Control DA321G5321: List of Parameters
Control DA321G5321: List of Parameters
CONTROL DA321G5321
List of Parameters
- Connection Diagrams
- Timing Diagrams
For current versions of the Instructions for Use and Lists of Parameters, necessary for operating EFKA
drives in accordance with regulations, please refer to the EFKA web site www.efka.net, page
"Downloads".
On our web site you will also find the following supplementary instructions for this control:
General instructions for use and programming
Use with USB Memory Stick
Use of the C200 compiler
Adapter cords
- DA321G5321 -3-
CONTENTS Page
2 Setting and Putting into Service with the Aid of the Fast Installation Routine (SIR) 5
5 List of Parameters 18
5.1 Operator Level 18
5.2 Technician Level 20
5.3 Supplier Level 27
6 Error Displays 57
- DA321G5321 -5-
2 Setting and Putting into Service with the Aid of the Fast Installation
Routine (SIR)
F-200
F-170
Yes
E
No
>>
Setting the reference position
Pos 0
P
P
KL2547
End SIR
The values can be varied by pressing key +/-. When the parameter is
displayed on the V810 control panel, press the E key once more for the
value to be displayed.
-6- List of Parameters
A Power switch
B Display (4 digit 7 segment display)
C Control panel (onboard module)
Key
P Call or exit programming mode
E Start backtack single / double / off
Enter key for modifications in the programming mode
+ End backtack single / double / off
In the programming mode - increase of the value indicated
>> Basic position 1 or 2
In programming mode as shift key
– Automatic sewing foot lifting at stop in the seam On/Off
Automatic sewing foot lifting after thread trimming On/Off
In the programming mode - decrease of the value indicated
The upper vertical segments of the 4 digit 7 -segment display indicate
the switching states of backtacking, foot lifting and basic position.
1 Single start backtack
2 Double start backtack
3 Single end backtack
4 Double end backtack
5 Basic position “needle position 1“
6 Basic position “needle position 2“
7 Automatic sewing foot lifting at stop in the seam
8 Automatic sewing foot lifting after the thread trimming operation
Connector
B20 USB Memory Stick
B22 Socket C knee switch
(C)
Adapter 1113229
LSM...+ HSM...
LSM...+ IPG...
ST2
A A
KL2356a
- DA321G5321 -7-
FF2
FF3
in5
in3
in1 FF2
in4 FF1
in7 FF3
in8 FF1
in2 FF1
in6 FF2
in9
i10
FF3
ATTENTION
When connecting the outputs, ensure that a total power of 96VA constant load will not be
exceeded!
DB3000 Speed limitation bit 3000 min-1 in8 LS Light barrier in9
FA Thread trimmer M1 LSP Machine run blockage in2
FAWU Thread monitor bottom in6 ML Motor running M14
FAWU-L Thread monitor bottom left M7 NFD Sewing foot pressure M17
FAWU-R Thread monitor bottom right M9 NHT Needle up/down in3
FF1 Function module A in4 M6 NK Needle cooling M2
FF2 Function module B in1 M16 R-N-HP Set value potentiometer for speed
limitation depending on high lift
FF3 Function module C in7 M30 R-SELEKT Resistance for machine select
FK Thread clamp M31 VR Backtacking
FL Sewing foot lifting VRU Backtack suppression / recall i10 M8
FSPL Thread tension release M4 ZVR Intermediate Backtack in5
FW Thread wiper M3
HP High lift for walking foot M5
1) Nominal voltage +24 V, no-load voltage max. 30 V momentarily after power on.
Parameters 405 – 408 can be used to switch from 24 V to 30 V.
*) View: Front view of the control (component side) and/or rear view of the outgoing connecting cable
-8- List of Parameters
POS2 OUT Output for position 2 LSM IN Possibility of connecting a light barrier
module to socket B18/8
POS IN Input for positions (e. g. connection of LSM002 Reflection light barrier module
a sensor)
G1/G2 OUT Output of generator impulses HSM001 Hall sensor module
TXD/RXD Serial transmission lines IPG... Pulse encoder
ATTENTION
Before opening the cover, always disconnect the power!
F-550 F-551
BI1179
IN12 Input 12, function programmable using IN13 Input 13, function programmable using
parameter 550 parameter 551
1) Nominal voltage +24 V, no-load voltage max. 30 V momentarily after power on.
Parameters 405 – 408 can be used to switch from 24 V to 30 V.
2) Nominal voltage +5V, Imax 100mA (switchable to +15V, Imax 100mA)
3) Logic level output, specification according to HC74...
