Offshore Survey Division

Starfix-StarPack

Image : Width 188mm

StarPack is Fugro’s answer to increasing market demand for precise, redundant GNSS positioning solutions,
including extensive QC and accurate timing, from a single, easy to use platform.

StarPack Unit
A StarPack unit consists of a survey grade GNSS receiver and
powerful processor, running Linux multi-tasking operating
system. The receiver is capable of tracking all current (GPS,
GLONASS)and future (Galileo) systems.A StarPack can be
extended with a second receiver (in the same unit) to provide
accurate,GNSS derived heading.

The combination of receiver and processor provides for robust

multiple simultaneous precise position calculations and
extensive QC. For maximum system reliability the internal StarPack Unit
software is embedded on flash memory configured on the
processor. Control and configuration of the system is via the
front panel, a web interface or a serial port.

Four serial ports and LAN interface to read multiple correction

sources (in addition to the integrated receiver) and to provide
multiple outputs to the user are available on
the system rear panel.
Image : Width 78mm
this column must always be
Documentation
used forimages only
This section describes the various user, installation and
technical references for the equipment. The Starpack User
Manual contains the specifications and user details.

Input Data Formats StarPack Web Interface

Data inputs to the Starpack from a PC are considered advanced

CODEC features, and are not supported at this time. Image : Width 78mm
The StarPack can handle two formats: RTCM or “Fugro”. Fugro this column must always be
format is the format from the Starfix network, also called used for images only
SuperCompressed in Starfix.IOWIN.

Output Data Formats

This section describes the various data formats the equipment

OUTPUTS to other equipment. These outputs are typically
interfaced to Starfix.NG which decodes and consumes the data.
StarPack-QC running in real-time
Starfix-StarPack

Technical Specifications
Type Accuracy
Starfix.XHP Position 0.1m 2DRMS
Starfix.G2 Position 0.1m 2DRMS
Starfix.Plus Position 0.08m 2DRMS
GNSS Position 2.0m 2DRMS
Velocity 0.05m/s RMS
NMEA messages
$GPGGA Fugro Proprietary HP Monitor formats
$GPGSA $PFGRPVT
$GPVTG $PFGRHPQ
$PASHR

Information may be subject to change without prior notice

Fugro OCEANSISMICA S.p.A.

Viale Charles Lenormant, 268
00126 Rome
Italy
Telephone: +39 06 5219291
Email: [email protected]

More information available at WWW.FUGRO.COM © Fugro 2012

 Offshore Survey Division
OmniSTAR 9200-G2 Receiver

Image : Width 188mm

The OmniSTAR’s G2 is a composite GLONASS/GPS positioning solution available worldwide. By utilizing satellites
from both costellations G2 can provide consistent and stable decimetre accuracy.

All in View Receiver

The OmniSTAR 9200-G2 GNSS receiver is a multi frequency
(L1I L2IL51E1IE5) receiver that incorporates GPS and
GLONASS capability. In addition, it tracks the Fugro L-Band 78mm
satellite broadcast of DGNSS corrections. As a backup it
can receive the DGNSS corrections via Internet.
As well as providing increased accuracy, multi frequency
operation means that the OmniSTAR 9200-G2 DGNSS
receiver is well equipped to cope with the effect of the
OmniSTAR 9200-G2
forecast increase in solar activity and interference.
Used in conjunction with the Marinestar® GNSS service, it
increases the number of satellites available by accessing
the GLONASS satellite constellation in addition to the GPS
constellation.

High Performance Service Compatibility

The OmniSTAR 9200-G2 DGNSS receiver can be subscribed to

the various DGNSS services offered by Fugro such as
Marinestar® GPS and the integrated Marinestar GNSS service.:
OmniSTAR 9200-G2 back panel

• Marinesta® GPS: GPS orbit and clock solution

• Marinesta® GNSS: Composite GPS/GLONASS orbit and
clock solution

The above solutions are dual frequency carrier phase based to

achieve decimeter level accuracy.
The receiver can be monitored and configured via the front
panel display and keypad, or via a web interface.
.
Image : Width 78mm
this column must always be
used for images only

A mix of navigation satellites can be used

OmniSTAR 9200-G2 Receiver

Technical Specifications
Main Features Power Requirements
L1/L2 GPS receiver Corrections via internet 9.5VDC to 28VDC 30W at 24VDC
L1/L2 GLONASS receiver Display and keypad AC input via external ACIDC PSU
L-BAND DGNSS receiver Web interface or Isolating Data and Power Unit
(IDPU)

Channels Temperature
220-channels SBAS (WMS/EGNOS/MSAS) Operating : -40 to +65°C (-40 to +149°F)
GPS – L1 C/A, LI2C code Fugro L-Band service Storage: -40 to +80°C (-40 to +176°F)
GPS - L1/L2/L2C full cycle carrier
GLONASS-L1/IL2full cycle carrier

Position Accuracy Marinestar GPS/GNSS Dimensions (L x W x OJ)

Horizontal 10 cm. 95% 24 CM (9.4 in) x 12 cm (4.7 in) x 5 cm (1.9 in)
Vertical 15 cm. 95%

Communications Weight
Lemo (serial) 3 wire RS232 1.55 Kg (3.42 lb)
Modem 1 serial Full 9-wire RS232
Modem 2 serial Full 3-wire RS232
1 PPS

Data Outputs Approval

NMEA messages: GGA; GST; GSA; VTG; IEC 61108 GNSS performance
180L x 186W IEC 60945 GNSS environmental (IPDU required)
ZDA; GNS; GBS;xRMC
75H
IEC 61162 interface output

Information may be subject to change without prior notice

Fugro OCEANSISMICA S.p.A.

Viale Charles Lenormant, 268
00126 Rome
Italy
Telephone: +39 06 5219291
Email: [email protected]

More information available at WWW.FUGRO.COM © Fugro 2012

 Octans 3000
High-performance subsea gyrocompass
and motion sensor
OCTANS 3000 is a subsea survey-grade gyrocompass and complete motion sensor for water depths up to 3 000 m.
Based on iXBlue’s FOG technology it outputs heading, roll, pitch, heave, rate of turn and acceleration. OCTANS 3000 can
be easily upgraded to full INS mode (i.e. ROVINS).

FEATURES BENEFITS

• Complete gyrocompass and motion sensor • High-performance real-time outputs of true heading, roll,
pitch, heave, surge, sway, acceleration and rate of turn
• Smart Heave TM

• No spinning element hence maintenance free

• Fiber-optic gyroscope (FOG), unique strap-down
technology • Lightweight corrosion free housing for water depth up to 3 000 m,
easy to integrate and interface, saves valuable mobilization time
• Ethernet, web-based man-machine interface (MMI)
• Obtain INS-class system with simple software upgrade
• Titanium made, small, portable plug and play system
• Optional full featured inertial navigation system

APPLICATIONS • ROV and offshore survey • MBES and sonar motion reference • Dredging • Marine construction

Courtesy of Van oord Courtesy of Ifremer Courtesy of Stolt Offshore

OCTANS 3000
technical specifications

performance
Heading
Accuracy (1)(2) 0.1 deg secant latitude
Resolution 0.01 deg
Full accuracy settling time (all conditions) < 5 min
Heave accuracy (3) 2.5 cm or 2.5% (whichever is greater)
Roll / Pitch
Dynamic accuracy (2) 0.01 deg
Resolution 0.001 deg
operating range / environment
Operating / storage Temperature -20 °C to +55 °C / -40 °C to +80 °C
Follow-up speed Up to 750 deg/s
Acceleration dynamic range ±15 g
Heading / roll / pitch 0 to +360 deg / ±180 deg / ±90 deg
MTBF (computed/observed) 40 000 hours / 80 000 hours
No warm-up effects, insensitive to thermal shocks
Shock and vibration proof

physical characteristics
Depth Material Weight Housing Connector Mounting
rating (m) (air / water) kg dimensions (Ø x H mm)

3 000 Titanium 15 / 6.2 213 x 375 5 x SEACON MI-CON 6 Ø 6.6 holes

interfaces
Serial RS232 / RS422 port 5 inputs / 5 outputs / 1 configuration port
Ethernet port (5) UDP / TCP client / TCP server
Pulse port (6) 3 inputs / 2 outputs
Sensors supported GPS, speed log
Input / output formats Industry standards: NMEA0183, ASCII, BINARY
Baud rates 600 bauds to 115.2 kbaud
Data output rate 0.1 Hz to 200 Hz
Power supply 24 VDC
Power consumption < 20 W

2014-02-PS-OCT3000
(1) secant latitude = 1 / cosine latitude
(2) RMS values
(3) Smart HeaveTM
(4) All input /output serial ports are available and can be duplicated on Ethernet ports
(5) Input of GPS PPS pulse for accurate time synchronization of OCTANS 3000
(6) Maximum error = 3 or RMS error

www.ixblue.com • EMEA: +33 1 30 08 88 88 • AMERICAS: +1 888 600 7573 • APAC: +65 6747 4912

Specifications subject to change without notice.

 Hydrins
fog-based high-grade inertial navigation system
for hydrographic and multibeam surveys
HYDRINS is a high-performance inertial navigation system optimized for hydrographic surveys using multibeam
echosounders. HYDRINS comprises a single compact unit and delivers highly accurate real-time position, heading,
attitude and speed data. In addition to the real-time options, HYDRINS raw data can be post-processed using Delph INSTM.

FEATURES BENEFITS
• All-in-one high-accuracy 3D positioning with heading, roll and pitch • Motion and heading not affected by GPS outages
• Smart Heave TM
• Accurate height compensation with GPS RTK
• Automatic GPS drop-out / multipath management • A complete solution with easy-to-use yet powerful
• Advanced post-processing software solutions (Delph INS) post-processing tools
• Fast and reliable installation on all vessels
• Compact, uses any kind of GPS (single antenna)
• Network ready, intuitive user interface
• Ethernet, web server (GUI)

APPLICATIONS • Multibeam survey • Hydrographic survey • Harbors and inland waterways

Courtesy of Geoplus
HYDRINS
technical specifications
IMO Certified
N° 19110
performance N° 19183

Position accuracy real time

With GPS Three times better than GPS
No aiding for 1 min / 2 min 0.8 m / 3.2 m (CEP 50)
Position accuracy post-processed
With GPS Four times better than GPS
No aiding for 1 min / 2 min 0.2 m / 1m (CEP 50)
Heading accuracy 0.01 deg secant latitude RMS(1)
Roll and pitch dynamic accuracy (no aiding) 0.01 deg RMS
Heave accuracy (Smart Heave)(2) 2.5 cm or 2.5% RMS

operating range / environment

Operating / storage temperature -20°C to 55°C / -40°C to 80°C
Rotation rate dynamic range Up to 750 deg/s
Acceleration dynamic range ± 15 g
Heading / roll / pitch 0 to +360 deg / ±180 deg / ±90 deg
MTBF (observed) 80 000 hours

physical characteristics
Dimensions (L x W x H) 180 x 180 x 162 mm
Weight 4.5 kg
Waterproof IP66

interfaces
Serial RS422 or RS232
Ethernet 100 MBit - UDP / TCP server / TCP client / WebGUI
Pulse PPS, Trigger
Inputs / outputs Configurable 7i / 5o - Pulse(3) 4i / 2o - Configuration port
Baud rates Up to 460 kbaud
Data output rate 0.1 Hz to 200 Hz
Power supply / consumption 24 VDC (20 - 32 V) / < 20 W

(1) Secant latitude = 1/cosine latitude

(2) Whichever is greater for periods up to 30 seconds. Smart heave is delayed by 100 s fixed value

2014-02-PS-HYD
Real-time heave accuracy is 5 cm or 5% whichever is greater
(3) Use GPS PPS pulse for accurate time synchronization of HYDRINS

www.ixblue.com • EMEA: +33 1 30 08 88 88 • AMERICAS: +1 781 937 8800 • APAC: +65 6747 4912

Specifications subject to change without notice.

