Professional Documents
Culture Documents
Rural Ws Technical-Manual - 589475bfb146a
Rural Ws Technical-Manual - 589475bfb146a
Improvement Programme
(World Bank Assisted)
Technical Manual
February, 2015
2
CHAPTER 4 TYPES OF SOURCES FOR WATER SUPPLY 27-53
4.1 Hydrological cycle
4.2 Ground Waters
4.2.1 Tube Wells
4.2.2 Driven Well (Hand Pumps)
4.2.3 Springs
4.2.4 Percolation Wells
4.3 Methods of Drilling
4.3.1 Percussion Drilling
4.3.2 Direct circulation Drilling
4.3.3 Reverse circulation Drilling
4.3.4 Down the Hole (DTH) Hammer Drilling
4.3.5 Hand Boring
4.3.6 Selection of Drilling Rigs
4.3.7 Classification
4.3.8 Selection
4.4 Well casing
4.4.1 Coating of Tubes
4.4.2 Types
4.4.3 Material
4.5 Design features
4.5.1 Length of screen
4.5.2 Diameter of screen
4.5.3 Slot size
4.6 Guidelines for selection of slot size
4.6.1 Determination of slot size
4.7 Gravel packing
4.7.1 Need for gravel packing
4.7.2 Criterion for gravel packing
4.7.2.1 Choice of strainer
4.7.2.2 Particle size Distribution
4.7.3 Pack Aquifer ratio
4.7.4 Thickness
4.8 Methods of Development
4.8.1 Over Pumping
4.8.2 Compressed Air
4.8.3 Calculation of Discharge
4.9 Verticality and Alignment
4.9.1 The condition that cause wells to be out of plumb are
4.9.2 The measurement made are of the plumbness and straightness of the
cased bore
4.9.3 In case of gravel
4.9.4 The verticality of tubewell
4.9.5 For tubewells encased with pipes
4.9.5.1 Verticality of the tubewell
4.9.5.2 The verticality of the tubewell is to be tested
4.9.5.3 If cylindrical space „G‟ of the actually constructed tubewell is equal
4.9.5.4 As an example, cross sections of two tubewell G1 and G2
4.10 Maintenance of Tubewell
4.10.1 Factors affecting well performance
4.11 Preventive Design features
4.12 Maintenance Planning
4.12.1 Interpretation of observed or measured changes in well Performance or
condition
4.13 Well Rehabilitation and Abandonment well Rehabilitation
4.14 Surface waters
CHAPTER 5 PRELIMINARY SCHEME REPORT 54-55
5.1 Reconnaissance
CHAPTER 6 DETILED ENGINEERING FOR A RURAL WATER SUPPLY 56-78
SCHEME
6.1 Surveys
6.1.1 Total station survey system (TSSS)
6.2 Selection of source
6.3 Ground water based schemes
3
6.3.1 Tube Wells
6.4 Water works structure
6.4.1 Pump chamber cum staff quarter
6.4.2 Storage Tank
6.4.3 Pumping Machinery
6.4.4 Criteria for Pump Selection
6.4.4.1 Limitation on Section Head
6.4.4.2 Pump efficiencies
6.4.4.3 Pump Installation
6.4.4.4 Accessories
6.4.4.5 Electrical connection
6.4.4.5.1 Safety Procedures
6.4.4.6 Pump operation
6.4.4.7 Trouble Shooting and Remedial measures
6.4.5 Disinfection plant
6.5 Transmission
6.5.1 Hazen Williams formulae
6.5.2 Coefficients of roughness
6.5.3 Resistance due to specials and appurtenances
6.5.4 Pipe materials
6.5.5 Depth of cover
6.5.6 Hydraulic testing of the Pipeline
6.6 Appurtenance
6.6.1 Sluice valves
6.6.2 Butterfly valves
6.6.3 Scour valve
6.6.4 Air valves
6.6.5 Reflux valves
6.6.6 Anchor Blocks
6.6.7 Water Hammer
6.6.8 Economical size of Pumping main
6.7 Environment Management Framework
6.7.1 Environmental Data Sheets on Water Supply and Sewerage Schemes
6.7.2 Environmental Categorization of the schemes
6.7.3 Environmental Appraisal and approval
6.7.4 Environmental Management Plan (EMP) for pre-planning,
construction and O&M phase impacts
6.7.5 Provision for Environmental Cost
6.7.6 Flow chart of EMF activities
6.7.7 Key Performance Indicators
6.7.8 Training and Capacity Building
6.7.9 Environmental Code of Practices
CHAPTER 7 DISTRIBUTION SYSTEM 79-88
7.1 Planning and Design over head services Reserviors
7.1.1 Capacity and location
7.1.2 Staging
7.1.3 Shape
7.1.4 Standardized capacity and sizes of Pipes
7.1.5 Pipe connection for inlet, outlet, Scour, over flow etc.
7.1.6 Accessories
7.1.7 Design Principles
7.2 Distribution System
7.2.1 Hydraulic Network Analysis
7.2.1.1 Supervisory Control and Data Acquisition (SCADA)
7.2.2 Input data
7.3 Types of valves & their location
Sluice Valaves
Butterfly Valaves
Scour valves
Reflux valves
Pressure Reducing valves
Air valves
7.3.1 Location of the Air valves
7.4 House service connection
4
7.5 Distribution of water
7.6 Design Approach for Water Supply Schemes in Severe Power
Shortage areas
CHAPTER 8 WATER TRTEATMENT 89-94
8.1 Water treatment
8.2 Intake structures for surface water
8.2.1 Intake works
8.2.2 Inlet channel
8.3 Storage and sedimentation of surface water
8.3.1 Suction and Scour wells
8.3.2 Pumping units
8.3.3 High level Tank
8.4 Filters
8.4.1 Filtering media
8.4.2 Pressure Filters
8.5 Clear water Reservoir
8.5.1 Over head service Reservoir (O.H.S.R.)
8.5.2 Disinfections
8.6 Priority levels for Technical options for water quality
CHAPTER 9 ASSESMENT OF EXISTING SYSTEM 95-98
9.00 Assessment of Existing System
CHAPTER 10 SEWERAGE SYSTEM 99-110
10.1 Present scenario of wastewater disposal
10.1.1 Preparation of a GP/Vill. wise Liquid Waste Management Plan (LWM)
10.2 What is small bore sewerage system
10.3 Treatment Technologies
10.3.1 Stabilization Pond
10.3.2 Duckweed Pond Technology
10.3.3 Treatment by Tree Plantation /Forestry( Karnal Technology
10.3.4 Root Zone Technology /Wet Land System(RZ)
10.3.5 Aerated Lagoons (AL)
10.3.6 Decentralized Wastewater Treatment System (DEWATS)
10.3.7 Soil Biotechnology (SBT)
10.4 Merits and Demerits of various technologies
10.5 Peak factor
10.6 Disposal Standards
10.7 Environment Management Framework
10.8 Cost of the Solid free sewerage system
CHAPTER 11 RURAL SANITATION 111-119
11 Rural Sanitation
11.1 Use of locally available material for household tolets drain
11.2 Twin pit flush latrine (TPPFL)
11.2.1 TPPFL pits in water logged flood prone and high sub soil water area
and rocky strata
Pits in water logged flood prone and high sub- soil water areas
Pits in Rocky Strata
Pits in Soil with Low infiltration capacity
Pits where space is a constraint
what are the pollution Safeguards
11.2.2 Operation and maintenance of TPPF Latrine
How to operate and maintain & TPPF latrine
Diversion of flow from one pit to another
Removal and Disposal of pits sludge
Do's and Do not's
Observation to be made during construction materials
11.3 Institutional and group Toilets
11.4 Soak Pit
Calculation of Percolation Rate
11.5 Pucca drains
Layout of drains
Surveying and data collection
CHAPTER 12 OPERATION AND MAINTENANCE OF WATER SUPPLY 120-129
SCHEMES
12.1 Maintenance of source
5
12.2 Maintenance of Pumps
12.3 Maintenance of treatment units
a) Maintenance of slow Sand filter
b) Maintenance of Setting tank
c) Operation & Maintenance of disinfection systems
C1 Differential pressure chlorinator
12.4 Maintenance of pumping main
12.5 Maintenance of OHSR/ UGSR
i Cleaning operation
ii Safety precautions
12.6 Maintenance of Distribution system
12.7 Maintenance of structure, Lawns, clean Environment
12.8 Duties of Pump operators Maintenance of record
i Log Book
ii Complaint Register
iii Movement Register
iv Meeting register with Panchayats
v Chlorination Register
12.9 Annexure of Model O& M calculation for village water supply scheme
12.10 O& M cost estimate
General
1. Salient Details of Scheme
a) Requirement of water
b) Source
c) Storage
d) Distribution system
2. Cost of Scheme
3. O&M cost payee
4. Annual Maintenance and repair
CHAPTER 13 CONSTRUCTION MANAGEMENT 130-144
13.1 Sequence of construction
a) Source
b) Civil works
c) Testing of Materials
d) Construction Management
e) Payment Schedule to Contractor
f) Commissioning & Trail Run
13.2 Check list for construction quality management at site
13.3 Formats for test report
CHAPTER 14 SPECIFIC WATER TREATMENT PROCESSES 145-149
14.1 Deflouridation of Water
14.1.1 Flouride exchangers
14.1.2 Anion exchangers
14.1.3 Magnesium salts
14.1.4 Aluminium slats
14.1.5 Simple method of flouridation
14.2 Reverse osmosis
14.2.1 Consultancy support for RO plants
14.3 Pressure filters
CHAPTER 15 COMPLETION PLAN AND REPORTS 150-153
15.1 As built drawings/completion drawings
15.2 Completion reports
15.3 Exit Strategy for Multi Village Water Supply Schemes
CHAPTER 16 RAIN WATER HARVESTING 154-159
16.1 Design considerations
16.1.1 Interception and collection
16.1.2 Groundwater recharge system
16.1.3 Recharge pit
16.1.4 Recharge well
16.2 Operation and Maintenance
ANNEXURES A TO O 160-227
Drawings 228-267
Abbreviation 268
References 269
6
CHAPTER – 1
INTRODUCTION
Water is called the life stream of a community. The supply of safe water to the community in
adequate quantity and quality is one of the important responsibilities of a civic body.
1.1 Objective:
The overall project development objective is to assist Government of Punjab in
improving the quality of rural water supply and sanitation service delivery to achieve
sustainability of investments. Specifically the objectives would be to institutionalize on a
significant scale, decentralization of Rural Water Supply and Sanitation (RWSS) service
delivery to Gram Panchayats and user group and build the State‟s capacity to scale up the
new decentralized services delivery model statewide.
The Punjab Rural Water Supply and Sanitation Sector Improvement Programme , aims at
improving the quality of life in rural area by RWSS service standards. The project will
adopt a demand response approach and use of participatory process and change the role
of Government at all levels from direct service provider to that of a facilitator.
In the Punjab Rural Water Supply and Sanitation (RWSS) sector, present
key issues are:
1) Poor operational performance of existing RWSS facilities due to lack of funds
coupled with declining ground water sources and deteriorating/poor water
quality.
2) Poor sanitation coverage and poor management of existing facilities.
Some of the above issue can be traced to inadequate planning and designing of
the existing Rural Water Supply and Sanitation facilities.
1.2 Objectives of the technical manual:
The main objective of this technical manual is to develop guidelines to plan,
design, construction, operation and maintenance of water supply and sanitation
facilities to be developed/strengthened under the project. The technical manual is
produced in a user friendly manner with simple text, sketches / drawings, type
designs, rate analysis, estimates etc.
1.3 Scope of the Technical Manual:
The technical manual contains: The significance of water quality, population
forecast, design criteria for all technology options for Rural Water Supply and
Sanitation schemes, requirements, procedures and guidelines for selection of
sources for water supply, methods of field survey and investigations along with
guidelines for planning ground water recharge facilities.
Requirements, contents and formats for preparation of Preliminary Scheme
Report (PSR), Detailed Scheme Report (DSR), Standard designs, drawings, cost
estimates and specifications for typical work & installations proposed under the
project such as water supply, sanitation (latrines), lane improvements, drains and
other works
1.4 Methodology to be adopted for preparation of estimates:
Common schedules of rates used by the Water Supply department along with
latest ceiling premium shall be used to obtain rates of items covered in the
common schedule of rates. However market rates items/goods not covered in
CSR shall be obtained by committee of officers from the current price list issued
7
by by reputed manufacturers will be basis for preparation of cost estimates. For
the sake of uniformity for plain, kandi, water logged areas analysis of the rates
should be prepared and circulated either at zone level or jointly for all zones for
estimating purpose only. Water Supply and Sewerage project shall be carried by
single responsibility contract system.” However, wherever field conditions
warrant more than one package, approval of the concerned Chief Engineer should
be accorded citing reasons for the same and a copy of the same should be sent to
the Programme Director for record by the concerned Chief Engineer.No
centralized purchase of machinery pipes etc shall be carried out . No rate contract
shall be carried out with manufacturers or suppliers of materials to be used in the
water supply and sanitation project.
Inspection /Testing to be done by the engineers to ensure the goods and works
are in conformity with the specification.
Engineer-in-charge wherever feels necessary for testing of the construction
material and untreated / treated effluent the same shall be got tested from nearest
NABL approved laboratory which can be traced from the internet. Quality of
water sources, shall be got tested from the DWSS laboratory.
1.4.1 Who can use the Manual?
This manual is meant for the following categories of users:
Gram Panchayat functionaries and GPWSC members involved in planning and
implementing the project.
Govt. agencies and consultants involved in planning and implementing the
project.
Agencies / persons involved in technical administration approval of the project.
Non-government Organization and Support Agencies involved in planning and
implementing the project.
Besides this, manual can also be used as a guide for conducting training programs
for the above functionaries.
1.5 Limitations for Manual:
The use of the manual is limited to the World Bank Assisted Punjab Rural Water Supply
and Sanitation Sector Improvement Programme with the project philosophy, design criteria and
site-specific conditions of the project villages. This manual is an attempt to start the project
activities and learning from the project implementation, the guidelines contained in this manual
will be modified, if necessary, as the project implementation proceeds.
8
CHAPTER-2
WATER SUPPLY
This chapter contains the basic design criteria for rural water supply systems, significance
of water quality, quality standards, scientific selection of sources and assessment of yield of water
from sources.
The basic minimum design criteria to be followed in this project are discussed below.
(See Annexure -B)
The design per capita supply shall be of @70 Lpcd (with addition of 15% as water losses)
for all types villages. However if any habitation / village wants to design water supply scheme at
higher per capita water supply rate they shall be allowed to do so with the condition that it bear
all the incremental cost required in addition to basic 10% share . Water demand shall be
calculated for the projected population for the design period of the project which is 30 years for
rising main and distribution lines and 15 years for water works structures and machinery.
In a community water supply system, the O & M cost is to be borne by the users. To make the
scheme self sustainable, the community shall be encouraged to have house connections so that
maximum revenue is realized from the users.
In fluoride affected areas or in water scarcity areas, the minimum per capita supply can be
modified after discussion with the community. In some areas, if fluoride free water is to be
transmitted over long distances, it may be expensive to operate and maintain and the community
may not be able to afford the high user charges. In such cases, the feasibility of dual policy with
reduced per capita supply of fluoride free water for cooking and drinking only (about 10 Ipcd) and
supply of fluoride water for all other uses as mentioned above with appropriate per capita supply
can also be considered.
The sources for water supply are Deep tube wells or irrigation canal water where potable water
is not available from deep tube wells . In Kandi area of Punjab springs /infiltration galleries may
also be used as source of drinking water .. In Punjab a rural water
supply schemes have been traditionally designed based on Tube wells. However, where the
quantity of ground water is insufficient or quality of ground water is not of required standards,
surface sources are chosen depending upon the availability. The rural water supply schemes with
bore wells and open wells are economically viable and easy to operate and maintain, whereas
schemes designed with surface water as source are not economically viable are often difficult to
operate and maintain by the Rural Communities. Hence, in order to make the surface source
schemes viable, which required skilled operation and maintenance, it is preferable to design
schemes with surface sources for a group of 3 to 4 villages. In cases wherein the surface water is
to be transmitted from a long distance and wherever limited quantity of ground water is available
dual supplies for such villages shall also be examined thereby satisfying both quality and quantity
requirements.
9
2.1.2.1 Water Quality :
The drinking water required to the community shall conform to the relevant clauses so as
minimize health hazards to the community. The quality of water supplied shall satisfy the criteria
contained the CPHEEO manual, which are reproduced in this chapter at Annexure- J..
2.1.3 Storage:
Capacity of OHSR shall be calculated by Mass curve (Refer annexure- O)method keeping
in view the realistic availability of Electricity and water supply hours . Two number typical mass
curves are enclosed as sample for different types of conditions of availability of electricity . As
electricity is available for longer hours hence it is being proposed to pump water for atleast 8 to
12hr. Pumping hours will vary as per availability of electricity . Hence before fixing the capacity
of OHSR mass curve should be plotted for all the three shifts pumping of water and supply hours
. OHSR capacity should be worked out for worst case scenario. The tank shall be located such
that the minimum residual pressure at the remotest point in the village is at least 12 mts. If
elevated lands are available at a reasonable distance, ground level reservoirs can be proposed for
storage of water. If such location is not available, an elevated service reservoir can be proposed
with staging such that it gives a minimum residual pressure of 12 mts after counting for loss of
head during peak hours due to simultaneous opening of the all the taps on the distribution system
2.1.4 Treatment :
Ground waters, which are free from odour and colour and turbidity problems, can be
supplied after plain disinfection by chlorinating. Surface waters may require conventional
treatment consisting of sedimentation, filtration and disinfection.
The treatment proposed for water shall be such that it is easy to maintain and operate by the
village community. Presence of fluorides requires treatment to remove fluorides, which is not
easy for the community to operate and maintain the treatment scheme. Nitrates and TDS cannot
be removed in conventional Treatment System. Iron presence, though amenable, its removal
becomes difficult and the plant is uneconomical to the community to maintain.
Disinfection of water supply shall be carried out with Bleaching powder/ Sodium Hypocholorite
using diaphragm based dosing pumps etc. „Dosatron‟ which uses Chlorine dioxide and is non-
electricity system can also be used to carry out disinfection of water supply.
The project proposes to have piped water supply schemes in all the villages covered in the
project. It is expected that there will be substantial demand for individual house connection.
Hence, pipe network in the form of dead/loop system (which is mostly suitable for rural areas)
shall be planned. For the benefits of community not opting for house connection stand post shall
be provided at appropriate places @ one per 150 persons in the villages How ever as explained
above use of stand posts shall be discouraged as it results in avoidable wastage . As electricity is
available for longer hours, it is proposed to pump water for atleast 8 to 12hr. The storage capacity
of service reservoir shall be taken on the basis of mass curve plotted or 30% of the daily
requirement.
10
2.1.5.1 Water Supply Duration and Peak Factor :
Usually water supply is made twice/thrice a day to the village community at the rate of 3 hrs
each time which is equal to 6 hrs. Considering improvement in availability of electricity, water
supply schemes will be designed for 8 to 12 hr. pumping. It may be further kept in mind that
demand of water is more in the morning which may be 1.25 –2 times of the average daily demand
. CPHEO manual recommends following peak factors for various population figures:
, For rural water supply distribution scheme, CPHEEO manual recommend the design peak factor
for 4 times of average demand ( duration of supply is 6 hours).
Hence irrespective of the population of the village, supplying hours, the peak factor for designing
of scheme shall be taken as 3.0.
The size of distribution pipe shall be calculated on the basis of discharge to be carried by
the pipe line , pressure requirement and number of connections to be drawn form the pipe by
using following formula :
Where „D‟ is diameter of main pipe and „d‟ is the diameter of branch pipe
e.g. if diameter of main pipe is 150 mm and branch pipe is 90 mm then number of branch pipe
connections= 2.78 say 3
- Size of branch pipe shall also be checked for number household private connections and
stand posts to be proposed on the branch line using the following formula :
-
Number of Connections =[ D2/d2]
11
In case of Rural Water Supply Schemes for multi villages the transmission main from the
water works running along Phirni(village ring road ) shall not be used as distribution main . The
delivery main and distribution system in village should be so proposed that supply to Ist village
and any intermediary village /villages is given from only one point on the delivery main and that
the delivery main should not be made a part of the distribution system of the Ist or intermediary
village /villages . This will ensure equitable water supply to all the villages as supply to individual
village can be regulated at one point using the sluice valve . No private connection or stand post
should be allowed on the transmission main . (Refer CE Rural Water Supply circular no 34028-
34PH/W dated 6.7.78)
2.1.7 Pumps :
Submersible pumps shall be provided for all borewells and centrifugal pumps/submersible pumps
for canal based water supply schemes . While calculating the capacity of pump, the resulting
suction head, delivery head and frictional losses shall be considered appropriately. Only
commercially available pump capacities shall be adopted in the project.
Normally Standby pumps are not proposed in rural water supply systems based on borewells and
for other sources. Standby pumps shall be provided only in exceptional circumstances. In such
cases if the number of pumps installed are more than one, then one standby pump is suggested.
For economical selection of the pump, the actual pump capacity required shall be worked out
using the family curves furnished by pump manufacturer. However, in arriving at economic size
of rising main only overall efficiency of pumps can be taken as 60 % for submersible pumps and
65 % for centrifugal pumps.
Note :
All the above referred design parameters are mentioned in Annexure – B Titled as Design
Standards both for Tube well based schemes and canal based schemes
12
2.1.8. Ground Water Recharge Measures :
Due to continuous and over extraction of water from ground, there will be a possibility of drying
up of source well in the summer months. Hence, proposals are to be included in the water supply
scheme for recharging of ground water through artificial recharge measures depending upon the
geological conditions of the area. Possibilities of using Rain water harvesting as a source and roof
water harvesting shall also be explored in the project areas. Rain water harvesting shall b e used
to recharge shallow aquifers as deep aquifers cannot be recharged as deep aquifers are artesian
aquifers . By recharging shall aquifers static water table level shall be increased which will cause
saving in electricity as head required to pump water shall decrease which will reduce electricity
consumption . Various ground water recharge measures based has been explained in chapter :16
of this manual .
The quality of drinking water affects health of the consumers because certain diseases and toxic
chemical compounds may be transmitted by water. Experience has shown that community health
and supplied water qualities are directly related to each other and that an improvement of water
qualities of drinking water supply is followed by an improvement in the community‟s health.
Hence, the water supply systems shall provide water that is safe and available in adequate
quantity. A water supply engineer is expected to know what diseases are waterborne, what are
toxic chemicals and how they get in to water supplies.
2.2.1 Definitions :
While describing water quality, certain terms are frequently used which are to be clearly
understood and correctly used. Some of the definitions that are commonly used are given below.
13
ii) Water Contamination :It is the introduction of toxic materials, bacteria, or other
deleterious agents into water that make the water hazardous and therefore making it unfit for
human use.
iii) Safe water : It is the water that can be consumed without menace to the health of the
consumer. Sometimes the word pure water is used which is incorrect, in the sense that there
exists no pure water.
iv) Potable water and wholesome water : Potable water is the water that is satisfactory for
drinking purposes from the standpoint of its chemical, physical and biological
characteristics and is also known as „wholesome‟.
v) Palatable water : It is the water that is appealing to the senses of taste, sight and smell.
Palatable water need not always be potable.
vi) Water-Natural State : Water in nature is never hundred percent Hydrogen and Oxygen, it
always contains mineral matter in solution or suspension or dissolved gasses.
vii) Parts per million (ppm) or milligrams per litre (mg/lt): These terms are used to express
the concentrations of dissolved and suspended matter in water. The Parts per million (ppm)
is a weight to weight relationship. Except in highly mineralized water this quantity would be
same as mg/lt. This is preferable since it indicates how it is determined in the laboratory.
viii) pH of water : It is an indication of the hydrogen ion concentration the water. Alkaline water
will have pH of above 7; while acidic water will have pH of below 7; whereas water with
pH 7 is neutral.
x) Physiological Effects : These are the effects which change the normal functions of the
body.
xii) Bacteria : These are groups of universally distributed, essentially Unicellular micro
organisms, lacking chlorophyll.
xiii) Coliform bacteria : These are groups of bacteria predominantly inhabiting the intestines
of human beings and animals but also occasionally found elsewhere. Their presence
indicates pollution of water by sewage.
xiv) Enteric : Having its normal habitat in the intestinal tract of human beings or animals.
xv) Virus : The smallest form of bacteria capable of producing disease in human beings.
xvi) Chlorine residual : Chlorine remaining in the water at the end of a specified period.
xvii) Chlorine demand : The differences between the amount of chlorine added to water and
amount of residual chlorine remaining in the water at the end of a specified period i.e. after
total disinfection.
2.2.2 Water and health of community :
Community‟s health is affected by drinking water quality because –
14
(i) Certain disease causing bacteria are enteric and survive long enough in water to infect the
water users.
(ii) The excreta of human beings and warm-blooded animals contain bacteria harmful to human
beings, and these bacteria can find their way into drinking water sources.
(iii) Chemical substances affecting the health of people can also enter drinking water sources.
Water free from both bacteria and dissolved chemicals is seldom found in nature. Water
falling as rain, snow or hail washes impurities out of atmosphere; some of these may be present as
solids or some may be dissolved. The first water that falls tends to be higher in material removed
from atmosphere than that falling later. Even prolonged rainfall may not completely clear the air.
Rain water and snow may have dissolved solids as high as 150 mg/lt and total hardness up to
40mg/lt. In industrial areas due to air pollution carbon dioxide dissolves into rain water. This
phenomenon is known as Acid rain. Normally, the pH value of rainwater is 6.7 to 6.9. Rainwater
is also saturated with dissolved oxygen from the atmosphere.
Water that is clear and colorless gives an impression that is safe for human consumption. This
may not be correct, since both disease causing bacteria and objectionable matter may be present
but invisible to naked eye. Water quality parameters are classified as physical, chemical and
biological nature. The environmental significance of some common parameters of water quality is
given below:
Turbidity :
Any turbidity in water is associated with pollution and associated with health hazards arising out
of it. Increased turbidity makes treatment difficult and costly due to increase in chemical
coagulation costs and increased frequency of cleaning the filters. In turbid waters the pathogenic
organisms may be trapped in the turbid particles and hence protected from the disinfectant.
Ground water is less likely to contain turbidity. Turbidity of surface water may settle down by
plain sedimentation.
Colour :
Natural colour may be acquired by water from decay in swamps and forests; but the colour may
not be harmful. The fact is that if the potable water is having colour and hence aesthetically not
acceptable, the consumers tend to seek water from other sources which may not be safe. Ground
water is less likely to contain colour and surface water may contain colour due to industrial
activity. However colour is not removed in conventional treatment adopted in Rural Water
Supply Schemes.
15
Taste and Odour :
Both should not be noticeable to consumers. Taste is not measurable but should not be
objectionable. For odour, Thresh hold odour numbers (TON) are given to indicate the dilutions
required for the odour to disappear. It should be preferably one and not greater than three.
However, odour is not removed in conventional treatment adopted in Rural Water Supply
Schemes.
Water that contains mineral acidity is unpalatable. Acidity causes corrosion and affects the
consumption of chemicals in water softening.
Alkalinity :
Measures the content of bicarbonates, carbonates and causticity of waters. Waters that contain
high alkalinity are unpalatable. Chemically treated water sometimes may have high alkalinity.
Alkalinity is important in coagulation and corrosion control. However alkalinity is not removed in
conventional treatment adopted in Rural Water Supply Schemes.
Hardness :
Waters with TDS of less than 500 mg/lt are suitable for domestic use. Waters with higher TDS
have a laxative effect upon people who are not accustomed to it. Conventional treatment methods
don‟t address the removal of TDS. This can be removed only through distillation and reverse
osmosis membrane filtration, However TDS is not removed in conventional treatment adopted in
Rural Water Supply Schemes as this is not economically viable and cannot be maintained by the
rural communities.
Chlorides :
Chlorides impart salty taste if present beyond 250 –mg/lt. Unusual presence of Chlorides in water
indicates contamination of ground water with wastewater. However Chlorides are not normally
removed in conventional treatment adopted in Rural Water Supply Schemes.
Nitrogen salts :
They may be reported in the form of free ammonia and Nitrates (nitrates in terms of Nitrogen).
When present beyond trace amounts, indicate pollution by human wastes. Water containing
16
organic and ammonia nitrogen indicate recent pollution ; water-containing nitrogen in the form of
nitrates indicate pollution; water-containing nitrogen in the form of nitrates indicate pollution that
has occurred a long time back. Waters with appreciable amounts of nitrites are of questionable
character. The amount of ammonia nitrogen determines the efficacy of chlorinating. Nitrates in
water may be due to „agricultural run off „water source, due to fertilizer use, leaches from septic
tanks, sewerage and erosion of natural deposits. Excessive amounts of nitrates in drinking water
causes „blue baby syndrome disease‟ (methaeamoglobineamia) in infants under six months which
is a threat to life if immediate medial attention is not available. The infant looks blue and has
shortness of breath. However Nitrates are not removed in conventional treatment adopted in Rural
Water Supply Schemes.
Dissolved Oxygen :
Dissolved Oxygen (DO) is of significance in corrosion of iron and steel particularly in distribution
systems. However DO is not removed in conventional treatment adopted in Rural Water Supply
Schemes.
Fluorides :
Minimum of 1 mg/lt may be required to prevent dental carries; but beyond 1.5 mg/lt may cause
staining of teeth/dental fluorosis and also skeletal fluorosis. Treatment units set up in India for
removal of excessive fluorides in Rural water supply schemes are so far not functioning
satisfactorily.
Iron :
Iron may be present in water as a dissolved impurity from the earth‟s crust or enter the water
supplies from corroded pumps and pipes. Excess iron may cause staining of clothes during
washing, stains on plumbing fixtures and encrustation and deposits on the interior surfaces of the
pipe. Treatment units set up in India for removal of excessive Iron in Rural water supply schemes
are so far not satisfactory.
Manganese :
Barium : Even at 1 mg/1 it causes muscular and cardiovascular disorders and Kidney damage.
Cadmium : At low levels and exposure for prolonged periods it causes high blood pressure,
sterility among males, kidney damage and flu like disorders.
17
Lead : Beyond 0.05 mg/1 it causes brain and kidney damage. In youngsters it may cause mental
retardation.
Mercury :At very low concentration it forms methylated mercury compounds Which are toxic to
human beings and fish.
Silver : Has no adverse effect but silver salts are good disinfectants.
Arsenic, Selenium & Cyanide : They are toxic and carcinogenic, However none of the trace
elements are removed in conventional treatment adopted in Rural Water Supply Schemes.
Bacteria : Diseases caused by waterborne bacteria are always intestinal and include typhoid,
dysentery, cholera and gastro-enteritis.
Slow sand filtration may remove bacteria and viral contaminants. Disinfection with bleaching
powder, chlorine dioxide or any other disinfectant alone makes the water wholesome. However,
due to labour problem for regular sand washing of slow sand filters, continuous sand filtration
should be preferred.
Water safety and quality are maintained through water treatment, disinfection and prevention of
pollution and contamination. Rural water supplies are normally disinfected using bleaching
powder, which makes the water wholesome. However, it will be necessary to search for sources
of contamination and prevent such contamination of drinking water supplies.
Surface run off comes into contact with wastes containing pathogenic bacteria or the storage
reservoirs may get inflows of domestic sewage and or industrial effluents. Contamination from
domestic waste can enter the raw water sources such as borewells or open wells. Casing pipes for
sufficient depth can prevent such entry of wastes into borewells. Watertight seining has to be
proposed for sufficient depth to prevent entry of such wastes into the open wells. Harmful wastes
can also enter the water distribution systems through cross connections or back-siphonage
conditions. A systematic sanitary survey can be undertaken to identify the sources of
contamination and preventive measures taken where necessary.
18
sources and red colour for non potable sources) of the sources in the village (using
geographical/global positioning systems).
3) Latest water supply analysis (physical, chemical and biological tests)/water quantity yield
results of all working sources should be incorporated in the report enclosed as Annexure I.
4) Compare the latest water quality results with old available data (secondary data from
Water Supply and sanitation department ) and find out the difference.
5) Justify the proposed source details from the quality angle. Also mention the distance of
this source from the existing potable/non-potable sources.
After the water quality report is received the parameters may be compared with the
standards and if the water satisfies the standards the same source can be accepted with
disinfection only. If fluorides and TDS are present in excess of permissible limits, dilution if
possible can be one of the options. Conveying potable water from distant source either surface or
ground water can also be other option. If nitrates and iron are higher, it is necessary to search for
the source of contamination and take remedial measures.. However, treatment of such water for
removal of iron and nitrates is not a viable option in villages. If the contamination is not traceable
and if the presence of iron and nitrates is due to natural acquisition, then another source is to be
selected. Use of PVC casing pipe avoids corrosion, also extending the casting pipe up to 12 m
will enable prevention of ingress of nitrates. Treatment for removal of fluorides and Iron shall be
the last option since the rural community cannot operate and maintain such treatment plants.
The exploration methods that can be adopted to locate the ground water are :
1) Geological methods : Demarcating the boundary between lithologic units, faults, fractures,
fissures, formation characteristics, lineaments, and dykes, intrusive and shear zones.
2) Remote sensing techniques: Interpretation of satellite images to locate lineaments and
other structural discontinuities, mapping of various hydrogeomorphic unit, vegetation,
soil, and land use and land cover categories.
3) Geophysical methods : Surface geophysical surveys using electrical resisvity,
electromagnetic, seismic and magnetic methods to delineate the weak and water-saturated
zone.
2.2.9 Geophysical exploration:
Geo Physical methods comprise measurement and interpretation of signals from natural or
induced physical phenomenon generated as a result of a sub-terranean formation .These signals
19
measured repetitively at several points of space and time are approximately interpreted,
considering the available geological information , in terms of such sub-surface structures /features
as may themselves have good ground water potential or are indicative of good aquifers
.Knowledge of the geology of ground water areas is essential to establish the water bearing
formulations. Surface geology, exposed due to quarrying, mixing etc. provide useful information.
Well logs of existing wells (records that give the nature and depth of various strata that were
encountered during sinking of the wells) also contribute as a supplementary information in
assessing the nature of the sources being explored.
2.3 Geomagnetic :
Measurements of variations of gravity and of the earth‟s magnetic field are made with the aid of
the torsion balance and the magnetometer. These instruments donot determine the presence of
water itself. They suggest the location of geological structures that may be favourable water
carriers.
2.3.1 Acoustic and Seismic :
Acoustic and Seismic methods measure the speed of travel and sound and shock waves through
the underground formations. Dependence of wave velocity upon the density of the materials
through which it passes makes it possible for a geophysical analysis of the test area. This also
indicates the presence of water in the test area being explored for water. Measurements are made
as wave reflection for deep strata exploration and on wave retraction when water bearing
formation is near the surface of the earth.
It is essential to take the assistance of the departments/agencies experienced and engaged in such
investigation to assess the water potential for selection of a suitable ground water source for the
community water supply.
Resistivity data for rock formations in Punjab
20
The yield of borewells is to be assessed preferably in the lowest seasonal water level conditions.
In Punjab, the preferable season for conducting yield test is from April to June, when the summer
is at its peak and rainfall has not yet set in. Yield test units are available which can be used to
pump out the water from the borewell for a maximum period of six hours at a time. Care should
be taken that the water pumped out is led away from the source and does not re-enter the source.
The draw down and discharge are measured and the results tabulated from which the safe yield is
calculated. The assessed yield is multiplied by a coefficient to arrive at the safe yield from the
source to account for the seasonal variations and also to prevent over exploitation from the
borewell, which may lead to collapsing of the borewell. In case the yield test is conducted during
non-summer months, a suitable coefficient for assessing the safe yield has to be used. While
drilling the bore wells, it is essential that a correct record of the strata of the borewell and the
depths of water column are noted in a dated long book and this record must be made available at
the GP. Maximum permissible size of pump to be installed in the Tube Well should be clearly
mentioned at the wall of the Pump chamber to prevent over pumping from the Tube well
For assessing the yield from infiltration wells sunk in the riverbeds the same methods as described
above is used for determining the safe yield from the source. In the case of canals, the levels at
which water can be made available and the quantum of water and the period for which the canal is
flowing are used to assess the sizes of various components of the water supply scheme.
Supply of safe drinking water in adequate quantity to the public is a prime responsibility
of a civic body. This task could be achieved if and only if the water supply agency is adequately
equipped with necessary infrastructure for routine water quality monitoring and control. Presently,
there is no agency with a well defined mandate for routine water quality monitoring and control of
rural water supply in the State. The EE in- charge checks the potability of any newly established
tube wells / surface source by conducting all the tests on the water samples collected. If the
quality parameters are within the prescribed limits, the source is developed and allowed to be used
by the community. If the water does not satisfy the required quality parameters, new bore wells
are drilled after conducting detailed geophysical surveys. In areas where ground water is not
potable canal based schemes are designed. Raw water is collected from canals and after treatment
supplied to the community . It is very important that a suitable mechanism should be adopted to
have regular quality surveillance . During rainy season water quality surveillance should be more
stringent .
