Professional Documents
Culture Documents
Testrano 600 User Manual ENU PDF
Testrano 600 User Manual ENU PDF
User Manual
TESTRANO 600 User Manual
2 OMICRON
Contents
Contents
Using this manual 7
Safety symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1 Safety instructions 8
1.1 Operator qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Safety standards and rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.1 Safety standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.2 Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.3 Safety accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3 Operating the measurement setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4 Orderly measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5 Disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.6 Compliance statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7 Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 Introduction 13
2.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 Device variants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Hardware overview 14
3.1 TESTRANO 600. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1.1 TESTRANO 600 front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1.2 TESTRANO 600 side panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.3 Safety and warning indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1.4 Emergency Stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1.5 TESTRANO 600 measuring cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2 CP TD1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.1 Grounding terminal and booster input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.2 Serial interface connector and measuring inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.3 High-voltage connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3 Trolley. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4 Functional scheme 23
5 Application 25
5.1 Safety precautions in the substation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2 Preparing the test setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3 Connecting to the transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.4 Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.5 Disconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6 TESTRANO 600 TouchControl 32
6.1 Selecting tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.1.1 Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.1.2 Predefined jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.2 Side bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2.1 Manual test list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2.2 Asset info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.3 Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.4 TouchControl settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.4.1 General settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.5 Software lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7 Testing with TouchControl 39
OMICRON 3
TESTRANO 600 User Manual
4 OMICRON
Contents
OMICRON 5
TESTRANO 600 User Manual
6 OMICRON
Using this manual
DANGER
Death or severe injury will occur if the appropriate safety instructions are not observed.
WARNING
Death or severe injury can occur if the appropriate safety instructions are not observed.
CAUTION
Minor or moderate injury may occur if the appropriate safety instructions are not
observed.
NOTICE
Equipment damage or loss of data possible
OMICRON 7
TESTRANO 600 User Manual
1 Safety instructions
1.1 Operator qualifications
Working on high-voltage assets can be extremely dangerous. Consequently, only personnel qualified,
authorized and skilled in electrical engineering and trained by OMICRON are allowed to operate
TESTRANO 600 and its accessories. Before starting to work, clearly establish the responsibilities.
Personnel receiving training, instructions, directions, or education on TESTRANO 600 must be under
constant supervision of an experienced operator while working with the equipment. The operator is
responsible for the safety requirements during the whole test.
8 OMICRON
Safety instructions
OMICRON 9
TESTRANO 600 User Manual
► Do not operate TESTRANO 600 under ambient conditions that exceed the temperature and humidity
limits listed in chapter 15 "Technical data" on page 218.
► Check any additional equipment (for example, your computer) for environmental conditions before
use.
► Use dry and clean cables. In dusty regions, use protective caps. To avoid leakage current, make sure
that the cables have ground contact.
► Only use cables supplied by OMICRON.
► Position the measurement setup in a way that you can easily disconnect TESTRANO 600 from
mains. If permanently connected, make sure that the measurement setup is positioned in a way that
the switch or circuit breaker can be easily reached.
► Do not operate TESTRANO 600 and its accessories in the presence of explosives, gas or vapors.
► If TESTRANO 600 or its accessories do not seem to function properly (for example, in case of cable
damages, abnormal warming or overheating of components), stop using them and contact
OMICRON support (see "Support" on page 231).
► Observe the high-voltage areas.
► Always obey the internal safety instructions for working in areas with high voltage to avoid injury.
Distance:
min. 1.5 m / 5 ft
Device under test
TESTRANO 600
Figure 1-1: Illustration of safe area and high-voltage area established for working with TESTRANO 600
and CP TD1
10 OMICRON
Safety instructions
TESTRANO 600 and its accessories may be used only as described in this User Manual. Any other use
is not in accordance with the regulations. The manufacturer and the distributor are not liable for damage
resulting from improper use. The user alone assumes all responsibility and risk.
Following the instructions provided in this User Manual is also considered part of being in accordance
with the regulations.
Opening TESTRANO 600 or its accessories invalidates all warranty claims.
1.5 Disclaimer
Using TESTRANO 600 in any way differing from the one mentioned above is considered improper use,
and will invalidate all customer warranty claims and exempt the manufacturer from any liability to
recourse.
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the
equipment may be impaired.
OMICRON 11
TESTRANO 600 User Manual
1.7 Recycling
This test set (including all accessories) is not intended for household use. At
the end of its service life, do not dispose of the test set with household waste!
For customers in EU countries (incl. European Economic Area)
OMICRON test sets are subject to the EU Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE directive). As part of our legal obligations
under this legislation, OMICRON offers to take back the test set and ensure that it is
disposed of by authorized recycling agents.
For customers outside the European Economic Area
Please contact the authorities in charge for the relevant environmental regulations in
your country and dispose the OMICRON test set only in accordance with your local
legal requirements.
12 OMICRON
Introduction
2 Introduction
2.1 Designated use
In combination with the CP TD1 or as a stand-alone unit, TESTRANO 600 is a multi-purpose power
transformer test system for routine and diagnostic testing of power transformers during manufacturing,
commissioning and maintenance.
The various partly automated tests are defined and parameterized via the front panel control of a built-
in embedded PC or via an externally connected laptop.
OMICRON 13
TESTRANO 600 User Manual
3 Hardware overview
3.1 TESTRANO 600
► Refer to user manual chapter 15 "Technical data" on page 218 for detailed hardware information.
14 OMICRON
Hardware overview
Power switch
16A
Resetable mains overcurrent SERIAL Mains power socket (one-phase)
protection Connection to CP TD1
NETWORK
RJ-45 socket for connecting TESTRANO 600 to an external computer
OMICRON 15
TESTRANO 600 User Manual
16 OMICRON
Hardware overview
Warning lights
► Always observe the warning lights while working with TESTRANO 600.
► Do not cover the warning lights during operation.
If no or both warning lights are on, the unit is defective or not supplied by mains.
Beeper
The beeper is an additional indicator for the main device status but does not compensate for the warning
lights on the TESTRANO 600 front and side panel.
If the beeper has been disabled, no acoustical signal will be emitted while the TESTRANO 600 outputs
are active.
► Refer to section "Beeper" on page 37 of this manual on how to disable and activate the beeper.
If the beeper is activated but does not emit a signal for the scenarios listed above in Table 3-1,
TESTRANO 600 might be defective.
► If TESTRANO 600 appears to be defective, do not use it anymore. Contact OMICRON support
(see "Support" on page 231).
OMICRON 17
TESTRANO 600 User Manual
For disconnection:
► Hold the connector and pull back the
silver latch.
► Turn the connector to the left and gently
pull it out.
NOTICE
Equipment damage possible
► Do not pull the cable when disconnecting.
► Hold, turn and gently pull the connector for disconnection.
18 OMICRON
Hardware overview
High-voltage cable
marked red
• Polarity protection: only suitable for
HIGH VOLTAGE and LOW VOLTAGE
sockets
• 15 m length
• 8 poles
• cross-section:
4 × 4 mm2 for output
4 × 1 mm2 for measurement
• Neutrik® plug
Low-voltage cable
marked yellow
OMICRON 19
TESTRANO 600 User Manual
3.2 CP TD1
► Refer to the CP TD1 User Manual for detailed information and safety instructions.
Equipotential ground
terminal
BOOSTER IN
Booster input
SERIAL
Serial interface
connector
IN_B
measuring input
IN_A
measuring input
Grounding terminal
High-voltage output
20 OMICRON
Hardware overview
3.3 Trolley
TESTRANO 600
Cable drum with double-
shielded output cable;
connection to test object
Booster cable TESTRANO 600 ⇔ CP TD1
CP TD1
High-voltage output
Grounding clamp
OMICRON 21
TESTRANO 600 User Manual
3.4 Cleaning
WARNING
Death or severe injury caused by high voltage or current possible
► Do not clean TESTRANO 600, the CP TD1 or any other device when connected to the
test object.
► Disconnect the test object, accessories and connection cables before cleaning.
► Use a cloth dampened with isopropanol alcohol to clean TESTRANO 600 and its accessories.
22 OMICRON
Functional scheme
4 Functional scheme
Vmotor
down
Imotor
Tap
Tap
EN
PE
E1
up
L1
L2
L3
L1
L2
L3
IN
IN
N
N
EXT. HIGH VOLTAGE LOW VOLTAGE
TAP CHANGER
BOOSTER Measure/output Measure/output
measure
measure
output
output
output
measure
3×U
3×U
2×U
Hardware discharge circuit
3xI
Switch matrix Analog-to-digital
converter
Switch mode amplifiers
Control unit
III
II
I
I1
I2
I3
I4
OMICRON 23
TESTRANO 600 User Manual
Terminal Description
Mains interface
L Mains phase
N Mains neutral
PE Equipotential ground
Communication and safety interfaces
I1 1 × external EtherCAT® module
I2 1 × Ethernet
I3 1 × serial
I4 2 × safety
EXTERNAL BOOSTER
E1 External booster phase
EN External booster neutral
PE Equipotential ground
HIGH VOLTAGE
L1 Phase 1 high voltage
L2 Phase 2 high voltage
L3 Phase 3 high voltage
N Neutral high voltage
LOW VOLTAGE
L1 Phase 1 low voltage
L2 Phase 2 low voltage
L3 Phase 3 low voltage
N Neutral low voltage
TAP CHANGER
Tap up Command for upward switching direction
Tap down Command for downward switching direction
Vmotor IN Motor voltage input
Imotor IN Motor current input
24 OMICRON
Application
5 Application
5.1 Safety precautions in the substation
Before setting TESTRANO 600 into operation and carrying out a test, it is essential that you have read
and understood chapter 1 "Safety instructions" on page 8.
► Be aware that all output sockets of TESTRANO 600 can carry life-hazardous voltage and current.
► Only use TESTRANO 600 with a solid connection to ground.
► Separate your working area – see Figure 1-1: "Illustration of safe area and high-voltage area
established for working with TESTRANO 600 and CP TD1" on page 10.
► Tests with high voltages and currents must only be carried out by authorized and qualified personnel.
► Personnel receiving training, instructions, directions, or education on high- voltage/current tests
should remain under the constant supervision of an experienced operator while working with the
equipment.
► The instructions have to be renewed at least once per year.
► The instructions must be available in written form and signed by each person assigned to do high-
voltage/current tests.
Prior to connecting a test object to TESTRANO 600, the following steps need to be carried out by an
authorized employee of the utility:
► Protect yourself and your working environment against an accidental re-connection of high voltage
by other persons and circumstances.
► Verify that the test object is safely isolated.
► Earth-connect and shorten out the test object’s terminals using a grounding set.
► Protect yourself and your working environment with a suitable protection against other (possibly live)
circuits.
► Protect others from accessing the high-voltage area and accidentally touching live parts by setting up
a suitable barrier and, if applicable, warning lights.
► If there is a longer distance between the location of TESTRANO 600 and the area of danger, a
second person with an additional Emergency Stop button is required.
OMICRON 25
TESTRANO 600 User Manual
1. Make sure that the power switch on the TESTRANO 600 side panel is turned off.
2. Press the Emergency Stop button.
3. Connect TESTRANO 600 to:
• equipotential ground: Ground TESTRANO 600 with a cable of at least 6 mm2 cross-section as
close as possible to the operator.
• the computer (optional if TESTRANO 600 is used with TouchControl)
• the mains power supply
Optional
Connect the CP TD1 to TESTRANO 600
a) Connect to ground.
Without trolley:
► Properly connect the TESTRANO 600 and CP TD1 grounding terminals to substation ground.
With trolley (optional):
► Properly connect the TESTRANO 600 and CP TD1 grounding terminals to the trolley’s ground
bar.
► Connect the trolley’s ground bar to earth.
b) Connect the CP TD1 BOOSTER IN to the TESTRANO 600 EXTERNAL BOOSTER using the
booster cable.
c) Connect the CP TD1 SERIAL to TESTRANO 600 SERIAL with the data cable.
Note: The serial cable also provides the power supply for the CP TD1.
26 OMICRON
Application
OMICRON 27
TESTRANO 600 User Manual
1. Connect the test leads to TESTRANO 600 as shown in the wiring diagram and in the order given
below:
TESTRANO 600
00
I. Connect the high-voltage (red), low-voltage (yellow) and tap changer cables to TESTRANO 600.
II. Connect the high-voltage (red) and low-voltage (yellow) cables to the transformer’s main
terminals.
III. Connect the tap changer cable to the appropriate terminals in the control cabinet of the
transformer (see Figure 5-2 below).
IV. Re-connect and turn on the voltage of the tap changer.
Note: If the tap changer control voltage exceeds 42 V, the orange warning light 2 on the side panel will
indicate a hazardous voltage on the TESTRANO 600 inputs (see 3.1.3 "Safety and warning indicators"
on page 16).
28 OMICRON
Application
PE Motor
Up
Down
Tap control
Optional
Connect the CP TD1 to the transformer
If you connected the CP TD1 to TESTRANO 600 (step 4 in section 5.2), connect the IN_A, IN_B and
high-voltage output of the CP TD1 to the transformer.
► Refer to the CP TD1 User Manual for more information on safely connecting the CP TD1 to a device
under test.
2. Erect a barrier separating the safe area from the high-voltage test area (see page 10).
3. Remove the grounding set from the test object.
4. Release the Emergency Stop button.
OMICRON 29
TESTRANO 600 User Manual
5.4 Measurement
TouchControl Primary Test Manager
TouchControl displays the results in the Primary Test Manager displays the results in the
Measurement view of the test. Measurements section of the test.
30 OMICRON
Application
5.5 Disconnection
1. Wait until the green light on the TESTRANO 600 front panel is on and the warning lights on the front
and side panel are off.
Note: If the tap changer control voltage exceeds 42 V, the orange warning light 2 on the side panel
will indicate a hazardous voltage on the TESTRANO 600 inputs (see 3.1.3 "Safety and warning
indicators" on page 16).
► Disconnect the tap changer cable to extinguish warning light 2.
2. Press the Emergency Stop button on the TESTRANO 600 front panel.
DANGER
Death or severe injury caused by high voltage or current
► Never unplug any cables while the measurement is running.
► Only disconnect cables when all of the following apply:
• The red warning light on the front panel is off.
• The warning lights on the side panel are off.
• The green light on the front panel is on.
If all lights on TESTRANO 600 are off, the device is defective or not supplied by mains.
3. To prevent anyone from starting a test, use the Software lock in the TouchControl software (see
chapter 6.5 "Software lock" on page 38) and/or lock your computer.
4. Remove the barrier between the high-voltage area and the safe area.
DANGER
Death or severe injury caused by high voltage or current possible
► Before touching any part of the transformer, ground and short-circuit its terminals using
a grounding set.
5. Disconnect all cables from the transformer.
6. Disconnect all cables from TESTRANO 600 and, if applicable, from the CP TD1.
7. Switch TESTRANO 600 off by pressing the mains power switch on the side panel.
8. Disconnect the mains power cord.
9. Remove the equipotential ground as the last connection that is removed first from TESTRANO 600
and then on the substation side.
OMICRON 31
TESTRANO 600 User Manual
Tap or swipe
left for more
32 OMICRON
TESTRANO 600 TouchControl
6.1.1 Explorer
► Tap Open manual test list in this view or Explorer in the side bar to access the TouchControl
file system for the following options:
• Save, load and move test lists to/from the internal or external memory
• Create, rename, duplicate and delete folders and test lists
► Tap Eject to safely remove the USB drive.
► Long-tap tests to select several.
Note: Test lists cannot be edited or deleted in the explorer as long as they are still open in the manual
test list.
OMICRON 33
TESTRANO 600 User Manual
Table 6-3: Sidebar options for tests in the manual test list
34 OMICRON
TESTRANO 600 TouchControl
Table 6-3: Sidebar options for tests in the manual test list (continued)
Asset
► Tap the Asset type drop-down box to select from the following asset types:
– Two-winding
– Three-winding
– Auto w/o tert: Auto transformer without tertiary winding
– Auto w tert: Auto transformer with tertiary winding
– Voltage regulator
► Enter the Serial number and Manufacturer
Bushing
► Select the number of Bushings from the drop-down box.
