Professional Documents
Culture Documents
G2.1u Service Manual PDF
G2.1u Service Manual PDF
Introduction .............................................................................................................................................. 3
Specifications ........................................................................................................................................... 5
Harness ................................................................................................................................................... 26
- 2 -
Introduction
The G2.1u is a multieffect processor with the following features and functions.
96 kHz / 24 bit sampling (with 32 bit internal processing) assures excellent sound quality. Frequency response
remains flat up to 40 kHz, and input-converted signal-to-noise ratio is an amazing 120 dB, demonstrating the high
level of performance achieved by the G2.1u. The G2.1u also has a USB connection and can be used as a direct
guitar/computer interface.
Out of a total of 54 effects, up to nine (including ZNR) can be used simultaneously. The high-quality choices
provided by the G2.1u include distortion effects that simulate the tones of famous amps and effects pedals, 6-band
guitar EQ and delay effects with "hold" control operated by foot switch.
The distortion effect module provides two different algorithms for each of its 17 effect types, one for live
performance and one for direct recording. Depending on the on/off setting of the CABINET & MIC effect which
simulates amp cabinet sound and mic characteristics, the most suitable algorithm is automatically selected, giving
you the best sound for any application.
A number of rhythm patterns using realistic PCM drum sounds are provided. This is convenient for use as a
metronome during individual practice or to provide a simple rhythm part for a quick session. An auto-chromatic
tuner for guitar is also built right into the unit, allowing you to easily tune your instrument also at home or on stage.
The combination of a rotary type selector and three parameter knobs make the effect editing process intuitive and
quick. The mute interval when switching patches has been reduced to less than 5 milliseconds. Seamless patch
changing is now a reality.
The G2.1u can be powered from four IEC R6 (size AA) batteries or an AC adapter. Continuous operating time on
batteries is approximately 7.5 hours with alkaline batteries.
The expression pedal on the top panel lets you adjust the tonal quality of an effect or the volume in real time.
An optional expression pedal (FP01/FP02) or foot switch (FS01) can be connected to the CONTROL IN jack. The
external expression pedal is used for controlling the volume. The foot switch is convenient for quickly toggling
effect programs or for setting the tempo of the rhythm function.
Please take the time to read this manual carefully so as to get the most out of the unit and to ensure optimum
performance and reliability.
-3-
Specifications
Effect types 54 types
Output Standard stereo phone jack (doubles as line and headphone jack)
Maximum output level Line: +5 dBm (output load impedance 10 kilohms or more)
Phones: 20 mW + 20 mW (into 32 ohms load)
USB interface
PC interface: 16-bit (stereo configuration for recording/playback)
Sampling frequency: 32kHz, 44.1kHz, 48kHz
Power requirements
AC adapter 9V DC, 300 mA (center minus plug) (ZOOM AD-0006)
Batteries Four IEC R6 (size AA) batteries,
Approx. 7.5 hours continuous operation (alkaline batteries)
-5-
BLOCK DIAGRAM
Digital In
Digital Out
1Fs McBSP
64Fs
256Fs
Clock
Foot SW/Ex-Pedal HPI GPIO
Ctrl In
24.576MHz
-6-
+3.3USBV Switch
+5USBV Static Read
PC Linear-Reg. Tact SWx(8+2) 5
(USB BUS) XC6213
Digital Out
Pre Emphasis
ADC
S/N:97dB 1Fs 3.CPU Block
64Fs
+14d
B
CODEC
2.Analog Block AK4552
96kHz
24bit
+6dB
PC
Output De-emphasis
DAC (USB)
S/N:100dB
+6dB
+10dB
De-Emphasis ADC
+10dB
USB CODEC
PCM2904
48kHz
16bit
+0dB
Pre-emphasis
DAC
+0dB
6.USB Block
12MHz
Description of Block Diagram
1. Power supply block
Power supply
AC Adaptor AD-0006 · +3.3 VD for the CPU, DSP, SDRAM, LEDs including the
7-segment LEDs, and peripherals.
· +1.26 VD for the DSP.
· +3.3 VA for the Analog block.
· +8.0 VA for the Analog block.
2. Analog block
1) Guitar input The signal from [INPUT] jack is sent to the DSP and
processed there.
· Rated input level -20 dBm
· Input impedance 1 megohm
· pre-emphasis +16dB in 40kHz or higher
-5
OUTPUT LEVEL(dBm)
-10
-15
-20
-25
-30
10 100 1000 10000 100000
Frequency (Hz)
-8-
4) AD/DA converter:
AK4552VT-E2 Sampling frequency 96 kHz
System Clock (256fs) 24.576 MHz
A/D 2-channel
64-times oversampling
24-bit resolution, MSB justified
D/A 2-channel
128-times oversampling
24-bit resolution, LSB justified
3. CPU block
1) CPU
uPD703015BYGC-A29-8EU 32-bit processing microprocessor
(D163-0003) Internal ROM 128 Kbyte
A/D converter 10-bit resolution, 8-channel
Master clock 20 MHz
2) EEPROM:
M93C86-WMN6 16kbit 3-wire
4) SDRAM
IS42S16100C1-7TL 512 K x 16 bit x 2banks, as external memory of the ZFX-3L
-9-
4. Panel block STATIC KEY (x 7)
STATIC LED (x 5)
DINAMIC LED (x 6)
ROTARY ENCODER (x3)
11 click VOLUME (x1)
7segment LED (x 1)
All LEDs are lit under the control of the CPU.
6. USB block
AK4552VT-E2 Sampling frequency 48 kHz
System Clock 12 MHz
A/D 2-channel
16-Bit Delta-Sigma ADC and DAC
D/A 2-channel
- 10 -
Back Up User’s Data
If necessary, back up the user’s effect patch data to avoid an accidental erasing.
Required
2. Connect “IN” terminal of the transmitter and “OUT” terminal of the receiver.
3. Connect “OUT” terminal of the transmitter and “IN” terminal of the receiver.
4. Connect their ground terminals on the top side of the main PCB, using jumper wires (See
below).
Transmitter Receiver
Main PCB top side Main PCB top side
5. Turn the power of both transmitter and receiver on while holding the [STORE] and the
[RHYTHM] keys.
Make sure that the both 7segment LED lit “tr”.
6. Press the [TYPE -] key of the receiver, and make sure that the 7 segment LED lit “rx”.
The receiver is ready to receive the data.
- 11 -
7. Press the [TYPE +] key of the transmitter and make sure that the 7 segment LED lit “tx”.
The indication flashes on and off at once. And the transmitter starts to send the data.
When sending and receiving finish successfully, and hexadecimals including two dots
such as [x.x.] appears on the display. This displayed [x] depends on User’s patch
conditions.
If [E1] or [E2] or [E3] appear on the display, these mean sending and receiving are error.
In this case, confirm conditions of the transmitter and receiver, and try to back up again.
- 12 -
Function Test
After repairing, the inspection should be performed with the built-in program for inspection.
※ Equipment required
· AC voltage meter (audio analyzer would be better)
· IHF-A filter (audio analyzer might include it)
· Oscillator
· AC adapter (AD-0006)
· Four batteries: R6 [SUM-3] or “AA” size (alkaline batteries are recommended)
· Cables
Turn the [GAIN] dial, and make sure that the [PATTERN] LED lights up.
Turn the [TONE] dial, and make sure that the [TEMPO] LED lights up.
Turn the [LEVEL] dial, and make sure that the [MIX] LED lights up.
And make sure that the indications “01 ->02 -> 03 ... ->Fd ->FE ->FF” appear on the 7segment
LED display when the dial is turned clockwise, and that “FF ->FE ->Fd ... 02 -> 01 -> 00”
when turned anticlockwise.
4. DSP-MUTE check
Press the [TYPE -] key, and make sure that all LEDs go out and output sound is mute.
Press the [TYPE -] key once more, and all LEDs turn on and output sound is emitted.
5. SRAM check
Press the [TYPE +] key, and make sure that the 7segment LED is displayed [2.P] and the delayed
signal is output from the left channel of [OUTPUT] jack.
6. BATTERY check
Press the [STORE] key, and make sure the 7segment LED is displayed the surveillance level of battery
voltage.
- 13 -
7. SWITCH / LED check
Press the [RHYTHM] key, and make sure that the 7segment LED is displayed [r h].
The [RHYTHM] key turn on and off by pressing the [RHYTHM] key.
Press the [TAP] key, and make sure that the 7segment LED is displayed [t P].
The [TAP] key turn on and off by pressing the [TAP] key.
Press the PEDAL ASSIGN key, and make sure that the 7segment LED is displayed [SL].
And make sure that the PEDAL ASSIGN LED turns on in the order of “VOL ->WAH -> DRY ->MOD
->DLY ->REV -> turns off”, whenever the key is pressed.
9. ANALOG-MUTE check
Press the FOOT SWITCH [▼], and make sure that the 7segment LED is displayed as [mt].
The 7segment LED turns on and off by pressing the FOOT SWITCH [▼].
When the 7segment LED turns on, output sound is extremely low.
Press the FOOT SWITCH [▲], and the status of EEPROM is displayed as the following.
[ok]・・・This indication means that default patch data in the EEPROM is correct.
[E0]・・・This indication means that there are some defective soldering on the EEPROM.
[E1]・・・This indication means that patch data in the EEPROM is false.
Make sure that difference between MIN and MAX is 60 or more in hex and this value doesn’t decrease
if EX PEDAL is pressed down.
Make sure that all PEDAL ASSIGN LEDs are turn on and off by pressing down the EX PEDAL
stronger.
- 14 -
11-2. PEDAL setting
Turn on the power holding the PEDAL ASSIGN key, and the indication “dn” appears on the 7segment
LED. With the EP PEDAL fully raised, press the [STORE] key, and the indication “UP” appears on
the 7segment LED.
And the EP PEDAL fully down and then lift your foot off the pedal, then press the [STORE] key.
And the unit returns to the play mode after the indication [Ok] appears the 7segment LED.
After this setting, make sure that the EX PEDAL’s AD value again.