21
points . He shall visit peoples houses at regular intervals and check the residual chlorine available
in their house . He shall maintain record of checking as per below sample performa .
Date Name and Location of Residual Residual Name and
designation of Sampling Chlorine chlorine address of the
sampling Point present in the present in the person who
officer/official sample sample drawn was resent at
at water the time of
works sampling and
his signatures
a. Objective :
i. To ascertain the quality of water in various rural water supply schemes (Tubewells or
canal based) as well as in the distribution network.
ii. To examine physico-chemical and bacteriological quality to establish whether the
drinking water is fit for human consumption and meets the standards as laid down in
IS - 10500 : 2012 (Second Revision).
b. Location for sampling :
Selection of location for sampling should indicate true representative samples.
i. Public Stand Posts
ii. Selected consumer locations at random
iii. In addition to above, raw water source and treated water should also be analyzed in
case of canal based water supply schemes.
c. Type of sampling :
Generally, for drinking water quality monitoring, grab samples should be preferred.
d. Frequency of sampling :
Mainly depends on population served, size, source and type of the scheme. Frequency of
sampling shall be done as per Uniform Drinking Water Quality Monitoring Protocol of Ministry
of Water and Sanitation, GoI.
Source Minimum frequency of sampling and analysis Remarks
Bacteriological Physical/Chemical
Tubewell Once initially, thereafter Once initially, then 2 Situation requiring testing : change in
based as situation demands. times yearly environmental conditions, outbreak
of water borne disease or increase in
incidence of waterborne diseases.
Canal based Once monthly - Once initially then Increase frequency of bacteriological
2 times yearly. test if situation demands.
- Residual chlorine
test daily
22
II. No significant change in samples between time of collection and conducting water
analysis and samples should be dispatched to lab under iced conditions as soon as
practicable.
III. Samples should be examined maximum within 24 hours after collection.
IV. De-chlorination is prerequisite for sampling for bacteriological examination.
V. No contamination should take place while collecting the sample prior to examination
especially for bacteriological tests. For taking sample of water from a tap on distribution
system, allow the water to run for 4 to 5 minutes to allow cleaning of service pipe.
VI. The water sample shall be collected and its data sheet as per Annexure I should be filled
up along with sample for onward submission to Water quality testing lab .
f. Quantity of sample
i. For physical and chemical examination, two liters of samples in colourless or pale
green bottles.
ii. For bacteriological examination 250 ml sterilized glass bottles provided with
ground glass stopper.
2.5.1.2 Present status of rural water quality surveillance and lab infrastructure proposed
Village level : To make the WQS programme more effective, DWSS is distributing water
testing kits to community based organization i.e. Gram Panchayat Water & Sanitation
Committee (GPWSC), which would mainly the representative of various segment of
community living in the village itself. Further, these GPWSCs would act as an extension of
district/village administration. Under WQS programme, field kits for both chemical and
bacteriological analysis would be provided to 10+2 schools having science stream or in the
primary rural Health Centres. These field kits would mainly indicate the presence of turbidity,
pH, hardness, chloride, fluoride, iron, residual chlorine and bacteriological quality. The field
kit will be basically meant for qualitative assessment of water and would help to identify
unsafe drinking water supply system immediately. In case, water is unfit for drinking, samples
would be sent for detailed investigations to the district labs.
23
District level : In addition to 8 sub. Divisional level lab, 22 district level labs are already
functional. Small portable kit capable of measuring temperature, conductivity, pH and
dissolved oxygen is being provided so to as to carry on the spot tests, besides district labs also
have lab equipments, chemicals and glassware.
State level : One State level water quality testing laboratory is functioning in Public Health
Department Head Office Patiala since 1962. Whereas, DWSS has approved Punjab Pollution
Control Board lab at the State level for any arbitration or reconfirmation of the results.
Further for facilitating effective water surveillance programme, 3 mobile water testing
laboratory is also in operation which independently helps in identification of source of
contamination .
24
CHAPTER-3
POPULATION FORECAST
In this chapter, various methods of population forecast and assessment of the demand for
designing water supply scheme are discussed.
Present population will be available from figure of census for 2011. Forecast of
population shall be calculated based on arithmetic progression, geometric progression,
incremental increase and national average. However, village specific assessment of growth
potential shall be taken into consideration while arriving at the final population forecast.
Population forecast shall be done considering the following factors:
Trend of population growth in the previous decade (from 2001-2011 Census Figure)
Possibilities of village growth due to factors such as industrial projects and other
projects which influence the growth of population.
The population growth in any region can be assessed either through graphical methods or
arithmetical methods as discussed below :-
(Sample calculations for Population forecast are enclosed at Annexure K)
Population forecasts are made by assessing separately the births, the deaths and migration
and then summing them up to get the net effect for the considered projection period.
Diseases, Epidemics, Catastrophic natural calamities and other technological changes are
the possible causes of error in forecasting the population correctly in this method.
This method is based on the assumption that population increase at constant rate. A
Constant increment growth is added periodically, based on the past records. This method
generally gives a low rate of population growth and can be used for villages where the growths
are not conspicuous and practically controlled.
In this method, percentage increase or percentage growth rate per decade is assumed to be
constant, and the increase in compounded over the existing population every decade. This
25
method normally gives larger values of population and is used for areas with unlimited scope for
expansion and where a constant growth rate is expected.
When the various factors affecting the population growth do not change abnormal, the
groups of population follow a „S‟ curve, called a logistic curve.
This method is suitable for areas where the rate of increase or decrease of population with
time is likely to reach a saturation limit ultimately because of specially local factors. The growth
rate of which follows a logistic curve will plot as a straight line on the arithmetic paper, with time
intervals plotted against population in percentage of saturation.
In this method, the average in incremental increase is calculated from the available data.
To the present population, the average incremental increase per decade is added and the
population of next decade is obtained. Like this, the process is repeated till the population in the
desired decade is determined.
This method involves the extension of the population- time curve into the future based on
a comparison of a similar curve for comparable areas and modified to the extent depending on the
factors governing such predictions. The method has a logical background, and if statistics of
similar villages are available, quite precise and reliable forecast can be made. However, it is very
difficult to get identical villages with respect to population growth.
It has been observed that growth of population in rural areas near main cities grows at rate
higher than the rate of growth for other villages . These areas falls under the Peri Urban area
category . It is proposed that in all Rural areas falling under a radial distance of 5 Km from Class
A and B cities population growth rate shall be calculated by Graphical comparison method . In
case no such comparison is available then Population growth rate of such areas shall be
determined by using Geometrical progression method
The design of rural water supply and sanitation schemes shall be based on actual existing
population with realistic projection for the project using the methods described above. However,
the per year growth rate must be taken @ 0.798 % per annum based on census 2011.
Software packages are available for estimation (using the methods described earlier) of
population growth and the same shall be used in the project.
26
CHAPTER – 4
This chapter provides information on various types of sources that can be used for
providing water supply to rural communities.
Ground water has been traditionally the main sources of drinking water in Punjab. With
the advent of drilling rigs and consequent indiscriminate extraction of ground water from
deeper Aquifers, mainly for agricultural purposes, the yield from the Tubewell sources is
depleting at a fast rate. Apart from depleting ground water table, there had been an
increase in concentration of Total Dissolved solids that seriously affect the quality of
drinking water. Hence, there is a need to select the Tubewell sites on a scientific basis,
which will have sustenance as sources of water and amenable for recharge. The
sustainability of the tube wells as drinking water sources can therefore be ensured by
applying the provisions of legislation strictly and appropriate ground water recharge
measures.
4.2.1 Tubewells
Tubewells collect the ground water infiltrated to deeper layers in the soil strata compared
to dug wells and hence the quality of water will be good and can be supplied after
disinfections (using bleaching powder.) Tubewells have been successfully used in rural
water supply in Punjab. This is an acceptable technology option for rural communities
since the irrigation tubewells are being operated and maintained by the communities. The
market facilities are available in the project districts to supply the pumps/spares and also
to provide skilled personnel for repairs and servicing. With the advent of modern drilling
rigs it is possible to drill as much as 300, m below ground level even penetrating hard rock
formations. Submersible pumps fitted to a small diameter pipe are installed in these
Tubewells. Depending upon the entry of water into the well, the tube wells are classified
into cavity tube wells and screen type tubewells.
27
4.2.2 Driven Wells (Hand Pumps) :
Hand Pumps are installed by drilling small diameters pipes up to about-100 M depth as
per India Mark-II /III design. The driving end is fitted with a pointed „drive point
strainer‟. The pipe is connected to a pump or hand pump. These are suited in soft soils, if
ground water is available at shallow depths. All the following standards including
amendments of India Mark II Hand Pump, Deepwell /India Mark III hand pumps(VLOM)
and extra Deepwell Hand pumps have been amalgamated in IS 15500 (Parts 1 to 8) : 2004:
IS 9301:1990 Deepwell handpumps – Specification (third revision)
IS 13056:1991 Deepwell handpumps (VLOM)– Specification
IS 13287:1992 Extra Deepwell handpumps– Specification
IS 14101:1994 Deepwell handpumps – Components- Cast Iron– Specification
IS 14102:1994 Deepwell handpumps – Components- Leaded tin bronze– Specification
IS 14103:1994 Deepwell handpumps – Components- Mild Steel– Specification
IS 14104:1994 Deepwell handpumps – Components- Nitrile rubber– Specification
IS 14105:1994 Deepwell handpumps – Components- Stainless steel– Specification
IS 14107:1999 Special tools for Deepwell handpumps –Specification
In Fig.-1 (Drawing) typical details of Deepwell Hand Pump as per Indian Standard are
illustrated.
4.2.3 Springs :
The springs are also a technology option for rural water supply but are found in hilly areas
of Gurdaspur district only. Springs occur due to the emergence of base flow as ground water to
the surface. Springs may be either perennial or intermittent. The discharge of a spring depends on
the nature and size of catchment, recharge and leakage through the sub surface. Their usefulness
as source of water supply depends on the discharge and its variability during the year. To select
the spring as source of water supply , it is necessary to ensure its dependability by measurement
of flow, local enquiry and study of catchment area, rainfall in the area. Suitable intake and
collection structures are to be planned to meet the requirement of the scheme. Normally, the
springs occur at elevated locations and hence the supply to the community can be by gravity
avoiding pumps.
4.2.4 Percolation Wells : It is large diameter dug up well adopted generally in Kandi Area nearer
rivers of Perinial source. Where static water level is not so deep ie in the range 10 to 15 meter
and there are no chances of contamination . It is dug up manually and its diameter is in the range
of 5- 8 meter depending upon the requirement water
The percussion method, often referred to as cable tool method, is one of the oldest, most versatile
and simplest drilling methods. A string of tools suspended on a cable is given up and down spud-
ding motion either manually of by power. The string of tools, in ascending order, consists of a
bit, a drill stem, drilling jars and a swivel socket which is attached to the cable. The bit strikes the
bottom of the hole, crushing, breaking and mixing the cuttings. Above the water table or in
28
otherwise dry formations, water is added to dissolve the cuttings which are lifted out by means of
a bailer. This method is most suitable for drilling in stratum where large boulders are encountered
in abundance at different depths.
4.3.2 Direct Circulation Drilling :
The rotary rig drills by mechanical rotation of a drill bit at the bottom of a string of drill pipe. The
typical string consists of a bit which scrapes, grinds, fractures or otherwise breaks the formation
drilled; a drill collar of heavy walled pipe to maintain a straight hole; and a drill pipe which
extends to the surface and imparts rotation to the bit. As the bit is turned drilling fluid (usually
bentonite mixed with other suitable material) is circulated under - pressure which" lubricates and
cools the bit, carries the cuttings in suspension to the surface, and plasters the wall of the hole to
prevent caving in.
4.3.7 Classification :
Based on diameter of hole, depth of hole and the size of drill rod used, the drilling rigs shall be
classified into light medium and heavy duty as specified in Table 4.1.
The tool weight at the surface for percussion (cable tool) type of drilling rig of light,
medium and heavy classes shall be 1135 kg, 1735 kg and 2 315 kg respectively.
4.3.8 Selection :
Based on the formation to be encountered during drilling, the diameter and depth of the boreholel
well, the recommended class of drilling equipment and the size of drill rod to be selected for
drilling is given in SP (QAWSM) 56 1994
29
Table 4.1. Classification of Drilling Rigs
(Clause 5.1)
Type of Drilling Classification Dia of bore Depth of Bore Size of
Hole Hole Drill Rods
mm m mm
(1) (2) (3) (4) (5)
30
i) Consolidated 114 Up to 50 DTH Light 76
Formations
like hard sandstone, 150 up to 170 DTH Medi um 114
lime-
stone, Trap, Basalt, 150 above 170 DTH Heavy 114
Quartzite, Granite, etc. 200 above 170 DTH Heavy 114
ii) Semi-
consolidated
formations:
a) Sandstone, Clay, 200 up to 250 Rotary - Circulation Light 73
Shale Direct
200 up to 450 Rotary- Circulation Medium 89
Direct
200 up to 450 Rotary- Circulation Heavy 89,101,114
Direct
b) Bouldery 200 up to 170 Percussion (Cable tool) Medium
200 above 170 Percussion (Cable tool) Heavy
iii) Semi-consolidated 150 up to 300 Rotary -cum -Percussion Heavy 89
And
Bouldery Formation
iv) Unconsolidated 200 up to 250 Rotary - Direct- Light 73
Circulation
formation up to 450 Rotary Direct- Medium 89
Circulation
above 450 Rotary - Direct- Heavy 89
Circulation
I v) Soft alluvial, clay, 500 up to 170 Rotary -Reverse-Circulation Light 150
gravel small (upto 125 675 above 170 Rotary - Reverse - Medium 150
Circulation
mm size) cobbles
formation
31
Seamless tube + 20 percent
Welded tube - 12.5 percent
Up to and including + 15 percent
406.4 mm outside - 12.5 percent
diameter
Over 406.4 outside + 15 percent
Diameter - 10 percent
c) Mass - No single tube shall deviate from the mass specified in table 4.2 mentioned below
with a tolerance of +10 .5 percent.
Table 4.2 : Dimensions and Masses of Screwed and Socketed casing pipes
Nominal Dia OutSide Thickness Mass of Socket Overall
Bore Diameter or Pipe Plain Tube Outside Length
or Pipe or Pipe Diameter Of Socket, Min
(mm) (mm) (mm) kg/m (mm) (mm)
(1) (2) (3) (4) (5) (6)
100 114.3 5.4 14.5 130.0 114.3
125 141.3 5.4 18.1 157.0 120.6
7.1 23.5
150 168.3 5.4 21.6 184.0 127.0
7.1 28.2
175 193.7 6.4 29.6 211.6 152.4
8.0 36.6
200 219.1 6.4 33.6 237.0 152.4
8.0 41.6
225 244.5 7.1 41.6 262.5 165.1
9.0 52.3 .
250 273.1 8.0. 52.3 291.0 177.8
10.0 64.9
300 323.9 8.0 62.3 346.0 177.8
10.0 77.4
4.4.1Coating of Tubes :
Unless otherwise specified by the purchaser, the tubes shall be externally coated with bituminous
solution or any other protective anticorrosion coating. The bituminous solution shall be of a
quality such as to produce a coating which, when dry, shall be smooth, tough and tenacious and
sufficiently hard not to flow on exposure to a temperature of 63°C and shall not be brittle at O°C.
It shall not be such as will impart a taste to the water.
Well screens serve as intake section of a well that allows water to flow freely into the well,
prevents sand from entering with water .and acts as a structural retainer to support the borehole in
unconsolidated material. To accomplish fully its intended purposes, the well screen must be of
efficient design i.e. it should let ample quantity of sand-free water to flow into the well with
minimum loss of head. The screens may range from pipes perforated in place to carefully
fabricated cage-type wire wound screens with accurately sized slot openings.
4.4.2 Types
The following are the various. types of well screens and slotted pipes:
Plain Slotted Pipes - These are pipes with slots cut by milling.
Bridge Slotted Pipes - The slots here are not cut but pressed out.
32
Mesh Wrapped Screens - These are made by wrapping copper mesh over perforated steel pipe
using spacers about 3 mm thick in between the copper mesh and the perforated pipe.
Cage Type Wire-wound Screens - These are special type of screens wherein a continuous
trapezodial or circular wire is spirally wound around a fabricated cage. The screen consists of
wedge profile wire of various dimensions, resistance welded to a cylindrical body made of
various members and cross sections of longitudinally arranged metal rods, which are in turn
welded into cylindrical ring couplings at either end.
4.4.3 Material :
The well screens and slotted pipes shall be made of either corrosion resistant material or steel
pipes having sufficient thickness to guard against the effect of corrosion and to ensure reasonable
life of tubewell. The following are the recommended materials for various type of well screens
and slotted pipes:
Low carbon steel or mild steel;
Stainless steel
Normally Stainless steel strainer is to be used and Low carbon strainer is to be adopted in case
steel strainer is not commercially available. How ever for rural areas the required diameter of
strainer is in the range of 150 mm to 250 mm and for these sizes stainless steel strainer is
easily available in the market .
33
4.5.3 Slot Size :
The shape and size of the slots shall be such that the gravel or acquifer material is not allowed to
block the open spaces. Based on the sieve analysis of the acquifer material, the size of the slot
openings shall be determined in such a way that finer fractions remain outside the slots. the slots
shall not be too wide to cause entry of the gravel and resulting in plugging. Sharp edges on the
periphery of the pipe may offer resistance to flow and hence it is preferable to have smooth
rounded edges.
The slot size for gravel pack shall be so selected as to retain at least 90 percent of the pack
material. However, in case the well is not provided with gravel pack, slot size shall be such that it
allows 40 to 60 percent of the aquifer material to pass through. The normal slot sizes shall be 1.0,
1.6 and 3.2 mm.
Percentage Openings
The percentage slot openings shall be such that the screen length provides sufficient inlet area to
limit the entrance velocity to 0.03 m/s.
Depth of
Thickness for Pipe Size (OD) in mm
Well
m 166.6 219.1 273.00 323.80 355.00
to
168.3
50 4.85 7.04 7.09 8.38 9.52
100 5.4 7.04 7.09 8.38 9.52
125 5.4 7.04 7.8 8.38 9.52
150 5.4 7.04 7.8 8.38 9.52
175 5.4 7.04 7.8 8.38 9.52
200 5.4 7.04 7.8 8.38 9.52
250 7.11 8.18 9.27 9.52 9.52
275 7.11 8.18 9.27 9.52 9.52
300 7.11 8.18 9.27 9.52 9.52
34
For obtaining a minimum of 15 percent open area, the screen aperture shall not be less
than 0.375 mm. The number and cross-section of the vertical support rods and the profile of the
wrapping wire shall be such as to give sufficient axial and collapse -strength (see Fig.
4).
35
4.6 Guidelines For Selection Of Slot Size
4.6.1 Determination of Slot Size:
The size of slot openings suitable for different formations shall be based on sieve analysis of
the aquifer material. Following procedure- and design criterion is laid down for general guidance:
A weighed quantity of the thoroughly mixed sample is passed through a set of Indian Standard
sieves from No. 75 onwards. The sieves are arranged such that the coarsest sieve is placed at the
top and the finest at the bottom. After proper shaking, the sieve set is opened and material retained
on each sieve is correctly weighed. The cumulative weight passing through each sieve is plotted
on semilogarithmic graph paper having percentage weight as ordinate on arithmatic scale and size
of the sieve opening as abscissa on logarithmic scale. A smooth graph is then drawn through the
points based on which selection of slot size shall be done.
Gravel Sizes
The gravel sizes shall be as given in Table. 4.5.
Table 4.5 Gravel Sizes
Sl. No. Grade Pack Practical Size Range IS Sieves
(see IS 460 (part 2) : 1985)
(mm)
1. A Fine gravel Over 2.0 to 3.35 2.0, 3.35
2. B Fine gravel Over 3.35 to 4.75 3.35, 4.75
3. C Medium gravel Over 4.75 to 6.3 4.75, 6.3
4. D Medium gravel Over 6.3 to 8.0 6.3, 8.0
5. E Coarse gravel Over 8.0 to 12.5 8.0. 12.5
36
To avoid trouble in placing and inspective of gradation, packs should not contain particles greater
than 13 mm.
4.7.2Particle Size Distribution :
The particle size distribution of gravel shall be determined by screening through standard sieves
in accordance with IS 460 (Part 2): 1985. The percentage distribution of the sizes shall be deter-
mined from a graph in which the percentage of material passing through each sieve is plotted
against the standard aperture of that sieve. Any size, say D20 will thus indicate that the
cumulative weight of all the grains smaller than this size is 20 percent of the total weight of the
test sample.
The uniformity coefficient of the gravel, that is, the ratio of its D60 to D10 sizes shall not
exceed 2. A material with uniformity coefficient less than „2 shall be classified as uniform and if
greater than 2 it shall be taken as non-uniform.
4.7.3Pack Aquifer Ratio :
The pack aquifer ratio (PIA ratio) is defined as the ratio of 50 percent size D50 of the gravel pack
to the 50 percent size of the aquifer. The size of gravel when used as pack in tubewells shall be
decided in accordance with the size of the aquifer material proposed to be tapped. The gravel size,
based on minimum head loss through gravel pack and minimum sand movement, shall be limited
as below:
a. Uniform aquifer with uniform gravel pack:
b. Pack aquifer ratio shall be 9 to 12.5
c. Non-uniform aquifer with uniform gravel pack:
d. Pack aquifer ratio shall be 11 to 15.5
4.7.4 Thickness :
The thickness of gravel pack shall be limited to 13 to 18 cm. The size of the screen slot
opening is governed, among other factors, by the size of the gravel or aquifer material which it
has to retain. The slot size for gravel packed wells should be such that it retains about 90 percent
of the gravel.
The development of a well is its treatment for the purpose of establishing the maximum rate of us-
able water by cleaning the produced water of turbidity, sand, sediment or other impurities intro-
duced during drilling.
4.8 Methods of Development
There are numerous methods of development.
and an important factor in all these is that the development work be started slowly and gently
and increased in vigour as the well is developed. The development should be started as far as
possible from the bottom of the screen because with this compaction takes place as the work
progresses upward and the overlying material can move downwards. The known methods of
development are described below:
4.8.1 Over pumping:
Over pumping means pumping the well at a higher rate than it will be pumped when it is put in
service. It may be simpler to over pump in small wells or poor aquifers by employing the
pumping equipment intended for regular use in the well.
4.8.2 Compressed Air :
Another popular way of development is by using compressed air but it requires considerable
equipment and skill on the part of the operator. The capacity of compressor should be at least 9.35
cum per minute (330 cfm) at 250 PSI pressure for depth up to 200 meter . In case depth of bore
37
well is more than 200 mt a proportionately higher capacity compressor shall be used
4.8.3 Calculation of Discharge : Discharge of Tube well shall be determined by using V-notch .
Tables indicating discharge for various V-notch readings has been placed at Annexure –N. After
completion of the testing of tubewell information should be supplied as in Form B.
4.9 Verrticality and Alignment
If a turbine well pump is to be installed in a well, the well should be true to line from its top to a
point just below the maximum depth at which it is proposed to set the pump. A tubewell out of
alignment and containing kinks and bends or cork-screws should be rejected because such
deviations cause severe wear on the pump shaft bearings and discharge casing and in a severe
case, might make it impossible to get a pump in or out. If an air-lift or a suction pump is used for
pumping. Alignment is not so important and the same is applicable to the submersible type of
pump.
4.9.1 The conditions that cause wells to be out of plumb are :
a) the character of the sub-surface material penetrated during drilling,
b) the trueness of the pipe used as well casing, and
c) The pull-down force on the drill pipe during rotary drilling.
While drilling, gravity tends to make the drilling bit cut a vertical drill hole. Varying hardness of
the materials being penetrated. however. deflects the bit from a truly vertical course;
d) Improper leveling of the Rig before the drilling is started
4.9.2 The measurements made are of the plumbness and straightness of the cased bore. Thus. an
oversized hole may be out of plumb but the casing may fall within specified limits. The casing
should not be permitted to excessively encroached the annulus and hinder placement of grout or
gravel pack
4.9.3 In case of gravel-shrouded tubewells, if the pipe assembly is found inclined in a slant
position before completing the gravel pack, the assembly should be pulled in a desired direction
by suitable methods with a view to rectify slantness and bringing the pipe assembly within the
'permissible limits of verticality. The gravel pack should be completed immediately after the
verticality has been tested and rectified.
4.9.4 The verticality of the tubewell shall be tested by using plumb or plunger E (see Fig. Clause
4.9.4 ) 6 mm smaller in diameter within the inside diameter of the well casing. The plumb may be
made from a piece of sheet steel or a short piece of pipe. Which-.ever is used, it shall be heavy
enough to keep the plumb line taut. The hub of the ring shall not be solid, as the water shall pass
through it as it is lowered in the well. The bore F from which the plumb line A passes shall be in
the exact centre of the ring. Knots or marks shall be made every 3 m on the plumb line to indicate
the depth to which the ring has been lowered in the well. The plumb shall be suspended from the
guide pulley where it shall be at least 3 m above the top of the well. The guide pulley is fixed on a
tripod or frame. B as shown in the figure. The vertical centre of the pulley shall be so located that
the plumb line A comes off its outer edge exactly over the centre D of the well casing. The results
shall be recorded in Form A.
4.9.5 For tubewells encased with pipes up to 350 mm diameter, the verticality of the tubewell
shall be measured in terms of clear cylindrical space available within the housing pipe after the
construction of the tubewell.
4.9.5.1 Vertica1ity of .the tubewell may have a deviation so as to provide clear cylindrical space
not less than the clear cylindrical space available in a hypothetical tubewell of the same size but
having deviation of 10 cm per 30 m in one direction and in one plane only.
4.9.5.2 The verticality of tube well is to be tested as given in 4.9.4 After the necessary
computation is made, cross sections of housing pipes at different depths are drawn on a graph and
38
clear cylindrical space is, determined. The cylindrical space of the actual~ constructed tubewell
shall be referred to as 'G' in the following paragraphs.
Cross sections of hypothetical tubewell identical in dimensions to the actual tubewell but having
deviation of 10 cm per 30 m in one direction and in one plane are drawn on the graph sheet and
the minimum allowable cylindrical space 'H' is determined.
4.9.5.3 If cylindrical space 'G' of the actually constructed tubewell is equal or more than the
cylindrical space 'H' of the hypothetical tubewell (having deviation 10 cm in 30 m in one direction
and one plane), the tubewell actually constructed shall be considered within the permissible limits
of verticality.
4.9.5.4 As an example, cross sections of two tubewells Gl and G2 having 300 mm diameter of
housing pipe have been drawn after computation of verticality results in Fig. G1 and Fig. G2
while Fig. G3 shows the cylindrical space H of hypothetical
39
Fig.G1
Fig. G2
40
Fig. G3- H
A Normal Test
SL Rated Depression Specific Total Sand in Static Pumping
No. Discharge at Rated Yield Hours ppm at End Water Water
(m/s) Discharge Run Of Test Level Level
(m) (h) (m) (m)
__________________________________________________________________
(1) (2) (3) (4) (5) (6) (7) (8)
41
4.10 Maintenance of Tube Wells :
Wells, like all other engineering structures, need regular, routine maintenance in the interest of a
continuous high level of performance and a maximum useful life. The maintenance of wells and
pumps is often neglected, since the greater portion of both the well and the pump are located
beneath the ground surface. The nature of deterioration which occurs in a well may not be readily
discernible during operation and may not be recognized until the well fails. The deterioration
42
usually develops slowly to a critical point and then accelerates rapidly to failure. Therefore, any
neglect of well maintenance often results in the complete loss of the well.
4.10.1 Factors Affecting Well Performance
Several factors initiate well losses in inefficient wells. Care should be taken to
differentiate between those factors associated with the normal wearing of pump parts and those
directly associated with changing conditions in and around well. A well may show a reduced yield
because of reduction in the capacity of the pump due to excessively worn parts. On the other
hand, the excessive wearing of pump parts may be due to the pumping of. sand entering the well
through a corroded screen. It is also possible for corrosion to affect only the pump, reducing its
capacity but to have little or no effect on a properly designed well.
The common reasons of decrease in yield of a well include: (a) losses caused by reduction
in permeability from mud invasion or by compaction and shearing of the formation face during
drilling, and (b) losses from the turbulent flow of water adjacent to the well through the screen or
well face and inside the casing to the pump intake.
4.11 Preventive Design Features
High well losses are unnecessary since they can be minimized by a good well design and
construction. Therefore water well maintenance procedures begin with the techniques
implemented during the drilling of the original well and continue with the type of materials used
and with the extent of care, or the lack of it, that the well is given over the months and years of
operation.
Critical well design feature is the entrance velocity through the screen. An ideal entrance
velocity is 1.5 to 3.8 cm/s depending upon the average permeability. Maintaining low entrance
velocity results in high efficiency, minimizing sand pumping and reducing the rate of corrosion
and incrustation in well. The distribution and shape of slot openings is as important as the
entrance velocity in influencing well efficiency
3.3 A comprehensive design of the well system includes certain features in the discharge and
distribution facilities to permit proper monitoring. and maintenance of the well and pump. The
more important of these features are:
a) provision of an outlet in the discharge system to permit diversion from the system during future
test pumping and water sample collection,
b) a permanent throttling valve on the discharge,
c) a permanent airline with valve and gauge for water level reading,
d) access into the pump chamber casing which can also be used to measure water
levels to permit back up water level reading by tape or electric probe, and
e) ready access to the well to pull the pump and maintain the well.
4.12 Maintenance Planning
The planning of well maintenance procedures should be based on a system of good record
keeping. The problems that result in reduced well yield occur at and around the well screen and
are very much out of sight. The analysis of good records must, therefore, be relied upon for
detection of problems in the well.
Among the records kept should be pumping rates, draw-down, total hours of operation,
power consumption and water quality analysis. Pumping rates and drawdown are particularly
useful in determining the specific yield which is the best indicator of existing problems in a well.
The specific yields of wells should be checked periodically and compared with previous values to
determine if any significant reduction has taken place. Such a reduction is often due to clogging of
43
well screen and formation around it by incrustation.
Power consumption records also provide valuable evidence of existence of problems in
wells. An increase in power consumption, not accompanied by a corresponding increase in the
quantity of water pumped, indicates problem in either the pump or the well. If an investigation
shows no problems in the pump nor appreciable increase in the dynamic head against which the
pump is operating, then it is most likely that a problem exists in the well and the problem is
causing an increased draw down. A check on draw down should then be undertaken and the well
checked for incrustation
Regular chemical analyses of water will indicate the type of incrustation that might occur
and the expected rate of deposition in the well and its vicinity. The quality of water in some wells
changes slowly with time and only a regular analysis would detect such changes
In wells, the waters of which have a high incrustation potential, the frequency of
observations of all types should be as high as possible and consistent with the use to which water
is being put. Observations should be much more frequent in wells serving a community
4.12.1 Interpretation of observed or Measured Changes in Well Performance or Conditions
:
A decrease in specific yield without a proportional decline in the static water level may indicate
blockage of the screen by accumulated sediment in the bottom of the well, blockage of the screen
or gravel pack by incrustation, or collapse of casing or screen
Should the specific yield during a test for yield and draw-down show a decline of 10 percent or
more from the original test at a given discharge, the well should be surveyed to determine the
location and extent of possible contributing conditions. If collapse appears to be the problem, the
well should be surveyed to determine the location and nature of the collapse. If Collapse is not the
problem, the inside of the well should be scraped and the pertinent that was subsequently bailed
from the bottom should be examined to determine the chemical composition, nature and extent of
the encrusting material as a basis for a plan of rehabilitation
An increase in the sand content of the discharge, particularly if it is associated with a measurable
accumulation of sand in the bottom of the well, may indicate enlargement of slot sizes by
corrosion; settlement of gravel pack beneath a bridge leaving an unpacked zone opposite a
screened section; a break in the casing or screen, usually at a joint; or failure of a packer seal.
Mechanical and mineralogical examination of a sample bailed from the bottom of the hole and
comparison with the original description of the aquifer and gravel pack materials made during
construction of the well may give some indication of the nature of the difficulty. If the material is
noticeably smaller in grain size than the grain size of any aquifer screened in the well, or if the
material contains the full range of sizes of the gravel pack, there is probably a break' in the casing
or screen. If all the material is smaller than the screen slot sizes, it is probably a bridge. If the
above interpretations of grain size and distribution are not applicable, the problem may be due to
enlargement of a slot size by corrosion. If the problem is apparently due to bridging, it can
frequently be corrected by redevelopment while pouring water down the gravel refill trernies and
the addition of gravel pack material. The other problems usually require a photographic survey to
be made of the well to more clearly assess the problem. Decisions can then be made concerning
the practicability of rehabilitation and the procedures to be followed.
Settlement of the land surface around a well, the development on the ground surface of
small drainage channels towards the well, and cracking and settlement of pump pads and
foundations are all indicative of settlement of the well structure. In some areas, the problem may
be associated with land subsidence due to excessive pumping of the aquifers. Usually, however,
the problem is related to poor well design, construction, or development, and results from
44
excessive pumping of sand. In many instances, the sand pumping is complicated by collapse of
casing or screen, bridging of gravel packs, and similar deterioration. When such conditions are
encountered, the well should be taken out of service, sounded for depth, and surveyed
photographically to determine whether any structural damage has occurred. If the well cannot be
shut down because of the need for water, the casing should be temporarily supported by welding
heavy I-beams to it.
Decline in pump discharge and head may be due to deterioration of pump or simultaneous
deterioration of both the well and the pump. A common occurrence is a decrease in shut-in head
and significant decrease in discharge without a corresponding decline in static water level and
specific yield. Such an occurrence is usually due to one of the following conditions: (1) improper
adjustment of the impeller due to wear or other causes, (2) a hole in the column pipe, or (3)
erosion of the impeller or bowls.
A condition which is usually associated with considerable vibration when the pump is running. If
the condition cannot be corrected by adjusting the impellers, the pump should be pulled and
repaired or replaced. The cause of the problem should be thoroughly investigated and made a part
of the permanent well and pump record
Excessive vibration of the pump may result from imbalance of the impeller or from the
pump being installed in a crooked well. A pump which makes a crackling noise similar to gravel
being thrown on a tin roof is probably experiencing cavitations at the impellers. This is
particularly true if the discharge is surging and irregular and contains considerable air. The
condition usually results from a decline in the static water level or reduced well capacity because
of incrustation or accumulation of sand in the screen. Either of these conditions results in
excessive draw down for pump and a decline below that required in the available net positive
suction head. If the condition is due to a decline in the static water level, it can usually be
corrected by lowering the bowl assembly . In severe cases, it may be necessary to add additional
stages and a larger motor in addition to lowering the bowls. The well should also be checked for
possible incrustation of the screen or other causes of reduced efficiency.
Excessive heating of the motor is occasionally encountered and is usually associated with an
overload condition and the consumption of excessive electrical energy. Such heating may be
caused by a poorly adjusted impeller which is dragging on the bowls, too tight a packing gland,
improper or unbalanced voltage, poor electrical connections, or improper sizing of motor.
Occasionally, an inadequate discharge will be associated with trash that has lodged in the bowls
or blockage of the impellers or bowl channels by products of corrosion and incrustation.
Correction entails pulling the pump for repair. These conditions may also be reflected in
overheating of the motor. Where overheating is encountered, the installation should be first
checked by an electrician to determine whether the trouble is in the power system or in the pump,
rather than in the well.
Occasionally, a noticeable increase in oil consumption is encountered in oil-lubricated
pumps. The excessive consumption may be due to a hole in the wall of the oil tubing or excessive
wear on a packing gland in the tubing. These conditions can result in a decrease in differential
pressure in the oil tubing and loss of oil into the well. The first condition can result in inflow of
water into the tubing and formation of an emulsion of water and oil. The emulsion lacks adequate
qualities and can result in excessive wear or burning out of the bearings. The escape of oil into the
well can result in the accumulation of oil floating on the water surface in the casing. With
adequate pump submergence, this latter condition may not cause serious trouble but if draw-down
increases due to a decline in water table or deterioration of the well, oil may be drawn into the
pump. causing impairment of water quality. In addition, the presence of oil may contaminate the
45
groundwater and preclude accurate measurement of static water and pumping water levels.