► Enter their Serial numbers.
► Tap Copy to all to copy the first serial number to all serial number fields.
OMICRON 35
TESTRANO 600 User Manual
No CP TD1 connected
36 OMICRON
TESTRANO 600 TouchControl
Beeper
TESTRANO 600 is equipped with a beeper emitting an acoustic warning signal while the device is
discharging or the outputs are active. The beeper is an additional indicator for the main device status but
does not compensate for the warning lights on the TESTRANO 600 front and side panel.
► Refer to Table 3-1: "Warning indicators" on page 16 and "Beeper" on page 17 for more information.
If the beeper is set to OFF, no acoustical warning signal will be emitted while the device outputs are
active.
Presentation mode
You can use a VNC client to display the TESTRANO 600 TouchControl on a computer.
► Install a VNC software on your computer.
► Set Presentation mode to ON in the Settings – General view on your TESTRANO 600.
► Connect to the computer using the IP address of your TESTRANO 600 displayed in the OMICRON
Device Browser.
Device self-test
If TouchControl repeatedly displays a hardware error message, we recommend performing a device
self-test. The self-test checks functionality of the TESTRANO 600 hardware components.
► If the self-test passes but the error messages persist, check the wiring.
Note: During the self-test, the Emergency Stop button must be released.
Logging
► Use the drop-down lists Logging level (for software performance) and Device logging level (for
hardware performance) to adjust the settings described in Table 6-6 below.
The logging function provides information to help find the cause for an error in cooperation with an
OMICRON support engineer.
Note: Log files do not contain any personal information.
► Press Download to flash drive to transfer your device’s log files to the connected USB drive.
OMICRON 37
TESTRANO 600 User Manual
38 OMICRON
Testing with TouchControl
Safety instructions
TESTRANO 600 measuring cables
5. Connect to transformer
TESTRANO 600
Application
Wiring diagrams
7. Measurement Measurement
OMICRON 39
TESTRANO 600 User Manual
If mandatory data are missing, the corresponding submenu and the Start button are marked . Once
all necessary information has been entered, the Start button turns green and the test can be performed.
► Tap Copy to all to copy the Winding settings to all tests that have not yet been executed.
OLTC/DETC position
(HV or LV side)
Tap or swipe left to switch to
Measurement view
40 OMICRON
Testing with TouchControl
Entering values
► Tap a box, then use the numpad to enter or correct a value.
► If needed, tap the metric prefixes below after entering a value:
– k for kilo-
– M for mega-
– m for milli-
► Use the slider to increase or decrease the displayed value. Release the slider to stop at the desired
value.
Note: The slider will stop at the minimum/maximum value.
OMICRON 41
TESTRANO 600 User Manual
Switch between
Enter full screen view
views
Test assessment
(see section Assessment)
Tap arrows to sort list in ascending or
descending order
Assessment
► Tap Assess to expand the available assessment states:
42 OMICRON
Testing with TouchControl
Figure 7-3: Wiring diagram for a TTR on a transformer with vector group YNd5
OMICRON 43
TESTRANO 600 User Manual
7.3 Measurement
► Refer to chapter 1 "Safety instructions" on page 8 for detailed information about safe testing.
► If in doubt, contact OMICRON support (see "Support" on page 231).
DANGER
Death or severe injury caused by high voltage or current
► Do not unplug any cables while the measurement is running.
► Only remove cables when all of the following apply to TESTRANO 600:
• The red warning light on the front panel is off.
• The warning lights on the side panel are off.
• The green light on the front panel is on.
If all lights on TESTRANO 600 are off, the device is defective or not supplied by mains.
WARNING
Death or severe injury caused by high voltage or current possible
► Do not enter the high-voltage area during the test.
► Do not touch any part of the transformer before grounding and short-circuiting its
terminals.
1. Tap Start.
44 OMICRON
TouchControl tests
8 TouchControl tests
This chapter lists the tests available for TESTRANO 600 TouchControl.
► For details on safely performing tests, refer to chapters 1 "Safety instructions" on page 8 and
5 "Application" on page 25.
Chapter Page
8.1 Demagnetization 46
8.2 Turns ratio 50
8.3 Winding resistance 54
8.4 Dynamic OLTC-Scan (DRM) 59
8.5 Leakage reactance/Short-circuit impedance 64
8.6 Tan Delta 69
8.7 Exciting current test 73
8.8 High voltage turns ratio 78
8.9 Power losses at low voltage 83
8.10 Quick 86
8.11 Vector group check 89
OMICRON 45
TESTRANO 600 User Manual
8.1 Demagnetization
Whenever a power transformer is isolated from the power system, residual magnetism remains in its
core due to a phase shift. Due to residual magnetism in the core, high inrush currents, up to the
maximum short-circuit current can occur. This puts undesired stress on the transformer when it is
switched back into service. In addition, many diagnostic measurements can be affected by residual
magnetism, making a reliable assessment very difficult.
Therefore, it is recommended to demagnetize the core before switching the transformer back into service
and after DC voltages have been applied during diagnostic testing.
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
► Tap Copy to all to copy the winding and tap changer configuration
Vector group
to all tests that have not yet been executed.
46 OMICRON
TouchControl tests
Option Description
Test settings
Test current ► Enter the maximum test current.
Saturation level Desired saturation level during the demagnetization process.
This value is only adapted in special cases.
Figure 8-2: Demagnetization test – Measurement view with expanded measuring values
OMICRON 47
TESTRANO 600 User Manual
Option Description
Measurement
Measurement name Text field for description or comment
Status During demagnetization:
• Positive saturation running
• Negative saturation running
• Demagnetization running
After demagnetization:
• Demagnetization passed
• Saturation failed
• Demagnetization aborted
I DC Measured current
Min. neg. remanence Maximum remanence in negative direction of the hysteresis curve
Max. pos. remanence Maximum remanence in positive direction of the hysteresis curve
Remanence Measured remanence
Initial remanence Remanence measured at the beginning of the test
Option Description
Initial remanence Measured remanence at the start of the test
Max. pos. remanence Maximum remanence in positive direction of the hysteresis curve
Min. neg. remanence Maximum remanence in negative direction of the hysteresis curve
Remanence Measured remanence
Level Saturation level of the transformer
Max. current Maximum demagnetizing current (TESTRANO 600 output)
Pos. sat. flux Maximum saturation flux in positive direction of the hysteresis curve
Neg. sat. flux Maximum saturation flux in negative direction of the hysteresis curve
Resistance Resistance measured at maximum positive saturation flux
Remaining saturation Saturation remaining in currently running demagnetization cycle
48 OMICRON
TouchControl tests
Option Description
Status During demagnetization:
• Positive saturation running
• Negative saturation running
• Demagnetization running
After demagnetization:
• Demagnetization passed
• Saturation failed
• Demagnetization aborted
Output voltage Current output voltage
Output current Output current
OMICRON 49
TESTRANO 600 User Manual
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
Vector group ► Set the vector group: Tap Select winding configuration.
Rated voltage ► Enter the transformer’s rated voltage.
50 OMICRON
TouchControl tests
Option Description
Tap changer data
► Adjust the tap changer settings by tapping the corresponding icon .
Tap changer No tap changer defined
settings
Tap changer has been defined and will be included in the measurement
► Select which tap changer to include in the measurement if both an OLTC and
Tap changer under
a DETC have been defined.
test
The tap changer under test is marked with a star .
OLTC position OLTC tap position during tap switching on the DETC
DETC position DETC tap position during tap switching on the OLTC
Tap changer settings – Define Tap Changer
► Refer to "Defining a tap changer" on page 41.
Measurement
Standard setting: 3 x 400 V
► Select the 3 x 120 V output mode if an increased magnetizing current is
Output mode
necessary.
► Refer to "AC high range low current" in Table 15-2, page 219.
Test voltage Output voltage
Output frequency:
Test frequency • IEEE: 60 Hz
• IEC: 50 Hz
Automatic tap control
► See "Keeping results" on page 53 for more information.
Select ► Select ON to activate the automatic tap control.
Up ► If automatic tap control is ON, use the Up and Down buttons in the Settings
view to switch between the taps and check if your wiring is correct.
Down
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
OMICRON 51
TESTRANO 600 User Manual
Option Description
Tap Tap under test
Phase Phase under test
Nominal ratio Nominal transformer ratio
V prim (L-L) Output voltage; measured line to line
I prim Measured current on the primary side of the transformer
I phase Measured primary current per phase
V sec (L-L) Secondary voltage; measured line to line
V phase absolute Phase shift of the transformer
V phase deviation Deviation of measurement result from the expected result
Voltage ratio Voltage ratio primary:secondary
TTR Measured transformer turns ratio
52 OMICRON
TouchControl tests
Option Description
VTR Measured voltage ratio
Ratio deviation Deviation of the nominal ratio from the voltage ratio
Current tap position
Up ► If automatic tap control is OFF, use the Up and Down buttons in the
Measurement view to switch taps during measurement.
Down
Show results
V phase ► Choose from the drop-down box which value to display in the table.
► Choose between TTR (transformer turns ratio) and VTR (voltage ratio)
Ratio
to be displayed in the result table.
Option Description
TTR/VTR: Transformer/voltage ratio over tap position
TTR deviation: Ratio deviation over tap position
Plot type
Exciting current: Low-voltage exciting current over tap position
Phase deviation: Phase deviation over tap position
Filter graph ► Select the phases to be displayed in the graph.
Current tap position
Up ► If automatic tap control is OFF, use the Up and Down buttons in the
Measurement view to switch taps during measurement.
Down
Keeping results
Automatic tap control = ON: TouchControl automatically saves results when the Tap time is over.
Automatic tap control = OFF: Tap Keep results to manually save results.
OMICRON 53
TESTRANO 600 User Manual
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
Vector group ► Set the vector group: Tap Select winding configuration.
► Tap the drop-down box to choose between Rated voltage and
Rated voltage Rated current and enter the applicable value.
Rated current Note: With LV as the selected output, you need to specify the rated voltage or
current. Otherwise the output voltage will be limited to 2 V to prevent overvoltage.
► Tap Copy to all to copy the winding and tap changer configuration to all tests that have not yet
been executed.
54 OMICRON
TouchControl tests
Option Description
Tap changer data
► Adjust the tap changer settings by tapping the corresponding icon .
Tap changer No tap changer defined
settings
Tap changer has been defined and will be included in the measurement
► Select which tap changer to include in the measurement if both an OLTC and
Tap changer under
a DETC have been defined.
test
The tap changer under test is marked with a star .
OLTC position The OLTC tap position during tap switching on the DETC
DETC position The DETC tap position during tap switching on the OLTC
Tap changer settings – Define Tap Changer
► Refer to "Defining a tap changer" on page 41.
Measurement
Selected output Selected output cable: HV (red) or LV (yellow)
► See 3.1.5 "TESTRANO 600 measuring cables" on page 18.
Note: With LV as the selected output, you need to specify the rated voltage or
current. Otherwise the output voltage will be limited to 2 V to prevent overvoltage.
16 A @ 340 V
Fast magnetization with elevated voltage
33 A @ 170 V
Output mode
For assets with expected low resistances
100 A @ 56 V
For assets with expectedly very low resistances
Test current Current output during the test
Automatic tap control
► See "Keeping results" on page 58 for more information.
Select ► Select ON to activate the automatic tap control.
Up ► If automatic tap control is ON, use the Up and Down buttons in the Settings
view to switch between the taps and check if your wiring is correct.
Down
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
Up/Down test ► Select ON to activate the automatic change of switching direction after the
first/last tap.
OMICRON 55
TESTRANO 600 User Manual
Option Description
Automatic result
► Select ON to automatically keep measurement results, depending on
Automatic result
Tolerance R dev and the Settling time.
R dev
Δt
Time
Tolerance R dev Tolerance for the deviation of measurement results within the settling time
If during the settling time the deviation remains below the defined
Settling time (Δt)
Tolerance R dev, the result is recorded.
Test conditions
Temperature
► Tap ON to activate temperature correction.
correction
Material ► Select the winding material: copper or aluminium.
Temperature Winding temperature
Reference
Reference temperature for the temperature correction
temperature
Correction factor Temperature correction factor calculated from the values entered above
56 OMICRON
TouchControl tests
Option Description
Tap Tap under test
Phase Output phase
R meas Measured resistance
R dev Percentage deviation among the last 20 values measured.
R corr Corrected measured resistance
Time Time until a stable condition was reached
I DC Measured current
V DC Measured voltage
OMICRON 57
TESTRANO 600 User Manual
Option Description
Current tap position
Up ► If automatic tap control is OFF, use the Up and Down buttons in the
Measurement view to switch taps during measurement.
Down
Selected phase – Table view
► After rewiring, select the next phase and press Start.
Filter graph – Plot view
► Select the phases to be displayed in the graph.
Keeping results
Automatic tap control = ON, Automatic result = ON (by default):
In this mode, taps and phases are switched automatically. TouchControl saves a result when it detects
a value within the Tolerance R dev during the settling time.
Automatic tap control = OFF, Automatic result = ON:
► Select a tap and/or phase.
► Tap Auto keep during the measurement.
TouchControl then automatically saves a result when it detects a value within the Tolerance R dev
during the settling time.
On DETCs TouchControl measures all three phases for the selected tap.
► Tap Keep results to manually save results during the settling time. This might be necessary in case
the results will not stabilize.
58 OMICRON
TouchControl tests
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
Vector group ► Set the vector group: Tap Select winding configuration.
Rated voltage ► Tap the drop-down box to choose between Rated voltage and
Rated current Rated current and enter the applicable value.
OMICRON 59
TESTRANO 600 User Manual
Option Description
► Tap Copy to all to copy the winding and tap changer configuration to all tests that have not yet
been executed.
Tap changer data
► Adjust the tap changer settings by tapping the corresponding icon .
Tap changer No tap changer defined
settings
Tap changer has been defined and will be included in the measurement
► Select which tap changer to include in the measurement if both an OLTC and
Tap changer under
a DETC have been defined.
test
The tap changer under test is marked with a star .
OLTC position The OLTC tap position during tap switching on the DETC
DETC position The DETC tap position during tap switching on the OLTC
Tap changer settings – Define Tap Changer
► Refer to "Defining a tap changer" on page 41.
Test conditions
Temperature
► Tap ON to activate temperature correction.
correction
Material ► Select the winding material: copper or aluminium.
Temperature Winding temperature
Reference
Reference temperature for the temperature correction
temperature
Correction factor Temperature correction factor calculated from the values entered above
Measurement
16 A @ 340 V
Fast magnetization with elevated voltage
33 A @ 170 V
Output mode
For assets with expected low resistances
100 A @ 56 V
For assets with expectedly very low resistances
Test current Current output during the test
Dynamic short-circuit of low-voltage windings on single- and three-phase
transformers.
Dynamic shorting
Only selectable for two- and three-winding transformers with an OLTC on the
high-voltage winding.
Tap control
Automatic control ► Select ON to activate the automatic tap control.
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
60 OMICRON
TouchControl tests
Option Description
Recording time Recording period during the switching cycle
Start tap Start tap position of the test
Stop tap Stop tap position of the test
Up/Down test ► Select ON to activate the automatic change of switching direction after the
first/last tap.
Up ► Use the Up and Down buttons to switch between the taps and check if your
wiring is correct.
Down
Automatic result
In this test, results are saved automatically, depending on Tolerance R dev and
Automatic result
the Settling time.
R dev
Δt
Time
Tolerance R dev Tolerance for the deviation of measurement results within the settling time
If during the settling time the deviation remains below the defined
Settling time (Δt)
Tolerance R dev, the result is recorded.
Motor supply
Record ► Tap ON to record the current and voltage supply to the tap changer motor.
Clamp ratio ► Enter the current clamp’s transformer ratio (current to voltage).
OMICRON 61
TESTRANO 600 User Manual
Plot view
For an easier distinction of the different graphs, select a graph from the Graph legend list, then tap
Color meas. to assign it a color.
Table view
► Tap the arrows in the table head to sort the results by tap or phase number.
