DDC SVC Bro 0001 PDF
DDC SVC Bro 0001 PDF
DDC SVC Bro 0001 PDF
Trademark Information
DDC®, Detroit Diesel®, and the spinning arrows design are registered trademarks of Detroit
Diesel Corporation. Series 50®, Series 55®, Series 60®, DD13™, DD15™, DD16™, and
POWER GUARD® are registered trademarks of Detroit Diesel Corporation. Fuel Pro®, Sea
Pro®, and Mega Filter® are registered trademarks of Davco Manufacturing, LLC. All other
trademarks are the property of their respective owners.
TABLE OF CONTENTS
1 INTRODUCTION ................................................................................................................. 1- 1
6 FILTRATION ........................................................................................................................ 6- 1
6.1 FUEL AND LUBRICATING OIL FILTERS ....................................................................... 6- 1
6.2 SUPPLEMENTAL OIL FILTERS ..................................................................................... 6- 2
6.3 BOSCH/DELPHI FUEL FILTRATION SYSTEMS ............................................................ 6- 5
6.4 AFTERMARKET FILTRATION SYSTEMS ...................................................................... 6- 5
6.5 DETROIT DIESEL GENUINE MAINTENANCE PRODUCTS ......................................... 6- 6
1 INTRODUCTION
This publication specifies the type of lubricants, fuels, filters, and related maintenance intervals
required for the diesel-fueled engines manufactured and marketed by Detroit Diesel®. The
information in this publication applies to Series 60, Series 50, Series 55, Series 40, MBE 900,
MBE 4000, DD13, DD15, and DD16 engines.
Information on the use of diesel exhaust fluid (DEF) is located in EPA10 DD Platform Operators
Manual (DDC-SVC-MAN-0075). Coolant references are located in Coolant Requirements For
Engine Cooling Systems,(DDC-SVC-BRO-0002).
NOTE:
For 2-cycle and all Off-Highway engine lubricating oil, fuel, and coolant requirements,
refer to MTU Technical Publication, Fluids and Lubricants, Specification Bulletin,
A001061/33E (or most recent). This bulletin is available from authorized MTU
distributors.
For information on fuels, lubricants, and filters required for Detroit Diesel engines using alternate
fuels (other than diesel fuel) and other engine products not covered in this publication, refer
to the specific publications for those engines.
Selection of the proper quality of fuel, lubricating oil, and filters in conjunction with required
oil and filter maintenance is required to achieve the long and trouble-free service which Detroit
Diesel engines are designed to provide. Operation with improper fuels, lubricants, and filters can
degrade engine performance and may void the manufacturer’s warranty.
In general, lubricating oil selection for Detroit Diesel engines is based on viscosity grade and
service category as defined by industry standards and is displayed in the API symbol shown in the
following section. Oils identified by this system and licensed by API provide adequate service
in most applications. In 2002, Detroit Diesel initiated additional criteria to these requirements
through the use of POWER GUARD® Oil Specifications (PGOS) which resulted in a listing
of preferred oils for Detroit Diesel engines.
NOTE:
For 2-cycle and all Off-Highway engine lubricating oil, fuel, and coolant requirements,
refer to MTU Technical Publication, Fluids and Lubricants, Specification Bulletin,
A001061/33E (or most recent). This bulletin is available from authorized MTU
distributors.
Selection of lubricating oil that meets the proper criteria is necessary for proper engine lubrication.
Additional information which may be used to select an appropriate engine oil are provided in
the following sections.
The viscosity requirements associated with each SAE viscosity grade are listed in Table 3-1.
This information is important in selecting the best viscosity grade for the anticipated ambient
temperature range at which the engine will start and operate. Use it only as a guideline, since
actual operating conditions of the engine may determine the lowest practical temperature at which
an engine will start and operate. Note that grades designated with a “W” are required to meet both
low temperature and high temperature viscosity requirements.
