Professional Documents
Culture Documents
Chapter 13 Rotational Dynamics: Gravity, Which For Small Bodies (So That G
Chapter 13 Rotational Dynamics: Gravity, Which For Small Bodies (So That G
C.S. Forester
The African Queen
Introduction
The physical objects that we encounter in the world consist of collections of atoms that
are bound together to form systems of particles. When forces are applied, the shape of
the body may be stretched or compressed like a spring, or sheared like jello. In some
systems the constituent particles are very loosely bound to each other as in fluids and
gasses, and the distances between the constituent particles will vary. We shall begin our
study of extended objects by restricting ourselves to an ideal category of objects, rigid
bodies, which do not stretch, compress, or shear.
A body is called a rigid body if the distance between any two points in the body
does not change in time. Rigid bodies, unlike point masses, can have forces applied at
different points in the body. For most objects, treating as a rigid body is an idealization,
but a very good one. In addition to forces applied at points, forces may be distributed
over the entire body. Distributed forces are difficult to analyze; however, for example, we
regularly experience the effect of the gravitational force on bodies. Based on our
experience observing the effect of the gravitational force on rigid bodies, we note that the
gravitational force can be concentrated at a point in the rigid body called the center of
G
gravity, which for small bodies (so that g may be taken as constant within the body) is
identical to the center of mass of the body (we shall prove this fact in Appendix 13.A).
Let’s consider a rigid rod thrown in the air (Figure 13.1) so that the rod is
G
spinning as its center of mass moves with velocity v cm . Rigid bodies, unlike point-like
objects, can have forces applied at different points in the body. We have explored the
physics of translational motion; now, we wish to investigate the properties of rotation
exhibited in the rod’s motion, beginning with the notion that every particle is rotating
about the center of mass with the same angular (rotational) velocity.
1
The authors of these notes suspect either a math error on Mr. Forester’s part or an oversight by his editors.
8/25/2008 1
Figure 13.1 The center of mass of a thrown rigid rod follows a parabolic trajectory while
the rod rotates about the center of mass.
We can use Newton’s Second Law to predict how the center of mass will move.
Since the only external force on the rod is the gravitational force (neglecting the action of
air resistance), the center of mass of the body will move in a parabolic trajectory.
How was the rod induced to rotate? In order to spin the rod, we applied a torque
with our fingers and wrist to one end of the rod as the rod was released. The applied
torque is proportional to the angular acceleration. The constant of proportionality is
called the moment of inertia. When external forces and torques are present, the motion of
a rigid body can be extremely complicated while it is translating and rotating in space.
We shall begin our study of rotating objects by considering the simplest example of rigid
body motion, rotation about a fixed axis.
When we studied static equilibrium, we demonstrated the need for two conditions: The
total force acting on an object is zero, as is the total torque acting on the object. If the
total torque is non-zero, then the object will start to rotate.
A simple example of rotation about a fixed axis is the motion of a compact disc in
a CD player, which is driven by a motor inside the player. In a simplified model of this
motion, the motor produces angular acceleration, causing the disc to spin. As the disc is
set in motion, resistive forces oppose the motion until the disc no longer has any angular
acceleration, and the disc now spins at a constant angular velocity. Throughout this
process, the CD rotates about an axis passing through the center of the disc, and is
perpendicular to the plane of the disc (see Figure 13.2). This type of motion is called
fixed-axis rotation.
8/25/2008 2
Figure 13.2 Rotation of a compact disc about a fixed axis.
When we ride a bicycle forward, the wheels rotate about an axis passing through
the center of each wheel and perpendicular to the plane of the wheel (Figure 13.3). As
long as the bicycle does not turn, this axis keeps pointing in the same direction. This
motion is more complicated than our spinning CD because the wheel is both moving
G
(translating) with some center of mass velocity, v cm , and rotating.
Figure 13.3 Fixed axis rotation and center of mass translation for a bicycle wheel.
When we turn the bicycle’s handlebars, we change the bike’s trajectory and the
axis of rotation of each wheel changes direction. Other examples of non-fixed axis
rotation are the motion of a spinning top, or a gyroscope, or even the change in the
direction of the earth’s rotation axis. This type of motion is much harder to analyze, so
we will restrict ourselves in this chapter to considering fixed axis rotation, with or
without translation.
