02 Emi PDF
02 Emi PDF
GURU
JEE-Physics
ELECTROMAGNETIC INDUCTION
MAGNETIC FLUX
The magnetic flux () linked with a surface held in a magnetic field (B) is defined as the number of magnetic lines
of force crossing that area (A). If is the angle between the direction of the field and normal to the area, (area
vector) then B.A = BA cos
A B
FLUX LINKAGE
If a coil has more than one turn, then the flux through the whole coil is the sum of the fluxes through the
individual turns. If the magnetic field is uniform, the flux through one turn is = BA cos If the coil has N turns,
the total flux linkage = NBA cos
• Magnetic lines of force are imaginary, magnetic flux is a real scalar physical quantity with dimensions
F F
[ ] B area [L2 ] B I L sin [ F = B I L sin]
IL
M L T2 2 2 2 1
[ ] [L ] [M L T A ]
A L
max = B A
when magnetic field B is normal to the area
min = 0
= 90° cos = minimum = 0 min = 0
E 1
JEEMAIN.GURU
JEE-Physics
Example
A loop of area 0.06 m2 is placed in a magnetic field 1.2 T with its plane inclined 30° to the field direction. Find
the flux linked with plane of loop.
Solution
Area of loop is 0.06 m2 , B = 1.2 T and = 90° – 30° = 60° So, the flux linked with the loop is
1
= BA cos = 1.2 × 0.06 × cos = 1.2 × 0.06 × = 0.036 Wb
2
Example
A loop of wire is placed in a magnetic field B 0.3 ˆj T .
Find the flux through the loop if area vector is A (2 ˆi 5 ˆj 3 kˆ)m 2
Solution
Flux linked with the surface B A (0.3 ˆj) (2 ˆi 5 ˆj 3 kˆ)m = 1.5 Wb
2
Example
At a given plane, horizontal and vertical components of earth's magnetic field BH and BV are along x and y axes
respectively as shown in figure. What is the total flux of earth's magnetic field associated with an area S, if the
area S is in (a) x-y plane (b) y-z plane and (c) z-x plane ?
y y
y BV BV
BV
S
S S BH
x x
x BH
BH (b) (c)
z z
z (a)
Solution
B ˆi B H ˆj B V = constant, so B . S [ B = constant]
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
(a) For area in x-y plane S S kˆ , ˆ )0
xy (iˆB H ˆj B V ).( kS
(b) For area S in y-z plane S S ˆi , yz (iˆB H ˆj B V ).(ˆi S ) B H S
(c) For area S in z-x plane S S ˆj , zx (iˆB H ˆj B V ).(ˆj S) B V S
2
E
JEEMAIN.GURU
JEE-Physics
ELECTROMAGNETIC INDUCTION
Michael Faraday demonstrated the reverse effect of Oersted experiment. He explained the possibility of producing
emf across the ends of a conductor when the magnetic flux linked with the conductor changes. This was termed
as electromagnetic induction. The discovery of this phenomenon brought about a revolution in the field of
electric power generation.
v
• When the N-pole of a strong bar magnet is moved away from the coil, N S
deflection to
the left of
the galvanometer shows a deflection left to the zero mark. zero mark
v
• If the above experiments are repeated by bringing the S-pole of the,
S N
deflection to
magnet towards or away from the coil, the direction of current in the the left of
zero mark
C ON C LU S I ON S
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
Whenever there is a relative motion between the source of magnetic field (magnet) and the coil, an emf is
induced in the coil. When the magnet and coil move towards each other then the flux linked with the coil
increases and emf is induced. When the magnet and coil move away from each other the magnetic flux linked
with the coil decreases, again an emf is induced. This emf lasts so long the flux is changing.
Due to this emf an electric current start to flow and the galvanometer shows deflection.
The deflection in galvanometer last as long the relative motion between the magnet and coil continues.
Whenever relative motion between coil and magnet takes place an induced emf produced in coil. If coil is in
closed circuit then current and charge is also induced in the circuit. This phenomenon is called electro magnetic
induction.
E 3
JEEMAIN.GURU
JEE-Physics
FAR A DAY'S L AWS OF ELECTROM AGNETIC INDUCTION
Based on his experimental studies on the phenomenon of electromagnetic induction, Faraday proposed the
following two laws.
• First law
Whenever the amount of magnetic flux linked with a closed circuit changes, an emf is induced in the circuit. The
induced emf lasts so long as the change in magnetic flux continues.
• Second law
The magnitude of emf induced in a closed circuit is directly proportional to rate of change of magnetic flux
d
linked with the circuit. If the change in magnetic flux in a time dt is = d then e
dt
LENZ'S L AW
The Russian scientist H.F. Lenz in 1835 discovered a simple law giving the direction of the induced current
produced in a circuit. Lenz's law states that the induced current produced in a circuit always flow in such a
direction that it opposes the change or cause that produced it. If the coil has N number of turns and is the
magnetic flux linked with each turn of the coil then, the total magnetic flux linked with the coil at any time = N
d d N ( 2 1 )
e (N ) N
dt dt t
S N N S
ACW CW
v v
N S N S
rest rest
(Coil face behaves as North pole (Coil face behaves as South pole
to opposes the motion of magnet.) to opposes the motion of magnet.)
d
e ( ) , here negative sign indicates the concept of Lenz law.
dt
Copper coils are wound on a cylindrical cardboard and the two ends of the coil are
connected to a sensitive galvanometer. When a bar magnet is moved towards the coil
N
(fig.). The upper face of the coil near the magnet acquired north polarity.
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
Consequently work has to be done to move the magnet further agains the force of
repulsion. When we withdraw the magnet away from the coil, its nearer face acquires
G
south polarity. Now the workdone is against the force of attraction.When the magnet
is moved, the number of magnetic lines of force linking the coil changes, which
causes an induced current of flow through the coil. The direction of the induced
current, according to Lenz's law is always to oppose the motion of the magent.
The workdone in moving the magnet is converted into electrical energy. This energy
is dissipated as heat energy in the coil. Therefore, the induced current always flows in
such a direction to oppose the cause. Thus it is proved that Lenz's law is the
consequence of conservation of energy.
