SEASON: AW’ 07

PRODUCT PACK - DRESS SHIRTS

PRODUCT: REGULAR COLLAR WITH ROUND CUFF CONTENTS

PRODUCT DETAILS 1
STYLE NO. RAY 001 STYLE LINES 2
BLOCK DETAILS, SPEC SHEET &
MEASUREMENT GUIDELINE 3
CONSTRUCTION DETAILS 4-8
BUTTON PLACEMENTS 9
100 % COTTON FABRICS LABEL PLACEMENTS 10
FABRIC 100% LINEN FABRICS FOLDING & PACKING 11
TRIM LIST 12

Department Approved by: Signature Date:

Product

Sourcing

Quality

N.B.: Any amendment should be in consultation/agreement between all the departments

mentioned above.

Any queries regarding the product pack can be marked to product department on the following address: STYLE LAB
Style lab,Raymond Apparel Ltd., Jekegram, Pokhran Road no.1, Thane-400606 , RAYMOND APPAREL LIMITED.
Mahrashtra, India. Ph: 25988050,25988015. Jekegram Thane.
STYLE LINE RAY 001
2

LONG SLEEVES DRESS SHIRT WITH

REGULAR COLLAR ROUND CUFF.

Garment style lines: Double fused Regular

collar with Removable collar stays. Round
42
corner Pocket , Convertible Barrel cuffs,
fused cut & sew center placket.

SPI 18 for all top stitches

Thread: 150tkt PPC spun

Body & Button Hole thread to be DTM to

basie fabric. Button & main label threads
to be DTM to button & main label
respectively.

Buttons : 16L & 14L, 4 hole DTM

Buttons. ( P0428/P695., P0839/P6957).
For DTM & Button Type refer to trim card
THREAD: 95m. For Branding Embroidery
thread to be Madeira Poly neon / Calypso:
3 Mrts.

INTERLINING: 25cm (90cm width)

Collar Skin, Band & Cuff - DHJ 285 ES
Consumption : 17cm., Collar Patch &
Placket - DHJ Polystar 2.28.23.464 ES
Consumption : 8cm

STYLE LAB
RAYMOND APPAREL LIMITED.
Jekegram Thane.
STYLE LINE RAY 001
2.1

SHORT SLEEVES DRESS SHIRT WITH

REGULAR COLLAR ROUND CUFF.

Garment style lines: Double fused Regular

collar with Removable collar stays. Round
corner Pocket , fused cut & sew center
42
placket.

SPI 18 for all top stitches

Thread: 150tkt PPC spun

Body & Button Hole thread to be DTM to

basic fabric. Button & main label threads
to be DTM to button & main label
respectively.

Buttons : 16L & 14L, 4 hole DTM

Buttons. ( P0428/P695., P0839/P6957).
For DTM & Button Type refer to trim card
THREAD: 75m. For Branding Embroidery
thread to be Madeira Poly neon / Calypso:
3 Mrts.

INTERLINING: 20cm (90cm width)

Collar Skin, Band & Cuff - DHJ 285 ES
Consumption : 12cm. Collar Patch &
Placket - DHJ Polystar 2.28.23.464 ES
Consumption : 8cm

STYLE LAB
RAYMOND APPAREL LIMITED.
Jekegram Thane.
BLOCK DETAILS, SPEC SHEET & MEASUREMENTS GUIDE LINES
RAY 001
3

BLOCK DETAILS: Body: Raymond ; Collar: C-01 RY REGULAR; C-band: CB-01 RY Pocket: PK-01 RY . MESUREMENT GUIDELINE
SPEC SHEET Cuff: CF 00 RY

