UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based On Windows) (VersionA)
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based On Windows) (VersionA)
Network Convergence
Management System V2.0R4
Code: MN000003318
September 2017
Thank you for choosing our products.
Version
Version Description
Related Documentation
Document Main Content Phase to Use
Introduces the functions, application
UNM2000 Network
scenarios and technical specifications
Convergence Management Network Planning
of the UNM2000 Network
System Product Description
Convergence Management System.
Network
UNM2000 Network The meaning and usage constraints of
maintenance /
Convergence Management shortcut menus and buttons in the
service
System GUI Reference menus and windows
deployment
Intended Readers
I
Terminology Conventions
Terminology Convention
FiberHome UNM2000 Network Convergence Management
UNM2000
System
Symbol Conventions
Cascading
→ Connects multi-level menu options.
menu
Bidirectional
↔ The service signal is bidirectional.
service
Unidirectional
→ The service signal is unidirectional.
service
II
Operation Safety Rules
The computer case, UPS power supply and switch (or hub)
should be connected to protection earth ground.
III
Do not perform service configuration or expansion during service
busy hours via the network management system.
IV
V
VI
Contents
Preface...................................................................................................................I
1 Installation Overview.......................................................................................1
2 Installation Process.........................................................................................6
5 FAQ..............................................................................................................76
5.6 New Alarms Failed to Be Reported in Real Time / New ONU List
Failed to Be Refreshed ...................................................................82
Before installing the UNM2000, you should be familiar with the operating mode and
configuration requirement of the UNM2000, so as to complete the installation
smoothly.
Operating Mode
Version: A 1
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The UNM2000 uses the Client / Server architecture. The UNM2000 client end and
server end can be installed on one computer, or on two computers respectively. The
server end supports the access and operations of multiple client ends.
The installation package of the UNM2000 server end includes the following two
components and you can select the components to be installed as required.
Note:
u The UNM2000 supports the remote installation of the client end. You
can access the server in which the client end distribution program
locates to download and install the client end via the IE browser.
The following introduces the hardware and software configuration requirements for
the computer on which the UNM2000 is to be installed.
Server End
2 Version: A
1 Installation Overview
Network CPU Clock Rate CPU Mem- Hard Hard Disk Format Network Card
Scale Quantity ory Disk
Space
Version: A 3
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Client End
Table 1-2 shows the hardware configuration requirements of the UNM2000 client
end.
Network Scale CPU Clock Rate CPU Mem- Hard Disk Hard Disk Video Card
Quantity ory Space Format
Equivalent to
The format of the
more than
disk on which the
1000 OLTs that
Intel XeonE5-2637V2 UNM2000 will be 1 GB discrete
are fully 1 16G 1*2TB
(4-core), 3.5GHz installed (disk D graphics
configured and
by default)
connected with
should be NTFS
ONUs
Equivalent to The format of the
500 to 1000 disk on which the
OLTs that are Intel i3-4130 (2-core), UNM2000 will be 1 GB discrete
1 8G 1*1TB
fully configured 3.4GHz installed (disk D graphics
and connected by default)
with ONUs should be NTFS
Equivalent to The format of the
100 to 500 disk on which the nVIDIA
Intel Core i5-4200U (1.
OLTs that are UNM2000 will be GT720M 1GB
6G-2.6G/3M) (2-core), 1 8G 1*500GB
fully configured installed (disk D discrete
3.4GHz
and connected by default) graphics
with ONUs should be NTFS
Equivalent to The format of the
less than 100 disk on which the
Intel Corei5-4200U (1. Intel HD 4400
OLTs that are UNM2000 will be
6G-2.6G/3M) (2-core), 1 4G 1*500GB integrated
fully configured installed (disk D
3.4GHz graphics
and connected by default)
with ONUs should be NTFS
The software requirements for the computer running the UNM2000 server end are
as shown in Table 1-3.
