Daisy 15XTP Pistol Manual
Daisy 15XTP Pistol Manual
MODEL 15XT By
CO2 SEMI-AUTOMATIC
This safety alert symbol indicates important safety messages in this manual.
When you see this symbol, be alert to the possibility of personal injury and carefully
read the message that follows.
The Model 15XT CO2 PowerLine® gun shoots with much more muzzle energy
than the traditional spring air BB gun. More power means greater chance of serious
injury or death. Use extreme caution when operating this gun.
Although your new PowerLine® gun is not a firearm, it has lethal potential and
should be treated with the caution and respect due any conventional firearm. Like a
firearm, your PowerLine® gun, when misused or carelessly used, can kill or seriously
injure the shooter or other persons. All safeties are mechanical devices and the
shooter is the only part of the system that can make a gun safe–or unsafe. DON’T
DEPEND ON MECHANICAL SAFETIES – think ahead and avoid situations that
might lead to accidents.
Guns differ in their operations and you are never ready to fire any gun until you
are thoroughly familiar with it. Read the following operating instructions and WITH-
OUT LOADING A PROJECTILE, proceed several times through the operating
steps with your gun (dry fire the gun at a safe target) so that you will be able to
operate the PowerLine® 15XT properly and safely.
15-SHOT BUILT-IN 3/8” DOVETAIL MOUNT
MAGAZINE REAR SIGHT
FRONT SIGHT
MUZZLE
3/8” DOVETAIL
MOUNT
TRIGGER GRIP
MANUAL TRIGGER
BLOCK SAFETY
2
PRIOR TO OPERATION
Put “ON” SAFE – NO RED SHOWING (refer to Operation Step 1, page 3).
OPERATION STEPS:
WARNING: Be sure gun is always pointed in a safe direction.
If desired, the gun may continue to be fired (Steps 5 and 6) until the built-in BB
magazine is empty or the CO 2 cylinder needs to be replaced. Once the built-in BB
magazine is empty, Steps 1,3,4,5,6, and 7 should be followed. If the CO 2 cylinder is
empty, then all 7 Steps should be followed. (Approximately 150 shots can be
expected per CO 2 cylinder).
NEVER STORE A LOADED GUN
At the end of a shooting session, as a safety precaution, always put “ON” safety
– NO RED SHOWING (refer to step 1, page 3), remove CO 2 cylinder (refer to page
7) and remove BBs from the Built-in Magazine. (refer to page 8). Store in a safe
place to prevent unauthorized use.
Step 1. PUT “ON “ SAFETY – POSITION SAFETY Step 5. TAKE “OFF” SAFETY – POSITION SAFETY
SO NO RED IS SHOWING (refer to page 3). SO RED IS SHOWING (refer to page 6).
Step 2. INSERT CO2 CYLINDER (refer to page 4). Step 6. FIRE (refer to page 6).
Step 3. FILL BUILT-IN MAGAZINE WITH A Step 7. PUT “ON” SAFETY – POSITION SAFETY
MAXIMUM OF 15 BBs (refer to page 5). SO NO RED IS SHOWING (refer to page 6).
Step 4. AIM AT A SAFE TARGET (refer to page 6).
HOW TO OPERATE
WARNING: Be sure gun is always
pointed in a safe direction. Never point the gun at SAFETY “ON”
NO RED SHOWING
anyone. Always assume and treat the gun as if it
were loaded and ready to fire.
STEP 1. PUT “ON” SAFETY – POSITION SAFE-
TY SO NO RED IS SHOWING.
Push the safety button to the right toward the
“SAFE” position – NO RED SHOWING (see Fig. 2).
In this position, the trigger cannot be pulled to fire
the gun. FIG. 2
CAUTION: Even when the safety is “ON”
you should continue to handle the pistol safely. Don’t point the gun at anything that
you don’t intend to shoot.
NOTE: The safety is not automatic. It will only do its job when you
do yours. With the index finger out of the trigger area, move the safety to the
“SAFE” position – NO RED SHOWING (see Fig. 2). REMEMBER, THE BEST SAFE-
TY IS GOOD GUN HANDLING.
3
STEP 2. INSERT CO2 CYLINDER
LEFT GRIP
WARNING: Use only CO 2 cylinders COVER
which are the 12 gram type. Any attempt to
use other sizes and/or cylinders containing
other types of gas could be extremely danger-
ous. The use of gases other than CO 2 could
result in an explosion or could rupture
the gun, causing serious injury.