8/25/2008 3
dθ
ω≡ , (13.1.1)
dt
d 2θ
α≡ . (13.1.2)
dt 2
For a rigid body undergoing fixed-axis rotation, we can divide the body up into
small volume elements with mass Δmi . Each of these volume elements is moving in a
circle of radius r⊥,i about the axis of rotation (Figure 13.4).
We will adopt the notation implied in Figure 13.4, and denote the vector from the axis to
G G
the point where the mass element is located as r⊥,i , with r⊥, i = r⊥,i .
Because the body is rigid, all the volume elements will have the same angular velocity ω
and hence the same angular acceleration α . If the bodies did not have the same angular
velocity, the volume elements would “catch up to” or “pass” each other, precluded by the
rigid-body assumption.
8/25/2008 4
Figure 13.5 Sign conventions for rotational motion.
If the rigid body rotates in the counterclockwise direction, then the angular velocity is
positive, ω ≡ dθ dt > 0 . If the rigid body rotates in the clockwise direction, then the
angular velocity is negative, ω ≡ dθ dt < 0 .
• If the rigid body increases its rate of rotation in the counterclockwise (positive)
direction then the angular acceleration is positive, α ≡ d 2θ dt 2 = dω / dt > 0 .
• If the rigid body decreases its rate of rotation in the counterclockwise (positive)
direction then the angular acceleration is negative, α ≡ d 2θ dt 2 = dω / dt < 0 .
• If the rigid body increases its rate of rotation in the clockwise (negative) direction
then the angular acceleration is negative, α ≡ d 2θ dt 2 = dω / dt < 0 .
• If the rigid body decreases its rate of rotation in the clockwise (negative) direction
then the angular acceleration is positive, α ≡ d 2θ dt 2 = dω / dt > 0 .
To phrase this more generally, if α and ω have the same sign, the body is speeding up;
if opposite signs, the body is slowing down. This general result is independent of the
choice of positive direction of rotation.
Note that in Figure 13.2, the CD has a negative angular velocity as viewed from above;
CDs do not operate the same way record player turntables do.
vtan, i = r⊥ , i ω . (13.1.3)
8/25/2008 5
If the magnitude of the tangential velocity is changing, the volume element undergoes a
tangential acceleration given by
Recall from Chapter 6.3 Equation (6.3.14) that the volume element is always accelerating
inward with magnitude
2
vtan,
arad, i = i
= r⊥, i ω 2 . (13.1.5)
r⊥ , i
A turntable is a uniform disc of mass 1.2 kg and a radius 1.3 × 101 cm . The turntable is
spinning initially at a constant rate of f 0 = 33 cycles ⋅ min −1 ( 33 rpm ). The motor is
turned off and the turntable slows to a stop in 8.0 s . Assume that the angular acceleration
is constant.
Answer:
⎛ cycles ⎞ ⎛ 1min ⎞ −1
f 0 = ⎜ 33 ⎟⎜ ⎟ = 0.55 cycles ⋅ s = 0.55 Hz , (13.1.6)
⎝ min ⎠ ⎝ 60 s ⎠
⎛ radian ⎞ ⎛ cycles ⎞
ω0 = 2π f 0 = ⎜ 2π ⎟⎜ 0.55
−1
⎟ = 3.5 rad ⋅ s . (13.1.7)
⎝ cycle ⎠ ⎝ s ⎠
Δω ω f − ω 0 −3.5 rad ⋅ s −1
α= = = = −4.3 × 10−1 rad ⋅ s −2 . (13.1.8)
Δt t f − t0 8.0 s
8/25/2008 6
13.2 Torque
In order to understand the rotation of a rigid body we must introduce a new quantity, the
G G G
torque. Let a force FP with magnitude F = FP act at a point P . Let rS , P be the vector
G
from the point S to a point P , with magnitude r = rS , P . The angle between the vectors
G G
rS , P and FP is θ with [0 ≤ θ ≤ π ] (Figure 13.6).