*) View: Front view of the control (component side) and/or rear view of the outgoing connecting cable
- DA321G5321 -9-
EB.. = actuator
Pedal step -2 -1 0 ½ 1 2 3 4 5 6 7 8 9 10 11 12
Input A L L H H H L L H H L L H H L L H
Input B L H H L L L H H H H L L L L H H
Input C H H H H L L L L L L L L H H H H
Input D H H H H H H H H L L L L L L L L
4 Timing Diagrams
Trimming from full machine run
1
- 1/2
0
+ -1
-2
n n3 n2 n4 n7 n7
POS.1 0 1 2 3 1 2 3 0 1 2 1 2 3
A/20
POS.2 tFA
A/21
FL t3 c2 c1 t8 t1 c3 t9 c4 t7 t4 t5
A/35
VR
A/34
M1 (FA) iFA
A/37
M4 (FSPL) FSE FSA
A/36
M3 (FW) t6
A/27
M2 (ML)
A/28
0267/FALAUF
1
- 1/2
0
+ -1
-2
n n3 n2 n4 n7 n7
POS.1 0 1 2 3 1 2 3 0 1 2 1 2 3
A/20
POS.2 tFA
A/21
FL t3 c2 c1 t8 t1 c3 t9 c4 t7 t4 t5
A/35
VR
A/34
M1 (FA) iFA
A/37
M4 (FSPL) FSE FSA
A/36
M3 (FW) t6
A/27
M2 (ML)
A/28
0267/FALAUF
1
- 1/ 2
0
-1
+
-2
nrS
n
n6 n3 n2 n1 n2 n4 n7
0 1 2 3 0 1 2
POS.1
SSc
POS.2
FL t3 Arr t1 Err t7 t4 t5
A/35
VR
A/34
STK
A/30
FA iFA
A/37
K-FA (FW)
A/27
NK
A/28
0214/FAKURZ
1
- 1/2
0
+ -1
-2
n n6 n3 n2 n1 n4 n7 n7
POS.1 0 1 2 3 0 1 2 3
A/20
POS.2 SSc tFA
A/21
FL t3 c1 t1 t3 c3 t7
A/35
VR
A/34
M1 (FA) iFA
A/37
M4 (FSPL) FSE FSA
A/36
M3 (FW) t6
A/27
M2 (ML)
A/28
0267/FAZW
1
- 1/2
0
+ -1
-2
n n2 n5 n4 n7 n7
POS.1 0 3 4 5 61 2 3
A/20
POS.2 tFA
A/21
FL t3 LS c3 t7 t4 t5
A/35
VR
A/34
M1 (FA) iFA
A/37
M4 (FSPL) FSE FSA
A/36
M3 (FW) t6
A/27
M2 (ML)
A/28
LS
0267/ENDELS
1
- 1/2
0
+ -1
-2
n n12 n4 n7 n7
POS.1 0 10 20 22 1 2 3 1 2 3
A/20
POS.2 tFA
A/21
FL t3 Stc c3 c4 t7 t4 t5
A/35
VR
A/34
M1 (FA) iFA
A/37
0267/ENDEZAE
1
- 1/2
0
+ -1
-2
n n3 n1 n3 n1 n3 n2 n1 n4 n1 n4 n7 n7
POS.1 0 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3
A/20
POS.2
A/21
FL t3 SAv tSr SAr tSr SAr t1 tSr SEr tSr SEv tFA
A/35
VR
A/34
M1 (FA) iFA
A/37
M4 (FSPL) FSE FSA
A/36
M3 (FW) t6
A/27
M2 (ML)
A/28
0267/LAUFZVR
1
- 1/2
0
+ -1
-2
n n3 n2 n10 n2 n4 n7 n7
POS.1 0 1 2 3 1 2 3 0 1 2 3 4 5 6 0 1 2 1 2 3
A/20
POS.2 tFA
A/21
FL t3 t1 cb tHP t7
A/35
VR c2 c1 c3 c4
A/34
M1 (FA) iFA
A/37
M4 (FSPL) FSE FSA
A/36
M3 (FW) t6
A/27
M2 (ML)
A/28
M5 (HP)
A/32
M11 (LHP)
A/31
HP
A/7
0267/LAUFHUB
5 List of Parameters
5.1 Operator Level
parameter Designation Unit Limits Preset for Ind.
