Professional Documents
Culture Documents
I HtgMKTGLiteraturePDFsModine7-115 0
I HtgMKTGLiteraturePDFsModine7-115 0
Modine offers a complete line of indoor and outdoor direct gas- This catalog describes in detail the Model Series MCV/MVV
fired make-up air units, which is summarized in Table 2.1. Direct Fired Make-Up Air Units. Included are product design
benefits, construction features, performance data, control
applications, as well as the available options and accessories.
Table 2.1 - Modine Direct Fired Make-Up Air Unit Product Portfolio j
Typical CFM Range
Unit Type Unit Orientation 800-1,600 1,600-14,000 14,000-30,000 30,000-45,000 45,000-60,000
MCV/MVV
Horizontal
100% Outside Air MDB
Vertical MDB
Recirculating Horizontal MRB
j Actual airflow range capability depends on a number of factors, primarily related to total static pressure the blower must overcome. For
information on the MDB/MRB units, please refer to the latest revision of Catalog 7-150 or the Breeze® AccuSpec selection program.
! WARNING WARNING
!
Do not locate ANY gas-fired unit in areas where chlorinated, Do not install in potentially explosive or flammable atmosphere
halogenated or acid vapors are present in the atmosphere. laden with dust, sawdust, or similar airborne materials.
As Modine has a continuous product improvement program, it reserves the right to change design and specifications without notice.
2 7-115.0
direct fired make-up air unit - model series mcv/mvv
7-115.0 3
design features
Digit 4,5,6 - Casing Size and Blower Wheel Size Digit 9,10,11,12 - Maximum Input Capacity (MBH)
Designates the Casing Size (1-5) and the Blower Size (08-20). Manifold/burner combinations are sized based on available
Each has a defined airflow capability range. burner lengths and manifold component capabilities. The
model number will reflect the maximum rating for the selected
Table 5.1 - Casing Size and Blower Wheel Sizes manifold/burner combination, however the actual firing rate will
be set to meet actual job requirements.
Airflow Range
Casing Size Blower Size Blower Size (CFM)
(Digit 4) (Digits 4,5) Description Table 5.2 - Maximum Input Capacity
Min. Max.
Digits 9-12 Maximum Input Capacity
1 08 10 x 8” 800 2,200
290 290,000 Btu/Hr
10 10 x 10” 1,400 3,500
2 375 375,000 Btu/Hr
12 12 x 12” 2,400 3,500
625 625,000 Btu/Hr
3 15 15 x 15” 3,200 8,000
750 750,000 Btu/Hr
4 18 18 x 18” 5,000 9,500
938 937,500 Btu/Hr
5 20 20 x 20” 5,500 14,000
1125 1,125,000 Btu/Hr
1200 1,200,000 Btu/Hr
Digit 7 - Unit Configuration
1500 1,500,000 Btu/Hr
Designates the discharge location and controls access side.
1875 1,875,000 Btu/Hr
The control side is determined by looking into the intake of the
unit and then specifying the access side (right or left hand). 2100 2,100,000 Btu/Hr
Includes access to gas manifold compartment and electrical
control wiring compartment. All units are horizontal orientation. Example:
See Figure 5.1. Unit is to be sized for a firing rate of 1,758,400 Btu/Hr (1758
MBH). The unit would be ordered with Digits 9-12 of the
Figure 5.1 - Unit Configurations - Graphical model number selected as 1875 (1500 MBH would be too
small). When the unit is produced, it will be setup to have an
LEFT HAND ACCESS RIGHT HAND ACCESS
actual capacity of 1758 MBH.
7-115.0 5
model nomenclature description
6 7-115.0
model nomenclature description
7-115.0 7
OPTIONS - FACTORY INSTALLED - Control cabinet
Figure 8.1 - Standard Feature and Factory Mounted Option Locations - Control Cabinet
3c 6
4 4
1 3b
7
5 17a 8
5
2
23
9 11 10 12
3a 7 16
15a
15b
23
16
17c
14 22
19
15a
13
18 17b
20 21
23
The following refer to Figure 8.1. These items are described in greater detail on the following pages. Note that (S) indicates a
Standard feature and (O) indicates an Optional feature.