FIG. 5
4
STEP 3. FILL THE BUILT-IN MAGAZINE WITH A MAXIMUM OF 15 BBs
1. Always point gun in a safe direction.
BUILT-IN MAGAZINE
Insure that the gun is “ON” safe BB FOLLOWER
– NO RED SHOWING (see Operation FULLY FORWARD
Step 1, page 3).
BUILT-IN
MAGAZINE
2. Move the Built-in Magazine BB
follower fully forward and hold in posi-
tion as shown. (see Fig. 6)
NOTE: Make sure the follower is
HELD Fully FORWARD toward the muzzle
OF THE GUN and THE SPRING
IS Clear of the loading port Before FIG. 6
Attempting to load BBs.
INSERT BBs
3. Once the Magazine BB follower is held INDIVIDUALLY
fully forward, a maximum of 15 .177 INTO THE
LOADING PORT
caliber BBs can be individually inserted
into the Magazine Loading Port as
shown. (see Fig. 7)
HOLD BB
CAUTION: Use only Max Speed™ FOLLOWER
BBs by Daisy®, or similar quality BBs that FULLY FOR-
WARD
are labeled as such. Do not use lead pel-
lets, buck shot, darts, ball bearings, or
FIG. 7
other foreign objects because they can
cause injury to someone or may damage
SLOWLY RELEASE
and/or jam the pistol. THE BUILT-IN MAG-
AZINE
4. After the Built-in Magazine has been BB FOLLOWER
loaded with a maximum of 15 BBs,
slowly release the Built-in Magazine BB
follower and allow it to rest up against
the BBs. This will allow the BBs to be
under spring tension (see Fig. 8).
NOTE: SLOWLY RELEASE THE BUILT-IN
MAGAZINE BB FOLLOWER – DO NOT
ALLOW IT TO SNAP REARWARD. FIG. 8
5
STEP 4. AIM AT A SAFE TARGET
To be a consistent marksman, use the correct sight picture each time you fire the
pistol (see Fig 9).
FIG. 9
CAUTION: Due to the power of the Model 15XT, use extra precaution in
selecting a safe target. Improper targets may cause ricochet.
STEP 5. TAKE “OFF” SAFETY – POSITION
SAFETY SO RED IS SHOWING.
When you are certain that the target, back-
stop and surrounding area is safe, position the
safety “OFF” – RED SHOWING (see Fig. 10). SAFETY “OFF”
RED SHOWING
Pulling the trigger now will fire the gun.
FIG. 11
6
BB DOES NOT FIRE
WARNING: If a BB does not fire after completing the operation steps, do
not assume that the gun is unloaded. Keep the gun pointed in a safe direction.
MAKE THE FOLLOWING CHECKS IF A BB DOES NOT FIRE
1. Did the Built-in Magazine contain .177 cal. Daisy® Max Speed™ or similar quality
BBs? If not, fill the Built-in Magazine with BBs and repeat the operation steps.
2. Was the safety “OFF” – RED SHOWING, when the trigger was pulled? If not,
repeat the operation steps.
3. Was a CO2 cylinder installed? If not, put “ON” safe – NO RED SHOWING, and insert
a new CO2 cylinder. Repeat the operation steps after the new cylinder is installed.
4. Refer to the section on CO2 characteristics (see page 8).
5. If the pistol still does not fire, refer to warning below.
WARNING: If the pistol still fails to shoot a BB after checking the five items
above, there is a malfunction in the pistol. This could represent a dangerous condi-
tion. There could be BBs in the pistol even though a BB did not shoot out. Al Always
treat the gun as if it were loaded. At no time should you look down the barrel of the
gun. Put “ON” safe – NO RED SHOWING, remove the CO2 cylinder, and send the pis-
tol directly to DAISY MANUFACTURING SERVICE DEPARTMENT. Refer to section on
REPAIRS OF DAISY GUNS.
HOW TO UNLOAD
After a shooting is complete, the gun should be unloaded before storing it. To
unload the gun always put “ON” safe – NO RED SHOWING, remove the CO2 cylinder,
and remove the BBs from the Built-in Magazine. See details below
CAUTION: Even though you have gone through an unloading procedure,
continue to treat the gun as though it were loaded. Don’t point at anything you don’t
intend to shoot. Always put “ON” safe – NO RED SHOWING.