 EA 400/600 Sidescan

Echo sounder with combined sidescan

and depth soundings
855-164731 / Rev. C / November 2005
 EA 400/600 Sidescan option

Side-looking image

The side-looking option is available for the EA 400,

EA 400P and EA 600 hydrographic echo sounders.
Using a sidescan sonar transducer, these echo sound-
ers can produce a side-looking image on the side of
the vessel the transducer is located. By employing two
transducers (to port and starboard) both sides may be
surveyed at the same time.

Mounted, not towed

An other very handy solution is to use hull mounted

or over-the-side boom mounted sidescan transducer(s)
to survey shallow areas such as harbors, rivers and
canals. This eliminates the need for a towed sidescan Sidescan with only starbord TD mounted.
sonar or similar device. Another advantage is that fixing
the correct geographic location of detected objects is Combining dual sidescan with
made much simpler and done more precisely since the normal depth sounding
uncertainty concerning the position of a towed body
has been eliminated. It is also possible to allocate one or two vertical
channels to normal echo sounding in addition to dual
Side-looking option acoustic imaging. EA400SP is limited to run either dual
sidescan or single sidescan with one vertical channel.
The sidelooking option is equally useful when
searching for wrecks or surveying navigable channels Easy to operate
for obstacles. Sidescan data is captured and stored in a
digital format and further data processing to a sidescan The presentation of dual sidescan image can easily
sonar mosaic image (by combining data from a number be changed in the operator menu. The normal echo
of survey lines) is possible and easy to perform. sounding view(s) can be turned on or off in the menu.
Georef output datagram can be exported through The bottom line for third or the fourth channels, can be
network if vertical channel is available. overlaid on the sidescan presentation (one or both) as
a red line.

The sidescan transducers

With a working frequency of 120 or 200 kHz,

Kongsberg Maritime has combined both high accuracy
and resolution with robustness and wide coverage.
The 120-2x50 is a sidescan transducer with a narrow
longitudinal beamwith of 1.9 degrees, and a wide
transverse beam of 55.0 degrees. The 200kHz trans-
ducer has a longitudinal beamwith of 0.5degrees and a
transverse beam of 49.0 degrees. Both transducers has
a scanning sector narrow enough to reveal the secrets
of the seafloor, including small objects and wrecks in
great detail, but wide enough to allow faster survey
speeds than possible with conventional side-looking
Dual sidescan with bottom depth channel. units.
 Hull mounting
(CD6707A)

Athwartship view from stern, not to scale.

Outer hull Outer hull

Port blister Starboard blister

Echo sounder

Sidescan transducer Sidescan transducer

o o
50 50

o
7

Typical hull mounting arrangement

Over-the-side mounting

Vertically mounted Horizontally mounted

(CD6817D)

(CD6817C)

o
50

o
50

Typical vertical installation Typical horizontal installation (down to 50 m)

 Technical specifications

120-2x50 Sidescan transducer Transversal beamwith ............................ 55.0 degrees

The 120-2-50 transducer has a narrow longitudinal Maximum pulse power input .........................1000 W
and a wide transverse beam. Maximum continous power input ......................10 W
Measuring slant range (approx.) ............... 0 to 300 m Maximum transducer depth ............................... 20 m
Survey speed (max)....................................6 - 8 knots Cable length ....................................................... 20 m
Resonant frequency.......................................120 kHz Weight with cable .............................................5.5 kg
Longitudinal beamwidth .......................... 1.9 degrees Storage temperature ............................... +70 to -40 C

200-0.5x49 Sidescan transducer Transversal beamwith ............................ 49.0 degrees

The 200-0.5x49 transducer has a narrow longitudinal Maximum pulse power input .........................1000 W
and a wide transverse beam. Maximum continous power input ......................27 W
Measuring slant range (approx.) ............... 0 to 200 m Maximum transducer depth ............................... 10 m
Survey speed (max)....................................6 - 8 knots Cable length ....................................................... 20 m
Resonant frequency.......................................200 kHz Weight with cable ................................................8 kg
Longitudinal beamwidth .......................... 0.5 degrees Storage temperature ................................. +48 to -6 C

Note: The proceeding photographs are not representative of the relative size of the two transducers.

Due to the continuous development of its products, Kongsberg Maritime reserves the right to alter the specifications
show above without notice. Please contact a sales representative for further information.

Kongsberg Maritime AS
Strandpromenaden 50 Telephone: +47 33 02 38 00
P.O.Box 111 Telefax: +47 33 04 47 53
N-3191 Horten, www.kongsberg.com
Norway E-mail: [email protected]
EM 2040

Multibeam echo sounder

True wide band high resolution

multibeam echo sounder
 EM 2040

Key facts
The EM 2040 multibeam echo
sounder is the first system to bring
all the advanced features of deep
water multibeams to the near bottom
sounding environment. Important
deep water system features included
with the EM 2040 are:
• Dual swath per ping to allow a
doubling of survey speed
• FM chirp to achieve a much longer
range capability
• Complete roll, pitch and yaw
stabilization
• Nearfield focusing both on
transmit and receive
The EM 2040 is modular, allowing
the user to tailor the beamwidths to
the operational requirements, 0.4
by 0.7 and 0.7 by 0.7 degrees. The
transmit fan is divided into three
sectors pinging simultaneously at
separate frequencies. This ensures a
very strong and beneficial dampening
of multibounce interference which
on simpler systems often is seen at
beam angles from 60 degrees and
outwards. The EM 2040 has dual EM 2040 subsea parts is 6000 m. The column between the transducers
swath capability, allowing a sufficient system is ideal for operation on subsea and the bottom. Sound speed at the
sounding density alongtrack at a vehicles such as ROVs or AUVs. All transducer is an optional input.
reasonable vessel speed. analog electronics are contained in the The EM 2040 is delivered with a
The operating bandwidth available transducers, and communication to the mounting plate with factory aligned
on the EM 2040 is unprecedented, topside Processing Unit is on standard guidances. It is recommended that
from 200 to 400 kHz, which is a Ethernet. For more information the mounting plate is built into a steel
full octave, and this is achieved about the use of EM 2040 on ROVs casing and protected by a baffle for
with the standard transducers. The and AUVs please see the following multipath reduction. Optionally, the
operator can thus on the fly choose application notes (document numbers transducers may be delivered mounted
the best operating frequency for in brackets): on a frame together with the motion
the application, 300 kHz for near • High Resolution Bathymetry sensor and a sound speed sensor,
bottom, 200 kHz for deeper waters, from ROV Mounted EM 2040 factory aligned for ease of mounting.
and 400 kHz for very high resolution [368428] The EM 2040 is a modular system,
inspection. • High Resolution Bathymetry fully prepared for upgrading to cater
The bandwidth of the EM 2040 from ROV Mounted EM 2040 and for more demanding applications. The
transducers allows the system to HAIN Navigation [368429] transmit transducer has an angular
effectively operate with very short coverage of 200º (±100º) as standard,
pulse lengths, i.e. down to 25 Components allowing a coverage of 5.5 times
microseconds. With 25 microseconds The basic EM 2040 has four water depth when matched with a
pulse length the raw range resolution units, a transmit transducer, a receive single receive transducer. Adding
(cτ/2) is 18 mm. transducer, a processing unit, and a a second receive transducer allows
The EM 2040 is well suited for workstation. For completeness, data surveying to the water surface or up to
surveys meeting the IHO-S44 special input from a motion sensor and a 10 times water depth on flat bottoms.
order. positioning system is required, as is The transducers are separate units
The standard depth rating of the the sound speed profile of the water with titanium housings.
 EM 2040

The transducers are interfaced to such as water column sediments. 600 m and a depth capability of about
a processing unit via Ethernet, 100 200 kHz is available for meeting 400 m in cold ocean waters.
Megabit/s to the transmit transducer requirements to operate at the The 200 kHz frequency mode
and Gigabit from the receive standard hydrographic single beam has the same CW pulselengths as
transducer. The Processing Unit also frequency, but also to achieve the best the 300 kHz mode. The FM chirp
supplies power to the transducers. depth capability. 400 kHz is provided pulselength is extended compared
Operator control, data quality for inspection work with the utmost to the 300 kHz mode. Normally two
inspection and data storage is handled resolution. sectors are used per swath. At this
by the hydrographic workstation The normally recommended frequency the absorption in the water
running the same SIS software as all survey frequency is 300 kHz. At this is lower than at 300 kHz, resulting
other Kongsberg multibeams. frequency the bandwidth used is more in increased swath width and depth
than 75 kHz with three angular sectors capability. In cold ocean waters with
Operational modes which are run at separate frequencies. FM chirp a swath width of 700 m can
The EM 2040 has a frequency With dual swath six separate be expected, and approximately 500
range of 200-400 kHz. Three frequencies are used. The minimum m depth capability achieved.
standard modes are available. 300 pulselength is 35 microseconds. The The 400 kHz frequency mode is
kHz is used for normal operation, range resolution is then 26 mm. For intended for high resolution inspection
giving an optimum balance between deep waters FM chirp is employed work. Very short transmit pulses and
high resolution, depth capability with a bandwidth of 1.7 kHz. This wide receiver bandwidth is used. The
and tolerance of detrimental factors allows a swath width in the order of operator may choose between one and
three transmit sectors. With a single
Advanced functions RX transducer the coverage can be
up to 120º (±60º), and with dual RX
• Frequency range: 200 to 400 kHz the coverage can be up to 180º (±90º).
The shortest pulse used is 25 µs. It is
• Dual swath capability, allowing a sufficient sounding density alongtrack also possible to run dual swath, but
at a reasonable survey speed not with the shortest pulse length.

