Professional Documents
Culture Documents
CFD Analysis of Ventilation System For An Engine Room: December 2016
CFD Analysis of Ventilation System For An Engine Room: December 2016
net/publication/312289286
CITATIONS READS
0 1,638
2 authors:
Some of the authors of this publication are also working on these related projects:
TWO PHASE FLOW SEPARATION IN A HORIZONTAL SEPARATOR BY INLET DIVERTER PLATE IN OILFIELD INDUSTRIES View project
All content following this page was uploaded by Seyfettin Bayraktar on 13 January 2017.
ABSTRACT
Engine room of marine vessels are equipped with ventilation system which provide fresh air
for properly oil burning in the combustion engines and to remove unwanted heat from the
main engines, auxiliary generators and other heat sources. In addition to this keeping the
temperature within allowed values is necessary for crews` optimum working conditions. In
the present paper, the ventilation system of the engine room of an ASD tug built by
SANMAR Shipyard is investigated. Temperature distribution in the engine room is measured
experimentally during her sea trial at full speed condition and then compared with the
numerical studies performed by computational fluid dynamics (CFD). It is seen that the
developed numerical model is in good agreement with the experimental data.
1. Introduction
Engine room is one of the important compartment in marine vessel due to contain vital
equipment which have different features and functions to move and bring operational
capability to the ships. These major equipment require both piping and ventilation system to
start operation. Particularly ventilation system have significant responsibility in terms of
directly influence on engine room equipment performance, lifetime and crew working
environment.
The primary mission of a well-designed ventilation system provide fresh air for properly oil
burning in the combustion engines and to remove unwanted heat from the main engines,
auxiliary generators and other heat sources. The volume of the air to be supplied is
determined from sum of airflow for combustion and airflow for evacuation of heat emission.
In addition to that keeping the temperature within allowed values is necessary for crew
optimum working condition. For example, the temperature of the main engine room cannot
be higher than 35 ºC according to ISO 8861:1998 [1]. Due to such strict standard international
institutions, organizations and engine suppliers recommend to consider the conditions given
in Table 1 that shows that 60% tropical ambient relative humidity at 45 ºC is the absolute
limit for humans to survive in the theory. For winter conditions, density of the air will
increase and consequently compression and maximum firing pressure will be increase too.
In order to prevent undesirably high pressure at low temperature, the turbocharger air inlet
temperature should be kept as high as possible.
1 SANMAR Shipyards, Design Department, Tel: +90 216 458 59 00, e-mail: [email protected]
2 Yıldız Technical University, Department of Naval Architecture and Marine Engineering, Faculty of Naval
Architecture and Maritime, Tel: +90 212 383 70 70, e-mail: [email protected]
Table 1. Ambient reference conditions for engine room environment
Engine manufactures [5] generally provide information about the ventilation system. For
instance, Caterpillar highly recommends that engine room temperature should be kept below
49 ºC otherwise amount of necessary fresh air should be taken directly from outside.
However, it should never below 5 ºC which can be achieved by stopping one or more air
supply fan. Fresh air inlet should be ducted away from the heat source and should be
discharged as low as possible towards the floor level while exhaust opening will be placed at
the top of the engine room. It is required that the position of the air inlet louvre should be
arranged to avoid the suction of exhaust gas into the engine room. Combustion air
temperature is one of the most important parameters that affects engine efficiency,
maintenance interval and exhaust gas amount. Table 2 shows the effect of the air temperature
for main engine performance.
Temperature,ºC
CFD has been used more extensively nowadays with a rapidly increasing trend in a wide
variety of engineering fields and industry such as automotive, medical research, aerospace
and maritime. Doğrul et al. [6] used a CFD to model heat, ventilation and air conditioning
(HVAC) unit in a room for performance analysis. Standard k-ε model used to show how air
conditioner location effect the air ventilation and distribution of the room. Kılıç and Sevilgen
et al [7] investigated the radiator heated room air flow and temperature distribution with RNG
k-ε model which demonstrate compliance for turbulence model. Newton and Lewis et al [8]
simulate thermal profile of engine room not only with CFD analysis, but also make
measurements on board to validate experiment results. Jian, Hongjuan and Yiping et al [9]
perform CFD analysis to show temperature field and velocity field distribution for bulldozer
cab by different types of air supply. RNG k-ε model and SIMPLE algorithm is used to solve
governing equations.
Sun et al., 2013 [10] used a CFD model to investigate the dense gas dispersion of liquefied
natural gas (LNG). Field measurements show that the CFD model can be used to predict the
dispersion with 19.62% error.
Temperature distribution prediction with CFD in the engine room of a catamaran type ship
was reported by Newton et al., 2014 [11]. The numerical analyses and field measurements
directed that the performance of the vessel in extreme climates would be increased if the
existent of the ventilation system of the ship had been improved since the installed system
was inappropriate.