If Up/down test is ON, the left-most column displays the switching direction: up or down .
Option Description
Tap Tap under test
Phase Output phase
R meas Measured resistance
R dev Deviation of two successive measurement results at the time the test was
stopped
R corr Temperature-corrected measured resistance
62 OMICRON
TouchControl tests
Option Description
Ripple Percentage deviation between highest and lowest value in the DRM curve
Time Time until a stable condition was reached
I DC Measured current
V DC Measured voltage
OMICRON 63
TESTRANO 600 User Manual
64 OMICRON
TouchControl tests
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
Vector group ► Set the vector group: Tap Select winding configuration.
► Tap Copy to all to copy the winding and tap changer configuration to all tests that have not yet
been executed.
Tap changer data
► Adjust the tap changer settings by tapping the corresponding icon .
Tap changer No tap changer defined
settings
Tap changer has been defined and will be included in the measurement
Tap changer settings – Define Tap Changer
► Refer to "Defining a tap changer" on page 41.
Impedance settings – Define impedances
► Define the tap settings for the short-circuit impedance test. In the Measurement view you will be
able to filter the results for the individual entries in this list, using the Impedance list entry drop-
down box.
Short-circuit Short-circuit impedance of the transformer
impedance Z/uk1
Base power Base power used for calculating the percent values of impedances
Base voltage Base voltage used for calculating the percent values of impedances
OLTC position Tap position of the OLTC corresponding to the impedance value
DETC position Tap position of the DETC corresponding to the impedance value
Measurement
► Select Three phase for a three-phase measurement to compare the results
Test mode to the nameplate data.
► Select Per phase for an in-depth error analysis of the individual phases.
Selected phase ► Select the phase for the Per phase mode.
Test current ► Enter the maximum test current.
Test frequency ► Enter the mains frequency.
Test conditions
Temperature
► Tap ON to activate temperature correction.
correction
Material ► Select the winding material: copper or aluminium.
Temperature Winding temperature
OMICRON 65
TESTRANO 600 User Manual
Option Description
Reference
Reference temperature for the temperature correction
temperature
Correction factor Temperature correction factor calculated from the values entered above
Result view
► Tap ON to display the FRSL results in the Per phase table of the
Show FRSL results
Measurement view.
1. Depending on the Profile selected in Settings – General (see 6.4.1 "General settings" on page 36).
66 OMICRON
TouchControl tests
Option Description
Position Entry selected from the impedance list
Phase Phase under test
I Measured current
V Measured voltage
Phase Phase angle between voltage and current
Rk Real part of the measured Zk
Xk Imaginary part of the measured Zk (short-circuit impedance)
Zk Measured short-circuit impedance
uk/Zk calc1 Calculation based on the Zk value of all three phases
OMICRON 67
TESTRANO 600 User Manual
Option Description
Three phase measurement:
Deviation from the nameplate value entered in the Impedance settings
uk dev / Zk dev1 list
Per phase measurement:
Deviation from uk avg / Zk avg
uk avg / Zk avg1, 2 Average of Zk across all phases
Impedance list entry Tap settings for the short-circuit impedance test
(see "Impedance settings – Define impedances" on page 65)
Selected phase2 ► After rewiring, select the next phase and press Start.
1. Depending on the Profile selected in Settings – General (see 6.4.1 "General settings" on page 36).
2. Only for Per phase test
68 OMICRON
TouchControl tests
Option Description
Measurement
► Set the output frequency for the test/the frequency used to calculate the
Test frequency
sweep.
► Select the type of calculation for the measured results from the drop-
Show results
down list (see Table 8-14: "Tan Delta – Measurement").
OMICRON 69
TESTRANO 600 User Manual
Option Description
Noise suppression
Averaging (no. of points) ► Enter the number of measurement points used for averaging.
Bandwidth ► Select the CP TD1 filter bandwidth from the drop-down list.
If this setting is active, the measurement will not be performed at the Test
frequency set in the Measurement section. TouchControl will instead
measure two values at frequencies below and above the entered Test
Avoid test frequency frequency and calculate the median of those two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Device settings
ON: TESTRANO 600 checks whether the shield of the high-voltage cable
Shield check
is connected.
Beeper ON: The CP TD1 beeper is on during the measurement.
Test conditions
Ambient temperature Ambient temperature on site
Test object temperature Temperature of the test object
Humidity Relative ambient humidity
Weather Weather conditions during the test
Correction factors
Temperature correction ► Tap ON to set the temperature correction factor.
► Tap ON to set the reference voltage for the extrapolation of
Reference voltage
measurement results.
70 OMICRON
TouchControl tests
In the Measurement view, the results are displayed in the Table or Plot view.
► Switch to the Live view to monitor the voltage output V out during measurement.
The Overview lists all measurements.
► Mark a list entry and tap Go to meas. to open the measurement.
Option Description
Table
Mode Measurement mode
Measurement Text field for description or comment
V test Test voltage
Freq. Test frequency
V out Measured output voltage
I out Measured output current
OMICRON 71
TESTRANO 600 User Manual
Option Description
Depending on the Result view
PF/DF1, Cap, watt Power factor/dissipation factor, capacitance and watt losses
losses
Imp. Z Impedance with phase angle
Q power, S power Reactive and apparent power
Cp, Rp Parallel capacitance and parallel resistance
Cp, quality factor Parallel capacitance and quality factor
Ls, Rs Serial inductance and serial resistance
Ls, quality factor Serial inductance and quality factor
Correction factors
Temperature
► Tap ON to activate temperature correction.
correction
Reference voltage Reference voltage for the extrapolation of measurement results
1. Depending on the Profile selected in Settings – General (see6.4.1 "General settings" on page 36).
Measurements – Sweeps
► In the Table view, tap Add to add further measurements (max. 30).
► Tap Add point to add a point to an existing measurement.
The following sweeps are available:
• Frequency sweep CPC template:
Sweep frequencies specified by the CPC 100 test templates
• Frequency sweep OMICRON expertise:
Sweep frequencies dynamically distributed within the CP TD1 frequency range for optimum results
• Voltage sweep OMICRON expertise:
Sweep voltages dynamically distributed within the asset-dependent voltage range for optimum
results
• Manual sweep
72 OMICRON
TouchControl tests
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
Vector group ► Set the vector group: Tap Select winding configuration.
► Tap Copy to all to copy the winding and tap changer configuration to all tests that have not yet
been executed.
OMICRON 73
TESTRANO 600 User Manual
Option Description
Tap changer data
► Adjust the tap changer settings by tapping the corresponding icon .
No tap changer defined
Tap changer settings
Tap changer has been defined and will be included in the
measurement
Tap changer settings – Define Tap Changer
► Refer to "Defining a tap changer" on page 41.
Noise suppression
Averaging (no. of points) ► Enter the number of measurement points used for averaging.
Bandwidth Select the CP TD1 filter bandwidth from the drop-down list.
If this setting is active, the measurement will not be performed at the Test
frequency set in the Measurement section. TouchControl will instead
measure two values at frequencies below and above the entered Test
Avoid test frequency frequency and calculate the median of those two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Device settings
ON: CP TD1 checks whether the shield of the high-voltage cable is
Shield check
connected.
Beeper ON: The CP TD1 beeper is on during the measurement.
Measurement
Test voltage Output voltage
Test mode Test mode for this test: UST-A
Selected phase ► After rewiring, select the next phase and press Start.
Output frequency:
Test frequency • IEEE: 60 Hz
• IEC: 50 Hz
Automatic tap control
► See "Keeping results" on page 53 for more information.
Select ► Select ON to activate the automatic tap control.
Up ► If automatic tap control is ON, use the Up and Down buttons in the
Settings view to switch between the taps and check if your wiring is
Down correct.
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
74 OMICRON
TouchControl tests
Option Description
Start tap Start tap position of the test
Stop tap Stop tap position of the test
Correction factors
► Tap ON to set the reference voltage for the extrapolation of
Reference voltage
measurement results.
OMICRON 75
TESTRANO 600 User Manual
In the Measurement view, the results are displayed in the Table or Plot view.
► Switch to the Live view to monitor the voltage output V out during measurement.
Option Description
Tap Tap under test
Phase Phase under test
► Refer to the wiring diagram for correct wiring after changing the phase.
V out Measured output voltage
I out Measured output current
I phase Measured primary current per phase
Watt losses Measured losses
Reactance Main inductance of the transformer
76 OMICRON
TouchControl tests
Option Description
Tap Tap under test
Phase Phase under test
► Refer to the wiring diagram for correct wiring after changing the phase.
V out Measured output voltage
I out Measured output current
I phase Measured primary current per phase
Watt losses Measured losses
Reactance Main inductance of the transformer
Selected phase
► After rewiring, select the next phase and press Start.
Current tap position
Correction factors
► Tap ON to edit the reference voltage.
OMICRON 77
TESTRANO 600 User Manual
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Tap Yes if you are testing an auto transformer.
Vector group ► Set the vector group: Tap Select winding configuration.
Rated voltage ► Enter the transformer’s rated voltage.
78 OMICRON
TouchControl tests
Option Description
► Tap Copy to all to copy the winding and tap changer configuration to all tests that have not yet
been executed.
Tap changer data
► Adjust the tap changer settings by tapping the corresponding icon .
Tap changer No tap changer defined
settings
Tap changer has been defined and will be included in the measurement
► Select which tap changer to include in the measurement if both an OLTC and
Tap changer under
a DETC have been defined.
test
The tap changer under test is marked with a star .
OLTC position OLTC tap position during tap switching on the DETC
DETC position DETC tap position during tap switching on the OLTC
Tap changer settings – Define Tap Changer
► Refer to "Defining a tap changer" on page 41.
Noise suppression
Averaging ► Enter the number of measurement points used for averaging.
(no. of points)
Bandwidth ► Select the CP TD1 filter bandwidth from the drop-down list.
If this setting is active, the measurement will not be performed at the Test
frequency set in the Measurement section. TouchControl will instead measure
two values at frequencies below and above the entered Test frequency and
Avoid test
calculate the median of those two values.
frequency
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Device settings
ON: The CP TD1 checks whether the shield of the high-voltage cable is
Shield check
connected.
Beeper ON: The CP TD1 beeper is on during the measurement.
Measurement
Test voltage Output voltage
Output frequency:
Test frequency • IEEE: 60 Hz
• IEC: 50 Hz
Test mode Test mode for this test: UST-A
Selected phase ► After rewiring, select the next phase and press Start.
Measurement capacitor
Z abs Absolute impedance value
OMICRON 79
TESTRANO 600 User Manual
Option Description
Z phase Phase angle of the impedance
Automatic tap control
► See "Keeping results" on page 53 for more information.
Select ► Select ON to activate the automatic tap control.
Up ► If automatic tap control is ON, use the Up and Down buttons in the Settings
view to switch between the taps and check if your wiring is correct.
Down
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
80 OMICRON
TouchControl tests
Figure 8-16: High voltage turns ratio test – Measurement view with results
Option Description
Tap Tap under test
Phase Phase under test
Nominal ratio Nominal transformer ratio
V prim Output voltage
I sec Measured current on the secondary side of the transformer
Z sec V prim divided by I sec
Used to calculate the turns ratio
V phase Phase shift between primary and secondary voltage
TTR Measured transformer turns ratio
OMICRON 81
TESTRANO 600 User Manual
Table 8-19: High voltage turns ratio – Measurement, table view (continued)
Option Description
Ratio deviation Deviation of the measured ratio from the nominal ratio
Show results
V phase ► Choose from the drop-down box which value to display in the table.
► Choose between TTR (transformer turns ratio) and VTR (voltage ratio)
Ratio
to be displayed in the result table.
Option Description
TTR/VTR: Transformer/voltage ratio over tap position
Plot type
TTR deviation: Ratio deviation over tap position
Filter graph ► Select the phases to be displayed in the graph.
Show results
V phase ► Choose from the drop-down box which value to display in the table.
► Choose between TTR (transformer turns ratio) and VTR (voltage ratio)
Ratio
to be displayed in the result table.
Option Description
V out Output voltage
I out Output current
Z abs Absolute impedance value
Z phase Phase angle of the impedance
82 OMICRON
TouchControl tests
Option Description
Winding
Vector group ► Select from vector groups YNd11, Yd11 and YNyn0.
OMICRON 83
TESTRANO 600 User Manual
Option Description
Measurement
► After rewiring, select the next phase and press Start.
Selected phase
Only available if Auto shorting is set to OFF.
Test voltage ► Enter the output voltage.
Test frequency ► Enter the mains frequency.
ON: Automatic phase switch and short-circuiting of the phases not under test
Auto shorting OFF: Manual phase switching via the Phase selection buttons and manual
short-circuiting of the phases not under test
84 OMICRON
TouchControl tests
Option Description
Table
Phase under test
Phase
► Refer to the wiring diagram for correct wiring after changing the phase.
V out Measured output voltage
I out Measured output current
I phase Measured current per phase
Watt losses Measured losses
cos φ Power factor
Selected phase
► After rewiring, select the next phase and press Start.
OMICRON 85
TESTRANO 600 User Manual
8.10 Quick
Quick is the most basic mode to operate all of the TESTRANO 600 outputs in a manual-like mode using
TouchControl.
Option Description
Output
Signal mode ► Set AC or DC as output signal.
Output mode ► Select 1-phase or 3-phase voltage (V) or current (A) control from the
drop-down list.
Selected output ► Select the TESTRANO 600 output: HV (red) or LV (yellow)
► See 3.1.5 "TESTRANO 600 measuring cables" on page 18
Magnitude
Equal magnitude ► Tap ON for magnitude distribution to all three phases
(phase shift = 120°)
86 OMICRON
TouchControl tests
Option Description
Test frequency ► Enter the mains frequency
Measurement
Phases Number of phases
HV/LV ► Choose the cable pair for the measurement.
► Choose between line-to-line (L-L) and line-to-neutral (L-N) voltage.
Result table view
► Tap ON/OFF to activate/deactivate the corresponding value in the Result table in the
Measurement view.
OMICRON 87
TESTRANO 600 User Manual
88 OMICRON
TouchControl tests
Option Description
Measurement
Test voltage Maximum output voltage
► Perform the vector group check using the default value.
► If there is no conclusive result, try increasing the test voltage.
Test frequency ► Enter the mains frequency
Option Description
V HV Voltage on high-voltage side
V LV Voltage on low-voltage side
I Measured current on the primary side of the transformer
After the check is completed, TouchControl displays the detected vector group(s).
► If there is no conclusive result, try increasing the test voltage.
► Tap the vector group. TouchControl then transfers it to the Settings view.
You can now determine the Tap changer data – see "Defining a tap changer" on page 41.
► Tap Copy to all to copy the winding and tap changer configuration to all tests that have not yet
been executed.
OMICRON 89
TESTRANO 600 User Manual
90 OMICRON
Primary Test Manager
If you were not able to connect to your TESTRANO 600 and the green light is permanently on, wait a
few seconds, then do one of the following:
► Click More (under the Connect button), then click Refresh (or press F5).
If the TESTRANO 600 device to which you want to connect is not displayed in the list of available
devices, proceed as described in "Manual connection to a test system" on page 106.
Alternatively, you can manage the connection to TESTRANO 600 in the Primary Test Manager status
bar (see 9.6.2 "Status bar" on page 105).
OMICRON 91
TESTRANO 600 User Manual
4. On the navigation bar, click the flag representing the language you want to use.
5. On the navigation bar, click Upgrade, and then click Select file.
6. In the Choose File to Upload window, browse to the upload file. You can find the upload file:
• On the Primary Test Manager DVD at
.\_EmbeddedSoftware\TESTRANO600\embeddedImage.tar
• On the hard disk of your computer at
C:\Program Files (x86)\Common Files\OMICRON\UpgradeImages\CHIMERA\
embeddedImage.tar
7. On the device website, click Start upload.
8. After the upload has finished, TESTRANO 600 reboots automatically.
Note: Depending on the browser you are using you may have to wait for up to 30 seconds for a
response after pressing Start upload. Sometimes a message may appear that the server does not
respond. Ignore this message, after a while the upload will start automatically.
