Catalogo McGUILL
Catalogo McGUILL
Catalogo McGUILL
McGill has worked closely with its customers to serve global needs of industry with a complete series of
Metric Cam Followers. The McGill standard Metric CAMROL is manufactured to ISO standards and Asian
designs. The metric stud type MCF and cam yoke roller MCYR share all the same high-quality features as
other CAMROL Bearings. Each Cam Follower is supplied with two nuts and appropriate metric threads;
the second nut is intended to serve as a locknut. All designs use the patented LUBRI-DISC® Seals that
provide positive protection against contamination and loss of lubricant. LUBRI-DISC Seals reduce internal
bearing friction – bearings wear less and last longer.
Easy to Upgrade
Grease Fitting McGill bearings are interchangeable with European
Included fitting head provides easy fit and Asian brand metric cam followers.
with standard hydraulic grease gun. See www.RegalPTS.com for interchange assistance.
2
MCFD Series Two Rows of Cylindrical Rollers
Full complement design, engineered for
higher load, higher speed applications.
Labyrinth Type Sealing
Contents Page
Engineering Data...................................................................... 2
MCF Series - Needle Rollers/Stud Type...................................... 8
MCYR Series - Needle Rollers/Yoke Type................................. 10
MCFD Series - Cylindrical Rollers/Stud Type............................. 12
MCYRD Series - Cylindrical Rollers/Yoke Type.......................... 13
Eccentric Collar CAMROL Bearings.......................................... 14
Interchangeability Charts....................................................... 15
3
McGill® Metric Camrol® Bearings
McGill offers METRIC CAMROL Bearings in metric dimensions These dynamic and static ratings are less than those
equivalent to the ISO standard series. Both European and calculated by the basic load rating formulas (C and Co) and
Asian versions are available. account for the additional bending stresses present because
the outer ring is unsupported. The load applied on the
bearing while it is operating dynamically should not exceed
50% of the dynamic rating as a track roller.
Bearing Life
Statistical L10 bearing fatigue life can be calculated according
to the following formula:
16666
( BDR
P )
10/3
L10 life in hours = X
N
Stud Type Yoke Type
Where:
BDR = Basic Dynamic Rating (Newtons)
P = Radial Load (Newtons)
McGill METRIC CAMROL Bearings are available in stud or yoke N = Speed (RPM)
type versions. Specifying the yoke type or stud type bearing L10 = Fatigue Life (Hours)
will depend on the preference for either a straddle (yoke)
mounting or a cantilever (overhung) mounting. To determine the basic dynamic rating required for a given
application, use the following formula:
4
www.RegalPTS.com/McGill
5
McGill® Metric Camrol® Bearings
LOAD
Yoke Mounting
TI ON
MO LOAD
LOAD
M
OT
ION
MOTION LOAD
6
www.RegalPTS.com/McGill
Stud Type
Metric stud type CAMROL Bearings are available with Series Construction Features
a hexagonal hole in the face of the stud in place of the MCF Full complement of needle rollers
screwdriver slot. This feature is advantageous for mounting
MCFE With eccentric collar
bearings in blind holes or with self-locking nuts requiring
greater-than-average thread torque. In this modification, MCF-X With cylindrical outside diameter
relubrication through the flange end of the stud is not MCF-B, MCF-BX With hexagonal hole
