Aula14 Sistemas Seguranca 2sem2014
Aula14 Sistemas Seguranca 2sem2014
EIO0000001584 06/2016
Modicon M580
RIO Modules
Installation and Configuration Guide
06/2016
EIO0000001584.05
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical
characteristics of the performance of the products contained herein. This documentation is not
intended as a substitute for and is not to be used for determining suitability or reliability of these
products for specific user applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products with respect to the
relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or
subsidiaries shall be responsible or liable for misuse of the information contained herein. If you
have any suggestions for improvements or amendments or have found errors in this publication,
please notify us.
No part of this document may be reproduced in any form or by any means, electronic or
mechanical, including photocopying, without express written permission of Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when installing and
using this product. For reasons of safety and to help ensure compliance with documented system
data, only the manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant
instructions must be followed.
Failure to use Schneider Electric software or approved software with our hardware products may
result in injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2016 Schneider Electric. All Rights Reserved.
2 EIO0000001584 06/2016
Table of Contents
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 1 Characteristics of Ethernet RIO Modules . . . . . . . . . . . . 15
Adapter Module Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LED Indicators on Adapter Modules . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adapter Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
RIO Network Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Modicon X80 I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Configuring the BMXNOM0200.4 Module in an X80 Drop . . . . . . . . . 35
Hardened (H) Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Standards, Certifications and Operational Recommendations . . . . . . 39
Chapter 2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.1 Installing Modicon X80 Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Maximum Configuration in RIO Drops. . . . . . . . . . . . . . . . . . . . . . . . . 43
Modicon X80 Backplane Considerations. . . . . . . . . . . . . . . . . . . . . . . 44
Adapter and I/O Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Setting the Location of the Ethernet Remote I/O Drop . . . . . . . . . . . . 50
2.2 Remote I/O Infrastructure Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Duplicate IP Address Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Loss of I/O Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Chapter 3 Configuration and Programming with Unity Pro . . . . . . . 57
3.1 Creating a Unity Pro Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Configuring the RIO Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.2 Unity Pro Configuration for Ethernet RIO Modules . . . . . . . . . . . . . . . 61
RSTP Bridge Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
SNMP Agent Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Service Port Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
3.3 Unity Pro Configuration for RIO Drops . . . . . . . . . . . . . . . . . . . . . . . . 66
Configuring Remote Drop Parameters . . . . . . . . . . . . . . . . . . . . . . . . 67
Time Stamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Device DDT Names for M580 RIO Adapters . . . . . . . . . . . . . . . . . . . . 72
Chapter 4 Implicit and Explicit Messaging. . . . . . . . . . . . . . . . . . . . 79
Explicit Messaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Implicit I/O Exchanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
EIO0000001584 06/2016 3
Chapter 5 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.1 Service Port Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Service Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
5.2 Diagnostics Available through the CPU . . . . . . . . . . . . . . . . . . . . . . . . 85
System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.3 Diagnostics Available through Modbus/TCP . . . . . . . . . . . . . . . . . . . . 87
Modbus Diagnostic Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.4 Diagnostics Available through EtherNet/IP CIP Objects . . . . . . . . . . . 88
About CIP Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Identity Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Assembly Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Connection Manager Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Quality of Service (QoS) Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
TCP/IP Interface Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Ethernet Link Object. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
EtherNet/IP Interface Diagnostics Object. . . . . . . . . . . . . . . . . . . . . . . 104
I/O Connection Diagnostics Object . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
EtherNet/IP Explicit Connection Diagnostics Object . . . . . . . . . . . . . . 111
EtherNet/IP Explicit Connection Diagnostics List Object . . . . . . . . . . . 113
RSTP Diagnostics Object. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Service Port Control Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
SNTP Diagnostics Object. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Ethernet Backplane Diagnostics Object. . . . . . . . . . . . . . . . . . . . . . . . 126
5.5 Diagnostics Available through Unity Pro . . . . . . . . . . . . . . . . . . . . . . . 129
Introduction to Unity Pro Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Displaying I/O Memory Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . 131
Chapter 6 Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Adapter Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
4 EIO0000001584 06/2016
Safety Information
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with the device
before trying to install, operate, service, or maintain it. The following special messages may appear
throughout this documentation or on the equipment to warn of potential hazards or to call attention
to information that clarifies or simplifies a procedure.
EIO0000001584 06/2016 5
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified
personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of
the use of this material.
A qualified person is one who has skills and knowledge related to the construction and operation
of electrical equipment and its installation, and has received safety training to recognize and avoid
the hazards involved.
WARNING
UNGUARDED EQUIPMENT
Do not use this software and related automation equipment on equipment which does not have
point-of-operation protection.
Do not reach into machinery during operation.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
This automation equipment and related software is used to control a variety of industrial processes.
The type or model of automation equipment suitable for each application will vary depending on
factors such as the control function required, degree of protection required, production methods,
unusual conditions, government regulations, etc. In some applications, more than one processor
may be required, as when backup redundancy is needed.
Only you, the user, machine builder or system integrator can be aware of all the conditions and
factors present during setup, operation, and maintenance of the machine and, therefore, can
determine the automation equipment and the related safeties and interlocks which can be properly
used. When selecting automation and control equipment and related software for a particular
application, you should refer to the applicable local and national standards and regulations. The
National Safety Council's Accident Prevention Manual (nationally recognized in the United States
of America) also provides much useful information.
In some applications, such as packaging machinery, additional operator protection such as point-
of-operation guarding must be provided. This is necessary if the operator's hands and other parts
of the body are free to enter the pinch points or other hazardous areas and serious injury can occur.
Software products alone cannot protect an operator from injury. For this reason the software
cannot be substituted for or take the place of point-of-operation protection.
Ensure that appropriate safeties and mechanical/electrical interlocks related to point-of-operation
protection have been installed and are operational before placing the equipment into service. All
interlocks and safeties related to point-of-operation protection must be coordinated with the related
automation equipment and software programming.
6 EIO0000001584 06/2016
NOTE: Coordination of safeties and mechanical/electrical interlocks for point-of-operation
protection is outside the scope of the Function Block Library, System User Guide, or other
implementation referenced in this documentation.
WARNING
EQUIPMENT OPERATION HAZARD
Verify that all installation and set up procedures have been completed.
Before operational tests are performed, remove all blocks or other temporary holding means
used for shipment from all component devices.
Remove tools, meters, and debris from equipment.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Follow all start-up tests recommended in the equipment documentation. Store all equipment
documentation for future references.
Software testing must be done in both simulated and real environments.
Verify that the completed system is free from all short circuits and temporary grounds that are not
installed according to local regulations (according to the National Electrical Code in the U.S.A, for
instance). If high-potential voltage testing is necessary, follow recommendations in equipment
documentation to prevent accidental equipment damage.
Before energizing equipment:
Remove tools, meters, and debris from equipment.
Close the equipment enclosure door.
Remove all temporary grounds from incoming power lines.
Perform all start-up tests recommended by the manufacturer.
EIO0000001584 06/2016 7
OPERATION AND ADJUSTMENTS
The following precautions are from the NEMA Standards Publication ICS 7.1-1995 (English
version prevails):
Regardless of the care exercised in the design and manufacture of equipment or in the selection
and ratings of components, there are hazards that can be encountered if such equipment is
improperly operated.
It is sometimes possible to misadjust the equipment and thus produce unsatisfactory or unsafe
operation. Always use the manufacturer’s instructions as a guide for functional adjustments.
Personnel who have access to these adjustments should be familiar with the equipment
manufacturer’s instructions and the machinery used with the electrical equipment.
Only those operational adjustments actually required by the operator should be accessible to
the operator. Access to other controls should be restricted to prevent unauthorized changes in
operating characteristics.
8 EIO0000001584 06/2016
About the Book
At a Glance
Document Scope
This document describes the adapter modules that can be used in X80 RIO drops.
This guide describes these adapter modules:
BMECRA31210
BMXCRA31210
BMXCRA31200
NOTE: This book discusses BM•CRA312•1 adapter modules in M580 systems. To use Quantum
140CRA312•0 adapter modules in an M580 system, refer to the Quantum RIO Modules guide
(see Quantum EIO, Remote I/O Modules, Installation and Configuration Guide).
These CPUs support Quantum RIO drops that include a 140CRA312•0 adapter module:
BMEP584040 (version 2.10 or later)
BMEP585040
BMEP586040
BMEH584040
BMEH586040
NOTE: The specific configuration settings contained in this guide are for instructional purposes
only. The settings required for your specific application can be different from the examples
presented in this guide. To configure RIO drops in an M580 Hot Standby system, refer to the
Modicon M580 Hot Standby Installation and Configuration Guide (see Modicon M580 Hot
Standby, System Planning Guide for, Frequently Used Architectures).
NOTE: The architectures described in this document have been tested and validated in various
scenarios. If you intend to use architectures different than the ones described in this document,
test and validate them thoroughly before implementing.
Validity Note
This document is valid for X80 RIO systems when used with Unity Pro 11.1 or later.
The technical characteristics of the devices described in this document also appear online. To
access this information online:
Step Action
1 Go to the Schneider Electric home page www.schneider-electric.com.
2 In the Search box type the reference of a product or the name of a product range.
Do not include blank spaces in the reference or product range.
To get information on grouping similar modules, use asterisks (*).
EIO0000001584 06/2016 9
Step Action
3 If you entered a reference, go to the Product Datasheets search results and click on the
reference that interests you.
If you entered the name of a product range, go to the Product Ranges search results and click
on the product range that interests you.
4 If more than one reference appears in the Products search results, click on the reference that
interests you.
5 Depending on the size of your screen, you may need to scroll down to see the data sheet.
6 To save or print a data sheet as a .pdf file, click Download XXX product datasheet.
The characteristics that are presented in this manual should be the same as those characteristics
that appear online. In line with our policy of constant improvement, we may revise content over time
to improve clarity and accuracy. If you see a difference between the manual and online information,
use the online information as your reference.
