Professional Documents
Culture Documents
Fast Track Troubleshooting: Downloaded From Manuals Search Engine
Fast Track Troubleshooting: Downloaded From Manuals Search Engine
Press Freezer button one Press Freezer button a Press Freezer button a Press Freezer button a
time at the Test Mode to second time to Force third time to Force Low forth time to Force De-
Force Compressor High Mid Speed Run Speed Run frost of Fridge & Freezer,
Speed Run, measure fan measure defrost voltage
and Compressor volt- at main PCB
ages at main PCB
Refrigerant Charge
R134a 5.64 oz. Sales Mode, No Compressor Operation
Sealed System
Press Energy Saver & Freezer temp buttons
simultaneously for 3 sec ( you will hear a “Ding
Dong”) to remove or put into Sales Mode. When in
the Sales Mode the Display will show "OF" "OF"
Removing power will not cancel this mode.
Brushless DC Fan motors are used to save energy. The fans operate at two speeds. Fan speed information is read by
the Main PCB. If the fan speed exceeds 600 RPM or the speed is too slow, or stopped the fan drive circuit is disabled,
After 10 seconds the circuit tries again with 3 seconds of DC voltage If the fan continues this activity for 5 cycles, 10
seconds off 3 seconds on, the fan drive circuit is disabled for 10 minutes.
TO TEST THE FAN CIRCUIT VOLTAGE.
Power off and back on to check the DC voltage to the motor, wait from 10 to 60 seconds for the fan voltage to kick in,
and then check fan voltage, the average reading is 9 VDC. If you get 3 seconds of voltage every 10 seconds for the 5
fan power up cycles, then the Main PCB is good.
NOTE: You may need to put unit in FORCED FREEZE mode to activate the fans/compressor.
If the fan blade is blocked by ice, then defrost and check the motor again, after removing power from the unit.
If the evaporator is ice blocked and thus blocking the air flow, the fan will over RPM and is stopped. Remove ice and
check the motor again. If everything is clear around the fan blade then the motor would be at fault. Continuous fan errors
will be displayed on the front panel display. PLEASE NOTE: The door switches control the evaporator fan motors. Have
them closed to test the motors. Delay time 10 – 60 seconds.
Heat Release Ice Makers
Heat Release Ice production Explanation Heat Release I/M Test Mode
38 minutes after the water fill is complete, the control Press and hold the ICE TEST S/W for at least 1.5sec, the
board will check the temperature of the eject Thermistor, harvest function will start. If the ice maker Thermistor is be-
on the Ice Maker Head, if the Thermistor reads a tem- low 0 degrees the Ice maker heater turns on for about 2 min-
perature lower than 18.5 degrees for more than 5 sec- utes. If the temperature exceeds 0 degrees, Ice maker
onds, then the ice production process is completed. The heater turns on for 30 seconds. After the Ice maker heater
Ice maker will harvest if the ice bucket is not sensed as turns on for 30 seconds, the heater turns off and then Ice
full. If a Fault Mode is detected with the Ice Maker op- maker harvest motor turns on. The motor will rotate in right
eration, the Ice Maker stops working for 3 hours. Which direction for about 3 minutes, after this, water supply valve is
means, the Ice Maker checks the operation every 3 turned on, then the valve is turned off, the test mode is com-
hours until it works properly. pleted. If the above operation is not carried out within 6 min-
utes, it will go into a fault mode.
Refrigerator Room Sensor Error- open or short-circuit, connector The voltage at MAIN PCB
R-SENSOR
failure. Cause is also a temperature reading > 122°or < -58 ° F. Sensor between 4.5V~1.0V
DEFROST SENSOR Ref. Defrost Sensor Error- open or short-circuit, connector failure. The voltage at MAIN PCB
OF R ROOM Cause is also a temperature reading > 122°or < -58 ° F Sensor between 4.5V~1.0V
This error indicates the Refrigerator Evap Fan is not spinning at the Fan voltage at MAIN PCB
R-FAN ERROR
correct RPM or the fan feedback line is open. shall be between 7V~12V
I/M FUNCTION This error indicates the Ice tray has not returned to level after an ice
Replace I/M
ERROR(R on Twin I/M) harvest. The error is displayed after three failed attempts.