4
E
JEEMAIN.GURU
JEE-Physics
cut
I
open circuit also. ACW
induced current = 0
metal loop
but emf 0
• In all E.M.I. phenomenon, induced emf is non-zero induced parameter.
• Induced charge in any coil (or circuit) does not depends on time in which change in flux occurs i.e. it is
independent from rate of change of flux or relative speed of coil–magnet system.
• Induced charge depends on change in flux through the coil and nature of the coil (or circuit) i.e. resistance.
Example
The radius of a coil decreases steadily at the rate of 10–2 m/s. A constant and uniform magnetic field of induction
10 –3 Wb/m 2 acts perpendicular to the plane of the coil. What will be the radius of the coil when the induced
e.m.f. in the 1V
Solution
d (BA ) Bd ( r 2 ) dr e 1 10 6 5
Induced emf e =
dt
dt
= 2Br
dt
radius of coil r =
FG dr IJ 3
2 10 10 2
cm
2B
H dt K
Example
The ends of a search coil having 20 turns, area of cross-section 1 cm2 and resistance 2 ohms are connected to
a ballistic galvanometer of resistance 40 ohms. If the plane of search coil is inclined at 30° to the direction of a
magnetic field of intensity 1.5 Wb/m2, coil is quickly pulled out of the field to a region of zero magnetic field,
calculate the charge passed through the galvanometer.
Solution
The total flux linked with the coil having turns N and area A is
NBA
1 N (B . A ) = NBA cos = NBA cos(90° – 30°) = 2
NBA
when the coil is pulled out, the flux becomes zero, 2 = 0 so change in flux is =
2
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
NBA 20 1.5 10 4
the charge flowed through the circuit is q = = 0.357 10 4 C
R 2R 2 42
Example
Solution
L to N]
E 5
JEEMAIN.GURU
JEE-Physics
Example
The cross-sectional area of a closely-wound coil having 40 turns in 2.0 cm 2 and its resistance is
16 ohm. The ends of the coil are connected to a B.G. of resistance 24 ohm. Calcualte the charge flowing
through the B.G. when the coil is pulled quickly out of a region where field is
2.5 Wb/m2 to a region of zero magnetic field.
Solution
N = 40, B = 2.5 Wb/m2 , A = 2.0 cm × 10–4 m2 and R = 16 + 24 = 40 ohms
Example
A current i = 3.36(1 + 2t) × 10–2 A increases at a steady rate in a long straight wire. A small circular loop of
radius 10–3 m has its plane parallel to the wire and its centre is placed at a distance of 1m from the wire. The
resistance of the loop is 8.4 × 10–4 . Find the magnitude and the direction of the induced current in the loop.
Solution
1m
0 I 2 10 7 I
The field due to the wire at the centre of loop is B I
2 d 1
d dI
So emf induced in the loop due to change of current | e| 2 10 13
dt dt
dI
I = 3.36 (1 + 2t) × 10–2 6.72 10 2 A/s
dt
e 13.44 10 15
And the induced current in the loop i 16 10 12 A
R 8.4 10 4
Due to increase in current in the wire the flux linked with the loop will increase, so in accordance with Lenz's law
the direction of current induced in the loop will be inverse of that in wire, i.e., anticlockwise.
Example
A 10 ohm resistance coil has 1000 turns. It is placed in magnetic field of induction 5 × 10–4 tesla for 0.1 sec. If
the area of cross-section is 1m2, then calculate the induced emf.
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
Solution
d NBA 1000 5 10 4 1
Magnetic flux through the coil = NBA Induced emf = = 5V
dt t 0.1
Example
A coil of mean area 500 cm2 and having 1000 turns is held perpendicular to a uniform field of 0.4 gauss. the
coil is turned through 180° in 1/10 second. Calculate the average induced emf.
6
E
JEEMAIN.GURU
JEE-Physics
Solution
When the plane of coil is perpendicular to field, the angle between area A and field B is 0°.
The flux linked with coil 1 = NBA cos 0 = NBA. When coil is turned through 180°, the flux linked 2 = NBA cos
Example
Shown in the figure is a circular loop of radius r and resistance R. A
variable magnetic field of induction B = B0 e–t is established inside the x x x R
x x xx x
coil. If the key (K) is closed. Then calculate the electrical power developed x x x x
xx
right after closing the key. x r x
x x K
Solution
d d dB d
Induced emf e (BA ) A r 2 B 0 (e t ) r 2 B 0 e t
dt dt dt dt
At t = 0, e0 = B0 e–0 . r2 = B0 r 2
e 20 B 20 2 r 4
The electric power developed in the resistor R just at the instant of closing the key is P
R R
Example
Two concentric coplanar circular loops made of wire, resistance per unit length 10 –4 m –1, have diameters
0.2 m and 2 m. A time-varying potential difference (4 + 2.5 t) volt is applied to the larger loop. Calculate the
current in the smaller loop.
Solution
0 I V=4+2.5t S
r
The magnetic field at the centre O due to the current in the larger loop is B R
2R
r << R, so the field B can be taken almost constant over the entire area of the smaller loop.
0 . 4 2.5 t . 2 d r2
the flux linked with the smaller loop is B r 2 r Induced emf e = 0 2 2.5
2 R 2 R dt 4 R
E 7
JEEMAIN.GURU
JEE-Physics
Example
(a) A current from A to B is increasing in magnitude then what is the direction of induced current in the loop
and
(b) if current is decreasing in magnitude then what is the direction of current in the loop.
(c) If instead of current if an electron is moving in the same direction, what will happen ?
Solution
(a) When current in the wire AB increases, the flux linked with the I=increasing
f=increasing Bout CW
loop (which is out of the page) will increase, and hence the induced Ii = inverse
Ii
current in the loop will be inverse, i.e., clockwise and will try to
decrease the flux linked with it, i.e., will repel the conductor AB I
as shown in figure. A C B
(b) When current in the wire AB decreases, the flux linked with I=decreasing ACW
f=decreasing B out
the loop (which is out of the page) will decrease, and hence the I = direct
i
I
i
induced current in the loop will be in anticlockwise direction and
will try to increase the flux linked with it, i.e., will attract the I
conductor AB as shown in figure. A C B
(c) If an electron moving from left to right, the flux with the loop (which is into the page) will first increase and
then decrease as the electron passes by. So the induced current Ii in the loop will be first anticlockwise
and will change direction (i.e., will become clockwise) as the electron passes by.