Related Documents
10 EIO0000001584 06/2016
Title of Documentation Reference Number
Modicon M580 BMENOS0300 Network Option Switch Module NHA89117 (English),
Installation and Configuration Guide NHA89119 (French),
NHA89120 (German),
NHA89121 (Italian),
NHA89122 (Spanish),
NHA89123 (Chinese)
Modicon M580 BMENOC03•1 Ethernet Communication Module HRB62665 (English),
Installation and Configuration Guide HRB65311 (French),
HRB65313 (German),
HRB65314 (Italian),
HRB65315 (Spanish),
HRB65316 (Chinese)
Modicon M580 Change Configuration on the Fly User Guide EIO0000001590 (English),
EIO0000001591 (French),
EIO0000001592 (German),
EIO0000001594 (Italian),
EIO0000001593 (Spanish),
EIO0000001590 (Chinese)
Modicon M340/X80 BMX NRP 020• Fiber Optic Repeater Module EIO0000001108 (English),
User Guide EIO0000001109 (French),
EIO0000001110 (German),
EIO0000001111 (Spanish),
EIO0000001112 (Italian),
EIO0000001113 (Chinese)
Modicon M340/X80 with Unity Pro Analog Input/Output Modules 35011978 (English),
User Manual 35011979 (German),
35011980 (French),
35011981 (Spanish),
35011982 (Italian),
35011983 (Chinese)
Modicon M340/X80 with Unity Pro Discrete Input/Output Modules 35012474 (English),
User Manual 35012475 (German),
35012476 (French),
35012477 (Spanish),
35012478 (Italian),
35012479 (Chinese)
Modicon M340/X80 with Unity Pro BMX EHC 0200 Counting Module 35013355 (English),
User Guide 35013356 (German),
35013357 (French),
35013358 (Spanish),
35013359 (Italian),
35013360 (Chinese)
EIO0000001584 06/2016 11
Title of Documentation Reference Number
BMX ERT 1604 T Modicon M340 ERT Module User Manual EIO0000001121 (English),
EIO0000001122 (French),
EIO0000001123 (German),
EIO0000001124 (Spanish),
EIO0000001125 (Italian),
EIO0000001126 (Chinese)
System Time Stamping User Guide EIO0000001217 (English),
EIO0000001707 (French),
EIO0000001708 (German),
EIO0000001709 (Spanish),
EIO0000001710 (Italian),
EIO0000001711 (Chinese)
Applicative Time Stamping with Unity Pro User Guide EIO0000001268 (English),
EIO0000001702 (French),
EIO0000001703 (German),
EIO0000001704 (Spanish),
EIO0000001705 (Italian),
EIO0000001706 (Chinese)
Unity Pro Program Languages and Structure Reference Manual 35006144 (English),
35006145 (French),
35006146 (German),
35006147 (Spanish),
35013361 (Italian),
35013362 (Chinese)
Unity Pro Operating Modes 33003101 (English),
33003102 (French),
33003103 (German),
33003104 (Spanish),
33003696 (Italian),
33003697 (Chinese)
Unity Pro Installation Manual 35014792 (French),
35014793 (English),
35014794 (German),
35014795 (Spanish),
35014796 (Italian),
35012191 (Chinese)
Unity Pro Installation Manual Modicon X80 with Unity Pro HART EAV16400 (English),
Analog Input/Output Modules User Guide EAV28404 (French),
EAV28384 (German),
EAV28360 (Spanish),
EAV28413 (Italian),
EAV28417 (Chinese)
12 EIO0000001584 06/2016
You can download these technical publications and other technical information from our website
at http://download.schneider-electric.com
EIO0000001584 06/2016 13
14 EIO0000001584 06/2016
Modicon M580
Characteristics of Ethernet RIO Modules
EIO0000001584 06/2016
Chapter 1
Characteristics of Ethernet RIO Modules
Introduction
This chapter describes the adapter modules that can be used in the remote drops of an X80
system. Specifically, these modules are:
BMECRA31210
BMXCRA31210
BMXCRA31200
This chapter includes physical characteristics, port descriptions, and agency specifications for
these modules.
NOTE: This book describes the BM• CRA 312 •1 adapter modules. To use Quantum 140 CRA
adapter modules in M580 systems, refer to the Quantum RIO Modules guide (see Quantum EIO,
Remote I/O Modules, Installation and Configuration Guide).
EIO0000001584 06/2016 15
Characteristics of Ethernet RIO Modules
Introduction
An RIO drop consists of one or two racks of Modicon X80 I/O modules and/or third-party
PME SWT 0100 modules. An RIO drop is connected to the daisy-chain loop on which the Ethernet
RIO network resides. Each remote drop contains one BM•CRA312•0 adapter module. Each rack
in a remote drop contains its own power supply module.
Remote adapter modules are available as Ethernet BME and X Bus BMX communicators. To use
X80 I/O modules that require Ethernet, choose a BME-style adapter module. If your X80 I/O uses
only X Bus for backplane communication, then you can use a BMX-style adapter module.
The adapter modules are:
Adapter Description
X80 standard EIO The BMXCRA31200 is a basic adapter module that supports X Bus communications
adapter across the remote backplane, but not Ethernet.
It does not support:
more than 9 I/O modules
an extension rack
special-purpose or Ethernet I/O modules
native timestamping
service port
I/O to be solved more than once per logic scan in the remote drop. (It only handles
MAST (see page 81) tasks. Your application cannot assign FAST and AUX tasks in
it.
X80 performance The BMXCRA31210 adapter module supports X Bus communications across the
EIO adapter remote backplane, but not Ethernet.
It supports:
up to 17 I/O modules
an extension rack
special-purpose modules
native timestamping
service port
MAST (see page 81), FAST (see page 81), and AUX0 (see page 82)/AUX1
(see page 82) task customization of the Ethernet I/O scanner service
eX80 performance The BMECRA31210 adapter supports Ethernet and X Bus communications across the
EIO adapter remote backplane. This adapter needs to be installed in an Ethernet backplane.
It supports:
the capabilities of a BMXCRA31210 adapter
Ethernet I/O modules on rack slots connected to the Ethernet backplane in the
remote drop, such as the BMEAHI0812 and BMEAHO0412 HART-compatible
analog modules, and PME SWT 0100 weighing module
16 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
NOTE: You can also use these BMECRA312•0 eX80 EIO adapter modules in a Quantum EIO
system with a high-end CPU (140CPU6•••• (see Quantum with Unity Pro, Hardware, Reference
Manual)) configured on the local rack.
Functionality
The adapters exchange data through the Ethernet I/O scanner service in the CPU on the main local
rack of your PAC system:
The input data from the RIO drop is collected and published to the I/O scanner.
The output modules are updated with the data received from the I/O scanner.
The protocol used for exchange is EtherNet/IP.
The exchanges are deterministic, which means that the RIO logic is scanned regularly in a
scheduled and predictable manner.
NOTE: Refer to your system hardware reference manual to select a CPU that supports the
Ethernet I/O scanner service.
External Features
These adapter modules have the same dimensions and installation constraints as the other
modules in the Modicon X80 product line:
1 LED display
2 rotary switches
3 SERVICE port (ETH 1)
4 DEVICE NETWORK port (ETH 2)
5 DEVICE NETWORK port (ETH 3)
EIO0000001584 06/2016 17
Characteristics of Ethernet RIO Modules
18 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
Display
The LEDs are on the front of the adapter module:
Indications
NOTICE
UNINTENTIONAL EQUIPMENT BEHAVIOR
Confirm that each module has a unique IP address. Duplicate IP addresses can cause
unpredictable module/network behavior.
Failure to follow these instructions can result in equipment damage.
LED conditions:
EIO0000001584 06/2016 19
Characteristics of Ethernet RIO Modules
20 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
Port Description
SERVICE The SERVICE port allows the diagnosis of Ethernet device network ports and provides access
to external tools and devices (Unity Pro, ConneXium Network Manager, HMI, and so forth).
The port supports these modes:
access port (default): This mode supports Ethernet communications.
port mirroring: In this mode, data traffic from one of the other 2 ports is copied to this port.
This allows a connected management tool to monitor and analyze the port traffic.
disabled
NOTE:
The BMXCRA31200 does not have a SERVICE port.
You can configure the SERVICE port either ONLINE or OFFLINE.
In port mirroring mode, the SERVICE port acts like a read-only port. That is, you cannot
access devices (ping, connection to Unity Pro, and so forth) through the SERVICE port.
Refer to Service Port Configuration (see page 65).
DEVICE The DEVICE NETWORK copper ports are used to put the drop on the simple daisy chain loop.
NETWORK They provide:
connections for RIO communications
cable redundancy
CAUTION
ETHERNET CONNECTION NON-OPERATIONAL
Do not connect a device with a speed in excess of 100 Mbit/s to any adapter port.
Failure to follow these instructions can result in injury or equipment damage.
Connecting a device with a speed in excess of 100 Mbit/s , the Ethernet link may not be established
between the device and the module through its port.
EIO0000001584 06/2016 21
Characteristics of Ethernet RIO Modules
22 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
Introduction
Use a daisy chain loop network configuration that implements the RSTP service to establish
redundant communications with at least one of the two physical paths between:
the I/O scanner
the adapter modules at each remote drop, dual ring switches (DRSs), or any product that has
the capacity to be RIO scanned
For network topology planning, refer to your system planning guide.
NOTE: Fiber optic ports are not available on the adapter modules. For fiber optic support use either
a BMXNRP020• optic fiber conversion module or a pair of DRSs.
1 main local rack with a BME•58••40 CPU with the Ethernet I/O scanner service
2 X80 RIO drops with a BM•CRA312•0 adapter module
3 the daisy chain loop
EIO0000001584 06/2016 23
Characteristics of Ethernet RIO Modules
Introduction
The following I/O modules can be mounted in local racks or RIO drops in an M580 system.
Some of these modules also contain embedded web pages that can be used for configuration and
diagnostics. Web page descriptions are provided in the appropriate product documentation and in
Unity Pro help.
NOTE: Conformally coated (hardened H) versions of many of these modules are also available.
These I/O modules are supported in Modicon X80 local racks containing a CPU and RIO drops:
24 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
EIO0000001584 06/2016 25
Characteristics of Ethernet RIO Modules
26 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
NOTE: Schneider Electric recommends that you use Unity Loader to upgrade the modules with the
latest available version. (It is not necessary to update a BMXART0414 module, V2.1 or later,
because it works correctly with a BM•CRA312•0 X80 EIO adapter module.)
EIO0000001584 06/2016 27
Characteristics of Ethernet RIO Modules
28 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
EIO0000001584 06/2016 29
Characteristics of Ethernet RIO Modules
30 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
EIO0000001584 06/2016 31
Characteristics of Ethernet RIO Modules
32 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
Hardened Modules
These hardened modules are supported in M580 local racks (containing a CPU) and RIO drops
that contain a BM•CRA312•0 EIO adapter module. For details regarding hardened modules, refer
to the manuals for these modules.
EIO0000001584 06/2016 33
Characteristics of Ethernet RIO Modules
34 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
Introduction
In X80 EIO drops, Modbus slave messages received by the BMXNOM0200.4 module are
transferred to the X80 EIO adapter module (BMXCRA31210.3). The adapter module forwards the
message to the CPU.
To configure the BMXNOM0200 as a Modbus RS-485 RTU slave in an X80 drop, use these
firmware versions:
BMXCRA31210.3 SV ≥ V2.12
BMXNOM0200.4 SV ≥ V1.5
The BMXNOM0200.4 module is configured differently in an M580 X80 drop than Quantum RIO
drop, and is compatible with M580 BME•58••40 CPUs.
Step Action
1 Install the CPU module on the local rack.
2 Install the BMXCRA31210.3 module on an X80 drop.
3 Install the BMXNOM0200.4 module in the X80 drop.
Supported Protocols
For the BMXNOM0200.4 module:
Channel 0 supports RS-232 or RS-485.
Channel 1 supports only RS-485.
Declaring the BMXNOM0200 module as a BMXNOM0200.4 module in Unity Pro allows you to
configure the module for:
Modbus RTU slave on RS-485
NOTE:
Only Modbus RTU is supported as slave protocol.
Only RS-485 is supported when Modbus slave is selected.
Modbus Serial RTU and ASCII Master on RS-232 and RS-485
Character mode
EIO0000001584 06/2016 35
Characteristics of Ethernet RIO Modules
Hot Standby
The CPU Main IP address swaps in the case of a PAC switchover. The Modbus requests are still
forwarded to the primary CPU.
NOTE: The Modbus client application manages the repetition of requests in case of a message
loss that could occur during a PAC switchover.
