HD IR Waterproof Fixed Network Camera User’s Manual

Version 1.0.0
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

i
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1. This series product supports PoE too. Please note:
Do not connect these two power supplying sources to the device at the same time; it may result
in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.

6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

ii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

Network Camera Unit 1

Quick Start Guide 1

Installation Accessories Bag 1

CD 1

iii
 Table of Contents
1 General Introduction ..................................................................................................................1

1.1 Overview ........................................................................................................................1

1.2 Features.........................................................................................................................1

1.3 Specifications ................................................................................................................2

1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup ...........................................................................................3
2 Structure ......................................................................................................................................9

2.1 Multiple-function Combination Cable ........................................................................9

2.2 Framework and Dimension.........................................................................................9

3 Device Installation ....................................................................................................................11

4 Quick Configuration Tool.........................................................................................................13

4.1 Overview ......................................................................................................................13

4.2 Operation .....................................................................................................................13

5 Web Operation..........................................................................................................................16

5.1 Network Connection...................................................................................................16

5.2 Login and Logout........................................................................................................16

6 FAQ ............................................................................................................................................19

Appendix Toxic or Hazardous Materials or Elements ...............................................................20

iv
1 General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.

This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for
use in the outdoor environments.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.

1.2 Features
z Different user rights for each group, one user belongs to one group.
User
z The user right shall not exceed the group right.
Management
z Support central server backup function in accordance with your configuration
and setup in alarm or schedule setting
Storage
z Support record via Web and the recorded file are storage in the client-end
Function
PC.
z Support network storage function such as FTP.
z It supports one-channel video data transmit to network terminal and then
decode. Delaying time is within 270ms (network bandwidth support needed)
z Max supports 20 connections and output bandwidth is 32Mbps. System
Network
refuses new connection request once it exceeds the bandwidth threshold.
Monitor
z Adopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
z Support web access.
Network z Realize network camera configuration and management via Ethernet.
Management z Support device management via web or client-end.
z External power adapter DC 12V.
z Support PoE.
Power Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
z Log function
z Support system resource information and running status real-time display.
z Day/Night mode auto switch.
z Support picture parameter setup such as electronic shutter and gain setup.
Assistant z Support motion detect.
Function z Backlight compensation: screen auto split to realize backlight compensation
to adjust the bright.
z Support video watermark function to avoid vicious video modification.
z Built-in IR light. Support IR night vision.
z The enclosure conforms to the IP 66 protection. Has the waterproof function.

1
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model Parameter

Main Processor TI Davinci high performance DSP

System

OS Embedded LINUX
System Support real-time network, local record, and remote operation at the
Resources same time.
User Interface Remote operation interface such as WEB, DSS, PSS
System Status Bit stream statistics, log, and software version.
Image Sensor 1/3-inch CMOS
Video Parameter

Pixel 1920(H)*1080(V)
Gain Control Fixed/Auto
White Balance Manual/Auto
Manual/Auto
Exposure Mode PAL: It ranges from 1/4 to 1/10000
NTSC: It ranges from 1/3 to 1/10000
Video
Compression H264/ H.264B/MJPEG
Standard
PAL:
Main stream(1920*1080@25fps)，
Video Frame extra stream(352*288@25fps)
Rate NTSC:
Main stream(1920*1080@30fps)，
extra stream(352*240@30fps)
H.264: 56Kbps-8192Kbps.
Video Bit Rate MJPEG is adjustable and bit rate is adjustable.
Support customized setup.
Support mirror.
Video Flip
Support flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Channel title, time title, motion detect, camera masking.
Information
Lens 3.6mm, 6mm, 8mm. Fixed focus.
Lens Interface M12. Lens is the default accessories
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The
Video

6th level has the highest sensitivity)

Motion Detect
Activation event: video storage, image snapshot, log, email function
and etc.
Backup
and
Record

Storage Support display local storage status

Management

Wire Network 1- channel wire Ethernet port, 10/100 Base-T Ethernet

ork
Netw

Network Protocol Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,

2
 SNMP.
Remote Monitor, system setup, file download, log information, maintenance ,
Operation upgrade and etc
Restore Default
Reset button
Setup
IR light IR light 20-30M.
Power DC12V power and PoE.
General Parameter

Power 6W MAX
Consumption
Working
-10℃~+60℃
Temperature
Working
10%~90%
Humidify
Dimensions(mm) 70*66*160
Weight 0.5Kg（Excluding box）
Installation Bracket installation

1.3.2 Factory Default Setup

Please refer to the following sheet for factory default setup information.
Default Setup
Setup Item

Brightness 50
Camera

Conditions

Contrast 50
Saturation 50
Sharpness 50
Anti-flicker Outdoor
Exposure Mode Auto
Gain Adjust 0-50
Scene Mode Auto
Day/night Mode Auto
BLC Off
Mirror Off
Flip Off
Main Bit stream
Video