A recent study on the gas dispersion in a ship engine room has been published by Li et al.,
2016 [12]. It was showed that the gas dispersion depends on multiple parameters and under
the impact of the air flow; temperature gradient and gas-buoyancy, natural gas tends to
accumulate on the top of the engine room.
The literature survey reveals that the studies on the temperature distribution and air flow in a
ship engine room is rare. Actually only the study of Newton et al., 2014 was reported on the
topic directly. Therefore, the objective of this study is to develop a CFD model to compute
the temperature and flow fields to use during the design of the engine room for better working
conditions and supplying the air in appropriate amount and temperature.
2. Engine room
The boat under consideration is an ASD tug built by Sanmar Shipyard. The length and
moulded beam of the tugboat is 24 m and 11 m, respectively. She gives a bollard pull of 60
tons. Main propulsion consist of a pair Caterpillar 3512C diesel engine, each has a capacity
of 1765 kw at 1600 rpm, and each driving with Rolls-Royce Z-drive. The dimensions of the
section of the engine room to evaluate the performance of the current ventilation system are
approximately 10.1xx11yx3z m3 where x, y and z show the longitudinal, spanwise and
normal-directions, respectively. There are two inlet and outlets to and from the engine room
to intake the fresh air and polluted air in the engine room. The ducts deliver air from the fan
intake grills to the inside of engine room is showed in Figure 1. Branches for the supply air
are designed as short as possible in order to minimize effect of the backpressure. The
openings of the supply ducts are arranged to:
The general overview of the engine room with the fresh air and turbocharger inlets are
showed in Figure 2.
In the present paper, Boğaçay class ASD tug built by Sanmar Shipyard is investigated.
Tugboat has 24 m length with a moulded beam at 11 m. She gives a bollard pull of 60 tonnes.
Main propulsion consist of a pair Caterpillar 3512C diesel engine, each has a capacity of
1765 kw at 1600 rpm, and each driving with Rolls-Royce Z-drive[13]. Necessary combustion
air requirement for each main engine is 2.83 m/s at full load and the related heat radiation to
surrounding medium is 119 kW. Despite having two generator in engine room, one of them
taking into account for CFD analysis because under normal conditions other one is keeping
as a stand-by. Each generator need 0.08 m/s air for combustion process and the generated
heat radiation is 23.2 kW [14]. According to ISO: 8861 the maximum theoretical air
requirement is calculated as 38000 m3/h and two centrifugal axial fan provided for ventilation
system both has a 40000 m3/h capacity.
For simulation 3-D simplified working domain (Figure 3) is modelled with RHINO Ceros
software. This domain include a pair of diesel engines, generators and exhaust system for
main engine. Relatively small heat radiation value of having pumps, electric panels and other
equipment are neglected.
The grid generation is the most important step that defines the cells to calculate flow variables
for dedicated computational domain. The engine room is meshed with approximately one
million elements as illustrated in Figure 4.
(a) (b)
Figure 4. Mesh structure on the working domain (a) and main engines, generator sets and
exhaust pipes (b).
Flow and temperature distribution in the engine room are governed by conservation of mass,
momentum and energy laws. Finite volume method has been used for discretization scheme.
The flow is considered steady, turbulent, incompressible and three-dimensional (3D).
Standard k-ε (SKE) model is used for modelling turbulent flow to show path lines, velocity
and temperature fields. The objective of the study is to determine the air and temperature
distributions in the engine room to improve thermal comfort and engine efficiency. The SKE
model which is based on the model transport equation for the kinetic energy (k) and its
dissipation (ε). The governing equations are stated below for mass conservation (Eq.1),
momentum equation (Eq.2), turbulence kinetic energy (Eq.3) and its distribution (Eq.4):
𝜕𝜌
+ 𝛻 × (𝜌𝑢) = 0 (1)
𝜕𝑡
𝜕(𝜌𝑢)
+ 𝛻 × (𝜌𝑢𝑢) = −𝛻𝑝 + 𝜌𝑔 + 𝛻 × (𝜇𝛻𝑢) − 𝛻 × 𝜏𝑡 (2)
𝜕𝑡
where p is the pressure, g is gravitational acceleration,µ is dynamic viscosity of fluid and
𝜏𝑡 is the divergence of the turbulence stress.
