Professional Documents
Culture Documents
Ultra: DSE332 ATS Control Module
Ultra: DSE332 ATS Control Module
DSEULTRA
DSE332 ATS Control Module
Document Number 057-097
Author : Anthony Manton
DSE Model 332 ATS Control and Instrumentation System Operators Manual
E-mail: [email protected]
Website: www.deepseaplc.com
The DSE logo and the names DSEUltra, DSEControl, DSEPower, DSEExtra, DSEMarine and DSENet are UK registered
trademarks of Deep Sea Electronics PLC.
Any reference to trademarked product names used within this publication is owned by their respective companies.
Deep Sea Electronics Plc reserves the right to change the contents of this document without prior notice.
Indicates a procedure or practice, which, if not strictly observed, could result in damage or
CAUTION! destruction of equipment.
Indicates a procedure or practice, which could result in injury to personnel or loss of life if not
WARNING! followed correctly.
2 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
TABLE OF CONTENTS
1 BIBLIOGRAPHY ........................................................................... 6
2 INTRODUCTION........................................................................... 6
3 SPECIFICATIONS ........................................................................ 7
3.1 PART NUMBERING................................................................................ 7
3.1 POWER SUPPLY REQUIREMENTS ....................................................... 8
3.2 TERMINAL SPECIFICATION.................................................................. 8
3.3 MAINS VOLTAGE / FREQUENCY SENSING .......................................... 8
3.4 INPUTS .................................................................................................. 9
3.4.1 DIGITAL INPUTS .................................................................................................. 9
3.5 OUTPUTS ............................................................................................... 9
3.5.1 GENERATOR / MAINS LOADING OUTPUTS ........................................................ 9
3.5.2 CONFIGURABLE OUTPUTS................................................................................. 9
3.5.3 START/RUN OUTPUT .......................................................................................... 9
3.6 COMMUNICATION PORTS .................................................................... 9
3.7 DIMENSIONS AND MOUNTING ........................................................... 10
3.7.1 DIMENSIONS ..................................................................................................... 10
3.7.2 PANEL CUTOUT ................................................................................................ 10
3.7.3 WEIGHT ............................................................................................................ 10
3.7.4 FIXING CLIPS .................................................................................................... 10
3.7.5 OPTIONAL SILICON SEALING GASKET............................................................. 10
3.8 APPLICABLE STANDARDS ................................................................. 11
4 INSTALLATION .......................................................................... 12
4.1 TERMINAL DESCRIPTION ................................................................... 12
4.1.1 DC SUPPLY AND OUTPUTS .............................................................................. 12
4.1.2 DIGITAL INPUTS ................................................................................................ 13
4.1.3 LOAD SWITCHING AND GENERATOR SENSING ............................................... 13
4.1.4 MAINS SENSING ................................................................................................ 13
4.1.5 CURRENT TRANSFORMERS ............................................................................. 14
4.1.6 PC CONFIGURATION INTERFACE CONNECTOR............................................... 15
4.2 TYPICAL WIRING DIAGRAM ............................................................... 16
5 DESCRIPTION OF CONTROLS ................................................. 18
5.1 QUICKSTART GUIDE ........................................................................... 20
5.1.1 STANDBY OPERATION...................................................................................... 20
5.2 GRAPHICAL DISPLAY ......................................................................... 21
5.2.1 DISPLAY PAGES................................................................................................ 21
5.2.1.1 STATUS.................................................................................................................................21
5.2.1.2 INSTRUMENTATION ............................................................................................................21
5.2.1.3 ALARMS................................................................................................................................22
5.2.1.4 EVENT LOG ..........................................................................................................................22
5.2.1.5 LCD INDICATORS ................................................................................................................22
5.2.1.6 SCHEDULE ...........................................................................................................................22
5.2.1.7 ABOUT ..................................................................................................................................23
5.3 CONTROLS .......................................................................................... 24
5.3.1 MODE SELECTION ............................................................................................ 24
5.3.2 DISPLAY ............................................................................................................ 24
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 3
DSE Model 332 ATS Control and Instrumentation System Operators Manual
6 OPERATION ............................................................................... 25
6.1 AUTOMATIC MODE OF OPERATION .................................................. 25
6.1.1 WAITING IN AUTO MODE ..................................................................................25
6.1.2 STARTING SEQUENCE ......................................................................................25