Small capacity wells usually have discharges of less than 500 Lt/min. casing and screen
used for such wells commonly are 15 cm in diameter or smaller, and materials used in their
construction are relatively light in weight. While the observations and measurements outlined
above are equally applicable for large capacity pumps and wells they are usually difficult to
justify economically.
Maximum Safe yield and specific yield
Maximum safe yield of the well is the quantity that can be drawn without continuous
lowering of the water table and without “sand blowing” indicated by soil particles appearing in
pumped water. The specific capacity of a well is the discharge per meter of draw down at the
well. Design yield of Tube Well shall be taken after incorporating the decline in the yield of the
well during its design life of 15 years . It is observed that over a period of time yield of Tube well
decreases . Safe yield of Tube Well should be t 30% more than the required design discharge to
cover the decreases in yield over a period of time for Natural Packed Tube wells and 50% more
for Gravel packed Tube Wells. Sample calculation to determine yield of Tube well are placed at
annexure –M
The rehabilitation of well means repair of wells which have failed because of collapse, broken
casing and screen or other similar damage, and the treatment of wells which have begun to pump
sand, have experienced a change of water quality or have shown a marked decrease in discharge
and efficiency because of incrustation, or other factors which tend to reduce the intake area of the
screen and permeability of the adjacent aquifer. It shall be undertaken when the specific yield
falls to about 80 percent of the initial value.
The cause and extent of well sickness must be diagnosed before the rehabilitation
programme is undertaken.
If the decrease in yield is due to the lowering of water table in the aquifer as a result of
over pumping or interference from other wells, then nothing can be done.
However the failures due to incrustation, corrosion, improper design, gravel placement
and faulty construction may be remedied by a suitable rehabilitation programme.
The major problem in rehabilitation is estimating the exact nature of the deterioration
since the screen and other components most likely to deteriorate are not open to usual
inspection or testing. This may be overcome to an extent by adequate investigation and
planning prior to undertaking the work as given below.
Information to be given by user
The following information shall be made available by the owner:
a) Initial and present well yield, depression, and water level as observed
periodically during the well's service life;
b) Sand content in ppm, if any;
c) Grain size distribution of the strata tapped as a result of sieve analysis:
d) Location of screen, its opening size, percentage of screen surface area to
the total open area, screen material, length and diameter of screen and well
pipes, etc, and data of acceptance of the well;
e) Size and quantity of pea-gravel used initially and during its service life;
f) Method used and details of development with results;
g) Method of drilling adopted, name of drilling agency, original pump and well test results
46
and results of subsequent tests, if available;
h) Results of the initial and present chemical analysis of the well water;
i) Details of any chemical treatment, if ever given to the well and results achieved
therefrom;
j) Sounding of the well observed every year
k) Details of repairs to the pumping equipment carried out every year; and
l) Number of electricity units consumed per kilowatt ratings every year during service life
of the well.
Investigations to be carried out by the contractor
The following data shall be determined for reference when starting rehabilitation of any well:
a) Date of acceptance of well;
b) Name of contractor;
c) Method of drilling;
d) Method of formation sampling;
e) Formation log;
f) Mechanical analyses of aquifer samples;
g) Mechanical analyses of pack material;
h) Screen materials, slot sizes, diameter and depth of setting;
i) Present open area of screen, design inflow velocity;
j) Depth, diameter and material of pump chamber;
k) Method and completeness of development;
l) Original pump and well test results and result of subsequent tests with dates;
1) Static water level
2) Measured depth of bottom of hole
3) Discharge
4) Draw down
5) Specific yield
6) Step tests
7) Production tests
m) Ground water hydro graphs of the area;
n) Quality of water analyses of well with dates; and
o) Resume of maintenance, rehabilitation and performance.
The following investigations shall be carried out and data determined before starting
rehabilitation on any well :
a) Chemical and bacteriological analysis of the well water shall be carried out and compared with
the original one, with regard to its original and the present apparent incrustation potential. If it is
high or has increased with time, treatment may be required;
b) If the well is yielding sand, the discharged sand sample shall be collected and compared with
the original formation log so as to locate precisely the position of the possible rupture or loose
connection, etc;
c) If equipment is available, an underwater photographic survey shall be carried out and location
of any evidence of incrustation, organic growth or accumulation on the casing and screen
recorded. Also, any filamentous algae, iron bacteria or. Similar organisms floating in the water
shall be noted. Any evidence of mechanical damage to the casing and screen shall be carefully
inspected with the
camera and recorded with regard to ' its description and depth;
d) The present specific yield at design discharge rate and draw down, low enough to permit
47
continuous pumping for 4 hours, without breaking suction, shall be determined. This will give a
qualitative measure of the degree of deterioration and by comparison with the later tests, the
success of rehabilitation programme
e) The pump shall be pulled out and various parts examined immediately as they are removed
from the well. The column pipe, drive shaft, bearing spiders and bowl shall be inspected for
evidence of excessive accumulations or deposits of ferric or ferrous hydroxides. If the deposits are
present, sufficient samples shall be collected to fully fill a bottle capable of being sealed airtight.
This shall be done as rapidly as possible and the samples sent to the laboratory immediately, so as
to avoid generation of heat in the sample. The samples shall be sent to the chemical and biological
laboratories for identification of chemical compounds present and identification, if possible, of
organism involved; ,
f) The pump parts shall be examined for evidence of pitting, tuberculations, graphitization,
cavitation and wear. Pump bowls and impellers shall be inspected for evidence for graphitization
in areas where sulphate-bacteria are known or suspected to be present; and
g) The static\ water level and depth of the bottom of the well assembly shall be
checked when the pump is taken out of the well.
Acid treatment using hydrochloric (muriatic) or sulfamic (H2NS02H) acid is commonly
employed for rehabilitation. It efficiently eliminates incrustation due to calcium, magnesium and
iron carbonates', or iron hydroxides which can be detected by examining the scrapings from the
inside of the screen for chemical composition.
The strongest grade of muriatic acid, designated the '27.92 percent hydrochloric acid, is used in
full strength for acidizing. The amount of acid added for a single treatment is 1.5 to 2 times the
volume of water in the casing, screen and gravel pack between the bottom of the well and 3 m
above the topmost screen slot. It is poured through a black iron or plastic pipe 38 to 50 mm in
diameter and long enough to reach the bottom of the well. Acid to fill 1.5 to 3 m of screen is
poured first; the conductor pipe raised about 1.5 to 3 m to pour more acid and the process is
continued till all the acid has been added to the well. The acid, being heavier than water, displaces
it as it is poured.
Iron and manganese hydroxides and oxides, although soluble in hydrochloric' acid, precipitate out
if pH is above 3. To keep iron in solution, regardless of pH so that it can be pumped from the well
with spent acid, a chelating agent like Rochelle salt, citric acid, tartaric acid, phosphoric acid or
glycolic acid may be added to the acid. About 900 g of chelating agent may be used for 45 1 of
hydrochloric acid.
To curb the tendency of the acid to attack metallic casing and screen, either inhibited acid or an
inhibitor such as knox gelatine should be used. 2.3 to 2.7 kg gelatine dissolved in warm water and
added to 450 Lt of acid serves the purpose. The acid is left in the welI for about 4 to 6 hours. At
the end of about 3 min, sufficient water is added to displace the acid from 3 m above the topmost
slot to the bottom of the well. While the acid is in the well, it is surged by air or with surge block
for 15-20 minutes each hour. The acid is bailed out at the end of about 6 hours.
Hydrochloric acid is dangerous to use unless handled by experienced personnel and suitable
equipment. It gives off poisonous fumes and its reaction with carbonates is some times violent
spraying around the well. The transport of liquid hydrochloric acid to the field is also not easy.
Hydrochloric acid of adequate strength is readily available at a relatively low price. It has been
used observing safety precautions and no injuries or casualties have resulted. Under the
circumstances, if appears that hydrochloric acid, despite the danger and difficulties associated
with its use, will continue to be used. However, if trained and experienced crew are not available
to carry on the acidizing work, consideration shall be given to employing the less dangerous
48
sulfamic acid.
It is for these reasons that sulfamic acid is being' increasingly used for well rehabilitation. it is
more expensive than hydrochloric acid but less aggressive and safer to use and easily shipped and
stored as dry crystal or powder. Its corrosive effect on well screens and pumping equipment is
markedly less. It, however, requires about twice as long to treat a well as does hydrochloric acid.
When using sulfamic acid in a well, the same estimates are made regarding the column of water in
the well to be displaced and 1.5 to 2 times that volume is poured into the well through a black iron
or plastic pipe as described earlier. It is, available in granular form and may be poured into the
well from the top.
Because sulfamic acid is a milder and less aggressive acid, it is mixed in a black iron or wooden
tank at the surface. A tank about 1.2 x 15 x 3 m is usually adequate and holds about 5360 lt. The
tank shall have a bottom valve through which the acid solution is drawn into the well. 41 kg
sulfamic acid, 450 g of phuonic F68 and 2.7 kg chelating agent such as Rochelle salt, citric acid,
tartaric acid, etc, are added and dissolved in each 450 l of
water to be poured into the well. If well is screened with metal, an inhibitor' such as knox gelatine
shall be used at th'~ rate of 1.8 to 2.3 kg per 450 litre of solution. The acid shall remain in the well
for at least 12 hours during which it shall be surged by air or surge block about 15 to 20 minutes
every hour. Then it is bailed or pumped to waste.
The spent acid is bailed or pumped out of the well using a corrosion-resistant pump for the
purpose. In many wells, pumping with a centrifugal pump is possible. Close observation of the
bailing or pumping discharge and the drawdowns during removal of the acid shall give an
indication of the success of the treatment.
During acid treatment of a well the crew shall wear protective clothing and respirators. One or
two 250 lt drums of concentrated sodium bicrabonate shall be available for quick neutralization of
acid with which crew members may come in contact during the operation.
During treatment, incrustation is dissolved and the fines incorporated 'in the agent remain in the
pack and base meterial. On completion of acidizing the well shall be redeveloped using
polyphosphate, sufficient chlorine for a shock treatment and one of the methods of surging or
jetting.
Glossy Phosphate Treatment
Glossy phosphates (polyphosphates) act by dispersing clays and salts and loosening their adhe-
sion to sand and gravel so that they may be readily pumped out of the well. Treatment with one
of the polyphosphates, coupled with vigorous agitation, effectively breaks up the incrusting
material and cleans the well. An important advantage is that polyphosphates are safe to handle.
The polyphosphates are usually used in conjunction with a wetting agent, sodium carbonate and
chlorine compound. The wetting agent facilitates the penetration of the polyphosphate solution
into the fine-grained material and hastens the operation. Sodium carbonate has a cleaning action
on rust on iron screens and pipes and also serves to neutralize the effects of oil and other organic
compounds that might interfere with the action of chlorine. chlorine acts as a catalyst and
apparently improves the action of the polyphosphates besides sterilizing the well and the adjacent
formations.
NOTE - Under of the fabric. Therefore, until more is known of the fabric and composition some
circumstances, the wetting agents
cause too rapid a breakdown of the aquifer, it is recommended that wetting agents be omitted
from the solutions.
In wells screened with fiberglass-reinforced epoxy, sodium carbonate may be left out of the
49
solution without any loss of efficiency.
The following procedure may be adopted for rehabilitation:
Estimate the volume of water in the pack and screen between the water table and the bottom of
the hole to the nearest 450 lt. On the basis of the following amount of reagents per 450 lt of water
in the well, estimate the amount of various chemicals required:
a) For fibre glass-reinforced epoxy screens - Sodium hexametaphosphate 3.6 kg;
b) For metal screens-In addition to the above 900 g sodium carbonate; and
c) Should experience show use of a wetting agent is helpful, 450 g pluronic F 68
or equivalent.
Most wells contain between 10,900 to 15,900 lt of water. A wooden or black iron tank 1.2 x 1.5 x
3 m is a convenient size for transportation, etc, and holds in excess of 5 360 I of water. Therefore,
two or three batches of solution mixed in the tank shall be required for each well. A convenient
but not necessary arrangement that speeds up the operation is to use two tanks in order that the
next batch of solution may be mixed while the previous one is being placed in the well.
The solution is poured or pumped into the well through a 38 or 50 mm plastic or black iron pipe
that initially is installed from the surface to about 1.5 m above the bottom of the well. Sufficient
solution is ,put in the well to displace an estimated 1.5 or 3 m of the water in the casing and pack.
The pipe is then raised 1.5 or 3 m and the procedure repeated until all water in the well and pack
are displaced by the solution. The solution has higher specific gravity than the water and
displaces it upward and outward from the well. When all the solution is installed in the well, a
volume of water equal to about one-half that contained in the casing and screen in poured" is at
the top to displace the solution from the screen and force it out into the formation (see Table 4.6).
A 200mm casing contains about 11 lt and 200 mm screen about 18 lt of water per metre of
length. A surge block bail or similar tool is then run from the bottom of the well to above the
water table two or three times of the inductor pipe for air surging may be replaced to near the
bottom of the well and air bubbled up through the well to thoroughly mix the solution remaining
in the casing screen.
Chlorine Treatment
Chlorine has been found effective in loosening clogging of the intake section of the well and
water-bearing formation caused by deposition of iron oxide. Chlorine, when added to water,
forms hypochlorous and hypochloric acids, which kill the bacteria and produce an effect of
'burning up' the organic slime.
Sufficient amount of calcium or sodium hypochlorite to give a concentration of 100 to 200 ppm of
free chlorine is added to the well either directly or in water solutions. Alternatively, chlorine gas
may be used but it is dangerous and requires experienced personnel and equipment which may not
always be available. It must be put into the well in a water solution as it is both corrosive and
toxic when inhaled. Hypochlorite solutions are cheaper, more convenient and safer to use than gas
but generally less effective.
50
The chlorine solution is introduced in the well through a small diameter plastic pipe. A quantity
11 to 18 kg added slowly over a period of 12 hours shall suffice for a large well. The pipe car-
rying chlorine must be positioned so that the solution does not impinge directly upon any part of
the pump, well casing, or well screen. After introduction, the chlorine solution is forced into the
water bearing formation by adding about 50 to 100 times the volume. of water standing in the
well.
The well shall be surged or the solution agitated vigorously as in acid treatment.
Repeated chlorine treatment will have more chance of flushing the clogged formation around the
well. Alternate acid and chlorine treatments are found to be even more effective.
Dry Ice Treatment
The use of dry ice, that is, solid carbon dioxide is still in the experimental stage. Dry ice changes
from solid to gaseous state rapidly with considerable pressure, when put into well water. The rap-
idly expanding gas is confined within the well casing and is forced through the screen openings to
loosen the clogged material. On account of high pressure developed, provision shall be made for
the control and relief of pressure to guard against any damage. As dry ice may cause severe burns,
if handled with bare hands, heavy gloves or tongs shall be used in handling the ice.
Explosives
These are sometimes employed to develop and enlarge crevices and fissures in tubewells drilled
in hard rocks. Charges of 30 to 500 kg are used according to the hardness of the rock and the
depth at which the charge is to be detonated.
Criteria for Acceptance
An increase in yield of the well by 20 percent of the pre-rehabilitated yield of the well or
attainment of 75 percent of the initial yield, whichever is more, shall be the basis of acceptance.
Alternatively; it may be agreed to between the contractor and the owner.
Information to be supplied by the contractor to Owner for future use
The Contractor shall supply the following in formation to the owner for future use:
a) Results of the investigations carried out before taking up rehabilitation;
b) Result of chemical tests carried. out before and after rehabilitation work;
51
c) Methods used along with name and quantity of chemicals used and number of
treatments given;
d) Results of rehabilitation; that is, discharge, depression and sand content in ppm
at start and after 20 minutes;
e) Sounding of the well after treatment;
f) Condition of the pumping unit before rehabilitation and details of repairs carried
'out to it;
g) Suggestions, based on investigations, for future upkeep and maintenance of the
well including recommended limit to continuous discharge and depression, that
is, rate of pumping in order to avoid harmful over pumping and thereby
limiting the entrance velocities; and
h) Any other relevant information desired by the owner.
WELL ABANDONMENT
Proper plugging of abandoned wells is a fundamental practice in the preservation of high ground-
water quality. Permanent sealing of abandoned wells is important because serious groundwater
pollution can occur from either contaminated surface water or interaquifer transfer of ground
water from a contaminated aquifer.
The basic concept in the proper sealing of an abandoned well is the restoration as far as possible
of the geologic conditions that existed before the well was drilled. The local geologic conditions
must be assessed in detail to determine the most effective method of well sealing. Sealing is
usually achieved by, grouting; when grouting below the water table, the cementing material
should be placed from the bottom up, by methods that would avoid segregation or excessive
dilution of the material. The upper portion of the casing should be removed to ensure intimate
contact of the grout with the wall of the hole to form a water-tight plug in the upper 5 to 7 m.
2.3 To seal an abandoned well properly, the type of groundwater occurrence must be considered.
Under water table conditions, the objective is to prevent percolation of the surface water through
the well or along the periphery of the casing to the water table. Under artesian conditions, the
sealing operations must confine the water to the aquifer in which it occurs.
52
The preferred technology option for treatment of surface water for rural communities is
plain sedimentation followed by balancing tank, slow sand filtration and disinfections (with
bleaching powder), pure water sump or filter water sump. Usually a jackwell is constructed in the
canal/ stream or river and water is pumped to the elevated storage reservoirs for distribution to the
villages thus resulting in higher power charges. In view of the treatment cost and higher power
charges and larger skilled manpower involved, user charger for supplying treated water from
streams and lakes are likely to be higher. Hence, the community is to be informed for the high
user charges and their willingness should be obtained for such surface schemes before selecting as
technology option.
Surface Schemes shall be designed only where the following conditions prevail :
53
CHAPTER 5
PRELIMINARY SCHEME REPORT
This chapter describes the preparation of Preliminary Scheme Report (PSR) for a rural water
supply scheme, which is essential to arrive at an economical technology option in consultation
with the rural community.
54
Alternatively rough cost estimates can also be prepared by using per capita cost
method . However line estimates will be more realistic .
7. O&M cost for the present population for water supply (including existing and
proposed), and small bore sewer (wherever proposed)
8. Schematic diagram of existing and proposed water supply schemes showing the
source, OHSR, transmission and distribution along with lengths and levels.
9. A village map showing the layout of the roads along with existing and proposed water
supply scheme showing the source OHSR, transmission and distribution and roads and
drains preferably using Total Station method.
5.1 Reconnaissance
A support Agency consisting of social scientist, consulting engineer & geologist and the
community shall go round the village for collecting the data required for preparation of the
PSR. During the reconnaissance, the functioning of the existing water supply scheme is
studied and the rehabilitation needs are noted. For the proposed scheme, the location of the
source and the location of OHSR have to be identified with the consent of the community.
The ground water availability and quality of water may be ascertained by studying the
water table in the existing sources and discussion with the community. The highest ground
level and the lowest ground level and lengths of various components of pipeline have to be
assessed. During the reconnaissance the nature of terrain and soil condition are noted and
alignment for the out fall drain leading to the disposal point is also identified and noted on
the map. At the end of the reconnaissance, the extent of rehabilitation and scope of the
proposed scheme along with the concept would have been formed.
After collecting the field data, approximate sizes are arrived at an approximate cost for
investment and O&M are worked out for various technology options for providing water supply,
sanitation and drains. Approximate rates for pipelines, water storage tanks, filtration units, ground
water recharging structures are considered while preparing the line estimates based on the
previous experience structures are considered while preparing the line estimates based on the
previous experience. Hence a near reasonable line estimate for capital cost and O & M cost can be
arrived at so that the Community knows its required contribution and likely O & M cost. After
which a PSR is prepared consisting of the executive summary, salient features, line estimates,
capital cost and O&M cost for various technology options, schematic sketches and village map.
The PSR will be presented to the community in a Gram Sabha, where various technology options
will be discussed and the community will choose the most suitable options which is affordable to
them (with respect to water supply and village sanitation). At the end of Gram Sabha, the land
required for the implementation of the scheme should also be identified and acquisition if
necessary shall be completed before detailed scheme report is to be done.
55
CHAPTER-6
DETAILED ENGINEERING FOR
A RURAL WATER SUPPLY SCHEME
This chapter contains the methodology adopted for detailed engineering for a rural water supply
scheme. Field survey, design calculations, detailed plans and estimates etc are described. The
preparation of detailed engineering commences only after approval of the PSR and therefore the
designs and estimates will be prepared for the chosen technology option only. The various
components of a rural water supply scheme based on surface source and groundwater source
are discussed here.
6.1 Surveys:
The first step in detailed engineering is a field survey to find the levels at source, at
OHSR/UGSR and along the road network. In addition, lengths and alignment (bends) shall be
recorded. If any village map is readily available it will be up dated. Usually methods of survey
applicable for villages are chain and compass survey, level survey, plane tabling and total station
survey. Possibility of using GIS base maps may also be explored.
6.1.1 Total station survey System (TSSS) :
It is a modern method, which provides accurate and fast field information on levels, distances,
angles and landmarks. The TSSS is a system that includes an electronic theodolite, electronic
distance measuring instrument (EDMI), and an electronic data collecting system. The system also
includes tripods, tribrachs, prisms, targets and prism poles. The TSSS system is used to perform
the conventional survey methods of traverse, network, resection, multiple ties, and trigonometric
leveling This will be useful for planning all future village developmental activities. Survey
control points established with TSSS can be linked with Geo-coordinates and the data obtained
is directly transferred to a personal computer and digital maps are generated. This process will
yield highly accurate survey field data. Survey using GPS and Total station ensures Millimeter
accuracy. Compared to the traditional method of survey, Total Station survey results in lot of
savings in terms of time, money and man days while ensuring more accuracy and lending itself to
easy access, retrieval and utilization of data.
The levels required shall normally be co-related to Mean Sea Level. Permanent as well as
temporary benchmarks shall be established at prominent places within the village for future
requirements.
a) Detailed „L‟ section survey should be carried out along the existing roads for all pipelines
and distribution system network. Levels shall normally be taken at 15 m intervals. If
necessary, additional levels may be taken at road junctions, bends or peaks and valleys.
Typical details to be included in a „L‟ section and cross section are presented in Fig. 12
b) Net levels (Grid levels) are taken usually at 5m intervals for block survey of OHSR/UGSR
sites, treatment plant sites, pumping stations and intake structures.
c) The trial pits for pipelines shall be of size 1m x 1m and for a depth of about 1m to note the
nature of soil preferably at 500m intervals.
d) However, trial pits for other structures shall be taken to a depth of up to 2m to note the
nature of soil and subsoil water if any. Bearing capacity of the soil is determined by SPT
method and soil samples collected and tested in laboratory to co-relate the results obtained
in the field. For exceptional cases such as very loose soils or filled up soils, detailed soil
analysis may be required.
56
6.2 Selection of Source:
The origin of all sources of water is rainfall. Water can be collected as it falls as
rain before it reaches ground; or as surface water as it flows over the ground; or it can be
collected in ponds/lakes; or as groundwater as it percolates down to aquifers. However, in
Punjab state the main sources of water for irrigation and drinking purposes is ground water
and surface water from irrigation canals. Depending upon the availability of potable water
in the region the source of water supply is selected as surface or ground water.
6.3 Groundwater based Schemes:
Ground water based water supply schemes shall have generally following components.
6.3.1 Tube Wells:
Underground water which is abundantly available in most districts of Punjab is tapped
through installing Tube Wells. Tube Wells shall be drilled in accordance with Indian
Standard IS:2800 ( Part- I )-1979 with latest amendments, developed in accordance with
IS:11189-1985 with latest amendments and tested in accordance with IS:2800 ( Part-II )-
1979 with latest amendments .
General Requirements:
Size of Tube well- M.S housing pipes confirming to IS:4270- 1983 with latest
amendments of nominal bore dia. 200 mm to 250 mm shall
generally be provided in most districts of Punjab. Length of
Housing pipe shall depend on depth of water table, draw down and
submergence requirements of pump.
57
6.4.3 Pumping Machinery
In a rural water supply system, pumping machinery serves the purpose of pumping water from
bore wells or for pumping raw water from source to treatment plant and treated water to the
service reservoir. In water supply schemes the pumps may be centrifugal or submersible pumps
are used for pumping water from sumps to Overhead tanks. The centrifugal pump essentially
consists of one or more impellers equipped with vanes mounted on a rotating shaft and enclosed
by a casing. Centrifugal pumps commercially available have a speed range of 980 to 2900 rpm
and the most common speed is 1440 rpm. High-speed pumps have smaller life span due to
increased wear and tear though the size of the pump set is small. Some times Vertical turbine
pumps are used for pumping water from jack wells.
Generally Submersible pump set conforming to IS:8034-1976 (Refer annexure H for detailed
specification) shall be provided . The pumping hours shall be determined keeping in view
availability of electricity. Capacity of pump shall be sufficient to fill the elevated tank with in the
stipulated pumping hours . In the submersible pumps, the bowl assembly is directly connected to
a submersible vertical electric motor suitable for working under water and the compact assembly
thus formed operates below the surface of the water in the well. Delivery of water to the surface is
through the riser pipe on which the assembly is suspended. The power is supplied to the motor
through a flat type cable designed for working in under water condition. These pumps are usually
operated at a motor speed of about 2900 rpm.
To minimize the suction head, submersible pumps may have to be lowered inside the well. In
most of the rural water supply schemes the source is a bore well hence submersible pumps are
preferred for which suction head is zero. Star rated pumping machinery should be used to save
energy and increase efficiency.
6.4.4 Criteria for pump selection
Prior to the selection of a pump for pumping station, detailed consideration has to be given to
various aspects. The hours of pumping are decided and the quantity of water available in the
source is also calculated. Then the discharge of the pump set is calculated in terms of the lps
(liters per second). Friction head and the total head for the pump set are calculated for the given
diameter of the pumping main. Assuming a suitable efficiency and knowing the discharging head
the horsepower of the pump set is calculated by referring to the pump manufacturer‟s catalogue.
After the required HP/KW is calculated; if water is to be lifted from the tube well submersible
pump is chosen or if a centrifugal pump is chosen for other locations, reference is to be made to
the relevant (either submersible or centrifugal) catalogue of the commercially available pump
sets.
The final selection of the pump shall be based on the commercially available KW/HP for the
given discharge (Q) and Head (H) . Selection tables 6.1 & 6.2 based on above referred
consideration are given below :
Water rating Table 6.1 : Outer Diameter of Pump =150 mm
HP/KW Discharge in LPM
240 480 720 840 960 1200 Out let dia mm
Total head in meters
5.0/3.7 22 19 17 15 13 7 100
6/4.5 35 31 26 24 21 12 100
7.5/5.5 47 35 32 25 16 - 100
10/7.5 60 52 45 41 36 21 100
12.5/9.3 72 63 54 49 43 25 100
15/11 85 74 64 58 51 30 100
17.5/13 96 84 72 66 58 35 100
20/15 108 96 82 74 65 38 100
58
Water Rating Table 6.2 :Outer Diameter of Pump =200 mm
HP/KW Discharge in LPM
600 900 1200 1500 1650 1800 Out let dia mm
Total head in meters
7.5/5.5 22 21 19 16 14 11 100
12.5/9.3 39 36 32 26 22 16 100
15/11 44 41 37 31 26 21 100
20/15 57 52 47 38 27 - 100
25/18.5 66 62 56 47 40 32 100
30/22 88 82 74 63 52 42 100
35/25.7 110 103 93 79 66 53 100
20/15 108 96 82 74 65 38 100
Star labeled pump set are available in 2-25 HP and head of 29-317 m.
6.4.4.1 Limitation on Suction Head:
For centrifugal pump sets suction head shall be limited to 4.50 m. In case where suction
lift exceeds 4.5m, the centrifugal pump may be installed at suitable elevation with reference to the
water level to restrict suction lift to 4.5 m. Where the suction lift exceeds 6m, it is preferable to
provide submersible pump or turbine pump depending on the site conditions.
6.4.4.2 Pump Efficiencies:
The efficiency of pump sets depends on the friction and turbulence within the pump set
and mechanical and leakage loss. A pump set is chosen depending on the discharge and head i.e.
Q and H. Pump performance curves are provided by the manufacturers. Choice of pumpset from
among the various manufacturers shall be such that the pumpset has the highest efficiency for the
given duty conditions. Though the pump is chosen for the design duty conditions, in practice the
head may vary depending on the actual water level in the source and friction head on the delivery
point. Such a condition will result in the pump delivering more water due to reduction in the head.
This will decrease the efficiency of the pump set and may also increase the power consumption.
Some times, the variation may be so high that the amperage of the motor will also increase
resulting in failure of motor winding. Hence, it is desirable to avoid over design of the pump sets
and it is suggested that the pump chosen shall work within plus 5%or minus 25% of the range of
the maximum efficiency point of O & H given in the family curve.
Fig 4 (of drawings) annexed with this manual presents characteristics of a pump under a
constant operating speed. It can be seen from the figure that each pump has a maximum
discharge at a minimum head, below which the pump will not work. Similarly at zero discharge
(when discharge valve is closed), the head developed is maximum and is known as shut off head.
Also it can be seen that maximum efficiency is obtained at a particular discharge. This point is
nearer to the middle of the range of head and discharge of the pump. Normally, performance
curve for each type of pump will be given in the pump manufacturer‟s catalogue. In some
catalogue instead of performance curve, water-rating charts will be given. These indicate range of
head and discharges applicable to the particular type of pump. Hence, for a known head and
discharge, from the range of pumps available, the most efficient one is the pump in which the
required head and discharge lies near the middle of performance curve or water rating table. This
also ensures satisfactory performance of the pump under varying head and discharge during
pumping. Efficiency of pumps increases with higher star rating of pumps.
6.4.4.3 Pump Installation: Submersible Pumps:
Submersible pumps shall be installed in a bore well such that the motor assembly is always
submerged in water. Hence, normally they are installed at 1.5- 2.0 m below the lowest safe yield
59
level during summer under continuous operation. Hence it is necessary to install Electronic water
level indicators to read the water level in the bore well ensuring the required minimum
submergence (1.5m) also to avoid drawing of the silt/sand from bottom it is preferable that lowest
part of the pump is 3.0m above bottom of the well. The motor assembly is suspended through the
riser pipe, which in turn is clamped at the top of the casing pipe. The insulated cable is tied to the
riser pipe at regular intervals. The casing pipe is taken to height of about 0.45 m above the ground
level and is covered in order to prevent misuse.
6.4.4.4 Accessories
Indoor control panels where pump chamber are provided or out door type control panel for
bore well pump sets will have provision for energy meter, main switch, starter, single phase
preventer, capacitor, etc.
a) Switches: A main switch of adequate capacity to disconnect power supply shall be
provided after the meter. This will enable to disconnect the service immediately in case of
any emergency or for maintenance purpose.
b) Starter: Starter with over load relay is provided to start and stop the motor and to protect it
against any over load. Over load may be either electrical or mechanical.
c) Capacitor:- Installation of capacitor of suitable rating in the motor circuit will improve the
power factor and reduce energy consumption. The running cost of the motor will also be
reduced. The recommended capacitor ratings are given below. It is essential to provide
capacitor to avoid penal action from the PSEB. Typical components for starter and power
capacitor rating for different range of motors are presented below.
d) Single phase preventer :- In three phase circuit, three fuses are provided (1 for each
phase). If in any one phase fuses were to blow or any one phase is disconnected form
service during running of the motor, the motor keeps running drawing excess current from
the two lines and hence causing damage to the motor. If a single phase preventer is
provided in the circuit, it will sense the operating coil and trips the starter and protects the
motor from burning.
e) Voltmeter and three phase ammeters: - These meters will indicate whether system voltage
is within permissible range for the motor or to know whether motor is drawing current
equally on all three phases. The functioning of Voltmeter is very important, voltage being
low in villages damaging the motors.
(f) Selector Switch:- Selector switches of adequate capacity shall be used wherever more than
one pump is installed. The selector switches will enable to operate any one of the pump or
both the pumps from a single switch board.
Components for starter and power capacitor for different range of motors are given in Table 6.3:
Table 6.3:
Sl. Range of Motors Starter Type Cables (copper Capacitor MCB Volt meter Ammeter
No conductor wires) KVAR Ams
1 Upto & inclusive of 3 HP D.O.L 2.5 Sq.mm 1 20 0 to 500 V 0-15A
2 Above 3 HP upto and D.O.L 2.5 Sq.mm 2 20 0 to 500 V 0-15A
inclusive of 5HP
3. Above 5 HP upto and Star delta 4.0 Sq.mm 3 32 0 to 500 V 0-30A
inclusive of 7.5HP
4 Above 7.5HP upto and Star delta 4.0 Sq.mm 4 40 0 to 500 V 0-30A
inclusive of 10HP
5 Above 10HP upto and Star /delta 6.0 Sq.mm 5 40 0 to 500 V 0-60A
inclusive of 12.5HP
6 Above 12.5HP upto and Star / delta 6.0 Sq.mm 5 63 0 to 500 V 0-60A
inclusive of 15HP
60
6.4.4.5 Electrical Connection
Use of underground cable is usually made for service connection from PSEB supply point
to energy meter fixed inside the control board. Internal connections from meter to switch to starter
to capacitor and to single phase preventer etc. are done using suitable P.V.C. insulated copper
wires of 440 volts grade. From load side terminals of starter to submersible pump, suitable water
proof PVC insulated copper cable of 3 core type has to be laid. Use of under ground cable of 4x
105mm dia aluminum conductor, PVC insulated, PVC sheeted 1.1 kV class is usually used
from PSEB supply point to energy meter upto 15 HP loads. Use of 3 core PVC insulated PVC
sheathed copper conductor, water proof cable is used from starter terminals to pump terminals
(inside bore). All the electric installations including transformer if any is checked by Chief
Electrical Inspector before release of electric connection by PSEB.
a) After installation, it shall be tested to ensure that the wires / cables used are sufficiently
insulated to avoid leakage of current.
b) For safety, all the metallic casing of enclosure of switches etc. must be solidly connected
to earth. The body of the out door kiosks shall have a separate and efficient earth connection.
1. Trial Operation:
The operation of centrifugal pumps is quite simple and safe. There are relatively
few valves to operate and the pump will not be damaged even if the discharge
valve is closed for short periods of time.
2. Starting:
The pump must be primed before it will deliver any water. Failure to prime the
pump may cause the wearing of rings rub and seize or the shaft may be scoured at
the packing boxes. During starting it is desirable to have the vent cock in the
casing open slightly to remove any dissolved air in the water.
It is necessary to have the discharge valve closed so that the least load is thrown on
the driver when the pump is started. The valve should be opened gradually to avoid
over load on the motor and to prevent a sudden surge in the discharge line.
3. Shutting Down
When shutting down, the discharge-valve should be in the same position as when
starting up by closing the discharge valve gradually so that less power is dropped
from the line and any sudden pressure surges in the pipe system are avoided.
3. Inspection and Maintenance
Manufacturers supply instruction books that give directions for the operation and
maintenance of each pump.
If the base is not too rigid the shaft alignment should be checked occasionally.
Normally a centrifugal pump does not start pumping water immediately after switching on
due to failure of priming. This may be due to a clogged foot valve or entrapment of air on the
61
suction side. It is suggested that the pump is reprised by allowing more water to fill the suction
line by opening the by-pass valve on the delivery side. Usually this may be sufficient. If the
pump still does not deliver water then detailed inspection has to be done for any mechanical
clogging of the foot valve or due to visible leaks on the suction side. In case of submersible
pumps since suction head in zero, the above problems will not arise.
If the pressure gauge on the delivery side does not register a gradual increase it means that
the water is not being delivered at the desired pressure or at the desired quantity. This may be due
to any leakage on the pumping main or burst of the pipeline due to the closure of any valve on the
pumping main. In such case, the pump has to be shut down and inspection undertaken on the
delivery side for any leakage.
If the motor itself does not start or if the speed is slow it indicates electrical problem due
to single phase current, low voltage or no power supply to the main switch or any fuses might
have been blown. In such case, the main switch is to be switched off and verification done for the
required voltage or replace any burnt fuses. During running of the pumps the ammeter should
always show the designed value of consumption of power. If the pump is over loaded for any
reasons and if the voltage is lower, it will indicate a higher value of amperage in which case also
the motor is to be switched off and resumed only after the required voltage is observed. If all the
above problems persists, if any vibrations are noticed and if any unusual noise is observed the
manufacturer is to be contacted.
In case of submersible pumps, if there is no discharge it may be due to:
i) Chocked strainer
ii) water level in the well being lower than the pump level
iii) single phase current, low voltage or no power supply to the main switch or any fuses
might have been blown.
If the problem is with the power supply the remedial measures as discussed above shall be
followed.
If the water level in the well is below the pump level, then sufficient time shall be allowed
for recuperation to raise the water level above the pump level. If this problem persists it may be
necessary to lower the pump. Hence it is essential to maintain the record of water table in bore
well and pump capacity observed to see whether pump needs to be lowered. When none of the
above are the causes for no discharge, the pump shall be removed and checked for the fault.
