FOR Approval Specification: 32.0" Wxga TFT LCD Title
FOR Approval Specification: 32.0" Wxga TFT LCD Title
net
LC320WXN
Product Specification
SPECIFICATION
FOR
APPROVAL
( ) Preliminary Specification
( ● ) Final Specification
SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE
REVIEWED BY
PREPARED BY
Please return 1 copy for your confirmation with TV Product Development Dept.
your signature and comments. LG Display Co., Ltd
Ver. 1.0 1 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
CONTENTS
CONTENTS 2
RECORD OF REVISIONS 3
1 GENERAL DESCRIPTION 4
3 ELECTRICAL SPECIFICATIONS 6
4 OPTICAL SPECIFICATIONS 15
5 MECHANICAL CHARACTERISTICS 19
6 RELIABILITY 22
7 INTERNATIONAL STANDARDS 23
7-1 SAFETY 23
7-2 EMC 23
8 PACKING 24
9 PRECAUTIONS 25
9-5 STORAGE 26
Ver. 1.0 2 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
RECORD OF REVISIONS
Ver. 1.0 3 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
1. General Description
The LC320WXN is a Color Active Matrix Liquid Crystal Display with an integral External Electrode Fluorescent
Lamp(EEFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally black mode. It has a 31.51 inch diagonally measured
ac ti v e d is p la y a r ea w ith W XG A r es o lut i on ( 768 ve r t ic a l b y 1 366 hor i zont al pixel ar ra y).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in Horizontal stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus presenting a palette of more than 16.7M(true) colors.
It has been designed to apply the 8-bit 1-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.
EEPROM
S1 S1366
Power Circuit RGB
Block Source Driver Circuit
+24.0V
VBR-A, EXT.VBR-B
On/off ,Status Back light Assembly (12EEFL)
CN2, Inverter (Master, 14Pin, High)
General Features
Active Screen Size 31.51 inches(800.4mm) diagonal
Outline Dimension 760.0 mm(H) x 450.0 mm(V) x 48.0 mm(D) (Typ.)
Pixel Pitch 510.75㎛ x 170.25㎛ x RGB
Pixel Format 1366 horiz. by 768 vert. pixels RGB stripe arrangement
Color Depth 8bit, 16,7 M colors
Luminance, White 500 cd/m2 (Center 1 point) (Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178(Typ.), U/D 178(Typ.))
Power Consumption Total 87.7Watt (Typ.) (Logic=3.7 W, Inverter= 84W [VBR-A=1.65V] )
Weight 5,700g(Typ.)
Display Operating Mode Transmissive mode, normally black
Surface Treatment Hard coating(3H), anti-glare treatment of the front polarizer (Haze 10%)
Ver. 1.0 4 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
Value
Parameter Symbol Unit Remark
Min Max
Notes : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39 °C and no condensation of water.
2. Gravity mura can be guaranteed below 40℃ condition.
90%
60
60%
50 Storage
Humidity [(%)RH]
Wet Bulb
Temperature [°C]
40
40%
Operation
30
20
10
0
10%
-20 0 10 20 30 40 50 60 70 80
Ver. 1.0 5 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
3. Electrical Specifications
Value
Parameter Symbol Unit Note
Min Typ Max
Circuit :
Power Input Voltage VLCD 10.8 12.0 13.2 VDC
- 311 404 mA 1
Power Input Current ILCD
- 400 520 mA 2
Power Consumption PLCD - 3.73 4.85 Watt 1
Rush current IRUSH - - 3.0 A 3
Notes : 1. The specified current and power consumption are under the VLCD=12.0V, 25 ± 2°C, fV=60Hz
condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
Mosaic Pattern(8 x 6)
Ver. 1.0 6 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
Lamp:
Notes :
1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 120
minutes at 25±2°C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (VBR-A : 1.65V & ExtVBR-B : 100%), it is total power consumption.
The ripple voltage of the power supply input voltage is under 0.5 Vp-p. LGD recommend Input Voltage is
24.0V ± 5%.
2. Electrical characteristics are determined within 30 minutes at 25±2°C.
The specified currents are under the typical supply Input voltage 24V.
3. The brightness of the lamp after lighted for 5minutes is defined as 100%.
TS is the time required for the brightness of the center of the lamp to be not less than 95% at typical current.
