ISD700

Directional/Fixed Antenna
(Passive)
Installation Guide

Suitable for IsatDocks

Support: [email protected]

Web: www.beamcommunications.com
Info: [email protected]

BEAM Communications Pty Ltd

www.beamcommunications.com

Victoria, 3170, AUSTRALIA

8 Anzed Court, Mulgrave
Fax: +61 3 9560 9055
Tel: +61 3 8588 4500

PART #: USRMAN006502
Antenna Coverage
0° N 0° 20° N 0° N
A 40° B C 30°
Point SW W E Point SE W E Point NE W E
90° 90° 90°
40° approx. 20° approx. 30° approx.
S S S
90° approx. 90° approx. 90° approx.
60° approx. 60° approx. 60° approx.
45° approx. 45° approx. 45° approx.
90° approx. N N N
30° approx. 30° approx. 30° approx.
×A
20° approx. 20° approx. 20° approx.
×B
45° approx.
E W E W E W
25° approx.
×C
0° approx.
S S S
180° 160° 140° 120° 100° 80° 60° 40° 20° 0° 20° 40° 60° 80° 100° 120° 140° 160° 180°
I-4 Americas I-4 EMEA I-4 Asia-Pacific Sourced from Inmarsat
inmarsat.com
Directional/Fixed Antenna Installation Guide Installation Guidelines Installation Options
To ensure maximum performance of the antenna system and to The antenna system is suitable for stationary and fixed
Step One: Option B maximise availability and reliability of service the antenna must; applications and is designed to meet Inmarsat System
• have a clear line of site to the sky performance requirements when installed according to the
Place the mounting arm in the mounting swivel and use a Fixing the antenna swivel to a 90° surface. instructions in this guide.
hex allen key to tighten the two grub screws. • be clear and free of obstructions
The following figure shows typical Installations:
• be clear of metal objects
• be located away from other transmitting devices
• be securely affixed in location
• not be located indoors
Option C • be installed in conjunction with a certified cable
Fixing the antenna swivel to a pole. Installing Antenna Cables
When installing antenna cables, follow these guidelines:
• Route and restrain cables to prevent them from vibrating
or moving under normal conditions, which could result in
damage to the antenna or the coaxial cable connections.
• Wherever the cables contact structures, protect the
cables from chafing or abrasion. If a cable needs to be
Step Two: Step Four: bent, avoid kinking it, and ensure that each bend radius
Place the Antenna on the mounting arm and hold in place. There is a label on the underside of the antenna which follows the cable supplier limits.
Use the hex bolt and split washer to attach the antenna to indicates “THIS SIDE UP” . Ensure when fitting the antenna in • Use coaxial sealant, shrink‐wrap tubing, electrical tape,
the mounting arm and loosely screw them together with the desired location that this label is facing the sky. or another suitable product to seal all cable connections
the hex allankey provided. appropriately to prevent moisture and corrosion damage
from weather exposure. The antenna must be installed without obstruction of other
instruments or structures. The antenna must not be positioned
• Mount all antennas clear of nearby metal obstructions. within range of radar equipment or other RF interference.
THIS SIDE UP

Directional/Fixed Antenna Kit Contents

THIS SIDE UP

1. Directional/Fixed Antenna
2. 2 x U Bolts 1 9

3. 4 x Large Flat Washers

4. 4 x Nuts
Step Three: Step Five:
5. Screw with Hex
You have a number of options for fitting the antenna in position. One the mounting swivel has been fitted in the correct
6. Split Washer
position the incline angle of the antenna will need to be
secured. On the inside of the mounting arm is another hex 7. Mounting Bracket 2
Option A grub screw. Once the antenna has been put on the correct 10
8. Mounting Pole
Fixing the antenna swivel to a flat surface. incline position, tighten the grub screw to hold the antenna
9. Underside of antenna showing
position in place.
antenna and GPS connections.
3
10. Allen Key
4

5
6
7

NOTE:
For Satellite & GPS connection instructions please consult your Beam Inmarsat Product manual.