1. (O) Non-Fused Disconnect Switch 14. (S) 24V Isolation Transformer
2. (O) GFI Convenience Outlet 15. (O) Timed Freeze Protection, consisting of:
3. (O) Building Pressure Control, consisting of: a. Low Limit Discharge Duct Stat
a. Outdoor Pressure Pickup b. Freeze Protection Timer
b. Indoor Pressure Pickup with Tubing 16. (S) High Temp Limit Stat
c. Pressure Transmitter 17. (O) Cabinet Temperature Control, consisting of:
4. (O) High and Low Gas Pressure Switches a. Enclosure Mounted Thermostat
5. (S) Control Power Transformer and Fuses b. Enclosure Cooling Fan
6. (S) Flame Safeguard Control c. Enclosure Heater
7. (O) Variable Frequency Drive 18. (O) Inlet Gas Pressure Gauge
8. (O) Control Relay 19. (S) Temperature Control Amplifier
9. (S) High Air Flow Cutoff Switch 20. (S) Main Gas Valve
10. (S) Low Air Flow Proving Switch 21. (S) Modulating Gas Valve
11. (S) High Profile Pressure Switch 22. (O) Manifold Gas Pressure Gauge
12. (S) Low Profile Pressure Switch 23. (S) Profile Pressure Test Ports (Qty 2)
13. (S) Profile Bypass Damper Motor
8 7-115.0
OPTIONS - FACTORY INSTALLED - Control cabinet
The following details the standard and factory installed options 7. (O) Variable Frequency Drive
available as shown in Figure 8.1. [(S)=Standard, (O)=Option] Units with model number Digit 2=V are equipped with
a factory installed VFD to provide control of air volume
1. (O) Non-Fused Disconnect Switch
through varying the speed of the blower from 100% down
Factory installed on the stationary panel next to the door to as low as 35%. The VFD can be programmed to
provides convenient method of turning off power to the provide any one of the following control configurations:
unit. Also available as fused.
• Constant Speed (field adjustable): VFD will operate
2. (O) GFI Convenience Outlet at full speed but can be adjusted in the field.
Includes a 115V/1ph duplex weatherproof service • Two Speed: VFD will operate at full rated speed
receptacle mounted on the exterior of the cabinet. or user defined low speed. The remote panel will
Available as either powered by others (shown) or powered include a High/Low speed switch for high/low speed
from unit (not shown). When powered by unit, the unit changeover.
includes an additional unit mounted disconnect switch and
• External 4-20mA or 0-10Vdc Control Signal: VFD
step-down transformer for supply voltages above 115V.
can be externally controlled from full rated speed down
3. (O) Building Pressure Control to 35% of rated speed. Unit includes terminals for
This configuration is typically used to maintain a slightly landing external control wiring.
positive pressure in the building to reduce infiltration. It • Building Pressure Control: See option 3 note for
is also used to provide variable volume make-up air for information on this control configuration.
buildings that have multiple exhaust loads that cannot be
8. (O) Control Relay
interlocked to one make-up air unit. This option includes
the following factory installed items: Includes double-pole, double throw (DPDT) contacts for
a. Outdoor Pressure Pickup sequence of operation control switching. The function of
the relays must be specified at the time of order.
b. Indoor Pressure Pickup with Tubing (route to space)
9. (S) High Air Flow Cutoff Switch
c. Pressure Transmitter
The switch monitors the pressure drop across the burner
The pressure transmitter monitors the space pressure
to insure the air flow through the burner does not exceed
relative to the outdoor air pressure and adjusts the VFD
the maximum design velocity. The switch is electrically
speed from full rated speed to as low as 35% of rated
interlocked with the flame safeguard control (#6).
speed to bring in more or less outside air.