Plug the cable from the expression pedal (FP-01/FP-02) to the [CONTROL IN] jack. Make sure that
the 7segment LED is displayed as range [06] to [09] when the FOOT PEDAL is pressed backward,
and make sure that the 7segment LED is displayed as range [E3] to [FF] when the FOOT PEDAL is
pressed forward.
Plug the cable from the FS-01 to the [CONTROL IN] jack. Make sure that the 7segment LED is
displayed as range [06] to [09] when the FS-01 is turned on, and make sure that the 7segment LED is
displayed as [00] when the FS-01 is turned off.
Set the power supply voltage to 6V. Make sure that the 7segment LED is displayed as [A0] then. And
then set the power supply voltage to 3.9V. Make sure that the 7segment LED is displayed as [bt].
Turn the G2.1u on while holding down the [STORE] key, and the indication “AL” appears on the
7segment LED.
Then press the [STORE] key once more, and All Initialize is carried out.
Press both [▼]/[▲] foot switches together briefly and release, and start the tuner mode and the bypass
state. Make sure that then the 7segment LED is displayed as [bp] and the G2.1u is available as the tuner.
Connect the unit to PC with USB cable and start up USB inspection software.
In the BYPASS mode, Input sin wave (440Hz/-20dBm) to INPUT jack and monitor the waveform on PC.
And output sin wave (440Hz/-20dBm) from PC, monitor the output from OUTPUT jack (L/MONO, R,
Phones) with speakers and oscilloscope.
*Make sure there are no defects (abnormal noise, output trouble, etc…)
*Refer to “How to use USB inspection software” about the how to use inspection software.
After this function test, carry out all initialization (Refer to page 17).
- 15 -
Special Start-up
There are some methods to start up the G2.1u for service.
To start up the unit, set the [POWER] switch to “ON” while holding any keys.
The following table shows which keys are held down.
● Play Mode
Normal operation.
See the operation manual.
● Initialization
● Test Mode
● Data transfer
● Version
● Revision
-16 -
Recovering the Factory Default
In the factory default condition, the patches of the user area (A0-d9) contain the same
settings as the patches of the preset area (00-39). Even after overwriting the user patches,
their original content can be restored in a single operation (“All Initialize” function).
If necessary, back up the user’s patch data. Refer to page 11, 12 for details of the back up.
2. To carry out the All Initialize function, press the [STORE] key once more.
All patch settings are returned to the factory default condition, and the unit switches to
play mode. To cancel All Initialize, press the [RHYTHM] key instead of the [STORE]
key.
- 17 -
G2.1u Circuit Check Specification
s
No. Items Ch Specifications Inputs Conditions/notes Display and Indicator Keys pressed in "Test mode"
1 Current consumption 190mA±20mA (FLASH uPU) Short Immediately after Test mode starts All LEDs are lit. All lit None (Start up)
180mA±20mA (MASK uPU) Short Immediately after Test mode starts All LEDs are lit. All lit None(Start up)
2 Power supply voltage 3.3VA 3.3V±0.15V Short Immediately after Test mode starts All LEDs are lit. All lit None(Start up)
+3.3VD 3.3V±0.15V Short Immediately after Test mode starts All LEDs are lit. All lit None(Start up)
+1.26VD 1.26V±0.05V Short Immediately after Test mode starts All LEDs are lit. All lit None(Start up)
+8VA 8.74V±1.0V Short Immediately after Test mode starts All LEDs are lit. All lit None(Start up)
3 Output level (L) -1.5dBm±1.5dB 440Hz -20dBm Load=32ohms / Output waveform is not clipped. All lit None(Start up)
(Load: 32ohms) (R) -4.5dBm±1.5dB 440Hz ±0dBm Load=32ohms / Output waveform is not clipped. All lit None(Start up)
4 Frequency response (L) +2.5dBm±1.5dB 20Hz -20dBm Output waveform is not clipped. All lit None(Start up)
(No Load) (R) -1.0dBm±1.5dB 20Hz ±0dBm Output waveform is not clipped. All lit None(Start up)
(L) -16.5dBm±1.5dB 20kHz -40dBm Output waveform is not clipped. All lit None(Start up)
(R) -20.0dBm±1.5dB 20kHz -20dBm Output waveform is not clipped. All lit None(Start up)
- 18 -
5 Noise level (L) -80.0dBm or less Short Insert IHF-A All lit None(Start up)
(No Load) (R) -90.0dBm or less Short Insert IHF-A All lit None(Start up)
6 Harmonic distortion (L) 0.1% or less 440Hz -5dBm Delay Mode / Insert 20KHz-LPF. "2.P" "Type+" key(SW5)
(No Load) (R) 0.1% or less 440Hz -5dBm Delay Mode / Insert 20KHz-LPF. "2.P" "Type+" key(SW5)
7 Function of D-MUTE (L) Check function of Mute 440Hz -20dBm Press ”Type-” key and check muting on/off. None ”Type-” key(SW4)
(DSP Mute) (R) Check function of Mute 440Hz -20dBm Press ”Type-” key and check muting on/off. None ”Type-” key(SW4)
8 Function of A-MUTE (L) Check function of Mute 440Hz -20dBm Press ”Down” key and check muting on/off. "mt" "Down" key(SW9)
(Analog Mute) (R) Check function of Mute 440Hz -20dBm Press ”Down” key and check muting on/off. "mt" "Down" key(SW9)
9 Battery warning voltage 4.0V or less (Warning voltage) Make sure that "bt" on display is blinked at 3.9V. "bt" blinked
4.6V or more (released warning) Make sure that the warning is released at 4.7V. Return to normal status
10 Control input Foot sw_OFF 0 FS-01 Make sure that "0" is displayed.
Foot sw_ON 6-9 FS-01 Make sure that value of "6-9" is displayed.
Foot pedal_MIN 6-9 FP-01 Make sure that value of "6-9" is displayed.
Foot pedal_MAX E3-FF FP-01 Make sure that value of "E3-ff" is displayed by hexadecimal.
11 System operation Make sure that keys, dial(11click), knobs, pedals, EEPROM, and LEDs including display and indicator normally operate.
+8VA
C52
R42
CPU
8
13k-F D164_cpu.sch
3 0.1u C92
1
2
D IC7A 100p DSP D
NJM4558M +3.3VA
8
D164_dsp.sch
4
R40 2 C94
1
+
+3.3VA
39k-F
3 Power
IC8A 10u/16V
"GUITAR" D3 NJM2100M D164_pwr.sch
C83 1SS133 R5
4
J2 L4 R3
1
2 5 C84 10k
4 open 7 C54 0.1u DT2A
+
+
1
C88 6
R20 10u/16V D8 R85