License Description
PTM Standard Manual control mode with tests according to your TESTRANO 600
license. Additional 30 testing days with guided workflow according to your
TESTRANO 600 license.
PTM Advanced Unlimited testing with guided workflow and manual tests according to your
TESTRANO 600 license.
92 OMICRON
Primary Test Manager
OMICRON 93
TESTRANO 600 User Manual
Primary Test Manager processes data of different workflow importance. This is indicated by balloons of
different categories as described in the following table.
94 OMICRON
Primary Test Manager
OMICRON 95
TESTRANO 600 User Manual
Command Action
Home Click Home to move from any view to the home view.
Synchronize1 Click Synchronize to synchronize your local database with the Primary
Test Manager server database
(see 9.6.4 "Data synchronization" on page 107).
Settings Click Settings to open the Settings dialog box
(see "Settings" later in this chapter).
Help Click Help to open the TESTRANO 600 technical documentation and
send data to OMICRON support
(see "Help" on page 103).
About Click About to open the About Primary Test Manager dialog box
(see "About" on page 104).
1. Only enabled with the appropriate license.
Settings
In the Settings dialog box, you can make a number of Primary Test Manager settings to match your
regional conventions, manage the job templates, and set the Primary Test Manager server settings for
data synchronization (see 9.6.4 "Data synchronization" on page 107). To open the Settings dialog box,
click Settings in the title bar.
NOTICE
Equipment damage or loss of data possible
Changing the settings in the Settings dialog box affects all data in Primary Test Manager.
► Only change settings if you are qualified to do so.
► Review your changes before clicking OK.
Note: After changing a setting, you must restart Primary Test Manager for the setting to take effect.
96 OMICRON
Primary Test Manager
General
The General tab lists the general settings of Primary Test Manager.
► To set the Primary Test Manager language, select your preferred language from the Language list.
► To set the logging level, select your preferred level from the Logging PTM and Logging Device lists.
The logging function provides information to help find the cause for an error in cooperation with an
OMICRON support engineer. Logging PTM collects information on PTM while Logging Device
focuses on your device.
Note: Log files do not contain any information about users or devices.
► To set the types of available devices, select the respective check boxes.
OMICRON 97
TESTRANO 600 User Manual
Location settings
In this section you can activate the Use location information check box for Grounding system tests.
Remote control
Certain features of Primary Test Manager can be controlled via the PTMate app. Complete the steps
below to establish the connection between your smartphone and your computer.
1. Activate the Allow remote control via HTTP check box in the Remote control section of the PTM
Settings. Primary Test Manager will establish a Wi-Fi access point.
► If both your smartphone and your computer are already connected to the same Wi-Fi network,
proceed to step 2 below.
► If you are not connected to a Wi-Fi network, press the Start Wi-Fi access point button. PTM will
attempt to create a Wi-Fi access point and refresh the displayed QR code.
Note: If your computer does not support ad hoc Wi-Fi access point creation, you can use an external
Wi-Fi device supporting this functionality or create a hotspot on your smartphone. Be aware that
using a smartphone hotspot can lead to additional costs.
2. Open the PTMate app on your smartphone, go to Settings and scan the QR code displayed in the
Remote control section in PTM.
Primary Test Manager displays status icons in the bottom bar:
Number of active remote connections
Active Wi-Fi access point
Active remote control
98 OMICRON
Primary Test Manager
Profiles
In the Profiles tab, you can set your profile, the default rated frequency, the loss index, the units of your
own profiles, and make the test system settings.
With Primary Test Manager, you can use predefined profiles and create your own profiles for naming
conventions.
Note: Primary Test Manager sets the default profile according to the regional settings of your computer.
► To set a profile, select the profile you want to use from the Profiles list.
To create your own profile:
1. Click Create custom profile.
2. In the Create custom profile dialog box, type the profile name, and then click Create.
3. Under Global settings, set the default rated frequency, the loss index, and your preferred units.
OMICRON 99
TESTRANO 600 User Manual
Profiles: Transformer
4. Under Transformer, set the transformer terminal name schemes and preferences such as the
names of some tests, the oil measure, and the short-circuit impedance abbreviation.
With Primary Test Manager, you can use predefined transformer naming conventions according to the
established standards and create your own terminal name schemes.
► To set a terminal names scheme, select the scheme you want to use from the
Terminal names scheme list.
To create your own terminal names scheme:
1. Click Create custom scheme.
2. In the Enter scheme name dialog box, type the scheme name.
3. Set the transformer terminal names, scheme options, and preferences.
► To delete your own terminal name scheme, select the scheme from the Terminal names scheme
list, and then click Delete current scheme.
100 OMICRON
Primary Test Manager
Templates
In the Templates tab, you can edit, import and export job templates for transformers.
► For information on how to process the templates, see "Processing templates" on page 133.
The right pane of the template workspace displays the template preview.
To manage the job templates, select Transformer from the Display templates for list, and then do one
of the following:
► To assign a template to a different asset type or a phase group, or to edit template properties (name,
comment), click the respective Edit button.
► Press the Delete button to delete templates from the Asset type or Phases list.
► To export a template, select the template, and click the Export button.
► To import a template, click the Import button, then browse to the template you want to import.
► To set a template as favorite, click the star icon .
Note: All future test lists with the same asset and number of phases will by default be loaded with the
tests defined in this favorite template.
OMICRON 101
TESTRANO 600 User Manual
Databases
In the Databases tab you can create, manage and switch between different databases for Primary Test
Manager. Under Properties, you can adjust the server settings for DataSync. For more information,
see "Server settings" on page 108.
102 OMICRON
Primary Test Manager
Help
In the Help dialog box, you can get the relevant information about TESTRANO 600 and data
synchronization, and send data to OMICRON technical support. To open the Help dialog box, click Help
in the title bar.
OMICRON 103
TESTRANO 600 User Manual
About
In the About Primary Test Manager dialog box, you can enter license keys to upgrade your Primary
Test Manager and enhance its functionality by installing additional features. To open the
About Primary Test Manager dialog box, click About in the title bar.
To activate a license:
1. Enter the license key in the About Primary Test Manager dialog box, and then click
Add license key.
The About Primary Test Manager dialog box displays the available licenses and a new
Enter license key box.
2. Repeat step 1 for all license keys you want to enter.
Alternatively, you can enter license keys from files. To a enter a license key from a file, click
Add license from file, and then browse to the file containing the license you want to add.
For detailed information about the Primary Test Manager licensing, contact your OMICRON local sales
representative or distributor.
104 OMICRON
Primary Test Manager
CP TD1
In the status bar, you can connect to and disconnect from a test system, and show and refresh the test
set information.
2. In the Connect to device dialog box, select the test system from the list, and then click Connect.
If you could not connect to your TESTRANO 600 device and the green light is permanently on, wait a
few seconds, and then proceed as follows:
1. Click More beneath the Connect button.
2. Click Refresh.
3. In the Connect to device dialog box, select the test system from the list, and then click Connect.
OMICRON 105
TESTRANO 600 User Manual
After you have connected to the test system, the following dialog box appears.
After you have connected to a test system, right-click the TESTRANO 600 icon in the status bar, then
do one of the following:
► To disconnect from a test system, click Disconnect.
► To display information about the connected test system, click Show test set information.
► To update the test set information, click Refresh test set information.
Note: You can open the Connect to device and the Connected to device dialog boxes also by double-
clicking the TESTRANO 600 icon.
Device self-test
If Primary Test Manager repeatedly displays a hardware error message, we recommend performing a
device self-test. The self-test checks functionality of the TESTRANO 600 hardware components.
► If the self-test passes but the error messages persist, check the wiring.
Note: During the self-test, the Emergency Stop button must be released.
106 OMICRON
Primary Test Manager
2. In the Host or IP box, type tts://a.b.c.d, where a.b.c.d is the static IP address of the device.
OMICRON 107
TESTRANO 600 User Manual
The data synchronization is partial data replication based on subscriptions, that is, all local data is
synchronized with the server database and selected data on the server is synchronized with the local
database.
Server settings
Before synchronizing the Primary Test Manager databases for the first time, you need to set the server
settings.
1. In the title bar, click Settings and select the Databases tab.
The next step depends on the data synchronization method you use: DataSync via web server or
DataSync on premises.
108 OMICRON
Primary Test Manager
Managing subscriptions
You can select data on the server which you want to synchronize with your local data by managing
subscriptions. To manage subscriptions:
1. In the home view (see Figure 9-2: "Primary Test Manager home view" on page 94), click the Manage
button .
2. In the manage view, click Manage subscriptions on the top of the workspace.
3. In the Subscriptions dialog box, select the data on the server you want to synchronize with your local
data.
You can synchronize the data anytime.
► To synchronize the data, click Synchronize in the title bar.
After that, Primary Test Manager shows the synchronization progress.
OMICRON 109
TESTRANO 600 User Manual
Database synchronization
► To synchronize the local Primary Test Manager database with the server database, click
Synchronize in the title bar of the Manage view.
Primary Test Manager then displays the synchronization progress.
Note: You can synchronize databases at any time, as long as a connection to the server database is
available.
When the database synchronization is complete, the locations, assets, and jobs (objects) newly added
to the local database are marked with blue dots in the manage view. You can sort the objects by this
column. As soon as you open an object, its blue dot is removed. All blue dots are removed when you
perform another database synchronization.
9.7 Jobs
When creating a new job, Primary Test Manager leads you through the guided test workflow.
► To open the create new job view, click the Create new job button in the home view.
A job contains all relevant information about the location, the asset under test, and the tests. With
Primary Test Manager, you can process jobs as separate entities. During the guided test workflow, the
job status displayed in the left pane of the create new job view changes. The following table describes
the job statuses.
Status Description
New Location has been defined.
Prepared Asset has been defined.
Partially executed At least one measurement has been executed.
Executed All tests of the job have been executed.
Approved Job has been approved.
110 OMICRON
Primary Test Manager
To navigate through the test workflow, click the navigation buttons in the left pane of the create new job
view.
Note: You can interrupt the test workflow and return to any view at any time by clicking the
corresponding navigation button.
By using the commands on the menu bar, you can process jobs. The following table describes the
available operations.
Command Action
Close Closes a job displayed in the create new job view and leads you back to
home or manage view respectively.
Save job Saves the job displayed in the create new job view.
Copy test Adds another test of the same kind and with the same settings to the test
list. Results are not copied.
Take screenshot Takes screenshot of the selected area of the Primary Test Manager
workspace. The screenshot appears as attachment in the General area
and can be attached to the test report (see 9.7.10 "Test reports" on
page 142).
For more information about operations on the jobs, see 9.8 "Manage objects" on page 144.
OMICRON 111
TESTRANO 600 User Manual
Job data
The following table describes the job data.
Data Description
Name/WO1 Name of the job or work order
(by default generated by Primary Test Manager)
Creation date Date the job was created
Execution date Date the job was executed
Tested by Person who performed the test
Approved by Person who approved the test
Approval date Date the job was approved (see "Approving jobs" later in this section)
1. Mandatory data
112 OMICRON
Primary Test Manager
Approving jobs
If the job data displayed in the job overview has been approved, you can set the approval date of the job.
To set the job approval date, click Approve.
Note: After approving a job, some settings cannot be edited anymore.
Assessment summary
In the Tests area of the job overview, the Result state and Assessment status of test results are
displayed.
► Use the Overall Assessment combo box to manually characterize the asset's condition for reporting
purposes.
Status Description
Fail The status was automatically set to Fail by Primary Test Manager.
Manual fail The status was manually set to Fail.
Investigate The status was automatically set to Investigate by Primary Test
Manager.
Manual investigate The status was manually set to Investigate.
Pass The status was automatically set to Pass by Primary Test Manager.
Partial pass Some measurements have not been assessed.
Manual pass The status was manually set to Pass.
Manual partial pass Some measurements have not been assessed and at least one
assessment status was changed manually.
Not assessed The measurement has not been assessed.
Not rated The status was automatically set to Not Rated by Primary Test
Manager.
Managing attachments
Under Attachments, you can manage attachments to the job overview.
To add an attachment to the job overview:
1. Click the Add button .
2. In the Select Files dialog box, browse to the file you want to attach to the job overview.
To open an attachment, do one of the following:
► Select the attachment, and then click the Open button .
► Double click the attachment.
To delete an attachment from the job overview:
1. Select the attachment you want to delete.
2. Click the Remove button .
OMICRON 113
TESTRANO 600 User Manual
114 OMICRON
Primary Test Manager
► To load the location data available in Primary Test Manager, click Load existing location, and then
select the location you want to load in the Select Location dialog box.
In the Select Location dialog box, you can search for locations (see "Search for objects" on page 145).
In the location view, you can enter addresses of, for example, a client, owner or utility.
► To enter additional addresses, click Add address under Additional addresses.
2. In the Edit Coordinates dialog box, enter the latitude and longitude of the location.
OMICRON 115
TESTRANO 600 User Manual
Managing attachments
Under Attachments, you can manage attachments to locations.
To add an attachment to a location:
1. Click the Add button .
2. In the Select Files dialog box, browse to the file you want to attach to the location.
To open an attachment, do one of the following:
► Select the attachment, and then click the Open button .
► Double click the attachment.
To delete an attachment from a location:
1. Select the attachment you want to delete.
2. Click the Remove button .
116 OMICRON
Primary Test Manager
The asset view depends on the asset you want to specify with Primary Test Manager. To specify an
asset, do one of the following:
► Enter the asset data. The asset data includes the general asset data common to all assets
(see "General asset data" on page 118 and the asset-specific data described in chapter 11 "PTM
Asset data" on page 152).
Note: If you enter location or asset data for a prepared job that differ from those of the master location
or master asset, a notification bar will be displayed. In this case, choose between the following options:
► To import the previously defined location or asset data to this job, click Import from master
location or Import from master asset in the notification bar.
► To update the previously defined location or asset data with the data you have entered for this job,
click Update master location or Update master asset in the notification bar.
► For more information on operations on the jobs, see 9.8 "Manage objects" on page 144.
► To load the asset data available in Primary Test Manager, click Load existing asset, and then select
the asset you want to load in the Select Asset dialog box.
In the Select Asset dialog box, you can search for assets (see "Search for objects" on page 145) and
sort them alphabetically or in the chronological order.
OMICRON 117
TESTRANO 600 User Manual
Data Description
Asset1 Asset under test
Asset type Type of the asset
Serial no.1 Serial number of the asset
Manufacturer Manufacturer of the asset
Manufacturer type Type of the asset according to the manufacturer
Manufacturing year Year of the asset’s manufacturing
Asset system code Code of the asset used by the maintenance planning systems
Apparatus ID Identifier of the asset
Feeder Feeder the asset is connected to
Phase2 Phase the asset is connected to
1. Mandatory data
2. Only available for current transformers, voltage transformers and miscellaneous assets.
Managing attachments
Under Attachments, you can manage attachments to assets.
To add an attachment to an asset:
1. Click the Add button .
2. In the Select Files dialog box, browse to the file you want to attach to the asset.
To open an attachment, do one of the following:
► Select the attachment, and then click the Open button .
► Double click the attachment.
To delete an attachment from an asset:
1. Select the attachment you want to delete.
2. Click the Remove button .
118 OMICRON
Primary Test Manager
Transformer view
In the transformer view, you can specify transformers and assets associated with the transformer such
as bushings, tap changers, and surge arresters.
Specifying a transformer
1. From the Asset list, select Transformer.
2. From the Asset type list, select the type of the transformer.
OMICRON 119
TESTRANO 600 User Manual
Note: Primary Test Manager sets the vector group of an autotransformer without tertiary winding
automatically.
120 OMICRON
Primary Test Manager
Specifying a bushing
1. From the Asset type list, select the type of the bushing.
2. Enter the bushing data (see 11.2 "Spare bushing data" on page 155).
Under Copy bushing data, you can copy data of a bushing to other bushings. To copy the bushing data,
select the respective bushings from the From and To lists, and then click Copy.