10. (S) Low Air Flow Proving Switch
4. (O) High and Low Gas Pressure Switches
The switch monitors the pressure drop across the burner
The low gas pressure switch monitors the gas supply
to insure that sufficient air flow exists before allowing the
pressure ahead of all the gas train components to ensure
burner to operate. The switch is electrically interlocked with
there is sufficient pressure for proper ignition. If the gas
the flame safeguard control (#6).
pressure is below the setpoint of the switch, the flame
safeguard controller is disabled and the switch must be
manually reset to allow the unit to function. Items 11 through 13 are part of the Auto-VelocityTM profile
The high gas pressure switch monitors the gas pressure system that constantly and automatically adjusts a burner
between the gas manifold components and the burner to profile bypass damper to maintain proper burner air velocity
ensure the gas pressure has not exceeded the maximum for optimal combustion. The system has a range of operation
rating. Gas pressures above the maximum rating may to allow for correction of airflow changes from filters becoming
damage the gas train components or cause the unit to dirty, changes in airflow when using a VFD, or slight changes
overfire. If the gas pressure is above the setpoint of the in system duct static. It does not eliminate the requirement for
switch, the flame safeguard controller is disabled and the proper system balancing at commissioning.
switch must be manually reset to allow the unit to function. Please proceed to the following page for details on each
5. (S) Control Power Transformer and Fuses component in this system.
For supply voltages greater than 115V, a transformer is
used to reduce the voltage for the unit controls.
6. (S) Flame Safeguard Control
The flame safeguard control monitors safety devices to
determine if the gas ignition sequence should be initiated.
Once initiated, the control will also monitor a flame rod
flame sensor to ensure proper burner flame control. The
control includes a pre-purge timer to clear any residual gas
in the unit before ignition can be initiated. The ignition type
varies by unit capacity as follows:
• Digits 9-12=0290-1125 MBH: Direct Spark
• Digits 9-12=1200-2100 MBH: Interrupted Pilot
7-115.0 9
OPTIONS - FACTORY INSTALLED - Control cabinet
The Auto-VelocityTM profile system components are as follows a. Low Limit Discharge Duct Stat: The control is
(refer to Figures 8.1 and 10.1): mounted in the control cabinet while the sensor is
11. (S) High Profile Pressure Switch mounted in the blower cabinet (see Figure 11.1).
b. Bypass Timer: The 5 minute timer allows the unit to go
The switch monitors the pressure drop across the burner
through the normal start-up sequence while temorarily
and if the pressure is too high (excessive airflow), the
bypassing the low limit discharge duct stat.
profile bypass damper motor (#13) is energized to adjust
the profile balancing damper to allow more airflow to 16. (S) High Temp Limit Stat
bypass the burner to reduce the pressure drop (velocity) to The high temperature limit control prevents the burner from
the acceptable range. firing if excessive heated air temperatures are experienced.
12. (S) Low Profile Pressure Switch The limit control is mounted on the blower housing and is
electrically interlocked with the flame safeguard control.
The switch monitors the pressure drop across the burner
and if the pressure is too low (reduced airflow), the profile 17. (O) Cabinet Temperature Control
balancing motor (#13) is energized to adjust the profile Cabinet temperature control options are available for
balancing damper to allow less airflow to bypass the burner units with a factory mounted VFD. In extreme ambient
to increase the pressure drop (velocity) to the acceptable temperatures, the temperature in the cabinet can impact
range. the performance and longevity of the variable frequency
13. (S) Profile Bypass Damper Motor drive. Includes some or all of the following:
a. Enclosure Mounted Thermostat: Activates heating
The damper actuator is directly coupled to the profile
and/or cooling fan operation as needed. Always included
bypass damper and will increase or decrease the opening with either (b) or (c).
position based on changes in burner profile velocity as
b. Enclosure Cooling Fan: Required for locations where
measured by the high and low profile pressure switches
the unit is in ambient temperatures 85°F and higher.
(#11 and #12).
c. Enclosure Heater: Required for locations where
Figure 10.1 - Auto-VelocityTM Profile System - Burner View the unit is in ambient temperatures below 0°F. For
temperatures between 0° and 15°F, the heater is
recommended but not required.
18. (O) Inlet Gas Pressure Gauge
The inlet gas pressure gauge option allows a contractor
to easily determine if the gas pressure entering the unit
is within the range required without having to connect an
AIRFLOW DIRECTION external manometer.
19. (S) Temperature Control Amplifier
The amplifier converts the temperature control signal
BURNER from the discharge air temperature sensor (and room
temperature sensor if the Maxitrol 44 system is used) and
modulates the modulating gas valve (#20) to maintain the
BURNER PROFILE OPENING air temperature setpoint.