Table 3-1 SAE Viscosity Grades for Engine Oils (SAE J300)
For standard temperature limits of each viscosity grade; see Figure 3-1.
15W-40 15W-40
10W-30
Viscosity Grade API Service CH-4, CI-4 PLUS CJ-4
CJ-4
PGOS 93K214 / 215 PGOS 93K218
Viscosity, Kinematic, cSt: 40°C 95 – 115 95 – 115 75 – 85
Viscosity, Kinematic, cSt: 100°C 12.5 – 16.3 12.5 – 16.3 9.3 – 12.5
HT/HS, cP 150°C 3.7 Min 3.7 Min 3.5 Min
Viscosity Index 130 130 130
Pour Point °C, Max -23 -23 -30
Flash Point °C, Min 215 215 205
Sulfated Ash,
2.0 Max 1.0 Max 1.0 Max
% Mass
Total Base Number 9.0 – 11.0 8.0 – 10.0 8.0 – 10.0
Sulfur, ppm 4000 – 8000 4000 Max 4000 Max
Phosphorous, ppm 1000 – 1200 1000 – 1200 1000 – 1200
Zinc, ppm 1000 – 1200 1000 – 1200 1000 – 1200
Detroit Diesel favors the recycling of waste oil and permits the use of rerefined oils in all
engine product lines, provided the rerefined oil meets the SAE Viscosity and API specifications
previously mentioned. Several processes are used to rerefine oil. The only true rerefining process
is one which treats the used oil as a crude oil, subjecting it to the same refinery processes normally
used for geological crude, such as dehydration, vacuum distillation, and hydrogenation. Waste oil
provides a more consistent feedstock, compared to the geological crudes that a refinery typically
processes. As a result, the finished oil should also be consistent in properties and quality.
During use, engine lubricating oil undergoes deterioration from combustion by-products and
contamination by the engine. In addition, certain components in a lubricant additive package are
designed to deplete with use. For these reasons, regardless of the oil formulation, regular oil
drain intervals are required.
NOTE:
The use of oil sampling and analysis to validate all drain intervals is highly recommended.
To confirm oil drain intervals, use Detroit Diesel Genuine Oil Analysis with Total Base
Number, Part Number 23520989.
Service Application
Long Haul * Short Haul † Severe ‡
Engine Series
20,000 15,000 miles
30,000 miles
Series 60, EPA07 (32,000 km) (24,000 km)
(48,000 km)
500 h, or 6 mon§ 300 h, or 3 mon§
15,000 miles 10,000 miles
30,000 miles
MBE 4000, EPA07 (24,000 km), (16,000 km)
(48,000 km)
500 h, or 6 mon§ 300 h, or 3 mon§
50,000 miles 35,000 25,000 miles
DD13, DD15, DD16
(80,000 km) (56,000 km) (40,000 km)
EPA07, EPA10
1280 h 895 h, or 1 yr§ 640 h, or 6 mon§
* Long Haul (over-the-road transport) service applies to vehicles that annually travel more than 60,000 miles
(96,000 kilometers) and average greater than 6 miles per gallon with minimal city stop-and-go operation.
† Short Haul service applies to vehicles that annually travel up to 30,000-60,000 miles (48,000-96,000
kilometers) and average between 5.1 and 5.9 miles per gallon.
‡ Severe service applies to vehicles that annually travel up to 30,000 miles (48,000 kilometers) and average
less than 5 miles per gallon or that operate under severe conditions. Service applies to vehicles that
annually travel up to 30,000 miles (48,000 km) or that operate under severe conditions. Only one of
these conditions needs be met to categorize an application as Severe Service.
§ Whichever comes first.
