Professional Documents
Culture Documents
De Mineral Izer Manual
De Mineral Izer Manual
Demineralizer
Brand :
24R
Two Stage Deioniser
Operating Instructions
and
Isolate the equipment and turn off the water if the system is not to be used for long periods of
time. See shut down procedures in manual, under Operation.
Any plumbing work to install this equipment should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this equipment should be carried out by a qualified
electrician or competent person.
This equipment is designed to be operated by staff fully trained at the commissioning of the
deioniser. Staff not fully trained or inexperienced should not be allowed to operate the product
controls.
This product should be serviced by Veolia Water Systems via the UK Service Network, and
only genuine Veolia Water Systems spare parts should be used.
This product must not be modified in any way without the express permission in writing from
Veolia Water Systems. Modification could cause failure to the product and create a Health and
Safety Risk.
Care must be taken to ensure that the equipment does not stand on or impede the electrical
supply cable.
Veolia Water Systems Deionisers are designed to be used for treating normal feed waters,
free from iron, manganese, chlorine, suspended solids and any other substances, which may
affect the performance of the unit. Water that is contaminated by petrol, paint, steel or iron
debris, must not be passed through the deioniser.
Following any servicing work the control panel must be closed, as electricity is potentially
hazardous.
Under no circumstances must you open the electrical control panel whilst the equipment is in
operation. Always turn of the equipment before carrying out any examinations. Similarly no
mechanical work such as the removal of a fitting or valve should be undertaken, whilst the unit
is under pressure. The system should be isolated from the main water supply and all feed
pressure pumps, turned off.
Under no circumstances should you attempt to repair the equipment yourself. Repairs carried
out by inexperienced persons may cause injury and more serious malfunctioning. Refer to
Veolia Water Systems Service department. Always insist on genuine Veolia Water Systems
spare parts.
IMPORTANT
z Remove the staples holding the upper packing to the wooden base.
z Withdraw the upper packing vertically to clear the unit without damage and remove packing
pieces.
z Lift the unit clear of the wooden base. Stand the unit on its own feet on an even floor.
z Examine the plant to ensure it is complete as indicated under "Plant Identification", and
inspect for damage. Report any damage to Veolia Water Systems or your local Agent
immediately.
PLANT IDENTIFICATION
Plant Comprising
Two Ion Exchange Vessels )
Control Panel )
Valves )
Conductivity/Resistivity Meter ) Mounted together
Chemical and Rinse Drain Tube ) on frame
(12.7mm outside diameter plastic )
tube - 4 metres) )
Acid Storage Bottle and Tube )
Caustic Storage Bottle and Tube )
Two Adapters )
(9.5mm outside diameter tube x ) In Plastic Bag
3/8" BSP Male) )
Regeneration Sequence Chart ) For easy reference during unit operation
To be provided by customer: )
1. Water Supply Pipework and ) See "Installation"
fittings and drain facilities )
2. Chemicals for Regeneration )
OPTIONAL EXTRAS
The following equipment specified in the raw water pipework (see Fig. 3 under 'Installation')
may be obtained from Veolia Water Systems
z Break Tank comprising a water tank with float valve and/or float switch control, raw water
booster pump and non-return valve, may be supplied.
z Valve Pack (VP1S) comprising three isolating valves, a combined non-return and vacuum
breaking valve and water sample valve (Order Part Number 532 001).
Note: Options above may be required to conform to Local Water Authority Regulations.
z Cartridge Filter
Note: The cartridge filter is required for raw water with a high level of suspended solids and
turbidity.
z Pressure Gauge
Note: Required to monitor inlet water pressure to the unit (see Technical Data for operating
pressures).
INTRODUCTION
The chemical formula for pure water is H20 but as chemical analysis will show, there are many
other substances in local water supplies in addition to hydrogen and oxygen.
The other substances are dissolved minerals that have been picked up by the ground water on
route to rivers and local water works. The minerals do not remain in the water, but precipitate
out on boiler tubes, turbine blades, pipework, central heating systems, in fact on any item of
plant in contact with the water where they will do harm and tarnish or taint the finish of the
process.
It is to overcome the disadvantages of untreated water supplies that the 12R and 24R units
have been designed and developed.
REGENERATION
The ion-exchange process is carried out on a material consisting of small beads (less than
1mm diameter) of synthetic resin. The resin used in the first stage is referred to as Cation
resin and when treated (i.e. regenerated) with hydrochloric acid (HCl) the calcium, magnesium
and sodium (removed by the resin during two stage deionisation), is replaced by hydrogen
ions. The resin used in the second stage is referred to as an Anion resin, and when
regenerated with Caustic Soda (NaOH), the sulphates, chlorides and nitrates, held on the
resin, are replaced by hydroxyl ions. In this manner the dissolved minerals removed by the
resins are dispelled to drain, and the resins 'regenerated' ready for further two-stage
deionisation
The processes of two-stage deionisation and regeneration are summed up in the following
diagram.
The regeneration procedure is carried out manually by operating the valves in a given
sequence as described under 'Operation'.