20. (S) Main Gas Valve
AUTO-VELOCITYTM PROFILE All units are supplied with redundant automatic main gas
SYSTEM BYPASS DAMPER shut-off valves to control gas flow to the modulating gas
valve (#21). These valves may be a combination gas valve
as shown in Figure 8.1 which have two valve seats in one
valve body (Digits 9-12=0625 and smaller), or two separate
valves on units with larger capacities.
21. (S) Modulating Gas Valve
The modulating gas valve is controlled by the temperature
control amplifier (#19) to control the flow of gas to the
burner.
22. (O) Burner Gas Pressure Gauge
The burner gas pressure gauge option allows a contractor
14. (S) 24V Isolation Transformer to easily determine if the gas pressure to the burner
A transformer, typically 115V to 24V or 24V to 24V is used matches the manifold pressure listed on the serial plate
to electrically isolate sensitive controls from the rest of the to ensure the unit is firing at the correct capacity without
control circuit. having to connect an external manometer.
15. (O) Timed Freeze Protection 23. (S) Profile Pressure Test Ports (2)
A low limit duct stat monitors the discharge air temperature, Used during startup to easily connect a manometer to
and if below the setpoint, the unit will shut down to prevent measure profile pressure drop during unit balancing.
delivery of cold air. Includes the following:
10 7-115.0
OPTIONS - FACTORY INSTALLED - blower cabinet
Figure 11.1 - Standard Features and Factory Mounted 4. (S) Blower/Motor Vibration Isolation
Option Locations - Blower Cabinet All units include neoprene blower/motor assembly vibration
isolation as standard. For more robust vibration isolation,
the following are options are detailed further on page 7:
1 • Rubber-In-Shear isolation on all sizes (see in Fig 11.1).
• Spring isolation on all except Casing Size 1.
5
5. (S) Supply Blower Motor
7 2 6. (S) Adjustable Motor Base
Provides adjustability of the motor position to ensure
correct drive belt tension.
6
7. (S) Maxitrol Discharge Air Sensor
3
15a 16
Standard for Maxitrol 14 and 44 gas controls systems, the
sensor provides functions specific to the gas control type.
8 9
• Maxitrol 14: The sensor measures the discharge air
temperature and provides feedback to the Maxitrol 14
controller to maintain the discharge air temperature
setpoint by modulating the gas valve.
• Maxitrol 44: The sensor measures the discharge air
4 10 temperature and provides feedback to the Maxitrol
44 controller to limit the modulation range so that
temperatures do not fall outside the allowed range.
For more information, refer to page 6.
The following details the standard and factory installed options
available as shown in Figure 11.1. [(S)=Standard, (O)=Option] 8. (S) Wiring Harness - Control Wiring
The 10 foot long pre-wired harness in flexible conduit
allows for quick connection to the remote panel mounted
1. (S) Flame Observation Port
in the space. The wires are numbered to correspond to a
Provides visible indication of the flame and flame quality numbered terminal strip within the remote panel.
while the unit is operating and without needing to open the
9. (S) Wiring Harness - Power Wiring
casing.
The 10 foot long pre-wired harness in flexible conduit
2. (S) DWDI Blower Wheel
allows for quick connection to the supply power for the unit.
Double Width, Double Inlet blower wheel with sizes as
10. (S) Floor Mounted Wiring Chase
indicated on page 5.
Provides an easy pathway through the floor of the unit
3. (S) Blower Bearing Assembly
to route the Control and Power Wiring Harnesses to the
Most blower assemblies are available with either space without needing to drill holes. See Figure 11.2.
permanently lubricated spider bearings or greaseable pillow
block bearings. Figure 11.2 - Floor Wiring Chase
• Spider Bearings: Standard for Casing Sizes 1-4, not
available on Casing Size 5. Spider bearings include
blower mounted bearing brackets with ball bearings.
Spider bearings are designed for use in lower torque
applications as seen on the smaller blowers.
