PARTYBOX 100

OWNER’S MANUAL
 Caution FCC and IC statement for users (USA and Canada
IMPORTANT SAFETY INSTRUCTIONS only)
This device complies with part 15 of the FCC Rules. Operation
For all products: is subject to the following two conditions: (1) This device may
1. Read these instructions. not cause harmful interference, and (2) this device must accept
2. Keep these instructions. any interference received, including interference that may cause
3. Heed all warnings. undesired operation.
4. Follow all instructions. CAN ICES-3(B)/NMB-3(B)
5. Do not block any ventilation openings. Install this apparatus
in accordance with the manufacturer’s instructions. Federal Communication Commission
6. Do not install this apparatus near any heat sources such as Interference Statement
radiators, heat registers, stoves or other apparatus (including
This equipment has been tested and found to comply with the limits
amplifiers) that produce heat.
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
7. Do not defeat the safety purpose of the polarized or grounding- These limits are designed to provide reasonable protection against
type plug. A polarized plug has two blades with one wider harmful interference in a residential installation. This equipment
than the other. A grounding-type plug has two blades and generates, uses and can radiate radio frequency energy and, if
a third grounding prong. The wide blade or the third prong not installed and used in accordance with the instructions, may
is provided for your safety. If the provided plug does not fit cause harmful interference to radio communications. However,
into your outlet, consult an electrician for replacement of the there is no guarantee that interference will not occur in a particular
obsolete outlet. installation. If this equipment does cause harmful interference to
8. Protect the power cord from being walked on or pinched, radio or television reception, which can be determined by turning
particularly at plugs, convenience receptacles and the point the equipment off and on, the user is encouraged to try to correct
where they exit from the apparatus. the interference by one or more of the following measures:
9. Use only attachments/accessories specified by the • Reorient or relocate the receiving antenna.
manufacturer. • Increase the separation between the equipment and receiver.
10. Use only with the cart, stand, tripod, bracket or • Connect the equipment into an outlet on a circuit different
table specified by the manufacturer or sold with from that to which the receiver is connected.
the apparatus. When a cart is used, use caution
• Consult the dealer or an experienced radio/TV technician for
when moving the cart/apparatus combination
help.
to avoid injury from tip-over.
11. Unplug this apparatus during lightning storms or when Caution: Changes or modifications not expressly approved
unused for long periods of time. by HARMAN could void the user’s authority to operate the
12. To disconnect this apparatus from the AC mains completely, equipment.
disconnect the power-supply cord plug from the AC
receptacle. For Products That Transmit RF Energy
13. The mains plug of the power-supply cord shall remain readily
FCC AND IC INFORMATION FOR USERS
operable.
This device complies with Part 15 of the FCC rules and Industry
14. Do not expose batteries to excessive heat such as sunshine,
Canada license-exempt RSS standard(s). Operation is subject
fire or the like.
to the following two conditions: (1) This device may not cause
15. This apparatus is intended to be used only with the power harmful interference; and (2) this device must accept any
supply and/or charging cable provided by the manufacturer. interference received, including interference that may cause
undesired operation.
FCC/IC Radiation Exposure Statement
This equipment complies with FCC/IC RSS-102 radiation
exposure limits set forth for an uncontrolled environment.
FCC Caution:
High power radars are allocated as primary users of the 5.25 to
5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations
can cause interference with and/or damage this device. No
configuration controls are provided for this wireless equipment
allowing any change in the frequency of operations outside the
FCC grant of authorization for US operation according to Part
15.407 of the FCC rules.
IC Caution:
User should also be advised that:
(i) The device for operation in the band 5150-5250 MHz is only
for indoor use to reduce the potential for harmful interference to

2
 English
co-channel mobile satellite systems; (ii) the maximum antenna FOR ALL EU COUNTRIES
gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall comply with the e.i.r.p. Limit: and (iii) For products that include audio out
The maximum antenna gain permitted for devices in the band Prevention of hearing loss
5725-5825 MHz shall comply with the e.i.r.p. Limits specified for Caution: Permanent hearing loss may occur
point-to-point and non-point-to-point operation as appropriate. if earphones or headphones are used at high
(iv) Users should also be advised that high-power radars are volume for prolonged periods of time.
allocated as primary users (i.e. priority users) of the bands 5250- For France, the products have been tested to
5350 MHz and 5650-5850 MHz and that these radars could comply with Sound Pressure Level requirement
cause interference and/or damage to LE-LAN devices. laid down in the applicable NF EN 50332 L.5232-1.