max min 100Ω 220Ω 680Ω 1000Ω
000 c2 Number of stitches of start backtack Stitches 254 0 2 3 2 2 A
forward
001 c1 Number of stitches of start backtack Stitches 254 0 4 3 2 4 A
backward
002 c3 Number of stitches of end backtack Stitches 254 0 3 2 2 3 A
backward
003 c4 Number of stitches of end backtack Stitches 254 0 3 3 5 3 A
forward
004 LS Light barrier compensating stitches Stitches 254 0 4 4 4 4 A
(for long stitch length)
005 LSF Number of stitches of the light barrier filter Stitches 254 0 0 0 0 0 A
for knitted fabrics
006 LSn Number of light barrier seams 15 1 1 1 1 1 A
007 Stc Number of stitches for the seam with Stitches 254 0 10 10 10 10 A
stitch counting
008 -F- A parameter from the technician level is 5 1 2 2 2 2 A
assigned to key 9 on the V820/V850
control panel
1 = Softstart On/Off
2 = Ornamental backtack On/Off
3 = High lift for walking foot (only if
parameter 250 or 255 = 11) latching
= ON / push = OFF
4 = Needle cooling ON/OFF (only if
parameter 185 = 1)
5 = Signal A1 and/or A2 On/Off with
slide-in strip 1...4 (left-hand arrow =
A1, right-hand arrow = A2)
009 LS Light barrier On/Off 1 0 0 0 0 0 A
010 cLS Light barrier compensation stitches (for Stitches 254 0 8 8 8 8 A
long stitch length)
013 FA Thread trimmer On/Off 1 0 0 0 0 0 H
014 FW Thread wiper On/Off 1 0 0 0 0 0 A
015 StS Stitch counting On/Off 1 0 0 0 0 0 A
023 AFL Automatic sewing foot lifting with pedal 1 0 0 0 0 0 A
forward at the seam end, if light barrier or
stitch counting is On
0 = Automatic sewing foot Off
1 = Automatic sewing foot On
024 FLS Sewing foot lifting function for standing 3 0 0 0 0 0 0 F
operation
0 = Function Off
1 = Function on only in the seam
2 = Function on only at seam end
3 = Function on in the seam and at the
seam end
026 APd Characteristic of the "analog pedal" 5 0 4 4 4 4 4 L
0 = Analog function off
1 = 12-level, like previous pedal function
2 = continuously variable
3 = 24-level
4 = 60-level (progressive)
5 = 60-level (progressive)
060 3Er Triple end backtack Stitches 254 0 0 0 0 0 H
0 = Function OFF, only doubled backtack
possible
1...254 =Function ON, value = number of
stitches in the third backtack
segment
080 SAv Number of stitches for initial ornamental Stitches 254 0 3 3 2 3 A
backtack forwards
081 SAr Number of stitches for initial ornamental Stitches 254 0 3 3 2 3 A
backtack backwards
082 SEr Number of stitches for final ornamental Stitches 254 0 3 3 2 3 A
backtack backwards
- DA321G5321 - 19 -
***) The 4-digit value displayed on the controller must be multiplied by 10.
- 20 - List of Parameters
Technician Level (Code 190 when operating at the controller or 1907 when operating at the control panel)
Technician Level (Code 190 when operating at the controller or 1907 when operating at the control panel)
Technician Level (Code 190 when operating at the controller or 1907 when operating at the control panel)
Technician Level(Code 190 when operating at the controller or 1907 when operating at the control panel)
Technician Level (Code 190 when operating at the controller or 1907 when operating at the control panel)
2740 10 11 19
Technician Level (Code 190 when operating at the controller or 1907 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
360°
SEN
+5V
POS
IN 0V
B18/7
= 0V = high 0256/SEN-1a
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
360°
SEN
+5V
POS
IN 0V