Maximum Configuration
The maximum configuration of the BMXNOM0200.4 module includes the following elements:
36 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
Step Action
1 In the Unity Pro Project Browser, open the BMXNOM0200.4 module.
2 Select the channel to configure. By default:
Channel 0 is configured with the Character mode link function.
Channel 1 is configured with the Modbus link function.
NOTE: Some parameters are not accessible and are grayed out.
NOTE: Refer to the Modicon M340 with Unity Pro Serial Link User Manual for details on these
communication protocols: Modbus serial and character mode (see Modicon M340 with Unity Pro,
Serial Link, User Manual).
EIO0000001584 06/2016 37
Characteristics of Ethernet RIO Modules
M580H
The hardened (H) equipment is a ruggedized version of the equipment in your system. It can be
used at extended temperatures (-25...70ºC) (-13...158ºF) and in harsh chemical environments.
This equipment is ATEX certified.
This treatment increases the isolation capability of the circuit boards and their resistance to:
condensation
dusty atmospheres (conducting foreign particles)
chemical corrosion, in particular during use in sulphurous atmospheres (oil, refinery, purification
plant and so on) or atmospheres containing halogens (chlorine and so on)
The hardened equipment, when within the standard temperature range (0...60ºC) (32...140ºF), has
the same performance characteristics as the standard equipment.
If this equipment is operated outside the -25...70ºC (-13...158ºF) temperature range, the
equipment can operate abnormally.
WARNING
UNINTENDED EQUIPMENT OPERATION
Do not operate hardened equipment outside of its specified temperature range.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Hardened equipment has a conformal coating applied to its electronic boards. This protection,
when associated with appropriate installation and maintenance, allows it to be more robust when
operating in harsh chemical environments.
38 EIO0000001584 06/2016
Characteristics of Ethernet RIO Modules
EIO0000001584 06/2016 39
Characteristics of Ethernet RIO Modules
40 EIO0000001584 06/2016
Modicon M580
Installation
EIO0000001584 06/2016
Chapter 2
Installation
Installation
Overview
This chapter describes the hardware installation of an Modicon X80 remote I/O drop.
EIO0000001584 06/2016 41
Installation
Section 2.1
Installing Modicon X80 Modules
At a Glance
This section describes the installation of an Modicon X80 I/O adapter module.
42 EIO0000001584 06/2016
Installation
Maximum Configuration
The maximum number of I/O modules in an Modicon X80 RIO drop (with both a main remote rack
and an extension remote rack) using a BM•CRA312•0 adapter depends on the CPU used in the
main local rack.
Refer to your system hardware reference manual to select a CPU that supports the number and
types of I/O modules you need.
This table shows the maximum number of modules in an RIO drop with a remote extension rack:
NOTE: Refer to the M580 Hot Standby guide for instructions to configure RIO drops in Hot Standby
systems (see Modicon M580 Hot Standby, System Planning Guide for, Frequently Used
Architectures).
EIO0000001584 06/2016 43
Installation
Introduction
An X80 RIO drop can have one or two racks:
1. main RIO rack: BMEXBP••00 or BMXXBP••0
This rack is required in a drop and contains a BMXCRA31200, BMECRA31210, or
BMXCRA31210 EIO adapter module, a power supply, and, optionally, I/O modules.
2. extended RIO rack: only BMXXBP••0
This rack is optional in a drop and contains only I/O modules.
Confirm that extended remote racks are PV 02 or later. Install modules that require Ethernet
across the backplane on the main remote rack.
NOTE: The BMXCRA31200 does not support an extended RIO rack.
NOTE: The mounting screws on the left side of the backplane may be accessible without
unplugging the power supply module. Mount the backplane using the far left fastening hole on the
panel.
Compatible Racks
Use these racks in an Modicon X80 RIO drops:
X BUS (PV 02 or later) backplanes:
BMXXBP0400
BMXXBP0600
BMXXBP0800
BMXXBP1200
BMXXBP0400H
BMXXBP0600H
BMXXBP0800H
BMXXBP1200H
Ethernet backplanes:
BMEXBP0400
BMEXBP0602
BMEXBP0800
BMEXBP1002(2)
BMEXBP1200(1)
BMEXBP0400H
BMEXBP0602H
BMEXBP0800H
BMEXBP1002(2)
BMEXBP1200H(1)
1. The 12-slot Ethernet rack has eight Ethernet-X Bus slots and four X Bus-only slots.
2. The 10-slot Ethernet rack has eight Ethernet-X Bus slots and two X Bus-only slots.
44 EIO0000001584 06/2016
Installation
An Modicon X80 RIO drop can include two racks. In a 2-rack drop, the racks are linked with two
bus extender modules and a cable:
Grounding Considerations
DANGER
ELECTRICAL SHOCK HAZARD
Switch off the power supply at both ends of the PAC connection, and lock out and tag out both
the power sources.
In case lock out and tag out are not available, ensure that the power sources cannot be
inadvertently switched on.
Use suitable insulation equipment when inserting or removing all or part of this equipment.
Failure to follow these instructions will result in death or serious injury.
Do not apply power to an Modicon X80 rack until connections are made at both ends of the
Ethernet cable. For example, connect the cable to both the BMECRA31210 performance EIO
adapter module and another device (adapter module) or DRS before you turn on the power.
Refer to your system hardware reference manual for details about DRSs.
Use fiber-optic cable to establish a communications link when it is not possible to master the
potential between the two grounds.
EIO0000001584 06/2016 45
Installation
Introduction
Observe the following guidelines when you install these adapter modules in an Modicon X80 RIO
drop):
BMECRA31210
BMXCRA31210
BMXCRA31200
Grounding Considerations
DANGER
ELECTRICAL SHOCK HAZARD
Switch off the power supply at both ends of the PAC connection, and lock out and tag out both
the power sources.
In case lock out and tag out are not available, ensure that the power sources cannot be
inadvertently switched on.
Use suitable insulation equipment when inserting or removing all or part of this equipment.
Failure to follow these instructions will result in death or serious injury.
Use fiber optic cable to establish a communications link when it is not possible to equalize the
potentials between two grounds.
NOTE: Refer to the ground connection information in the Grounding and Electromagnetic
Compatibility of PLC Systems User Manual.
46 EIO0000001584 06/2016
Installation
redundant BMXCPS4002
EIO0000001584 06/2016 47
Installation
Mounting a Module
Step Action
1 Hold the module at an angle and mount it on the 2 hooks near the bottom of the backplane. The
figure shows the correct way to hold the module:
2 Swing the module up so that the connector engages the backplane connector.
3 Use a phillips-head screw driver to tighten the screw at the top of the module 2...4 in-lbs (0.22 to
0.45 N•m) of torque.
Replacing a Module
You can replace an Modicon X80 module at any time using another module with compatible
firmware. The replacement module obtains its operating parameters over the backplane
connection from the CPU. The transfer occurs immediately at the next cycle to the device.
NOTE: The operating parameters that the CPU sends to a replacement module do not include any
parameter values that were edited in the original module using explicit messaging SET commands.
48 EIO0000001584 06/2016
Installation
Installation Results
Applying power to the main local rack after the adapter module is installed can result in either:
Successful installation:
Initialization is finished.
Interconnections to other modules are validated (drop adapter module only).
Unsuccessful installation:
Initialization does not finish.
Interconnections to other modules are not validated (drop adapter modules only).
You can see the status of the installation on the adapter LED display (see page 19).
EIO0000001584 06/2016 49
Installation
NOTE: Set the rotary switches before you apply power to the module and before you download the
application.
The values you set are applied during a power cycle. If you change the switch settings after the
module has powered up, the Module Status LED (see page 19) is activated and a mismatch
message is logged in the module diagnostic.
If you want to return to the original setting of a modified rotary switch (and the other switch was
changed), turn the switch until the Module Status LED goes from red to green.
New values on the rotary switches are implemented at the next power cycle. Set the value before
starting the module (valid values: 00 ... 159).
The values on the rotary switches combine with the device prefix (for example, BMECRA_xxx or
BMXCRA_xxx) to create the device name (where xxx represents the value of the rotary switches).
The preceding figure shows the Tens switch set to 00 and the Ones switch set to 1, for a device
name of BMECRA_001.
NOTES:
The rotary switches can be manipulated with a small flat-tipped screwdriver.
No software is required to configure or enable the rotary switches.
Do not use the Stored and Clear IP settings on the Ones rotary switch as they do not apply to
remote I/O installations.
50 EIO0000001584 06/2016
Installation
Section 2.2
Remote I/O Infrastructure Cables
EIO0000001584 06/2016 51
Installation
Cable Installation
Introduction
A copper cable connection between two consecutive RIO drops cannot exceed 100 m. A fiber
cable connection between two consecutive RIO drops cannot exceed 15 km (single mode) or
2.5 km (multi-mode).
For more information, refer to racks installation and assembly (see Modicon M580, Hardware,
Reference Manual) and grounding and cabling (see Grounding and Electromagnetic Compatibility
of PLC Systems, Basic Principles and Measures, User Manual).
52 EIO0000001584 06/2016
Installation
NOTE: We recommend the use of shielded twisted pair CAT5e (10/100 Mbps) cables, especially
ConneXium 490NTC•000•• cables.
EIO0000001584 06/2016 53
Installation
Introduction
NOTICE
UNINTENTIONAL EQUIPMENT BEHAVIOR
Confirm that each module has a unique IP address. Duplicate IP addresses can cause
unpredicatable module/network behavior.
Failure to follow these instructions can result in equipment damage.
Each adapter module has a single IP address for its Ethernet ports. Therefore, the address conflict
detection algorithm (duplicate IP checking) is performed based on the status (link up, link down) of
the ports.
Link Down
These conditions apply when links are lost:
Link Up
These conditions apply when links are added:
54 EIO0000001584 06/2016
Installation
Conditions
An I/O connection can be lost to a BMECRA31210 or BMXCRA312•0 under these conditions:
Performing a hot swap by replacing an adapter module with the same type.
There is no RIO cable connection.
The I/O connection is closed while the CPU is reconfigured.
NOTE:
Configure the hold up time on the Unity Pro Parameter tab (see page 67). For more information,
refer to your system planning guide.
In hot standby systems, this situation occurs only when the adapter module loses the
connection to the primary and secondary CPUs.
NOTE: Configure the hold up time on the Unity Pro Parameter tab (see page 67). For more
information, refer to your system planning guide.
EIO0000001584 06/2016 55
Installation
56 EIO0000001584 06/2016
Modicon M580
Configuration and Programming with Unity Pro
EIO0000001584 06/2016
Chapter 3
Configuration and Programming with Unity Pro
Introduction
Use Unity Pro to configure your remote drops for Ethernet communications.
EIO0000001584 06/2016 57
Configuration and Programming with Unity Pro
Section 3.1
Creating a Unity Pro Project
Introduction
Use these instructions to create a Unity Pro project that allows communication between the I/O
scanner and RIO modules.
Stages
Here are the basic stages of the Unity Pro configuration:
Stage Description
1 Select a CPU and a power supply to create a new Unity Pro configuration. (Refer to the
Modicon M580 Hardware Reference Manual (see Modicon M580, Hardware, Reference
Manual)).