Exposure of humans to RF fields (RSS-102) Note:

–– To prevent possible hearing damage, do not listen to high volume
The computers employ low gain integral antennas that do not levels for long periods.
emit RF field in excess of Health Canada limits for the general
population; consult Safety Code 6, obtainable from Health
Canada’s Website at http://www.hc-sc.gc.ca/ WEEE Notice
The radiated energy from the antennas connected to the wireless The Directive on Waste Electrical Equipment (WEEE), which
adapters conforms to the IC limit of the RF exposure requirement entered into force as European law on 14/02/2014, resulted in
regarding IC RSS-102, Issue 5 clause 4. SAR tests are conducted a major change in the treatment of electrical equipment at end-
using recommended operating positions accepted by the FCC/ of-life.
RSS with the device transmitting at its highest away from the The purpose of this Directive is, a first priority, the prevention of
body. Non-compliance with the above restrictions may result in WEEE, and in addition, to promote the reuse, recycling and other
a violation of FCC RF exposure guidelines. forms of recovery of such wastes as so as to reduce disposal.
The WEEE logo on the product or on its box indicating collection
Use Restriction: Attention in France, the operation is limited to
for electrical and electronic equipment consists of the crossed-
indoor use within the band 5150-5350 Mhz.
out wheeled bin, as shown below.
For Products with Radio Receivers That Can This product must not be disposed of or dumped with
Use an External Antenna (USA ONLY) your other household waste. You are liable to dispose
of all your electronic or electrical waste equipment by
CATV (Cable TV) or Antenna Grounding
relocating over to the specified collection point for
If an outside antenna or cable system is connected to this recycling of such hazardous waste. Isolated collection
product, be certain that it is grounded so as to provide some and proper recovery of your electronic and electrical waste
protection against voltage surges and static charges. Section equipment at the time of disposal will allow us to help conserving
810 of the National Electrical Code (NEC), ANSI/NFPA No. 700- natural resources. Moreover, proper recycling, and collection
1984, provides information with respect to proper grounding of points, please contact your local city center, household waste
the mast and supporting structure, grounding of the lead-in wire disposal service, shop from where you purchased the equipment,
to an antenna discharge unit, of grounding conductors, location or manufacturer of the equipment.
of antenna discharge unit, connection to grounding electrodes
and requirements of the electrode. RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the
Note to CATV System Installer
European Parliament and of the Council of 8 June 2011 on the
This reminder is provided to call the CATV(cable TV) system restriction of the use of certain hazardous substances in electrical
installer’s attention to article 820-40 of the NEC, which provides and electronic equipment.
guidelines for proper grounding and, in particular, as close to the
point of cable entry as possible.
For Products that includes Batteries
Caution: This product uses a laser system. To prevent direct EU Batteries Directive 2013/56/EU
exposure to the laser, do not open the cabinet enclosure or defeat
A new battery directive 2013/56/eu on Battery and Accumulator
any of the safety mechanisms provided for your protection. Do
replacing directive entered into force on the 01/07/2015. The
NOT START INTO THE LASER BEAM. To ensure proper use of
directive applies to all types of batteries and accumulator
this product, please read the owner’s manual carefully and retain
(AA, AAA, button cells, rechargeable packs) including those
it for future use. Should the unit require maintenance or repair,
incorporated into appliances except for military, medical
please contact your local JBL service. Refer servicing to qualified
and power tool applications. The directive sets out rules for
personnel only.
collection, treatment, recycling and disposal of batteries, and
aims to prohibit certain hazardous substances and to improve
environmental performance of batteries and all operators in the
supply chain.