6.1.3 GENERATOR ON LOAD .....................................................................................25
6.1.4 STOPPING SEQUENCE......................................................................................25
6.2 MANUAL OPERATION ......................................................................... 27
6.2.1 STARTING SEQUENCE ......................................................................................27
6.2.2 GENERATOR OFF LOAD ...................................................................................27
6.2.3 GENERATOR ON LOAD .....................................................................................27
6.2.4 TRANSFER BUTTONS OPERATION...................................................................27
6.2.5 STOPPING SEQUENCE......................................................................................27
6.3 TEST ON LOAD OPERATION .............................................................. 29
6.3.1 STARTING SEQUENCE ......................................................................................29
6.3.2 GENERATOR ON LOAD .....................................................................................29
6.3.3 STOPPING SEQUENCE......................................................................................29
6.4 LOAD SWITCHING CONTROL ............................................................. 30
6.4.1 BREAKER SCHEME A ........................................................................................30
6.4.1.1 CHECK SYNCHRONISING IS DISABLED .......................................................................... 30
6.4.1.1.1 MAINS / GENERATOR LOAD INHIBIT ...........................................................................................................30
6.4.1.1.2 LOAD SHEDDING ............................................................................................................................................30
6.4.1.1.3 TIMING DIAGRAM .............................................................................................................................................30
6.4.1.2 CHECK SYNCHRONISING IS ENABLED ........................................................................... 31
6.4.1.2.1 MAINS / GENERATOR LOAD INHIBIT ...........................................................................................................31
6.4.1.2.2 LOAD SHED INPUT..........................................................................................................................................31
6.4.1.2.3 LOAD TRANSFER............................................................................................................................................31
6.4.1.2.4 TIMING DIAGRAM .............................................................................................................................................31
6.4.2 BREAKER SCHEME B ........................................................................................32
6.4.2.1 CHECK SYNCHRONISING IS DISABLED .......................................................................... 32
6.4.2.1.1 TRANSFERRING TO GENERATOR...............................................................................................................32
6.4.2.1.2 TRANSFERRING TO MAINS ...........................................................................................................................32
6.4.2.1.3 LOAD SHED INPUT..........................................................................................................................................32
6.4.2.1.4 TIMING DIAGRAM .............................................................................................................................................32
6.4.2.2 CHECK SYNCHRONISING IS ENABLED ........................................................................... 33
6.4.2.2.1 TRANSFER TO GENERATOR........................................................................................................................33
6.4.2.2.2 TRANSFER TO MAINS ....................................................................................................................................33
6.4.2.2.3 LOAD SHED INPUT..........................................................................................................................................33
6.4.2.2.4 TIMING DIAGRAM .............................................................................................................................................33
4 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
11 DISPOSAL ............................................................................... 40
11.1 WEEE (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT) ..... 40
11.2 ROHS (RESTRICTION OF HAZARDOUS SUBSTANCES) ................. 40
12 APPENDIX ............................................................................... 41
12.1 COMMUNICATIONS OPTION CONNECTIONS .................................. 41
12.1.1 DESCRIPTION ................................................................................................... 41
12.1.2 PC TO CONTROLLER (DIRECT) CONNECTION................................................. 41
12.2 ENCLOSURE CLASSIFICATIONS ..................................................... 42
12.2.1 IP CLASSIFICATIONS......................................................................................... 42
12.2.2 NEMA CLASSIFICATIONS .................................................................................. 43
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 5
DSE Model 332 ATS Control and Instrumentation System Operators Manual
1 BIBLIOGRAPHY
This document refers to and is referred to by the following DSE publications which can be obtained from the DSE
website www.deepseaplc.com
2 INTRODUCTION
This document details the installation and operation requirements of the DSE332 Series modules, part of the
DSEUltra® range of products.
The manual forms part of the product and should be kept for the entire life of the product. If the product is passed or
supplied to another party, ensure that this document is passed to them for reference purposes.
This is not a controlled document. You will not be automatically informed of updates. Any future updates of this
document will be included on the DSE website at www.deepseaplc.com
The DSE 332 series module has been designed to allow the operator to control the transfer of the load from one
supply to another, typically the mains supply and a standby generator.