Example
A magnet is moved in the direction indicated by an arrow between
two coils AB and CD as shown in the figure. Suggest the direction of
induced current in each coil.
Solution
For coil AB : Looking from the end A, the current in the coil AB will be in anticlokwise direction.
For coil CD : Looking from the end D, direction of current in the coil CD will be anticlockwise.
Note : as the N-pole of the magnet is moving away from the coil AB, the end B of the coil will behave as S-pole
so as to oppose the motion of the magnet and the end C of the coil CD should behave as S-pole so as to repel
the approaching magnet.
Example
In a region of gravity free space, there exists a non-uniform magnetic field B B 0 x 3 kˆ . A uniform conductor
AB of length L and mass m is placed with its end A at origin such that it extends along +x-axis. Find the initial
acceleration of the centre of mass and that of end A when a current i flows from A to B.
Solution
Consider a small sectionof length dx at a ditance x from left end (or end A).
3
B=-B0x k
The force on this section is dF i dxiˆ B 0 x kˆ = B 0 ix 3 dxjˆ
3 x dx
A B
Force on entire rod is given by, x=0 i y
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
L B 0 iL4 ˆ Fm B iL4
3 ˆ
Fm dF B 0 ix dxj j a cm 0 ˆj
0 4 mass 4m x
To find acceleration of a point on the rod, we first find angular acceleration of the rod about centre of mass. The
torque due to dF about centre of mass on the rod is
L L
d x i dF r F d x B 0 ix 3 dxkˆ
2 2
L 4 3 L L L5 3B 0 iL5 ˆ
Net torque on the rod is 0 B 0 ikˆ x x dx B 0 ikˆ k
2 5 8 40
8
E
JEEMAIN.GURU
JEE-Physics
dF
CM
3B 0 iL5 ˆ 9 B 0 iL3 ˆ
k k A C B
mL2 10 m x dx
As , 40 x=0 x=L
12 L/2
Now, acceleration of end A is a A a cm rAC , where rAC is position vector of A with respect to centre of
zero. When a charge q goes once around the loop, the total work done on it by the
electric field is equal to q times the emf.
d
Hence E . d e dt
...(i)
This equation is valid only if the path around which we integrate is stationary.
(ii) Due to of symmetry, the electric field E has the same magnitude at every point on the circle and it is tangential
at each point (figure).
(iii) Being nonconservative field, so the concept of potential has no meaning for such a field.
(iv) This field is different from the conservative electrostatic field produced by stationary charges.
(v) The relation F q E is still valid for this field. (vi) This field can vary with time.
d dB
• For symmetrical situations E A
dt dt
Direction of induced electric field is the same as the direction of included current.
Example
The magnetic field at all points within the cylindrical region whose cross-section is x x x
x x x x
tesla x x x x
indicated in the figure start increasing at a constant rate . Find the
sec ond
x R x x
magnitude of electric field as a function of r, the distance from the geomatric x x x
E 9
JEEMAIN.GURU
JEE-Physics
Solution
For r < R : x x x
x
dB
x
E A
dt x
r x
R
r x x
E (2r) = (r2) E E r x x x
2
x x x
R x
At r = R, E
2 x R
r x x
For r > R :
E
dB
E A
dt R
2
E1
R 2 1 E r r
2
E (2r) = (R ) E E
2r r
Example R
For the situation described in figure the magnetic field changes with time according to
B = (2.00 t3 – 4.00 t2 + 0.8) T and r2 = 2R = 5.0 cm
(a) Calculate the force on an electron located at P2 at t = 2.00 s
x x x
(b) What are the magnetude and direction of the electric field at x x
r1 P1
P1 when t = 3.00 s and r1 = 0.02m. x x r2
x P2
x
Solution x x x
R
x x x
2 2
Bin
dB R d R
E A E (2t 3 4 t 2 0.8) (6 t 2 8 t)
dt 2 r2 dt 2r2
19 2 2
at t = 2 s F 1.6 10 (2.5 10 ) [6(2)2 8(2)] I
2 5 10 2 E
x x x
x x r1
x x r2
x x
1.6 x x x
2.5 10 21 (24 16) 8 10 21 N at t = 2s, x x x
4
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
F = -e E
dB
is positive so it is increasing.
dt
direction of induced current and E are as shown in figure and hence force of electron having charge
–e is right perpendicular to r2 downwards
r12 dB
(b) For r1 = 0.02 m and at t = 3s, E (6 t 2 8 t) 0.02 [6(3)2 8(3)] = 0.3 V/m at t = 3sec,
2 r1 2 dt
is positive so B is increasing and hence direction of E is same as in case (a) and it is left perpendicular to
r 1 upwards.
10
E
JEEMAIN.GURU
JEE-Physics
NO E.M.I. CASES
Condition of No EMI If :
vertical wire
No flux linkage through the coil =0 horizontal =0
field lines
or Flux linkage through the coil = constant
v v
v
v
N S
•
no relative motion no relative motion
(=constant) (=constant)
N S
no relative motion no relative motion
(=constant) (=constant)
B uniform
• Any rectangular coil or loop translates within the uniform
b rectangular loop
V
uniform transverse magnetic field its flux remains const.
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
(=constant)
• No flux associated for the coils or loops which are placed in mutually
vertical
I
perpendicular planes. Hence If current of one either increase or
horizontal
decrease, there is no effect on flux of other.
E 11
JEEMAIN.GURU
JEE-Physics
METHODS OF PRODUCING INDUCED EMF (TYPES OF EMI)
Emf can be induced in a closed loop by changing the magnetic flux linked with a circuit.