4 Version: A
1 Installation Overview
Solaris 11 (64-bit)
The software requirements for the computer running the UNM2000 client end are as
shown in Table 1-4.
Caution:
Version: A 5
2 Installation Process
The installation includes the initial installation and upgrade installation. You can
install the UNM2000 according to the installation flowchart.
Initial Installation
Upgrade Installation
6 Version: A
2 Installation Process
The following introduces how to install the server end and the client end for the first
time.
When installing the UNM2000 server end for the first time on Windows operating
system (OS), you can refer to the flowchart shown in Figure 2-1 or Figure 2-2
according to the type of database to be used.
Note:
Version: A 7
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Figure 2-1 Flowchart of Installing the Server End for the First Time (for MySQL)
8 Version: A
2 Installation Process
Figure 2-2 Flowchart of Installing the Server End for the First Time (for SQL Server)
When installing the UNM2000 client end for the first time under the Windows
operating system, users can refer to the flowchart shown in Figure 2-3.
Version: A 9
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Figure 2-3 Flowchart of Installing the Client End for the First Time
When upgrading the UNM2000 server end on the Windows OS, you can refer to the
flowchart shown in Figure 2-4.
10 Version: A
2 Installation Process
Version: A 11
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The UNM2000 supports automatic upgrading of the client end. Upon startup, the
client end will check for updates and upgrade itself automatically, so as to
synchronize the version of the client end with that of the server end.
12 Version: A
3 Installing the UNM2000
The following introduces how to install the UNM2000 for the first time on the
Windows OS.
Version: A 13
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The following introduces how to install the UNM2000 server end for the first time on
the Windows OS.
To ensure the security of the system, the system firewall denies the access to the
system ports. In order to use the UNM2000 normally, you need to enable the firewall
and set a firewall custom rule to allow the UNM2000 to access specific ports.
Prerequisite
Procedure
2. Select the Inbound Rules or Outbound Rules in the left pane and click New
Rule in the right pane to display the New Inbound Rule Wizard or New
Outbound Rule Wizard dialog box.
14 Version: A
3 Installing the UNM2000
4. See Table 3-1 to select the corresponding protocol, enter the port number and
click Next. The port 3306 is used as an example to introduce how to add an
inbound rule.
The port to be
used by the
Description
0/0 TCP 52001:52399 52001:52399 ICE or the
information
application
program.
Description
0/0 UDP 161 161
information ManagerTRAP
Description port.
0/0 UDP 162 162
information
Description MySQL
0/0 TCP 3306 3306
information database port
Version: A 15
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
16 Version: A
3 Installing the UNM2000
7. Enter 3306 in the Name textbox and relevant description in the Description
(optional) textbox. Then click Finish to complete adding the inbound rule for
the port.
8. Repeat Step 2 to 7 until all inbound and outbound rules are added.
Version: A 17
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Prerequisite
u The hardware and software configurations of the server meet the requirements
described in System Configuration Requirements.
u If Microsoft Visual Studio 2008 is installed on the server, you need to install the
VS-2008 sp1 first.
Note:
Procedure
2. Double-click setup.exe in the file folder to display the SQL Server Installation
Center dialog box.
18 Version: A
3 Installing the UNM2000
3. Click Installation in the left pane, and select New installation or add features
to an existing installation. in the right pane.
Version: A 19
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
4. The system will check the installation program support rules. Then click OK in
the SQL Server 2008 R2 Setup dialog box that appears.
Note:
If the check fails, you need to solve all problems causing failures
according to the prompt, and then reinstall the SQL server database.
5. Select the SQL Server 2008 R2 version to be installed, type the product key,
and click Next.
20 Version: A
3 Installing the UNM2000
Version: A 21
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
8. The system will check the installation program support rules. Then click Next in
the SQL Server 2008 R2 Setup dialog box that appears.
Note:
If the check fails, you need to solve all problems causing failures
according to the prompt, and then reinstall the SQL server database.
