Professional Documents
Culture Documents
Video Copy Processor: Operation Manual
Video Copy Processor: Operation Manual
MODEL
P93W
P93E
OPERATION MANUAL
SIDE NOR 1:1 BRT PRINT
ADJUST BRT CONT FUNC FEED COPY
SIZE
CONT
MULTI SINGLE EXP.
MODE EXP.
OPEN
VIDEO COPY
PROCESSOR
This video copy processor complies with the requirements of the EC Directive 89/336/
EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gains proper
operation in residential areas, on business and light industrial premises and on small-
scale enterprises, inside as well as outside of the buildings. All places of operation are
characterised by their connection to the public low voltage power supply system.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communica-
tions.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interfer-
ence at his or her own expense.
Information:
This class A digital apparatus complies with Canadian ICES-003.
"CLASSIFIED BY UNDERWRITERS LABORATORIES INC.®
WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY IN
ACCORDANCE WITH UL2601-1 AND CAN/CSA C22.2 No. 601.1"
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
When you dispose of the unit or accessories, you must obey the law in the relative area
or country and/or regulation in the relative hospital.
WARNING:
Install and use this appliance in accordance with the operation manual for safety and
EMC (Electromagnetic Compatibility). If it is not installed and used in accordance with
the operation manual, it may cause interference to other equipment and/or other risk.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
In Europe, use the AC power cord according to the recommendations as below, in order
to comply with EN60601-1 and EN60950.
Connect to the 230V receptacle of the room or the host equipment.
The AC power cord should be VDE approved and consist of core size 1mm2 or bigger,
length 2.5m or shorter cord with IEC320/C13 type, 250V 10A or higher rating connector
and CEE(7)VII type or IEC 320-2.2/E type, 250V 10A or higher rating plug.
Use the video cable and/or the wired remote control according to the recommendations
as below, in order to comply with safety and EMC standards.
The video cable shall be 2m long or shorter, 75Ω coaxial, 3C-2VT or equivalent, with
BNC plug at each end.
The wired remote control shall be Mitsubishi Electric parts No. 939P951010. (2m long or
shorter, shielded wire, with 3.5mm diameter stereo mini-plug and switch box.)
This product is to be employed with medical equipment, just for reference purpose, not
for medical diagnostic purpose.
Information:
This equipment complies with EN55011, class B, group 1.
PROTECTIVE MEASURES
IF ABNORMALITIES ARISE, . . . DO NOT REMOVE THE CABINET
Use of the unit during emission of smoke or abnormal Touching internal parts is dangerous or may lead to
sounds (without adopting countermeasures) is malfunction. Contact the sales dealer to carry out inter-
dangerous. In such a case, unplug the power cord from nal checks and/or adjustments. Before opening the
the source outlet immediately, and request mainte- cover to clear a paper jam, etc., be sure to disconnect
nance services from the sales dealer. the power cord plug.
NEVER INSERT ANY OBJECT INTO THE UNIT DO NOT ATTACH A SCREW MORE THAN 6MM LONG
Foreign objects of any kind inserted into this unit constitute ON THE BOTTOM
a safety hazard and can cause extensive damage. If a screw more than 6 mm long is attached on the bottom
If any object should be inserted into the unit, unplug the of the printer, it may cause internal damage.
power cord, then contact the sales dealer.
PROTECT AGAINST DEW FORMATION
DO NOT PLACE ANYTHING ON THE UNIT In extremely cold regions, if the unit is moved quickly from
Heavy objects placed on the unit can cause damage or an extremely cold place to a warmer one, dew is likely to
obstruct proper ventilation. be formed. If dew is formed, printing is not possible.
INSTALLATION LOCATIONS
MAINTAIN GOOD VENTILATION PLACES LIKELY TO BE EXTREMELY HOT
Ventilation slots and holes are provided on sides of this Places exposed to direct sunlight, or near heating
unit. appliances can attain extremely high temperatures,
Place the unit on a hard and level surface and locate at which may deform the cabinet, or can become a
least 4" (10cm) from walls to ensure proper ventilation. prime cause of damage.