Video bit stream

General
Stream type
Encode
H.264
mode
Resolution 1080P（1920*1080）
Frame Rate PAL:25
（FPS） NTSC:30
Bit Rate
CBR
Type
Recommen
3584-8192 Kb/S
ded Bit

Bit Rate 8192

Watermark Enable

3
 Default Setup
Setup Item

Watermark
DigitalCCTV
character
Enable Enable
Bit stream
General
type
Encode
H.264
mode
PAL:CIF(352*288)
Resolution
NTSC:CIF(352*240)
Sub
Frame Rate PAL:25
Stream
（FPS） NTSC:30
Bit Rate
CBR
Type
Recommen
192-1024Kb/S
ded Bit

Bit Rate 1024

Snapshot
General
Type
Snapshot Image Size 1080P（1920*1080）
Quality 5
Interval 1s
Privacy
Disable
Mask
Video Overlay Channel
Enable
Title
Time Title Enable
Snapshot
C:\PictureDownload
Path Path
Record Path C:\RecordDownload
TCP/IP Host Name IPC
Network

Ethernet
Wire
Card
Mode Static
Mac
Device MAC address when it is shipped out of the factory
Address
IP Version IPV4
IP Address 192.168.1.108
Subnet
255.255.255.0
Mask
Default
192.168.1.1
Gateway
Preferred
8.8.8.8
DNS
Alternate
8.8.8.8

4
 Default Setup
Setup Item

DNS
Enable
ARP/Ping
set device Enable
IP address
service
Max
10
Connection
TCP Port 37777
UDP Port 37778

Connection HTTP Port 80

RTSP Port 554

HTTPs
Disable
enable
HTTPs Port 443
Enable Disable
PPPoE Username none
Password N/A
Server Type Disable，CN99 DDNS
Server IP none
Server Port 80
Domain
DDNS none
Name
User none
Password ****

Update
10 minutes
Period
Trusted
IP Filter Disable
sites
SMTP
SMTP(Email) none
Server
Port 25
Anonymity Disable
User Name anonymity
Password ****

Sender none
Authenticati
on
N/A
(Encryption
mode)

5
 Default Setup
Setup Item

Title
IPC Message
(Subject)
Attachment N/A
Mail
0 seconds
Receiver
Email Test Disable，interval=60 seconds
Enable
UPnP Disable
UPnP

SNMP Port 161

Read
public
Community

SNMP Write
private
Community
Trap
N/A
Address
Trap Port 162
Enable Enable
Bonjour Server
SN. It depends on the actual device.
Name
Multicast
239.255.42.42
Multicast Address
Port 36666
Real-time
0
QoS Monitor
Command 0
Enable Disable
Event

Video detect

Anti-dither 5 seconds
Sensitivity 3
Record
Enable
Motion Detect Channel
Record
10 seconds
Delay
Send Email Disable
Snapshot Disable
Enable Disable
Record
Enable
Channel
Video
Record
Masking 10 seconds
Delay
Send Email Disable
Snapshot Disable
Disconnectio Enable Disable

6
 Default Setup
Setup Item

n Record Enable
Record
10 seconds
Delay
Enable Disable
Record Enable
IP Conflict
Relay out
10 seconds
Delay
Enable FTP Disable
Storage

Storage

Server IP N/A
Port 21
FTP Username anonymity
Password N/A
Remote
share
path
Pack
8 minutes
Duration
Pre-record 5 seconds
Disk Full Overwrite
Record Control
Record Auto
Mode
Record
Main stream
Stream
Device No Device manufacture SN
System

General

Language English
Local Host
Video
PAL
Standard
Date Format Y-M-D
Time
24H
Format
Time Zone GMT+08:00
System
Sync
Time
DST Disable
Date and
time DST Type Week
Start Time 00:00:00 of the first Sunday of the month
End Time 00:00:00 of the second Monday of the month
NTP Disable
NTP Server clock.isc.org
Port 37
Update
10 minutes
Period
Auto Maintenance Auto Reboot Enable Each 02:00 Tuesday

7
 Default Setup
Setup Item

Auto Delete
Disable
Old Files

8
 2 Structure
2.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function combination cable information. See Figure
2-1.

Figure 2-1
Please refer to the following sheet for detailed information.
SN Port Name Function Connection Note
Ethernet
1. LAN Network port Connect to standard Ethernet cable.
port
Power input
2 DC12V / Power input port. Input DC 12V.
port

2.2 Framework and Dimension

Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.