22 Version: A
3 Installing the UNM2000
Version: A 23
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
11. The system will check the installation rules. Then click Next.
24 Version: A
3 Installing the UNM2000
Version: A 25
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
1) Click Use the same account for all SQL Server services, select NT
AUTHORITY\NETWORK SERVICE as the account name and click OK.
26 Version: A
3 Installing the UNM2000
2) Click Next in the displayed SQL Server 2008 R2 Setup dialog box.
Version: A 27
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
16. Do not select sending the error reports, and then click Next.
28 Version: A
3 Installing the UNM2000
17. The system will check the installation configuration rules. Then click Next.
Version: A 29
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
18. Verify the functions of SQL Server 2008 R2 to be installed, and click Install.
19. After the installation is completed, click Close in the dialog box as shown
below.
30 Version: A
3 Installing the UNM2000
Prerequisite
u The hardware and software configurations of the server meet the requirements
described in System Configuration Requirements.
Procedure
Decompress the MySQL file folder to the root directory of disk D of the network
management server.
Version: A 31
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Caution:
1) Select Start→Run, and type cmd in the Open text box of the dialog box
that appears, as shown below.
2) Click OK to display the CLI window and then execute the following
commands.
D:\>cd MySQL\bin
32 Version: A
3 Installing the UNM2000
Note:
2) See Table 3-2 to check and set the corresponding parameters in the my.
ini file.
Parameter Value
[client] default-character-set gbk
key_buffer_size 256M
max_allowed_packet 64M
table_open_cache 256
sort_buffer_size 256K
read_buffer_size 64K
[mysqld] read_rnd_buffer_size 256K
myisam_sort_buffer_size 64M
myisam_recover_options BACKUP, FORCE
thread_cache_size 8
query_cache_size 16M
thread_concurrency 8
Version: A 33
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Parameter Value
max_connections 500
character-set-server gbk
innodb_data_home_dir D:\MySQL\data/
innodb_data_file_path ibdata1:256M:autoextend
innodb_buffer_pool_size 512M
innodb_additional_mem_pool_size 8M
innodb_log_file_size 256M
innodb_log_buffer_size 8M
innodb_flush_log_at_trx_commit 2
innodb_lock_wait_timeout 50
innodb_file_per_table 1
[mysqldump] max_allowed_packet 64M
key_buffer_size 128M
sort_buffer_size 128M
[myisamchk]
read_buffer 2M
write_buffer 2M
34 Version: A
3 Installing the UNM2000
3) Select Automatic from the Startup type drop-down list and click Start to
start the MySQL service. After the service is started, the process box will
be closed automatically.
Subsequent Operation
After installing the MySQL database, configure the environment variables of the
database. The configuration procedures are as follows:
Version: A 35
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Caution:
If the Java environment variables are not configured, you cannot query
the Java version. See How to View the Java Version for the query
method.
2. In the left area of the System window, click Advanced system settings to
open the Advanced tab of System Properties dialog box.
36 Version: A
3 Installing the UNM2000
4. In the System variables list box, select the Path variable and click Edit to
display the Edit System Variable dialog box, as shown below.
Note:
Version: A 37
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The following introduces how to install the UNM2000 for the first time on the
Windows OS.
Prerequisite
u The hardware and software configurations of the server meet the requirements
described in System Configuration Requirements.
u The system firewall inbound/outbound rules have been set, or the system
firewall and anti-virus software have been disabled.
Procedure
1. Double-click the UNM2000 installation software, and click Next in the displayed
dialog box.
38 Version: A
3 Installing the UNM2000
Note:
Version: A 39
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
40 Version: A
3 Installing the UNM2000
6. Set the Tomcat installation path (the default installation path D:\ApacheTomcat
is recommended), and then click Next.
Version: A 41
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
8. Set the Tomcat port (the default port 8080 is recommended), and then click
Next.
42 Version: A
3 Installing the UNM2000
9. Specify the server deployment mode. Select the default Centralized and click
Next.
