National Electrical Code®
National Electrical Code®
Informational Note No. 1: Appliances used within the recreational vehicle can create leakage
current levels at the supply receptacle(s) that could exceed the limits of a Class A GFCI device.
Informational Note No. 2: The definition of Power-Supply Assembly in 551.2 and the definition of
Feeder in Article 100 clarifies that the power supply cord to a recreational vehicle is considered a
feeder.
Substantiation:
The 2017 NEC included changes in Section 210.8 and CMP 7 did not have the opportunity to
review and Correlate with Article 551 concerning the requirement of GFCI protection on 30- and
50- ampere receptacles in RV site equipment. This has introduced ambiguity about the
application of 2017 NEC Section 210.8 new GFCI requirements with respect to 30- and 50-
ampere receptacles supplying RV’s. In numerous cases where the 2017 Code is in use debate has
surfaced as to the applicability of the 210.8 requirements and has caused projects to be cancelled
or shut down as a result.
During the 2020 Code cycle CMP 7 addressed the issue during both the First and Second Draft
sessions. The panel, by votes of over 80% in both cases, determined that Section 210
requirements do not apply to the 30- and 50- ampere receptacles as these are considered feeders
per the definition of a feeder in Article 100 and the definition of a Power Supply Assembly at
Section 551.2. Furthermore, if GFCI protection were to be placed on the 30- and 50- ampere
feeders the accumulative allowed GFCI leakage may exceed the limits of a Class A GFCI device.
This TIA seeks to return to Section 551.71 language contained in SCR 30 created by the NEC
Correlating Committee with an additional sentence reinforcing the Feeder – Power Supply
Assembly relationship of the 30- and 50- ampere power in RV Site Equipment.
By accepting the TIA the Code will be relieved of the ambiguous Code language and
unnecessary GFCI protection of feeders. Of further concern is of the actions that users would
perform to keep power on a circuit if a 30- or 50- amp device were to trip on GFCI. A common
action is to clip off the ground pin on the feeder cord to the RV.
Further, waiting for the 2023 cycle keeps the ambiguity and potentially unenforceable nature of
the 2017 Code in place for another three years.
Additionally, lost in the reverting back to the 2017 NEC language for the 2020 Code making
process was an editorial move to 551.71(A) during the First Draft of the requirement for the 20
ampere receptacles to be weather resistant.
Emergency Nature: The NFPA Standard contains a conflict within the NFPA Standards or
within another NFPA Standard. The proposed TIA intends to correct a circumstance in which
the revised NFPA Standard has resulted in an adverse impact on a product or method that was
inadvertently overlooked in the total revision process or was without adequate technical (safety)
justification of the action.
The emergency nature of this TIA is to fix serious correlation issues that would exist for the
Code user whether you are an installer or enforcer. Due to the results of the rejection of CAM70-
36 by CMP-7; and the reversion of 551.71(F) to 2017 Code Language; an inconsistency now
exists with other Special Occupancies in Chapter 5. CMP-7 is still under the impression that the
result of the rejection of CAM 70-36 should have resulted in reverting back to First Draft
language (last point of consensus) rather than reverting back to 2017 NEC text.
This TIA is to adopt the language that was approved by CMP-7and the Coordinating Committee
during their meetings for the 2020 NEC.
In all of the other Articles that are under the purview of CMP-7 where a power supply cord is
used, the supply cord is considered a feeder and there are no requirements for Class A GFCI
protection. Feeder conductors being extended to a marina-receptacles need to be protected at the
100 mA level, but this is ground-fault protection (GFP) of equipment, not Class A GFCI
protection.
From the outset of the 2020 NEC revision cycle, the goal of CMP-7 was to remove the wide
interpretation of 551.71(F) that existed in the 2017 NEC as a result of the then new requirements
of 210.8(B). Without this TIA, we are right back to square one with inconsistent interpretation at
551.71(F).
Consider other Articles under CMP-7 purview: All of the reference NEC sections below
would allow a cord and plug assembly without Class A GFCI protection.
545.22 Power Supply (A) Feeder. The feeder shall include four insulated color-coded
conductors, one of which shall be an equipment grounding conductor. The equipment grounding
conductor shall be permitted to be uninsulated if part of a cable assembly.
Informational Note: For temporary installation of feeder conductors see Article 590.
550.2 Feeder Assembly. The overhead or under-chassis feeder conductors, including the
grounding conductor, together with the necessary fittings and equipment or a power-supply cord
listed for mobile home use, identified for the delivery of energy from the source of electrical
supply to the panelboard within the mobile home.
550.10 Power Supply. (A) Feeder. The power supply to the mobile home shall be a feeder
assembly consisting of not more than one listed 50-ampere mobile home power-supply cord or a
permanently installed feeder.
552.43 Power Supply. (A) Feeder. The power supply to the park trailer shall be a feeder
assembly consisting of not more than one listed 30-ampere or 50-ampere park trailer power-
supply cord, with an integrally molded or securely attached cap, or a permanently installed
feeder.
In all of these examples, the Code language clearly states that these power-supply cords are
feeders and were never intended to have Class A GFCI protection. CMP-7 was very diligent and
intentional with treating the installation in an RV Park the same. As determined by our
predecessors on CMP-19, and now CMP-7, the installation of these conductors would be
installed as a feeder as defined in Article 100, and not treated differently between the articles.
Finally, a change in the 2017 Code Language was not coordinated with (then) CMP-19 (now
CMP-7) to allow this technical committee to insert language modifying or amending 210.8(B)
for RV Site Equipment. CMP-19 should have had the option to either assert our ability to Modify
or Amend 551.71 or to clarify that the 30- and 50- amp circuits are in fact feeders according to
Article 100 and supported by 551.2 (Power Supply Assemblies) during the 2017 cycle.
Anyone may submit a comment by the closing date indicated above. Please identify the TIA number and
forward to the Secretary, Standards Council. SUBMIT A COMMENT