• FM chirp allowing much longer range capability

• Complete roll, pitch and yaw stabilization

• Nearfield focusing on both transmit and receive

• Operates with very short pulse lengths, down to 25 microseconds

• The depth rating of the subsea parts is 6000 m

Transducer array (Rx/Tx)

Monitor HydrographicWork Station (HWS) Processing Unit (PU)

 Technical specifications

• Frequency range: 200 to 400 kHz • Sounding patterns: • Roll stabilized beams: Yes, +/-15°
• Max ping rate: 50 Hz Equiangular, Equidistant and High • Pitch stabilized beams: Yes, +/-10°
• Swath coverage sector: Up to 140º Density • Yaw stabilized beams: Yes, +/-10°
(±70º) (single RX) / 200 º (±100º)
(dual RX)

EM 2040-04 Cold ocean Cold fresh water

Operating frequency Max depth Max coverage Max depth Max coverage
200 kHz 635 m 890 m 1360 m 1900 m
300 kHz 480 m 740 m 740 m 1120 m
400 kHz 315 m 430 m 430 m 540 m

EM 2040-07 Cold ocean Cold fresh water

Operating frequency Max depth Max coverage Max depth Max coverage
200 kHz 600 m 850 m 1300 m 1780 m
300 kHz 465 m 705 m 700 m 1060 m
400 kHz 300 m 410 m 375 m 510 m

Pulse lengths 200 kHz 300 kHz 400 kHz

CW FM CW FM CW FM
Normal mode 70, 200 and 600 µs 3/12 ms 70, 200 and 600 µs 2/6 ms 50, 100 and 200 µs N/A
Single sector mode 35, 70 and 150 µs 1.5 ms 35, 70 and 150 µs 1.5 ms 25, 50 and 100 µs N/A

Max no. of soundings per ping (dual swath) 200 kHz 300 kHz 400 kHz
Single RX 800 800 800
Dual RX 1600 1600 1600

Max no. of soundings per ping (single swath) 200 kHz 300 kHz 400 kHz
Single RX 400 400 400
Dual RX 800 800 800

Physical dimensions (excluding connectors and mounting arrangements)

200 kHz 300 kHz 400 kHz Dimensions Weight
Tx EM 2040-04 0.7° 0.5° 0.4° 727 x 150 x 142 mm (L x H x W) 45 kg
Tx EM 2040-07 1.5° 1° 0.7° 407 x 150 x 142 mm (L x H x W) 24 kg
Rx 1.5° 1° 0.7° 407 x 136 x 142 mm (L x H x W) 23 kg
Processing Unit (4U 19” rack)* 447 x 178 x 345 mm (W x H x D) 15 kg
Hydrographic Work Station (4U 19” rack) 427 x 178 x 480 mm (W x H x D) 20 kg
19” Monitor 483 x 444 x 68 mm (W x H x D) 12 kg

* More than one Processing Unit may be necessary

Kongsberg Maritime is engaged in continuous development of its products, and reserves the right to alter the
specifications without further notice.

332644 / Rev.I / October 2012

Kongsberg Maritime AS
Strandpromenaden 50 Telephone: +47 33 02 38 00
P.O.Box 111 Telefax: +47 33 04 47 53
N-3191 Horten, www.kongsberg.com
Norway [email protected]
4200 SERIES
SIDE SCAN SONAR SYSTEM

FEATURES
• Optional Multi-Pulse (MP) technology
for high speed surveys
• Crisp, high resolution CHIRP images
• Multiple dual simultaneous frequency
sets to choose from
• Stainless steel towfish
• Easily integrates to other 3rd party
sensors
• Meets IHO & NOAA Survey
Specifications

APPLICATIONS The 4200 Series is a versatile side scan sonar system that can be configured
for almost any survey application from shallow to deep water operations. The
• Cable & Pipeline Surveys
4200 utilizes EdgeTech’s Full Spectrum® CHIRP technology to provide crisp,
• Geological/Geophysical Surveys
high resolution imagery at ranges up to 50% greater than non-CHIRP systems;
• Mine Countermeasures (MCM) thus allowing customers to cover larger areas and save money spent on costly
• Geohazard Surveys surveys.

• Channel Clearance One of the unique features of the 4200 is the optional Multi-Pulse (MP)
• Search and Recovery technology, which places two sound pulses in the water rather than one pulse
• Archeological Surveys like conventional side scan sonar systems. This allows the 4200 to be towed
at speeds of up to 10 knots while still maintaining 100% bottom coverage. In
addition, the MP technology will provide twice the resolution when operating at
normal tow speeds, thus allowing for better target detection and classification
ability. The addition of the optional MP technology provides the operator with
two modes of operation; either High Definition Mode (HDM) or High Speed
Mode (HSM). This software-selectable mode of operation provides the operator
the ability to select the best configuration for the specific job type.

All EdgeTech 4200 systems are comprised of a topside system and a reliable stainless
steel towfish. A choice of dual simultaneous frequency sets are available to the user
and topside processors come in a choice of configurations from portable to rack
mounted units. In addition, an easy-to-use GUI software is supplied with every unit.

For more information please visit EdgeTech.com

[email protected] | USA 1.508.291.0057
 4200 SERIES
SIDE SCAN SONAR SYSTEM

KEY SPECIFICATIONS

Sonar Specifications Standard With Optional MP TECHNOLOGY

Frequency Choice of either 100/400, 300/600 or 300/900 kHz dual simultaneous
Operating Range (meters/side) 100 kHz: 500m, 300 kHz: 230m, 400 kHz: 150m, 600 kHz: 120m, 900 kHz: 75m
Horizontal Beam Width: 100 kHz: 1.5°, 300 kHz: 0.5°, 400 kHz: 0.4°, In High Speed Mode: 100 kHz: 1.26°,
600 kHz: 0.26°, 900 kHz: 0.2° 300 kHz: 0.54°, 400 kHz: 0.4°, 600 kHz: 0.34°,
900 kHz: 0.3°

In High Definition Mode: 100 kHz: 0.64°,

300 kHz: 0.28°, 400 kHz: 0.3°, 600 kHz: 0.26°,
900 kHz: 0.2°
Resolution Along Track 100 kHz: 5 m @ 200 m High Definition Mode: HIgh Speed Mode:
300 kHz: 1.3 m @ 150 m
400 kHz: 0.6 m @ 100 m 100 kHz: 2.5m @ 200m 100 kHz: 4.4m @ 200m
600 kHz: 0.45 m @ 100 m 300 kHz: 1.0m @ 200m 300 kHz: 1.9m @ 200m
900 kHz: 18 cm @ 50 m 400 kHz: 0.5m @ 100m 400 kHz: 0.7m @ 100m
600 kHz: 0.45m @ 100m 600 kHz: 0.6m @ 100m
900 kHz: 18 cm @ 50m 900 kHz: 26 cm @ 50m
Resolution Across Track 100 kHz: 8 cm, 300 kHz: 3 cm, 400 kHz: 2 cm, 600 kHz: 1.5 cm, 900 kHz: 1 cm
Vertical Beam Width 50°
Depression Angle Tilted down 20°
Towfish Stainless Steel
Diameter 11.4 cm (4.5 inches)
Length 125.6 cm (49.5 inches)
Weight in Air/Saltwater 48 / 36 kg (105 / 80 pounds)
Depth Rating (Max) 2,000m
Standard Sensors Heading, pitch & roll
Optional Sensor Port (1) Serial – RS 232C, 9600 Baud, Bi-directional & 27 VDC
Options Pressure Sensor, Magnetometer, Integrated USBL Acoustic Tracking System, Built-in Responder Nose,
Depressor, Power Loss Pinger and Custom Sensors
Topside Processor 4200-P 4200 701-DL Interface
Hardware Portable splash-proof case 19” rack mount computer 19” rack mount interface
Display & Interface Splash-proof laptop 21” flat panel monitor, Customer-supplied
keyboard & trackball
Power Input 20-36 VDC or 115/230 VAC 115/230 VAC 115/230 VAC
Operating System Windows© XP Pro
File Format Native JSF or XTF
Output Ethernet
Tow Cable
Coaxial Kevlar or double-armored up to 6,000m, winches available

For more information please visit EdgeTech.com

[email protected] | USA 1.508.291.0057
 Š
+L3$3 
+LJK3UHFLVLRQ$FRXVWLF3RVLWLRQLQJ6\VWHP

:25/'&/$66WKURXJKSHRSOHWHFKQRORJ\DQGGHGLFDWLRQ
 6\VWHPIHDWXUHV

,QWURGXFWLRQ %HDPVWHHULQJLVWKHPDMRUNH\IRUVXFFHVVIXODFRXVWLF
7KH +L3$3  LV DQ XQGHUZDWHU SRVLWLRQLQJ V\VWHP SHUIRUPDQFHWKURXJKPD[LPXPUDQJHDQGDFFXUDF\
XVLQJWKH6XSHU6KRUW%DVH/LQH66%/SULQFLSOH7KH
PDLQDGYDQWDJHRIWKLVSULQFLSOHLVWKDWLWRQO\UHTXLUHV /RQJ%DVH/LQHIXQFWLRQDOLW\
LQVWDOODWLRQ RI RQH KXOOPRXQWHG WUDQVGXFHU DQG RQH $WVRPHSRLQWRIUDQJHGHSHQGLQJRQWKHDSSOLFDWLRQ
VXEVHDWUDQVSRQGHU WKH66%/SULQFLSOHZLOOKDYHDFFXUDF\OLPLWDWLRQ/%/
7KHV\VWHPGHVLJQZDVEDVHGRQDPDUNHWUHTXLUHPHQW DFFXUDF\LVLQGHSHQGHQWRIUDQJH$Q/%/V\VWHPFDQ
RI DYRLGLQJ WKH /RQJ %DVH /LQH /%/ SULQFLSOH LQ SRVLWLRQPRUHDFFXUDWHO\EXWRQO\ZLWKLQDQDUUD\RI
GHHS ZDWHU DFFXUDWH VHDEHG VXUYH\ DSSOLFDWLRQV 7KH VHDEHG WUDQVSRQGHUV 7KH +L3$3 ZLWK RSWLRQDO /%/
XQLTXH WUDQVGXFHU WHFKQRORJ\ DQG DGYDQFHG VLJQDO IHDWXUHV LPSOHPHQWHG LV D YHU\ ÀH[LEOH V\VWHP FRP
SURFHVVLQJ XVHG LQ +L3$3  ZDV IRXQG WR EH WKH ELQLQJWKHDGYDQWDJHVRIERWK66%/DQG/%/
VROXWLRQ IRU REWDLQLQJ WKH RSWLPDO SRVLWLRQ DFFXUDF\ 7KH +L3$3 KDV EHWWHU ORQJ UDQJH SHUIRUPDQFH WKDQ
UHTXLUHGLQWKHVHGHHSHUZDWHUV WUDGLWLRQDO ZLGH EHDP V\VWHPV 7KLV LV EHFDXVH WKH
([WUHPHDFFXUDF\DTXDQWXPOHDS 6LJQDOWR1RLVH UDWLR RI WKH GHWHFWHG VHDEHG WUDQV
7KH +L3$3  HVWDEOLVKHV VXEVHD SRVLWLRQLQJ VR SRQGHUV¶UHSOLHVDUHKLJKHUWKDQZKHQXVLQJRQHZLGH
DFFXUDWH WKDW WKH PRUH FRPSOH[ EXW FRPPRQ /%/ EHDP WKDW QHHGV WR FRYHU WKH VHDEHG IRRWSULQW RI D
SULQFLSOH ZDV PDGH UHGXQGDQW ZLWKLQ UHDVRQDEOH WUDQVSRQGHUDUUD\
GHSWKV7LPHDQGFRVWRIVXUYH\RSHUDWLRQVZDVWKHUH
IRUHUHGXFHGWRDPLQLPXP
7KH+L3$3V\VWHPSURYHVWRKDYHVXFFHHGHGWKH
TXDQWXP OHDS LQ WHFKQRORJ\ ZLWK KXQGUHGV RI HOH
PHQWV LQ WKH VSKHULFDO WUDQVGXFHU$OO WKHVH HOHPHQWV
DOVRVHFXUHDQH[WUHPHO\KLJKLQWHUQDOUHGXQGDQF\DQG
UHOLDELOLW\ 7KH DGYDQFHG WUDQVGXFHU WHFKQRORJ\ DQG
DFRXVWLF VLJQDO SURFHVVLQJ PDNHV WKH +L3$3  WKH
PRVWDFFXUDWH66%/V\VWHPLQWKHZRUOG

