E2209wf - Monitor - 44 - 51
E2209wf - Monitor - 44 - 51
Service Manual
LCD Monitor E2209Wf
0
Downloaded from www.Manualslib.com manuals search engine
1
Copyright
Copyright 2007 InnoLux Display. Corp. Ltd
This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any
electronic or machine readable form without prior written permission of Foxconn Tech. Corp. Ltd.
2
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 1- PRECAUTIONS & SAFETY NOTICES
SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes first.
However, improper used or installation may cause damage to the monitor as well as to the user.
WARNINGS:
This monitor should be operated only at the correct power sources indicated on the rating label on
the rear cover of the monitor. If you’re unsure the power supply in your residence, consult your
local dealer or Power Company.
Use only the specified power cord that comes with this monitor.
Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. This monitor
should only be repaired by a qualified technician.
Do not remove the monitor cabinet. There is high-voltage parts inside that may cause electric shock
to human bodies.
Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable
immediately and consult your closed dealer.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the class screen.
Do not place heavy objects on the monitor or power cord.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated
for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this
manual carefully. The use of substitute replacement parts, which do not have the same safety
characteristics as specified in the parts list, may create shock, fire, or other hazards.
SERVICE NOTES
When replacing parts on circuit boards, clamp the solder wires around terminals before soldering.
Keep wires away from high voltage, high temperature components and sharp edges.
Keep wires in their original position so as to reduce interference.
Adjustment of this product please refers to the user’ manual.
Use Pb free solder wire for circuit board preparation.
3
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 2- SERVICE TOOLS & EQUIPMENT REQUIRED
1. SIGNAL GENERATOR
2. MULTIMETER
3. SCREW DRIVER
4. OSCILLOSCOPE
5. Soldering IRON
6. SOLDER (Lead free, RoHS compliance)
7. Color Analyzer
8. Fox_VISP_Programmer
9. Fox_VEDID_Programmer
4
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 3- CIRCUIT THEORY
Block Diagram
There are 3pcs PCBA in this monitor, one is power& inverter&Audio board which is a single layer board,
one is interface board including USB HUB 1up/2down, one is keypad which is OSD control, and one is
USB transfer board located on the right side back cover. The system function block diagram as below
This PWA is included switching power supplier, inverter for CCFL and interface board.(fig.1)
INVERTER POWER
Fig.1
5
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Fig.12
6
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Fig.2
27VDC provides the power for U1; the control signals Brightness and ON/OFF come from I/F
board. ON/OFF signal connect to pin16 of U1 and makes U1 enable. Brightness signal connect to
pin12 of U1 and regulates the panel brightness, make up a network of delaying time circuit and R23
make up a divided voltage network, C3 is used to control start-up timing. The operation
frequency is determined by the external Resistor R16 and capacitor C8 connected to pin3 of U1.
C7 is used for soft start and compensation.
The output drives, include DRV1, DRV2 (pins8,9 respectively) output square pulses to drive
MOSFET Q6, Q7 and each of Q6, Q7 is consist of a N+P channel MOSFET. Q6 and Q7 work as All
Bridge structure, it is high efficient, PWM switching.
During start up, VSEN (pin1) senses the voltage at the transformer secondary. When VSEN
reaches 3.0V, the output voltage is regulated. If no current is sensed approximately 2seconds U1 shut
off.
The current flowing through CCFL is sensed and regulated through sense resistor R6, R19. The
feedback voltage connected to Pin1 (ISEN), then compared with a reference voltage (1.5V) via a
current amplifier, resulting in PWM drive outputs to All Bridge switches.
2.1.2)Protection Circuit
7
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Over Voltage Protection and over-current protection are monitored by the voltage on VSEN(Pin
1) During normal operation , if a CCFL is damaged or removed ,the voltage at VSEN (Pin1)
increases .Once the voltage at VSEN exceeds 3.0V (OVPT Setting) the driver output duty cycle is
regulated and the shutdown delay timer is activated. OVPT set the overall protection threshold voltage
that is lower than 3V (VSEN threshold). Once the voltage at TIMER pin reached about 3v ,the IC will
shut down and latch . R3, R4,R14,R15,C1,C15,C16,C17 are connected in high voltage output
connector, the divided AC voltage is inverted DC voltage through D2, D3, R9 and C11 are used to
rectify wave & dump noise. Then the voltage signal reaches Pin1 VSEN of U1, when the voltage
changes, build-in PWM of U1 will adjust output voltage.
Open Lamp Protection: In normal operation, R10,R11 are sensed a high level DC voltage,If a
CCFL is removed or damaged during normal ,the voltage at SSTCMP(Pin2) rises rapidly .when the
voltage at SSTCMP reaches a threshold of approximately 2.0V,a current source charges the
capacitor(C3 and C18)connected to TIMER(Pin12).Once the voltage level at the TIMER pin reaches a
threshold of approximately 3.3v,The drive outputs shut down and latch .
EMI Filter Rectifier and Isolation power Rectifier and filter Inverter circuit
filter transformer
Interface
circuit
Feedback Isolation
fig.5
CN850 is a connector for connecting AC Power. F850 is a fuse to protect all the circuit AC. Input
8
Downloaded from www.Manualslib.com manuals search engine
Service Manual
voltage is from 90V to 264V. R850/R851/R852 are joined between two inputting main circuit to prevent
man from shock. L850 is used to filter low frequency noise. C850 and C851 are used to discharge the
noise that L850 produced. High frequency waves are damped by C852;
fig.6
D850 is a rectifier in which there are 4 build-in diodes, inverting AC to DC.
C854 is used to smooth the wave from rectifier. U850 is a highly integrated PWM controller.
