Professional Documents
Culture Documents
Handbook of Department of Civil Eng.25.08.14
Handbook of Department of Civil Eng.25.08.14
HAND BOOK
Institute of Technology
GURU GHASIDAS VISHWAVIDYALAYA
(A CENTRAL UNIVERSITY)
BILASPUR (C.G.) 495009
2
Civil Engineering Student’s
Handbook
INSTITUTE OF TECHNOLOGY,
GURUGHASIDAS VISHWAVIDYALAYA,
(A Central University)
BILASPUR, C.G. 495009
3
Preface
The Institute of Technology under Guru Ghasidas Vishwavidyalaya (now a Central University
since 15th Jan., 2009), Bilaspur (C.G.), was set up in the year 1997 with an objective of
making available the facilities of quality higher education in the field of Engineering and
Technology to the students of, particularly, the Central region of country where the rural and
tribal population still remain deprived of such facilities. The Institute, remaining fully
conscious of its objectives and responsibilities, is growing towards the level of a centre of
excellence for quality engineering education in the country. Especially, after up-gradation of
the University as a Central University, there has been many fold enhancements in
infrastructural facilities as well as faculty and staff. Today, the Institute has well equipped
laboratories with latest equipment, a good library, adequate computational facilities and
smart E-classrooms needed for ensuring quality in higher education and research. The
mission of the Institute is to create an ambiance in which new ideas, research and
scholarship flourish and to engender the leaders and innovators of tomorrow.
The University campus houses faculties like Arts, Science, Social Science, Humanities, Law
and Management etc, our students get opportunities of studying varied nature of elective
courses from other faculties, and are groomed to work not only with a group of technically
trained people but also with persons having knowledge in different domains of education.
The Institute on an average, admits around 400 students annually for the 4 - year
undergraduate B. Tech programme in seven branches. Admissions are made through Joint
Entrance Examination (JEE) (main) or the entrance examination conducted as per the
directions of MHRD, Govt. of India. Presently, M.Tech. programme is being run by two
departments (Mechanical and Chemical Engineering) and the students who are Graduate
Aptitude Test in Engineering (GATE) qualified get admitted. To keep pace with new
developments and changes in the field of technology, the Institute revises its Undergraduate
and Postgraduate Programmes syllabi from time to time. Institute follows semester system
of teaching (odd- July - December; and even- January – June).
Ours is a student-centric Institution and, therefore, the endeavor is always to ensure that
students are offered the quality and value based education and training so as to create not
only outstanding scientists and engineers but also good citizens.
This booklet contains comprehensive information on the existing Rules and Regulations
governing the B.Tech. Programmes. The students and parents/ guardians are, therefore,
advised in their own interest to get fully familiar with the academic system of the Institute
and rules and regulations. Students’ attention is particularly drawn to the attendance
requirement, regular assessment procedures, conditions of promotion to higher semesters
and grading system, etc.
Thank you for your interest in the Institute of Technology, Guru Ghasidas Vishwavidyalaya,
Bilaspur. We wish all our students a very bright future and successful career.
4
Sl. No Content Page. No.
1 Preface 04
2 Introduction 06
3 Ordinance – 12 08
st
4 Scheme & Syllabus of B.Tech.-1 Year 17
nd rd th
5 Scheme & Syllabus of 2 , 3 & 4 Year 33
6 Code of Conduct for Students 106
7 About Ragging 108
Discipline Among Students in University Examinations 118
7 Important Contact Details. 123
8 Contact Details of Staff and Faculty Members of Civil Engineering 126
Department
5
Introduction:
Institute of Technology:
The Institute of Technology is a prestigious institute of higher learning producing meritorious
students with excellent career growth and universal recognition. The students get the best
of opportunities in the form of highly advanced courses, eminent faculty members, well-
equipped laboratories, library, hostels and immense facilities to excel in research and
development. The selection procedure for students at undergraduate and postgraduate is
highly stringent so that Institute of Technology gets the best brains of India. Highly scientific
and innovative technology is used for teaching and carrying out research activities. Every
year Institute of Technology is enriched by the laurels brought by the faculty members and
6
the students in the form of research publications, projects, fellowships and industrial
exposure.
The Institute awards Bachelors and Masters Degrees in various branches of technology. It
has been making special efforts to recruit talented faculty on a world-wide basis and to
admit bright students from all over the country by a careful selection process through
Central Counseling Board (CCB), Government of India based upon AIEEE merit. The Institute
has about 1600 undergraduate students. We have one of the finest technological libraries
with complete information retrieval system.
The Institute has well established Training & Placement Cell which provides the necessary
facilities to the students for their placements. The Training & Placement Cell of the Institute
will strive to develop itself as one of the best placement centre in our country.
The Institute of Technology is poised to reach heights with its quality research, training,
collaborations, and projects. It has signed MOUs with some reputed organizations like IBM
and IIT Kanpur. The faculty is also involved in research and development and has a number
of publications to their credit and some are under process. Finally Institute of Technology
produces career ready graduates who are immediately employee.
7
ORDINANCE – 12
AMENDED ORDINANCE
GOVERNING THE AWARD FOR THE DEGREE OF
BACHELOR OF TECHNOLOGY
(B. TECH. - 4 YEARS (8 SEMESTERS) DEGREE COURSE)
IN THE SCHOOL OF STUDIES, ENGINEERING AND TECHNOLOGY
GURU GHASIDAS VISHWAVIDYALAYA, BILASPUR (C.G.)
[EFFECTIVE FROM SESSION 2013-14]
1.0 GENERAL
The first degree of four years (Eight Semester) Course in Technology, hereinafter called 4-
year B.Tech degree course, shall be designated as ‘BACHELOR OF TECHNOLOGY’ in
respective Branches. The conduct of the programme and the performance evaluation of B.
Tech. courses are on the basis of percentage of marks earned as well as credit system.
2.0 ADMISSION
The minimum qualification for admission to the first year B. Tech. shall be the passing of
Higher Secondary School Certificate Examination (10+2) scheme with Physics, Chemistry and
Mathematics conducted by Central Board of Secondary Education or any other equivalent
examination from recognized Board or University. The candidate shall be eligible for
admission on the basis of the merit list of Joint Entrance Examination (JEE) (main) or any
other entrance examination decided by Guru Ghasidas Vishwavidyalaya for Admission to B.
Tech. degree course time to time. In general the admission to B. Tech. degree course shall be
governed by the rules of, MHRD, Govt. of India and Guru Ghasidas Vishwavidyalaya.
3.1 A Student shall be required to attend at least 75% of the classes actually held in
the semester which may include theory class, seminars, sessionals/ practicals, as may be
prescribed.
Provided that the Dean of the School concerned on the recommendations of the Head of the
Department may condone the shortage in attendance not exceeding 5% for valid and
convincing reasons.
8
Provided, further that students representing the Institute/University in the extra co-
curricular events be given a extra concession up to 5% attendance, if necessary, in addition
to the relaxation in the attendance requirement as provided above. Such concessions would
be available for the days of actual participation in the event, including journey time, with the
prior approval of the Dean of the Students Welfare.
3.2 A student who does not satisfy the requirement of attendance as per clause 3.1,
he/she will be detained due to shortage of attendance in a particular semester and he/she
will have to repeat the same semester taking re-admission as a regular student in the next
commencing academic session.
4.0 DURATION
The duration of undergraduate (U.G.) degree programmes leading to B. Tech. degree, shall
be normally four years and the maximum duration shall be six years from the date of initial
registration in First year B.Tech. course. If a candidate will not be able to complete the
course in the maximum duration of 6 years then he / she will not be eligible to continue the
course from that point of time itself
If a student does not participate in the academic activities of the School of Studies of
Engineering and Technology of this Vishwavidyalaya for a period exceeding two years he /
she shall neither be permitted to appear in any subsequent examinations nor shall be
admitted or promoted to any semester and he / she shall cease to be a student of B. Tech.
Degree Course. Here participation in academic activity means attending Lectures, Tutorials,
Practicals/Sessionals and such other activities declared as academic activities.
6.0 EXAMINATIONS
6.1 Medium of Instruction/Examination – Medium of instruction and examination
shall be English only.
6.2 Practical/ Sessional Work – The student shall be required to complete the
Laboratory / Drawing / Design / Job preparation and other academic work assigned for that
semester in the session.
6.3 There shall be a full End Semester Examination at the end of each semester
consisting of theory papers, practicals/ sessionals.
9
6.4 Preparation Leave – A preparation leave, as decided by the University time to time
shall precede the End Semester (Main) Examination of each semester.
6.5 There shall be one End Semester Examination (ESE) at the end of each semester
conducted by Guru Ghasidas Vishwavidyalaya. Only those students, who will satisfy the
attendance requirement to be eligible to appear at the End Semester Examination as per
clause 3.0, will be permitted to appear in the End Semester Examination. The examination
will consist of theory papers, laboratory practical/sessional and viva-voce as per the scheme
of examination of that semester. These examinations shall be designated as follows.
a. During First year - I & II sem. B. Tech. Examination
b. During Second year- III & IV sem. B. Tech Examination
c. During Third year - V & VI sem. B. Tech. Examination
d. During Fourth year - VII & VIII sem. B. Tech. Examination
6.6 The semester examination will normally be held in the month of November-
December and April – May in every academic session, or as decided by the University time to
time.
6.7 Supplementary examination will be held only once in a year (for both even and
odd semesters) normally in the month of July/August, or as decided by the University time to
time.
6.8 End Semester Examination time table shall be declared by the Controller of
Examination before the commencement of examination.
7.0 PASSING OF EXAMINATION
10
examiners shall be internal from the concerned department of the Institute of Technology,
or external examiners may also be appointed.
7.1.3 To allot the marks of Internal Assessment (I.A.), there will be one Mid Semester
Examination (M.S.E.) in each theory subject of that semester, apart from Class Tests (CT) and
Assignments.
11
the part of Internal Assessment (IA). Evaluation in End Semester Examination shall be done
internally.
Evaluation of practical/sessional during the semester will form 60% weightage and the End
Semester Examination (ESE) will carry 40% weightage.
Percentage as well as absolute grading system will be followed, in every subject, theory or
practical/sessional. A student will be awarded a Letter Grade, based on his combined
performance of Internal Assessment (IA) and End Semester Examination (ESE). These grades
will be described by letters indicating a qualitative assessment of the student’s performance
through a number equivalent called “Grade Point” (GP) as given below. The following is the
Grade Point pattern. Grade ‘F’ indicates not clearing (passing) of the subject.
Grades will be awarded for every theory and practical/sessional subject separately.
8.3 Absolute Grading System
The Absolute Grading System as explained below will be adopted for theory and
practical/sessional subjects.
GRADE THEORY PRACTICAL/SESSIONAL
+
A 90 ≤ Marks ≤ 100%, 90 ≤ Marks ≤ 100%,
A 80 ≤ Marks < 90%, 82 ≤ Marks < 90%,
+
B 70 ≤ Marks < 80%, 74 ≤ Marks < 82%,
B 60 ≤ Marks < 70%, 66 ≤ Marks < 74%,
+
C 50 ≤ Marks < 60%, 58 ≤ Marks < 66%,
C 40 ≤ Marks < 50%, 50 ≤ Marks < 58%,
F 0 ≤ Marks < 40%, 0 ≤ Marks < 50%,
12
th
Performance of a student in i semester is expressed by [SPI]i which is a weighted average of
course grade points obtained by a student in the semester, and is expressed by
[C G + C G + ..........]i ∑ C jG j
i Ni
[ SPI ]i = 1 1 2 2 = =
[ 1 2
C + C + ..........]i Di
∑ C j
i
th
Where Cj stands for Credit and Gj stands for Grade points corresponding to j subject in a
semester. SPIs will be calculated up to two places of decimal without rounding off. SPI will be
calculated only when a student clears a semester without failing in any subject, theory or
practical/sessional.
This is a weighted average of course grade points obtained by a student for all the courses
taken, since his / her admission to the degree program with 50% weightage of I and II
th
semester marks and 100% for the remaining semesters. Thus, CPI in the i semester with “i”
greater than 2 will be calculated as follows
k =i
0.5 [ N1 + N 2 ] + ∑ N k
[CPI ]i = k =3
k =i
0.5 [ D1 + D2 ] + ∑ Dk
k =3
If a student repeats a course or is declared fail in a subject, then only the grade points
earned in the attempt when he / she cleared the course / subject are counted towards CPI.
CPI will be calculated in every semester along with SPI, so that a student knows his / her
latest CPI.
8.6 Award of Class or Division
8.6.1 The class/division awarded to a student with B. Tech. Degree shall be determined
by the student’s CPI after clearing all the subjects of all the eight semesters, as given below:
13
be based on the integrated performance of the candidate for all the eight semesters as per
clause 8.6.
8.6.3 No student shall be declared to have passed the final B.Tech. course unless he/she
has fully passed all the eight semesters. The results of the eighth semester of those students,
who have not passed examination in any previous semester, will be withheld. Such students
shall be deemed to have passed the final B.Tech. examination in the year in which they pass
/ clear all the subjects of all the eight semesters, within the limit of the prescribed period of
the whole course.
14
the next higher odd semester of the next part (year). However, such provisionally admitted
students will become regular only after passing in all their backlog papers in supplementary
examination, if eligible otherwise.
9.6 If a student fails to clear in the supplementary examination all the backlogs of
theory, practical/sessional subjects of the odd and even semesters, he/she will not be
promoted to the odd semester of the next higher part (year), and such student shall be
treated as ex-student.
9.7 Ex-students, (as per clause – 9.6), shall be required to clear their backlog papers
(theory and or practical/sessional subjects), in the end semester examination of the
corresponding semesters (odd and even) to be conducted next year (in the following
academic session). Such ex-students will be required to deposit the examination fees only.
9.8 If an ex-student fails to clear all remaining backlogs (theory and practical/sessional
subjects) which he/she could not clear as an ex-student in the previous year, he/she will be
allowed to appear in the corresponding examination of odd and even semester examinations
in the next subsequent year as a last chance. Such ex-students will be required to deposit
only examination fees. For example, if a first year student does not clear all the subjects
being ex-student in two consecutive years, he/she will be relieved from the programme at
the end of the semester. As such, as an ex-student, a student will be allowed to appear in
the end semester examination of not more than two academic sessions throughout his/her
B.Tech. programme. At any time during his/her B.Tech. programme, if a student has availed
two number of attempts for appearing in the end semester examination as an ex-student,
for clearing the backlog papers (theory and practical/sessional subjects), he/she will be
relieved from the programme at the end of the semester.
9.9 If a student fails to appear in the practical/sessional examination of a semester due
to unforeseen incident, a makeup end semester practical/sessional examination may be
conducted, if required, strictly on the recommendation of the concerned Head of the
Department, and approval of the Dean (Engineering & Technology).
10.0 BRANCH CHANGE AFTER FIRST YEAR RESULT
Starting from the session 2011-12, students admitted in First Year B. Tech. course of the
Institute of Technology having CPI of 08 or above at the end of their First Year course, are
allowed to change their branch according to merit and subject to the seat availability in the
branch where students want to shift. Only those students will be considered for the branch
change who would have cleared all the subjects of First and Second semesters in the first
attempt itself in the End Semester Examination.
15
11.0 TRANSCRIPT
Transcript will be provided to the students as per the University norms
12.0 INTERPRETATION
In case of any dispute in the matter of interpretation of this Ordinance, the decision of the
Executive Council of the University. shall be final and binding on the students.
14.0 Matters not covered in this Ordinance shall be governed by the relevant ordinance of
the University.
16
Scheme & Syllabus
I- SEM. & II-SEM.
(B.Tech.-1stYear)
17
SCHEMEOF EXAMINATION B.Tech – I Year, Common to All Branches, Course – A, w.e.f.
Session: 2012 - 13
S. Periods / Percentage Credit of %
Subject Grand Total
No. Subjects Week Internal Assesment Credit
Code 1 2 3 4 5 6 Total Credit
L T P M.S.E C.T L.A. Total of E.S.E
Professional
1.
BSH-111 Communication in 3 1 - 20 20 - 40 60 100 4
English
2. BSH-112 Engineering Chemistry 3 1 - 20 20 - 40 60 100 4
3. ME-113 Engineering Mechanics 3 1 - 20 20 - 40 60 100 4
Introduction to 3 1 - 40 60 100 4
4. CSE-114 20 20 -
Computer Programming
5. BSH-115 Engineering Maths - I 3 1 - 20 20 - 40 60 100 4
PRACTICAL
Engineering Chemistry
1. BSH-116 - - 3 - - 30 30 20 50 2
Lab
Engineering Mechanics
2. ME-117 - - 3 - - 30 30 20 50 2
Lab
3. ME-118 Engineering Drawing - - 3 - - 30 30 20 50 2
Total Work Load / week : 29 Total Credit : 26 Total Marks : 650
1: Lectures Hours, 2:Tutorials Hours, 3: Practicals Hours, 4: Mid Semester Exam, 5: Class
Tests (Two), 6: Lab Work Assesment
18
BSH 111 - PROFESSIONAL COMMUNICATION IN ENGLISH
Credits L T P
BSH-111
4 4 1 0
Credits L T P
3
4 3 1 0
[Total 42 h]
Unit – I: Chemical Bonding and Transition Metals (8h)
VSEPR theory, Valance Bond Theory and Molecular Orbital Theory. Structures of
coordination compounds corresponding to coordination numbers up to 6. Geometrical and
optical isomerism.
UNIT – II: Structure and Reactivity of Organic Molecules (8h)
Inductive effect, hyper conjugation, resonance and steric hindrance. Carbocation, carbanion
and Free Radicals. Basic concept of nucleophilic & electrophilic-addition, elimination and
substitution reactions. Mechanisms of the reactions viz., Aldol condensation, Cannizzaro
reaction, Perkin Reaction, Beckmann Rearrangement and Hoffmann rearrangement.
19
UNIT – III: Reaction Dynamics & Electrochemistry (8h)
Thermodynamics of chemical process: Concept of entropy, Chemical potential and
equilibrium, Dynamics of chemical reactions: order of reactions, chain reactions and
photochemical reactions. Basic concept of electrochemistry & corrosion.
UNIT – IV: Polymers and Stereochemistry (8h)
Basic concepts and types of polymers, mechanism of polymerisation, vulcanisation, natural
rubber, Nylon-6, Nylon-6.6., PVC, PET, PS, PE. Stereoregularity in polymers. Conformational
analysis (acyclic and cyclic molecules), geometrical and optical isomerism; E, Z and R, S
nomenclature.
UNIT – IV: Spectroscopy and Chromatography (10h)
Theory and application of UV-visible, Infrared and 1H NMR spectroscopy in organic
compounds. Wood words-Fieser rule for calculating λmax. Basic concept and application of
TLC and column chromatography.
Books recommended:
1. Kalsi, P.S.; “Stereochemistry conformation and Mechanism”, New Age Int. (P), Ltd. New
Delhi, 1997.
2. Puri, B. R.; Sharma, L. R. And Pathania, M. S. “Principals of Physical Chemistry”, Shoban Lal
Nagin Chand & Co.
3. Mukherji, S. M. And Singh, S. P., “Reaction Mechanism in Organic Chemistry” Macmillan
India Ltd., New Delhi 2007. Alberty R.A. and Silbey R. J., "Physical Chemistry", John Wiley &
Sons, Inc., Singapore, 1996.
4. Cotton F.A., Wilkinson G. and Gaus P.L., "Basic Inorganic Chemistry", John Wiley & Sons,
Inc., Singapore, 3rd Ed., 1996.
5. Graham-Solomon T.W., "Fundamentals of Organic Chemistry", John Wiley & Sons, Inc.,
Singapore, 1997.
6. Odian T.W., "Principles of Polymerization", John Wiley & Sons, Inc., New York, 1981.
7. Sykes P., "A Guidebook to Mechanism of Organic Chemistry", Longman Inc., New York,
1981.
