Professional Documents
Culture Documents
Acid-Base Titration by Dan Holmquist
Acid-Base Titration by Dan Holmquist
24
Acid-Base Titration
A titration is a process used to determine the volume of a solution needed to react with a given
amount of another substance. In this experiment, you will titrate hydrochloric acid solution, HCl,
with a basic sodium hydroxide solution, NaOH. The concentration of the NaOH solution will be
given and you will determine the unknown concentration of the HCl. Hydrogen ions from the
HCl react with hydroxide ions from the NaOH in a one-to-one ratio to produce water in the
overall reaction:
When an HCl solution is titrated with an NaOH solution, the pH of the acidic solution is initially
low. As base is added, the change in pH is quite gradual until close to the equivalence point,
when equimolar amounts of acid and base have been mixed. Near the equivalence point, the pH
increases very rapidly, as shown in Figure 1. The change in pH then becomes more gradual
again, before leveling off with the addition of excess base.
In this experiment, you will use a pH electrode to monitor pH as you titrate. The region of most
rapid pH change will then be used to determine the equivalence point. The volume of NaOH
titrant used at the equivalence point will be used to determine the molarity of the HCl.
pH
Figure 1
MATERIALS
CBL System stirring bar
TI Graphing Calculator 50-mL buret
Vernier pH Amplifier and pH Electrode ring stand
Vernier adapter cable 2 utility clamps
TI-Graph Link 10-mL pipet
HCl solution, unknown concentration pipet bulb or pump
~0.1 M NaOH solution 250-mL beaker
magnetic stirrer (if available) distilled water
PROCEDURE
1. Obtain and wear goggles.
2. Use a pipet bulb (or pipet pump) to pipet 10 mL of the HCl solution into a 250-mL beaker.
Add 50 mL of distilled water. CAUTION: Handle the hydrochloric acid with care. It can
cause painful burns if it comes in contact with the skin.
3. Place the beaker on a magnetic stirrer and add a stirring bar. If no magnetic stirrer is
available, you need to stir with a stirring rod during the titration.
Figure 2
¥ Plug the pH amplifier into the adapter cable in Channel 1 of the CBL System. The pH
electrode is already connected to the pH amplifier.
¥ Use the link cable to connect the CBL System to the TI Graphing Calculator. Firmly press
in the cable ends.
5. Use a utility clamp to suspend a pH electrode on a ring stand as shown in Figure 2. Position
the pH electrode in the HCl solution and adjust its position so that it is not struck by the
stirring bar.
6. Obtain a 50-mL buret and rinse the buret with a few mL of the ~0.1 M NaOH solution.
Dispose of the rinse solution as directed by your teacher. Use a utility clamp to attach the
buret to the ring stand as shown in Figure 2. Fill the buret a little above the 0.00-mL level of
the buret with ~0.1 M NaOH solution. Drain a small amount of NaOH solution so it fills the
buret tip and leaves the NaOH at the 0.00-mL level of the buret. Record the precise
concentration of the NaOH solution in your data table. CAUTION: Sodium hydroxide
solution is caustic. Avoid spilling it on your skin or clothing.
7. Turn on the CBL unit and the calculator. Start the CHEMBIO program and proceed to the
MAIN MENU.
10. Press ENTER after the pH system has warmed up 30 seconds. Before adding NaOH titrant,
monitor the pH value on the CBL screen. Once the pH has stabilized, press TRIGGER on the
CBL and enter Ò0Ó (the buret volume, in mL) in the TI calculator. You have now saved the
first data pair for this experiment.
11. You are now ready to begin the titration. This process goes faster if one person manipulates
and reads the buret while another person operates the calculator and enters volumes.
¥ Select MORE DATA to collect another data pair. Add the next increment of NaOH titrant
(enough to raise the pH about 0.15 units). When the pH stabilizes, press TRIGGER and enter
the current buret reading (to the nearest 0.01 mL). You have now saved the second data
pair for the experiment.
¥ Select MORE DATA. Continue adding NaOH solution in increments that raise the pH by
about 0.15 units and enter the buret reading after each increment. When a pH value of
approximately 3.5 is reached, change to a one-drop increment. Enter a new buret reading
after each increment. Note: It is important that all increment volumes in this part of the
titration be equal; that is, one-drop increments.
¥ After a pH value of approximately 10 is reached, again add larger increments that raise the
pH by about 0.15 pH units, and enter the buret level after each increment.
¥ Continue adding NaOH solution until the pH value remains constant.
12. Select STOP AND GRAPH from the DATA COLLECTION menu when you have finished
collecting data. Examine the data points along the displayed graph of pH vs. NaOH volume.
As you move the cursor right or left, the volume (X) and pH (Y) are displayed below the
graph. To determine the equivalence point, go to the region of the graph with the large
increase in pH. Examine the data in this section to find the largest increase in pH upon the
addition of 1 drop of NaOH solution. Find and record the NaOH volume just before this
jump. Then record the NaOH volume after the drop producing the largest pH increase was
added.
13. Use the TI-Graph Link cable and program to transfer the graph of pH vs. volume to a
Macintosh or IBM-compatible computer. Print a copy of the graph. Then use the program to
print a copy of the NaOH volume data in L1 and the pH data in L 2.
14. Dispose of the beaker contents as directed by your teacher. Rinse the pH electrode and return
it to the storage solution.
2. Determine the volume of NaOH added at the equivalence point. To do this, add the two
NaOH values determined above and divide by two.
3. Calculate the number of moles of NaOH used.
4. See the equation for the neutralization reaction given in the introduction. Determine the
number of moles of HCl used.
5. Recall that you pipeted out 10.0 mL of the unknown HCl solution for the titration. Calculate
the HCl concentration.
Concentration of NaOH
________ M
NaOH volume added
before largest pH increase ________ mL
NaOH volume added
after largest pH increase ________ mL
________ mL
Moles NaOH
________ mol
Moles HCl
________ mol
Concentration of HCl
________ mol/L