Size 5
Code Description Tol (+/-)
39 40 42 44 46
1 Collar button to buttonhole. 39.50 40.50 42.50 44.50 46.50 0.50
1
2 Collar Height at CB 4.50 4.50 4.50 4.50 4.50 0.00
3 Collarband height at CB 3.50 3.50 3.50 3.50 3.50 0.00 4 6 2 8
4 Collar point 7.50 7.50 7.50 7.50 7.50 0.00 3
5 tie space 0.50 0.50 0.50 0.50 0.50 0.20 7 22
6 Collar bottom measurement 39.00 40.00 42.00 44.00 46.00 0.30
7 Collar band bottom measurement 43.70 44.70 46.70 48.70 50.70 0.30 23
8 Collar spread 10.50 10.50 10.50 10.50 10.50 0.70 19
20
9 1/2 Chest 58.50 60.00 63.00 66.00 69.00 1.00
10 1/2 Waist 55.50 57.00 60.00 63.00 66.00 1.00 15
14
11 1/2 Bottom 56.50 58.00 61.00 64.00 67.00 1.00 17
12 CB length 79.50 80.00 81.00 82.00 83.00 1.00 16
13 CF length band dow n 69.90 70.30 71.10 71.90 72.70 1.00
14 Yoke height at CB 11.50 11.50 11.50 11.50 11.50 0.30 9 18
12
15 Back Shoulder Length 47.25 48.00 49.50 51.00 52.50 0.50
16 1/2 Armhole Curve 26.50 27.00 28.00 29.00 30.00 0.50 20 cm 13
17 Long Sleeve Length From C.B.N 87.38 88.00 89.25 90.50 90.75 1.00 10
18 Sleeve Length from shoulder 63.75 64.00 64.50 65.00 64.50 1.00 21
19 Cuff length 24.50 25.00 26.00 27.00 28.00 0.50
20 cuff height 7.00 7.00 7.00 7.00 7.00 0.00
11
21 1/2 Cuff Length Closed 11.00 11.25 11.75 12.25 12.75 0.30
22 Pocket from shoulder seam 21.50 22.00 22.00 22.50 22.50 0.50
23 Pocket from CF 4.50 5.00 5.00 5.50 5.50 0.50

NOTE: 1. Chest (at armhole), waist, & bottom measurements are with seam pressed back, from 3. All measurements are in centimetres.
edge to edge as shown in fig alongside
2. Collar btn to btnhole measurement is from inside of buttonhole bar to centre of button.
BLOCK DETAILS, SPEC SHEET & MEASUREMENT GUIDELINE RAY 001
3.1

BLOCK DETAILS: Body: Raymond ; Collar: C-01 RY REGULAR; C-band: CB-01 RY Pocket: PK-01RY MESUREMENT GUIDELINE
SPEC SHEET
5
Cod Size
Description Tol (+/-)
e 39 40 42 44 46
1 Collar button to buttonhole. 39.50 40.50 42.50 44.50 46.50 0.50 1
2 Collar Height at CB 4.50 4.50 4.50 4.50 4.50 0.00 4 6 2 8
3 Collarband height at CB 3.50 3.50 3.50 3.50 3.50 0.00
3
4 Collar point 7.50 7.50 7.50 7.50 7.50 0.00
7 20
5 tie space 0.50 0.50 0.50 0.50 0.50 0.20
6 Collar bottom measurement 39.00 40.00 42.00 44.00 46.00 0.30
21
7 Collar band bottom measurement 43.70 44.70 46.70 48.70 50.70 0.30
8 Collar spread 10.50 10.50 10.50 10.50 10.50 0.70
9 1/2 Chest 58.50 60.00 63.00 66.00 69.00 1.00
15
10 1/2 Waist 56.50 57.00 60.00 63.00 66.00 1.00 14
19
11 1/2 Bottom 56.50 58.00 61.00 64.00 67.00 1.00
12 CB length 79.50 80.00 81.00 82.00 83.00 1.00 16 18
13 CF length band dow n 69.90 70.30 71.10 71.90 72.70 1.00
14 Yoke height at CB 11.50 11.50 11.50 11.50 11.50 0.30
9
12
15 Back Shoulder Length 47.25 48.00 49.50 51.00 52.50 0.50 20 cm
17
16 1/2 Armhole Curve 26.50 27.00 28.00 29.00 30.00 0.50 13
17 Sleeve Opening Round 37.00 38.00 40.00 42.00 44.00 0.50 10
18 Sleeve Length from shoulder 23.50 24.00 25.00 26.00 27.00 1.00
19 Sleeve Length from CBN 47.13 48.00 49.75 51.50 53.25 0.50
20 Pocket from shoulder seam 21.50 22.00 22.00 22.50 22.50 0.50
11
21 Pocket from CF 4.50 5.00 5.00 5.50 5.50 0.50