8. Dye J.R. r, "Application of absorption Spectroscopy of Organic Compounds", Prentice Hall
of India, 1965.
9. Williams D.H. and Fleming I., "Spectroscopic Methods in Organic Chemistry", Tata McGraw
Hill Edition, New Delhi, 4th Ed., 1988.
10. Atkins P.W., "Physical Chemistry", Oxford Univ. Press, 4th Ed., 1990.
11. Morrison R.T. and Boyd R.N., "Organic Chemistry", Prentice Hall of India, 6th Ed., 1992.
12. Rao C.N.R. and Agarwala U. C., "Experiments in General Chemistry", East-West Press,
New Delhi, 1969.
20
ME 113 - ENGINEERING MECHANICS
Credits L T P
BSH-113
4 3 1 0
21
CSE 114 - INTRODUCTION TO COMPUTER PROGRAMMING
Credits L T P
BSH-114
4 3 1 0
22
BSH-115: ENGINEERING MATHS-I
Credits L T P
BSH-115
4 3 1 0
23
BSH 116 – ENGINEERING CHEMISTRY LAB
Credits L T P
BSH-116
2 0 0 3
1. To determine the Normality and Strength (g/L) of given KMnO4 solution titrating against
standard (N/30) Mohr’s salt solution
2. To determine the Normality and Strength (g/L) of given Ferrous Ammonium Sulphate
solution ‘A’ using standard Ferrous Ammonium Sulphate (N/30) solution ‘B’ taking KMnO4
solution as an intermediate.
3. To determine the concentration of hypo solution (Na2S2O3.5H2O) iodimetrically titration
with given Iodine (N/50) solution
4. To prepare the Urea Formaldehyde resin and calculate the yield.
5. To prepare the Aspirin and calculate the yield.
6. Study of Bomb Calorimeter
7. Study of Cleveland’s Apparatus
8. Find out the Total hardness of given water sample using 0.01M EDTA solution, buffer
solution (pH-10) and EBT as an indicator.
9. Find out the Permanent hardness of given water sample using 0.01M EDTA solution,
buffer solution (pH-10) and EBT as an indicator
10.Find out the Temporary hardness of given water sample using 0.01M EDTA solution,
buffer solution (pH-10) and EBT as an indicator.
11.Determination of dissolved oxygen in the given sample water
12.To determine chloride ion in a given water sample by Argentometric method (Mohr’s
method)
24
ME 117 - ENGINEERING MECHANICS LAB
Credits L T P
ME-117
2 0 0 3
Credits L T P
ME-118
2 0 0 3
25
BSH-121 - ENVIRONMENTAL STUDIES
Credits L T P
BSH-121
4 3 1 0
26
ME-122 ENGINEERING THERMODYNAMICS
Credits L T P
ME-122
4 3 1 0
27
BSH 123 -BASIC ELECTRICAL AND ELECTRONICS ENGINEERING
Credits L T P
BSH-123
4 3 1 0
UNIT 1: - Dc Networks: Kirchoff’s Laws, node voltage and mesh current methods, star-delta
transformation, classification of Network Elements, Superposition theorem, Thevenin and
Norton theorems, maximum power transfer theorem, only independent sources, source
conversion.
UNIT 2: - Single Phase AC Circuits: RMS value, average value, form factor, solution of R,L,C
series and parallel circuits, representation of impedance, phasor diagram, power in complex
notation, series and parallel resonance. Three phase AC Circuits: Delta and star connections,
line and phase quantities, solution of three phase circuits, balanced supply voltage and
balanced load, phasor diagram, measurement of power in three phase circuits.
UNIT 3: - Introduction of Electrical Machines – Faradays’ laws of electromagnetic induction,
Single phase Transformer: Construction, emf equations, rating, phasor diagram on no load
and full load, equivalent circuit, regulation, losses, efficiency, open and short circuit tests.
UNIT 4:- D. C. Machines: Construction, emf and torque equations, classification and
application and characteristics of DC motors, speed control. Single and three phase Induction
Motors: Construction, principle of operation, torque-slip curve, starting of single phase IM,
application of three phase and single phase induction motors.
UNIT 5: - Semiconductor Devices: V-I characteristics of P-N Junction diode, diode
parameters, equivalent circuits, zener diode, working and characteristics,
applications.Rectifiers: Analysis of half wave & full wave rectifier with resistive load,
efficiency, ripple factor, filter circuits,
Suggested Text Books and References:
1. Electrical Technology by B.L.Theraja, volume 1 and 2.
2. Electrical Technology by Ian Mckenzie-Smith and Edward Hughes.
3. Basic Electrical Engineering by I.J.Nagrath (TMH)
4. Fitzrald and Higgonbothom: Basic Electrical Engineering, 5th Edition, MGH.
5. Del Torro, Vincent: Electrical Engineering Fundamentals, 2nd Edition, PHI.
6. Cotton H: Advance Technology, ISSAC Pitman, London.
7. Electronic principles: A. V. Malvino
8. Electronic Devices: Bell
9. Electronic Devices & Circuits: Sanjeev Gupta
10. Electronic Devices & Circuits: Robert. L. Boylestad
28
BSH 124 - ENGINEERING PHYSICS
Credits L T P
BSH-124
4 3 1 0
29
BSH 125 – ENGINEERING MATHS-II
Credits L T P
BSH-125
4 3 1 0
UNIT-1: Linear Algebra: Vector space, Linear dependence and Linear Independence Linear
transformation, Rank & Inverse by elementary transformation, System of Linear equations-
inconsistency, Eigen valve and Eigen vectors, Caley Hamilton theorem and its application to
find inverse.
UNIT-II: Theory of Equations: Polynomial & Polynomial equation, Division Algorithm, roots
of equations, Reminder theorem, Factor theorem, Synthetic division, Fundamental theorem
of Algebra. Multiplication of roots, Reciprocal equations, Symmetric function of the roots,
Descarte’s Rule of sign, Cardon’s Method, Ferrari’s Method Descarte’s Method.
UNIT-III: Vector Calculus: Vector functions, Differentiation of vectors, Velocity and
acceleration, Scalar and vector field, Gradient of Scalar field, Directional derivative,
properties of gradient, Divergence of vector, Point Function, curl of vector point function,
properties of divergence and curl, Integration of vector function, Line integral, Surface
Integral, Green, Gauss theorem and Stoke’s theorem (without proof) and their simple
applications.
UNIT-IV: Complex Number : Complex number and its properties, conjugate complex
number, Standard form of complex number, De Moivre’s theorem, Root’s of complex
number, Exponential function of complex variable, Circular function of complex variable,
Hyperbolic function of complex number, Logarthim of complex number C + iS method of
summation.
UNIT-V: Sequence, Convergent, Divergent, Oscillating sequence, Infinite series, Ratio test,
Root test, Comparison test, Raabe’s Logarithmic test, Couchy’s Root test, Gauss’s Test,
Leibnitz Test Conditionally convergant.
30
BSH 127 - ENGINEERING PHYSICS LAB
Credits L T P
BSH-127
2 0 0 3
List of Experiments
1. To determine the wavelength of sodium light with help of Fresnel’s Bi-prism.
2. To determine the refractive index and dispersive power of the material of prism with the
help of spectrometer.
3. To determine the wavelength of sodium light by Newton’s ring method.
4. To determine the wavelength of sodium light by plane diffraction grating.
5. To demonstrate the diffraction pattern and determine the wavelength of different colors
of mercury light using diffraction grating.
6. To determine the wavelength and number of lines per cm on a diffraction grating using
semiconductor laser diode.
7. To determine the specific rotation of sugar solution with the help of polarimeter.
8. Determine the width of the single slit and diameter of circular aperture using Fraunhofer
diffraction pattern produced by semiconductor laser diode.
9. To determine the Energy band gap (Eg) of a semiconductor material using P-N junction
diode.
10. To determine the e/m ratio by Thomson’s method
11. To study the P-N junction diode characteristics, in forwarded and reverse bias conditions.
12. To study the Zener diode characteristics.
13. To study the characteristics and gain of Transistor in C-B and C-E mode.
14. To study the FET characteristics and determine different parameters.
15.To study the MOSFET characteristics
Text Book's and References
1. Engg. Physics Practical by M. N. Avadhanulu, S. Chand Pub.
2. Unified Practical Physics by R. P. Goyal
3. Engg. Physics Practical by Ruby Das et. al.
4. Engg. Physics Theory & Experiments by S. K. Srivatava, New Age International
31
WS 128 - WORKSHOP PRACTICE
Credits L T P
WS-127
2 0 0 3
Fitting Shop: Preparation of step cutting a job of 5mm thick strip. Preparation of V-notch and
V-groove out of 5mm thick strip. Preparation of male female joint out of 5mm thick strip.
Machine Shop: Job on Lathe with plane turning, facing, chamfering and step cutting
operation. Job on Shaper for finishing two sides of a job. Job on Drilling machine – drilling
holes of size 5mm and 12mm diameter on a job.
Welding Shop: Preparation of Butt joint, Lap joint, T-joint, Corner joint from the given work
piece using arc welding.
Carpentry Shop: Prepare a simple Butt joint, Cross Lap joint, T-Lap joint, T-Hole joint and
Mortise and Tenon joint.
Smithy and Forging Shop: Forging principles, Study of operations like drawing, upsetting,
bending and forge welding.
Foundry Shop: Study of preparation of a mould of one piece pattern on the bench.
Reference books:
i. Workshop Technology by Hajara Choudhary, Vol.-I & II.
ii. Workshop Technology by B.S.Raghuwanshi, Vol.-I & II.
iii. Manufacturing Process by H.S.Bawa, Vol.-I & II.
32
Scheme & Syllabus
(2nd Year to 4th Year )
B.Tech.
(Civil Engineering)
III- SEM. to VIII-SEM.
33
SCHEME of B.TECH.-III- SEMESTER - CIVIL ENGINEERING
WEF : ODD SEMESTER OF SESSION – 2012-2013
EVALUATION SCHEME
COURSE PERIODS
SN SUBJECT SESSIONAL - TA SUB- CREDITS
CODE ESE
L T P IA MSE TOTAL TOTAL
THEORY
ENGINEERING
1 21CE01T 3 1 - 20 20 40 60 100 4
MATHEMATICS - III
2 21CE02T SURVEYING -I 3 1 - 20 20 40 60 100 4
STRENGTH OF
3 21CE03T 3 1 - 20 20 40 60 100 4
MATERIALS
CIVIL ENGG
MATERIALS &
4 21CE04T 3 1 - 20 20 40 60 100 4
CONCRETE
TECHNOLOGY
ENGINEERING
5 21CE05T 3 1 - 20 20 40 60 100 4
GEOLOGY
PRACTICAL
SURVEYING –I FIELD
6 21CE06P - - 3 30 - 30 20 50 2
WORK
MATERIAL TESTING
7 21CE07P - - 3 30 - 30 20 50 2
LAB.
CIVIL ENGINEERING
8 21CE08P - - 3 30 - 30 20 50 2
DRAWING
GRAND TOTAL 15 5 9 190 100 290 360 650 26
34
SCHEME of B.TECH. – V - SEMESTER - CIVIL ENGINEERING
WEF : ODD SEMESTER OF SESSION – 2013-2014
EVALUATION SCHEME
COURSE PERIODS
SN SUBJECT SESSIONAL TA SUB- CREDITS
CODE ESE
L T P IA MSE TOTAL TOTAL
THEORY
STRUCTURAL ANALYSIS
1 31CE01T 3 1 - 20 20 40 60 100 4
- II
DESIGN OF CONCRETE
2 31CE02T 3 1 - 20 20 40 60 100 4
STRUCTURES – I
3 31CE03T FLUID MECHANICS - II 3 1 - 20 20 40 60 100 4
GEO- TECHNICAL
4 31CE04T 3 1 - 20 20 40 60 100 4
ENGINEERING - I
TRANSPORTATION
5 31CE05T 3 1 - 20 20 40 60 100 4
ENGINEERING - II
PRACTICAL
FLUID MECHANICS – II
6 31CE06P - - 3 30 - 30 20 50 2
LAB
GEO- TECHNICAL
7 31CE07P - - 3 30 - 30 20 50 2
ENGINEERING – I - LAB
COMPUTER
8 31CE08P APPLICATIONS IN CIVIL - - 3 30 - 30 20 50 2
ENGG. LAB
GRAND TOTAL 15 5 9 190 100 290 360 650 26
35
SCHEME of B.TECH. – VII - SEMESTER - CIVIL ENGINEERING
WEF : ODD SEMESTER OF SESSION – 2014-2015
EVALUATION SCHEME
COURSE PERIODS
SN SUBJECT SESSIONAL TA SUB- CREDITS
CODE ESE
L T P IA MSE TOTAL TOTAL
THEORY
DESIGN OF CONCRETE
1 41CE01T 3 1 - 20 20 40 60 100 4
STRUCTURES - II
ENVIRONMENTAL
2 41CE02T 3 1 - 20 20 40 60 100 4
ENGINEERING - II
WATER RESOURCES
3 41CE03T 3 1 - 20 20 40 60 100 4
ENGINEERING - II
4 41CE04T ELECTIVE - I 3 1 - 20 20 40 60 100 4
to
5 ELECTIVE - II 3 1 - 20 20 40 60 100 4
41CE22T
PRACTICAL
ENVIRONMENTAL
6 41CE23P - - 3 30 - 30 20 50 2
ENGG.-II - LAB
7 41CE24P MINOR PROJECT - - 3 30 - 30 20 50 2
8 41CE25P SEMINAR - - 3 30 - 30 20 50 2
GRAND TOTAL 15 5 9 190 100 290 360 650 26
36
SCHEME OF B.TECH.- VIII - SEMESTER - CIVIL ENGINEERING
WEF : EVEN SEMESTER OF SESSION – 2014-2015
EVALUATION SCHEME
COURSE PERIODS
SN SUBJECT SESSIONAL - TA SUB- CREDITS
CODE ESE
L T P IA MSE TOTAL TOTAL
THEORY
BRIDGE & TUNNEL
1 42CE01T 3 1 - 20 20 40 60 100 4
ENGINEERING
CONSTRUCTION
2 42CE02T PLANNING & 3 1 - 20 20 40 60 100 4
MANAGEMENT
3 42CE03T ELECTIVE - III 3 1 - 20 20 40 60 100 4
to
4 ELECTIVE - IV 3 1 - 20 20 40 60 100 4
42CE19T
PRACTICAL
CONCRETE STRUCTURES
5 42CE20P - - 3 30 - 30 20 50 2
DETAILING
6 42CE21P MAJOR PROJECT - - 9 90 - 90 60 150 6
7 42CE22P PROFESSIONAL ETHICS - - 3 50 - 50 - 50 2
GRAND TOTAL 12 4 15 250 80 330 320 650 26
37
SEMESTER III
21CE01T: ENGINEERING MATHEMATICS-III
SESSIONAL - TA ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I Functions of a complex variable: Complex variable, function of complex variable,
limit, continuity, and differentiability, of a function of a complex variable. Analytic functions,
Cauchy- Riemann equations, Orthogonal curves, harmonic functions, conformal mapping,
bilinear transformation (Mobius transformation) Cauchy integral theorem, Caucy integral
formula, Cauchy’s inequality Taylor theorem, Laurent’s theorem.
UNIT-II Fourier series and Fourier transform : Periodic function, Fourier series, Dirichlet’s
conditions for a Fourier series. Advantages of Fourier series and determination of Fourier
coefficients, Fourier series of function of periods 2, change of interval, Even Odd functions,
Half range sine and cosine series, practical harmonic analysis, Fourier transformation,
Fourier sine and cosine transform , properties of Fourier transform.
UNIT-III Laplace transformation: Laplace transformation, properties of Laplace
transformation, first shift theorem,Laplace transform of the derivative of f(t), multiplication
and division by t. Unit step function: Laplace transformation of unit function, second
shifting theorem, Laplace transform of function and periodic function. Inverse Laplace
transformation Multiplication by s, division by s, first shifting property, second shifting
property, inverse Laplace transform of derivatives , solution of differencial equations by
Laplace transform
UNIT-IV Correlation & Regression : Scatter diagram , Linear Correlation , Measures of
Correlation . Karl Pearson’s Coefficient of correlation , Limits for correlation coefficients,
Coefficient of correlation for bivariate frequency distribution , Rank correlation , Linear
Regression, Equations to the line of Regression. Regrassion coefficient . Angle between two
lines of Regression .
UNIT –V Theoretical Distributions: Discrete and Continuous probability distribution’s
.Mathematical expectation, Mean and Variance, Moments, Moments generating function,
probability distribution ,Binomial, Poisson and Normal distribution ,Test of siginificance
sassed on chi-square , T,F, and Z distribution degree of freedom , conditions for applying X2
(chi-square) test , student’s test.
REFERENCE BOOKS: 1) Prasad C “ Advanced Engineering mathematics”, 2) Pati T “ Functions
of complex variables”, 3) Dass H.K. “ Advanced Engineering mathematics”, 4) Ray M. “
Mathematics statistics”, 5) Higher Engg. Mathematics by Dr. B.S. Grewal– Khanna
Publishers., 6) Advanced Engg. Mathematics by Erwin Kreyszig – John Wiley & Sons, 7)
Advanced Engg.Mathematics by R.K. Jain and S.R.K. Iyengar – Narosa Publishing House., 8)
Applied Mathematics by P.N.Wartikar & J.N. Wartikar. Vol- II– Pune Vidyarthi Griha
Prakashan,Pune., 9) Applied Mathematics for Engineers & Physicists by Louis A. Pipes- TMH.
38
21CE02T: SURVEYING -I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
39
21CE03T : STRENGTH OF MATERIALS
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1: Simple Stresses -Strain and compound stresses: Types of stresses and strains,
Mechanicals properties, Hooke’s law, stress– strain curve for mild & Cast iron, hardness,
impact strength, Poisson’s ratio, Relation between the elastic moduli & Poisson’s ratio, Bars
subjected to varying loads, Temperature stresses in composite bars, Elongation of bars of
constant and varying sections. Stress at a point. Components of stress in rectangular
coordinates, stresses on an inclined plane, Principal stresses & principle plane, Mohr’s circle
of stresses.
UNIT : Shear Force - Bending Moment and Bending Stress: Shear Force & Bending Moment
diagrams in statically determinate beams loaded with different load combination,
Relationship between Load intensity- Shear Force - Bending Moment, Thrust diagram, Point
of contraflexure, loading diagram & Bending moment diagram from shear force diagram,
beam with internal hinge.
UNIT 3: Shear Stresses in Beams and Slope-Deflections of Beams: Derivation of Shear Stress
formula, assumptions, Shear stresses in symmetrical elastic beam with different sections.
Derivation of differential equation for deflection, Slope & Deflection of Beams by Double
integration method, Macaulay’s method & Moment area method. Propped cantilever.
UNIT 4: Torsion and Columns: Equation of Pure Torsion, Assumptions, Power transmitted,
Stiffness of Shafts, Comparison of Solid & Hollow shaft, Strain energy in Torsion. Stable and
unstable equilibrium, Short columns, Euler’s formula for long columns, Equivalent length,
Limitation of Euler’s formula, Rankine’s formula.
UNIT 5: Thin -Thick Cyl;inders-Spheres and Rivet-welded Connection: Stresses in Thin
Cylinders, Changes in Dimensions of Cylinder, Rivetted Cylinders, Thin Spherical Shells. Thick
Cylinders, Lame’s equation. Riveted Joints, Method of riveting, Types of joints, assumptions
made in analysis of riveted joints, pitch of Rivets, Failure of a Riveted joint, Strength of a
riveted joint, Efficiency of a Joint, Design of Riveted joints for axial load. Welded connection,
Types of joints, strength of joints, size of weld, comparison of welded & Riveted joints.