2
R41 NJM2100M
3
22k 1SS133 22k
15k-F DT2B
open-c C93
R13 R84 2 DT3 MUN5135DW1T1 +8VA
2
R21 + C91 C23 AMUTE DTC124EKA
7.5k 3 4
C 22k open-c R36 330 C
18p
47u/6.3V 1.3k R43
1
75k-F
C97
0.01u film
5
R22
47k
R24 C73
8.2k
C59 1500p
open-c Q5
R86
+8VA C8
1k
BC817-40LT1G
8
C86 0.1u
+ C96 R26
C56 2 C71
0.1u 2.2u/50V 1 R28
+
+
10u/16V 22k 3 22
IC9A 100u/16V R46
IC15 R9 C98 1k
NJM4556M
+3.3VA 1 16 R45 0.01u
4
B RIN ROUT 22k B
C103 C58 2 15 +8VA
LIN LOUT 1k
+ 10u/16V 0.1u 3 14
VSS VCOM C118 "OUTPUT"
4 13
VA PDN 1000p R11 L5
5 12 open
VD BCLK 22k J3
6 11 2
R35 + C102 C57 DEM0 MCLK
10 7 10
10u/16V 0.1u DEM1 LRCK R44
8 9 3
SDTO SDTI R12 + C61 C22
1k 1
22k open-c Q6 L6
AK4552VT SJ6336
R80 C117 47u/6.3V R87 open
0 1000p
1k
D_IN BC817-40LT1G
D_IN
D_OUT
D_OUT
1FS 5 C72
1FS C87 R29
256FS CN5A 7
+
256FS R27
64FS 6 22
64FS 1 IC9B R47
100u/16V
+
2 22k C99 1k
CODEC_PD- 10u/16V NJM4556M
CODEC_PD- 3 0.01u
R68 C55 4
47k 5 C60
6 R10
to USB PCB
7
A 0.1u A
22k
PH-7A (2mmP) open-c C85
R25 Title
D164 MAIN PCB(PCB-5155) ANALOG circuit 1/7
8.2k
R23
1500p G2.1u CIRCUIT DIAGRAM
Size Number Revision
Z3A-0223-A3
47k MAIN PCB
B (ANALOG) PCB-5155A MP
Date:
File:
14-Dec-2005 Sheet of
C:\Documents and Settings\inoue\ƒfƒXƒNƒgƒbƒv\19-25-G2.1u
Drawn By:
- 19 -
Circuit.ddb
1 2 3 4 5 6
1 2 3 4 5 6 7 8
ECB_GAIN
ECA_GAIN
D +3.3VD D
ECB_TONE
+3.3VD S-80929CNNB-B8P-T2(OPEN) ECA_TONE
+3.3VD IC6 R1
IC4 10k ECB_LEVEL
1 4 1 4 /RESET ECA_LEVEL
VDD OUT VSS OUT R74
2 3 2 3
VSS CD VDD CD 47k
+3.3VD
R3112Q291A C1 R14 R15 R16 R17 R18 R19
0.01u CN10 IC14 +3.3VD 22k 22k 22k 22k 22k 22k
1 8 C2 C4 C6
1 CS VCC
2 7 C19
2 CLK PE
3 6 AVDD +3.3VD
3 DI ORG
4 5 0.039u 0.039u 0.039u
4 DO VSS 0.1u C3 C5 C7 R56
5
IS93C86A-3GRLI open-r
6
For Flash-Writer CN2A
7
8 0.027u 0.027u 0.027u 3 + C67
2 100u/6.3V
11310808-13440000(open) TO VR-PCB
1
LED_GAIN PH-3A(2mmP)
LED_TONE R57
LED_LEVEL open-r
LED_RHYTHM AVSS
LED_TAP +3.3VD
TP1 C11
DEBUG R64 R62 TEST_MODE R30
TP3 D164 47k 47k AVDD
IN 1k
0.01u
TP4 CN3A
OUT
C12 R31 1
TP5 AVSS PEDAL_VAL
GND R63 2
1k TO PEDAL-PCB AVDD
open-r 3
D163 0.01u 4
SW_PEDAL AVSS
5 R53 R54
470k 1k "FOOT-SW/EX-PEDAL"
100
C +3.3VD PH-5A (2mmP) L1 C
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
C13 0 ohm
R32 CONTROL_VAL R51 2 J1
R72 R73 AVDD
P06/INTP5/RTPTRG
1k D6 330k
P07/INTP6
P04/NITP3
P03/INTP2
P02/INTP1
P01/INTP0
P14/SO1/TXD0
P13/SI1/RXD0
P20/SI2
P00/NMI
P81/ANI9
P80/ANI8
P77/ANI7
P76/ANI6
P75/ANI5
P74/ANI4
P73/ANI3
P72/ANI2
P05/INTP4/ADTRG
P12/SCK0/SCL
P10/SI0/SDA
P15/SCK1/ASCK0
P11/SO0
P83/ANI11
P82/ANI10
47k 47k 2 1 R52 3
0.01u
C14 1
R33 1SS133(OPEN) 10k L2
SW_PEDAL from POWER Section 0 ohm SJ6336
BTT_LVL D1
SW_SELECT 1k
AVSS 0.01u 1 C15
1 75 +3.3VD 3 0.1u
P21/SO2 P71/ANI1 L3
2 74 2
P22/SCK2 P70/ANI0
1
+3.3VD 3 73 0 ohm
P23/RXD1 AVREF
5
6
7
8
5
6
7
8
4 72 1SS226(OPEN) AVSS
P24/TXD1 AVSS DT1A
5 71 C18 D7
RA1 RA2 P25/ASCK1 AVDD
0.1u C16 6 70 0.1u 2 MUN5135DW1T1 1 2
47k*4 47k*4 VDD P65/A21
7 69 LED10
VSS P64/A20 1SS133(OPEN)
8 68 LED9 LED_COM1
P26/TI2/TO2 P63/A19
SW_TAP 9 67 LED8
4
3
2
1
4
3
2
1
46
P27/TI3/TO3 P62/A18
10 66 SCAN1
P30/TI00 P61/A17
SW_RHYTHM 11 65 SCAN0
P31/TI01 P60/A16 DT1B
To CN9A 12 IC1 64 1 8
P32/TI10 P57/AD15
SW_STORE 13 uPD703015BYGC-A29-8EU 63 2 7 RA3 5 MUN5135DW1T1
P33/TI11 P56/AD14
SW_TYPEP 14 62 3 6 47k*4
P34/TO0/A13 P55/AD13
SW_TYPEM 15 61 4 5 LED_COM0
P35/TO1/A14 P54/AD12
16 60 1 8 RA4
3
P36/TI4/TO4/A15 P53/AD11
17 59 2 7 47k*4
P37/TI5/TO5 P52/AD10
18 58 3 6 +3.3VD LED[8..10]
IC/VPP P51/AD9
LED0 19 57 4 5
R2 P100/RTP0/A5 P50/AD8
LED1 20 56 C17
0 P101/RTP1/A6 BVSS
LED2 21 55 CN9A
P102/RTP2/A7 BVDD
CN7A LED3 22 54 CPUD7 LED_GAIN 1
P103/RTP3/A8 P47/AD7 20
SW_UP LED4 23 53 0.1u CPUD6 SW_TYPEM 2
1 P104/RTP4/A9 P46/AD6 19
TO FOOTSW-PCB SW_DOWN LED5 24 52 CPUD5 SW_TYPEP 3
2 P105/RTP5/A10 P45/AD5 18
LED6 25 51 CPUD4 SW_STORE 4
3 P106/RTP6/A11 P44/AD4 17
P90/LBEN/WRL
LED7 ECA_GAIN 5
P107/RTP7/A12
P92/R/W/WRH
16
P93/DSTB/RD
PH-3A (2mmP) P95/HLDAK ECB_GAIN 6
P96/HLDRQ
15
P120/WAIT
7
P91/UBEN
P94/ASTB
P114/XT1
14
CLKOUT
P40/AD0
P41/AD1
P42/AD2
P43/AD3
ECA_TONE 8
P110/A1
P111/A2
P112/A3
P113/A4
RESET
13
ECB_TONE 9
VDD
12
XT2
VSS
10
X2
X1
B 11 B
SW_RHYTHM 11 TO PANEL-PCB
10
ECA_LEVEL 12
9
+3.3VD ECB_LEVEL 13
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
8
CN8A 14
7
LED_COM0 SW_TAP 15
1 6
LED_COM1 LED_TONE 16
2 C20 5
LED0 LED_LEVEL 17
3 4
LED1 LED_RHYTHM 18
4 0.1u 3
LED2 LED_TAP 19
5 2
TO 7SEG-PCB LED3 +3.3VD 20
6 1
LED4 CPUD3
7
LED5 C74 CPUD2 11311120-13420000
8
LED6 CPUD1
9
LED7 CPUD0
10 470p
PH-10A (2mmP) CPUD[0..7]
CPUD[0..7]
CODEC_PD-
DSP_RST- X1 PORT_D2C
AMUTE 20MHz PORT_C2D
DSP_HAS-
DSP_HDS-
DSP_R/W-
DSP_RDY
CN4A
1
2
3
A A
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
D D
DSP_RST-
DSP_RST-
CPUD[0..7]
CPUD[0..7]
DSPD10
DSPD11
DSPD12
DSPD13
DSPD14
DSPD15
CPUD0
CPUD1
CPUD2
CPUD3
CPUD4
CPUD5
CPUD6
CPUD7
DSPD0
DSPD1
DSPD2
DSPD3
DSPD4
DSPD5
DSPD6
DSPD7
DSPD8
DSPD9
R67
47k
C75
GPIO7
+3.3VD +1.26VD 470p +1.26VD +3.3VD
0.1u
C24
0.1u
0.1u
0.1u
0.1u
C25
C26
C27
C28
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
VSS
CVDD
CVDD
VSS
VSS
CVDD
VSS
GPIO7
HD0
HD1
HD2
HD3
HD4
HD5
HD6
HD7
TCK
TDI
TRST
DVDD
HPIENA
DVDD
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
RESET
TMS
TDO
EMU1/OFF
EMU0
D10
D11
D12
D13
D14
D15
D16
R65 1 132
GPIO6 D17
47k 2 131
GPIO4 D18
3 130
GPIO2/BOOTM2 VSS
GPIO1 4 129
PORT_C2D GPIO1/BOOTM1 D19
GPIO0 5 128
PORT_D2C GPIO0/BOOTM0 D20
6 127
TIM1 D21
+3.3VD 7 126
R66 TIM0 D22
8 125 C35
INT0 D23
47k C29 9 124
CVDD DVDD open-c
0.1u 10 123
INT1 D24
C 11 122 C
INT2 D25 C32
C30 12 121
DVDD CVDD
0.1u 13 120
INT3 D26
14 119 0.1u
NMI/WDTOUT D27
15 118
IACK D28
16 117 DSPD[0..15]
VSS VSS
17 116
CLKR0 D29
+3.3VD +3.3VD 18 115
DR0 D30
19 IC2 114
FSR0 D31 C34 0.1u
20 ZFX-3 113 +3.3VD +3.3VD
R70 R71 CLKX0 CVDD
C31 21 112 DSPA2
47k 47k CVDD A2
0.1u 22 111 DSPA3 IC3
DX0 A3 C36
23 110 DSPA4 1 50
FSX0 A4 VCC GND