Typical start-up current for U850 is only 20 uA, When current flow through R841/R842/R843 gets to
Pin 3of U850, with VDD hold-up capacitor C855, U850 is enough for starting up.
When U850 begins to operate Pin8 of U850 will output square wave to drive Q850, then the main
current flow get to GND bypassing through T850, Q850. Because of the change of current flow, wires in
the other side of T850 will induct current. In the same time, the current inducted by wires which
connected T850 Pin 1 and Pin 3, with components of D852, R856and C855 ,will be supplied to U850 for
normal operating.
9
Downloaded from www.Manualslib.com manuals search engine
Service Manual
When the sense voltage across the sense resistor R859, reaches the threshold voltage around 0.85v,
the output GATE drive will be turned off. Every time when the output of power supply is shorted or over
loaded, the FB voltage will increase, the build-in PWM output will then be turned off. Both of two will
prevent the power supply from being overheated under over loading condition. The PWM duty cycle is
determined by this current sense signal and VFB, the feedback voltage, when the voltage on sense pin
reaches V-(PWMcopm) =(Vcomp-2VF)/3, A switch cycle will be terminated immediately, Vcomp is internally
clamped to a variable voltage around 0. 85 V for output power limit
When Q850 are turned off, the main current flow will be consumed through D851, C875,
R853/R854/R855 and D853, This will prevent Q850 from being damaged under large current impulse and
voltage spike.
2.2.4)DC_27V and 5V Output Circuit and Feedback circuit:(fig.7)
fig.7
D854/D855 is used to rectify the inducted current. C862 is used to store energy when current is
reversed. The parts including C863 are used to smooth the current waves that are from D854/D855, then
27V voltage is supplied;
D860 is used to rectify the inducted current. R861 and C873 are used to store energy when current is
reversed. The parts including C866, C867, C868, and L854 are used to smooth the current waves that are
from D860, then 5Vvoltage is supplied;
27V and 5V supply voltage feed back to PWM controller U850 via R871, R872, R868 and
I850,I851.R860,C859 and C871 used to control respond time.
10
Downloaded from www.Manualslib.com manuals search engine
Service Manual
2.3 I/F Board Circuit (see the Attachment 2- Schematic)
2.3.1 RGB CAPTURE
- Signal RED,GREEN,BLUE input through CN102 #1,#2,#3, Stop DC via C113, C114 and C115, and
then enter into U105 (TSUMU58EHJ-LF-2) analog input PIN #28,#25,#23, and then
TSUMU58EHJ-LF-2 deals with signal internally. D103, D104, D105 are ESD protector to prevent
U105 from ESD.
- Signal DDC_SCL (series clock) inputs via CN102#15, and then passes through ZD106 for ESD
protection, goes into EDID EEPROM IC U103 #6.
- Signal DDC_SDA (series data) inputs via CN102#12, and then passes through ZD103 for ESD
protection, goes into EDID EEPROM IC U103 #5.
- Signal TTL vertical sync. (Vsync) inputs via CN102 #14, and then clamped by ZD105 Zener, passes
through R134, and then goes into IC U105 (TSUMU58EHJ-LF-2) #33.
- Signal TTL horizontal sync. (Hsync) inputs via CN101 #13, and then clamped by ZD102 Zener,
passes through R133, and then goes into IC U105 (TSUMU58EHJ-LF-2) #32.
- CN101#5 is defined as cable detect pin, this detector realize via R121 and U104#36, and D102 is
ESD protector.
- U103 +5V is supplied by PC via CN102#9 with ZD102 for ESD protection, or supplied by Monitor
self via D106
- U103 is an EEPROM IC which is memory and EDID data saved in it.
2.3.2 DVI CAPTURE
- Differential Signal input RX0+,RX0-,RX1+,RX1-,RX2+,RX2-,RXC+,RXC- through CN201
#18,#17,#10,#9,#2,#1,#23,#24 via R206,R205,R204,R203,R202,R201,R207,R208 enter into U105
(TSUMU58EHJ-LF-2) Digital input terminal #16,#15,#13,#12,#10,#9,#18,#19, and then
TSUMU58EHJ-LF-2 deals with signal internally. D206, D207, D204, D205, D202, D203, D208,
D209 are ESD protector to prevent U105 from ESD
- Signal DDC_SCL (series clock) inputs via CN201#6, and then passes through ZD204 Zener for ESD
protection, via R209, goes into EDID EEPROM IC U201 #6.
- Signal DDC_SDA (series data) inputs via CN201#7, and then passes through ZD203 Zener for
ESD protection, via R210, goes into EDID EEPROM IC U201 #5.
- CN201#15 is defined as cable detect pin, this detector realize passes through R216 ,go into U105#49,
and D210 is ESD protector.
- U201 +5V is supplied by PC via CN201#14 through D201, or supplied by Monitor self via D201.
- U201 is an EEPROM IC which is memory and DVI input EDID data saved in it.
2.3.3 Buttons Control
- Button “Power” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #4 through CN104 #8, U105
#4 is defined as power on/off.
- Button “+” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #120 through CN104 #2,
U105#120 Voltage is defined as “Plus”.
- Button “-” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #121 through CN104 #3, U105
#121 Voltage is defined as “Minus”.
- Button “Menu” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #50 through CN104 #1,
U105 #50 Voltage is defined as “Menu”.
- Button “SELECT” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #122 through CN104 #4,
U105 #122 Voltage is defined as “SELECT”.
- LED Indicator on Front Bezel
a. When press button “power”, U105 (TSUMU58EHJ-LF-2) #123 be send in low Voltage, make
Q107#3 sends out high Voltage , and then to CN01#5 on keypad, LED green on.
b. When in “Suspend” mode, U105 (TSUMU58EHJ-LF-2) #124 sends out a low Voltage, make
Q108#3 sends out high Voltage and then to CN01 #7 on keypad, LED Amber ON.