Note:
This manual only introduces the single-instance installation mode (that is,
deploying all services of the server end on the same computer) and
therefore Centralized is selected.
Version: A 43
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
10. Specify the IP address of the computer running the server end, and then click
Next.
44 Version: A
3 Installing the UNM2000
4 Set the MySQL parameter, set the database of the UNM2000 server end
according to Table 3-3 and then click Next.
Item Description
Host Sets the IP address of the computer running the server end.
DataBase Password Sets the database password. The default value is vislecaina.
Version: A 45
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
4 Set the SQL Server parameter, set the database of the UNM2000 server
end according to Table 3-4 and then click Next.
Item Description
Host Sets the IP address of the computer running the server end.
46 Version: A
3 Installing the UNM2000
Version: A 47
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
14. The installation of the program starts. In the alert box displayed a while later,
click Finish.
15. If you click No in the displayed alert box, the computer will not be restarted
immediately.
Note:
48 Version: A
3 Installing the UNM2000
Prerequisite
Procedure
1. Select Start→Run, and type cmd in the Open text box of the dialog box that
appears, as shown below.
2. Click OK to display the Command Line Interface (CLI) window and then
execute the following commands.
C:\Users\Administrator>d:
D:\>cd unm2000\server\tool
D:\unm2000\server\tool>installdb.bat –i
Version: A 49
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The procedures may vary with the database selected. The following figure
takes the initialization procedure of SQL Server as an example.
50 Version: A
3 Installing the UNM2000
Version: A 51
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
52 Version: A
3 Installing the UNM2000
Procedure
2. View the services listed in Table 3-6 in the Services window and check
whether the status of the services is Started. If any service is not started, select
the service and click Start Service to start it.
Version: A 53
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The UNM2000 client must be installed and running with the Java software, and
therefore you need to install the Java environment before installing the UNM2000
client.
54 Version: A
3 Installing the UNM2000
Background Information
If the JDK has been installed on the computer running the UNM2000 client end, but
its version does not meet the requirements described in Software Configuration
Requirements, you need to uninstall it. See How to View the Java Version.
u If the operating system of the client end is Windows x86 (32-bit), please install
the jdk-6u38-windows-i586.exe.
u If the operating system of the client end is Windows x64 (64-bit), please install
the jdk-6u38-windows-x64.exe.
The following takes the installation of client end on the Windows 7 system as an
example for introduction.
Procedure
2. Keep the default settings. Click Next and the installation progress will be
displayed.
Version: A 55
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
3. The default installation path is recommended. Click Next and the installation
progress will be displayed.
56 Version: A
3 Installing the UNM2000
Subsequent Operation
After installing the JDK, configure the environment variables. The configuration
procedures are as follows:
2. In the left area of the window, click Advanced system settings to open the
Advanced tab of System Properties dialog box.
Version: A 57
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
4. In the System variables list box, create and edit the environment variables
according to the following table. Then click OK.
Note:
58 Version: A
3 Installing the UNM2000
Prerequisite
u The communication between the server end and the client end is normal.
u The system firewall inbound/outbound rules have been set, or the system
firewall and anti-virus software have been disabled.
Procedure
Note:
The port number indicates the Tomcat port number set during the
installation of the server end.
2. Click Download client to download and save the client end installation
program.
Version: A 59
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
3. Double-click the client end installation program UNM2000_Zip and click Next
in the displayed dialog box.
60 Version: A
3 Installing the UNM2000
6. Specify the installation path of the UNM2000 client (the default installation path
D:\unm2000client is recommended), and then click Next.
Version: A 61
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
7. Enter the IP address of the server end, and then click Next.
62 Version: A
3 Installing the UNM2000
10. After the installation completes, double-click the client shortcut icon .
11. Click Yes in the Update confirmation alert box that appears to update the
client version.
Note:
You need to update the client version for the first login after installing the
client.