Table 4-1 Maximum Oil Drain and Filter Change for Series 60, MBE 4000, DD13,
DD15, and DD16 using PGOS 93K218 Approved Oils with ULSD Fuel
Service Application
Long Haul * Short Haul † Severe ‡
Engine Series
15,000 miles 6,000 miles
20,000 miles
MBE 900 (24,000 km), (9,600 km),
(32,000 km)
500 h or 6 mon§ 250 h or 3 mon§
* Long Haul service (over-the-road transport) applies to vehicles that annually travel more than 60,000 miles
(96,000 km) with minimal city stop-and-go operation. Examples of Long Haul service are: regional delivery
that is mostly freeway mileage, interstate transport, and any road operation with high annual mileage.
† Short Haul service applies to vehicles that annually travel up to 60,000 miles (96,000 km) or with a load
factor over 45% and operate under normal conditions. Examples of Short Haul service are: operation
primarily in cities and densely populated areas, local transport with infrequent freeway travel, or a high
percentage of stop-and-go travel.
‡ Severe service applies to vehicles that annually travel up to 30,000 miles (48,000 km) or that operate
under severe conditions. Examples of Severe Service are: idle time over 35%, load factor over 55%,
operation on extremely poor roads or under heavy dust accumulation; constant exposure to extreme hot,
cold, salt-air, or other extreme climates; frequent short-distance travel; construction-site operation; city
operation (fire truck or garbage truck), or farm operation. Only one of these conditions needs be met
to categorize an application as Severe Service.
§ Whichever comes first.
NOTE: Load factor and idle time values must be based on DDEC reports that accurately represent the
current service application.
Table 4-2 Maximum Oil Drain and Filter Change Intervals for MBE 900 using
PGOS 93K218 Approved Oils with ULSD Fuel
Table 4-3 Maximum Oil Drain and Filter Change Intervals for Pre-2007 Series
60, Series 55, MBE 900, MBE 4000 Engines Using PGOS Approved
Oils with ULSD Fuel
NOTE:
The oil drain interval are based on engine hours and fuel consumption.
Figure 4-1 Oil Drain Interval in Hours for Pre-2007 MBE 900 On-Highway
Engines
Detroit diesel recognizes the desire by some fleets to maximize oil drain and filter change
intervals beyond those listed in Table 4-1, Table 4-2, and Table 4-3. While Detroit Diesel
has no formal program to extend these intervals, it will assist fleets in an advisory capacity to
minimize equipment risks. Before a fleet embarks on an extended oil drain interval program,
Detroit Diesel recommends:
□ The fleet reviews its current maintenance program to ensure oil changes are performed
properly and on time. A missed oil drain interval during an extended oil drain interval
program will create a significant risk to the equipment.
□ The fleet reviews the severity of the operation. High idling intervals, high load factors, and
chronic mechanical problems are not conducive to extending the oil drain intervals.
□ The fleet selects oil and filter suppliers who have the expertise and products to support the
goals of such a program. They may include a field test results demonstration, formal
program for extending oil and filter changes, and a warranty covering failure of their
products in this service which results in a premature engine wear-out or failure.
Fleets are encouraged to review any drain extension program with Detroit Diesel before initiating
the program. While Detroit Diesel will not provide approvals for these programs, they will
provide feedback on the risk assessment.
Extending oil drain intervals will not void the Detroit Diesel product warranty. In the event of
engine failure or premature wear-out when running extended oil and filter change intervals,
Detroit Diesel will make a determination as to the extent, if any, that their workmanship and
materials were responsible. If Detroit Diesel determines that the failure or early wear-out was
related to workmanship or materials, warranty coverage of the repairs will apply. If the engine
fails or wears out within the Detroit Diesel warranty period and Detroit Diesel determines it was
the result of extending the oil drain intervals, any claim for reimbursement of expenses under the
terms of the engine warranty will be denied.