The user also has the facility to view the system operating parameters via the LCD display.
The DSE 332 module monitors the supplies, indicating the operational status and fault conditions, automatically
transferring the load to the backup supply in case of mains supply failure. The LCD display indicates the status.
The powerful microprocessor contained within the module allows for incorporation of a range of enhanced features:
Using a PC and the DSE Configuration Suite software allows alteration of selected operational sequences, timers
and alarm trips.
Additionally, the module’s integral fascia configuration editor allows adjustment of this information.
A robust plastic case designed for front panel mounting houses the module. Connections are via locking plug and
sockets.
6 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
3 SPECIFICATIONS
3.1 PART NUMBERING
0332 - 001 - 01
Variant
Product type
Hardware revision
Revision 1 001
At the time of this document production, there have been no revisions to the module hardware.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 7
DSE Model 332 ATS Control and Instrumentation System Operators Manual
8 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
3.4 INPUTS
Number 10
Arrangement Contact between input terminal and the module’s plant supply negative terminal
Low level threshold 3.2V minimum
High level threshold 8.1V maximum
Maximum input voltage +60V DC with respect to module’s plant supply negative terminal
Minimum input voltage -2V DC with respect to module’s plant supply negative terminal
Contact wetting current 7mA ±1mA
Open circuit voltage 12V ±1V
3.5 OUTPUTS
USB Port USB2.0 Device for connection to PC running DSE configuration suite only
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 9
DSE Model 332 ATS Control and Instrumentation System Operators Manual
3.7.1 DIMENSIONS
216mm x 158mm x 42mm
(8.5” x 6.2” x 1.6”)
3.7.3 WEIGHT
510g (0.51kg)
Fixing clip
NOTE:- In conditions of excessive vibration, mount the panel on suitable anti-vibration mountings.
Gasket fitted to
Sealing gasket module
10 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
BS 4884-1 This document conforms to BS4884-1 1992 Specification for presentation of essential
information.
BS 4884-2 This document conforms to BS4884-2 1993 Guide to content
BS 4884-3 This document conforms to BS4884-3 1993 Guide to presentation
BS EN 60068-2-1
-30°C (-22°F)
(Minimum temperature)
BS EN 60068-2-2
+70°C (158°F)
(Maximum temperature)
BS EN 60950 Safety of information technology equipment, including electrical business equipment
BS EN 61000-6-2 EMC Generic Immunity Standard (Industrial)
BS EN 61000-6-4 EMC Generic Emission Standard (Industrial)
BS EN 60529 IP65 (front of module when installed into the control panel with the optional sealing
(Degrees of protection gasket)
provided by enclosures) IP42 (front of module when installed into the control panel WITHOUT being sealed to
the panel)
UL508 12 (Front of module when installed into the control panel with the optional sealing
NEMA rating gasket).
(Approximate) 2 (Front of module when installed into the control panel WITHOUT being sealed to the
panel)
IEEE C37.2 Under the scope of IEEE 37.2, function numbers can also be used to represent
(Standard Electrical Power functions in microprocessor devices and software programs.
System Device Function The 3000 series controller is device number 11L-6000 (Multifunction device protecting
Numbers and Contact Line (generator) – 6000 series module).
Designations)
As the module is configurable by the generator OEM, the functions covered by the
module will vary. Under the module’s factory configuration, the device numbers
included within the module are :
In line with our policy of continual development, Deep Sea Electronics, reserve the right to change specification without notice.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 11
DSE Model 332 ATS Control and Instrumentation System Operators Manual
4 INSTALLATION
12 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
CABLE
PIN No DESCRIPTION NOTES
SIZE
Mains L1 (R) voltage 1.0mm² Connect to Mains L1 (R) output (AC)
27
monitoring AWG 18 (Recommend 2A fuse)
Mains L2 (S) voltage 1.0mm² Connect to Mains L2 (S) output (AC)
28
monitoring AWG 18 (Recommend 2A fuse)
Mains 31 (T) voltage 1.0mm² Connect to Mains L3 (T) output (AC)
29
monitoring AWG 18 (Recommend 2A fuse)
1.0mm²
30 Mains Neutral (N) input Connect to Mains Neutral terminal (AC)
AWG 18
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 13
DSE Model 332 ATS Control and Instrumentation System Operators Manual
Current transformers are fitted in the feed from the transfer switch to the load. They are used to give mains
instrumentation when the mains is on load, and generator instrumentation when the generator is on load.
