Professional Documents
Culture Documents
Intertuf 654: Bleached Epoxy
Intertuf 654: Bleached Epoxy
Bleached Epoxy
PRODUCT DESCRIPTION A two-pack, bleached epoxy anticorrosive coating that is light in colour and is approved for the carriage of grain
when used as part of an approved scheme.
INTENDED USES For use in cargo holds, cofferdams and dry spaces where a light coloured coating is required.
For use at Newbuilding or Maintenance & Repair.
Intertuf 654 48 hrs 28 days 40 hrs 28 days 24 hrs 28 days 16 hrs 14 days
Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation
depending on factors such as differences in colour and normal manufacturing tolerances.
Marine Coatings
Page 1 of 4
Issue Date:07/07/2009
Ref:663
Intertuf 654
Bleached Epoxy
CERTIFICATION When used as part of an approved scheme, this material has the following certification:
SYSTEMS AND Consult your International Paint representative for the system best suited for the surfaces to be protected.
COMPATIBILITY
NEWBUILDING
Where necessary, remove weld spatter and smooth weld seams and sharp edges.
Weld seams and damaged areas should be blast cleaned to Sa2½ (ISO 8501-1:2007) or power tooled to Pt3 (JSRA
SPSS:1984)
If the shop primer shows extensive or widely scattered breakdown, overall sweep blasting may be necessary.
For zinc and unapproved shop primers, grit sweep to AS2 or AS3 International Paint Sweep Blasting Standards or
power tool to Pt3 (JSRA SPSS:1984).
MAJOR REFURBISHMENT
Abrasive blast clean to Sa2½ (ISO 8501-1:2007). If oxidation has occurred between blasting and application of
Intertuf 654, the surface should be reblasted to the specified visual standard.
Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate
manner.
REPAIR
Prepare corroded areas by grit blasting to Sa½ (ISO 8501-1:2007) or power tooling to St3 (ISO 8501-1:2007).
Loose or flaking coatings should be removed back to a firm edge and Intertuf 654 should be applied to overlap the
existing coating by 2-3 centimetres (one inch) .
For blasted areas, Intertuf 654 should be applied before oxidation occurs. If oxidation does occur, the entire
oxidised area should be reblasted to the specified standard above.
Intertuf 654 can be applied over Intergard 269, when used as a holding primer to protect the blast. The primer
surface should be dry and free from all contamination and Intertuf 654 must be applied within the overcoating
interval specified (consult the Intergard 269 product data sheet).
OTHER
For tank coating projects, consult International Paint for the detailed tank coating procedures that should be
followed.
NOTE:
For use in Marine situations in North America, the following surface preparation standards can be used:
SSPC-SP10 in place of Sa2½ (ISO 8501-1:2007)
SSPC-SP3 in place of St3 (ISO 8501-1:2007)
Marine Coatings
Page 2 of 4
Issue Date:07/07/2009
Ref:663
Intertuf 654
Bleached Epoxy
APPLICATION
Mixing Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the
unit has been mixed it must be used within the working pot life specified.
(1) Agitate Base (Part A) with power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.
Thinner Not Recommended. Use International GTA220 only in exceptional circumstances (max 5% by volume). DO NOT
thin more than allowed by local environmental legislation.
Airless Spray Recommended
Tip Range 0.53-0.66 mm (21-26 thou)
Total output fluid pressure at spray tip not less than 176 kg/cm² (2500 p.s.i.)
Conventional Spray Application by conventional spray is not recommended.
Brush Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified
film thickness.
Roller Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified
film thickness.
Cleaner International GTA822
Work Stoppages and Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with
Cleanup International GTA822. Once units of paint have been mixed they should not be resealed and it is advised that
after prolonged stoppages work recommences with freshly mixed units.
Clean all equipment immediately after use with International GTA822. It is good working practice to periodically
flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount
sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations.
All surplus materials and empty containers should be disposed of in accordance with appropriate regional
regulations/legislation.
Welding In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be
emitted which will require the use of appropriate personal protective equipment and adequate local exhaust
ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and
Cutting."
SAFETY All work involving the application and use of this product should be performed in compliance with all
relevant national Health, Safety & Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health
and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and
container labels. If you do not fully understand these warnings and instructions or if you can not strictly
comply with them, do not use this product. Proper ventilation and protective measures must be provided
during application and drying to keep solvent vapour concentrations within safe limits and to protect
against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves,
goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods
and work environment.
EMERGENCY CONTACT NUMBERS:
USA/Canada - Medical Advisory Number 1-800-854-6813
Europe - Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191
R.O.W. - Contact Regional Office
Marine Coatings
Page 3 of 4
Issue Date:07/07/2009
Ref:663
Intertuf 654
Bleached Epoxy
LIMITATIONS This product will not cure adequately below 5°C. For maximum performance ambient curing temperatures should be
above 10°C.
Drying times and overcoating intervals may alter due to on-site factors such as tank configuration or ventilation rates
etc.
Optimum performance is achieved when Intertuf 654 is applied over blasted steel.
Consult International Paint for the time interval required between coating completion and cargo loading.
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate
and environmental conditions. Consult your local International Paint representative for specific recommendations.
Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For
optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing
and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance
with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the
purpose of establishing a general guideline of the coating application procedures. Test performance results were
obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published
test results, or any other tests, accurately represent results found in all field environments. As application,
environmental and design factors can vary significantly, due care should be exercised in the selection, verification of
performance and use of the coating.
STORAGE Shelf Life 12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded
conditions away from sources of heat and ignition.
IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically
recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at
their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but
we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless
we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent
permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by
operation of law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied
and technical advice given are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information
contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's
responsibility to check with their local International Paint representative that this data sheet is current prior to using the product.
and product names mentioned in this data sheet are trademarks of, or are licensed to, AkzoNobel.
© AkzoNobel, 2009
www.international-marine.com
Marine Coatings
Page 4 of 4
Issue Date:07/07/2009
Ref:663