Grizzly G0758 Mill Drill Manual PDF
Grizzly G0758 Mill Drill Manual PDF
MILL/DRILL
OWNER'S MANUAL
(For models manufactured since 02/14)
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION................................................ 2 SECTION 5: ACCESSORIES.......................... 27
Machine Description....................................... 2
SECTION 6: MAINTENANCE.......................... 28
Contact Info.................................................... 2
Schedule....................................................... 28
Manual Accuracy............................................ 2
Cleaning and Protecting............................... 28
Identification.................................................... 3
Lubrication.................................................... 28
Controls & Components.................................. 4
Table and Column Ways............................................29
SECTION 1: SAFETY........................................ 7 Z-Axis Leadscrews.....................................................29
Safety Instructions for Machinery................... 7 Table Leadscrews......................................................30
Additional Safety for Mills/Drills...................... 9 Headstock Gears.......................................................30
Quill Outside Surface.................................................31
SECTION 2: POWER SUPPLY....................... 10
Quill Rack . ................................................................31
Availability..................................................................10
Replacing DRO Battery................................ 31
Full-Load Current Rating............................................10
110V Circuit Requirements........................................10 SECTION 7: SERVICE.................................... 32
Grounding & Plug Requirements...............................11 Troubleshooting............................................ 32
Extension Cords.........................................................11 Adjusting Gibs............................................... 34
Adjusting Leadscrew Backlash..................... 34
SECTION 3: SETUP........................................ 12
Brush Replacement...................................... 35
Needed for Setup.......................................... 12
Unpacking..................................................... 12 SECTION 8: WIRING....................................... 36
Inventory....................................................... 13 Wiring Safety Instructions............................. 36
Cleanup......................................................... 14 G0758 Wiring Overview................................ 37
Site Considerations....................................... 15 G0758 Wiring................................................ 38
Lifting & Placing............................................ 16
SECTION 9: PARTS........................................ 40
Bench Mounting............................................ 17
Column.......................................................... 40
Assembly...................................................... 17
Electrical Box................................................ 42
Joining Drill Chuck & Arbor........................... 18
Headstock..................................................... 43
Lubricating Mill/Drill....................................... 18
Chip Guard................................................... 45
Test Run....................................................... 19
Labels & Cosmetics...................................... 46
Spindle Break-In........................................... 20
Inspections & Adjustments........................... 20 WARRANTY & RETURNS.............................. 49
SECTION 4: OPERATIONS............................ 21
Operation Overview...................................... 21
Downfeed Controls....................................... 22
Identification...............................................................22
Using DRO.................................................................22
Using Coarse Downfeed............................................22
Using Fine Downfeed.................................................22
Headstock Movement................................... 23
Raising/Lowering Headstock......................................23
Tilting Headstock........................................................23
Table Travel.................................................. 24
Graduated Dials.........................................................24
X-Axis Handwheel......................................................24
Y-Axis Handwheel......................................................24
Installing/Removing Tooling.......................... 25
Installing Tooling........................................................25
Removing Tooling......................................................26
Spindle Speed.............................................. 26
Determining Spindle Speed.......................................26
INTRODUCTION
Machine Description Manual Accuracy
The Model G0758 is a high-precision mill/drill with We are proud to provide a high-quality owner’s
a 600 Watt (3 ⁄4 HP) high-torque, low noise motor, manual with your new machine!
with low speed gearing for maximum torque in the
lowest RPM range. We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
This mill/drill has a spindle-to-table distance of 9" contained inside. Sometimes we make mistakes,
with a 131⁄4" swing. It has an R-8 spindle size and but our policy of continuous improvement also
features manual downfeed controls with a variable means that sometimes the machine you receive
spindle speed range from 50–2000 RPM. DRO's will be slightly different than what is shown in
for both the spindle speed and spindle downfeed the manual.
stroke allow precise operation. The headstock tilts
45° left/right and moves in the Z-axis along dove- If you find this to be the case, and the difference
tailed ways for maximum precision. between the manual and machine leaves you
confused about a procedure, check our website
The large 51⁄ 2" x 1911⁄ 16" table features manual 13" for an updated version. We post current manuals
(X-axis) and 51⁄ 2" (Y-axis) travel. All table move- and manual updates for free on our website at
ment is along precision-ground dovetailed ways. www.grizzly.com.