2
Downloaded from www.Manualslib.com manuals search engine
FOR LONG OPERATING LIFE
UNSUITABLE MATERIALS FOR THE UNIT WHEN A DEFECT IS FOUND
Many plastic components are used in the unit. If you detect smoke or other smell from the unit, discon-
Coat flaking and deformation are likely to occur if the nect immediately the power cord plug from a wall socket
unit is wiped with chemical dusters, benzine, thinner or and ask the agent for repair. It may dangerous to
any other solvent, if rubber or PVC items are left in operate the unit under these conditions.
contact with the unit for extended duration, or if the unit CONNECTION DEVICES
is sprayed with insecticide. Read thoroughly "Operating Precautions" of the instruc-
CARE OF THE CABINET tion booklets for the devices connected with the Video
Unplug and clean with a soft cloth slightly moistened Copy Processor.
with a mild soap and water solution. Allow to dry com- Do not disconnect the power cord during printing.
pletely before operating. Never use petroleum base CAUTION ON RELOCATING
solutions or abrasive cleaners. When transporting this unit, make sure it is not likely to
HEAD ABRASION be subjected to impacts. They can be a prime cause for
The thermal head, like the video head, wears out. damage. Further, make sure to disconnect the power
When it is abraded, it becomes hard to print out fine cord from the power outlet, and the cables from the
details of the picture. In such a case, it is necessary to connected devices.
replace the thermal head. Consult with the sales dealer UNPLUG THE POWER CORD DURING A LONG
for replacing the head. ABSENCE
Turn off the MAIN power switch and unplug the power
cord during a long absence.
THERMAL PAPER
2 Thermal papers listed in the page of SPECIFICA- 2 When the paper is rapidly transferred from a cool
TIONS are available. place to a hot place, a vapor or a dew is generated
2 When the remaining length of the paper is about10" on the paper surface causing paper jam or degraded
(25cm), a color belt appears at the paper end. printing quality.
Prepare for replacement of the paper. If the 2 A finger print or dust on the paper surface may
remaining paper length is less than 10" (25cm), degrade the printing quality.
printing becomes uneven due to the uneven
paper core surface. Note:
2 When the Printed paper is touched by wet hand, Mitsubishi brand thermal paper is specially treated
the print may be discolored. with an anti-static coating against thermal head
2 When the paper runs out during printing, the printing damage caused by static-electricity discharge.
operation stops and "EP" is displayed by the indicator The use of non-treated paper may cause premature
on the front panel. Install new paper at this time. head failure in your product.
2 Store the printed paper in a place with low humidity
free from a direct sunlight.
2 If the paper absorbs non-volatile organic solvents
(alcohol, ester, katone, etc.) the print may be
discolored.
Particularly, if the paper comes in contact with soft
vinyl chloride such as a transparent tape, it quickens
discoloration.
2 Do not use paper other than the specified one.
2 Immediately after the paper is replaced, 2-3 images
may be printed with a blank part due to hand's dust
or oil.
2 Avoid direct sunlight or places near heaters, etc.,
and store the paper in a place with 30°C ( 86°F)
or lower temperature and 35-80% RH.
3
Downloaded from www.Manualslib.com manuals search engine
SAFETY TECHNICAL CHECKS
Periods: According to the recommendations of the manufacturer of medical device.
Scope: a) Visual check
Housing, cables, operator controls, readout device ( displays, LED etc.), labels,
accessories, instruction manual.
b) Function test
Performance check acc. instruction manual, also unity and applicability of set
and accessory test.
c) Electrical check
Safety electrical test of the configuration in accordance with EN60601-1.
“ In the interest of safety, avoid the handling of liquids beside the set.”
The manufacturer, assembler, installer or importer considers himself responsible for the
effects on safety, reliability and performance of the EQUIPMENT only if:
– assembly operations, extensions, re-adjustments, modifications or repairs are carried out
by persons authorized by him, and
– the electrical installation of the relevant room complies with the IEC requirements
– the EQUIPMENT is used in accordance with the instructions for use.
• Any service after expiration of the warranty period will be chargeable. Consult your dealer
for advice.
TECHNICAL DESCRIPTION
The supplier will make available on request such circuit diagrams, component part lists,
descriptions, calibration instructions or other information which will assist the USER's ap-
propriately qualified technical personnel to repair those parts of the EQUIPMENT which
are classified by the manufacturer as repairable.
The use of ACCESSORY equipment not complying with the equivalent safety requirements
of this equipment may lead to a reduced level of safety of the resulting system. Consider-
ation relating to the choice shall include:
– use of the accessory in the PATIENT VICINITY
– evidence that the safety certification of the ACCESSORY has been performed in accor-
dance to the appropriate EN60601-1 and/or EN60601-1-1 harmonized national standard.