WARNING!:- Do not disconnect this plug when the CTs are carrying current. Disconnection will open
circuit the secondary of the C.T.’s and dangerous voltages may then develop. Always ensure the CTs are
not carrying current and the CTs are short circuit connected before making or breaking connections to the
module.
NOTE:- The DSE332 series module has a burden of 0.5VA on the CT. Ensure the CT is rated for the
burden of the DSE332 series controller, the cable length being used and any other equipment sharing the
CT. If in doubt, consult your CT supplier.
NOTE:- Take care to ensure correct polarity of the CT primary as shown below. If in doubt, check with
the CT supplier.
CT labelled as To Load
p1, k or K
CT labelled as
p2, l or L
To Supply
14 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
NOTE:- The USB connection cable between the PC and the 6000 series module must not be extended
beyond 5m (5yds). For distances over 5m, it is possible to use a third party USB extender. Typically, they
extend USB up to 50m (yds). The supply and support of this type of equipment is outside the scope of
Deep Sea Electronics PLC.
CAUTION!: Care must be taken not to overload the PCs USB system by connecting more than the
recommended number of USB devices to the PC. For further information, consult your PC supplier.
CAUTION!: This socket must not be used for any other purpose.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 15
DSE Model 332 ATS Control and Instrumentation System Operators Manual
As every system has different requirements, these diagrams show only a TYPICAL system and do not intend to
show a complete system.
Genset manufacturers and panel builders may use these diagrams as a starting point, however you are referred to
the completed system diagram provided by your system manufacturer for complete wiring detail.
Further wiring suggestions are available in the following DSE publication, available at www.deepseaplc.com.
16 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 17
DSE Model 332 ATS Control and Instrumentation System Operators Manual
5 DESCRIPTION OF CONTROLS
The following section details the function and meaning of the various controls on the module.
Common Alarm
Indicator
Info button
Toggle generator
Toggle mains load switch
load switch Select Test on
Load mode
Select Manual
Select Auto Mode
mode
18 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
Mains Available
Generator Available
Generator On load
Mains On Load
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 19
DSE Model 332 ATS Control and Instrumentation System Operators Manual
NOTE:- For further details, see the section entitled ‘OPERATION’ elsewhere in this manual.
NOTE:- If module power is removed, it will ‘remember’ the last operating mode and return to that mode
next time power is applied.
20 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
It is possible to scroll to display the different pages of information by repeatedly operating the scroll button
Once selected the page will remain on the LCD display until the user selects a different page or after an extended
period of inactivity, the module will revert to the status display.
When scrolling manually, the display will automatically return to the Status page if no buttons are pressed for the
duration of the configurable LCD Page Timer.
If an alarm becomes active while viewing the status page, the display shows the Alarms page to draw the operator’s
attention to the alarm condition.
At power up, the display will show the software version, and then display the default display screen, which will
display Mains instrumentation.
5.2.1.1 STATUS
Example :
5.2.1.2 INSTRUMENTATION
Example::
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 21
DSE Model 332 ATS Control and Instrumentation System Operators Manual
5.2.1.3 ALARMS
Example
Example:
Example:
5.2.1.6 SCHEDULE
Example:
22 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
5.2.1.7 ABOUT
Example:
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 23
DSE Model 332 ATS Control and Instrumentation System Operators Manual
5.3 CONTROLS
This button places the module into its ‘Automatic’ mode. This mode allows the module to control the
function of the load switching completely automatically. The module will monitor the remote start input and
mains supply status and once a start request is made, the set will be placed on load.
Upon removal of the starting signal (or the mains supply returns), the module will automatically transfer
the load from the generator to the mains and remove the genset starting instruction.
For further details, please see the more detailed description of ‘Auto operation’ elsewhere in this
manual.
Operation is as AUTO MODE above but the load is not transferred back to the mains supply when it is
reinstated. This function is sometimes called “MANUAL RESTORE”
Once in Test on load mode the module will send a start request to the generator and place the set on
load. The set will remain on load when in this mode.