64FS R77 0 24 109 DSPD15 0.1u 2 49 DSPD0
64FS CLKR1 VSS I/O0 I/O15
D_IN 25 108 DSPA5 DSPD14 3 48 DSPD1
D_IN DR1 A5 I/O1 I/O14
1FS R78 0 26 107 DSPA6 4 47
1FS FSR1 A6 GNDQ GNDQ
D_OUT R79 0 27 106 DSPA7 DSPD13 5 46 DSPD2
D_OUT DX1 A7 C33 I/O2 I/O13
28 105 DSPD12 6 45 DSPD3
R69 CLKX1 DVDD I/O3 I/O12
29 104 0.1u DSPA8 C37 7 44 C40
47k VSS A8 VCCQ VCCQ
30 103 DSPA9 DSPD11 0.1u 8 43 0.1u DSPD4
FSX1 A9 I/O4 I/O11
31 102 DSPA10 DSPD10 9 42 DSPD5
TEST A10 I/O5 I/O10
32 101 DSPA11 10 41
NC A11 C48 GNDQ GNDQ
C43 33 100 DSPD9 11 40 DSPD6
CVDD CVDD I/O6 I/O9
0.1u 34 99 0.1u DSPA12 DSPD8 12 39 DSPD7
RX A12 I/O7 I/O8
35 98 DSPA13 C38 13 38 C41
GPIO5 A13 VCCQ VCCQ
C42 36 97 DSP_BE1 0.1u 14 37 0.1u
256FS DVDD VSS LDQM NC
0.1u 37 96 /DSP_WE 15 36 DSP_BE0
TX A14 WE UDQM
38 95 /DSP_CAS 16 35 DSP_SDCLK
GPIO3 A15 C49 CAS CLK
39 94 /DSP_RAS 17 34 DSP_SDCKE
VSS DVDD RAS CKE R83
40 93 0.1u /DSP_CE0 18 33
SCL A16 CS NC open-r
41 92 DSPA13 19 32 DSPA11
SDA A17 A11 A9
C1/AOE/SDRAS
C0/ARE/SDCAS
CPUD1 42 91 DSPA12 20 31 DSPA10
C2/AWE/SDWE
HC1/HBIL VSS A10 A8
DSP_HAS- 43 90 DSPA2 21 30 DSPA9
C15/HOLDA
HC0/HAS A18 A0 A7
C12/SDCKE
ECLKOUT2
ECLKOUT1
EMIFCLKS
C14/HOLD
44 89 DSPA3 22 29 DSPA8
X2/CLKIN
C13/SOE3
C3/ARDY
HCS A19 A1 A6
CLKOUT
HCNTL1
HCNTL0
C11/BE3
C10/BE2
ECLKIN
DSPA4 23 28 DSPA7
C9/BE1
C8/BE0
C7/CE3
C6/CE2
C5/CE1
C4/CE0
DVDD A2 A5
DVDD
CVDD
HRDY
CVDD
PVDD
HR/W
HDS2
HDS1
DSPA5 24 27 DSPA6
HINT
A3 A4
VSS
VSS
VSS
VSS
VSS
A21
A20
NC
XF C39 25 26
X1
VCC GND
0.1u
IS42S16100C1-7TL
B B
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
DSPA[2..13]
C46
0.1u
0.1u
C44
C47
0.1u
CPUD3
C45
CPUD2 C51
0.1u
0.1u
EMI
DSP_TX
DSP_HAS- R81
DSP_R/W- /DSP_CAS
DSP_R/W- 0
DSP_HDS- /DSP_RAS
DSP_HDS-
DSP_RDY
DSP_RDY
/DSP_WE
TP2
+3.3VD L13 VDD_PLL DSP_TX /DSP_CE0
BLM18AG102S DSP_SDCLK need GND guard pattern
DSP_SDCLK
+ C80
10u/16V DSP_BE0
DSP_BE1
A +3.3VD A
14
C50 0.1u
IC5F
GND
13 12
G2.1u CIRCUIT DIAGRAM
VCC
SN74HCU04ANS
7
MAIN PCBD164
(DSP) PCB-5155
MAIN PCB(PCB-5155)
Title
ANALOG circuit 1/7
D164 MAIN PCB(PCB-5155) DSP circuit 4/7
Size Number Revision
Z3A-0223-A3 MP
A2 Z3A-0223-A3
Date:
File:
28-Dec-2005 Sheet of - 21 -
\\Server\PAT\‹Z p•”\Service Manual\G2.1u\Œ³ƒlƒ^\19-25-G2.1u
Drawn By:
MP
Circuit.ddb
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
C
3
CN2B
SW1 SW2 SW3
3
2 RE160-40E3 RE160-40E3 RE160-40E3
2
D +3.3VD +3.3VD +3.3VD COM1 D
1
VR1 COM2
B
A
A
PH-3Y 2651#26/L=120MM R214 R216 R218
1
RK0971110S0NB 2.2k(7.5mm) 2.2k(7.5mm) 2.2k(7.5mm)
R215 R217 R219
2.2k(7.5mm) 2.2k(7.5mm) 2.2k(7.5mm) ECA_LEVEL R205 1k (7.5mm) LED5
VR-PCB PCB-5159 ECB_LEVEL R200 1k (7.5mm) LED0
ECA_TONE R201 1k (7.5mm) LED1
ECB_TONE
18
17
16
15
14
13
12
11
10
ECA_GAIN SEG1
ECB_GAIN E20561-GFOR
+3.3VD
1F
2F
com1
com2
1G
1A
2A
1B
2B
1A 2A
LED1 LED2 LED3
KSNR-312N-30 KSNR-312N-30 KSNR-312N-30 1B
JP202 1F 2B
1G 2F 2G
Wire(7.5mm)
GAIN TONE LEVEL 1E 1C 2C
2E
JP200 JP201
Wire(7.5mm) Wire(7.5mm) 1D 1dp 2D 2dp
1dp
2dp
R208 R209 R210
1D
2D
2G
1C
2C
1E
2E
3.3k (7.5mm) 3.3k 3.3k
LED_LEVEL
LED_TONE
1
2
3
4
5
6
7
8
9
C LED_GAIN R207 1k (7.5mm) LED7 C
R202 1k (7.5mm) LED2
R206 1k (7.5mm) LED6
R203 1k (7.5mm) LED3
R204 1k (7.5mm) LED4
10
9
8
7
6
5
4
3
2
1
SW_TAP
SW_RHYTHM CN8B
SW_STORE 7SEG-PCB PCB-5157 PH-10Y 2651#26/L=80MM
SW_TYPEP
SW_TYPEM
+3.3VD
A
LED4 LED5
2 1
2 3
SW_STORE
3 R212 R213 4
B ECA_GAIN B
1k (7.5mm) 1k (7.5mm) 5
ECB_GAIN
6
LED_TAP
7
LED_RHYTHM ECA_TONE
8
ECB_TONE
9
DOWN UP 10
SW9 SW10 SW_RHYTHM
11
ECA_LEVEL
12
1104RTA-2 1104RTA-2 ECB_LEVEL
13
14
SW_TAP
15
LED_TONE
16
LED_LEVEL
17
LED_RHYTHM
FOOTSW-PCB 18
PCB-5158 LED_TAP
19
+3.3VD
20
20FMZ-ST
A A
Title
G2.1u CIRCUIT DIAGRAM
PANEL PCB (PANEL) PCB-5156
Size
A3
Number Revision
USB-Audio
D164CS_USB.SCH
D D
LED/SW LED400
VOL
PCB-5161
SUNR-063 (Rank10,11)
LED401
WAH
SUNR-063 (Rank10,11)
LED402
DRV
C C
AVDD
3
SUNR-063 (Rank10,11) RH0411CS2J
LED403 VR400
MOD 2
R400 LED8 C401
1k
SUNR-063 (Rank10,11) AVDD
1
LED404 AVDD OPEN-C
DLY R403
R401 LED9 IC401 R405 + C403 From MAIN-PCB
110k open-c
1 4 CN400B CN400A 330 R404
1k
SUNR-063 (Rank10,11) 110k IC400B CN3B
3 3
LED405 2 3 6
2 2 1
REV 1 1
7 PEDAL
2
R402 LED10 AVDD 5
NJL5167KB 3
1k PH-3A (2mmP)
SUNR-063 (Rank10,11) 4
ZH-0065:3Pin 2mmPich L=50mm NJM2100M
R406 5
AVSS AVSS
B
PHOTO 10K ZH-0067:5Pin 2mmPich L=70mm
B
PCB-5162
From MAIN-PCB PEDAL
R407 C400
CN4B 10K open-c
LED_COM0 AVDD C402 SW401
1
LED_COM1 1104RTA-2
2
8
LED8 AVSS
3 0.1u
LED9
4
LED10 2
5
1
6
SW_SELECT 3
7 IC400A
ZH-0069:7Pin 2mmPich L=80mm SELECT NJM2100M
4
SW400
1104RTA-2 AVSS
Title
A A
G2.1u CIRCUIT DIAGRAM
Size Number Revision
USB
A4
PCB (PEDAL) PCB-5160
Date: 14-Dec-2005 Sheet of
File: D164MP_pedal.sch
C:\Documents and Settings\inoue\ƒfƒXƒNƒgƒbƒv\19-25-G2.1u
Drawn By: - 23
Circuit.ddb -
1 2 3 4
1 2 3 4
SW15A
1
D R48 D
2 110k-F 120mA max
CN6A 3 +3.3VD
BTT_LVL
USB_VBUS HSW2202-010020
1 R49 L9
2 22k-F
USB_GND SW15B open
PH-2A (2mmP) 4
5 + C69
6 open-c
HSW2202-010020 30mA max
"DC-IN" AD-0006 L14 uPC29M33AT/NJM2885DL1-33 +3.3VA
Wire 5mm(ZBF503D-00) C62 IC10
J6 L7
2 1 3
Vin +3.3V
0 ohm
GND
3 C100 0.1u C63 C64
0.1u C68 + + C70
1 C21 C108 + 0.1u 0.1u open-c
0.1u open-c 100u/6.3V L8
2
SK22H09-G9 C101 0 ohm
0.1u
C D2 R76 C
1 2
CN1 3.3 2W
L15 1N4003
BATT+ Wire 5mm(ZBF503D-00)
1
2
BATT-
PH-2A (2mmP)
D4 LQH43CN220K03 LQH43CN220K03
40mA max +8VA Q2 RB160L-40TE25 L10 Q4 +1.26VD
L11 L12
BC817-40 2SB1706 300mA max
22uH 22uH open
+ C109 R8
C10
Q3 470u/16V
R34 470 2200p
BC817-40 R7
R6 C9 1k D5
1k
2.2k 2200p RB160L-40TE25
R55
B R58 C111 100 C112 R60 B
150k 100p IC11 100p
+ C89 + C110 C65 1 10 120k-F C66 + C113 + C114
100u/16V 0.1u EXT1 EXT2 0.1u 470u/16V open-c
2 9
470u/16V VDD GND
3 8
FB1 FB2
4 7
PWM1 PWM2
5 6
R59 EN1 EN2 R61
16k + C81 R75 XC9502B093AR 300k-F
10u/16V 1K
Title
A A
G2.1u CIRCUIT DIAGRAM
Size Number Revision
MAIN
A4
PCB (POWER) PCB-5155A
Date: 14-Dec-2005 Sheet of
File: D164MP_power.sch
C:\Documents and Settings\inoue\ƒfƒXƒNƒgƒbƒv\19-25-G2.1u