0XOWLYHVVHOSRVLWLRQLQJ
7KH 0XOWL8VHU /%/ 08/%/ IXQFWLRQ HQDEOHV
VHYHUDO LQGLYLGXDO YHVVHOV DQG 529 XQLWV WR SRVLWLRQ
WKHPVHOYHVXVLQJWKHVDPHVHDEHGWUDQVSRQGHUDUUD\

/%/IRUVXEVHDFRQVWUXFWLRQ
.RQJVEHUJ 6LPUDG LQWURGXFHG WKH /%/ V\VWHP LQ
DQGKDVVLQFHWKHQEHFRPHWKHPDUNHWOHDGHUIRU
VXSSO\RI/%/DQGFRPELQHG/%/66%/V\VWHPVIRU
YHVVHOSRVLWLRQLQJ
6XSSUHVVLRQ RI QRLVH XVLQJ EHDP 7KH FXUUHQW /%/ V\VWHPV XVH LQWHOOLJHQW LQVWUX
SRLQWLQJFRQWURO PHQWHG WUDQVSRQGHUV WUDQVFHLYHUV DQG WUDQVGXFHUV
7KH V\VWHP G\QDPLFDOO\ FRQWUROV D GHJUHH FRQH 7KHVHDUHDOOUDWHGIRUPZDWHUGHSWKDQGIXO¿O
DFRXVWLFOLVWHQLQJEHDP7KLVFRQHSRLQWVWRZDUGVWKH DQ\ UHTXLUHPHQWV ZLWKLQ VXEVHD FRQVWUXFWLRQ VXUYH\
WUDQVSRQGHUV ZKHUHYHU WKH\ DUH ORFDWHG EHORZ WKH DQGPHWURORJ\
YHVVHO
³:RUOG5HFRUG´
7KH +L3$3 V\VWHP LV VR IDU WKH RQO\ V\VWHP WKDW
LQWUDQVSRQGHUFKDQQHOV
FDQ FRQWURO D IRFXVHG OLVWHQLQJ EHDP WRZDUGV WKH
7KH +L3$3 V\VWHPV FDQ RSHUDWH ZLWK PD[LPXP 
WUDQVSRQGHUV7KLVPHDQVWKDWQRLVHIURPRWKHUGLUHF
WUDQVSRQGHU FKDQQHOV DQG KDV WUDQVSRQGHU WHOHPHWU\
WLRQV LV VXSSUHVVHG7KLV SURYLGHV D JRRG IRXQGDWLRQ
FRPPXQLFDWLRQIRUXVHZLWKWUDQVSRQGHUUHOHDVH
IRUIXUWKHUVLJQDOSURFHVVLQJ
VHQVRUUHDGLQJVDQG/%/DXWRFDOLEUDWLRQ
$XWRPDWLFFRPSHQVDWLRQIRUUD\EHQG
LQJDQGVRXQGYHORFLW\HUURUV
7KH+L3$3FDQWDNHLQSXWRIWKHVRXQGYHORFLW\SUR¿OH
LQWKHZDWHUFROXPQ%DVHGRQWKLVSUR¿OHWKHV\VWHP
ZLOODXWRPDWLFDOO\FRPSHQVDWHIRUWKHHUURUFRQWULEX /PERATOR
WLRQIURPERWKZURQJDQJOHDQGUDQJHGHWHFWLRQ 3TATION

$ATA
OUTPUT

4RANSCEIVER
5NIT

(OIST#ONTROL
2OLL
PITCHAND
5NIT
HEADING

(ULL
<RX FDQ DOVR VHH WKH UD\WUDFH RQ WKH GLVSOD\ ZKLFK 5NIT
ZLOORIWHQH[SODLQWKHUHDVRQIRU³QRUHSO\´SUREOHPV

3UHIHUUHGV\VWHPDOVRIRUG\QDPLF
SRVLWLRQLQJUHIHUHQFH
:LWK LWV KLJK DFFXUDF\ JRRG UHSHDWDELOLW\ DQG KLJK
UHOLDELOLW\+L3$3LVWKHPXOWLSXUSRVHV\VWHPIRU
DQ\DSSOLFDWLRQ

#$

7\SLFDO+L3$3Š
V\VWHPFRQ¿JXUDWLRQ
7KH +L3$3  V\VWHP RSHUDWHV ZLWK WKH WUDQV
GXFHU PRXQWHG RQ D KXOO XQLW 6HYHUDO KXOO XQLW
PRGHOVDUHDYDLODEOHWKHVHHQDEOHWKHWUDQVGXFHU
WR EH ORZHUHG DSSUR[LPDWHO\  WR  P EHORZ
WKHNHHO$7UDQVFHLYHU8QLWFRQWDLQLQJWUDQVPLW
WHUSUHDPSOL¿HUVDQGEHDPIRUPLQJHOHFWURQLFVLV
PRXQWHGFORVHWRWKHKXOOXQLW7KHV\VWHPFDQEH
FRQ¿JXUHG ZLWK RQH RU WZR KXOO PRXQWHG WUDQV
GXFHUV7KH XVH RI WZR WUDQVGXFHUV PD\ LQFUHDVH
DFFXUDF\DQGUHGXQGDQF\
7KHV\VWHPRSHUDWLRQLVSHUIRUPHGRQD:LQGRZV
;3ŠEDVHGRSHUDWRUVWDWLRQ
 7HFKQLFDOVSHFL¿FDWLRQV
+L3$3EDVLFVSHFL¿FDWLRQV
*DWHYDOYHVL]HUHTXLUHG  PPLQFKHV
7UDQVGXFHUGLDPHWHU  PP
$FRXVWLFRSHUDWLQJDUHD  ƒ5HFRPPHQGHG
1XPEHURIDFWLYHHOHPHQWV  
 
$QJOHDFFXUDF\ G%61ƒ
  G%61ƒ
  G%61ƒ
$FFXUDF\GXDOPRGHRSWLRQ
GXDOWUDQVGXFHUV\VWHP 
G%61ƒ
 
5DQJHGHWHFWLRQDFFXUDF\ FP 7KHVSHFL¿FDWLRQVDUHEDVHGRQ/LQHRIVLJKWIURPWUDQVGXFHU
  WRWUDQVSRQGHUQRLQÀXHQFHIURPUD\EHQGLQJ6LJQDOWR1RLVH
7\SLFDORSHUDWLQJUDQJH WRP
UDWLRDVVSHFL¿HGLQZDWHULQWKH+]UHFHLYHUEDQGQR
1DUURZSRLQWLQJUHFHLYHUEHDP ƒ HUURUIURPKHDGLQJUROOSLWFKVHQVRUVDQGXVHRIFRUUHFWVRXQG
YHORFLW\2SHUDWLQJUDQJHVDUHW\SLFDODQGFRQVHUYDWLYHDQGDUH
1RWHWKDWWKHWHFKQLFDOVSHFL¿FDWLRQVDUHVXEMHFW DVVXHGE\XVLQJVXI¿FLHQWWUDQVSRQGHUVRXUFHOHYHOXSWR
WRFKDQJHZLWKRXWSULRUQRWLFH G%GHSHQGDQWRQUDQJH

+L3$3VWDQGDUGIHDWXUHV +L3$3RSWLRQDOIHDWXUHV
WUDQVSRQGHUFKDQQHOV %HDFRQ0RGH
+XOOXQLWIRUWUDQVGXFHUGHSOR\PHQW &RPSDVV7UDQVSRQGHU0RGH
:LQGRZV;3ŠEDVHGRSHUDWLRQV\VWHP 'HSWK6HQVRU7UDQVSRQGHU0RGH
5HFHLYHIUHTXHQF\EDQG ±N+] ,QFOLQRPHWHU7UDQVSRQGHU0RGH
7HOHPHWU\IUHTXHQF\EDQG ±N+] /RQJ%DVH/LQH/%/IXQFWLRQDOLW\
7UDQVPLWIUHTXHQF\EDQG ±N+] *HRJUDSKLFDO/%/&DOLEUDWLRQ
&RPSUHKHQVLYHRQOLQHKHOS 0XOWL8VHU/%/IXQFWLRQDOLW\08/%/
$XWRPDWLFWUDQVGXFHUDOLJQPHQWFDOLEUDWLRQ 2SHUDWRU6WDWLRQ0DVWHU6ODYHIXQFWLRQ
&RPSHQVDWLRQIRUUD\EHQGLQJ %ORZRXWSUHYHQWHU%23WHOHPHWU\IXQFWLRQ
'LVSOD\RIUD\EHQGLQJ 2IIVKRUH/RDGLQJ7HOHPHWU\IXQFWLRQ
([WHUQDO'HSWKVHQVRULQWHUIDFH 6XEPHUJHG7XUUHW/RDGLQJIXQFWLRQ
3RVLWLRQDQGDQJOHDODUPOLPLWV )DVW/%/7UDQVSRQGHU3RVLWLRQLQJPRGH
5HVSRQGHUPRGH /%/$FFXUDWH0HWURORJ\PRGH
7HOHJUDPRXWSXWWRG\QDPLFSRVLWLRQLQJV\VWHP  VWDQGDUGLQ/%/IXQFWLRQ

7HOHJUDPRXWSXWWRVXUYH\V\VWHP
7UDQVSRQGHU7HOHPHWU\IRUIXOOXWLOL]DWLRQ
'*36,QWHUIDFH
5HY'2FWREHU

.RQJVEHUJ0DULWLPH$6
6WUDQGSURPHQDGHQ   7HOHSKRQH
32%R[    7HOHID[
1+RUWHQ    ZZZNRQJVEHUJFRP
1RUZD\     (PDLOVXEVHD#NRQJVEHUJFRP
 G-882 MARINE MAGNETOMETER