Disinfection of water shall be carried out using chlorine or silver ionization based plant.
The Silver ionization is a cold sterilization process using special silver electrodes which
discharge silver ions into the water by means of low power direct electric current. es. As the water
passes through the sealed chamber, metallic ions are generated to purify the water. The
microscopic action of the ions with bacteria are twofold. First, the bacteria are destroyed through
a change in their enzyme processes. The ions maintain a stable sanitizer residual in the water until
they are used up by this process.
62
Sketches showing Silver Ionization Process
Major Benefits
Effective protection against reinfection after sterilization
Conservation of the water is maintained over prolonged storage periods
The process ensures constant disinfection of conduits and storage tanks
The silver ionization process entails no risk of corrosion in pipes or storage tanks
The treated potable water is completely tasteless and odourless
Silver ions are non-volatile and retains their residual effect within a wide temperature
range
No moving parts in the unit ensure long system life and keep maintenance to a minimum
b ) Disinfection By Chlorination
Chlorination has become the most common type of drinking water disinfection. It should be
noted that it is designed to kill harmful organisms, and generally does not result in sterile water
(free of all microorganisms). Two types of processes are generally used: hypochlorination,
employing a chemical feed pump to inject a calcium or sodium hypochlorite solution, and gas
chlorination, using compressed chlorine gas.
63
soluble in water and are relatively stable under proper storage conditions, they are often favored
over other forms. Figure below shows a typical hypochlorite installation.
Sodium hypochlorite is available in strengths from 1.5% to 15%, with 3% available chlorine as
the typical strength used in water treatment applications. The higher the strength of the chlorine
solution, the more rapidly it decomposes and the more readily it is degraded by exposure to light
and heat. It must therefore be stored in a cool location and in a corrosion-resistant tank. Typically,
30 minutes of chlorine contact time is required for optimal disinfection with good mixing. Water
supply treatment dosages are established on the basis of maintaining a residual concentration of
chlorine in the treated water.
Water-based solutions of either the liquid or the dry form of hypochlorite are prepared in
predetermined stock solution strengths. Solutions are injected into the water supply using special
chemical metering pumps called hypochlorinators. Positive displacement types are the most
accurate and reliable and are commonly preferred to hypochlorinators employing other feed
principles (usually based on suction). Positive-displacement-type hypochlorinators are readily
available at relatively modest costs. These small chemical-feed pumps are designed to pump
(inject under pressure) an aqueous solution of chlorine into the water system. They are designed
to operate against pressures as high as 100 psi, but may also be used to inject chlorine solutions
under ambient (atmospheric) or negative head conditions. Hypochlorinators come in various
capacities ranging from 3.8 to 227 I/day. Usually, the pumping rate is manually adjusted by
varying the stroke of the pump's piston or diaphragm. Once the stroke is set, the hypochlorinator
accurately feeds chlorine into the system at that rate, maintaining a constant dose. This works well
if the water supply rate and the output of the pump are fairly
constant:
c) Dosatron Technique:
Dosatron technique of disinfecting drinking water is a non-electricity based disinfection
dosing system. It is installed directly on the water supply line, the Dosatron operates by the using
the flow of water as a power source. The water activates the Dosatron, which takes up the
required percentage of concentrate directly from the container and injects it into the water. Inside
the Dosatron, the concentrate is mixed with the water, and the water pressure forces the solution
downstream. The dose of concentrate will be directly proportional to the volume of water entering
the Dosatron, regardless of variations in flow or pressure which may occur in the main line.
64
Chlorine Dioxide (CDD-5000) is used as disinfectant. The benefits of CDD-5000 (Chlorine
Dioxide) are as under:-
1. Residual remain for 72 hours.
2. Easy to transport to water works because it comes in powder from and 2kg
CDD_5000 (Chlorine Dioxide) is enough to make 100 liter solution.
3. CDD-5000 comes in powder form.
4. Shelf life of sealed box is 5 years.
5. 100 liter solution is sufficient for disinfect more than 90 Lac liter of water.
6. Contact time with water for disinfection by CDD – 5000 with 2-5 minute at spource.
7. Residual can be tested at site by existing kits.
8. Effective on all types of bacteria which creates water born disease.
9. CDD-5000 does not form any ill effect on health like cancer etc.
6.5 Transmission:
Conveyance of water may be by gravity flow and/or pressure. Pipelines used for
transmission of water, normally follow the profile of the ground surface closely. Gravity
pipelines have to be laid below the hydraulic gradient. PVC Pipes are normally used for
rural water supply schemes. MS/CI/GI pipes shall be used at all road crossings and in hard
rocky strata regions.
6.5.1 Hazen-Williams Formula
The Hazen- Williams formula is most widely used for estimation of velocity,
discharge and the loss of head due to friction.
V = 0.849 C r0.63 S0.54
Where:
V = Velocity in metres per second
r = Hydraulic radius of the pipe which is equal to D/4 where
D is the Inner Dia of pipe in m
S = Slope of hydraulic gradient m/m
C = Hazen- Williams Co-efficient of roughness
65
g= Acceleration due to gravity in m/s2
k= A specific resistance co-efficient for the specials or appurtenance.
The values of K to be adopted for different fittings are given in the manual on water supply and
treatment published by CPHEEO. However, in a rural water supply system it is recommended to
calculate the head loss due to specials and appurtenances at 10% of head losses in pipeline.
PVC pipes:
These are most economically suited for rural water supply schemes. These have certain
advantages over metal pipes, such as resistance to corrosion, light weight, easy jointing
Specification - IS : 4985-2000
Class - 2.5 kg/sq.cm, 4kg/sq.cm, 6 kg/sq.cm and 10kg/sq.cm
Size - 20 to 315 mm (outer diameter)
Jointing - Solvent welded joints, flanged joints, rubber ring joints
Wall thickness of uPVC pipes are given in Table 6.5
Table 6.5 : Dimensions of Unplasticized PVC Pipes
Note : Average thickness may be considered for design purpose for arriving at internal diameter .
6.5.5 Depth of cover
The pipeline shall be protected against damages due to external influence. Hence, the
pipeline shall not be laid at surface, they shall be laid at sufficient depths to avoid damages. A
minimum cover of 1.0m above the pipeline is to be laid to avoid damage by superimposed load.
When heavy traffic is anticipated, depth of cover has to be worked out after taking into
consideration the structural and other aspects. However in narrow streets 1-1.5 mt wide where no
vehicular traffic is expected and digging deep may cause danger to the stability of adjoining
structures it may be reduced to 60 cm . Distribution mains and pumping mains can be laid along
the road berm to avoid load due to vehicular traffic on the pavement of road. When road is to be
crossed, GI/CI pipes are preferred to PVC pipes.
66
6.5.6 Hydraulic testing of the pipe line
After a new pipeline is laid, hydrostatic test shall be done to ensure that pipes and joints
are sound enough to withstand the maximum pressure likely to be developed under working
conditions.
The completed pipeline may be tested either in one length or in sections. Each section should be
properly sealed off with special stop ends and secured by adequate temporary anchors. All
permanent anchors should be in position and concrete should develop adequate strength before the
commencement of test. The section under test should be filled with water, taking care that all the
air is displaced either through vents at the high points or by using a peg or a sphere.
In a pumping main the total head for which the pump to be designed is the maximum working
pressure. However, in the case of submersible pumps, by the time water comes out of the pump
up to the ground level near the bore well the total head will be reduced by the depth of water in
the bore well. Hence, PVC pipes at the bore well location, shall withstand a resulting static head
above ground level plus the head due to water hammer effect. In gravity main the maximum static
head is equal to the hydraulic gradient line minus the lowest ground level along the alignment of
the pipeline.
The test pressure for pipe lines shall be as per following :
Pumping Mains = 50% of Pipe test pressure class or working pressure which ever is
higher
Gravity Lines = 2/3 rd of the Pipe test pressure or working pressure which ever is higher
After filling, the pipeline should be pressurized to the specified operating pressure and left for a
period of time to achieve stable conditions. The pipeline is pressurized upto the full test pressure
gradually and the section under test completely closed. The test should be mentioned for a period
not less than 10 minutes to reveal any defects in the pipes, joints or anchorage. The test pressure
should be measured at the lowest point of the section under test or alternatively, an allowance
should be made for the static head between lowest point and the point of measurement, to ensure
that the required test pressure is not exceeded at the lowest point.
The leakages/ burst if any should be identified and rectified there after the test is again carried out.
6.6 Appurtenances
Appurtenances are valves, which are installed in a pipeline to isolate and drain pipeline
sections for test, inspection, cleaning and repairs, and for expulsion of air. For all appurtenances
provided on line like Sluice valves, Butterfly valves, flow meters etc. be preceded with
dismantling joints which will facilitate their removal for repairs or replacement. A few of the
commonly adopted appurtenances are discussed herein.
6.6.1 Sluice Valves
Sluice valves on main line are provided to stop and regulate the flow of water in the course of
ordinary operations and in an emergency. The principle considerations in location of the valves
are accessibility and proximity to special points such as branches, stream crossings, major summit
points etc.
Sluice valves of the same size as per diameter of the main line pipe are normally used for isolating
sections of pipe. Sluice valves are sometimes used for continuous throttling which may cause
erosion of seats and lead to body cavitations. Wherever small flows are required, the bypass valve
is more suitable for this purpose as compared to throttling the mainline valve Fig. 5 presents the
details of a sluice valve.
6.6.2 Butterfly Valves
This valve contains a circular disc which rotates in the direction of flow in pipe. It is a type of
flow control device that is used to regulate flow of fluid through a section of pipe. This valve is
67
similar to ball valve in operation. A flat circular plate is fixed in the center of pipe.These valves
are:
Rigid and sturdy design with minimum loss of head across the valve
Compact, light weight, low operating torques
Eccentric seat geometry results in less wear and tear and longer life
Self cleaning and non jamming seat design
Valve should be confirming to IS 13095:1991 (Reaffirmed 2003). Typical flanged and wafer
butterfly valves are given in Fig. 3 (of drawings).
68
Figures depicting Kinetic Air Valve
Typical Sizes of Kinetic Air Valve
VALVE
A B WIDTH SUITABLE FOR MAIN SIZE
SIZE
40 370 440 210 Up TO 100
50 410 440 210 125 TO 200
80 430 505 235 225 TO 350
100 500 635 280 400 TO 500
150 620 860 430 600 TO 1200
200 735 990 505 100 TO 1200
B) Small Orifice Air Valve : The purpose of this valve is to discharge air which may accumulate
in sections of a main under working conditions , that is under the running pressure in the main .
The orifice is relatively quite small and is sealed by a floating rubber covered ball at all pressures
above atmospheric pressure except when air accumulates in this valve chamber . When air has
accumulated to depress the water level sufficiently the ball falls away from out let orifice and the
air escapes through this orifice until the water level rises again causing the ball to re seal the
orifice . The diameter of the ball in a small orifice air valve is related to maximum working
pressure and for a given size of orifice increase with this pressure . The orifice is not less than 2.5
mm in diameter
69
C) Double Air Valves : In many instances both large and small orifice air valves are required at
the same point on a main and it is usual in such casaes to fit a combined air valve in a single
fitting .
Air inlet valves are used at peaks. A manually operated sluice valve is introduced between the air
valve and the main pipe to isolate the air valve for the repairs. Normally, air valves are used with
size equal to D/4 where D is the diameter of the main pipe on which the air valve is placed. Fig 6.
is a typical sketch showing location of air Valves and scour valves.
6.6.5 Reflux Valves
Reflux valves are also called check valves or non-return valves, which automatically prevent
reversal of flow in a pipe line. They are useful in pumping mains when positioned near pumping
stations to prevent back flow when the pump is shutdown. The reflux valve is normally provided
on delivery side of each pump to prevent back flow into pump impeller and to avoid rotation of
impeller in reverse back flow into pump impeller and to avoid rotation of impeller in reverse
direction. The size of the valve is equal to the same size as the pipeline on which it is installed.
Reflux valves shall have by pass valves, which can be used for priming of the suction line before
starting of the pumps.
70
towards the pump set (with a reversal of the direction) and velocity increases by several times
causing water hammer. This pressure rise or water hammer results in a series of shocks, sounding
like hammer blows, which may be of sufficient magnitude to rupture the pipe. The pressure due
to water hammer depends on the elastic properties of the pipe material.
H max = CV
g
C= 1425
1+Kd
EC1
Where
H max = maximum pressure in the closed conduit above the normal pressure in m.
C = velocity of pressure wave travel m/sec.
g = acceleration due to gravity in m/sec2 (9.81/ms2)
V0 = normal velocity in the pipeline before sudden closure in m/sec.
K = bulk modulus of water (2.07 x 108 Kg/sq.m)
D = Inner diameter of pipe in m
C1 = wall thickness of pipe in m
E = modulus of elasticity of pipe material
For D.I pipes =1.7 x 1010 Kg/ sq.m
For PVC/HDPE pipes = 3.0x108 Kg/ sq.m
For C.I pipes =7.5 x 109 Kg/sq.m
For steel pipes =2.1x 106 Kg/sq.m
The actual water hammer head can be calculated and added to the working pressure to arrive at
the class of the pipe which shall be able to withstand the total head on account of water hammer
plus the working head. Water hammer is contained in small size pipe lines by operating them at
lower velocities (not more than 1 m /sec.) Since water hammer head is a function of velocity,
choosing a higher diameter pipeline reduces the velocity and hence reduces the water hammer
head. However, cost effect has to be studied for choosing higher diameter pipe to minimize water
hammer head or chargining the pipe material or increasing the pressure class of pipe to withstand
the water hammer head.
71
a) The period of design considered or period of loan repayment.
b) Different pipe sizes against different hydraulic slopes.
c) Different pipe materials, which can be used for purpose and their relative costs as laid in
position.
d) The duty, capacity and installed cost of pump sets required against the
corresponding sizes of pipelines under consideration.
e) The recurring costs on
ii) energy charges for running pump sets.
iii) staff for operation of the pump sets
iv) cost of repairs and renewals of pump sets
v) cost of miscellaneous consumable stores
While selecting the class of the pipe higher of the following shall be considered
i) Twice the working pressure at the top of the bore well.
ii) Working pressure at the top of the bore well water hammer pressure.
Note : Economical size of Pumping main can be calculated by using the software in MS Excel
available with DWSS . Example of such design is enclosed at annexure – O-6
6.7 Environment Management Framework
Sector Environment Assessment (SEA) for PRWSS project was prepared by Feedback Turnkey
Engineers in September 2006. The main focus of the report was water supply schemes. In 2010,
Consulting Engineers Services updated the 1st EMF in the light of sewerage schemes. The present
study includes updation of existing EMF on environmental issues in the context of PRWSS
Project- II, including environmental sanitation and rain water harvesting techniques and its
integration with water supply and sewerage schemes, proposed Institutional Arrangements, water
quality monitoring, water and waste water sampling procedure, environmental concerns and
management proposals, capacity building etc. In line with state policy, demand responsive
approach, active involvement and participation of PRIs and beneficiary communities through all
stages of the project implementation and its sustained operation and maintenance will be the key
features of this EMF.
In order to ensure that the environmental issues are systematically identified and addressed in the
various stages of the implementation of the schemes, an Updated Environmental Management
Framework (EMF) has been developed for this project. EMF activities in the pre-planning,
planning, implementation and O&M phases of the proposed project cycle for the project
sponsored schemes are given in respective tasks. The key elements of EMF are as follows:
6.7.1 Environmental Data Sheets on Water Supply and Sewerage Schemes - The EMF
requires the basic environmental data pertaining to the proposed schemes be compiled at the
field data collection stage. For this purpose, a simple Environmental Data Sheet (EDS) has
been formulated on water supply, sanitation/ sewerage schemes. Refer Annexure-L.
6.7.2 Environmental Categorization of the Schemes - At the Detailed Scheme Report (DSR)
preparation stage, the available environmental information in the EDS will be evaluated
and based on the level of expected environmental and public health impacts, the proposed
72
scheme would be classified.In case of water supply schemes, the schemes shall be
classified as either Category I (environmental data sheet to be prepared) or Category II
(detail environmental appraisal is required).In case of sewerage schemes, the schemes shall
be classified as either Category I (environmental data sheet to be prepared) or Category II
(detail environmental appraisal is required).
Categories of Water Supply Scheme
Category I (Minimal Impacts where EMP Category II (Significant Impacts where
not required) EMP required)
Water Supply involving pumping, Water Supply involving pumping,
construction of storage tanks and piped construction of storage tanks and piped
distribution networks, with source as tube distribution networks, with Surface water as
well/bore well. a source.
Water Supply with water source requiring Water Supply with water source requiring
minimum treatment such as disinfection. “Advance Treatment” for removal of
arsenic, iron, fluoride, salinity, etc.
Single Village Scheme (SVS) with either Multi Village Scheme (MVS) based on
surface water or ground water source. either surface water or ground water source.
Water Supply with source in shallow aquifer Water Supply with source located in/very
in safe and semi-critical zone and with source close to natural habitat/sensitive eco-
in deep aquifer located in safe zone of systems such as National Parks, Wild Life
exploitation. Sanctuaries (requiring forest
permission/clearance)
No water quality issues with regard to ground Water Supply with water source from
water source. critical aquifers/over exploited zones.
Ground water based scheme, if the water
quality testing for deep groundwater source
indicates unacceptable levels of pesticides
or heavy metals.
73
6.7.4 Environmental Management Plan (EMP) for pre-planning, construction and O&M
phase impacts – EMP based on issues identified during the planning stage of the
proposed project and necessary preventive and mitigation measures should be considered
in the design. The contractor shall provide an undertaking for execution of the activities
identified in the EMP. The EMP shall be initiated at the planning and design stage of
project and the process shall involve addressing relevant environmental issues ranging
from household to village level with appropriate detail.
6.7.5 Provision for Environmental Cost - Provision of 2% of capital cost of water supply and
sewerage schemes towards EMP is notional. If the cost of implementation of EMP is more
than 2% then the actual cost to be factored in the cost of the scheme.
6.7.6 Flow chart of EMF activities :The following environmental frame work flow chart
provides the understanding of the EMF activities to be taken up at various stages of the scheme
including environmental monitoring with regard to performance indicators:
74
SCHEME PROCESS ACTIVITY EMF ACTIVITY REPONSIBILITY FOR EMF
The Training and Capacity Building programs has been proposed for the project, the aiming of
this is building environmental awareness and environmental management capacity in the
project
administration structure as well as in the intended target communities.
Sr. Training Purpose of the Training Participants Duration Resource
No. Persons/Agenci
es
1 Introduction to Filling of EDS, procedural & Field Staff – Orientation Services of the
Environmental technical aspects of EEs. SDEs & Workshop – 1 experts from
Management Environmental Assessment JEs) day at circle outside agencies
in Proposed To equip with knowledge and SEs, EEs, SDEs, level such as PPCB and
RWSS project skills necessary for undertaking Environmental its affiliated
including EMF environmental appraisal as per Experts – Training and
the requirements of the EMF. Lab Technicians Research Institute,
To undertake periodic – National
supervision of environmental Productivity
performance of schemes Council (NPC)
To prepare for planning and Delhi/ ESCI,
monitoring implementation of Hyderabad etc.,
environmental mitigation may be engaged.
measures identified through the
appraisal process.
To equip with skills necessary
for water quality testing using
the field testing kits under the
community based system for
water quality monitoring and
surveillance.
2 Training on To equip with knowledge and SEs, EEs, SDEs, Training Outside agencies
Environment skills necessary for undertaking Environmental Programme – 5 such as National
Management environmental assessment, Experts days Productivity
Framework appraisal, practices, water Council (NPC)
quality testing as per the Delhi/ ESCI,
requirements of the EMF Hyderabad etc.,
3 Environmental To build awareness on safe Environmental One day
Awareness and drinking water, water Staff – workshop at the
Sensitization conservation, judicious use of GPWSC/SLC village level
water sources for competing members One day
demands, environmental workshop
sanitation and personal hygiene. organized
annually
Total training
programs will
be about 176 for
the project
duration.
4 Orientation for To build awareness on water Field Staff – One day
Water Quality quality monitoring amongst EEs. SDEs & training at the
monitoring for implementation agencies. JEs) circle level
PRIs Env.Staff, One day
GPWSC/SLC training to be
members organized
annually.
The details of relevant ECoPs for following activities are described in the report:
– Identification of Sources of Water Supply
– Site Selection for STP
– Identification of Quarry Sites / Borrow Areas
– Selection of location for Community Toilets
– Protecting Source water supply source and Ensuring its Sustainability
77
– Protecting Ground Water Supply Sources and Ensuring its Sustainability
– Selection of Safe Sanitation Technique Options at individual household and
community level
– Solid & Liquid Waste Management at Individual Household and Community level
– Safe Sullage Disposal and Organic Waste Management
– Rain Water Harvesting Techniques
– Management of Water Supply System
– Rehabilitation of Construction sites / Supplementary Sites
– Schemes in Forest Areas
– Water Quality Monitoring and Surveillance
– Water and Waste Water Sampling Procedure
– Construction site management/ Labour Camp
– Occupational Health &Safety
78
CHAPTER-7
DISTRIBUTION SYSTEM
The treated water shall be pumped into the ground level reservoir situated at elevated places
in the village or to the overhead water tanks. The stored water shall be distributed through
appropriate pipe network system in the designed quantity at adequate pressure. The type of
storage tanks and their design and the design of distribution network system are discussed in
this chapter.
7 General guide line for selection of water works and OHSR site
Site selection criteria for Water Works and OHSR site :
a. For Rural Water Schemes Based on Tube Well as source of Water :
Site should be located at a site where there is possibility /indication of getting adequate yield
of potable water from under ground source on sustainable basis. Resistivity method can be
used to determine adequate availability of Ground water where ever required
Site should have independent approach
Site should be adequate so as to adjust proposed as well as future extensions structures . It
should be preferably located in such a way that adequate space is available between OHSR (
Over Head Water Tank) and adjoining structures / private buildings .
Site should not be flood prone and should not be low lying and there is no flow of sullage
/sewage towards it . Site should normally be away from ponds to avoid leaching action of
pond water in to Tube Well water .
Site should normally not be abutting or adjoining cremation grounds and dumping site of
rubbish from village . In case it is not possible locate site away from cremation ground
adequate green cover / boundary wall shall be provided to isolate the water works site from
the cremation ground
Site should not be located on recently filled / made up ground / mound or on edge of rock
where soil erosion can take place with rain water or other wise . It should be preferably a firm
ground .
Site should be located such that working of Tube Well proposed on it is not affected by
working of private irrigation/ government Tube wells if any installed in near viscinity .
Site should be located at such a place so the there is no hindrance / objection from defence
authorities / security agencies for the construction of OHSR . It should be free from over head
electric / Tele phone cables.
In case of multi village schemes site should be so selected that it is most economical also as
regards to length of rising main to UGSR / Height of OHSR and sizes of distribution main
pipes to villages .
7.1 Planning and Design Over Head Services Reservoirs
The water from the ground water source or treated water from surface shall be stored
properly and then distributed through network of pipes by gravity. Elevated service reservoirs
are the most commonly adopted structures for the above purpose as they can be constructed at
a suitable location within the village. Following are the parameters to be considered in design
of such overhead water tanks.
79
7.1.1 Capacity and Location
. Capacity of OHSR shall be calculated by Mass curve method keeping in view the
realistic availability of Electricity and water supply hours . Two number typical mass curves
are enclosed at annexure O (5) as sample for different types of conditions of availability of
electricity . The storage capacity of service reservoir shall be taken on the basis of mass curve
plotted as per actual availability of electricity and the actual water supply hours or 30% of the
daily requirement. Hence before fixing the capacity of OHSR mass curve should be plotted
for all the three shifts and OHSR capacity should be worked out for worst case scenario. The
tank shall be located such that the minimum residual pressure at the remotest point in the
village is at least 12 mts. If elevated lands are available at a reasonable distance, ground level
reservoirs can be proposed for storage of water. If such location is not available, an elevated
service reservoir can be proposed with staging such that it gives a minimum residual pressure
of 12 mts after counting for loss of head during peak hours due to simultaneous opening of the
all the taps on the distribution system
7.1.2 Staging
The staging height of the tank shall be such that, a minimum residual pressure of 12m
of water is maintained at the farthest/ highest point in the distribution system. The staging
height of reservoir is normally kept at 15m (Generally the staging height varies between 15m
to 35m). It is desirable to locate the reservoir at the highest point in the village so that the
staging height is minimized.
7.1.3 Shape
The overhead water tanks should be made of Reinforced Concrete and can have
shapes preferably circular and intze type..
7.1.4 Standardized Capacity and sizes of Pipes :
Through the capacity of tank required varies from village to village for rural water supply
systems to be installed in this project, it is preferable to have standardized capacity. Following
standardized capacities along with sizes of pipes shall be used :
(As per CE circular no 42449-51 dt 31.10.90 and 56127-29 dt 16-12-93)
S. No. Capacity in FSL in metre Size of Pipes in MM
Cum
Inlet Pipe Outlet Pipe Over Flow Scour pipe
80
The outlet from the OHSR shall be equal to the diameter of the first pipeline in the distribution
system starting from the OHSR. The outlet shall be placed atleast 150mm above the floor
level/ bottom of the OHSR.
The overflow pipe shall be equal in diameter to the inlet pipe so that the water coming into the
reservoir and overflowing quantity will be equal. The overflow pipe is located with its invert
at maximum water level of the OHSR.
The scour/ washout pipe in the OHSR will be located at the lowest point in the floor of the
OHSR. It is desirable to lead off both the overflow water and the scour-washout water towards
the nearest drain the hence these two pipes must be located adjacent to each other. Some times
the overflow pipe and scour (washout) pipe are joined to the same chamber near the OHSR at
ground level and later drained by a single gravity pipe to the nearest available drain. At times
the overflow water will be wasted for long periods due to lack of communication between
pump house and water tank locations. To avoid such wastage the overflow pipe of the OHSR
is joined to the outlet pipe of the OHSR so that the overflow water is used in the distribution
system instead of wasting.
It is desirable to provide bell mouths for inlet, outlet and overflow pipes to ensure smooth flow
and strainers to the outlet pipe to ensure that no undesirable particles enter distribution system.
The overflow and scour pipes are also provided with strainers at the termination points in the
masonry chamber to avoid entry of insect etc. Fig.8 (of drawings) gives a typical sketch of
elevation of an ELSR and arrangement of pipe connections for an OHSR. In addition, Fig.9
(of drawings) gives the typical sketch of fencing details.
Vertical piping provided for reservoir for inlet, outlet, and scour cum overflow should
be cast iron double flanged pipes. The flanges shall be machined to ensure that the pipes are
true to plumb and the joints with bolts and nuts are leak-proof. All the pipes entering the tank
and coming out of the tank shall be located at the floor of the tank. It is desirable to keep the
puddle flanges in the floor slab of the OHSR before concreting. However, while embedding
the same, care must be taken to ensure that the flanges are true to plumb so that the vertical
pipes connected to the OHSR are also plumb sometimes it may be necessary to fix the flanges
after the concreting of the floor slab is done. In such cases it is suggested that suitable
grouting compounds may be used to ensure that no leakage occurs through the floor slab at
pipe locations.
The vertical pipes may be marked with direction of flow and to identify the inlet,
outlet, scour and overflow. Color scheme be adopted
1) Inlet :- Green 2) Outlet :- Blue
3) Overflow :- Red 4) Scour :- Yellow
Similarly the Control Valves also shall be identified by proper marking. Control valves are
provided below the ground level in suitable masonry chambers and shall be vertical and true to
plumb. Sometimes a bypass connection is made between the inlet into the OHSR and the
outlet from the OHSR. This will facilitate supply of water directly to the distribution system
when the OHSR is taken out of service for cleaning. Supply from bypass may affect the
pressures in the distribution system.
81
7.1.6 Accessories
The standard type design drawings for the OHSR have provision for RCC. Spiral stairs
with RCC handrails, which terminate at the roof. The access from the rooftop into the tank
shall be with aluminium ladder to avoid corrosion. The roof of the OHSR shall be provided
with ventilators covered with GI fly proof mesh. An access manhole is provided just at the
entry point of the RCC ladder below which the aluminium access ladder is provided.
Lightning arrestor along with GI/ aluminium strip conductor is provided. The conductor is run
vertically along one of the columns. A water level indicator shall be installed and located just
above the ground level and connected to the water level in the tank with GI wire and
aluminium pulleys with an anti corrosive float ball in the tank. Care should be taken that the
Indicator is not accessible to the miscreants.
7.1.7 Design Principles
Type designs for RCC reservoirs are provided with this manual. However some basic
principles are noted: The designs of the OHSR are done to cater for gravity loads (i.e. wt. of
structure plus wt. of water stored), wind load on the structure and earthquake loads. The
components of an OHSR‟s can be classified as be are:
Foundation system- It may be raft foundation, pile foundation or individual footings
depending upon the safe bearing capacity of the soil at the site.
The type design of ELSRs are provided for maximum safe bearing capacity (SBCs 8.75T/m2).
However, the actual SBC at the location of the OHSR may vary. It is necessary to make a trial
pit of 2mx2mx2m deep and collect the soil sample at each location and determine the SBC.
Based on the capacity, staging and actual SBC the suitable type design will be used. However
amendments in latest IS codes be strictly incorporated with special regards to earthquake
resistance. The OHSR of various capacities and staging heights are being designed for various
safe bearing capacities by an external consulting agency. These designs and drawings shall be
followed.
7.2 Distribution System:
The purpose of distribution system is to convey wholesome water to the consumer at
adequate residual pressure in sufficient quantity at convenient points. The requirements for the
distribution systems are network of pipes connected to reservoirs with valves at suitable
locations for efficient operation and maintenance. Adequate residual pressure at maximum
demand depending upon the hydraulic capacity of the system should be provided. Normally,
water supply is intermittent in a rural water distribution system. As electricity situation has
improved some schemes have been made 24x7. Hence the distribution system is to be
designed for a peak factor of 3 giving due allowance to higher demand in morning nothing
(assuming demand to be 2/1.5 times the normal supply). The road network pattern in a
village is normally with dead ends and rarely the roads are connected. Though ideally a grid
network is desirable, in a rural water supply system, dead end pipe systems are common. In a
82
dead end system, a single trunk main takes off from the OHSR with smaller mains branching
off from the trunk main. A single trunk main may be sufficient where elevation difference
between highest and lowest point in the village is not more than 4.5m. When the difference in
elevations is more than 4.5m, two trunk mains taking off from the outlet main at OHSR may
be required, one to serve the high level areas and the other to serve the low level areas.
Wherever, it is possible the distribution system of the high level and the low level may be
interconnected to provide emergency supplies. However, the interconnection valves between
the zones shall normally be kept closed.
Note: Depending upon the profile of the village either a dead end or a loop system of
distribution net work may be adopted, for all practical purposes.
Bulk Meters :
Bulk meters shall be provided to measure the quantity water supply to the communities
/habitations. Normally Bulk flow measuring meters shall be provided at Water works site and
at the entry point of each village / habitation. Readings taken from Bulk meters will help in
equitable distribution of water supply and identify looses of water in transmission and
consumption pattern can also be ascertained. Bulk meters shall be installed for each zone also
where network is divided into zones. Mechanical flow meters upto 250 mm size are
economical compared to electromagnetic flow meters, IS-2373 for mechanical meters gives
information on range of registration with minimum and maximum flows required for registration. (i)
First a meter of appropriate size is to be selected based on the flow rather than pipe size to enable
accurate functioning of the meter (ii) Provide up to 250 mm size mechanical flow meters capable
of generation of 4x20mA signals, These signals are required to transmit online through web
based system at a later date. Generation of signals and transmission through web requires an
energy pack good enough for about five years. (iii) install Electromagnetic flow meters with
sufficient energy backup, only if the required size is more than 250 mm and (iv) Irrespective
of the type of meter selected, meters shall be procured with at least five years guarantee.
83
Softwares which will enable hydraulic modeling will be used for larger networks to enable
performance monitoring. Simple SCADA for large Multi Village Water Supply Scheme may be
installed.
7.2.1.1 SCADA
SCADA to be provided where more number of overhead tanks are to be provided and hence
manual control is not possible
Objective is to ensure designed supply of water is done at ESR of each habitation. ESRs
located at highest elevation and or farthest end will often receive lesser water compared to
those ESR s located at lowest elevation and or nearer. Similarly adequate pressures may not be
available at households located in highest elevation which results in pit taps. Hydraulic design
of all networks is done on the premise that all pipelines flow full. System is likely to function
as per design if there is continuous flow from the feeder mains into the ESR s and from ESR s
into the distribution system. Every time the flow is stopped in the feeder mains or in
distribution system, the network drains resulting in air entering into the system and when
again flow is resumed the air is to be expelled fully which requires more time and if air is not
expelled fully the pipes flow in part which affects the hydraulic design. It is desirable that the
water supply is continuous instead of limiting supply hours to prevent draining of pipelines
and associated problem of expulsion of air and likely pollution.
Design Aspects: The design cannot be made so perfect as to have uniform residual heads at
all points. Further though the system is designed for ultimate flows, it has to serve the present
demand which will progressively increase. Hence the hydraulic design done for ultimate
demand is to be checked for residual heads for present demand and intermediate demand also.
The residual heads (pressures) are also to be regulated and need to be adjusted for progressive
changes in demand. The inflow into ESR s has to be controlled to the required rate of flow
and also to control the cumulative flow. Whenever there is no demand in distribution system
the ESR s will overflow and hence the level is to be sensed and the flow into ESR is to be
stopped.
Controls required: System requires to have flow control (both rate of flow and cumulative
flow), pressure control and ESR level control. To achieve this control with manual operations
is infeasible and not desirable. In order to supply water at required design flow and pressure
and to overcome the above situation it is necessary to provide flow and pressure measurement
& control device. Apart from the above the flow measurement also helps in analyzing the
water losses and water auditing in the system.
Control Philosophy:
When the flow varies from the set point of flow then the MOV will operate by
automatic command from the RTU to regulate and achieve the required design flow at
inlet of the ESR
When the pressures vary from the set point of pressure then the MOV will operate by
automatic command from the RTU to regulate and achieve the required design
84
pressure set at corresponding inlet of the ESR. This is better done by a Pressure
reducing valve (PRV) than with BF valve.
When the power failure occurs at pumping station and there is no flow to the MBR
MOV in the inlet of ESR closes by automatic command from the RTU to avoid
emptying the pipeline.
When the power resumes at pumping station and flow to the MBR is resumed the
MOV in the feeder main location and inlet of ELSR and intermediate sump will open
by automatic command from the RTU.
The level in the ELSR will be monitored and transmitted to RTU. When the maximum
water level reaches in the ELSR MOV at inlet will close by automatic command from
RTU. When the water level falls below maximum water level in the ELSR MOV at
inlet will open by automatic command from RTU. The battery back-up system shall
consist of 12V/60AHr capacity battery with charger facility with minimum 24 hour
battery back-up. Solar Connectivity enabled.
Instrumentation such as Flow meters, level sensors, actuator operated BF valves, PLC
panels etc require prompt servicing arrangement. Hence the DSR/ bid document shall
have cost of SCADA with at least five years of O&M.
85
reduced and another analysis carried out. This kind of trial and error procedure is carried out
till residual head at all the points of the network is more or less near to 12 meters. However if
residual head at some points is more than 10 meters, and cannot be reduced, a throttling valve
is to be used at the off-take of the branch.
7.3 Types of valves & their location
Sluice valves :- The size of SV is same as the size of the main upto 300 mm and for
bigger diameters the size of valves is about 2/3 the size of mains subject to a min of 300 mm.
Sluice valves are not used for continuous throttling as there wise erosion of the
scales & body cavitations will occur. It is recommended the change the frequently when the
working is affected.
Butterfly valves:-
The size of butterfly valve varies from 40mm to 2000mm. Disc is turned substantially through
90o from the closed to the open position, on an axis transverse to that of the valve ports.
Butterfly valves should conform to IS 13095:1991 (Reaffirmed 2003).
Scour valves :- In pressure conduits, small gated take-offs known as blow-off or scour
valves are provided at the low points in the line such that each section of the line between
valves can be emptied and drained completely. They discharge into natural drainage channels
or empty into a sump from which the water can be pumped to waste. There should be no direct
connection to sewers or polluted water courses but through a specially designed trapped
chamber or pit. Their sizes depend upon local circumstances especially upon the time in which
a given section of line is designed to be emptied and upon the resulting velocities of flow.
Calculations are based upon orifice discharge under a failing head equal to the differences in
an elevation of the water surface in the conduit and the blow-off less the friction head.
Frequency of operation depends upon the quality of the water carried especially on silt loads.