2.3.4 MATAR CHIP U105 (TSUMU58EHJ-LF-2)
- U105 (TSUMU58EHJ-LF-2) #91~#100 output 8 bit even and #77~#86 output 8 bit odd LVDS digital
data to panel control circuit through CN103.
11
Downloaded from www.Manualslib.com manuals search engine
Service Manual
- U105 (TSUMU58EHJ-LF-2) #73 output PPWR ”H” potential to make Q104 conducted, and then
make Q101 conducted, +5V flow to CN103#1~#3 as Panel Vdd .
- U105 (TSUMU58EHJ-LF-2) #109 output CCFL_ON/OFF ”L” potential to control Inverter on/off.
- U105 (TSUMU58EHJ-LF-2) #125 outputs Brightness “PWM” signals to control CCFL brightness.
- TCLK by Crystal 14.318MHz input to U105 (TSUMU58EHJ-LF-2) #128/#127.
- U105 (TSUMU58EHJ-LF-2)#108 is RESET signals input pin
12
Downloaded from www.Manualslib.com manuals search engine
Service Manual
10%
0V 10%
T1 T2
T5 T6 T7
T3 T4
Power supply for backlight
Pin Symbol
1 Line
2 GND
3 Neutral
13
Downloaded from www.Manualslib.com manuals search engine
Service Manual
7 GND_LVDS LVDS Ground
8 RXE3+ LVDS signal of even channel 3(-)
9 RXE3- LVDS signal of even channel 3(+)
10 RXEC+ LVDS signal of even channel clock (+)
11 RXEC- LVDS signal of even channel clock (-)
12 RXE2+ LVDS signal of even channel 2(+)
13 RXE2- LVDS signal of even channel 2(-)
14 GND_LVDS LVDS Ground
15 RXE1+ LVDS signal of even channel 1(+)
16 RXE1- LVDS signal of even channel 1(-)
17 GND_LVDS LVDS Ground
18 RXE0+ LVDS signal of odd channel 0(+)
19 RXE0- LVDS signal of odd channel 0(-)
20 RXO3+ LVDS signal of odd channel 3(+)
21 RXO3- LVDS signal of odd channel 3(-)
22 RXOC+ LVDS signal of even channel clock (+)
23 RXOC- LVDS signal of even channel clock (-)
24 GND_LVDS LVDS Ground
25 RXO2+ LVDS signal of even channel 2(+)
26 RXO2- LVDS signal of even channel 2(-)
27 RXO1+ LVDS signal of even channel 1(+)
28 RXO1- LVDS signal of even channel 1(-)
29 RXO0+ LVDS signal of odd channel 0(+)
30 RXO0- LVDS signal of odd channel 0(-)
14
Downloaded from www.Manualslib.com manuals search engine
Service Manual
8. Key Parts Pin Assignments
U105(TSUMU58EHJ-LF-2)
15
Downloaded from www.Manualslib.com manuals search engine
Service Manual
16
Downloaded from www.Manualslib.com manuals search engine
Service Manual
17
Downloaded from www.Manualslib.com manuals search engine
Service Manual
18
Downloaded from www.Manualslib.com manuals search engine
Service Manual
8.3 U850 (LD7552B, PWM Power Controller)
Pin Symbol I/O Description
1 GND Ground
2 COMP I Voltage feedback pin(same as the COMP pin in
UC384X).By connecting a photo-coupler to close
the control loop and achieve the regulation.
3 VCC I Supply voltage pin
4 RT I This pin is to program the switching frequency. By
connecting a resistor to ground to set the switching
frequency.
5 NC Unconnected pin
6 CS I Unconnected pin
7 VCC I Supply voltage pin
8 OUT O Gate drive output to drive the external MOSFET
8.4 U1 (INL833, CCFL Inverter controller IC)
Pin Symbol I/O Description
1 VSEN I Voltage sense Feedback
2 SSTCMP I Capacitor for soft-star and loop
compensation
3 CT I Timing resistor and capacitor for operation
and striking frequency
4 RT1 I Timing resistor for striking frequency
5 GNDA Signal Ground
6 PDR2 O High side Driver output2
7 GNDP Power Ground
8 NDR2 O Low side Driver output2
9 NDR1 O Low side Driver output1
10 PDR1 O High side Driver output1
11 VDDA I Input power Pin
12 TIMER I Timing capacitor for Delay Timer
13 PWM I External PWM Dimming Input
14 ISEN I Current sense feedback
15 OVPT I Over-voltage protection threshold voltage
16 ENA I IC Enable/Disable
19
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 4- Disassembly & Assembly
1. Exploded Diagram
20
Downloaded from www.Manualslib.com manuals search engine
Service Manual
2. E2209WFPf Disassembly Block
22
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 5- TEST AND ADJUSTMENT
1. Function key Definitions
Menu
Enter
Power
Power Switch with power LED indicator Power: On/Off, includes power indicator and Power ICON
green- Active On
Amber- DPMS
Front Panel Controls 1- Input select: Select input signal
3- (): symbol molded into button, calls out brightness/Contrast, move down
the highlight bar.
1) Connect the VGA cable with the standard video pattern generator and
display the pattern with blackest and whitest colors.
2) Press “Power Key”, to power off the monitor.
3) Press “Menu Key” and “Up Key” simultaneously, and then press
“Power Key” to power on the monitor.
4) Press “Plus Key”, choose “Auto color” at bottom
5) Then execute Auto Color item.
6) After the “Auto Color Balance” process finished, go back to the
submenu of “Other Settings”, and press “Factory Reset” to exit
23
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Factory mode.