www.jbl.com 3
 Instructions for Users on Removal, Recycling and Disposal HARMAN
of Batteries
The remove the batteries from your equipment or remote control, HARMAN International Industries, Incorporated
reverse the procedure described in the owner’s manual for 8500.255.4545 (USA only)
inserting batteries. For products with a built-in battery that lasts HARMAN International Industries, Incorporated. All rights
for the lifetime of the product, removal may not be possible for reserved. JBL is a trademark of HARMAN International Industries,
the user. In this case, recycling or recovery, it becomes necessary Incorporated, registered in the United States and/ or other
to replace such a battery, this procedure must be performed by countries. Features, specifications and appearance are subject
authorized services centers. In the European Union and other to change without notice.
locations, it is illegal to dispose of any battery with household
trash. All batteries must be disposed of in an environmentally
sound manner. Contact your local waste-management officials
for information regarding the environmentally sound collection, EPILEPSY
recycling and disposal of used batteries.
WARNING: Danger of explosion if battery is incorrectly replaced.
WARNING
To reduce risk of fire or burns, don’t disassemble, crush,
puncture, short external contact, expose to temperature above
A few people may experience epileptic
60°C (140°F), or dispose of in fire or water. Replace only with seizures when viewing flashing lights.
specified batteries. The symbol indicating ‘separate collection’
for all batteries and accumulators shall be crossed-out wheeled
bin shown below:
Precautions
Stand Mounting Safety Precautions
Always follow instruction and precaution advise from
In case of batteries, accumulators and button cells containing speaker stand manufacturer.
more than 0.0005 mercury, more than 0.002% cadmium or more Partybox 100 contains a 36 mm receptacle cup to allow mounting
than 0.004% lead, shall be marked with the chemical symbol for on tripod stands or on a pole over subwoofers. When using
the metal concerned: Hg,Cd or Pb respectively. Please Refer to stands or poles, be sure to observe the following precautions:
the below symbol: • Check the stand or pole specification to be certain the device
is designed to support the weight of the speaker. Observe all
safety precautions specified by the manufacturer.
• Always verify that the stand (or subwoofer/pole) is placed on
a flat, level and stable surface and be sure to fully extend the
legs of tripod type stands. Position the stand so that the legs
WARNING: DO NOT INGEST BATTERIES, CHEMICAL BURN do not present a trip hazard.
HAZARD [the remote supplied with] This product contains a coin/ Use this floor stand only on a flat, solid surface. Once the support
button cell battery. If the coin/button cell battery is swallowed, it (extended leg) has been placed and adjusted, carefully tighten
can cause severe international burns in just 2 hours and can lead the screws and use the safety pin. After placing the speaker
to death. Keep new and used batteries away from children. If you on the stand, check for stability: When tilting each direction to
think batteries might have been swallowed or placed inside any 10 degrees (for the surface), the speaker should not turn off. If
part of body, seek immediate medical attention. necessary, reduce the height of the speakers and extend the
base of the stand.
For All Products Except Those with Wireless • Route cables so that performers, production crew, and
Operation audience will not trip and topple the speakers over.
• Inspect the stand (or pole and associated hardware) before
HARMAN International hereby declares that this equipment is in each use and do not use equipment with worn, damaged or
compliance with EMC 2014/30/EU Directive, LVD 2014/35/EU missing parts.
Directive. The declaration of conformity may be consulted in the • Do not attempt to place more than one PartyBox series
support section of our Web Site, accessible from www.jbl.com. speaker on a stand or pole.
• Always be cautious in windy, outdoor conditions. It may
For All Products with Wireless Operation be necessary to place additional weight (i.e. sandbags) on
HARMAN International hereby declares that this equipment the base of the stand to improve stability. Avoid attaching
is in compliance with the essential requirements and other banners or similar items to any part of a speaker system.
relevant provisions of Directive 2014/53/EU. The declaration of Such attachments could act as a sail and topple the system.
conformity may be consulted in the support section of our Web • Unless you are confident that you can handle the weight of
Site, accessible from www.jbl.com. the speaker, ask another person to help you get it onto the
tripod stand or pole.