INTRODUCTION
The work detailed in the following paragraphs must be carried out by a competent plumber,
with reference to the typical installation shown below:
Note: A pressure gauge is important, however, a filter, water meter and flow indicator are
optional equipment. The equipment to prevent back syphonage, that is the vacuum breaking
valve and non-return valve (see ‘Optional Extras’) may be required to conform to Local Water
Authority regulations. Alternatively a break tank may be required.
INITIAL PREPARATION
z Because deionised water can be contaminated easily locate the plant as close as possible
to the point of use of the treated water.
z Hydrochloric acid and sodium hydroxide (caustic soda) used to regenerate the resins are
very corrosive and consequently must be kept out of the way of the public and uninformed
staff.
z A drain capable of handling the 15% solution of acidic and alkaline effluents (see Technical
Data for maximum flows to drain) from the deioniser must be available or constructed within
3 metres of the installation.
z Because of the corrosive nature of the waste effluents, the Local Water Authority must be
consulted before disposal into local rivers, streams or municipal sewers.
z Adequate space to change and manoeuvre the acid and caustic soda storage bottles
(250mm minimum at each side of the unit).
z Access to the rear of the installation is available for maintenance work (250mm minimum).
z Access to the front panel and valves (500mm minimum above the height of the unit and
l000mm minimum in front of the unit).
The overall dimensions of the plant are given in the Technical Data.
WATER PRESSURE
Minimum 1.5 bar
Maximum 7.0 bar
AMBIENT TEMPERATURE
Maximum 30ºC
Minimum 10ºC
Note: The minimum ambient temperature is specified because below 15°C caustic soda
becomes very viscous and starts to freeze, making chemical injection into the unit extremely
difficult. If the ambient temperature is between 10 and 15°C only use caustic soda between
28%-30%.
z The required strength of hydrochloric acid and caustic soda is given in the Technical Data.
z The acid and caustic soda is drawn from the storage bottles by the acid and caustic
injectors which form an integral part of the pipework assembly.
WARNING: Both of these chemicals are corrosive and therefore, chemical goggles, rubber
gloves, boots and protective clothing must be worn when handling and charging the storage
bottles. The operating staff must be properly trained and instructions for first aid and the
handling of spilt chemicals must be displayed in the area. Everyone who handles these
chemicals must be continuously cautious, observant and alert.
PIPEWORK CONNECTIONS
z Supply and fit isolating valves in the raw water and treated water pipework. All treated water
pipework must be made in uPVC, PVC (Polyvinyl chloride), ABS (Acrylonitrile Butadiene
Styrene), polypropylene, stainless steel or suitable lined piping - standard plumbing
materials, such as copper or galvanised piping are not to be used.
z Place the deioniser into position. The valves and conductivity meter on the front panel must
be easily accessible and observable.
Ensure the chemical storage bottles can be removed easily.
z Using the adapters supplied (9.5mm (3/8") outside diameter tube x 3/8" BSP male) connect
the deioniser inlet and outlet tubes (which are labelled "INLET" and "OUTLET") to the raw
water and treated water connections respectively.
To connect the adapter to the plastic tube, release the nut, push tube fully into the fitting
and re-tighten the nut.
z Run the Chemical/Rinse Drain tube to an open drain or gully which is within 4 metres of the
unit.
z If the drain is more than 4 metres from the unit, connect the Chemical/Rinse Drain tube to
the open drain as shown.
Do NOT increase the Chemical/Rinse Drain tube length by attaching more tube.
BATTERY INSTALLATION
z Unscrew retaining screw holding the black rear cover of the Conductivity Meter.
z Fit 9V PP3 or equivalent battery to battery connector studs and slide into holder.
z The only adjustment required is to set the volume of the chemical drawn in the stated times
during regeneration:
The chemical draw adjustment is to be set on the 1st Regeneration of the unit (see
'Operation, Regeneration').
Before the unit is put into the 'Cation Acid Injection' fully tighten the 'ACID CHEMICAL
DRAW ADJUSTMENT VALVE.
SLOWLY open the 'ACID CHEMICAL DRAW ADJUSTMENT VALVE] until the ACID is
drawn from the ACID STORAGE BOTTLE.
Monitor the rate of ACID draw and finely adjust the 'ACID CHEMICAL DRAW
ADJUSTMENT VALVE ' until the ACID is drawn in the time stated.
Repeat for 'Anion Caustic Inject' and the adjustment for the 'CAUSTIC CHEMICAL DRAW
ADJUSTMENT VALVE '.
z Monitor the time in which the ACID and CAUSTIC is drawn on the second regeneration of
the unit.
Re-adjust if necessary.
z Further re-adjustment will be required if the operating conditions of the unit change, for
example 'raw water pressure'.
As the deioniser is supplied with the ion exchange resins in their exhausted form it will require
regeneration prior to being put to service.
z Check the CHEMICAL STORAGE BOTTLES hold sufficient chemicals for a regeneration.
See "Acid and Caustic Soda Storage Bottle Filling”
z The manual regeneration procedure as stated below MUST be carried out sequentially.