• Pillow Block Bearings: Optional for Casing Sizes
1-4, standard for Casing Size 5. The pillow block
bearing option includes two heavy duty pillow block
bearing housings rigidly fastened to two blower
support channels. Pillow block bearings are available
for all applications, but are required for high torque
applications seen on larger blowers.
(O) Extended Bearing Grease Lines (not shown)
Extended grease lines are an available option for pillow
block bearings. They include factory installed grease 15a. (O) Timed Freeze Protection
lines extending from the blower bearings to Zerk fittings
The timed freeze protection discharge sensor. See page
on the outside of the unit cabinet.
10 for a full description of this feature.
16. (S) High Temp Limit Stat
The high temp limit discharge sensor. See page 10 for a
full description of this feature.
7-115.0 11
OPTIONS - FACTORY INSTALLED Side Access filter section
4
1 1
3 4
The following details the standard and factory installed options available as shown in Figure 12.1. [(S)=Standard, (O)=Option]
1. (O) Side Accessible Filters 3. (O) Mild Temperature Inlet Duct Stat
The side access filter section is optional and is used to Used to automatically shut off the burner when the inlet
filter outside air drawn through the unit. Available either air temperature reaches the desired setpoint to prevent
painted or unpainted to match the unit. The section is the burner from continually running at low fire during mild
available with several filter configurations: outdoor air temperature conditions.
• 2” permanent, aluminum mesh washable filters 4. (O) Inlet Dampers
• 2” disposable MERV 8 pleated filters Used to prevent building air from exiting the building
• 2” disposable MERV 13 pleated filters through the unit when the unit is not operating. Both
2. (O) Dirty Filter Switch standard and low leak dampers are available. The inlet
damper option includes a 2-position damper actuator that
A differential pressure switch that measures the pressure
is available as either power or spring closed. The damper
drop across the filter media. When the pressure drop
actuator includes an end switch to prevent unit operation
exceeds the setpoint, the switch closes which can be used
unless the dampers are open.
to indicate the filters need to be serviced.
Field installed discharge dampers are available. Please
see Accessories section for additional details.
12 7-115.0
this page intentionally left blank
7-115.0 13
ACCESSORIES - FIELD INSTALLED - remote panel
1 2 3 4
1
4
6 5
5
Note: The remote monitoring panel shown represents
the "Large" panel. The "Standard" panel is smaller
and does not include a lockable cover.
The following details the standard and factory installed options available as shown in Figure 14.1. [(S)=Standard, (O)=Option]
14 7-115.0
ACCESSORIES - FIELD INSTALLED - Remote panel/other
Inlet Hood
Used to prevent entry of rain into the fresh air opening of the
unit and includes mesh bird screen on opening. Available
either painted or unpainted and with or without 2” permanent
aluminum mesh washable filters. Inlet hood is shipped knocked
down for field assemby.
7-115.0 15
option - factory installed evaporative cooler
Evaporative Cooling Module The following details the standard and factory installed options
Outdoor units can be provided with a factory installed available as shown in Figures 14.1 and 14.2. [(S)=Standard,
evaporative cooling module. When applicable, evaporative (O)=Option]
cooling is one of the most economical means of supplying
conditioned air to a space. 1. (S) Water Supply Connection
The evaporative cooler used on the MCV/MVV Series units is a Includes a hand shut-off valve as standard. An accessory
simplified, non-recirculating design that reduces up-front costs Water Supply Valve Kit (not pictured) is available that
and maintenance. The cooler operation is explained in the provides the following:
description of the standard and factory installed options. • Supply water valve (2-way)
• Supply line drain valve (2-way)
Benefits of the non-recirculating design are the following: • Freeze stat
• A recirculation pump and float switch are not required. When ordered, this kit is shipped loose for field installation
• No sump required, reducing maintenance and water usage in a frost free environment (typically below the roof line).
to reduce microbial growth that can occur from poorly Refer to the Installation & Service Manual for additional
maintained recirculating systems. details.
