Sandvik 12WET 25-04-2012.pps
Sandvik 12WET 25-04-2012.pps
Wet Clutch
HPTO12 Wet Component
HPTO12TF-THTHZAZA-3
Filter Assembly
CHYFA-001-D
Torsional Coupling
Hydraulic
Clutch
Clutch Manifold
12Wet
UnitFX
Controller
SandvikFCACT5-F5B-A113
HF9917
Display
Speed Pickup
CHYMA-24V-004
CMCMU-008-12W
CMCDU-008
CECSP-003-D
Sandvik BT10028
Sandvik HV8629
HPTO12TF3-THTHZAZA-3
Sandvik EL9776
Filter Sandvik
ElementEL10051
Not Used By Sandvik
CHYFE-003Sandvik BT10027
Cooler HydraulicSandvik
Pump HF9920 Oil Reservoir
Output Shaft
Pump Drive Gear
Output Speed
Pick-up adjust to Breather
¾ turn out Input Speed Pick-
up adjust to 2 ½
turn out
Idler Gear
End Seal
Bell Housing Clutch Body (Cup)
Taper Bearing
End Stock
Hydraulic Manifold
4.5200⁰F
GPM
260Psi (18(17L/M)
400Psi Pressure
(93⁰C)
Bar)
(27.6 Priority
Transducer
Priority FlowValve
Temperature
Bar)
On/Off
PWM Control
Relieving
Relief
Coil
Coil Switch
Valve
CHYFV-005
CHYPT-003-D
CHYRV-260-002
CHYTS-200-001-D
CHYRV-400-001
CHYPV-003
CHYSV-004
Sandvik
Sandvik
Sandvik
Sandvik HV8634
EL10038EL10037
HV8630
HV8631
SandvikHV8633
Sandvik HV8632
GP1 = 0 Psi GP2 = 0 Psi
24 Volts + 12 Volts
24 Volts + 12 Volts
260PSI
≥ 4.5 volts
GP1 = 260 Psi GP2 = 0-225 Psi
Engaging 5 AMP
24 Volts + 12 Volts
ON/OFF Valve
PWM Valve
4 volts
Pro-Link Start Up
GP1 = 260 Psi GP2 = 225 Psi
Engaged 5 AMP
24 Volts + 12 Volts
ON/OFF Valve
PWM Valve
4 volts
GP1 = 260 Psi GP2 = 0-260 Psi
Disengaged 5 AMP
24 Volts + 12 Volts
ON/OFF Valve
PWM Valve
12 Wet Disengaging Holding Brake
Oil Travel
Filter
Pressure sensor
Filter Head
Filter Fault
– The Clutch Controller (Master Unit)
will ignore the filter switch for the
first 30 minutes once the engine has
been started. This is to allow for cold
start up when the filter will be in by-
pass
– Once this 30 minutes has elapsed and
there is a filter fault while operational
the Clutch Controller will start a 15
minute count down. It will also flash a
beacon(if fitted) and flash the “Filter
Clogged” LED.
– If after this time the clutch has not Element
been stopped then the Clutch
Controller will disengage the clutch
Clutch Controller (CMCMU-008-12W) ADV4
During engagement
– If the battery voltage to the clutch controller drops below 20Volts
– Too great a difference between the input and output speed (if you attempt an engagement and the mass is still
spinning)
– Engine speed dropped to zero or lost during engagement.
While engaged
– Clutch oil pressure 10% below 225Psi for a set period continually
– Temperature fault after being present for 15minutes.
– Filter clogged after 15 minutes of being engaged.
– Engine speed dropped below 500 rpm.
– Too great a difference between the input and output speed
Lockout
– In a lock out situation you will need to run the engine for 5 minutes continuously to clear the lock out fault.
Pro Link 2.1.1
Daily
– Check the oil level
– Check breather for clogs or obstructions
– Check ventilation holes in bell housing for clogs and obstructions
5000 hours
– Internal inspection and service
• Contact a PT Tech representative
What Oils
Temperature Range
Below -4⁰F (-20⁰C) -4⁰F to 32⁰F (-20⁰C to 0⁰C) Above 32⁰F (0⁰C)
Caterpillar Arctic (Cold
Mobilfluid LT Mobilfluid 424
weather TDTO)
Shell Spirax S3 TLV Caterpillar TDTO (10W only)
es
Typ ESSO Hydraul50 Shell Spirax S4 TXM
l
Oi
ESSO Hydraul 56