4
Downloaded from www.Manualslib.com manuals search engine
3 UNPACKING
Take the unit out of the box by the following procedures. Make sure to check the
contents.
1 Open the top of the box. 3 Take the unit out of the box carefully.
• Make sure to
keep the unit
horizontal.
MULTI
SINGLE EXP.
BRT
MODE ADJUST
CONT
BRT
EXP. CONT
FUNC FEED
COPY
Accessories
AC power cord
Thermal paper BNC/BNC connection cable
Wired remote control
Cleaning paper
Operation manual
5
Downloaded from www.Manualslib.com manuals search engine
4 FEATURES AND FUNCTIONS
Front Panel
1 23 4 5 6 7 8 9 A B C
SIDE NOR 1:1 BRT PRINT
ADJUST BRT CONT FUNC FEED COPY
SIZE
CONT
D
MULTI SINGLE EXP.
MODE EXP.
E OPEN
Reference
Name Function Page
1 Power switch Turns on/off the power. 12 • 31
6
Downloaded from www.Manualslib.com manuals search engine
Rear Panel
F G H I
REMOTE
ON
OFF
J
VIDEO
DIP SW FUNCTION TABLE
NO. 1 2 3 4 5 6
FUNCTION IMP TRAP MEMORY RESERVED
SW-ON 75Ω ON FIELD
SW-OFF HIGH OFF FRAME
K POTENTIAL
TERMINAL
EQUALIZATION
This is used to equalize the potential of the
equipment connected to this unit.
For details refer to the installation
instruction of equipment to be
connected.
7
Downloaded from www.Manualslib.com manuals search engine
5 INSTALLATION OF PAPER
Paper (High-density paper KP65HM-CE)
Moisture, fingerprints or dust on the
paper surface may cause a noise at
3 Pull out the paper end.
printing or deterioration in print
quality. Set the paper by the follow- • Pull out the first 15-
ing procedure to prevent adhesion 20cm (6 in. - 9 in.) of
of fingerprint or dust on the paper the paper to remove
surface. any slack in the roll.
printing side
cutter
INCORRECT CORRECT
Note: The printing surface is the outside. • Cut the paper end with the cutter by
Place the paper with the thermo- pulling the paper upwards against the
sensitive side (printing side) up. cutter blade.
When the paper roll is placed
inversely, images can not be printed.
8
Downloaded from www.Manualslib.com manuals search engine
When setting the paper, observe the following
precautions to prevent paper jam.
If the side of the print paper is uneven or the core is sticking out, the amount of paper feeding
after printing may vary.
When the side of paper is uneven or the core is sticking out, install the print paper after
making the paper side even.
The core is sticking out. Make the paper side even.
The paper is uneven.
INCORRECT CORRECT
CAUTION
• Keep the high-density paper away from fingerprint, dust or moisture when storing it.
• Do not touch the rubber roller. Do not stain or damage the roller surface.
• Do not touch the thermal head (located behind the cutter). When printing, the thermal
head is heated to high temperature.
• Do not touch the cutter blade.
9
Downloaded from www.Manualslib.com manuals search engine
6 EXAMPLE OF CONNECTION / SETTING OF SWITCHES
Connecting to various composite video signal equipment such
as medical equipment.
OUT terminal
Monitor
Setting of Switches
2 The following is an example of DIP switch setting.
2 Refer to page 29 for the DIP switch settings.
SW-NO. Setting
ON 1 75Ω
2 ON
OFF 3 FRAME
4 OFF
5 OFF
DIP SW 6 OFF
10
Downloaded from www.Manualslib.com manuals search engine
Medical Video Signal
1 Turn off the power switches of the Video copy processor and
the equipment to be connected.
2 Connect the VIDEO input terminal of the Video copy
processor to the video output terminal of the connected
equipment.
Rear panel
To VIDEO
output To VIDEO REMOTE
ON
Setting of Switches
Set the DIP switch as follows:
(This is standard setting.)
ON
SW-NO. Setting
OFF 1 75Ω
2 OFF
3 FRAME
DIP SW 4 OFF
5 OFF
DIP SW FUNCTION TABLE 6 OFF
NO. 1 2 3 4 5 6
FUNCTION IMP TRAP MEMORY RESERVED
SW-ON 75Ω ON FIELD
SW-OFF HIGH OFF FRAME
2 Select γ-curve " " - " " for ultrasonic diagnosis equipment.
Especially " " is recommended. Refer to the γ-curve set mode on page 17.