NOTE: 1. Chest (at armhole), waist, & bottom measurements are with pressed back, from 3. All measurements are in centimetres.
edge to edge as shown in fig alongside
2. Collar btn to btnhole measurement is from inside of buttonhole bar to centre of button.
CONSTRUCTION DETAILS - COLLAR & COLLAR BAND RAY 001
4

FABRIC 3mm fabric COLLAR - C 01 RY

SKIN allowance
PATCH

6mm 1.5mm runstitch 8.1 cm trimmed

Collar point
5mm breakline 7.5cm finished
Collar point
6mm


6mm trim allowance

INTERLINING CUTTING DETAILS
COLLAR SKIN - cut on true bias 45 degree
2.5 cm leg COLLAR PATCH - cut on grain
BREAK LINE COLLAR BAND - cut on true bias 45 degree
FINISH LINE CUFF - cut on grain
CENTRE PLACKET - cut on grain
TRIM LINE
3mm fabric allowance

COLLARBAND - CB 01RY

6mm
1cm

FINISH LINE
CONSTRUCTION DETAILS - COLLAR & COLLAR BAND RAY 001
5

COLLAR - C 01 RY
5 mm
COLLARBAND - CB 01 RY
1mm

Top stitch band & lock here.

Begin ‘finish collar’ here & end on
same point on the other side
Back tack ends.

5 mm 1mm

2.5”x3/8”x0.35mm Branded Nylon collar Stays

CONSTRUCTION DETAILS - CUFF RAY 001
7

1.5cm fabric allowance

FABRIC SKIN

CUFF - CF-00 RY

6mm 3mm
1.5mm runstitch

4mm fabric allowance

1mm cuff attach

1cm

Lock here, towards the

button side of cuff

5 mm stitch
CONSTRUCTION DETAILS - POCKET, FRONTS & BACK RAY 001
6

6mm L & R FRONTS

2.5 cm

5 mm
1mm POCKET - PK 01 RY 14 cm

2.5cm 5 mm

3.5cm
13 cm
1cm full roled 3.5cm
hem
For Both L/S &

4-5 stitches backtack

1mm 5 mm

1 cm

YOKE & BACK

1 cm

NO PLEAT AT BACK 3.5cm

2 cm
CONSTRUCTION DETAILS - SLEEVE & SLEEVE PLACKET RAY 001
8

1.25 cm
ATTACH SLEEVE TO BODY
UPPER & UNDER SLEEVE PLACKET

Body 2.5 cm

Start here with 3 stitches to lock

16.5 cm
2 cm
Hem Detail For S/S Shirt
1.25 cm 2.3cm
SNCS

Sleeve 1mm

2.5 cm
1.0 cm
1.25 cm hem
1mm height
1.0 cm
TOPSTITCH SLEEVE Body
2.5 cm

1.0 cm

5mm or 3/16”
gauge
SIDE SEAM

SNCS

Sleeve
Side seam: Feed of the arm, front. over back
SNCS on both sides.
DNCS
BUTTON PLACEMENTS
RAY 001
9

FOR BUTTON TYPE & LIGNE

BUTTON PLACEMENTS REFER TO TRIM CARD
Collar btn to be in line withbtns on placket.
Adjust slightly to maintain vertical line balancing in
plaid & striped fabrics

6.5 cm
9.0 cm

9.0 cm cm 1.45 cm to outer edge of

1.75 cm Button hole bar

Last button hole is horizontal 6.3 cm

Spare buttons
1.5 cm
7.5 cm All button holes to have Purl 6.3 cm
stitch formation