𝜕(𝜌𝑘) 𝜕(𝜌𝑢𝑘) 𝜕 𝜇𝑡 𝜕𝑘
+ = [𝜇 + ] + 𝜇𝑡 𝐺 − 𝜌𝜀 + 𝑆𝑘,𝑝 (3)
𝜕𝑡 𝜕𝑥 𝜕𝑥 𝑃𝑟𝑘 𝜕𝑥
𝜕(𝜌𝜀) 𝜕(𝜌𝑢𝜀) 𝜕 𝜇 𝑇 𝜕𝜀 𝜀
+ = [𝜇 + ] + [𝐶 𝜇 𝐺 − 𝐶2 𝜌𝜀] + 𝑆𝜀,𝑝 (4)
𝜕𝑡 𝜕𝑥 𝜕𝑥 𝑃𝑟𝜀 𝜕𝑥 𝑘 1 𝑇
In above equations, C1 and C2 are empirical model constants; Pr is represents Prandtl numbers
for kinetic energy; S is user-defined source term; and turbulence kinetic energy (G) calculated
as in Eq.5:
The governing equations are solved using Semi-Implicit Method for Pressure-Linked
Equation (SIMPLE) algorithm for steady-state analysis with second-order discretization for
the momentum equation and second-order upwind for the turbulent kinetic energy.
Continuity and Navier-Stokes equations need appropriate initial and boundary conditions to
be applied for solving process. For this reason velocity inlet boundary conditions are used
for air inlet ducts to represent uniform air flow to engine room while pressure outlet boundary
conditions are applied to funnel exhaust louvre to interpret as the static pressure of the
environment. Effect of the heat conduction from main engine, auxiliary engine and exhaust
pipe to engine room environment is represented with solid zone boundary conditions which
require material type and volumetric heat generation rate (heat source). Steel plates of the
surrounding engine room is represented as a wall boundary condition.
The solution is seen converged when the continuity residual is lower than 10 -3 while the rest
of residual are lower than 10-6.
Experimental data is gathered when tugboat in the sea trial for endurance test at full speed
condition for six hours. This ensures the engine room temperature and air flow distribution
to reach steady-state condition. Simple branch and rectangular section used for distribution
of inlet air in engine room. Table 3 shows the measurement data from the sea trail. Because
of the resistive losses, provided total air is measured approximately 34060 m 3/h for both
starboard and portside in the engine room.
Table 3. Air flow capacity for inlet duct during the sea-trial tests.
Figure 6 shows temperature the contours on the main engines, generator sets and exhaust
pipes. It is seen that the front surfaces of the main engine is cooler than the rear of it. It is not
surprising since relatively cooler air inlets from the inlets planes of the engines and keeps it
cooler. The similar result was concluded by Newton et al., 2014. Temperature on both the
engines and exhaust pipes are very close to the measured temperatures during the sea-trials.
Figure 6. Temperature distribution on the main engines, generator sets and exhaust pipes.
Temperature field is also obtained at two different heights to show how temperature changes
from the engines to the far fields in Figure 7. Since the biggest heat sources are the main
engines the highest temperatures have been calculated near the engines. The circulation of
the fresh air that comes from the atmosphere cools down the air temperature in all directions.
Figure 8. Comparison of the measured and calculated temperature in engine room (in C).
The circulation of the fresh air within the engine room is illustrated in Figure 9. As stated
before, there are two inlets for supplying the fresh air for the main engines, generators set
and crew in the engine room. Once it comes in to the engine room it has been directed towards
the main engines especially to the inlets of the main engines. Due to limited spaces occupied
with various bodies such as engines, pipes and others the fresh air accelerates and decelerates
during its motion in the engine room. The motion of the fresh air is similarly observed during
the sea trials.
Figure 9. Motion of the fresh air comes from the inlets (colored with velocity in m/s).
Due to the limited spaces and the sharp corner of the engines and ducts lots of recirculation
regions are observed as presented in in Figure 10. Recirculation regions with bigger in size
are observed at the region between the main engines and top roof of the engine room. In
addition to these, relatively small but strong recirculation regions are seen in front and rear
of the engines. The existence of the sharp edges of the working domain leads to form smaller
circulation regions around the engines.
(a) (b)
Figure 10. Recirculation regions in the engine room and (a) u-velocity distribution
superimposed streamlines (b) .
4. Conclusion
This study reports the flow of fluid and heat in an engine room of a tugboat in service.
Temperatures at a specific locations are measured during the sea-trials of the boat and then
compared with the numerically calculated data. It is seen that both data are in good agreement
Temperature distributions on the engines and in the engine room are provided at various
planes.
4. Acknowledgements
The authors acknowledge the support of SANMAR Shipyards for providing the precious
information about their tugboat.
4. References
[11] Newton, W., Lewis, M., Carswell, D., Lavery, N., Evans, B., Bould, D., Sienz, J.,
Investigating the thermal profile of a marine vessel engine room through simulation
with field measurements, Applied Thermal Engineering, 73, 1360-1370, 2014.
[12] Li, X.J., Zhou, R.P., Konovessis, D., CFD analysis of natural gas dispersion in engine
room space based on multi-facto coupling, Ocean Engineering, 111, 524-532, 2016.