In the distribution system scour valves are inserted in the scour branch from the main at low
points and at all dead ends. The size of the scour valve depends upon the length of the main to
be scoured. It is, however, about half the size of the main which is to be scoured. The scour
branch takes off from the main through a scour tee which is a special tee with its branch
connection having its invert at the same level as the main with a view to drain out the bottom
sediments.
Reflux valves :- Reflux valves are valves through which flow can proceed in one
direction only. Any tendency for the flow to reserve causes a reflux valve to close and to
remain closed until flow is re-established, in the unique direction. It should close without
causing shock. They are also called non return valves, check valves and retaining valves. In
one application, a reflux valve can be described as a foot valve. The term check valve is
generally restricted to small size mains and which are of the disc type. Check valve can be had
for the vertical as well as horizontal flow conditions. They are used in the house plumbing
system as well as in industrial installation. It has the advantage of rapid closure but has
simultaneously the disadvantage of causing water hammer associated with rapid closure and
causing high resistance to flow. Single door type reflux valves should conform to IS : 5312
(Part 1)-1984.
Pressure Reducing Valves :
Pressure reducing valves shall be provided at the entry point of distribution system to the low
lying areas to control excessive flow of water to the low lying areas
86
Air valves :- These are sited to release the air automatically when a pipe line is being filled
and also to permit air to enter the pipe line when it is being emptied.
In an intermittent system the distribution pipes are becoming empty when the supply is
stopped and draw in air and expel air when the water supply is resumed. Since the house
service connections/ public taps are above the ground level air is expelled or drawn in through
the open taps since these taps are usually kept open in an intermittent system even after the
supply hours are over. However, to cater for situations wherein air has to be expelled or
drawn in, Air Valves are sometimes provided at the highest point in the network. The highest
point is normally at the OHSR premises where an air valve is essentially required. Air valves
may have to be provided in the network, if the network pipes are having several valleys and
ridges. In such case the smallest diameter air valve available are provided at the peaks.
However, for these air valves to function effectively they have to be mounted above the road
level and hence the pipe connecting the main pipeline to the valve is taken away upto the road
boundary and housed in a secured chamber. In view of the complicated arrangement required
for air valves in a rural water distribution system, it is recommended that instead of providing
Air Valves. This will take care of the expulsion of air from the distribution system. While
designing the distribution network, the stand post at the highest level shall be marked
distinctly for using as Air Valve .
7.3.1 Location of the Air Valves
Air Valves are provided at all peaks. Peaks are not judged solely w.r.t. to horizontal datum
but also with respect to the maximum hydraulic gradient. Air valves are necessary at all points
where the pipe line approaching the hydraulic gradient changes its slope to recede from this
gradient .
87
water meters at Annexure –D and for Bulk Meters at Annexure –E. House Service meter
connection has been depicted in figure no13(of drawings).
7.6 Design Approach for Water Supply Schemes in Severe Power Shortage areas :
It has been observed that in some Rural areas there is severe shortage of power
and it results in lower pumping hours and thus availability and reliability of water
supply to the community falls below the design level. At the time of designing such
schemes separate design approach shall be adopted so that water supply to the
community does not get affected . Following critical parameters shall be modified as
per below
S. No. Design Parameter Value for Severly Electricity shortage
area
1 Pumping Hours “ T”
2 Design safe yield for Tube well Daily demand x T e.g for T= 3
hours it is 3 times the daily demand
3 Pump discharge Average hourly discharge x24/ T
4 OHSR capacity To be designed by using mass curve
5 Peak factor for distribution network 24/T
6 DG set May be provided if supply is highly
erratic
.
88
CHAPTER-8
WATER TREATMENT
The chapter provides various methods of water treatment applicable for rural water supply
system. In some parts of Punjab the ground water which is the main source of water supply to
the villages is having quality problems. Most of the water is having excessive concentrations
of fluorides, TDS, hardness, nitrates and iron. Further there are instances of bacterial
contaminations. Where the water quantity & quality problems are severe ground water cannot
be relied upon and hence surface water with minimum treatment may be the only option.
Normally rural water supply systems provide for plain sedimentation followed by slow sand
filtration and disinfections with bleaching powder.
8.1 Water Treatment Processes applicable in rural water supply system are shown below.
Activity Treatment process for Canal water based Water Treatment process for Tube well
number Supply Schemes based Water schemes
1 Intake of raw water through Intake structure and Pumping of water from Tube
carried to water through Inlet Channel well
2 Storage in Sedimentation tank and addition of Chlorination
Alum for flock formation to facilitate
sedimentation.
3 Gravity flow to underground to Suction and Storage in OHSR
scour well
4 Pumping to High level tank Distribution
5 Gravity flow to Slow sand filter beds/
continuous sand pit
6 Gravity flow to Clear water Tank
7 Pumping to Over head service Reservoir after
chlorination /Ionization
8 Distribution from OHSR
Treatment process -A
a) Normally ground water available in Punjab does not require any extensive treatment
and can be supplied with disinfections alone and hence option (a) shown in the above sketch is
applicable. Fluorides, TDS and Iron from ground water cannot be removed easily as treatment
plants for their removal require skilled operational personnel and constant attention apart from
very high Capital cost and O&M cost. Such treatment plants provided elsewhere for removal
of fluorides have become non-functional. The presence of nitrate, in water is due to
agricultural pollution and fecal pollution. There is no economical treatment method available
for removal of nitrates in domestic water supply. Hence it is suggested that the point of
89
contamination of the source with nitrates shall be identified and remedial measures taken to
prevent contamination rather than providing treatment process for removal of nitrates.
Canal
Inlet Channel
Pump to OHSR
Distribution
Treatment option B
. Surface water in Punjab is taken from the flowing streams and canals may be treated and
supplied to the problem villages. Depending upon the turbidity of the surface water, line
diagram (b) is adopted. Whenever, the turbidity is more than 50 NTU it may not be amendable
for plain sedimentation which may require chemical coagulation. Chemically settled water is
not treatable in slow sand filters and hence when chemical coagulation is suggested rapid sand
filters may be required. In view of the high capital cost and O&M cost and lack of skilled
personnel for O & M, the rapid sand filters with chemical coagulation is not recommended
for rural water supply systems and is not dealt in this manual.
8.2 Intake structures for surface water:
When surface water is decide to be the technology option, it calls for specific
structures for the drawl and transmission. The normal units are intake well, collection sump
and pumping arrangements (jack well), raw water rising main. In addition to the above, the
setting tanks, slow sand filters, clear water sump are the other structures required.
8.2.1 Intake works:
These are the structures placed in a surface water source to permit the withdrawal of
water from the source. These are essentially used in rivers etc., where wide fluctuations in
90
water level are expected. Also these works help in drawing water from the most desirable
depth.
Location and Design Considerations:
1. It shall be located such that the raw water can be withdrawn continuously over the
year.
2. It shall be nearer to the raw water sump.
3. The location shall be free from the water currents and swirls.
4. The entrance of large objects shall be prevented by screens.
5. The capacity of the conduit and depth of suction well should be such that the
intake ports to the suction pipes do not draw air. A velocity of 60-90 cm/sec. will
give satisfactory performance.
6. The intake conduit shall be laid in a continuous rising or falling grade to avoid
accumulation of gas or air
Normally intake structure is made of :
1. Pipe Outlet for discharge up to 0.5 Cusec
2. APM out let for discharge more than 0.5 cusec but less than 5 cusec and where
large variation in canal water level are expected
3. Open Flume Outlet discharge more than 0.5 cusec but less than 5 cusec and
where large variation in canal water level are not expected .
4. Siphon Out let where canal is of perennial source and it is running in
excavation
8.2.2 Inlet channel:
Raw water is carried to the sedimentation and Storage tank from the surface water
source through inlet channel. It is so designed as to fill the storage and sedimentation tanks
completing within seven days which is assumed to running days of the canal distributing “Its
normal capacity is taken as three times the daily requirements.
8.3 Storage and Sedimentation of surface water: S&S tanks serve dual purpose of
storage and sedimentation
In sedimentation the water is allowed to settle in sedimentation cum storage tank for a
minimum detention period of 3-4 hours so that the heavier suspended particles settle down and
the turbidity of water reduces to 10NTU and below. Normally sedimentation tanks are
rectangular in nature with length to width ratio 3:1 to 5:1 and the depth of the water will be
between 2.5 to 5.0m these tanks will be provided with sloped bottom for easy removal of
settled solids. Proper inlets and outlets must be provided for uniform distribution of the flow
and collection of settled water. Usually baffles are provided at the inlet and outlet of the
settling tanks. Storage capacity is kept as 15 days requirement where raw water is taken from
canal via distributory, minor etc. and 3 days requirement where connection is taken from main
canal. Evaporation and percolation losses are assumed as 25%.
8.3.1 Suction and scour wells: Scour and suction well s should be located in such a way
that number of bends is reduced to minimum. For rural population above 15000 persons these
should be of 2.50m diameter and for population less than 15000 persons their diameters may
be reduced to 1.5mtr.
8.3.2 Pumping Units: For Rural water supply schemes a population less than 15000
persons the pumping units of raw water and clear water shall be designed for 8 hours daily
91
working. If the population exceeds 15000 person the working hours may be increased to 16. In
any case a pumping set of equal capacity both for raw water and clear water may be provided
as stand by. It should be so arranged that one of raw water and one of clear water pump should
also be capable of being run by a source alternate to electricity.
8.3.3 High level tank: Capacity of high level tank shall be determined by using mass curve
based on actual supply hours and rate of filtration. .
8.4 Filters: The rate of filtration in slow sand filters should be assumed as 50
gallons per 8ft (2500 liters per sqm.) per day while fixing the dimensions of filters,
economical, sizes should be worked out as per example given below. About 25% additional
filters should be provided as stand by i.e. for every four filter beds calculated one extra should
be provided. This practice should be followed for all urban water supply scheme. The case of
water supply scheme for small villages, the stand by provision should be added in the filtering
area and two filter beds for equal capacity should be provided.
Example: Assuming that for every 4 beds, an additional spare bed is provided and the
total area to be provided is 2400 sq.m. then area of the filter bed = 600sqm.
If L is the length of each bed the Breadth, b = 600/L
Therefore total perimeter of walls P= 10x600+6L
L
for minimum total perimeter= dp/dl=0
i.e. 6000 = 6 or L2 = 1000
L2 L = 31.6 meter say 32 meter
b = 600/32 = 19 meter
so the dimensions of each bed will be 32m x 19m.
8.4.1 Filtering media: The size and depth of filtering media to be provided should be
as under:
The filter should consist of 30” to 36” (750 mm to 900mm) sand, supported on 9” to
12” (225mm to 300mm) gravel. The gravel shall be under laid by a system of open jointed
under drainage. The sand shall have an effective size 0 to 3 mm and uniformity coefficient
=2.00
The gravel is usually placed in four layers for a depth of 12” (300mm) graded from
No.10 mesh to 2 ½ ” (6.3 mm to 63mm)
The grading should be such that the voids in any layer are less in size fine particles of gravel
in the larger immediately above the supporting layer.
8.4.2 : Pressure Filters : A single village canal based water supply scheme shall be designed
by using pressure filters to reduce cost as slow sand filters are economical for multi village
schemes . However due care must be taken to train the community for operation and
maintenance of pressure filters.
A pressure sand filter shall have following salient features :
It shall have single valve operation to eliminate leakage from individual valves .
Give visual indication as to the present operation of the filter.
It shall have Multi port valve with quick connect threaded barrel unions .
It shall have Hydraulically balanced laterals to maximize water flow and automatic air
bleed .
Tank of the pressure sand filter shall be made of Fibre Glass .
92
8.5 Clear water Reservoir : As in case of high level tanks the storage capacity of
clear water tank shall be worked out on the basis of the filtration and pumping schedule. Since
the save water and clear water shall be pumped out according to the same pumping schedule
the capacity of clear water reservoir shall be equal to the capacity of high level tank
determined by using mass curve method
For small installations such as small rural water supply schemes, the high level tank,
filter beds and clear water tanks should be provided of circular section.
8.5.1 Over Head service Reservoir (OHSR) The capacity of over head service
reservoir, in the case of canal based water supply scheme shall also be fixed considering the
pumping schedule and draft pattern as in the case of Tubewell based schemes.
8.5.2 Disinfections: Chlorination with Chlorine gas using a vacuum chlorinator is a
very effective disinfections process for water treatment. However, the availability of gaseous
chlorine and maintenance of the chlorinator are the constraints to adopt this type of
chlorination practice of the rural water supply system. Hence, addition of bleaching powder is
usually practiced for disinfections of rural water supplies. Availability of good quality
bleaching powder with the required amount of available chlorine and prompt addition of
bleaching powder in adequate quantity and at required interval is also essential. In order to
achieve maximum destruction of bacteria a minimum contact period of 30 minutes between
the bleaching powder solution and the water is required. If the bleaching powder is added in
the OHSR the addition has to be done before stopping of pumps since the turbulence due to
pumping will enable mixing of bleaching powder solution and the incoming water. However,
the distribution system outlet must be opened only after a minimum period of 30 minutes after
stoppage of pumping.
Normally the bleaching powder contains 30 to 35 % of chlorine when it is fresh. Since
bleaching powder losses its chlorine content with time, it is desirable to assume that bleaching
powder contains 25% of chlorine while determining dosage of bleaching powder. Hence, in
order to give a chlorine dosage of 1mg/ltr,: Bleaching powder of 4mg Per liter is to be dosed.
After addition of the bleaching powder the residual chlorine in the OHSR water has to be
about 1mg for liter to ensure minimum residual chlorine of 0.2 –0.3 mg/ltr at the consumption
point. Any abnormal changes in the residual chlorine level or absence of residual chlorine will
indicate the contamination of water. A chloroscope shall be used to check the residual chlorine
content. Chloroscope consists of a colour comparator kit. Orthotoladine solution is used to
check the residual chlorine content. Chloroscope consists of a colour comparator kit.
Orthotoladine solution is used as reagent in finding residual chlorine. A sample of water is
taken in a test tube and a few drops of the reagent is added to the water and shaken. If residual
chlorine is present, the water in the test tube will turn to yellow. The concentration of residual
chlorine is indicated by the intensity of the yellow colour i.e. the deeper the yellow; higher
will be concentration of residual chlorine. The comparator kit provides accurate comparison of
colours and hence assess quantity of residual chlorine. Chlorination shall be done by using
metering Pumps based on Teflon diaphragms to ensure accurate dosage and long life. The
storage tank shall be FRP lined and body of the pump shall Glass reinforced plastic to avoid
corrosion. Ceramic balls shall be used as valves and no MS ball shall be used. As cost of silver
is high therefore instead of silver ionization unit dosatron unit may be used for disinfecting
93
water. It is non electricity based unit, hence saves electricity charges. Difference between
Dosatron and Electric Pumps is given in Annexure – F.
8.6 Priority levels for Technical Options for water quality: The priority level for
treatment of various constituents like fluorides, nitrates, total dissolve solids, iron and coliform
bacteria shall be as below:
94
CHAPTER –9
ASSESSMENT OF EXISTING SYSTEM
In Punjab most of the villages are provided with water supply in one form or the other.
The technology options for these schemes varies from simple hand pump, mini water supply
scheme, piped water supply schemes with ground water source and a few piped water supply
schemes with surface water source. These schemes have been executed by the WSSD Punjab
and have been handed over to the respective GP‟s and O&M. Due to constrains of funds the
GPs are not able to pay even the electricity bills and are unable to maintain the schemes
optimally. In some instances lack of skilled labour is also contributing to this situation. Hence
most of the rural water supply systems are not functional or working below their designed
capacity. Failure of sources, water quality problems, leaking pipelines & ESR, inefficient
motors coupled with lack of management support are some of the common problems. The
community is not paying the user charges towards the water consumed by them and the GP
has no independent source of income. In view of this, there is a need to assess the status of the
existing water supply system and to estimate the rehabilitation needs so that the systems will
become fully functional.
Rehabilitation works have to be identified so as to facilitate integration of the proposed
water supply schemes with the existing water supply system. Rehabilitation works can be
divided into immediate needs and long term needs. In the immediate needs, there is no major
investment but small additions and proper management may certainly revive the schemes.
Some of the works that could be included shall be
a) Provision of required type of Valves at appropriate places.
b) Rectification of leakages in pumps, pipelines and reservoirs.
c) Immediate repairs to pumps and motors.
d) Effective supervision.
e) Establishing independent feeder main lines and disconnection of service
connections on main lines to ensure equitable water distribution.
In the long term needs, additional investments are made so as to upgrade the existing
system to the desired level. Some of the works that could be included shall be
96
contain all items in the DSR, relevant technical specifications and drawings shall be
provided for all items in BOQ.
97
S. No. Requirement/Activity Yes/No Remarks
vii) House connections to all households with saddle piece, MDPE
/GI pipe & consumer meter.
viii) O&M cost.
ix) Separate estimate for consumer and bulk meters
x) Separate estimate for simple SCADA (for large MV Scheme)
Enclosures to DSR
i) Population calculations
iii) water quality analysis report from proposed source
iv) drawings for all components
v) rate analysis worked out for all items
vi) detailed estimates for all components
vii) Cost estimates for all components
viii) Per capita cost worked out
ix) Cost of production of water Rs / KL
98
CHAPTER –10
SEWERAGE SYSTEM
10.1 Present scenario of wastewater disposal :
The wastewater generated from various household activities in villages overflows into
open surface drains and is ultimately disposed into ponds, thus making them highly polluted
cesspools. Cow Dung also contributes to high BOD in these ponds. Seepage from pit latrines
may also affect the underground water. This is leading to a serious health risk where villagers
are drinking water from hand pumps located near soak pits or ponds, besides frequent
occurrence of water borne epidemics like cholera, hepatitis, malaria, diarrhea etc.
The World Bank has estimated that water-and excreta related diseases in 1979 were
responsible for loss of around 400 billion working days in Africa, Asia & Latin America
which amounted to US$ 200 billion. Hence investments in improved water supplies and
improved sanitation can bring benefits not only to individuals, but also to National economics.
Governments need, therefore, to invest in their water supply and sanitation sector. If they do
not, their economies will not develop as productively as possible, and people will continue, in
the words of the Barbara Ward- to defecate themselves to death.
Keeping the above facts in view, International agencies in the field carried out
extensive R & D for developing low cost water supply & sanitation technologies during the
International drinking water supply and sanitation decade (1981-1990) and now safe water
2000.
Realizing the consequences of excreta related disease transmission in rural areas, Pb.
Govt. on its own in 2001 took initiatives in developing and demonstrating workable and low
cost sewerage system and sewage treatment technologies. As per the learnings during
implementation of 97 schemes in PRWSS-I, it has been experienced that beneficiaries are
hesitant to construct individual intercepting chambers. Case study of few schemes also
indicate that water supply even if designed at 70 lpcd, actual supply availability vary from 120
to 150 lpcd which also include individual sources. Therefore, possibility of conventional
sewer may also be considered.
Planning and Implementation of LWM Works by GP/ Village: Planning and choice of
technology option will be decided by the Gram Sabha or GP. Provision of land for community
sanitation facilities will be provided by the GP. Implementation of all environmental sanitation
works will be done by GP with community participation and technical support of ZP. Funds
can be accessed from Swachh Bharat.
Preparation of Village wide Master Plan: A Gram Panchayat (GP)/village wide master plan
for LWM is to be prepared by the GP with the help of DWSS/rural development/ zilla
parishad (ZP) officers/consultants along with community consultation and, implemented by
the GPs. The LWM Plan will include environmental sanitation facilities (both on onsite and
offsite).
99
Scope of Work of LWM Plan: The scope of work of “preparation of LWM Plan in a
village/GP for creating onsite and offsite facilities as appropriate for liquid waste
management” is described below:
i. Conducting detailed engineering survey (by Total Station Method) along the roads of
entire GP and prepare a base road map with levels, lengths and widths of the various
roads and lanes.
ii. Total station survey need not be used for preparing the plans for small villages.
iii. After the plan is ready conduct a household community survey
iv. First item in survey is to find whether the house has a toilet or whether there is space
for constructing a toilet.
v. In case the house has no space for toilet find a common place in the village for a group
toilet.
vi. Depending on service levels of water supply, soil percolation rates and ground water
table, decide whether a household soak pit is a feasible option for sullage disposal and
whether the house has space for a soak pit.
vii. Assess the status of open drains in the village; whether they are clogged with solid
waste and silt, and whether the disposal is happening or whether the sullage is getting
stagnated. If open drains are misused examine feasibility of pipes for carrying sullage..
( see viii) below.
viii. If provision of soak pits is not a feasible option, examine feasibility and propose small
bore(pipes) sewerage system in place of open drains for collection and disposal of
sullage after treatment. Piped sewers are preferred for larger villages.
ix. Assess scope and availability of space for toilets in anganwadis ad schools.
Community sanitary complexes.
Small bore /Solid free Sewerage system: Since all households are provided with toilets, only
liquid waste will be generated for which huge open drains are not required. If the community
awareness is created on proper use of the facilities, small bore pipe sewers are likely to be a
better option for conveyance of sullage. Sullage from Households is collected via 100 mm
feeder line and sewer lines are laid at slope (between one in 167 to 200) and Manholes are
kept at 15 or 30 m. About 100 households are connected to one 100 mm dia PVC feeder lines,
Houses connect to the feeder lines through small concrete collection or inspection boxes of
about 40 cms in diameter. Since no vehicular traffic passes over the feeder line in the lanes, it
can be laid at shallow depth, reducing the amount of trenching and number of manholes.
Feeder lines are laid at a minimum depth of 30 cms to 40 cms and rarely exceed one meter in
depth. When these lines cross the roads they are protected from vehicle loads by appropriate
encasing.
Sullage Treatment: (i) Effluent is usually collected outside the GP into any existing pond
where it can be treated by oxidation pond. (ii) Alternatively the effluent can be aligned along
the borrow area of the approach road and treated through suitable treatment technology.
100
Contents of a LWM Plan: The LWM plan will contain following:
i. GP Base road map with levels and lengths and widths of roads and existing nature of
paving
ii. Households with toilets and without toilets with those with space and without space for
toilets. Space for group toilets, community biogas and waste stabilization ponds.
iii. GP base road map with proposed layout of small bore sewers with manholes,
inspection boxes
iv. Number of Households requiring soak pits
Preparation of drawings and cost estimates for (a) individuals , Households, Soak pits and (b)
for the community environmental sanitation infrastructure including water supply for
community sanitation complex, group toilets, Toilets in anganwadis and schools and,
Providing small bore sewers, Providing sullage treatment facility with any simple technology.
Cost estimates will be based on latest Schedule of rates.
10.2 What is small bore/ Solid free sewerage system :
Solid free sewerage system is a cost effective sustainable technology which is designed
to receive only the liquid portion of house hold waste water and troublesome solids are
retained in intercepting chamber installed up stream of every house connection to sewer. As
such, the sewer requires less velocity for flow of waste water and reduced flow requirements
(less than 50% of conventional system).
In the Solid free sewerage system, PVC pipes of minimum 100mm o/d should be
adopted. To prevent choking of sewerage system, inspection chambers are provided in each
individual house to retain the solids and partially decompose the organic matter. Even the
animal excreta are also contained into inspection chamber after preliminary treatment. Thus,
there would be no overflow of waste waters onto streets. A novel syphonic system is
incorporated for automatic flushing of sewer at regular intervals. In this system, the
conventional man holes have been omitted which are normally never operated and are rather a
source of dumping of garbage. Intercepting chambers are required to be cleaned once in 3-5
years using trolley mounted vacuum pumps. Instead cleanouts are provided for flushing and
cleaning of sewerage, if needed, in case of unforeseen choking of sewerage. These cleanouts
are again buried below ground level to avoid tampering. These features along-with the relative
imperviousness of HDPE / PVC pipes totally foreclose any possibility of infiltration of ground
water or ex-filtration of sewage contaminating the surrounding strata. Benefits of the
technology have been reported as:
The open drains have been eliminated and the streets are absolutely dry and clean.
No embarrassment to ladies and children due to open defecation.
Distinct hygienic quality of life visible even in weaker section.
People have become aware about the benefits of safe wastewater disposal.
Minimum Operation & Maintenance cost.
10.3 TREATMENT TECHNOLOGIES :
The waste waters are ultimately collected at the last point and pumped for subsequent
treatment through various low-cost technologies which do not require any mechanical parts
and minimal power. Various technologies for treatment of sewage / waste water are enlisted
as:
101
i) Stabilization Ponds.
ii) Duckweed Ponds.
iii) Treatment by Forestry/ Tree Plantation (Karnal Technology).
iv) Root Zone Technology/ Artificial Wetlands
v) Aerated Lagoons
vi) Decentralized Wastewater Treatment System (DEWATS)
vii) Soil Biotechnology (SBT)
Stabilization ponds are open flow through basins, specifically designed and
constructed to treat sewage and wastewater. These provide long detention periods extending
from a few to several days in which, organic matter in the waste is stabilized through a
symbiotic relationship between bacteria and algae. The facultative ponds are best suited and
most commonly used for treatment of sewage. In these ponds, at the surface, aerobic
conditions prevail while there are anaerobic conditions at the bottom. Sewage organics are
stabilized by both aerobic and anaerobic reactions. For further treatment of microbial
pollution, maturation ponds as per characteristics of the sewage & required level of treatment
are also provided, which are similar to facultative ponds.
Stabilization pond is comparatively simple and easy to construct. It does not require
skilled operation and is easy to maintain. It gives consistently good and high level of
performance in terms of pathogens removal and reliability, which is not attained by other
process. Thus these are most suitable for treatment of sewage for the rural areas as it requires
practically no maintenance and involves no moving parts. Moreover these are universally
accepted and have stood the test of time.
10.3.2 Duckweed Pond Technology:
Duckweed pond is an earthen pond or a lined pond where duckweed plants are grown.
These duckweeds cover the entire water surface and eliminate growth of algae and also
suppress the odours and eliminate mosquito breeding. In these ponds, both anaerobic reactions
and activity of duckweed growth are responsible for treatment of sewage and wastewater.
Duckweed is still at development stage and is situational specific and recommended to be used
depending upon the specific situation.
10.3.3 Treatment by Tree Plantation/ Forestry (KARNAL TECHNOLOGY):
In this method, nutrient potential of raw sewage and wastewater is utilized for forestry.
Suitable ridges and furrows are made on the land and tree species such as eucalyptus and
poplar etc, which can grow fast, transp-evaporate huge quantity of sewage and at the same
time are able to withstand high moisture content in the roots are planted on the ridges. Each
tree acts as a small bio-pump absorbing liquid through the surrounding soil and releasing it to
the environment through transpiration. Nutrients like NPK and micronutrients are supplied to
soil and plants, thus building soil fertility. The amount of sewage to be applied depends upon
type of plant, climatic conditions, soil texture and quality of effluent. Sewage treatment by tree
plantation is situational specific and recommended to be used depending upon the specific
situation.”
102
10.3.4 Root Zone Technology/ Wet Land System (RZ):
This is basically a manmade wetland, where waste water is kept at or above the soil
surface for enough time during the year to maintain saturated conditions and appropriate
vegetation like reeds. Reeds have an oxygen transport system from the leaves to the roots that
permits the roots to survive in the anoxic conditions prevailing in a wetland. The oxygen
supplied to the hollow roots called rhizomes is available to the aerobic bacteria growing in
wastewater. Wastewater is pumped directly into the upper end of the reed bed surrounded by
impermeable walls. The reed bed may require considerable time, several months to grow and
develop root system to achieve full treatment efficiency. This is a natural process of treatment
of effluents, economical and efficient at places where wasteland is available. On the basis of
experiments in Europe, USA and India, it has been found that by adopting this process
pollution load can be reduced by 80 to 90%.
Like duck weed technology, root zone technology in India is still at development stage
and is situational specific and recommended to be used depending upon the specific situation.”
10.3.5 Aerated Lagoons (AL):
Aerated lagoons are simple earthen basins, which act as a settling cum aeration basins
in which artificial aeration replaces algal oxygenations. It has inlet pipe submerged in liquid to
avoid odour and short-circuiting. Outlet at the other end is sufficiently wide to enable the
wastewater to flow through while aeration is provided to stabilize the organic matter. Scum
baffle is also provided at outlet. These are normally of facultative type in which some solids
may leave with the effluent stream and some settle down in the lagoon since aeration power
input is just enough for oxygenation. Lower part of such lagoons is anaerobic, while the upper
layers are aerobic. It is adopted at places where land space is limited, sufficient power is
available and enlargement or re-location is possible in the near future.
Aerated lagoons are not natural processes and require artificial aeration, which
involves regular power supply, moving parts and strict supervision and attendance. As such,
these are considered only in cases where electric power supply is assured.
10.3.6 Decentralized Wastewater Treatment System (DEWATS) :
These are locally organized systems that are typically comprised of a settler, anaerobic baffle
tank, filter beds of gravel and sand and an open pond. DEWATS applications are based on
four basic treatment modules, which are combined according to specific requirements
including post treatment methods in the shape of reed beds and ponds as below:-
Pretreatment & sedimentation in settlement tank or in a septic tank
Secondary anaerobic treatment in baffled reactors
Anaerobic/aerobic treatment in reed beds
Aerobic treatment in ponds
An indicative flow diagram is given below:-
103
Main DEWATS modules for physical and biological wastewater treatment:
1. Settler 2. Anaerobic Baffled Reactor 3. Anaerobic Filter 4. Planted Gravel Filter
Primary treatment is carried out in a septic tank in which liquid part is separated from solid
matter. Settled sludge gets partially stabilized by anaerobic digestion, whereas dissolved and
suspended matter leaves the tank untreated. BOD removal is in the range of 35-40%.
Secondary Treatment is provided in the baffled reactor wherein several tanks (upflow
chambers) are built in a series to digest degradable substance. Baffle Walls direct the water
stream between chambers from top to bottom and up again. During the process fresh influent
gets mixed and inoculated for digestion with active blanket deposit of suspended particles and
microorganism occurring naturally at bottom of each chamber and because of physical
separation various organism are at various stages allowing high treatment efficiency. At the
end of chamber, an upflow anaerobic filter is provided to improve further the efficiency of the
reactor. Tertiary Treatment is provided through a reed bed with horizontal filter. Treated
effluent, as obtained from the reed beds, can be finally treated in polishing ponds where it gets
exposed to atmosphere and wherein both aerobic degradation and pathogen removal takes
places. Fish farming can be carried out in case of large and low loaded polishing ponds.
The treatment process is simple and desirable with high treatment efficiency if properly
constructed and maintained. A few plants have been set up at various locations in the country.
DEWATS system has been practiced and promoted by Centre for Scientific Research (CSR),
Auroville , Tamil Nadu. CSR operates about 50 plants of capacities upto 150 persons. Treated
effluent is used for recycling
A 30 cum capacity plant has been constructed within campus of an Engineering College in
Ghaziabad, UP.
Vigyan Vijay Foundation has established a 40 cum capacity plant based on DEWATS
technology in Delhi.
Performance records of these plants as available shows BOD & COD reduction by 80% and
Faecal Coliform reduction by 85%. The technology though is with minimal power
requirement is highly land intensive, requirement is about 6 Ha/MLD and therefore, suitable
for very small capacity applications. The plants have to be added with appropriate disinfection
arrangements to make treated effluent safe for discharging into environment.
0.3.7 Soil Biotechnology :
104
Soil Biotechnology (SBT) is a bioconversion process where fundamental reactions of nature
namely respiration, photosynthesis, mineral weathering take place in a media housing micro
and macro organisms which bring about the desired purification. CAMUS-SBT or CSBT is an
advanced and superior version of SBT which uses only local supplies and is an oxygen
supplying biological engine and so the process can treat all types of water - domestic,
municipal and industrial. CAMUS -SBT uses the ecology of soil type media and biological
reactions within a constructed bioreactor to treat waste water.
Features of the technology
● No external aeration
● Low power consumption
● All green process
● No moving parts
● No bio-sludge formation
● Efficient removal of pollution
● Garden like ambience
● One time media installation
● Long life
● Unskilled personnel sufficient
to operation
● Low space footprint via
designs for below roads, in
traffic islands, boundary wall, above settling and storage tanks.
The technology is covered by two US patents (patent no 6890438 B2 dated 5 May 2005 and
7604742 B2 dated 20 October 2009) and 2 Indian patents (patent no - 203744 and 203425) all
assigned to IIT Bombay.
Figure 10.1
Figure 10.1 depicts Typical Process Flow for CAMUS-SBT Sewage to Water Recycling System. Single Stage 1) Raw
sewage is collected in Raw Water Tank (RWT) after initial screening and settling. 2) The raw sewage is pumped on top
of a CAMUS-SBT Bio Reactor where it percolates through a patented media.
The treated water is collected at the bottom of the Bio Reactor and stored in a Treated Water
Tank (TWT). Any further purification if required is achieved by recycling the treated water
through the BioReactor as shown. Incase as per site a two stage design is required then an
intermediate sump is required. Some other features are summarised below:
105
SBT/CAMUS-SBT allows user start-stop mode of operation and the plant can be run
in intermittent mode, batch mode and continuous mode as per site conditions allowing
100% mission availability under varying conditions.
SBT/CAMUS-SBT can easily handle 150% peak loads for a few days by increasing
running times as the situation demands.
107
water body and therefore result in a
clear effluent with low TSS content.
The presence of duckweed cover has
been reported to decrease the
development of mosquitoes in the
water body.
It has been reported to have positive
effect on odour control when
covering a wastewater body.
Harvested duckweed may have an
easy local market for chicken, cattle
or fish feed.
With utilization for aquaculture, this
process is capable of generating
revenue.
No moving parts and no energy
requirement except that requires for
pumping station.
BOD reduction is 80-90%
Duckweed based treatment system is
suitable only for waste water having
lower organic strength.
Duckweeds are sensitive plants,
which are affected by weather
conditions. Cold regions are not
suitable for the duckweed based
treatment system.
Duckweeds are sensitive to organic
shock loads.
Duckweeds can be easily swept off
from water surface to one side by
wind.
Regular attendance and care is
required.
Microbial pollution reduction is
rarely within safe limits.
3. Tree Merits : Where treatment site is
Plantation Relatively cheaper involving less available away from the
capital & recurring cost. population.
Economically viable as it generates Fertility of waste land is
monetary returns from the sale of required to be improved.
trees. It is appropriate for the rural
Restores environment. areas where bio mass forest
Highly skilled manpower is not can be raised.
required. It is applicable for villages
Suitable for imparting fertility to less where sufficient land is
fertile land. available.
No power requirement and moving
parts.
Demerits:
108
The technology is not applicable
where ground water table is high (in
depth)
Improper application of sewage to
the forestry may cause soil sickness.
Possibility of ground water pollution
during non irrigation period.
Large chunk of land is required.
Difficulty in controlling odour, fly
and mosquito breeding problems.
4. Root Zone Merits: Where swamp (wetlands) is
No requirement of energy and available nearby.
mechanical equipment for aeration. Where water table is high and
Self-regeneration of reed bed and is likely to create swamp
virtually maintenance free. during
System can prove natural habitat for
fauna.
Demerits:
Large land areas are required. rainy season.
Difficulty in controlling fly and
mosquito breeding problem.
Microbial pollution reduction is rarely
within safe limits.
109
6. Filtration & Merits: Where skilled and trained
Polishing Land requirement is medium. manpower is available.
Ponds Leads to reasonable microbial Availability of land is
pollution reduction if used with restricted.
polishing pond or UV radiation or
chlorination.
Demerits:
Regular attendance is required.
Frequent washing is required.
In order to economise the cost of construction of the household toilets and drains it is
necessary to prepare the plans and estimates using locally available material such as
bricks and stones for construction of toilets, stone slabs for lining for drains, etc, to the
maximum possible extent. Locally available artisans, masons, plumbers, unskilled
made materials such as CI pipes, PVC pipes, FRP/ceramie water closet to be procured.
11.2 Twin Pit Pour Flush Latrine (TPPFL)
Twin pit pour flush toilets to the rural communities, since these toilets require less water and
also do not pollute the ground water table. Further these toilets are economical and easy to
construct and maintain.
TPPFL consists of a squatting pan, a trap with water seal, footrests, a connecting drain and
two leach pits. The principle is that small quantity of water is used for flushing the toilet so
that this water leaches easily into the surrounding soil and leaving the solids alone for
digestion.
The squatting pan is of special design with steep bottom shape bottom slope 25-28o
with a trap having 20 mm water seal set on a cement concrete floor. The slope of the toilet
pan is such that pouring small quantity of water (about 1.5 to 2 litres of water per use) can
flush human excreta.
The squatting pan is connected to twin leach pits through a trap and a pipe or covered drain.