OMICRON 121
TESTRANO 600 User Manual
122 OMICRON
Primary Test Manager
OMICRON 123
TESTRANO 600 User Manual
DGA Trending
DGA Trending is a licensed feature that visualizes a transformer’s historic Oil analysis data in various
charts and offers a comparison of data recorded at different points in time.
Refer to 14.1 "Oil Analysis" on page 210 for more detailed information on the Oil analysis test.
3. In the spare bushing view, enter the general asset data (see Table 9-12: "General asset data" on
page 118).
4. Enter the spare bushing data (see 11.2 "Spare bushing data" on page 155).
124 OMICRON
Primary Test Manager
Selecting tests
The test view is divided into the Available tests area, the Selected tests area, and the General test
settings area.
Click the button labeled with the test system with which you want to perform the test on the top of the
Available tests area. Then Primary Test Manager displays the available guided tests and optional
manual tests supported for the selected test system and the asset under test.
► To display the guided tests grouped in categories, click the Show test categories button . .
You can select tests for different test systems supported by Primary Test Manager within the same job.
The symbol indicates the tests not available for the connected test system to signal to you that you
need to connect another test system before proceeding to execute the job.
The optional manual tests are asset-independent. You can perform the tests for any asset described in
this User Manual, but Primary Test Manager does not guide you through the tests and provides no test
settings data.
► For more information about the manual tests, see 9.7.8 "Create new manual tests" on page 140.
OMICRON 125
TESTRANO 600 User Manual
The Selected tests area displays the tests you want to perform. By default, Primary Test Manager
displays the tests recommended by OMICRON. To add a test into the Selected tests area, click the
symbol next to the test name in the Available tests area. To add all tests of a category into the
Selected tests area, click the symbol. The Selected tests area displays the test to be performed in
the recommended order. You can change the order of the tests by dragging them or by using the and
buttons. To remove a test from the Selected tests area, click the symbol next to the test name.
The General test settings area displays the reason of the job, the global test conditions, and some asset
specific data.
Grouping tests
You can group tests from the Selected tests column in the Tests view of a job.
1. In the Selected tests area, select the check boxes next to the tests you want to group. Only
groupable tests are displayed with a check box.
2. Click the Group tests button .
The test groups are then displayed under Tests in the left pane of the test view.
► To rename the test group, double-click the test group name.
► To remove a test from the test group, click the Ungroup button next to the test name.
► To remove a test group from the Selected tests area and from the left pane, click Remove the
selected test next to the test group name.
► To open a test group, click the test group name in the left pane of the test view.
The test group view lists Settings and conditions that are common for all tests in this group.
► In the group’s Test control section, press Start all to start the listed tests in sequence. You can stop
measurements and then press Start to start individual measurements or Resume all to resume the
grouped tests in sequence.
Importing tests
In the test view, you can import tests performed with TESTRANO 600 and even with the test systems
not currently supported by Primary Test Manager. Primary Test Manager supports import of tests of the
following formats.
You can also import tests in JPG, PDF and any Microsoft Office file format.
126 OMICRON
Primary Test Manager
4. In the workspace of the test view, you can change the test title and the test type.
5. To open the test, click the Open button under Test data.
Note: To open a test, you must have installed the associated application software on your computer.
6. You can attach files as described earlier in this chapter and add comments to the test.
For information about importing and exporting jobs, see "Import and export jobs" on page 149.
OMICRON 127
TESTRANO 600 User Manual
Performing tests
To perform a test:
1. Add the tests you want to perform into the selected tests area (see "Selecting tests" on page 125).
2. In the left pane of the test view, click the test you want to perform.
The test view is then split into the General pane, the Settings and conditions pane, the Measurements
pane and, if automatic assessment is available for the test, the Assessment pane. You can expand
and collapse the panes by clicking the arrows on the split bars.
3. In the Settings and conditions pane, enter the test settings (see the chapter on the asset tests later
in this manual).
128 OMICRON
Primary Test Manager
4. In the Assessment pane, enter the automatic assessment parameters and limits, if applicable.
OMICRON 129
TESTRANO 600 User Manual
5. Connect the test setup to the asset under test according to the wiring diagram displayed in the
General pane. For information about connecting the test setup to the asset under test, see
chapter 5 "Application" on page 25.
As soon as you connect TESTRANO 600 to PTM, the tap switch command in the bottom bar is available.
You can use the arrow buttons to switch a connected OLTC when no measurement is running.
130 OMICRON
Primary Test Manager
DANGER
Death or severe injury caused by high voltage or current
The flashing lightning symbol in the Primary Test Manager test view indicates that an
output of TESTRANO 600 is active.
► Do not touch any outputs or cables while the lightning symbol is displayed.
► If in doubt, press the Emergency Stop button.
OMICRON 131
TESTRANO 600 User Manual
After the measurement has been finished, Primary Test Manager displays the numeric measurement
data and the automatic assessment, if available, in the Measurements pane. To view graphical diagrams
of the measurement results, click the Plot tab.
8. Repeat steps 6 and 7 for all test measurements.
Note: Some tests support starting all measurements at once by clicking the Start all button.
Note: After the test has been performed some asset data relevant for the test configuration cannot be
edited anymore.
132 OMICRON
Primary Test Manager
Processing templates
In the guided test workflow, you can save jobs as templates and open the saved templates. With the help
of templates, you can configure jobs according to your needs (for example, for repeated routines), and
then repeatedly perform tests you only have to define once.
When you create a new job, the favorite template for the corresponding asset type and number of phases
is loaded automatically, if available.
To save a job as template:
1. In the guided test workflow, configure a job.
2. In the Selected tests area of the test view, click Save as template.
OMICRON 133
TESTRANO 600 User Manual
To open a template:
1. In the Selected tests area of the test view, click Open template.
2. In the Choose Template dialog box, select the asset type, the number of phases and the template
you want to open.
Note: If you added a Microsoft Excel report template to the job template, its location is displayed
under Customized Excel report template.
3. Press Replace existing testplan to replace the tests already listed in the test list.
Press Append to existing testplan to add the tests listed in the template to the end of the existing
testplan.
Note: If you click Append to existing testplan, the Microsoft Excel report template will not be added
the selected job template to the currently opened job.
134 OMICRON
Primary Test Manager
In the chart, measurements performed with 10 kV at rated frequency are displayed as circles . All other
data are displayed as triangles .
Note: If several tests are performed on one day, the most recent test of that day is connected to the
curve in the Trending chart. The others are displayed in the same chart but are not connected.
Status Description
Fail The status was automatically set to Fail by Primary Test Manager.
Manual fail The status was manually set to Fail.
Investigate The status was automatically set to Investigate by Primary Test
Manager.
Manual investigate The status was manually set to Investigate.
Pass The status was automatically set to Pass by Primary Test Manager.
Manual pass The status was manually set to Pass.
Not assessed The measurement has not been assessed.
Not rated The status was automatically set to Not Rated by Primary Test
Manager.
OMICRON 135
TESTRANO 600 User Manual
Comparing results
Some tests support comparison of the graphical diagrams of measurement results. The comparison data
is an integral part of the tests. You can compare tests for different assets but we recommend to perform
only comparisons of tests for the same assets or assets of the same design type. Primary Test Manager
offers you only tests of the same type for which the comparison is possible.
To compare a test with a test available in the database:
1. In the Measurements pane of a test, click the + Select comparison button, if available.
2. In the Select a test window, select the test you want to compare with the current test.
136 OMICRON
Primary Test Manager
3. The Measurements pane displays the measurement results of the selected test.
OMICRON 137
TESTRANO 600 User Manual
6. Primary Test Manager displays the measurement results of both tests in real time.
138 OMICRON
Primary Test Manager
2. In the Execute prepared job view, click Open job from file.
3. In the Open dialog box, browse to the .ptm file you want to import.
4. Import the job, and then go through the guided test workflow.
► See 9.7.1 "Guided test workflow" on page 110.
To execute a prepared job available in Primary Test Manager:
1. In the home view, click the Execute prepared job button .
2. In the Execute prepared job view, search for the job you want to execute.
► See "Search for objects" on page 145.
3. Open the job, and then go through the guided test workflow.
► See 9.7.1 "Guided test workflow" on page 110.
OMICRON 139
TESTRANO 600 User Manual
The workspace of the create new manual tests view depends on the selected button in the left pane (see
Figure 9-42: "Left-pane buttons" on page 141). Initially, the workspace is divided into the
Available tests area and the Selected tests areas.
On top of the Available tests area you can select the test system you want to use for measurement.
Primary Test Manager displays all available manual tests supported for the selected test system.
140 OMICRON
Primary Test Manager
Note: You can change the default test names. To rename a test, click the corresponding button in the
left pane, and then click the test name.
OMICRON 141
TESTRANO 600 User Manual
The report view is divided into the New report area, the Settings area and the Existing reports area.
In the New report area, you can set the report data. The following table describes the report data.
Data Description
Title Title of the report. Appears as the report header.
Report language Language the report is created in
Report ID1 Identifier of the report
Client Customer for which the report is designated
Logo Logo to appear in the report
(see "Setting the logo" later in this chapter)
Summary Text field to summarize the content of the test report in own words.
1. By default generated by Primary Test Manager.
142 OMICRON
Primary Test Manager
OMICRON 143
TESTRANO 600 User Manual
Note: The mounted assets are displayed in italics. To hide them, expand the Search area under Asset,
and then select the Hide mounted assets check box.
The manage view displays the objects in a hierarchical structure as follows:
• If you select a location, the manage view displays the assets, jobs, and reports associated with the
selected location.
• If you select an asset, the manage view displays the jobs and reports associated with the selected
asset.
• If you select a job, the manage view displays the reports associated with the selected job.
You can sort the objects alphabetically or in the chronological order.
► Drag and drop the column headers to rearrange the columns.
144 OMICRON
Primary Test Manager
Data Description
Asset Asset under test
Asset type Type of the asset
Serial no. Serial number of the asset
Manufacturer Manufacturer of the asset
Manufacturer type Type of the asset according to the manufacturer
Asset system code Code of the asset used by the maintenance planning systems
Apparatus ID Identifier of the asset
Data Description
Name/WO Name of the job or work order
Tested by Person who performed the test
Executed between Time period between the job was executed
Status Status of the job
OMICRON 145
TESTRANO 600 User Manual
Data Description
Name Name of the report
Client Customer for which the report is designated
Created between Time period between the report was created
146 OMICRON
Primary Test Manager
Duplicate assets
In the manage view, you can duplicate assets available in Primary Test Manager. To duplicate an asset:
1. From the asset list, select the asset you want to duplicate.
2. Click the Duplicate button .
3. In the asset view, type the serial number(s) of the new asset.
OMICRON 147
TESTRANO 600 User Manual
Relocate assets
In the manage view, you can relocate assets available in Primary Test Manager. To relocate an asset:
1. From the asset list, select the asset you want to relocate.
2. Click the Relocate button .
3. In the Relocate Asset dialog box, select the location you want to move the asset to.
4. If the asset you want to relocate is mountable, select an asset where the moved asset is to be
mounted.
Note: You can filter the locations and assets by searching for keywords (see "Search for objects" on
page 145).
148 OMICRON
Primary Test Manager
OMICRON 149
TESTRANO 600 User Manual
Location view
4. Location and asset
Asset view
5. Jobs Jobs
Test view
PTM Transformer tests
6. Tests
PTM Bushing tests
Device-independent PTM tests
Safety instructions
TESTRANO 600 measuring cables
7. Connection to device under test
TESTRANO 600
Application
Connecting to the transformer
8. Test settings Performing tests
150 OMICRON
Testing with Primary Test Manager
10.2 Measurement
► Refer to chapter 1 "Safety instructions" on page 8 for detailed information about safe testing.
► If in doubt, contact OMICRON support (see "Support" on page 231).
DANGER
Death or severe injury caused by high voltage or current
► Do not unplug any cables while the measurement is running.
► Only remove cables when all of the following apply to TESTRANO 600:
• The red warning light on the front panel is off.
• The warning lights on the side panel are off.
• The green light on the front panel is on.
If all lights on TESTRANO 600 are off, the device is defective or not supplied by mains.
WARNING
Death or severe injury caused by high voltage or current possible
► Do not enter the high-voltage area during the test.
► Do not touch any part of the transformer before grounding and short-circuiting its
terminals.
OMICRON 151
TESTRANO 600 User Manual
Data Description
Phases Number of transformer phases
Vector group Vector group of the transformer
(see "Setting the vector group of a transformer" on page 120)
Unsupported vector group Vector group not supported by Primary Test Manager as text for
(for documentation) documentation
Data Description
Rated frequency Rated frequency of the transformer
Voltage ratings
Winding Transformer’s winding
Voltage L-L L-L voltage of the transformer’s winding
Voltage L-N L-N voltage of the transformer’s winding
Insul. level L-L (BIL) L-L basic impulse level rating of the transformer’s winding
Power ratings
Rated power Power rating of the transformer
Cooling class Cooling class of the transformer
Temp. rise wind. Temperature rise of the transformer’s winding
Current ratings at rated power
H/X/Y1 Maximum power frequency current of the transformer at rated power
Short-circuit rating
Max. short-circuit current Maximum short-circuit current of the transformer in kA during a given time
in seconds
1. Set by the regional conventions (see "Settings" on page 96).
152 OMICRON
PTM Asset data
Data Description
Ref. temp. Reference temperature
Short-circuit impedances H - X1, H - Y1, X - Y1
Short-circuit impedance Short-circuit impedance of the transformer
Z (%)1
Base power Base power used for calculating the percent values of impedances
Base voltage Base voltage used for calculating the percent values of impedances
Load losses Pk Load loss at the transformer’s rated load
OLTC position Tap position of the OLTC
DETC position Tap position of the DETC
Zero sequence impedance
Base power Base power used for calculating the percent values of impedances
Base voltage Base voltage used for calculating the percent values of impedances
Winding Transformer’s winding
Zero sequence Zero sequence impedance of the transformer
impedance Z0 (%)
1. Set by the regional conventions (see "Settings" on page 96).
Data Description
Category Application category of the transformer
Status Usage status of the transformer
Tank type Type of transformer tank
Insulation medium Insulation medium of the transformer
Weight Weight of transformer insulation
Insulation
Volume Volume of transformer insulation
Total weight Total weight of the transformer
Winding Transformer’s winding
Conductor material Conductor material of the transformer’s winding
OMICRON 153
TESTRANO 600 User Manual
Data Description
OLTC/DETC Select the OLTC check box to set the OLTC data.
Select the DETC check box to set the DETC data.
Tap changer configuration
Winding Transformer’s winding to which the tap changer is connected
Tap scheme Notation scheme for tap identification
No. of taps Number of the tap changer’s taps
Current tap position1 Current position of the tap
Voltage table
Tap Number of the tap
Voltage Voltage on the tap
1. Only available for the DETC
Data Description
Ratings
Units in stack Number of the surge arrester’s units
Numerical positions Select the Numerical positions check box to set numerical positions of the
surge arrester.
Literal positions Select the Literal positions check box to set alphabetical positions of the surge
arrester.
Position Position of the surge arrester
Serial no. Serial number of the surge arrester
Voltage L-L Values needed to calculate the maximum test voltages
Voltage L-N
MCOV rating Maximum continuous operating voltage between the terminals of the surge
arrester
Unit catalog no. Identifier of the surge arrester unit
154 OMICRON
PTM Asset data
Data Description
Pos.1 Terminal of the transformer’s winding to which the spare bushing is
connected
Ratings
Rated frequency Rated frequency of the spare bushing
Insul. level LL (BIL) L-L basic impulse level rating of the spare bushing
Voltage L-ground Rated line-to-ground voltage
Max. system voltage Maximum voltage between phases during normal service
Rated current Rating current of the spare bushing
Manufacturer info
Catalog no. Catalog number of the spare bushing
Drawing no. Drawing number of the spare bushing
Style no. Style number of the spare bushing
Nominal values
PF (C1)/ Power factor, dissipation factor, or tangent delta of the capacitance C1
DF (C1)/ between the top of the spare bushing and the voltage/test tap
Tanδ (C1)2
Cap. (C1) Capacitance C1 between the top of the spare bushing and the voltage/test
tap
PF (C2)/ Power factor, dissipation factor, or tangent delta of the capacitance C2
DF (C2)/ between the voltage/test tap of the spare bushing and ground
Tanδ (C2)2
Cap. (C2) Capacitance C2 between the voltage/test tap of the spare bushing and
ground
OMICRON 155
TESTRANO 600 User Manual
Data Description
Other
Insulation type Insulation type of the spare bushing
Outer insulation type Outer insulation type of the spare bushing
1. Only available for spare bushings mounted on another assets
2. Set by the regional conventions (see "Settings" on page 96).
156 OMICRON
PTM Transformer tests
Note: The chapters list the available options and settings for the tests. Depending on the individual asset
and the general Primary Test Manager settings, not every test displays all listed items.