The screen of LCD module may be partially dark by the time the brightness of lamp is stable after turn on.
4. Specified Values are for a single lamp which is aligned horizontally.
The life time is determined as the time which luminance of the lamp is 50% compared to that of initial value
at the typical lamp current (VBR-A : 1.65V & ExtVBR-B :100%), on condition of continuous operating at 25± 2°C
5. LGD recommend that the PWM freq. is synchronized with Two times harmonic of Vsync signal of system.
6. The duration of rush current is about 10ms.
Ver. 1.0 7 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
3-2. Interface Connections
This LCD module employs two kinds of interface connection, a 30-pin connector is used for the module
electronics and One connectors(14-pin) are used for the integral backlight system.
Ver. 1.0 8 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
14
…
…
Ver. 1.0 9 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
Note :
1. The input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode).
If you use spread spectrum of EMI, add some additional clock to minimum value for clock margin.
2. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate and the horizontal frequency
3. Timing should be set based on clock frequency.
Ver. 1.0 10 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
0.7VDD
DE, Data
0.3VDD
tCLK
0.5 VDD
DCLK
Valid data
First data Invalid data Pixel 0,0 Pixel 2,0 Invalid data
Valid data
Second data Invalid data Pixel 1,0 Pixel 3,0 Invalid data
DE(Data Enable)
tHV
tHT
1 768
DE(Data Enable)
tVV
tVT
Ver. 1.0 11 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED (001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Ver. 1.0 12 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
90% 90%
Power Supply For LCD
VLCD 10% 10%
0V
T1 T6
Valid Data
T2 T5
Invalid Invalid
30%
Interface Signal (Tx) Data Data
0V
T3 T4
Option Signal T7 T8
(LVDS_select)
T9 Lamp ON
Power for Lamp
Table 8. POWER SEQUENCE
Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - 20 ms
T2 0.5 - - ms 4
T3 200 - - ms 3
T4 200 - - ms 3
T5 0 - - ms
T6 2.0 - - s 5
T7 0.5 - T2 ms 4
T8 0 - - ms 4
T9 T2 + T3 - 5 s
Ver. 1.0 13 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
VBL
10% 0.7V
0V
VON/OFF Lamp ON
T4 T4
VBR-A &
Ext. VBR-B T7
VBL(Typ) x 0.8
0 V
Table 9. Power Sequence for Inverter
Values
Parameter Units Remarks
Min Typ Max
T1 20 - - ms 1
T2 500 - - ms
T3 200 - - ms 2
T4 0 - ms
T5 10 - - ms
T6 - - 10 ms VBL(Typ) x 0.8
T7 1000 - - ms 3
Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.
2. T4(max) is less than T2.
3. In T7 section, EXTVBR-B is recommended 100%.
Ver. 1.0 14 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and for 60 minutes in a dark environment at
25±2°C. The values are specified at an approximate distance 50cm from the LCD surface at a viewing angle of
Φ and θ equal to 0 °.
FIG. 1 shows additional information concerning the measurement equipment and method.
LCD Module Pritchard 880 or
Optical Stage(x,y)
equivalent
50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method
Table 10. OPTICAL CHARACTERISTICS
Ta= 25±2°C, VLCD=12.0V, fV=60Hz, Dclk=72.4MHz, VBR-A =1.65V, Ext. VBR-B =100%
Value
Parameter Symbol Unit Note
Min Typ Max
Contrast Ratio CR 800 1200 - 1
Surface Luminance, white LWH 400 500 cd/m2 2
Luminance Variation δ WHITE 5P - - 1.3 3
Gray-to-Gray G to G - 8 12 ms 4
Response Time
Uniformity δ G TO G - - 1 5
Rx 0.639
RED
Ry 0.333
Gx 0.292
GREEN
Color Coordinates Gy Typ 0.604 Typ
[CIE1931] Bx -0.03 0.145 +0.03
BLUE
By 0.064
Wx 0.279
WHITE
Wy 0.292
Viewing Angle (CR>10)
x axis, right(φ=0°) θr 89 - -
x axis, left (φ=180°) θl 89 - -
degree 6
y axis, up (φ=90°) θu 89 - -
y axis, down (φ=270°) θd 89 - -
Gray Scale 2.2 7
Ver. 1.0 15 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
2. Surface luminance are determined after the unit has been ‘ON’ and 60min after lighting the
backlight in a dark environment at 25±2°C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.