2 Refer to the " DIP SWITCH FUNCTIONS " on page 29 .
11
Downloaded from www.Manualslib.com manuals search engine
7 PRINTING
Printing Procedure
• Display a picture to
be printed on the When printing
monitor screen, and finishes, a
press the PRINT buzzer tone will
button. be heard.
Copy Printing
2 You can set the number of copies by
pressing the COPY button on the front
panel.
FEED COPY
You can copy the same picture as
many times as you desire by pressing
the COPY button.
When pressing the FEED button during
copy printing, the copy printing is
canceled upon completion of the
current copy.
Paper Feeding
2 To feed the paper, hold down the
FEED button on the front panel.
12
Downloaded from www.Manualslib.com manuals search engine
Use of Remote Control
Precautions on Printing
When dark pictures are printed consecutively, the Video Copy Processor may become
overheated and the indicator blinks.
In this case, wait for a while until the unit is cooled down.
Avoid pulling out or holding the paper during printing or copying to prevent paper jam.
Do not touch the paper until printing or copying finishes.
When printing is carried out with no signal input, "NO SIGNAL" will be printed at the bottom
of the print.
13
Downloaded from www.Manualslib.com manuals search engine
8 ADJUSTMENT OF PRINT PICTURE
Adjustment of Brightness/Contrast
You can adjust brightness and contrast of the printed picture
while observing the monitor screen.
Control panel
SIDE NOR 1:1 BRT
ADJUST BRT CONT FUNC FEED COPY
SIZE
CONT
MULTI SINGLE EXP.
MODE EXP.
SIZE
SIDE NOR 1:1
the brightness.
OPEN
• The BRT indicator lights up.
CONT
SIDE NOR 1:1 BRT PRINT
ADJUST BRT CONT FUNC FEED COPY
SIZE
MODE
MULTI SINGLE EXP.
CONT
EXP.
Press the CONT button " " to adjust
the contrast.
OPEN
• The CONT indicator lights up.
14
Downloaded from www.Manualslib.com manuals search engine
2 Change the setting. 3 Store the set value.
• Turn the control By pressing the PRINT button, the
clockwise to setting value is memorized.
ADJUST
increase the value. The memorized value will not be lost
even when the power is turned off.
15
Downloaded from www.Manualslib.com manuals search engine
9 SETTING FUNCTION MODE
Function mode
In this mode, the initial setting value of each function can be
changed. Each time the FUNC button is pressed, the mode is
switched as follows.
SIDE NOR 1:1 BRT PRINT
ADJUST BRT CONT FUNC FEED COPY
SIZE
CONT
MULTI SINGLE EXP.
MODE EXP.
OPEN
Stand-by status
DIRECTION setting
Selection of the memorized
multi image copy printing *1
SAVING setting
Setting of the horizontal print
area for the enlarged image *2 PAPER setting
16
Downloaded from www.Manualslib.com manuals search engine
Setting the function mode
ADJUST ADJUST
γ curve setting
Indicator Purpose and description
• To select the gamma (γ) curve (relation between the density and
the brightness of the image) to obtain an optimum density
depending on the connected device. Five options are available.
• The default setting is 5.
Selection of the memorized image for copy printing or the first image
for the multi image copy printing
Indicator Purpose and description
• You can select any image from the last 10 printed images to print
it again.
• The larger the number displayed by the indicator becomes, the
older the selected image is. (Selectable range : 0 to 9.)
• The selected image is displayed on the monitor. The image
selected in this mode is specified automatically as the first image
(the image printed on the right) for 2-multi image copy printing.
• The selected image is kept until a new image is memorized.
• The memorized images are cleared when the power is turned off.
17
Downloaded from www.Manualslib.com manuals search engine
Selection of the second image for the multi image copy printing
Indicator Purpose and description
• You can select any image from the last 10 printed images for 2-
multi image printing.
• The larger the number displayed by the indicator becomes, the
older the selected image is. (Selectable range : 0 to 9)
• The image selected in this mode is printed on the left for 2-multi
image copy printing.
• The selected image is displayed on the monitor.
• The selected image is kept until a new image is memorized.
• The memorized images are cleared when the power is turned off.
• You can specify the print area when the image is enlarged and
printed in NOR size.