TEXT BOOKS: Strength of Materials – R.K. Rajput (S. Chand & Co.)
NAME OF REFERENCE BOOKS:
Mechanics of Structures (Vol. – I) – Junarkar (Charotar Publications)
Strength of Materials – Timoshenko, S. & Gere (CBS Publishers)
Introductions to Solid Mechanics –Shames & Pitarresi (Prentice Hall of India)
Engineering Mechanics of Solid – Popov (Pearson Publication)
Strength of Materials–S. Ramamurtham (Dhanpat Rai Publications)
Strength of Materials (Part-I) – Timoshenko (CBS Pubishers)
40
21CE04T: CIVIL ENGG. MATERIALS & CONCRETE TECHNOLOGY
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
41
21CE05T : ENGINEERING GEOLOGY
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1:Engineering Geology: Ground water, zones of ground water, water table and perched
water table, water bearing properties of rocks, occurrence of ground water, springs,
selection of a site for well sinking and ground water investigations. Minerals : Minerals, their
physical properties, optical properties and chemical properties.The detailed study of certain
rock forming minerals with respect to the physical properties.
UNIT 2: Structural geology: Strike and dip, out crops, volcanoes, overlaps, inliers and outliers,
types classification of folds, faults, joints, unconformities. Rocks and Rock deformation :Their
origin, structure, texture, classification of rocks in brief and their suitability as Engineering
materials, dip and strike of bed, Folds, Faults, joints, unconformity and their classification,
causes and relation to engineering bahaviour of rock masses.
UNIT 3: Earthquake: Classification, causes and effects of earthquakes and land slides,
seismic curve, seismographs, seismograms, accelograms, seismic problems of India, seismic
zones of India, remedial measures to prevent damage for engineering structures, case
histories. Landslides and Land subsidence : Landslides, its causes, classification and
preventive measures, land subsidence, its causes and preventive measures
UNIT 4: Geological investigation: Interpretation of geological maps, use of aerial maps in
geological surveying, geophysical methods as applied to civil engineering for subsurface
analysis (Electrical and Seismic methods). Engineering Geological Sites Selection :Engineering
Geological considerations for site selection of Dams and Reservoirs, Tunnels, Bridges and
Highways, Geological Maps, concept of geological maps, important terminology used for
map and making a section from the map
UNIT 5: Geology of dams and reservoirs: Types of dams, requirements of dam site,
preliminary and detailed geological investigations for a dam site, important international and
Indian examples of failures of dams and their causes, factors affecting seepage and leakage
of the reservoirs and the remedial measures, silting of reservoirs. Rock mechanics and
tunneling: Purposes of tunneling and geological problems connected with tunneling,
geological considerations in road alignment, roads in complicated regions, problems after
road construction, geology of bridge sites.
NAME OF TEXT BOOKS: 1) A Textbook of Geology – Mukherjee P.K. (World Press Publishers), 2)
Engineering Geology – D.S. Arora (Mohindra Capital Publisher, Chandigarh)
Engineering Geology : Parbin Singh, 3) Structural Geology : H.P. Billings
NAME OF REFERENCE BOOKS: Geology and Engineering – Leggot, R.F. (Mc-Graw Hill, New York),
2) A Geology for Engineers – Blyth, F.G.M. (Arnold, London), 3) Civil Engineering Geology – Cyril
Sankey Fox (C. Lockwood and son, U.K.), 4) Engineering and General Geology – Prabin Singh
(Katson Publication House)
42
21CE06P: SURVEYING –I FIELD WORK
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
Minimum 10 experiments to be performed
1. Linear measurement & offsetting using metric chain.
2. Determination of the area of the given field by cross staff survey.
3. Compass open traversing using prismatic compass and elimination of local attraction.
4. Compass closed traversing using prismatic compass and elimination of local attraction
by bowditch method.
5. To find the difference in elevation between the two non intervisible stations by the
method of differential levelling.
6. To draw longitudinal sectional profile of the road by the method of profile levelling.
7. To draw cross-sectional profile of the road by the method of profile levelling.
8. Contour and its plotting by grid method.
9. Measurement of horizontal angle by repetition method.
10. Measurement of horizontal angle by reiteration method.
11. Traversing of the given area by radiation method using plane table survey.
12. Traversing of the given area by intersection method using plane table.
43
21CE08P: CIVIL ENGINEERING DRAWING.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
Minimum 10 experiments to be performed
1. Graphical Symbols: Doors, Windows, Drains, Pipes, Sanitary, Plumbing, Alphabetical,
Fitment, Electrical fitting symbols
2. To draw the foundation details of internal walls of load bearing structure showing all
detail.
3. To draw the foundation details of external walls of load bearing structure showing all
detail.
4. To draw the single line plan of a single storey residential building.
5. To draw the doble line plan, elevation and section of single story residential building.
6. To draw the single line plan of a primary school building.
7. To draw the single line plan of a primary health centre building.
8. To draw the doble line plan, elevation and section of a primary health centre building.
9. To draw section and elevation of flush shutter, paneled shutter doors and windows.
10. To draw section and elevation of fully glazed, half glazed, half glazed and half paneled
doors and windows.
11. To draw king post truss showing all detail.
12. To draw Queen post truss showing all detail.
13. To draw the two point perspective view of simple blocks.
14. To draw the two point perspective view of stepped blocks.
Recommended Books:
A course in Civil Engineering Drawing – V.B. Sikka (Katson Technical Publications)
Civil Engineering Drawing – Shah, Kala and Patki (Tata McGraw Hill)
44
SEMESTER IV
22CE01T: STRUCTURAL ANALYSIS-I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: Principle of superposition, virtual work principle, Maxwell reciprocal theorem,
deflection of beams using conjugate beam method. Deflection of beams and truss using
energy method (Castigliano theorem), Analysis of plane truss using tension coefficient
method (determinate),
UNIT-II:Three-hinged Arches: Bending Moment, Shear force, axial force for three-hinged
arches, Analysis of Suspension bridge without stiffening girders.
UNIT-III: Influence Lines: Basic concept of moving load and influence line; influence lines for
reactions, Shearing for.es and bending moments for determinate beams; absolute maximum
shearing force and bending moment.
UNIT-IV: Influence lines for three-hinged arches and stresses in simply supported plane
determinate trusses
UNIT-V: Static and kinematic indeterminacy of structure, Method of structural analysis,
Analysis of fixed beam, continuous beam using Theorem of three moments Effect of yielding
of supports.
REFERENCE BOOK:
Elementary structural Analysis by A.K. Jain
Advanced Structural Analysis by A. K. Jain
45
22CE02T : TRANSPORTATION ENGINEERING - I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1: Introduction: Importance of highway transportation, Modes of transportation,
characteristics of highway transport. Historical development & planning: Historical
development of roads, Road development and planning in India, Necessity of planning,
Roads classification, patterns, Planning surveys. Highway alignment and surveys: Engineering
Surveys for highway location Maps and Drawing. Highway drainage: Importance, Surface and
subsurface drainage.
UNIT 2: Geometric Design: Cross Section elements, Sight Distance, Design of horizontal and
vertical Alignment.
UNIT 3: Traffic Engineering: Traffic characteristics, studies such as volume, Speed, ‘O’ and ‘D’
and their uses, Traffic operations, Traffic control devices and prevention of road accidents
Design of Intersections and parking facility, highway lighting, Traffic planning and
administration.
UNIT 4: Highway Materials: Behavior of highway materials, properties of Subgrade and
pavement component materials. Tests on subgrade soil, Aggregate and bituminous
materials. Pavement Design: Factors in design of flexible and rigid pavements, Design of
flexible pavements: Group index, C. B. R. methods, I.R.C. recommended method, Design of
Rigid pavement: Westergaard’s analysis of wheel loads. Stresses in rigid pavements. I.R.C.
recommendations Pavement Construction Techniques and Quality Control: Types of
Pavements water bound macadam, bituminous and cement concrete pavements. Joints in
cement concrete pavements, Pavement failures
UNIT 5: Airport Planning: Definition of terms related to airport engineering, factors affecting
site selection, obstructions, various surveys for site selection, zoning laws. Classification of
Obstructions. Runways: Orientation, Basic runway length and its corrections. Geometric
design, runway configuration taxiways layout geometric, Standards, exit taxiways fillets
separation.
NAME OF TEXT BOOKS: Principle and Practices of Highway Engineering – Kadiyali & Lab
(Khanna Publishers, Delhi)
Highway Engineering – S. K. Khanna & C.E.G. Justo (Khanna Publishers, Delhi)
Air-port planning and Design – Khanna and Arora (Khanna Publishers, Delhi)
Highway Engineering – Rangawala S.C. (Charotar Publishers)
A textbook of Transportation Engineering – S.P. Chandola (S. Chand)
Transportation Engineering – A.K. Upadhyay (S.K. Kataria & Sons)
NAME OF REFERENCE BOOKS: Specifications for Road and Bridge Works – MOST (IRC
Publishers) Manual for Survey, Investigation and Preparation of Road Projects – IRC
Publication 2001.
46
22CE03T SURVEYING - II
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
47
22CE04T : FLUID MECHANICS - I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1: Introduction: Fluid, physical properties of fluids ideal and real fluid, Newtonian and
Non-Newtonian Fluid Fluid Statics: Pressure density height relationship, pressure
measurement by Manometers, Pressure on plane and curved surfaces, centre of pressure,
buoyancy, stability of immersed and floating bodies, metacentric height.
UNIT 2:Kinematics of fluid flow : Steady and unsteady flow, uniform and non uniform flow,
laminar and turbulent flow, one, two and three dimensional flow, streamlines and path
lines, rotational and irrotational flow, continuity equation, three dimensional continuity
equation. velocity potential and stream function.
UNIT 3: Dynamics of fluid flow: Euler’s equation of motion along a streamline and its
integration, Bernoulli’s equation and its applications – Pitot tube, Venturimeter,
orificemeter, problems related to application of momentum equations.
UNIT 4:Flow in Pipes: Major and minor losses in pipe lines, loss due to sudden contraction &
expansion, Pipes in series and parallel Flow in open Channel: Comparison between open
channel and pipe flow, definition of uniform and non-uniform flow, Chezy’s and Manning’s
Formula, Hydraulically efficient channel section of rectangular, trapezoidal.
UNIT 5: Flow through mouthpieces and orifices: Hydraulic coefficients of orifice, flow
through large rectangular orifice, mouthpieces, Borda's mouthpieces. Notches and Weirs:
Rectangular, triangular and trapezoidal notches and weir, cippoletti and broad crested weir.
NAME OF TEXT BOOKS:
Fluid Mechanics and Machines – Dr. A.K. Jain (Khanna Publications)
Fluid Mechanics and Machines – Dr. R.K. Bansal (Laxmi Publications)
Fluid Mechanics & Hydraulic Machines – Dr.P.N.Modi & S.M.Seth,(Narosa Publishing House)
NAME OF REFERENCE BOOKS:
Mechanics of Fluid – Irving H. Shames (McGraw Hill)
Introduction to Fluid Mechanics – James A. Fay (Prentice Hall India)
Fluid Mechanics – R.J. Garde (New Age International Publication)
Fluid Mechanics – Streeter V.L. & Wylie E.B. (Tata McGraw Hills)
Fluid Mechanics – John F Dougles (Pearson Publication)
Introduction to Fluid Mechanics Fox, R.W. and McDonald, A.T., John Wiley & Sons.
Fluid Mechanics”, Streeter, V.L. and Benjamin, W.E., “McGraw-Hill.
Fluid Mechanics and Fluid Mechanics Som, S.K. and Biswas, G.,Tata McGraw Hill.
Introduction to Fluid Mechanics, Fox, R. W. and A. T. McDonald, 6th ed., John Wiley, New
York, (2004)
48
22CE05T : BUILDING CONSTRUCTION
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1: Foundation: Functions of Foundation, essential requirements of a Good Foundation,
Preliminary Investigation of Soil, Bearing Capacity of Soil, Classification of Foundations,
Introduction to Different type of foundation: Masonry footings, isolated footings, Combined
and strap RCC footings, Raft footing, Pile foundations. Friction and Load bearing piles)
UNIT 2: Masonry: Definition of terms used in masonry, Bonds in Brickwork, English Bond,
Flemish Bond, Reinforced brickwork, Joints in Stone Masonry, Rubble Masonry, Coursed
Rubble Masonry, Uncoursed rubble masonry, Random rubble masonry, Ashlar Masonry,
Masonry arches: Classification, Stability of an arch, Lintels, Types and classifications,
Functions, Method of constructions, Chejja, Functions, Method of constructions, Canopy,
Functions, Method of construction, Balcony, Functions, Method of construction,
Shoring,Underpinning,Scaffolding
UNIT 3: Floors and Roofs, Types of flooring (Materials and method of laying),, Granolithic,
Mosaic, Ceramic, Marble, Polished Granite, Industrial flooring, Flat Roof (R.C.C.), Sloped roof
(R.C.C. And Tile roof), Lean to roof, Wooden truss (King post and queen post trusses), Steel
trusses, Weather proof course for RCC Roof,
UNIT4: Stairs, Doors and Windows: Types (Classifications) and Technical terms in stairs,
Requirements of a good stair. Geometric Design of RCC Dog Legged and open well stairs.
(Plan and sectional elevation of stairs), Doors, Types, Paneled doors, Glazed doors, Flush
doors, Collapsible and rolling shutters, Louvered doors, Revolving, sliding and swing doors,
Windows, Types, Paneled, Glazed, Bat window, Dormer window, Louvered and corner
window, Ventilators . Plastering and Painting: Purpose of Plastering, Materials of plastering,
Lime mortar, Cement Mortar Methods of plastering, Stucco plastering, Lath plastering,
Purpose of Painting, Types of Paints, Application of paints to new and old surfaces,
Distemper, Plastic emulsion,, Enamel, Powder coated painting to walls and iron and steel
surfaces, Polishing of wood surface
UNIT5:Introduction to cost effective construction: Necessity, Advantages, Pre fabrication
techniques, Pre cast doors and windows (Pre cast frames, and shutters), Alternative Building
Materials, Hollow concrete blocks, Stabilized mud blocks, Micro concrete tiles, Precast
roofing elements
Miscellaneous topics: Form Work, Form work Details, RCC columns, Beams, Floors, Slip
forming, Damp proof Construction
TEXT BOOKS:
Building Construction by S.G. Rangwala, Charter Publishing House, Anand, India.
Building Construction by Sushil Kumar, Standard Publication and Distributors, New Delhi
Building Construction by Punmia B.C., Lakshmi Publications, New Delhi.
Advanced Building Materials and Construction by Mohan Rai and Jai Sing, CBRI Publications,
Roorkee
49
22CE06P: SURVEYING – II - FIELD WORK.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
50
22CE07P: FLUID MECHANICS –I LAB.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
1. To calculate the total energy at different points and plot the graph between total
energy vs. distance. (Bernoullies Verification of Bernoulli’s equation)
2. To determine the Meta centric height with angle of ship model.
3. To determine the co-efficient of Discharge Cd for Venturimeter
4. To determine the co-efficient of Discharge Cd for Orificemeter.
5. To determine the co-efficient of discharge and to determine the co-efficient of velocity
for Orifice.
6. To determine the co-efficient of discharge and to determine the co-efficient of velocity
for Mouthpiece.
7. To determine the coefficient of discharge Cd of Rectangular Notch.
8. To determine the coefficient of discharge Cd V Notch - 450
9. To determine the coefficient of discharge Cd V Notch - 600
10. To determine the friction factor for Darcy-Weisbach equation
11. Experimental determination of critical velocity in pipe.
51
22CE08P: TRANSPORTATION ENGINEERING – LAB
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
52
SEMESTER V
UNIT-II: Slop Deflection Method: Continuous beams and portals by moment distribution due
to load and yielding of supports.
UNIT-IV: Introduction to Flexibility matrix and Stiffness Matrix methods: Applications of the
methods to simple indeterminate beams.
UNIT-V: Analysis of symmetrical two hinge arches (parabolic and circular). Influence lines for
propped cantilevers, continuous beams using Muller-Breslau’s principle.
REFERENCE BOOK:
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT – I: Introduction to design of concrete structures-limit state analysis and design of
beams for flexure, bond
UNIT- II: Shear and torsion
UNIT-III:one way slabs, stair cases, Two-way slabs
UNIT- IV:Axially and eccentrically loaded columns (uni-axial only)
UNIT-V:Footings – different types of isolated footings, synthesis of limit state and working
Stress methods
REFERENCE BOOK:
Reinforced Concrete Design by Pillai & Menon
Limit State Design of Reinforced Concrete by P.C. Verghese
53
31CE03T : FLUID MECHANICS - II
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1: Turbulent flow in pipe: Nature of turbulence, free and wall turbulence, turbulent
flow in pipes, equation for velocity distribution over smooth and rough surfaces, Colebrook-
White equation, Moody’s diagram, Explicit equation for friction factors.
UNIT 2: Boundary layer Analysis: Boundary layer thickness, boundary layer over a flat plate,
laminar boundary layer, turbulent boundary layer, and laminar sub layer, Application of
momentum equation, local and average friction coefficient. Fluid flow past submerged
bodies. Drag and lift, drag on sphere and cylinder Magnus effect.
UNIT 3:Non-uniform flow in open channel: Specific energy, critical flow, analysis of flow over
hump and transition, equation of gradually varied flow, hydraulic jump and evaluation of its
elements in rectangular channel.
UNIT 4: Compressibility effect in pipe flow: Transmission of pressure waves in rigid and
elastic pipes, water hammer Dimensional analysis and Hydraulic similitude.Dimensional
analysis, Buckingham’s theorem, important dimensionless numbers and their significances,
geometric, kinematics and dynamic similarity, model study.
UNIT 5: Hydraulic Machines: Turbines: Classification of turbines, draft tube, specific speed,
unit quantities, and characteristics curves of turbines, and governing of turbine. Pump:
Introduction, Centrifugal pumps, efficiencies, specific speed, cavitations, slip, percentage slip
NAME OF TEXT BOOKS:
Fluid Mechanics and Machines – Dr. A.K. Jain (Khanna Publications)
Fluid Mechanics and Machines – Dr. R.K. Bansal (Laxmi Publications)
NAME OF REFERENCE BOOKS:
Fluid Mechanics – Dr. P.N. Modi (Standard Book House)
Mechanics of Fluid – Irving H. Shames (McGraw Hill)
Introduction to Fluid Mechanics – James A. Fay (Prentice Hall India)
Fluid Machines – Dr. Jagdish Lal (Metropolitan Book Company Private Ltd.)
Fluid Machines – John P. Douglas (Pearson Publication)
54
31CE04T : GEOTECHNICAL ENGINEERING - I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I:Introduction, Classification of soils, Soil compaction. Effective stresses, Surface
tension and Capillarity
UNIT-II: Permeability of soils, Seepage analysis
UNIT-III:Stress distribution in soils, Compressibility and consolidation, soil compaction
UNIT-IV:Shear strength of soils, Earth pressure theories
UNIT-V:Stability of slopes, Sub-soil exploration, Design principles of shallow and deep
foundation.
REFERENCE BOOK:
Geotechnical Engineering by B. M. Das, Bharat Singh, Samsher Alam
Geotechnical Engineering by S. K. Gulathi & Dutta
Soil Mechanics by Lambe & Whiteman
Soil Mechanics by B.C.Punamia,
55
31CE05T : TRANSPORTATION ENGINEERING - II
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1 Necessity, classification and systems of Railways, Historical Development of
railways in India. Alignment and Survey: Track Alignment, Requirements of good alignment,
Factor affecting alignment, Surveys. Permanent Way: Introduction, Component parts,
Requirement of Permanent Way, Typical Cross-section. Gauge: type & factor affecting.