12. Wait till the update is completed. In the displayed Log into UNM2000 dialog
box, type the username and password (both are admin by default), and type
the IP address of the corresponding server in Server. Then click Login.
Note:
If the UNM2000 can be logged in successfully, the server end and the
client end are installed successfully.
Version: A 63
4 Upgrading the UNM2000
The following introduces how to upgrade the UNM2000. The UNM2000 supports
automatic upgrading of the client end. Upon startup, the client end will check for
updates and upgrade itself automatically, so as to synchronize the version of the
client end with that of the server end.
64 Version: A
4 Upgrading the UNM2000
The preparations for upgrading the server end of the UNM2000 include the following
aspects:
u The computer running the UNM2000 server end meets the system
configuration requirements described in System Configuration Requirements.
Prerequisite
To back up the configuration data to the FTP server, ensure that the FTP server can
be normally connected.
Procedure
You can also log into the UNM2000 client, and select System→UNM
Management Tool to access the login GUI of the UNM2000 network
management tool.
Version: A 65
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
2. Type the username and password (both are Admin by default) on the login GUI,
and click Login.
4. (Optional) Click set backup server button, set the relevant parameters and
click OK. Then, click OK in the alert box that appears.
5. Click export, type the file description and then click OK.
66 Version: A
4 Upgrading the UNM2000
When the UNM2000 cannot work normally, you can restore it to the latest version
using the backup software package.
Procedure
Note:
u If the D:\unm2000 install files directory does not exist, create it and
then back up the files.
u If the software package of the current version does not exist, back up
the current installation folder of the current UNM2000, for example,
D:\unm2000.
After completing the backup, you can uninstall the current UNM2000 according to
the following procedures.
Version: A 67
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Prerequisite
Procedure
You can uninstall the current version via the following three methods.
u Method 1:
4) In the displayed Question alert box, click Yes to uninstall the UNM2000.
6) In the displayed Question alert box, click Yes to restart the computer.
68 Version: A
4 Upgrading the UNM2000
u Method 2:
2) In the displayed Question alert box, click Yes to uninstall the UNM2000.
4) In the displayed Question alert box, click Yes to restart the computer.
Version: A 69
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
u Method 3:
2) In the displayed Question alert box, click Yes to uninstall the UNM2000.
4) In the displayed Question alert box, click Yes to restart the computer.
70 Version: A
4 Upgrading the UNM2000
Subsequent Operation
After uninstalling the UNM2000 and restarting the UNM2000 server, you need to
manually delete the unm2000 folder (D:\unm2000 by default) under the installation
directory of the original UNM2000 version.
Prerequisite
Procedure
2. Initialize the database table according to Initializing the Database Table and
then restart the computer.
After completing the upgrade of the UNM2000 version, you need to import the
configuration data.
Version: A 71
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Prerequisite
u If the configuration data are backed up on the FTP server, ensure that the FTP
server can be normally connected.
Procedure
You can also log into the UNM2000 client, and select System→UNM
Management Tool to access the login GUI of the UNM2000 network
management tool.
2. Type the username and password (both are Admin by default, case sensitive)
on the login GUI , and click Login.
3. Select all services on the process management GUI, click Stop, and then click
OK in the displayed alert box.
5. Click import, select the file to be imported, and then click OK.
72 Version: A
4 Upgrading the UNM2000
The tool running succeeds when the contents as shown below in the figure are
displayed.
Version: A 73
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
8. Click Process in the UNM2000 network management tool, select all services,
and click Start to start all the services.
The following introduces how to verify the upgrade of the server end.
Prerequisite
The Java cache of the original client should be cleared. Follow the steps below to
clear the Java cache.
2. In the Java Control Panel dialog box, click View next to Settings to display
the Java Cache Viewer dialog box.
74 Version: A
4 Upgrading the UNM2000
3. Select the application program and click to delete the Java cache.
Procedure
2. Click Yes in the Update confirmation alert box that appears to update the
client version.