9
Figure 2-2

Figure 2-3

10
3 Device Installation
Important
The installation wall shall min sustain 3X weight of the bracket and camera.
Please follow the steps listed below to install the device. Please refer to Figure 3-1 and Figure 3-2 for
reference.
Step 1
Paste the installation map on the surface of the wall or the ceiling.
Step 2
Dig the installation holes according to the installation map.

Figure 3-1
Step 3
Open the accessories bag and then take the expansion bolt out. Insert the expansion bolt into the
installation holes.
Step 4
Take the screws from the accessories bag and then use them to secure the device on the installation
surface of the wall or the ceiling. The sun shield of the device can move forward or backward. Please
secure the set screw of the sun shield after you fixed the device.
Step 5
Connect the corresponding cables.
Step 6
Use the cross-head screwdriver to loosen the adjust screw.
Step 7
Turn the device in different directions to make it suitable for the monitor position.
Step 8
Use the cross-head screwdriver to fix the adjust screw firmly.

11
Figure 3-2

12
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation
Double click the “ConfigTools.exe” icon; you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.

Figure 4-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Note:
You can set the IP address, subnet mask and gateway for the network camera and PC. Please note
network camera IP address and PC IP address shall be in the same network segment if there is no
router. Network camera default IP address is 192.168.1.108. If there is a router, please set the
corresponding gateway and subnet mask.
The factory default user name is admin and password is admin. For security reasons, please modify
your password after you first login.
For detailed WEB operation, please refer to the network camera Web Operation Manual in the
resource CD.

13
 Figure 4-2
Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure
4-3.

Figure 4-3
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you can not login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

14
 Figure 4-4
After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.

Figure 4-5
For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

15
5 Web Operation
This series network camera product supports the Web access and management via PC.
Web includes several modules: monitor channel preview, system configuration, alarm and etc.

5.1 Network Connection

Please follow the steps listed below for network connection.
z Make sure the network camera has connected to the network properly.
z Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1
z Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

5.2 Login and Logout

Open IE and input network camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 5-1.

Input your IP
address here

Figure 5-1
The login interface is shown as below. See Figure 5-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.

16
 Figure 5-2
If it is your first time to login, system pops up warning information to ask you whether install control
webrec.cab or not after you logged in for one minute. Please click OK button, system can
automatically install the control. When system is upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable
the control download. Or you can lower the IE security level. See Figure 5-3.

Figure 5-3
After you logged in, you can see the main window. See Figure 5-4.

17
 Figure 5-4
Please refer to the Web Operation Manual included in the resource CD for detailed operation
instruction.

18
6 FAQ
Bug
I can not boot up Please click RESET button for at least five seconds to restore
the device or factory default setup.
operate properly.
The water leakage The unauthorized front or rear cap remove many result in water
occurred. leakage.
The glass front cap has sustained heavy push or strike.
The waterproof plug of the rear cap becomes loosen.
IR video is poor. Do not use the proper supplying power. The IR light can not turn on
completely.
The object is out of the IR distance range of current device.
IR-CUT does not turn to the night mode. The photosensitive chip of
the front-end can not sense the IR light.
I can not upgrade
When network upgrade operation failed, you can use port 3800 to
the device via
continue upgrade.
network.
I can not login the z For Windows OS 98 or Windows ME user, if you can not install
client-end or the the client-end or can not view after the installation. We
WEB. recommend the win2000sp4 OS or install the client-end of the
low version.
z The Active X control is blocked.
z The display card version shall be dx8.1 or higher.
z Network connection error occurred.
z Invalid network setup.
z Invalid user name or password.
I can not play the z There is no player.
download file. z There is no DX8.1 or higher.
z For the MEDIA PLAYER, there shall be Div X503Bundle.exe
plugin if you play the .AVI file.
z For Windows XP user, you need to install the plugin
DivX503Bundle.exe and ffdsho-2004 1012.exe.
To guarantee After you modified the important setup, please reboot the device via
setup update the software to make sure the setup has been updated to the
storage medium.
Power adapter z The general power adapter can work ranging from 0℃ to 40 ℃.
The device may result in unstable power supply when the
temperature exceeds the working temperature.
z Please replace an industry-level power adapter if you are using
in the harsh environments.

19
Appendix Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name
Pb Hg Cd Cr VI PBB PBDE

Circuit Board
○ ○ ○ ○ ○ ○
Component

Device Case ○ ○ ○ ○ ○ ○

Wire and Cable ○ ○ ○ ○ ○ ○

Packing
○ ○ ○ ○ ○ ○
Components
Accessories ○ ○ ○ ○ ○ ○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.

Note
z This user’s manual is for reference only. Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z All trademarks and registered trademarks mentioned are the properties of their respective
owners.
z If there is any uncertainty or controversy, please refer to the final explanation of us.
z Please visit our website for more information.

20