This mode allows manual control of the ATS functions. Once in Manual mode the module will send a start
request to the generator.
Breakers can be opened and close using the transfer buttons detailed below.
5.3.2 DISPLAY
This button changes between the various pages About, Status, Instrumentation, Alarms, Event Log, LCD
Indicators
This buttons scrolls through the items in the currently displayed page.
Two fascia mounted buttons are provided for load switching operation when in manual mode. These buttons are
enabled/disabled in the modules PC configuration Suite so refer to your configuration file to ensure the configuration
has enabled the buttons.
Pressing this button when the mains is on load will open the mains load switch.
Pressing this button when the generator is on load and the mains is healhty, will open the generator load
switch, wait for the duration of the transfer delay, then close the mains load switch.
Pressing this button when the generator is on load will open the generator load switch.
Pressing this button when the mains is on load and the generator is available, will open the mains load
switch, wait for the duration of the transfer delay, then close the generator load switch.
24 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
6 OPERATION
6.1 AUTOMATIC MODE OF OPERATION
NOTE:- If a digital input configured to panel lock is active, changing module modes will not be
possible. Viewing the instruments and event logs is NOT affected by panel lock.
If a starting request is made and there is no input present for Auto Start Inhibit, the starting sequence will begin.
Starting requests can be from the following sources :
• Mains failure
• Activation of an auxiliary input that has been configured to remote start
• Activation of the inbuilt exercise scheduler.
To allow for ‘false’ start requests, the start delay timer begins.
Should all start requests be removed during the start delay timer, the unit will return to a stand-by state.
If a start request is still present at the end of the start delay timer, start signal is given to the generator set by the
start/run output.
If the generator fails to become available before the generator failure timer expires. This is indicated on the LCD
display, but the starting signal remains active.
Once the generator is measured as being within limits (and the Auxiliary Generator Ready signal is received, the
mains is removed from the load, and after the transfer timer has expired, the generator is placed on load.
If all start requests are removed and there is no input present for Auto Restore Inhibit, the stopping sequence will
begin.
The return delay timer operates to ensure that the starting request has been permanently removed and isn’t just a
short term removal.
After the return delay timer, the generator load switch is opened, then after the transfer timers, the mains is placed
back on load.
Should another start request be made during the cooling down period, the generator will be placed on load.
The cooling timer allows the set to run off load and cool sufficiently before being stopped. This is particularly
important where turbo chargers are fitted to the engine.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 25
DSE Model 332 ATS Control and Instrumentation System Operators Manual
NOTE:- If module power is removed, it will ‘remember’ the operating mode and return to that mode next
time power is applied.
26 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
NOTE:- If a digital input configured to panel lock is active, changing module modes will not be
possible. Viewing the instruments and event logs is NOT affected by panel lock.
Manual mode allows the operator to start and stop the set manually, and if required change the state of the load
switching devices. Manual off load mode is active when the Manual button is pressed.
The start request is sent to the generator via the start/run relay output.
If the generator fails to become available before the generator failure timer expires. This is indicated on the LCD
display, but the starting signal remains active.
The generator will continue run OFF LOAD in this mode unless :
Two fascia mounted buttons are provided for load switching operation when in manual mode. These buttons are
enabled/disabled in the modules PC configuration Suite so refer to your configuration file to ensure the configuration
has enabled the buttons.
Pressing this button when the mains is on load will open the mains load switch.
Pressing this button when the generator is on load and the mains is healhty, will open the generator load
switch, wait for the duration of the transfer delay, then close the mains load switch.
Pressing this button when the generator is on load will open the generator load switch.
Pressing this button when the mains is on load and the generator is available, will open the mains load
switch, wait for the duration of the transfer delay, then close the generator load switch.
To begin the stopping sequence, the module should be placed in the AUTO or PROHIBIT RETURN mode.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 27
DSE Model 332 ATS Control and Instrumentation System Operators Manual
NOTE:- If module power is removed, it will ‘remember’ the operating mode and return to that mode next
time power is applied.
28 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
NOTE:- If a digital input configured to panel lock is active, changing module modes will not be
possible. Viewing the instruments and event logs is NOT affected by panel lock.
Manual mode allows the operator to start and stop the set manually, and if required change the state of the load
switching devices. Manual off load mode is active when the Test on Load button is pressed.