Drawn By: - 24
Circuit.ddb -
1 2 3 4
1 2 3 4 5 6 7 8
FGND FGND
GND
VCC
FG FG
D+
D-
FGND FGND
1
2
3
4
+5USBV IC503 +3.3V
1 5
Vin Vout
R502
USB D+
+ C529 + C532
USB D-
C530 2 C531
10u/16V 0.1u GND 0.1u 10u/16V
68k
R501 C503 3 4
CE NC
12k XC6213B332MR
C501 1000p
R503
open-c DT500
1.5k DTC124EKA
3
+3.3V C502 IC502
R505 22 1 28 C505 SSPND 2
D+ SSPND
8
R504 22 2 27
C500 D- VDDI
R500 0.1u 3 26
C C504 VBUS DGND C
2 4 25 1u
DGNDU TEST1
1 5 24 C519
1
22k HID0 TEST0
10u/16V NP 3 6 23
+
IC500A HID1 VCCXI
VCOM open 7 22
HID2 AGNDX
NJM2100M 8 21 1u for OUTPUT OPAMP
SEL0 XTI C521 R521
+3.3V 9 20 +5VO
4
SEL1 XTO 1K
10 19 +5USBV
VCCCI VCCP2I R522
11 18 C520
C515 AGNDC AGNDP + C535
5 12 17 1u 10K
C512 VINL VCCP1I 470u/6.3V
7 13 16 Q501
R510 VINR VOURL
3
6 14 15 1u BC807-40
+
IC500B VCOM VOUTR R518
open VCOM
22k PCM2904DBR 220 CN6B
10u/16V NP NJM2100M R513 6 USB_VBUS
C513 + 1
1M 4 5
C516 R523 2
2 USB_GND
0.1u C517 C518 X500 1 ZH-0066:2Pin 2mmPich L=200mm
0.1u 2.7 1/4W
open-c C514 47u/6.3V 12MHz
CN5B R511 R524
Q500
1 12k 2.7 1/4W NTGS3441T1
1000p C522 C523
2 R512 18p 18p
3
to MAIN PCB 68k
4
5
6
7 R509
B ZH-0068:7Pin 2mmPich L=200mm 47k B
C510
47p
C509 +5VO
R508
8
47k
0.1u C508 C506
C511 2 R507 R506
+
1 8.2k 1k
3 1500p C507 open
10u/16V NP IC501A VCOM 2200p
NJM2100M
4
C528 5
7 C526 C524
6 R515 R514
+
10u/16V NP IC501B
8.2k 1k
NJM2100M 1500p C525 open
R516 2200p
C527
47k
47p
R517
A 47k A
Title
G2.1u CIRCUIT DIAGRM
USB PCB (USB) PCB-5160
Size
A3
Number Revision
1
VR PCB: soldered
3
ZH-0060 Flat Cable:
B3B-PH-K-S(JST)
2mm-pitch 3pin
80 mm
Main PCB
1
SW PCB: soldered
3
Flat Cable:
B3B-PH-K-S(JST) ZH-0061
2mm-pitch 3pin
80 mm
Main PCB
1
10
B10B-PH-K-S(JST)
ZH-0062 Flat Cable:
2mm-pitch 10pin
80 mm
Main PCB Pannel PCB
reinforcing board on back side
1 1
20 20
ZH-0063 SUMI CARD 1mm-pitch 20pin FMN Connectpor (DIP type)
11311220-134200000(DNS)
200 mm
Main PCB
1 Battery turminal:
2 soldered
1Pin:AWG24(Red)
B2B-PH-K-S(JST) ZH-0064
2Pin:AWG24(Black)
- 26 -
USB PCB 50 mm
1 PHOTO PCB:
soldered
3
ZH-0065 Flat Cable:
B3B-PH-K-S(JST)
2mm-pitch 3pin
70 mm
Main PCB
1
USB PCB: soldered
5
Flat Cable:
ZH-0067
B3B-PH-K-S(JST) 2mm-pitch 5pin
200 mm
Main PCB
1
B10B-PH-K-S(JST)
ZH-0068 Flat Cable:
2mm-pitch 7pin
80 mm
Main PCB
1
B10B-PH-K-S(JST)
ZH-0069 Flat Cable:
2mm-pitch 7pin
200 mm
Main PCB
1
USB PCB: soldered
2
1Pin:AWG24(Red)
B2B-PH-K-S(JST) ZH-0066
2Pin:AWG24(Black)
- 27 -
IC Pin Assignment
*Common IC with the G2
*CPU *EEPROM
/uPD703015BGC-A29-8EU /IS93C86A-3GRLI
/NEC /ISSI
/100P LQFP /8P SOP
/IC1 100
99 /IC14
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
1 CS VCC 8
P06/INTP5/RTPTRG
P07/INTP6
P04/NITP3
P03/INTP2
P02/INTP1
P01/INTP0
P20/SI2
P14/SO1/TXD0
P13/SI1/RXD0
P00/NMI
P81/ANI9
P80/ANI8
P77/ANI7
P76/ANI6
P75/ANI5
P74/ANI4
P73/ANI3
P72/ANI2
P12/SCK0/SCL
P05/INTP4/ADTRG
P15/SCK1/ASCK0
P11/SO0
P10/SI0/SDA
P83/ANI11
P82/ANI10
2 CLK PE 7
3 DI ORG 6
4 DO VSS 5
1 75
P21/SO2 P71/ANI1
2 74
P22/SCK2 P70/ANI0
3 73
P23/RXD1 AVREF
4 72
P24/TXD1 AVSS
5 71
6
7
P25/ASCK1
VDD
AVDD
P65/A21
70
69
*Reset IC
VSS P64/A20
8
9
P26/TI2/TO2
P27/TI3/TO3
P63/A19
P62/A18
68
67 /R3112Q291A-TR
10 66
11
12
P30/TI00
P31/TI01
P61/A17
P60/A16
65
64
/Ricoh
P32/TI10 P57/AD15
/4P SC-82
13 63
P33/TI11 P56/AD14
14 62
P34/TO0/A13 P55/AD13
15 61
P35/TO1/A14 P54/AD12
16
17
P36/TI4/TO4/A15
P37/TI5/TO5
P53/AD11
P52/AD10
60
59 /IC4
18 58
IC/VPP P51/AD9
19 57
P100/RTP0/A5 P50/AD8
20 56
P101/RTP1/A6 BVSS
21
P102/RTP2/A7 BVDD
55 2 VDD OUT 1
22 54
23
P103/RTP3/A8
P104/RTP4/A9
P47/AD7
P46/AD6
53 4 VSS CD 3
24 52
P105/RTP5/A10 P45/AD5
25 51
P106/RTP6/A11 P44/AD4
P90/LBEN/WRL
P107/RTP7/A12
P92/R/W/WRH
P93/DSTB/RD
P95/HLDAK
P96/HLDRQ
P120/WAIT
P91/UBEN
P94/ASTB
P114/XT1
CLKOUT
P40/AD0
P41/AD1
P42/AD2
P43/AD3
P110/A1
P111/A2
P112/A3
P113/A4
RESET
VDD
*Voltage Regulator
XT2
VSS
X2
X1
/uPC29M33AT-E1
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
*DSP /NEC
/ZFX-3(1.26V, 3.3V) /SC63
/ZOOM /IC10
/176P LQFP
/IC2 1 Vin GNG +3.3V 3
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
VSS
VSS
VSS
VSS
CVDD
GPIO7
HD0
HD1
HD2
CVDD
HD3
HD4
HD5
HD6
CVDD
HD7
TCK
TDI
TRST
DVDD
HPIENA
DVDD
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
RESET
TMS
TDO
EMU1/OFF
EMU0
D10
D11
D12
D13
D14
D15
D16
1 132
GPIO6 D17
2 131
GPIO4 D18
3 130
*SDRAM
GPIO2/BOOTM2 VSS
4 129
GPIO1/BOOTM1 D19
5 128
GPIO0/BOOTM0 D20
6 127
7
8
TIM1
TIM0
D21
D22
126
125
/IS42S16100C1-7TL
INT0 D23
9
10
CVDD
INT1
DVDD
D24
124
123 /ISSI
11 122
/50P TSOP
INT2 D25
12 121
DVDD CVDD
13 120
INT3 D26
14 119
15
16
NMI/WDTOUT
IACK
D27
D28
118
117
/IC3
VSS VSS
17 116
CLKR0 D29
18 115
DR0 D30 1 50
19 114 VCC GND
FSR0 D31
20 113 2 49
21
CLKX0 CVDD
112 I/O0 I/O15
CVDD A2 3 48
22 111 I/O1 I/O14
DX0 A3 4 47
23 110 GNDQ GNDQ
24
FSX0 A4
109 5 46
CLKR1 VSS I/O2 I/O13
25 108 6 45
DR1 A5 I/O3 I/O12
26
FSR1 A6
107 7 44
27 106 VCCQ VCCQ
DX1 A7 8 43
28 105 I/O4 I/O11
CLKX1 DVDD 9 42
29
VSS A8
104 I/O5 I/O10
30 103 10 41
FSX1 A9 GNDQ GNDQ
31 102 11 40
32
TEST A10
101 I/O6 I/O9
NC A11 12 39
33 100 I/O7 I/O8
CVDD CVDD 13 38
34 99 VCCQ VCCQ
35
RX A12
98 14 37
GPIO5 A13 LDQM NC
36 97 15 36
DVDD VSS WE UDQM
37
TX A14
96 16 35
38 95 CAS CLK
GPIO3 A15 17 34
39 94 RAS CKE
VSS DVDD 18 33
40
SCL A16
93 CS NC
41 92 19 32
SDA A17 A11 A9
42 91 20 31
C1/AOE/SDRAS
C0/ARE/SDCAS
C2/AWE/SDWE
43
HC1/HBIL VSS
90 A10 A8
HC0/HAS A18 21 30
C15/HOLDA
A0 A7
C12/SDCKE
ECLKOUT2
ECLKOUT1
44 89
EMIFCLKS
C14/HOLD
22 29
X2/CLKIN
HCS A19
C13/SOE3
C3/ARDY
CLKOUT
A1 A6
HCNTL1
HCNTL0
C11/BE3
C10/BE2
ECLKIN
23 28
C9/BE1
C8/BE0
C7/CE3
C6/CE2
C5/CE1
C4/CE0
DVDD
DVDD
CVDD
HRDY
CVDD
PVDD
A2 A5
HR/W
HDS2
HDS1
HINT
24 27
VSS
VSS
VSS
VSS
VSS
A21
A20
NC
XF
A3 A4
X1
25 26
VCC GND
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
- 28 -
23$03,&
$.97( 1-007( 1-007( 1-007(
$.0 -5& -5& -5&
376623 3623 3623 3623
,& ,& ,& ,&
1 4
1 5,1 5287 287 9
2 /,1 /287
3 966 9&20 2 7
,1 287
4 9$ 3'1
5 9' %&/.