OSD Control
1st Level 2nd Level 3rd Level 4th Level 5th Level
Brightness
Contrast
Press √to adjust the screen
Auto Adjust(For VGA)
automatically
Auto Select
Input Source VGA
DVI-D
Input Color Format RGB YPbPr
Mode Selection Graphics Video
Preset Modes Standard
MultiMedia
Game
Warm
Cool
R
Custom(R,G,B) G
Color Settings B
Reset Color Settings
Horizontal Position
Vertical Position
Sharpness
Pixel Clock
Phase
Reset Display Settings
English
Español
Français
Language Deutsch
Português (Brasil)
简体中文
日本語
Other Settings Menu Transparency
Menu Timer
Menu Lock Lock Unlock
DDC/CI Enable Disable
LCD Conditioning Enable Disable
Factory Reset(Reset All
settings)
24
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Fig9
Fig10
25
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Burn In: Enable or disable the Burn-in mode by choosing ON or OFF.
Reset Timer: Reset the “Turn-on time” of the panel to 0H0M.
Color Temp: The R, G, B of Blue Preset (9300K), Red Preset (5700K) and Normal Preset (6500K) are generated
from scaling chip’s back-end white-balance program.
Time: Turn-on time of the panel.
DEBUG: Debug tool of scale IC U104.
Auto Color Balance (Automatically calibrate chip ADC parameter by using chip internal
DAC.)
5.1 If it is a new-built set, press “Auto/Plus” button to execute “Auto Color” at standard video pattern
5-MOSAIC pattern
5.2 Please confirm the following steps to perform “Auto Color Balance”:
- Connect the VGA cable with the standard video pattern generator and display 5-MOSAIC pattern on the
monitor.
- Press “Power” button to power off the monitor.
- Press “Menu” and “Auto/Plus” buttons simultaneously; then press “Power” button to power on the
monitor.
- Press “Plus Key”, select“Other Settings Menu” ,then Press “Plus Key”and choose factory at bottom
- Set BurnIn Mode item to ON, then execute Auto Color item.
- After the “Auto Color Balance” process finished, go back to “Other Settings Menu”, and press “Factory Reset” to exit Factory
mode
26
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Fig 11
After repair, to ensure the quality you should do the following test and adjustment.
27
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Item Content Equipment
Test OSD 1.Signal is set as 1680×1050@60Hz under General-1 Chroma
function 2. LCM button are from left to right, checking whether each Signal Generator
single function key and compound function key can be worked.
VGA cable When select VGA model and VGA cable is not plugged out, Visual check
detector self-test OSD will be floated.
Y measurement 1. Set brightness and contrast to default value 75 at 6500K Chroma Signal
at default setting 2. With full white pattern, Y shall be 220 20 cd/m2 Generator and Color
Analyzer
OSD Lock Test Soft Lock: When OSD is locked, this icon should appear for only Visual Inspection
2 seconds with all buttons pressed, except for the “Menu” and
“Power” ones.
Hard Lock: Press “Menu” button for 15 seconds enables the
“locked” icon to be displayed, which will lock All buttons
expect for the “Power”. Press “Menu” button for another 15
seconds enables the “unlock” icon to be shown.
Panel Flicker 1. Mode:1680×1050@60Hz Equipment::
check 2. Set Brightness& Contrast to default value (75%) Chroma Signal
3. Do “Auto Adjustment” Generator & PC
4. Shut down PC to check whether there’s flicker on the
center of the picture.
Power saving 1. Mode:1680×1050@60Hz Chroma signal
2. Pattern: full Black generator and
3. Brightness: Max. Power meter
4. Contrast: Default AC input:230V/50Hz
5. Check power consumption at each modes
State Power Consumption LED color
Normal(with full
<46W blue
load)
Stand By <2W amber
Power Key Off
<1W no
28
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 6- TROUBLE SHOOTING
Common Acknowledge
If you change the M/B, be sure that the U101,U102 and U105 these three components also changed to
the new M/B because there was program inside. If not, please re-write EDID or upload firmware into
serial flash(U105) via VGA Cable. How to do please refer to the Page 19.
If you adjust clock and phase, please do it at condition of Windows shut down pattern.
Please confirm the R/G/B color under 32gray scale pattern.
This LCM is analog interface. So if the entire screen is an abnormal color that means the problem
happen in the analog circuit part, if only some scale appears abnormal color that stand the problem
happen in the digital circuit part.
If you check the H/V position, please use the crosshatch pattern.
This LCM support 10 timing modes, if the input timing mode is out of specification, “Cannot Display
this Video Mode” will be displayed on the screen.
If brightness uneven, repairs Inverter circuit or change a new panel.
If you find the vertical line or horizontal line lost on the screen, please change panel.
If the self-test pattern is moving on the screen, please check whether VGA Cable is plugged in the
Monitor or PC if select analog model on OSD or check whether DVI Cable is plugged in the Monitor
or PC if select DVI model on OSD . If the VGA or DVI Cable is plugged in well, please change
another VGA or DVI cable.
No Power and LED Off
Is there DC24V output
Is there DC5V at L854;
NO
YES NO
Check RT850, F850
YES NO
Check D852, D851
YES
Check Q850
29
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Power(include IF +5Vand +3.3V) supply normal but LED off and
no display
Is the key function OK? Yes Press power key to DC on the monitor,
if display ok the process is end, if no
NO display see the no backlight process
Yes
NO Change C164
Is the low active reset signal at #108 of
IF Board U105 normal?