The start request is sent to the generator via the start/run relay output.
If the generator fails to become available before the generator failure timer expires. This is indicated on the LCD
display, but the starting signal remains active.
• The generator supply fails – The mains supply is placed back on load if available.
• An input is given for Transfer to Mains
To begin the stopping sequence, the module should be placed in the AUTO or PROHIBIT RETURN mode.
NOTE:- If module power is removed, it will ‘remember’ the operating mode and return to that mode next
time power is applied.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 29
DSE Model 332 ATS Control and Instrumentation System Operators Manual
The following timing diagrams detail the differences between the load switching control options.
NOTE : Generator Closed Auxiliary and Mains Closed Auxiliary inputs do not affect the operation of the
load switching in Breaker Scheme A
Activation of an input configured to mains load inhibit or generator load inhibit inputs cause the corresponding
breaker to be opened immediately. No other change in function will occur.
When the input is deactivated the breaker is closed again if appropriate.
If an input configured to Load Shed is activated, outputs set to Open Mains and Open Gen will energise, and inputs
configured to Close Mains and Close Gen will de-energise. Open Mains Pulse and Open Gen Pulse outputs will only
energise if the corresponding supply was on load before application of the Load Shed input.
When the Load Shed input is deactivated, the load will be transferred back to the supply that was disconnected
before application of the input.
Open Mains
Close Gen
Open Gen
Close Mains
30 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
NOTE : Generator Closed Auxiliary and Mains Closed Auxiliary inputs do not affect the operation of the
load switching in Breaker Scheme A
Activation of an input configured to mains load inhibit or generator load inhibit inputs cause the corresponding
breaker to be opened immediately. No other change in function will occur.
When the input is deactivated the load transfer scheme is followed as below.
If an input configured to Load Shed is activated, outputs set to Open Mains and Open Gen will energise, and inputs
configured to Close Mains and Close Gen will de-energise. Open Mains Pulse and Open Gen Pulse outputs will only
energise if the corresponding supply was on load before application of the Load Shed input.
When the Load Shed input is deactivated, the load will be transferred back to the supply that was disconnected
before application of the input.
When the load is about to be transferred, the check sync function is activated. When the mains and generator are
within the phase (25°) and frequency (1Hz) window the module transfers the load as shown below.
The module waits indefinitely for synchronisation unless Return to programmed transition is active in which case
after 2 minutes it performs a non-sync transfer as described in the previous section.
In sync
Open Mains
In sync
Close Gen
Open Gen
Close Mains
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 31
DSE Model 332 ATS Control and Instrumentation System Operators Manual
To open the mains breaker the Open Mains output energises, it then de-energises when the Mains Closed
Auxiliary indicates it has successfully opened, or after 1s whichever occurs first.
When the ‘Mains Closed Auxiliary’ indicates the mains breaker has opened, the transfer timer begins.
When the transfer timer expires, the module attempts to close the generator breaker by energising the Open Mains
and Close Generator outputs simultaneously, it then de-energises these outputs when the Generator Closed
Auxiliary input indicates it has successfully closed, or after 1s whichever occurs first.
To open the generator breaker the Open Gen output energises, it then de-energises when the Generator Closed
Auxiliary indicates it has successfully opened, or after 1s whichever occurs first.
When the ‘Generator Closed Auxiliary’ indicates the generator breaker has opened, the transfer timer begins.
When the transfer timer expires, the module attempts to close the mains breaker by energising the Open Gen and
Close Mains outputs simultaneously, it then de-energises these outputs when the Mains Closed Auxiliary input
indicates it has successfully closed, or after 1s whichever occurs first
When the Load Shed input is activated while the generator is closed the Open Gen output energises, it then de-
energises when the Generator Closed Auxiliary input indicates that it has successfully opened, or after 1s whichever
occurs first.
When the Load Shed input is activated while the mains is closed the Open Mains output energises, it then de-
energises when the Mains Closed Auxiliary input indicates that it has successfully opened, or after 1s whichever
occurs first.
When the Load shed input is de-energised the load will be returned to the supply that was disconnected, providing
that supply is healthy.
Close Gen
Open Gen
Close Mains
32 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
NOTE : The module waits indefinitely for synchronisation unless the ‘Return to programmed transition’
function is active in which case after 2 minutes it performs a non-sync transfer as described in the previous
section.
