Configure Miscellaneous functions on this page. This section has the following items:
。 Output Queue Aging Time Configure Output Queue Aging Time settings
This page allows configuring Miscellaneous functions Settings. The Miscellaneous functions settings screen in Figure 4-12-5
appears.
97
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Object Description
Aging time(ms) Use higher Output Queue Aging Time will have bad utilization of shared buffer
group or not.
98
User’s Manual of FGSD / FGSW Web Smart PoE Switch
Button
4.13 SNMP
The Simple Network Management Protocol (SNMP) is an application layer protocol that facilitates the exchange of
management information between network devices. It is part of the Transmission Control Protocol/Internet Protocol (TCP/IP)
protocol suite. SNMP enables network administrators to manage network performance, find and solve network problems, and
An SNMP-managed network consists of three key components: Network management stations (NMSs), SNMP agents,
Management information base (MIB) and network-management protocol:
Network management stations (NMSs):Sometimes called consoles, these devices execute management
applications that monitor and control network elements. Physically, NMSs are usually engineering
workstation-caliber computers with fast CPUs, megapixel color displays, substantial memory, and abundant disk
agents and NMSs. SNMP is the Internet community's de facto standard management protocol.
SNMP Operations
SNMP itself is a simple request/response protocol. NMSs can send multiple requests without receiving a response.
1. Get -- Allows the NMS to retrieve an object instance from the agent.
2. Set -- Allows the NMS to set values for object instances within an agent.
3. Trap -- Used by the agent to asynchronously inform the NMS of some event. The SNMPv2 trap message is
designed to replace the SNMPv1 trap message.
SNMP community
An SNMP community is the group that devices and management stations running SNMP belong to. It helps define where
information is sent. The community name is used to identify the group. A SNMP device or agent may belong to more than one
SNMP community. It will not respond to requests from management stations that do not belong to one of its communities. SNMP
Read = public
Configure SNMP functions on this page. This section has the following items:
99
User’s Manual of FGSD / FGSW Web Smart PoE Switch
This page allows configuring SNMP functions Settings. The SNMP functions Settings screen in Figure 4-13-1 appears.
Object Description
Community Name A string identifying the SNMP Community name that this entry should belong to.
Access Right Indicates the SNMP community type operation. Possible types are:
System Descrition A string identifying the System Descrition name that this entry should belong to.
System Contact A string identifying the System Contact name that this entry should belong to.
System Location A string identifying the System Location name that this entry should belong to.
Trap State Indicates the SNMP Trap State operation. Possible types are:
Enable Trap Server Indicates the SNMP Trap Server operation. Possible types are:
Button
100
User’s Manual of FGSD / FGSW Web Smart PoE Switch
4.14 Logout
This page allows enabling Logout Settings. The Logout settings screen in Figure 4-14-1 appears.
Button
101
User’s Manual of FGSD / FGSW Web Smart PoE Switch
5. SWITCH OPERATION
address information of some node in network, including MAC address, port no, etc. This in-formation comes from the learning
5.2 Learning
When one packet comes in from any port, the Switch will record the source address, port no. And the other related information
in address table. This information will be used to decide either forwarding or filtering for future packets.
address learning. The Ethernet Switching will lookup the address-table for the destination address. If not found, this packet will
be forwarded to all the other ports except the port, which this packet comes in. And these ports will transmit this packet to the
network it connected. If found, and the destination address is located at different port from this packet comes in, the Ethernet
Switching will forward this packet to the port where this destination address is located according to the information from address
table. But, if the destination address is located at the same port with this packet comes in, then this packet will be filtered.
5.4 Store-and-Forward
Store-and-Forward is one type of packet-forwarding techniques. A Store-and-Forward Ethernet Switching stores the incoming
frame in an internal buffer, do the complete error checking before transmission. Therefore, no error packets occurrence, it is the
The Ethernet Switch scans the destination address from the packet-header, searches the routing table pro-vided for the
incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for connecting servers
directly to the network, thereby increasing throughput and availability. How-ever, the switch is most commonly used to segment
existence hubs, which nearly always improves overall performance. An Ethernet Switching can be easily configured in any
Ethernet network environment to signifi-cantly boost bandwidth using conventional cabling and adapters.
Due to the learning function of the Ethernet switching, the source address and corresponding port number of each incoming and
outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address
is on the same segment as the source address. This confines network traffic to its respective domain and reduce the overall
The Switch performs "Store and forward" therefore, no error packets occur. More reliably, it reduces the re-transmission rate.