possible. MCF-S, MCF-SBX With seals
MCFR Caged needle rollers
Hexagonal Wrench Sizes MCFRE With eccentric collar
MCFR-X With cylindrical outside diameter
Basic Bearing Hex Wrench Basic Bearing Hex Wrench MCFR-B, MCFR-BX With hexagonal hole
Number Size, mm Number Size, mm
MCFR-S, MCFR-SBX With seals
13 3 47 10
MCFD Full complement cylindrical rollers
16 4 47A 10
MCFDE With eccentric collar
19 4 52 10
MCFD-X With cylindrical outside diameter
22 4 52A 10
22A 5 62 14
26 4 62A 14
26A 5 72 14
30 6 72A 14
32 6 80 14
35 8 85 14
40 8 90 14
40A 8
Yoke Type
MCF SERIES L
W SL
STUD TYPE R E
HC
TL
Series MCF — Unsealed, full complement
HD
Series MCF-S — Sealed, full complement
Series MCFR — Unsealed, cage type RD D D SD
Series MCFR-S — Sealed, cage type
MCF
500mm RADIUS
MCFR-26 MCFR-26-S 26 12 10 23 36 0 .6 M 1 0 x1 12 - -
MCF-26 MCF-26-S
MCFR-26A MCFR-26A-S 26 12 10 23 36 0 .6 M10x1.25 13 - -
MCF-26A MCF-26A-S
MCFR-30 MCFR-30-S 30 14 12 25 40 0 .6 M12x1.5 14 6 3
MCF-30 MCF-30-S
MCFR-32 MCFR-32-S 32 14 12 25 40 0 .6 M12x1.5 14 6 3
MCF-32 MCF-32-S
MCFR-35 MCFR-35-S 35 18 16 32.5 52 0 .8 M16x1.5 18 8 3
MCF-35 MCF-35-S
MCFR-40 MCFR-40-S 40 20 18 36.5 58 0 .8 M18x1.5 19 8 3
MCF-40 MCF-40-S
MCFR-40A MCFR-40A-S 40 20 18 36.5 58 0 .8 M18x1.5 20 10 3
MCF-40A MCF-40A-S
MCFR-47 MCFR-47-S 47 24 20 40.5 66 0 .8 M20x1.5 21 9 4
MCF-47 MCF-47-S
MCFR-47A MCFR-47A-S 47 24 20 40.5 66 0 .8 M20x1.5 22 12 4
MCF-47A MCF-47A-S
MCFR-52 MCFR-52-S 52 24 20 40.5 66 0 .8 M20x1.5 21 9 4
MCF-52 MCF-52-S
MCFR-52A MCFR-52A-S 52 24 20 40.5 66 0 .8 M20x1.5 22 12 4
MCF-52A MCF-52A-S
MCFR-62 MCFR-62-S
MCF-62 MCF-62-S 62 29 24 49.5 80 0 .8 M24x1.5 25 11 4
(1) Standard bearing has a crowned roller outside diameter. For straight cylindrical outside roller diameter, add suffix "X". Example - MCFR-35-X or MCF-35-SX
(2) Tolerance limits for Roller Diameter are shown below.
8
www.RegalPTS.com/McGill
MCF SERIES
L
W SL
R E HC TL
HD
RD D D SD
MCFR-S
500mm RADIUS
(3) Stud Diameter "SD" per ISO tolerance h7, shown below. (4) Clamping torque is based on dry threads. If threads are lubricated, use half
of value shown.
(5) Static load rating is based on stud strength or on internal rolling element
Stud Dia. "SD" load distribution stresses.
(6) Dynamic load should not exceed 50% of Dynamic Rating as a track roller.
SD (NOM.) TOLERANCE (7) Since load, lubrication method, temperature and other factors affect the
maximum operating speed, it is impossible to determine precise limiting speed.
OVER INCL. MAX. MIN. The listed limiting speeds are based on lightly loaded bearings having adequate
mm mm mm mm lubrication and are listed only as a design guide. More frequent relubrication is
2 6 0 -0.012 required when operating at higher speeds. Actual bearing testing in the specific
6 10 0 -0.015 application should be conducted if the anticipated operating speed approaches
the listed limiting speed.
10 18 0 -0.018
18 30 0 -0.021
• Sizes marked have no lube holes in threaded end of stud.
9
McGill® Metric Camrol® Bearings
MCYR SERIES W1
R W
YOKE TYPE
Series MCYR — Unsealed, full complement
Series MCYR-S — Sealed, full complement
Series MCYRR — Unsealed, cage type
Series MCYRR-S — Sealed, cage type RD E B
MCYR
500mm RADIUS
BEARING DIMENSIONS
(1) Standard bearing has a crowned roller outside diameter. For straight cylindrical outside diameter, add suffix "X". (Example - MCYRR-15-X or MCYR-15-SX)
(2) Tolerance limits for Roller Diameter are shown below.
10
www.RegalPTS.com/McGill
MCYR SERIES W1
W
R
RD E B
MCYRR-S
500mm RADIUS
mm mm mm mm mm rpm rpm ( 5) kg
MCYRR-5 MCYRR-5-S 19500 25000 4120 4120 3430 3380 0 .0 1 1
4.996 4.988 5 4 .9 9 2 11
MCYR-5 MCYR-5-S 13000 17000 6960 8340 5790 6900 0.014
MCYRR-6 MCYRR-6-S 15500 20000 4510 5000 3730 4090 0.018
5.996 5.988 6 5.992 13
MCYR-6 MCYR-6-S 10500 13500 8040 10490 6670 8760 0.021
MCYRR-8 MCYRR-8-S 12500 16000 6860 7750 5690 6450 0.040
7.995 7.986 8 7 .9 9 1 16
MCYR-8 MCYR-8-S 8400 11000 11470 15200 9610 12600 0.043
MCYRR-10 MCYRR-10-S 9600 12500 8240 9710 6860 8050 0.060
9.995 9.986 10 9.991 19
MCYR-10 MCYR-10-S 6400 8300 13340 18240 11080 15300 0.062
MCYRR-12 MCYRR-12-S 8100 1 0500 8730 10890 7260 9120 0.067
1 1 .9 9 4 11.983 12 11.989 21
MCYR-12 MCYR-12-S 5400 7000 14420 20890 12060 17400 0.069
MCYRR-15 MCYRR-15-S 6300 8200 13040 19030 10890 15900 0.102
1 4 .9 9 4 14.983 15 14.989 24
MCYR-15 MCYR-15-S 4200 5400 20300 34130 16970 28500 0.105
MCYRR-17 MCYRR-17-S 4900 6400 15990 23730 13340 19700 0.150
1 6 .9 9 4 16.983 17 16.989 27
MCYR-17 MCYR-17-S 3300 4300 23240 38540 19420 32200 0.153
MCYRR-20 MCYRR-20-S 3900 5000 21280 35700 17750 29800 0 .252
19.993 19.980 20 19.987 30
MCYR-20 MCYR-20-S 2600 3400 30790 57670 25690 48000 0.255
MCYRR-25 MCYRR-25-S 3300 4300 22950 41780 19120 34900 0.278
24.993 24.980 25 24.987 36
MCYR-25 MCYR-25-S 2200 2900 34130 70410 28440 58700 0.284
MCYRR-30 MCYRR-30-S 2500 3200 34030 65120 28340 54300 0.465
29.993 29.980 30 29.987 44
MCYR-30 MCYR-30-S 1700 2200 49720 107290 41480 89000 0.476
MCYRR-35 MCYRR-35-S 2200 2800 38930 72960 32460 60900 0.636
34.991 34.975 35 34.984 52
MCYR-35 MCYR-35-S 1500 1900 56880 120230 47370 100000 0.649
MCYRR-40 MCYRR-40-S 1900 2400 49720 94440 41480 78700 0.825
39. 991 39.975 40 39.984 58
MCYR-40 MCYR-40-S 1300 1700 70020 147990 58350 123000 0.845
MCYRR-45 MCYRR-45-S 1800 2300 51190 101010 42760 84100 0.901
44.991 44.975 45 44.984 63
MCYR-45 MCYR-45-S 1200 1500 73750 163190 61490 136000 0.924
MCYRR-50 MCYRR-50-S 1600 2000 54720 113570 45600 94800 0.960
44.991 49.975 50 49.984 68
MCYR-50 MCYR-50-S 1100 1400 77180 178390 64330 148000 0.984
(3) For a tight fit and heavy loads, use ISO tolerance j6.
(4) Since load, lubrication method, temperature and other factors affect the maximum operating speed, it is impossible to determine precise limiting speed. The listed
limiting speeds are based on lightly loaded bearings having adequate lubrication and are listed only as a design guide. If grease lubricated, frequent relubrications
is required. Actual bearing testing in the specific application should be conducted if the anticipated operating speed approaches the listed limiting speed.
(5) Dynamic load should not exceed 50% of Dynamic Rating as a track roller.
11
McGill® Metric Camrol® Bearings
MCFD SERIES
L
W SL
STUD TYPE E HC TL
HD
Series MCFD — Shielded, full complement of cylindrical rollers
RD D D SD
MCFD
ROLLER
ROLLER STUD OVERALL ENDPLATE THREAD REAMED
DIA. STUD DIA.
WIDTH L'GTH. LENGTH EXTENSION LENGTH OIL HOLE HOLE
RD SD
W SL L E THREAD TL D
BEARING (1)
NO. +0.00
NOM.
HC HD
NOM. -0.12 NOM. NOM. NOM. NOM. MIN. NOM.