NO
Yes
Upgrade Firmware to Serial Flash U108
by VGA port with ISP_ Tool V4.100.exe
END
Yes
yes
Is R165 open? Change R165
NO
NO
Is Q107 work normal? Change Q107
Yes
Is theLED control signal at 123# of U105
NO Change U105
high-low convertible when DC on/off
END
30
Downloaded from www.Manualslib.com manuals search engine
Service Manual
YES
NO
Do the Hsync. & Vsync. Signals exist Insert VGA Cable correctly
in CN102 #13& #14 separately when
select VGA mode by OSD?
YES
YES
YES
YES
Is theLED control signal at 4# of
U105 high-low convertible when DC Change U105
NO
on/off
END
31
Downloaded from www.Manualslib.com manuals search engine
Service Manual
No backlight
Yes
No No power supply to Yes Check the cable that from I/F
LED lamp is OK inverter BD to P/I BD is ok
Yes
Yes
Yes
Yes
Vsense voltage is 2.9V Lamp connector opened
No
Yes
Yes Yes
Pin14 of U1 Voltage Check R21,R22,C10
is Low Level Feedback circuit failure
Yes Yes
Pin6&10 of U1 voltage is U1 protected Check ZD1, R1 , ZD2, R2, C12, C13
high level voltage
Yes
END
32
Downloaded from www.Manualslib.com manuals search engine
Service Manual
5. Backlight on, key function and LED accurate indication ok but
no picture
YES
YES
IS the display is white and cannot Check DC 5.0V on NO Is the panel enable
display OSD when press key? CN103#1, #2, #3 signal at 73# of
U105,if no check
Q104 circuit or change
NO U105,if yes Check
Q101 circuit
VGA
Is display selftest picture at Is there RGB signal in NO
VGA mode or DVI mode? U104 #28, #25 #23? Change D103,
D104 & D105
DVI
Yes
Is there DVI signal in U105 #9, YES Are there data output on YES Is the FFC cable
#10,#12,#13,#15,#16,#18 #19? U105#77~#86 inserting ok,if no
#91~#100 reinsert else
change FFC cable
No
Change U105
Change D202, D203, D204,
D205, D206, D207, D208,
D209
END
33
Downloaded from www.Manualslib.com manuals search engine
Service Manual
6.At 32-gray scale pattern, color lost in some scale
OK,
Re-insert the FFC Cable END
NO
OK,
Change FFC Cable END
NO
Change U105
34
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Chapter 7- RECOMMENDED PART LIST
Content PN Description Supplier Usage
35
Downloaded from www.Manualslib.com manuals search engine
Service Manual
ATTACHMENT 1- Bill of Material
1. Interface board BOM
2E+07
ITEM P/N Description Supplier Usage Location
791701300B00R PCBA,I/F BOARD W/O SPK,LE22F4-B12 ROHS
10 629030018710R PROGRAM,W/O SPK LE22F4-B12 ROHS 1
20 791701320600R PCBA,I/F BOARD,MI,W/O SPK,LE22F4-612 ROH 1
30 791701340600R PCBA,I/F BOARD,SMT,W/O SPK,LE22F4-612 RO 1
40 511130001200R SOLDER BAR,Sn96.5/Ag3.0/Cu0.5/Ni0.06/Ge0 TOMAS, 2.2
50 641120000010R HDCP RECEIVE DEVICE KEY DCP LLC, 1
LABEL,BARCODE,BLANK,33x7mm, ROHS,FOR
60 506140005700R HENGMINGDA,JIAYINMEI,KAIDA, 1
PCB
2E+07
ITEM P/N Description Supplier Usage Location
791701320600R PCBA,I/F BOARD,MI,W/O SPK,LE22F4-612 ROH
10 430631080170R WFR 8P 2.0MM 180° W/LOCK ROHS CVILUX,FOXCONN,JOWLE, 1 CN101,
20 440819015030R CON D-SUB FEM.15P RA W/O SCREW DZ11AA1-H CVILUX,DLK,FOXCONN,JOWLE,TEKCON,ZJGHJ, 1 CN102,
30 430631080180R WFR 2X4P 2.0MM 180° W/LOCK ROHS CVILUX,FOXCONN, 1 CN104,
40 443842024060R CON DVI-D RA 24+1P FEM.W/O SCR EW QH1112 DLK,FOXCONN,ZJGHJ, 1 CN201,
50 432008010270R XTAL 14.31818MHz HC-49US DIP 16pF 30PPM HUAN MOUN,TXC,ZGC, 1 X101,
60 420271010460R CAP SE 100uF 16V M,105℃ ST,6.3*11 ROHS SAMXON,SU'SCON,TEAPO, 2 C109,C102,
70 420432200460R CAP EC 22uF 16V M,105℃ ST, 5x11,RoHS ELITE,LELON,SAMXON,SU'SCON,TEAPO, 3 C103,C142,C150,
2E+07
ITEM P/N Description Supplier Usage Location
791701340600R PCBA,I/F BOARD,SMT,W/O SPK,LE22F4-612 RO
10 444099030040R CON, SMD 1.0MM 30PIN with lock RoHS CVILUX,P-TWO, 1 CN103,
C106,C108,C110,C126,C128,C133,C134,C135,C136,
C137,C138,C139,C140,C141,C143,C144,C145,C146,
C147,C149,C153,C154,C155,C156,C159,C160,C161,
20 419351044010R C SMD(0402) X5R 0.1uF/16V K,RoHS DARFON,WALSIN,YAGEO, 53
C165,C167,C168,C169,C170,C171,C172,C173,C201,
C202,C213,C111,C122,C123,C124,C125,C203,C204,
C205,C206,C207,C208,C209,C210,C211,C212,
R102,R129,R140,R150,R151,R152,R166,R169,R171,
