Professional Documents
Culture Documents
S1 Access Control User Manual
S1 Access Control User Manual
User Manual
Please read the operation steps before installation
1. Introduction:
This series of RFID card access control is working with card only, password only, Card +
password, or the password working in one single door controller. It used the chip is that is up to
industrial grade single chip. With high stability, large capacity, full function, and reaction fast and
simple operation. It is best for used on company office ,factory, houses, residential quarters,
offices, mechanical and electrical control equipment and so on.
2. Functions
1, Storage 2000 card (ID / IC optional)
2, Can be continuous-read and enroll card, and automatically default the card number and card
password
3, With these 2 functions: swipe card for open the door or swipe card for closed the door
4, The signal for open the door is output by relay control directly (NO / NC optional)
5, Three models for open the door:Card or PIN, Card +PIN, password.
3. Technical Features
N Item Specification
O
1 Power supply DC: Voltage 12±10%;current<0.1A
2 Max Output Electro lock output:2A
3 Ambient temp -10℃—70℃
4 RH 20%—90%
5 Capacity 2000 user card and 1 password
6 Reading distance 5—15cm
7 Card type Proximity or Mifare card
4. Status Indication
Description Red LED Green LED Buzzer
Normal Mode ON
Program Mode Flash
Under Program mode ON
Swipe Non registered ON Di(long)
Card
Swipe Card Only ON, the door is open at Di Di (short)
the same time
Card and Password Red and Green LED
Mode(after swipe card, blink interactively
pending for password
entry)
Card and Password Flash red LCD each
Mode 0.5 second
Password Only Mode Flash red LCD each 1
second
Keypad Di (short)
Setup Successfully Di Di (short)
Setup Failure Di (long)
Invalid Input Di (long)
Alarm Di Di Di Continuously
5. Programming Guide
(1)How to get into Program Mode
Press # # # # RedLED OFF, Green LED ON .Then press 123456#,
If successfully ,RedLED OFF and Green LED On ,or RedLED ON
And Green LED OFF means you are fail .Try again (Provided that you
didn’t change your default Program password .Default value is 123456
(4)How to add single card with card number (Can be multi-cards operation as well)
Press 2(swipe card…apply to unregistered card only) XXXX“card number”
#(repeat this step until the last card)#
If this is a registered card, controller will DI(long)for warning, you still
can continue your operation by swiping an other new card.
If this is a registered card number, controller will Di(long)for warning,
you still can continue your operation by entering another card number.
(8)How to set access password ( default access password is empty, it is not activated yet)
Press 6 (new password) # (new password) # ,then it is ok. But it must be in 6 digits format
Press 6 # # Password will be deactivated
(9)If you want to exit Program mode, pls press * to exit e the program mode)
(10)How to change card password (It apply to Card And Password mode only)
Press * (Green LED ON)(swipe registered card)(input old password)(Red and
Green LED flashed alternatively)(input new password)#(input new password again)#
If Green LED OFF, Di Di(short),it means changing this card’s password successfully.
If Di(long), it means you fail to complete this operation. Please try again.
(11)How to reset to the factory default value ( only reset password and system parameters, card won’t
be deleted)
Cut off the power, put the JP4 jumper in 1-2 position and turn on the devices.
After DI DI(short),put the JP4 jumper in 2-3 position. Then restore factory setting successfully.
6. Instance operation
(1) How to change program password to 456789(form default password)
First enter the program mode by Press # # # # 123456 # (Green LED flashed)
Press 0 +456789 # 456789 #
Press * (exit the program mode),then your program password became
into 456789.
(3) How to add two cards with card number 0011and 0022
First enter the program mode by Press # # # #123456#(Green LED flashed)
Press 2 (swipe card) 0011 # (swipe card) 0022 # #
Press * (exit the program mode)
(4) How to delete cards numbered 0011 and 0022
First enter the program mode by Press # # # # 123456 #(Green LED flashed)
Press 31 0011 # 0022 # #
Press * (exit the program mode)
7. Wires Connection
J5 Main port output
Red +(9-12V)
Black GND
Green NC Only relay signal output
White COM
Blue NO
Yellow OPEN Push/Exit Button, the others connect to GND
Gray GND
Black GND
Green D0
White D1
Blue Lighting control and voice control lines
J2 Doorbell button
Purple Doorbell button output, press the button to closure
Purple