G G G
τ S = rS , P × FP . (13.2.1)
(See section 2.5 for a review of the definition of the cross product of two vectors). The
G
magnitude of the torque about a point S due to force FP acting at P , is given by
τ S = r F sin θ . (13.2.2)
The SI units for torque are [N ⋅ m] . The direction of the torque is perpendicular to the
G G
plane formed by the vectors rS , P and FP (for [0 < θ < π ] ), and by definition points in
the direction of the unit normal vector to the plane nˆ RHR as shown in Figure 13.7.
8/25/2008 7
Recall that the magnitude of a cross product is the area of the parallelogram (the height
times the base) defined by the two vectors. Figure 13.8 shows the two different ways of
G G
defining height and base for a parallelogram defined by the vectors rS , P and FP .
We can interpret the quantity r⊥ as follows. We begin by drawing the line of action of the
G
force FP . This is a straight line passing through P , parallel to the direction of the force
G
FP . Draw a perpendicular to this line of action that passes through the point S (Figure
13.9). The length of this perpendicular, r⊥ = r sin θ , is called the moment arm about the
G
point S of the force FP .
8/25/2008 8
Figure 13.9 The moment arm about the point S associated with a force acting at the
point P is the perpendicular distance from S to the line of action of the force passing
through the point P
2. Torque is a vector whose direction and magnitude depend on the choice of a point
S about which the torque is calculated.
3. The direction of torque is perpendicular to the plane formed by the two vectors,
G G
FP and r = rS , P (the vector from the point S to a point P ).
8/25/2008 9
It’s important to note that the terms “clockwise” and “counterclockwise” might be
G G
different for different observers. For instance, if the plane containing FP and rS , P is
horizontal, an observer above the plane and an observer below the plane would assign
disagree on the two terms. For a vertical plane, the directions that two observers on
opposite sides of the plane would be mirror images of each other, and so again the
observers would disagree.
2. Suppose we choose clockwise as positive. Then we assign a negative sign for the
torque in Figure 13.10b since the torque is directed opposite to the unit
normal nˆ LHR .
With rare exceptions, these notes will take the counterclockwise direction to be positive.
Consider the forces that act on the rotating body. Most generally, the forces on different
volume elements will be different, and so we will denote the force on the volume element
G
of mass Δmi by Fi .
Choose the z -axis to lie along the axis of rotation. As in Section 13.1, divide the body
into volume elements of mass Δmi . Let the point S denote a specific point along the axis
of rotation (Figure 13.11). Each volume element undergoes a tangential acceleration as
G
the volume element moves in a circular orbit of radius r⊥,i = r⊥,i about the fixed axis.
8/25/2008 10
Figure 13.11 Volume element undergoing fixed-axis rotation about the z -axis.
where zi is the distance along the axis of rotation between the point S and the volume
G
element. The torque about S due to the force Fi acting on the volume element is
given by
G G G
τ S , i = rS , i × Fi . (13.3.2)
For fixed-axis rotation, we are interested in the z -component of the torque, which must
be the term
G
(τ ) = ( r
S, i z ⊥,i r
ˆ × F i ) z
(13.3.4)
G
since the cross product zi kˆ × Fi must be directed perpendicular to the plane formed by
G
the vectors k̂ and Fi , hence perpendicular to the z -axis.
The total force acting on the volume element has components
8/25/2008 11
G
Fi = Fradial, i rˆ + Ftan, i θˆ + Fz , i kˆ . (13.3.5)
The z -component Fz , i of the force cannot contribute a torque in the z -direction, and so
substituting Equation (13.3.5) into Equation (13.3.4) yields
(τ )
S ,i z ( (
= r⊥ , i rˆ × Fradial, i rˆ + Ftan, i θˆ )) .
z
(13.3.6)
The radial force does not contribute to the torque about the z -axis, since
G
r⊥ , i rˆ × Fradial, i rˆ = 0 . (13.3.7)
So, we are interested in the contribution due to torque about the z -axis due to the
tangential component of the force on the volume element (Figure 13.12). The component
of the torque about the z -axis is given by
(τ ) = ( r
S, i z ⊥,i rˆ × Ftan, i θˆ ) z
= r⊥ ,i Ftan, i . (13.3.8)
The z -component of the torque is directed out of the page in Figure 13.12, where Ftan,i
is positive (the tangential force is directed counterclockwise, as in the figure).