The flushed contents from the squatting pan flows and fills the connected leach pit. When one
pit is full, the excreta are directed to the second pit. The filled up pit can be conveniently
emptied after
1 ½ to 2 years, when most of the pathogens die off. The sludge can be safely used as a
manure. Thus the two pits can be used alternately and continuously. A typical twin-pit pour
flush water seal latrine is shown in Fig. 10 a and 10 b (of drawings).
Pour-flush water seal latrine is a very satisfactory and hygienic sanitation system and hence it
can be located yards since the water seal prevents odour and insect nuisance.
111
11.2.1 TPPFL pits in Water Logged, Flood Prone and High Sub-soil Water Areas and
Rocky strata.
Pits in Water Logged, Flood Prone and High Sub-soil Water Areas
In high sub-soil, water logged of flood prone areas, the pits should be raised above the
ground level to a height such that the invert of the incoming drains/pipes is just before
the likely flood water or sub-soil water level. Raising the pipes will necessitate raising
the latrine floor also.
In pits located in water logged or flood prone areas, earth should be filled and well
compacted all around the pits in 1000mm width and up to the top. It is not necessary to
raise the pits by more than 300 mm above the plinth of the house because if water rises
above the plinth, the residents will anyway vacate the house.
In high sub-soil water areas, about 300mm filling all around the pits may be done
depending on site conditions.
In these situations, the pits should be designed as wet pits, taking into consideration the
infiltration rate of the type of soil.
Where circular pits of standard sizes cannot be constructed due to space constraint,
deeper pits with smaller diameter (not less than 750 mm), or combined oval, square or
112
rectangular pits divided into two equal compartments by a partition wall, may be
provided. In case of combined pits, the partition wall, as well as the adjoining side wall
up to 225 mm width, should not have any holes. The partition wall should be 225 mm
deeper than the pit lining. Both faces of the partition wall should be plastered in
cement mortar 1:6.
To ensure that the risk of polluting ground water and drinking water sources is
minimal, the following safeguards should be taken while locating the pits :
a. Drinking water should be obtained from another source or from the same
aquifer but at a point beyond the reach of any faecal pollution from the
leach pits.
b. If the soil is fine (effective size 0.2mm or less), the pits can be located at a
minimum distance of 3m from the drinking water sources, provided the
maximum ground water level throughout the year is 2m or more below the
pit bottom (low water table). If the water table is higher, i.e. less than 2m
below the pit bottom, the safe distance should be increased to 10m.
c. If the soil is coarse (effective size more that 0.2mm), the same safe
distances as specified above can be maintained by providing a 500 mm
thick sand envelope, of fine sand of 0.2 mm effective size, all around the
pit, and sealing the bottom of the pit with an impervious material such as
puddle clay, a plastic sheet, lean cement concrete, or cement stabilized soil.
d. If the pits are located under a footpath or a road, or if a water supply main
is within a distance of 3m from the pits, the invert level of the pipes or
drains connecting the leach pits should be kept below the level of the pipes
or drains connecting the leach pits should be kept below the level of the
water main, or 1m below the ground level. If this is not possible due to site
considerations, the joints of the water main should be encased in concrete.
113
Diversion of Flow from One Pit to Another
When the filled pit is allowed to rest for a minimum of one and a half years, the
pit contents are completely digested and free of foul smell. The pit can then be
safely emptied manually, without being hazardous to health, by the
householder himself or through the local authority or a private agency.
However, in the case of combined pits and pits located in water logged and
high sub-soil water areas, de-sludging of pits should be done carefully because
the sludge might not be completely safe and dry to handle due to travel of
pathogents from the pit in use to the pit to be desludged. After the pit is
emptied, the pit cover should be placed in position and the joint made air tight.
The humus collected has rich manure value and is a good soil conditioner. The
humus from dry pits can be used be directly either in the kitchen garden or the
fields, but from wet pits it can be used only when it is sun dried.
Do‟s and Donot‟s
114
- When the pit in use is full, divert the flow to the second pit as discussed on
page 11.2.2
- If the trap gets choked, rodding should be done from the pan side as well as
from the rear side by means of a split bamboo stick, after removing the cover of
the drain or junction chamber.
- Care should be taken when desludging the pits located in water logged or high
sub soil water areas and in the case of combined pits, as the humus may not be
safe for handling.
DON‟T‟s
During construction, one should check whether the following conditions have been
met :
- The depth of the pit below the invert level of connecting pipes or drain shall be as
given in relevant drawings.
- If the maximum ground water level throughout the year remains 2m or more below
the pit bottom, and if the soil at site is fine (effective size 0.2 mm or less), the pits
have been located maintaining a minimum distance of 3 m from the drinking water
sources. If the water table is higher, a minimum 10 m distance be kept to minimize
the chances of pollution.
- If the soil at the site is coarse (effective size more than 0.2mm), a 500 mm thick
envelope
of fine sand of (0.2 mm effective size) has been provided all around the pit, its
bottom
sealed, it is located at a minimum distance of 3 m if ground water table is higher, a
minimum distance of 10 m has been kept to prevent pollution of drinking water
sources.
115
- The pit size conforms to be geological and hydrogeological conditions and the likely
number of users, and adequate leaching area has been provided, if necessary, by back
filling for proper infiltration of incoming liquid in to the pits. In cases where the
foundation is very close to the pits, holes have not been provided in the portion of
lining facing the foundation, and the leaching area has been increased suitably.
- The minimum distance between the two pits shall be equal to the effective depth
(depth of the pit below the invert of incoming pipe or drain ) of the pits.
- The pits shall not be located in a depression where water may stagnate over the pits
or in a drainage line which allows the flow of rain water over the pits.
- The bottom of the leach pit has been left in a natural condition except where it is
necessary to seal it to prevent pollution
- The RCC cover is as per designs.
- The top of the pit cover is about 50 mm above the natural ground level and the
earth fill is well compacted all around the cover sloping to avoid a step being
formed.
- The drain is “U” shaped, cross-sectionally and its inner surface is smooth.
- Drains with benching have been properly provided in the junction chamber to
divert the flow to one of the two pits.
- A minimum gradient of 1:15 has been provided in the connecting drains or
pipes.
The mouth of the drains or pipe is projecting nearly 75 mm past the pit lining in
the pits.
- The flow has been restricted to one pit by blocking the mouth of one of the
drains or pipes.
- The materials used are of the quality specified in the design, or relevant
standard specifications and the workmanship is good.
- The specifications laid down have been followed and the work has been
finished nearly.
- The floor surface is smooth and sloping slightly towards the pan.
- The foot-rests have been fixed at the proper place and at an angle, as in the
drawing
- 50 mm wide holes (honey combing) have been provided in the pit lining in
alternate layers up to the invert of the pipe or drain, and the lining above is in
solid brick work (no holes). If the soil is sandy, or if a sand envelope has been
provided, or there are chances of damage by field rats, the width of the holes
has been reduced to 12 to 15 mm. If the foundation of the building is close to
the pits, holes have not been provided in the portion of lining facing the
foundation. In cement concrete ring lining, rings below the invent of pipe or
drains should have 50 mm circular holes suggested about 200 mm apart.
- The covers over the pits, drains and junction chamber have been placed
properly.
- The pan and trap used are of a design specified for pour flush and these have
been fixed properly so as to provide a 20 mm waterseal, and that the joint is
water tight and the top of the pan is flush with the latrine floor.
116
- No Vent pipe has been provided.
- A well ventilated superstructure has been provided to enable use of the latrine.
- All surplus material have been removed and the site cleared and dressed.
- The users have been educated on the use and maintenance of PF latrines.
Materials :
The squatting pan can be of ceramic, glass fibre reinforced plastic (GRP), high density
polyethylene (HDPE) or polyvinyl chloride(PVC) polypropylene (PP), cement mosaic
or even concrete superstructure. However, the ceramic pans are favored in this project
due to the better non-sticking & non-staining properties.
Where individuals do not have adequate space a group of TPPFL toilets can be
constructed in a common area owned by individuals and used exclusively by the
owners duly providing locking arrangement. In institutions such as schools, primary
health centers etc., similar group of TPPFL toilets can be provided. A typical sketch of
an institutional latrine is given in Fig 11 (of drawings).
Soak pits are used dispose the effluents of the drain into ground where cannot
discharge the effluents in a natural stream. These are ideally suitable for the regions
where the terrain is flat and no nallah is available near the village. Normally, soak pits
are provided next to stand posts, hand pumps and washing platforms so that
wastewater does not get accumulated in the vicinity.
In general, the disposal of effluent may be either underground or over ground.
Normally, underground disposal either in the form of soak pits or dispersion trenches
is practiced. Satisfactory disposal depends on porosity and percolation characteristics
of the soil.
When black cotton soil is encountered, we have to conduct percolation field test on the
soil near the proposed disposal site. Normally permeability value for the black cotton
soil will be very less. This Value has to be taken for designing the disposal system.
Most of the time it is desirable to adopt a battery of dispersion trenches depending on
the rate of percolation obtained from the field test and providing larger length of
dispersion trenches.
The procedure to be followed to arrive at the size of the soak pit depending upon the
soil conditions for a known effluent quantity is as follows:
117
The important parameter to be determined is the rate of percolation of filter media. For
this, the following procedure shall be adopted. This is most important in clayey soils,
which are relatively impervious.
Drill a hole of dia 300 mm to the required depth of soak pit / dispersion trench at the
site chosen for constructing the soak pit. Remove all loose materials from the hole and
fill up coarse sand or fine gravel to 50 mm depth to prevent scouring of the bottom.
Fill up water to a depth of 300 mm in the hole and allow 24 hour duration soil to get
saturated with water by pouring water on subsequent days till some water remains in
the tested hole after the overnight swelling period. Now top up the water to get a depth
of 150 mm of water over the sand in the hole. Now the hole is ready for carrying the
test.
From a fixed reference point, measure the drop in water at 30 mm intervals for 4 hrs. If
necessary, water can be refilled to 150 mm depth over the gravel. The drop in water
level that occurs during the final 30 mm period shall be used to calculate the
percolation rate.
Note : In case of sandy soils, water seeps away in less than 30 minutes. Hence, the
time interval between measurement may be taken as 10 minutes and the test run
for 1 hr. The drop that occurs during the final 10 minutes shall be used to
calculate the percolation rate.
Based on the final drop during the period of 30 minutes (for sandy soils, 10 minutes)
the time in minutes required for water to fall by 25 mm shall be calculated which is the
percolation rate. A typical percolation chart is illustrated in Fit 34.
For example, we observe that during the 30 minutes period, drop in water level is
found to be 100mm.
From the chart-27, for the percolation rate of 7.5 minutes, the maximum rate of
effluent application =751/sq.m/day
118
Hence a soak pit or dispersion trench of surface area 10 sq.m shall be provided.
These are drains lined with brickwork and concrete.Even though lining is
costly, they are functional and easy to maintain. Preferably local available
material is be used. Type of drain are Punjab standard drains of type I, II, III &
IV according to the discharge and depth.
Layout of drains :
Drains have to be provided in the lanes and then off to the disposal point.
Hence survey of the internal lanes in a village is the first step to decide the
layout of the drains. During the survey the available width and the length of
each lane and the gradient are also noted. The drains provided under the project
will closely follow the network of lanes. In the absence of sufficient space for
drains on either side of the lane, the paved surface itself has to be designed to
act as a drain for storm water. The center of the lane will act as drain portion.
This prevents water entering the sills of the houses.
The layout of drains has to be suitable to dispose the sullage/storm water in to
natural drainage course. Generally, slope of terrain has to be followed and
adopted so that the drains to be provided will have uniform depth. Also, it has
to be ensured that there is no stagnation of water, which may result in a
breeding of mosquitoes causing health hazard. Hence where there is no natural
slope of terrain minimum slope of 1 in 240 may be provided for 200 mm wide
drain and 1 in 375 for a drain of 250 mm wide. Whereever possible the drains
may be lead to rainwater harvesting structures so that general ground water
table is recharged and increase the sustainable yield of wells in the vicinity.
119
CHAPTER-12
OPERATION AND MAINTENANCE OF WATER SUPPLY
SCHEMES
The infrastructure created in any scheme should satisfactorily last for the entire design
period of the project. To ensure this, the various components of the project need
maintenance during the project period for deriving maximum services out of them.
Without planning both technically and financially for the proper maintenance and
operation of the systems, these will not function correctly after commissioning and
the anticipated benefits will not be realised. In rural areas of developing countries, a
key to ensuring proper O & M is the participation of community from the conceptual
stages of project and their performances been taken fully and seriously into
consideration. Therefore user should know the most likely cost of O & M. The
operation and Maintenance cost of a scheme depends on the capital cost, fixed cost
and variable cost. For O&M of water supply schemes CPHEEO Manual on O&M of
water supply systems could be referred.
The various maintenance works for a water supply scheme are listed as
below:
For re-commissioning
i) The filter after cleaning allow water from under side so that dissolved gas or air
entrapped. When bed was exposed to escape and also to provide water cushion so
that when inlet valve is opened, sand bed is not isturbed.
ii) Opening inlet valve and ripening of filter is required. Dissolved oxygen (D.O) in
the treated water should not be less than 3 mg/lt. If D.O. is less than 3 mg/lt then re-
circulate the water treated through cascade aerator to increase the D.O. level in the
effluent.
iii) After several years of operation-by means of cleaning, sand depth may reach
minimum. Part of this removed sand has to be replaced back while resanding.
iv) For replacing the old sand when removed while cleaning, if decided to be used
again, it should be washed immediately after taking out from the filter otherwise
sand will become septic due to oxygen demand by micro organisms present in sand.
(Ripening of filter = to allow the growth of micro organisms for purification
process,
time allowed to develop micro organism not less than 4 weeks.
(Range 2 – 8 weeks).
The pumping mains are often very long and generally laid along the road hence
damage to pipe may be caused due burst in pipe lines, tampering by unauthorized persons,
temperature variations, vehicular traffic, etc. Such unauthorized persons, temperature
variations, vehicular traffic, etc. Such damages should be observed and attended to
immediately. Ready made pipe sleeves, rubber sheets, and pipe clamps, etc shall be always
be kept in stock to stop the leakages in cracked pipes temporarily. If the pipes have
developed major cracks or severely damaged such pipes need to be replaced with good
ones.
The appurtenances in the piping main such as sluice valves, scour valves, air release
valves, etc shall be protected against tampering by unauthorized persons by always
closing the lid and locking the valve chambers.
Proper tools and implements as indicated above must be used. Usage of gum boots and
hand gloves are necessary in order to prevent contamination of the tank and also to prevent
skin irritation to workmen due to chlorine solution. Tank must be properly ventilated by
keeping all manholes in open position when the cleaning operation is in progress.
Un-trained workmen shall not be engaged for cleaning. Workmen shall not be permitted
into tank containing water more than 15 cm depth. Water level should be reduced prior to
allowing men inside to prevent accidents. Guard bars may be provided an outlet/scour
opening provided at the bottom and side walls of the tank may be checked frequently and
covers are to be replaced in position and locked.
A complete inspection of the distribution system and pumping mains shall be made once
and the survey must be made for leakages in the distribution system, sluice valves, fire
hydrants, scour and air valves. Underground leakages in a distribution system is generally
indicated by dampness. Flooding of water and extra growth of vegetation above the pipe
line at the place of leak. Leakage frequently occurs in house service ferrule connections. A
record shall be maintained to indicate the major repairs and leakages occurred with reasons
for the same which can be used to check unaccounted water loss in the system and to have
close check on these leakages prone points. Scour valves shall be operated and dirty water
let out once in a month. Gland packing in sluice valves should be replaced once in 3 to 6
months or more frequently depending on the leakage in gland, frequency of operation of
valve etc. Excess leakages in air valves shall be attended to in time.
In this project as the operation and maintenance of all the above units are to be managed
by the community without any financial contribution from the government it is essential to
educate the beneficiary community about the cost involved. The following example is
presented to arrive at the approximate cost and contribution by the beneficiary.
12.7. Maintenance of Structures , Lawns & Clean Environment :-
The main structures are pump chamber and staff quarter. The structures should be
painted after every 3 years. Besides the Sluice Valve haudies etc. should also be kept
123
clean. The leakage in S.V's are valves leads to standing water & causes in sanitary
conditions.
Pump operator is the most important functionary in the set up since it is he who is in
direct contact with the people all the time. The higher officers can maintain contact only
periodically. The pump operators primary responsibility is to run the machinery and keep
it in proper order. Besides he has to act a link between the consumers & the officials of the
department. The pump operator should maintain the following record :-
I) Log Book :- The log book should be maintained on a daily basis & incorporate the
following things
1. Date
2. Time of start of pumping set
3. Time of switching off
4. Total hours of pumping
5. Volt meter reading
6. Ampere meter reading
7. Depth gauge reading
8. Spring Level at time of start
9. Spring Level at time of switching off
10. Time taken to restore water level
11. Signature of P.O.
12. Signature of Inspecting Officer
13. Remarks Columns
If diesel engine or a generating set is used then an account of oil consumed should be
given. Besides entry should be made in log book about all the repair work.
The log book should contain the details of the machinery on the first page clearly
specifying the make, discharge capacity & head proper maintenance of log book helps in
keeping a check on the health of T/Well.
II) Complaint Register :- Complaint register should be properly maintained and all
the complaints should be entered chronologically along with the remedial measures taken.
The complaint should be self specific & the following should be clearly mentioned :-
1. Date of Complaint
2. Nature of Complaint
3. Time for which the complaint is witnessing it
4. Place of Complaint
5. Complainants name & address
6. Date on which noted by the field staff (if any)
7. Date of Compliance
8. Any Special Remarks
9. Remarks or Comments by the Senior Officers
124
The J.E. should check the complaint register at least once a week and
after solving the complaints problem must made on entry. If there is no
complaint recd. during a month, a certificate regarding this should be entered
by J.E/A/E.
III) Movement Register :- The P.O. should maintain a movement register.
So that the inspecting officers are able to check the attendance.
IV) Meeting register with Panchayats :- The P.O. should meet the village
Panchayat once a month & enter the minutes of meeting in the register. The J.E/A.E
should personally attend these meeting once in two months. This would help in proper co-
ordination between the department & the consumers.
The following inputs are assumed for the calculation of O & M cost.
GENERAL:
125
clear, brief details of the scheme for illustration of O & M cost is furnished in the
example below.
a) Requirement of Water
Population served by scheme (Present) - 1041 persons –2001 AD
Population served by scheme - 1500 persons
(Considering the growth at 20% per decade)
No. OF households at 5 person 1041/5 = 210 households
Per capita W/S - 55 Lpcd
Daily water requirement 1500 x 70 - 10,50,000 ltr/day
b) Source
Tube well (assuming) yield. - 32140 ltr/hour
Sustainable yield 60% to be considered
And safe yield should be decreased by 30 % to cover the decline in
discharge over a period of time .
i.e. 18,000 x 0.7x0.3 = 13,500.00
13500/3600 = 3.75 Lps
Pumping hours - 10hrs/day
13500 x 8 = 108000 ltr/day
No. of Tube wells = 105000/108000 = 0.97 or 1 No.
d) Distribution System
126
Pipe sizes –110 mm to 63 mm PVC 4 KSC
Supply through stand post for 50% at
1 No. Per 150 persons.
No. of stand post 1500/2 = 750/150 = 5 Nos.
2. COST OF SCHEME
b) Energy Charges :
127
c) Bleaching powder for disinfection
Chlorine dosage = 0.35 kg per 1,00,000 ltrs
Requirement per year = 105000 x 0.35 x 365 / 100000
= 134 kg @ Rs 20/kg Rs.
2680
Total = 146160
SAY : Rs 146000/-
The O & M Cost for water supply are to be explained to the users in various
meetings so that community can be aware of likely pattern of sharing of the
cost.
129
CHAPTER – 13
Construction Management
This chapter explains the actions to be taken during the progress of work. The water
source is established during planning stage. Based on the yield, the project planning, design,
estimate and tender action will be done. Construction sequences, procurement of materials,
construction management, specifications, permissible tolerances during construction phase are
elaborated.
13.1 Sequence of construction
a) Source
The source being selected during planning phase shall be flushed once again and the
yield ascertained for its dependability as regards Quality and Quality before commencement
of civil works. Procurement of pumps and rising main should take place only after above
actions are completed. Application to PSEB electric supply should be processed telescopically
so that by the time rising main and reservoirs are completed, electricity is (nearly) available.
b) Civil works.
The working levels shall be taken from the source point to service reservoir and
ascertained that the levels taken with that projected in the drawings proposed during planning
and preparation of DSR. If any variation is noticed the necessary action shall be taken to
redesign the raising main and pump machinery in accordance with the working levels now
obtained. As possibility of changes in location of OHSR are quite evident in villages for
reasons necessitating acquisition of land required for construction or change of sources. Civil
works construction will start once contract procurement process is over and work orders are
issued. Transmission line and Reservoir works can be taken simultaneously and immediately.
As per experience, Distribution works are likely to deviate from the original plans due to
change in user demand. Therefore, distribution work can be taken up after finishing Rising
main and Storage tanks. Accordingly procurement of distribution pipes can be phased out
suitably. Ground water recharging works should be taken after rainy season and be completed
before the next rainy season or at least constructed to a safe level so that it withstands the
impact of the floods. Sanitation work can commence simultaneously but water supply should
be available by the time sanitation works are completed and put to use.
c) Testing of Materials
All materials like sand, cement, aggregates, steel, GI pipes, PVC pipes, Pumps,
Electrical goods, paints etc shall conform to not less than BIS specifications. All the materials
shall be tested in laboratories.
d) Construction Management:
The works allotted to contractors are on turnkey basis i.e. all the materials will be
procured by the contractors.There shall be 3 tier structure for effective construction
management „
Local level by SDE / EE of DWSS
SE of DWSS
Indepenedent construction quality control at head quarter levelunder the control of CE
of DWSS
. Water supply and sanitation department will watch progress and milestones and will take
corrective actions wherever necessary. Checklists to carry out quality adherence are given
130
elsewhere in this chapter. The DWSS will appoint a central Construction quality surveillance
team, which will carryout random checks, suggest remedial and preventive measures. Water
supply and sanitation department will take appreciation action and disciplinary action on the
project staff as per the need. The Contractors are expected to carry out the work in the most
professional way and will be watched closely. Avoidable Time over runs will be viewed
seriously. The quantities mentioned in the BOQ will be strictly adhered up to the given
allowance. Any increase or decrease will be discussed with the appropriate authority and
written permission will be taken before execution.
e) Payment Schedule to contractors:
Contractors prepare their bills which will be checked and recorded in measurement
books by the concerned Sub Division Engineers with recommendation to GP for payment for
the satisfactory works. Payments should be done to finished items only. Examples: supplying
and fixing of pipelines duly tested. Reservoirs on commissioning, Groundwater recharging
structures on completion or on attaining safe situation, etc. The emphasis should be to keep the
Construction management at safe and healthy level.
f) Commissioning & Trial Run.
On completion of all civil works, the project will be commissioned PSEB would have
sanctioned electric supply, as registration would have been done immediately after the water
yield and quality test. If electric supply is not available then the contractor will provide captive
power and trial run will commence. The trial run will be for 3 months preferably in lean
months. GPWSC will be involved actively during this period.
131
2 Is water measured for concreting
3. Is vibrator used
4. Is slump test done
5. Is bulking of sand determined
MASONRY
1. Are bricks soaked in water before use
2. Are joints broken
3. Whether Masonry started from corner
4 Whether masonry constructed for uniform Height
5. Is mortar applied to each brick before placing in position
6. Is dressing of stone done before placing
7. Is watering of stone done before placing
8 Are bond stones dressed
9 Is base of face stones more than height
10. Is the masonry to plumb
11. Are the joints raked
RCC WORKS
1 Are cover blocks cast in CM-12
2 Are centering supports spaced less than 0.6 mts and
Adequate braces provided
3. Are the posts resting on firm ground with wooden wedges
4 Are steel plates used for centering bottoms and sides
5 Are the gaps in centering closed
6 Is centering level checked
7 Is plumb checked for columns
8 Is centering checked / approved before placing reinforcement
9 Is reinforcement as per drawings
10 Are chairs used to prevent disturbance of reinforcement
11 Are lap lengths OK and at suitable position
12 Is reinforcement checked/ approved and measurement
Recorded before placing concreting
13 Is water proofing done when roof slabs are green
14 Is curing being done at the time of visit.
15 Is remolding done after the required period
132
16 Are patches of surface touched immediately after demolding.
PLASTERING
1. Is the sand for plastering free from silt
2. Is the surface cleaned and watered before plastering
3. Are the plumb, line and thickness checked and correct.
PIPES, SPECIALS AND APPURTENANCE
1 Are the locations as per plans
2. Are the flanged dimensions as per standard thickness, pitch,
Circle/dia.
3. Are the faces of flanges machined
4 Is rubber insertion of required quality and thickness.
5 Are the bolts and nuts are good quality and sizes.
6 Are the pipes and specials aligned to gradient and plumb
7 Are the bolts and nuts tightened properly.
8 Are the specials and valves supported properly.
9 Are thrust blocks provided for bends.
PIPE LAYING
1 Is alignment of lines as per plans
2. Is trench dimensions and levels as per plans
3. Is the soil at the bottom of pipes good for laying of pipes
4 Are the pipes and specials lowered and aligned true to
gradient and line.
5 Is the required cushion provided
6. Are pipe ends cleaned before joining
7 Follow manufacturers instruction for joining (PVC pipes)
8 Are the pipes cleaned inside before laying
9 Are the ends of pipelines closed before the days work.
10. Are air valves and reflex valves, scour valves provided at
stipulated locations.
11 Are the pipe lines tested before commissioning
12. Is refilling done gently and consolidated
The discharge and head of pumps shall be as per the design requirement. Electrical fittings
will satisfy the requirements of the PSEB.
Typical formats for testing of various materials used in the water supply scheme are
presented in the following pages to have uniform data and also as a guideline for minimum
tests to be conducted on the materials.
133
PUNJAB RURAL WATER SUPPLY AND SANITATION PROJECT
Signature
134
PUNJAB RURAL WATER SUPPLY AND SANITATION PROJECT
135
PUNJAB RURAL WATER SUPPLY AND SANITATION PROJECT
137
2. TYPICAL FORMAT OF TEST REPORT
ON FINE AGGREGATE
Source of sample : Sample supplied by the client
Client‟s Reference : Letter No………….. dated………..
Date of Test : ………………
Project : ………………..
Contractor : ………………..
Sample No. : ……………….
Technical Reference : IS:2386 (Part I to VIII)-1963 (Reaffirmed-1990)
IS Sieve Designation Cumulative Percent Specification as per IS:383-1970 (Reaffirmed 1990)
for fine aggregate (%age Passing)
Retained Passing Zone-1 Zone-II Zone-III
04.75 mm 90-100 90-100 90-100
02.36 mm 60-95 75-100 85-100
01.18 mm 30-70 55-90 75-90
600 microns 15-34 35-59 60-79
300 microns 5-20 8-30 12-40
150 microns 0-10 0-10 0-10
Remarks
138
3. TYPICAL FORMAT OF TEST REPORT ON
COARSE AGGREGATES
Source of sample : Sample supplied by the client
Client‟s Reference : Letter No…………..dated………….
Project : ……………..
Date of test : ……………..
Technical Reference : IS:2386(Part I to VIII)-1963 (Reaffirmed-1990)
139
4. TYPICAL FORMAT OF TEST REPORT ON
BRICKS
Source of sample : Sample supplied by the client
Number of samples tested : ………………..
Client‟s Reference : Letter No…………..dated………….
Project : ……………..
Identification : ……………..
Period of test : ……………..
Technical Reference : IS:3495-1992 & IS 1077-1992
1. COMPRESSIVE STRENGTH:
Sr. Brand Measured Compressive Average Requirements as per
No. Size (mm) Strength compressive IS:1077-1992 for Class
(N/sq. mm) strength Designation 3.5
(N/sq.mm)
When 5 samples tested for
compressive strength,
average compressive
strength shall not be less
that 3.5 N/sq.mm
140
5. TYPICAL FORMAT OF TEST REPORT ON
SOLID/ HOLLOW CONCRETE BLOCK
Source of sample : Sample supplied by the client
Client „s Reference Letter no : Dated:
Number of samples tested : ………………..
Client‟s Reference : Letter No…………..dated………….
Project : ……………..
Identification : ……………..
Period of test : ……………..
Technical Reference : IS:2185(Part-I) –1979 (Reaffirmed-1992)
1. COMPRESSIVE STRENGTH:
Sr. Measured Compressive Average Remarks
No. Dimension Strength compressive
(mm) (N/ mm2) strength (N/mm2)
1
2
3
4
5
Requirements: When 8 samples tested for compressive strength, average strength shall not be
less than 3.5 N/sq.mm for blocks used as load bearing members.
II. WATER ABSORPTION:
Sr. Measured Dimension Water Absorption Requirements as per IS:2185-
No. (mm) (%) 1979 (Reaffirmed-1992)
The average water
absorption shall not
be more than 10%.
Requirements: The average density of solid concrete blocks shall not be less than 1800
Kg/cu.m and shall not be less than 1500 Kg/cu.m for hollow concrete blocks.
141
6. TYPICAL FORMAT OF
COMPRESSIVE STRENGTH TEST REPORT
ON CONCRETE CUBES
The 28 days compressive strength of cubes tested shall not be less than the grade of concrete
specified plus 3.5 N/mm2 (fck + 3.5)
142
7. TYPICAL FORMAT OF
REINFORCEMENT STEEL TEST REPORT
Source of sample : Sample supplied by the client
Number of samples tested : ………………..
Client‟s Reference : Letter No…………..dated………….
Date of test : ......................
Project : ……………..
Identification : ……………..
Grade : Fe 250 / Fe 415
Technical Reference : IS:1608-1995,IS:1786-1985(Reaffirmed in 1996)
a) Proof Stress
Dia of Wt. Proof stress Ultimate Tensile Elongation Bend Rebend
bar Kg/m N/mm2 Stress (N/mm2) (%)
143
8. TYPICAL FORMAT OF TEST REPORT ON
ANALYSIS OF WATER SAMPLE FOR CONSTRUCTION
Source of sample : Sample supplied by the client
Client‟s Reference : Letter No…………..dated………….
Project : ……………..
Identification : ……………..
Period of test : ……………..
Technical Reference : IS: 456-2000
IS:3025-1983 (Part 11,15,16,17,18,22,23,24,&32)
Sr. Particulars Constituents Stipulation of IS:456-
No. Determined 2000
1. Quantity of 0.02N NaoH required to Shall not be more than
neutralize 100ml of water sample 5 ml.
using phenolphthalein as an indicator
2. Quantity of 0.02 N H2 SO4 required to Shall not be more than
neutralize 100 ml of water sample 25ml.
using mixed indicator
3. Inorganic Solids 3000 mg/ I max
4. Sulphates as SO4 400mg/lt max
5. Chlorides as CI 500mg/lt max for RCC
2000mg/lt max for
PCC
6. Suspended matter 2000mg/lt max
7. Organic matter 200mg/lt max
8. pH valve Shall not be less than 6
144
Chapter 14
Specific Water Treatment Processess:
Sizeable Fluoride removals are possible only when magnesium is present in large quantities
which may not always be the case and magnesium have to be supplemented in the form of
salts. The process is suitable only when the water is being softened.
Magnesia and calcinated magnetite have also been used for removal of fluoride from
water. The study established the following empirical relationships for amounts of MgO which
are required to obtain 1 or 2 mg F/1 in treated water.
(a) MgO required to obtain 1 mg F/1 in treated water (F0> 2mg F/1)
(b) MgO required to obtain 2mg F/1 in treated water (F0>3 mg F/1)
F0 represents the fluoride concentration in the raw water. The pH of the treated water was
always beyond 10 and its correction by acidification was essential, adding to the
complexity of operations and control.
14.1.4 Aluminium Salts
Aluminium salts like filter alum and activated aluminium and alum treated cation exchangers
have shown beneficial effects. Filter alum during coagulation brings about some removal of
fluorides from water. The removal efficiency is improved when used along with a conagulant
aid-like activated silica and clay. 300 to 500 mg/1 of alum is required to bring down fluoride
from 4.0 mg/1 to 1.0mg/1 while with coagulant aid, the fluorides were reported to be reduced
from 6.0 mg/1 to 1.0 mg/1 with alum dose of only 100 mg/1.
Alum treated polystyrene cation exchangers and sulphonated coals have also been used
successfully. A cation exchangers prepared form extract of Avaram bark and formaldehyde
when soaked in alum solution has been found to have good fluoride removal capacity
(800mg/kg.)
Calcinated or activated alumina in granular form can be used fluoride removal and the
spent material regenerated with alkali, acid or by both alternately (removal efficiently 1.2 kg
of fluoride/m3). A dilute solution of aluminium sulphate used as the regenerated for the spent
material makes the alumina four times more efficient.
14.1.5 Simple Method of Defluoridation
Deluoridation is achieved either by fixed bed media which chould be regenerated or by the
process of precipitation and formation of complexes. A simple method of defluoridations is
employed in the Nalgonda Technique. It involves the use of aluminium salts for the removal
of fluoride. The Nalgonda Technique employs either the sequence of precipitation, settling
and filtration or precipitation, floatation and filtration and can be used for domestic as well as
community water supply schemes.
(i) Domestic Treatment-Precipitation, Settling and Filtration
Treatment can be carried out in a container (bucket) of 40 1 capacity with a tap 3-5 cm
above the bottom of the container for the withdrawal of treated water after precipitation and
146
settling The raw water taken in the container, is mixed with adequate amount of like or
sodium carbonate, bleaching powder and aluminium sulphate solution, depending upon its
alkalinity and fluoride content. Lime or sodium carbonate solution is added first and mixed
well with water.
Alum solution is then added and the water stirred slowly for 10 minutes and allowed to settle
for nearly one hour. The supernatant which contains permissible amount of fluoride is
withdrawn through the tap for consumption. The settled sludge is discarded. The amount of
alum in ml to be added in 40 litres of water at various alkalinity and fluoride level is given in
Table 14.1 .
Table 14.1 : ALUM DOSE FOR DIFFERENT FLUORIDES AND ALKALINITY LEVELS
Test Water Fluoride Test water alkalinity, mg CaCO3/1
mg F/1 125 200 300 400 500 600 800 1000
2 60 90 110 120 140 160 190 210
3 90 120 140 160 205 210 235 310
4 160 165 190 225 240 275 375
5 205 240 275 290 355 405
6 245 285 315 375 425 485
8 395 450 520 570
10 605 675
147
BARC has been interacting in recent years with the Government of Rajasthan, Government of
Lakshadeep and Tamilnadu Water Board and will further expand this contact with
Government of Gujarat, Maharastra, Andhra Pradesh and Karnataka. It has been providing
consultancy services to several private parties and government undertakings. The mobile/
transportable desalination units based on RO & VC technology are in the advanced stage of
development. Standardized modules both for RO (5-50 m3/d) and small thermal desalination
units (5-50 m3/d) using waste heat (diesel or solar) specific to individual needs have been
developed. development of water scarcity areas and large coastal arid zones of the country.
RO plants are manufactured in private sector and are being installed in several places. The RO
process can be used for removal of Fluoride and Iron.”
Treatment Process:
This plant is aimed to treat the ground water to meet the WHO and IS: 10500 Standards. It is a
7-stage purification process consisting of sedimentation, Adsorbent media filtration, activated
carbon filtration, 5 and 1 micron cartridge filtration, reverse osmosis membrane filtration and
UV disinfection.
The raw water from bore well is pumped in to raw water sedimentation tank and is then sent
through an AMF, where Iron and TSS is removed. The water then flows to ACF where
organics and excess chlorine are removed. Finer particles in water are further eliminated by
flowing it through the 5 and 1 micron cartridge filters. The physically purified water now sent
to RO process for the removal of Iron, dissolved solids and organics. Finally, the water is
disinfected using UVW system to eliminate the pathogens. Periodically the AMF is
backwashed to remove the solids collected on the filter bed.:
General
Based on the same principle as gravity type rapid sand filters, water is passed through
the filter under pressure through a cylindrical tank, usually made of Fibre Glass with single
valve operation wherein the underdrain, gravel and sand are placed. They are compact and
can be prefabricated and moved to site. Economy is possible in certain cases by avoiding
148
double pumping Pretreatment is essential. The tank axis may be either vertical or horizontal as
shown below
Salient Features :
It shall have single valve operation for Back Wash , recirculation ,Rinse ,Filter Waste
close to eliminate leakage from individual valves .
Give visual indication as to the present operation of the filter.
It shall have Multi port valve with quick connect threaded barrel unions .
It shall have Hydraulically balanced laterals to maximize water flow and automatic air
bleed .
Tank of the pressure sand filter shall be made of Fibre Glass .