B18/7
POS2
270 = 4 270 = 3 270 = 2 270 = 1
ST2/21
OUT
POS1 Pa 171
ST2
ST2/20
POS2
ST2/21
OUT
POS1 Pa 171
ST2/20
POS1
ST2/20
OUT
POS2 Pa 171
ST2/21
POS1
ST2/20
OUT
POS2 Pa 171
ST2/21
= 0V = high 0256/SEN-2a
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset
parameter 100R 220R 470R 680R 1000R parameter 100R 220R 470R 680R 1000R
290 0 0 0 0 0 290 0 0 0 0 0
Select- and machine-dependent preset value (mode can be set with parameter 290)
N291-164162
N291-185182
271, 272,
8967
Preset
Parameter 100R
290 0 0 1 2
013 0 = 1 1
014 0 = 1 1
110 180 = 150 150
111 1000 = 4000 3000
112 1700 = 1200 1200
113 1700 = 1200 1200
114 1700 = 1200 1200
115 800 = = 500
116 180 = 150 150
117 2000 = = 1500
123 0 = 40 40
124 1700 = 500 500
154 2 = 0 0
170 Reference
point POS1 = D D
171 P1E 355 = 119 294
P2E 262 = 308 130
P1A 70 = 175 329
P2A 338 = 357 163
180 14 = 28 20
181 0 = = 20
182 0 = = 1
186 0 = 10 10
190 280 = 126 126
207 20 = = =
208 30 = = =
219 10 = = =
220 20 = = =
255 0 = = 11
270 0 = 6 6
272 1000 = = 800
275 0 = = 17
204-370
205-370
204-102
Preset
221
Parameter 220R
290 0 1 2 3 4
013 0 1 1 1 1
014 0 1 1 1 1
110 150 = = = 200
111 1000 800 800 650 =
112 400 = = = =
113 400 = = = =
114 400 = = = =
115 250 = = = =
116 100 = = 150 150
117 400 = = = =
118 400 = = = =
123 0 = = = =
124 800 = = = =
153 6 = = = =
170 Reference
point EP = = = =
171 P1E 105 = = = 128
P2E 252 = = = 305
P1A 170 = = = 170
P2A 320 = = = 355
180 28 = = = =
190 315 = = = =
207 20 5 5 5 5
208 30 10 10 10 10
210 270 = = = =
219 10 2 2 2 4
220 20 2 2 2 5
221 100 = = = 100
222 120 = = = =
223 1600 200 200 200 200
224 1 = = = =
242 2 1 1 1 1
270 6 = = = =
272 1000 250 250 373 439
195-171110
195-171521
195-671110
Preset
Parameter 470R
290 0 1 2 3
000 0 = = =
001 5 = = =
002 5 = = =
003 0 = = =
008 1 = = =
013 0 1 1 1
014 0 = = =
110 150 = = =
111 1000 4000 4000 4000
112 1500 = = =
113 1500 = = =
114 3000 = = =
115 800 = = =
116 150 180 180 180
136 0 1 1 1
170 Reference
point EP = = =
171 P1E 141 = = =
P2E 260 = = =
P1A 170 = = =
P2A 290 = = =
206 0 = = =
250 0 = = =
251 0 = = =
252 0 = = =
253 0 = = =
254 0 = = =
255 0 = = =
256 0 = = =
257 0 = = =
258 0 = = =
259 0 = = =
260 0 = = =
261 2 = = =
270 0 6 6 6
272 1000 1052 1052 1052
362 0 = 80 =
363 200 = 120 =
364 0 = = =
365 550 = 300 =
366 2 = = =
367 0 = = =
368 1 = = =
369 0 = = =
4280 (1:1,4)
838 (1:1,5)
4180 (1:1)
888 (1:1,5)
888 (1:1)
Preset
267
269
667
69
Parameter 680R
290 0 1 2 3 4 5 10 11 12 13
000 2 = = 1 1 1 = = = =
001 2 3 3 = = = = = = =
002 2 = = = = = = = = =
003 5 2 2 3 3 3 = = = =
013 0 = 1 1 1 1 = = = =
014 0 = = = = = = = = =
080 2 = = 3 3 3 = = = =
081 2 = = 3 3 3 = = = =
082 2 = = 3 3 3 = = = =
110 150 = = = = = 200 150 150 150
111 1700 = = = = = = = = 1500
112 800 = = = = = = = = =
113 800 = = = = = = = = =
114 800 = = = = = = = = =
115 400 = = = = = = = = =
116 150 180 180 180 180 180 = = = =
117 800 = = = = = = = = =
123 0 = = = = = = = = =
124 800 = = = = = = = = =
153 6 = = = = = = = = =
170 Reference
point EP = = = = = = = = =
171 P1E 25 = = 115 115 115 120 120 120 110
P2E 315 = = = = 325 315 315 315 315
P1A 85 = = 175 175 175 170 180 180 165
P2A 15 = = = = = 15 15 15 15
180 20 = = = = 30 = = = =
182 0 = = 1 1 1 = = = =
190 315 = = 130 130 130 = = = =
191 50 = = = = = = = = =
192 237 = = 130 130 110 = = = =
193 0 = = = = = = = = =
194 0 = = = = = = = = =