OMICRON 157
TESTRANO 600 User Manual
► For information on how to group tests and execute them in sequence, refer to "Grouping tests" on
page 126.
1. Depending on the Profile selected in Settings – Profiles (see "Profiles" on page 99).
158 OMICRON
PTM Transformer tests
The table below lists common parameters for the PF/DF/Tanδ tests.
Note: Some tests do not comprise all parameters listed below.
Option Description
Measurement settings
Test frequency ► Set the output frequency for the test.
Show results ► Select the results you want to display.
All measurement results are stored and displayed when
selected from the list.
Sweep settings
Frequency sweep Sweep profile:
None, OMICRON expertise (recommended), or
CPC template
• None: no frequency sweep
• OMICRON expertise: sweep frequencies dynamically
distributed within the TESTRANO 600 frequency range
for optimum results
• CPC template: sweep frequencies specified by the
CPC 100 test templates
Voltage sweep (tip-up) Sweep profile:
None or OMICRON expertise
• None: no voltage sweep
• OMICRON expertise: sweep voltages dynamically
distributed within the asset-dependent voltage range for
optimum results
Sweep profiles ► Click the pen button to create a frequency or voltage
sweep profile.
► Add up to 30 measurement points with individual output
voltages or frequencies. Double-click a value to change
it.
► Mark a favorite to use it as the default sweep profile
for future tests.
Note: The predefined profiles None, OMICRON expertise
and CPC template cannot be edited or deleted.
The default sweep profiles for this test are:
• Frequency sweep: OMICRON expertise
• Voltage sweep: None
Noise suppression settings
Averaging (no. points) Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
OMICRON 159
TESTRANO 600 User Manual
Option Description
If this setting is active, the measurement will not be
performed at the Test frequency set in the Measurement
section. Primary Test Manager will instead measure two
values at frequencies below and above the entered Test
Avoid test frequency frequency and calculate the median of those two values.
The Avoid test frequency setting is predefined for the
selected test.
► Only change the default setting for special applications.
Device settings
Enable shield check ► Activate the check box if you want TESTRANO 600 to
check whether the shield of the high-voltage cable is
connected.
Use beeper ► Activate the check box to activate the CP TD1 beeper
during the measurement.
Test conditions
Custom test conditions ► Activate the check box to set test conditions differing
from the global test conditions.
Top oil temperature ► Enter the temperature of the oil from the top of the
transformer tank.
Bottom oil temperature ► Enter the temperature of the oil from the bottom of the
transformer tank.
Average oil temperature Calculated average oil temperature in the tank
Winding temperature ► Enter the winding temperature.
Ambient temperature ► Enter the ambient temperature on site.
Humidity ► Enter the relative ambient humidity on site.
Weather ► Select the weather conditions during the test.
Correction factors
Temperature correction ► Activate the check box to use temperature correction for
this test.
Correction factor Temperature correction factor
Use reference voltage ► Activate the check box to extrapolate the I out and Watt
losses results for the specified reference voltage.
Reference voltage Reference voltage for extrapolation of the measurement
results
Bushings compensation ► Activate the check box to compensate the effect of the
capacitance C1 of the transformer’s bushings on the
measurement results of the test.
160 OMICRON
PTM Transformer tests
Option Description
Table
Measurement Arrangement of the measurement
Test mode ► Select a test mode from the drop-down list.
V test Test voltage
Freq. Test frequency
V out Measured output voltage
I out Measured output current
Watt losses Measured losses
PF meas Measured power factor
PF corr Corrected power factor
Cap. meas Measured capacitance
Assessment Measurement assessment
OMICRON 161
TESTRANO 600 User Manual
Option Description
Measurement settings
Test voltage Output voltage
Test mode Test mode for this test: UST-A
Noise suppression
Averaging Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
162 OMICRON
PTM Transformer tests
Option Description
If this setting is active, the measurement will not be performed at the
Test frequency set in the Measurement section. Primary Test
Manager will instead measure two values at frequencies below and
above the entered Test frequency and calculate the median of those
Avoid test frequency
two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Tap changer settings
Tap changer under test ► Select which tap changer to include in the measurement if both an
OLTC and a DETC have been defined.
Tap control settings
Automatic tap control ► Activate the check box to use automatic tap control during the test.
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
Option Description
Tap Tap under test
Phase Phase under test
V out Output voltage
I out Excitation current
I phase Measured primary current per phase
Watt losses Measured losses
Reactance Main inductance of the transformer
Assessment Measurement assessment
OMICRON 163
TESTRANO 600 User Manual
Option Description
Measurement capacitor
Z abs Absolute impedance value
Z phase Phase angle of the impedance
164 OMICRON
PTM Transformer tests
Option Description
Measurement settings
Test voltage ► Enter the output voltage.
Ratio ► Choose between transformer turns ratio (TTR) and voltage ratio
(VTR).
Test mode Test mode for this test: UST-A
Noise suppression
Averaging Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
If this setting is active, the measurement will not be performed at the
Test frequency set in the Measurement section. Primary Test
Manager will instead measure two values at frequencies below and
above the entered Test frequency and calculate the median of those
Avoid test frequency
two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Device settings
Enable shield check ► Activate the check box if you want TESTRANO 600 to check
whether the shield of the high-voltage cable is connected.
Use beeper ► Activate the check box to activate the CP TD1 beeper during the
measurement.
Tap changer settings
Tap changer under test ► Select which tap changer to include in the measurement if both an
OLTC and a DETC have been defined.
Tap control settings
Automatic tap control ► Activate the check box to use automatic tap control during the test.
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
Option Description
Capacitor
Test voltage Output voltage
Test mode ► Select a test mode from the drop-down list
V out Measured output voltage
OMICRON 165
TESTRANO 600 User Manual
Option Description
I out Measured output current
Z abs Absolute impedance value
Z phase Phase angle of the impedance
Table
Phase selection ► After rewiring, select the next phase and press Start.
Tap Tap under test
Phase Phase under test
Nominal ratio Nominal transformer ratio
V prim Output voltage
I sec Measured current on the secondary side of the transformer
Z sec V prim divided by I sec
Used to calculate the turns ratio
V phase Phase shift of the transformer
TTR Measured transformer turns ratio
VTR Measured voltage ratio
Ratio dev Deviation of the nominal ratio from the voltage ratio
Assessment Measurement assessment
166 OMICRON
PTM Transformer tests
OMICRON 167
TESTRANO 600 User Manual
Option Description
Measurement settings
Test current ► Enter the maximum test current.
Test conditions
Temperature correction ► Activate the check box to use temperature correction for
this test.
Winding material Conductor material of the transformer’s winding
Winding temp. Temperature of the transformer’s winding
Reference temp. Reference temperature to be used for temperature
correction
Correction factor Temperature correction factor
Option Description
Limits schema ► Select a standard from the drop-down box or set your
own limits schema by selecting Customer specific
limits.
Assess during measurements ► Activate the Assess during measurements check box
to assess the test while the measurements are running.
Option Description
Three phase The Three phase measurement is performed to compare
the results to the nameplate data.
Per phase The Per phase measurement is performed for an in-depth
error analysis of the individual phases.
Short-circuit impedance entry / Tap settings for the short-circuit impedance test
Leakage reactance entry
Show FRSL results1 ► Activate the check box to display the FRSL results in the
Per phase table.
Phase Phase under test
I Measured current
U Measured voltage
V phase Phase angle between voltage and current
Rk Real part of the measured Zk
Xk Imaginary part of the measured Zk (short-circuit
impedance)
Zk Measured short-circuit impedance
168 OMICRON
PTM Transformer tests
Option Description
uk calc / Zk calc1 Short-circuit impedance when IEC profile is active
OMICRON 169
TESTRANO 600 User Manual
Option Description
Measurement settings
Output mode Standard setting: 3 x 400 V
► Select the 3 x 120 V output mode if an increased
magnetizing current is necessary.
► Refer to "AC high range low current" in Table 15-2,
page 219.
Test voltage Output voltage
Ratio ► Choose between TTR (transformer turns ratio) and VTR
(voltage turns ratio) to be displayed in the
Measurements table.
V phase Phase shift of the transformer
170 OMICRON
PTM Transformer tests
Option Description
Tap changer settings
Tap changer under test ► Select which tap changer to include in the measurement
if both an OLTC and a DETC have been defined.
DETC position DETC tap position during tap switching on the OLTC
OLTC position OLTC tap position during tap switching on the DETC
Tap control settings
► Activate the check box to use automatic tap control
Automatic tap control
during the test.
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
Option Description
Limits schema ► Select a standard from the drop-down box or set your
own limits schema by selecting Customer specific
limits.
Assess during measurements ► Activate the Assess during measurements check box
to assess the test while the measurements are running.
Option Description
Table
Tap Tap under test
Phase Phase under test
Nominal ratio Nominal transformer ratio
V prim Output voltage
I prim Excitation current
I phase Measured primary current per phase
V sec Secondary voltage
V phase Phase angle of the measured secondary voltage
OMICRON 171
TESTRANO 600 User Manual
Option Description
TTR Measured transformer turns ratio
VTR Measured voltage turns ratio
Ratio dev Deviation of the nominal ratio from the voltage ratio
Assessment Measurement assessment
172 OMICRON
PTM Transformer tests
Option Description
Measurement settings
16 A @ 340 V
fast magnetization with elevated Voltage
33 A @ 170 V
Output mode for assets with expected low resistances
100 A @ 56 V
for assets with very low resistance
► Refer to the wiring diagram for rewiring.
Test current Current output during the test
Tap changer settings
Tap changer under test Tap changer actuated during the test
OMICRON 173
TESTRANO 600 User Manual
Option Description
DETC position DETC tap position during tap switching on the OLTC
OLTC position OLTC tap position during tap switching on the DETC
Tap control settings1
► Activate the check box to activate the automatic tap
Automatic tap control
control.
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
► Activate the check box for the automatic change of
Up/Down test
switching direction after the first/last tap.
Result settings
► Select ON to automatically keep measurement results,
Automatic result
depending on tolerance R dev and the settling time.
R dev
Δt
Time
174 OMICRON
PTM Transformer tests
Option Description
Winding material Conductor material of the transformer’s winding
Winding temp. Temperature of the transformer’s winding
Reference temp. Reference temperature to be used for temperature
correction
Correction factor Temperature correction factor
1. Only for OLTC
Option Description
Table
Tap Tap changer position
Phase Output phase
R meas Measured resistance
R dev Deviation of two successive measurement results at the
time the test was stopped
R corr Corrected measured resistance
Time Time between the start and stop of a measurement
I DC Measured current
V DC Measured voltage
Assessment Measurement assessment
OMICRON 175
TESTRANO 600 User Manual
Option Description
Measurement settings
Output mode DC current output of TESTRANO 600
Test current Current output during the test
Dynamic short-circuit of low-voltage windings on single- and three-phase
transformers.
Dynamic shorting
Only selectable for two- and three-winding transformers with an OLTC on
the high-voltage winding.
Motor supply
► Activate the check box to record the current and voltage supply to the
Record motor supply
tap changer motor.
Clamp ratio ► Enter the current clamp’s transformer ratio (current to voltage).
176 OMICRON
PTM Transformer tests
Option Description
Tap control settings
Automatic tap control Taps are switched automatically during this measurement
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
► Activate the check box for the automatic change of switching direction
Up/Down test
after the first/last tap.
Result settings
Settling time (∆t) Time during which the deviation of measurement results is evaluated. If
the deviation is below the defined tolerance R dev, the result is recorded.
Tolerance R dev Tolerance for the deviation of measurement results within the settling time.
Recording time Recording period during the switching cycle
Test conditions
Temperature correction ► Activate the check box to use temperature correction for this test.
Winding material Conductor material of the transformer’s winding
Winding temperature Temperature of the transformer’s winding
Reference temperature Reference temperature to be used for temperature correction
Correction factor Temperature correction factor
Option Description
Table
Tap Tap changer position
Phase Output phase
R meas Measured resistance
Deviation of two successive measurement results at the time the test was
R dev
stopped
R corr Temperature-corrected measured resistance
Ripple Percentage deviation between highest and lowest value in the DRM curve
Time Time between the start and stop of a measurement
I DC Measured current
V DC Measured voltage
Assessment Measurement assessment
OMICRON 177
TESTRANO 600 User Manual
Option Description
ΔI [A] Difference in current values [amperes]
Δt [ms] Time difference [milliseconds]
ΔU [V] Difference in voltage values [volts]
178 OMICRON
PTM Transformer tests
12.8 Demagnetization
Whenever a power transformer is isolated from the power system, residual magnetism remains in its
core due to a phase shift. Due to residual magnetism in the core, high inrush currents, up to the
maximum short-circuit current can occur. This puts undesired stress on the transformer when it is
switched back into service. In addition, many diagnostic measurements can be affected by residual
magnetism, making a reliable assessment very difficult.
Therefore, it is recommended to demagnetize the core before switching the transformer back into service
and after DC voltages have been applied during diagnostic testing.
Option Description
Measurement settings
Test current ► Set the current injected during the test.
Saturation criteria
Saturation level Desired saturation level during the demagnetization process.
This value is only adapted in special cases.
OMICRON 179
TESTRANO 600 User Manual
Option Description
Measurement
Measurement Text field for description or comment
Status During demagnetization:
• Positive saturation running
• Negative saturation running
• Demagnetization running
After demagnetization:
• Demagnetization passed
• Saturation failed
• Demagnetization aborted
I DC Measured current
Min. neg. remanence Maximum remanence in negative direction of the hysteresis curve
Max. pos. remanence Maximum remanence in positive direction of the hysteresis curve
Remanence Measured remanence
Initial remanence Measured remanence at the start of the test
Option Description
Measurement settings
Test voltage Maximum output voltage
► Perform the vector group check using the default value.
► If there is no conclusive result, try increasing the test voltage.
After the check is completed, PTM displays the detected vector group(s) in the Measurements section.
► If there is no conclusive result, try increasing the test voltage.
► Press Copy to asset to apply the suggested vector group to the Winding configuration of the asset.
180 OMICRON
PTM Transformer tests
Option Description
Vector group
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Edit Vector Group ► Set the vector group.
Test settings
Test current ► Enter the maximum test current.
Saturation level Desired saturation level during the demagnetization process.
This value is only adapted in special cases.
OMICRON 181
TESTRANO 600 User Manual
Option Description
Measurement settings
Test current ► Enter the maximum test current.
Saturation criteria
Saturation level Desired saturation level during the demagnetization process.
This value is only adapted in special cases.
Option Description
Measurement
Measurement name Text field for description or comment
Status During demagnetization:
• Positive saturation running
• Negative saturation running
• Demagnetization running
After demagnetization:
• Demagnetization passed
• Saturation failed
• Demagnetization aborted
I DC Measured current
Min. neg. remanence Maximum remanence in negative direction of the hysteresis curve
Max. pos. remanence Maximum remanence in positive direction of the hysteresis curve
Remanence Measured remanence
Initial remanence Measured remanence at the start of the test
Assessment Measurement assessment
182 OMICRON
PTM Transformer tests
Table 12-25: Power losses at low voltage test – Settings and conditions
Option Description
Winding
Vector group ► Select from vector groups YNd11, Yd11 and YNyn0.
Measurement settings
Test voltage ► Enter the output voltage.
Test frequency ► Enter the mains frequency.