5. Gray to Gray Response time uniformity is Reference data. Please see Appendix XI.
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 4.
7. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 11.
Ver. 1.0 16 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
Measuring point for surface luminance & measuring point for luminance variation.
H
A
② ③
①
V
B
④ ⑤ A : H / 4 mm
B : V / 4 mm
@ H,V : Active Area
Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Gray(M)”.
Tr Tf
100
90
Optical
Response
10
Gray(N) Gray(M) Gray(N)
0
N,M = 0(Black)~255(White), N<M
Ver. 1.0 17 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
Normal
E Y
φ = 90 ° , Up
φ = 180 ° , Left
θ
φ = 0 ° , Right
φ = 270 ° , Down
Ver. 1.0 18 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
5. Mechanical Characteristics
Item Value
Horizontal 760.0mm
Depth 48.0 mm
Horizontal 703.8mm
Bezel Area
Vertical 398.4mm
Horizontal 697.685mm
Active Display Area
Vertical 392.256mm
Note : 1.Please refer to a mechanical drawing in terms of tolerance at the next page.
Ver. 1.0 19 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
<FRONT VIEW>
Ver. 1.0 20 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
<REAR VIEW>
Ver. 1.0 21 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
6. Reliability
Table 13. ENVIRONMENT TEST CONDITION
Note : Before and after Reliability test, LCM should be operated with normal function.
Ver. 1.0 22 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
7. International Standards
7-1. Safety
a) UL 60065, 7th Edition, dated June 30, 2003, Underwriters Laboratories, Inc.,
Standard for Audio, Video and Similar Electronic Apparatus.
b) CAN/CSA C22.2, No. 60065:03, Canadian Standards Association,
Standard for Audio, Video and Similar Electronic Apparatus.
c) IEC60065:2001, 7th Edition CB-scheme and EN 60065:2002,
Safety requirements for Audio, Video and Similar Electronic Apparatus..
7-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992
b) CISPR13 "Limits and Methods of Measurement of Radio interference characteristics of Sound
and Television broadcast receivers and associated equipment"
CISPR22 "Limits and Methods of Measurement of Radio interference characteristics of Information
Technology Equipment" International Special Committee on Radio Interference.
c) EN55013 "Limits and Methods of Measurement of Radio interference characteristics of Sound and
Television broadcast receivers and associated equipment"
EN55022 "Limits and Methods of Measurement of Radio interference characteristics of Information
Technology Equipment" European Committee for Electro Technical Standardization.(CENELEC),
1988(Including A1:2000)
Ver. 1.0 23 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
8. Packing
8-1. Information of LCM Label
a) Lot Mark
A B C D E F G H I J K L M
Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
Mark 1 2 3 4 5 6 7 8 9 0
2. MONTH
Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C
Ver. 1.0 24 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
Ver. 1.0 25 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
Ver. 1.0 26 / 26
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX-I-1
■ Required signal assignment for Flat Link Transmitter(Pin9=“L” or NC”)
Vsync 28
Data Enable 30
LCD Module
CLOCK 31
Notes:
1. The LCD module uses a 100 Ohm(Ω) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 1.0 A- 1 / 15
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX-I-2
■ Required signal assignment for Flat Link Transmitter(Pin9=“H”)
Vsync 28
Vcc
Data Enable 30
LCD Module
CLOCK 31
Notes:
1. The LCD module uses a 100 Ohm(Ω) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 1.0 A- 2 / 15
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- Ⅱ-1
■ LC320WXN-SBA1 Packing Ass’y
Ver. 1.0 A- 3 / 15
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- Ⅱ-2
■ LC320WXN-SBA1 Pallet Ass’y
2 PALLET Plywood
Box quantity per pallet: 4ea 3 BAND PP
Pallet size: L1030 x W870 x H1210
4 CLIP, BAND STEEL
5 ANGLE, PACKING PAPER (SWR4)
6 LABEL PAPER
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- III
■ LCM Label
LC320WXN
Model
(SB)(A1)
RoHS Verified
Serial No.