2 Configure a rack assembly for the RIO drop (in this section).
To help secure a Unity Pro project against unwanted modifications, refer to the Modicon M580
Hardware Reference Manual (see Modicon M580, Hardware, Reference Manual).
NOTE: These instructions assume that you have a working knowledge of Unity Pro.
Rack Considerations
RIO rack considerations:
The number of the first slot in a X80 rack is 0. Therefore, a 4-slot rack includes slot numbers 0,
1, 2, 3.
You can cut or copy other devices in the remote drop and paste them in any rack of the same
type, but you cannot move objects from a local rack to the drop or from a drop to the local rack.
Also, you can only perform these actions (cut, copy, paste) in the same device editor.
58 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
To add:
another RIO drop, click the rounded square at the bottom of the dialog
a remote drop extension rack, click the >> on the right side of the remote drop main rack
NOTE: When physically installing a remote drop extension rack, add Bus Extender modules and
cables (see page 45).
The number maximum of input channels that can be configured for analog modules is 236. In such
a configuration, no other modules can be configured in the RIO drop.
NOTE: If a serial Modbus network is added to an RIO drop, take in to account the number of
channels declared when calculating the number maximum of channel supported by the RIO drop.
EIO0000001584 06/2016 59
Configuration and Programming with Unity Pro
60 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
Section 3.2
Unity Pro Configuration for Ethernet RIO Modules
At a Glance
This section describes the module configuration tabs in Unity Pro. Use the parameters on these
tabs to configure services for a BM•CRA312•0 adapter module in an Ethernet RIO drop.
EIO0000001584 06/2016 61
Configuration and Programming with Unity Pro
About RSTP
The RSTP service supports the inherent network communications redundancy provided by a daisy
chain loop. The RIO communications automatically find an alternate path if a communication
disruption occurs (for example, a cable breaks or a device becomes inoperable). This service does
not require you to manually enable or disable the communication paths.
Changing RSTP parameters can affect subring diagnostics, I/O determinism, and network
recovery times.
Parameters
This table shows the Bridge priority parameters for the RSTP Operational State on the Unity Pro
RSTP tab:
62 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
About SNMP
An SNMP V1 agent is a software component of the SNMP service that runs on an adapter modules
and gives you access to diagnostic and management information for the modules. You can use
SNMP browsers, network management software, and other tools to access this data.
In addition, the SNMP agent can be configured with the IP addresses of 1 or 2 devices (typically
PCs that run network management software) to be the targets of event-driven trap messages.
Such messages inform the management device of events like cold starts and the inability of the
software to authenticate a device.
SNMP Parameters
These parameters are found on the Unity Pro SNMP tab:
EIO0000001584 06/2016 63
Configuration and Programming with Unity Pro
64 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
Online Behavior
The Service Port parameters are stored in the application, however you can reconfigure (change)
the parameters in the connected mode. Values that you reconfigure in the connected mode are
sent to the remote drop adapter module or the CPU module in explicit messages. If the module
does not respond to the explicit messages, a message appears.
NOTE: The changed values are not stored, so a mismatch can exist between the parameters that
are being used and those that are in the stored application.
NOTE: The Service Port configuration can be read and modified online using the Service Port
Control Object (see page 120) CIP object.
EIO0000001584 06/2016 65
Configuration and Programming with Unity Pro
Section 3.3
Unity Pro Configuration for RIO Drops
At a Glance
This section discusses the use of Unity Pro to configure the Ethernet RIO drop and its adapter
module. Included are descriptions of the parameters on the Configuration, Parameter, and Device
DDT tabs in Unity Pro.
66 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
Introduction
In the Unity Pro Parameters dialog, you can:
define or verify address information about the adapter module (name, IP address, and
subnetwork mask)
specify a hold-up time interval
specify I/O refresh rates
Parameter Descriptions
Address information parameters:
Parameter Comment
Device Name The name of the adapter module includes a fixed prefix and a number provided by the
rotary switch. Valid names conform to this structure: BM•CRA_xxx, where xxx equals
the 3-digit value selected on the rotary switch.
When the adapter is placed in the remote drop, the number is set to the device number.
The device number does not change if the device moves to a new location.
Each adapter needs to be assigned a unique number within the application. A message
like this appears when analysis reveals a duplicate number:
{EIO Bus (2) BME CRA 312 00}: Device name is not unique
IP Address You cannot edit the IP address and sub network (mask) fields.
Sub Network NOTE: The IP address is editable only in the IP Configuration tab of the CPU module.
The value for sub network is deduced from the CPU sub-network mask.
EIO0000001584 06/2016 67
Configuration and Programming with Unity Pro
Step Action
1 In the X80 performance EIO adapter window, select the Parameter tab.
2 Click the Update IP/DHCP configuration hyperlink.
NOTE: An Ethernet Network table that lists all RIO drops in the system appears.
3 Double-click the arrow in the Identifier column matching the desired RIO drop in the
BME•58_ECPU_EXT column.
4 Edit the Device Name in the Identifier field to reflect the new name
5 Close the Ethernet Network window and validate your project.
Parameter Comment
Hold up time The hold up time represents the time (ms) that device outputs are maintained in their
current states after a communication disruption and before taking their fallback values:
default value: 1000 ms
valid value range: 50...65,530 ms
If you assign a hold up time value that is less than the recommended minimum value, an I/O
module may move to its fallback state. When communications are restored, the I/O module restarts
and may not operate as anticipated.
There is only one hold up time for an RIO drop (not one for each task) based on the watchdog
value.
One RPI per task = task period/2
WARNING
UNINTENDED EQUIPMENT OPERATION
Do not configure a holdup time value that is less than the recommended minimum values, which
are:
for a periodic application: 6 x PAC scan time
for a cyclic application: configured watchdog value
Failure to follow these instructions can result in death, serious injury, or equipment damage.
68 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
Connection parameter:
Parameter Comment
CRA->Scanner RPI Inputs: The RPI is the input refresh rate at which the adapter module sends inputs
to the CPU with Ethernet I/O scanner service. The RPI is set in the subscribe field
for the adapter on the remote I/O drop:
periodic mode: default value = 1/2 MAST period.
cyclic mode: default value = 1/4 watchdog timeout period.
Scanner->CRA RPI Outputs: Outputs are passed from the CPU with Ethernet I/O scanner service to
the adapter. The default values are:
periodic mode: default value = 1.1 * MAST period.
cyclic mode: default value = 1/4 * watchdog timeout period.
You cannot edit this value. The outputs are published synchronously or
immediately at the end of the current MAST task.
NOTE: The default value for the watchdog timer is 250 ms. If the MAST task does
not finish within the watchdog period, the process times out.
NOTE:
When the Periodic mode is selected for the MAST task, the Period value allows the complete
execution of the logic. (The MAST can overrun when its execution time exceeds this value.)
Valid values: 1...255 ms (increment: 1 ms).
When Cyclic mode is selected for the MAST task, the outputs are sent upon the completion of
the task. The Watch Dog value (10 ... 1500 ms, increment: 10 ms, default = 250 ms) should be
greater than the execution time.
EIO0000001584 06/2016 69
Configuration and Programming with Unity Pro
Time Stamping
70 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
EIO0000001584 06/2016 71
Configuration and Programming with Unity Pro
Introduction
The Device DDT name of the device DDT (see Unity Pro, Program Languages and Structure,
Reference Manual ) is in this format: MOD_COM_#. In Unity Pro, the # symbol represents the order
of the instances of the Device DDT creations. The first created is named MOD_COM_1; the second
created is named MOD_COM_2.
NOTE: These instructions assume that you have already added a drop to your Unity Pro project
(see page 43).
The Implicit device DDT field contains a default name and type.
72 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
Drop Parameters
In the Unity Pro Device DDT dialog, you can configure these parameters for the RIO drop:
Parameter Description
Implicit device DDT Name The default name of the device DDT includes the module type, the
number of channels, and a suffix that indicates the insertion number (for
example, MOD_TOR_16_128).
Type module type (read only)
Goto details Click this link to the Device DDT Data Editor screen.
Diagnostic Parameters
Click the Goto details button on the Device DDT screen to view the Variables tab in the Data Editor.
The bits indicates healthy (1) or unhealthy/unconfigured (0).
View the drop diagnostic parameters in T_M_CRA_EXT_IN for an RIO drop module:
EIO0000001584 06/2016 73
Configuration and Programming with Unity Pro
74 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
EIO0000001584 06/2016 75
Configuration and Programming with Unity Pro
76 EIO0000001584 06/2016
Configuration and Programming with Unity Pro
EIO0000001584 06/2016 77
Configuration and Programming with Unity Pro
78 EIO0000001584 06/2016
Modicon M580
Implicit and Explicit Messaging
EIO0000001584 06/2016
Chapter 4
Implicit and Explicit Messaging
EIO0000001584 06/2016 79
Implicit and Explicit Messaging
Explicit Messaging
80 EIO0000001584 06/2016
Implicit and Explicit Messaging
Task Management
This topic explains implicit I/O and the relationship between the task configuration and the RIO
implicit exchanges.
Implicit messaging maintains open connections for real-time communications of a predefined
nature between consumers and producers. Implicit I/O exchanges contain control data and a
connection identifier.
EtherNet/IP uses the TCP/IP and UDP/IP protocols to implement implicit messaging.
Step Action
1 Go to the Properties of MAST dialog box in Unity Pro (Tools → Project Browser → Project →
Program → Tasks → MAST).
2 Right-click MAST → Properties to open the Properties of MAST dialog.
3 Configure the parameters as needed.
Step Action
1 Go to the Properties of FAST dialog box in Unity Pro (Tools → Project Browser → Project →
Program → Tasks → FAST).
2 Right-click FAST → Properties to open the Properties of FAST dialog.
3 Configure the parameters as needed.
EIO0000001584 06/2016 81
Implicit and Explicit Messaging
Step Action
1 Go to the Properties of AUX0 dialog box in Unity Pro (Tools → Project Browser → Project →
Program → Tasks → AUX0).
2 Right-click AUX0 → Properties to open the Properties of AUX0 dialog.
3 Configure the parameters as needed.
Step Action
1 Go to the Properties of AUX1 dialog box in Unity Pro (Tools → Project Browser → Project →
Program → Tasks → AUX1).
2 Right-click AUX1 → Properties to open the Properties of AUX1 dialog.
3 Configure the parameters as needed.
82 EIO0000001584 06/2016
Modicon M580
Diagnostics
EIO0000001584 06/2016
Chapter 5
Diagnostics
Diagnostics
Overview
This chapter describes the diagnostics for the Modicon M580 modules. For details on diagnostics
at the system level, refer to the systems diagnostics topic in your system planning guide.
EIO0000001584 06/2016 83
Diagnostics
Section 5.1
Service Port Management
Introduction
A BME•58••40 RIO scanner module and an RIO adapter modules (BM•CRA31210) support the
configuration of the SERVICE port without requiring you to rebuild or download your application.
Adapter Modules
You can send explicit messages with an EtherNet/IP tool for the configuration of the SERVICE port
on the BM•CRA31210 modules. For details, refer to information about EtherNet/IP CIP objects in
your system hardware reference manual and SERVICE port configuration for adapter modules
(see page 65).