• There is a continuous wash-down of the media with fresh 2. (S) Internal Water Control Valve (IWCV)
water to keep it flushed, increasing the lifespan of the Valve controlled by the Liquid Level Controller (LLC) to
media and reducing maintenance. allow water flow to the water distribution piping when wetted
• There is reduced risk of freeze damage that can be seen media is required.
with recirculating units with a sump. 3. (S) PVC Water Distribution Piping
Table 16.1 - Evaporative Cooler Performance Data The piping includes spray nozzles that uniformly distribute
water on the face of the media.
Unit Casing Size Evap Cooler Media Area
(Digit 4) Size Max CFM (sq. ft.) 4. (S) Evaporative Cooling Media
1 EVCNR1 2,200 4.00 The standard media is Munters 12" CELdek® Celluose
2 EVCNR2 3,500 5.78 evaporative cooling media.
EVCNR3 5,000 9.17 For applications requiring UL 900, Class 2 fire rating
3
EVCNR4 7,500 13.33 and compliance with NFPA codes, optional Munters 12"
EVCNR4 7,500 13.33 GLASdek® Fiberglass media is offered. The media is
4
EVCNR5 9,500 20.00 accessible from the side access opening (media access
EVCNR5 11,000 20.00 cover removed for display purposes).
5
EVCNR6 14,000 25.00
Figure 16.1 - Evaporative Cooler - Side Access Figure 16.2 - Evaporative Cooler - Inlet Air Opening
8 3
10
4 11
3
2
6
1
6
16 7-115.0
5. (S) Overflow Water Sensor (OWS) (not shown) the face area of the cooling media as shown in Table 16.1.
On a call for cooling, the Liquid Level Controller (item 7) Example: Determine the final dry bulb temperature for a unit
monitors the overflow water sensor, located at the bottom with Casing Size 4, rated airflow of 8000 CFM, installed in
of the media, and opens the IWCV (item 2) to provide water Phoenix, Arizona. Also, determine the approximate gallons
flow to wet the media. When the OWS senses moisture, per hour evaporated and the apparent cooling capacity of the
that is indication that the media is saturated and the LLC evaporative cooler.
turns off the IWCV to conserve water. The following are the steps to determine the solution to the
6. (S) 304 Stainless Steel Casing and Pitched Drain Pan example problem above:
Stainless steel offers outstanding corrosion resistance. 1. The 1.0% design conditions are 110°F DB/70°F WB.
Includes shipped loose adjustable leveling legs for support 2. There are two options for Casing Size 4 units shown in
(not shown). Table 14.1, however only one can be operated at 8000
7. (S) Liquid Level Controller (LLC) CFM, the EVCNR5 unit. The Media Area is 20.0 ft2. The
Controller that monitors the OWS (item 5) to determine if air velocity is then calculated as follows:
the IWCV (item 2) should be open or closed. Optimizes FPM = CFM / Media Face Area = 8000 CFM / 20 ft2 = 400 FPM
water consumption to avoid excessive water usage. 3. The media effectivness is determined in Figure 17.1
8. (S) Outdoor Air Thermostat (Y-axis) by finding where the effectiveness curve intersects
Measures the outside air temperature and if the 400 FPM velocity on the X-axis. In this example, the
temperature is above the setpoint, a call for cooling is effectiveness is approximately 90%.