O CESIUM VAPOR HIGH PERFORMANCE – Highest detection range

and probability of detecting all sized ferrous targets
O NEW STREAMLINED DESIGN FOR TOW SAFETY – Low
probability of fouling in lines or rocks
O NEW QUICK CONVERSION FROM NOSE TOW TO CG TOW –
Simply remove a stainless steel locking pin, move tow point and
reinsert. New easy carry handle built in!
O NEW INTERNAL CM-221 COUNTER MODULE – Provides Flash
Ram for storage of default parameters set by user
O NEW ECHOSOUNDER / ALTIMETER OPTION
O NEW DEPTH RATING – 4,000 psi !
O HIGHEST SENSITIVITY IN THE INDUSTRY – 0.004 nT/Hz RMS
with the internal CM-221 Mini-Counter
O EASY PORTABILITY & HANDLING – no winch required- single
man operation, 44 lbs with 200 ft cable (without weights or
depressor wing)
O COMBINE TWO SYSTEMS FOR INCREASED COVERAGE –
Internal CM-221 Mini-Counter provides multi-sensor data
concatenation allowing side by side coverage which maximizes
detection of small targets and reduces noise

Very high resolution Cesium Vapor performance is Kevlar and it's length is G-882 with Weight
now available has been incorporated into a low cost, standard at 200 ft (61 m)
Collar Depth Option
small size system for professional surveys in shallow with optional cable up to
or deep water. High sensitivity and sample rates of 500m (no telemetry). The shipboard end of the tow
total field measurements are maintained for all cable is attached to a junction box or on-board cable
applications. The well proven Cesium sensor is for quick and simple hookup to power and output of
combined with a unique new CM-221 Larmor counter data into any IBM PC computer. A rugged fiber-
and ruggedly packaged for small or large boat wound fiberglass housing provides selectable
operation. Use your computer and standard printer orientation of the sensor and therefore maintains
with our MagLog Lite™ software to log, display and operations throughout the world with only small
print GPS position and magnetic field data. Model limitations as to direction of survey in equatorial
G–882 is the lowest priced - highest performance fully regions.
operational marine mag system ever offered.
The G-882 Cesium magnetometer provides the same
The G-882 is flexible for operation in small boat, operating sensitivity and sample rates as the larger
shallow water surveys as well as deep tow deep tow model G-880. MagLogLite™ Logging
applications (4,000 psi rating, telemetry over steel Software is offered with each magnetometer and
coax available to 10Km). Being small and lightweight allows recording and display of data and position with
(44 lbs net, no weights) it is easily deployed and Automatic Anomaly Detection! Additional options
operated by one man. But add several no-foul weight include: MagMap2000 plotting and contouring
collars and the system can quickly weigh in at more software and post acquisition processing software
than 100 lbs. Power may be supplied from a 24 to 30 MagPick™ (free from our website.)
VDC battery supply or the included 110/220 VAC
power supply. The tow cable uses high strength
The G-882 system is particularly well suited for the Typical Detection Range For Common Objects
detection and mapping of all sizes of ferrous objects.
Ship 1000 tons 0.5 to 1 nT at 800 ft (244 m)
This includes anchors, chains, cables, pipelines, Anchor 20 tons 0.8 to 1.25 nT at 400 ft (120 m)
ballast stone and other scattered shipwreck debris, Automobile 1 to 2 nT at 100 ft (30 m)
munitions of all sizes, aircraft, engines and any other Light Aircraft 0.5 to 2 nT at 40 ft (12 m)
object with magnetic expression. Objects as small as a Pipeline (12 inch) 1 to 2 nT at 200 ft (60 m)
5 inch screwdriver are readily detected provided that Pipeline (6 inch) 1 to 2 nT at 100 ft (30 m )
the sensor is close to the seafloor and within practical 100 KG of iron 1 to 2 nT at 50 ft (15 m)
detection range.(Refer to table at right). 100 lbs of iron 0.5 to 1 nT at 30 ft (9 m)
10 lbs of iron 0.5 to 1 nT at 20 ft (6 m)
The design of this special marine unit is directed 1 lb of iron 0.5 to 1 nT at 10 ft (3 m)
toward the largest number of user needs. It is not Screwdriver 5 inch 0.5 to 2 nT at 12 ft (4 m)
intended to meet all marine requirements such as 1000 lb bomb 1 to 5 nT at 100 ft (30 m)
deep tow through long cables or monitoring fish 500 lb bomb 0.5 to 5 nT at 50 ft (16 m )
altitude. Rugged design with highest performance at Grenade 0.5 to 2 nT at 10 ft (3 m )
lowest cost are the goals. 20 mm shell 0.5 to 2 nT at 5 ft (1.8 m)

MODEL G-882 CESIUM MARINE MAGNETOMETER SYSTEM SPECIFICATIONS

OPERATING PRINCIPLE: Self-oscillating split-beam Cesium Vapor (non-radioactive)
OPERATING RANGE: 20,000 to 100,000 nT

OPERATING ZONES: The earth’s field vector should be at an angle greater than 6° from the
sensor’s equator and greater than 6° away from the sensor’s long axis.
Automatic hemisphere switching.
CM-221 COUNTER SENSITIVITY: <0.004 nT/ pHz rms. Typically 0.02 nT P-P at a 0.1 second sample rate or
0.002 nT at 1 second sample rate. Up to 10 samples per second
HEADING ERROR: ±1 nT (over entire 360° spin and tumble)
ABSOLUTE ACCURACY: <3 nT throughout range
OUTPUT: RS-232 at 9600 Baud
MECHANICAL:
Sensor Fish: Body 2.75 in. (7 cm) dia., 4.5 ft (1.37 m) long with fin assembly (11 in.
cross width), 40 lbs. (18 kg) Includes Sensor and Electronics and 1 main
weight. Additional collar weights are 14lbs (6.4kg) each, total of 5 capable
Tow Cable: Kevlar Reinforced multiconductor tow cable. Breaking strength 3,600 lbs,
0.48 in OD, 200 ft maximum. Weighs 17 lbs (7.7 kg) with terminations.
OPERATING TEMPERATURE: -30°F to +122°F (-35°C to +50°C)
STORAGE TEMPERATURE: -48°F to +158°F (-45°C to +70°C)
ALTITUDE: Up to 30,000 ft (9,000 m)
WATER TIGHT: O-Ring sealed for up to 9000 ft (2750 m) depth operation
POWER: 24 to 32 VDC, 0.75 amp at turn-on and 0.5 amp thereafter
ACCESSORIES:
Standard: CM-201 View Utility Software operation manual and ship case
Optional: Telemetry to 10Km coax, gradiometer (longitudinal or transverse)
MagLog Lite™ Software: Logs, displays and prints Mag and GPS data at 10 Hz sample rate.
Automatic anomaly detection and single sheet Windows printer support

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 4/03

GEOMETRICS, INC. 2190 Fortune Drive, San Jose, California 95131

408-954-0522  Fax 408-954-0902  Internet: [email protected]

GEOMETRICS Europe Manor Farm Cottage, Galley Lane, Great Brickhill, Bucks,
England MK179AB  44-1525-261874  Fax 44-1525-261867

GEOMETRICS China Laurel Industrial Co. Inc. - Beijing Office, Room 2509-2511, Full Link Plaza #18
Chaoyangmenwai Dajie, Chaoyang District, Beijing, China 100020
10-6588-1126 (1127..1130), 10-6588-1132  Fax 010-6588-1162
 Massa TR-1075
Sub-Bottom Profiling Transducers
The Massa Model TR-1075 Family consists of rugged high-power under-
water transducers designed to operate in the 2.5 to 10 KHz frequency
range. They are ideal for use in bottom mapping and sub-bottom FEATURES
profiling applications.
 High Power
The transducers are designed to be driven with a maximum input power - Up to 600 Watts @ 30%
of 600 Watts using up to a 30% duty cycle, or 200 Watts maximum for Duty Cycle
continuous operation. In shallow water, the maximum output is cavita-
tion limited. Minimum water depths of approximately 30 and 100 feet - Up to 200 Watts CW
are recommended for input power of 200 and 600 Watts respectively to
 Broadband
avoid cavitation.
- 2.5 to 10 kHz
All of the transducers in the family utilize the same resonant structure
 MaximumOperating Depth
containing a circular piston for the radiating source that is ½ wavelength
in diameter at 4 KHz. The transducers are designed to be bolted is 2,000 ft.
directly through their 4-corner integral shock mounts to a simple frame  True Piston Radiating Source
structure. This modular design allows the transducers to easily be
assembled into arrays to achieve any desired beam pattern and source - 1/2 Wavelength Diameter
level. Each transducer is terminated with a Massa C1F2 Female at 4 kHz
Underwater Connector and has a locking ring included. Mating C1M2 - 80° Conical Beam Angle
Male Connectors can be purchased separately.
 Module Design
The TR-1075E consists of the basic resonator with no electrical tuning. - Shock Mounted
Its nominal frequency of resonance is 3.5 KHz. Massa has fabricated - Easily Assembled into
TR-1075 Transducers with a wide variety of different internal tuning Arrays
networks. They have included transformers to produce different
output impedance magnitudes. Transducers have been made with both  Weight is 25 lbs.
series and parallel tuning to produce a nominal phase angle of 0 at
different frequencies. A separate inductor is required for series tuning,  Terminated with Proven
while the inductance of the primary windings of the transformer is used Reliable C1F2 Underwater
for parallel tuning. Connector

In some cases, damping resistors have been connected across the  Mates to Massa C1M2
transducer to lower its Q, which allows the use of a short tone burst Underwater Connector
excitation pulse with reduced sensitivity for operation when very close
to the sea floor. These transducers can be driven with greater input
power because some of the energy is dissipated by the resistor. Massa
APPLICATIONS
can customize a tuning network to meet any requirement, but one of  Sub-Bottom Profiling
the standard models will usually meet the needs of most customers.
 Bottom Mapping

Page 1 of 4 090407
MASSA PRODUCTS CORPORATION

Massa TR-1075 Data

TR-1075 Transducer Family Outline Drawing

(Dimensions in Inches)

Frequency
Transducer Tuned for Impedance
Model 0° Phase Magnitude Power Rating %
Number (nominal) (nominal) Duty Cycle Tuning Circuit

TR-1075E No Tuning 4,500 Ohms 600 Watts @ 30% No Tuning

@ 3.5 kHz 200 Watts @ 100%

TR-1075A 4 kHz 100 Ohms 600 Watts @ 30% Parallel

@ 4 kHz 200 Watts @ 100%

TR-1075H 3.5 kHz 250 Ohms 600 Watts @ 30% Series

@ 3.5 kHz 200 Watts @100%

TR-1075D 3.5 kHz 200 Ohms 1,000 Watts @ 30% Series

@ 3.5 kHz 335 Watts @ 100% with Shunt
Resistor

Chart Showing the Tuning Circuits for

the Standard Models of the TR-1075 Transducer Family

Page 2 of 4 All Specifications subject to change without notice. 090407

MASSA PRODUCTS CORPORATION

Massa TR-1075 Nominal Response Curves

Transmitting Voltage Receiving Voltage Impedance
Responses Sensitivities Magnitudes

Page 3 of 4 All Specifications subject to change without notice. 090407

MASSA PRODUCTS CORPORATION

Massa C1M2/C1F2 Underwater Connectors

Massa C1M2 male and C1F2 female 2-conductor in-line Underwater
Connectors were developed for the oceanographic community to
provide highly reliable underwater connection. Massa has manufac-
tured and sold over 100,000 connector pairs, and some have been
successfully used for over 20 years in the ocean. There has never been
a failure of a connector reported to Massa.