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- IV
LC320WXN
SBA1 LC320WXN
6 PCS
KOREA
SBA1
24 PCS
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- V
T-Con
#28 : VBR-
VBR-B Input
#10 : OPC Enable Pin #27 : OPC-
OPC-OUT
#1 30
System
LCM OPC On
3.3V
Master
Inverter VBR-
VBR-B PWM
OPC Off ( Async.
Async. or Sync.)
14 13
11
VBR-A
NC / 1.65V
VDD
Input MAX 1Khz VDD*0.9
Frequency (Recommendation:50~300Hz) Rising Time
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- VI
Normal
System Von Lamp turn on Status level low
Mode
Inverter
Status
Status [14pin]
1sec
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- VII
Ω
1KΩ
Selector (Pin 9) Selector
Ω
50KΩ
ASIC
(TCON)
VCC
Open
R1 Ω
1KΩ
OPC_Enable
OPC_Enable
(Pin 10)
Ω
50KΩ
ASIC
(TCON)
System Side
R1 ≤ 1KΩ
Ω
LCM Side
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- VIII-1
2. AC Specification
Tclk A
LVDS Clock
80%
A
LVDS Data
20%
( Fclk = 1/T clk ) tRF
tSKEW tSKEW
Notes : 1. All Input levels of LVDS signals are based on the EIA 644 Standard.
2. If tRF isn’t enough, teff should be meet the range.
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- VIII-2
360ps
0.5tui tui
V+ data
V- data
360ps
tui : Unit Interval
teff
V+ clk
Vcm
V- clk
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- IX
RCLKP
RCLKM
RAP R13’ R12’ G12 R17 R16 R15 R14 R13 R12 G12”
RBP G14’ G13’ B13 B12 G17 G16 G15 G14 G13 B13”
RCP B15’ B14’ DE VSYNC HSYNC B17 B16 B15 B14 DE”
RCLKP
RCLKM
RAP R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”
RBP G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B15”
RCP B13’ B12’ DE VSYNC HSYNC B15 B14 B13 B12 DE”
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- X-1
The deep dimming must be used very carefully due to limitation of lamp characteristics and specification.
1) For stable lamp on, its duty condition should follow below the condition.
After Inverter ON signal, T0 duration should be sustained.
Output current
LAMP ON
Inverter ON signal
2) Low duty(0%~20%) of the inverter output current, B/L may not satisfy some of LCM specification.
- Duration : the low duty operation(0 ~ 20%) must be limited within 10 minutes for one time operation.
- Ratio : the period of the low duty operation must be less than 1/5 compare to that of the high duty
operation(20~100%) in a certain period to prevent unwanted operation.
- FOS : partial darkness or darkness of center area during the low duty might be happened due to
insufficient lamp current.
- Warm up : the low duty must be used 3 min after the lamps “ON”. In case of low temperature, more
warm up time may be needed.
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- X-2
Output current
T0 T1 T2 T3 T2
Value
Parameter Unit Note
Min Typ Max
3) The output current duty may not be same as input PWM duty due to rise/fall time of output.
Note : 1. To make Mega DCR > 50000:1, VBR-A and PWM duty must be given by system.
2. DCR >50000:1 is defined mathematically as :
DCR = Maximum DCRn (n=1, 2, 3, 4, 5)
Surface Luminance at position n with all white pixels (PWM duty =0~20%, VBR-A=1.65V)
DCRn =
Surface Luminance at position n with all black pixels (PWM duty =0~20%, VBR-A=1.65V)
www.DataSheet4U.net
www.DataSheet4U.net
LC320WXN
Product Specification
# APPENDIX- XI
2. G to G Uniformity
The variation of G to G Uniformity , δ G to G is defined as :
Maximum(GtoG ) − Typical (GtoG )
G to G Uniformity = ≤1
Typical (GtoG )
*Maximum (GtoG) means maximum value of measured time (N, M = 0 (Black) ~ 255(White), 32 gray step).
5. Current Status
Below table is actual data of production on 09. 27, 2008
12 12 G191 G159
G191 G159
8 8
G127 G95
G127 G95
Not measured
4
G159
G255
G63 G31
Not measured
4
G159
G255
G63 G31
0
0 G63
G255
G223
G63
G191
G255
G159
G223
G127
G191
G95
G159
G63
G127
G0
G31
G95
G0
G63
G31
G0
G0
<#1> <#2>
Ver. 1.0 41/ /15
A- 15 26
www.DataSheet4U.net