7 '(0 /5&.
8 6'72 6'7,
9 4 5 ,1
VHJPHQW/('
(*)25
/RJLF,& .LQGZLQ
61+&8$16 3',3
7H[DV,QVWUXPHQWV
3623 6(*
18
17
16
15
14
13
12
11
10
,&
1F
2F
com1
com2
1G
1A
2A
1B
2B
1A 2A
1 14 1B
1F 2B
VCC 1G 2F 2G
13 1E 1C 2C
2E
2 1D 1dp 2D 2dp
3
1dp
2dp
1D
2D
2G
1C
2C
1E
2E
12
11
1
2
3
4
5
6
7
8
9
4
5 'LJ&20021$12'(3,112
10
9
6 A B C D E F G dp
16 15 3 2 1 18 17 4
7 8
GND
'LJ&20021$12'(3,112
A B C D E F G dp
11 10 8 6 5 12 7 9
- 29 -
'&'&&RQYHUWHU
7UDQVLVWRU
725(; ,QILQHRQ
;&%$5 %&313
30623 6&
,& 4
1 EXT1 EXT2 10
2 VDD GND 9 %
3 FB1 FB2 8
$ '
4 PWM1 PWM2 7
5 EN1 EN2 6
,QILQHRQ
'7UDQVLVWRU %&131
216(0, 6&
081':7 4444
6&
'7'7
%
$ '
'LRGH
52+0 5(&7521
667 1
3LWFK PP 3LFWK PP
'' '
&DWKRGH0DUN
52+0
'7&(.$
6&
'7
&KLS6KRWWN\'LRGH
176
52+0
)0&
5%/7(
+0
30'6
''
&DWKRGH0DUN
-30-
Added IC for G2.1u
*USB Codec *Digital Transistor
/Texas Instruments /ROHM
/PCM2904 /DTC124EKA
/28P SSOP /SC59
/IC502 /DT3
1 D+ SSPND 28 OUT
2 D– VDDI 27 3
3 VBUS DGND 26
4 DGNDU TEST1 25
5 HID0 TEST0 24
6 HID1 VCCXI 23
7 HID2 AGNDX 22 1
2
8 SEL0 XTI 21
9 SEL1 20 IN GND
XTO
10 VCCCI VCCP2I 19
11 AGNDC AGNDP 18
12 VINL VCCP1I 17
13 VINR VOUTL 16 *FET
14 VCOM VOUTR 15 /Onsemi
/NTGS3441T1
/TSOP-6pin
*Photo Reflector /Q500
/JRC
/NJL5167KB D D S
/4P DIP 6 5 4 D : Drain
/IC401 S : Source
1 : anode G : Gate
1 2 3
1 3 2 : emitter D D G
3 : collector
2 4 4 : cathode
*Chip LED
/Kindwin
*Voltage Regulator /SUNR-063
/TOREX /1608
/XC6213B332MR /LED400 - LED405
/SOT-23-5
/IC503
Back View
VOUT NC
5 4
Polarity Mark
1 2 3
VIN VSS CE
-31-
PCB-5157 PCB-5158
Top Layer Top Layer
- 34 -
- 36 -
Parts List
ELECTRONIC PARTS LIST
Main PCB PCB-5155A
No. NAME SPECIFICATIONS DESCRIPTION REFERENCE No. Q'ty
1 MPU uPD703015BGC-A29-8EU LQFP-100pin Built in mask ROM for G2/4 (163-0002) IC1 1
2 DSP ZFX-3 LQFP-176pin IC2 1
3 SDRAM IS42S16100C1-7TL TSOP-50pin IC3 1
EM636165TS-7G TSOP-50pin IC3 0
K4S161622H-UC60 TSOP-50pin IC3 0
4 AD/DA AK4552VT-E2 TSSOP-16pin IC15 1
5 EEPROM IS93C86A-3GRLI SOP-8pin 16kbit IC14 1
M93C86-WMN6P SOP-8pin 16kbit IC14 0
S93C86BD4H-J8V2 SOP-8pin 16kbit IC14 0
6 Logic IC SN74HCU04ANS SOP-14pin IC5 1
SN74HCU04DR SOIC-14pin IC5 0
MC74HCU4ADR SOIC-14pin IC5 0
SN74LVU04ANSR SOP-14pin IC5 0
SN74HCU04NSR SOP-14pin IC5 0
7 OPAMP NJM2100M-TE1 SOP-8pin IC8 1
8 OPAMP NJM4558M-TE1 SOP-8pin IC7 1
9 OPAMP NJM4556M-TE1 SOP-8pin IC9 1
10 Voltage Regulator uPC29M33AT-E1 SC63 IC10 1
NJM2885DL1-33-TE1 SC63 IC10 0
11 DC-DC Converter XC9502B093AR MSOP-10pin IC11 1
12 Reset-IC R3112Q291A-TR SC82 2.9V IC4 1
S-80929CNNB-B8P-T2 SC82 2.9V IC6 0
13 D-Transistor MUN5135DW1T1 SC88 DT1 DT2 2
UMB10N SC88 DT1 DT2 0
14 D-Transistor DTC-124EKA SC59 DT3 1
MUN2212T1G SC59 DT3 0
15 Transistor 2SB1706 SC59 Q4 1
16 Transistor BC817-40LT1G SC59 Q2 Q3 Q5 Q6 4
2SD1781K SC59 Q2 Q3 Q5 Q6 0
BC817-40 SC59 Q2 Q3 Q5 Q6 0
2SD596 SC59 Q2 Q3 Q5 Q6 0
17 Diode 1N4003 Pitch=7.5mm D2 1
18 Diode 1SS133T-77 Pitch=7.5mm D3 D8 2
19 OPEN (Unmounting) Pitch=7.5mm D6 D7 0
20 OPEN (Unmounting) SC59 D1 0
21 Chip Shottky Diode RB160L-40TE25 SMD D4 D5 2
MBRS130LT3 SMD D4 D5 0
MBRS140T3 SBD D4 D5 0
22 Ceramic Oscillator EFOMC2005T4 20MHz Built in capacitor X1 1
CSTLS20M0X53-A0 20MHz Built in capacitor X1 0
23 Crystal Oscillator HC49U/S3 24.576MHz X2 1
HC49U/S 24.576MHz X2 0
24 Chip Inductor LQH43CN220K03 SMD 4532 L10 L11 2
25 Chip Inductor BLM18AG102SN1 1608(0603) L13 1
26 OPEN (Unmounting) OPEN-L(Chip Inductor) L4 L5 L6 L9 L12 0
27 OPEN (Unmounting) OPEN-C D=4.0mm H=7.0-11.5mm Pitch=5mm C69 C70 C108 C114 0
28 Capacitor 0.1u/50V D=4.0mm H=7.0-11.5mm Pitch=5mm C83 1
29 Capacitor 2.2u/50V D=4.0mm H=7.0-11.5mm Pitch=5mm C96 1
C86 C87 C94 C95 C102
30 Capacitor 10u/16V D=4.0mm H=7.0-11.5mm Pitch=5mm 8
C103 C80 C81
31 Capacitor 47u/6.3V (10V) D=4.0-6.3mm H=7.0-11.5mm Pitch=5mm C61 C90 C91 3
32 Capacitor 100u/6.3V (16V) D=4.0-6.3mm H=7.0-11.5mm Pitch=5mm C67 C68 C71 C72 C84 5
33 Capacitor 100u/16V D=4.0-6.3mm H=7.0-11.5mm Pitch=5mm C89 1
34 Capacitor 470u/16V D=8mm H=11.5mm Pitch=3.5mm C109 C110 C113 3
35 Film Capacitor 0.01u-J 100V (50V) Radial Pitch=5mm C97 1
C22 C23 C35 C53 C59
36 OPEN (Unmounting) OPEN-C(Chip Inductor) 1608(0603) 0
C60 C76 C77 C88
37 Chip Capacitor 10p-D CH 50V (25V) 1608(0603) C82 1
38 Chip Capacitor 15p-J CH 50V (25V) 1608(0603) C78 C79 2
39 Chip Capacitor 18p-J CH 50V (25V) 1608(0603) C93 1
40 Chip Capacitor 100p-J CH 50V (25V) 1608(0603) C111 C112 C92 3
41 Chip Capacitor 470p-J CH 50V (25V) 1608(0603) C74 C75 2
42 Chip Capacitor 1000p-K B 50V (25V) 1608(0603) C117 C118 2
43 Chip Capacitor 1500p-K B 50V (25V) 1608(0603) C73 C85 2
44 Chip Capacitor 2200p-K B 50V (25V) 1608(0603) C9 C10 2
C1 C11 C12 C13 C14
45 Chip Capacitor 0.01u-K B 16V 1608(0603) 7
C98 C99
46 Chip Capacitor 0.027u-K B 16V 1608(0603) C3 C5 C7 3
47 Chip Capacitor 0.039u-K B 16V 1608(0603) C2 C4 C6 3
C8 C15 C16 C17 C18
C19 C20 C21 C24 C25
C26 C27 C28 C29 C30
C31 C32 C33 C34 C36
C37 C38 C39 C40 C41
48 Chip Capacitor 0.1u-Z F 25V 1608(0603) 48
C42 C43 C44 C45 C46
C47 C48 C49 C50 C51
C52 C54 C55 C56 C57
C58 C62 C63 C64 C65
C66 C100 C101
49 Resistor 3.3-J 2W MOF Lead-form: Floated type pitch=15mm R76 1
50 OPEN (Unmounting) open-r 1608(0603) R56 R57 R63 R83 0
R2 R77 R78 R79 R80
51 Chip Resistor 0 ohm 1608(0603) R81 R82 L1 L2 L3 12
L7 L8
52 Chip Resistor 10-J 1608(0603) R35 1
53 Chip Resistor 22-J 1608(0603) R28 R29 2
54 Chip Resistor 100-J 1608(0603) R55 1
55 Chip Resistor 220-J 1608(0603) R50 1
- 37 -
56 Chip Resistor 330-J 1608(0603) R84 1
57 Chip Resistor 470-J 1608(0603) R8 1
58 Chip Resistor 620-J 1608(0603) R39 1
R7 R30 R31 R32 R33
59 Chip Resistor 1k-J 1608(0603) R34 R44 R45 R46 R47 14
R54 R75 R86 R87
60 Chip Resistor 1.3k-J 1608(0603) R36 1
61 Chip Resistor 2.2k-J 1608(0603) R6 1
62 Chip Resistor 7.5k-J 1608(0603) R13 1
63 Chip Resistor 8.2k-J 1608(0603) R24 R25 2
64 Chip Resistor 10k-J 1608(0603) R1 R3 R4 R5 R52 5
65 Chip Resistor 13k-F 1608(0603) R42 1
66 Chip Resistor 15k-F 1608(0603) R41 1
67 Chip Resistor 16k-J 1608(0603) R59 1
R9 R10 R11 R12 R14
68 Chip Resistor 22k-J 1608(0603) R15 R16 R17 R18 R19 15
R20 R21 R26 R27 R85
69 Chip Resistor 22k-F 1608(0603) R49 1
70 Chip Resistor 39k-F 1608(0603) R40 1
R22 R23 R62 R64 R65
71 Chip Resistor 47k-J 1608(0603) R66 R67 R68 R69 R70 14