From Equation (13.3.8), the component of the torque about the z -axis is then given by
8/25/2008 12
(τ ) = r⊥ , i Ftan, i = Δmi ( r⊥ , i ) α .
2
S ,i z (13.3.11)
The total component of the torque about the z -axis is the summation of the torques on all
the volume elements,
i= N i= N
(τ ) = (τ ) + (τ )
total
S z S ,1 z S ,2 z + ⋅⋅⋅ = ∑ (τ S , i ) = ∑ r⊥, i Ftan, i
z
i =1 i =1
i= N
(13.3.12)
= ∑ Δmi ( r⊥, i ) α .
2
i =1
Since each element has the same angular acceleration, α , the summation becomes
⎛ i=N 2⎞
(τ )
total
S = ⎜ ∑ Δmi ( r⊥ , i ) ⎟α . (13.3.13)
z
⎝ i=1 ⎠
The quantity
i= N
I S = ∑ Δmi ( r⊥, i ) .
2
(13.3.14)
i =1
is called the moment of inertia of the rigid body about a fixed axis passing
through the point S , and is a physical property of the body. The SI units for
moment of inertia are ⎡⎣ kg ⋅ m 2 ⎤⎦ .
Thus Equation (13.3.13) shows that the z -component of the torque is proportional to the
angular acceleration,
(τ )
total
S z
= IS α , (13.3.15)
This is very similar to Newton’s Second Law: the total force is proportional to the
acceleration,
G G
F total = m totala . (13.3.16)
8/25/2008 13
For a continuous mass distribution, the summation becomes an integral over the body
IS = ∫ dm ( r⊥ ) ,
2
(13.3.17)
body
The turntable in Example 13.1.1, of mass 1.2 kg and radius 1.3 × 101 cm , has a moment
of inertia I S = 1.01× 10−2 kg ⋅ m 2 about an axis through the center of the disc and
perpendicular to the disc. The turntable is spinning at an initial constant frequency of
f 0 = 33 cycles ⋅ min −1 . The motor is turned off and the turntable slows to a stop in 8.0 s
due to frictional torque. Assume that the angular acceleration is constant. What is the
magnitude of the frictional torque acting on the disc?
Answer:
We have already calculated the angular acceleration of the disc in Example 13.1.1, where
we found that the angular acceleration is
Δω ω f − ω 0 −3.5 rad ⋅ s −1
α= = = = −4.3 × 10−1 rad ⋅ s −2 (13.3.18)
Δt t f − t0 8.0 s
τ friction
total
= I S α = (1.01× 10−2 kg ⋅ m 2 )( 4.3 ×10−1 rad ⋅ s −2 )
(13.3.19)
= 4.3×10−3 N ⋅ m.
Consider a thin uniform rod of length L and mass m . In this problem, we will calculate
the moment of inertia about an axis perpendicular to the rod that passes through the
center of mass of the rod. A sketch of the rod, volume element, and axis is shown in
Figure 13.13.
Choose Cartesian coordinates, with the origin at the center of mass of the rod, which is
midway between the endpoints since the rod is uniform. Choose the x -axis to lie along
the length of the rod, with the positive x -direction to the right, as in the figure.
8/25/2008 14
Figure 13.13 Moment of inertia of a uniform rod about center of mass.
When the rod rotates about an axis perpendicular to the rod that passes through the center
of mass of the rod, the element traces out a circle of radius r⊥ = x .
L2
x3
∫ (r ) dm = λ ∫ ( x ) dx = λ
L/2
I cm =
2 2
⊥ −L/ 2
body
3 −L 2 (13.3.20)
m ( L 2) m (− L 2)
3
1 3
= − = m L2 .
L 3 L 3 12
By using a constant mass per unit length along the rod, we need not consider variations in
the mass density in any direction other than the x - axis. We also assume that the width is
the rod is negligible. (Technically we should treat the rod as a cylinder or a rectangle in
the x-y plane if the axis is along the z - axis. The calculation of the moment of inertia in
these cases would be more complicated.)