Cycling Power
The online configuration of the SERVICE port is volatile. The following may result when power is
cycled to the adapter module while the application is being applied:
The configuration can be lost.
The configuration in the application can be applied to the SERVICE port.
84 EIO0000001584 06/2016
Diagnostics
Section 5.2
Diagnostics Available through the CPU
System Diagnostics
Introduction
System diagnostics are performed by using:
system bits (%S) and system words (%SW)
Modbus/TCP (see page 87) or EtherNet/IP CIP (see page 88) requests
diagnostic parameters in the T_CRA_EXT_IN (see page 73) DDT.
The CPU I/O scanner monitors RIO drops and module health. The adapter modules in the RIO
drops transmit detected errors in the drop modules to the CPU via implicit messages
(see page 81). The detected errors are stored in the global diagnostic buffers of the CPU and in
the diagnostic buffer of the individual drop modules.
The CPU updates the detected error buffers. Health bits are updated in the CPU only if the adapter
of the concerned drop communicates with the CPU. If these modules cannot communicate, the
concerned health bits are set to 0.
NOTE: Refer to the Unity Pro Program Languages and Structure Reference Manual complete
explanations of the system bits and words.
EIO0000001584 06/2016 85
Diagnostics
Legend:
(1) Accessible through explicit Modbus/TCP (see page 87) requests
(2) Accessible through explicit EtherNet/IP CIP (see page 88) requests
NOTE: Remember:
The slots in a drop are numbed 0...n.
The rack numbers are used in remote drops:
0: main rack in the RIO drop
86 EIO0000001584 06/2016
Diagnostics
Section 5.3
Diagnostics Available through Modbus/TCP
Diagnostic
Function code 8, subcode 22: Modbus function code 08 provides a variety of diagnostic functions:
EIO0000001584 06/2016 87
Diagnostics
Section 5.4
Diagnostics Available through EtherNet/IP CIP Objects
At a Glance
M580 applications use CIP within a producer/consumer model to provide communication services
in an industrial environment. This section describes the available CIP objects for X80 modules in
an M580 system.
88 EIO0000001584 06/2016
Diagnostics
Overview
The remote I/O adapter module can access CIP data and services located in connected devices.
The CIP objects and their content depend on the design of each device.
CIP object data and content are exposed and accessed hierarchically in the following nested
levels:
NOTE:
You can use explicit messaging to access these items:
Access a collection of instance attributes by including only the class and instance values for the
object in the explicit message.
Access a single attribute by adding a specific attribute value to the explicit message with the
class and instance values for the object.
When the local slave service for the adapter is activated, remote devices on the remote I/O drop
can send explicit messages to the CIP object structure of the module. Then you can access module
data or execute module commands.
This chapter describes the CIP objects that the adapter exposes to remote devices.
EIO0000001584 06/2016 89
Diagnostics
Identity Object
Class ID
01
Instance IDs
The Identity object presents 2 instances:
0: class
1: instance
Attributes
Identity object attributes are associated with each instance, as follows:
Instance ID = 0 (class attributes):
90 EIO0000001584 06/2016
Diagnostics
Services
The Identity object supports the following services:
EIO0000001584 06/2016 91
Diagnostics
Assembly Object
Overview
You can send an explicit message to the Assembly object only when no other connections have
been established that read from or write to this object. For example, you can send an explicit
message to the Assembly object if a local slave instance is enabled, but no other module is
scanning that local slave.
Class ID
04
Instance IDs
The Assembly object presents the following instance identifiers:
0: class
101, 102, 111, 112, 121, 122: instance
Attributes
The Assembly object consists of the following attributes:
Instance ID = 0 (class attributes):
Instance attributes:
92 EIO0000001584 06/2016
Diagnostics
Services
The Assembly object supports the following services:
EIO0000001584 06/2016 93
Diagnostics
Class ID
06
Instance IDs
The Connection Manager object presents 2 instance values:
0: class
1: instance
Attributes
Connection Manager object attributes are associated with each instance, as follows:
Instance ID = 0 (class attributes):
94 EIO0000001584 06/2016
Diagnostics
Services
The Connection Manager object supports the following services:
Overview
The QoS object implements the Differentiated Services Code Point (DSCP or DiffServe) values to
prioritize Ethernet messages.
Class ID
48 (hex), 72 (decimal)
EIO0000001584 06/2016 95
Diagnostics
Instance IDs
The QoS object presents 2 instance values:
0: class
1: instance
Attributes
The QoS object consists of the following attributes:
Instance ID = 0 (class attributes):
NOTE: A change in the instance attribute value takes effect on device restart, for configurations
made from flash memory.
96 EIO0000001584 06/2016
Diagnostics
Services
The QoS object supports the following services:
EIO0000001584 06/2016 97
Diagnostics
Class ID
F5 (hex), 245 (decimal)
Instance IDs
The TCP/IP interface object presents 2 instance values:
0: class
1: instance
Attributes
TCP/IP interface object attributes are associated with each instance, as follows:
Instance ID = 0 (class attributes):
98 EIO0000001584 06/2016
Diagnostics
Services
The TCP/IP interface object supports the following services:
EIO0000001584 06/2016 99
Diagnostics
Class ID
F6 (hex), 246 (decimal)
Instance IDs
The Ethernet Link object presents the following instance values (for an BMECRA31210):
0: class
1: port (ETH1 (see page 17))
2: port (ETH2)
3: port (ETH3)
4: port (Internal backplane port 255)
Attributes
The Ethernet Link object presents the following attributes:
Instance ID = 0 (class attributes):
Services
The Ethernet Link object supports the following services:
Class ID
350 (hex), 848 (decimal)
Instance IDs
The EtherNetP/IP Interface object presents 2 instance values:
0: class
1: instance
Attributes
EtherNet/IP Interface Diagnostics object attributes are associated with each instance, as follows:
Instance ID = 0 (class attributes):
X = supported
— = not supported
Services
The EtherNet/IP Interface Diagnostics object supports the following services:
Class ID
352 (hex), 850 (decimal)
Instance IDs
The I/O Connection Diagnostics object presents the following instance values:
0: class
1...256: instances
NOTE: The Instance ID number = the Connection ID. For M580 specifically, you can look up the
Connection ID on the DTM Device List screen.
Attributes
I/O Connection Diagnostics object attributes are associated with each instance, as follows:
Instance ID = 0 (class attributes):
The following values describe the structure of the instance attributes: CIP connection state,
Input Communication status, and Output communication status:
Services
The EtherNet/IP Interface Diagnostics object supports the following services:
Overview
The EtherNet/IP Explicit Connection Diagnostics object presents the instances, attributes and
services described below.
Class ID
353 (hex), 851 (decimal)
Instance IDs
The EtherNet/IP Explicit Connection Diagnostics object presents two instance values:
0: class
1...N: instance (N = maximum concurrent number of explicit connections)
Attributes
EtherNet/IP Explicit Connection Diagnostics object attributes are associated with each instance,
as follows:
Instance ID = 0 (class attributes):
Services
The EtherNet/IP Explicit Connection Diagnostics object performs the following services upon the
listed object type:
Overview
The EtherNet/IP Explicit Connection Diagnostics List object presents the instances, attributes and
services described below.
Class ID
354 (hex), 852 (decimal)
Instance IDs
The EtherNet/IP Explicit Connection Diagnostics List object presents two instance values:
0: class
1: instance
Attributes
EtherNet/IP Explicit Connection Diagnostics List object attributes are associated with each
instance, as follows:
Instance ID = 0 (class attributes):
Services
The EtherNet/IP Explicit Connection Diagnostics object performs the following services upon the
listed object types:
Class ID
355 (hex), 853 (decimal)
Instance IDs
The RSTP Diagnostics object presents these instance values:
0: class
1... N: instance
Attributes
RSTP Diagnostics object attributes are associated with each instance.
Instance ID = 0 (class attributes):
State UINT X X
Enable UINT X X
Path cost UDINT X X
Designated root String X X
Designated cost UDINT X X
Designated bridge String X X
Designated port String X X
Forward transitions UDINT X X Refer to RFC-4188 for attribute definitions
count and value range.
Services:
Get_and_Clear: The current value of
this parameter is returned with the
response message.
other services: The current value of
this parameter is returned without
being cleared.
X = supported
— = not supported
Services
The RSTP Diagnostics object performs these services:
Class ID
400 (hex), 1024 (decimal)
Instance IDs
The Service Port Control object presents these instance values:
0: class
1: instance
Attributes
Service Port Control object attributes are associated with each instance.
Required class attributes (instance 0):
NOTE:
If the SERVICE port is not configured for port mirroring, the mirror attribute is ignored. If the
value of a parameter request is outside the valid range, the service request is ignored.
In port mirroring mode, the SERVICE port acts like a read-only port. That is, you cannot access
devices (ping, connection to Unity Pro, and so on) through the SERVICE port.
Services
The Service Port Control object supports these services:
Class ID
405 (hex), 1029 (decimal)
Instance IDs
The SNTP diagnostics list object presents the following instance values:
0: class
1: instance
Attributes
SNTP diagnostics object attributes are associated with each instance.
Instance ID = 0 (class attributes):
B Current date and time DATE_AND X — {time_of_day UDINT, date UINT} (see CIP
_TIME specification)
C Daylight savings status UDINT X — 1: Daylight savings are enabled and the
current date/time is within the applicable
period.
2: NTP daylight savings are not enabled
or enabled but not within the applicable
period.
D Time since last update DINT X — Amount of time elapsed since a valid
response from the NTP server (in 100 ms
increments)
-1: not updated
NOTE: All attributes are required in the implementation.
X = supported
— = not supported
Services
The SNTP diagnostics object support the following services:
Class ID
407 (hex), 1031(decimal)
Instance IDs
The Ethernet Backplane Diagnostics object presents the following instance values:
0: class
1: instance
Attributes
Ethernet Backplane Diagnostics object attributes are associated with each instance, as follows:
Instance ID = 0 (class attributes):
Section 5.5
Diagnostics Available through Unity Pro
Introduction
The Modicon M580 modules support online actions.
Tasks
Use online actions to perform these tasks:
Display EtherNet/IP objects for a remote EtherNet/IP device.
Ping the CPU remote I/O scanner module, a remote EtherNet/IP, or a Modbus TCP device to
confirm it is active on the Ethernet network.
Connect to a remote device to perform these actions:
View the remote device’s default parameter settings.
View the remote device’s current parameter settings.
Edit and download to the remote device its editable parameter settings.
NOTE: Quantum 140CRA31200 adapter modules do not support FAST and AUX0/AUX1 tasks.
BMECRA312•0 adpater modules do.
NOTE: Modicon M580 BMECRA312•0 adapter modules support FAST and AUX• tasks
(see Quantum EIO, Remote I/O Modules, Installation and Configuration Guide). Quantum
140CRA31200 adapter modules do not.
Chapter 6
Firmware Upgrade
Firmware Upgrade
Overview
Use these procedures to upgrade the firmware for the RIO adapter:
Stage Description
1 Download and install Unity Loader software.
2 Configure and store IP parameters (optional).
3 Connect your configuration PC to the RIO adapter.
4 Transfer the firmware upgrade to the RIO adapter or the Ethernet backplane.
Step Action
1 Enter the web address for Schneider Electric (www.schneider-electric.com) in an Internet
browser.