196 0 = = 2 2 2 = = = =
203 200 = = 350 350 350 = = = =
207 20 = = = = = 10 10 10 5
208 30 = = = = = 15 15 15 10
210 150 = = = = = = = =
219 10 = = = = = 4 5 5 3
220 20 = = = = = 20 20 20 10
221 100 = = = = = = = = =
222 120 20 20 20 20 20 20 20 20 20
223 1600 = = = = = 200 200 1000 1000
224 1 = = = = = 1 1 0 0
241 9 = = 8 8 8 = = = =
242 2 = = 1 1 1 = = = =
250 1 = = 16 16 4 = = = =
269 15 = = = = = = = = =
270 0 = 6 = 6 6 6 6 6 6
272 1000 = 722 = 642 642 533 533 536 710
297 180 = = 60 60 60 = = = =
768-FA-R373 RAP-HP,
767-FAS 373-RAP-HP,
767-FAS 573-RAP-HP,
767-KFA 373-RAP-HP
768-FA-L373 RAP-HP
768-FA-273 RAP-HP
768-R374 FLP-HP
768-274 FLP-HP,
467-65-FA-273,
467-65-FA-373
767-VF-373,
767-FA-273
467-183081
367-170315
367-170115
767-AE-73,
767-LG-73
381, 382
Preset
1000R
290 0 0 1 2 3 4 5 6 7 8 9 10
013 0 = 1 1 1 1 1 1 1 1 1 1
014 0 = = = = = = = = = = =
111 1000 = 3200 3200 3000 2800 2400 2400 2400 3200 3000 2500
112 1200 = = = = = = = 800 = = =
113 1200 = = = = = = = 800 = = =
114 1200 = = = = = = = 800 = = =
117 2000 = = = = = = 1600 1600 1800 1800 =
123 40 = = = = = = = = 50 50 =
124 500 = = = = = = = 400 400 400 =
136 0 = = 2 = = = = 2 2 1 =
153 6 = = = = = = = = 20 20 =
154 0 = = 7 = = = = = = = =
170 Reference
point EP = = = = = = = = = = =
171 P1E 42 = = = = = = = 37 21 21 102
P2E 326 = = 347 = = = 252 = = = 322
P1A 140 = = = = = = = = = = =
P2A 357 = = 24 = = = 3 = 3 3 =
180 63 = = 70 = = = = 42 42 42 =
181 0 = = 10 = = = = = = = =
182 0 = = 1 = = = = 1 1 1 =
186 0 = = = = = = = = 10 10 =
189 1 = = = = = = = = = = =
190 56 = = 210 = = = = 119 161 161 210
191 50 = = = = = = = = = = 100
192 182 = = 217 = = = = 140 231 231 70
193 30 = = = = = = = 0 = = =
194 0 = = = = = = = = 105 105 =
196 0 = 0 0 2 2 = 2 2 2 2 =
197 0 = = = = = = 1 1 1 = =
207 20 = = = = = = = = = = 10
208 30 = = = = = = = = = = 15
210 100 = = = = = = = 200 = = =
219 10 = = = = = = = = = = 10
241 9 = = = = = = = = = = =
242 2 = = = = = = 1 1 = = =
261 1 = = = = = = 3 3 = = =
269 40 = 15 15 15 15 15 15 15 15 15 =
270 0 = 6 6 6 6 6 6 6 6 6 6
272 1000 = 880 880 880 880 663 558 558 800 800 704
275 17 = = = = = = = = = = 5
288 1200 = = = = = = = 2400 = = =
297 180 = 0 0 = = = = = = = =
327-170115
367-180115
367-170010
367-180010
561-180242
561-180142
Preset
1000R
290 0 11 12 13 13
013 0 1 1 1 1
111 1000 3500 2800 3000 3000
112 1200 = = = =
113 1200 = = = =
114 1200 = = = =
117 2000 1800 1800 1400 1800
123 40 50 50 = =
124 500 400 400 = =
136 0 1 1 = =
153 6 20 20 25 25
154 0 = = = =
162 100 = = = =
163 100 = = = =
170 Reference
point EP = = = =
171 P1E 42 21 21 16 16
P2E 326 = = = =
P1A 140 = = = =
P2A 357 3 3 = =
180 63 42 42 55 45
181 0 = = = =
182 0 1 1 1 1
186 0 10 10 = =
189 1 = = 0 0
190 56 161 161 240 240
191 50 = = = =
192 182 231 231 231 231
193 30 = = 0 0
194 0 105 105 = =
196 0 2 1 2 2
197 0 = = = =
201 80
210 100 = = = =
223 1600 1000 1000 = =
241
(for machines with 9 = = 8 8
tilt sensor)
241
(for machines 9 = = 0 0
without tilt sensor)
242 2 = = 1 1
255 7 = = = =
261 1 = = = =
269 40 15 15 15 15
270 0 6 6 = =
272 1000 900 800 = =
288 1200 = = = =
333 0 = = = =
334 85 = = = =
550 13 = = = =
551 14 = = = =
867-180445 KFA-AUT
867-190146 (NSB)
7252x i Minerva
867-190040-70
867-190342-70
867-190322
867-190342
867-190020
867-190040
Preset
1000R
290 0 19 20 21 22 23 24 25 26
013 0 1 1 1 1 1 1 1 1