NOM. NOM.
mm mm mm mm mm mm mm mm mm mm mm
MCFD-35 35 18 16 3 2 .5 52 0.8 M16x1.5 17 8 3 6
MCFD-40 40 20 18 3 6 .5 58 0.8 M18x1.5 19 8 3 6
MCFD-47 47 24 20 4 0 .5 66 0.8 M20x1.5 21 9 4 8
MCFD-52 52 24 20 4 0 .5 66 0.8 M20x1.5 21 9 4 8
MCFD-62 62 29 24 4 9 .5 80 0.8 M24x1.5 25 11 4 8
MCFD-72 72 29 24 4 9 .5 80 0.8 M24x1.5 25 11 4 8
MCFD-80 80 35 30 6 3 .0 100 1 .0 M30x1.5 32 15 4 8
MCFD-90 90 35 30 6 3 .0 100 1 .0 M30x1.5 32 15 4 8
(1) Standard bearing has a crowned roller outside diameter. For straight cylindrical outside diameter, add suffix "X". (Example - MCFD-35-X)
(2) Since load, lubrication method, temperature and other factors affect the maximum operating speed, it is impossible to determine precise limiting speed.
The listed limiting speeds are based on lightly loaded bearings having adequate lubrication and are listed only as a design guide. If grease lubricated, frequent relubrication is
required. Actual bearing testing in the specific application should be conducted if the anticipated operating speed approaches the listed limiting speed.
(3) Clamping torque is based on dry threads. If threads are lubricated, use half of value shown.
OVER INCL. MAX. MIN. OVER INCL. MAX. MIN. OVER INCL. MAX. MIN.
mm mm mm mm mm mm mm mm mm mm mm mm
30 50 0 -0.011 30 120 0 -0.050 10 18 0 -0.018
50 80 0 -0.013 18 30 0 -0.021
80 120 0 -0.015
12
www.RegalPTS.com/McGill
MCYRD SERIES
WI(3)
YOKE TYPE W
RO
Series MCYRD — Shielded, full complement of cylindrical rollers
RI
RD B E
(1) Standard bearing has a crowned roller outside diameter. For straight cylindrical outside diameter, add suffix "X". (Example - MCYRD-15-X)
(2) Since load, lubrication method, temperature and other factors affect the maximum operating speed, it is impossible to determine precise limiting speed. The listed
limiting speeds are based on lightly loaded bearings having adequate lubrication and are listed only as a design guide. If grease lubricated, frequent relubrication
is required. Actual bearing testing in the specific application should be conducted if the anticipated operating speed approaches the listed limiting speed.
3) Positive clamping across endplates required to insure proper end play after mounting.
13
McGill® Metric Camrol® Bearings
ECC.
BD
*For positive clamping, housing thickness should be 0.3 mm greater than G dimension.
14
www.RegalPTS.com/McGill
INTERCHANGEABILITY CHARTS
15
Regal Power Transmission Solutions
7120 New Buffington Road
Florence, KY 41042
Customer Service: 800-626-2120
Fax: 800-262-3292
Technical Service: 800-626-2093
www.RegalPTS.com
APPLICATION CONSIDERATIONS
The proper selection and application of power transmission products and components, including the related area of product safety, is the responsibility
of the customer. Operating and performance requirements and potential associated issues will vary appreciably depending upon the use and application
of such products and components. The scope of the technical and application information included in this publication is necessarily limited. Unusual
operating environments and conditions, lubrication requirements, loading supports, and other factors can materially affect the application and
operating results of the products and components and the customer should carefully review its requirements. Any technical advice or review furnished
by Regal Beloit America, Inc. and its affiliates with respect to the use of products and components is given in good faith and without charge, and Regal
assumes no obligation or liability for the advice given, or results obtained, all such advice and review being given and accepted at customer’s risk.
For a copy of our Standard Terms and Conditions of Sale, Disclaimers of Warranty, Limitation of Liability and Remedy, please contact Customer Service
at 1-800-626-2120. These terms and conditions of sale, disclaimers and limitations of liability apply to any person who may buy, acquire or use a Regal
Beloit America Inc. product referred to herein, including any person who buys from a licensed distributor of these branded products.
Camrol, Lubri-Disc and McGill are trademarks of Regal-Beloit Corporation or one of its affiliated companies.
©2015 Regal-Beloit Corporation, All Rights Reserved. MCB15046E • Form# 9083E • Printed in USA