Disadvantages
a) In case of direct supply from pressure filters, it is not possible to provide adequate
contact time for chlorine.
b) Because the water is under pressure at the delivery end, on occasions when the
pressure on the discharge main is released suddenly, the entire sand bed might be
disturbed violently with disastrous results to the filter effluent.
149
CHAPTER - 15
COMPLETION PLAN AND REPORTS
When a project is commissioned and handed over, the history of the project has to be
maintained. The advantages are, firstly it will be helpful while carrying out O & M functions,
secondly it will act as a guide for future projects and thirdly it will examine the mistakes
committed, why happened and how to avoid in future projects. This chapter explains how
completion reports are to be prepared fulfilling the above requirements.
15.1 As Built Drawings/ Completion Drawings:
On execution of scheme components as per approved working/ construction drawings,
it is necessary to prepare completion plans. The as built drawings may have to be prepared
based on the construction drawings with modifications made while execution or variations to
suite site conditions. The completion drawing in other words are as built drawings and it shall
indicate all changes made during execution. These drawings and other project data shall be
prepared in electronic format in relevant software like Auto Cad MS Excel etc to ensure easy
storage and retrieval of the data. This data shall be stored in central computer and can be
accessible through internet to the authorized user .
Note down the modifications, variations, changes made while carrying out works on
the construction drawings with all site particulars for preparing as built drawing.
Site plan or location plan with distance, angles with respect to other permanent
objects for easy identification.
All plan dimensions as built at site, cross sections strata details in case of bore
well/ open well.
Alignment and location of pipe sizes indicating size, material of construction,
classification, depth at which it is laid, location of valves, types, sizes, material of
construction.
If no changes are made, the construction drawing shall be certified that work is
executed strictly as per the drawing and signed by Engineer-in-charge with seal
having date, name and designation.
If there is any change during execution then as built drawing is to be prepared to
reflect the change made and certified that work is executed as per this drawing.
15.2 Completion Report:
(a) The completion Report shall contain all the text information of the project that may
be required in future for reference. This will be useful for carrying out O&M
activities and while upgrading the scheme. The completion report shall have the
following information .
Name of work
- Estimated cost
- Name of the Implementing Office
- Name of Agency/ Contractor
- Work order No. and date
- Time stipulated for completion
- Date of commencement of work
- Date of completion of work
- Date of Handling over to GPWSC
- Cost as per final Bill of contract
150
- Cost of completion (contract and other components if any)
b) Cost over runs:
List of all sub works of scheme to be furnished with costs in the following format to
indicate abstract of scheme.
Sr. Name of Sub work Cost as per Variation Reasons for
No. Estimate Completion (-) savings Variations
(+) Excess
1 Tube well
2. Pump Chamber
3. Pumpset
4. Piping inside PC
5. Disinfections
Arrangement
6. OHSR
7. Rising Main
8. Distribution
9. Development of W/W
10. Topographical Survey
11. Electric Connection
12. Environment
Provision
13. General Adv. &
others
d) Comparative statement showing quantity, rates as per estimates and actual and
reasons thereof or variations.
Sr. Description As per Estimate/ As per Execution Qty. of item Item which
No work order which varied varied the
. by 25% amount by
25%
Qty Rate Amt Qty Rate Extra (-) Saving (-) Saving
Executed (tendered Items (+) excess (+) excess
rate)
1 2 3 4 5 6 7 8 9 10
1) Joint verification by Department and GPWSC of assets created within village as per
estimate
2) Joint assessment of the performance of the system. Service delivery – Quantity,
Quality, Reliability at household level.
3) Proforma of handing over the in village facilities
i. List of assets
ii. Completion plans (soft copies)
iii. Check list for O & M and format for registers.
4) Complaint Redressal ( Help line) to be provided to GPWSC
i. Contact particulars of the Construction/O&M contractors
ii. Contact particulars of the Department Engineers
152
5) Financial details - O&M budget, consider payment for bulk water and fix tariff
6) Social Audit.
Common facilities:
1) Form SLCs with representation from both existing and new villages,
2) Joint verification by Department and SLC of common facilities as per estimate
3) Joint assessment of the performance of the system delivery at each Village ESR of
designed quantity, Quality and Reliability.
4) Provide to SLC
a. List of common facilities
b. Completion plans (soft copies)
c. Check list for O & M and format for registers.
5) Complaint Redressal ( Help line) to be provided to SLC
6) Contact particulars of the Construction/O&M contractors
7) Contact particulars of the Department Engineers.
8) Financial details - O&M budget, consider payment to be made to Department for bulk
water and fix tariff for collecting from GPWSC
9) Social Audit.
153
CHAPTER-16
RAIN WATER HARVESTING
In the urban and rural areas part of the rain water collected from the surface can be harvested.
The available rain water is collected in the water bodies such as dams, lakes and ponds but
major part flows as surface run-off and in many places it stagnates on the roads and shallow
depressions. The rain water can be diverted to the existing water bodies or else a pond may be
constructed at suitable places to collect such water. This method serves both to avoid water
stagnation on the roads as well as from water works area (WTP) and to use
the rain water for recharge of ground water. The recharge from such water bodies depends on
the availability of permeable formations at the bottom of the pond. If the pond has permeable
formations then the water can percolate at a rate that depends upon the porosity of the
formations. If the bottom of the pond is made up of impermeable formations, then a provision
has to be made to reach the underlying permeable formations by means of constructing a shaft
or bore well. If the permeable formation is at a shallow depth, then a shaft or open well may
be constructed at the bottom of the pond to lead the rain water into the permeable formation
for effective recharge. If the depth of the permeable formation is more, then the only option is
to construct a bore well that penetrate the deeper permeable formations. For Rain Water
Harvesting Guidelines of Central Ground Water Board Govt. of India for Roof Water
harvesting may be referred.
156
hydrogeology of the site. Strata charts from nearest borehole existing may also be studied to
arrive at suitable conclusion.
Groundwater recharge system is comprised of:-
A Recharge Pit/Filter Pit to allow water for recharge, free from debris, floating
materials and suspended particles, which otherwise may cause serious hindrances in
recharge process by causing reduction in permeability of the aquifer. Malfunctioning
recharge systems may lead to stagnation of water and consequent hazards.
A recharge well for discharging water into an aquifer (Refer to Fig No. 14H & 14I) (of
drawings).
There are lots of abandoned tubewells available at existing water works of DWSS. Rain water
harvesting through abandoned tubewells can be done by using these tubewells. Where such
tubewells are not available, new tubewells can be installed with either M.S. Pipes & Stainless
Steel/Galvanized Cage type V- wire Screen.
Rainwater collected from rooftop of the building is diverted through drainpipes to
settlement or filtration tank.
In case of runoff from water works area, the slopes at the water works are made
towards the tubewell.
Rain Water is made to settle in the settling tank.
Optimum capacity of settlement tank/filtration tank can be designed on the basis of
area of catchment, intensity of rainfall and recharge rate.
While recharging, entry of floating matter and silt should be restricted because it may
clog the recharge structure. "First one or two shower should be flushed out through
rain separator to avoid contamination. This is very important, and all care should be
taken to ensure that this has been done." Recharge water should be silt free and for
removing the silt contents, the runoff water should pass either through a desilting
chamber or filter chamber before entering into tubewell.
After settlement filtered water is diverted to bore wells to recharge deep aquifers. A
schematic diagram is given as Fig No. 14I (of drawings).
16.1.3 Recharge Pit
D=√9÷ 2 x 4 = 2.4
π
157
Total depth of the Pit should be around 6 m to accommodate the filter media, the stored water
and a free board of 1 m.
In case of canal based scheme,
The water depth considered is 2.5 m and
Number of Pit 5 nos
In case of canal based schemes with total runoff of 120 m3/hr, 5 nos of recharge pits
are considered with water depth 2.5 m. The dimensions are worked out as below:-
Depth of Pit works out to 8 m to accommodate stored water, the filter media and a free–
board.
In case of Rainwater recharge through New Tubewells, the Recharge Pit is required to
hold the storage water only, while the filtration is effected by installation of a screen
on the recharge pipe. A water depth of 2.0 m is considered adequate for Tubewell
based scheme whereas for a canal based scheme, the water depth should be 2.5 m.
Diameters should be 2.5 m and 3.5 m respectively.
a) Artificial Recharge should be taken up in only those areas where water level is more
than 10 m below ground surface.
b) The aquifer to be recharged should be moderately thick and extensive.
c) In case of recharging of confined aquifer, the aquifers to be recharged should be
identified on the basis of strata chart of nearest borehole drilled
d) The slotted pipes should not be wrapped with nylon net which is in practice in case of
pumping wells. It reduces the effective open area, thus the intake capacity of the
recharge well decreases considerably.
e) The Stainless Steel/Galvanized „V‟ wire screen is more effective as compared to
conventional slotted pipes because 40% open area is available
f) The boreholes for construction of deep recharge wells should be drilled with reverse
circulation rotary method. However in case of shallow recharge well drilling can be
carried out with mechanized hand boring.
g) The slot openings of the slotted pipes or „V‟ wire screen used for construction of
recharging wells should be 1.5mm or 2mm as percentage of open area is more as
compared to pipes having finer slot openings.
h) The gravel used for filling the annular space around the well should be 3mm – 6mm.
i) The finer gravel reduces the intake capacity of the well and there are more chances of
getting it choked with silt.
158
j) The recharge well should be pumped now and then but preferably during the
nonrecharge times to maintain the efficiency of the well.
k) In case recharge well is not pumped the clay particles choke the screen of the recharge
well and surrounding formation material
l) First one or two showers should be flushed out through rain separator to avoid
contamination. This is very important, and all care should be taken to ensure that this
has been done.
Various arrangements of Groundwater Recharge System are presented in Fig No. 14H, 14I,
14J and 14K (of drawings).
159
Annexure A (Refer Clause 2.5.1 A )
160
Annexure B (Refer Clause 2.1)
6 Pumping 8 hours 8 hours 6 hours 6 hours in General but 8hours in General but
Hours for for availability of electricity availability of electricity
design design should also be kept in should also be kept in
populatio populatio mind at the time of fixing mind at the time of fixing
n n the pumping hours the pumping hours
161
<15000 <15000
no no
16 hours 16 hours
for for
design design
populatio populatio
n> n>
15000 15000
Pumping Pumping
time =16 time =16
hours hours
7 Pump 14X16 ft 14x16 ft 3.7mtx4.3 3.7x4.3 mt Pump Chamber cum Staff
Chamber mt Quarter
size
8 Over 30% of 30% of 50% of Capacity of OHSR shall Capacity of OHSR shall
Head daily daily Daily be calculated by Mass be calculated by Mass
service demand demand demand curve method keeping in curve method keeping in
Reservoir for for view the realistic view the realistic
capacity Pumping Pumping availability of Electricity availability of Electricity
Hours=8 Hours=8 and water supply hours . and water supply hours .
20% of 20% of Normally in Rural areas of OHSR capacity should be
daily daily Punjab Electricity is worked out for worst case
demand demand available in shifts on scenario. It should be 30%
for for rotation basis . PSEB of daily demand.
Pumping Pumping supplies electricity in
Hours= Hours= Morning shift, Evening
16 16 shift and Night Shift .
Pumping hours will vary
as per availability of
electricity . Hence before
fixing the capacity of
OHSR mass curve should
be plotted for all the three
shifts pumping of water
and supply hours . OHSR
capacity should be worked
out for worst case
scenario.
9 Pumping VT / VT / Submersibl Submersible Pump set Star rating Submersible
Set submersi submersi e Pump set Pump set
ble ble
Pump set Pump set
10 Peak 2 times 3 times 3 times of
demand of of average Usually water supply is Usually water supply is
Factor average average daily made twice/thrice a day made twice/thrice a day to
daily daily demand to the village community the village community at
demand demand at the rate of 3 hrs each the rate of 3 hrs each time
time which is equal to 6 which is equal to 6 hrs and
hrs and Alternatively due Alternatively on
to non- availability of availability of power in the
power in the day time, the day time, the distribution
distribution hours may be hours may be increased.. It
restricted to 4 hrs a day, . may be further kept in
It may be further kept in mind that demand of water
mind that demand of water is more in the morning
is more in the morning shift which may be 1.5 –2
shift which may be 1.5 –2 times of the average daily
times of the average daily demand.Hence irrespective
demand . Hence peak of the population of the
factor for designing the village, supplying hours,
distribution system shall the peak factor for
be worked out as below: designing of scheme shall
Calculation of peak flow be taken as 3.0
rate for designing the peak
flow rate
Based on above following
peak factors are
reccomneded
162
Sn Water Peak
o Supply Factort
Hours s
1 6 Hours 8
2 4 Hours 9
11 Minimum 5 mt 8mt 12 mt 12 mt 12 mt
Terminal
Head
12 Unaccoun 3 mt 3 mt 3mt 3mt 3mt
ted losses
in tees
bends and
sluice
valves
13 Stand Post 1 for 250 1 for 250 Nil 1 for 150 persons of 15 -
persons persons years prospective
of 15 of 30 population
years years
prospecti prospecti
ve ve
populatio populatio
n n
14 Provision Nil Nil N/a For high level and low For high level and low
of zoning level areas if difference in level areas if difference in
in elevation is more than 4 elevation is more than 4
distributio meters separate feeders meters separate feeders
n network shall be provided . shall be provided .
Pressure reducing valves Pressure reducing valves
shall also be provided to shall also be provided to
stop excessive water stop excessive water
supply to low lying areas supply to low lying areas
where separate feeders has where separate feeders has
not been provided . not been provided .
164
tank High level tank shall kept High level tank shall kept
in relation to filtration in relation to filtration
hours hours
29 Slow sand Rate of filtration = 2.5 kl Continuous sand filter.
filter Bed per sq meter + 25% filter
area as stand bye . Filter
shall consist of 750mm-
900 m Sand layer
supported on 225mm-300
mm gravel . The sand
shall have effective size of
0.3 mm and Coefficient of
Uniformity Cu= 2.0
30 Clear 50% of daily requirement 50% of daily requirement
Water
Reservoir
165
Annexure C -(Refer Clause 12.10 )
WATER TARIFF STRUCTURE
PUNJAB GOVERNMENT GAZATTE
(EXTRAORDINARY) Notification dt. 04.10.2002
Department of Public Health (B&R 2 branch)
No. 11/220/2002-6 B&R II/5773- Public Health Department is providing safe drinking
water in the rural area of the State. Water Supply is often interrupted by the people which
creates shortage of drinking water causing inconvenience to the general public and problems
to the Department for maintenance. To overcome these difficulties and to ensure uninterrupted
water supply in the rural areas, a system has been evolved under which fine will be imposed
on the offenders according to the nature of offence committed by them. Accordingly, the
Governor of Punjab is pleased to order the levy of fine of different offences as under:-
PUNJAB GOVT. GAZ (EXTRA) OCT, 4, 2002 (ASVN 12, 1924 SAKA)
166
The Chief Engineer (RWS-South/North)
Public Health Department,
Patiala.
Subject: Revision of user charges for repair and maintenance of Water Supply Schemes.
2. The Governor of Punjab is pleased to revise the Water Tariff structure for Private Water
Connection for households, drawing water from Public Stand Post and for commercial
establishment over a period of five years as under:-
a) Tariff for Rural Water Supply Schemes and Households drawing water from Public
Stand Post.
Sr. Year Monthly tariffs for private water Monthly tariff for
NO. connections households drawing
For normal For NABARD water from stand
schemes designed schemes designed @ posts
@ 40 lpcd 70 lpdc
1 2 3 4 5
1 2002-03 50 60 10
2 2003-04 50 60 10
3 2004-05 55 70 10
4 2005-06 55 70 15
5 2006-07 60 75 15
b) Commercial Establishment
i) The flat rate of Rs. 200/- per month per water connection from a commercial
establishment/shop situated either inside the village or on the link roads.
ii) The flat rate of Rs. 500/- per month per water connection from a commercial
establishment/shop situated on the National / State Highway.
3. This order will come into force from Ist January of every year.
167
Annexure D :(Refer clause 7.5)
1.1 This code covers the selection, installation and maintenance of inferential and semi-
positive water meteres conforming to IS: 779-1968*.
2. Selection
2.1 Water meters shall be selected according to flow to be measured and not necessarily to suit
a certain size of main. The following points shall govern the selection of meters:
a). The maximum flow shall not exceed the nominal capacity of the meter specified in IS
779-1968*.
b). The continuous flow shall be not greater than the continuous running capacity rating
specified in IS: 779-1968*.
c). The minimum flow to be measured shall be within minimum starting flows specified in
IS: 779-1968*.
Inferential water meter has the same accuracy as the semi-positive type at higher flows: it
passes unfiltered water better than a semi-positive meter and is lower in cost.
Special care is necessary in selecting the most suitable meter where large rates of flow may
exist for short periods. The normal working flow shall be well within the continuous running
capacity specified in IS: 779-1968*. as high rates of flow over short period may cause
excessive wear if the meter chosen is too small for the duty.
Owing to the fine clearances in the working parts of meters, they are not suitable for
measuring water containing sand or similar foreign matter, and in such cases a filter or dirt
box of adequate effective area shall be fitted on the upstream side of the meter. It should be
noted that the normal strainer fitted inside a meter is not a filter and does not prevent the entry
of small particles, such as sand.
3. Installation
3.1 A meter shall not be run with free discharge to atmosphere, if the static pressure on the
main exceeds 10 m head of water, otherwise the meter is liable to be overloaded and damaged.
For hose connections and similar applications, there shall always be some resistance on the
downstream side of the meter.
A Meter shall be located where it is not liable to get severe shock of water hammer, which
might break the piston or damage the rotor, and the position shall be such that it is always full
of water; a recommended method of making connection to achieve the purpose is showl1 in
Fig. I. If the meter body or adjacent pipes become partially drained of water, the accumulated
air, when passed through the meter, is registered as water, and may cause inaccuracies and
perhaps damage. The inaccuracies may be more pronounced in the case of inferential meters.
In such situations suitable devices like air-release valve may be fitted on the upstream side of
168
the meter. In the case of intermittent water supply system, where there are frequent changes of
air locks, the piston of the semi-positive meter often breaks. In such a case, it is advisable to
ensure that the top of the meter is below the level of the communication pipe.
Semi-positive meters may be fixed in any position, with the dials facing upwards or sideways,
and they may be installed in horizontal or vertical pipe runs without affecting wearing
properties of accuracy at normal service flows. Where backward flows are anticipated, reflux
valves are recommended to be provided. A stop valve should be provided on the upstream side
as shown in Fig. 1 to isolate the meter whenever necessary.
Inferential meters shall be installed in position for which they are designed; in the case of
meters conforming to IS: 779-1968*, they shall be placed horizontally with dial facing
upwards. However, where meters are to be installed in vertical pipelines, details shall be as
agreed to between the manufacturer and the purchaser.
Turbulent flow of water affects the accuracy of the meter. There shall, therefore, be straight
lengths of pipes upstream and downstream of meter for an equivalent length of ten times the
nominal diameter of the pipe.
Meters liable to damage by frost shall be suitably protected. It is possible to incorporate frost
protection devices in certain types of meters, if ordered. Several devices are adopted, the most
common among them being a collapsible metal ring which, under frost pressure, allows the
top plate carrying the mechanism to lift and thus safeguard the body, or a metal disc in the
body which gives way under pressure. These devices have the following disadvantages.
b) Water runs to waste till the meter is attended to, which means loss of revenue; and
3.6.1 A more satisfactory arrangement consists of. a method whereby the proportionate
increase in bulk of ice, which is approximately 14 percent, is accommodated by the provision
of pads of special quality
expanded natural rubber.
No arrangement, however, is regarded completely satisfactory, and for this reason, the general
practice is to install meters well out of the way of frost. Meters should be fixed below ground
level if they are located outside the building or, if in exposed portion inside the building, the
bodies of the meters should be protected with some form of lagging; in the case of meters
installed below ground, depth at which the meter should be fixed to afford frost protection will
depend on the nature of the soil.
3.7 Before installing a meter, the section of line to be metered shall be thoroughly flushed to
remove all foreign matter and, when starting up, control valves shall be opened slowly until
the line is full, as a sudden discharge may damage the meter.
3.8 Water meters may be installed underground, either in the carriage way outside the
premises or at a convenient place within the premises. In order to enable the meters to be
accessible for periodical reading, inspection, testing and repairs, they shall be housed in water
169
meter boxes conforming to IS: 2104-1962*. Top of the meter box shall be placed at a slightly
higher level than the surrounding ground level so as to prevent ground water entering in and
flooding the chamber during rains.
3.9 The meters and connecting pipes shall be strongly supported for protection of the meters
and to avoid noisy vibration.
4. MAINTENANCE
Irrespective of these considerations, the meters should be tested at least once in two
years.
4.1.2 In case of inferential water meters, water is passed even if the meter stops registering,
whereas, in the case of semi-positive meters, the water supply would be shut off when the
meter stops registering. From the waters supply would be shut off when the meter and having
regard to the seasonal fluctuations in the demand for water supply of a consumer, it is possible
to determine whether the meter requires to be removed for test, being suspected of running
slow.
4.2 When a meter is removed from the line for whatever reason, opportunity should be
taken to see that it is clean and functioning properly before it is re-installed. It should also be
tested for accuracy and reset to zero before installation.
170
Annexure E (Refer clause 7.5)
Specification for Water Meters (Bulk Type)
Foreword
0.1 This Indian Standard (Third Revision) was adopted by the Indian Standards Institution on
27 February 1981, after the draft finalized by the Sanitary Appliances and Water Fitting
Sectional Committee had been approved by the Civil Engineering Division Council.
0.2 This standard was first published in1963 and the first and second revisions were issued in
1968 and 1973 respectively. A third revision of the standard has been taken up to review
the standard and incorporate changes found necessary in the light of comments received
from manufacturers and user during the course of implementation of the standard.
0.2.1 In this revision, minimum thickness of the liner for enclosed type water meter has been
incorporated to ensure life of the body of water meters.
0.3 This standard contains clauses 4.6.1, 4.6.2, 4.12 and 6.2, which permit the purchaser to
use his option for selection to suit his requirements. This standard also contains clause
8.2.2, which requires agreement between the purchaser and the manufacturer.
0.4 For the purpose of deciding whether a particular requirement of this standard is compiled
with, the final value, observed or calculated, expressing the result of a test or analysis,
shall be rounded of in accordance with IS: 2-1960*. The number of significant places
retained in the rounded off value should be the same as that of the specified value in this
standard.
1. Scope
1.1 This standard covers bulk type water meters of the following types:
2. Terminology
2.0 For the purpose of this standard, the following definitions shall happy.
2.1 Meter Casing - The outer casing in which the entire meter mechanism is
housed.
171
2.2 Body – The part of the meter, which the runner and the transmission gear train
of the water meter. Some parts of the body may be integral with the casing.
2.3 Registration Box – The part of the meter casing which houses the registration
device.
2.4 Cap – The part of the meter casing body to which is fitted the dial cover and
the lid.
2.5 Lid – The tope cover, which is hinged to the cap with a view to protecting the
transparent dial cover.
2.6 Registration Device – The unit, which comprises the recording gear train and
the indicating device consisting of a cyclometer type counter or pointer on a
dial or a combination of both. It registers in suitable volumetric units the
quantity of water, which has passed through the meter.
2.7 Vane Wheel Type Meter – Meter whose runner or impeller is mounted on a
vertical spindle, which has several vanes symmetrically spaced round its axis.
The water impinges on the runner over a part or the whole of its circumference.
2.8 Helical Type Meter – Axial flowmeter whose runner is provided with a
number of vanes forming a multi-threaded helix.
2.9 Water Meter, Dry Deal Type - Meter in which the counter mechanism is
isolated from water flowing through the meter.
2.10 Water Meter, Wet Dial Type – Meter in which the complete counter unit is in
contact with water flowing through the meter.
Nominal Size
MM MM
50 250
80 300
100 350
150 400
200 500
3.1.1 The nominal size of water meters shall be denoted by the bore of their inlet.
4.2.1 Casing – The casing of the meter shall be made from cast iron conforming to
grade FG 200 of IS: 210-1978* or bronze conforming to grade 2 of IS: 318-
1962* or brass conforming to Grade 3 of IS: 292-1961* grade cuzn 40 of IS:
1264-1965.
4.2.2 Body – The body of the water meter shall be made of bronze conforming to
grade 2 of IS: 318-1962* or brass conforming to grade 3 of 292-1961* or
Grade CuZn 40 of IS : 1264-1958. in the case of enclosed type water meters as
the liner shall be made of minimum 1.5 mm thick brass sheet conforming to IS
: 410-1977.
4.2.2.1 The body shall be free from all manufacturing and processing defects, such as
blow holes and spongy structures and shall not be repaired by plugging,
welding or by the addition of material. The integral shape of the body shall
ensure smooth flow of water and easy dismantling.
4.3 Connections – The water meter shall be provided with flanges at both the ends, the
internal diameter of which shall be equal to the nominal size of the meter. The
flanges shall be machined flat, that is, without a raised joint face. The dimensions
and drilling of the flanges shall be in accordance with IS : 1538 (Part IV) –1976
and IS : 1538 (Part VI) –1976**. Tolerances on dimensions and drillings shall be
in accordance with IS : 1538 (Part I) –1`976 **. For meters of 50 mm size the
dimensions and drilling of flanges and tolerances shall be in accordance.
4.4 Screws, Studs, and Nuts – Screws, Studs and Nuts shall be of mild steel, brass or
some other corrosion resistant material. Where fasteners are likely to be in contact
with water, they shall be made of brass conforming to IS: 318-1962* or of stainless
steel conforming to designation 07 or 18 Ni 9 of IS
4.5 Registration Box – The registration box shall be made of the same material as
specified for body in 4.2.2.
173
4.6 Cap - The cap shall be made of the same material as specified for body in
4.2.2. The cap shall be so designed and fixed to the registration box as to avoid
entry of water and dirt. The transparent window, which covers the dial, shall be
inserted from the inside into the cap. The protective lid shall be secured by a
robust hinge or other suitable methods of robust construction.
4.6.1 Where required by the purchaser, provision shall be made to lock the lid to the
registration box. The provision shall be such that the lock may be conveniently
operated from the top. - Where the provision is designed for use in conjunction
with padlocks, the hole provided for padlock shall be of diameter not less than
4 mm.
4.6.2 Where so required, for dry type water meter, the transparent window covering the
dial shall be provided with a wiper on the inner side for wiping off condensed
water.
4.7 Strainer - Strainers shall be made of a material which is not susceptible to
electrolytic corrosion. They shall be of plastic or other corrosion. resistant
materials. They shall be rigid, easy to remove and clean and shall be fitted on
the inlet side of the water meter. The strainer shall have total area of holes not
less than twice the area of the nominal inlet bore of the pipe to which the meter
is connected. Where strainer is installed outside the meter, it shall be at such a
distance that it does not affect the accurate functioning of the meter.
4.8 Runners (Impellers)
4.8.1 The runner shall be of tensile brass conforming to IS: 320-1962*, stainless steel
conforming to designation 07 Cr 18 Ni 9 of IS: 1570 (Part V )-1972t or nickel
alloys conforming in IS: 4131-1967*.
4.8.2 Runner of the meter shall be of ebonite, vulcanite, or suitable plastic, bronze
conforming to Grade 2 of IS :318-1962§, stainless steel conforming to
designation 07 Cr 18 Ni 9 or IS: 1570 (Part V )-1972t or nickel alloy
conforming to IS: 4131-1967;. It. shall be accurately balanced. Runner shall be
durable and shall work with as low frictional resistance as possible.
4.9 Runner Chamber - In the case of vane-wheel type meters, the runner chamber
shall be of brass conforming to Grade 3 of IS : 292-1961*. Bronze conforming to Grade 2 of
IS: 318-1 962t. Stainless steel conforming to designation 07 Or 18 Ni 9 of IS: 1570 (Part V)-
1972: or nickel alloy Conforming to IS: 4131-1967§. The runner chamber shall be rigid and
174
shall not change its form as a result of internal stresses or with use.
4.10 Gears - Gears shall be 10 constructed as to tully and smoothly mesh with each
other. and shall be firmly fitted on their shaft. Gears coming in contact with
water shall be of stainless Steel conforming to designation 07 Or 18 Ni 9 of IS:
1570 (Part. V)-1972: Or nickel alloy conforming to IS: 4131-1967§. In the
helical type meters, the worm gears may be fined on a shaft and the worm
wheel shall be enclosed and protected against the incursion of solid particles.
4.11 Bearings- Impeller bearings shall be of agate, sapphire, graphite filled nylon or
graphite filled ebonite suitable ground and polished. The shape of the impeller
bearing shall be such as to prevent the penetration of particles of sand and to
preclude the deposit of anything in solution or suspension in water and to
facilitate the washing away of such deposits by water flow. The shafts of the
gears shall revolve freely in their bearings. The length of the bearing shall
ensure their effective operation.
4.12 Counting Mechanism - The pointer shall be made of sheet brass conforming to'
410-197711 or suitable plastic. The counter shall be of circular multi-pointer
pattern with all pointers preferably reading clockwise. The indicating device
may also be of the straight reading cyclometer type counter or a combination of
pointer and the counter. The rollers of the cyclometer counter shall be made of
nickel or nickel-plated brass or plastic specially suitable for the purpose and
shall be self lubricating. The external numbering shall be such that it will not
fade away under continued use.
4.12.1 The range of registration shall be as given in Table 2.
4.13 Dial- The dial shall be of vitreous enamel, copper or suitable plastic, ensuring
indestructible marking and good legibility. The unit of measurement namely,
'litre' or 'kiIolitre" shall be marked on the dial 81 'LITRES‟ or : „KILOLITRES‟
in boldface; the unit, cubic metre (m2) may also be used in place of kilolitre.
4.14 Sealing - Sealing holes shall be provided and the meter shall be sealed in such
a manner as to render it inaccessible to the 'measuring unit, including
registration box and cap without breaking the seal. The sealing wire shall be
rust proof such as tinned copper.
4.15 Regulator - Every meter shall be provided with either an external or an internal
regulator. The external regulator shall be accessible from outside to be operated
by a suitable key without dismantling the meter and protected by a sealed
175
cover. The internal regulating device shall not be accessible from outside.
4.16 Location of Serial Number - The serial number of the meter shall be clearly
indicated in any suitable place except the lid.
Performance Requirements
5.1 Temperature – The meter shall be suitable for use with water up to 450C.
5.1.1 Temperature Suitability Test – The water meter shall be immersed in
a water-bath maintained at 45± 10C for 10 h. afterwards it should be
checked for flow and accuracy tests.
5.2 Hydrostatic Test – Meters shall satisfactorily withstand a pressure of 1.6 MPa (16
KGF/CM2).
5.3.3 The headloss within meters shall be measured in accordance with the method
given in Appendix B.
5.4 Minimum Starting Flow - The minimum flow at which the meters start registering
shall be as given in Table 5.
5.5 Metering Accuracy - The accuracy at lower limit of flow shall be calculated at one-
thirtieth of the nominal capacities of water meters given in Table 3; at the lower
limit of flow, the metering accuracy shall be ± 2 percent for both types of water
meters. The same accuracy shall he complied with at least up to intermediate flows
176
specified in Table 4.
6.1 Meters liable to be damaged by frost shall be protected with suitable frost
protection devices. Several devices are adopted and the following, which have been
found to give satisfactory performance, are given as typical examples:
a) Provision of pads of special quality rubber which accommodate the increase in bulk
of water when it freezes; and
b) Provision of collapsible metal ring which under frost pressure allows the top
plate carrying the mechanism to lift and so safeguard the body, or a metal disc in
the body which gives way under pressure. It should be noted that the damaged ring
or plate requires immediate replacement to restore water supply to user or to stop
waste. .
6.2 The purchaser shall specify with his order whether he requires frost protection device.
7. MARKING
7.1 Each water meter shall be marked with the following information: a) Manufacturer's name
or trade-mark,
b) Nominal size of the meter, and
c) Direction of flow of water on b9th sides of the meter.
7.1.1 each water meter (with or without strainer) may also be" marked with the ISl
Certification Mark.
NOTE - The use of the 151 Certification Mark is governed by the provision of the
Indian Standards Institution (Certification Marks) Act and the Rules and Regulations
made thereunder. The ISI mark on products covered by an Indian standard conveys the
assurance that they have been produced to comply with the requirements of that
standard under a well-defined system of inspection, testing and quality control, which
is devised and supervised by ISI and operated by the producer. 151 marked products
are also continuously checked by 151 for conformity to that standard as a further
safeguard. Details of conditions under which a licence for the use of the 151
177
Certification Mark may be granted to manufacturers or processors, may be. obtained
from the Indian Standards Institution.
8. TESTS
8.1 Classification of Tests - Tests shall be classified into three groups, namely (a)
production routine tests, (b) type tests, and (c) acceptance tests.
8.1.1 Production Routine Tests -. These tests are carried out on each and every meter
to check the requirements, which are likely to vary during production.
8.1.2 Type Tests - These tests are carried out to prove conformity to the requirements
of the relevant specification. These are intended to check the -general quality
and design of a given type of meter (see 8.4 ). Once a meter has undergone type
tests, any major or essential alterations, which the manufacturer intends to
make, shall be reported to the testing authority and further type tests shall be
carried out in accordance with the procedure laid down in this standard.
8.1.3 Acceptance Tests - 'tests carried out on samples selected from a. lot for the
purposes of acceptance of the lot.
8.2 Samples for Tests
8.2.1 Type Tests - Two meters in the case of 50 mm size and one meter in the case of
80 mm size and above shall be sent along with 4 copies of the manufacturer's
detailed specification together with figures for the loss of head and accuracy curves
to the recognized testing authority for the purpose of type test. The samples shall be
picked up at random from stock or routine factory production.
8.2.2 Acceptance Tests - The number of samples shall be agreed to between the
manufacturer and the purchaser.
8.3 Production Routine Test - Production routine tests shall consist of:
a) Hydrostatic test ( set 5.2 ), and
b) Tests conducted requirements to determine the following performance requirements
1) Recommended capacity for intermediate flows (set 5.3.2and Non: given below),
2) Minimum starting flows (see 5.4), and'
3) Metering accuracy (see 5.5).
178
8.4 Type Tests - Besides all the production routine tests outlined in 8.3, the type tests
shall comprise those given in 8.4.1 and 8.4.2.
8.4.1 Construction - The meter shall be dismantled completely to its component
parts and checked for conformity with regard to dimensions and
tolerances with this standard; in the case of meters of 50 mm size, only
one meter need be dismantled. A study of the details of assembly shall be
made on matters, such as case of assembly, absence of riveted or turned
over parts, forced fitting and liability of, parts to break during dismantling
and assembly.
8.4.2 Flow Test - The meter (both the meters in the case of 50 mm - shall then
be subjected to the flow test to measure the following:
NOTE 1 - Before the meter is subjected to the flow test it shall be run and brought to
normal condition by passing through them water at intermediate flow value for a
period of two hours. -
NOTE 2 - Type test certificate may be made available in lieu or' flow test at
manufacturer's premises.
8.4.2.1 Results of the type tests shall be reported in the form given in Appendix C.
179
APPENDIX A
Clause 4.1)
A-I. The following information shall be supplied by the purchaser with the enquiry and
orders:
180
APPENDIX 8
(Clause 5.3.3)
B-1. DETAILS
B-1.2 The regulating valve shall be situated at a distance not less than. 40 times
the diameter of the pipe from the inlet end of the water meter. When the feed of
the water is through a pump instead of through an overhead tank; the pump shall
be situated and where required suitable damping devices, such as air vessels or
automatic pressure Switches, shall he so provided that the pulsation in the flow
water through the meter is reduced to the minimum
181
APPENDIX C (Clause 8.4.2.1)
182
Annexure F (Refer clause 8.5.2)
Difference Between Dosatron Non electricity based water powered liquid
dispencer dosing pumps and conventional pumps
Unlike other systems, proportional dosing Over or under dosing risk when not servo-
provides uniform distribution of the controlled.
products over the entire sector(s).
Non electric runs on water power and flow Non autonomous: Needs Electricity
dependent system.
Easy maintenance as moving parts do not Higher cost, especially with servo-control
have metal parts. No high installation cost. installation.
Simple piping required.
Saving in electricity. About Rs. 800/- per No saving of electricity it is must for
month and Rs.9600/- per Annum. running.
Longer life of about 10 years or more Average life 1to 2 years it means
subject to quality of water only periodically department has to buy in 10 years 9 times.
AMC is required. Units of about Rs. 315000/-.