Massa typically supplies transducers with C1F2 Female Connectors

attached. C1M2 Male Connectors can be purchased separately to
complete the mating connection. The standard C1M2 is attached to a
5 foot cable with a retaining ring included, but connectors can be
fabricated with any length of cable required.
Photograph of C1M2 and C1F2
Connectors with Retaining Rings

MASSA PRODUCTS CORPORATION

280 Lincoln St., Hingham, MA 02043 U.S.A.
Tel: 781-749-4800 Fax: 781-740-2045
Toll Free in USA: 800-962-7543
E-mail: [email protected]
Web Site: www.massa.com

Page 4 of 4 090407
 SUBSEA TECHNOLOGY & RENTALS

DIGITAL SUB-BOTTOM TRANSCEIVER

The Digital Sub-Bottom Transceiver combines the highly successful Digital Sub-Bottom Transmitter with a fully featured
receiver to deliver a fully integrated pinger transceiver system.

KEY FEATURES
• Fully featured receiver • Heave compensation input
• Powerful 60kW output • O
 ptional Sub-Bottom Monitor acquisition software
• Single cycle mode power boost Applications:
• Adjustable frequency output • Towed
• Over-the-side mount
• Automatic impedance matching
• Bespoke hull mount installation

E: [email protected] W: www.str-subsea.com T: +44 (0)845 388 6383

DIGITAL SUB-BOTTOM TRANSCEIVER
In addition to the standard features offered by the Digital Sub-Bottom Transmitter, the new Digital Transceiver model
comes with a software driven front end receiver to provide a wide range of signal gain processing and data optimisation
benefits. Enhanced performance in noisy operating environments is achieved by selectable filtering including low pass, high
pass and notch filters to remove unwanted out of band noise. A dedicated hydrophone input is provided to offer additional
deployment configurations and noise rejection benefits. A selectable full wave envelope detector is included to provide
enhanced data display optimisation. The fully isolated output signal is easily integrated to industry standard data acquisitions
systems, or when delivered with the Sub-Bottom Monitor acquisition software package, digital acquisition can be performed
at source utilising the internal acquisition module. The Sub-Bottom Monitor software provides real time data display and
offers data acquisition over an Ethernet network with remote control of transmitter, receiver and acquisition parameters.

SUB-BOTTOM MONITOR SOFTWARE FEATURES FILTERS

Data Acquisition via Ethernet link and recording Selectable > 9kHz High pass filter
in industry formats Selectable < 2kHz Low frequency noise rejection filter
Signal gain processing via Autogain or Manual on screen TVG 3.5kHz to 18kHz Variable Low pass filter
Signal frequency processing with FFT and spectrum analysis 450Hz to 16kHz Dual adjustable notch filters
Bottom tracking function with water column blanking
or truncation options HYDROPHONE INPUT
Ethernet remote control of all transmit, receive, gain and +/- 17dB Gain adjustment
filtering functions Single ended or differential inputs
Navigation input logging in NMEA, GLL/GGA, CODA 15VDC output for preamp
and custom formats
Analogue signal output with annotation functions SIGNAL OUTPUT
for printed records Isolated 10V P-P

TRANSMITTER OUTPUT HEAVE COMPENSATION INTERFACE

60kW single cycle (30kW > 1 cycle) RS232 input, TSS1 data String
Average Output Power > 100W 9600-19200 baud
1-18kHz frequency
Up to 35 pings/second (power dependent) SV CORRECTION
No impedance matching necessary 1438ms – 1562ms
Transformer free output Up to 35pps
Separate or combined TX/RX mode
INPUT TRIGGER
PULSE CYCLES 3V–30V positive edge pulse
1 – 10 cycles 1ms – 10ms pulse
Isolated ground
TRANSDUCER MODELS Internal hardware trigger for test
Massa TR-1075D: 2.5kHz – 10kHz
STR TR-1014A: 10kHz – 14kHz OUTPUT TRIGGER
5V positive edge pulse
RECEIVER 1ms or 10ms pulse
TX/RX on standard combined or separate arrays Isolated ground

INITIAL GAIN POWER

-10 to + 30dB gain 85V – 264VAC, 50Hz (160W max)
TVG
0 – 40 Log Range Control CONNECTOR
TVG DELAY Amphenol DMS3102A-22-34S
0 to 25mS
20 – 100% Gain Limit Controls DIMENSIONS
Automatic attenuator for anti-saturation 19 inch rack mountable 4U
Selectable full wave envelope display for high frequency operation 520mm (L) x 430mm (W) x 180mm (H)

WEIGHT
16 kg
All information contained in this brochure may be subject to change without prior notice

E: [email protected] W: www.str-subsea.com T: +44 (0)845 388 6383

 Applied Acoustic Engineering Ltd
Marine House, Marine Park, Gapton Hall Road, Great Yarmouth, NR31 0NB, United Kingdom

CSP-N Seismic Energy Source

Key Features

 Unique dual negative voltage output

 Variable Input Power Circuitry for ‘soft
start’
 Additional safety/protection features
 All settings externally selectable
 LED fault indicators
 High current and voltage solid state
(semi-conductor) discharge method
The CSP-N seismic energy source is the driving force
behind Applied Acoustics’ Dura-Spark range of sound  Meets EC emissions regulations enabling
sources that have extremely hard wearing electrode interference-free field use
sparker tips. This durability is a consequence of the  Dual voltage technology allows operator
CSP’s reverse polarity high voltage charger and unique tuning to suit application
proprietary thyristor switching.
 Supplied in robust transit case, with HV
junction box (HVJ3001), mains lead and
Featuring all of the standard safety systems and HV connector plug
operational functions found across the entire range of
CSP energy sources, the CSP-N is also suitable for use
with the Applied Acoustics’ S-Boom and single plate
boomer systems.

Technical Specification

PHYSICAL

Size Transit Case (7U) with cover in place and handles flat: 50cm(H) x 58cm(W) x 74cm(D)
Weight CSP-N1200, case and cover: 60kg
CSP-N2400, case and cover: 63.5kg

ELECTRICAL SPECIFICATION

Mains Input 240Vac [email protected] single phase. 3 pin connector

Variable Input Power Circuitry (AVIP) ‘soft start’ circuitry

Voltage Output 2500 to 3950Vdc, 4 pin interlocked connector

Solid state semi-conductor discharge method
 CSP-N Technical Specification continued…

Output Energy Easy switch selectable in increments

CSP-N1200 50,100,150,200,250,300,350,400,450,500,550,600
700,800,900,1000,1100,1200 Joules
CSP-N2400 50,100,150,200,250,300,400,500,600,750, 800
900,1000,1250,1500,1750,2000,2250,2400 Joules

Charging Rate 2000J/second for continuous operation at 0-45°C

Capacitance CSP-N1200 208μF, 108 shot life

CSP-N2400 304μF, 108 shot life

Trigger +ve key opto isolated or isolated closure set by front panel switch
BNC connector on front panel and remote box (optional)

Repetition rate 6pps maximum

Limited by charge rate, energy level and sound source rating

Earth M8 stainless steel stud on front panel

SAFETY FEATURES

Main electronic control circuits and secondary layer of safety circuitry

Specially designed HV connector with interlock
High speed dump resistors for high voltage components
Capacitor bleed resistors
Open circuit shutdown
Timer shutdown
Output current monitor and shutdown
Over temperature shut-down
Cover and connector interlocks
Remote control available for triggering and operation

The unit’s internal design has a modular construction for ease of servicing and capacitor replacement. However, for safety reasons, only
Applied Acoustics trained engineers should attempt a repair.

COMPATIBLE SOUND SOURCES

CSP-N1200 Dura-Spark 240, 400

AA201, AA251 and AA301 Boomer plates
S-Boom System

CSP-N2400 Dura-Spark 240, 400

AA201, AA251 and AA301 Boomer plates
S-Boom System

Due to continual product improvement, specification

information may be subject to change without notice.
CSP-N1200 Seismic Energy Source/November 2014
©Applied Acoustic Engineering Ltd.
 Applied Acoustic Engineering Ltd
Marine House, Marine Park, Gapton Hall Road, Great Yarmouth, NR31 0NB, United Kingdom

Dura-Spark, Seismic Sound Source

Key Features

 Long life, durable electrodes

 Pulse stability
 High resolution sub-bottom
data, up to 25cm.
 Operator selectable source
depth
 Tip array selection from on
board junction box

Applications

 High and Ultra-High Resolution

geophysical surveys

 Single and multi-channel

acquisition

 Water depths of 5 to >1000m

The Dura-Spark has been designed to provide a stable, repeatable sound source for sub-bottom
geophysical surveys. The long life, durable electrodes produce a consistent pulse signature and keep
operational maintenance to a minimum. This provides increased survey efficiency and equipment
reliability as the sparker tips rarely need replacement.

The Dura-Spark is based on the CAT300 catamaran, providing a stable platform whilst under tow. The
catamaran has robust solid floatation and is easily deployed from all survey vessels.

The Dura-Spark consists of 3 or 5 arrays of 80 tips allowing the operator to tune the source from the
vessel to their application. This flexibility together with selectable source depth allows the source to
be used in both shallow and deep waters.

The typical operational bandwidth of the Dura-Spark is 300Hz to 1.2kHz. When coupled with the
CSP-N Seismic Power Supply the system offers 2000J/s peak discharge rate, as well as industry leading
design and safety standards.
 Dura-Spark Technical Specification

PHYSICAL

Dimensions 1700mm (L) 490mm (H) 660mm (W) frame/876mm (W) including floats
Weight Dura-Spark 240 60kg
Dura-Spark 400 70kg
Connector RMK 1/0 complete with locking collar

ELECTRICAL INPUT

Dura-Spark 240 1000J, 5J per tip to minimise bubble collapse component

1250J Maximum
Dura-Spark 400 2000J, 5J per tip to minimise bubble collapse component
2400J Maximum

SOUND OUTPUT

Sound Output Dura-Spark 240; 223dB re 1uPa at 1m (Typical)

Dura-Spark 400; 226dB re 1uPa at 1m (Typical)
Pulse Length 0.5 to 1.5ms depending on power

Number of Tips 240 Max total. 3 x 80

Operator selected; 80 (1 x 80) or 160 (2 x 80) or 240 (3 x 80)
400 Max total 5 x 80
Operator selected; 80 (1 x 80) or 240 (3 x 80) or 400 (5 x 80)

COMPATIBILITY

Source Seismic Power Supply HV Cable

Dura-Spark 240 CSP-N 1200 Negative HVC-3500

Dura-Spark 400 CSP-N 2400 Negative HVC-3500

TYPICAL PULSE SIGNATURES

Dura Spark 240 Typical Pulse Signature at 1000J recorded @ 2m Dura Spark 400 Typical Pulse Signature at 2400J recorded @ 2m