UNIT 2: Rails: Function, Type, Weight, Selection, Length of rails, Rails joints: type &
requirement, Coning of wheels, Tilting of rails, Roaring of rails, Creep of rails, Wear of rails,
Welding of rails. Sleepers: Requirements of an ideal sleeper, functions, types, sleeper
density. Ballast: Function, characteristics, types, size and section, quantity. Fixtures &
Fastenings: Function, types.
UNIT 3: Geometrics: Terms related to cross section, typical cross section, Gradient, Grade
composition of curves, Curves, Super-elevation, cant deficiency, Negative cant, widening of
gauges on curves.
UNIT 4: Points and Crossings: Necessity, Important technical terms in point and crossings.
Turnout: Component parts and functions. Crossing: Component parts, requirement, types.
Points and switches: Types. Track junctions: Types. Signaling: Object, type. Station & yards:
Introduction, Types of stations, platforms, minimum horizontal, yards level crossing.
UNIT 5: Tunnel Engineering: Consideration in tunneling shape and size, methods of tunnel,
constructions, tunneling in soft soil and rocks, lining of tunnels, ventilations, drainage of
tunnels. Harbour Engineering: Harbour of early period, Dry docks and spillways, warehouses,
Quays, jetties, wharves, piers and berthing facilities, maintenance of ports and harbours.
NAME OF REFERENCE BOOKS:
Railway Engineering – S.C. Saxena & Arora (Dhanpat Rai Publications)
A textbook of Transportation Engineering – S.P. Chandola (S. Chand)
Transportation Engineering – A.K. Upadhyay (S.K. Kataria & Sons)
Tunneling Engineering – S.C. Saxena (Dhanpat Rai Publications)
Railway Engineering – Rangawala (Charotar Publications)
Harbour Engineering – Srinivas
Tunnel and Harbour – Seetharaman S. (Umesh Publications)
56
31CE06P: FLUID MECHANICS – II LAB
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
57
31CE07P: GEO- TECHNICAL ENGINEERING – I - LAB.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
58
31CE08P: COMPUTER APPLICATIONS IN CIVIL ENGG. LAB
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3- 30 - 30 20 50
59
SEMESTER VI
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: Introduction-Building system, Load Path, Loading as per IS 875, load combinations;
Design philosophy-Rolled Sections and Built-up sections; Connections-Welded and Riveted
UNIT-II: Failure Modes; Design of Tension, Compression Members-effective length, buckling
Load
UNIT-III: Design of Flexural Members-Lateral Buckling; Design of Built-up column using lacing
and batten plates. Design of column bases
UNIT-IV:Design of Anchor bolts, Design of plate Girder and Gantry Girder. Industrial
Structures
UNIT-V: Elements of Plastic Design: Introduction, plastic hinges, shape factor, load factor,
collapse loads for beams and portals, effect of axial force and shear on the plastic moment
of the section, uniqueness
REFERENCE BOOKS:
Design of Steel Structures by-S. K. Duggal.
Design of Steel Structures by- B. C. Punmia & A. K. Jain.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: Analysis and design of Shallow Foundations, Foundation failure (Case histories)
UNIT-II: Pile foundations, Foundations on problematic soils
UNIT-III: Shoring and underpinning, Mat foundation
Unit-IV Pier and Caisson foundation, Coffer dam, Diaphragm walls
UNIT-V: Environmental aspects for design/protection of foundation structures .
REFERENCE BOOKS:
Basic & Applied Soil Mechanics. by- Gopal Ranjan & A. S. R. Rao
Foundation Analysis & Design by - J. E. Bowles
60
32CE03T: ENVIRONMENTAL ENGINEERING - I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1:Introduction : Necessity and importance of water supply schemes. Water demand:
Classification of water demands, Estimation of quantity of water required by a town, per
capita demand, factors affecting per capita demand, design period and population
forecasting, variation in water demand. Sources of water supply. Surface sources and
underground sources, Intake works, site selection, type of intake works.
UNIT 2: Quality of water: Common impurities, physical, chemical and biological
characteristics of water, water quality standards for municipal and domestic supplies. Water
Processing: Object of water processing, flow diagrams of typical ground water system and
surface water systems. Sedimentation Theory of sedimentation, sedimentation tanks and its
types, design parameters related with sedimentation tanks, sedimentation with
coagulations, coagulants and coagulant aids, Jar test for determining coagulant dosage.
UNIT 3: Filtration; Theory of filtration, slow sand and rapid sand filters, Construction and
operation. Disinfection, Methods of disinfection, Chlorination, Types of chlorination, Break
Point chlorination.
UNIT 4: Softening: Methods of Softening, Iron Removal, Fluoridisation. Distribution System:
Methods of distribution, layout of distribution system, methods of analysis, pressure in the
distribution system, distribution reservoirs, functions and its types, storage capacity of
distribution reservoir.
UNIT 5: Air Pollution: Introduction, causes, sources, characteristics, effects of air pollution on
plants, humans, animals and materials and atmosphere, air pollution control methods and
equipment. Noise Pollution: Definition, sources, effects of noise pollution on humans,
animals and non-living things, methods of noise control.
NAME OF TEXT BOOKS:
Water Supply Engineering – S.K. Garg (Khanna Publication).
Water Supply Engineering – B.C. Punmia (Laxmi Publication, New Delhi)
NAME OF REFERENCE BOOKS:
Environmental Engineering – Peavy & Rowe (Tata McGraw Hill, New Delhi).
Water Supply and Sanitary Engineering – G.S. Birdi (Dhanpat Rai Publications).
Introduction to Environmental Science – Y. Anjaneyulu (B.S. Publications)
Environmental Science and Engineering – Henry and Heinke (Pearson Education)
61
32CE04T: WATER RESOURCES ENGINEERING - I
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1:Introduction: Need for Irrigation, Advantages and Disadvantages of irrigation, Types
of Irrigation systems – Flow Irrigation, Lift Irrigation. Methods of Irrigation: Introduction,
requirement of irrigation methods, surface and sub surface irrigation. Water Requirement of
Crops: Introduction, Water requirement of crop, crop season and crops of India, crop period
and base period, delta, duty of water, relationship between delta duty and base period,
factors affecting duty.
UNIT 2: Canal Irrigation: Classification of canal, parts of canal irrigation system, canal
alignment, typical canal cross section, command areas, losses in irrigation systems. Design of
Stable Channels in Alluvium. Introduction, Kennedy’s silt theory, Lacey’s Theory, Lacey’s
regime equations, Lacey’s shock theory, Design of channels by Kennedy’s and Lacey’s
theories, maintenance of Irrigation channels.
UNIT 3: Water Logging and its Control. Causes and ill effects of water logging, prevention
and control, reclamation of water logged lands, surface drainage. Design of Lined Channels.
Introduction, benefits of lining, types of lining, economics of lining, procedure and design of
lined canals.
UNIT 4: River Behavior, Control and Training. Objects, river characteristics, river patterns,
classification of river training works, methods of river training embankments, bank
protection, cutoffs, meandering causes and parameters. Flood Control; Introduction, levees
and embankments, channel improvement, flood ways evacuation and flood plain zoning,
National Policy of floods.
UNIT 5: Reservoir Planning: Introduction, Type of reservoirs, storage zones of a reservoir,
mass curve and demand curve, determination of reservoir capacity, safe field. Flood Routing:
Flood Routing principle, inflow storage discharge method, reservoir losses, reservoir,
sedimentation, life of reservoir,
NAME OF TEXT BOOKS:
Irrigation Engineering and Hydraulic Structures – S.K. Garg (Khanna Publications)
Irrigation Engineering – B.C. Punmia (Laxmi Publications)
NAME OF REFERENCE BOOKS: Irrigation, Water Resources and Water Power Engineering –
Dr. P.N. Modi (Standard Book House)
Theory and Design of Irrigation Structures (Volume – I & II) – Varshney (Nem Chand & Bros.)
Irrigation and Water resources Engineering – Asawa G.L. (New Age International
Publications)
Fundamentals of Irrigation Engineering – Bharat Singh (Nem Chand & Bros)
Water Resources Engineering Larry -W. Mays (Wiley, John & Sons)
62
32CE05T : ESTIMATING & COSTING
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: Method of estimating, measurements, taking out quantities.
UNIT-II: Typical estimates for buildings and Civil Engineering Works, Specifications for all
types building items.
UNIT-III: Analysis of rates, data for various building items.
UNIT-IV: Earthwork calculations.
UNIT-V: Introduction to Departmental procedures, tender, contracts, arbitrations, valuation
of buildings.
REFERENCE BOOKS:
B.N Dutta, Estimating and Costing in Civil Engineering Theory and Practice
M. Chakraborti, Estimating, Costing and Specifications in Civil Engineering.
63
32CE06P : STEEL STRUCTURES DETAILING
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
1. Drawing of plan and section of various types of bolted and welded joints.
2. Detailing of a Axially Loaded angle Tension Member
3. Detailing of an Axially Loaded Compression Member with base plate.
4. Detailing of an Axially Loaded Built up Laced Compression Member.
5. Detailing of an Axially Loaded Built up Battened Compression Member.
6. Detailing of a Riveted / Bolted Plate girder.
7. Detailing of a Welded Plate girder.
8. Detailing of flexible connections
9. Detailing of Semi – Rigid Connections
10. Detailing of Rigid Connections
11. Detailing of a Industrial shed
12. Detailing of a Truss Bridge Railway Bridge.
13. Preparation of Bill of Materials
14. Preparation of Fabrication drawings.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
1. Turbidity by Nephelometer.
2. TDS and fixed solids by Gravimetric method.
3. pH using pH-Meter.
4. Carbonate, Bi-Carbonate & Hydroxide Alkalinity.
5. Dissolved Oxygen [DO] using DO meter.
6. Concentration of Chlorides.
7. Optimum coagulant dose for coagulation by Jar test apparatus.
8. Chlorine Demand of Water.
9. Total Hardness and Calcium Hardness.
10. Study of Weather Monitoring Station.
11. Study of Sound Level Meter.
64
32CE08P: GEO- TECHNICAL ENGINEERING –II - LAB
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
65
SEMESTER VII
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: continuous beam and slab systems (one way and two way)
UNIT II: Combined footings (Rectangular, Trapezoidal and strap footing)
UNIT-III: Design of Cantilever retaining wall and introduction to counter fort retaining walls.
UNIT-IV: Water tanks-resting on ground
UNIT-V:Elevated water tanks (Intze Tank)
REFERENCE BOOK:
Design of Reinforced Concrete Structures by P. Dayaratnam
Reinforced Concrete Design by S.N .Sinha
Reinforced Concrete Design by Pillai & Menon
Limit State Design of Reinforced Concrete by P.C. Verghese
66
41CE02T : ENVIRONMENTAL ENGINEERING – II
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT - I :Objective,design period, Physical, Chemical and Biological characteristics. Waste
water sampling, Self-purification of natural streams, effluents Standards, Oxygen Sag Curve,
Sources of sewage. Design of sanitary sewers, Minimum size of sewer, velocities in sewers
and gradient of sewers. Sewer appurtenances viz manholes, street inlets, flushing devices,
Vent pipes etc.
UNIT – II: Waste Water primary Treatment: characteristics of wastewater. effluent discharge
standards, Primary, secondary and tertiary treatment of wastewater. Types of screens,
design of screen chamber, Sources of grit, design of grit chamber, disposal of grit, Oil and
grease removing skimming tanks, Design of PST with inlet and outlet details, Primary Sludge
and its disposal
UNIT - III :Aerobic Treatment Units : Biological principle of ASP, SVI, sludge bulking and
control; Biological principle of Trickling filter, Re-circulation, Operational troubles.; Rotating
Biological Contactor. Low Cost Treatment methods: Principle of Oxidation pond, symbiosis,
principle of Aerated Lagoons, aeration method, Principle of Oxidation Ditches, sewage
farming, ground water recharge .
UNIT- IV: Anaerobic Treatment Units : Septic tanks, biological Principle, method of
treatment and disposal of Tank effluent. Anaerobic Digester, principle of anaerobic
digestion, Stages of digestion, Bio-gas production. Sludge disposal methods, advantages and
disadvantages
UNIT – V: Municipal Solid Wastes: Characteristics, generation, collection & transportation
of solid wastes, engineered systems for solid waste management (reuse/ recycle, energy
recovery, treatment & disposal), environmental & health implications, disposal of solid
waste by land filling, composting and incineration methods. Hazardous waste management,
environmental and health implications due to Exposure, incineration, landfill disposal, site
remediation,disposal of refuse by Composting.
TEXT BOOKS:
Environmental Engineering – Peavy & Rowe (Tata McGraw Hill, New Delhi).
Waster Water Engineering – S.K. Garg (Khanna Publication).
Manual on sewerage & sewage Treatment published by Ministry of UrbanDev GOI,.Ministry
of Urban development
REFERENCE BOOKS:
Waste Water Engineering – Metcalf Eddy (Tata McGraw Hill, New Delhi).
Hazardous Waste management : M.D. LaGrega, P.L. Buckingham, J.C.Evans
Manual on Municipal Solid Waste Management : CPHEEO (Ministry of Urban Dev.)
Environmental Engineering-II.P.Venugopala Rao Tata McGraw Hill Water and Wastewater
Technology ,Hammer ( PHI)
67
41CE03T : WATER RESOURCES ENGINEERING - II
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT 1: Dams: Types of Dams, Forces, failure of dams and criteria for structural stability,
principal and shear stress, stability analysis, Elementary profile of a gravity dam, Profile from
practical considerations, Openings in dams .
UNIT 4: Regulation Works: Introduction, Definition of falls, necessity and location of falls,
comparative study of the main types of falls. Hydraulic Gates: Spillway gates, types, Tainter
gates, Roller gates.
UNIT 5: Cross Drainage Works: Introduction, suitability, various types of C-D Works, Design
principles of C-D Works
Irrigation, Water Resources and Water Power Engineering – Dr. P.N. Modi (Standard Book
House)
Theory and Design of Irrigation Structures (Volume – I & II) – Varshney (Nem Chand Bros.)
68
LIST OF ELECTIVE – I & II
69
41CE04T : DESIGN OF PRESTRESSED CONCRETE
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: Methods, Systems and Materials. Basic principles, methods and systems of
prestressing, external, internal, full, partial, pre-tensioning and post-tensioning, quality of
concrete and steel, I.S. Code provisions for allowable stresses, Advantages of prestressing
and importance of high strength materials.
UNIT-II: Analysis of Structures for Flexure. Cases of axial and eccentric prestressing allowing
suitable percentage loss of prestress. Stresses in concrete at various stages, lever arm
concept and center of pressure, pressure line, kern distances, load balancing cable profiles,
critical span (for solid slabs only), Efficiency of a section.
UNIT –III: Losses of Prestressing. Various types of losses of prestress and their calculation,
loss due to friction, I.S. Code provisions, Elastic shortening due to successive tensioning of
cables. Design of section for flexure. I.S. Code provisions for cover and spacing, standard
Fressinet and Gifford Udall cables, Design of beams and slabs, cable zones and profiles.
UNIT –IV: Composite Beams. Different types, Loading conditions, analysis for stresses,
differential shrinkage. bond and anchorage; Bond stress and its significance in pre-tensioned
beams, transmission length, determination of bursting force due to anchor zone stresses and
provision of steel according to I.S. Code for prestressed concrete. Shear: Calculation of
diagonal tension and its inclination (including vertical prestressing also) provision of steel
according to elastic method and I.S. Code method, advantages of prestressing.
UNIT-V: Limit State Design. Limit state of serviceability and strength, calculation of ultimate
bending moment for given sections, advantages of limit state method over working stress
method. Miscellaneous uses. Analysis and design of poles and circularly prestressed pipes
and tanks.
70
41CE05 T: THEORY OF PLATE & SHELLS
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-1: Simple bending of Plates-Assumptions in thin plate theory-Different relationships-
Different, Boundary Conditions for plates- Plates subjected to lateral loads – Navier’s
method for simply supported plates – Levy’s method for general plates – Example problems
with different types of loading.
UNIT-2: Circular plates subjected to Axi-symmetrical loads–concentrated load, uniformly
distributed load and varying load – Annular circular plate with end moments.
UNIT-3: Rayleigh-Ritz method – Application to different problems – Finite difference method
– Finite element methodology for plates-Orthotropic Plates
UNIT-4: Bending of anisotropic plates with emphasis on orthotropic plates – Material
Orthotropy – Structural Orthotropy - Plates on elastic foundation.
UNIT-5: Shells- Classification of shells - Membrane and bending theory for singly curved and
doubly curved shells - Various approximations - Analysis of folded plates
REFERENCES: Rudolph Szilard, Theory and Analysis of Plates, Prentice Hall, New Jercy 1986.
71
41CE07 T: REHABILITATION OF STRUCTURES
Quality assurance for concrete construction as built concrete properties strength,
permeability,thermal properties and cracking. Effects due to climate, temperature,
chemicals, wear and erosion, Design and construction errors, corrosion mechanism, Effects
of cover thickness and cracking, methods of corrosion protection Definitions: Maintenance,
repair and rehabilitation, Facets of and importance of Maintenance Preventive measures on
various aspects Inspection, Assessment procedure for evaluating a damaged structure
causes of deterioration-testing techniques. Special concretes and mortar, concrete
chemicals, special elements for accelerated strength gain, Expansive cement, polymer
concrete, sulphur infiltrated concrete, ferro cement, Fiber reinforced concrete. Rust
eliminators and polymers coating for rebars during foamed concrete, mortar repair for
cracks, shoring and underpinning.
REFERENCES
Raikar, R.N., Learning from failures – Deficiencies in Design, Construction and Service –
R&D Centre (SDCPL), Raikar Bhavan, 1987.
Allen R.T., and Edwards S.C, Repairs of Concrete Structures, Blaike and Sons, U.K.1987.
72
41CE08T : ADVANCED STRUCTURAL ANALYSIS
UNIT-I:Direct stiffness method Introduction - element stiffness matrix - rotation
transformation matrix - transformation of displacement and load vectors and stiffness matrix
- equivalent nodal forces and load vectors - assembly of stiffness matrix and load vector -
determination of nodal displacements and element forces - analysis of plane truss - plane
frame (with numerical examples) - analysis of grid - space-truss and space-frame (without
numerical examples) - computer Implementation - introduction to analysis packages (A
project on development of an analysis program using above method is envisaged at this
stage)
UNIT-II: Beams on elastic foundation: general theory - infinite beam subjected to
concentrated load - boundary conditions - infinite beam subjected to a distributed load
segment - semi-infinite beam subjected to loads at its end - semi-infinite beam with
concentrated load near its end - short beams.
UNIT-III: Beams curved in plan: Analysis of cantilever beam curved in plan - analysis of
circular beams over simple supports
UNIT-IV: Nonsymmetrical bending of straight beams: Shear centre – a review, symmetrical
and nonsymmetrical bending - bending stresses in beams subjected to nonsymmetrical
bending - deflections of straight beams subjected to unsymmetrical bending - fully plastic
load for unsymmetrical bending.
UNIT-V: Introduction to Structural Dynamics
Single degree of freedom – undamped and damped vibration-free vibration - forced
vibration, introduction to multi degree of freedom systems.
REFERENCES
Wang, C. K., Matrix Methods of Structural Analysis, International Textbook Company, 1970.
Przemeineicki, J. S., Theory of Matrix Structural Analysis, McGraw Hill, New York, 1985.
Weaver, W., and Gere, J. M., Matrix Analysis of Framed Structures, CBS Publishers, 2004.
Rajasekaran, S., and Sankarasubramanian, G., Computational Structural Mechanics, PHI
Boresi, A. P. and Sidebottom, O. M., Advanced Mechanics of Materials, John Wiley and Sons,
2003.
Srinath, L. S., Advanced Mechanics of Solids, Tata McGraw Hill, 2009.