initiated to the LLC (item 7). 4. Determine final dry bulb air temperature of conditioned air
9. (O) Freeze Stat by using the following formula:
Measures the outside air temperature and if the LAT = EAT DB – (% Eff. x (EAT DB – EAT WB))
temperature is below the setpoint, prevents the evaporative LAT = 110°F – (0.90 x (110°F – 70°F)) = 74°F DB
cooler supply water valve from being energized. This is 5. The gallons per hour evaporated is calculated as follows:
part of the Water Supply Valve Kit discussed in item 1. G.P.H. = (1.2 x CFM x (EAT DB - LAT DB)) / 10,000
10. (S) Wiring Terminal Strip G.P.H. = (1.2 x 8,000 CFM x (110°F - 74°F)) / 10,000 = 34.6
The wiring terminal strip provides an easy means of 6. The cooling capacity, Q, of the unit is defined as the
connecting the flexible conduit wiring harness from the apparent cooling capacity because it is dependent on a
unit (item 8 on page 11) to the remote panel. The wiring specific set of temperature conditions. As these conditions
harness wires are numbered, as are the corresponding change, so will the apparent cooling capacity. The formula
terminals on the terminal strip. is as follows:
11. (O) 2" Permanent Aluminum Mesh Pre-Filters Q = 1.08 x (EAT DB – LAT DB) x CFM
Optional pre-filters (not shown) can be added in the empty Q = 1.08 x (110°F – 74°F) x 8,000 CFM = 311,040 Btu/Hr
slot indicated by item 11. The filters are accessible from
the side access opening (filter access cover removed for
display purposes). Definition of Terms
Also available as a field installed accessory (not shown) is EAT = Entering Air Temperature
an inlet hood that can be with or without 2" thick permanent LAT = Leaving Air Temperature
aluminum mesh filters. DB = Dry Bulb
WB = Wet Bulb
Evaporative Cooling Performance Example % Eff. = Percent Effectiveness
Evaporative cooling works by placing a wet media in the Q = Apparent Cooling Capacity
entering air stream of the cooling unit. As the air passes through
the media, sensible heat from the air is transferred to the water
in the cooling media, causing the water to evaporate. Because
the sensible heat from the air is simply transferred to the water,
Figure 17.1 - Evaporative Cooler Effectiveness Curve
and both the water vapor and cooled air remain in the system,
there is no net energy change in the system. However, the dry
bulb temperature of the air has been lowered and provides 100%
Effectiveness
Figure 18.1 - Unit Dimensions (without Evap Cooler or Side Access Filter Section) (inches)
CASING SIZE 1 CASING SIZES 2-5
C 7-1/2
C 7-1/2 J F
J F
8
D
OUTSIDE
AIR
BOTTOM OUTSIDE BOTTOM
SUPPLY AIR SUPPLY
E AIR A E
A AIR
OPENING OPENING
OPTIONAL DISCONNECT
SWITCH
OPTIONAL DISCONNECT
SWITCH INLET GAS CONNECTION
INLET GAS CONNECTION
H H
OUTSIDE
AIR
OUTSIDE F
AIR B
F T
B
T
G
G
3-5/16 3-5/16
SUPPLY OPTIONAL MOTORIZED SUPPLY
AIR AIR OPTIONAL MOTORIZED
INLET DAMPER INLET DAMPER
J F J F
ELEVATION VIEW ELEVATION VIEW
Note: The drawing above is a general drawing for both Unit Configurations (Digit 7) = "B" (Left Hand Access, Straight Discharge) and "D" (Left Hand
Access, Bottom Discharge) for reference. For Unit Configurations other than "B" or "D", please see the Breeze® AccuSpec generated submittal
package for the selected unit.
Table 18.1 - Unit Dimensions (without Evap Cooler or Side Access Filter Section) (inches)
Discharge Direction Inlet Opening
Bottom
Straight or Top
Unit N U
Size A B C D E F G H J S T (Width) (Height)
108 28 24 50 10-1/2 12-1/2 13-3/8 6-7/8 3-3/4 8 N/A N/A 19-7/8 22
210 32 30 72 8-7/16 15-1/8 13-3/8 6-7/8 9-3/4 8 N/A N/A 22-7/8 28
212 32 30 72 7-3/16 17-5/8 15-7/16 8-1/4 6-5/16 9-1/4 N/A N/A 22-7/8 28
315 40 33 92 9-11/16 20-5/8 17-7/8 9-3/8 5-3/4 10-1/2 N/A N/A 28-7/8 31
418 48 38 96 12-1/16 23-7/8 20-7/8 11 6-1/8 12-1/4 N/A N/A 36-7/8 36
520 55 48 96 14-1/8 26-3/4 26-3/4 12-15/16 8-5/16 13-1/2 N/A N/A 43-7/8 46
18 7-115.0
DIMENSIONS - units (with Side Access Filter Section)
Figure 19.1 - Unit Dimensions (with Side Access Filter Section) (inches)
CASING SIZE 1 CASING SIZES 2-5
S
S
C 30
C 30 J F
8 J F
D
BOTTOM OUTSIDE
OUTSIDE BOTTOM AIR
E SUPPLY SUPPLY
AIR AIR A E
A AIR
OPENING OPENING
OPTIONAL DISCONNECT
OPTIONAL DISCONNECT SWITCH
SWITCH
INLET GAS CONNECTION
INLET GAS CONNECTION
H
H
OUTSIDE
F SUPPLY AIR AIR
OUTSIDE
AIR B
F SUPPLY AIR T
B
T
G
G
3-5/16 3-5/16
SUPPLY SUPPLY
AIR SIDE ACCESS AIR
FILTER SECTION J F
J F SIDE ACCESS V-BANK
FILTER SECTION
ELEVATION VIEW ELEVATION VIEW
Note: The drawing above is a general drawing for both Unit Configurations (Digit 7) = "B" (Left Hand Access, Straight Discharge) and "D" (Left Hand
Access, Bottom Discharge) for reference. For Unit Configurations other than "B" or "D", please see the Breeze® AccuSpec generated submittal
package for the selected unit.