Due to continual product improvement, specification

information may be subject to change without notice.
Dura-Spark/March 2015
©Applied Acoustic Engineering Ltd.
 STD/CTD - model SD204
with multi-parameter & auto range facilities

• Salinity • Conductivity
• Temperature • Depth
• Sound velocity • Oxygen
• Turbidity (auto range) • Fluorescence (auto range)

SD204 with optional

sensors

SD204 in transport/storage case

Features:
• Compact & robust design
• Long term stability sensors
• High memory capacity
SD204
• Sonar equipment compatibility
• Year-long battery capacity
• Depth to: 6000 meters
• Windows based software
• Output in physical units
• On-line plotting
• Auto range for turbidity & fluorescence

SAIV A/S Environmental Sensors & Systems

Post Office Box 3513
5845 Bergen, Norway
Tel: + 47 56 11 30 66, Fax: +47 56 11 30 69, e mail: [email protected], web: www.saivas.no
Street address: Nygårdsviken 1, 5164 Laksevåg
STD/CTD - model SD 204
The SD204 measures, calculates and records sea water conductivity, salinity, temperature, depth (pressure), sound velocity
and water density. Three optional sensors can be added, f. example: dissolved oxygen, fluorescence and turbidity. For
optional sensors with several sensitivity ranges, the SD204 has auto range capability. Data are recorded in physical units.
The accompanying software, SD200W, contains versatile functions for programming, post- and online data processing and
presentations: - multigraph, online plotting, density and depth calculations (weighed profile). The program is continuously
extended according to customer’s requests. The programmed settings and calibration coefficients are maintained in nonvolatile
eeprom, and will not be changed/lost if power is disconnected. Robustness and complete protection from leakage is obtained
by vacuum molding the electronic and all other components in solid polyurethane. On/Off-switching is by a magnetic key or
from keyboard. A sealed battery compartment contains two replaceable C-cells. In practical operation the
battery capacity is sufficient for continuous year-around operation with good margin.
The instrument is equipped with a mooring bar with a shackle at each end. Data are
recorded in physical units and simultaneously transmitted via an RS232 I/O watertight
connector for on-line use.
For remote readout and monitoring, the manufacturer offers several options:
Communication Unit CU901, for two-way communication via Iridium satellite,
GPRS with embedded web server, GSM and UHF/VHF,

Specifications:
Conductivity: Inductive cell Turbidity: (optional)
Range: 0 to 70 mS/cm Sensor type: Backscatter
Resolution: 0.01 mS/cm Ranges: 12.5, 62.5, 250, 750 FTU
Accuracy: +/- 0.02 mS/cm selectable/auto range
Linearity: < 2%
Salinity: Calculated from C,T & D
Range: 0 to 40 ppt Real time clock: +/- 2 sec/day
Resolution: 0.01 ppt
Modes: STD/CTD with/without sound
Accuracy: +/- 0.02 ppt
velocity, oxygen and optional sensor.
.
Temperature:
Intervals: 1 sec to 180 min.
Range: -2 to +40’C
Resolution: 0.001’C Memory: CMOS SRAM
Accuracy: +/- 0.01’C Capacity: 56000 data sets of STD/CTD
Response time : 0.2 sec
Data output: RS232 ASCII code.1200-9600 baud
Pressure: Specify desired depth range with order 1 start, 7 data, 1 stop, even parity or
Ranges: 500, 1000, 2000, -- 6000 m) 1 start, 8 data, 1 stop, no parity
Resolution: 0.01 dbar (m) selectable via menu
Accuracy: +/- 0.01% FS (-2 to +40’C)
Response time: 0.1 sec Power: 2 ea. 3.6V lithium C-cells.
Recommended type: SAFT LSH14
Sound velocity: Calculated from S,T &D (Sufficient for1.500.000 data sets)
Range: 1300 to 1700 m/s External: 10 – 30VDC
Resolution: 1 cm/s
Accuracy: +/- 5 cm/s Material: Vacuum molded polyurethane and
titanium
Dissolved oxygen: (optional) Dimensions: Length 400 mm. Diameter 60 mm
Sensor type: SAIV205 Weight: In air: 2 kg. In water: 0,8 kg.
Range: 0 to 20 mg/l Packing: Suitcase (534x427x157 mm)
Grossweight 5,5 kg
Resolution: 0.01 mg/l
Accuracy: +/- 0.2 mg/l
Accessories: On/Off magnetic key,
(included) PC communication cable 2,5m,
Fluorescence: (optional)
MINISOFT SD200W program
Sensor type: Fluorescein/ Chlorophyll/Rhodamine/CDOM Operating Manual
Ranges: 2.5, 7.5, 25, 75 ug/l
selectable/auto range Warranty: Two years against faulty materials
Resolution: 0.03 ug/l and workmanship

SAIV A/S Environmental Sensors & Systems, Post Office Box 3513 5845 Bergen, Norway
Tel:+47 56 11 30 66 Fax:+47 56 11 30 69 e-mail: [email protected] web: w ww. saiv a s.no
 12/29/2014

Features & Benefits

• Light and easy to handle: only 44.5 mm diameter, up

to 240 channels in 8-channel sections. Hand-
deployable up to 400m.

• 100% solid construction: bulge waves are a thing of

the past

• Digital sections: better quality data, less time

deploying and troubleshooting

Description • Full-featured yet simple: no 30-day training program

required
Introducing the ultimate in marine seismic
fidelity: the GeoEel SolidTM from Geometrics. • Wide bandwidth for more applications: samples at 1/8
Built on our experience and success with the to 2 ms for petroleum, engineering or sub-bottom
profiling
popular GeoEelTM digital streamer, the GeoEel
Solid combines superior electronics with a
• Environmentally friendly and non-flammable: solid
patented solid active section design that polyurethane, easily ships by air, no oil to spill
delivers higher-quality data than ever before.
• Free software upgrades forever: no yearly licensing
The GeoEel Solid digital hydrophone streamer fees
is the smallest diameter solid design available.
At only 44.5 mm, the GeoEel Solid is easy to • No costly topside hardware required: uses any PC and
deploy, easy to transport and easily shipped by standard Ethernet
air. The 100% solid construction, coupled with
our proprietary polymer hydrophone design, •
eliminates bulge waves and other cable-borne
noise, yielding very low towing noise at lower
frequencies than any liquid streamer.

The GeoEel Solid communicates via 100 mbs

Ethernet with the Geometrics CNT-2
controller, running field-proven acquisition
software that is used on over 70 installations
worldwide. And the GeoEel Solid is designed
by Geometrics, known for over 40 years as an
industry leader in rugged, reliable and well-
supported instrumentation.
Data courtesy Fugro Consultants, Inc.

2190 Fortune Drive, San Jose, CA 95131 • P:408-954-0522 • F: 408-954-0902 • www.geometrics.com

 GeoEel Solid™ TECHNICAL SPECIFICATIONS
Digital Solid Streamer
A/D Converter Modules Tow Cable
Channels: 8 per A/D module Weight: 0.5 Kg/m
Sample intervals: 1/8, 1/4, 1/2, 1, 2 ms Strain member: Kevlar
Programmable gain: 0 dB, 8 dB, 18 dB, 30 dB, 42 dB Working load: 900 Kg
Anti-alias filter: Set by sample interval, down 135 dB at Diameter: 18.5 mm
stop-band
Maximum input range: 1.59Vrms Stretch and Vibration Isolation Sections
Resolution: 24 bits including sign
Input impedance: 126.8K Ohms, paralleled by 2.4 nF Length:10, 25 or 50 meters
Dynamic range: 120dB Typical @ 1ms Diameter:41 mm (stretch) or 44.5 mm (isolation)
Common mode rejection: >110 dB Ballast fluid:
Gel (stretch only)
Record length: Up to 30,000 samples Stretch ratio:
15% (stretch only)
Dead time: Up to 256 samples Bird coil:
ION Model-578 compatible
Continuous recording mode: Available, with GPS synchronization (vib section only)
Noise floor: 0.3 µV at 2 ms Working load: 560 Kg
QC tests: Leakage and capacitance of hydrophone Strain member: Zylon (isolation), Vectran (stretch)
elements, noise, offset, harmonic distortion
and gain similarity Streamer Power Supply Unit
Power consumption: 600 mW/channel Power Requirements: 115/230 VAC, 3/1.5 Amp max, 50/60 Hz
Calibration oscillator: 100 Hz, 0.3 µV to 600 mVrms Voltage to Streamer: 36-60 VDC
Dimensions: 44 mm diameter x 330 mm long I/O Communications: I/O Communications: 100Base TX Fast
Weight: 900 g
Ethernet, IEEE 802.3 compliant
Packaging material: Titanium
Trigger Requirements: Isolated input, positive or negative TTL
Connectors: 38-pin custom Glenair
Testing: Cable leakage and resistance
Hydrophone Sections Optional Auxiliary Inputs: 8 analog channels with 24-bit resolution
Ethernet Connection: RJ-45
Number of channels: 8 per section Trigger Connection: BNC
Group interval: 1.5625, 3.125, 6.25, or 12.5m
Hydrophones per group: 4-6 (typical; up to 12 upon request)
Group sensitivity: -194 + 1.5 dB re 1 V/mPa
Low cut filter: 10 + 0.5 Hz (100 and 50m)
15 + 1 Hz (25m and 12.5m)
Hydrophone type: Proprietary polymer
Bird coil: ION Model-578 compatible
Operation depth: 30 m
Diameter: 44.5 mm
Weight: ~156 Kg / 100m
Strain member: Zylon
Working load: 560 Kg
Minimum bend radius: 1m

GEOMETRICS INC.
2190 Fortune Drive, San Jose, California 95131, USA
Tel: 408-954-0522 Fax: 408-954-0902
Email: [email protected]

GEOMETRICS EUROPE
20 Eden Way, Pages Industrial Park, Leighton Buzzard LU7 4TZ, UK
Tel: 44-1525-383438 Fax: 44-1525-382200
Email: [email protected]
Photo courtesy JAMSTEC, Yokosuka, Japan
GEOMETRICS CHINA
Laurel Technologies, Ste 1807-1810, Kun Tai Int'l Mansion, #12B, Chaowai St.,
Beijing 100020, China
Controller
Tel: 86-10-5879-0099 Fax: 86-10-5879-0989 PC-based, running Geometrics CNT-2 software. Multiple
Email: [email protected] shot and gather windows, bar graph noise displays,
windows for shot timing, gun energy, brute stack, tape
www.geometrics.com status, spectral analysis. Auto-switching between storage
devices, dual tape writing. Supports multiple printers. Full
log kept of all parameter changes. Integrates navigation,
gun, and bird data into SEG-D or SEG-Y header.