The magnetic flux is = BA cos Magnetic flux can be changed by one of the following methods :
(i) Changing the magnetic field B. (Static emi)
(ii) Changing the area A of the coil and (dynamic emi)
(iii) Changing the relative orientation of B and A (Periodic emi)
Change in the magnetic flux linked with the loop in the dt is d = B × A = B × dx
dx
induced emf e = d B dx = B v v
dt dt dt
e Bv
If the resistance of circuit is R and the circuit is closed then the current through the circuit I I
R R
A magnetic force acts on the conductor in opposite direction of velocity is
x x x a x x
B 2 2 v .
Fm i B Fapplied
R x x x x
Fm v
So, to move the conductor with a constant velocity v an equal and opposite
B 2 2 v x x x b x x
force F has to be applied in the conductor. F Fm
R
B 2 2 v 2
The rate at which work is done by the applied force is, Papplied Fv
R
2
Bv B 2 2 v 2
and the rate at which energy is dissipated in the circuit is, Pdissipated i 2 R R
R R
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
This is just equal to the rate at which work is done by the applied force.
the battery. x x x b x x
e Bv
Hence, the current in the ciruit is i
R r R r
12
E
JEEMAIN.GURU
JEE-Physics
Example
Twelve wires of equal lengths are connected in the form of a skeleton cube which
is moving with a velocity v in the directon of magnetic field B . Find the e.m.f.
in each arm of cube.
Solution
FG e IJ
No e.m.f. is induced in any arm becuase v is parallel to B
H d
.( B v )
K
Example
Wire PQ with negligible resistance slides on the three rails with
5 cm/sec. Calculate current in 10 resistance when switch
S is connected to (a)position 1 (b)position 2
Solution
e Bv 1 5 10 2 2 10 2
(a) For position 1 Induced current I = = = = 0.1 mA
R R 10
e Bv (2) 1 5 10 2 4 10 2
(b) For position 2 Induced current I = = = = 0.2 mA
R R 10
Example
A copper wire of length 2m placed perpendicular to the plane of magnetic field B (2 i 4 j ) T . If it moves
i j k
Dynamic emf e d = . ( v B ) = . (B v ) (B v ) = 2 4 0 = i (32 – 0) – j (16 – 0) + k (12 – 16)
4 6 8
The rod ab will act as a source of emf e1 = Bv = (0.01) (4.0) (0.1) = 4 × 10–3 V
and internal resistance r1 = 10.0
Similarly, rod ef will also act as source of emf e2 = (0.01) (2.0) (0.1) = 2 × 10–3 V
and internal resistance r2 = 15.0
a c e
From right hand rule :Vb > Va and Ve > Vf Also R = 5.0 , e 2
e r e 2 r1 r1
E eq 1 2 6 10 3 20 10 3 40 R r2
10 3 1.6 10 3 volt
r1 r2 15 10 25 e1
b d f
15 10 E eq 1.6 10 3 1.6 8
req = 6 and I = 10 3 10 3 amp from d to c
15 10 req R 6 6 11 55
E 13
JEEMAIN.GURU
JEE-Physics
MOTIONAL EMF FROM LORENTZ FORCE
A conductor PQ is placed in a uniform magnetic field B, directed normal to
B
the plane of paper outwards. PQ is moved with a velocity v, the free electrons B –Q
of PQ also move with the same velocity. The electrons experience a magnetic – ––
) –
e
Lorentz force, Fm (v B) . According to Fleming's left hand rule, this force
v ×B
(
acts in the direction PQ and hence the free electrons will move towards Q. A – e e–
negative chagre accumulates at Q and a positive charge at P. An electric field + v
++
E is setup in the conductor from P to Q. Force exerted by electric field on the P+
free electrons is, Fe eE
The accumulation of charge at the two ends continues till these two forces balance each other.
so Fm Fe e(v B ) = – eE E (v B )
The potential difference between the ends P and Q is V = E. = (v B ). .It is the magnetic force on the moving
free electrons that maintains the potential difference and produces the emf = B v (for B v )
As this emf is produced due to the motion of a conductor, so it is called a motional emf.
The concept of motional emf for a conductor can be generalized for any shape moving in any magnetic field
uniform or not. For an element d of conductor the contribution de to the emf is the magnitude d multiplied by
the component of v B parallel to d , that is de ( v B). d
For any two points a and b the motional emf in the direction from b to a is,
x x x x b x x x x x b
c c
v v a
x x x x x x x x e ( v B). d
a a v= v cos b
x x x x x x x x x x x
Motional emf in wire acb in a uniform magnetic field is the motional emf in an imaginary wire ab. Thus, eacb = eab
= (length of ab) (v) (B), v = the component of velocity perpendicular to both B and ab. From right hand rule
: b is at higher potential and a at lower potential. Hence, Vba = Vb – Va = (ab) (v cos) (B)
Direction of induced current or HP end of the rod find out with the help of
Fleming right hand rule
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
14
E
JEEMAIN.GURU
JEE-Physics
Example
An aircraft with a wing span of 40 m flies with a speed of 1080 kmh–1 in the eastward direction at a constant
altitude in the northern hemisphere, where the vertical component of earth's magnetic field is 1.75 × 10–5 T.
Find the emf that develops between the tips of the wings.
Solution
The metallic part between the wing-tips can be treated as a single conductor
cutting flux-lines due to vertical component of earth's magnetic field. So emf
is induced between the tips of its wings. v
1 1080 1000
Here l = 40 m, BV = 1.75 × 10–5 T, v 1080 kmh ms 1 = 300 ms–1
3600
BV
= BV v = 1.75 × 10–5 × 40 × 300 = 0.21 V
Example
A rod PQ of length L moves with a uniform velocity v parallel to a long straight wire carrying a current i, the end
P remaining at a distance r from the wire. Calculate the emf induced across the rod. Take v = 5.0 m/s, i = 100 amp,
r = 1.0 cm and L = 19 cm.