Consider a rigid body of mass m undergoing fixed-axis rotation. Consider two parallel
axes. The first axis passes through the center of mass of the body, and the moment of
inertia about this first axis is I cm . The second axis passes through some other point S in
the body. Let d S ,cm denote the perpendicular distance between the two parallel axes
(Figure 13.14). Then the moment of inertia I S about an axis passing through a point S is
related to I cm by
I S = I cm + m d S2,cm . (13.4.1)
8/25/2008 15
Figure 13.14 Geometry of the parallel axis theorem.
Identify an infinitesimal volume element of mass dm . The vector from the point S to the
G G
mass element is rS , dm , the vector from the center of mass to the mass element is rcm, dm ,
G
and the vector from the point S to the center of mass is rS ,cm . From Figure 13.14, we
see that
G G G
rS , dm = rS ,cm + rcm, dm . (13.4.2)
The notation gets complicated at this point. We are interested in distances from the
respective axes, so denote the following vectors as motivated in Section 13.2:
G
• As in Figure 13.14 and Equation (13.4.2), rcm, dm is the vector from the center of
mass to the position of the mass element of mass dm . This vector has a
G
component vector rcm, & , dm parallel to the axis through the center of mass and a
G
component vector rcm, ⊥ , dm perpendicular to the axis through the center of mass.
The magnitude of the perpendicular component vector is
G
rcm, ⊥ , dm = rcm, ⊥ , dm . (13.4.3)
G
• As in Figure 13.9 and Equation (13.4.2), rS , dm is the vector from the point S to
the position of the mass element of mass dm . This vector has a component
G
vector rS , & , dm parallel to the axis through the point S and a component vector
8/25/2008 16
G
rS , ⊥ , dm perpendicular to the axis through the point S . The magnitude of the
perpendicular component vector is
G
rS , ⊥ , dm = rS , ⊥ , dm . (13.4.4)
G
• As in Figure 13.14 and Equation (13.4.2), rS ,cm is the vector from the point S to
G
the center of mass. This vector has a component vector rS ,& ,cm parallel to both
G G
axes and a perpendicular component vector rS ,⊥ ,cm of rS ,cm perpendicular to both
axes (the axes are parallel, of course). The magnitude of the perpendicular
component vector is
G
rS ,⊥ ,cm = d S ,cm . (13.4.5)
At this point, note that if we had simply decided that the two parallel axes are parallel to
the z -direction, we could have saved some steps and perhaps spared some of the notation
with the triple subscripts. However, we want a more general result, one valid for cases
where the axes are not fixed, or when different objects in the same problem have different
axes. For example, consider the turning bicycle, for which the two wheel axes will not be
parallel, or a spinning top that precesses (wobbles). Such cases will be considered in
Chapter 16, and we will show the general case of the parallel axis theorem in anticipation
of use for more general situations.
∫ dm ( rS , ⊥ ,dm ) .
2
IS = (13.4.7)
body
G G
(r )
2
S , ⊥ ,dm = rS , ⊥ ,dm ⋅ rS , ⊥ ,dm
G G G G
= ( rS , ⊥ ,cm + rcm, ⊥ ,dm ) ⋅ ( rS , ⊥ ,cm + rcm, ⊥ ,dm ) (13.4.8)
G G
= d S2,cm + ( rcm,⊥ , dm ) + 2 rS , ⊥ ,cm ⋅ rcm, ⊥ ,dm .
2
8/25/2008 17
G G
∫ dm ( d S2,cm ) + ∫ dm ( rcm, ⊥ ,dm ) + 2 ∫ dm ( rS ,⊥ ,cm ⋅ rcm, ⊥ ,dm ) .
2
IS = (13.4.9)
body body body
In the first integral in Equation (13.4.9), rS ,⊥,cm = d S ,cm is the distance between the parallel
axes and is a constant and may be taken out of the integral, and
The second term in Equation (13.4.9) is the moment of inertia about the axis through the
center of mass,
∫ dm ( rcm, ⊥ ,dm ) .