An optional stand (Model T26612) is available for
purchase at www.grizzly.com. Alternatively, you can call our Technical Support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
Contact Info into the machine ID label (see below). This infor-
mation helps us determine if updated documenta-
tion is available for your machine.
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Manufacture Date
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663 Serial Number
Email: [email protected]
Drawbar Cap
Spindle Speed
Digital Readout Unit Spindle Position
(DRO) Digital Readout Unit
(DRO)
Variable-Speed
Knob Fine
Downfeed
Handwheel
ON/OFF
Buttons
X-Axis
Chip Lock
Guard Levers
X-Axis
Table Stop
Handwheel
Y-Axis
Handwheel Y-Axis Lock
Levers
Z-Axis
Handwheel
Motor
High/Low
Gearbox Knob
Coarse
Downfeed
Handles
Downfeed
Selector
Knob
Work
Table
Quill Lock Lever
I
To reduce your risk of
serious injury, read this
entire manual BEFORE J L
using machine.
H K
Figure 3. G0758 controls (right side). L. Spindle Downfeed Digital Readout Unit
(DRO): Displays a precise reading of verti-
A. High/Low Gearbox Knob: Selects low gear cal positioning of spindle. It can be zeroed
"L" for maximum torque from 50–1000 RPM, at any position and manually increased or
or high gear "H" for 100–2000 RPM. decreased independent of spindle position
when operation requires it.
B. Drawbar Cap/Drawbar: Drawbar secures
collets and tooling in the spindle. M. Quill Lock Lever: Locks vertical position of
quill when tightened.
C. Z-Axis Handwheel: Raises and lowers head-
stock.
Motors:
Main
Type......................................................................................................................................... High-Torque DC
Horsepower................................................................................................................................ 600W (3/4 HP)
Phase............................................................................................................................................ Single-Phase
Amps............................................................................................................................................................ 10A
Speed................................................................................................................................................ 4500 RPM
Power Transfer ................................................................................................................................. Gear Drive
Bearings....................................................................................................... Shielded and Permanently Sealed
Main Specifications:
Operation Info
Spindle Travel.............................................................................................................................................. 2 in.
Max Distance Spindle to Column.......................................................................................................... 6-5/8 in.
Max Distance Spindle to Table.................................................................................................................... 9 in.
Longitudinal Table Travel (X-Axis)............................................................................................................. 13 in.
Cross Table Travel (Y-Axis).................................................................................................................. 5-1/2 in.
Vertical Head Travel (Z-Axis)................................................................................................................ 8-1/4 in.
Head Tilt (Left/Right)........................................................................................................ Left 45, Right 45 deg.
Drilling Capacity for Cast Iron................................................................................................................... 5/8 in.
Drilling Capacity for Steel......................................................................................................................... 1/2 in.
End Milling Capacity................................................................................................................................. 5/8 in.
Face Milling Capacity................................................................................................................................... 2 in.