Solution
The rod PQ is moving in the magnetic field produced by the current-carrying
i dx v
long wire. The field is not uniform throughout the length of the rod (changing P Q
with distance). Let us consider a small element of length dx at distance x
from wire. if magnetic field at the position of dx is B then emf induced x
0 i
d= B v dx v dx
2 x
Q 0 i
emf is induced in the entire length of the rod PQ is d v dx
P 2 x
Now x = r at P, and x = r + L at Q. hence
0 i v r L dx 0 i v r L iv iv r L
log e x r 0 [log e (r L ) log e r] 0 log
2 r x 2 2 2 r
1.0 19
Putting the given values : = (2 × 10–7) (100) (5.0) loge = 10–4 loge 20 Wb/s = 3 × 10–4 volt
1.0
Example
A horizontal magnetic field B is produced across a narrow gap between square x x x x x x
iron pole-pieces as shown. A closed square wire loop of side , mass m and x x x x x x
resistance R is allowed of fall with the top of the loop in the field. Show that the x x x x x x
x x x x x x
Rmg x x x x x x
loop attains a terminal velocity given by v while it is between the poles of
B 2 2 x x x x x x
the magnet.
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
Solution
mg
As the loop falls under gravity, the flux passing through it decreases and so an
induced emf is set up in it. Then a force F which opposes its fall. When this force
becomes equal to the gravity force mg, the loop attains a terminal velocity v.
e Bv x x x x x x
The induced emf e = B v , and the induced current is i
R R x x x x x x
x x x x x x
B 2 v 2 x x x F x x
The force experienced by the loop due to this current is F B i x x x x x x
R
x x x x x x
B 2 v 2 R mg
When v is the terminal (constant) velocity F = mg or mg or v 2 2
R B
mg
E 15
JEEMAIN.GURU
JEE-Physics
Example
Figure shows a rectangular conducting loop of resistance R, width L, and d
(i) Plot the flux through the loop as a function of the position x of the
right side of the loop.
(ii) Plot the induced emf as a function of the positioin of the loop.
(iii) Plot the rate of production of thermal energy in the loop as a function of the position of the loop.
Solution
(i) When the loop is not in the field : coil out coil entering coil in coil leaving coil out
8
The flux linked with the loop = 0
When the loop is entirely in the field : (mWb)
4
Magnitic flux linked with the loop
= B L b = 2 × 40 × 10–3 × 10–1 = 8 mWb x(in cm)
0
When the loop is entering the field : 0 5 10 15 20 25 30
fig. (i)
The flux linked with the loop = B L x
When the loop is leaving the field :
The flux = B L [b – (x – d)]
d d dx d
(ii) Induced emf is e v
dt dx dt dx coil out coil entering coil in coil leaving coil out
80
= – slope of the curve of figure (i) × v
The emf for 0 to 10 cm : 40
(8 0) 10 3 0
e = – 1 80 mV x(in cm)
(10 0) 10 2 (mV)
–40
The emf for 10 to 15 cm : e = 0 × 1 = 0
The emf for 15 to 25 cm : –80
0 5 10 15 20 25 30
(0 8) 10 3 fig. (ii)
e = – 1 80 mV
(25 15) 10 2
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
e2
(iii) The rate of thermal energy production is P coil out coil entering coil in coil leaving coil out
R
P(mW)
(80 10 3 ) 2
for 0 to 10 cm : P = 4 mW 4
1.6
0
for 10 to 15 cm : P = 0
0 5 10 15 20 25 30
fig. (iii)
(80 10 3 ) 2
for 15 to 25 cm : P = 4 mW
1.6
16
E
JEEMAIN.GURU
JEE-Physics
Example
Two long parallel wires of zero resistance are connected to each other by a battery of 1.0 V. The separation
between the wires is 0.5 m. A metallic bar, which is perpendicular to the wires and of resistance 10 , moves on
these wires. When a magneticfield of 0.02 testa is acting perpendicular to the plane containing the bar and the
wires. Find the steady-state veclocity of the bar. If the mass of the bar is 0.002 kg then find its velocity as a
function of time.
Solution
B=0.02T
1.0 V x x x x x x
The current in the 10 bar is I 0.1 A
10 x x x x x x
1.0V I F
x x x x x 0.5m
The current carrying bar is placed in the magnetic field B (0.2 T) x x x x x x
x x x x x x
perpendicular to the plane of paper and directed downwards.
The magnetic force of the bar is F = B I = 0.02 × 0.5 × 0.1 0 = 1 × 10–3 N
The moving bar cuts the lines of force of B . If v be the instantaneous velocity of the bar, then the emf induced
in the bar is = Bv = 0.02 × 0.5 × v = 0.01 v volt. By Lenz's law, will oppose the motion of the bar which
will ultimately attain a steady velocity. In this state, the induced emf will be equal to the applied emf (1.0 volt).
1.0
0.01 v = 1.0 or v 100 ms–1
0.01
Again, a magnetic force F acts on the bar. If m be the mass of the bar, the acceleration of the rod is
dv F F F F
dv .dt Integrating, dv m dt v t C (constant)
dt m m m
F 3
If at t = 0, v = 0 then C = 0. v t But F = 1 × 10–3 N, m = 0.002 kg v 1 10 t = 0.5 t
m 0.002
Example
In figure, a rod closing the circuit moves along a U-shaped wire at a
constant speed v under the action of the force F. The circuit is in a
uniform magnetic field perpendicualr to its plane. Calculate F if the x x x x x
rate generation of heat is P. B x x x x x
F
Solution x x x x x
x x x x x
The emf induced across the ends of the rod, = Bv
B v
Current in the circuit, I Magnetic force on the conductor, F' = IB, towards leftt
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
R R
F F P
acceleration is zero F' = F BI = F or I P = I = B v× = Fv F
B B v
Example
x x x a x x
The diagram shows a wire ab of length and resistance R sliding on a smooth
pair of rails with a velocity v towards right. A uniform magnetic field of induction +
S x x v x
B acts normal to the plane containing the rails and the wire inwards. S is a –
current source providing a constant I in the circuit.
x x x b x x
Determine the potential difference between a and b.
E 17
JEEMAIN.GURU
JEE-Physics
Solution
The wire ab which is moving with a velocity v is equivalent to an emf
source of value B v with its positive terminal towards a.
Potential difference Va – Vb = Bv – IR
Example
N B
A thin semicircular conduting ring of radius R is falling with its plane vertical
v
in a horizontal magnetic induction B (fig.). At the position MNQ, the speed of
the ring is v. What is the potential difference developed across the ring at the M Q
position MNQ ?