On: Automatic phase switch and short-circuiting of the phases not under test
Auto shorting Off: Manual phase switching via the Phase selection buttons and manual short-
circuiting of the phases not under test
OMICRON 183
TESTRANO 600 User Manual
Option Description
Phase selection
► After rewiring, select the next phase and press Start.
Table
Phase under test
Phase
► Refer to the wiring diagram for correct wiring after changing the phase.
V out Measured output voltage
I out Measured output current
I phase Measured current per phase
Watt losses Measured losses
cos φ Power factor
184 OMICRON
PTM Transformer tests
Option Description
Winding
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Edit Vector Group ► Set the vector group.
Rated voltage ► Enter the transformer’s rated voltage.
Tap changer data
OLTC ► Activate the check box to select the tap changer and enter the corresponding
DETC data.
Winding ► Select the tap changer’s position.
Tap scheme ► Select the notation scheme for tap identification from the drop-down box.
No. of taps ► Enter the number of taps.
Current tap position ► Select the currently active tap.
Rated voltage
Primary ► Enter the transformer’s rated voltage on the primary side.
OMICRON 185
TESTRANO 600 User Manual
Option Description
Secondary ► Enter the transformer’s rated voltage on the secondary side.
Voltage table
Voltage ► Enter the reference voltage for each tap or use the calculation.
Calculate ► Refer to "Specifying an on-load tap changer (OLTC)" on page 122.
Option Description
Measurement settings
Output mode ► Select the output mode from the drop-down list.
Test voltage Output voltage during the test
Test frequency Output frequency during the test
V phase Phase shift of the transformer
Tap changer settings
Tap changer under ► Select which tap changer to include in the measurement if both an OLTC and
test a DETC have been defined.
DETC position DETC tap position during tap switching on the OLTC
OLTC position OLTC tap position during tap switching on the DETC
Tap control settings1
Automatic tap
► Activate the check box to activate the automatic tap control.
control
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
1. Only for OLTC
Option Description
Tap Tap under test
Phase Phase under test
Nominal ratio Nominal transformer ratio
V prim Output voltage
I prim Measured current on the primary side of the transformer
V sec Secondary voltage
V phase Phase shift of the transformer
186 OMICRON
PTM Transformer tests
Option Description
TTR Measured transformer turns ratio
VTR Measured voltage ratio
Ratio deviation Deviation of the nominal ratio from the voltage ratio
Assessment Measurement assessment
OMICRON 187
TESTRANO 600 User Manual
Option Description
Vector group
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Edit Vector Group ► Set the vector group.
Tap changer data
OLTC ► Activate the check box to select the tap changer and enter the
DETC corresponding data.
188 OMICRON
PTM Transformer tests
Option Description
No. of taps ► Enter the number of taps.
Current tap position ► Select the currently active tap.
Rated voltage
Primary ► Enter the transformer’s rated voltage on the primary side.
Secondary ► Enter the transformer’s rated votlage on the secondary side.
Option Description
Measurement settings
Test voltage Output voltage during the test
Test frequency Output frequency during the test
Test mode Test mode for this test: UST-A
Noise suppression
Averaging Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
If this setting is active, the measurement will not be performed at the Test
frequency set in the Measurement section. Primary Test Manager will
instead measure two values at frequencies below and above the entered
Avoid test frequency Test frequency and calculate the median of those two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Option Description
Phase Phase under test
V out Output voltage
I out Excitation current
I phase Measured primary current per phase
Watt losses Measured losses
Reactance Main inductance of the transformer
Assessment Measurement assessment
OMICRON 189
TESTRANO 600 User Manual
Option Description
Vector group
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Edit Vector Group ► Set the vector group.
Rated voltage
Primary ► Enter the transformer’s rated voltage on the primary side.
Secondary ► Enter the transformer’s rated voltage on the secondary side.
Tap changer data
OLTC ► Activate the check box to select the tap changer and enter the corresponding
DETC data.
Winding ► Select the tap changer’s position.
Tap scheme ► Select the notation scheme for tap identification from the drop-down box.
190 OMICRON
PTM Transformer tests
Option Description
No. of taps ► Enter the number of taps.
Voltage table
Voltage ► Enter the reference voltage for each tap or use the calculation.
Calculate ► Refer to "Specifying an on-load tap changer (OLTC)" on page 122.
Option Description
Measurement settings
Test voltage ► Enter the output voltage.
Test frequency ► Enter the output frequency during the test.
Ratio ► Choose between transformer turns ratio (TTR) and voltage ratio
(VTR).
Test mode Test mode for this test: UST-A
Noise suppression
Averaging Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
If this setting is active, the measurement will not be performed at the
Test frequency set in the Measurement section. Primary Test
Manager will instead measure two values at frequencies below and
above the entered Test frequency and calculate the median of those
Avoid test frequency
two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
Device settings
Enable shield check ► Activate the check box if you want TESTRANO 600 to check
whether the shield of the high-voltage cable is connected.
Use beeper ► Activate the check box to activate the CP TD1 beeper during the
measurement.
Tap changer settings
Tap changer under test ► Select which tap changer to include in the measurement if both an
OLTC and a DETC have been defined.
DETC position DETC tap position during tap switching on the OLTC
OLTC position OLTC tap position during tap switching on the DETC
OMICRON 191
TESTRANO 600 User Manual
Option Description
Tap Tap under test
Phase Phase under test
Nominal ratio Nominal transformer ratio
V prim Output voltage
I sec Measured current on the primary side of the transformer
Z sec V prim divided by I sec
Used to calculate the turns ratio
V phase Phase shift of the transformer
TTR Measured transformer turns ratio
VTR Measured voltage ratio
Ratio dev Deviation of the nominal ratio from the voltage ratio
Assessment Measurement assessment
192 OMICRON
PTM Transformer tests
Option Description
Vector group
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Vector group ► Set the vector group.
Rated current
► Select the value you want to specify for Primary and Secondary.
Rated voltage
Primary ► Enter the transformer’s rated current/voltage on the primary side.
Secondary ► Enter the transformer’s rated current/voltage on the secondary side.
Tap changer data
OLTC ► Activate the check box to select the tap changer and enter the corresponding
DETC data.
Winding ► Select the tap changer’s position.
Tap scheme ► Select the notation scheme for tap identification from the drop-down box.
No. of taps ► Enter the number of taps.
OMICRON 193
TESTRANO 600 User Manual
Option Description
Current tap position ► Select the currently active tap.
Voltage table
Voltage ► Enter the reference voltage for each tap or use the calculation.
Calculate ► Refer to "Specifying an on-load tap changer (OLTC)" on page 122.
Option Description
Measurement settings
Output side ► Select the transformer side for the current output.
Output mode ► Select the output mode from the drop-down list.
Test current ► Enter the output current for the test.
Tap changer settings
Tap changer under ► Select which tap changer to include in the measurement if both an OLTC and
test a DETC have been defined.
DETC position DETC tap position during tap switching on the OLTC
OLTC position OLTC tap position during tap switching on the DETC
Tap control settings1
Automatic tap
► Select ON to activate the automatic tap control.
control
Tap time Time for the change between two tap positions
Impulse time Duration of the impulse triggering the tap change
Start tap Start tap position of the test
Stop tap Stop tap position of the test
► Activate the check box for the automatic change of switching direction after
Up/Down test
the first/last tap.
194 OMICRON
PTM Transformer tests
Table 12-37: Manual DC winding resistance test – Settings and conditions (continued)
Option Description
Result settings
► Activate the check box to automatically keep measurement results,
Automatic result
depending on tolerance R dev and the settling time.
R dev
Δt
Time
Tolerance R dev Tolerance for the deviation of measurement results within the settling time
If during the settling time the deviation remains below the defined
Settling time (Δt)
Tolerance R dev, the result is recorded.
Test conditions
Temperature
► Select the check box to activate temperature correction.
correction
Winding material ► Select the winding material: copper or aluminium.
Winding temp. Temperature of the transformer windings.
Reference temp. Reference temperature for the temperature correction
Correction factor Temperature correction factor calculated from the values entered above
1. Only for OLTC
Option Description
Tap Tap under test
Phase Output phase
R meas Measured resistance
R dev Deviation of two successive measurement results at the time the test was
stopped
R corr Corrected measured resistance
OMICRON 195
TESTRANO 600 User Manual
Option Description
Time Time until a stable condition was reached
I DC Measured current
V DC Measured voltage
Assessment Measurement assessment
196 OMICRON
PTM Transformer tests
Option Description
Vector group
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Edit Vector Group ► Set the vector group.
Rated current
► Select the value you want to specify for Primary and Secondary.
Rated voltage
Primary ► Enter the transformer’s rated current/voltage on the primary side.
Secondary ► Enter the transformer’s rated current/voltage on the secondary side.
OMICRON 197
TESTRANO 600 User Manual
Option Description
Tap changer data
OLTC ► Activate the check box to select the tap changer and enter the
DETC corresponding data.
Winding ► Select the tap changer’s position.
► Select the notation scheme for tap identification from the drop-down
Tap scheme
box.
No. of taps ► Enter the number of taps.
Current tap position ► Select the currently active tap.
198 OMICRON
PTM Transformer tests
Note: The name of this test depends on the standard set in the Settings view (see 6.4 "TouchControl
settings" on page 36):
• According to the IEEE standard: Leakage Reactance
• According to IEC standard: Short-Circuit Impedance
Option Description
Vector group
Phases ► Set the number of transformer phases.
Auto transformer ► Activate the check box if you are testing an auto transformer.
Edit Vector Group ► Set the vector group.
Rated voltage ► Enter the transformer’s rated voltage.
Tap changer data
OLTC ► Activate the check box to select the tap changer and enter the corresponding
DETC data.
OMICRON 199
TESTRANO 600 User Manual
Option Description
Winding ► Select the tap changer’s position.
Tap scheme ► Select the notation scheme for tap identification from the drop-down box.
No. of taps ► Enter the number of taps.
Current tap position ► Select the currently active tap.
Voltage table
Voltage ► Enter the reference voltage for each tap or use the calculation.
Calculate ► Refer to "Specifying an on-load tap changer (OLTC)" on page 122.
Short circuit impedance data
► Define the tap settings for the short-circuit impedance test. In the Measurements view you will be
able to filter the results for the individual entries in this list, using the Short-circuit impedance entry
drop-down box.
Short-circuit Short-circuit impedance of the transformer
impedance Z/uk1
Base power Base power used for calculating the percent values of impedances
Base voltage Base voltage used for calculating the percent values of impedances
OLTC position Tap position of the OLTC corresponding to the impedance value
DETC position Tap position of the DETC corresponding to the impedance value
1. Depending on the Profile selected in Settings – General (see6.4.1 "General settings" on page 36).
Option Description
Measurement settings
Test current Current output during the test.
Default frequency ► Enter the mains frequency.
Test conditions
Temperature
► Select the check box to activate temperature correction.
correction
Winding material ► Select the winding material: copper or aluminium.
Winding temp. Temperature of the transformer windings.
Reference temp. Reference temperature for the temperature correction
Correction factor Temperature correction factor calculated from the values entered above
200 OMICRON
PTM Transformer tests
Option Description
Three phase The Three phase measurement is performed to compare the
results to the nameplate data.
Per phase The Per phase measurement is performed for an in-depth error
analysis of the individual phases.
Short-circuit impedance entry / Tap settings for the short-circuit impedance test
Leakage reactance entry
Phase selection2 ► Select the phase for the Per phase mode.
Show FRSL results2 ► Activate the check box to display the FRSL results in the Per
phase table.
Position Short-circuit impedance entry
Phase Phase under test
I Measured current
U Measured voltage
V phase Phase shift of the transformer
Rk Real part of the measured Zk
Xk Imaginary part of the measured Zk (short-circuit impedance)
Zk Measured short-circuit impedance
uk calc / Zk calc1 Short-circuit impedance when IEC profile is active
uk dev / Zk dev2 Deviation from the nameplate value entered in the Impedance
settings list
Assessment Measurement assessment
1. Depending on the Profile selected in Settings – Profiles (see "Profiles" on page 99).
2. Only for Per phase test
OMICRON 201
TESTRANO 600 User Manual
202 OMICRON
PTM Transformer tests
Table 12-43: Manual Tan delta test – Settings and conditions (continued)
Option Description
Device settings
Enable shield check ► Activate the check box if you want TESTRANO 600 to
check whether the shield of the high-voltage cable is
connected.
Use beeper ► Activate the check box to activate the CP TD1 beeper
during the measurement.
Test conditions
Ambient temperature ► Enter the ambient temperature on site.
Test object temperature ► Enter the test object’s temperature.
Humidity ► Enter the relative ambient humidity on site.
Weather ► Select the weather conditions during the test.
Correction factors
Temperature correction ► Activate the check box to use temperature correction for
this test.
Correction factor Temperature correction factor
Use reference voltage ► Activate the check box to extrapolate the I out and Watt
losses results for the specified reference voltage.
Reference voltage Reference voltage for extrapolation of the measurement
results
Bushings compensation ► Activate the check box to compensate the effect of the
capacitance C1 of the transformer’s bushings on the
measurement results of the test.
OMICRON 203
TESTRANO 600 User Manual
Option Description
Measurement settings
Test voltage Maximum output voltage
► Perform the vector group check using the default value.
► If there is no conclusive result, try increasing the test voltage.
Test frequency ► Enter the mains frequency
After the check is completed, PTM displays the detected vector group(s) in the Measurements section.
► If there is no conclusive result, try increasing the test voltage.
204 OMICRON
PTM Transformer tests
Option Description
Output
Signal mode ► Set AC or DC as output signal.
Output mode ► Select 1-phase or 3-phase voltage (V) or current (A) control from
the drop-down list.
Selected output ► Select the TESTRANO 600 output: HV (red) or LV (yellow).
► See 3.1.5 "TESTRANO 600 measuring cables" on page 18
Magnitude
Equal magnitude ► Activate the check box for magnitude distribution to all three
phases
(phase shift = 120°)
Test frequency Output frequency during the test
OMICRON 205
TESTRANO 600 User Manual
Option Description
Measurement
Phase Number of phases
HV ► Choose the cable pair for the measurement.
LV ► Choose between line-to-line (L-L) and line-to-neutral (L-N) voltage.
206 OMICRON
PTM Bushing tests
OMICRON 207
TESTRANO 600 User Manual
The following table describes the parameters for spare bushing tests.
Note: Some tests do not comprise all parameters listed below.
Setting Description
Measurement settings
Test frequency Test frequency
Sweep settings
Frequency sweep Sweep profile:
None, OMICRON expertise (recommended), or CPC template
• None: no frequency sweep
• OMICRON expertise: sweep frequencies dynamically distributed
within the CPC 100 frequency range for optimum results
• CPC template: sweep frequencies specified by the CPC 100 test
templates
Voltage sweep (tip-up) Sweep profile:
None or OMICRON expertise
• None: no voltage sweep
• OMICRON expertise: sweep voltages dynamically distributed within
the asset-dependent voltage range for optimum results
Sweep profiles ► Click the pen button to create a frequency or voltage sweep
profile.
► Add up to 30 measurement points with individual output voltages or
frequencies. Double-click a value to change it.
► Mark a favorite to use it as the default sweep profile for future
tests.
Note: The predefined profiles None, OMICRON expertise and
CPC template cannot be edited or deleted.
The default sweep profiles for this test are:
• Frequency sweep: OMICRON expertise
• Voltage sweep: none
Noise suppression settings
Averaging (no. points) Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
Device settings
Enable shield check ► Activate the check box if you want TESTRANO 600 to check whether
the shield of the high-voltage cable is connected.
Use beeper ► Activate the check box to activate the CP TD1 beeper during the
measurement.
208 OMICRON
PTM Bushing tests
Setting Description
Test conditions
Custom test conditions ► Activate the check box to set test conditions differing from the global
test conditions.
Top oil temperature ► Enter the temperature of the oil from the top of the transformer tank.
Ambient temperature ► Enter the ambient temperature on site.
Humidity ► Enter the relative ambient humidity on site.
Weather ► Select the weather conditions during the test.