Updated 12/29/14 cl
Specifications subject to change without notice

SEISMOGRAPHS • MAGNETOMETERS • GEOELECTRICAL INSTRUMENTS

 cNODE® Transponders
Maxi, Midi and Mini

Introduction

cNODE® is a family of transponders for underwater acoustic

positioning and data link. The transponders operate together with both
HiPAP®, HPR and cPAP® transceivers.
cNODE® utilises Cymbal® acoustic protocol and is compatible with the
HiPAP®/HPR 400 channels and telemetry.
cNODE® is designed to cover a large range of applications and this
is made possible by the modular design and a variety of different
transducers, internal and external sensors, housing materials and other
add-on functions.

cNODE® is easy to set-up, operate and maintain. Both new

configuration and software can be downloaded from TTC 30 without
opening the transponders. The floating collar and release design make
the launch/recovery operation safe and easy. Spare parts for cNODE®
are based on the main modules.

The cNODE® transponder family consists of the models Maxi, Midi

and Mini.

Common for all cNODE®

transponders

• Operates together with HiPAP®, • Internal tilt sensor ± 90°.

HPR and cPAP® transceivers. • Pressure relief valve and vent
• Compatible with both Cymbal® screw (safety devices).
acoustic protocol for positioning • External connector for
and data link, and HiPAP®/HPR transponder configuration and cNODE® Family:
400 channels and telemetry. software update via serial line Maxi 34-30V30H-R (Left)
• SSBL positioning. (TTC 30). Midi 34-180 (Middle)
• LBL positioning. • Modular design such that Mini 34-180 (Right)
• Range accuracy of 0,01 m the transducer, transponder
between transponders. electronics, battery pack and
• Acoustic data link for command optional add-on’s can be replaced
and data transfer. individually.
• Both transponder and responder
functions.

Top section Bottom end

Tranducer module Tube cap module

cNODE® modular design

Maxi/Midi - Models and standard features

Examples of models:
Maxi Midi
Depth rating - MF models: 4000 m 34-180 34-30V-I-St 34-180
Operating temperature: - 5 °C to + 55 °C 34-30V30H-R 34-30V-II-St 34-30V
34-30V30H-Dx-R 34-30V-St 34-30V30H
34-30V-Si 34-30V30H-R-St 34-S-R

Transducers
TD180 TD30V TD30V30H

Frequency band: Medium Frequency (MF) Medium Frequency Medium Frequency

Beam width: 180° 30° vertical 30° vertical/30° horizontal
Receiver sensitivity: 100 dB 85 dB 85 dB
Source level - max: 190 dB 206 dB 206 dB/190 dB
Material: Aluminium/Stainless steel Aluminium/Stainless steel Aluminium/Stainless steel

Top end caps Top section modules

Split transducer (S) Depth sensor (Dx) Multi Sensor Module (Msm)
The module includes the
following high accuracy
sensors:
• Depth: 0,01% FS
High accuracy depth • Inclinometer: 0.05°
Material: Aluminium sensor • Sound velocity: ± 0.02 m/s
Cable length: 6 m Accuracy: 0.01% FS Material: Aluminium
Material: Aluminium

Bottom end cap modules

Basic end cap Release mechanism (R) Sensor interface (Si) Inclinometer (I)

Material: Aluminium/ Safe working load: 500 kg Interface external sensors Internal X and Y inclinometer
Stainless steel Material: Aluminium/ Number of sensors: 3 Range: ± 60°
Stainless steel Serial line: RS-232/-485/-422 Accuracy: 0.25°
Material: Aluminium Material: Stainless steel

Tubes Batteries
Maxi Midi Maxi Midi

Type: Lithium, non- Type: Lithium, non-

Material: Aluminium/ Material: Aluminium rechargeable rechargeable
Stainless steel Coating: Polyurethane Battery lifetime Battery lifetime
Coating: Polyurethane • Quiescent: 2.5 years • Quiescent: 1.25 years
• No. of replies: 0.7 to • No. of replies: 0.35 to
11.5 millions 5.75 millions
External sensors Floating collar
External Inclinometer (II)
Examples of other external
• To be used sensors:
together with • Sea current sensor
Inclinometer (I) • Temperature sensor
• Pressure sensor
External X and Y inclinometer • Heading sensor Max. operation depth: 4000 m
Range: ± 60° • Doppler Velocity Log Safe working load on release unit: 500 kg
Accuracy: 0.25° • Environmental sensors Minimum anchor weight: 60 kg
Material: Stainless steel

Mini - Models and standard features

Examples of models:
Depth rating - MF models: 4000 m
Depth rating - LF models: 7000 m 34-180 17-180-St
Operating temperature: - 5 °C to + 55 °C 34-40V 31-80V-D-St

Transducers
TD180 TD40V TD80V TD180LF

Frequency band: Medium Frequency Medium Frequency Medium Frequency Low Frequency (LF)
Beam width: 180° 40° vertical 80° vertical 180°
Receiver sensitivity: 100 dB 90 dB 85 dB 100 dB
Source level - max: 190 dB 203 dB 188 dB 188 dB
Material: Aluminium Aluminium Stainless steel Stainless Steel
Depth rating: 1000 m

Top section modules Tubes Bottom end cap modules

Depth Sensor (D)

Accuracy: 0.1% FS Material: Aluminium/Stainless steel Material: Aluminium/Stainless steel

Material: Stainless steel Coating: Polyurethane

Battery Battery charger Power AC/DC unit

Type: NiMH, rechargeable Input: 110/230 Vac

Battery lifetime: Output: 15 Vdc/300 W
• Quiescent: 60 days Battery charger, NiMH Material: Aluminium
• No. of replies: 40.000 to 750.000

Accessories
TTC 30 - Transponder Test and Configuration unit*
Frequency band: MF
(Cd302
04c)

The unit comes with:

• Test Transducer
• Serial Line Cable * See separate TTC 30 Product
• Mains Power Cable Specification for more information.
Maxi outline drawings
Maxi 34-30V30H-R 1366

Ø144
Ø184
Tube length: 805 mm
Weight in air: 30 kg
Weight in water: 13 kg

Maxi 34-180 1014

Ø144

166
Weight in air: 28 kg
Weight in water: 12 kg

Floating collar outline drawing

870
358
Weight in air: 70 kg
Nominal Buoyancy: 30 kg

Midi outline drawing 455

Midi 34-180
704.5
535
Ø144
166

Tube length: 495 mm

Weight in air: 16.5 kg
Weight in water: 8.5 kg

Mini outline drawing

Mini 34-40V 598
101.5
(Cd302048)

527
Ø100

Ø85

Tube length: 496 mm

Weight in air: 6.7 kg
Weight in water: 3.4 kg 343339 / Rev. B / May 2011

Kongsberg Maritime AS
Strandpromenaden 50 Telephone: +47 33 03 41 00
P.O.Box 111 Telefax: +47 33 04 47 53
N-3191 Horten, www.kongsberg.com
Norway [email protected]
 Transducer TC2122
Dual-Frequency Survey Echosounder Transducer

TC2122
• Narrow beams Model TC2122 is a 33kHz and 200kHz dual frequency transducer ideal
for navigation and hydrographic echosounder systems. The transducer has
• High acoustical performance excellent piezoceramic elements which will ensure the highest reliability and
quality in echosounding. The transducer will fit ATLAS SW 60/28/6029
• Compact design
housing and RESON steel housings.
• Compatible with ATLAS
SW60/28/6029 housing.

• Electrical compatible with

most 33kHz and 200kHz TECHNICAL SPECIFICATIONS
echosounders. Resonant Frequency: 33kHz ±2kHz 200kHz ±5kHz
Transmitting sensitivity: 168dB ±3dB at 33KHz 174dB ±3dB at 200KHz (re 1µPa/V at 1m)
Receiving Sensitivity: -177dB ±3dB at 33KHz -187dB ±3dB at 200KHz (re 1µPa/V)
Impedance: 80ohm ±24ohm at 33kHz and 200kHz
Beam width: 22°±2° at 33KHz 9,5°±1° at 200kHz
Beam shape: Conical
Max input power: 1000W at 33kHz 450W at 200kHz (at 1% duty cycle)
Operating depth: 30m
Survival depth: 50m
Operating temperature range: -2°C to +35°C
Storage temperature range: -30°C to +50°C
Weight in air,with cable: 5kg
Housing: PVC
Cable (length and type): 33m FALMAT Type FM088095-7, 4x1 (2 x twisted pair) PUR Jacket,
WATER BLOCK, Kevlar Braid 800lbs breaking strength (O.D. 11mm) - pigtail
 Transducer TC2122
Dual-Frequency Survey Echosounder Transducer

Typical graphs 33kHz

HorizontalTC2122 Transmitting
Directivity Pattern Directional Response ReceivingReceiving
SensitivityResponse
[dB re 1V/µPa re ]1V/µPa @ 1m]
@ 1m
[dB
o -170
0
o 0 dB o
-30 30 33kHz
-3 dB
-175
-10 dB

o o
-60 60 -180
-20 dB

-185
-30 dB

o o
-90 -40 dB 90 -190

-195
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Frequency [kHz]

Transmitting Sensitivity
Transmitting [dB re 1µPa/V
Response [dB@re ]
1m1µPa/V @ 1m] Impedance TC2122 Impedance Summary
175 100

170

50

165
Ω

160
0

155
Resistance
Reactance
Impedance
-50
150 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Frequency [kHz]
Frequency [kHz]
 Transducer TC2122
Dual-Frequency Survey Echosounder Transducer

Typical graphs 200kHz

TC2122 Transmitting
Horizontal Directivity PatternDirectional Response ReceivingReceiving
SensitivityResponse
[dB re 1V/µPa re ]1V/µPa @ 1m]
@ 1m
[dB
o -184
-10
o 0 10
o
o o
-20 20 -186
o o
-30 30
-188
0 dB
-3 dB -190

-10 dB -192

-194

-20 dB
-196

-198
-30 dB 190 192.5 195 197.5 200 202.5 205 207.5 210 212.5 215 217.5 220 222.5 225 227.5 230
Frequency [kHz]
200.00 kHz

-40 dB

Transmitting Sensitivity
Transmitting [dB re 1µPa/V
Response [dB@re ]
1m1µPa/V @ 1m] Impedance TC2122 Impedance Summary
174 200

173
150

172
100

171
50
Ω

170
0

169
-50
168
-100 Resistance
167 Reactance
Impedance
-150
166 190 192.5 195 197.5 200 202.5 205 207.5 210 212.5 215 217.5 220 222.5 225 227.5 230
190 192.5 195 197.5 200 202.5 205 207.5 210 212.5 215 217.5 220 222.5 225 227.5 230 Frequency [kHz]
Frequency [kHz]
 Transducer TC2122
Dual-Frequency Survey Echosounder Transducer

Outline Dimensions

RESON reserves the right to change specifications without notice. © 2006 RESON A/S
For Acoustical Measurement Accuracy please refer to www.reson.com or contact sales.

RESON A/S RESON Inc. RESON Offshore Ltd.

Denmark USA United Kingdom
Tel: +45 4738 0022 Tel: +1 805 964-6260 Tel: +44 1224 709 900
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Version: B089 090107 / A4

RESON GmbH RESONB.V. RESON (Pte.) Ltd.

Germany The Netherlands Singapore
Tel: +49 431 720 7180 Tel: +31 (0) 10 245 1500 Tel: +65 6725 9851
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]