4
 English
TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS 2 7. CARRYING YOUR PARTYBOX 11

FEDERAL COMMUNICATION COMMISSION INTERFERENCE
STATEMENT 2

FOR PRODUCTS THAT TRANSMIT RF ENERGY 2 8. SETTINGS 11

8.1 TWS MODE 11
EXPOSURE OF HUMANS TO RF FIELDS (RSS-102) 3
8.2 DEMO MODE 11
FOR PRODUCTS WITH RADIO RECEIVERS THAT CAN USE
AN EXTERNAL ANTENNA (USA ONLY) 3 8.3 STANDBY MODE 11
FOR ALL EU COUNTRIES 3 8.4 SPEAKER MOUNTING 12
FOR PRODUCTS THAT INCLUDES BATTERIES 3

FOR ALL PRODUCTS EXCEPT THOSE WITH WIRELESS

OPERATION 4 9. SPECIFICATIONS 12
FOR ALL PRODUCTS WITH WIRELESS OPERATION 4

HARMAN 4
10. TROUBLESHOOTINGS 13

1. INTRODUCTION 6 11. COMPLIANCE 13

2. WHAT’S IN THE BOX 6 12. TRADEMARK 14

3. PRODUCT OVERVIEW 7
3.1 TOP PANEL 7

3.2 BACK PANEL 7

4. POWER ON 8

5. CHARGING 8
5.1 CHARGE YOUR SPEAKER 8

5.2 CHECK THE BATTERY LEVEL 8

6. USING YOUR PARTYBOX 9

6.1 BLUETOOTH CONNECTION 9

6.2 USB CONNECTION 9

6.3 AUX CONNECTION 9

6.4 MIX SOUND WITH A MICROPHONE OR GUITAR 10

6.5 CHARGING EXTERNAL USB DEVICES 10

www.jbl.com 5
 1. INTRODUCTION 2. WHAT’S IN THE BOX
Congratulations on your purchase! This manual includes
information about “JBL PARTYBOX 100” speaker. We
encourage you to take a few minutes to read this manual, which
describes the product and includes step-by-step instructions to
help you to set up and get started. Read and understand all the
safety instructions before using your product.
If you have any questions about these products, their installation
or their operation, please contact your retailer or customer
service, or visit us at www.jbl.com.

1) Main unit
2) Power cord*
3) Quick Start Guide, Safety sheet, Warranty card
*Power cord quantity and plug type vary by regions.

6
 English
LED behavior
3. PRODUCT OVERVIEW White (Constant) Power on
3.1 Top Panel Amber (Constant) Standby
Off Power off
White White (Regular flash) Pairing
White (Constant) Connected
7 Off Not connected
1 White (Constant) On
6 2
Off Off
3
Red (Slow flash) Low battery
5 4
White (Slow flash) Charging
White (Constant) Charged

3.2 Back Panel

1)
• Battery level indicator.
7
2)
• Press to power on or off. 6
1
3) 2 5
• Press to enter Bluetooth pairing mode. 4
3
• Press and hold for 20 seconds to forget all the paired
devices.
4) 1) USB
• Press to toggle between different light patterns. • Charge an external USB device.
• Press and hold for 2 seconds to turn the strobe light on • Connect to a USB storage device.
or off.
2) AUX
5) • Connect to an external audio device through an audio
• Press repeatedly to switch between bass boost level 1 cable.
and level 2 or turn off.
3) VOLUME (MIC)
6) / • Rotate the knob to adjust the microphone volume.
• Press to increase or decrease the volume level.
4) MIC
• Press both simultaneously to mute the audio output.
• Connect to a microphone (not provided).
7)
5) VOLUME (GUITAR)
• Press to play or pause the music.
• Rotate the knob to adjust the guitar volume.
Caution: 6) GUITAR
–– Do not look directly at the light-emitting parts when the speaker
lights are turned on.
• Connect to a guitar (not provided).
7) GAIN
• Guitar and microphone gain control buttons to match
different sensitivity of the mic and guitar.

www.jbl.com 7
 4. POWER ON 5. CHARGING
PartyBox is powered by a built-in rechargeable battery.
Cautions:
–– Use only provided power cord. Notes:
–– Fully charge the built-in battery before using for the first time, which
Plug one of the end Ac power cord into the Power connector will prolong the battery lifespan.
on the back speaker, then plug the other end to a wall outlet. –– Built-in battery charging works on AC power only.