R71 R72 R73 R74
72 Chip Resistor 75k-F 1608(0603) R43 1
73 Chip Resistor 110k-F 1608(0603) R48 1
74 Chip Resistor 120k-F 1608(0603) R60 1
75 Chip Resistor 150k-J 1608(0603) R58 1
76 Chip Resistor 300k-F 1608(0603) R61 1
77 Chip Resistor 330k-J 1608(0603) R51 1
78 Chip Resistor 470k-J 1608(0603) R53 1
79 Chip Resistor 1M-J 1608(0603) R37 R38 2
80 Resistor Network 47k*4-J RAC1608 4Element RA1 RA2 RA3 RA4 4
81 Wire Jumper Φ0.5 Pitch=5mm L14 L15 2
82 Stereo Phone Jack SJ6336 with Nut/Washer J1 J3 2
HTJ-064-12D with Nut/Washer J1 J3 0
83 Phone Jack SJ6335 with Nut/Washer J2 1
HTJ-064-12I with Nut/Washer J2 0
84 DC Jack DC-05G Φ2.0 J6 1
DC-208 J6 0
HEC2305-01-250 J6 0
SCD438CCS033000 J6 0
85 Slide SW SK22H09-G9 Length of lever=9mm SW15 1
SSH-2H19-G9 Length of lever=9mm SW15 0
HSW2022-010020 Length of lever=9mm SW15 0
SK22H04-G 9 NS Length of lever=9mm SW15 0
86 FPC Connector 11311120-13420000 20pin To Panel PCB DIP 180deg CN9A 1
20FMZ-ST 20pin To Panel PCB Right angle CN9A 0
87 Connector PH10A 10pin To 7seg PCB CN8A 1
JS1125-10 10pin To 7seg PCB CN8A 0
B10B-PH-K-S 10pin To 7seg PCB CN8A 0
88 Connector PH-3A 3pin To VOL PCB/SW PCB CN2A CN7A 2
JS1125-3 3pin To VOL PCB/SW PCB CN2A CN7A 0
B3B-PH-K-S 3pin To VOL PCB/SW PCB CN2A CN7A 0
89 Connector PH-2A 2pin To Battery case CN1 1
JS1125-2 2pin To Battery case CN1 0
B2B-PH-K-S 2pin To Battery case CN1 0
90 Harness PH-2P 1007#24/L=200MM ZH-0064: to Battery case 2Pin AWG 24 200mm CN1-Battery 1
PH2P L=200mm ZH-0064: to Battery case 2Pin AWG 24 200mm CN1-Battery 0
91 Connector PH-2A 2pin to USB PCB CN6A 1
JS1125-2 2pin to USB PCB CN6A 0
B2B-PH-K-S 2pin to USB PCB CN6A 0
92 Connector PH-5A 5pin to USB PCB CN3A 1
JS1125-5 5pin to USB PCB CN3A 0
B5B-PH-K-S 5pin to USB PCB CN3A 0
93 Connector PH-7A 7pin to USB PCB / LED PCB CN4A CN5A 2
JS1125-7 7pin to USB PCB / LED PCB CN4A CN5A 0
B7B-PH-K-S 7pin to USB PCB / LED PCB CN4A CN5A 0
94 PCB PCB-5155A 4 LAYER FR-4 113X95mm 1
- 38 -
7seg PCB PCB-5157
No. NAME SPECIFICATIONS DESCRIPTION REFERENCE No. Q'ty
1 7SEGMENT LED E20561-GFOR DIP-18pin SEG1 1
TOD-5261BH-D-K DIP-18pin SEG1 0
R200 R201 R202 R203 R204
2 Resistor 1K-J 1/8W Pitch=7.5mm 8
R205 R206 R207
3 Harness PH-10Y 2651#26/L=80MM ZH-0062: to Main PCB 10Pin 2mmPitch 80mm CN8B-CN8A 1
PH10P L=80mm ZH-0062: to Main PCB 10Pin 2mmPitch 80mm CN8B-CN8A 0
4 Wire Jumper Φ0.5 Pitch 7.5mm JP202 1
5 PCB PCB-5157 FR-1 A part of Panel PCB 1
VR PCB PCB-5159
No. NAME SPECIFICATIONS DESCRIPTION REFERENCE No. Q'ty
1 Potentiometer RK0971110S0NB 10K-B 11detent with Nut(11mm) VR1 1
F-09115N-11CB10K-Y0L15FCx7(D) 10K-B 11detent with Nut Nut(11mm) VR1 0
2 Harness PH-3Y 2651#26/L=120MM ZH-0060: to Main PCB3Pin 2mmPitch 120mm CN2B-CN2A 1
PH3P L=120mm ZH-0060: to Main PCB3Pin 2mmPitch 120mm CN2B-CN2A 0
3 PCB PCB-5159 FR-1 A part of Panel PCB 1
- 39 -
MECHANICAL PARTS LIST
No. PART NAME SPECIFICATIONS DESCRIPTION REFERENCE No. Q'ty
1 G2.1u TOP COVER Z2B-0170 ADC12, Painted : black, silk 1 color : white (1) 1
2 G2.1u BOTTOM COVER Z2B-0171 ADC12, Painted : black (2) 1
3 G2 SWITCH BUTTON Z2B-0158 ABS(CLEAR) (3) Same as G2 1
4 G2.1u SW BUTTON R Z2B-0172 ABS(CLEAR) (4) 1
5 EX PEDAL SW BUTTON Z2B-0173 ABS(BLACK) (5) 1
6 VR KNOB 1 Z2B-0160 ABS, Chromium coatings (6) Same as G2 3
7 VR KNOB 2 Z2B-0161 ABS, Chromium coatings with indicator (color : black) (7) Same as G2 1
8 G2 SIDE COVER L Z2B-0162 ABS+TPE, CASE LEFT SIDE (8) Same as G2 1
9 G2.1u SIDE COVER R Z2B-0174 ABS+TPE, CASE RIGHT SIDE (9) 1
10 G2 DISPLAY COVER Z2B-0164 ABS, Chromium coatings (10) Same as G2 1
PCV / with adhesive tape, φ40mm t=1.0mm,
11 G2 DISPLAY SHEET Z2E-0188 (11) Same as G2 1
with silk print : 3 colors
PCV / with adhesive tape, 110X15,
12 G2.1u REAR SHEET Z2E-0195 (12) 1
with silk print : 2 colors
13 FOOT SW UNIT Z2A-0089 (13) Same as G2 2
14 FOOT SW DLESS PLATE Z2B-0165 ABS, Chromium coatings (14) Same as G2 2
15 EX PEDAL BASE Z2B-0175 ADC12, Paint (15) 1
16 EX PEDAL RUBBER Z2D-0048 TPE (16) 1
17 EX PEDAL SHAFT GUIDE Z2B-0176 POM (17) 2
HEXAGON SOCKET HEAD,
18 CAP SCREW (18) 1
M6x65, BLACK CHROMATE
19 HEXAGON U NUT M6, BLACK CHROMATE (19) Same as GFX-3 1
20 BKT PWB_PHOT Z2B-0178 ABS(BLACK) (20) 1
21 BATTERY CASE Z2B-0166 ABS(BLACK) (21) Same as G2 1
22 BATTERY CASE COVER Z2B-0167 ABS(BLACK) (22) Same as G2 1
23 BATTERY SPRING (+) Z2A-0082 SWIC-F d=0.7mm (23) Same as G2 1
24 BATTERY SPRING (-) Z2A-0083 SWIC-F d=0.7mm (24) Same as G2 1
25 BATTERY SPRING (+/-) Z2A-0084 SWIC-F d=0.7mm (25) Same as G2 1
26 G2.1u LED LENS A Z2B-0179 ABS(CLEAR) (26) 6
27 G2.1u LED LENS HOLDER Z2B-0180 ABS(BLACK) (27) 1
28 BATTERY CUSHION Z2E-0190 sponge 73.4x10.2 T=7, with adhesive tape (28) Same as G2 2
Sponge rubber (BLACK) , Hardness=40
80X10X3, 2 pieces for BOTTOM COVER,
29 CUSHION_UNDER_R Z2D-0052 1piece for PCB spacer (29) 3
30 EX PEDAL RUBBER 1 Z2D-0042-A4 KH-3 65(BLACK) (30) Same as GFX-3 1
31 EX PEDAL RUBBER 2 Z2D-0054 Sponge rubber (BLACK), Hardness=60 7X5t (31) 1
32 EX PEDAL RUBBER 3 Z2D-0055 CR60, 30X15X3t (32) 1
33 CUSHION UNDER EX Z2D-0056 CR60, 80X20X2t (33) 4
34 REFLECT SEAL Z2E-5032-A4 10x10x0.05mm , for PHOTO REFLECTOR (34) Same as GFX-3 1
SWCH(Fe), Black Chromate S Tight,
Cross Binding Head, M3X6L, PCB X2,
35 TAPPING SCREWS M3×6L S-TIGHT (35) 15
BOTTOM PLATE X5, FOOT_PCB X3,
USB_PCB X2, PH PCB X1, LED PCB X2
SWCH(Fe), Black Chromate P Tight,
36 TAPPING SCREWS M3x8L P-TIGHT (36) 3
BATT CASE X2, PH PCB X1
37 FILAMENT TAPE for ZH-0064 tape 3M 8915 Scotch 8915 Filament Tape, 12mm width, L=50mm Same as GFX-3 1
38 CAP Z2B-0183 ABS(BLACK) (37) 1
39 EX PEDAL SPACER Z2E-0203 PVC φ6.5mm t=0.5mm (38) 1
40 EX PEDAL SHAFT GUIDE-B Z2B-0185 POM (39) 2
41 G2.1u PHOTO SPACER Z2E-0204 PVC 10X10X0.5 (40) 1
42 FILAMENT TAPE for ZH-0068 tape 3M 8915 Scotch 8915 Filament Tape, 12mm width, L=25mm Same as GFX-3 1
43 TAPPING SCREWS M3x10L P-TIGHT SWCH(Fe), Chromate P Tight, 7SEG PCB X2 (41) 2
44 DOUBLE FACE (Tape) Z2E-0191 adhesive tape, for FOOT SW DRESS PLATE (42) 2
Molycote E Paste (White),
45 Lubricant For EX PEDAL SHAFT GUIDE 1
Specific gravity : 1.16g per cubic cm
46 Glue For EX PEDAL RUBBER SL518 1
- 40 -
Spare Parts Order List
ELECTRONIC PARTS The parts with ''*'' are available from G2.1u.