100 1 = = = 2 = = = =
111 1000 3500 3400 3400 3400 3400 3000 3000 3000
112 1200 = = = = = = = =
113 1200 = = = = = = = =
114 1200 = = = = = = = =
115 400 = = = 250 = = = =
116 150 = = = 140 = = = =
117 2000 = 1800 1800 1800 1800 = = 1800
123 40 = = = = = = = =
124 500 = = = = = = = =
136 0 = = = 2 2 = = =
153 6 = 25 25 25 25 = = 25
154 0 = = = 8 8 = = =
162 100 = = = = = = = =
163 100 = = = 50 50 = = =
170 Reference
point EP = = = = = = =
171 P1E 42 110 16 16 16 = = 16
P2E 326 315 = = = 268 268 =
P1A 140 170 = = = = = =
P2A 357 60 = = = = = =
180 63 40 45 45 45 45 = = 45
181 0 = = = 20 = = = =
182 0 1 1 1 1 1 = = 1
186 0 = = = = = = = =
189 1 = 0 0 0 0 = = 0
190 56 170 240 240 240 240 = = 240
191 50 = = = = = = = =
192 182 160 231 231 260 260 = = 231
193 30 = 0 0 0 0 = = 0
194 0 = = = = = = = =
196 0 = 2 2 2 2 = = 2
197 0 = = = = = = = =
201 80 120 = = = = = = =
210 100 = = = = = = = =
223 1600 = 1200 1200 = = = = =
867-180445 KFA-AUT
867-190146 (NSB)
7252x i Minerva
867-190040-70
867-190342-70
867-190322
867-190342
867-190020
867-190040
Preset
1000R
290 0 19 20 21 22 23 24 25 26
241
(for machines with 9 = 8 8 8 = = 8
tilt sensor)
241
(for machines 9 = 0 0 0 0 0 0
without tilt sensor)
242 2 1 1 1 1 = = 1
255 7 = = = = = = =
261 1 = = = = = = =
269 40 = 15 15 = = = =
270 0 6 = = = = = =
272 1000 1063 = = = = = =
288 1200 = = = = = = =
333 0 = = = = = = =
334 85 = = = 35 = = =
550 13 = = = = = = =
551 14 = = = 35 = = =
- DA321G5321 - 45 -
867-180445 KFA-AUT
867-190040-70
867-190342-70
867-190020
867-190040
867-190322
867-190342
Preset
1000R
290 0 30 31 32 34 35 36
868-190020
868-290020
868-190322
868-290322
868-390322
868-190341
868-290341
868-490322
869-180122
869-280122
869-180322
869-280322
669-180010
869-180020
869-280020
669-180112
869-180122
869-280122
669-180312
869-180322
869-280322
Preset
1000R
290 0 40 41 42 43 45 46 47 48 49
013 0 = 1 1 1 1 1 = 1 1
111 1000 2500 2500 2500 2500 2800 2800 2800 3000 3000
117 2000 = 1600 1600 1600 1800 1800 = 1800 1800
123 40 = = = = = = = = =
124 500 = = = = = = = = =
136 0 = 2 2 2 2 2 = = =
153 6 = 25 25 25 19 19 15 19 19
154 0 = = = = = = 8 = =
162 100 = = = = = = = = =
163 100 = = = = = = 50 = =
170 Reference
point EP = = = = = = = = =
171 P1E 42 = 16 16 16 16 16 = 16 16
P2E 326 268 = = = = = 268 = =
P1A 140 = = = = = = = = =
P2A 357 = = = = = = = = =
180 63 = 45 45 15 45 45 = 45 45
182 0 = 1 1 1 1 1 = 1 1
189 1 = 0 0 0 0 0 = 0 0
190 56 = 240 240 240 240 240 = 240 240
191 50 = = = = = = = = =
192 182 = 231 231 231 231 231 = 231 231
193 30 = 0 0 0 0 0 = 0 0
196 0 = 2 2 2 2 2 = 2 2
197 0 = = = = = = = = =
241 9 = 8 8 8 8 8 = 8 8
242 2 = 1 1 1 1 1 = 1 1
255 7 = = = = = = = = =
270 0 6 6 6 6 6 6 6 6 6
272 1000 100 642 642 642 703 703 703 703 703
289 3000 = 1600 1600 1500 = = = = =
550 13 = = = = = = = = =
551 14 = = = = = = = = =
867-280445 KFA-AUT
867-290342-100
867-290040-70
867-290342-70
867-290020
867-290040
867-290322
867-290342
867-490322
Preset
1000R
290 0 50 51 52 53 54 55 56 57
111 1000 3000 3000 3000 2500 3000 3000 3000 2500
117 2000 = 1800 1800 1800 1800 = 1800 1800
123 40 = = = = = = = =
124 500 = = = = = = = =
136 0 = 2 2 2 2 = 2 2
153 6 = 25 25 25 25 = 25 25
154 0 = = = = 8 = = =
162 100 = = = = = = = =
163 100 = = = = 50 = = =
170 Reference
point EP = = = = = = = =
171 P1E 42 = 16 16 16 16 = 16 16
P2E 326 268 = = = = 268 = =