Model G0758 The information contained herein is deemed accurate as of 12/3/2014 and represents our most recent product specifications. PAGE 1 OF 2
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
Construction
Spindle Housing/Quill........................................................................................................................... Cast Iron
Table.................................................................................................................................................... Cast Iron
Head.................................................................................................................................................... Cast Iron
Column/Base....................................................................................................................................... Cast Iron
Paint Type/Finish.................................................................................................................................... Enamel
Other
Optional Stand........................................................................................................................................ T26612
Other Specifications:
Country of Origin ................................................................................................................................................ China
Warranty ........................................................................................................................................................... 1 Year
Serial Number Location .................................................................................................................................. ID Label
ISO 9001 Factory .................................................................................................................................................. Yes
CSA, ETL, or UL Certified/Listed ............................................................................................................................ No
Features:
Dovetail headstock column and table ways
High-torque, low-noise DC motor
Variable-speed spindle with DRO
Spindle elevation DRO
3-Axis precision handwheel control
Coarse and fine spindle downfeed
2-Speed gearbox
Zero-setting dials on handwheels
Handwheel dials feature 0.002" graduations
Accessories Included:
Drill chuck 3-16mm with B16 taper
Drill chuck arbor B16 x R8
Open-ended and hex wrenches
Toolbox
Model G0758 The information contained herein is deemed accurate as of 12/3/2014 and represents our most recent product specifications. PAGE 2 OF 2
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
NOTICE This symbol is used to alert the user to useful information about
proper operation of the machine.
OWNER’S MANUAL. Read and understand this ELECTRICAL EQUIPMENT INJURY RISKS. You
owner’s manual BEFORE using machine. can be shocked, burned, or killed by touching live
electrical components or improperly grounded
TRAINED OPERATORS ONLY. Untrained oper- machinery. To reduce this risk, only allow qualified
ators have a higher risk of being hurt or killed. service personnel to do electrical installation or
Only allow trained/supervised people to use this repair work, and always disconnect power before
machine. When machine is not being used, dis- accessing or exposing electrical equipment.
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially DISCONNECT POWER FIRST. Always discon-
around children. Make workshop kid proof! nect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
DANGEROUS ENVIRONMENTS. Do not use This prevents an injury risk from unintended startup
machinery in areas that are wet, cluttered, or have or contact with live electrical components.
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury. EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
MENTAL ALERTNESS REQUIRED. Full mental observing machinery to reduce the risk of eye
alertness is required for safe operation of machin- injury or blindness from flying particles. Everyday
ery. Never operate under the influence of drugs or eyeglasses are NOT approved safety glasses.
alcohol, when tired, or when distracted.
The primary risks of operating a Mill/Drill are as follows: You can be seriously injured or killed
by getting clothing, jewelry, or long hair entangled with rotating cutter. You can be severely cut
or your fingers can be amputated by contacting the rotating cutter. You can be blinded or struck
with great force by broken cutting tools, metal chips, workpieces, or adjustment tools thrown
from the rotating spindle. To reduce your risk of serious injury when operating this machine,
completely heed and understand the following:
UNDERSTAND ALL CONTROLS. Make sure you SECURE WORKPIECE TO TABLE. Clamp
understand the function and proper use of all con- workpiece to table or secure in a vise mounted to
trols before starting. This will help you avoid mak- table, so workpiece cannot unexpectedly shift or
ing mistakes that result in serious injury. spin during operation. NEVER hold workpiece by
hand during operation.
WEAR FACE SHIELD. Always wear a face shield
in addition to safety glasses. This provides more CLEAN MACHINE SAFELY. Metal chips or shav-
complete protection for your face than safety ings can be razor sharp. DO NOT clear chips
glasses alone. by hand or compressed air that can force chips
farther into machine—use a brush or vacuum
REMOVE CHUCK KEY & SPINDLE TOOLS. instead. Never clear chips while spindle is turning.
Always remove chuck key, drawbar wrench, and
other tools used on the spindle immediately after PROPERLY MAINTAIN MACHINE. Keep machine
use. This will prevent them from being thrown by in proper working condition to help ensure that it
the spindle upon startup. functions safely and all guards and other compo-
nents work as intended. Perform routine inspec-
PROPERLY SECURE CUTTER. Firmly secure tions and all necessary maintenance. Never oper-
cutting tool or drill bit so it does not fly out of spin- ate machine with damaged or worn parts that can
dle during operation. break or result in unexpected movement during
operation.