NOTE : The transfer time is ignored during a check-sync but is used if the transfer fails and it performs
a non-sync transfer.
When the module is about to transfer from mains to generator it activates the check sync function.
When the mains and generator are within the phase (25°) and frequency (1Hz) window the module energises the
Open Mains and Close Gen outputs simultaneously. These outputs are de-energised when the Generator Closed
Auxiliary input indicates it has successfully closed, or after 1s whichever occurs first.
When the module is about to transfer from generator to mains it activates the check sync function.
When the mains and generator are within the phase and frequency window the module energises the Open Gen and
Close Mains outputs simultaneously. These outputs are de-energised when the Generator Closed Auxiliary input
indicates it has successfully closed, or after 1s whichever occurs first.
When the Load Shed input is activated while the generator is closed the Open Gen output energises, it then de-
energises when the Generator Closed Auxiliary input indicates that it has successfully opened, or after 1s whichever
occurs first.
When the Load Shed input is activated while the mains is closed the Open Mains output energises, it then de-
energises when the Mains Closed Auxiliary input indicates that it has successfully opened, or after 1s whichever
occurs first.
When the Load shed input is de-energised the load will be returned to the supply that was disconnected, providing
that supply is healthy.
In Sync
Gen has closed
Open Mains
Close Gen
Open Gen
Close Mains
In Sync
Mains has closed
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 33
DSE Model 332 ATS Control and Instrumentation System Operators Manual
7 MODULE DISPLAY
7.1 BACKLIGHT
The backlight will be on if the unit has sufficient voltage on the power connection while the unit is turned on.
7.2 PROTECTIONS
7.2.1 GENERATOR
The 332 ATS module monitors the generator supply to ensure that it remains within configured levels. If the
generator supply fails, it is taken off load and the start/run signal is be removed.
Generator failure
The generator has not become available after the period of the Generator Failure timer has expired.
7.2.2 MAINS
Mains alarms signal that the mains supply is out of limits. In AUTO mode, the generator is called to start (if not
already running) and will be placed on load when available.
If the mains supply fails while the generator is running in MANUAL mode, the 332 ATS module transfers load to the
generator supply.
Should an input configured to Simulate Mains Available be active, the mains failure detection is inhibited.
Mains failure
Combined message to indicate the failure of the mains supply or activation of an input configured to Auxiliary Mains
Failure.
34 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
Plant battery alarms are Warning alarms only. The module displays the fault but no further action is taken.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 35
DSE Model 332 ATS Control and Instrumentation System Operators Manual
This configuration mode allows the operator limited customising of the way the module operates.
Use the module’s navigation buttons to traverse the menu and make value changes to the parameters:
Next page
Edit /Accept
value.
Press and hold
to exit editor.
36 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
To enter the ‘configuration mode’ press both the DOWN and INFO buttons together.
NOTE:- To exit the front panel configuration editor and activate your changes, press and hold the
button. Ensure you have saved any changes you have made by pressing the button first.
NOTE:- When the editor is visible, it is automatically exited after 5 minutes of inactivity to ensure
security.
When viewing the configuration editor, Press to select the required ‘page’ as listed below.
Front Panel Configuration Editor (Factory default settings are shown in bold italicised text)
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 37
DSE Model 332 ATS Control and Instrumentation System Operators Manual
Enter the editor as described above and press the button to access the
Scheduler page.
Press to enter edit mode and use the + / i buttons to make the
Schedulle function active. Press to save your change.
Press + to move to the next item.
Review the current setting and choose if the Scheduler is to perform an ‘on
load’ test (active) or ‘off load’ test (inactive)
38 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
If you require additional plugs from DSE, please contact our Sales department using the part numbers below.
The optional sealing gasket is not supplied with the controller but can be purchased separately.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 39
DSE Model 332 ATS Control and Instrumentation System Operators Manual
10 WARRANTY
DSE provides limited warranty to the equipment purchaser at the point of sale. For full details of any applicable
warranty, you are referred to your original equipment supplier (OEM).
11 DISPOSAL
11.1 WEEE (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
Directive 2002/96/EC
If you use electrical and electronic equipment you must store, collect, treat, recycle and dispose of
WEEE separately from your other waste.