Solution
Let semiconductor ring falls through an infinitesimally small distance dx from
its initial position MNQ to M'Q'N' in time dt (fig).
N B
decrease in area of the ring inside the magnetic field, N'
dA = – MQQ'M' = – M'Q' × QQ' = –2R dx
v
change in magnetic flux linked with the ring, M Q
dx
d = B × dA = B × (–R dx) = – 2BR dx M' Q'
2R
d dx
The potential difference developed across the ring, e 2 B R 2 B R v
dt dt
dx
the speed with which the ring is falling v
dt
x2
So, net induced e.m.f. across conducting rod d B x dx B
0 2 0
1 1
or B 2 B 2 f 2 [f = frequency of rotation]
2 2
18
E
JEEMAIN.GURU
JEE-Physics
Example
A wheel with 10 metallic spokes each 0.5 m long is rotated with angular speed of 120 revolutions per minute
in a plane normal to the earth's mangetic field. If the earth's magnetic field at the given place is 0.4 gauss, find
the e.m.f. induced between the axle and the rim of the wheel.
Solution
120
= 2n = 2 4 , B = 0.4 G = 4 × 10–5 T, length of each spoke = 0.5 m
60
1 1 2
induced emf e B 2 4 10 5 4 0.5 6.28 10 5 volt
2 2
As all the ten spokes are connected with their one end at the axle and the other end at the rim, so they are
connected in parallel and hence emf across each spoke is same. The number of spokes is immaterial.
Example
A horizontal copper disc of diameter 20 cm, makes 10 revolutions/sec about a vertical axis passing through its
centre. A uniform magnetic field of 100 gauss acts perpendicular to the plane of the disc. Calculate the
potential difference its centre and rim in volts.
Solution
B = 100 gauss = 100 × 10–4 Wb/m2 = 10–2, r = 10 cm = 0.10 m, frequency of rotaion = 10 rot/sec
A
1 1
The emf induced between centre and rim B 2 B r 2 ( r = )
2 2
1
= 2f = 2 × 3.14 × 10 = 62.8 s–1 10 62.8 (0.1) 2 = 3.14 × 10–3 V = 3.14 mV..
2
Example
A circular copper disc 10 cm in radius rotates at 20 rad s–1 about an axis through its centre and perpendicular
to the disc. A uniform magnetic field of 0.2 T acts perpendicular to the disc. (a) Calculate the potential difference
developed between the axis of the disc and the rim. (b) What is the induced current, if the resistance of 2 is
connected in between axis and rim of the disc.
Solution
Here B = 0.2 T radius of the circular disc, r = 10 cm = 0.1 m resistance of the disc, R = 2
angular speed of rotation of the disc, = 20 rad s–1
(a) If e is the induced e.m.f. produced between the axis of the disc and its rim, then
1 1
B r 2 0.2 20 (0.1) 2 = 0.0628 V
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
e =
2 2
E 19
JEEMAIN.GURU
JEE-Physics
Wb N.m J
S I unit of L : 1 =1 Henry = 1 2 = 1 2 Dimensions : [M 1 L 2T -2 A –2 ]
amp A A
Note : L is constant of coil it does not depends on current flow through the coil.
Case - II Current through the coil changes w.r.t. time
dI dB d
If
dt
dt dt Static EMI N = LI
d dI d
–N =–L , (– N ) called total self induced emf of coil 'eS'
dt dt dt
dI V. s
es L S.I. unit of L
dt A
SELF-INDUCTANCE OF A SOLENOID
Let cross-sectional area of solenoid=A, Current flowing through it=
µ0 N µ N2 A
Length of the solenoid =, then NBA N A 0
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
µ0 N 2 A 0 r N 2 A
But LI L or L m=
If no iron or similar material is nearby, then the value of self-inductance depends only on the geometrical
factors (length, cross-sectional area, number of turns).
Example
The current in a solenoid of 240 turns, having a length of 12 cm and a radius of 2 cm, changes at the rate of 0.8
As–1. Find the emf induced in it.
Solution
dI 0 N 2 A . dI 4 10 7 (240) 2 (0.02) 2
| | L 0.8 6 10 4 V
dt dt 0.12
20
E
JEEMAIN.GURU
JEE-Physics
MUTUAL INDUCTION (N1,1B1,L1) (N2,2B2,L2)
air gap
Whenever the current passing through primary coil
I A1 A2
or circuit change then magnetic flux neighbouring M I
primary (S.I.) secondary (M.I.)
secondary coil or circuit will also change. Acc. to + – G
( )
E Rh
Lenz for opposition of flux change, so an emf (1) (2)
This phenomenon called as 'Mutual induction'. In case of mutual inductance for two coils situated close to each
other, flux linked with the secondary due to current in primary.
N 2 2 N 2 B 1 A 2 ( T ) s
N2 2 I1 N2 2 = MI1, M where M : is coefficient of mutual induction.
I1 I1 Ip
dI1 dB 1 d 1 d 2
If Static EMI
dt dt dt dt
d 2 dI1 d
N 2 2 = MI 1 –N2 = –M , N 2
dt dt dt
N 2B1 A N 0 N 1 I1 N N A
Ms s 0 1 2
M s1s2 = = 2 A
I1
1 2
(N1) S I1
E 21
JEEMAIN.GURU
JEE-Physics
N1 N 2 B1 A 2
M c1c2 = where B1 = 0 N 1 I1 , A2 = r22
r1 I1 2r1
N2 r2 O
(r1>>r2) I 2N 0 1 1
N I 0 N 1 N 2 r22
M c1c2 = I 2r (r22) M c c 1 2
2r1
1 1
Two concentric loop : Two concentric square loops : A square and a circular loop
tiny tiny
r2 r2 O b2 a r2
M 2 (r >> r ) M M r
r1 1 2 r1
a b a
a
M K L 1 L 2 here 'K' is coupling factor between two coils and its range 0 K 1
1 1 1 L 1L 2 1 1 1
(a) If M = 0 then L
L L 1 L 2 or L1 L2 (b) If M 0 then L (L 1 M ) (L 2 M )
22
E
JEEMAIN.GURU
JEE-Physics
Example
On a cylindrical rod two coils are wound one above the other. What is the coefficient of mutual induction if the
inductance of each coil is 0.1 H ?