Timoshenko, S., Strength of Materials, Part II, CBS Publishers, 2002.
Reddy, C. S., Basic Structural Analysis, Tata McGraw Hill, New Delhi, 2007.
Paz M., Structural Dynamics, CBS Publishers, 2007.
Meirovich, L., Elements of Vibration Analysis, McGraw Hill, 2007.
73
41CE09T : STRUCTURAL DYNAMICS
UNIT- 1: INTRODUCTION: Comparison between static and dynamic analysis; Degrees of
freedom; Undamped system; Newton's law of motion; ‘D’ Alembert’s principle; Solution of
the differential equation of motion.
UNIT-2: FREE VIBATION OF SINGLE DEGREE - OF - FREEDOM SYSTEM: Equation of motion
for single degree - of - freedom system; Free un damped vibration of the SDOF system;
Damped single degree - of - freedom system -Viscous damping, Equation of motion, Critically
damped system, Over damped system. Under damped system and Logarithmic decrement.
UNIT-3: RESPONSE OF SDOF SYSTEM TO HARMONIC LOADING: Undamped harmonic
excitation; Damped harmonic excitation; Evaluation of damping at resonance; Response to
support motion; Force transmitted to the foundation. RESPONSE OF' SDOF SYSTEM TO
GENERAL DYNAMIC LOADING: Impulsive loading and Duhamel's integral; Numerical
evaluation of Duhamel's integral — undamped system; Numerical evaluation of Duhamel’s
integral -Damped system.
UNIT-4: GENERALIZED COORDINATES AND RAYLEIGH'S METHOD: Principle of virtual work;
Generalized SDOF system - Rigid body; Generalized SDOF system - Distributed elasticity;
Rayleigh's method; Improved Rayleigh's method
UNIT-5: STRUCTURES MODELED AS SHEAR BUILDINGS: Stiffness equations for the shear
building; Flexibility equations for the shear building; Free vibration of a shear building (Single
bay two Storeyed) - Natural frequencies and normal modes.
FORCED MOTION OF SHEAR BUILDINGS (Two Storeyed): Modal superposition method;
Response of a shear building to base motion; Harmonic forced excitation.
REFERENCES:
Earthquake Resistant Design of Structures by Pankaj Agarwal, Manish Shrikhande , First
edition(2006), Prentice Hall of India Private Ltd., New Delhi . (for Chapters 1,2,4 and 5)
Dynamics of Structures by A.K.Chopra, Second edition (2001), Prentice Hall India Private
Ltd
74
41CE10T : EARTHQUAKE RESISTANT DESIGN OF STRUCTURES
UNIT-I: Elements of structural dynamics, Sources of vibrations; Types of vibrations; Degrees
of freedom; Spring action and damping; Free vibration of undamped system having single
degree of freedom; Free vibration of viscous damped system having single degree of
freedom; Forced vibration of a viscous damped single degree freedom system subjected to
harmonic excitation; Earthquake excitation (Base excitation) of a single degree freedom
system.
UNIT-II: Elements of Earth Quake Ground motion, Earthquake size- Intensity and magnitude;
Seismic Zoning-Introduction; Strong Motion Earthquakes - Introduction; Response spectrum
(elastic); Local site effect (Effect of type of soil).3) Elements of Geotechnical Earthquake
Engineering, Liquefaction – Definition and types, Effect of liquefaction on built environment,
Evaluation of liquefaction susceptibility, Liquefaction hazard mitigation Seismic slope
stability – Introduction, Pseudo-static analysis, Sliding block method
UNIT III: Analysis of single storey and single bay RCC Plane Frame (Columns vertical) : (As per
IS:1893(part-I)-2002). Calculation of lateral force due to earthquake using equivalent static
method ; Analysis for different load combinations; Design forces and moments in beam and
columns.
UNIT-IV: Design of single storey and single bay RCC plane frames (Columns vertical) (As per
IS:456-2000 and IS13920-1993)Design of column; Design of beam; Design of footing ;
Detailing of entire frame
Unit-V:Masonry Structures :House types and damages, cause and location of damage,
Understanding the knowledge hidden in your existing houses, Making houses earthquake
resistant, Earthquake resistant features, Retrofitting-some examples, Technology choice,
summary of earthquake resistant features, improving housing designs.
TEXT BOOKS:
Elements of Earthquake Engineering by Jai Krishna, A.R.Chandrasekaran and Brijesh
Chandra, Second Edition(1994), South Asian Publishers, New Delhi. (For Chapters 1 and 2)
Geotechnical Engineering - S.K.Gulati & Manoj Datta, Tata McGraw-Hill Publishing
Company Ltd. (For Chapter 3)
Earthquake Resistant Design of Structures by Pankaj Agarwal, Manish Shrikhande , First
edition(2006), Prentice Hall of India Private Ltd., New Delhi . (for Chapters 1,2,4 and 5)
Earthquakes and Buildings – A.S.Arya, A.Revi, Pawan Jain (For Chapter-6)
CODES: IS:1893(part-I)-2002 - IS13920-1993 - IS:456-2000 - SP16
REFERENCE BOOK
Dynamics of Structures by A.K.Chopra, Second edition (2001), Prentice Hall India Private
Ltd
75
41CE11T : FRACTURE OF CONCRETE STRUCTURES
UNIT I:Concepts of linear elastic fracture mechanics,
UNIT-II:Principles of Nonlinear fracture mechanics and energy balance approach
UNIT-III: Behaviour of materials like concrete under fracture load and fracture process of
concrete
UNIT-IV: Nonlinear fracture properties of concrete using different models, Modeling and
applications of nonlinear fracture models, R-curve behavior of concrete,
UNIT-V:Test methods for determining fracture parameters of concrete, Fracture mechanics
applications to concrete structures.
REFERENCES:
Anderson TL (2005) Fracture Mechanics Fundamentals and Applications. CRC Press, Taylor &
Fracncis Group, Boca Ranton.
Bažant ZP, Planas J (1998) Fracture and size effect in concrete and other quasibrittle
materials, Florida: CRC Press.
Karihaloo BL (1995) Fracture mechanics and structural concrete, Concrete Design and
Construction Series, Longman Scientific & Technical, Harlow, Essex, England.
Kumar S. and Barai S.V. (2011). Concrete Fracture Models and Applications. Springer.
76
Ramchandra , Design of Steel Structures Vol I and II, Standard book house , 1991
Dayaratnam, P., Design of Steel Structures, Wheeler,1998
Raghupathi, M., Design of Steel Structures, Tata McGraw Hill, 1985
Lin and Breslar, Design of Steel Structures, John Wiley and Sons, 1963
Relevant BIS codes ( IS 800, SP 6,IS 804, IS 805,IS 6533, IS 9178, IS 801,IS 811 )
77
41CE14T : ADVANCED CONCRETE TECHNOLOGY
UNIT – 1: Importance of Bogue’s compounds, Structure of a Hydrated Cement Paste, Volume
of hydrated product, porosity of paste and concrete, transition Zone, Elastic Modulus,
factors affecting strength and elasticity of concrete, Rheology of concrete in terms of
Bingham’s parameter. CHEMICAL ADMIXTURES- Mechanism of chemical admixture,
Plasticizers and super Plasticizers and their effect on concrete property in fresh and
hardened state, Marsh cone test for optimum dosage of super plasticizer, retarder,
accelerator, Air-entraining admixtures, new generation superplasticiser. MINERAL
ADMIXTURE-Fly ash, Silica fume, GCBS, and their effect on concrete property in fresh state
and hardened state.
UNIT – 2: MIX DESIGN - Factors affecting mix design, design of concrete mix by BIS method
using IS10262 and current American (ACI)/ British (BS) methods. Provisions in revised
IS10262-2004.
UNIT – 3: DURABILITY OF CONCRETE - Introduction, Permeability of concrete, chemical
attack, acid attack, efflorescence, Corrosion in concrete. Thermal conductivity, thermal
diffusivity, specific heat. Alkali Aggregate Reaction, IS456-2000 requirement for durability.
UNIT – 4: RMC concrete - manufacture, transporting, placing, precautions, Methods of
concreting- Pumping, under water concreting, shotcrete, High volume fly ash concrete
concept, properties, typical mix, Self compacting concrete concept, materials, tests,
properties, application and Typical mix.
UNIT – 5: Fiber reinforced concrete - Fibers types and properties, Behavior of FRC in
compression, tension including pre-cracking stage and post-cracking stages, behavior in
flexure and shear, Ferro cement - materials, techniques of manufacture, properties and
application. Light weight concrete-materials properties and types. Typical light weight
concrete mix High density concrete and high performance concrete-materials, properties
and applications, typical mix.
REFERENCES
Neville, A.M. and Brooks, J.J.," CONCRETE TECHNOLOGY", ELBS .1990.
Neville, A.M., "PROPERTIES OF CONCRETE", PITMAN. 1983.
Brandt, A.M., "CEMENT BASED COMPOSITES: Materials, Mechanical Properties and
Performance", E & FN Spon. 1995.
Newman, K., "CONCRETE SYSTEMS in COMPOSITE MATERIALS".EDT BY L.Holliday. Elsevier
Publishing Company. 1966.
78
41CE15T : ENGINEERING ECONOMICS
1. Basic economic concepts: Stock and Flow, Static and Dynamic economics, Micro
economics and Macroeconomics, National Income concepts.
2. Market demand : Demand, meaning and types, Law of demand, exceptions to the law of
demand, Elasticity of Demand, Methods of measuring elasticity of demand, Marginal utility
Analysis.
3. Production analysis: Production functions, law of returns, least cost combination, cost and
cost curves, choice of plant size in the long run.
4. Supply: Law of supply, elasticity of supply.
5. Cost concepts and estimation: Cost elements, economic vs. accounting concepts of costs
and Revenues, Standard Cost, Actual Cost, Over head Cost, Cost control,
Break-Even-Analysis.
6. Economic appraisal techniques: Long- Range and Short range Budgeting, Criteria for
Project Appraisal, Social benefit-cost analysis, Depreciation: concepts and Techniques.
7. Monetary System: Money and its functions, Functions of the Commercial Bank and Central
Bank, Monetary Policy.
8. Inflation and business cycles: Causes, effects and methods to Control Inflation, Concepts
of Business Cycles.
9. Accounting: Book keeping single and double entry system, Journal and ledger, Trading
account, Profit and loss account, Balance sheet.
BOOKS:
A Text Book of Economic Theory : Stonier and Hauge.
Modern Economic Theory : K.K.Dewett
Engineering Economics : Degramo.
A Text Book of Economic Theory : Sammuelson.
International Economics : Bo Sodersten
Principles of Macroeconomics : Rangarajan and Dholakia.
Monetary Economics : Suraj B. Gupta
79
41CE16T : QUALITY CONTROL & ASSURANCE IN CONSTRUCTION
UNIT 1: CONSTRUCTION PROJECTS : Agencies involved in Construction Projects, mutual
relationship, quality control at site; and whose job is it.
UNIT 2: ISO / IS Requirements : IS 9000 (Parts 1 to 4) (Pt 1; 1994, Pt 2; 1993, Pt 3; 1991, Pt 4;
1993) for Total Quality Management. ISO 14000 – 1988 for environment – Impact of large
construction projects.
UNIT 3: Quality Control on Construction Projects : Inspection of reinforced concrete,
masonry and steel works, testing techniques and quality at reports.
UNIT 4: Statistical Analysis : Sampling frequencies, statistical and reliability analysis,
optimum sample size.
UNIT 5: Quality Assurance : Quality Assurance in constructions
Name of Text Books:
ISO 9000 in Construction – Nee, Paul A. (Wiley Interscience Publication, 1994)
IS: 14000, – Quality System – Guidelines for Selection and Use of Standards on Quality
System 1988.
NAME OF REFERENCE BOOKS:
ISO 9000 in Construction – Wah, L.S., Min., L.C. & Ann, T.W. (McGraw Hill Book Company,
199 Construction Engineering and Management – S. Seetaraman (Umesh Publication)
80
41CE18T : VALUE ENGINEERING
UNIT-I: Basic Concepts: Meaning of the term value, basic kind, reasons for poor value, value
addition, origin and history. Benefits, relevance in Indian scenario.
UNIT-II:Techniques: Different techniques, organizing value engineering study, value
engineering and quality.
UNIT-III: Job Plan: Different phases, General phase, Information phase, Functional Phase,
Creation Phase, Evaluation Phase, Investigation Phase, Implementation Phase, Audit.
UNIT-IV: Selection of evaluation of VE Projects: Project selection, method selection, value
standard, application of methodology.
UNIT-V: Value Engineering Program: VE operations in maintenance and repair activities, VE
Cost, life cycle, cost model, training for VE, general value engineering, case studies.
TEXT BOOKS
Value Engineering – S.S. Iyer – New Age International Publishers, New Delhi
Industrial Engineering & Management – O.P. Khanna – Dhanpat Rai & Sons
REFERENCES
Techniques of Value Analysis and Engineering – L.D. Miles – McGraw Hill, New York
Value Engineering, A Systematic Approach – A.E. Mudge – McGraw Hill, New York
Compendium on Value Engineering – H.G. Tufty – Indo American Society
81
BOOKS:
V.K. GARG & N .K. VENKATKRISHNAN:, ERP, Concepts and Practices, PM
Rahul V. Altekar, Enterprise wide Resource Planning-theory and practice, PHI
REFERENCES:
ALEXIS LEON: Enterprise Resource Planning, TMH S. SADAGOPAN: MIS,
PMV. RAJARAMAN: Analysis and Design of Information Systems, PHIMONK' & BRADY:
Concepts in ERP, Vikas pub, Thomson
83
41CE23P: ENVIRONMENTAL ENGG.-II – LAB
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
41CE25P: SEMINAR
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
84
SEMESTER VIII
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
UNIT-I: Importance of hydrologic factors in bridge design, Hydraulic geometry, linear water
ways, economic span, afflux and scour.
UNIT-II: Brief historical review, Different types of Bridges and span range, Bridge codes,
Bridge supper structures
UNIT-III: Design of Reinforced concrete slab bridge decks and Tee beam bridge
UNIT-IV: Types of tunnel, Survey and exploration, Planning of tunnels, Stresses in tunnel.
Tunnel
UNIT-V: Tunneling methods, Various construction techniques of tunnel in soil and rock.
Text Books
Bridges and Tunnels-Jen Vaughn (Nomad Press, 2012)
Tunnel Engineering-Subhash Chandra Saxena (Dhanpat Rai & Sons)
Railways, Bridges and Tunnels- V.N. Vazirani, S. P. Chandola (Khanna Pub., 1978)
Roads,Railways,Bridges,Tunnel & Harbour Dock Engineering-B.L.Gupta & Amit Gupta,
Standard Publishers Distributors, 2007
SESSIONAL - TA
ESE
L T P IA MSE TOTAL
3 1 - 20 20 40 60
85
Importance, Elements of quality, Quality Assurance Techniques, Quality Control Circles. Total
Quality Management in construction, Introduction, Elements of TQM, Approaches to total
quality, difference between traditional management and TQM. Applications and constants
of TQM in construction process.
UNIT 4: Construction Equipments and Management : Classification of construction
equipments,
Earth moving equipments: Power shovel, hoe, dozer, dumper, trailers and tractor, rollers,
sheet foot rollers, pumps, hauling equipments, hoisting equipments, aggregate and concrete
production equipments: Weight batcher, Mixer, Vibrator, Batching Plant, Concrete pump,
Cranes, Lifting equipment, pile driving equipments.
UNIT 5
Time and motion studies, waiting line theory, factors affecting selection of construction
equipments, cost of owning and operating the construction Equipment, equipment
maintenance.
NAME OF TEXT BOOKS:
Construction Engineering and Management – S. Seetharaman (Umesh Publications, New
delhi, 1997)
PERT & CPM – Punmia, B.C. and Khandelwal, K.K. (Laxmi Publications, New Delhi 1997)
Construction Management and Planning – Sen Gupta & Guha (Tata McGraw Hill)
Name of Reference Books:
Construction Planning Equipment and Methods – Peurify/ Schexnayder, 6th Edition (Tata
McGraw Hill)
PERT & CPM – Sreenath, I.S. (East West Press, New Delhi, 1975)
Construction Management and Accounts – Vazirani,V.N. & Chandola, S.P. (Khanna
Publishers, New Delhi, 2002)
Construction Planning and Management – Gahlot & Dhir (New Age Publishers)
86
LIST OF ELECTIVES – III & IV
87
42CE03T : AIR AND WATER QUALITY MODELLING
UNIT-1: Modelling/Concept: Water and air quality management – Role of mathematical
models; systems approach –systems and models – kinds of mathematical models – model
development and validation effluent and stream standards; ambient air quality standards.
UNIT-2: Surface Water Quality Modelling: Historical development of water quality models;
rivers and streams water quality modeling – river hydrology and flow – low flow analysis –
dispersion and mixing – flow, depth and velocity – estuaries – estuarine transport, net
estuarian flow, estuary dispersion coefficient; Lakes and impoundments – Water quality
response to inputs; water quality modeling process – model sensitivity – assessing model
performance; Models for dissolved oxygen, pathogens; Streeter – Phelps models.
UNIT-3: Air Quality Modelling: Transport and dispersion of air pollutants – wind velocity,
wind speed and turbulence; estimating concentrations from point sources – the Gaussian
Equation – determination of dispersion parameters, atmospheric stability; dispersion
instrumentation – Atmospheric traces; concentration variation with averaging time; Air
pollution modeling and prediction – Plume rise modeling techniques, modeling for non-
reactive pollutants, single source – short term impact, multiple sources and area sources,
model. performance and utilisation, computer models.
UNIT-4: Groundwater Quality Modelling: Mass transport of solutes, degradation of organic
compounds, application of concepts to predict groundwater contaminant movement,
seawater intrusion – basic concepts and modeling.
UNIT-5: Computer Models: Exposure to computer models for surface water quality,
groundwater quality and air quality.
REFERENCES:
Steven C.Chapra, Surface Water Quality Modeling, The McGraw-Hill Companies,
Inc., New York, 1997.
R.W.Boubel, D.L. Fox, D.B. Turner & A.C. Stern, Fundamentals of Air Pollution
Academic Press, New York, 1994.
Ralph A. Wurbs, Water Management Models – A Guide to Software, Prentice
Hall. PTR, New Jersey, 1995.
88
42CE04T : INDUSTRIAL WASTEWATER MANAGEMENT
UNIT-1: Introduction: Industrial scenario in India– Industrial activity and Environment - Uses
of Water by industry – Sources and types of industrial wastewater – Nature and Origin of
Pollutants - Industrial wastewater and environmental impacts – Regulatory requirements for
treatment of industrial wastewater – Industrial waste survey – Industrial wastewater
monitoring and sampling -generation rates, characterization and variables –Toxicity of
industrial effluents and Bioassay tests – Major issues on water quality management
UNIT-2: Industrial Pollution Prevention: Prevention and Control of Industrial Pollution –
Benefits and Barriers – Waste management Hierarchy - Source reduction techniques –
Pollution Prevention of Assessment - Material balance - Evaluation of Pollution prevention
options –Cost benefit analysis – pay back period - Waste minimization Circles
UNIT-3: Industrial Wastewater Treatment: Equalisation - Neutralisation – Oil separation –
Flotation – Precipitation – Heavy metal Removal– Aerobic and anaerobic biological
treatment – Sequencing batch reactors –High Rate reactors - Chemical oxidation – Ozonation
– carbon adsorption -Photocatalysis – Wet Air Oxidation – Evaporation – Ion Exchange –
Membrane Technologies – Nutrient removal.- Treatability studies.
UNIT-4: Wastewater Reuse And Residual Management: Individual and Common Effluent
Treatment Plants – Joint treatment of industrial and domestic wastewater - Zero effluent
discharge systems - Quality requirements for Wastewater reuse – Industrial reuse , Present
status and issues - Disposal on water and land – Residuals of industrial wastewater
treatment – Quantification and characteristics of Sludge – Thickening, digestion,
conditioning, dewatering and disposal of sludge – Management of RO rejects.