2
I cm = (13.4.11)
body
G
The third integral in Equation (13.4.9) is zero. To see this, note that the term rS ,⊥,cm is a
constant and may be taken out of the integral,
G G G G
2 ∫ dm ( rS , ⊥ ,cm ⋅ rcm, ⊥ ,dm ) = rS ,⊥ ,cm ⋅ 2 ∫ dm ( rcm, ⊥ ,dm ) (13.4.12)
body body
G
The integral ∫ dm ( rcm,⊥ , dm ) is the perpendicular component of the position of the center
body
G
of mass with respect to the center of mass, and hence 0 , with the result that
G G
2 ∫ dm ( rS ,⊥ cm ⋅ rcm,⊥ , dm ) = 0 . (13.4.13)
body
Thus, the moment of inertia about S is just the sum of the first two integrals in
Equation (13.4.9),
I S = I cm + m d S2,cm . (13.4.14)
Let point S be the left end of the rod of Example 13.2.1 and Figure 13.13. Then the
distance from the center of mass to the end of the rod is d S ,cm = L / 2 . The moment of
inertia I S = I end about an axis passing through the endpoint is related to the moment of
8/25/2008 18
inertia about an axis passing through the center of mass, I cm = (1/12) m L2 , according to
Equation (13.4.14),
1 1 1
IS = m L2 + m L2 = m L2 . (13.4.15)
12 4 3
In this case it’s easy and useful to check by direct calculation. Use Equation (13.3.20)
but with the limits changed to x′ = 0 and x′ = L , where x′ = x + L / 2 ;
L
I end = ∫
body
r⊥ 2 dm = λ ∫ x′2 dx′
0
L (13.4.16)
x′3 m ( L)3 m (0)3 1
=λ = − = m L2 .
3 0
L 3 L 3 3
Simple Pendulum
A pendulum consists of an object hanging from the end of a string or rigid rod pivoted
about the point S . The object is pulled to one side and allowed to oscillate. If the object
has negligible size and the string or rod is massless, then the pendulum is called a simple
pendulum. The force diagram for the simple pendulum is shown in Figure 13.15.
8/25/2008 19
The string or rod exerts no torque about the pivot point S . The weight of the object has
radial r̂ - and θ̂ - components given by
G
(
mg = mg cosθ rˆ − sin θ θˆ ) (13.5.1)
G G G
( )
τ S = rS , m × m g = l rˆ × m g cosθ rˆ − sin θ θˆ = −l m g sin θ kˆ (13.5.2)
and so the component of the torque in the z -direction (into the page in Figure 13.15 for
θ positive, out of the page for θ negative) is
I S = ml 2 . (13.5.4)
d 2θ
(τ S ) z = I Sα = I S
dt 2
(13.5.5)
d 2θ
− mgl sin θ = ml 2
.
dt 2
d 2θ g
2
= − sin θ . (13.5.6)
dt l
When the angle of oscillation is small, then we can use the small angle approximation
sin θ ≅ θ ; (13.5.7)
d 2θ g
2
≅− θ . (13.5.8)
dt l
8/25/2008 20
This equation is similar to the object-spring simple harmonic oscillator differential
equation from Chapter 10.2, Equation 10.2.3,
d 2x k
2
=− x, (13.5.9)
dt m
which describes the oscillation of a mass about the equilibrium point of a spring. Recall
that in Chapter 10.2, Equation 10.2.7, the angular frequency of oscillation was given by
k
ωspring = . (13.5.10)
m
g
ωpendulum ≅ , (13.5.11)
l
with period
2π l
T= ≅ 2π . (13.5.12)
ωpendulum g
A procedure for determining the period for larger angles is given in Appendix 13.B.
Physical Pendulum
A physical pendulum consists of a rigid body that undergoes fixed axis rotation about a
fixed point S (Figure 13.16). The gravitational force acts at the center of mass of the
physical pendulum (Appendix 13.A). Suppose the center of mass is a distance lcm from
the pivot point S .
8/25/2008 21
Figure 13.16 Physical pendulum.