2 In the Search from input field, enter the phrase Unity Loader and press Enter.
3 Examine the search results and select the appropriate entry for the Unity Loader software.
4 Follow the on-screen instructions to download both the Unity Loader installation software and
any necessary installation instructions.
5 Run the Unity Loader setup file and follow the instructions (on the screen and in the downloaded
documentation) to install Unity Loader.
Parameter Description
Default IP Address The default IP address starts with 10.10 and uses the last 2 bytes of the MAC
address. As an example, a device with the MAC address of 00:00:54:10:8A:05
has a default IP address of 10.10.138.5 (0x8A=138, 0x05=5).
Default Sub-Network Mask The default mask is 255.0.0.0 (a class A mask).
Default Gateway Address The default gateway address is identical to the default IP address.
The default address is based on the adapter MAC address. This makes it possible for several
Schneider Electric devices to use their default network configurations on the same network.
To configure and store IP parameters that are not the default values for the remote drop adapter:
Step Action
1 Start or re-start the adapter with the rotary switch set toStored.
2 Store the IP address by sending a explicit message to the TCP/IP Interface Object
(see page 98) (Attribute ID 05: Interface Configuration).
NOTE: The adapter uses the stored IP parameters only after a power cycle.
Upgrade Procedure
Do not interrupt the firmware download process by:
allowing an interruption to the power or communications
closing the Unity Loader software
If the firmware download process is interrupted, the new firmware is not installed and the adapter
continues to use the old firmware. If an interruption occurs, restart the process.
NOTE: If the download is not completed, there is a message saying that the upgrade was
unsuccessful.
To update the firmware for the RIO adapter:
Step Action
1 Open Unity Loader on your PC. (Start → Programs → Schneider Electric → Unity Loader)
Result: Unity Loader opens and displays the Project tab.
2 At the bottom of the tab in the Connection area, connect to the module:
In the Media list, select Ethernet.
In the Address field, type in the IP address of the adapter, which is either:
configured: The adapter is already communicating on the network and the IP address for
the module is configured in the application in the BME•58••40 CPU module.
default: The adapter’s rotary switch position is Stored and you did not already store valid
IP parameters.
Click Connect.
3 After Unity Loader has connected to the module, click the Firmware tab in the Unity Loader
dialog.
4 In the PC area, click the ellipsis (...) button to open a dialog where you can navigate to and
select the firmware file for the adapter module. The firmware is contained in a Unity Loader file
(.LDX extension).
NOTE: When using the BMECRA31210, you can also update firmware for a BMEXBP••00.
After you select the firmware file and close the dialog, the selected revision of this firmware is
displayed in the list on the left, and the current version of the firmware is displayed in the list on
the right.
5 When the arrow in the middle of the Unity Loader dialog is green, click Transfer.
NOTE: Only click Transfer if the arrow is green. A yellow arrow indicates that the firmware file
on your computer is the same version or newer than the file selected for transfer; a red arrow
indicates that the firmware on the computer is not compatible with the RIO adapter.
6 Click Yes on the 2 dialogs that appear.
7 The Transferring data to PLC opens, which indicates the transfer status with the blue bars at
the bottom of the screen.
8 After the transfer is complete, click Close.
9 In the Unity Loader software, click Disconnect and close the window.
10 Reboot the module to finalize the firmware update.
From 1 instance of Unity Loader, you can only update 1 device. To update several devices at the
same time, open additional instances of Unity Loader. In this case, additional dialogs. Click Yes to
close each dialog.
The upgrade process takes approximately 3 minutes:
firmware upgrade (approximately 2 minutes)
reboot, reestablish I/O connections (1 minute)
During the firmware upgrade, the I/O communication with the adapter module is interrupted. After
the hold up time (see page 67) expires, the output modules move to the pre-configured fallback
setting (a value of 0, 1, or hold last value).
Glossary
!
%I
According to the CEI standard, %I indicates a language object of type discrete IN.
%IW
According to the CEI standard, %IW indicates a language object of type analog IN.
%M
According to the CEI standard, %M indicates a language object of type memory bit.
%MW
According to the CEI standard, %MW indicates a language object of type memory word.
%Q
According to the CEI standard, %Q indicates a language object of type discrete OUT.
%QW
According to the CEI standard, %QW indicates a language object of type analog OUT.
%SW
According to the CEI standard, %SW indicates a language object of type system word.
A
adapter
An adapter is the target of real-time I/O data connection requests from scanners. It cannot send or
receive real-time I/O data unless it is configured to do so by a scanner, and it does not store or
originate the data communications parameters necessary to establish the connection. An adapter
accepts explicit message requests (connected and unconnected) from other devices.
advanced mode
In Unity Pro, advanced mode is a selection that displays expert-level configuration properties that
help define Ethernet connections. Because these properties should be edited only by people with
a good understanding of EtherNet/IP communication protocols, they can be hidden or displayed,
depending upon the qualifications of the specific user.
architecture
Architecture describes a framework for the specification of a network that is constructed of these
components:
physical components and their functional organization and configuration
operational principles and procedures
data formats used in its operation
ARRAY
An ARRAY is a table containing elements of a single type. This is the syntax: ARRAY [<limits>]
OF <Type>
Example: ARRAY [1..2] OF BOOL is a one-dimensional table with two elements of type BOOL.
ARRAY [1..10, 1..20] OF INT is a two-dimensional table with 10x20 elements of type INT.
ART
(application response time) The time a CPU application takes to react to a given input. ART is
measured from the time a physical signal in the CPU turns on and triggers a write command until
the remote output turns on to signify that the data has been received.
AUX
An (AUX) task is an optional, periodic processor task that is run through its programming software.
The AUX task is used to execute a part of the application requiring a low priority. This task is
executed only if the MAST and FAST tasks have nothing to execute. The AUX task has two
sections:
IN: Inputs are copied to the IN section before execution of the AUX task.
OUT: Outputs are copied to the OUT section after execution of the AUX task.
B
BCD
(binary-coded decimal) Binary encoding of decimal numbers.
BOOL
(boolean type) This is the basic data type in computing. A BOOL variable can have either of these
values: 0 (FALSE) or 1 (TRUE).
A bit extracted from a word is of type BOOL, for example: %MW10.4.
BOOTP
(bootstrap protocol) A UDP network protocol that can be used by a network client to automatically
obtain an IP address from a server. The client identifies itself to the server using its MAC address.
The server, which maintains a pre-configured table of client device MAC addresses and associated
IP addresses, sends the client its defined IP address. The BOOTP service utilizes UDP ports 67
and 68.
broadcast
A message sent to all devices in a broadcast domain.
C
CCOTF
(change configuration on the fly) A feature of Unity Pro that allows a module hardware change in
the system configuration while the system is operating. This change does not impact active
operations.
CIP™
(common industrial protocol) A comprehensive suite of messages and services for the collection
of manufacturing automation applications (control, safety, synchronization, motion, configuration
and information). CIP allows users to integrate these manufacturing applications with enterprise-
level Ethernet networks and the internet. CIP is the core protocol of EtherNet/IP.
class 1 connection
A CIP transport class 1 connection used for I/O data transmission via implicit messaging between
EtherNet/IP devices.
class 3 connection
A CIP transport class 3 connection used for explicit messaging between EtherNet/IP devices.
connected messaging
In EtherNet/IP, connected messaging uses a CIP connection for communication. A connected
message is a logical relationship between two or more application objects on different nodes. The
connection establishes a virtual circuit in advance for a particular purpose, such as frequent explicit
messages or real-time I/O data transfers.
connection
A virtual circuit between two or more network devices, created prior to the transmission of data.
After a connection is established, a series of data is transmitted over the same communication
path, without the need to include routing information, including source and destination address,
with each piece of data.
connection originator
The EtherNet/IP network node that initiates a connection request for I/O data transfer or explicit
messaging.
connectionless
Describes communication between two network devices, whereby data is sent without prior
arrangement between the two devices. Each piece of transmitted data also includes routing
information, including source and destination address.
control network
An Ethernet-based network containing PACs, SCADA systems, an NTP server, PCs, AMS,
switches, etc. Two kinds of topologies are supported:
flat: All modules and devices in this network belong to same subnet.
2 levels: The network is split into an operation network and an inter-controller network. These
two networks can be physically independent, but are generally linked by a routing device.
CPU
(central processing unit) The CPU, also known as the processor or controller, is the brain of an
industrial manufacturing process. It automates a process as opposed to relay control systems.
CPUs are computers suited to survive the harsh conditions of an industrial environment.
D
DDT
(derived data type) A derived data type is a set of elements with the same type (ARRAY) or with
different types (structure).
determinism
For a defined application and architecture, you can predict that the delay between an event
(change of value of an input) and the corresponding change of a controller output is a finite time t,
smaller than the deadline required by your process.
Device DDT (DDDT)
A Device DDT is a DDT predefined by the manufacturer and not modifiable by user. It contains the
I/O language elements of an I/O module.
device network
An Ethernet-based network within a remote I/O network that contains both remote I/O and
distributed I/O devices. Devices connected on this network follow specific rules to allow remote I/O
determinism.
device network
An Ethernet-based network within an RIO network that contains both RIO and distributed
equipment. Devices connected on this network follow specific rules to allow RIO determinism.
DFB
(derived function block) DFB types are function blocks that can be defined by the user in ST, IL,
LD or FBD language.
Using these DFB types in an application makes it possible to:
simplify the design and entry of the program
make the program easier to read
make it easier to debug
reduce the amount of code generated
DHCP
(dynamic host configuration protocol) An extension of the BOOTP communications protocol that
provides for the automatic assignment of IP addressing settings, including IP address, subnet
mask, gateway IP address, and DNS server names. DHCP does not require the maintenance of a
table identifying each network device. The client identifies itself to the DHCP server using either its
MAC address, or a uniquely assigned device identifier. The DHCP service utilizes UDP ports 67
and 68.
DIO
(distributed I/O) Legacy term for distributed equipment. DRSs use DIO ports to connect distributed
equipment.
DIO cloud
A group of distributed equipment that is not required to support RSTP. DIO clouds require only a
single (non-ring) copper wire connection. They can be connected to some of the copper ports on
DRSs, or they can be connected directly to the CPU or Ethernet communications modules in the
local rack. DIO clouds cannot be connected to sub-rings.
DIO network
A network containing distributed equipment, in which I/O scanning is performed by a CPU with DIO
scanner service on the local rack. DIO network traffic is delivered after RIO traffic, which takes
priority in an RIO network.
distributed equipment
Any Ethernet device (Schneider Electric device, PC, servers, or third-party devices) that supports
exchange with a CPU or other Ethernet I/O scanner service.
DNS
(domain name server/service) A service that translates an alpha-numeric domain name into an IP
address, the unique identifier of a device on the network.
domain name
An alpha-numeric string that identifies a device on the internet, and which appears as the primary
component of a web site’s uniform resource locator (URL). For example, the domain name
schneider-electric.com is the primary component of the URL www.schneider-electric.com.
Each domain name is assigned as part of the domain name system, and is associated with an IP
address.
Also called a host name.
DRS
(dual-ring switch) A ConneXium extended managed switch that has been configured to operate on
an Ethernet network. Predefined configuration files are provided by Schneider Electric to
downloaded to a DRS to support the special features of the main ring / sub-ring architecture.