UNIT-5: Case Studies: Industrial manufacturing process description, wastewater
characteristics, source reduction options and waste treatment flow sheet for Textiles –
Tanneries – Pulp and paper – metal finishing – Oil Refining – Pharmaceuticals – Sugar and
Distilleries.
REFERENCES:
Eckenfelder, W.W., ‘Industrial Water Pollution Control’, Mc-Graw Hill, 2000.
Nelson Leonard Nemerow, “Industrial waste treatment – contemporary practice and
vision for the future”, Elsevier, Singapore, 2007
Frank Woodard, ‘Industrial waste treatment Handbook’, Butterworth Heinemann,
New Delhi, 2001.
World Bank Group, ‘Pollution Prevention and Abatement Handbook – Towards
Cleaner Production’, World Bank and UNEP, Washington D.C., 1998
Paul L. Bishop, ‘Pollution Prevention: - Fundamentals and Practice’, Mc-Graw Hill
International, Boston, 2000.
89
42CE05T : AIR POLLUTION CONTROL ENGINEERING
UNIT-1: INTRODUCTION: Sources and classification of Air pollutants: Natural contaminants,
Aerosols, Gases & Vapors; Primary & Secondary Air pollutants; Stationary & Mobile Sources.
Meteorology and Air pollution: Factors influencing Air pollution; Atmospheric stability &
temperature inversions; Mixing height; Plume behavior; Wind rose; Stack effluent dispersion
theories; Stack height.
UNIT-2: SAMPLING PROCEDURES: Sampling Methods, Difficulties in sampling, Stages &
considerations of air sampling, Instruments for sampling waste gases & atmosphere,
sampling period & methods, High volume sampler, Stack sampling techniques, selection of
sampling location, procedure for collection & sampling of particulate matter, Gaseous
sampling, recent trends in sampling of stack effluents.
UNIT-3: Control of Particulates / aerosols: Objectives & types of Collection equipment;
Principle, application, working, advantages & disadvantages of: i) Settling chambers, ii)
Inertial separators, iii) Cyclones, iv) Filters, v) Electrostatic Precipitators & vi) Scrubbers;
Choice of equipment.
UNIT-4: Control of Smoke -Gaseous Contaminants & Odour: Smoke: Sources, measurement
by Ringelman chart, miniature chart & other method; Prevention & control of smoke.
Control of exhaust emissions. Gaseous Contaminants: Methods of control viz combustion,
absorption, adsorption, closed collection & masking. Odour Control.
UNIT-5: Control measures for Industrial Applications: Introduction to control of air pollution
by process changes. Control measures for industries such as Cement Industry, Concrete
batching plant, Asphaltic concrete plant, Glass manufacture, Asbestos processing, Thermal
Power plant and Coal tar industry.
REFERENCES:
Richard W. Boubel et al “Fundamentals of Air pollution”, Academic Press, New York, 1994.
Noel de Nevers, Air Pollution control Engineering, McGraw Hill, New York, 1995.
M.N. Rao et al, “Air Pollution” Tata McGraw Hill, 1989.
90
42CE06T : ENVIRONMENTAL IMPACT ASSESSMENT
UNIT-1: Introduction: Historical development of Environmental Impact Assessment (EIA). EIA
in Project Cycle. Legal and Regulatory aspects in India. – Types and limitations of EIA – Cross
sectoral issues and terms of reference in EIA – Public Participation in EIA. EIA process-
screening – scoping - setting – analysis – mitigation
UNIT-2: Components And Methods For Eia: Matrices – Networks – Checklists – Connections
and combinations of processes – Cost benefit analysis – Analysis of alternatives – Software
packages for EIA – Expert systems in EIA. Prediction tools for EIA – Mathematical modeling
for impact prediction – Assessment of impacts – air – water – soil – noise – biological ––
Cumulative Impact Assessment – Documentation of EIA findings – planning – organization of
information and visual display materials – Report preparation. EIA methods in other
countries.
UNIT-3: Socio-Economic Impact Assessment: Definition of social impact assessment. Social
impact assessment model and the planning process. Rationale and measurement for SIA
variables. Relationship between social impacts and change in community and institutional
arrangements. Individual and family level impacts. Communities in transition - neighborhood
and community impacts. Selecting, testing and understanding significant social impacts.
Mitigation and enhancement in social assessment. Environmental costing of projects.
UNIT-4: Environmental Management Plan: Environmental Management Plan - preparation,
implementation and review – Mitigation and Rehabilitation Plans – Policy and guidelines for
planning and monitoring programmes – Post project audit – Ethical and Quality aspects of
Environmental Impact Assessment.
UNIT-5: Sectoral EIA: EIA related to the following sectors - Infrastructure –construction and
housing Mining – Industrial - Thermal Power - River valley and Hydroelectric – coastal
projects-Nuclear Power. EIA for coastal projects.
REFERENCES:
Lawrence, D.P., Environmental Impact Assessment – Practical solutions to recurrent
problems, Wiley-Interscience, New Jersey, 2003.
World Bank –Source book on EIA
Petts, J., Handbook of Environmental Impact Assessment, Vol., I and II, Blackwell
Science, London, 1999.
Canter, L.W., Environmental Impact Assessment, McGraw Hill, New York.
91
42CE07T : SOLID AND HAZARDOUS WASTE MANAGEMENT
UNIT-1: Municipal Solid Waste Management: Legal and Organizational foundation: Definition
of solid waste – waste generation technological society – major legislation, monitoring
responsibilities, sources and types of solid waste – sampling and characterization –
Determination of composition of MSW – storage and handling of solid waste – Future
changes in waste composition.
UNIT-2: Collection and Transport of Solid Waste: Collection of Solid Waste: Type of waste
collection systems, analysis of collection system –alternative techniques for collection
system. Separation and Processing and Transformation of Solid Waste: unit operations user
for separation and processing, Materials Recovery facilities, Waste transformation through
combustion and aerobic composting, anaerobic methods for materials recovery and
treatment – Energy recovery – Incinerators
Transfer and Transport: Need fir transfer operation, transport means and methods, transfer
station types and design requirements. Landfills: Site selection, design and operation,
drainage and leachate collection systems – requirements and technical solution, designated
waste landfill remediation – Integrated waste management facilities.
UNIT-3: Hazardous Waste Management: Definition and identification of hazardous wastes-
sources and characteristics – hazardous wastes in Municipal Waste – Hazardous waster
regulations – minimization of Hazardous Waste-compatibility, handling and storage of
hazardous waste-collection and transport, ewaste - sources, collection, treatment and reuse
management.
UNIT-4: Hazardous waste treatment and Design: Hazardous waste treatment technologies -
Design and operation of facilities for physical,
chemical and thermal treatment of hazardous waste – Solidification, chemical fixation and
encapsulation, incineration. Hazardous waste landfills: Site selection, design and operation
– remediation of hazardous waste disposal sites.
UNIT-5: Laboratory Practice: Sampling and characterization of Solid Wastes; TCLP tests and
leachate studies.
REFERENCES:
George Techobanoglous et al, “Integrated Solid Waste Management”, McGraw-Hill
Publication, 1993.
Charles A. Wentz; “”Hazardous Waste Management”, McGraw Hill
Publication, 1995.
92
42CE08T : ENVIRONMENTAL GEOTECHNOLOGY
UNIT-2: Characterization, Stabilization and Disposal: Safe disposal of waste – site selection
for land fills – characterization of land fill sites – waste characterization –stability of landfills
– current practice of waste disposal- passive contaminant system - Hazardous waste control
and storage system – mechanism of stabilization - solidification of wastes – micro and macro
encapsulation – absorption, adsorption, precipitation- detoxification –– organic and
inorganic stabilization
UNIT-4: Detection and Testing Methods: Methodology- review of current soil testing
concepts – Proposed approach for characterization and identification of contaminated
ground soil for engineering purposes
REFERENCES:
Daniel, B.E., Geotechnical practice for waste disposal, Chapman and Hall, London, 1993.
Fang, H.Y. Introduction to environmental Geotechnology, CRC press New York, 1997.
Lagrega, M.d., Bukingham, P.L., and Evans, J.C., Hazardous Waste Management, McGraw
Hill, Inc. Singapore, 1994.
93
42CE09T : Water Resources Planning & Management
UNIT 1: Introduction: Role of water in national development, assessment of water resources
of country, scope of water resources development vis-a-vis environment, Irrigation
development in India, utilisation of Irrigation potential.
UNIT 2: Planning: Water resources planning process; planning for single purpose and
multipurpose projects, estimation of different water needs and project formulations,
comparison of alternatives, cost-benefit analysis.
UNIT 3: Water Resources Systems: Definition, types of system, optimization techniques,
system approach, system analysis, linear programming, formulation of a linear programming
problem, formulation with different types of constraints, graphical analysis, graphical
solution, simplex method, optimization techniques and systems approach.
UNIT 4: Management: Evaluation and monitoring of water quantity and quality, managing
water distribution networks for irrigation, flood control and power generation, inter-basin
transfer of water, conjunctive use of surface and ground water.
UNIT 5: Modelling: Water quantity and quality modelling, evaluation of impacts of water
resources projects on river regimes and environment, reservoir sedimentation and
watershed management.
NAME OF TEXT BOOKS:
Principles of Water Resources Planning – Good Man, A.S., (Prentice Hall, Inc., Englewood
Cliffs, N.J. 1984.)
Water Resources Engineering – Linsley, R.K. and Franzini, J.B., (3rd Edition) (McGraw Hill,
New York, 1979)
Name of Reference Books:
Water Resources System, Planning and Management – M.C. Chaturvedy (Tata McGraw Hill)
System Approach to Water Management – Biswas A.K. (Tata McGraw Hill)
Water Resources System, Planning and Management – Helweg O.J. (John and Wiley & Sons)
94
42CE10T : Ground Water Hydrology
Hydrologic cycle, Water balance, Occurrence of ground water: Origin, geological formations
as aquifers, type of aquifers, groundwater basins, springs. Darcy’s Law, validity of Darcy’s
Law permeability, laboratory and field measurement of permeability, groundwater Flow
lines. Steady flow to a well, steady radial flow to a well in confined aquifer and unconfined
aquifer, Unsteady radial flow into a confined aquifer, Non equilibrium Theis equation, Theis
method of solution, multiple well system; Methods of constructions of deep and shallow
wells: The percussion (or cable tool) method of drilling, Direct circulation hydraulic rotary
method, Down the hole hammer method, well logs-receptivity logging, testing of wells for
yield, Effect of irrigation, stream flow, rainfall on groundwater fluctuations, seasonal and
secular variations, fluctuation due to miscellaneous causes; Surface and Subsurface
investigations of groundwater: Geophysical exploration, Electrical resistivity method, aerial
photo interpretation, remote sensing applications to ground water exploration, test drilling,
Artificial recharge by water spreading, through pits and shaft, recharge through other
methods; Ground water pollution: Municipal sources, liquid wastes from domestic uses,
solid wastes, Industrial sources, tank and pipeline leakage, Mining activity, agricultural
sources, septic tank and cesspools, saline water intrusion in coastal aquifers, methods to
control saline water intrusion ; Groundwater management: Concepts of Basin management,
Equation of hydrologic equilibrium, groundwater basin investigations, conjunctive use of
surface and groundwater.
TEXT BOOK:
K. C. Patra, Hydrology and Water Resources Engg., Narosa Publishing house, New Delhi.
D. K. Todd, Groundwater Hydrology, John Wiley and Sons.
REFERENCES:
H. M. Raghunath, Ground Water.
S. P. Garg, Groundwater and Tube Wells, Oxford and IBH Publishing Co., New Delhi.
V. T. Chow, Hand book of Applied Hydrology, McGraw-Hill Publishing Company, New York.
95
42CE11T : ADVANCE FLUID MECHANICS
Dynamic of Fluid Flow, One-Dimensional method, The Nervier Stokes Equation, Limiting
Case, Applications. Boundary Layer Theory for low and high Viscosity, Boundary Layer
thickness, Prandtl’s Equation, Momentum Integral Equation, Pressure Distribution in
boundary layer. Dimension analysis and similarities, Buckingham theorem, types of
similarities, forces influencing hydraulic phenomenon, significance of dimensionless
numbers, distorted model, and model proto type similarity law; Laminar and Turbulent Flow
in Pipes, Reynolds experiment, mechanism of turbulent flow, Prandtls mixing length theory,
Karmans similarity hypothesis, Universal velocity distribution near solid boundary, Hydro
dynamically smooth and rough pipes. Power law for velocity distribution, Nikuradse
experiment, Ageing of Pipes; Compressible Fluid Flow, Equation of motion, continuity
equation and energy equation. Stagnation point and its properties, flow through ducts of
varying areas, flow through convergent and divergent nozzles, effects of compressibility,
shock waves, supersonic expansion and contraction; Ideal Fluid Flow, Circulation and
Vorticity, Source and sink, combining flow field by super position, combined flow field for
Engineering importance. Doublet in rectilinear flow and Doublet with Circulation. Flow past a
cylinder curved flow and with circulation and their different combinations; Unsteady flow in
bounded systems, Quasi-steady flow, unsteady flow in pipes and open channel flow. Finite
difference representation of depth dependent-discharge, Simulation of unsteady flow in
pipes, channels and ducts. Development of St. Venant equation of continuity and motion
Non uniform flow in open channel flow, equation of gradually varied flow. Classification of
water surface profiles, location of hydraulic jump.
ESSENTIAL READING:
J. F. Douglas, J. M. Gasiorek, J. A. Swaffield, Fluid Mechanics, Pearson Education. R. J. Garde,
A. G. Mirajgaoker, Engineering Fluid Mechanics, SciTech Publication, Chennai.
SUPPLEMENTARY READING:
V. L. Streeter, Fluid Mechanics, McGraw-Hill Book, New York, 1971.
J. A. Liggett and D. A. Caughey, Fluid Mechanics: An interactive text, ASCE press.
A. K. Jain, Fluid Mechanics, Khanna Publishers, Delhi.
K. C. Patra, Engineering Fluid Mechanics and Hydraulic Machines, Narosa publishing house,
New Delhi.
Fluid Mechanics and Application with CD roams, CENGEL, Prentice Hall, New Delhi.
96
42CE12T : RAINWATER HARVESTING
Over-exploitation of groundwater - Need for artitficial recharge and rainwater harvesting -
tyeps of wells - drilling technology - design, construction and development of water wells:
dugwells and borewells; direct and reverse rotary drilling; cable tool and DTH hammer
drilling; gravel packing and well development procedures.
Types of pumps - various artificial recharge structures: recharge ponds - recharge pits -
percolation ponds - basin spreading - surface and subsurface dykes - recharge wells -
recharge borewells. Rainwater harvesting in urban areas : RWH structures - design -
construction.
Estimation of probable runoff from an area including from roof tops - maintenance and
monitoring of RWH structures. Study of benefits - effects on local groundwater
environments - remedial measures. Recycling of domestic water - sources of water for
recharge in urbann areas.
Precautions for source, construction and establishing RWH structures. Exploration
techniques and selection of artificial recharge zones - electrical resistivity investigations
using horizontal profiling and vertical sounding techniques: interpretation of resistivity data
in terms of subsurface geology.
BOOKS:
Groundwater Hydrology, David Keith Todd, 2nd edition, 1976, John Wiley and Sons, New
York.
Groundwater, S.Ramakrishnan, 1998, Published by the Author, Chennai 600 041, India.
Holmes' Principles of Physical Geology, Duff, 4th Edition, 1993, Chapman and Hall India,
Chennai 600 035.
Textbook of Engineering Geology and General Geology, Parbin Singh, 6th Edn, 2003,
S.K.Kataria and Sons, Delhi 110 051, India.
Groundwater and Tube Wells, S.P.Garg, 2nd Edition, 1987, Mohan Primlani for Oxford and
IBH Publishing Co.Pvt Ltd, New Delhi 110001.
Groundwater, S.Sankara Pitchaiah, 1995, Scientific Publishers, Jodhpur 342 001, India.
Water Resource Systems - Hydrological risk, Management and Development, Edited by
Guenter Blosch, Stewart Franks, Michio Kamagai, Katumi Musiake and Dan Rosbjery.
Proceedings of an international symposium held during IUGC 2003, the XXIII General
Assembly of the International Union of Geodesy and Geophysics at Sapporo, Japan.
Water Management in Urban Areas, 2003, Proceedings of Training of Trainers, Central
Groundwater Board, Chennai, India.
Rainwater Harvesting Techniques to augment Groundwater, 2003. Ministry of Water
Resources, Central Groundwater Board, Faridabad, India.
Water Resource and Water Quality Management for Sustainable Drinking Water Supply,
proceedings published by the Tamil Nadu Water and Drainage Board, Chennai, India 2001.
97
42CE13T : ADVANCE TRANSPORTATION ENGG.
UNIT 1: Rail transport, Railway surveying, Rolling stock and track resistance, Permanent way,
Railway gauges, Sleepers, Ballast and Track design.
UNIT 2: Track maintenance, Station and yards, Points and crossings, Signaling, Tractive
power and tractive resistance.
UNIT 3: Introduction, Highway Surveys and plans, Highway alignment, Road Drainage, Road
geometrics.
UNIT 4: Traffic engineering, Road materials: Soil, Aggregate, Binders: Bitumen. Road
Pavement, Soil stabilization, Design factor, Design of flexible pavements, Design of rigid
pavements.
UNIT 5: Road Maintenance: General causes, Failure of flexible pavements, typical flexible
pavement failures, Failure in cement concrete pavements, typical failure of rigid pavements,
maintenance of bituminous roads, formation of waves and corrugations in flexible
pavements, remedial measures for waves and corrugations.
Tunnels: Advantages and disadvantages, Economics, Selection of routes, classification.
Tunnel surveying, methods of tunnelling in soft strata, compressed air methods, tunneling in
rock, safety precaution, tunnel lining, tunnel drainage, tunnel ventilation.
NAME OF TEXT BOOKS:
S. Chandra & M. M. Agarwal, Railway Engineering, Oxford University Press, New Delhi, 1st
Ed. 2007.
R. Srinivasan, Harbour Dock and Tunnel Engineering, Charotar Publishing House, 20th Ed.
2006.
Traffic Engineering and Transport Planning – Kadiyali, L.R. (Khanna Publishers, Delhi, 1996)
Transport Planning and Traffic Engineering – Flaherty, CAO (John Wiley & Sons, Inc., New
York, 1997)
Traffic Engineering – McShane, W.R. and Roes, R.P. (Prentice Hall, New Jersey, 1990)
NAME OF REFERENCE BOOKS:
Principles of Urban Transport Systems Planning – Hutchinson, B.G. (Scripta Book Company,
Washington,D.C., 1974)
Modelling Transport – Ortuzar, title D. and Willumson, L.G. (John Wiley & Sons, New York,
1995)
M. M. Agrawal, Railway Engineering, Standard Publishers New Delhi, 2002.
S. C. Saxena & S. P. Arora, A text Book of Railway Engineering, Dhanpat Rai & Sons.
S. C. Saxena, Tunnel Engineering, Dhanpat Rai & Sons, 2006.
Transport Planning and Traffic Engineering – Flaherty, CAO’(Ed.) (John Wiley & Sons, Inc.,
New York, 1997)
Traffic Flow Fundamentals – May, A.D. (Prentice Hall, Englewood Cliffs, New Jersey, 1990)
98
42CE14T:GROUND IMPROVEMENT TECHNIQUES
Introduction: Engineering properties of soft, week and compressible deposits, Natural on
land, off-shore and Man-made deposits. Role of ground improvement in foundation
engineering, methods of ground improvement, Selection of suitable ground improvement
techniques ; In-situ methods: In-situ densification soils, Dynamic compaction and
consolidation, Vibrofloation ,Sand pile compaction, Preloading with sand drains and fabric
drains, Granular columns, Micro piles, Soil nailing, Ground Anchors, Lime piles, Injections,
Thermal, Electrical and Chemical methods, Electro osmosis, Soil freezing ; Reinforced Soil:
The Mechanism, Reinforcement materials, Reinforcement - Soil Interactions, Geosynthetics,
Principles, Analysis and Design of Reinforced Retaining Structures, Embankments and Slopes,
soil nailing.