• Because the print area is shown on the monitor, you can adjust
the print area viewing the monitor and shift the print area by
turning the ADJUST control.
• You can adjust the print area just horizontally in this mode. If you
expand the print area vertically, the whole image is enlarged.
• You can specify the print area when the image is enlarged and
printed in SIDE size.
• Because the print area is shown on the monitor, you can adjust
the print area viewing the monitor and shift the print area by
turning the ADJUST control.
• You can adjust the print area just vertically in this mode. If you
expand the print area horizontally, the whole image is enlarged.
18
Downloaded from www.Manualslib.com manuals search engine
Printing of the setting values
Indicator Purpose and description
• You can include the setting values of BRT, CONT and GAMMA
in the print at the bottom.
: The setting values are not printed.
: The setting values are printed.
,
SCAN setting
Indicator Purpose and description
,
A
(Underscan)
A
(Overscan)
IMAGE setting
Indicator Purpose and description
A A
(Positive print) (Negative print)
19
Downloaded from www.Manualslib.com manuals search engine
DIRECTION setting
Indicator Purpose and description
, A
A
(Normal) (Reverse)
SAVING setting
Indicator Purpose and description
• You can select the amount of paper for preparing a margin of the
next print.
: Normal margin
: Narrow margin
, Normal Narrow
PAPER setting
Indicator Purpose and description
• You can select any of the following options according to the paper
to be used.
: High glossy paper (KP91HG-CE)
: High density paper (KP65HM-CE, KP65H-CE)
, , : Standard paper (KP61B-CE, KP61S-CE)
20
Downloaded from www.Manualslib.com manuals search engine
PRINT button function setting
Indicator Purpose and description
• You can select the number of prints when you press the PRINT
button.
• The selectable number is to and (continuous printing).
• The continuous printing can be canceled by pressing the FEED
button.
- ,
• You can print the table of LED indications and the explanations
corresponding to each function mode.
• You can print the table by pressing the COPY button while is
displayed on the LED.
21
Downloaded from www.Manualslib.com manuals search engine
SIZE switch setting
The size of the printed image can be selected by the SIZE
switch.
SIDE NOR 1:1
SIZE
Example
A A
A
22
Downloaded from www.Manualslib.com manuals search engine
MODE switch setting
MODE switch works as the extended function of SIZE switch.
MODE
Set this switch to SINGLE for normal use. The image is printed in the size specified by the
SIZE switch.
When selecting EXP., you can enlarge or reduce the image to be printed in the NOR. size or
the SIDE size according to the setting of the SIZE switch.
• When EXP. is selected, the EXP. indicator lights up and the enlargement ratio is
displayed.
• The switch does not stay at the EXP. position. When you release the switch at the
EXP. position, it returns to the SINGLE position automatically.
• The enlargement ratio can be set from 0.5 to 2.0 by 0.1 steps.
• Use the ADJUST control to change the enlargement ratio.
• The fixed enlargement ratio will not be lost even when the power is turned off.
• When 1:1 is selected by the SIZE switch, printing of enlarged or reduced images is
not available.
23
Downloaded from www.Manualslib.com manuals search engine
Print patterns depending on the combination of the settings of
the SIZE and MODE switches
SIZE
SIDE NOR 1:1
MODE
SINGLE
A A A
A B
A
B
Printing is not
MULTI
available.
EXP.
A Printing is not
available.
24
Downloaded from www.Manualslib.com manuals search engine
User setting
This unit can memorize the settings which you adjusted to
meet the operating conditions of the connected devices and
the print quality conditions as the "user setting". When you
change the setting by mistake, you can correct it with a
simple operation.
Memorizing the user setting
1 The service personnel of this unit memorizes the settings. Contact your dealer.
25
Downloaded from www.Manualslib.com manuals search engine
10 ERROR DISPLAY
In case of an error in the unit during operation, you are warned
by an alarm tone or the LED indicator.
[Remedy]
Wait until the head cools down.
26
Downloaded from www.Manualslib.com manuals search engine
Cause/Error display Symptom/Remedy
2 No paper [Symptom]
• When the paper runs out or the paper is not installed, printing
becomes impossible and an alarm tone is heard.
In this case, all the buttons become invalid.
• If this error occurs while more than one copy is being printed or
there are images waiting to be processed, printing is cancelled
at the occurrence of the error.
[Remedy]
Install a new roll of paper according to "5. INSTALLATION OF
PAPER" on page 8.