REMOVE CO2 CYLINDER
1. Put “ON” safe – NO RED SHOWING. (see Operation
Step 1, page 3).
2. With the muzzle pointed in a safe direction and the left-
hand grip cover still in place, slowly turn puncture screw
counterclockwise allowing any remaining gas to be dis- LEFT GRIP
charged and continue turning screw until end stop is COVER
reached (see Fig. 12).
3. Remove left-hand grip cover by lifting at the bottom of
the grip.
4. Remove and properly dispose of CO2 cylinder. FIG. 12
STORAGE
Store your pistol unloaded. Put “ON” safe – NO RED SHOWING, remove CO2
cylinder and remove all BBs from the pistol’s Built-in Magazine. Keep pistol away
from children and untrained shooters. Store BBs, and CO2 cylinders separately from
the pistol to keep them from untrained shooters.
8
WARNING: A CO2 cylinder contains gas under pressure, whether or not it
has been inserted into a gun. If exposed to high temperatures (such as inside of a
closed car in direct sunlight), it could explode. Be sure to store all cylinders in a
cool place.
PROPER CARE
With care and periodic cleaning, your Model 15XT will provide many years of
shooting enjoyment. As is the case with conventional firearms, abuse, neglect, and
continued exposure to the elements will impair the performance of any airgun.
Learn to take care of your Model 15XT and it will serve you well.
CAUTION: Never attempt to clean the Model 15XT until the gun is “ON”
safe – NO RED SHOWING, the CO2 cylinder has been removed, and the BBs have
been removed from the Built-in Magazine.
EXTERIOR PARTS
All the plastic parts may be cleaned with a damp rag and mild soap or detergent.
Avoid using strong detergent, abrasive cleaning compounds or solvents that may
scratch or otherwise damage surfaces. The exposed metal parts should occasion-
ally be wiped clean using a soft cloth that is lightly oiled with clean motor oil.
LUBRICATION
Your Model 15XT was lubricated when built and should not require any additional
lubrication.
MODIFICATION
CAUTION: The components of this gun were engineered to deliver
optimum performance. Any modification or tampering with a gun may cause a mal-
function and may make it unsafe to use. Any change in performance (such as a
lowered trigger pull force and shortened trigger travel), indicates possible modifica-
tion, tampering and/or wear. Such a gun should be inspected, replaced or properly
repaired by qualified personnel. Any gun that has been dropped should be checked
by qualified personnel to ensure that its function has not been affected.
9
REPAIR OF DAISY GUNS
WARNING: A GUN THAT IS NOT OPERATING PROPERLY MAY BE
DANGEROUS. IT SHOULD BE KEPT SAFELY FROM USE BY ANYONE UNTIL
REPAIRED OR DESTROYED. DO NOT TRY TO TAKE THE GUN APART. IT IS
DIFFICULT TO REASSEMBLE, AND IMPROPER REASSEMBLY CAN CAUSE A
HAZARDOUS CONDITION.
GUNS IN WARRANTY LIMITED ONE-YEAR WARRANTY
For one year from date of purchase, Daisy will repair or replace and return this
gun, free of charge, if defective in material or workmanship. Service is available by
returning the gun to Daisy Outdoor Products (refer to important note below). Attach
to the gun, your name, address, and telephone number, description of problem and
proof of date of retail purchase (sales slip). Package and send transportation
prepaid to Daisy Outdoor Products. This Warranty gives you specific legal rights,
and you may also have other rights which may vary from state to state.
IMPORTANT: You can return your inoperative pistol to Daisy for repair via United
Parcel Service. Be sure to put “ON safety, remove CO2 cylinder and unload BBs
from the Quick Change Clip before returning the gun to Daisy. You must include
your street address for Daisy to send your pistol directly back to you through UPS
delivery.
GUNS OUT OF WARRANTY
If your Daisy needs repair, please call 1-800-713-2479 for repair charges. Daisy
will repair the gun or replace it with a reconditioned gun of the same model, if
available; otherwise, with a model of equivalent quality.
Daisy Outdoor Products
Service Department
308 West Stribling Drive
Rogers, AR 72756 U.S.A.
10
MODEL 15XT CO2 PISTOL SPECIFICATIONS
ACTION CO2 powered semi-automatic
11