Directive 2002/95/EC:2006
To remove specified hazardous substances (Lead, Mercury, Hexavalent Chromium, Cadmium, PBB & PBDE´s)
Exemption Note: Category 9. (Monitoring & Control Instruments) as defined in Annex 1B of the WEEE directive will
be exempt from the RoHS legislation. This was confirmed in the August 2005 UK´s Department of Trade and
Industry RoHS REGULATIONS Guide (Para 11).
Despite this exemption DSE has been carefully removing all non RoHS compliant components from our supply chain
and products.
When this is completed a Lead Free & RoHS compatible manufacturing process will be phased into DSE production.
This is a process that is almost complete and is being phased through different product groups.
40 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
12 APPENDIX
12.1 COMMUNICATIONS OPTION CONNECTIONS
12.1.1 DESCRIPTION
The DSE Configuration Suite software allows the controller to communicate with a PC. The computer connects to
the module as shown below and allows easy adjustment of the operating parameters and firmware update of the
controller.
NOTE:- The DC supply must be connected to the module for configuration by PC.
NOTE:- Refer to DSE Configuration Suite software Manual for further details on configuring the module
by PC.
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 41
DSE Model 332 ATS Control and Instrumentation System Operators Manual
12.2.1 IP CLASSIFICATIONS
IP65 (Front of module when module is installed into the control panel with the supplied sealing gasket).
IP42 (front of module when module is installed into the control panel WITHOUT being sealed to the panel)
Protection against contact and ingress of solid objects Protection against ingress of water
0 No protection 0 No protection
1 Protected against ingress solid objects with a 1 Protection against dripping water falling vertically. No
diameter of more than 50 mm. No protection against harmful effect must be produced (vertically falling drops).
deliberate access, e.g. with a hand, but large surfaces
of the body are prevented from approach.
2 Protected against penetration by solid objects with a 2 Protection against dripping water falling vertically. There
diameter of more than 12 mm. Fingers or similar must be no harmful effect when the equipment (enclosure)
objects prevented from approach. is tilted at an angle up to 15°from its normal pos ition
(drops falling at an angle).
3 Protected against ingress of solid objects with a 3 Protection against water falling at any angle up to 60°
diameter of more than 2.5 mm. Tools, wires etc. with a from the vertical. There must be no harmful effect (spray
thickness of more than 2.5 mm are prevented from water).
approach.
4 Protected against ingress of solid objects with a 4 Protection against water splashed against the equipment
diameter of more than 1 mm. Tools, wires etc. with a (enclosure) from any direction. There must be no harmful
thickness of more than 1 mm are prevented from effect (splashing water).
approach.
5 Protected against harmful dust deposits. Ingress of 5 Protection against water projected from a nozzle against
dust is not totally prevented but the dust must not enter the equipment (enclosure) from any direction. There must
in sufficient quantity to interface with satisfactory be no harmful effect (water jet).
operation of the equipment. Complete protection
against contact.
6 Protection against ingress of dust (dust tight). 6 Protection against heavy seas or powerful water jets.
Complete protection against contact. Water must not enter the equipment (enclosure) in harmful
quantities (splashing over).
42 Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM
DSE Model 332 ATS Control & Instrumentation System Operators Manual
NOTE: - There is no direct equivalence between IP / NEMA ratings. IP figures shown are approximate
only.
1 Provides a degree of protection against contact with the enclosure equipment and against a limited amount of falling dirt.
IP30
2 Provides a degree of protection against limited amounts of falling water and dirt.
IP31
3 Provides a degree of protection against windblown dust, rain and sleet; undamaged by the formation of ice on the enclosure.
IP64
3R Provides a degree of protection against rain and sleet:; undamaged by the formation of ice on the enclosure.
IP32
4 (X) Provides a degree of protection against splashing water, windblown dust and rain, hose directed water; undamaged by the formation
of ice on the enclosure. (Resist corrosion).
IP66
12/12K Provides a degree of protection against dust, falling dirt and dripping non corrosive liquids.
IP65
13 Provides a degree of protection against dust and spraying of water, oil and non corrosive coolants.
IP65
Part No. 057-095 332 Series OPERATING MANUAL ISSUE 1 10/06/2009 ADM 43