USE CORRECT SPINDLE SPEED. Follow rec-
ommended speeds and feeds for each size and DISCONNECT POWER FIRST. To reduce risk of
type of cutting tool. This helps ensure best cutting electrocution or injury from unexpected startup,
results and avoid tool breakage during operation. make sure mill/drill is turned OFF, disconnected
from power, and all moving parts have come to
INSPECT CUTTING TOOL. Inspect cutting tools a complete stop before changing cutting tools or
for sharpness, chips, or cracks before each use. starting any inspection, adjustment, or mainte-
Replace dull, chipped, or cracked cutting tools nance procedure.
immediately.
POWER DISRUPTION. In the event of a local
ALLOW SPINDLE TO STOP. To minimize your power outage during operation, turn spindle switch
risk of entanglement, always allow spindle to stop OFF to avoid a possible sudden startup once
on its own. DO NOT stop spindle using your hand power is restored.
or any other object.
Like all machinery there is potential danger when operating this machine. Accidents are fre-
quently caused by lack of familiarity or failure to pay attention. Use this machine with respect
and caution to lessen the possibility of operator injury. If normal safety precautions are over-
looked or ignored, serious personal injury may occur.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
Lighting
Children or untrained people
Lighting around the machine must be adequate
may be seriously injured by
enough that operations can be performed safely.
this machine. Only install in an
Shadows, glare, or strobe effects that may distract
access restricted location.
or impede the operator must be eliminated.
21"
193/4"
301/4"
Figure 8. G0758 working clearances.
Lifting
Sling
Vertical
Handwheel
Figure 9. Model T26612 optional stand for
Model G0758.
HEAVY LIFT! 3. Hang sling from forklift fork and place it under
Straining or crushing injury headstock, as shown in Figure 10. DO NOT
may occur from improperly place sling over any controls or against any
lifting machine or some of components that may be damaged from the
its parts. To reduce this risk, force required for lifting.
get help from other people
and use a forklift (or other 4. Unbolt machine from pallet. Have an assis-
lifting equipment) rated for tant on the ground steady machine to prevent
weight of this machine. it from swinging and lift it slightly off the pallet
with forklift.
The base of this machine has mounting holes Use a standard screwdriver to attach handwheel
that allow it to be fastened to a workbench or handles (see Figures 13–14).
other mounting surface to prevent it from moving
during operation and causing accidental injury or
damage.
Table Handwheel
Hex Handles
Bolt
Figure 13. X- and Y-axis handwheel handles
attached.
Flat Washer
Machine Base
Vertical Handwheel Handle
Workbench
Flat Washer
Lock Washer
Hex Nut
Lag Screw
Flat Washer
Machine Base
Workbench
After the arbor is installed in the drill chuck, it Damage caused by running the mill/drill
is very difficult to separate the assembly. If you without first properly lubricating headstock
would like to use a different chuck in the future, gears will not be covered under warranty.
we recommend getting a new arbor for that chuck.
1. Make sure all tools and objects used during 8. Open chip guard half way and press ON but-
setup are cleared away from machine. ton. Machine should not start.
2. Press OFF button (see Figure 16). This —If machine does start (with chip guard
will help prevent unexpected startup when opened half way), press OFF button and
machine is connected to power. immediately disconnect power to machine.
The chip guard safety feature is not work-
ing correctly. This safety feature must
work properly before proceeding with regu-
ON Button
lar operations. Refer to Troubleshooting
table in this manual.
Variable-
Speed Congratulations! The Test Run is complete.
Knob Continue to Spindle Break-In.
OFF Button
7. Press ON button.
The spindle break-in procedure distributes lubri-
cation throughout the bearings to reduce the risk 8. Run machine for a minimum of 10 minutes.
of early bearing failure if there are any "dry" spots
or areas where lubrication has settled in the bear- 9. Without stopping spindle, use variable-speed
ings. You must complete this procedure before knob to run machine at 1000 and 2000 RPM
placing operational loads on the spindle for the for 10 minutes each.
first time when the machine is new or if it has
been sitting idle for longer than 6 months. 10. Press OFF button.