Table 19.1 - Unit Dimensions (with Side Access Filter Section) (inches)
Discharge Direction Inlet Opening
Bottom
Straight or Top
Unit N U
Size A B C D E F G H J S T (Width) (Height)
108 28 24 50 10-1/2 12-1/2 13-3/8 6-7/8 3-3/4 8 80 27-5/16 19-7/8 22
210 32 30 72 8-7/16 15-1/8 13-3/8 6-7/8 9-3/4 8 102 30-5/16 22-7/8 28
212 32 30 72 7-3/16 17-5/8 15-7/16 8-1/4 6-5/16 9-1/4 102 30-5/16 22-7/8 28
315 40 33 92 9-11/16 20-5/8 17-7/8 9-3/8 5-3/4 10-1/2 122 36-5/16 28-7/8 31
418 48 38 96 12-1/16 23-7/8 20-7/8 11 6-1/8 12-1/4 126 41-5/16 36-7/8 36
520 55 48 96 14-1/8 26-3/4 26-3/4 12-15/16 8-5/16 13-1/2 126 51-5/16 43-7/8 46
7-115.0 19
DIMENSIONS - Evaporative cooler
30 K
7-1/2
OPTIONAL
INLET HOOD
SUPPORT/LEVELING LEGS
3-5/16
OPTIONAL MOTORIZED OPTIONAL 2" PERMANENT
INLET DAMPER INLET SIDE ACCESS FILTERS NOTE: INLET HOOD &
BIRDSCREEN SHIP
KNOCKED DOWN FOR
1/2" DRAIN 1/2" SUPPLY FIELD ASSEMBLY
CONNECTION CONNECTION AND INSTALLATION.
ELEVATION VIEW
20 7-115.0
DIMENSIONS - inlet hood and roof curb
INLET HOOD
OUTSIDE AIR
Note: The center divider panel shown above only CURB DETAIL
applies to units with Casing Size 3 and larger.
7-115.0 21
this page intentionally left blank
22 7-115.0
this page intentionally left blank
7-115.0 23
Products from Modine are designed to provide indoor air-comfort and ventilation
solutions for residential, commercial, institutional and industrial applications.
The Modine brand has been the Whatever your heating, ventilating and air conditioning requirements, Modine
has the product to satisfy your needs, including:
industry standard since Arthur B.
HVAC
Modine invented and patented
• Unit Heaters:
the first lightweight, suspended – Gas
– Hydronic
hydronic unit heater in 1923.
– Electric
No other manufacturer can – Oil
• Ceiling Cassettes
provide the combined application
• Duct Furnaces
flexibility, technical expertise and • Hydronic Cabinet Unit Heaters, Fin Tube, Convectors
fast delivery found at Modine. • Infrared Heaters
• Make-up Air Systems
Consult your local Modine
• Unit Ventilators
distributor for help in solving your
Ventilation
indoor air problems. • Packaged Rooftop Ventilation
School Products
• Vertical Packaged Classroom HVAC:
– DX Cooling/Heat Pump
– Water/Ground Source Heat Pump
– Horizontal/Vertical Unit Ventilators
Geothermal
• Water-to-Water
• Water-to-Air
• Combination
Specific catalogs are available for each product. Catalogs 75-136 and 75-137
provide details on all Modine HVAC equipment.