The analysis is nearly identical to the simple pendulum. The torque about the pivot point
is given by
G G G
( )
τ S = rS ,cm × m g = lcmrˆ × m g cosθ rˆ − sin θ θˆ = −lcm m g sin θ kˆ . (13.5.13)
Following the same steps that led from Equation (13.5.2) to Equation (13.5.6), the
rotational dynamical equation for the physical pendulum is
d 2θ
(τ S ) z = I Sα = I S
dt 2
(13.5.14)
d 2θ
− mglcm sin θ = I S 2 .
dt
d 2θ mglcm
2
=− sin θ . (13.5.15)
dt IS
As with the simple pendulum, for small angles sin θ ≈ θ and Equation (13.5.15) reduces
to the simple harmonic oscillator equation with angular frequency
mg lcm
ω pendulum ≈ (13.5.16)
IS
and period
2π IS
Tphysical = ≅ 2π . (13.5.17)
ω pendulum m g lcm
It is sometimes convenient to express the moment of inertia about the pivot point in terms
of lcm and I cm using the parallel axis theorem in Equation (13.4.14), with d S ,cm ≡ lcm ,
I S = I cm + mlcm
2
, with the result
lcm I
Tphysical ≅ 2π + cm . (13.5.18)
g m g lcm
8/25/2008 22
Thus, if the object is “small” in the sense that I cm mlcm
2
, the expressions for the
physical pendulum reduce to those for the simple pendulum. Note that this is not the case
shown in Figure 13.16.
Introduction
When a constant torque τ S is applied to an object, and the object rotates through an angle
Δθ about an axis through the center of mass, then the torque does an amount of work
ΔW = τ S Δθ on the object. By extension of the linear work-energy theorem, the amount
of work done is equal to the change in the rotational kinetic energy of the object,
1 1
Wrot = I cmω 2f − I cmω 02 = K rot, f − K rot,0 . (13.6.1)
2 2
The rate of doing this work is the rotational power exerted by the torque,
dWrot ΔWrot dθ
Prot ≡ = lim =τS =τS ω . (13.6.2)
dt Δt →0 Δt dt
Rotational work
Consider a rigid body rotating about an axis. Each small element of mass Δmi in the rigid
body is moving in a circle of radius ( rS , ⊥ ) about the axis of rotation passing through the
i
point S . Each mass element undergoes a small angular displacement Δθ under the
G
action of a tangential force, Ftan, i = Ftan, i θˆ , where θ̂ is the unit vector pointing in the
tangential direction (Figure 13.7). The element will then have an associated displacement
G
vector for this motion, ΔrS , i = ( rS , i ) Δθ θˆ and the work done by the tangential force is
⊥
G G
( )( )
ΔWi = Ftan ,i ⋅ ΔrS , i = Ftan, i θˆ ⋅ ( rS , i ) Δθ θˆ = Ftan, i ( rS , i ) Δθ .
⊥ ⊥
(13.6.3)
Applying Newton’s Second Law to the element Δmi in the tangential direction,
Using the expression in Equation (13.1.4) for tangential acceleration we have that
8/25/2008 23
Ftan, i = Δmi ( rS , i ) α . (13.6.5)
⊥
ΔWi = Δmi ( rS , i ) α Δθ .
2
(13.6.6)
⊥
Summing the rotational work done on all of the mass elements, we obtain
⎛ 2 ⎞
ΔW = ∑ ΔWi = ⎜ ∑ Δmi ( rS , i ) ⎟α Δθ . (13.6.7)
⊥
i ⎝ i ⎠
In the limit that the discrete mass elements become infinitesimal continuous mass
elements, Δmi → dm , the summation becomes an integral over the body:
⎛ 2 ⎞ ⎛ 2 ⎞
ΔW = ⎜ ∑ Δmi ( rS , i ) ⎟α Δθ → ⎜ ∫ dm ( rS )⊥ ⎟α Δθ . (13.6.8)
⎝ i ⊥
⎠ ⎜ body ⎟
⎝ ⎠
Since the integral in this expression is just the moment of inertia about a fixed axis
passing through the point S , we have for the rotational work
ΔW = I S α Δθ . (13.6.9)
Since the z -component of the torque (in the direction along the axis of rotation) about S
is given by
(τ S ) z = I S α , (13.6.10)
the rotational work is the product of the torque and the angular displacement,
ΔW = (τ S ) z Δθ . (13.6.11)
Recall the result of Equation (13.3.8) that the component of the torque (in the direction
G
along the axis of rotation) about S due to the tangential force, Ftan,i , acting on the mass
element Δmi is
(τ )
S ,i z = Ftan, i ( rS , i ) ,
⊥
(13.6.12)
8/25/2008 24
(τ S ) z = ∑ (τ S ,i ) z = ∑ Ftan,i ( rS ,i )⊥ (13.6.13)
i i
dW = (τ S ) z dθ . (13.6.15)
We can integrate this amount of rotational work as the angle coordinate of the rigid body
changes from some initial value θ = θ 0 to some final value θ = θ f ,
θf
W = ∫ dW = ∫
θ0
(τ S ) z dθ . (13.6.16)
The general motion of a rigid body consists of a translation of the center of mass with
G
velocity v cm and a rotation about the center of mass with angular velocity ωcm .