183
ANNEXURE G (Refer Chapter 12)
OPERATION AND MAINTAINENECE
DETAILS REQUIRING ATTENTION TO PREVENT OPERATIONAL PROBLEMS IN PUMPING
Guide Lines for Maintenance Centrifugal Pumps :
FOUNDATION
The concrete foundation must have thoroughly dried and set before erection of the pump to ensure that loads due
to weights of pumpsets, twisting moments and inertia forces due to the machine as well as the weight of, and
thrust set up by the pipeline can be borne without any movement or settling of the foundation, Concrete
foundations for reciprocating pumps should be still heavier, and if necessary they should be isolated from the
adjacent ground by a layer of material such as sand, cork, felt padding, timber etc. capable of damping out
vibrations.
Rotary machines are invariably dynamically balanced so that no unbalanced inertia forces of any appreciable
magnitude can occur.
Vibrations of the foundations can be avoided provided the machines are correctly aligned under stilled
supervision. This is necessary even for smaller pump units usually mounted on a common base plate and lined up
before despatch to take care of the possible distortions occurring during transport or set up on site by
irregularities in the surface of the foundation.
B. SUCTION PIPES
The internal dia selected for the suction lines should in no case be less than that of the suction branch of the
pump. The suction pipe must be kept as short as possible and total suction from all causes should not exceed the
limiting value specified by the manufacturer. Normally, it should not exceed more than 4.5 m for general purpose
pumps.
Pipeline should be supported and fixed in such a manner that the pump is not subjected to any stress from
piping. To avoid the formation of air pockets, suction lines must be arranged with a continuous rise towards the
pump. Isolating valves of the gate type on the suction side should be fitted with the valve spindle horizontal and
their glands sealed by means of water from the discharge side of the pump.
When water containing dissolved air or other gas is pumped, it is desirable to provide an air separation vessel and
a divide such a vacuum pump for removing the air.
If at all possible, each pump should have a separate suction line in order to prevent air leaking in, from a pump
that is shut down. However, if the use of a common suction line cannot be avoided, the non return valves of the
184
discharge side of the pumps should be omitted, and instead such valves should be fitted immediately upstream of
the suction branches.
When a number of pumps are installed adjacent to one another, with their suction pipe in the same pump, care
should be taken to see that a minimum of 3 dia distance is kept generally between two suction pipes to prevent
aeration problem resulting in the loss of output because of entrance of air into the pump or even ceasing of some
pumps altogether.
In the absence of a suction strainer fitted with a foot valve, the inlet to the suction pipe should be bell mouthed,
situated at an adequate height above the bottom of the well, and also always submerged below the lowest water
level. The bell mouth diameter should be at least 1.5 times that of the suction pipe and it should be at a height of
at least half the dia of suction pipe, from the bottom of the sump. Vortex effects with vertical axial-flow and
propeller type pumps can be minimized by locating their bell-mouth inlets as close as possible to the rear wall of
the suction chamber.
In the case of suction strainers fitted with foot valves, it should be located at an adequate height above the bottom
of suction chamber and also submerged below the lowest surface level of the water. They should be arranged to
ensure uniform intake of water from all sides. The total are of the holes in the strainers should be equal to or more
than the cross sectional area of the suction pipe. The flow velocity in the suction branch of the pump should not
exceed 2 mps.
C. DELIVERY PIPE
Non-return valves must always be fitted when the discharge head exceeds 10m, so that in case of sudden
stoppage of pump the surge pressure due to the returning column of liquid is not imposed on the casing. The non-
return valve should be provided with a bypass so that all the surge pressure is not imposed on the seating of the
valves, but it is bypassed and the water goes to the sump. A relief valve should also be provided on the delivery
side.
PIPE FITTINGS
If it is found necessary to fit a bend immediately upstream of the suction branch of a pump, the radius of the bend
should be equal to or greater than 2 D+100mm.
Branch fitting of Y type are to be preferred to T pieces.
The length of tapered reducing pieces, when the divergence, should be about five times the difference between
outlet and inlet diameters.
If used as reduces, tapered fittings may be very much shorter; the most suitable form is that of a nozzle type.
185
E. COMMISSIONING
Priming is essential and is done by using a foot valve. In the case of large pumping units, priming is generally
done by using a vacuum pump which exhausts the air from the pump casing and sucks in the liquid from the
sump. In the case of pumps having a positive head on the suction line, priming is done by opening the valve on
suction pipe.
Prior to starting, the direction of rotation of the drive should be checked. All lubrication system should also be
checked. The stuffing boxes should be packed properly and care is taken to see that the lantern ring is located
exactly underneath the water seal piping. After making all the above checks, the coupling pins are fitted and the
rotating elements are rotated by hand or with the help of spanners in case of large units. This makes sure that the
pump will accelerate and attain full speed smoothly. Over packing of stuffing box may damage the sleeves.
The pump should be started with the delivery valve closed. On starting, check that the pump is generating the
head. This will be indicated by the delivery pressure gauge. Immediately after the pumps run to full speed, check
should be made on bearings, stuffing boxes and vibrations and residual air should be vented out by the air-cock
provided on the top of the casing.
Stuffing boxes and glands should be checked for over heating and gland leakage. The gland packing, when it is
new, does tend to get slightly heated but it comes to normal after running for sometime. A few drops of liquid
should trickle out in the gland bowl. If the gland leakage is excessive the gland should be tightened or additional
gland packing should be introduced.
The centrifugal pump should not be run on closed valve for long periods. After making all checks the delivery
valve should gradually be opened and the pump may be put on its rated load. The ammeter should be checked to
see that the meter is not overloaded.
Attention should be given to the temperature of the bearing after running the pump on its rated load. Periodic
check on temperature of the bearing should be made.
In case the pump fails to generate pressure, it should be stopped immediately and checked for air leakage from all
joints in suction pipes and the stuffing boxes.
It is most important that in no case should the pump be started without liquid, as this may result in seizure of the
internals of the pump.
186
A
“Centrifugal Pumps”
187
B
“Electrical Motors”
Sr. Name of section Maintenance to be carried out Frequency time Remarks
No or part to be internal at which
attended inspection &
maintenance to be
done
1. Induction Motor Opening of end covers dust One month Depending on the
stator & Rotor blowing & checking of air gap. working conditions
and maintenance
staff available
2. Slip Ring Device Cloaning of slip rings & One month
adjustment of carbon brushes,
shortcircuiting jaws, oiling of
clutch etc.
3. Bearings Proper lubrication Two months
4. Windings Checking of motor after taking Two years
out its Rotor, dust blowing,
checking of end connections of
stator & Rotor & taking
insulation test, no load test before
putting the motor on load.
C
SCHEDULE OF PREVENTIVE MAINTENANCE
“Power Transformers”
188
D
189
E
F
SCHEDULE OF LUBRICATION
190
APPENDIX-17
191
Mechanical Troubles
23. Foreign matter in impeller.
24. Misalignment.
25. Foundation not rigid.
26. Shaft bent.
27. Rotating part rubbing on stationary part.
28. Bearing worn.
29. Wearing rings worn.
30. Impeller damaged.
31. Casing gasket defective, permitting internal
leakage.
32. Shaft or shaft sleeves worn or scored at the
packing.
33. Packing improperly installed.
34. Incorrect type of packing for operating
conditions.
35. Shaft running off-centre because of worn
bearings or misalignment.
36. Rotor out of balance, resulting in vibration.
37. Gland too tight, resulting in no flow of liquid
to lubricate packing.
38. Failure to provide cooling liquid to water-
cooled stuffing boxes.
39. Excessive clearance at bottom of stuffing box
between shaft and casing, causing packing to be
forced into pump interior.
40. Dirt or grit in sealing liquid leading to scoring
of shaft or shaft interior.
41. Excessive thrust caused by a mechanical
failure inside the pump or by the failure of the
hydraulic balancing device, if any.
42. Excessive grease or oil in antifriction bearing
housing or lack of cooling, causing excessive
bearing temperature.
43. Lack of lubrication.
44. Improper installation of antifriction bearings
(damage during assembly, incorrect assembly of
stacked bearings, use of unmatched bearings as a
pair, etc.).
45. Dirt getting into bearings.
46. Rusting of bearings due to water getting into
housing.
47. Excessive cooling of water-cooled bearing,
resulting in consideration in the bearing housing
of moisture from the atmosphere.
192
APPENDIX- 18
C. Speed Too Low, hence Displacement is less than Slip through Clearances:
Check driver to see than it is upto rated speed. Change drive to increase speed, if
necessary.
Open all valves. See that flange gaskets have the centre cut out and that there if no
obstruction across end of suction pipe.
E. Strainer Clogged:
Check to see that suction pipe has not been screwed into foot valve far enough to
hold it closed.
Check with vacuum gauge. Suction lift should not be within 0.15 kg/cm2 of vapour
pressure of liquid at its pumping temperature.
J. By-Pass Open:
Examine all by pass return lines for open valves. Close them, if open. A relief valve
stuck open may by pass the entire pump capacity.
Paint and tighten all suction-pipe gaskets and threaded joints. Tighten stuffing-box
packing.
193
L. Check Valve in Discharge Backed up by Hydraulic Pressure:
Replace parts, so clearance will not cause slip equal to pump displacement.
Increase suction-pipe size and reduce its length. Lower position of pump to prevent
liquid from vaporizing and producing cavitational noises within pump.
Paint all pipe joints, replace faulty flange gaskets, repack stuffing box to stop
cracking noise due to air bubbles in pump.
Align drive with pump. Release pipe flanges to determine if they strain pump
casing enough to cause metallic contact between rotating elements an casing.
File or scrap high sports that cause rotating elements to bind and produce a noise
synchronized with each revolution.
F. Excessive Pressure:
Align driver and pump. If coupling has floating sleeve or cover, misalignment
often results in slapping sound.
Check with vacuum gauge. Suction lift should not be within 0.15kg/cm2 of vapour
pressure of liquid at its pumping temperature.
Clean the screen. If all danger of foreign material has passed and screen has
insufficient area, remove Pump.
C. Suction Pipe End Insufficient Submerged, so that liquid Eddied and Allows Air to
be Drawn into Pump:
D. Suction Pipe Too Small, Too Long, or has Many Fittings to Increase Pipe Friction
Abnormally and Cause Liquid to Vaporise:
Simplify suction line to reduce pipe friction and increase its size.
Repack box, tighten gland. Caution: Don‟t tighten enough to cause excessive
packing wear and heating.
Check driver for speed and overload. Change drive speed ratio.
195
Close all by-pass valves and see that they are sealed properly.
Regrind valve on its seat. Be sure that valve does not open until desired pressure is
reached.
Increase suction –pipe length so that liquid is not drawn down to near the end of
pipe.
A. Speed Too High, or Liquid Heavier or More Viscous than specified for Pump.
If new installation, recalculate what the head should be. Don‟t forget to include
head due to friction losses in pipe and fittings. Check this head against rated pump
head. With pressure gauge, check head developed by pump. An obstruction or
partly closed valve in discharge line may increase head above normal. If head
cannot be reduced to give safe load on motor, reduce pump speed or install larger
motor.
Check packing. If too tight, make necessary adjustments or replace packing with
correct type, properly installed.
196
D. Shaft Bent or Out of Alignment:
Check shaft, pump and motor alignment. If shaft is bent, straighten it or install
new one. Properly align pump and motor.
Pipe connection out of line distorts pump casing. Disconnect suction and discharge
piping from pump to see if they are in alignment. Flange faces should be parallel
and align axially without being forced. Support pipe separate from pump. Check fit
of rotating parts to make sure they do not bind or have not worked endwise on
shaft to rub casing.
197
ANNEXURE- H (Refer clause 6.4.3)
SPECIFICATION OF SUBMERSIBLE PUMPING SET
The submersible pumping set should conform to I.S. 8034-1989 with latest
amendment. The pump should be fitted dynamically balance enclosed type impeller. Each
impeller shall be balanced dynamically to grade of G 6.3 (6.3mm/s). The pump shaft shall be
guided by bearing provided in each stage bowl & in the suction land discharge casing. The
surface finish of shaft or of the protecting sleeves should be 0.75 micron Ra Max. The inlet
passage of the suction casing shall be stream lined to avoid eddies. The suction case shall be
fitted with a strainer of corrosion resistant material. Suitable sand guard shall be provided just
above the suction case bearing to prevent the entry of foreign material into suction case. The
pump should be provided with the non return valve above the pump discharge case with
standard flanged connection. The individual casting part or pump as a whole in assembled
condition should be able to withstand a hydrostatic pressure of 1.5 time maximum discharge
pressure. The gaskets & seals used shall conform to I.S. 5120-1968 or latest. The cable clamp
of adequate size be supplied for fixing submersible cables to the rising main pipes.
The pump shall be directly coupled to a submersible motor. The submersible motor
shall be squirrel cage induction motor conforming to I.S. 9283-1979 or latest capable of
operating on 415+ 6% volts, 3 phase 50 cycles, A.C. supply. Both pump and motor shall run
at 2900 R.P.M. The water lubricated thrust bearing should be of adequate size to withstand the
weight of all rotating parts as well as the imposed hydraulic thrust. The motor shall be
protested by means of cable glands, rubber seals etc. from ingress of bore well water, sand and
other foreign material. The motor shall be provided with breathing attachment like bellows,
diaphragm etc. to compensate the volumetric variation due to change in the temperature. The
motor shall be made of corrosion resisting material or suitable materials to resists corrosion
under normal conditions. The rotor shall be provided with shaft protecting sleeves having a
surface finish of 0.75 micron Ra Max. The starter shall be star delta. The class of insulation
shall be F. The submersible cable of L&T & finolex make for submersible motor shall
conform to I.S. 694 (Part-III)-1964 or latest. The flanged column pipe shall conform Table 2
I.S. 1239 ( Part-I )- 1979 or latest (Medium Class) Table-2.
The efficiency of submersible pump shall be guaranteed to specified point of rating
only & shall not be guaranteed to cover the performance of the pump under condition varying
there form nor for a sustained performance for any period of time. The pump discharge may
be guaranteed for the range of head between – 25% & + 10% of the specified head when the
later is 30 meters of above. Below 30 meters the limits shall be from – 25% to 25% or + 3
meters whichever is less. The H.P. of motor shall be such that is shall be 15% in the excess of
maximum H.P. required under all heads of working. Performance guarantees shall be based on
laboratory tests corrected for field performance.
198
MATERIAL OF COMPOSITION OF DIFFERENT COMPONENTS OF PUMP:
1. CALAMA or equivalent
2. KSB or equivalent
3. SU or equivalent
4. WPIL or equivalent
5. SEEREX or equivalent
199
INFORMATION TO BE FURNISHED WITH THE TENDER (As per IS: 8034-1989)
DETAIL OF PUMP
1. METHOD OF LUBRICATION:
2. MINIMUM BORE WELL DIA METER IN MM:
3. NUMBER OF STAGES
4. OUTSIDE DIAMETER OF BOWL
(The max, diameter pump fitted non return valve & max, overall diameter of the
pump set including the cable guard)
5. DISCHARGE IN LPM
6. TOTAL HEAD MTR
7. SPEDD IN RPM
8. PUMP INPUT AT DUTY POINT IN K.W.
9. OVER ALL EFFICIENCY IN %
10. MINIMUM SUBMERGENCE REQUIRED
DETAILS OF MOTOR
1. RATING IN K.W.
2. TYPE
(in accordance with I.S. 9283-1979)
ADDITIONAL INFORMATION
200
SPECIFICATION OF CONTROL PANEL FOR SUBMERSIBLE PUMPING SET
Panel board having size 900mm x 250 mm made of not less than 2 mm prestressed
cold rolled sheet & auto claved painted. The board should comprise of rigid welded
structural frames made of structural steel sections of not less than 3 mm thickness.
The board should be smoothly finished & free from flaws. The panel board should
have the following flush mounted instruments. It should have space for providing
power meter & light meter.
14. Selector switch for ammeter & Voltmeter : L&T Kaycee or equivalent
201
18. Wires:- Plaza, Kent, Finolex or equivalent
TESTS: The following tests should be performed on the panel board during the
inspection at the manufacturer place.
1. Upto 7.5 H.P. D.O.L. Starter will be installed. Above 7.5 H.P. Star Delta Starter
will be installed.
2. THE FOLLWING FAMILY CURVE ALONGWITH THE
CHARACTERISTICS CURVES SIGNED BY THE MANUFACTURER (not
below the rank of REGIONAL MANAGER OF REGIONAL INCHARGE) be
attached with the tender. Photo copy of the same will not be accepted.
+ 10% OF D.P
202
ANNEXURE-I (Refer clause 2.5.1.1 & 2.2.6)
WATER SAMPLE QUALITY TESTING AND SAMPLE COLLECTION PERFORMA
A
1. Name and address of person requesting the examination.
2. Date and time of collection and dispatch.
3. Purpose of examination.
4. Source of water and its location (well, tubewell, stream, river, etc.).
5. Exact place and depth below surface, from which sample was taken.
6. Weather at the time of collection and particulars of recent rainfall, if any.
7. Does the water become affected in taste or odour after rainfall or under any
particular circumstances.
8. Are there any complaints from the consumers. If so, the nature of the complaint.
9. Character of surroundings and proximity to drains, cess pools, cattle sheds, manure
heaps, grave yard, bathing ghats and other sources of pollution.
10. Methods of purification and disinfection if any, details, dose of chemicals and
points of application.
B
(c) Nature of steining or casing and depth to which constructed and whether it is
in good condition.
(g) Whether the water is clear as it flows out of tube well and remains clear if
exposed to air (4-6 hours) or becomes discoloured and turbid.
(c) Is there any bathing ghat, boat jetty, burial ground and sewer outfall? If
upstream, give distance from sampling point.
Station
Date
Signature and name in block letters of the person collecting and forwarding the
samples.
204
SPECIMEN FORM FOR SHORT PHYSICAL AND CHEMICAL EXAMINATION
PHYSICAL Expressed as
0
1. Temperature C
2. Turbidity JTU
3. Colour Units of Pt.Co. scale
4. Taste and Odour Qualitative
Chemical
5. PH
6. Conductivity micromhos/cm
7. Free CO2 (mg/1) CO2
8. Alkalinity (mg/1) CaCO3
9. Chlorides (mg/1) C1
10. Nitrites (Qualitative)
11. Dissolved oxygen (mg/1)O
12. Hardness (mg/1) CaCO3
(a) Carborate
(b) Non-carbonate
(c) Total
13. Iron (mg/1)Fe
14. Fluorides (mg/1)F
15. Residual Chlorine (mg/1 C1
16. Alumina in Alum (%) A12O3
17. Available chlorine (%) C1
in Bleaching Powder
18. Coagulant Dose Jar Test (mg/1)
19. Chlorine Demand (mg/1) C1
Remarks :
Officer-in charge
Date
205
SPECIMAN FOR COMPLETE PHYSICAL, CHEMICAL AND BILOGICAL EXAMINAITON
Name and address of the Laboratory:
Name and Address of Sender Sender‟s No. Date of Collection………...............
PHYSICAL Expressed as
0
1. Temperature C
2. Turbidity JTU
3. Colour Units of Pt.Co. scale
4. Taste and Odour Qualitative
Chemical
5. PH
6. Conductivity micromhos/cm
7. Free CO2 (mg/1) CO2
8. Alkalinity (mg/1) CaCO3
(a) Pheno-phthalen
(b) Total
9. Chlorides (mg/1) C1
10. Ammonia (mg/1)N
(a) Free and Saline
(b) Albuminoid
11. Nitrites (mg/1) N
12. Nitrites (mg/1) N
13. Dissolved oxygen (mg/1) O
14. Oxygen absorbed at 27 oC (mg/1) O
(a) 3 minutes
(b) 4 hours
B.O.D. (mg/1) O
B.O.D. (mg/1) O
Hardness
(a) Carbonate
(b) Non-carbonate
(c) Total
Iron (mg/1) Fe
Manganese (mg/1) Mn
Fluorides (mg/1) F
Calcium (mg/1) C1
206
Magnesium (mg/1) Mg
Residual Chlorine (mg/1) C1
Sulphates (mg/1) SO4
Total Solids
(a) Dissolved
(b) Suspended
(c) Volatile
rks: Office-in-charge
SPECIMAN FORM FOR SHORT BACKTERIOLOGICAL EXAMINATION OF WATER
Remarks: Office-in-charge
208
SPECIMAN FORM FOR SHORT BACKTERIOLOGICAL EXAMINATION OF WATER
3. E. Coli MPN/100 ml
4. Completed Test
Date : Office-in-charge
209
ANNEXURE J (Refer clause 2.5.1.1, and 2.1.2.1)
PHYSICAL AND CHEMICAL PARAMETERS (as per IS: 10500-2012 (Second
Revision) )
(These standards are subject to change or revisions by Bureau Of Indian Standards from
Time to time )
Sr Characteristics Acceptable **Cause for Remarks
no Rejection
1. Turbidity (NTU) 1 5
2. Colour (Units on Platinum 5 15 Consumer acceptance decreases
cobalt scale Hazen Unit )
3. Taste and Odour Un Un Consumer acceptance
objectionable objectionable decreases
4. PH 6.5-8.5 6.5 -8.5 Water will affect the mucous
membrane & /water supply
system
5. Total dissolved solids 500 2000 Consumer acceptance
(mg/lt) decreases. Laxative effect upon
people who are not accustomed
to it. May cause gasto-intestinal
irritation.
6. Total hardness (as CaCO3) 200 600 Encrustation in water supply
(mg/lt) structure and adverse effects on
domestic use/scale formation
7. Chlorides (as C I) (mg / I) 250 1000 Taste, palatability and corrosion
are affected
8. Sulphates (as SO4) (mg/lt) 200 400 Causes Gastro intestinal
irritation
9. Flourides (as F) (mg/lt) 1.0 1.5 Results in dental/skeletal
fluorosis
10. Nitrates (as NO3) (mg/lt) 45 45 May cause
Methaemoglobineamia / blue
baby disease
11. Calcium (as Ca) (mg/lt) 75 200 Encrustation in water supply
12. Magnesium (as Mg) <30* 150 structure and adverse effects on
*If there are 250 mg/l domestic use
(mg/lt) of sulphates Mg
content can be
increased to a
maximum of 125mg/l
with the reduction of
Sulphates @ 1 unit per
every 2.5 units of
Sulphates
13. Iron (as Fe) mg/lt) 0.3 0.3 Taste & appearance are affected
and promotes iron bacteria &
adverse effect on domestic use
and water strips.
14. Alkalinity (mg/lt) 200 600 Water will affect the mucous
membrane &/ water supply
system, taste becomes
unpleasant.
15. Manganese as Mn mg/l 0.05 0.5
16. Copper as Cu mg/l 0.05 1.5
17. Zinc as Zn mg/l 5.0 15.0
18. Phenolic Compounds as 0.001 0.002
Phenol mg/l
19. Anionic detergents as 0.2 1.0
MBAS mg/l
20. Mineral Oil mg/l 0.01 0.3
210
21. Toxic Materials
22. Arsenic (as As) (mg/lt) 0.01 0.05
23. Pes icides (total, mg/lt) Absent 0.001 Water becomes toxic.
24. Cadmium as Cd mg/l 0.003 0.003
25. Chromium as Hexavalent 0.05 0.05
Chrome Cr^6 mg/l
26. Cyanide as CN mg/l 0.05 0.05
27. Lead as Pb mg/l 0.01 0.01
28. Selenium as Se mg/l 0.01 0.01
29. Mercury total as Hg mg/l 0.001 0.001
30. Polynuclear 0.2 micro g/l 0.2 micro g/l
aromaticHydrocarbons
(PAH)
31. RADIO ACTIVITY
32. Gross Alpha Activity 3 pCi/l 3 pCi/l pCi =pico curie
33. Gross Beta Activity 30 pCi/l 30pCi/l
34.
35. Residual free chlorine 0.2 1.0 To be applicable only when
(mg/lt) water is chlorinated. Tested at
consumer end. When protection
against viral infection is
required, it should be min. 0.5
mg/lt)
36. Bacteria (MPN/100ml) 0 0 Results in diarrhoea, decently,
typhoid etc
Notes : * The figures indicated under the column “Acceptable” are the limits upto
which water is generally acceptable to the consumers.
** Figures in excess of those mentioned under „Acceptable‟ render the water not acceptable,
but still may be tolerated in the absence of an alternative and better source but upto the limits
indicated under column “Cause for Rejection” above which the sources will have to be
rejected.
211
BACTERIOLOGICAL QUALITY OF DRINKING WATER
213
ANNEXURE-K (Refer Chapter 3.1)
POPULATION FORECAST EXAMPLE FOR CALCULATING
Data assumed
Using various methods the population for the design period is estimated and the realistic value
of population is selected for the design of the scheme.
1. INCREMENTAL INCREASE METHOD
Sr. Year of Population Increase/ Decade % Increase in Incremental
No. Census population Increase
1 1961 343 -- -- --
2 1971 589 246 71.72 --
3 1981 686 97 16.46 -149
4 1991 1087 401 58.45 +304
744 146.63 155
Population forecast can be calculated by using a software also. The results obtained from
software is appended and is in agreement with hand calculation.
Final Prediction:
The geometric progression gives too a high a value hence cannot be considered in the present
case. It gives a valve more than 2% annual growth. Considering 2% average national growth
per year; the population in 2021 will be 1880. Hence, arithmetical increase method gives the
nearest value. However, as there is a drastic change in population from 1981 to 1991 by nearly
100% in this particular case. Rural population growth during the decade 2001-2011 is 0.798%.
The design of rural water supply and sanitation schemes shall be based on actual
existing population with realistic projection for the project using the methods described above.
However, the per year growth rate must be taken @ 0.798 % per annum based on census
2011.
215
ANNEXURE-L (Clause 6.7.1 & 10.7)
Environmental Data Sheet for Water Supply and Sewerage Schemes for
DSR Stage
Format for Environmental Data Collection for Water Supply and Sewerage Schemes
1. GENERAL
1.1. Name of Village/Habitation:
1.2. Gram Panchayat
1.3. Block:
1.4. District:
1.5. Zone (North/Central/South)
2. BASELINE ENVIRONMENT
2.1. Topography
(Plain/Rolling/Hilly)
2.2. Type of Soil: Alluvial Silt Silty Clay
Sandy Sandy other
Clay
2.3. Intensity of Rainfall Low Mode High
rate
0
2.4. Temperature: Min: C Max:
216
Format for Environmental Data Collection for Water Supply and Sewerage Schemes
3. SOCIAL ENVIRONMENT
3.1. Population
3.2. Number of households
3.3. Land use pattern of village Rural Urbanized Rural
3.4. Historical/ Religious Yes No
Importance
3.5. Major Source of Income Agriculture Busines Service
s
Labor Others
3.6. Is the proposed project likely to affect any natural habitats/cultural Yes / No
properties?
3.6.1. If yes, whether appropriate safeguards are proposed? (Write note)
3.7. Is the proposed project likely to infringe on the rights of the local people, Yes / No
including traditional land water rights?
3.7.1. If yes, whether appropriate mitigation measures have been proposed?
(Write Note)
4. PUBLIC HEALTH ISSUES
4.1. Any incident of Waterborne Yes No
epidemic/ disease in the recent
past
4.1.1. If Yes: Name of diseases Diarrhea Gastro entities
(Waterborne)
Typhoid Others
4.2. Is there any vector borne disease Yes No
4.2.1. Name of Vector borne Malaria Dengu Filaria
disease e
5. WATER SUPPLY SCHEME
5.1. Type of Scheme Existing/New Scheme
5.1.1. Whether the proposed water Single Village Scheme Multi Village Scheme
supply scheme is
5.1.2. If new water Supply scheme
is proposed, briefly give data on
the current drinking water
situation
5.1.3. Source of drinking water River Lake Groundwater
supply: Canal Pond
5.1.4. Water availability in lpcd
5.1.5. Availability of Land for Panchayati Land Private Forest land
Intake/WTP site land
5.1.6. Has the source of water Yes No
quality been assessed, if yes
attach a copy of the test report.
5.1.7. Mention the appropriate Fluoride Iron Heavy Metals
nature of the quality problem
Bacteriological TDS Pesticide
Nitrate Others No Problem
5.1.8. Is there potential risk of contamination of source due to Yes / No
industrial contaminants, human waste discharge, solid waste
dumping, use of agro chemicals (Fertilizers, pesticides etc?)
5.1.8.1. If yes, whether appropriate preventive/ corrective actions
217
Format for Environmental Data Collection for Water Supply and Sewerage Schemes
taken? (Write a note)
5.1.9. Does the proposed project involve provision of any bore well Yes / No
within 1 km of international border between India and Pakistan?
5.1.9.1. If yes, the project cannot be sanctioned.
5.1.10. If Canal source, indicate the Slow Sand Filter (SSF) Rapid Sand Filter (RSF)
Treatment Technology proposed. Package Treatment Plant Any other method
5.1.11. If groundwater, indicate RtheO PlantTreatment De-fluoridation Plant (D F)
Technology proposed. Iron removal Plant Any other method.
5.1.12. Has disinfection system been provided □ Yes □ No
5.1.12.1. I
If yes, type of disinfection method (Silver Ionization or Chlorinator)
5.2. Provision Required from Generic EMF in the water supply scheme village
5.2.1. Air, Noise and water quality testing & rain water harvesting □ Yes □ No
5.2.2. Lawns and Tree Plantation in Water Works □ Yes □ No
5.3. Anticipated Environmental Issues and Mitigation Measures during implementation
5.4. Parameter Issue Mitigation measure
5.4.1. Water availability
5.4.2. Water quality
5.4.3. Sanitation
5.4.4. Construction
5.4.5. Disposal of construction wastes
6. SEWERAGE SCHEME
6.1. Whether Proposed Sewerage Single Village Scheme Multi Village Scheme
Scheme is
6.2. Current Sanitation Practices * Septic Tank Septic Tank with Soak Pits
Open Defecation Bore well/ soak pit type
Others
6.3. Usage of toilets in terms of
number and percentage
6.4. Percentage of households
having septic tanks*
6.5. Availability of water supply
in toilets
6.6. Current Drainage Pattern* Open Partially covered No Drainage
Drains with Open system
Drains
6.7. Does the wastewater from Yes No
cattle sheds discharged into
the open drains*
6.8. Does the grey water and Yes No
black water mix*
6.9. Villagers feedback about Satisfied Unsatisfied
current sanitation practice*
6.10. Approximate Wastewater
Quantity in mld
6.11. Method of treatment to
be Provided
6.11.1. Whether existing Ponds Yes No
will be used as STP
6.11.2. Pond‟s distance from the
nearest settlement (m)
218
Format for Environmental Data Collection for Water Supply and Sewerage Schemes
6.11.3. Whether distance from the nearest schools/primary health Yes No
center/religious structure is more than 200 m.
6.11.4. Water Quality of Pond by Good Very bad
visual inspection
6.11.5. Current use Cattle Irrigation Sewage Aquacu Any other
of Pond Wash Disposal lture
proposed for
STP
6.11.6. Is there any requirement of expansion of pond Yes No
to use as a STP
6.12. Yes No I
s there sufficient land available for expansion of
the pond or new STP
6.12.1. If yes, current land use Agriculture Barren Forest
land
6.13. Is there plantation around pond site/STP Yes No
6.14. Environmental Features around the new STP
site,
i. Approximate area of land in ha.
ii. Land use pattern
iii. Distance from the nearest water body
iv. Distance from the nearest settlement
v. Accessibility of area
vi. Is there stagnation of water takes place
(Yes/No)
6.15. Contamination of Drinking Water Source from Yes No
the Pond/STP
6.16. Disposal of Treated Effluent Inland On to land for
water body irrigation
6.17. Is there potential risk of contamination of source of water? If yes,
whatare the appropriate preventive/corrective actions taken? (write
note)
6.18.
Provision Required from Generic EMF in the Sewerage Scheme Village
6.18.1. Provision of Lawns and Tree Plantation at the STP Site water □ Yes □ No
works premises and STP site
6.18.2. Provision of Rainwater harvesting □ Yes □ No
6.18.3. Repair and Cleaning of Drains □ Yes □ No
6.18.4. Air, noise and water quality testing □ Yes □ No
6.18.5. Need of Public Awareness on health and hygiene □ Yes □ No
6.19. Anticipated Environmental Issues and Mitigation Measures during implementation
Parameter Issues Mitigation measure
6.19.1. Site selection of STP
6.19.2. Sewage Treatment
Technology
6.19.3. Disposal of Treated effluent
6.19.4. Disposal of Sludge
6.19.5. Construction Phase impacts
6.19.6. Disposal of Construction
debris
7. Whether Cleaning of Pond is Yes No
required
219
Format for Environmental Data Collection for Water Supply and Sewerage Schemes
Signature
JE/FE
EO/ EM/ Sr EM/ ES/ EMS
EE (Approval as per ES Recommendation)
SE
Note: * In case of multi-village scheme, please attach the data for each village separately.
220
ANNEXURE-M (Refer clause 4.12.1)
Data: A 15 cm. well penetrates 30m below static water level. After a long period of pumping
a rate of 1800 Ipm, the draw down in the observation wells at 12m and 36 m from the pumped
well are 1.2m and 0.5 m respectively.
Factors to be Determined from the data:
i) The transmissibility of the aquifer
ii) The draw down in the pumped well assuming R=300 m
iii) The specific capacity of the well.
Solution:
Assuming radial flow into the aquifer from Dupit‟s equation
Dupit‟s Eqn. Q = K (h22 – h12)
2.303 log 10 r2 r1
Where,
T = Transmissibility of the water table aquifer
H = Saturated thickness of the aquifer
R = Radius of influence
rw = Radius of the well
hw = Depth of water in the well during pumping
H-hw = the resultant draw down in the pumped
h1=H-S1 =30 –1.2 =28.8m, r1 =12m
h2=H-S2 =30 –0.5 =29.5m, r2 =36m
Q= 1800 Ipm K= co-efficient of permeability
221
Pump set to be provided for pumping at the rate of 360 Ltrs. per minutes against total head
involved to deliver water in the receiving tank.
222
Annexure N Clause 4.8.3
Table I showing Discharge of tube well corresponding to water head discharge
over 60 deg Vnotch in LPH
HEAD OVER V- NOTCH
mm 0 1 2 3 4 5 6 7 8 9
10 29 37 46 57 68 81 95 111 128 147
20 167 188 211 236 263 291 321 353 386 422
30 459 498 540 583 628 675 724 776 829 885
40 943 1003 1065 1130 1196 1266 1337 1411 1487 1566
50 1647 1730 1817 1905 1996 2090 2186 2285 2387 2491
60 2598 2707 2820 2935 3053 3173 3297 3423 3552 3684
70 3819 3957 4098 4242 4388 4538 4691 4847 5006 5168
80 5333 5501 5672 5847 6025 6206 6390 6577 6768 6962
90 7159 7359 7563 7770 7981 8195 8414 8633 8857 9085
100 9316 9551 9789 10031 10276 10525 10777 11033 11293 11556
110 11823 12093 12367 12645 12927 13212 13501 13794 14091 14391
120 14696 15004 15316 15631 15951 16275 16602 16933 17269 17608
130 17951 18298 18650 19005 19364 19727 20095 20466 20842 21221
140 21605 21993 22385 22781 23181 23586 23995 24408 24825 25246
150 25672 26102 26336 26975 27418 27865 28317 28773 29233 26698
223
Table –II
DISCHARGE OVER 90 deg. V- NOTCH
(Liters per hour)
224
Table – 1 A
225
Table – II A
226
Annexure „O‟
Note: Designs as per Standard DSRs will be made part after finalization by
Consultant being hired for preparation of DSRs.
227
DRAWINGS
228
229
230
231
233
235
236
239
240
242
243
244
245
246
247
248
252
253
254
255
256
257
260
261
262
263
266
267
Abbreviation
BF Butterfly
BOD : Biochemical Oxygen Demand
BW/OW : Bore well / Open well
COD : Chemical Oxygen Demand
CPHEEO : Central Public Health Environmental Engineering Organisation
EDS : Environment Data Sheet
ELSR/ESR : Elevated Service Reservoir
EMF : Environment Management Framework
EMP : Environment Management Plan
GI : Galvanized Iron
GP : Gram Panchayat
GPWSC : Gram Panchayat Water and Sanitation Committee
HDPE : High Density Poly Ethylene
MBR : Membrane Bio Reactor
MOV : Valve Actuator Drive
OHSR : Over Head Service Reservoir
PLC : Programme Logic Controller
PSEB : Punjab State Electricity Board
RCC : Reinforced Cement Concrete
RSC : Residual Sodium Carbonate
RTU : Remote Terminal Unit
SAR : Sodium Adsorption Ratio
SCADA : Supervisory Control and Data Acquisition
SEA : Sector Environment Assessment
S&S : Storage & Sedimentation
TDS : Total Dissolved Solids
TPPFL : Twin Pit Pour Flush Latrine
T/W : Tubewell
uPVC : Un-plasticized Poly Vinyl Chloride
WSSD : Water Supply and Sanitation Department
268
References:
269