Refrigerator Room defrost heater- open or short-circuit, connector Disconnect defrost connector
R-DEFROSTING
failure, or defective temperature fuse/bi-metal. Defrost on over 80 from PCB, check resistance
ERROR
minutes
PANTRY-DAMPER- Sensor system in Pantry Room errors Disconnect heater connector
HEATER ERROR from PCB, check resistance
PANTRY-SENSOR CR Room Sensor Error- This can be an open or short-circuit, contact The voltage of MAIN PCB
ERROR failure. Cause is also a temperature reading > 122°or < -58 ° F. Sensor between 4.5V~1.0V
Disconnect heater connector
WATER HEATER Error is displayed when the water reservoir tank heater is open or
from PCB, check resistance
ERROR shorted
Ambient Temp. Sensor Error- open or short-circuit, connector failure. The voltage at MAIN PCB
EXT-SENSOR
Cause is also a temperature reading > 122°or < -58 ° F Sensor between 4.5V~1.0V
Freezer Compartment Sensor Error- open or short-circuit, connector The voltage at MAIN PCB
F-SENSOR
failure. Cause is also a temperature reading > 122°or < -58 ° F Sensor between 4.5V~1.0V
Freezer Room Defrost Sensor Error- open or short-circuit, connector The voltage at MAIN PCB
F-DEF-SENSOR
failure. Cause is also a temperature reading > 122°or < -58 ° F Sensor between 4.5V~1.0V
This error indicates the Freezer Evap. Fan is not spinning at the Fan voltage at MAIN PCB
F-FAN ERROR
correct RPM or the fan feedback line is open. shall be between 7V~12V
This error indicates the Condenser Fan is not spinning at the correct Fan voltage at MAIN PCB
C-FAN ERROR
RPM or the fan feedback line is open. shall be between 7V~12V
FRENCH DOOR ICE Ice Room Sensor Error- open or short-circuit, connector failure. The voltage at MAIN PCB
ROOM SENSOR Cause is also a temperature reading > 122°or < -58 ° F Sensor between 4.5V~1.0V
F-DEFROSTING Freezer defrosting heater- open or short-circuit, connector failure, or Disconnect defrost connector
ERROR defective temperature fuse/bi-metal. Defrost on for over 80 minutes from PCB, check resistance
FRENCH DOOR ICE This error indicates the Ice Room Compartment Evap. Fan is not Fan voltage at MAIN PCB
ROOM FAN ERROR spinning at the correct RPM or the fan feedback line is open. shall be between 7V~12V
Uart ERROR This error is not applicable, if the error is detected during diagnostic
No Repair Necessary
COMMUNICATION testing please ignore it.
L↔M ERROR
Communication error within the Main PCB Replace main PCB
COMMUNICATION
Check wiring in door &
P↔M ERROR
Communication between the Main PCB and Keypad cabinet, Panel PCB, Main
COMMUNICATION
PCB
Protection
LED Blinking Frequency Test Replace
Functions
Check the Inverter PCB & Comp Connectors OK,replace Inverter PCB, if same,
Starting Failure
Relay Connectors replace compressor
Check System for restriction & refrigerant, if OK
SPM Fault If blinking after reset,
replace Inverter, if same, replace compressor
Detecting Connectors measure OK, replace compressor, if
Check Inverter Connectors,
Position Failure same, replace Inverter PCB
Motor Locked Compressor Locking Compressor
Compressor Locking, check input Replace Inverter PCB, if same, replace
Low Voltage
voltage Compressor
Compressor Locking, check input Replace Inverter PCB, if same, replace
Over Voltage
voltage Compressor
Downloaded from www.Manualslib.com
manuals search engine 4
Model : RFG297AA**/XAA CN71 All 120vac
nominal voltages listed CN74 A/C Load 120vac
3-(CN70-9) F Lamp (Prp-Red)
5 N (Gray)
1-(CN70-9) Cube Solenoid (Yel-Red)
9 Heater Common (Org)
3-(CN70-9) Auger Motor (Pnk-Red)
5-(CN70-9) Dispenser Valve (W/Blk-Red)
7-(CN70-9) Ice Maker Valve (Prp-Red)
9-(CN70-9) Ice Cover Route (Blu-Red) CN70 All 120vac
1-11 Disp Heater (Blk-Gry)
CN31 Sensor 3-11 French-Dsp Heaters (Yel-Gry)
1-4 Ambient Sensor (Wht-Wht) 1.2~2 vdc 5- (CN71-9) R Defrost (Wht-Org)
CN73 120vac
2-(CN90-8) I/M (Red-S/Blu) 5vdc 7- (CN71-9) F Defrost/Ice Duct heate
1-(CN70-9) I/M Heater (Brn-Red)
3-(CN76-1) Ice Room Sensor (Org-Gry) 3~3.8vdc 9- L1 (Red)
3-(CN70-9) I/M Motor (Wht-Red)
11- N (Gry)
CN78 Lamp/Veg LED
4-7 (Red-Gry) 13vdc CN50 Display
4-6 (Org-Pnk) 13vdc
5-6 (Yel-Pnk) 5vdc
CN77 Stepper Motor
8-6 Ice/Water Sw (Blu-P
1-( CN76-1) (Red-Gry) 13vdc
9-6 Ice Rte Sw 1(Prp-G
10-6 Ice Rte Sw 2 (Wht
CN91 Pantry Room Damper
BLU
+13V
BLU