Metode DAN Rancob Diktat
Metode DAN Rancob Diktat
Introduction
Design of Experiments DOEs refers to a structured, planned method, which is used to find the
relationship between different factors let ′ ssay, Xvariables that affect a project and the different
outcomes of a project let ′ ssay, Yvariables.
The method was coined by Sir Ronald A. Fisher in the 1920s and 1930s.
Ten to twenty experiments are designed where the applicable factors varied methodically. The
results of the experiments are then analyzed to classify optimal conditions to find the factors that
have the most influence on the results as well as those that do not and to identify interfaces and
synergies among the factors.
DOEs are mainly used in the research and development department of an organization where
majority of resources goes towards optimization problems.
In order to minimize optimization problems, it is important to keep costs low by conducting few
experiments. Design of Experiments is useful in this case, as it only necessitates a small number of
experiments, thereby helping to reduce costs.
Once the following eight steps are sequentially followed, you will be able to receive a successful
outcome from Design of Experiments.
Step 1
Set Good Objectives: Before one begins to design an experiment, it is important to set out its
objective. With a defined objective, it is easy to screen out factors not relevant to the experiment.
This way one optimizes the key critical factors.
However, when one sets a set of good objectives, many irrelevant factors are eliminated. With
well-defined objectives, managers can use a response surface design of experiment which
explores few factors, albeit at many levels.
Also drawing up good objectives at the beginning helps build a solid understanding of the project
as well as create realistic expectations of it's outcome.
Step 2
Measure Responses Quantitatively: Many Designs of Experiments end in failure because their
responses cannot be measured quantitatively.
For example, product inspectors use a qualitative method of determining if a product passes
quality assurance or not. This is not efficient in designs of experiments as a pass/fail is not
accurate enough.
Step 3
Replicate to Dampen Uncontrollable Variation: Replicating a given set of conditions many times
gives more opportunities for one to precisely estimate responses.
Replicating also gives one the opportunity to detect significant effects such as signals amid the
natural process uncontrollable variations, like noise.
For some projects, variations such as noise drown out the signal, so it is useful to find the signal to
noise ratio before doing a design of experiment.
Step 4
Randomize the Run Order: In order to evade uncontrollable influences such as changes in raw
material and tool wear, it is necessary to run experiments in a randomized order.
These variable influences can have a significant effect on the selected variable. If an experiment is
not run in a random order, the design of experiment will specify factor effects that are in fact from
these variable influences.
Step 5
Block out Known Sources of Variation: Through blocking, one can screen out the effects of known
variables such as shift changes or machine differences.
One can divide the experimental runs into homogenous blocks and then mathematically remove
the differences. This increases the sensitivity of the design of experiment. However, it is important
to not block out anything one wants to study.
Step 6
Know Which Effects ifany Will be Aliased: An alias means that one has changed one or more
things in the same way at the same time.
Step 7
Do a Sequential Series of Experiments: When conducting a design of experiment it is
important to conduct it in a chronological manner, that is, information gleaned in one experiment
should be able to be applied to the next.
Step 8
Always Confirm Critical Findings: At the end of a design of experiment, it is easy to assume
that the results are accurate.
However, it is important to confirm one's findings and to verify the results. This validation can be
done using many other management tools available.
Conclusion
Design of Experiments is an important tool that can be utilized in most manufacturing industries.
Managers, who use the method, will not only save on costs but also make improvements in the
quality of their product as well as ensure process efficiency.
Once Design of Experiments is completed, the managers should make an extra effort to validate
the outcome and carry out further analysis of the findings.
Loading [MathJax]/jax/output/HTML-CSS/jax.js