ASTM DD13,
Conditions MBE MBE
Characteristics or Other 40, 50, 60 55 DD15,
Measured 900 4000
Methods DD16
Viscosity at 100 °C, D 445 12.5
Engine & Oil
cSt, Min DIN 51562 SAE 15W-40
Viscosity at 100 °C, D 445 21.9
Engine & Oil
cSt, Max DIN 51562 SAE 15W-40
TGA Engine
Soot, %* 4.5†
(E1131) Combustion
1/3 New or
Total Base No., Min D4739 Oil
3.0 mg KOH/g
D2896 1/3 New or
Total Base No., Min Oil
ISO 3717 3.0 mg KOH/g
D2982
Glycol, Max Engine Negative
DIN 51375
Water, Max E203 Engine 0.3%
Fuel Dilution, Max D3524 Engine 2.5% 7%
Fe, Max ‡ D5185 Engine Wear 200 ppm
Al Max‡ D5185 Engine Wear 30 ppm 50 ppm
Si Max‡ D5185 Engine Wear 30 ppm 50 ppm
Cu, Max§ D5185 Engine Wear 30 ppm 50 ppm
Pb, Max‡ D5185 Engine Wear 30 ppm 10 ppm
Engine Coolant
Na, Max ‡ D5185 100 ppm
Leak
Engine Coolant
K, Max § D5185 150 ppm
Leak
* Infrared spectroscopy (ASTM E 168/DIN 51452) may also be used, provided it is calibrated to be equivalent
to the TGA method.
† With PGOS approved oils
‡ These are general limits. Wear metal limits must be determined for specific application and oil used.
§ Results may exceed limits during engine break-in period; see Section 4.7 for more information.
NOTE: These limits are intended as guidance when a single oil sample is tested and are based on the
normal oil drain intervals listed in Table 4-1. Actual limits are dependent on engine, application,
drain interval and oil type. Refer to Detroit Diesel Publication DDC-SVC-MAN-0047 for determining
warning limits specific to your application.
5 DIESEL FUEL
The quality of fuel used is a very important factor in obtaining satisfactory engine performance,
long engine life, and acceptable exhaust emission levels. For EPA07 and EPA10 exhaust
compliant engines equipped with exhaust aftertreatment devices, the use of Ultra-Low Sulfur
Diesel (ULSD) fuel is critical to the function and service life of these devices. Use of this fuel
in pre-2007 engines will provide cleaner combustion, less soot, and fewer fuel-related deposits.
ULSD fuel is recommended by Detroit Diesel for use in Series 60, Series 50, Series 55, MBE
900, MBE 4000, DD13, DD15, and DD16 engines.
NOTE:
When prolonged idling periods or cold weather conditions below 0°C (32°F) are
encountered, the use of 1-D fuel is recommended. However; note that transit coach
engines are emission certified on either No. 1 or No. 2 fuel. To maintain emission
compliance, only use the correct certified fuel.
125,000 –
Heat Content, Net, BTU/gal D 4868 – 128,500 – 130,900
127,300
Lubricity Wear Scar, µm,
D 6079 – 460 460
Maximum
* The flash point temperature is a safety-related property which must be established according to applicable
local requirements.
† The cloud point and filter plugging point temperature should be equal to, or below the lowest ambient
temperature to prevent clogging of fuel filters by wax crystals.
‡ No free water is visible.
It is recommended that all fuels used in Detroit Diesel engines meet the minimum lubricity
requirements listed in Table 5-1, “Diesel Fuel Specifications.” Fuels not meeting the lubricity
requirements may be additized to meet them.
Premium diesel fuels are not covered by any existing industry specification. It is recommended
that the customer obtain additional information from the fuel marketer and compare properties to
those listed in Table 5-1 before using.
Detroit Diesel supports biodiesel as a renewable fuel. Biodiesel fuels are mono alkyl esters of
long chain fatty acids commonly referred to as Fatty Acid Methyl Esters (FAME) and are derived
from renewable resources through a chemical process called transesterification. Detroit Diesel
approves the use of biodiesel fuel blends up to 5% maximum by volume in diesel fuel providing
the following three conditions are met:
□ The biodiesel used in the blend must meet ASTM D 6751 or EN 14214 specifications.