1.75 cm All btns to be sewn with cross 2.5 cm

1.75 cm lock stitch. Button sew thread
to be dtm to button. 4.5 cm
Provide adequate stemming
to buttons.
16L buttons 7 + 1
14L buttons 2+1
1.0 cm to outer edge of
Button hole bar
NOTE: Sew 16L Buttons with laser Branding on wearer’s Right cuff.
LABEL PLACEMENTS
RAY 001
10

4
40cm 3.5cms, centered at CB to center of the
4.5 cm 3.5 cm embroidery & Thread as for the DTM ( Thread to
be used Poly neon)

Wash Care label to be inserted

Left Wearer side inside the Feed of the arm.
Egyptian Giza Cotton

Only for 100% Cotton Fabrics Wash care

10 cm

1.5 cm
FOLDING & PACKGING RAY 001
11

FOR TAGS REFER TO TRIM CARDS Insert 1-Pearl head

2-Metal cross clip to hold pin and 1-White
Raymond Back Supporter
tail ( one end inserted in Plastic “M-clip” to
hole of back support) hold sleeves inside
42

TUCK IN TAIL
Pearl-head pins to be (Tail to be laid
inserted from the top of the flat inside)
back support Two long printed
tissue paper BOPP
Poly bag to be used.

co r
ta de
Ba
1-Metal cross clip to 36cm (+/-0.3)

g
hold cuff, to be

Spa envelo
stay
placed beneath Hang tag to be put on 1st

re c
olla e
sleeve placket & Bar Code Tag &

r
button hole ( excluding

p
Spare Collar Stay
Han

cuff . neck button)

Envelope on last but
g Ta

NOT TO BE VISIBLE Using Branded locking

EITHER ON FRONT one button
g

OR BACK loop

23 cm (+/-0.3)
PVC band dented
Cuff to be aligned with side towards CF Cardboard neckband, longer 1-silver plastic head
COLLAR SIZE TAB
bottom of board TO BE STUCKED IN THE CENTER edge up pin at neck band, tuck
OF THE COLLAR in-out-in with~1.5cm
Branded collar Strip Blend label
bite outside
to be inserted under
40

PVC band
40

042 R BUTTERFLY Bottom edge of band to be

Note: Metal clips -made of rust proof non corrosive metal with smooth edges.
Metal pins -made of rust proof non corrosive with plastic silver head aligned after pinning
FOLDING & PACKGING
RAY 001
11.1

FOR TAGS REFER TO TRIM CARDS Insert 1-Pearl head

2-Metal cross clip to hold pin and 1-White
Raymond Back Supporter
tail ( one end inserted in Plastic “M-clip” to
hole of back support) hold sleeves inside
42

TUCK IN TAIL
Pearl-head pins to be (Tail to be laid
inserted from the top of the flat inside)
back support
Two long printed
tissue paper BOPP
Poly bag to be used.

co r
ta de
Ba

g
36cm (+/-0.3)

Spa envelo
stay
re c
1-Metal cross clip Hang tag to be put on 1st

olla e
Bar Code Tag &

r
button hole ( excluding

p
to hold sleeve Spare Collar Stay
Han

NOT TO BE VISIBLE ON neck button)

Envelope on last but
g Ta

BACK Using Branded locking

one button
g

loop

23 cm (+/-0.3)
PVC band dented
Cuff to be aligned with side towards CF Cardboard neckband, longer 1-silver plastic head
COLLAR SIZE TAB
bottom of board TO BE STUCKED IN THE CENTER edge up pin at neck band, tuck
OF THE COLLAR in-out-in with~1.5cm
Branded collar Strip Blend label
bite outside
to be inserted under
40

PVC band
40

042 R BUTTERFLY Bottom edge of band to be

Note: Metal clips -made of rust proof non corrosive metal with smooth edges.
Metal pins -made of rust proof non corrosive with plastic silver head aligned after pinning