102
User’s Manual of FGSD / FGSW Web Smart PoE Switch
5.5 Auto-Negotiation
The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth
when a connection is established with another network device (usually at Power On or Reset). This is done by detect the modes
and speeds at the second of both device is connected and capable of, both 10BASE-T and 100BASE-TX devices can connect
103
User’s Manual of FGSD / FGSW Web Smart PoE Switch
with data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power
PoE levels, but can operate with category 3 cable for low power levels. Power is supplied in common mode over two or more of
the differential pairs of wires found in the Ethernet cables and comes from a power supply within a PoE-enabled networking
device such as an Ethernet switch or can be injected into a cable run with a mid-span power supply.
The original IEEE 802.3af-2003 PoE standard provides up to 15.4 W of DC power (minimum 44 V DC and 350mA) to each
device. Only 12.95 W is assured to be available at the powered device as some power is dissipated in the cable. The updated
IEEE 802.3at-2009 PoE standard also known as PoE+ or PoE plus, provides up to 25.5 W of power. The 2009 standard
prohibits a powered device from using all four pairs for power. The 802.3af / 802.3at define two types of source equipment:
Mid-Span
Mid-Span device is placed between legacy switch and the powered device. Mid-Span is tap the unused wire pairs 4/5 and 7/8 to
carry power, the other four is for data transmit.
End-Span
End-Span device is direct connecting with power device. End-Span could also tap the wire 1/2 and 3/6.
Power sourcing equipment (PSE) is a device such as a switch that provides (sources) power on the Ethernet cable. The
maximum allowed continuous output power per cable in IEEE 802.3af is 15.40 W. A later specification, IEEE 802.3at, offers
25.50 W. When the device is a switch, it is commonly called an End-span (although IEEE 802.3af refers to it as endpoint).
Otherwise, if it's an intermediary device between a non PoE capable switch and a PoE device, it's called a Mid-span. An
external PoE injector is a Mid-span device.
Powered device
A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP
Phones, and IP cameras. Many powered devices have an auxiliary power connector for an optional, external, power supply.
Depending on the PD design, some, none, or all power can be supplied from the auxiliary port, with the auxiliary port sometimes
acting as backup power in case of PoE supplied power failure.
104
User’s Manual of FGSD / FGSW Web Smart PoE Switch
used).
The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to the
center tap of the isolation transformer without upsetting the data transfer. In this mode of operation the pair on pins 3 and 6 and
the pair on pins 1 and 2 can be of either polarity.
105
User’s Manual of FGSD / FGSW Web Smart PoE Switch
7. TROUBLESHOOTING
This chapter contains information to help you solve your issue. If the PoE Web Smart Switch is not functioning properly, make
sure the PoE Web Smart Switch is set up according to instructions in this manual.
Solution:
Check the cable connection and remove duplex mode of the PoE Web Smart Switch.
■ Some stations cannot talk to other stations located on the other port
Solution:
Please check the VLAN settings, trunk settings, or port enabled / disabled status.
■ Performance is bad
Solution:
Check the full duplex status of the PoE Web Smart Switch. If the PoE Web Smart Switch is set to full duplex and the partner is
set to half duplex, then the performance will be poor. Please also check the in/out rate of the port.
Solution:
1. Check the LNK/ACT LED on the PoE Web Smart Switch.
Solution:
Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to change
duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.
Solution:
AC power cord not inserted or faulty
Check whether the AC power cord is inserted correctly
Replace the power cord if the cord is inserted correctly; check whether the AC power source is working by
106
User’s Manual of FGSD / FGSW Web Smart PoE Switch
APPENDIX A
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden,
necessary. Each port of the Switch supports auto-MDI/MDI-X detection. That means you can directly connect the Switch to any
Ethernet devices without making a crossover cable. The following table and diagram show the standard RJ45 receptacle/
Interface-Cross
1 Tx + (transmit) Rx + (receive)
2 Tx - (transmit) Rx - (receive)
3 Rx + (receive) Tx + (transmit)
4, 5 Not used
6 Rx - (receive) Tx - (transmit)
7, 8 Not used
107
User’s Manual of FGSD / FGSW Web Smart PoE Switch
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color
of straight-through cable and crossover cable connection:
4 = Blue 4 = Blue
6 = Green 6 = Green
1 2 3 4 5 6 7 8
7 = White / Brown 7 = White / Brown
4 = Blue 4 = Blue
6 = Green 6 = Orange
1 2 3 4 5 6 7 8
7 = White / Brown 7 = White / Brown
Please make sure your connected cables are with the same pin assignment and color as the above table before deploying the
108
EC Declaration of Conformity
*Type of Product : 16-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP ComboWeb
Smart Ethernet Switch
*Model Number : FGSW-1816HPS
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC) and Low Voltage Directive 2006/95/EC.
For the evaluation regarding the EMC, the following standards were applied:
*Type of Product : 8-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/ SFP combo Web
Smart Switch
*Model Number : FGSD-1008HPS
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC) and Low Voltage Directive 2006/95/EC.
For the evaluation regarding the EMC, the following standards were applied: