ETNN SOUTHCO CAPEX PSC Pole 2017 PDF
ETNN SOUTHCO CAPEX PSC Pole 2017 PDF
TENDER SPECIFICATION FOR PROCUREMENT OF 8 MTR & 9 MTR LONG PSC POLES
(UNDER CAPEX PROGRAMME)
Issue of online tender documents (bid sheets):- From dt- 06.12.2017 (10.00 AM) up to 27.12.2017 (1.00 PM)
Page 1 of 47
SOUTHCO UTILITY
CORPORATE OFFICE: COURTPETA, BERHAMPUR, PIN-760004
DIST: GANJAM (ODISHA)
Email: procurement.southco@southcoodisha, Web: www.southcoodisha.com
For and on behalf of SOUTHCO UTILITY, sealed e-tenders are invited from the reputed manufacturers in two part
bidding system for supply of following items at the locations (Stores) as mentioned, under CAPEX Programme.
The interested bidders would be required to enroll themselves on the tender portal
www.tenderwizard.com/SOUTHCO. Complete set of bidding documents are available in www.tenderwizard.com
/SOUTHCO portal from Dt. 06.12.2017(10.00 AM) onwards (as per the e-tender schedule). Interested bidders may
visit SOUTHCO’s official web site www.southcoodisha.com or www.tenderwizard.com /SOUTHCO for detail
specification.
N.B : 1) Any addendum / corrigendum to this e-Tender Notice shall be uploaded in the website only.
2) Southco Utility reserves the right to accept / reject any or all bids without assigning any reasons
thereof.
The bidders can view the tender documents from www.southcoodisha.com website free of cost.
Page 2 of 47
(i) The bidders who want to submit bid shall have to pay the Rs. 11,200.00 towards tender cost (non-refundable
which is inclusive GST @ 12%), in the form of Demand draft only, drawn in favour of Administrator, SOUTHCO
Utility, payable at Berhampur.
NB: Cost of Tender shall be fully exempt for the local SSI Units located in the State of Odisha having valid
registration in D.I.C/NSIC on the date of submission of the tender. It is also applicable for Consortium of SSI Units.
(ii) The bidders shall have to submit the non-refundable tender processing fee as detailed below which is
inclusive of Goods & Service tax @18.0 % in the form of e-payment mode.
(NOTE: For tender processing fee to K.S.E.D.C. Ltd. Bangalore, the bidder can use various modes of e-payment
facility available through Tender wizard Portal, i.e. by Credit Card, Debit Card, Net Banking).
(iii)The bidders shall scan the Demand Draft / Bank guarantee, towards EMD and Tender Cost against the tender
and upload the same in the prescribed form in .pdf or .jpg format in addition to sending the original as stated
above.
(iv) The prospective bidders are advised to register their user ID, Password, company ID from website
www.tenderwizard.com/SOUTHCO by clicking on hyper link “Register Me”.
(v) Any clarifications regarding the scope of work and technical features can be had from the undersigned during
office hours.
NB: All subsequent addendum/Corrigendum to the tender shall be hoisted in SOUTHCO’s official web site
www.southcoodisha.com and www.tenderwizard.com/SOUTHCO only
For detail procedure to be followed for submission of Bid, please refer Clause No. 8 & 9
of ITB (page no.13 to 15)
Page 3 of 47
SOUTHCO UTILITY
CORPORATE OFFICE: COURTPETA, BERHAMPUR, PIN-760004
DIST: GANJAM (ODISHA)
Email: [email protected] / Website:www.southcoodisha.com
CONTENTS
VOLUME-I
VOLUME-II
SECTION –V : LIST OF ANNEXURES
*The annexures shall be read from Annexure I to VI in MS word along with Annexure VII to Annexure XIV
in MS excel format as per the heading specified .
*ANENXURE-XV:-PRICE BID
Page 4 of 47
VOLUME –I
Page 5 of 47
SECTION – I
Page 6 of 47
INVITATION FOR BIDS (IFB)
FOR SUPPLY OF 8 Mtr.& 9 Mtr. Long PSC Poles
(COMPETITIVE BIDDING)
E-TENDER NOTICE No. SOUTHCO UTILITY / CAPEX / PSC POLES / 21/2017-18
Date: 06.12.2017
SECTION –I
1.0 For and on behalf of the SOUTHCO UTILITY, the undersigned invites bids under two part bidding
system from the reputed manufacturers only for design, manufacture, supply, inspection,
loading at factory, transportation to & unloading at stores including guaranteed obligation for
supply of 8 Mtr. & 9 Mtr. long PSC poles under CAPEX Programme.
2.0 The Bidders are required to submit a detailed and comprehensive bid, consisting of Technical and
Commercial Proposal and conditions / schedule of non-compliance, if any. The submission of the
Bids shall be in the manner specified in the instruction to Bidders.
3.0 SOUTHCO UTILITY will not be responsible for any costs or expenses incurred by bidders in
connection with the preparation and delivery of bids.
3.1 SOUTHCO UTILITY reserves the right to cancel, postpone, withdraw the invitation for Bids without
assigning any reason thereof and shall bear no liability whatsoever consequent upon such a
decision if the situation so warrants.
4.0 E.M.D & TIME SCHEDULES:
SL. NO. DESCRIPTION SCHEDULE
Rs. 11,200/- (Rupees Eleven thousand Two hundred) only i.e. Rs 10000/-
+ GST @ 12%.
NOTE: Local SSI Units located in the state of Odisha having valid
registration in D.I.C/NSIC on the date of submission of the tender shall
be allowed to deposit 25% of the EMD amount as prescribed above. It
is also applicable for Consortium of SSI Units.
As mentioned in Tender Notice at page -3. (To be paid to K.S.E.D.C.Ltd,
Bangalore on e-payment mode.
3 Tender processing fee NOTE: For tender processing fee the bidder can use various modes of e-
payment facility available through Tender wizard Portal, i.e. by Credit
Card, Debit Card, Net Banking).
Page 7 of 47
4 Issue of bid document FROM : Dt. 06.12.2017 (10.00AM) upto 27.12.2017 (1.00 PM)
Last date of submission of
5
online tender Up to Dt. 27.12.2017 (5.00 PM)
Last date and time of
6
receipt of bid. (Hard Copy) Up to Dt. 28.12.2017 (1.00 PM)
Opening of Techno-
7
commercial bid (Part-I) ON Dt. 28.12.2017 after 04.00 PM
6.1.1. Technical:
a) The bidder should be a manufacturer of PSC poles for which he submits his offer. The bidder
must submit DIC/NSIC registration certificate or Factory License as a proof of manufacturer.
b) The bidder has to quote at least 50% of the tendered quantity (for any of the stores or all stores
under clause 5.0 above) of either or both of the materials covered under this notification. The
bidder should have supplied minimum 50% of the quoted/offered quantity during any one of the
financial year out of the immediate past three financial years. Bidders shall submit self attested
copies of P.O.’s (all pages), along with Tax Invoices, executed successfully for the relevant years
and abstract thereof in the enclosed format Annexure-XIV to prove the quantity as supplied.
c) The bid shall be accompanied by user’s certificate (preferably issued within immediate last 5
years) from any Distribution Utility/ Reputed Private Organization/ State Govt. / Central Govt. or
their undertaking(s) in support of satisfactory performance of their above materials supplied
earlier to them.
d) The offered material should have been factory tested. The bids shall be accompanied with the
drawings and factory test reports of the materials conducted within five years before the date of
opening of the Tender.
Page 8 of 47
e) The bidders who have earlier failed to execute the Purchase Order(s) of SOUTHCO UTILITY and /
or blacklisted by the SOUTHCO UTILITY/any of the distribution Utility shall not be eligible to
participate in this tender.
f) SOUTHCO UTILITY reserves the right to waive minor deviation, if they do not materially affect the
capacity of the bidder to perform the contract.
6.1.2 Financial:
The minimum average annual turnover of the intending bidder should not be less than two times
of the estimated cost of the quantity offered ( as given for 100% quantity in the table below) by
the bidder during best three financial years out of immediate past 5 financial years.
NB: Bidders offering for multiple stores must meet the sum of minimum turn over
requirements of the stores as indicated above. Accordingly bidders must furnish self attested
audited Annual Accounts of past 3 best financial years out of immediate past 5 financial years
to establish their Turnover requirement.
Two or more SSI Units having been manufacturer of tender item as per this tender
specification, may form a Consortium among themselves and apply against this specification,
provided they fulfill the following eligible criteria;
a) They should have legally valid consortium agreement as per the prescribed format for
the purpose of participation in the bidding process. The total no of a consortium shall
be limited to four members.
c) Consortium as a whole shall meet the qualifying norms specified in the tender, they
participate.
d) The lead member of the Consortium should meet at least 50% of the qualifying norms
in respect of the supply experience.
e) Besides the lead member, other member (s) of the Consortium should meet at least
15% of the qualifying norms in respect of the supply experience.
f) All the Consortium member(s) shall authorize the lead partner by submitting a power
of Attorney as per the prescribed format duly signed by the authorized signatories.
The lead partner shall be authorized to receive instructions for and on behalf of all
Page 9 of 47
partners of the Consortium and entire execution of the contract.
g) The Consortium and its members shall be jointly and severally responsible and be held
liable for the purpose of guaranteed obligation and any other matter as required
under the contract.
h) Any member of the Consortium member(s) shall not be eligible either in an individual
capacity or part of any other consortium to participate in the tender, where the said
consortium participates.
6.1.4. Documentation :
6.1.4.1. Bidder shall furnish self attested copies of original documents defining the constitution or legal
status, place of registration and principal place of business namely of Memorandum and Article
of Association.
6.1.4.3. Bidders shall submit self attested copy of their audited financial reports for best three financial
years out of last five years. In case the Bidder is in existence for less than 5 years the audited
financial report/s from the date of its incorporation should be furnished.
6.1.4.4 Self attested copies of Purchase order (all pages) successfully executed, & Users Performance
Certificate.
6.1.4.6 Self attested copy of GST registration certificate, copy of PAN Card.
6.1.4.7 Self attested copy of Income Tax Return of immediate past three years.
Notes: The bidder should present the original documents for verification as and when required
by SOUTHCO UTILITY.
7.0 All correspondence with regard to the above shall be made to the following address:
Page 10 of 47
SECTION –II
Page 11 of 47
SECTION –II
1. SOURCE OF FUNDS:
2. SCOPE OF WORK:
2.1 The scope of work in brief shall include design, manufacture, inspection, supply, loading at factory,
transportation to stores, unloading at stores including guaranteed obligation of complete supply of
materials in conformity to the technical specification enclosed herewith in Section – IV.
3. DISCLAIMER:
3.1 This Document includes statements, which reflect various assumptions, which may or may not be
correct. Each Bidder should conduct its own estimation and analysis and should check the
accuracy, reliability and completeness of the information in this Document and obtain
independent advice from appropriate sources in their own interest.
3.2 Neither Purchaser nor its employees will have any liability whatsoever to any Bidder or any other
person under the law or contract, the principles of restitution or unjust enrichment or otherwise
for any loss, expense or damage whatsoever which may arise from or be incurred or suffered in
connection with anything contained in this Document, any matter deemed to form part of this
Document, provision of Services and any other information supplied by or on behalf of Purchaser
or its employees, or otherwise arising in any way from the selection process for the Supply /
provision of Services for the Project.
3.3 Though adequate care has been taken while issuing the Bid document, the Bidder should satisfy
himself that documents are complete in all respects. Intimation of any discrepancy/ doubt shall be
sent to the Purchaser address for speedy response.
3.4 This document and the information contained herein are Strictly Confidential and are for use of
only the person (s) to whom it is issued/ downloaded from the website. It may not be copied or
distributed by the recipient to third parties (other than in confidence to the recipient’s
professional advisors).
4 COST OF BIDDING:
4.1 The Bidder shall bear all costs associated with the preparation and submission of its Bid and
SOUTHCO UTILITY will in no case be responsible or liable for those costs.
5. BIDDING DOCUMENTS:
5.1 The Scope of Work, Bidding Procedures and Contract Terms are described in the Bidding
Documents. In addition to the covering Letter accompanying Bidding Documents, the Bidding
documents include:
Page 12 of 47
(d) Technical Specification - Section –IV
(e) List of Annexure - Section –V
5.2 The Bidder is expected to examine the Bidding Documents, including all Instructions, Forms, Terms
and Specifications. Failure to furnish all information required in the Bidding documents or
submission of a Bid not substantially responsive to the Bidding Documents in every respect will /
may result in the rejection of the Bid.
6.1 At any time prior to the deadline for submission of Bids, the Purchaser may, for any reason,
whether at its own initiative or in response to a clarification requested by a prospective Bidder,
modify the Bidding Documents by way of issuing a corrigendum/addendum.
6.2 The corrigendum/ Addendum shall be part of the Bidding Documents, and it will be notified on the
website only. Interested bidders may visit SOUTHCO’s website www.southcoodisha.com or
www.tenderwizard.com/SOUTHCO for detail enquiry.
6.3 In order to afford prospective Bidders reasonable time in which to take the amendment into
account in preparing of their Bids, the Purchaser may, at its discretion, extend the deadline for the
submission of Bids.
7. LANGUAGE OF BID:
The Bid, prepared by the Bidder, and all correspondence and documents relating to the Bid
exchanged by the Bidder and the Purchaser, shall be written in the English Language. Any printed
literature furnished by the Bidder may be written in another Language, provided that the
literature is accompanied by an English translation, in which case, for purposes of interpretation of
the Bid, the English translation shall govern.
The bidder shall submit the bid in Electronic Mode only i.e. in
www.tenderwizard.com/SOUTHCO portal. The bidder must ensure that the bids are received in
the specified website of the SOUTHCO by the date and time indicated in the Tender notice.
8.3 The SOUTHCO UTILITY reserves the right to reject any bid, which is not submitted in electronic
mode and according to the instruction, stipulated above.
(i) For all the users it is mandatory to procure the Digital Signatures of Class III only.
(ii) Bidders / Suppliers are requested to follow the below steps for registration.
(i) Log in www.tenderwizard.com/SOUTHCO Click “Register”, fill the online registration Form.
Page 13 of 47
(ii) Payment for an amount of Rs. 2000/-+ 18% GST (Rs.2360/-) shall be made to KSEDCL,
Bangalore for vendor registration in tender wizard portal in e-payment mode only.
The bidders/suppliers who have already registered in e-tendering site of SOUTHCO UTILITY, they
need not to pay the registration amount to KSEDCL again for this tender.
(iii) As soon as the verification is being done the e-tender user id will be enabled/provided.
(i) Insert the PKI (which consist of your Digital Signature Certificate) in your System. (Note: Make
sure that necessary software of PKI be installed in your system).
(ii) Click / Double Click to open the Microsoft Internet Explorer (This icon will be located on the
Desktop of the computer).
(iv) Enter e-tender User Id and Password, click on “Go”. Click on “Click here to login” for selecting
the Digital Signature Certificate. Select the Certificate and enter DSC Password. Re-enter the e-
Procurement User Id Password
(vi) Click on Request icon for online request. After making the request, bidder has to pay the
requisite tender processing fee (as indicated in tender notice Page -3) through e-payment facility
only available in the portal. Bidders will receive the Tender Documents which can be checked and
downloaded by following the below steps.
(vii) Click to view the tender documents which are received by the user. Tender document screen
appears.
NOTE: For vendor registration and payment of tender processing fee to KESDCL, the bidder can
use various modes of e-payment facility available through Tender wizard Portal, i.e. by Credit
Card, Debit Card, Net Banking.
9.1 The bidder has to furnish the Tender cost, BID SECURITY (EMD) and a set of hard copy of
supporting documents uploaded in this tender except bid sheets (.xls) prior to last date and time
of receipt of bids as specified in tender Notice. Tender processing fees is mandatory & to be paid on
e-payment mode as stated elsewhere in the document.
Page 14 of 47
The bidder should fill up the Techno commercial and price schedule properly and fill in the bid
sheets provided in .xls format and up-load the same without changing the file name. The tender
may be rejected if the schedule of price is submitted in incomplete form.
NB: The bid sheets (.xls file) shall be uploaded in www.tenderwizard.com/SOUTHCO portal, prior
to online closing of the tender. By no other means (except online) price bid shall be accepted for
evaluation of tender.
(i) After completing all the formalities Bidders will have to submit the tender as specified NIT and
they must take care of all instructions. Prior to submission, verify whether all the required
documents have been attached and uploaded to the particular tender or not.
Note down / take a print of bid control number once it displayed on the screen
(ii) Tender Opening event can be viewed online.
(iii) Competitors bid sheets are available in the website for all participated bidders.
NOTES:
For any e-tendering assistant contact help desk number,
080- 40482000(Bangalore). SOUTHCO HELP DESK- 09937140591
10.1 Soft copy of the bid shall be uploaded through the portal
www.tenderwizard.com/SOUTHCO on or before the online submission time and date as
stipulated in the bidding document. DD towards Tender cost, DD/BG towards Bid Security & a
set of all required documents (except bid sheets in .xls format) must be received by SOUTHCO
UTILITY at the address specified not later than the time and date stated in the tender notification.
In the event of the specified date for the submission of bids being declared a holiday for
SOUTHCO UTILITY, the bids will be received on the next working day as per the time indicated in
tender notification.
10.2 SOUTHCO UTILITY may, at its discretion, extend this deadline for submission of bids by amending
the Bidding Documents in accordance with ITB for the reasons specified therein at any time prior
to opening of, in which case all rights and obligations of Employer and bidders will thereafter be
subject to the deadline as extended.
11.1 (i) Soft part of the bid will not be uploaded on the portal after expiry of submission time and the
bidder shall not be permitted to submit the same by any other mode. In such case, even if the
bidder has submitted the specific documents in hard copy in original (viz., bid security, tender
cost & any other document) within the stipulated deadline, its bid shall be considered as
late bid. The hard copy submitted [specific documents (viz., bid security, tender cost.)] shall be
returned unopened to the bidder.
(ii) Hard copy of the bid security of the bid received by SOUTHCO UTILITY after the deadline for
submission of bid prescribed by the GTCC will be considered as late bid even if the bidder has
uploaded the soft part of the bid within the stipulated deadline. In such a case, the soft part of
the bid uploaded on the portal shall be sent unopened to “Archive” and shall not be considered
at all any further.
Page 15 of 47
[
12.1 Bidder may modify or withdraw its bids through the relevant provisions on the portal
www.tenderwizard.com/SOUTHCO up to due date and time of submission of bid indicated in
tender notification.
a) Modified Electronic form of the bid as per the provision of portal therein.
b) Bidder may withdraw its bid through the relevant provisions of portal only.
12.3 No bid shall be modified/ withdrawn subsequent to the dead line for submission of bids.
Withdrawal/modification of bid before the expiry of bid validity shall result forfeiture of Bidder’s
bid security.
13.1 (A) Hard copy of the followings should be submitted with SOUTHCO UTILITY:
1. Tender Cost
2. Tender processing fee acknowledgement copy.
3. Bid Security (EMD) in shape of DD/BG as described.
4. DIC/NSIC/Factory license as a proof of manufacturer
5. Self attested copies of Purchase orders (All pages) as a proof of past supply experience.
6. Self attested copy of performance certificate.
7. Consortium Agreement & Power of Attorney.
8. PAN Card, GST registration certificate.
9. Audited annual accounts.
10. Bidder shall furnish self attested copies of original documents defining the constitution or
legal status, place of registration and principal place of business namely of Memorandum
& Article of Association.
11. Self attested copy of Power of Attorney/Board resolution (original) of the authorized
signatory of the bid.
12. Self attested copies of Purchase orders (all pages of the order) successfully executed, Users
Performance certificate, Type test report if any.
13. All uploaded file except price bid .The same shall be uploaded in www.Tenderwizard.com/
SOUTHCO portal only.
14.0 E.M.D:
14.1 The bidder shall submit E.M.D as a part of the bid in the prescribed manner for the amount
mentioned in Clause No.4 of Section –I.
Page 16 of 47
14.2 The E.M.D is required to protect the Purchaser against the risk of bidder’s conduct, which would
warrant the security’s forfeiture.
A/C payee demand draft in favour of “Administrator, SOUTHCO Utility” issued by a Schedule
bank payable at Berhampur.
OR
NB: In case of any deficiency such as the ownership of the security bond (other than the issuing
bank), deviation from the approved format, absence of signature of witness etc. found in the
EMD Bank Guarantee, the same shall be liable for rejection upfront. The bidder will not be given
any chance to rectify the same.
14.4 Unsuccessful bidder’s E.M.D shall be refunded back as promptly as possible, but not later than
thirty (30) days after the expiry of the period of bid validity. The successful bidder’s E.M.D shall be
discharged upon furnishing of the performance security.
1) If the bidder withdraws bid during the period of bid validity specified by the bidder in the bid
form.
2) In case the successful bidder fails to sign the contract in specified time and / or fails to submit
the requisite performance Bank guarantee.
3) In case of failure to supply the materials / equipment during the contractual delivery period.
15.1 Bidders have to quote for at least 50% quantity of either or both of the materials/equipment
covered under this specification for any or all Stores strictly as per the enclosed .xls format given
store wise. The total Bid Price shall also cover all the Supplier’s obligations mentioned in or
reasonably to be inferred from the Bidding Documents in respect of Design, Supply, testing,
inspection, loading at factory, Transportation to stores and unloading at stores all in accordance
with the requirement of Tender Documents. The Bidder shall complete the appropriate Price
Schedules enclosed in .xls format store wise stating the Unit Price for each item, freight &
insurance separately & applicable GST thereon and thereby arriving at the total amount.
15.2 In case there is any increase in the number of units as compared to those mentioned in the IFB,
the Contract Price shall be subject to increase proportionately on pro-rata basis.
15.3 The Price offered shall be inclusive of all costs as well as applicable GST thereon payable during
implementation of the contract.
15.4 Prices quoted by the Bidder shall be “Firm” and not subject to any price adjustment during the
performance of the Contract. A Bid submitted with variable Price or an adjustable price clause
shall be treated as non-responsive and rejected out rightly.
16.1 The Ex-Works Prices & transportation charges quoted for the Contract shall remain FIRM as per
the above Parameters and Purchaser shall not compensate Bidder for any variations. However any
Page 17 of 47
variation in the taxes within the schedule date of delivery shall be borne by the Purchaser, else the
same shall be borne by the bidder.
16.2 In case the Purchaser, revise the scope of woks, bidders shall be compensated based on the Unit
Rate (Ex-Works) agreed upon before Order placement or as per mutually acceptable rates.
18.1 Bids shall remain valid for 180 days from the date of opening of commercial Bids.
18.2 Notwithstanding Clause 18.1 above, the Purchaser may solicit the Bidder’s consent to an
extension of the Period of Bid Validity. The request and the responses thereto shall be made in
writing or by email.
19.1 Bidders shall submit Bids, which comply with the Tender Documents. Alternative bids shall not be
considered for evaluation.
20.1 Each Bidder shall submit only one Bid either by himself, or as a partner in a Joint
Venture/Consortium. A Bidder who submits or participates in more than one Bid for the same
item, either individually or jointly, will cause all those Bids to be rejected out rightly.
Information relating to the examination, clarification, evaluation and comparison of Bids and
recommendations for the award of a contract shall not be disclosed to Bidders or any other
persons not officially concerned with such process. Any effort by a Bidder to influence the
Purchaser’s processing of Bids or award decisions may result in the rejection of the Bidder’s Bid.
To assist in the examination, evaluation and comparison of Bids, the Purchaser may, at its
discretion, ask the Bidder for a clarification of its Bid. All responses to requests for clarification
shall be in writing and no change in the price or substance of the Bid shall be sought, offered or
permitted.
23.1 Purchaser will examine the Bids to determine whether they are complete, whether any
computational error have been made , whether required sureties have been furnished, whether
the documents have been properly signed, and whether the Bids are generally in order.
23.2 Arithmetical errors will be rectified on the following basis. If there is a discrepancy between the
unit price and the total price per item that is obtained by multiplying the unit price and quantity,
the unit price shall prevail and the total price per item will be corrected. If there is a discrepancy
between the total amount and the sum of the total price per item, the sum of the total price per
item shall prevail and the Total Amount will be corrected.
Page 18 of 47
23.3 Prior to the detailed evaluation, pursuant to Clause 25, the Purchaser will determine the
substantial responsiveness of each Bid to the Bidding Documents including production capability
and acceptable quality of the materials offered, pursuant to Clause 13. Substantially responsive
Bid is one, which conforms to all the terms and conditions of the Bidding Documents without
material deviation.
23.4 A Bid determined as not substantially responsive will be rejected by the Purchaser and will not
subsequently allowed to be made responsive by the Bidder by correction of the non – conformity.
24.1 The evaluation of Bids shall be done basing on the delivered cost competitiveness basis for each
store separately.
24.2 The evaluation of the Bids shall be a stage-wise procedure. The following stages are identified for
evaluation purposes:
In the first stage, the Bids would be subjected to a responsiveness check as detailed in the clause
23. The Technical Proposals and the Commercial terms & conditions of the Bidders would be
evaluated and discussed as per clause 6.0 of this document.
Subsequently, the Financial Proposals along with Supplementary Financial Proposals, if any, of
Bidders with Techno-commercially Acceptable Bids submitted prior to final evaluation shall be
considered.
24.3 The Purchaser’s evaluation of a Bid will take into account, in addition to the Bid price, the
following factors, in the manner and to the extent indicated in this Clause:
a) Delivery Schedule:
b) Deviations from Bidding Documents as mentioned in Non-Compliance Schedule.
c) Past performance and capability to execute the contract.
d) Drawings and factory test reports of the materials.
e) Audited annual Accounts.
Bidders shall base their Bid price on the terms and conditions specified in the Bidding Documents.
The Cost of all quantifiable deviations and omissions from the specification, terms and conditions,
specified in Bidding Documents shall be evaluated. The Purchaser will make his own assessment of
the cost of any deviation for the purpose of ensuring fair comparison of Bids.
In normal circumstances the Purchaser will generally award the Contract to the successful Bidder
whose Bid has been determined to be the lowest evaluated responsive Bid, provided further that
the Bidder has been determined to be qualified to perform the Contract satisfactorily. If the lowest
evaluated price (L1) of more than one responsive bidder(s) is same, then in such event the tender
quantity shall be awarded in equal proportion.
However, for timely completion of the project, the purchaser may distribute the order among the
bidders (maximum three) at L1 rate. In case of distributing between two bidders, the ratio shall be
70% (L1): 30% (L2) or the quantity offered/quoted by the bidders whichever is less. Similarly in
case of distributing among 3 bidders, the ratio shall be 50% (L1):30% (L2):20% (L3).
In case L2 & L3 bidders does not agree to match the L1 prices, negotiation can be held with other
techno-commercially responsive L4, L5 …….bidders in sequence to match L1 price (Landed cost).
Page 19 of 47
26.0 CONTACTING THE PURCHASER:
26.1 From the time between Bid opening to award of contract, if any Bidder wishes to contact the
Purchaser on any matter related to the Bid, he should do so in writing.
26.2 Any effort by a Bidder to influence the Purchaser and / or in the Purchaser’s decisions in respect of
Bid evaluation, Bid comparison or Contract of Award, will result in the rejection of the Bidder’s Bid.
27.0 THE PURCHASER’S RIGHT TO ACCEPT ANY BID AND TO REJECT ANY OR ALL BIDS OR TO RELAX
ANY TERMS AND CONDITIONS:
27.1 The Purchaser reserves the right to accept or reject any Bid and to annul the Bidding process and
reject all Bids at any time prior to award of Contract, without thereby incurring any liability to the
affected Bidder or Bidders or any obligation to inform the affected Bidder or Bidders regarding the
grounds for the Purchaser’s action.
27.2 In the interest of work, the Purchaser reserves the right to relax any terms and conditions without
affecting the quality & price of the equipments.
27.3 The Purchaser will award the Contract to the successful Bidder whose Bid has been determined to
be the lowest- evaluated responsive Bid, provided further that the Bidder has been determined to
be qualified to perform the Contract satisfactorily. The Purchaser at its option/ discretion may split
the total quantity to be supplied between two or more Techno- Commercially responsive Bidders
in case of the bid prices are same and early delivery is required by the purchaser.
The Purchaser reserves the right to vary the quantity i.e. increase or decrease the number of
materials without any change in unit price, terms and conditions at the time of placing the orders
or during the execution of the Contract.
29.1 The letter of intent / Notification of Award shall be issued to the successful Bidder(s) whose bid(s)
have been considered responsive, techno-commercially acceptable and evaluated to be the
Lowest (L1). The successful Bidder shall be required to furnish a letter of acceptance to it within 7
days of issue of the letter of intent / Notification of Award by Purchaser.
30.1 Within 10 days of the receipt of Notification of Award / Letter of Intent from the Purchaser, the
successful Bidder shall furnish the Performance Security in the form of Bank Guarantee executed
on non-judicial stamp paper worth Rs.100/- (Rupees One hundred only) issued by a scheduled
Bank in favour of the Administrator, SOUTHCO Utility encashable at Berhampur only for an
amount of 10% (ten percent) of the Contract Price in accordance with the General Conditions of
Contract in the Performance Security Form provided in Section –V of Bidding Documents. The
Bank Guarantee shall be valid for a period not less than 90 days over and above the guarantee
period.
31.1 The Purchaser requires that the Bidders observe the highest standard of ethics during the
procurement and execution of the Project. In pursuance of this policy, the Purchaser:
Page 20 of 47
a) Defines, for the purposes of this provision, the terms set forth below as follows:
(i) “Corrupt practice” means behavior on the part of officials in the public or private sectors
by which they improperly and unlawfully enrich themselves and/ or those close to them,
or induce others to do so, by misusing the position in which they are placed, and it
includes the offering, giving, receiving, or soliciting of anything of value to influence the
action of any such official in the procurement process or in contract execution; and
b) Purchaser will reject a proposal for award if it determines that the Bidder recommended for award
has engaged in corrupt or fraudulent practice in competing for the contract in question.
c) Purchaser will declare a firm ineligible, either indefinitely or for a stated period of time, to be
awarded an contract if he at any time determines that the firm is engaged in corrupt or fraudulent
practice in competing for, or in executing, the Contract.
31.2 Furthermore, Bidders shall be aware of the provision stated in the General Terms and Conditions
of Contract.
The Bidder should provide accurate information on any litigation or arbitration resulting on
contracts completed or under execution by him over the last three (3) years. A consistent history
of awards involving litigation against the Bidder may result in disqualification of Bid.
Page 21 of 47
SECTION –III
Page 22 of 47
SECTION – III
GENERAL TRMS AND CONDITIONS OF CONTRACT (GTCC)
1.01 All the Bids shall be prepared and submitted in accordance with these instructions.
1.02 Bidder shall bear all costs associated with the preparation and delivery of its Bid, and the
Purchaser will in no case shall be responsible or liable for these costs.
1.03 The Bid should be submitted by the Bidder in whose name the bid document has been issued
and under no circumstances it shall be transferred / sold to the other party.
1.04 The Purchaser reserves the right to request for any additional information and also reserves the
right to reject the proposal of any Bidder, if in the opinion of the Purchaser, the data in support
of Tender requirement is incomplete.
1.05 The Bidder is expected to examine all instructions, forms, terms & conditions and specifications
in the Bid Documents. Failure to furnish all information required in the Bid Documents or
Submission of a Bid not substantially responsive to the Bid Documents in every respect may
result in rejection of the Bid. However, the Purchaser’s decision in regard to the responsiveness
and rejection of bids shall be final and binding without any obligation, financial or otherwise, on
the Purchaser.
2.01 SOUTHCO Utility shall mean the “Purchaser” on whose behalf this bid enquiry is issued by its
authorized representative / officers.
2.02 “Bidder” shall mean the firm who quotes against this bid document issued by the Purchaser.
“Contractor / Seller” shall mean the successful Bidder(s) whose bid has been accepted by the
Purchaser and shall include his heirs, legal representatives, successors and permitted assigns.
2.03 “Site” shall mean the Electricity Distribution Area of the Purchaser.
2.04 “Specification” shall mean collectively all the terms and stipulations contained in those portions
of this bid document known as Instruction to Bidder, Bid form and other forms as per Section –
V, General Conditions of Contract, Specifications and the Amendments, Revisions, Deletions or
Additions, as may be made by the Purchaser from time to time.
2.05 “Letter of Intent” shall mean the official notice issued by the Purchaser notifying the Contractor
that his proposal has been accepted and it shall include amendments thereto, if any, issued by
the Purchaser. The “Letter of Intent” issued by the Purchaser shall be binding on the
“Contractor”. The date of detailed Purchase Order shall be taken as the effective date of the
commencement of contract.
2.06 “Month” shall mean the calendar month and “Day” shall mean the calendar day.
2.07 “Codes and Standards” shall mean all the applicable codes and standards as indicated in the
Technical Specification.
2.08 “Offer Sheet” shall mean Bidder’s firm offer submitted to Purchaser in accordance with the
specification.
Page 23 of 47
2.09 “Contract” shall mean the “Detailed Purchase Order” issued by the Purchaser.
2.10 “Contract Price” shall mean the Price referred to in the “Detailed Purchase Order”.
2.11 “Contract Period” shall mean the period during which the “Contract” shall be executed as agreed
between the Contractor and the Purchaser in the Contract inclusive of extended contract period
for reasons beyond the control of the Contractor and / or Purchaser due to force majeure.
2.12 “Goods/Materials” shall mean all items to be supplied under Purchase Order whether raw
materials, processes materials, equipment, fabricated Materials, drawings or other documents
etc. as applicable.
2.13 “Store” shall mean any store under the jurisdiction of SOUTHCO Utility.
2.14 “Project / Unit” shall mean supply of Materials as per enclosed technical specification.
3.02 Priority: Should there be any discrepancy between any terms hereto and any term of the offer
sheet, the terms of this tender document shall prevail.
4.03 All relevant drawings, data and instruction manuals and other necessary inputs shall be under
the scope of contract.
6.0 The seller shall be responsible & shall comply with the provisions of all statutory acts i.e
Electricity Act 2003, Indian Electricity Rules 1956, Income Tax Act-1961 etc.
ii) The Contractor shall give to the Purchaser adequate time/ notice (minimum of two
weeks’ time) in writing for inspection of materials indicating the place at which the
equipment is ready for testing and inspection and shall also furnish the Routine Test
Page 24 of 47
Certificates and Packing List along with offer for inspection to the Purchaser indicating
the quantity which can be delivered in full truck load / Mini truck load to facilitate issue
of dispatch instruction.
iii) Where the contract provides for test on the Premises of the Contractor or of any of his
Sub-Contractors, the Contractor shall provide such assistance, labour, materials,
electricity, fuel and instruments as may be required or as may be reasonably demanded
by the Purchaser’s representative to carry out such tests efficiently. The Contractor is
required to produce Shop Routine Test Certificates before offering their materials for
inspection.
iv) After completion of the tests as indicated above, the Purchaser’s representative shall
forward the test results to the Purchaser. If the test results confirm to the specific
standard, the Purchaser shall approve the test results and communicate the same to the
Contractor in writing. The Contractor shall provide at least three copies of the test
certificates to the Purchaser.
v) The Purchaser has the right to have the test carried out at his own cost by an
independent agency whenever there is a dispute regarding the quality of supply.
vi) The Purchaser at its discretion may re-test the Materials/Equipment at its own
laboratory or laboratory of his choice for reconfirmation of the test results.
vii) Besides the above, the Third Party Independent Evaluation Agency (TPIEA) engaged by
GRIDCO shall have right to conduct the pre dispatch inspection (as explained above)
of the equipment/material procured by the Purchaser jointly along with the
representative of purchaser/independently by the TPIEA as the case may be.
b) Terminate the contract for balance work / supplies with enforcement of penalty Clause as per
contract for the un-delivered materials and with forfeiture of Performance Guarantee/
Composite Bank Guarantee.
c) Acquire the defective equipment / materials at reduced price considered equitable under the
circumstances.
10.1 The bidder(s) should furnish information regarding experience particularly on the following
points :
Page 25 of 47
i) Name of the manufacturer :
ii) Standing of the firm for manufacture of equipment/material quoted :
iii) Description of materials/equipment supplied during the last 3 (three) years with the
name (s) of the party (s) to whom supplies were made.
iv) Testing facilities at manufacturer’s work with copies of calibrated certificates of the
major testing equipment.
v) If the manufacturer is having collaboration with other firm(s), details regarding the
same:
vi) A list of Purchase orders, executed during the last three years along with user’s
certificate and copies of Purchase orders.
10.2 Bids may not be considered if the past manufacturing experience is found to be un-satisfactory
as mentioned under clause -6 of the IFB
It is in the interest of the Bidders to study the Specification, drawing etc. specified in the tender
document thoroughly before tendering so that, if any deviations are made by the Bidders, the
same are prominently brought out on a separate sheet in the Technical & Commercial Deviation
Formats enclosed at Annexure XII & XIII in this document. Deviation mentioned in any other
format or any other part of the offer document shall not be considered as a deviation & in such
case it will be presumed that the bidder has accepted all the conditions, stipulated in the tender
Specification, notwithstanding any exemptions mentioned therein.
The above Prices shall also include loading at factory site & unloading at Purchaser’s stores.
Price evaluation will be based on total landing cost, taking into accounts the applicable GST.
100 % value of each consignment (including transportation charges) will be paid within 30 days
of receipt of materials in good conditions at stores and verification there of subject to approval
of the Guarantee certificates & Test Certificates and submission & acceptance of Performance
Bank Guarantee equivalent to 10 % of Total Contract Price on non-judicial stamp paper worth
Rs.100 in the prescribed format from a scheduled Bank encashable at Berhampur only.
Or else an equivalent amount of 10 % of the Total Contract Price shall be deducted from the
invoice of the first consignment & the same shall be refunded after submission and approval of
the required Performance Bank Guarantee or expiry of Guarantee Period whichever is earlier.
Page 26 of 47
15.0 PRICE VALIDITY:
15.01 All bids submitted shall remain valid, firm and subject to unconditional acceptance by Purchaser
for 180 days post bid date. For award of Contract, the prices shall remain valid and firm till
contract completion.
16.0 GUARANTEE:
16.01 The bidder shall guarantee for satisfactory performance of the equipments/materials for a
minimum period of 24 months from the date of receipt of last consignment. In the event of any
defect in the equipment/ materials arising out of faulty design, inferior quality of raw material
used or bad workmanship within the guarantee period, the Seller shall guarantee to replace/
repair to the satisfaction of the Purchaser the defective equipments free of cost. Should
however, the manufacturer fails to do so within a reasonable time, the Purchaser reserves the
right to recover the amount from the seller either from the bills pending or may recover from
the Performance Guarantee submitted by the firm. Seller shall give a Performance Bank
Guarantee in favour of the Administrator, Southco Utility for 10% of the order value valid for
90 days over and above the guarantee obligation.
16.02 If during the defect liability period any services performed found to be defective, these shall be
promptly rectified by seller at its own cost (including the cost of dismantling and reinstallation)
on the instruction of Purchaser.
17.0 RELEASE:
The seller’s Performance Bank Guarantees / Assignable Bank Guarantee will be released without
interest within thirty (30) days from the last date up to which the Performance Bank Guarantee
has to be kept valid (as defined in Clause 16.01).
The Purchaser and the Contractor, to the extent of their respective rights permitting to do so,
shall exchange such technical information and data as is reasonably required by each party to
perform its obligations and responsibilities. The Purchaser and the Contractor agree to keep
each other in confidence and to use the same degree of care as he uses with respect to his own
proprietary data to prevent its disclosure to third parties of all technical and confidential
information. The technical information, drawings, records and other document shall not be
copied, transferred, traced or divulged and / or disclosed to third party in full / part nor misused
in any other form. This technical information, drawing etc. shall be returned to the Purchaser
with all approved copies and duplicates. In the event of any breach of this Contract, the
Contractor shall indemnify the Purchaser against any loss, cost of damages of claim by any party
in respect of such breach.
19.01 The date of the issue of the detailed Purchase Order shall be treated as the effective date of the
commencement of Contract.
20.0 The bidder shall quote the basic price as well as applicable GST as per the enclosed format for
bid prices.
21.0 PENALTY:
21.01 If supply of materials / equipments is delayed beyond the supply schedule as stipulated in
Purchase order, then the seller shall be liable to pay to the Purchaser as penalty for delay, a sum
of 0.5% (half percent) of the contract price for every week delay or part thereof.
Page 27 of 47
21.02 The total amount of penalty for delay under the contract will be subject to a maximum of five
percent (5%) of the contract price.
21.03 The Purchaser may, without prejudice to any method of recovery, deduct the amount for such
damages from any amount due or which may become due to the seller or from the Performance
Bank Guarantee or file a claim against the seller.
The Order is valid for 10 weeks beyond the schedule date of delivery, unless otherwise extended
by the Competent Authority. The Order shall stand cancelled automatically beyond the validity
period without any correspondences and liabilities to the purchaser.
23. PACKING :
The materials / equipments shall be packed by the seller suitably as per the standard procedure
for safe transport to the store. The cases shall be clearly marked showing distinctly the name
and address of the consignee. In case of special instructions, such as “this end up”, “fragile”,
“handle with care” etc., the same shall be clearly displayed on the cases.
The seller shall replace, free of cost, any spares which may be found defective by the buyer
during commissioning.
25.1 Any dispute arising out of this contract shall be referred to the AO, SOUTHCO/CMD, GRIDCO
who shall decide the case as sole arbitrator
25.2 For the purpose of dispute resolution, this agreement shall be governed by the provision of
Arbitration & Conciliation Act, 1996.
25.3 All disputes shall be subject to exclusive jurisdiction of the Court at Bhubaneswar and Writ
jurisdiction of Hon’ble High Court of Odisha at Cuttack.
26.1 Events of Default. Each of the following events or occurrences shall constitute an event of
default (“Event of Default”) under the Contract :
(a) Seller fails or refuses to pay any amount due under the Contracts.
(b) Seller fails or refuses to deliver Commodities conforming to his Bid document/ specifications,
or fails to deliver Commodities and, or execute the works assigned to them within the period
specified in P.O or any extension thereof.
(c) Seller becomes insolvent or unable to pay its debts when due, or commits any act of
bankruptcy, such as filing any petition in any bankruptcy, winding-up or reorganization
proceeding, or acknowledges in writing its insolvency or inability to pay its debts; or the Seller’s
creditors file any petition relating to bankruptcy of Seller;
(d) Seller otherwise fails or refuses to perform or observe any term or condition of the Contract
and such failure is not remediable or, if remediable, continues for a period of 30 days after
Page 28 of 47
receipt by the Seller of notice of such failure from Purchaser.
(a) If an Event of Default occurs and would be continuing, Purchaser may forthwith terminate
the Contract by written notice.
In the Event of Default, Purchaser may, without prejudice to any other right granted to it by
law, or the Contract, take any or all of the following actions;
i) present for payment, to the relevant bank the Contract Performance Bank Guarantee;
Recover any losses and / or additional expenses, Purchaser may incur as a result of
ii) Seller’s default.
28.01 The term “Force Majeure” as employed herein include, acts of God or force of nature, landslide,
earthquake, flood, fire, lightning, explosion, major storm (hurricane, typhoon, cyclone etc. ) or
major storm warning, tidal wave, shipwreck and perils of navigation, act of war (declared or
undeclared ) or public enemy, strike (excluding employee strikes, lockouts or other industrial
disputes or action solely among employee of Contractor or its subcontractors ) act or omission
of Sovereign States or those purporting to represent Sovereign States, blockade, embargo,
quarantine, public disorder, sabotage, accident or similar events beyond the control of the
parties or either of them.
5. Non-conformance by Sub-Seller.
Unless the delay arises out of a Force Majeure occurrence and is beyond both Seller’s and Sub-
Seller’s or Seller’s control and an alternate acceptable source of services, equipment or material
is unavailable. Additionally, Force Majeure shall not include financial distress of Seller or any
Sub-Seller.
28.02 In the event of either party being rendered unable by Force Majeure to perform any obligation
required to be performed by them under the Contract, the relative obligation of the party
affected by such Force Majeure shall be suspended for the period during which such cause lasts.
Time for performance of the relative obligation suspended by Force Majeure shall then stand
extended by the period for which the cause lasts.
Page 29 of 47
28.03 Upon the occurrence of any Force Majeure event, the party so affected in the discharge of its
obligation shall promptly, but no later than seven (7) days give written notice of such even to the
other party. The affected party shall make every reasonable effort to remove or remedy the
cause of such Force majeure or mitigate its effect as quickly as possible. If such occurrence
results in the suspension of all or part of the work for a continuous period of more than 10(ten)
days, the parties shall meet and determine the measures to be taken.
28.04 Any delay or failure in performance by either party hereto shall not give rise to any claims for
damages or loss of anticipated profits if and to the extent, such delay or failure is caused by
Force Majeure.
29.1 All the equipments and materials supplied under CAPEX programme shall bear distinct mark of
“Name of the Purchaser, GoO, CAPEX Programme, PO Order No. & Date, Guarantee Period” by a
way of embossing / punching / Engraving/casting etc. This should be clearly visible to naked eye.
30 INDEMNIFY
30.1 The Vendor, its successor and assignee shall indemnify the Purchaser, its successor and assignee
from all current & future liabilities that may arise out of purchase contract(s) entered into
between the vendor & the Purchaser.
Page 30 of 47
SECTION –IV
TECHINICAL SPECIFICATIONS
FOR
Page 31 of 47
TECHNICAL SPECIFICATION OF 8MTR 200KG PSC POLE & 9MTR 300KG PSC POLE
I. Applicable Standard:
II. Materials:
Cement
Cement to be used in the manufacture of pre-stressed concrete poles shall be ordinary for rapid
hardening Portland cement confirming to IS: 269-1976 (Specification for ordinary and low heat Portland
cement) or IS: 8041 E-1978 (Specification for rapid hardening Portland cement).
Aggregates
Aggregates to be used for the manufacture of pre-stressed concrete poles shall confirm to IS: 383
(Specification for coarse and fine aggregates from natural sources for concrete) .The nominal
maximum sizes of aggregates shall in no case exceed 12 mm for 8mtr pole and 10mm for 9mtr pole.
Water
Water should be free from chlorides, sulphates, other salts and organic matter. Potable water will be
generally suitable.
Admixture
Admixture should not contain Calcium Chloride or other chlorides and salts which are likely to promote
corrosion of pre-stressing steel. The admixture shall conform to IS: 9103.
Pres-Stressing Steel
Pre-stressing steel wires including those used as un tensioned wires should conform to IS:1785 (Part-I)
(Specification for plain hard-drawn steel wire for pre-stressed concrete, Part-I cold drawn stress
relieved wire).IS:1785 (Part-II)(Specification for plain hard-drawn steel wire) or IS:6003 (Specification for
indented wire for pre-stressed concrete).The type design given in the annexure are for plain wires of 4
mm diameter with a guaranteed ultimate strength of 175kg/mm². All pre-stressing steel shall be free
from splits, harmful scratches, surface flaw, rough, aged and imperfect edges and other defects likely to
impair its use in pre-stressed concrete.
Concrete Mix
Concrete mix shall be designed to the requirements laid down for controlled concrete (also called
design mix concrete) in IS: 1343-1980 (Code of practice for pre-stressed concrete) and IS: 456 – 1978
(Code of practice for plain and reinforced concrete) subject to the following special conditions:
Minimum works cube strength at 28 days should be at least 420Kg/cm² for
8mtr pole and 400Kg/cm² for 9mtr pole. The concrete strength at transfer
should be at least 210 Kg/cm² for 8mtr pole and 200Kg/cm² for 9mtr pole.
The mix should contain at least 380 Kg of cement per cubic meter of concrete.
The mix should contain as low water content as is consistent with adequate workability. It becomes
necessary to add water to increase the workability the cement content also should be raised in such a
way that the original value of water cement ratio is maintained.
Page 32 of 47
The poles shall be designed for the following requirements:
The poles shall be planted directly in the ground with a planting depth as per IS: 1678. Wherever,
planting depth is required to be increased beyond the specified limits or alternative arrangements are
required to be made on account of ground conditions e.g. water logging etc., the same shall be in the
scope of the bidder at no extra cost to owner. The bidder shall furnish necessary design
calculations/details of alternative arrangements in this regard.
The working load on the poles should correspond to those that are likely to come on the pole during
their service life.
The factor of safety for 9.0Mts pole Shall not be less than 2.0 and for 8.0 M poles, the factor of
safety shall not be less than 2.5. The average permanent load shall be 40% of the working load. The F.O.S.
against first load shall be 1.0. At average permanent load, permissible tensile stress in concrete shall be
30 kg/cm². At the design value of first crack load, the modulus of rupture shall not exceed 53.0kg/cm²
for M-400 concrete of 9mtr pole and 55.2Kg/cm² for M-420 Concrete of 8mtr pole.
The ultimate moment capacity in the longitudinal direction should be at least one fourth of that in the
transverse direction.
The maximum compressive stress in concrete at the time of transfer of pre-stress should not exceed
0.8 times the cube strength.
The concrete strength at transfer shall not be less than half, the 28 days strength ensured in the design,
i.e. 420x0.5=210kg/cm² for 8mtr pole and 400x0.5=200Kg/cm² for 9mtr pole. For model check
calculations on the design of poles, referred to in the annexure, a reference may be made to the REC
“ Manual on Manufacturing of solid PCC poles, Part-I-Design Aspects”.
All pre-stressing wires and reinforcements shall be accurately fixed as shown in drawings and
maintained in position during manufacture. The un-tensioned reinforcement as indicated in the
drawings should be held in position by the use of stirrups which should go round all the wires.
All wires shall be accurately stretched with uniform pre-stressed in each wire. Each wire or group of
wires shall be anchored positively during casing. Care should be taken to see that the anchorages do
not yield before the concrete attains the necessary strength.
V. Cover
The cover of concrete measured from the outside of pre-stressing tendon shall be normally 20 mm.
VII. Compacting
Concrete shall be compacted by spinning, vibrating, shocking or other suitable mechanical means.
Hand compacting shall not be permitted.
VIII. Curing
The concrete shall be covered with a layer of sacking, canvass, Hessian or similar absorbent material
and kept constantly wet up to the time when the strength of concrete is at least equal to the minimum
Page 33 of 47
strength of concrete at transfer of pre-stress. Thereafter, the pole may be removed from the mould and
watered at intervals to prevent surface cracking of the unit the interval should depend on the
atmospheric humidity and temperature. The pre-stressing wires shall be de-tensioned only after the
concrete has attained the specified strength at transfer (i.e. 200 or 210 kg/cm² as applicable).The cubes
cast for the purpose of determining the strength at transfer should be coursed, a sear as possible, under
condition similar to those under which the poles are cured. The transfer stage shall be determined
based on the daily tests carried out on concrete cubes till the specified strength indicated above is
reached. Thereafter the test on concrete shall be carried out as detailed in IS: 1343(code of practice for
pre-stressed concrete). The manufacture shall supply, when required by the owner or his
representative, result of compressive test conducted in accordance with IS: 456 (Code of practice for
plain and reinforced concrete) on concrete cubes made from the concrete used for the poles. If the
manufacture so desired, the manufacture shall supply cubes for test purpose and such cubes shall be
tested in accordance with IS: 456 (Code of practice for plain and reinforced concrete).
XII. Earthing
(a) Earthing shall be provided by having length of 8 SWG GI wire embedded in Concrete during
manufacture and the ends of the wires left projecting from the pole to a length of 50mm at 250
mm from top and 150 mm below ground level for 8mtr pole. Similarly, the end of the wires left
projecting from the pole to a length of 100mm at 250mm from top and 150 mm below ground level
for 9mtr pole.
(b) Earth wire shall not be allowed to come in contract with the pre-stressing wires
Page 34 of 47
SECTION –V
LIST OF ANNEXURES
Page 35 of 47
Annexure – I
DECLARATION FORM
To,
Sir,
Having examined the above specifications together with the Tender terms and conditions referred to therein.
1- I / we the undersigned do hereby offer to supply the materials covered thereon in complete shape in all
respects as per the rules entered in the attached contract schedule of prices in the tender.
2- I / we do hereby undertake to have the materials delivered within the time specified in the tender.
3- I / we do hereby guarantee the technical particulars given in the tender supported with necessary reports
from concerned authorities.
4- I / we do hereby certify to have furnished a copy of the tender specifications by remitting Cash/ Demand
draft & this has been duly acknowledged by you in your letter No……………..Dt……………….
5- I / we do hereby agree to furnish the composite Bank Guarantee in the manner specified / acceptable by
SOUTHCO UTILITY & for the sum as applicable to me / us within Ten days of issue of Letter of intent /
Purchase Order, in the event of Purchase order being decided in my / us favour , failing which I / we clearly
understand that the said LOI / P.O. shall be liable to be withdrawn by the Purchaser
(This form should be duly filled up & signed by the bidder & submitted along with the original copy of the bid)
Page 36 of 47
ANNEXURE-II
1. I / we, the undersigned do hereby declare that, I / we have never ever been blacklisted and /
or there were no debarring actions against us for any default in supply of material /
equipments or in the performance of the contract entrusted to us in any of the Electricity
Utilities of India.