Refer to the wall chart provided and diagram for the valve operations.
PROCEDURE
Note: It is important to operate the valves in the sequence specified; especially "Cation : Acid
Injection" and "Anion : Caustic Injection". This avoids pressurising the chemical suction lines,
which is undesirable.
Stop
All valve handles Vertically Downwards.
Chemical Isolating valves CLOSED.
Service:
RETURN Anion Drain Valve - HANDLE to VERTICAL.
ADJUST the Service Valve Handle from VERTICAL to HORIZONTAL. The POSITION
regulates the water flow to SERVICE from zero to maximum.
24R = 15 MINUTES
z When viewed from the Front of the unit the Acid Storage Bottle is on the left and the
Caustic Storage Bottle is on the right. Both bottles are situated at the rear of the unit.
Note: Warning: Both of these chemicals are corrosive and therefore, chemical goggles, rubber
gloves, boots and protective clothing must be worn when handling and charging the storage
bottles. The operating staff must be properly trained and instructions for first aid and the
handling of spilt chemicals must be displayed in the area. Everyone who handles these
chemicals must be continuously cautious, observant and alert.
To remove:
z Unlatch the press-stud and release the retaining strap (ONE BOTTLE AT A TIME).
Unscrew the bottle cap (of the chemical bottle to be filled), remove the draw tube complete
with cap from the bottle.
Remove the bottle from the tray and take to a SAFE area for filling.
Fill the bottle, using a funnel, with the specified chemical.
Reverse actions (a), (b) and (c) to refit the chemical bottle.
z If concentrated chemical is spilt onto the unit paint work during filling, it is recommended the
unit be flushed or hosed with water to clean.
(Note: The deionised water (better than 40 µS/cm) obtained from the unit just prior to
regeneration is of acceptable quality for mixing purposes).
z Mixing:
** Recommended Strength
z Ensure:
z The unit may require a Rinse to drain if it has been left standing or used intermittently as
the water quality may be worse than 30 µS/cm.
When the water quality is below 30 µS/cm (or the required quality) return the unit to the
'STOP' position.
z Use the treated water outlet isolating valve for fine flow adjustment.
BATTERY CHECK
z Press the button with the red symbol:
z A good battery is indicated by the meter needle being in the RED zone.
An exhausted battery is indicated by the meter needle being in the amber or green zones.
Battery requires replacement.
z A typical exhaustion profile of a unit (i.e. quality of water versus quantity of water during a
service run) is shown in the graph below:
From above:
z The quality of water produced by your system will depend on the characteristics of the raw
water supply. Typically, the conductivity will be between 20-25 microsiemens, at
commencement of the service period. This may improve during service but will revert to the
initial conductivity value on exhaustion of the Resin Beds, indicating that regeneration is
required.
The amount of treated water obtained will vary with the quality of the water supply used.
For example when treating water with Total Anions 100 ppm (as CaCO3) the units will produce
5,0m3 to 30μS/cm.
Check that:
Hydraulics:
z The inlet, outlet and plant isolating valves are open.
z Sufficient water pressure is available for correct operation (see Technical Data).
z There is no Ion Exchange resin visible in the plant connecting tubes causing a blockage.
z All valves are in the correct position for 'SERVICE', see 'Operation, Start Up and Shut
Down'.
Check that:
Hydraulics
z The flow has not been stopped for a long period. Rinse as in 'Anion Final/Caustic Rinse'
see 'Operation, Regeneration'.
z The raw water quality has not changed excessively.
z The unit requires regeneration. See 'Operation, Regeneration'.
z The flow is not excessive or below the minimum specified (see Technical Data).
z All valves are in the correct position for 'SERVICE' see 'Operation, Start Up and Shut
Down'.
z It may be found or suspected that there is fouling of the ion exchange resins, especially the
anion. If this is thought to be the case, please contact Veolia Water Systems for advice.
Electrical
z The conductivity cell leads and connectors are dry and fully located.
Check that:
Hydraulics
z The raw water total dissolved solids have not increased excessively.
z The flow is not excessive or below the minimum specified (see Technical Data).
z The preceding regeneration was carried out in the correct sequence and with the correct
chemical volumes/strengths.
z It may be found or suspected that there is fouling of the ion exchange resins, especially the
anion. If this is thought to be the case, please contact Veolia Water Systems for advice.
Electrical
z The conductivity cell leads and connectors are dry and fully located.
Check that:
Hydraulic
z There is above the specified minimum water pressure available for correct operation (see
Technical Data).
z The chemical storage bottles have the specified volumes of chemical for a regeneration.
z The hydraulic injectors are not blocked (see below).
z The valves are in the correct positions, see 'Cation Inject' or 'Anion Inject' under 'Operation,
Regeneration'.
z The 'Chemical Adjustment Valves require adjusting, see 'Commissioning' and/or a blockage
in the chemical draw tube.
z The chemical non-return valves are not blocked.
Check that:
z The hydraulic injectors are not blocked (see below).
z The valves are operated in the correct positions, see 'Operation, Regeneration'.