Always start the spindle break-in at the lowest The spindle break-in of the machine is now
speed to minimize wear if there are dry spots. complete!
Allow the spindle to run long enough to warm up
and distribute the bearing grease, then incremen-
tally increase spindle speeds, allowing the spindle
to run the same amount of time at each speed, until Inspections &
reaching the maximum spindle speed. Following
the break-in procedure in this progressive man- Adjustments
ner helps minimize any potential wear that could
occur until lubrication is fully distributed.
The following adjustments were performed at the
factory before the machine was shipped:
2. Press ON button.
Power
Zero
Button
in/mm
Button
v Button
• Travels up and down the column (Z-axis). 1. DISCONNECT MACHINE FROM POWER!
• Tilts 45° left or right relative to the table.
2. Support headstock with one hand, then loos-
Raising/Lowering Headstock en headstock center bolt and angle lock nut
(see Figure 22).
1. DISCONNECT MACHINE FROM POWER!
Vertical
Handwheel
Graduated Dials
The handwheels have graduated dials that are
used to determine table movement in 0.002"
increments, with one full revolution equalling X-Axis
0.100". Table Locks Y-Axis
Table Locks
Rotate graduated dial to a relative starting point
(see Figure 24). Figure 25. X- and Y-axis table travel locks.
Y-Axis Handwheel
The saddle does not have limit stops. To move
the table along the Y-axis, loosen the Y-axis
table locks shown in Figure 25, then use the
handwheel in front of the table in the same man-
ner as the X-axis handwheel.
Figure 24. Graduated dial location.
Drawbar
Tool Slot Adjustment
Nut
Drawbar
Figure 26. 1–13mm drill chuck joined with R-8 Spindle Pin
arbor.
To install tooling:
Drawbar Cap
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
Z-Axis Ways
(1 of 2)
Y-Axis Ways
X-Axis Ways
1. DISCONNECT MACHINE FROM POWER! 1. Remove cap screw and headstock gear
access cover shown in Figure 40.
2. Using Y-axis handwheel, move table as far
forward as possible.
Headstock
Gears
X-Axis Leadscrew
Quill Rack
Lube Type...Model T23964 or NLGI#2 Equivalent
Lube Amount.........................................Thin Coat
Lubrication Frequency.......... 90 hrs. of Operation
Troubleshooting
Symptom Possible Cause Possible Solution
Machine does not 1. Blown fuse in machine. 1. Replace fuse/ ensure there are no shorts.
start or a breaker 2. Chuck guard open. 2. Close guard.
trips. 3. Incorrect power supply voltage. 3. Ensure power supply voltage matches circuit
requirements.
4. Plug/receptacle at fault/wired wrong. 4. Test for good contacts; correct wiring.
5. Power supply circuit breaker tripped or fuse 5. Ensure circuit is sized correctly and free of shorts.
blown. Reset circuit breaker or replace fuse.
6. Motor wires connected incorrectly. 6. Correct motor wiring connections.
7. Wiring is open/has high resistance. 7. Check for broken wires or disconnected/corroded
connections; repair/replace as necessary.
8. Motor brushes at fault. 8. Remove/replace brushes.
9. Chuck guard safety switch at fault. 9. Replace safety switch.
10. Circuit board at fault. 10. Test/replace.
11. Motor at fault. 11. Test/repair/replace.
12. Potentiometer/variable-speed dial at fault. 12. Test/replace.
Machine stalls or is 1. Feed rate/cutting speed too fast. 1. Decrease feed rate/cutting speed.
overloaded. 2. Wrong cutter type. 2. Use correct cutter for task.
3. Machine is undersized for task or tooling is 3. Use smaller or sharper tooling; reduce feed rate or
incorrect for task. spindle speed; use coolant fluid if possible.