P1A 140 = = = = = = = =
P2A 357 = = = = = = = =
180 63 = 45 45 15 45 = 45 45
182 0 = 1 1 1 1 = 1 1
189 1 = 0 0 0 0 = 0 0
190 56 = 240 240 240 240 = 240 240
191 50 = = = = = = = =
192 182 = 231 231 231 260 = 231 231
193 30 = 0 0 0 0 = 0 0
196 0 = 2 2 2 2 = 2 2
197 0 = = = = = = = =
241 9 = 8 8 8 8 = 8 8
242 2 = 1 1 1 1 = 1 1
255 7 = = = = = = = =
270 0 6 6 6 6 6 6 6 6
272 1000 642 642 642 642 642 642 642 642
333 0 = = = = = = = =
334 85 = = = = 35 = = =
550 13 = = = = = = = =
551 14 = = = = = = = =
867-280445 KFA-AUT
867-394342 AE
867-392342 LG
867-393342 VF
867-290040-70
867-290342-70
(AE=LG+VF)
867-290020
867-290040
867-290322
867-290342
Preset
1000R
290 0 60 61 62 64 65 66 70 71
111 1000 3000 3000 3000 3000 3000 3000 3000 3000
117 2000 = 1800 1800 1800 = 1800 1800 1800
123 40 = = = = = = = =
124 500 = = = = = = = =
136 0 = 2 2 2 = 2 2 2
153 6 = 25 25 25 = 25 25 25
154 0 = = = 8 = = = =
162 100 = = = = = = = =
163 100 = = = 50 = = = =
170 Reference
point EP = = = = = = = =
171 P1E 42 = 16 16 16 = 16 16 16
P2E 326 268 = = = 268 = = =
P1A 140 = = = = = = = =
P2A 357 = = = = = = = =
180 63 = 45 45 45 = 45 45 45
182 0 = 1 1 1 = 1 1 1
189 1 = 0 0 0 = 0 0 0
190 56 = 240 240 240 = 240 240 240
191 50 = = = = = = = =
192 182 = 231 231 260 = 231 231 231
193 30 = 0 0 0 = 0 0 0
196 0 = 2 2 2 = 2 2 2
197 0 = = = = = = = =
241 9 = 8 8 8 = 8 8 8
242 2 = 1 1 1 = 1 1 1
255 7 = = = = = =
267 0 = 2
270 0 6 6 6 6 6 6 6 6
272 1000 724 724 724 724 724 724 642 642
333 0 = = = = = =
334 85 = = = 35 = =
550 13 = = = = = = = =
551 14 = = = = = = = =
767-FAS 373-RAP-HP,
767-FAS 573-RAP-HP,
767-KFA 373-RAP-HP
467-65-FA-273,
467-65-FA-373
767-VF-373,
767-FA-273
467-183081
767-AE-73,
767-LG-73
Preset
4700R
290 0 0 1 2 3 4 5
013 0 = 1 1 1 1 1
014 0 = = = = = =
111 1000 = 3200 3200 3000 2800 2400
112 1200 = = = = = =
113 1200 = = = = = =
114 1200 = = = = = =
117 2000 = = = = = =
123 40 = = = = = =
124 500 = = = = = =
136 0 = = 2 = = =
153 6 = = = = = =
154 0 = = 7 = = =
170 Reference
point EP = = = = = =
171 P1E 42 = = = = = =
P2E 326 = = 347 = = =
P1A 140 = = = = = =
P2A 357 = = 24 = = =
180 63 = = 70 = = =
181 0 = = 10 = = =
182 0 = = 1 = = =
186 0 = = = = = =
189 1 = = = = = =
190 56 = = 210 = = =
191 50 = = = = = =
192 182 = = 217 = = =
193 30 = = = = = =
194 0 = = = = = =
196 0 = 0 0 2 2 =
197 0 = = = = = =
207 20 = = = = = =
208 30 = = = = = =
210 100 = = = = = =
219 10 = = = = = =
241 9 = = = = = =
242 2 = = = = = =
261 1 = = = = = =
269 40 = 15 15 15 15 15
270 0 = 6 6 6 6 6
272 1000 = 880 880 880 880 663
275 17 = = = = = =
288 1200 = = = = = =
297 180 = 0 0 = = =
501 112 = = = = = =
502 55 = = = = = =
503 1 = = = = = =
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
0= Suppression Off
1= Suppression On
322 dkn 0 = Correction seam Off 3 0 0 0 0 0 L
1= Correction seam On
2= Interruption of seam or pattern by
thread trimmer
3 = Seam end in plug program execution
- 52 - List of Parameters
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Parameter
0 1 0 0 0 0 0
100
0 1 1 100 0 0 0
10
0 1 2 0 0 10 0
100
1 1 0 0 100 0 0
100 100
1 1 1 100 100 0 0
10
3 1 0 0 0 0 10
10 10
3 1 2 0 0 10 10
100 10
3 1 1 100 0 0 10
10 100
1 1 2 0 100 10 0
100
1 2 0 0 100 0 0
100 100
1 2 1 100 100 0 0
0256/BILD4
NA = Start of seam
LS = Light barrier bright or dark on seam end
LS-D = Light barrier uncovered covered (parameter 131 = 1 and parameter 132 = 0)