Main PCB : PCB-5155A (PCB-5155)
CODE No. NAME SPECIFICATIONS Q'ty PRICE(Japanese yen )
MICRO PROCESSOR
SP02032 MPU uPD703015BGC-A29-8EU(D163-0003) 1
SIGNAL PROCESSOR
SP02033 DSP ZFX-3 1
MEMORY
SP02034 SDRAM IS42S16100C1-7TL 1
SP02035 EEPROM IS93C86A-3GRLI 1
DIGITAL IC
SP02036 Logic IC SN74HCU04ANS 1
SP02037 Reset IC R3112Q291A-TR 1
A/D,D/A CONVERTER
SP00878 AD/DA Converter AK4552VT-E2 1 510
ANALOG
SP00071 OPAMP NJM2100M-TE1 1 50
SP00070 OPAMP NJM4558M-TE1 (Same as BA4558F) 1 40
SP00078 OPAMP NJM4556M-TE1 1 50
POWER SUPPLY
SP01945 Voltage Regulator uPC29M33AT-E1 1 90
SP02038 DC/DC Converter XC9502B093AR 1
TRANSISTOR
SP00628 Digital Transistor MUN5135DW1T1 (Same as UMB10N) 5
SP00110 Digital Transistor DTC-124EKA 5 100
SP02039 Transistor BC807-40 5
SP02040 Transistor BC817-40 5
SP02081 Transistor 2SB1706 5
DIODE
SP00123 Diode 1N4003 5 100
SP00352 Diode 1SS133T-77 5 100
SP00704 Chip Shottky Diode RB160L-40TE25 5 150
OSCILLATOR
SP02041 Ceramic Oscillator EFOMC2005T4 1
SP02042 Crystal Oscillator HC49U/S 24.576MHz 1
INDUCTOR
SP02043 Chip Inductor LQH43CN220K03 1
SP01762 Chip Inductor BLM18AG102SN1 10 200
RESISTOR
SP00582 Resistor 3.3-J 2W MOF 1 200
SP00740 Resistor Network 47k*4-J 10 200
JACK, SOKET
SP00590 Stereo Phone Jack SJ6336 (Same as HTJ-064-12D) 1 100
SP00589 Phone Jack SJ6335 (Same as HTJ-064-12I) 1 100
SP01500 DC Jack DC-05G Φ2.0 1 60
OTHER PARTS
SP00910 Slide SW SK22H09-G9 (Same as HSW2022-010020) 1 30
SP00931 FPC Connector 11311120-13420000 (Same as 20FMZ-ST) 1 90
SP02044 Connector PH10A 1
SP02006 Connector PH-3A (Same as JS-1125-3) 1 30
SP01951 Connector PH-2A (Same as JS-1125-2) 1 30
SP02045 Harness PH-2P 1007#24/L=200MM 1
- 41 -
7seg PCB : PCB-5157
CODE No. NAME SPECIFICATIONS Q'ty PRICE(Japanese yen)
DISPLAY DEVICE
SP02046 7segment LED E20561-GFOR 1
OTHER PARTS
SP02047 Harness PH-10Y 2651#26/L=80MM 1
VR PCB : PCB-5159
CODE No. NAME SPECIFICATIONS Q'ty PRICE(Japanese yen)
POTENTIOMETER
SP00149 potentiometer RK0971110S0NB (Same as SP02029 RK0971110S0P) 1 110
OTHER PARTS
SP02048 Harness PH-3Y 2651#26/L=120MM 1
PCB
CODE No. NAME SPECIFICATIONS Q'ty PRICE(Japanese yen)
PCB ASSEMBLY
FR-4 Double side pattern
* G2.1u MAIN PCB Assy 1
(PCB-5155Awith Harness)
FR-1 One side pattern
* G2.1u PANEL PCB Assy 1
(PCB-5156, PCB-5157, PCB-5158, PCB-5159 with Harness)
FR-4 Double side pattern
* G2.1u USB PCB Assy 1
( PCB-5160, PCB-5161, PCB-5162 with Harness)
- 42 -
Mechanical Parts
CODE No. NAME SPECIFICATIONS Q'ty PRICE(Japanese yen)
TOP COVER
* G2.1u TOP COVER Z2B-0170 1
LOWER PANEL
* G2.1u BOTTOM COVER Z2B-0171 1
SIDE COVER
SP02057 G2 SIDE COVER L Z2B-0162 1
* G2.1u SIDE COVER R Z2B-0174 1
FOOT PEDAL
* EX PEDAL BASE Z2B-0175 1
* EX PEDAL SHAFT GUIDE Z2B-0176 1
* BKT PWB_PHOT Z2B-0178 1
* EX PEDAL SPACER Z2E-0203 1
* EX PEDAL SHAFT GUIDE-BZ2B-0185 1
BUTTON, KNOB
SP02059 G2 SWITCH BUTTON Z2B-0158 1
SP02060 VR KNOB 1 Z2B-0160 1
SP02061 VR KNOB 2 Z2B-0161 1
* G2.1u SW BUTTON R Z2B-0172 1
* EX PEDAL SW BUTTON Z2B-0173 1
OTHER MOULDING PARTS
SP02062 G2 DISPLAY COVER Z2B-0164 1
SP02063 FOOT SW UNIT Z2A-0089 1
SP02064 FOOT SW DRESS PLATE Z2B-0165 1
SP02065 DOUBLE FACE (Tape) Z2E-0191 1
SP02066 BATTERY CASE Z2B-0166 1
SP02067 BATTERY CASE COVER Z2B-0167 1
SP02068 BATTERY CUSHION Z2E-0190 1
* D164 LED LENS A Z2B-0179 1
* D164 LED LENS HOLDER Z2B-0180 1
* D164 PHOTO SPACER Z2E-0204 1
* CAP Z2B-0183 1
RUBBER, SPRING
SP02069 FOOT RUBBER (REAR) Z2D-0045 1
SP02072 BATTERY SPRING (+) Z2A-0082 1
SP02073 BATTERY SPRING (-) Z2A-0083 1
SP02074 BATTERY SPRING (+/-) Z2A-0084 1
* EX PEDAL RUBBER Z2D-0048 1
* CUSHION_UNDER_R Z2D-0052 1
SP02025 EX PEDAL RUBBER 1 Z2D-0042 1
* EX PEDAL RUBBER 2 Z2D-0054 1
* EX PEDAL RUBBER 3 Z2D-0055 1
* CUSHION UNDER EX Z2D-0056 1
SCREW, WASHER, NUT
SP00621 TAPPING SCREWS M3×6L, S Tight, Black Chromate, SWCH(Fe) 10 20
SP01185 TAPPING SCREWS M3×8L, P Tight, Black Chromate, SWCH(Fe) 10 20
SP02075 TAPPING SCREWS M3×10L, P Tight, Chromate ,SWCH(Fe) 10 20
* CAP SCREW M6x65 1
SP01548 HEXAGON U NUT M6 1
SHEET, COLOR FILTER
SP02076 G2 DISPLAY SHEET Z2E-0188 1
* G2.1u REAR SHEET Z2E-0195 1
SP01535 REFLECT SEAL Z2E-5032 1
- 43 -
To: ZOOM Corp. Overseas Sales Group
Memo:
Company:
Signature:
Name:
ZOOM CORPORATION
2F, ITOHPIA IWAMOTO-CHO 2-CHOME BLDG.
2-11-2, Iwamoto-cho, Chiyoda-Ku, Tokyo
101-0032,Ja pan
PHONE: +81-3-5835-2200(MAIN)
FAX: +81-3-5835-2201
Web Site: http://www.zoom.co.jp
-44-
Supplement: Identification of main
PCB
Main PCB is common use for other production. Therefore, this main
PCB has check box to identify which production will be used for.
See below figure, it shows check box location on the main PCB (As of
September, 2005).
- 45 -