4. Motor wired incorrectly. 4. Ensure motor wiring is correct.
5. Motor bearings are at fault. 5. Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
6. Motor has overheated. 6. Clean off motor, let cool, and reduce workload.
7. Motor is at fault. 7. Test/repair/replace motor.
Machine has 1. Motor or machine component is loose. 1. Inspect/replace stripped or damaged bolts/nuts, and
vibration or noisy retighten with thread locking fluid.
operation. 2. Machine is incorrectly mounted or sits 2. Tighten/replace mounting bolts in bench; relocate/
unevenly. shim machine.
3. Motor fan is rubbing on fan cover. 3. Replace dented fan cover or damaged fan.
4. Workpiece not secure. 4. Properly clamp workpiece on table or in vise.
5. Excessive depth of cut. 5. Decrease depth of cut.
6. Cutter/tooling is loose. 6. Make sure tooling is properly secured.
7. Cutter is dull or at fault. 7. Replace/resharpen cutter.
8. Bit is chattering. 8. Replace/sharpen bit; index bit to workpiece; use
appropriate feed rate and cutting RPM.
9. Motor bearings are at fault. 9. Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
DISCONNECT MACHINE FROM POWER The X-axis leadscrew nut shown in Figure 45
BEFORE ADJUSTING THE GIBS! is accessed from underneath the left side of the
table.
Make sure all table locks are loose. Then, loosen
one gib adjustment screw (see Figure 44) and
tighten the opposing screw the same amount to
move the gib, while at the same time using the X-Axis Leadscrew Nut
handwheels to move the table until you feel a Cap Screw
slight drag in that path of movement.
Cap Screw
(1 of 4)
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-
the requirements at the beginning of this man- riencing difficulties understanding the information
ual when connecting your machine to a power included in this section, contact our Technical
source. Support at (570) 546-9663.
Motor
Spindle
RPM
Sensor
Front Panel
Limit Switch
Inside
Bottom
Panel
-38-
RPM
Sensor
Fuse - F10AL250V
Fuse Holder - MF528 10A 250V
JYMC- 22UB-II
ON PAGE 36!
L1
23 13
24 14 L2
A To Plug
KEDU Variable
Speed Dial
KJD17B
120V
A
J2 J1
B
G0758 Wiring
IN N1
G
N
IN
L1
Circuit Board
L
CESX 1101-28
Inside Bottom Panel
Limit Switch
110 VAC
Neutral
KW1-103
15A 125VAC Hot
16(4)A 250 VAC 5-15 Plug
(As Recommended)
Ground
Figure 52. JD-014 circuit board. Figure 55. CESX 1101-28 circuit board.
Figure 53. Spindle RPM sensor. Figure 56. Guard limit switch.
20
29 49
21 77
7
22
23 30
19 19
24 52
54
64 55
66
65 56
68 67
63 50
69 73 61
15 14 62
44
51 51
60 59
38
73 72 75 58
70 40
16
16 71 67
44
57
38 60
74
57 60 51
59
76
40 58
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
94
90
91
94
78
96
80 91
91 86
87
86 81
97 88
83
89
85
84
79
178 108
177 119 120
109
101
183
203
102 184 121
202
110
103
180 179
111 122 131
123 130
112 126
104
124 129
181
105
115 128
113
125
106
114
127
139
111 140
116
107 110
118
117
200 138 173
166
134 175 172
174 170
140 169
176 136
168
137 164 176
152
132 135 171
201
145 153 165 162 167
154 161
143
182 133 151 143
142 163
204 147 157
187 141 144
150 189 160 159
156
195
206 149 158
146
196 205 185
188 190
191 197 155
199
192
193 194 198 148
251
252
253 260
254
261
262
264
263
305
305
312
313
306
306
312
311
311
310
310
307
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
7. Do you think your machine represents a good value? _____ Yes _____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____ Yes _____No
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
Name_______________________________
Street_______________________________
City______________State______Zip______
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.