□ The biodiesel used in the blend must be sourced from a BQ-9000 Accredited Producer or a
BQ-9000 Accredited Marketer.
□ The finished blend must meet the fuel properties listed in Table 5-1 and either ASTM
D 975 or EN 590 specification.
Detroit Diesel is responsible for the materials and workmanship of its engines. Failures attributed
to the use of fuels which do not meet industry standards are not the fault of Detroit Diesel and will
not be covered by the Detroit Diesel product warranty. While Detroit Diesel supports the use
of B5, the use of unacceptable quality fuel that does not meet industry standards can result in
warranty denial. Refer to Chapter 7 for more details regarding Detroit Diesel’s warranty coverage.
5.2.1 DISTILLATION
Although many specifications contain only a partial listing of the distillation results (Distillation
Temperature at 90% Recovered, for example), this is not enough to determine the quality and
suitability of the fuel for use in diesel engines. Diesel fuels are blended products which may
contain high boiling constituents that can affect combustion. Only use fuels with a minimum 98%
recovery by distillation. Use the full boiling range as listed in Table 5-1 for proper selection.
Fuel can be burned in an engine only after it has been completely vaporized. The temperature at
which the fuel is completely vaporized is described as the “End Point Temperature” in Distillation
Test Method, ASTM D 86. Since this temperature is difficult to measure with good repeatability,
the fuel's 90% or 95% distillation point is often used. Detroit Diesel specifies the 95% temperature
because it is closer to the end point than the 90% used in ASTM D 975.
Cetane Number is a relative measure of the time delay between the beginning of fuel injection
and the start of combustion. In a cold engine, a low cetane number will cause difficult starting
and white exhaust smoke until the engine warms up. In engines with charge air cooling, a low
cetane number fuel may also cause white exhaust smoke during light load operation. A minimum
cetane number of 43 is specified for best engine performance. However, the cetane number alone
should not be considered when selecting a quality fuel. Other properties, such as 95% distillation
temperature and carbon residue, should also be considered.
Calculated Cetane Index is sometimes reported instead of Cetane Number. Cetane Index is an
empirical property determined mathematically from boiling range temperatures and specific
gravity of the fuel, whereas Cetane Number is determined through an engine test. Additives
may be used by the fuel marketer to improve the cetane number; however, they have no effect
on cetane index. Evaluate both properties when selecting diesel fuel. The effect of biodiesel
fuel on Calculated Cetane Index is unknown.
Diesel fuel oxidizes in the presence of air, heat, and water. The oxidation of fuel can result in
the formation of undesirable gums and black sediment. Such undesirable products can cause
filter plugging, combustion chamber deposit formation, and gumming or lacquering of injection
system components, with resultant reduced engine performance and fuel economy. Two tests are
specified for fuel stability, ASTM Test Method D 2274 (Accelerated), which measures diesel fuel
storage oxidative stability, and ASTM Test Method D 6468, which measures high temperature
stability. Conduct ATSM D 6468 at 150°C (302°F). The results of ATSM D 6468 are based on a
visual rating of the filter pad by the amount of light reflected from the filter pad. A 100% rating
is a clean pad, while a 50% rating is very dirty. ATSM D 2274 is a weighed measure of the
sediment filtered from the fuel after storage. Although the results of ATSM D 2274 may vary
with actual field storage, it does measure characteristics that will affect fuel storage stability for
periods of up to 12 months.
Since January 2007, 80% of diesel fuel sold for On-Highway use must be ULSD fuel (below
15 ppm). Until the complete phase-in of ULSD fuel in December, 2010, dispensing pumps
must be identified with the sulfur level of the fuel being sold. If operating EPA07 compliant
engines, or older engines with API CJ-4 oils, it is highly recommended that only ULSD fuel be
used. Fuels with sulfur content above 15 ppm are not recommended for these engines due to
poisoning of aftertreatment devices and the corrosion of EGR components. Engines, particularly
EGR-equipped engines, operated on 500 ppm sulfur fuel and API CJ-4 oils may require a
reduction in oil drain intervals.