170 414918010350R RES SMD (0402) 10KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 24 R172,R174,R176,R177,R178,R179,R180,R190,R192,
R213,R217,R103,R220,R184,R161,
36
Downloaded from www.Manualslib.com manuals search engine
Service Manual
320 412000435481R IC AT24C02BN-SH-T 2K SOIC8(ATMEL)RoHS ATMEL, 2 U103,U201,
320 412000480280R IC M24C02-RMN6TP SO8(ST)RoHS ST, 0
320 412000480990R IC CAT24C02WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
330 412000653060R IC TSUMU58EHJ-LF-2 PQFP128(MSTAR)Rohs MSTAR, 1 U105,
340 412000224482R IC AT24C16BN-SH-T 16K(ATMEL) SOIC 8 ROHS ATMEL, 1 U106,
340 412000224280R IC M24C16-WMN6TP SO8 16K (ST) ROHS ST, 0
340 412000481990R IC CAT24C16WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
350 412000494190R IC SST25LF020A-33-4C-SAE SOIC8(SST)ROHS SST, 1 U108,
350 412000494310R IC PM25LV020-100SCE SOIC8(PMC)RoHS PMC, 0
ZD102,ZD103,ZD104,ZD105,ZD106,ZD201,
360 411130962950R ZENER 6.2V MMSZ5234B SOD-123(PANJIT)RoH PANJIT, 9
ZD203,ZD204,ZD107,
360 411121462950R ZENER 6.2V BZT52-C6V2 SOD-123(WILLAS)ROH WILLAS, 0
360 411131562950R ZENER 6.2V BZT52C6V2-7-F SOD-123(DIODES) DIODES, 0
370 491351300100H PCB I/F BOARD LE19H0 TIP TOP,WELFARE, 1
380 414916056150R RES SMD (0603) 560Ω J,RT RoHS REV:A TA-I,WALSIN,YAGEO, 1 R168,
CHILISIN,DARFON,EASYMAGNET,
160 425000010530R COIL CHK 5uH 7.8X10 CHK-053 0 181085R0L 2 L854,L856,
FOXCONN,FRONTIER,TAICHANG,
37
Downloaded from www.Manualslib.com manuals search engine
Service Manual
FERR BEAD
280 432002200190R CHILISIN,TAI-TECH, 2 L857,L858,
3.5x9x0.65,VT,RoHS,RH03509ST-B
290 511130001200R SOLDER BAR,Sn96.5/Ag3.0/Cu0.5/Ni0.06/Ge0 TOMAS, 8.2
300 511110000103R HOT-MELT ADHESIVES,UB-618 U-BOND, 1.45
300 511110000101R HOT-MELT ADHESIVES (#526) EXCELSTAR, 0
310 511110000501R SILICONE RTV RUBBER,UB-511(EURO) EURO, 0.45
38
Downloaded from www.Manualslib.com manuals search engine
Service Manual
220 414908100910R RES SMD(0805)10Ω F,RT ROHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R856,R7,
240 414908330110R RES SMD (0805) 3.3KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 1 R868,
250 414908039250R RES SMD (0805) 3.9KΩ J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R872,
270 411023004021R DIO SN4148-LF 75V/0.15A SMD 1206 (FEC)Ro FRONTIER, 1 D841,
270 411020046090R DIO 1N4148W 75V/0.15A(PEC)RoHS SOD-123 PANJIT, 0
DIO 1N4148W-F 75V/0.15A(DIODES
270 411020046310R DIODES, 0
RoHS,SOD-
280 411020068020R DIO BAW56 70V SOT-23(FRONTIER)RoHS FRONTIER, 1 ZD1,
280 411020068090R DIO BAW56 75V SOT-23(PANJIT)RoHS PANJIT, 0
280 411020068210R DIO BAW56 85V SOT-23(PHILIPS)RoHS PHILIPS, 0
290 411020047020R DIO BAV70-LF, 70V SOT-23(FEC) ROHS FRONTIER, 2 ZD2,ZD3,
290 411020047210R DIO BAV70 85V SOT23 (PHILIPS) RoHS PHILIPS, 0
290 411020047090R DIO BAV70, 70V SOT-23(PEC) ROHS PANJIT, 0
ZENER 5.6V 0.5W BZT52C5V6-F,SO
300 411131556950R DIODES, 2 ZD4,ZD5,
D123(DIOD
ZENER 5.6V BZT52-C5V6
300 411121456950R WILLAS, 0
SOD-123(WILLAS)ROH
ZENER 5.6V 0.41W BZT52-C5V6,SO
300 411120956950R PANJIT, 0
D123(PANJ
310 411020026210R DIO BAV99 350mW 70V SOT-23(PHI RoHS PHILIPS, 2 ZD6,ZD7,
310 411020026390R DIO BAV99,SOT-23(INFINEON)RoHS INFINEON, 0
310 411020026090R DIO BAV99 350mW 75V SOT-23(PEC RoHS PANJIT, 0
DIO BAV99-LF 350mW 70V SOT-23
310 411020026020R FRONTIER, 0
(FEC)RoHS
320 410080003290R XSTR AP4575GM N&P SO-8(APEC)ROHS AP, 2 Q6,Q7,
XSTR P5506NVG N&P
320 410080003430R NIKO, 0
SOP-8(NIKO-SEM)ROHS
XSTR MMBT4401 NPN
330 410070010240R FAIRCHILD, 1 Q851,
SOT23(FAIRCHILD)RoHS
330 410070010420R XSTR MMBT4401 NPN SOT23(PANJIT)RoHS PANJIT, 0
330 410070010210R XSTR PMBT4401 NPN SOT23(PHILIPS)RoHS PHILIPS, 0
340 412000628810R IC LD7552BPS SOP8(Leadtrend)ROHS LEADTREND, 1 U850,
350 412000654630R IC INL833GN SOP16(O2 MICRO)Rohs O2, 1 U1,
360 791701410600R PCBA,PWR&INV./B,AI,LE22F4-612 ROHS 1
39
Downloaded from www.Manualslib.com manuals search engine
Service Manual
50 411130930010R ZENER 30V GDZ30A DO35(PANJIT)RoHS PANJIT, 0
60 430613050100R FUSE SLOW PICO II 5A/125V U/C,AT,ROHS LITTELFUSE, 1 F851,
60 430613050101R FUSE SLOW 5A/125V U/C,AT,ROHS WALTER, 0