Correction factors
Temperature correction ► Activate the check box to use temperature correction for this test.
Correction factor Temperature correction factor
Use reference voltage ► Activate the check box to extrapolate the I out and Watt losses
results for the specified reference voltage.
Reference voltage Reference voltage for extrapolation of the measurement results
The following table describes the Spare Bushing test measurement data.
Data Description
No. Number of the measurement
Measurement Arrangement of the measurement
Test mode Test mode according to the IEEE Std 62-1995
Sweep Swept variable: frequency, voltage, or none
V test Test voltage
Freq. Test frequency
V out Measured output voltage
I out Measured output current
Watt losses Measured losses
PF meas/ Measured power factor, dissipation factor, or tangent delta
DF meas/
Tanδ meas1
PF corr/ Corrected measured power factor, dissipation factor, or tangent delta
DF corr/
Tanδ corr1
Cap. meas Measured capacitance
Assessment Measurement assessment
1. Set by the regional conventions (see "Settings" on page 96).
OMICRON 209
TESTRANO 600 User Manual
Chapter Page
14.1 Oil Analysis 210
14.2 Insulation Resistance test 216
Setting Description
Asset
Asset Asset under test – set in the asset data
(see chapter 11 "PTM Asset data" on page 152)
Tank type Type of transformer tank
Insulation medium Insulation medium of the transformer – set in the asset data
(see chapter 11 "PTM Asset data" on page 152)
Note: The DGA is only valid for the insulation medium Mineral oil.
Oil type Type of transformer oil
Test conditions
Sample date Date of sample collection
Oil sample temperature Oil temperature at the time of sampling
210 OMICRON
Device-independent PTM tests
Setting Description
Measurement
Analyzed by Information on how the sample was analyzed
• Oil lab: The sample was analyzed by a laboratory.
After selecting Oil lab, you can enter the Name and Address of the
laboratory.
• Mobile DGA: The sample was analyzed using a mobile DGA device.
After selecting Mobile DGA, you can enter the device
Manufacturer/Type and its Serial number.
• Online DGA: The sample was analyzed using a permanently
installed monitoring device.
After selecting Online DGA, you can enter the device
Manufacturer/Type and its Serial number.
Use C3 hydrocarbons Activate the Use C3 hydrocarbons check box to add C3H6 and C3H8
to the list of Gas in oil values, and to activate ratio assessment
according to the MSS scheme.
Sampling point Sampling point on the transformer tank:
• Top
• Middle
• Bottom
Data Description
TDCG Total dissolved combustible gas
TDG Total dissolved gas
TCGe Estimation of the percentage of total combustible gas in the gas space.
It will only correspond to the actually measured value if there is a
balance between the gas blanket and the oil.
Lab. result Assessment result of the laboratory according to the IEEE or IEC
standard.
Assessment Manual Gas-in-oil analysis assessment:
• Manual pass
• Manual fail
• Manual investigate
• Not assessed
OMICRON 211
TESTRANO 600 User Manual
Assessment Summary
The results are assessed using the following interpretation methods:
• Duval’s triangles (see Table 14-3 below)
• IEC basic gas ratios
• Roger’s ratios
• Doernenburg’s ratios
• Key gases according to IEEE C57.104 and IEC 60599 (see Table 14-3 below)
• MSS scheme
212 OMICRON
Device-independent PTM tests
Condition 4
Condition 3
Condition 1
Indicator
Assumed fault –
see Assessment Summary
table
Duval’s triangle 1
Indicator
Indicator
OMICRON 213
TESTRANO 600 User Manual
Assessment Details
• The Table contains condition ranges and states for individual gases.
• The Ratio Table lists all used gas ratios, depending on the selected standard, and provides an
Interpretation of the recorded values.
Data Description
Table
Standard Standard used for the condition assessment
Overall assessment Condition fulfilled by the measured value of an individual gas
TDCG units/day Increase in TDCG per day since the last measurement
Recommendation Recommended interval for future measurements
Ratio Table
Sample Date Date of the sampling
Duval Triangle
Duval’s triangles visualize faults in a triangular coordinate system (see Table 14-3).
• Triangle 1: gases formed by faults of low to high energy
• Triangle 4: gases formed more specifically by faults of low energy or temperature
• Triangle 5: gases formed more specifically by faults of high temperature
Pattern
The key gas results are visually compared to four reference patterns. If a reference graph matches the
measured value, it is highlighted.
Data Description
Water content
H2O meas. Measured water content in oil
H2O @ 20 ºC Calculated water content in oil
Relative saturation Relative water saturation
Assessment Water content assessment
DC conductivity
Meas. value Measured DC conductivity
Test temperature Temperature of the oil during DC conductivity test
Field strength Field strength
Assessment DC conductivity assessment
214 OMICRON
Device-independent PTM tests
Data Description
Power factor
Standard Standard underlying the power factor analysis
Meas. value @ 25 ºC Power factor measured at 25 ºC
Meas. value @ 100 ºC Power factor measured at 100 ºC
Assessment Power factor assessment
Dielectric breakdown voltage
Standard Standard underlying the dielectric breakdown voltage analysis
Meas. value Measured dielectric breakdown voltage
Test temperature Oil temperature during dielectric breakdown voltage test
Assessment Dielectric breakdown voltage assessment
Chemical
Interfacial tension Interfacial tension of the oil
Neutralization value Neutralization value of the oil
Particle count Particle count of the oil
Color Color of the oil
Assessment Chemical assessment
Status Description
Prepared
Partially executed See Table 9-8: "Job statuses" on page 110.
Executed
Note: The test status set in the Oil Analysis test is displayed in the job overview (see 9.7.2 "Job
overview" on page 112) under Tests.
OMICRON 215
TESTRANO 600 User Manual
Setting Description
Test conditions
Test object temperature Temperature of the test object
Custom test conditions Activate the Custom test conditions check box to set test conditions
differing from the global test conditions.
Ambient temperature Ambient temperature on site
Humidity Relative ambient humidity
Calculations
PI calculation Calculation of polarization index
Time 1 In the standard PI calculation, the testing device is applied and insulation
resistance measurements are taken after 60 seconds (Time 1) and 600
Time 2
seconds (Time 2).
The polarization index (PI) is calculated as follows:
R 600
PI = -----------
R 60
Correction factors
Temperature correction Select the Temperature correction check box to activate temperature
correction.
Correction temp. Temperature correction factor
216 OMICRON
Device-independent PTM tests
Setting Description
Test data To import a file containing test data:
► Press Add to browse your PC and add data from a file.
To directly import data from a measurement file:
► Open the file on your computer.
► In the file press CTRL+A to mark all content, then press CTRL+C to
copy.
► In Primary Test Manager press Paste from clipboard.
The results may take a few seconds to load.
Measurement Name or number of the measurement
PI Polarization index
DAR Dielectric absorption ratio
Time Time at which the given values were recorded
Voltage
Voltage and current values recorded at the Time specified in the first
V DC
column
I DC
OMICRON 217
TESTRANO 600 User Manual
15 Technical data
At the time of factory adjustment all units are within the typical accuracy values specified in this
document.
Typical accuracy means that 98 % of all units meet the specified values at 23 °C ± 5 °C/73 ºF ± 10 ºF,
after a warm-up time of more than 25 min., and in a frequency range of 45 Hz to 65 Hz or DC.
The typical accuracy values multiplied by 3 are guaranteed at an ambient temperature of
23 ºC ± 5 ºC/73 ºF ± 10 ºF, after a warm-up time more than 25 min., and in a frequency range of
45 Hz to 65 Hz or DC.
Accuracy values indicate that the error is smaller than:
± (value read × reading error [rd] + full scale of range × range error [rg]).
For mains voltages below 190 V AC the system is subject to power restrictions.
OMICRON suggests that you send in your unit for calibration at least once a year.
Technical data are subject to change without notice.
CAT level
The CAT level required depends on the TESTRANO 600 application. All CAT ratings are defined for sea
levels below 2000 m. There are some limitations between 2000 m and 5000 m sea level (see
section 15.4 "Environmental conditions" on page 229).
CAT I is required when the measured voltage is generated by the test set itself. No voltages from other
sources are measured.
CAT II is required when measuring within electrical devices or between mains supply and devices.
CAT III is required when measuring in electrical installations such as control cubicles that are still
connected to the station battery or mains. The electrical installations are protected by a fuse.
218 OMICRON
Technical data
Characteristic Rating
Frequency DC or 15 Hz … 599 Hz
Vmains P30 s Pcontinuous
Power >100 VRMS 1500 W 1000 W
>190 VRMS 4000 W 2400 W
3 × 0 … ±56 VDC1
DC low range 33 ADC
1 × 0 … ±170 VDC2
AC high range
3 × 0 … 230 VRMS (LN)3 100 mARMS
low current
3 × 0 … 80 VRMS (LN)4
AC high range 16 ARMS
1 × 0 … 240 VRMS5
3 × 0 … 40 VRMS (LN)5
AC low range 33 ARMS
1 × 0 … 120 VRMS
1. See Figure 15-3: "Permitted operating range 3 x DC 113 V 16 A" on page 222
2. See Figure 15-1: "Permitted operating range 1 x DC 340 V 16 A" on page 221
3. See Figure 15-5: "Derating of output power and output voltage 3 x 230 VRMS" on page 223
4. See Figure 15-4: "Permitted operating range 3 x AC 80 V 16 A" on page 222
5. See Figure 15-2: "Permitted operating range 1 x AC 240 V 16 A" on page 221
Characteristic Accuracy1
Voltage accuracy DC 0.033 % rd ± 0.017 % range
Voltage accuracy AC (50 Hz) at burden open
0.33 % rd ± 0.17 % range
load
Phase accuracy AC (50 Hz) burden open load,
± 0.36°
V>20 VRMS
1. Typical accuracy at 23 °C ±5 K
OMICRON 219
TESTRANO 600 User Manual
1. See Figure 15-3: "Permitted operating range 3 x DC 113 V 16 A" on page 222
2. See Figure 15-1: "Permitted operating range 1 x DC 340 V 16 A" on page 221
3. See Figure 15-4: "Permitted operating range 3 x AC 80 V 16 A" on page 222
4. See Figure 15-2: "Permitted operating range 1 x AC 240 V 16 A" on page 221
Characteristic Accuracy1
Current accuracy DC 0.033 % rd ± 0.017 % range
Current accuracy AC
0.33 % rd ± 0.17 % range
50/60 Hz at burden 0.1 Ω
1. Typical accuracy at 23 °C ±5 K
220 OMICRON
Technical data
400
350
High range continuous
300 DC 340 V, 16 A
Output voltage [V]
250
200
100
50
0
0 5 10 15 20 25 30 35
Output current [A]
300
250
150
Low range continuous
AC 120 V, 33 A
100
50
0
0 5 10 15 20 25 30 35
OMICRON 221
TESTRANO 600 User Manual
120
100
High range continuous
DC 113 V, 16 A
80
Output voltage [V]
40
20
0
0 5 10 15 20 25 30 35
90
80
60
Output voltage [V]
50
30
20
10
0
0 5 10 15 20 25 30 35
Output current [A]
222 OMICRON
Technical data
260
24
240
22
220
20
200
18
180
160
14
140
12 120
10
100
8
80
6 60
4 40
2 20
0 0
0 5 10 15 20 25 30 35 40 45 50 55 60
Figure 15-5: Derating of output power and output voltage 3 x 230 VRMS
100
90
80
70
Output current [%]
60
50
40
30
20
10
0
-10 -5 0 5 10 15 20 25 30 35 40 45 50 55
OMICRON 223
TESTRANO 600 User Manual
224 OMICRON
Technical data
Characteristic Rating
Voltage 300 VRMS
-2
-4
-6
Amplitude (dB)
-8
-10
-12
-14
-16
-18
49 49.2 49.4 49.6 49.8 50 50.2 50.4 50.6 50.8 51
Frequency (Hz)
OMICRON 225
TESTRANO 600 User Manual
15.1.3 Interfaces
Table 15-11: Connector overview
Interface Rating
1 × EtherCAT®1
1 × Ethernet
Digital
1 × Serial
2 × Safety
6 × Configurable outputs:
– (HV) 3 × analog output
– (LV) 3 × analog output
6 × Configurable inputs:
– (HV) 3 × analog input
Analog – (LV) 3 × analog input
On-load tap changer interface:
– 2 × internal switch
– 1 × voltage measurement
– 1 × current clamp measurement
1 × Booster interface
1. EtherCAT® is registered trademark and patented technology, licensed by Beckhoff automation GmbH, Germany.
SAFETY connectors
Table 15-12: SAFETY 1 and SAFETY 2 pin assignment
6 8
7 Ground Ground
7 9 8 Start button IN (n/c) Start button OUT (n/c)
9 Ground Ground
226 OMICRON
Technical data
Display
Table 15-13: Display
Characteristic Rating
10.6 in
Size
26.9 cm
Resolution 1280 x 768 WXGA
Type Color touch TFT LCD
Contrast ratio 1000:1
Luminance 800 cd/m2
Viewing angle (CR ≥ 10) 85° (H), 85° (V)
OMICRON 227
TESTRANO 600 User Manual
Range name
Voltage at HV Range1 Accuracy2
(LV voltage range)
1 0.03 % rd +
300 VRMS ------------------
1 …10 0.043 % range
1 0.027 % rd +
30 VRMS -------------------------
10 …100 0.043 % range
230 VRMS HV (LN)
1 0.027 % rd +
3 VRMS -------------------------------
100 …1000 0.043 % range
1 0.027 % rd +
300 mVRMS --------------------------------------
1000 …10000 0.043 % range
LV
1. Range = -------
-
HV
2. Typical accuracy at 23 °C ±5 K
228 OMICRON
Technical data
Characteristic Rating
Nominal 100 V … 240 VAC
Voltage
Permitted 85 V … 264 VAC
Current Nominal 16 A
Nominal 50 Hz/60 Hz
Frequency
Permitted 45 Hz … 65 Hz
Automatic circuit breaker with magnetic
Power fuse
overcurrent tripping at I >16 A
Continuous <3.6 kW
Power consumption
Peak <5.0 kW
Current consumption, continuous <16 AAC
Connector type IEC320/C20, 1 phase
Characteristic Rating
Operating -10 ºC … +55 ºC/+14 ºF…+131 ºF
Temperature
Storage -30 ºC … +70 ºC/-22 ºF…+158 ºF
2000 m/6550 ft, up to 5000 m/16400 ft with
Operating
Max. altitude limited specifications1
Storage 12 000 m/40 000 ft
1. Output TAP CHANGER (CAT III / 300 V): from 2000 m/6550 ft to 5000 m/16400 ft altitude only CAT II compliance or CAT III
compliance with half voltage
Characteristic Rating
464 × 386 × 229 mm
With cover, without handles
Dimensions 18.3 × 15.2 × 9 in
(w × h× d) 580 × 386 × 229 mm
With cover, with handles
22.8 × 15.2 × 9 in
Device with display 20.6 kg/45.5 lb
Weight
Device without display 19.5 kg/43 lb
OMICRON 229
TESTRANO 600 User Manual
15.6 Standards
Table 15-20: Standards conformity
EMC, safety
EMC IEC/EN 61326-1
(industrial electromagnetic environment)
FCC subpart B of part 15, class A
Safety IEC/EN/UL 61010-1,
IEC/EN/UL 61010-2-30
Other
IEC/EN 60068-2-27
Shock
(15 g/11 ms, half-sinusoid, 3 shocks in each axis)
IEC/EN 60068-2-6
Vibration (frequency range 10 Hz…150 Hz, acceleration 2 g continuous
(20 m/s2/65 ft/s2), 20 cycles per axis)
IEC/EN 60068-2-78
Humidity (5 % … 95 % relative humidity, no condensation),
tested at 40 ºC/104 ºF for 48 hours
230 OMICRON
Support
Support
When you are working with our products we want to provide you with the greatest
possible benefits. If you need any support, we are here to assist you!
OMICRON electronics GmbH, Oberes Ried 1, 6833 Klaus, Austria, +43 59495
OMICRON 231
ENU 1161 05 04