DSCP
(differentiated service code points) This 6-bit field is in the header of an IP packet to classify and
prioritize traffic.
DST
(daylight saving time) DST is also called summer time and is a practice consisting of adjusting
forward the clock near the start of spring and adjusting it backward near the start of autumn.
DT
(date and time) The DT type, encoded in BCD in a 64-bit format, contains this information:
the year encoded in a 16-bit field
the month encoded in an 8-bit field
DTM
(device type manager) A DTM is a device driver running on the host PC. It provides a unified
structure for accessing device parameters, configuring and operating the devices, and
troubleshooting devices. DTMs can range from a simple graphical user interface (GUI) for setting
device parameters to a highly sophisticated application capable of performing complex real-time
calculations for diagnosis and maintenance purposes. In the context of a DTM, a device can be a
communications module or a remote device on the network.
See FDT.
E
EDS
(electronic data sheet) EDS are simple text files that describe the configuration capabilities of a
device. EDS files are generated and maintained by the manufacturer of the device.
EF
(elementary function) This is a block used in a program which performs a predefined logical
function.
A function does not have any information on the internal state. Several calls to the same function
using the same input parameters will return the same output values. You will find information on
the graphic form of the function call in the [functional block (instance)]. Unlike a call to a function
block, function calls include only an output which is not named and whose name is identical to that
of the function. In FBD, each call is indicated by a unique [number] via the graphic block. This
number is managed automatically and cannot be modified.
Position and configure these functions in your program in order to execute your application.
You can also develop other functions using the SDKC development kit.
EFB
(elementary function block) This is a block used in a program which performs a predefined logical
function.
EFBs have states and internal parameters. Even if the inputs are identical, the output values may
differ. For example, a counter has an output indicating that the preselection value has been
reached. This output is set to 1 when the current value is equal to the preselection value.
EIO network
Ethernet I/O) An Ethernet-based network that contains three types of devices:
local rack
X80 EIO drop, or a Quantum EIO drop (using a BM•CRA312•0 adapter module), or a
BMENOS0300 network option switch module
ConneXium extended dual-ring switch (DRS)
NOTE: Distributed equipment may also participate in an EIO network via connection to DRSs or
the service port of X80 EIO adapter modules.
EN
EN stands for ENable; it is an optional block input. When the EN input is enabled, an ENO output is
set automatically.
If EN = 0, the block is not enabled; its internal program is not executed, and ENO is set to 0.
If EN = 1, the block's internal program is run and ENO is set to 1. If a runtime error is detected, ENO
is set to 0.
If the EN input is not connected, it is set automatically to 1.
ENO
ENO stands for Error NOtification; this is the output associated with the optional input EN.
If ENO is set to 0 (either because EN = 0 or if a runtime error is detected):
The status of the function block outputs remains the same as it was during the previous
scanning cycle that executed correctly.
The output(s) of the function, as well as the procedures, are set to 0.
Ethernet
A 10 Mb/s, 100 Mb/s, or 1 Gb/s, CSMA/CD, frame-based LAN that can run over copper twisted pair
or fiber optic cable, or wireless. The IEEE standard 802.3 defines the rules for configuring a wired
Ethernet network; the IEEE standard 802.11 defines the rules for configuring a wireless Ethernet
network. Common forms include 10BASE-T, 100BASE-TX, and 1000BASE-T, which can utilize
category 5e copper twisted pair cables and RJ45 modular connectors.
Ethernet DIO scanner service
This embedded DIO scanner service of M580 CPUs manages distributed equipment on an M580
device network.
Ethernet I/O scanner service
This embedded Ethernet I/O scanner service of M580 CPUs manages distributed equipment and
RIO drops on an M580 device network.
EtherNet/IP™
A network communication protocol for industrial automation applications that combines the
standard internet transmission protocols of TCP/IP and UDP with the application layer common
industrial protocol (CIP) to support both high speed data exchange and industrial control.
EtherNet/IP employs electronic data sheets (EDS) to classify each network device and its
functionality.
explicit messaging
TCP/IP-based messaging for Modbus TCP and EtherNet/IP. It is used for point-to-point,
client/server messages that include both data, typically unscheduled information between a client
and a server, and routing information. In EtherNet/IP, explicit messaging is considered class 3 type
messaging, and can be connection-based or connectionless.
explicit messaging client
(explicit messaging client class) The device class defined by the ODVA for EtherNet/IP nodes that
only support explicit messaging as a client. HMI and SCADA systems are common examples of
this device class.
F
FAST
A FAST task is an optional, periodic processor task that identifies high priority, multiple scan
requests, which is run through its programming software. A FAST task can schedule selected I/O
modules to have their logic solved more than once per scan. The FAST task has two sections:
IN: Inputs are copied to the IN section before execution of the FAST task.
OUT: Outputs are copied to the OUT section after execution of the FAST task.
FBD
(function block diagram) A graphical programming language that works like a flowchart. By adding
simple logical blocks (AND, OR, etc.), each function or function block in the program is represented
in this graphical format. For each block, the inputs are on the left and the outputs on the right. Block
outputs can be linked to inputs of other blocks in order to create complex expressions.
FDR
(fast device replacement) A service that uses configuration software to replace an inoperable
product.
FDT
(field device tool) The technology that harmonizes communication between field devices and the
system host.
FTP
(file transfer protocol) A protocol that copies a file from one host to another over a TCP/IP-based
network, such as the internet. FTP uses a client-server architecture as well as separate control and
data connections between the client and server.
full duplex
The ability of two networked devices to independently and simultaneously communicate with each
other in both directions.
function block diagram
See FBD.
G
gateway
A gateway device interconnects two different networks, sometimes through different network
protocols. When it connects networks based on different protocols, a gateway converts a datagram
from one protocol stack into the other. When used to connect two IP-based networks, a gateway
(also called a router) has two separate IP addresses, one on each network.
H
harsh environment
Resistance to hydrocarbons, industrial oils, detergents and solder chips. Relative humidity up to
100%, saline atmosphere, significant temperature variations, operating temperature between -
10°C and + 70 °C, or in mobile installations. For hardened (H) devices, the relative humidity is up
to 95% and the operating temperature is between -25°C and + 70 °C.
HART
(highway addressable remote transducer) A bi-directional communication protocol for sending and
receiving digital information across analog wires between a control or monitoring system and smart
devices.
HART is the global standard for providing data access between host systems and intelligent field
instruments. A host can be any software application from a technician's hand-held device or laptop
to a plant's process control, asset management, or other system using any control platform.
I
I/O scanner
An Ethernet service that continuously polls I/O modules to collect data, status, event, and
diagnostics information. This process monitors inputs and controls outputs. This service supports
both RIO and DIO logic scanning.
IEC 61131-3
International standard: programmable logic controllers
Part 3: programming languages
IGMP
(internet group management protocol) This internet standard for multicasting allows a host to
subscribe to a particular multicast group.
IL
(instruction list) This language is a series of basic instructions. It is very close to assembly
language used to program processors. Each instruction is made up of an instruction code and an
operand.
implicit messaging
UDP/IP-based class 1 connected messaging for EtherNet/IP. Implicit messaging maintains an
open connection for the scheduled transfer of control data between a producer and consumer.
Because an open connection is maintained, each message contains primarily data, without the
overhead of object information, plus a connection identifier.
INT
(INTeger) (encoded in 16 bits) The upper/lower limits are as follows: -(2 to the power of 15) to (2
to the power of 15) - 1.
Example: -32768, 32767, 2#1111110001001001, 16#9FA4.
inter-controller network
An Ethernet-based network that is part of the control network, and provides data exchange
between controllers and engineering tools (programming, asset management system (AMS)).
IODDT
(input/output derived data type) A structured data type representing a module, or a channel of a
CPU. Each application expert module possesses its own IODDTs.
IP address
The 32-bit identifier, consisting of both a network address and a host address assigned to a device
connected to a TCP/IP network.
IPsec
(internet protocol security) An open set of protocol standards that make IP communication
sessions private and secure for traffic between modules using IPsec, developed by the internet
engineering task force (IETF). The IPsec authentication and encryption algorithms require user-
defined cryptographic keys that process each communications packet in an IPsec session.
isolated DIO network
An Ethernet-based network containing distributed equipment that does not participate in an RIO
network.
L
LD
(ladder diagram) A programming language that represents instructions to be executed as graphical
diagrams very similar to electrical diagrams (contacts, coils, etc.).
literal value of an integer
A literal value of an integer is used to enter integer values in the decimal system. Values may be
preceded by the "+" and "-" signs. Underscore signs (_) separating numbers are not significant.
Example:
-12, 0, 123_456, +986
local rack
An M580 rack containing the CPU and a power supply. A local rack consists of one or two racks:
the main rack and the extended rack, which belongs to the same family as the main rack. The
extended rack is optional.
local slave
The functionality offered by Schneider Electric EtherNet/IP communication modules that allows a
scanner to take the role of an adapter. The local slave enables the module to publish data via
implicit messaging connections. Local slave is typically used in peer-to-peer exchanges between
PACs.
M
M580 Ethernet I/O device
An Ethernet device that provides automatic network recovery and deterministic RIO performance.
The time it takes to resolve an RIO logic scan can be calculated, and the system can recover
quickly from a communication disruption. M580 Ethernet I/O devices include:
local rack (including a CPU with Ethernet I/O scanner service)
RIO drop (including an Ethernet X80 EIO adapter module)
DRS switch with a predefined configuraton
main ring
The main ring of an Ethernet RIO network. The ring contains RIO modules and a local rack
(containing a CPU with Ethernet I/O scanner service) and a power supply module.
MAST
A master (MAST) task is a deterministic processor task that is run through its programming
software. The MAST task schedules the RIO module logic to be solved in every I/O scan. The
MAST task has two sections:
IN: Inputs are copied to the IN section before execution of the MAST task.
OUT: Outputs are copied to the OUT section after execution of the MAST task.
MB/TCP
(Modbus over TCP protocol) This is a Modbus variant used for communications over TCP/IP
networks.
MIB
(management information base) A virtual database used for managing the objects in a
communications network. See SNMP.
Modbus
Modbus is an application layer messaging protocol. Modbus provides client and server
communications between devices connected on different types of buses or networks. Modbus
offers many services specified by function codes.
multicast
A special form of broadcast where copies of the packet are delivered to only a specified subset of
network destinations. Implicit messaging typically uses multicast format for communications in an
EtherNet/IP network.
N
network
There are two meanings:
In a ladder diagram:
A network is a set of interconnected graphic elements. The scope of a network is local,
concerning the organizational unit (section) of the program containing the network.
With expert communication modules:
A network is a set of stations that intercommunicate. The term network is also used to define a
group interconnected graphic elements. This group then makes up part of a program that may
comprise a group of networks.
NIM
(network interface module) A NIM resides in the first position on an STB island (leftmost on the
physical setup). The NIM provides the interface between the I/O modules and the fieldbus master.
It is the only module on the island that is fieldbus-dependent — a different NIM is available for each
fieldbus.
NTP
(network time protocol) Protocol for synchronizing computer system clocks. The protocol uses a
jitter buffer to resist the effects of variable latency.