ESSENTIAL READING:
R. M. Korner, Design with Geosynthetics, Prentice Hall, New Jersey, 3rd Edn. 2002.
P. P. Raj, Ground Improvement Techniques, Tata McGraw Hill, New Delhi, 1995.
SUPPLEMENTARY READING:
B. M. Das, Principles of Foundation Engineering Thomson, Indian Edition, 2003.
G. V. Rao & G. V. S. Rao, Text Book on Engineering with Geotextiles, Tata McGraw Hill
T. S. Ingold & K. S. Miller, Geotextile Hand Book, Thomas Telfrod, London.
N. V. Nayak, Foundation Design Manual, Dhanpat Rai and Sons, Delhi.
99
42CE15T:DYNAMICS OF SOIL & FOUNDATION
Vibration of elementary systems, Analysis of systems with Single degree and multi-degree of
freedom. Natural frequencies of continuous systems; Elastic Constants of soil and their
experimental determination. Effect of vibration on soil properties; Bearing capacity of
dynamically loaded foundations. ; Principles of Machine foundation design, Experimental
and analytical determination of design parameters. ; Design of foundations for turbines,
vertical and horizontal reciprocating engines; forge hammers, Effect of machine foundation
on adjoining structures, vibration isolation.
ESSENTIAL READINGS:
S. Saran, Soil Dynamics and Machine Foundations, Galgotia Publications Private Ltd.1999.
N. S. V. K. Rao, Vibration Analysis and Foundation Dynamics, Wiley New Delhi, 1998.
SUPPLEMENTARY READINGS:
B. M. Das, Principles of Soil Dynamics, Thomsons Engineering, 1992.
K. G. Bhatia, Foundations For Industrial Machines, D-CAD Publishers, 2008.
A. Major, Vibration analysis and design of foundations for machines and turbines: Dynamical
problems in civil engineering, Akademiai Kiado Budapest Collets Holding Ltd., 1962.
100
UNIT-4: Data Quality, Errors and Natural Variation: Sources of error, Errors resulting from
natural variation of from original measurements. Errors arising through processing,
problem; and errors arising from overlay and boundary intersections. Errors resulting rrom
rasterizing a vector map. Errors associated with overlaying two or more polygon networks.
The nature of boundaries. The statistical nature of boundaries. Combining attributes from
overlaid maps. Classification methods: Classification, Multivariate analysis and classification,
allocating individuals to existing classes. Expert systems for Geographical Information
Systems. Classification methods in geographical information systems.
UNIT-5: Methods of Spatial interpolation. The available methods for interpolation, global
methods of interpolation, location interpolators, optimal interpolation methods using spatial
auto covariance. Extensions of crigging to large areas. Comparing crigging with other
interpolation techniques. Choosing a Geographic Information System. Designing the needs
for GIS. The procedure to following when setting up a geographical information system.
Tools for Map analysis: Single maps, Map reclassification, operations and attribute tables,
spatial topological and geometric modeling and operations on spatial Neighborhood. Tools
for map Analysis: Map pairs, map overlay and map modeling correlation between two maps.
Tools for map analysis: Multiple maps, types of models, Boolean logic models, Index overlay
models, Fuzzy logic methods.
LIST OF TEXT BOOKS
Principles of Geographical Information System for Land Resource Assessment, P.A. Burrough,
Clarendon Press, Oxford, 1986.
Geographic Information Systems, T.R. Smith & Piqent, London Press, 1985.
Principles of data base systems, J.D. Ullman, Computer Science Press.
42CE17T: ROCK MECHANICS
UNIT – 1: INTRODUCTION TO ROCK MECHANICS: Definition, Scope and importance,
development, application in mining, Discontinuities; Description of discontinuities,
Introduction to mapping and hemispherical projection of discontinuities, Barton’s shear
strength of joints. ANALYSIS OF STRESS: Introduction, Definition and basic concepts, stress in
a plane, (two dimensional stress), Mohr’s Circle of stress, Secondary principal stress,
equations of equilibrium, plane stress equations.
UNIT – 2: ANALYSIS OF STRAIN: Introduction, Definition and basic concepts, strain in a plane,
(two dimensional stress), Mohr’s Circle of strain, equations of compatibility, stess-strain
relationship, basic equations in elastic theory, plain strain equations, elasto plastic behaviour
of rocks. Stress – strain curves of various rocks. PHYSICAL PROPERTIES: Definition and
determination of Density, hardness, porosity, permeability, moisture content, degree of
saturation. Electrical and thermal properties of rocks.
UNIT – 3: MECHANICAL PROPERTIES: Definition and determination of Compressive Strength,
tensile strength, shear strength, triaxial testing. Time dependent properties. Scaling of
laboratory data to in-situ values. Rock Indices: protodyakanov strength index, point load
strength index, RQD. IN-SITU STRENGTH PROPERTIES OF ROCKS:Necessity and requirement,
101
methods of in-situ stress measurements. Plate load test, cable jack test, bore hole test,
dilatometer test, flatjack test, hydraulic fracture and velocity propagation.
UNIT – 4: RHEOLOGICAL MODELS: Relationship and rate of change of stress-strain for
idealizing materials – Models representing elastic, plastic, viscous, elasto plastic, non-elastic
and brittle rock properties.
UNIT – 5: STATIC AND DYNAMIC ELASTIC CONSTANTS OF ROCKS: Static: Introduction,
definition, instrument, measurement of deformation: mechanical, optical, electrical gauges,
LVDT, calculation of elastic constants of rocks. Dynamic: Introduction, elastic wave,
calculation of modulus of elasticity.
TEXT BOOKS:
Strata Mechanics in Coal Mining - Jeremic, K. L. Jeremic, Rotterdam, Balkema, 1985.
Fundamentals of Rock Mechanics - Jager & Cook, Methuen andco. London, 1969.
REFERENCE BOOKS:
Continuum Theory of rock Mechanics - Csaba Asszonyi, Transtech Publications, 1979.
Hand Book on Mechanical Properties of rocks - R.D. Lama, V. S. Vutukuri, Vol. I to IV,
Transtech Publications, 1978.
Mechanics and Engineering - Charles Jaeger, Cambridge University Press, 1979.
Rock Mechanics for Underground Mining - 2nd edition, Brady and Brown, Kluwer Academic
Publlishers, 1993.
Ground Mechanics in Hard rock Mining - M. L. Jeremic, Oxford & IBH Publishing Co. Pvt. Ltd.,
New Delhi, 1987.
Rock Mechanics and Design of Structures in Rock - L. Obert & W.I. Duvall, John wiley and
Sons, 1966.
Rock Mechanics for Engineers - B. P. Verma, 2nd edition, Khanna Publishers, 1989.
Introduction to Rock Mechanics - R. E. Goodman, 2nd edition, John wiley and Sons, 1989.
The elements of Mechanics of Mining Ground - B. S. Verma Vol. I. Julin & Co. Lucknow 1981.
Engineering Rock Mechanics, An Introduction to the Principles - John A. Hudson and John. P.
Harrison Pergamon Press 1997.
102
42CE18T: PLANING & DESIGN OF BUILDING SERVICES
TEXT BOOKS
Stein B. Reynolds J.S. & McGuinness W.J. (1986) Mechanical and Electrical Equipment for
Buildings, 7th
103
42CE19T: DISASTER MITIGATION & MANAGEMENT
Cyclones: Formation, Cyclonic precipitation, anti-cyclones, Flood: Flood and its estimation,
Flood warning, Flood protection measures. Earthquake: Causes of earthquake, plate
tectonics, seismic zoning map, Characteristics of strong ground motions & attenuation,
damage assessment, rehabilitation and retrofitting of structures. Environmental disaster:
Impact assessment studies, computation and preparedness. Disaster management:
Developing appropriate technology for disaster mitigation, Role of management teams,
importance of awareness, alertness and preparedness camp.
ESSENTIAL READING:
K. C. Patra, Hydrology and Water Resources Engineering, CRC Press, Florida, USA, 2nd
Edition.
N. Sharma, Earthquake resistant building construction, S. K. Kataria & Sons, New Delhi.
SUPPLEMENTARY READING:
P. C. Sinha, Disaster Mitigation, Preparedness, Recovery and Response, SBS Publishers &
Distributors Pvt. Ltd.
104
42CE20P: CONCRETE STRUCTURES DETAILING
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
1.Details of reinforcement in a simply supported RCC beam (singly reinforced) with the given
design data regarding the size and number of bars, stirrups their size and spacing.
2. Details of reinforcement in a simply supported RCC beam (doubly reinforced) with the
given design data regarding the size and number of bars, stirrups their size and spacing.
3. Details of reinforcement in a simply supported RCC beam (T section) with the given design
data regarding the size and number of bars, stirrups their size and spacing.
4. Details of reinforcement in a one way slab with the given design data regarding the size
and number of bars, their size and spacing.
5. Details of reinforcement in a two way slab with the given design data regarding the size
and number of bars, their size and spacing.
6. Details of reinforcement in a stair case with the given design data regarding the size and
number of bars, their size and spacing.
7. Details of reinforcement for a RCC rectangular column with isolated footing.
8. Details of reinforcement for a RCC circular column with isolated square footing.
9. Detailing of Combined footings.
10. Detailing of Retaining walls.
11. Detailing for Water Tanks.
12. Detailing for R.C.C. slab Bridge.
13. Detailing for R.C.C. T-Beam Bridge.
14. Detailing for Prestressed Concrete Girder.
15. Bar bending schedules for few of the above items.
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
SESSIONAL - TA
ESE
L T P IA MSE TOTAL TOTAL
- - 3 30 - 30 20 50
105
CODE OF CONDUCT FOR
STUDENTS
106
CODE OF CONDUCT FOR STUDENTS
The students are admitted to Guru Ghasidas Vishwavidyalaya to achieve excellence and
shape their character to become responsible citizens. They must realize their responsibility
towards the Vishwavidyalaya and to its components like faculty, staff and fellow students.
Failure to maintain a good standard of conduct shall result in disciplinary action.
Attendance: 75% attendance is compulsory in each subject.
Misconduct: Any of the following activities (but not limited to these only) will be treated as
misconduct.
1. Disruption of teaching activities or disturbing the learning process of other students on
the campus.
2. Any act on the part of the students, which disrupts functioning of the university,
endangers health and safety of campus residents and da mages Vishwavidalaya
properties.
3. Cheating in examination and supplying of false documents / information in order to seek
any consideration / favour from the University.
4. Possession or consumption of intoxicating beverages on the campus.
5. Failure to return back loaned material, settle University dues.
6. Possession of weapons.
7. Use of unparliamentarily language while in conversation with Vishwavidyalaya Staff and
fellow students.
Disciplinary Actions:
Failure to adhere to good conduct may result in disciplinary actions like:
1. A warning by the authorities.
2. Suspension from a particular class.
3. Suspension / expulsion from the University.
4. Suspension of campus privileges e.g. hostel, accommodation etc.
5. Withholding of examination result or withdrawal of awarded diploma / degree certificate.
6. Any other disciplinary action deemed appropriate by the University authorities.
107
ABOUT RAGGING
108
ABOUT RAGGING
UGC DRAFT REGULATIONS ON CURBING THE MENACE OF RAGGING IN
HIGHER EDUCATIONAL INSTITUTIONS, 2009
In exercise of the power conferred by Clause (g) of Sub-Section (1) of Section 26 of the
University Grants Commission Act, 1956, the University Grants Commission hereby makes
the following Regulations, namely-
1. Title, commencement and applicability:-
1.1. These regulations shall be called the “UGC Regulations on Curbing the Menace of
Ragging in Higher Educational Institutions, 2009”.
1.2. They shall come into force with immediate effect.
1.3. They shall apply to all the universities established or incorporated by or under a Central
Act, a Provincial Act or a State Act, to all institutions deemed to be university under
Section 3 of the UGC Act, 1956, to all other higher educational institutions, including the
departments, constituent units and hall the premises (academic, residential, sports,
canteen, etc) of such universities, deemed universities and other higher educational
institutions, whether located within the campus or outside, and to all means of
transportation of students whether public or private.
2. Objective:-
To root out ragging in all its forms from universities, colleges and other educational
institutions in the country by prohibiting it by law, preventing its occurrence by following the
provisions of these Regulations and punishing those who indulge in ragging in spite of
prohibition and prevention as provided for in these Regulations and the appropriate law in
force.
3. Defi nitions:-
For the purposes of these Regulations:-
3.1 “college” means any institution, whether known as such or by any other name, which
provides for a programme of study beyond 12 years of schooling for obtaining any
qualifi cation from a university and which, in accordance with the rules and regulations
of such university, is recognized as competent to provide for such programmes of study
and present students undergoing such programmes of study for the examination for the
award of such qualifi cation.
3.2 “Head of the institution” means the ‘Vice-Chancellor’ in case of a university/deemed to
be university, ‘Principal’ in case of a college, ‘Director’ in case of an institute.
3.3 “institution” means a higher educational institution (HEI), like a university, a college, an
institute, etc. imparting higher education beyond 12 years of schooling leading to a
degree (graduate, postgraduate and/or higher level).
3.4 Ragging” means the following: Any disorderly conduct whether by words spoken or
written or by an act which has the effect of teasing, treating or handling with rudeness
any other student, indulging in rowdy or undisciplined activities which causes or is likely
to cause annoyance, hardship or psychological harm or to raise fear or apprehension
thereof in a fresher or a junior student or asking the students to do any act or perform
something which such student will not in the ordinary course and which has the effect
109
of causing or generating a sense of shame or embarrassment so as to adversely affect
the physique or psyche of a fresher or a junior student.
3.5 “University” means a university established or incorporated by or under a Central Act, a
Provincial Act or a State Act, an institution deemed to be university under Section 3 of
the UGC Act, 1956, or an institution specially empowered by an Act of Parliament to
confer or grant degrees
4 Punishable ingredients of Ragging:-
• Abetment to ragging;
• Criminal conspiracy to rag;
• Unlawful assembly and rioting while ragging;
• Public nuisance created during ragging;
• Violation of decency and morals through ragging;
• Injury to body, causing hurt or grievous hurt;
• Wrongful restraint;
• Wrongful confinement;
• Use of criminal force;
• Assault as well as sexual offences or even unnatural offences;
• Extortion;
• Criminal trespass;
• Offences against property;
• Criminal intimidation;
• Attempts to commit any or all of the above mentioned offences against the victim(s);
• All other offences following from the defi nition of “Ragging”.
5 Measures for prohibition of ragging at the institution level:-
5.1 The institution shall strictly observe the provisions of the Act of the Central Government
and the State Governments, if any, or if enacted, considering ragging as a cognizable
offence under the law on a par with rape and other atrocities against women and ill-
treatment of persons belonging to the SC/ST, and prohibiting ragging in all its forms in all
institutions.
5.2 Ragging in all its forms shall be totally banned in the entire institution, including its
departments, constituent units, all its premises (academic, residential, sports, canteen,
etc) whether located within the campus or outside and in all means of transportation of
students whether public or private.
5.3 The institution shall take strict action against those found guilty of ragging and/or of
abetting ragging.
6 Measures for prevention of ragging at the institution level:-
6.1 Before admissions:-
6.1.1 The advertisement for admissions shall clearly mention that ragging is totally banned
in the institution, and anyone found guilty of ragging and/or abetting ragging is liable
to be punished Appropriately (for punishments, ref. section 8 below).
110
6.1.2 The brochure of admission/instruction booklet for candidates shall print in block
letters these Regulations in full (including Annexures).
6.1.3 The ‘Prospectus’ and other admission related documents shall incorporate all
directions of the Supreme Court and / or the Central or State Governments as
applicable, so that the candidates and their parents/ guardians are sensitized in
respect of the prohibition and consequences of ragging. If the institution is an affi
liating university, it shall make it mandatory for the institutions under it to
compulsorily incorporate such information in their ‘Prospectus’.
6.1.4 The application form for admission/ enrolment shall have a printed undertaking,
preferably both in English/Hindi and in one of the regional languages known to the
institution and the applicant (English version given in Annexure I, Part I), to be filled
up and signed by the candidate to the effect that he/she is aware of the law
regarding prohibition of ragging as well as the punishments, and that he/she, if found
guilty of the offence of ragging and/or abetting ragging, is liable to be punished
appropriately.
6.1.5 The application form shall also contain printed undertaking, preferably both in
English/Hindi and in one of the regional languages known to the institution and the
parent/ guardian (English version given in Annexure I, Part II), to be signed by the
parent/ guardian of the applicant to the effect that he/ she is also aware of the law in
this regard and agrees to abide by the punishment meted out to his/her ward in case
the latter is found guilty of ragging and/or abetting ragging.
6.1.6 The application for admission shall be accompanied by a document in respect of the
School Leaving Certifi cate/ Character Certifi cate which shall include a report on the
behavioral pattern of the applicant, so that the institution can thereafter keep
intense watch upon a student who has a negative entry in this regard.
6.1.7 A student seeking admission to the hostel shall have to submit another undertaking
in the form of Annexure I (both Parts) along with his/ her application for hostel
accommodation.
6.1.8. At the commencement of the academic session the Head of the Institution shall
convene and address a meeting of various functionaries/agencies, like Wardens,
representatives of students, parents/ guardians, faculty, district administration
including police, to discuss the measures to be taken to prevent ragging in the
Institution and steps to be taken to identify the offenders and punish them suitably.
6.1.9. To make the community at large and the students in particular aware of the
dehumanizing effect of ragging, and the approach of the institution towards those
indulging in ragging, big posters (preferably multicolored with different colours for
the provisions of law, punishments, etc.) shall be prominently displayed on all Notice
Boards of all departments, hostels and other buildings as well as at vulnerable places.
Some of such posters shall be of permanent nature in certain vulnerable places.
6.1.10 The institution shall request the media to give adequate publicity to the law
prohibiting ragging and the negative aspects of ragging and the institution’s resolve
to ban ragging and punish those found guilty without fear or favour.
6.1.11 The institution shall identify, properly illuminate and man all vulnerable locations.
6.1.12 The institution shall tighten security in its premises, especially at the vulnerable
places. If necessary, intense policing shall be resorted to at such points at odd hours
during the early monthsof the academic session.
111
6.1.13 The institution shall utilize the vacation period before the start of the new academic
year to launch wide publicity campaign against ragging through posters, leafl ets.
seminars, street plays, etc.
6.1.14 The faculties/ departments/ units of the institution shall have induction
arrangements (including those which anticipate, identify and plan to meet any special
needs of any specifi c section of students) in place well in advance of the beginning of
the academic year with a clear sense of the main aims and objectives of the induction
process.
6.2 On admission:-
6.2.1 Every fresher admitted to the institution shall be given a printed leafl et detailing
when and to whom he/she has to turn to for help and guidance for various purposes
(including Wardens, Head of the institution, members of the anti-ragging committees,
relevant district and police authorities), addresses and telephone numbers of such
persons/ authorities, etc., so that the fresher need not look up to the seniors for help in
such matters and get indebted to them and start doing things, right or wrong, at their
be hest. Such a step will reduce the freshers’ dependence on their seniors .
6.2.2 The institution through the leaflet mentioned above shall explain to the new entrants
the arrangements for their induction and orientation which promote effi cient and
effective means of integrating them fully as students.