2. In the event of any such information pertaining to the aforesaid matter found at any given
point of time either during the course of the contract or at the bidding stage, my bid/contract
shall be liable for truncation / cancellation / termination without any notice at the sole
discretion of the purchaser.
Yours faithfully,
Place-
Date-
Signature of Bidder with seal
(This form shall be duly filled-up and signed by the bidder & submitted along with the
original copy of the Bid.)
Page 37 of 47
ANNEXURE – III
PROFORMA FOR COMPOSITE BANK GUARANTEE FOR SECURITY DEPOSIT, PAYMENT AND
PERFORMANCE
Whereas SOUTHCO Utility , Corporate Office: Courtpeta, Berhampur, Ganjam - 760004 (here in after called “the
Purchaser”) has placed Purchase Order No._________ Dt.___________ (hereinafter called “the Agreement”) with
M/s_________________ _________________________ (hereinafter called “the Contractor”) for supply of
________________ (name of the material) and whereas SOUTHCO Utility has agreed (1) to exempt the Contractor
from making payment of security deposit, (2) to release 100% payment of the cost of materials as per the said
agreement and (3) to exempt from performance guarantee on furnishing by the Contractor to the SOUTHCO Utility
a composite Bank Guarantee of the value of 10% (ten percent) of the Contract price of the said Agreement.
1. Now, therefore, in consideration of SOUTHCO Utility having agreed (1) to exempt the Contractor for
making payment of security deposit, (2) to release 100% payment to the Contractor and (3) to exempt from
furnishing performance guarantee in terms of the said Agreement as aforesaid, we the ____________________
Bank, Address ____________________________ (code No. ________) (hereinafter referred to as “the Bank”) do
hereby undertake to pay to the SOUTHCO Utility an amount not exceeding Rs._____________ (Rupees
_______________________________ ) only against any loss or damage caused to or suffered by SOUTHCO Utility
by reason of any breach by the said Contractor(s) of any of the terms or conditions contained in the said
Agreement.
2. We, the ______________________ Bank do hereby undertake to pay the amounts due and payable under
the guarantee without any demur, merely on a demand SOUTHCO Utility stating that the amount claimed is due by
way of loss or damage caused to or suffered by SOUTHCO Utility by reason of any breach by the said Contractor(s)
of any of the terms or conditions contained in the said Agreement or by the reason of any breach by the said
Contractor’s failure to perform the said Agreement. Any such demand made on the Bank shall be conclusive as
regards the amount due and payable by the Bank under this Guarantee. However, our liability under this guarantee
shall be restricted to an amount not exceeding Rs.___________ (Rupees
_________________________________________ ) only.
3. We, the ________________________ Bank also undertake to pay to SOUTHCO Utility any money so
demanded not withstanding any dispute or dispute raised by the Contractor(s) in any suit or proceeding instituted/
pending before any court or Tribunal relating thereto our liability under this Agreement being absolute and
unrevocable.
The payment so made by us under this bond shall be valid discharge of our liability for payment there
under and the Contractor(s) shall have no claim against us for making such payment.
4. We, the _________________________ Bank further agree that the guarantee herein contain shall remain
in full force and affect during the period that would be taken for the performance of the said Agreement and it
shall continue to remain in force endorsable till all the dues of SOUTHCO Utility under by virtue of the said
Agreement have been fully paid and its claim satisfied or discharged or till SOUTHCO Utility certifies that the terms
and conditions of the said Agreement have been fully and properly carried out by the said Contractor(s) and
accordingly discharge this guarantee and will not be revoked by us during the validity of the guarantee period.
Page 38 of 47
_________________________________________________, Berhampur in writing on or before
__________________ (date) we shall be discharged from all liability under this guarantee thereafter.
5. We, the _________________________ Bank further agree that SOUTHCO Utility shall have the fullest
liberty without our consent and without affecting in any manner our obligations hereunder to vary any of the
terms and conditions of the said Agreement or to extend time of performance by the said Contractor(s) and we
shall not be relieved from our liability by reason of any such variation or extension being granted to the said
Contractor(s) or for any forbearance act or omission on part of SOUTHCO Utility or any indulgence by SOUTHCO
Utility to the said Contractor(s) or by any such matter or thing whatsoever which under the law relating to sureties
would but for this provisions have effect of so relieving us.
6. The Guarantee will not be discharged due to change in the name, style and constitution of the Bank and or
Contractor(s).
7. We, the _________________________ Bank lastly undertake not to revoke this Guarantee during its
currency except with the previous consent of SOUTHCO Utility in writing.
Our liability under this Bank Guarantee shall not exceed Rs.______________ (Rupees _______
____________________________________________________________________ ) only.
We or our Bank at Berhampur (Name & Address of the Local Bank) are liable to pay the guaranteed amount
depending on the filing of claim and any part thereof under this Bank Guarantee only and only if you serve upon us
or our local Bank at Berhampur a written claim or demand and received by us or by Local Branch at Berhampur on
or before Dt.__________ otherwise bank shall be discharged of all liabilities under this guarantee thereafter.
For _____________________________________
(indicate the name of the Bank )
N.B.:
(1) Name of the Contractor:
(11) The Bank Guarantee shall be accepted only after getting confirmation from the respective Banks.
Page 39 of 47
ANNEXURE –IV(A)
3. We, the _______________ Bank undertake to pay the SOUTHCO Utility any money so demanded not
withstanding any dispute or disputes so raised by the supplier [s] in any suit or proceeding instituted/pending
before any Court or Tribunal relating thereto, our liability under this agreement being absolute and unequivocal.
The payment so made by us under this bond shall be a valid discharge of our liability for payment there under and
the supplier(s) shall have no claim against us for making such payment.
4. We, the__________Bank [Indicate the name of the bank] or our local branch at Berhampur further agree that
the guarantee herein contain shall remain in full force and effect during the aforesaid period of -------------- days
and it shall continue to be so enforceable till all the dues of the SOUTHCO Utility under by virtue of the said Bid
have been fully paid and its claims satisfied or discharged or till SOUTHCO Utility certifies that the terms and
conditions of the said Bid have been fully and properly carried out by the said Supplier [s] and accordingly
Page 40 of 47
discharges this guarantee. Unless a demand or claim under this guarantee is made on us in writing on or before the
_________________ (date) we shall be discharged from all liability under this guarantee thereafter.
5. We, the __________Bank [Indicate the name of the bank] or our local branch at Berhampur further agree that
the SOUTHCO Utility shall have the fullest liberty without our consent and without affecting in any manner our
obligations here under to vary any of the terms and conditions of the said Bid or to extend time of performance by
the said Supplier [s] from time to time or to postpone for any time or from time to time any of the powers
exercisable by the SOUTHCO Utility against the said supplier [s] and to forbear or enforce any of the terms and
conditions relating to the said bid and we shall not be relieved from our liability by reason of any such variation,
postponement or extension being granted to the said Supplier [s] or for any forbearance act or omission on the
part of the SOUTHCO Utility or any indulgence by the SOUTHCO Utility to the said Supplier[s] or by any such
matter or thing whatsoever which under the law relating to sureties would but for this provision, have effect of so
relieving us.
6. This guarantee will not be discharged due to the change in the name, style and constitution of the Bank or the
supplier [s].
7. We, the ____________Bank or our local branch at Berhampur lastly undertake not revoke this Guarantee during
its currency except with the previous consent of the SOUTHCO Utility in writing.
8. We, the__________________________ Bank further agree that this guarantee shall also be invokable at our
place of business at Berhampur (detail address of local branch with code no.) in the State of Odisha.
Dated ________________________ Day of 2017.
Witness ((Signature, names & address) For_________ [Indicate the name of Bank]
1. Power of Attorney No.______
2 Date: _________
SEAL OF BANK
Note: The non-judicial stamp paper of worth Rs.100/- shall be purchased in the name of the bank, which has
issued the bank guarantee.
Page 41 of 47
ANNEXURE –IV(B)
Ref. No.________________
Dated: __________
Dear Sirs,
At the request of M/s. _____________we ____________ bank Branch office at ________ having its head
office at _____________ do hereby extend our liability under the above mentioned guarantee No.
___________ Dated__________ for a further period of _______ Years/months from ________to expire
on __________ except as provided above, all other terms and conditions of the original bank guarantee
No.__________dated __________ shall remain unaltered and binding.
Please treat this as an integral part of the original guarantee to which it would be attached.
Yours faithfully,
For ____________
Manager/Agent/Accountant
Power of Attorney No.______
Date: _________
SEAL OF BANK
Note: The non-judicial stamp paper of worth Rs.100/- shall be purchased in the name of the bank, which
has issued the bank guarantee.