O
O->T
(originator to target) See originator and target.
ODVA
(Open DeviceNet Vendors Association) The ODVA supports network technologies that are based
on CIP.
operation network
An Ethernet-based network containing operator tools (SCADA, client PC, printers, batch tools,
EMS, etc.). Controllers are connected directly or through routing of the inter-controller network.
This network is part of the control network.
originator
In EtherNet/IP, a device is considered the originator when it initiates a CIP connection for implicit
or explicit messaging communications or when it initiates a message request for un-connected
explicit messaging.
P
PAC
programmable automation controller. The PAC is the brain of an industrial manufacturing process.
It automates a process as opposed to relay control systems. PACs are computers suited to survive
the harsh conditions of an industrial environment.
port 502
Port 502 of the TCP/IP stack is the well-known port that is reserved for Modbus TCP
communications.
port mirroring
In this mode, data traffic that is related to the source port on a network switch is copied to another
destination port. This allows a connected management tool to monitor and analyze the traffic.
Q
QoS
(quality of service) The practice of assigning different priorities to traffic types for the purpose of
regulating data flow on the network. In an industrial network, QoS is used to provide a predictable
level of network performance.
R
rack optimized connection
Data from multiple I/O modules are consolidated in a single data packet to be presented to the
scanner in an implicit message in an EtherNet/IP network.
ready device
Ethernet ready device that provides additional services to the EtherNet/IP or Modbus module, such
as: single parameter entry, bus editor declaration, system transfer, deterministic scanning
capacity, alert message for modifications, and shared user rights between Unity Pro and the device
DTM.
RIO drop
One of the three types of RIO modules in an Ethernet RIO network. A RIO drop is an M580 rack
of I/O modules that are connected to an Ethernet RIO network and managed by an Ethernet RIO
adapter module. A drop can be a single rack or a main rack with an extended rack.
RIO network
An Ethernet-based network that contains 3 types of RIO devices: a local rack, an RIO drop, and a
ConneXium extended dual-ring switch (DRS). Distributed equipment may also participate in an
RIO network via connection to DRSs or BMENOS0300 network option switch modules.
RPI
(requested packet interval) The time period between cyclic data transmissions requested by the
scanner. EtherNet/IP devices publish data at the rate specified by the RPI assigned to them by the
scanner, and they receive message requests from the scanner at each RPI.
RSTP
(rapid spanning tree protocol) Allows a network design to include spare (redundant) links to provide
automatic backup paths if an active link stops working, without the need for loops or manual
enabling/disabling of backup links.
S
SCADA
(supervisory control and data acquisition) SCADA systems are computer systems that control and
monitor industrial, infrastructure, or facility-based processes (examples: transmitting electricity,
transporting gas and oil in pipelines, and distributing water).
scanner
A scanner acts as the originator of I/O connection requests for implicit messaging in EtherNet/IP,
and message requests for Modbus TCP.
scanner class device
A scanner class device is defined by the ODVA as an EtherNet/IP node capable of originating
exchanges of I/O with other nodes in the network.
service port
A dedicated Ethernet port on the M580 RIO modules. The port may support these major functions
(depending on the module type):
port mirroring: for diagnostic use
access: for connecting HMI/Unity Pro/ConneXview to the CPU
extended: to extend the device network to another subnet
disabled: disables the port, no traffic is forwarded in this mode
SFC
(sequential function chart) Used to graphically represent in a structured manner the operation of a
sequential CPU. This graphical description of the CPU's sequential behavior and of the various
resulting situations is created using simple graphic symbols.
SFP
(small form-factor pluggable). The SFP transceiver acts as an interface between a module and
fiber optic cables.
simple daisy chain loop
Often referred to as SDCL, a simple daisy chain loop contains RIO modules only (no distributed
equipment). This topology consists of a local rack (containing a CPU with Ethernet I/O scanner
service), and one or more RIO drops (each drop containing an RIO adapter module).
SMTP
(simple mail transfer protocol) An email notification service that allows controller-based projects to
report alarms or events. The controller monitors the system and can automatically create an email
message alert with data, alarms, and/or events. Mail recipients can be either local or remote.
SNMP
(simple network management protocol) Protocol used in network management systems to monitor
network-attached devices. The protocol is part of the internet protocol suite (IP) as defined by the
internet engineering task force (IETF), which consists of network management guidelines,
including an application layer protocol, a database schema, and a set of data objects.
SNTP
(simple network time protocol) See NTP.
SOE
(sequence of events) The process of determining the order of events in an industrial system and
correlating those events to a real-time clock.
ST
(structured text) The structured literal language is a developed language similar to computer
programming languages. It can be used to organize a series of instructions.
sub-ring
An Ethernet-based network with a loop attached to the main ring, via a dual-ring switch (DRS) or
BMENOS0300 network option switch module on the main ring. This network contains RIO or
distributed equipment.
subnet mask
The 32-bit value used to hide (or mask) the network portion of the IP address and thereby reveal
the host address of a device on a network using the IP protocol.
switch
A multi-port device used to segment the network and limit the likelihood of collisions. Packets are
filtered or forwarded based upon their source and destination addresses. Switches are capable of
full-duplex operation and provide full network bandwidth to each port. A switch can have different
input/output speeds (for example, 10, 100 or 1000Mbps). Switches are considered OSI layer 2
(data link layer) devices.
T
T->O
(target to originator) See target and originator.
target
In EtherNet/IP, a device is considered the target when it is the recipient of a connection request for
implicit or explicit messaging communications, or when it is the recipient of a message request for
un-connected explicit messaging.
TCP
(transmission control protocol) A key protocol of the internet protocol suite that supports
connection-oriented communications, by establishing the connection necessary to transmit an
ordered sequence of data over the same communication path.
TCP/IP
Also known as internet protocol suite, TCP/IP is a collection of protocols used to conduct
transactions on a network. The suite takes its name from two commonly used protocols:
transmission control protocol and internet protocol. TCP/IP is a connection-oriented protocol that
is used by Modbus TCP and EtherNet/IP for explicit messaging.
TFTP
(trivial file transfer protocol) A simplified version of file transfer protocol (FTP), TFTP uses a client-
server architecture to make connections between two devices. From a TFTP client, individual files
can be uploaded to or downloaded from the server, using the user datagram protocol (UDP) for
transporting data.
TIME_OF_DAY
See TOD.
TOD
(time of day) The TOD type, encoded in BCD in a 32-bit format, contains this information:
the hour encoded in an 8-bit field
the minutes encoded in an 8-bit field
the seconds encoded in an 8-bit field
Example: TOD#23:59:45.
TR
(transparent ready) Web-enabled power distribution equipment, including medium- and low-
voltage switch gear, switchboards, panel boards, motor control centers, and unit substations.
Transparent Ready equipment allows you to access metering and equipment status from any PC
on the network, using a standard web browser.
trap
A trap is an event directed by an SNMP agent that indicates one of these events:
A change has occurred in the status of an agent.
An unauthorized SNMP manager device has attempted to get data from (or change data on) an
SNMP agent.
U
UDP
(user datagram protocol) A transport layer protocol that supports connectionless communications.
Applications running on networked nodes can use UDP to send datagrams to one another. Unlike
TCP, UDP does not include preliminary communication to establish data paths or provide data
ordering and checking. However, by avoiding the overhead required to provide these features,
UDP is faster than TCP. UDP may be the preferred protocol for time-sensitive applications, where
dropped datagrams are preferable to delayed datagrams. UDP is the primary transport for implicit
messaging in EtherNet/IP.
UMAS
(Unified Messaging Application Services) UMAS is a proprietary system protocol that manages
communications between Unity Pro and a controller.
UTC
(coordinated universal time) Primary time standard used to regulate clocks and time worldwide
(close to former GMT time standard).
V
variable
Memory entity of type BOOL, WORD, DWORD, etc., whose contents can be modified by the program
currently running.
VLAN
(virtual local area network) A local area network (LAN) that extends beyond a single LAN to a group
of LAN segments. A VLAN is a logical entity that is created and configured uniquely using
applicable software.
Index
A BMXCRA31210
description, 16, 21
assembly object, 92
external features, 17, 17
AUX0 task, 81
firmware upgrade, 133
AUX1 task, 81
functionality, 17
grounding, 46
hardened, 38
B installation, 42, 46
backplane considerations, 44 Modbus diagnostic codes, 87
BMECRA31210 NTP configuration, 15
description, 16, 21 rack extension, 45
external features, 17 ruggedized, 38
firmware upgrade, 133 specifications, 39
functionality, 17 Unity Pro configuration, 58, 61, 66
grounding, 46 BMXNGD0100
hardened, 38 global data, 28
installation, 42, 46 BMXXBP••••
Modbus diagnostic codes, 87 hardened rack, 38
NTP configuration, 15 ruggedized rack, 38
rack extension, 45
ruggedized, 38
specifications, 39 C
Unity Pro configuration, 58, 61, 66
CANopen modules
BMEXBP••••
X80, 28
hardened rack, 38
CIP objects, 89
ruggedized rack, 38
communication modules
BMXCRA31200
X80, 28
description, 16, 21
connection manager object, 94
firmware upgrade, 133
counting modules
functionality, 17
X80, 28
grounding, 46
hardened, 38
installation, 42, 46 D
Modbus diagnostic codes, 87
device DDT
NTP configuration, 15
RIO adapters, 72
rack extension, 45
T_M_CRA_EXT_IN, 72
ruggedized, 38
diagnostic module
specifications, 39
X80, 28
Unity Pro configuration, 58, 61, 66
diagnostics
Modbus codes, 87
system, 85
E MAST task, 81
mounting a module, 48
ethernet backplane diagnostics object, 126
ethernet link object, 100
Ethernet remote I/O
diagnostics, 83
O
online diagnostics, 130
Unity Pro configuration, 57
Ethernet RIO
cabling, 52
EtherNet/IP
P
explicit messaging, 80 PMESWT0100, 28
implicit messaging, 81 PMXCDA0400, 28
interface diagnostics object, 104 PMXNOW0300, 28
EtherNet/IP explicit connection diagnostics
object, 111, 113
exchange
Q
implicit I/O, 81 QoS object, 95
F R
FAST task, 81 replacing module, 48
fiber cable converter modules rotary switches, 50
X80, 28 RSTP diagnostics object, 115
G S
global data setting rotary switches, 50
BMXNGD0100, 28 SNTP diagnostics object, 122
grounding, 46 specifications
BMECRA31210, 39
BMXCRA31200, 39
I BMXCRA31210, 39
I/O
exchanges, implicit, 81
I/O connection diagnostics object, 107
T
I/O modules, 24 T_M_CRA_EXT_IN, 72
identity object, 90 TCP/IP interface object, 98
implicit I/O exchanges, 81 time stamping, 70
installation, 46 BMXERT1604 module, 70
RIO drop adapters, 70
time stamping modules
M X80, 28
M580
hardened, 38
ruggedized, 38
W
weighing module
X80, 28
wireless module
X80, 28
X
X80
CANopen modules, 28
communication modules, 28
counting modules, 28
diagnostic module, 28
fiber cable converter modules, 28
time stamping modules, 28
weighing module, 28
wireless module, 28
X80 I/O modules, 24
analog, 24
discrete, 24
intelligent, 28
special purpose, 28