Having defined translational kinetic energy in Chapter 7.2, Equation 7.2.1, we now
define the rotational kinetic energy for a rigid body about its center of mass. Each
individual mass element Δmi undergoes circular motion about the center of mass with
angular frequency ωcm in a circle of radius ( rcm, i ) . Therefore the velocity of each
⊥
G
element is given by v cm, i = ( rcm, i ) ωcm θ . The rotational kinetic energy is then
ˆ
⊥
We now add up the kinetic energy for all the mass elements,
⎛ 1 2 ⎞ 2 ⎛1 2 ⎞ 2
K cm = ∑ K cm, i = ⎜ ∑ Δmi ( rcm, i ) ⎟ ωcm = ⎜ ∫ dm ( rcm )⊥ ⎟ ωcm
⎝ i 2 ⊥
⎠ ⎜ 2 body ⎟
i ⎝ ⎠ (13.6.18)
1
= I cm ωcm
2
.
2
The total kinetic energy is the sum of the translational kinetic energy and the rotational
kinetic energy,
8/25/2008 25
1 1
K total = K trans + K rot = m vcm
2
+ I cmωcm
2
. (13.6.19)
2 2
The above assertion that the total kinetic energy consists of two parts, which is certainly
plausible, is derived in Appendix 13.C.
We will now show that the rotational work is equal to the change in rotational kinetic
energy. We begin by substituting our result from Equation (13.6.10) into Equation
(13.6.15) for the infinitesimal rotational work,
dWrot = I S α dθ . (13.6.20)
Recall that the rate of change of angular velocity is equal to the angular acceleration,
α ≡ dω dt and that the angular velocity is ω ≡ dθ dt . Note that in the limit of small
displacements,
dω dθ
dθ = dω = dω ω . (13.6.21)
dt dt
dω dθ
dWrot = I S α dθ = I S dθ = I S dω = I S dω ω . (13.6.22)
dt dt
We can integrate this amount of rotational work as the angular velocity of the rigid body
changes from some initial value ω = ω0 to some final value ω = ω f ,
ωf 1 1
Wrot = ∫ dWrot = ∫ I S dω ω = I S ω 2f − I S ω02 . (13.6.23)
ω0 2 2
When a rigid body is rotating about a fixed axis passing through a point S in the body,
there is both rotation and translation about the center of mass unless S is the center of
mass. If we choose the point S in the above equation for the rotational work to be the
center of mass, then
1 1
Wrot = I cmωcm,
2
f − I cmωcm,0
2
= K rot, f − K rot,0 ≡ ΔK rot . (13.6.24)
2 2
Recall the work-kinetic energy theorem stated that the total translational work done by all
the forces is equal to the change in the translational kinetic energy of the center of mass,
8/25/2008 26
1 2 1 2
Wtrans = mvcm, f − mvcm,0 ≡ ΔK trans . (13.6.25)
2 2
Since we did not include the effect of rotational work in Equation (13.6.25), we now add
the two contributions to the total work and find that the total work done on a rigid body is
equal to the total change of the kinetic energy
Rotational Power
dWrot
Prot ≡ . (13.6.27)
dt
We can use our result for the infinitesimal work to find that the rotational power is the
product of the applied torque with the angular velocity of the rigid body,
dWrot dθ
Prot ≡ = (τ S ) z = (τ S ) z ω . (13.6.28)
dt dt
8/25/2008 27