NE = Seam end
FA-E = End thread trimming operation
P=0 = Pedal in pos. 0 (neutral)
St = Stitches
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Parameter
0 0 0 0 0 0 0 1)
0 0 0 0 0 0 0 2)
100
1 0 0 0 100 0 0
100 100
1 0 1 100 100 0 0
10
3 0 0 0 0 0 10
10 10
3 0 2 0 0 10 10
100 10
3 0 1 100 0 0 10
10 100
1 0 2 0 100 10 0
2 0 0 0 0 0 0 1)
2 0 0 0 0 0 0 2)
100
0 0 1 100 0 0 0
10
0 0 2 0 0 10 0
100
1 3 0 0 100 0 0
100 100
1 3 1 100 100 0 0
10
3 3 0 0 0 0 10
10 10
3 3 2 0 0 10 10
100 10
3 3 1 100 0 0 10
10 100
1 3 2 0 100 10 0
2 3 0 0 0 0 0
0 3 0 0 0 0 0
100
0 3 1 100 0 0 0
10
0 3 2 0 0 10 0
100
2 3 1 100 0 0 0
10
2 3 2 0 0 10 0
0256/BILD3
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
Supplier level (Code 311 when operating at the controller or 3112 when operating at the control panel)
6 Error Displays
On the On the V810 On the Signification
control V820/V850
General Information
A1 InF A1 InF A1 Pedal not in neutral position when turning the machine
on
A2 -StoP- blinking -StoP- blinking + Machine run blockage
symbol display
A3 InF A3 InF A3 Reference position is not set
A4 InF A4 Power OFF/ON Machine select of parameter 280 taken over
A5 InF A5 InF A5 Emergency run, identification of an invalid machine
select
A6 InF A6 InF A6 Light barrier monitoring
A7 Symbol blinking Symbol blinking Bobbin thread monitor
A8 InF A8 InF A8 No stepping motor control connected
A500 FileFl File Full Max. number of files (99) on Memory Stick exceeded
A501 noFile noFile File not found on Memory Stick
A503 not EQ not EQ Data on Memory Stick and in the control is not equal
Serious Condition
E1 InF E1 InF E1 The external pulse encoder e.g. IPG... is defective or
not connected
E2 InF E2 InF E2 Line voltage too low, or time between power Off and
power On too short
E3 InF E3 InF E3 Machine blocked or does not reach the desired speed
E4 InF E4 InF E4 Control disturbed by deficient grounding or loose
contact
E7 InF E7 InF E7 24 V power supply unit overload
E8 InF E8 InF E8 Too much data for the EEPROM or flash memory
E9 InF E9 InF E9 EEPROM or flash memory defective
E10 InF E10 InF E10 Short-circuit on output
(output FL, VR, M1, M2, M3, M4 or M10)
E11 InF E11 InF E11 Thermal overload of output stage transistor
E12 InF E12: 003 InF E12: 003 Short-circuit on output M5
E12 InF E12: 004 InF E12: 004 Short-circuit on output M9
E12 InF E12: 005 InF E12: 005 Short-circuit on output M11
E12 InF E12: 006 InF E12: 006 Short-circuit on output M7
E12 InF E12: 008 InF E12: 008 Short-circuit on output M8
E12 InF E12: 009 InF E12: 009 Short-circuit on output M6
Hardware Disturbance
H1 InF H1 InF H1 Commutation transmitter cord or frequency converter
disturbed
H2 InF H2 InF H2 Processor disturbed
Free Programming
U1 InF U1 InF U1 Compiler, invalid code, unknown command
U2 InF U2 InF U2 Invalid system function
U3 InF U3 InF U3 Invalid input/output number
U4 InF U4 InF U4 Too many user variables
U5 InF U5 InF U5 Too many system variables
U6 InF U6 InF U6 User program too large for memory
U7 InF U7 InF U7 Invalid or undefined key in Variocontrol
U8 InF U8 InF U8 Unknown device address
U9 InF U9 InF U9 Fatal exception error
- DA321G5321 - 59 -
OF AMERICA INC.
3715 NORTHCREST ROAD – SUITE 10 – ATLANTA – GEORGIA 30340
PHONE: +1-770-457 7006 – FAX: +1-770-458 3899 – email: [email protected]