Page 42 of 47
ANNXURE-V
Format for Consortium Agreement
(On non-judicial stamp paper of appropriate value to be purchased in the name of executants companies
or as required by the jurisdiction in which executed)
M/s ……………………………..a Company (SSI Unit) incorporated under the companies Act – 1956
………………………………………and having its registered office at ………………………….(hereinafter called the “Lead
Member/First member” which expression shall include its successors); and
M/s ………………………………….a company (SSI Unit) incorporated under the Companies Act – 1956
…………………………………….and having its registered office at …………………(hereinafter called the “Second Member”
which expression shall include its successors)and
M/s. …………………………….……..a company (SSI Unit) incorporated under the companies Act-
1956…………………………………………………..and having its registered office at ……………… (hereinafter called the “Third
Member” which expression shall include its successors)
The Lead Member/First Member, the Second Member, the Third Member and the Forth Member shall collectively
hereinafter be called as the “Consortium Members” for the purpose of submitting a bid proposal to SOUTHCO
Utility, having its corporate office at Courtpeta, Berhampur, Ganjam, Odisha - 760004 (hereinafter called the
“Purchaser”)in response to the invitation of bids (hereinafter called as “Tender Notice No………” Document) Dated
…………… for supply of Materials/Equipments (hereinafter called as “the Transaction”).
WHEREAS Clause-6.1.2 of the Invitation for Bids (IFB),stipulates that Two or more Local SSI Units having
been manufacturers of tender item(s) as per this tender specification, provided they fulfill the following
eligible criteria;
a) They should have legally valid consortium agreement as per the prescribed format for the purpose of
participation in the bidding process. The total no of a consortium shall be limited to four members.
b) All members of the Consortium should be the eligible manufacturer(s) of the materials / equipments
tendered.
c) Consortium as a whole shall meet the qualifying norms specified in the tender, they participate.
d) The lead member of the Consortium should meet at least 50% of the qualifying norms in respect of the
supply experience.
e) Besides the lead member, other member (s) of the Consortium should meet at least 15% of the qualifying
norms in respect of the supply experience.
f) All the Consortium member(s) shall authorize the lead partner by submitting a power of Attorney as per
the prescribed format duly signed by the authorized signatories. The lead partner shall be authorized to
receive instructions for and on behalf of all partners of the Consortium and entire execution of the contract
including receipt of payment exclusively done through the lead partner.
g) The Consortium and its members shall be jointly and severally responsible and be held liable for the
purpose of guaranteed obligation and any other matter as required under the contract.
h) Any member of the Consortium member(s) shall not be eligible either in an individual capacity or part of
any other consortium to participate in the tender, where the said consortium participates.
i) The prescribed formats for Consortium Agreement (Annexure – IV) and Power of Attorney (Annexure – V)
are provided in the tender specification as enclosures.
Page 43 of 47
AND WHEREAS the members of the Consortium strictly comply the eligible criteria of the CLAUSE -6.1.2
of the Invitation for Bids (IFB) as stipulated above,
AND WHEREAS bid has been proposed to be submitted to the purchaser vide bid by Lead Member based
on this CONSORTIUM agreement between all the members, signed by all the members.
In consideration of the above premises, in the event of the selection of Consortium as successful bidder, all the
Parties to this Consortium Agreement do hereby agree abide themselves as follows:
1. M/s ……………………….shall act as Lead Member for and on behalf of Consortium Members. The said
Consortium members further declare and confirm that they shall jointly and severally be bound and shall
be fully responsible to the Purchaser for the design, manufacture, supply, and successful performance of
the materials /equipment, obligations under the supply contract under Agreement(s) submitted/executed
by the Lead Member.
2. Despite any breach by the Lead Member or other member(s) of the CONSORTIUM agreement, the
Member(s) do hereby agree and undertake to ensure full and effectual an successful performance of the
contract with Purchaser and to carry out all the obligations and responsibilities under the said Contract in
accordance with the requirements of the Contract.
3. If the Purchaser suffers any loss or damage on account of any breach of the Contract or any shortfall in the
performance in meeting the performance guaranteed as per the specification in terms of the Contract, the
Member(s) of these presents undertake to promptly make such loss or damage caused to the purchaser,
on its demand without any demur. It shall not be necessary or obligatory for the purchaser to proceed
against Lead member to these presents before proceeding against or dealing with the other members. The
obligation of each of the member is absolute and not independent of the consortium or any member.
4. The financial liability of the members of this CONSORTIUM agreement to the Purchaser, with respect to
any of the claims arising out of the performance or non- performance of the obligations set forth in the
said CONSORTIUM agreement, read in conjunction with relevant conditions of the contract shall, however,
not be limited in anyway so as to restrict or limit the liabilities of any of the members of the CONSORTIUM
agreement. The liability of each member is absolute and not severable.
5. It is expressly understood and agreed between the members to this CONSORTIUM agreement that the
responsibilities inter se amongst the members shall not in any way be a limitation of joint and several
responsibilities and liabilities of the Members to the Purchaser. It is clearly understood that the lead
member shall ensure performance under the agreement(s) and if one or more Consortium members fail to
perform its/their respective obligations under the agreements, the same shall be deemed to be a default
by all the Consortium Members. It will be open for the purchaser to take any steps, punitive and corrective
action including the termination of contract in case of such default also.
6. This CONSORTIUM agreement shall be construed and interpreted in accordance with the laws of India and
shall be subjected to exclusive jurisdiction within Berhampur in all matters arising there under.
7. In case of an award of a Contract, all the members to the CONSORTIUM agreement do hereby agree that
they shall be jointly and severally responsible for furnishing a contract performance security from a bank in
favour of the purchaser in the forms acceptable to purchaser for value of 10% of the Contract price. It is
also hereby agreed that the lead member shall, on behalf of the CONSORTIUM submit the contract
performance security in the form of an unconditional irrecoverable Bank guarantee in the prescribed
format and as per terms of the contract.
8. It is further agreed that the CONSORTIUM agreement shall be irrevocable and shall form an integral part of
the Contract, and shall continue to be enforceable till the Purchaser discharges the same. It shall be
effective from the date first mentioned above for all purposes and intents.
9. Capitalized terms used but not defined herein shall have the meaning as assigned to them to the Tender
Documents and/or the agreements.
10. In case of any dispute amongst the members of the Consortium, purchaser shall not be in any way liable
and also the consortium members shall not be absolved from the contractual obligation in any manner.
Page 44 of 47
IN WITNESS WHEREOF the Members to the CONSORTIUM agreement have through their authorized
representatives executed these presents and affixed Common Seals of their companies, on the day, month and
year first mentioned above.
WITNESSES
1………………………………… 2. ……………………………………
(Signature) (Signature)
Name ………………………….. Name ………………………….
Page 45 of 47
ANNEXURE – VI
(On Non-Judicial Stamp Paper of Appropriate value to be purchased in the Name of CONSORTIUM)
KNOW ALL MEN BY THESE PRESENTS THAT WE, the Members whose details are given hereunder……………………have
formed a CONSORTIUM and having our Registered Office (s)/Head Office (s) at …………………………………… (hereinafter
called the ‘Consortium’ which expression shall unless repugnant to the context or meaning thereof, include its
successors, administrators and assigns) do hereby constitute, nominate and appoint M/s ………………………………. A
company incorporated under the laws of ……………… and having its Registered/Head office at ……………….as our duly
constituted lawful Attorney (hereinafter called “Lead Member”) to exercise all or any of the powers for supply
…………………………………….for which bids have been invited by the Purchaser namely SOUTHCO Utility (SOUTHCO),to
undertake the following acts:
(i) To submit proposal, participate and negotiate in respect of the aforesaid Bid – Specification of the
Purchaser on behalf of the “Consortium”
(ii) To negotiate with Purchaser the terms and conditions for award of the contract pursuant to the
aforesaid Bid and to sign the contract with the Purchaser for and on behalf of the “Consortium”
(iii) To do any other act or submit any document related to the above.
(iv) To receive, accept and execute the contract for and on behalf of the “Consortium”.
(v) To submit the contract performance security in the form of an unconditional irrecoverable Bank
guarantee in the prescribed format and as per terms of the contract.
It is clearly understood that the Lead Member shall ensure performance of the contracts(s) and if one or more
Member fail to perform their respective portion of the contracts (s), the same shall be deemed to be a default by
all the members.
It is expressly understood that this power of Attorney shall remain valid binding and irrevocable till completion of
the defect or liability period in terms of the contract.
The CONSORTIUM hereby agrees and undertakes to ratify and confirm all the whatsoever the said Lead Member
quotes in the bid, negotiates and signs the contract with the Purchaser and / or proposes to act on behalf of the
CONSORTIUM by virtue of this Power of Attorney and the same shall bind the CONSORTIUM as if done by itself.
IN WITNESS THEREOF the members Constituting the CONSORTIUM as aforesaid have executed these presents on
this …………..day of ………..under the Common Seal (s) of their Companies.
1. -----------------------------------------
2. -----------------------------------------
3. -----------------------------------------
4. -------------------------------------------
The Common Seal has been affixed there unto in the presence of:
Page 46 of 47
WITNESS
1. Signature…………………………..
Name…………………………….
Designation……………………………
Occupation……………………………
2. Signature…………………………..
Name…………………………….
Designation……………………………
Occupation……………………………
Page 47 of 47