5.1 Charge your Speaker

Use the AC power to charge your PartyBox 100

5.2 Check the Battery Level

The speaker is powered by the built-in rechargeable battery.
After power-on, the speaker shows the battery level immediately,
you can check the status of the PartyBox battery by pressing
on any button.

8
 English
6. USING YOUR PARTYBOX

6.1 Bluetooth connection

You can use your PartyBox as an external speaker for your
Bluetooth enabled smartphone or tablet.
1) Press to enter Bluetooth pairing mode.
2) Choose “JBL PartyBox 100” to connect.
3) Once successfully connected, audio will stream from your
Bluetooth device to this speaker.

1 2 Audio formats
Extension Codec Sample rate Bitrate
10m (33ft) 8 / 11.025
/ 12 / 16 / 384 / 529.2 / 576 /
WAVE PCM 22.05 / 24 768 / 1058.4 / 1152 /
/ 32 / 44.1 1536 / 2116.8 / 2304
Bluetooth
/ 48
Bluetooth

DEVICES 32 / 40 / 48 / 56 / 64 /
JBL PartyBox 100 MPEG1 32 / 44.1 80 / 96 / 112 / 128 /
layer2/3 / 48 160 / 192 / 224 / 256 /
320
Notes: 8 / 16 / 24 / 32 / 40 /
–– This speaker can memorize a maximum of 8 paired devices. The MP3 MPEG2 16 / 22.05
48 / 56 / 64 / 80 / 96 /
ninth paired device will replace the first one. layer2/3 / 24
112 / 128 / 144 / 160
–– If a PIN code is requested while connecting a Bluetooth device,
enter “0000”. 8 / 16 / 24 / 32 / 40 / 48 /
MPEG2.5 8 / 11.025 /
–– Bluetooth performance can be affected by the distance between 56 / 64 / 80 / 96 / 112 /
layer3 12
this product and your Bluetooth device and the environment of 128 / 144 / 160
operation. 5 / 6 / 8 / 10 / 12 / 16 /
8 / 11.025 / 20 / 22 / 32 / 36 / 40 /
To terminate the Bluetooth-enabled device: WMA 16 / 22.05 / 44 / 48 / 64 / 80 / 96 /
• Turn off this speaker; 32 / 44.1/48 128 / 160 / 192 / 256 /
• Disable Bluetooth on your device; or 320
• Move this speaker beyond the Bluetooth operational range.
To reconnect the Bluetooth-enabled device: 6.3 AUX connection
• When you turn on this speaker next time, it tries to reconnect
the last connected device automatically; Notes:
• If not, manually select “JBL PartyBox 100” on your Bluetooth –– When the USB source is not playing, Bluetooth can break in and
play music from the phone.
device to start a connection.
–– When USB is playing, Bluetooth cannot break in USB.
Note: –– Priority goes to USB, Bluetooth and then Aux.
–– To exit Bluetooth mode, insert a USB storage device.
To play music on your portable audio device through this
speaker, make sure that no Bluetooth connection or USB device
6.2 USB connection is available.
With your PartyBox, you can enjoy music that is stored on a 1) Connect a 3.5mm audio cable (not supplied) to:
USB storage device such as an MP3 player. • the headphone socket of your portable audio device;
Plug your USB storage device into the USB port of your PartyBox. • the AUX connector of this speaker.
The music will play automatically. If not, please check if the USB
device contains playable audio contents.

www.jbl.com 9
 2) Turn on your portable audio device and it starts playing. 6.5 Charging External USB Devices
You can use this speaker as a battery charger for your
rechargeable USB devices.
Connect your USB device to the USB port on the rear of this
speaker.
2
1

Note:
–– To exit AUX mode, choose Bluetooth or USB as a source first

6.4 Mix Sound with a Microphone or Guitar

By using a microphone (not supplied) or an electric guitar (not
supplied), you can mix its sound with an audio source.
1) Rotate counterclockwise the MIC/GUITAR volume knob to
turn down the volume.
2) Connect your microphone or guitar to the MIC/GUITAR jack
of this speaker.
3) Sing through the microphone or play guitar.
• To adjust the volume of the audio source, press / ;
• To adjust the volume of the microphone or guitar, rotate the
MIC/GUITAR volume knob.
To adjust the echo mic level when the mic is plugged:
• Press / to toggle the echo level (echo level 1 set as
default).
• Press / to switch from level 1 to level 2.
• Press / to turn off the echo level.

Caution:
–– When not using the microphone or guitar, decrease the MIC/
GUITAR volume to minimum and remove them from the jack.

10
 English
7. CARRYING YOUR PARTYBOX 8. SETTINGS
Cautions:
8.1 TWS Mode
–– Before carrying the speaker, make sure that all the cords are
disconnected. The two PartyBox 100 speakers can connect to each other in
–– To avoid personal injury and/or property damage, hold the product TWS mode.
firmly while carrying.
1) Press and hold on both speakers simultaneously for 5
seconds, you will hear a tone to indicate speakers are in
pairing mode. Once TWS connection built up, you will hear
another tone.
2) In TWS mode, press and hold for 5 seconds on either
speaker or power off the speaker to exit the TWS mode.

10m (33ft)

8.2 Demo Mode

Caution:
–– Ensure PartyBox is powered by AC to go into Demo Mode.
–– If the AC power unplugged, the PartyBox will power off. If the AC
power is resumed the PartyBox will automatically enter to the demo
mode.

To enter or to exit demo mode, press and hold and

simultaneously for 5 seconds.
In demo mode, all the input sources are disabled, all buttons but
/ / / are disabled.
Note:
–– The PartyBox built-in with 3 x 30 seconds music tracks.

Playback
• Press once to start, pause or resume the play (one sample
will be played only for 30 seconds).
• Press once after the pause, to play the next track.

8.3 Standby Mode

The product will enter into sleep mode after 20 minutes without
operation.
• If the“PartyBox” powered by the battery, it will auto power
off if no action for 20 minutes.
• If the “PartyBox” powered by AC or DC power source, the
product will enter standby mode if no action for 20 minutes.
Press (power) or Bluetooth stream break-in in standby mode,
the speaker will enter normal mode.

www.jbl.com 11
 8.4 Speaker mounting 9. SPECIFICATIONS
a) Speaker Stand • Product name: PartyBox 100
Place the ParyBox on speaker stands (sold separately) for • AC power input: 100 - 240 V ~ 50/60 Hz
general-purpose sound reinforcement. • Built-in battery: Li-ion 2500 mAh, 14.4 V
• Power consumption: 60 W
• Standby power consumption:
< 2 W with BT connecting;
< 0.5 W without BT connecting
• USB output: 5V 2.1A
• Speaker drivers: 2 woofers + 2 tweeters
• Speaker impedance: 4 Ω
• Total output power: 160 W
• Signal-to-noise (S/N) ratio: 80 dBA
• Frequency response: 45 Hz - 18 KHz (-6 dB)
• Battery charge time: 5 hours
• Battery playtime: 12 hours*
• Bluetooth version: 4.2
• Bluetooth profile: A2DP V1.3, AVRCP V1.6
• Bluetooth transmitter frequency range: 2402 - 2480 MHz
• Bluetooth maximum transmitter power: 15 dBm (EIRP)
• Bluetooth transmitter modulation: GFSK, π/4 DQPSK,
8DPSK
• Bluetooth range: Approx. 10 m (33 ft)
• USB format: FAT16, FAT32
• USB file format: .mp3, .wma, .wav
b) Using a Speaker Stand • Input sensitivity (AUX in): 370 mV rms (3.5 mm connector)
If you have purchased speaker stands, you can place the • Digital input: Bluetooth/USB -9 dBFS
speakers on the stands utilizing the pole mount adaptor built • Dimension (W x H x D): 288 x 551 x 290 mm /
into the PARTYBOX 100 speaker cabinets. 11.3 x 21.7 x 11.4 in
• Net weight: 9.7 kg / 21.4 lbs

*12 hrs battery playtime is only for reference and may vary
depending on music content and battery aging after numerous
charging and discharging cycles. It’s achievable with a predefined
music source, light show switch off, volume level at 7 and BT
streaming source.