6.2.3 The leafl et mentioned above shall also tell the freshers about their rights as bona fi de
students of the institution and clearly instructing them that they should desist from
doing anything against their will even if ordered by the seniors, and that they have
nothing to fear as the institution cares for them and shall not tolerate any atrocities
against them.
6.2.4 The leafl et mentioned above shall contain a calendar of events and activities laid down
by the institution to facilitate and complement familiarization of juniors with the
academic environment of the institution.
6.2.5 The institution shall also organize joint sensitization programmes of ‘freshers’ and
seniors.
6.2.6 Freshers shall be encouraged to report incidents of ragging, either as victims, or
even as witnesses.
6.3 At the end of the academic year:-
6.3.1 At the end of every academic year the Vice-Chancellor/ Dean of Students Welfare/
Director/ Principal shall send a letter to the parents/ guardians who are completing the
first year informing them about the law regarding ragging and the punishments, and
appealing to them to impress upon their wards to desist from indulging in ragging when
they come back at the beginning of the next academic session.
6.3.2 At the end of every academic year the institution shall form a ‘Mentoring Cell’
consisting of Mentors for the succeeding academic year. There shall be as many levels
or tiers of Mentors as the number of batches in the institution, at the rate of 1 Mentor
for 10 freshers and 1 Mentor of a higher level for 10 Mentors of the lower level.
6.4 Setting up of Committees and their functions:-
6.4.1The Anti-Ragging Committee:- The Anti-Ragging Committee shall be headed by the
Head of the institution and shall consist of representatives of faculty members, parents,
students belonging to the freshers’ category as well as seniors and non-teaching staff. It
112
shall consider the recommendations of the Anti-Ragging Squad and take appropriate
decisions, including spelling out suitable punishments to those found guilty.
6.4.2 The Anti-Ragging Squad:- The Anti-Ragging Squad shall be nominated by the Head of
the institution with such representation as considered necessary and shall consist of
members belonging to the various sections of the campus community. The Squad will
have vigil, oversight and patrolling functions. It shall be kept mobile, alert and active at
all times and shall be empowered to inspect places of potential ragging and make
surprise raids on hostels and other hot spots. The Squad shall investigate incidentsof
ragging and make recommendations to the Anti-Ragging Committee and shall work
under the overall guidance of the said Committee.
6.4.3 Monitoring Cell on Ragging:- If the institution is an affi liating university, it shall have
aMonitoring Cell on Ragging to coordinate with the institutions affi liated to it by calling
for reports from the Heads of such institutions regarding the activities of the Anti-
Ragging Committees, Squads, and Mentoring Cells, regarding compliance with the
instructions on conducting orientation programmes, counseling sessions, etc., and
regarding the incidents of ragging, the problems faced by wardens and other offi cials,
etc. This Cell shall also review the efforts made by such institutions topublicize anti-
ragging measures, cross-verify the receipt of undertakings from candidates/students
and their parents/guardians every year, and shall be the prime mover for initiating
action by the university authorities to suitably amendthe Statutes or Ordinances or Bye-
laws to facilitate the implementation of anti ragging measures at the level ofthe
institution.
6.5 Other measures:-
6.5.1 The Annexure mentioned in 6.1.4, 6.1.5 and 6.1.7 shall be furnished at the beginning
of each academic year by every student, that is, by freshers as well as seniors.
6.5.2 The institution shall arrange for regular and periodic psychological counseling and
orientation for students ( for freshers separately, as well as jointly with seniors) by
professional counselors during the first three months of the new academic year. This
shall be done at the institution and department/ course levels. Parents and teachers
shall also be involved in such sessions.
6.5.3 Apart from placing posters mentioned in 6.1.9 above at strategic places, the
institution shall undertake measures for extensive publicity against ragging by means
of audio-visual aids, by holding counseling sessions, workshops,painting and design
competitions among students and other methods as it deems fit.
6.5.4 If the institution has B.Ed. and other Teacher training programmes, these courses
shall be mandated to provide for anti-ragging and the relevant human rights
appreciation inputs, as well as topics on sensitization against corporal punishments
and checking of bullying amongst students, so that every teacher is equipped to
handle at least the rudiments of the counseling approach.
6.5.5 Wardens shall be appointed as per the eligibility criteria laid down for the post refl
ecting both the command and control aspects of maintaining discipline, as well as the
softer skills of counseling and communicating with the youth outside the class-room
situations. Wardens shall be accessible at all hours and shall be provided with mobile
phones. The institution shall review and suitably enhance the powers and perquisites
of Wardens and authorities involved in curbing the menace of ragging.
113
6.5.6 The security personnel posted in hostels shall be under the direct control of the
Wardens and assessed by them.
6.5.7 Private commercially managed lodges and hostels shall be registered with the local
police authorities, and this shall be done necessarily on the recommendation of the
Head of the institution. Local police, local administration and the institutional
authorities shall ensure vigil on incidents that may come within the definition of
ragging and shall be responsible for action in the event of ragging in such premises,
just as they would be for incidents within the campus. Managements of such private
hostels shall be responsible for not reporting cases of ragging in their premises.
6.5.8 The Head of the institution shall take immediate action on receipt of the
recommendations of the Anti-Ragging Squad. He/ She shall also take action suo
motto if the circumstances so warrant.
6.5.9 Freshers who do not report the incidents of ragging either as victims or as witnesses
shall also be punished suitably.
6.5.10 Anonymous random surveys shall be conducted across the 1st year batch of students
(freshers) every fortnight during the first three months of the academic year to verify
and cross-check whether the campus is indeed free of ragging or not. The institution
may design its own methodology of conducting such surveys.
6.5.11 The burden of proof shall lie on the perpetrator of ragging and not on the victim.
6.5.12 The institution shall fi le an FIR with the police / local authorities whenever a case of
ragging is reported, but continue with its own enquiry and other measures without
waiting for action on the part of the police/ local civil authorities. Remedial action
shall be initiated and completed within the one week of the incident itself.
6.5.13 The Migration / Transfer Certificate issued to the student by the institution shall have
an entry, apart from those relating to general conduct and behaviour, whether the
student has been punished for the offence of committing or abetting ragging, or not,
as also whether the student has displayed persistent violent or aggressive behaviour
or any desire to harm others.
6.5.14 Preventing or acting against ragging shall be the collective responsibility of all levels
and sections of authorities or functionaries in the institution, including faculty, and
not merely that of the specifi c body/ committee constituted for prevention of
ragging.
6.5.15 The Heads of institutions other than universities shall submit weekly reports to the
Vice-chancellor of the university the institution is affiliated to or recognized by,
during the first three months of new academic year and thereafter each month on
the status of compliance with anti-ragging measures. The Vice Chancellor of each
university shall submit fortnightly reports of the university, including those of the
Monitoring Cell on Ragging in case of an affiliating university, to the Chancellor.
6.5.16 Access to mobile phones and public phones shall be unrestricted in hostels and
campuses, except in class-rooms, seminar halls, library etc. where jammers shall be
installed to restrict the use of mobile phones.
6.6 Measures for encouraging healthy interaction between freshers and seniors:-
6.6.1 The institution shall set up appropriate committees including the course-in-charge,
student advisor, Warden and some senior students to actively monitor, promote and
regulate healthy interaction between the freshers and senior students.
114
6.6.2 Freshers’ welcome parties shall be organized in each department by the senior
students and the faculty together soon after admissions, preferably within the fi rst
two weeks of the beginning of the academic session, for proper introduction to one
another and where the talents of the freshers are brought out properly in the
presence of the faculty, thus helping them to shed their inferiority complex, if any,
and remove their inhibitions.
6.6.3 The institution shall enhance the student-faculty interaction by involving the students
in all matters of the institution, except those relating to the actual processes of
evaluation and of faculty appointments, so that the students shall feel that they are
responsible partners in managing the affairs of the institution and consequently the
credit due to the institution for good work/ performance is due to them as well.
6.7 Measures at the UGC/ Statutory/ Regulatory bodies’ level:-
6.7.1 The UGC and other Statutory /Regulatory bodies shall make it mandatory for the
institutions to compulsorily incorporate in their ‘Prospectus’ the directions of the
Supreme Court and/or the Central or State Governments with regard to prohibition
and consequences of ragging, and that noncompliance with the directives against
ragging in any manner whatsoever shall be considered as lowering of academic
standards by the erring institution making it liable for appropriate action.
6.7.2 The UGC (including NAAC and UGC Expert Committees visiting institutions for various
purposes) and similar Committees of other Statutory/Regulatory bodies shall cross-
verify that the institutions strictly comply with the requirement of getting the
undertakings from the students and their parents/ guardians as envisaged under
these Regulations.
6.7.3 The UGC and other funding bodies shall make it one of the conditions in the
Utilization Certificate for sanctioning any financial assistance or aid to the institution
under any of the general or special schemes that the institution has strictly complied
with the anti-ragging measures and has a blemishless record in terms of there being
no incidents of ragging during the period pertaining to the Utilization Certificate.
6.7.4 The NAAC and other accrediting bodies shall factor in any incident ofragging in the
institution while assessing the institution in different grades.
6.7.5 The UGC shall constitute a Board for Coordination consisting of representatives of
the AICTE, the IITs, the NITs, the IIMs, the MCI, the DCI, the NCI, the ICAR and such
other bodies which have to deal with higher education to coordinate and monitor the
anti-ragging movement across the country and to make certain policy decisions. The
said Board shall meet once in a year in the normal course.
6.7.6 The UGC shall have an Anti-Ragging Cell within the Commission as an institutional
mechanism to provide secretarial support for collection of information and
monitoring, and to coordinate with the State level and university level Committees
for effective implementation of anti-ragging measures.
6.7.7 If an institution fails to curb ragging, the UGC/ the Statutory/ Regulatory body
concerned may stop financial assistance to such an institution or take such action
within its powers as it may deem fi t and impose such other penalties as provided till
such time as the institution achieves the objective of curbing ragging.
7 Incentives for curbing ragging:-
115
7.1 The UGC shall consider providing special/ additional annual financial grants-inaid to
those eligible institutions which report a blemish-less record in terms of there being no
incidents of ragging.
7.2 The UGC shall also consider instituting another category of fi nancial awards or
incentives for those eligible institutions which take stringent action against those
responsible for incidents of ragging.
7.3 The UGC shall lay down the necessary incentive for the post of Warden in order to
attract the right type of eligible candidates, and motivate the incumbent.
8 Punishments:-
8.1At the institution level:
Depending upon the nature and gravity of the offence as established by the Anti-Ragging
Committee of the institution, the possible punishments for those found guilty of ragging at
the institution level shall be any one or any combination of the following:
8.1.1 Cancellation of admission
8.1.2 Suspension from attending classes
8.1.3 Withholding/ withdrawing scholarship/ fellowship and other benefi ts
8.1.4 Debarring from appearing in any test/ examination or other evaluation process
8.1.5 Withholding results
8.1.6 Debarring from representing the institution in any regional, national or international
meet, tournament, youth festival, etc.
8.1.7 Suspension/ expulsion from the hostel
8.1.8 Rustication from the institution for period ranging from 1 to 4 semesters
8.1.9 Expulsion from the institution and consequent debarring from admission to any other
institution
8.1.10 Fine of Rupees 25,000/-
8.1.11 Collective punishment: When the persons committing or abetting the crime of
ragging are not identifi ed, the institution shall resort to collective punishment as a
deterrent to ensure community pressure on the potential raggers.
8.2 At the university level in respect of institutions under it:
If an institution under a university (being constituent of, affi liated to or recognized by it) fails
to comply with any of the provisions of these Regulations and fails to curb ragging
effectively, the university may impose any or all of the following penalties on it:
8.2.1 Withdrawal of affi liation/ recognition or other privileges conferred on it
8.2.2 Prohibiting such institution from presenting any students then undergoing any
programme of study therein for the award of any degree/diploma of the university
8.2.3 Withholding any grants allocated to it by the university
8.2.4 Any other appropriate penalty within the powers of the university.
8.3 At the UGC level:
If an institution fails to curb ragging, the UGC may impose any or all of the following
penalties on it:
8.3.1 Delisting the institution from section 2(f) and /or section 12B of the UGC Act
116
8.3.2 Withholding any grants allocated to it
8.3.3 Declaring institutions which are not covered under section 2(f) and or 12B as
ineligible for any assistance like that for Major/ Minor Research Project, etc.
8.3.4 Declaring the institution ineligible for consideration under any of the special
assistance programmes like CPE (College with potential for Excellence), UPE
(University with Potential for Excellence) CPEPA (Centre with Potential for Excellence
in a Particular Area), etc.
8.3.5 Declaring that the institution does not have the minimum academic standards and
warning the potential candidates for admission accordingly through public notice and
posting on the UGC Website.
117
DISCIPLINE AMONG STUDENTS
IN
UNIVERSITY EXAMINATIONS
118
DISCIPLINE AMONG STUDENTS IN UNIVERSITY EXAMINATIONS
1. The end –semester examination shall be held under the general supervision of the Head of
Department by the faculty member concerned. He/she shall be responsible for the fair
and orderly conduct of the examination
2. In case of detection of unfair means (as specified in clause 1 of General Guidelines below),
the same shall be brought to the notice of the head of the department concerned for
further action specified under clause 5 of the General Guidelines below
II ENTRANCE EXAMINATIONS
1. During an entrance examination the candidates shall be under the disciplinary control of
the chief Superintendent of the centre who shall issue the necessary instructions. If a
candidate disobeys instructions or misbehaves with any member of the supervisory staff
or with any of the invigilators at the centre, he/she may be expelled from the examination
for that session.
2. The Chief Superintendent shall immediately report the facts of such a case with full details
of evidence to the Controller of Examinations who will refer the matter to the
Examination Discipline Committee in terms of clause 4 of General Guidelines below. The
committee will make recommendations for disciplinary action as it may deem fit to the
Vice-Chancellor as provided under clause 7
3. Everybody, before an examination begins, the invigilators shall call upon all the candidates
to search their persons, tables, desks, etc. and ask them to hand over all papers, books,
notes or other reference material which they are not allowed to have in their possession
or accessible to them in the examination hall. Where a late-comer is admitted this
warning shall be repeated to him at the time of entrance to the examination hall. They are
also to see that each candidate has his/her identification card and hall ticket with him/her.
119
f. Found consulting neighbours
g. Exchange of answer sheets or relevant materilas.
h. Writing some other candidate’s register number in the main answer paper.
i. Insertion of pre-written answer sheets (Main sheets or Additional sheets)
j. Threatening the invigilator or insubordinate behavior as reported by the Chief
Superintendent and / or Hall Superintendent.
k. Consulting the invigilator for answering the questions in the examination.
l. Cases of impersonation
m. Mass copying
n. Using electronic devices for the purpose of malpractice.
The Executive Council may declare any other act of omission or commission to be unfair
means in respect of any or all the examination.
2. If the Vice-Chancellor is satisfied that there has been mass-scale copying or use or unfair
means on a mass-scale at particular center(s), he may cancel the examination of all the
candidates concerned and order re-examination.
3. Where the invigilator incharge is satisfied that one third (1/3) or more students were
involved in using unfair-means or copying in a particular Examination Hall. It shall be
deemed to be a case of mass copying.
a) The Chief Superintendent of the examination centre shall report to the Controller
of Examinations without delay and on the day of the occurrence if possible, each case
where use of unfair means in the examination is suspected or discovered with full details
of the evidence in support thereof and the statement of the candidate concerned, if any,
on the forms supplied by the Controller of Examination for the purpose.
b) A candidate shall not be forced to give a statement but the fact of his /her having
refused to make a statement shall be recorded by the Chief Superintendent and shall be
got attested by two other members of the supervisory staff on duty at the time of
occurrence of the incident.
c) A candidate detected or suspected of using unfair means in the examination may
be permitted to answer the question paper, but on separate answer-book. The answer-
book in which the use of unfair means is suspected shall be seized by the Chief
Superintendent, who shall send both the answer-books to the Controller of Exami9nation
with his report. This will not affect the concerned candidate appearing in the rest of the
examinations.
d) All cases of use of unfair means shall be reported immediately to the Controller of
the Examination by the Centre Superintendent, examiner, paper-setter, evaluator,
moderator, tabulator or the person connected with the University examination as the case
may be, with all the relevant material.
4. Examination Discipline Committee
a) All the cases of alleged use of unfair means shall be referred to a committee called the
Examination Discipline Committee to be appointed by the Vice-Chancellor.
120
b) The Committee shall consists of five members drawn from amongst the teachers and
officers of the university. One member will be nominated as Chairman from
amongstthem by the Vice Chancellor.
c) A member shall be appointed for a term of two years, and shall be eligible for re-
appointment.
d) Three members present shall constitute the quorum.
e) Ordinarily, all decisions shall be taken by the Committee by simple majority. If the
members cannot reach a consensus, the case shall be referred to the Vice-Chancellor,
whose decision shall be final.
f) All decisions taken by the examination discipline committee will be placed before the
Vice-Chancellor for approval
g) A candidate within one month of the receipt of the decision of the university may
appeal to the Vice-Chancellor, in writing for a review of the case. If the Vice-Chancellor
is satisfied that the representation merits consideration, he/she may refer the case back
to the Examination Discipline Committee for reconsideration.
5 The Examination Discipline Committee may recommend one of the following punishments
for cases of unfair means
121
unfair means specified in sub- registered by the candidate for that session
clause (k) of clause
If the candidate has used Cancel the University Examination of all subjects
unfair means specified in sub- registered by the candidate for that session and debar
clause (l) of clause him/her for two years from registering and appearing for
the examination sessions. Moreover, relevant legal
action shall be initiated if an outsider is involved.
If the candidate used unfair ix) a) In the single Hall: Cancel the relevant examination
means in sub-clause (m) of taken by the students of that Hall. Debar the concerned
clause 3 Hall superintendent and other involved directly or
indirectly from the examination work such as invigilation,
question paper-setting, valuation, etc. for the next six
examination sessions.
b) In a Centre: Cancel the relevant examination taken by
the students of the center. Debare the Hall
Superintendents and the Chief Superintendent and other
involved directly or indirectly from the examination work
such as invigilation, question paper-setting, valuation,
etc. for the next six examination sessions and cancel the
examination center for two years
122
Important Contact Details
123
25. Warden-1, Girl’s Hostel Dr. Seema Rai 09406211523
26. Warden-2, Girl’s Hostel Dr. Renu Bhatt 07389451727
27 Warden-3, Girl’s Hostel Dr. Arti Srivastava 07489965977
08234003308
28 Matron- 1, Girl’s Hostel Ms. Geeta Sahu Girls Hostel office
07752-260462
29 Matron- 2, Girl’s Hostel Mrs. Janaki Sahu 09009146267
Warden -1 (Resident warden 090981-46109,
30 Mr. T.R. Ratre
S.V.B.H) Boy's Hostel 07752-260466
094252-30525,
31 Warden - 2 Boy's Hostel (S.V.B.H) Mr. Abhishek Awasthi
07752-260466
32 Warden - 2 Boy's Hostel (S.V.B.H) Mr. Saurabh Meshram 07828245128
096912-85190,
Warden - 3 Boy's Hostel (B.H. Mr. Agnivesh Pandey
33 07752-213203
Type-II IV)
07752-213204
094241-33622,
Warden - 4 Boy's Hostel (B.H. Mr. Shrawan Patel
34 07752-213203
Type-II IV)
07752-213204
Warden, Forestry Boys; Hostel Dr. Bhaskar Chaurasia 09425893212
35
125
WELL EQUIPPED LABS
CIVIL ENGINEERING DEPARTMENT
GURU GHASIDAS VISHWAVIDYALAYA, BILASPUR
126
127
D
E
P
A
R
T
M
E
N
T
O
F
C
I
V
I
L
E
N
G
I
N
E
E
R
I
N
G
128