Since diesel fuel provides cooling of the injection system, the temperature of the fuel may vary
considerably due to engine operating temperature. As fuel temperature increases, fuel viscosity
decreases along with the lubrication capabilities of the fuel. Maintaining proper fuel temperatures
and selecting fuels with the viscosity ranges listed in Table 5-1, “Diesel Fuel Specifications”, will
ensure the injection system functions properly.
When operating with reduced fuel viscosity or elevated fuel temperatures, the injectors will
operate at reduced internal clearances. As a result, dirt and smaller particulate material may cause
injector durability concerns. Change filters on Detroit Diesel On-Highway engines to those
specified for “Severe Duty Service.” Installing a fuel cooler or operating with fuel tanks above
half full may also help eliminate the concern.
Some fuel additives provide temporary benefit when fuel is contaminated with water. They are
not intended to replace good fuel handling practices. Where water contamination is a concern,
equip the fuel system with a fuel/water separator and service it regularly. In marine and other
environments where microbe growth is a problem, a biocide may be used. Microbial activity
may be confirmed with commercially available test kits. When checking for microbial activity,
collect fuel samples from the bottom of the fuel tank. Follow the manufacturer's instructions for
treatment. Avoid the use of biocides containing chlorine, bromine, or fluorine compounds, since
these may cause fuel system corrosion. When small amounts of water are present, supplemental
additives containing methyl carbitol or butyl cellusolve are effective. Follow the manufacturer's
instructions for their use. The use of isopropyl alcohol is no longer recommended due to its
negative effect on fuel lubricity.
□ Used Lubricating Oil – Detroit Diesel specifically prohibits the use of drained lubricating
oil in diesel fuel. Used lubricating oil contains combustion acids and particulate materials,
which erode injector components, resulting in loss of power and increased exhaust
emissions. In addition, the use of drained lubricating oil will increase maintenance
requirements due to filter plugging and combustion deposits. Refer to section 3.10, “Waste
Oil Disposal and Rerefined Oils,” for recommendations on proper used oil disposal.
□ Gasoline - The addition of gasoline to diesel fuel will create a serious fire hazard. The
presence of gasoline in diesel fuel will reduce the fuel cetane number and increase
combustion temperatures.
□ Ethanol - The addition of gasoline to diesel fuel will create a serious fire hazard. The
presence of ethanol in diesel fuel will reduce the fuel cetane number and increase
combustion temperatures.
Drain and clean tanks that contain such mixtures as soon as possible. Detroit Diesel will not
be responsible for any detrimental effects which it determines resulted from the use of used
lubricating oil, gasoline, or ethanol in diesel fuel.
Many supplements available today are intended to be added to the fuel by the customer. These
include a variety of independently marketed products which claim to be:
□ Cetane Improvers
□ Emission Control Additives
□ Detergents
□ Combustion Improvers
□ Smoke Suppressants
□ Cold Weather Flow Improvers
Should a customer decide that a supplemental additive is temporarily required, the following
is intended to provide guidance to the customer in evaluating potential safety hazards and
deleterious engine effects.
□ Review a Material Safety Data Sheet (MSDS) carefully for special handling instructions
and hazardous material content. Additives containing hazardous materials should not be
used due to personal safety risk.
□ Get a detailed compositional analysis from the supplier. Ash forming metallic elements
and corrosive elements must not be present. Additives containing calcium, barium,
zinc, phosphorous, sodium, magnesium, iron, copper, and manganese are known to
cause combustion ash deposits that can foul fuel injectors and create deposits which may
adversely affect cylinder life. Halogenated compounds containing chloride, fluoride,
and bromide are corrosive, as are some sulfur- containing compounds. Avoid the use of
additives with these components.