70 491571400100H PCB,P/I ,1/OSP /CEM1/16,LE22F4-612 HSIANGKUO,TAT CHUN, 1
80 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 7.5MM HOTRON,YUANYE, 400 J1,J2,J5,J11,J12,J13,J14,J15,
80 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 7.5MM HOTRON,YUANYE, 0
90 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 10MM HOTRON,YUANYE, 200 J3,J6,J7,J4,
90 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 10MM HOTRON,YUANYE, 0
100 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 15MM HOTRON,YUANYE, 100 J9,J10,
100 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 15MM HOTRON,YUANYE, 0
110 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 12.5MM HOTRON,YUANYE, 150 J8,J16,J17,
110 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 12.5MM HOTRON,YUANYE, 0
130 411020080020R DIO P6KE170A-LF 600W/100A DO-15(FEC) FRONTIER, 1 D853,
130 411020080460R DIO P6KE170A 600W/100A DO-15(SECOS) SECOS, 0
130 411020080090R DIO P6KE170A 600W/100A DO-15(PANJIT)PANJIT, 0
140 415222700140R RES MF 1/4W 270Ω F,AT,MINI,RoHS QUEENMAO,TZAI YUAN, 1 R857,
150 415215101140R RES MF 1/8W 5.1KΩ F,AT,RoHS QUEENMAO,TZAI YUAN, 2 R11,R25,
LABEL,BARCODE,BLANK,33x7mm,
160 506140005700R HENGMINGDA,JIAYINMEI,KAIDA, 1
ROHS,FOR PCB
40
Downloaded from www.Manualslib.com manuals search engine
Service Manual
10 411070094500R A LED SMD YB HTL-19-22UYUBC/TR8(HongTong)R HONGTONG, 0
4.Assembly BOM
20080403
ITEM Phant.item P/N Description Supplier Usage Un Revision
8221F4B1D010R LE22F4-B12(B)W/O SPK,US(DAO/E2209Wf)
10 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx FOXCONN,I-SHENG, 1 PC C
FOXCONN,GREATLANE,HOTRON,JVE,
20 453010100320R CABLE D-SUB 15P MALE 6FT BLACK/BLUE AB 8 廣宇, 1 PC B
30 453030300440R CABLE DVI-D 18+1P MALE 1.8M BLACK ROHS FOXCONN,HOTRON,JVE,廣宇, 1 PC A
40 x 713100005300R ASSY, PACKAGE, PACK, DAO, LE22F4 1 PC A
50 x 714070EB0000R ASSY,FINAL(B)W/O SPK,LE22F4-B12(E2209Wf) 1 PC A
20080329
ITEM Phant.item P/N Description Supplier Usage Un Revision
713100005300R ASSY, PACKAGE, PACK, DAO, LE22F4 A
10 506250022800R LABEL,ID(LH), LE22F4 HENGMINGDA,高綺, 1 PC A
20 506250022802R LABEL,AGENCY, LE22F4 HENGMINGDA,高綺, 1 PC A
30 506431005200R FILM,SCREEN,PROTECTION,PRINTED,LE22E0 柏興,鴻旺, 1 PC A
40 506380001400R TAPE 3M-897 12x45000mm 久威,矽威, 0.00333 ROL A
50 506280007601R POSTER,QUICK SETUP,WEST, LE22F4 裕同,鴻達, 1 PC A
60 703500005700R KIT,ACCESSORY, DOC, DAO, LE22F4 裕同,鴻達, 1 PC A
70 506120300060R BAG, PLASTIC,L670*W440mm(PRINTED), LE22E 柏興,鴻旺, 1 PC A
80 506120007000R BAG PLASTIC L480xW610xT0.05mm(PRINTED) 柏興,鴻旺, 1 PC A
90 506020025000R CARTON,DELL(WWW), LE22F4 佳藝,美盈森, 1 PC A
100 506060010300R cushion-top,LE22F4 東揚, 1 PC A
110 506060010310R cushion-bottom,LE22F4 東揚, 1 PC A
120 506340004700R LABEL BLANK 101X50mm DELL EMEA CARTON 高綺,鍵升, 1 PC A
130 506380002622R TAPE, WRAPPING TYPE PRINTED(DELL), BLACK 佳普森, 0.00156 ROL A
140 x 713010000901R ASSY PACK,40STD,LE22F4 1 PC A
140 x 713010000900R ASSY PACK,20STD,LE22F4 0 PC A
140 x 713010000903R ASSY PACK,AIR CARGO(20STD),LE22F4 0 PC A
140 x 713010000904R ASSY PACK,AIRCARGO(40STD),LE22F4 0 PC A
140 x 713010000905R ASSY PACK,AIR CARGO(40H),LE22F4 0 PC A
20080403
ITEM Phant.item P/N Description Supplier Usage Un Revision
714070EB0000R ASSY,FINAL(B)W/O SPK,LE22F4-B12(E2209Wf) A
10 509212103500R SCREW,F,CROSS,T.T-2*3,BLK 高億, 4 PC A
20 509116610510R SCREW,P,CROSS,M4*10,BLACK-NL(NYLOK) 立侑,高億, 4 PC A
30 714020014700R stand-assy,LE22F4 CJC,富鴻齊, 1 PC A
40 714030018000R front-bezel-assy,LE22F4 MMP, 1 PC A
50 714050016900R back-cover-assy,LE22F4 MMP, 1 PC A
60 x 714080EB0000R ASSY,PANEL,W/O SPK,LE22F4-B12(E2209Wf) 1 PC A
20080329
ITEM Phant.item P/N Description Supplier Usage Un Revision
713010000900R ASSY PACK,20STD,LE22F4 A
10 506432003700R SLIP SHEET,L1192xW898xH75mm, LE22F4 SUNSTREAM, 0 PC A
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0 PC A
30 506039008800R CORNER PAPER 1060x50x50xT3mm LE1963 佳藝, 0 PC A
40 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0 ROL A
50 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0 PC A