Solution
One coil is wound over the other and coupling is tight,so K = 1, M L 1 L 2 0.1 0.1 0.1H
Example
How does the mutual inductance of a pair of coils change when :
(i) the distance between the coils is increased ?
(ii) the number of turns in each coil is decreased ?
(iii) a thin iron rod is placed between the two coils, other factors remaining the same ?
Justify your answer in each case .
Solution
(i) The mutual inductance of two coils, decreases when the distance between them is increased. This is
because the flux passing from one coil to another decreases.
0 N 1 N 2 A
(ii) Mutual inductance M i.e., M N1 N2 Clearly, when the number of turns N1 and N2 in the
two coils is decreased, the mutual inductance decreases.
(iii) When an iron rod is placed between th two coils the mutual inductance increases, because
M permeability ()
Example
A coil is wound on an iron core and looped back on itself so that the core has two sets of closely would wires in
series carrying current in the opposite sense. What do you expect about its self-inductance ? Will it be larger or
small ?
Solution
As the two sets of wire carry currents in opposite directions, their induced emf's also act in opposite directions.
These induced emf's tend to cancel each other, making the self-inductance of the coil very small.
This situation is similar to two coils connected in series and producing fluxes in opposite directions. Therefore,
their equivalent inductance must be Leq = L + L – 2M = L + L – 2L = 0
Example
A solenoid has 2000 turns wound over a length of 0.3 m. The area of cross-section is
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
1.2 × 10–3 m2. Around its central section a coil of 300 turns is closely would. If an initial current of 2A is reversed
in 0.25 s, find the emf induced in the coil.
Solution
dI 2 2
M 3 10 3 48 10 3 V = 48 mV
dt 0.25
E 23
JEEMAIN.GURU
JEE-Physics
ENERGY STORED IN INDUCTOR
The energy of a capacitor is stored in the electric field between its plates. Similary, an inductor has the capability
of storing energy in its magnetic field.An increasing current in an inductor causes an emf between its terminals.
dW di di
Power P = The work done per unit time ei L i L i
dt dt dt
dW dU dU di
From dW = – dU (energy stored) so Li dU = Li di
dt dt dt dt
The total energy U supplied while the current increases from zero to final value i is,
I
1 2 I
U L idi L (i ) 0 U 1 L I 2
0 2 2
1 2
the energy stored in the magnetic field of an inductor when a current I is LI .
2
The source of this energy is the external source of emf that supplies the current.
di
• After the current has reached its final steady state value I, 0 and no more energy is input to the inductor..
dt
• When the current decreases from i to zero, the inductor acts as a source that supplies a total amount of energy
1 2
Li to the external circuit. If we interrupt the circuit suddenly by opening a switch the current decreases very
2
rapidly, the induced emf is very large and the energy may be dissipated in an arc the switch.
1 2 1
U L I (0 n 2 V ) I 2 (L = 0 n2 V) (V = Volume = A)
2 2
U 1 ( n I) 2 B2 1 B2
The energy per unit volume u 0 n 2 I 2 0 (B = 0 n I) u
V 2 2 0 2 0 2 0
Example
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
24
E
JEEMAIN.GURU
JEE-Physics
PERIODIC EMI
Let a coil intially placed perpendicular to uniform magnetic field. Now this coil starts
rotation about an axis that the flux linked with the coil change due to change in B
oriantation of area vector A with respect to magnetic field B A
Angle in between area vector A and magnetic field B is then
Example
A coil of 160 turns of cross-sectional area 250 cm2 rotates at an angular velocity of 300 radian/sec about an
axis parallel to the plane of the coil in a uniform magnetic field of 0.6 Wb/m2. What is the maximum emf
induced in the coil ? If the coil is connected to a resistance of 2 ohm, what is the maximum torque that has to
be delivered to maintain its motion.
Solution
The instantaneous induced emf is = NBA sin t NBA
max 720
The maximum current through the coil is i max = 360 amp.
R 2
The torque on a current-carrying coil placed in a magnetic field is = BINAsin = BINA sint
maximum torque = B I N A = 0.6 × 360 × 160 × (250 × 10–4) = 864 newton meter.
By Lenz's law, this torque opposes the rotaion of the coil. Hence to maintain the rotation an equal torque must
be inserted in the opposite direction. Therefore the required torque is 864 N-m.
Example
A very small circular loop of area 5 × 10–4 m2, resistance 2 ohm and negligible inductance is initially coplanar
and concentric with a much larger fixed circular loop of radius 0.1 m. A constant current of 1 ampere is passed
in the bigger loop and the smaller loop is rotated with angular velocity rad/s about a diameter. Calculate (a)
the flux linked with the smaller loop (b) induced emf and induced current in the smaller loop as a function of
time.
Solution
0 I 2 10 7
(a) The field at the centre of larger loop B 1 = 2 × 10–6 Wb/m2
2R 0.1
is initially along the normal to the area of smaller loop. Now as the smaller loop (and hence normal to its
plane) is rotating at angular velocity , with respect to B so the flux linked with the smaller loop at time
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
e2 1
(c) The induced current in the smaller loop is, I 2 10 9 sin t ampere
R 2
E 25
JEEMAIN.GURU
JEE-Physics
TRANSFORMER
Laminated
Worki ng pri nciple Core
Primary
Load
Mutual induction winding
• It can't work with D.C. supply, and if a battery is connected to its primary, then output is across scondary
is always zero ie. No working of transformer.
power to be transmission
IL = power losses = I 2L R L
line voltage
High voltage coil having more number of turns and always made of thin wire and high current coil having
less number of turns and always made of thick wires. Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
d s d p
(a) No flux leakage s = p =
dt dt
Es Ns
Ep = Np = n or p where n : turn ratio , p : transformation ratio
26
E
JEEMAIN.GURU
JEE-Physics
(b) No load condition
VS N S VS N S
VP = EP and ES = V S from (i) and (ii) V N = n or p
VP N P P P
VS I P
Pout = Pin and V SI S = V PI P valid only for ideal transformer
VP I S
VS I P N S
from equation (iii) and (iv) n or p
VP I S N P
Note : Generally transformers deals in ideal condition i.e. Pin = Pout, if other information are not given.