3. Wait till the update is completed. In the displayed Log into UNM2000 dialog
box, type the username and password (both are admin by default), and type
the IP address of the corresponding server in Server. Then click Login.
Note:
Version: A 75
5 FAQ
The following introduces the FAQs in installing and uninstalling the UNM2000.
New Alarms Failed to Be Reported in Real Time / New ONU List Failed to Be
Refreshed
76 Version: A
5 FAQ
If errors occur during the installation / uninstallation, how to view the installation /
uninstallation logs?
Solution
Do as follows:
2. Open the install or uninstall file and view the recorded logs.
Solution
On the Windows OS, follow the steps below to view the Java version:
1. Select Start→Run, and type cmd in the Open text box of the dialog box that
appears, as shown below.
2. Click OK, and type java -version in the CLI window to view the version
information.
Version: A 77
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
On the SUSE Linux OS, follow the steps below to view the Java version:
1. Right-click the desktop and select Open in Terminal from the shortcut menu to
display the Terminal window.
Solution
Do as follows:
78 Version: A
5 FAQ
1) Select Start→Run, and type cmd in the Open text box of the dialog box
that appears, as shown below.
2) Click OK to display the CLI window and then run the following commands
to delete the MySQL service.
C:\Users\Administrator>d:
D:\>cd mysql\bin
D:\MySQL\bin>mysqld.exe-remove
Version: A 79
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
Solution
Do as follows:
1. Select Start→Run, and type cmd in the Open text box of the dialog box that
appears, as shown below.
2. Click OK to display the CLI window and then run the following commands to
delete the Tomcat service.
C:\Users\Administrator>d:
D:\>cd ApacheTomcat\bin
D:\ApacheTomcat\bin>service.bat remove
When The service ‘Tomcat6’ has been removed is displayed, the Tomcat
service has been deleted, as shown below.
80 Version: A
5 FAQ
Solution
Do as follows:
1. Select Start→Run, and type cmd in the Open text box of the dialog box that
appears, as shown below.
2. Click OK, and type netstat-nao in the CLI window to view the occupation of
system ports.
Version: A 81
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
The SNMP TRAP is not configured properly. As as result, the new alarms fail to be
reported in real time, or the new ONU list cannot be refreshed in a timely manner.
Solution
2. Check whether the Read the Community Name / Write the Community
Name (default value is adsl) has been configured in the SNMP Parameter
Template Management. Make sure this template has been bound with the
specified NE.
82 Version: A
5 FAQ
2) Select SNMP Trap Receiver IP, and add an entry. Set the IP Address to
the IP address of the server communicating with the device.
3) Select SNMP System Time Config, and set the NMS Server Address.
Note:
If the EMS server address is unknown, you can set the IP address to
0.0.0.0.
Version: A 83
UNM2000 Network Convergence Management System V2.0R4 Standalone System Installation Guide (Based on
Windows)
4) Select Time Calibration, and make sure that the time calibration is
successful.
84 Version: A
Appendix A Abbreviations
IP Internet Protocol
International Telecommunication Union-
ITU-T
Telecommunication Standardization Sector
NE Network Element
NEL Network Element Level
NML Network Management Layer
Version: A 85
Product Documentation Customer Satisfaction Survey
Thank you for reading and using the product documentation provided by FiberHome. Please take a moment to
complete this survey. Your answers will help us to improve the documentation and better suit your needs. Your
responses will be confidential and given serious consideration. The personal information requested is used for
no other purposes than to respond to your feedback.
Name
Phone Number
Email Address
Company
To help us better understand your needs, please focus your answers on a single documentation or a complete
documentation set.
Documentation Name
Code and Version
12. Additional comments about our documentation or suggestions on how we can improve:
Thank you for your assistance. Please fax or send the completed survey to us at the contact information
included in the documentation. If you have any questions or concerns about this survey please email at
[email protected]