60 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0 ROL A
20080329
ITEM Phant.item P/N Description Supplier Usage Un Revision
713010000901R ASSY PACK,40STD,LE22F4 A
10 506432003700R SLIP SHEET,L1192xW898xH75mm, LE22F4 SUNSTREAM, 0.05 PC A
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0.1 PC A
30 506039008800R CORNER PAPER 1060x50x50xT3mm LE1963 佳藝, 0.2 PC A
40 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0.00209 ROL A
50 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0.00435 PC A
60 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0.00071 ROL A
20080329
ITEM Phant.item P/N Description Supplier Usage Un Revision
41
Downloaded from www.Manualslib.com manuals search engine
Service Manual
713010000903R ASSY PACK,AIR CARGO(20STD),LE22F4 A
10 506150006900R PALLET L1284xW914xH120mm LE1746 實習工廠, 0 PC B
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0 PC A
30 506039005410R CORNER PAPER 800x50x50xT3mm LE1718 佳藝, 0 PC A
40 506039001400R CORNER PAPER 200x50x50mm ROHS 佳藝,金惠, 0 PC A
50 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0 ROL A
60 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0 PC A
70 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0 ROL A
20080329
ITEM Phant.item P/N Description Supplier Usage Un Revision
713010000904R ASSY PACK,AIRCARGO(40STD),LE22F4 A
10 506150006900R PALLET L1284xW914xH120mm LE1746 實習工廠, 0 PC B
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0 PC A
30 506039005410R CORNER PAPER 800x50x50xT3mm LE1718 佳藝, 0 PC A
40 506039001400R CORNER PAPER 200x50x50mm ROHS 佳藝,金惠, 0 PC A
50 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0 ROL A
60 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0 PC A
70 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0 ROL A
20080329
ITEM Phant.item P/N Description Supplier Usage Un Revision
713010000905R ASSY PACK,AIR CARGO(40H),LE22F4 A
10 506150006900R PALLET L1284xW914xH120mm LE1746 實習工廠, 0 PC B
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0 PC A
30 506039000101R CORNER PAPER 1000x50x50xT3mmLE1711 佳藝,金惠, 0 PC A
40 506039001400R CORNER PAPER 200x50x50mm ROHS 佳藝,金惠, 0 PC A
50 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0 ROL A
60 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0 PC A
70 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0 ROL A
20080403
ITEM Phant.item P/N Description Supplier Usage Un Revision
714080EB0000R ASSY,PANEL,W/O SPK,LE22F4-B12(E2209Wf) A
10 631102220480RD LCP 22" LTM220M1-L01-CTB(A)(SAMSUNG)ROHS 1 PC A
10 631102220490RD LCP 22" LTM220M1-L01-CUB(A)(SAMSUNG)ROHS 0 PC A
20 701000009400R ASSY,CHASSIS,V,LE19F6 MMP, 1 PC A
30 501110200400R LOGO PLATE DELL UX383 LE1963 DEMETER, 1 PC A
40 509000001000R BOLT,#4-40x12.5,Ni ROHS 高億, 4 PC A
50 509016305200R SCREW,I,CROSS,M3*5,Zn-Cc 高億, 4 PC A
60 509016306200R SCREW,I,CROSS,M3*6,Zn-Cc 高億, 2 PC A
70 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 立侑,高億, 4 PC A
80 509476606200R SCREW,B,CROSS W/W(T)M3*8,ZnROHS 高億,鴻益進, 1 PC A
90 791701300B00R PCBA,I/F BOARD W/O SPK,LE22F4-B12 ROHS 1 PC
100 791701400600R PCBA,P/I BOARD W/O SPK,LE22F4-612 ROHS 1 PC
110 791701500000R PCBA,KEYPAD BOARD LE22F4-612 ROHS 1 PC
120 430303001730R HRN LVDS FFC 30P 181mm FOXCONN,P-TWO, 1 PC A
130 430300801950R HRN ASSY 2x4P to 8P 405mm UL1571#28 FOXCONN,JVE, 1 PC
Attachment 2- Schematic
1. Interface board schematic
42
Downloaded from www.Manualslib.com manuals search engine
Service Manual
43
Downloaded from www.Manualslib.com manuals search engine
Service Manual
44
Downloaded from www.Manualslib.com manuals search engine
Service Manual
45
Downloaded from www.Manualslib.com manuals search engine
Service Manual
46
Downloaded from www.Manualslib.com manuals search engine
Service Manual
47
Downloaded from www.Manualslib.com manuals search engine
Service Manual
48
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Attachment 3- PCB Layout power/inverter bd:
power/inverter board:
Top Layer
49
Downloaded from www.Manualslib.com manuals search engine
Service Manual
Bottom Layer
50
Downloaded from www.Manualslib.com manuals search engine