Pout V I
hence Pout < Pin always. efficiency of transformer S . S 100
Pin VP I P
Applications :
The most important application of a transformer is in long distance transmission of electric power from generating
station to consumers hundreds of kilometers away through transmission lines at reduced loss of power.
Transmission lines having resistance R and carrying current have loss of power = 2R.
This loss is reduced by reducing the current by stepping up the voltage at generating station. This high voltage
is transmitted through high-tension transmission lines supported on robust pylons (iron girder pillars). The
voltage is stepped down at consumption station. A typical arrangement is shown below :
Raja Park
Sub-Station
House
200 V to Step up Step down Step down
Kota thermal transformer transformer transformer
11 kV
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
Example
A small town with a demand of 800 kW of electric power at 220 V is situated 15 km away from an electric
power plant generating power at 440 V. The resistance of the two wire line carrying power is 0.5 per km.
The town gets from the line through a 4000 – 220 V step down transformer at a sub-station in the town.
(b) Estimate the line power loss in the form of heat.
(b) How much power must be plant supply, assuming there is a negligible power loss due to leakage?
(c) Characterise the step up transformer at the plant.
E 27
JEEMAIN.GURU
JEE-Physics
Solution
The diagram shows the network :
For sub-station, P = 800 kW = 800 × 103 watts
V = 220 V
P 800 10 3 40
S = = = × 103 A.
V 220 11
Primary current (p) in sub-station transformer will be given by
220 40 10 3
4000 × P = 220 × S, P = = 200 A
11 4000
(a) Hence transmission line current = 200 A
transmission line resistance = 2 × 15 × 0.5 = 15
transmission line power loss = 2R = 200 × 200 × 15 = 6 × 105 watt = 600 kW.
(b) power to be supplied by plant = power required at substation + loss of power of transmission
= 800 + 600 = 1400 kW.
ES NS E 230
Ep = 2300 V ; NP = 4000, ES = 230 V N S N P S 4000 400
EP NP EP 2300
Example
The output voltage of an ideal transformer, connected to a 240 V a.c. mains is 24 V. When this transformer is
used to light a bulb with rating 24V, 24W calculate the current in the primary coil of the circuit.
Solution
E S IS 24
EP = 240 V, ES = 24 V, ES IS = 24 W Current in primary coil IP = 0.1A
EP 240
LOSSES OF TRANSFORMER
(a) Copper or joule heating losses
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
28
E
JEEMAIN.GURU
JEE-Physics
(c) Iron losses
Where : There losses occurs in core part.
Types : (i) Hysteresis losses (ii) Eddy currents losses
(i) Hysteresis losses
Cause : Transformer core always present i n the effect of alternat i ng magnet ic field
(B = B0sint) so it will magnetised & demagnetised with very high frequeny (f = 50
Hz).During its demagnetization a part of magnetic energy left inside core part in form
of residual magnetic field. Finally this residual energy waste as heat.
Remmady : To minimise these losses material of transformer core should be such that it can be
easily magnetised & demagnetised. For this purpose soft ferromagnetic material
should be used. For example soft iron (low retentivity and low coercivity)
(F1<<<F 2)
• Eddy currents are basically the induced currents set up inside the body of conductor whenever the magnetic flux
linked with it changes.
• Eddy currents tend to follow the path of least resistance inside a conductor. So they from irregularly shaped
loops. However, their directions are not random, but guided by Lenz's law.
• Eddy currents have both undesirable effects and practically useful applications.
Applications of eddy currents :
(i) Induction furnace (ii) Electromagnetic damping
(iii) Electric brakes (iv) Speedometers
(v) Induction motor (vi) Electromagnetic shielding
(vii) Inductothermy (viii) Energy meters
• Circulation plane of these currents is always perpendicular to the external field direction.
• Generally resistance of metal bodies is low so magnitude of these currents is very high.
• These currents heat up the metal body and some time body will melt out (Application : Induction furnace)
• Due to these induced currents a strong eddy force (or torque) acts on metal body which always apposes the
translatory (or rotatory) motion of metal body, according to lenz.
• Tr a n s f o r m e r
Cause : Transformer core is always present in the effect of alternating magnetic field (B = B0sint). Due to this
eddy currents are produced in its volume, so a part of magnetic energy of core is wasted as heat.
R e m m a d y : To minimise these losses transformer core should be laminated. with the help of lamination
process, circulation path of eddy current is greatly reduced & net resistance of system is greatly increased. So
these currents become
E 29
JEEMAIN.GURU
JEE-Physics
R-L DC CIRCUIT
Current Growth R L
I
dI + –
(i) emf equation E IR L E switch
dt
(i i i ) Just after the closing of the key inductance behaves like open circuit
(iv) Some time after closing of the key inductance behaves like simple R
+ – ( )
connecting wire (short circuit) and current in circuit is constant.
E
Short circuit, t , I I0 , Inductor provide zero resistence I 0
R
L
It is a time in which current increases up to 63% or 0.63 times of peak current value.
R sec .
I0 I0 1
I = I0 (1 – e–t/), t = T, I = = I0 (1 – e–T/) e–T/ = eT/ = 2
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
2 2 2
T L
logee = loge2 T 0.693 T 0.693
R sec .
dI E t / dI E dI
dt L (e ) t = 0 dt t = dt 0
max L
Note : Maximum or initial value of rate of growth of current does not depends upon resistance of coil.
30
E
JEEMAIN.GURU
JEE-Physics
Current Decay R L 0
dI
(i) Emf equation IR L 0 2 1
dt
+ –
(ii) Current at any instant E
Once current acquires its final max steady value, if suddenly switch is put off then current start decreasing
exponentially wrt to time. At switch put off condition t = 0, I = I0, source emf E is cut off from circuit
I I 0 (e t / )
E
Just after opening of key t = 0 I = I0 =
R
dI E t / dI E dI
dt L e t = 0 = t dt 0
dt max . L
Current decay :–
I
t=0, I = I0 =(max)
Node-6\E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Unit No.-10\EMI & AC\English\02 EMI.p65
E 31