12
 English
10. TROUBLESHOOTINGS 11. COMPLIANCE
The product is in compliance with the European Union energy
Caution:
legislation.
–– Never try to repair the product by yourself. If you have any
problems while using this product, check the following points Bluetooth connection mode
before you request service.
The product is intended to be used for streaming music via
System Bluetooth connection. A consumer can stream Bluetooth
The unit will not turn on. audio to the speaker. When the product is connected through
Bluetooth, the Bluetooth connection must remain active at all
• Check if the power cord is plugged into the outlet and to the
times to ensure proper operation.
PartyBox.
The product will enter into sleep mode (networked standby),
• Make sure the speaker is fully charged, if not use the power
after 20 minutes without operation, the power consumption @
cord to turn on your speaker.
sleep is less than 2.0 Watts, after which it can be re-activated
Sound via Bluetooth connection.
No sound from the PartyBox. Bluetooth disconnection mode
• Make sure that the PartyBox is powered on. The product will enter into standby mode, after 20 minutes
• Make sure that volume level is turned to an audible level. without operation, the power consumption @ standby is less
• Make sure that it is connected to a music source. than 0.5 Watts.
Bluetooth
A device cannot connect with the PartyBox.
• Check if you enable the Bluetooth function of the device.
• The PartyBox is already connected to another Bluetooth
device. Press and hold on Bluetooth to disconnect and pair
with a new device.
Poor audio quality from a connected Bluetooth device.
• The Bluetooth reception is poor. Move the device closer to
the PartyBox, or remove any obstacle between the device
and the PartyBox.

www.jbl.com 13
 12. TRADEMARK

Este equipamento não tem direito à proteção contra interferência

prejudicial e não pode causar interferência em sistemas devidamente
autorizados.
Este produto está homologado pela ANATEL, de acordo com os
procedimentos regulamentados pela Resolução 242/2000, e atende
aos requisitos técnicos aplicados.
Para maiores informações, consulte o site da ANATEL – www.anatel.
gov.br

The Bluetooth® word mark and logos are registered trademarks

owned by the Bluetooth SIG, Inc. and any use of such marks by
HARMAN International Industries, Incorporated is under license. Other
trademarks and trade names are those of their respective owners.

14
 English
Торговая марка : JBL
Назначение товара : Активная акустическая система
Изготовитель : Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик
Стрит 400, офис 1500
Страна происхождения : Китай
Импортер в Россию : OOO “ХАРМАН РУС СиАйЭс“, Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1
Гарантийный период : 1 год
Информация о сервисных центрах : www.harman.com/ru тел. +7-800-700-0467
Срок службы : 5 лет

Товар сертифицирован
Дата производства : Дата изготовления устройства определяется по двум буквенным обозначениям из второй группы
символов серийного номера изделия, следующих после разделительного знака «-». Кодировка
соответствует порядку букв латинского алфавита, начиная с января 2010 года: 000000-MY0000000,
где «M» - месяц производства (А - январь, B - февраль, C - март и т.д.) и «Y» - год производства (A -
2010, B - 2011, C - 2012 и т.д.).
Используйте устройство только по прямому назначению в соответствии с предоставленной инструкцией. Не пытайтесь самостоятельно
вскрывать корпус товара и осуществлять ремонт. В случае обнаружения недостатков или дефектов, обращайтесь за гарантийным
обслуживанием в соответствии с информацией из гарантийного талона. Особые условия хранения, реализации и (или) транспортировки
не предусмотрены. Избегайте воздействия экстремальных температур, долговременного воздействия влаги, сильных магнитных полей.
Устройство предназначено для работы в жилых зонах. Срок годности не ограничен при соблюдении условий хранения.

HARMAN International Industries, © 2019 HARMAN International Industries, Incorporated. All rights reserved.JBL is a trademark
Incorporated 8500 Balboa of HARMAN International Industries, Incorporated, registered in the United States and/or other
Boulevard, Northridge, CA 91329 countries. Features, specifications and appearance are subject to change without notice. The
USA Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
www.jbl.com any use of such marks by HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective owners. The terms HDMI, the
HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries. Manufactured under
license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.

JBL_PartyBox_100_OM_EN_V2

www.jbl.com 15