When the paper is correctly installed while the printing of more than
one copy has been suspended or there are images waiting to be
processed, an alarm tone is heard. Then, the paper is fed automati-
cally about 15 cm and printing resumes.
After the error is resolved, the unit resumes printing from the inter-
rupted image and finishes printing all the outstanding images.
27
Downloaded from www.Manualslib.com manuals search engine
Cause/Error display Symptom/Remedy
4 Door error [Symptom]
• When the door opens, an alarm tone is heard.
The indicator displays " " for one second.
In this case, all the buttons become invalid.
• If this error occurs while more than one copy is being printed or
there are images waiting to be processed, printing is cancelled at
the occurrence of the error.
[Remedy]
Close the door.
When the door is closed while the printing of more than one copy
has been suspended or there are images waiting to be processed,
an alarm tone is heard and printing resumes.
After the error is resolved, the unit resumes printing from the
interrupted image and finishes printing all the outstanding images.
[Remedy]
Turn the power off. Then turn it on again.
Printing of the interrupted image or all the images saved in the
memory that are waiting to be processed is cancelled.
28
Downloaded from www.Manualslib.com manuals search engine
11 DIP SWITCH FUNCTIONS
ON
OFF
DIP SW
29
Downloaded from www.Manualslib.com manuals search engine
12 STATUS AND MODES
LED display Contents of right
Set state/Mode Video
Left Right side LED display output
30
Downloaded from www.Manualslib.com manuals search engine
13 USE OF CLEANING PAPER
When the thermal head is dirty with dust, etc., white spots or stripes may appear on the
print. In this case, clean the thermal head by the following procedure BY USING THE
SUPPLIED CLEANING PAPER.
3
FEED button until
Insert the cleaning paper. you hear a beep.
OPEN
Open the door.
Cleaning paper Take out the
cleaning paper.
CAUTION
0 It is recommended that after printing 10 rolls of paper the unit be cleaned using the supplied cleaning paper.
0 If the symptom of the dirty head is not corrected even after cleaning, your set needs repairing, contact your dealer.
0 Do not pull out the sheet and the cleaning paper while the door is closed.
This may cause extensive damage on the unit.
0 Never use other cleaning papers. It may cause damage to the thermal head.
0 This cleaning paper should be used only for cleaning the thermal head. Do not use it for other purpose.
31
Downloaded from www.Manualslib.com manuals search engine
14 MAINTENANCE
Turn off the power for maintenance.
When the rubber roller is dirty with dust, etc., a blank spot may
appear on the print.
In this case, eliminate the dust on to the rubber roller with a
blower or a brush.
Rubber roller
When the thermal head is dirty with dust, etc., white spots or
stripes may appear on the print.
In this case, clean the thermal head according to "13. USE OF
CLEANING PAPER".
Note: After installation of new roll of paper, dust on the paper will
generally require 2 to 3 prints to be made before the dust
is eliminated.
32
Downloaded from www.Manualslib.com manuals search engine
15 SPECIFICATIONS
Type: Video Copy Processor
Printing speed: 3.3 sec (Standard) (NTSC), 3.9 sec (Standard) (PAL)
SERVICE INFORMATION
Before requesting service please review this operation manual to correct minor complaints.
If you are unable to correct the problem, consult your MITSUBISHI Dealer or MITSUBISHI
Service Department.
33
Downloaded from www.Manualslib.com manuals search engine
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road, Irvine, CA 92618
Phone 949-465-6000
Mitsubishi Electric Europe B.V.
UK Branch
Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K.
Phone (0) 1707 276100 FAX (0) 1707 278755
German Branch
Gothaer Strasse 8, 40880 Ratingen ; Postfach 1548, 40835 Ratingen ; Germany
Phone (2102) 486-9250 FAX (2102) 486-7320
French Branch
25, Boulevard des Bouvets - 92741 NANTERRE cedex
Phone (01) 55.68.55.00 FAX (01) 55.68.57.31
Italian Branch
Centro Direzionale Colleoni, Palazzo Perseo-Ingresso 2,
Via Paracelso 12, 20041 Agrate Brianza, (Milano) Italy
Phone (039) 60531 FAX (039) 6057694
Benelux Branch
Nijverheidsweg 23 A, 3641 RP. Postbus 222, 3640 AE Mijdrecht
Phone 02972-82461 FAX 02972-83936