□ Many commercial diesel fuels today contain performance additives, particularly those
marketed as premium diesel fuel. Any supplemental additive being considered must be
compatible with the fuel it is to be used in. Evaluate a mixture containing twice the
recommended concentration of additive for compatibility to represent an overdosage
condition, using the tests listed in Table 5-1, “Diesel Fuel Specifications”.
□ Conduct performance evaluation of a fuel supplemental additive in customer equipment
for a minimum of six months. Testing should be a side-by-side comparison with and
without the additive to verify performance claims. Testimonials do not guarantee similar
performance in all applications.
Supplemental fuel additives are not recommended due to potential injector system or engine
damage. Our experience has been that such additives increase operating costs without providing
benefit. The use of supplemental fuel additives does not necessarily void the engine warranty.
However, repair expenses which result from fuel system or engine component malfunctions or
damage attributed to their use will not be covered. Accompany these products with performance
data supporting their merit as well as the manufacturer's warranty policy. Detroit Diesel will not
test or verify the performance of any supplemental additives and will not accept responsibility for
use, selection, or hazards relating to the use of such products.
NOTICE:
Do not use galvanized steel or sheet metal tanks and galvanized
pipes or fittings in any diesel fuel storage, delivery, or fuel system.
The fuel oil will react chemically with the zinc coating, forming a
compound which can clog filters and cause engine damage.
6 FILTRATION
Filters make up an integral part of fuel and lubricating oil systems. Proper filter selection and
maintenance are important to satisfactory engine operation and service life. Use filters, however,
to maintain a clean system, not to clean up a contaminated system.
NOTE: A fuel/water separator assembly may be used in place of the primary filter assembly, but not together
with it. For Series 50 and Series 60 engines the fuel/water separator filter number is 23535985.
NOTE: The numbers after the Sea Pro name indicate the Gallon Per Hour (GPH) flow capacity of the filter.
(Does not apply to Fuel Pro filters.)
Higher Filtration
Engine Series Filter Type Qty Part No.
Part No.
Series 50 Spin-On 2 23530573 —
Series 55 Spin-On 1 5241800310 —
Series 60 Spin-On 2 23530573 DELF3998
Series 60 (Pre-1993) Spin-On 2 23530407 23530409
Series 60 (Pre-1993) Spin-On 1 23530413 —
MBE 904 Cartridge 1 0001801609 N/A
MBE 906 Cartridge — 0001801709 N/A
MBE 4000 Cartridge — 0001802109 N/A
DD13, DD15, DD16 Cartridge 1 A4721800109 N/A
Detroit Diesel is not responsible for the cost of maintenance or repairs due to the lack of
performance of required maintenance services or the failure to use fuel, oil, lubricants,
and coolants meeting Detroit Diesel-recommended specifications. Performance of required
maintenance and use of proper fuel, oil, lubricants, and coolants are the responsibility of the
owner. For full details, see the engine operator's guide for your engine.
8 SUPPLEMENTAL INFORMATION
Specifications referred to in this publication and other related information may be obtained by
contacting the following sources:
SAE Standards
Society of Automotive Engineers
Technical Publications
400 Commonwealth Drive
Warrendale, PA 15096-0001
www.sae.org
ASTM Annual Book of Standards, Section 5
100 Barr Harbor Drive
West Conshohocken, PA 19428-2959
www.astm.org
API Annual List of Licensees and Other Publications
American Petroleum Institute
1220 L Street Northwest
Washington, D.C. 20005
Directory of Licensees: www.eolcs.api.org
DIN Deutsches Institut für Normung e. V. (DIN EN)
Burggrafenstraße 6
10787 Berlin
Germany
www.din.de
International Organization for Standardization (ISO)
1, ch. de la Voie-Creuse
Case postale 56
CH-1211 Geneva 20
Switzerland
www.iso.org