Work, Power and Energy Activities
Work, Power and Energy Activities
Activity 1
LITTLE SHOP OF TOYS
Objectives:
At the end of the activity, you should be able to:
o energy forms present in the operation of simple toys,
and o describe the energy transformations in the toys.
Materials Needed:
yoyo
friction toy car
deflated balloon
2 mystery objects
Activity Sheet / science notebook
Procedure:
1. Operate each toy to move and observe closely what causes it to start
and stop moving.
2. For each toy, identify all forms of energy involved in the process.
3. Trace the energy transformations by sketching and labeling the toy
while in motion.
4. From inside the room, choose two objects/toys of interest to you. Do steps
1 to 3.
5. For each toy or object, answer the following questions:
Questions:
Q1. What does the toy or object do?
Q2. What energy changes take place as this toy or object operates?
Q3. What form does the stored energy start out in?
Q6. What made each object to move a certain displacement and what
made each object to come to a stop?
Conclusion:
Name:___________________________________ Year & Sec:___________
Score:_______
Teacher:_________________________________ Date:________________ Rating:______
Activity 2
Hep Hep Hooray!
Objectives:
At the end of the activity, you should be able to:
construct a simple turbine unit
demonstrate mechanical energy transformations, and
demonstrate Hydroelectric Power (HEP) using a water
reservoir system.
Materials Needed:
plastic folder or acetate
permanent marker pen
ruler or tape measure
pair of scissors
cutter
juice drink straw
hot melt glue or super glue (cyanoacrylate adhesive)
masking tape
thread
5-10pcs paper clips
2 1.5-Liter plastic bottle
1 push
pin 3-inch
nail
2 3-Liter ice cream container
2-Liter bottled tap water
supply hand towel or rag
funnel
activity sheet / science notebook
Safety Precautions:
Procedure:
A. Construction of the Turbine Model
1. Prepare 8 blades for the turbine. Cut 2 inch by1 inch strips of plastic
folder or acetate. Shape it any way you want.
Figure 6. a) shaped strips for turbine blades
2. Glue the blades to the middle of the straw similar to the sample in Fig. 6
b). The straw will serve as the shaft of the turbine.
3. Make a turbine holder using one of the plastic bottles. Use a push pin
then a 3-in nail to make holes at a 10-cm height to hold the straw.
Ensure that the turbine can rotate freely. If needed, make some plastic
stopper to hold the turbine in place.
1. From the bottom of the bottle, measure and mark with dots
the 5-cm, 10-cm, 15-cm, and 20-cm spots. These dots should
lie along the same vertical line and would be the exit points.
Acrosss these, make horizontal lines as tail water levels, ht.
2. Use the push pin to make a hole on each dot. Then put
masking tape over each hole. Fold the top as flap for
pulling.
3. Make another horizontal line 5 centimeters above the 20-cm
hole and mark asthe head water level, hwof the stored water.
4. Determine the stored water’s Head of Flow, H by taking the difference between
the head water level and the tail water level as indicated in the equation = ℎ −
ℎ . Record these values in Table 3.
8. Examine the water reservoir with the turbine model assembly and be
familiar with its operation. Reposition the turbine when needed.
Q7. What was the effect of the stored water’s head of flow to its range?
Q8. How would you explain this effect in terms of energy transformation?
Q9. In Question 4, you formulated your hypothesis regarding the effect of
the stored water’s height to the water’s range. What was your
hypothesis?
Q10. Was the hypothesis you made correct? Why or why not?
Q11. The data collected showed the effect of the head of flow on the
flow range and not on the water’s force that powers the blades to
rotate. How would you relate the range to the water’s force?
Q13. In a typical actual Hydroelectric Power (HEP) Plant, the turbines are
fixed and so the tail water level is constant (Refer to Figure 8). Only the
head water level from the reservoir varies depending on the stored water.
How would you modify this activity to model a real working HEP plant?
Conclusion:
Name:___________________________________ Year & Sec:___________
Score:_______
Teacher:_________________________________ Date:________________ Rating:______
Activity 31
Bashing Ball!
Objectives:
At the end of the activity, you should be able to:
Materials Needed:
bowling ball or basketball
rope
ceiling
Procedure:
1. Ask a custodian or a maintainance personnel to hang a bowling ball or a
basketball using a mesh or a net from the ceiling. Make sure that the
ceiling is stable and sturdy.
2. After the teacher demonstrates the activity, ask for a willing and
brave volunteer from the class.
3. Have the student grab the ball and walk backwards carefully until the
ball is level with his/her nose.
4. Ask the student to remain still as possible while holding the ball against
the tip of his/her nose. Make sure the string is taut so the ball will swing
smoothly and evenly when it is released.
5. Warn the student to keep his body still, especially the head. S/he should
not move his/her head backward or forward.
6. Ask the student to release the ball without any additional push.
Questions:
Q1. Did the bowling ball reach the tip of the nose of the student volunteer?
Did it rise higher or lower than its original height?
Q2. At what location(s) along the path of the bowling ball is the ball’s
kinetic energy highest?
Q3. At what location(s) along the path of the bowling ball is the ball’s
gravitational potential energy highest?
Conclusions:
Name:___________________________________ Year & Sec:_____________ Score:________
Teacher:_________________________________ Date:_______________ Rating:______
Activity 2
Bouncy Balls, Revisited
Objectives:
At the end of the activity, you should be able to:
a bouncing ball is not conserved
Materials:
three balls of different masses,
ruler or meter stick
Procedure:
1. Drop each ball from a height of your choice. Measure the height of the
bounce of each ball. Perform three trials for each ball. Note how each
ball bounces upon impact.
2. Record the heights in the table below.
3. Calculate the velocity of the ball just before it hits the ground and after it
hits the ground.
Q1. Which equation(s) can you use to calculate these velocities?
4. Calculate the kinetic energies of the ball just before it hits the ground and
after it hits the ground.
5. Get the difference in the kinetic energies of the ball.
Conclusion: